LICENCE

for
IP 344:1988 (R2010) Determination Of Light Hydrocarbons In Stabilized Crude Oils - Gas
Chromatography Method

Licensee: Azecolab
Date: 01-Jun-2018

COPYRIGHT NOTICE

This material is electronically reproduced by SAI Global under license from the Energy Institute who retain full copyright in the document.

No part of the printed publication, nor any part of this electronic file, may be reproduced or transmitted in any form, including transmittal by e-
mail, by file transfer protocol (FTP), or by being made part of a network-accessible system, without the prior written permission of the Publisher
or SAI Global.

SAI Global makes no guarantees or warranties as to the correctness of the document or as to the results arising from the purchase and use of
the document and is not responsible for problems in the delivery of the document. Any difficulties or queries should be addressed to SAI Global
below.

In USA and Canada Contact:-

SAI Global, Forest Road Office Centre, 210 Route 4 East, Paramus, NJ 07652, USA

Toll Free 1-888-454-2688 or 201-986-1131

Fax: 201-986-7886
E-mail: uspubsales@saiglobal.com
Web: http://infostore.saiglobal.com/store/

In Europe Contact:-

SAI Global, Index House, Ascot, Berks, SL5 7EU, UK

Phone: +44 (0)1344 636400

Fax: +44 (0)1344 291194
E-mail: standards@saiglobal.com
Web: http://infostore.saiglobal.com/store/

In Asia/Pacific Contact:-

SAI Global - Information Services, Level 37, 680 George Street, Sydney NSW 2000, Australia

Phone: 131 242 (within Australia) | +61 2 8206 6010 (outside Australia)
Fax: 1300 65 49 49 (within Australia) | +61 2 8206 6020 (outside Australia)
E-mail: sales@saiglobal.com
Web: http://infostore.saiglobal.com/store/

To read the full licence agreement, simply click within the red box above and scroll through with your cursor

Learn about LexConnect, All Jurisdictions, Standards referenced in Australian legislation

Know when a Standard has changed
Visit our store to find more Publications
 IP 344/88
(2010)

Determination of light hydrocarbons in stabilized crude oils

— Gas chromatography method

1 Scope 3.8 Air and hydrogen, free from water and

hydrocarbons.
This method covers the quantitative determination
of the individual hydrocarbons in stabilized crude 4 Apparatus
oils up to and including the pentanes. The hexanes
are determined as a group. 4.1 Gas chromatograph, with a heated flame
ionization detector and an injection port heater
WARNING — The use of this standard may involve capable of maintaining a temperature of 150°C.
Licensed to Azecolab on 01-Jun-2018. 1 user personal license only. Copying, copy/pasting, storage & distribution or use on network prohibited.

hazardous materials, operations and equipment. This

standard does not purport to address all of the 4.2 Integrator, an electronic integrator or
safety problems associated with its use. It is the computer system is required. It should have a count
responsibility of the user of this standard to rate of not less than 1 count per microvolt second.
establish appropriate safety and health practices and
determine the applicability of regulatory limitations 4.3 Recorder, a recording potentiometer for
prior to use. qualitative monitoring of the chromatogram only.
Get permission to copy from or network this publication www.saiglobal.com/licensing

2 Principle 4.4 Columns, a 2 m x 2,3 mm internal diameter

column packed with Porapak Q used in conjunction
A known amount of an internal standard, 2,2- with a 100 mm x 2,3 mm internal diameter
dimethylbutane, is added to the stabilized crude. A pre-column also packed with Porapak Q.
sample of this mixture is introduced by syringe into
a gas chromatographic (GC) column via a pre- NOTE - Means may be provided for back-flushing the
pre-column, or the packing may be disposed of after a
column both packed with Porapak Q. The hydro-
maximum of 10 injections. The analysis column may also
carbons are separated individually up to 2,2-
be back-flushed. Suitable back-flushing systems are
dimethylbutane and the hexanes are recorded as a shown in Annex A.
group. The concentrations of the individual hydro-
carbons and the hexane group, based on per cent 4.5 Syringes, 10 :l and 500 :l.
weight, are calculated by comparing the peak areas
with that of the internal standard. 4.6 Glass vials, with silicone rubber seals,
preferably PTFE-coated.
3 Reagents and materials
5 Apparatus preparation
Use only reagents of recognised analytical grade.
5.1 Column
3.1 Porapak Q, 80-100 mesh.
Degrease a 2 m length of clean stainless-steel
3.2 n-pentane tubing of 2,3 mm internal diameter.

3.3 2,2-Dimethylbutane, 99% pure. 5.1.1 Packing the column

3.4 2,3-dimethylbutane, 95% pure. 5.1.1.1 Bend the column (no bend being of less
than 50 mm in diameter) so as to be suitable for
3.5 Cyclohexane, 95% pure. fitting into the chromatograph.

3.6 Heptane 5.1.1.2 Insert a small glass wool plug into one end
of the tube and feed the Porapak Q into the other
3.7 Carrier Gas, nitrogen or helium, free from end by means of a funnel. An even distribution of
water and hydrocarbons. the packing may be achieved by gently vibrating the

344.1
 LIGHT HYDROCARBONS IN CRUDE OILS BY GAS CHROMATOGRAPHY, IP 344

column whilst appplying suction. Approximately 6.4 Shake the vial vigorously for at least 1 min
2,5 g of Porapak Q are required to pack the column. to completely mix the crude and internal standard.

5.1.1.3 Pack and prepare the 100 mm pre-column NOTE - Crude samples should be stored in a refrigerator
in the same manner as the main column. There will before an analysis. The preparation of internal standard
be no need to bend the pre-column. blend may be done at ambient temperature, but care
should be taken to minimize loss of light ends.
5.1.2 Column conditioning
7 Procedure
Connect the pre-column and main column together
and fit into the gas chromatograph. Do not connect 7.1 Inject 1 to 5:l as necessary, of the crude oil
the outlet end to the detector. Condition the column plus internal standard on to the column. Start the
until the base line drift resulting from column bleed recorder and integrator at the same time as
is less than 1% of full-scale deflection at a column injection.
temperature of 150°C and at the working
sensitivity. NOTE - The sample size should be as large as possible,
consistent with the linear range of the system, in order to
Licensed to Azecolab on 01-Jun-2018. 1 user personal license only. Copying, copy/pasting, storage & distribution or use on network prohibited.

NOTE - A suitable procedure for conditioning is to give a large signal-to-noise ratio.

maintain the column at 230°C for 12 h. During this time
the carrier gas should be flowing through the column but 7.2 The components are identified from the
the column should not be connected to the detector. chromatogram. A typical example is given in Figure
1. Terminate the analysis after cyclohexane has
5.1.3 Column performance eluted. The column may then be back-flushed or the
column temperature raised to 230°C for 30 min to
Using the experimental conditions set out in 5.2, remove any heavier components.
Get permission to copy from or network this publication www.saiglobal.com/licensing

record the chromatogram of a mixture of 1% wt

each of n-pentane (3.2), 2,2-dimethylbutane (3.3), 7.3 Measure the peak areas.
2,3-dimethylbutane (3.4) and cyclohexane (3.5) in
heptane (3.6). NOTE - A constant baseline is essential for accurate
quantitative work. In this method drifting of baseline may
NOTE - The ratio of valley to peak height for the be caused by heavy components from a previous injection
dimethylbutane peaks should be less than 15%. The breaking through the pre-column. Other factors such as
response factors for pentane and cyclohexane should be leaks, septum and column bleed should be checked.
within 5% of each other. Cyclohexane should be eluted
in less than 30 min.

5.2 Chromatograph

Typical operating conditions are:

Column temperature 150°C

Injection temperature 150°C
Detector 200°C
Carrier gas 25 ml/min

6 Sample preparation

6.1 Weigh a glass vial (4.6) and cap to the

nearest 0,1 mg.

6.2 Pour approximately 10 ml of crude oil into Figure 1: Typical chromatogram

the vial, seal immediately and reweigh to the
nearest 0,1 mg.
8 Calculation
6.3 Add approximately 200 :l of 2,2-dimethyl-
butane (3.3) by syringe (4.5) through the silicone Calculate the concentration of the individual
rubber seal in the vial cap and reweigh to the hydrocarbons and the hexane group using the
nearest 0,1 mg. following equation:

344.2
 LIGHT HYDROCARBONS IN CRUDE OILS BY GAS CHROMATOGRAPHY, IP 344

⎡ Ac × Ws ⎤ correct operation of the test method, exceed the

Component, % wt = ⎢ ⎥ 100 × RF values given in Table 2 in absolute value in only one
⎣ As × Wo ⎦ case in twenty.

where 10.3 Reproducibility, R

Ac is the peak area of component;
As is the peak area of internal standard; The difference between two single and independent
Ws is the weight of internal standard; test results, obtained by different operators working
Wo is the weight of crude oil; in different laboratories on identical test material,
RF is the response factor for carbon would in the long run, in the normal and correct
number (see Table 1). operation of the test method, exceed the values
given in Table 2 in only one case in twenty.
Table 1: Response factors
Table 2: Precision
Carbon no. Response
factor Hydrocarbon Range of r R
results X
Licensed to Azecolab on 01-Jun-2018. 1 user personal license only. Copying, copy/pasting, storage & distribution or use on network prohibited.

1 1,114
2 1,047 Ethane 0,01-0,06 0,155X 0,390X

3 1,023 Propane 0,12-0,69 0,066X 0,209X

4 1,012 Iso butane 0,16-0,32 0,056X 0,148X

5 1,005 Normal butane 0,11-1,70 0,045X 0,132X

6 1,000 Iso pentane 0,15-0,96 0,047X 0,090X

Get permission to copy from or network this publication www.saiglobal.com/licensing

Normal pentane 0,08-1,88 0,038X 0,103X

Cyclo pentane 0,07-0,28 0,048X 0,157X
9 Expression of results
Total hexanes 1,13-5,10 0,22 0,45

Report the results for the individual hydrocarbons up

to and including cyclopentane and for the total where X is the average of the two results being
hexane group to the nearest 0,01 % wt, Method compared.
IP 344.
11 Test report
10 Precision
The test report shall contain at least the following
10.1 General information:

The precision values (as defined in IP 367) have a) a reference to this standard;
been obtained by statistical examination of
inter-laboratory results and were first published in b) the type and complete identification of the
1988. product tested;

10.2 Repeatability, r c) the result of the test (see clause 9);

The difference between two test results, obtained d) any deviation, by agreement or otherwise,
by the same operator with the same apparatus from the procedure specified;
under constant operating conditions on identical test
material would in the long run, in the normal and e) the date of the test.

344.3
 LIGHT HYDROCARBONS IN CRUDE OILS BY GAS CHROMATOGRAPHY, IP 344

Annex A
(informative)

A.1 Back-flush of column and pre-column A.2 Back-flush of pre-column only

See Figure A.2 for arrangement for back-flush of

See Figure A.1 for arrangements for back-flush of pre-column only. The carrier gas flows at A and B
column and pre-column. The valve and transfer lines and the vent restrictor are set so that the flow
must be heated. through the analysis column is the same in both
positions of the valve.
Licensed to Azecolab on 01-Jun-2018. 1 user personal license only. Copying, copy/pasting, storage & distribution or use on network prohibited.

Figure A.1: Arrangement for back-flush of Figure A.2: Arrangement for back-flush of
column and pre-column pre-column only
Get permission to copy from or network this publication www.saiglobal.com/licensing

344.4