Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 28 views

    WT7984 - CSP Instruction For Use - en

    Uploaded by

    German Restrepo

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    WT7984 - CSP Instruction For Use - en

    Uploaded by

    German Restrepo
    28 views2 pages

    Original Title

    WT7984_CSP-Instruction-for-use_en

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    28 views2 pages

    WT7984 - CSP Instruction For Use - en

    Uploaded by

    German Restrepo

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    www.contitech.

    de/cbg-csp-e one step – one solution


    Conti Secur® PREMIUM
    Instructions for Use

    Conti Secur PREMIUM ®

    The one-component adhesive based on polychloroprene.

    Rubber-to-rubber adhesion

    1. Preparation of the cold bonding


    1.1 Clean the surface of the rubber using cleansing agent (CCS).
    Allow the cleaning agent to evaporate off for at least 10 minutes
    at room temperature.

    1.2 Roughen the surface of the rubber using a grinder.

    Caution: Minimum speed: 800 U/Min.


    Maximum speed: 2000 U/Min.

    Remove the grinding dust dry.

    2. Bonding
    2.1 The surfaces or materials that are to be glued should preferably be at room temperature.
    If the temperature is too low, we recommend warming up the surfaces/materials.

    2.2 First application of Conti Secur ® PREMIUM onto the gluing surfaces
    Using a brush with short bristles, apply one thin coat of Conti Secur ® PREMIUM
    to the prepared rubber surfaces.
    Drying time: At least 30 minutes at room temperature

    Caution: At room temperature the maximum drying time


    should not exceed 12 hours.

    2.3 Second application of Conti Secur ® PREMIUM to the gluing surfaces


    Drying time: Maximum of 10 minutes at room temperature (test with back of hand).
    Note: A third application of adhesive may be required if the surface is particularly rough.
    The drying time for the second application is then also at least 30 minutes.

    2.4 Put the surfaces to be glued together. Press on the surfaces from the inside outwards,
    e.g. using a hand-held roller. The required contact pressure depends on the properties
    of the surfaces.
    WT 7984 E 10.12

    Caution: Brief contact pressure is sufficient. Optimum adhesion strength


    is attained after approx. 24 hours.

    The content of this publication is not legally binding and is provided as information only. The trademarks
    displayed in this publication are the property of Continental AG and/or its affiliates. Copyright © 2012 ContiTech AG.
    All rights reserved. For complete information go to: www.contitech.de/discl_en

    Conveyor Belt Group


    ContiTech Transportbandsysteme GmbH
    D-37154 Northeim
    Tel. +49 5551 702-1643
    transportbandsysteme@cbg.contitech.de
    www.contitech.de/cbg-csp-e one step – one solution
    Conti Secur® PREMIUM
    Instructions for Use

    Conti Secur PREMIUM ®

    The one-component adhesive based on polychloroprene.

    Rubber-to-metal adhesion
    - Contact layer material -
    1. Preparation of the cold bonding
    1.1 Clean the surface of the metal and the contact layer using cleansing agent (CCS).

    Caution: If the rubber coating with the contact layer material has been stored
    for a longer period of time, we recommend roughening the surface of the contact
    layer material with a grinding disk (grade 40 or 60).

    1.2 Roughen the metal surface by sand-blasting or with the aid of an angle grinder.
    Grit of the grinding disk: 16 or 24. Remove the grinding dust dry.

    2. Bonding
    2.1 Thoroughly stir the adhesive agent CONTI PLUS® prior to processing,
    and apply one thin coat to the metal surface.
    Drying time: At least 30 minutes at room temperature

    Caution: Coated parts can be stored up to a maximum


    of 2 weeks at room temperature.

    2.2 Apply one coat of Conti Secur ® PREMIUM to the metal surface.
    Drying time: At least 30 minutes at room temperature

    Caution: Do not use a brush with short bristles, as otherwise


    the CONTI PLUS® coating could come off again.

    2.3 Cut the rubber coating to size.


    Second application of Conti Secur ® PREMIUM on the metal surface.

    2.4 One coating of Conti Secur ® PREMIUM onto the surface of the contact layer.
    Drying time: Maximum of 10 minutes (test with back of hand).

    2.5 Put the coated surfaces together. Press on the surfaces from the
    inside outwards, e.g. using a hand-held roller or a dead-blow hammer.
    WT 7984 E 10.12

    Caution: Brief contact pressure is sufficient.


    Optimum adhesion strength is attained after approx. 24 hours.

    The content of this publication is not legally binding and is provided as information only. The trademarks
    displayed in this publication are the property of Continental AG and/or its affiliates. Copyright © 2012 ContiTech AG.
    All rights reserved. For complete information go to: www.contitech.de/discl_en

    Conveyor Belt Group


    ContiTech Transportbandsysteme GmbH
    D-37154 Northeim
    Tel. +49 5551 702-1643
    transportbandsysteme@cbg.contitech.de

    You might also like