Technical Data Sheet

LOCTITE ECI 1010 E&C

March-2018

PRODUCT DESCRIPTION GENERAL INFORMATION

LOCTITE ECI 1010 E&C provides the following product For safe handling information on this product, consult the Safety
characteristics: Data Sheet, (SDS).
Technology Thermoplastic
Appearance Gray paste DIRECTIONS FOR USE
Filler Type Silver 1. Surface Preparation
Product Benefits ● Flexible ● Clean surface thoroughly prior to application.
● Good adhesion 2. Mixing/Dilution
● High conductivity ● Mix thoroughly before use to ensure it is homogenous. A slow
speed propeller may be utilized to mix until product is uniform.
Operating Temperature- 100ºC
Maximum ● If needed, the ink can be diluted with Butyl glycol acetate.
Cure Hot air drying 3. Application
Application Conductive Ink ● LOCTITE ECI 1010 E&C may be applied by screen printing
method.
Typical Assembly Flexible printed circuits, RFID and other
Applications conductive circuits ● Recommended screen and printing parameters are:
Key Substrates PET substrates Screen TypePolyester screen Polyester screen
Screen mesh 160 to 200 mesh
Emulsion Thickness , µm 10 to 40
LOCTITE ECI 1010 E&C is a screen printable, conductive ink .
Squeegee Hardness 70 to 90

TYPICAL PROPERTIES OF UNCURED MATERIAL CLEAN-UP

Solids Content (TGA), % 62 1. The equipment can be cleaned with esters (butylacetate,
Density, g/ml 2.1 ethylacetate) or ketones (MIBK, MEK).
Viscosity @ 1.5 s-1 , Rheometer, mPa∙s (cP) 9,000
Thixotropic Index (15/1.5 s-1 ) 1.9 STORAGE:
Theoretical coverage @ 10 µm dry film thickness, 10.6 Store product in the unopened container in a dry location. Storage
m²/kg information may be indicated on the product container labeling.
Shelf Life @ 2 to 8°C (from date of manufacture), 365
Optimal Storage: 2 to 8°C. Storage below 0°C or above 30°C can
days
adversely affect product properties.
Flash Point - See SDS
Material removed from containers may be contaminated during use.
TYPICAL CURING PERFORMANCE Do not return product to the original container. Henkel Corporation
cannot assume responsibility for product which has been contaminated
Recommended Drying Cycle
or stored under conditions other than those previously indicated. If
15 minutes @ 120°C or additional information is required, please contact your local Technical
2minutes @ 150°C Service Center or Customer Service Representative.
LOCTITE ECI 1010 E&C can be dried using forced air or infrared
systems. Higher temperatures for longer time exposure will improve Not for product specifications
the performance. Care should be taken with infrared. Too much The technical data contained herein are intended as reference only.
energy can destroy the coating. Design drying rates for the maximum Please contact your local quality department for assistance and
the substrate and production speeds can tolerate. recommendations on specifications for this product.

The above drying profile is a guideline recommendation. Conditions Conversions

(time and temperature) may vary based on customers' experience (°C x 1.8) + 32 = °F
and their application requirements, as well as customer drying kV/mm x 25.4 = V/mil
equipment, oven loading and actual oven temperatures. mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
TYPICAL PROPERTIES OF CURED MATERIAL psi x 145 = N/mm²
Physical Properties MPa = N/mm²
N·m x 8.851 = lb·in
Adhesion, Cross Hatch, grade 5B N·m x 0.738 = lb·ft
Electrical Properties N·mm x 0.142 = oz·in
mPa·s = cP
Sheet Resistance, ohm/sq/25 µm 0.007
 TDS LOCTITE ECI 1010 E&C, March-2018

Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.

In case products are delivered by Henkel Corporation, Resin Technology

Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
over whose methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from sale or use
of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
domination of patents owned by others or as a license under any Henkel
Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.

Trademark usage: [Except as otherwise noted] All trademarks in this document

are trademarks and/or registered trademarks of Henkel and its affiliates in the
U.S. and elsewhere.

Reference 2

Americas Europe Asia

+1.888.943.6535 +32.1457.5611 +86.21.3898.4800
For the most direct access to local sales and technical support visit: www.henkel.com/electronics