CA3059
CA3059
CA3059
CA3059
ZERO VOLTAGE SWITCH
SEMICONDUCTOR TECHNICAL DATA
Relay Control Valve Control Heater Control Lamp Control OnOff Motor Switching Differential Comparator with SelfContained Power Supply for Industrial Applications Synchronous Switching of Flashing Lights
14 1
2 RS 5 AC Input
ORDERING INFORMATION
VCC
Device
Limiter Power Supply Zero Crossing Detector VCC Current Boost 3 RL
CA3059
MT2
Triac Drive
4 Gate
MT1
13
9 * RX 10 11
* NTC Sensor
Gnd
1 Inhibit
6 External Trigger
CA3059
MAXIMUM RATINGS
Rating DC Supply Voltage (Between Pins 2 and 7) DC Supply Voltage (Between Pins 2 and 8) Peak Supply Current (Pins 5 and 7) FailSafe Input Current (Pin 14) Output Pulse Current (Pin 4) (Note 1) Junction Temperature Operating Temperature Range Storage Temperature Range Symbol VCC 12 VCC 12 I5,7 I14 Iout TJ TA Tstg 50 2.0 150 150 40 to + 85 65 to + 150 mA mA mA C C C Vdc Value Unit Vdc
ELECTRICAL CHARACTERISTICS (Operation @ 120 Vrms, 5060 Hz, TA = 25C [Note 2])
Characteristic DC Supply Voltage Inhibit Mode RS = 10 k, IL = 0 RS = 5.0 k, IL = 2.0 mA Pulse Mode RS = 10 k, IL = 0 RS = 5.0 k, RL = 2.0 mA Gate Trigger Current (VGT = 1.0 V, Pins 3 and 2 connected) Peak Output Current, Pulsed With Internal Power Supply, VGT = 0 Pin 3 Open Pins 3 and 2 Connected With External Power Supply, VCC = 12 V, VGT = 0 Pin 3 Open Pins 3 and 2 Connected Inhibit Input Ratio (Ratio of Voltage @ Pin 9 to Pin 2) Total Gate Pulse Duration (CExt = 0) Positive dv/dt Negative dv/dt Pulse Duration After Zero Crossing (CExt = 0, RExt = R) Positive dv/dt Negative dv/dt Output Leakage Current Inhibit Mode (Note 3) Input Bias Current Co Common Mode Input Voltage Range o ode u o age a ge (Pins 9 and 13 Connected) Inhibit Input Voltage External Trigger Voltage Figure 2 Symbol VS 6.1 6.0 3 3 IGT IOM 50 90 4 5 6 tp tn 6 tp1 tn1 3 7 8 I4 IIB VCMR V1 V6V4 50 60 0.001 0.15 1.4 to 5.0 1.4 1.4 10 1.0 1.6 A A Vdc Vdc Vdc 70 70 100 100 140 140 s V9/V2 0.465 230 300 0.485 0.520 s 125 190 6.5 6.1 6.4 6.2 160 7.0 7.0 mA mA Min Typ Max Unit Vdc
NOTES: 1. Care must be taken, especially when using an external power supply, that total package dissipation is not exceeded. 2. The values given in the Electrical Characteristics Table at 120 V also apply for operation at input voltages of 24 V, 208/230 V, and 277 V, except for Pulse Duration test. However, the series resistor (RS) must have the indicated value, shown in Table A for the specified input voltage. 3. I4 out of Pin 4, 2.0 V on Pin 1, S1 position 2.
http://onsemi.com
2
CA3059
TEST CIRCUITS
(All resistor values are in ohms)
RS 10 k AC Line 7 9 10 11
4.6 k 13 2
RS AC Line
Figure 3. Peak Output (Pulsed) and Gate Trigger Current with Internal Power Supply
10
11
RS 10 k 120 Vrms 60 Hz
13 12
4 7
13
14
R1 100 F
R2
Gate Pulse Positive dv/dt Zero Voltage tP1 tP 120 Vrms 60 Hz RS 10 k CExt 5 7
tN1 10 11 4 1k 13 2 tN
VCC = 6.0 V 2
+ 3.0 V
9 IIB 13 7 8
12 RExt
8 5k
5k 100 F
Figure 6. Gate Pulse Duration Test Circuit with Associated Waveform http://onsemi.com
3
CA3059
TYPICAL CHARACTERISTICS
10 k
9 10 1 1 2
300 250 200 150 100 50 0 5.0 120 Vrms, 60 Hz Gate Voltage = 0 8.0 9.0 10 6.0 7.0 11 EXTERNAL POWER SUPPLY VOLTAGE (V) 12 Pins 2 and 3 Connected Pin 3 Open
7 8
14 13
39 k VI
R1 5k
R2 5k
Figure 9. Peak Output Current (Pulsed) versus External Power Supply Voltage
140
- 40
- 20
20
40
60
80
100
0.52 7.0 6.8 6.6 6.4 6.2 6.0 - 40 - 20 0 20 40 60 80 100 Inhibit Mode V9 /V 2, INHIBIT VOLTAGE RATIO VS, INTERNAL SUPPLY (V) 0.50 0.48 0.46 0.44 0.42 0.40
120 Vrms, 60 Hz
- 40
- 20
80
100
http://onsemi.com
4
CA3059
RP CF 100 F 15 V + 2 Inhibit Input 1 Rx NTC Sensor 13
10 k 10
70 A AC Line Input RS 5 85 k
35 A
30 k 30 k 30 k 53 A 150 A 50 k
5k 4 To Thyristor Gate
14 Fail-Safe Input
7 To Common
APPLICATION INFORMATION
Power Supply
The CA3059 is a selfpowered circuit, powered from the AC line through an appropriate dropping resistor (see Table A). The internal supply is designed to power the auxiliary power circuits. In applications where more output current from the internal supply is required, an external power supply of higher voltage should be used. To use an external power supply, connect Pin 5 and Pin 7 together and apply the synchronizing voltage to Pin 12 and the DC supply voltage to Pin 2 as shown in Figure 4.
Operation of Protection Circuit
b. Sensor Resistance (RX) and RP values should be between 2 k and 100 k. c. The relationship 0.33 < RX/RP < 3 must be met over the anticipated temperature range to prevent undesired activation of the circuit. A shunt or series resistor may have to be added.
External Inhibit Function
A priority inhibit command applied to Pin 1 will remove current drive from the thyristor. A command of at least +1.2 V @ 10 A is required. A DTL or TTL logic 1 applied to Pin 1 will activate the inhibit function.
DC Gate Current Mode
The protection circuit, when connected, will remove current drive from the triac if an open or shorted sensor is detected. This circuit is activated by connecting Pin 13 to Pin 14 (see Figure 1). The following conditions should be observed when the protection circuit is utilized: a. The internal supply should be used and the external load current must be limited to 2 mA with a 5 k dropping resistor.
When comparator operation is desired or inductive loads are being switched, Pins 7 and 12 should be connected. This connection disables the zerocrossing detector to permit the flow of gate current from the differential sensing amplifier on demand. Care should be exercised to avoid possible overloading of the internal power supply when operating the device in this mode. A resistor should be inserted between Pin 4 and the thyristor gate in order to limit the current.
http://onsemi.com
5
CA3059
PACKAGE DIMENSIONS
PLASTIC PACKAGE CASE 64606 ISSUE M
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 18.80 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --10_ 0.38 1.01
14
B
1 7
A F N T
SEATING PLANE
L C
K H G D 14 PL 0.13 (0.005)
M
J M
DIM A B C D F G H J K L M N
http://onsemi.com
6
CA3059
Notes
http://onsemi.com
7
CA3059
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
http://onsemi.com
8
CA3059/D
This datasheet has been downloaded from: www.DatasheetCatalog.com Datasheets for electronic components.