PROPRIETARY NOTE

THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE

REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HF AND
MUST BE RETURNED TO BOE HF UPON ITS REQUEST

SPEC. NUMBER PRODUCT GROUP ISSUE DATE PAGE

Rev. O
S864-6018 TFT MODULE 2011.6.9 1 OF 30

TITLE : B3 HM215WU1-500
Product Specification
Rev. 0

HEFEI BOE OPTOELECTRONICS TECHNOLOGY

R2010-6053-O(1/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 2 OF 30

REVISION HISTORY
REV. ECN No. DESCRIPTION OF CHANGES DATE PREPARED
0 Initial Release 2011.05.25 向贤明

R2010-6053-O(2/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 3 OF30

Contents
No. Item Page
1.0 General Description 4
2.0 Absolute Maximum Ratings 6
3.0 Electrical Specifications 7
4.0 Optical Specifications 8
5.0 Interface Connection 10
6.0 Signal Timing Specifications 14
7.0 Signal Timing Waveforms of Interface Signal 16
8.0 Input Signals, Display Colors & Gray Scale of Colors 18
9.0 Power Sequence 19
10.0 Mechanical Characteristics 20
11.0 Reliability Test 21
12.0 Handling& Cautions 22
13.0 Product Serial Number 23
14.0 Packing 24
15.0 Appendix 27

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 4 OF30

1.0 GENERAL DESCRIPTION

1.1 Introduction
HM215WU1-500 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 21.5 inch
diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this
module is adapted for a low reflection and higher color type.

LVDS LVDS Rx Source Driver

Input +
Signal T/CON
+
Connector (CN

Gate Driver

Mini LVDS Tx
TFT LCD Panel
1920 × 1080
VDD DC/DC
1 Gamma
)

Vcom CN2
LED Light Bar

1.2 Features

LVDS Interface with 2 pixel / clock

High-speed response

6-bit (Hi-FRC) color depth, display 16. 7M colors

Incorporated edge type back-light (Lower side - One Light Bar)

High luminance and contrast ratio, low reflection and normal viewing angle

DE (Data Enable) only

RoHS Compliant

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 5 OF30

1.3 Application

Desktop Type of PC & Workstation Use

Slim-Size Display for Stand-alone Monitor

Display Terminals for Control System

Monitors for Process Controller

1.4 General Specification

The followings are general specifications at the model HM215WU1-500.

<Table 1. General Specifications>

Parameter Specification Unit Remarks

Active area 476.64(H) × 268.11 (V) mm

Number of pixels 1920(H) ×1080(V) pixels
Pixel pitch 0.24825(H) ×0.24825(V) mm
Pixel arrangement RGB Vertical stripe
Display colors 16.7M colors
Display mode Normally White
Dimensional outline 495.6(H) × 292.2(V) × 10.2(D) typ. mm
Weight 1450 (Typ.) g
Surface Treatment Haze 25%, 3H
Back-light Lower side 1-LED Light bar Type

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 6 OF30

2.0 ABSOLUTE MAXIMUM RATINGS

The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.

< Table 2. Absolute Maximum Ratings> [VSS=GND=0V]

Symbol Min. Max. Unit Remarks
Parameter

Power Supply Voltage VDD -0.5 5.5 V

Ta = 25 ℃
Logic Supply Voltage VIN VSS-0.3 VDD+0.3 V

Operating Temperature TOP 0 +50 ℃ 1)

Storage Temperature TST -20 +60 ℃ 1)

Note : 1) Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 OC max. and no condensation of water.
100
90 (39,90)

80
Relative Humidity (%RH)

60
(50,50)
O p e ra tin g R a n g e
40
(60,30)

20
S to ra g e R a n g e
5

-2 0 0 20 40 60 80
T e m p e ra tu re (C̊ )

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 7 OF30

3.0 ELECTRICAL SPECIFICATIONS

3.1Electrical Specifications
< Table 3. Electrical specifications > [Ta =25±2 ℃]

Parameter Min. Typ. Max. Unit Remarks

Power Supply Voltage VDD 4.5 5.0 5.5 V
Note1
Power Supply Current IDD - 700 1200 mA

In-Rush Current IRUSH - - 3 A Note 2

Permissible Input Ripple Voltage VRF - - 100 mV VDD = 5.0V
High Level Differential Input
VIH - - +100 mV
Threshold Voltage

Low Level Differential Input

VIL -100 - - mV
Threshold Voltage

Differential input voltage |VID | 200 - 600 mV

VIH=100mV,
Differential input common mode voltage Vcm 1.0 1.2 1.5
VIL=-100mV

LED Channel Voltage VL 46.4 51.2 57.6 V

LED Channel Current IL 57 60 63 mA

LED Lifetime 30,000 - - Hrs

PD - 3.5 - W

Power Consumption PBL - 12.29 - W IL=60 mA, Note 5

Ptotal - 15.79 - W

Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=5.0V, Frame rate=75HZ. Test Pattern of power
supply current
a) Typ : Color Bar pattern
b) Max : Skip Sub Pixel Pattern

2. Duration of rush current is about 2 ms and rising time of VDD is 520 μs ± 20 %

3. The lamp frequency should be selected as different as possible from the horizontal
synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display
4. The voltage above this value should be applied to the lamps for more than 1 second to start-up. Otherwise the
lamps may not be turned on.
5. Calculated value for reference (VL × IL) ×4(channel) excluding driver loss. (LED Light bar: 16S4P)

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 8 OF30

4.0 OPTICAL SPECIFICATION

4.1 Overview
The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature =
25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall
be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer
to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (=
θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or
Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30
minutes warm-up period. VDD shall be 5.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock.

4.2 Optical Specifications

[VDD = 5.0V, Frame rate = 60Hz, Clock = 78MHz, IBL = 240mA, Ta =25±2 ℃]
Parameter Symbol Condition Min. Typ. Max. Unit Remark
Θ3 35 45 - Deg.
Horizontal
Θ9 35 45 - Deg.
Viewing Angle range CR > 10
Θ12 20 25 - Deg.
Vertical
Θ6 35 40 - Deg.
Note 1
Θ3 50 - - Deg.
Horizontal
Θ9 50 - - Deg.
Viewing Angle range CR > 5
Θ12 30 - - Deg.
Vertical
Θ6 45 - - Deg.
Luminance Contrast ratio CR 450 600 Note 2
Luminance of White Yw 160 200 cd/m2 Note 3
White luminance uniformity ΔY 75 80 % Note 4
Wx 0.283 0.313 0.343
White Θ = 0°
Wy 0.299 0.329 0.359
(Center)
Rx Normal 0.602 0.632 0.662
Red Viewing
Reproduction Ry 0.310 0.340 0.370
Angle Note 5
of color Gx 0.303 0.333 0.363
Green
Gy 0.596 0.626 0.656
Bx 0.127 0.157 0.187
Blue
By 0.013 0.043 0.073

Response Rising Tr 1.5 2.5 ms

Note 6
Time Falling Tf 3.5 5.5 ms
Cross Talk CT - - 2.0 % Note 7

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 9 OF30

Note :

1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are
determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock
direction with respect to the optical axis which is normal to the LCD surface.
2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD
surface. Luminance shall be measured with all pixels in the view field set first to white, then
to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio
(CR) is defined mathematically.

CR = Luminance when displaying a white raster

Luminance when displaying a black raster

3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with
all pixels in the view field set first to white. This measurement shall be taken at the locations
shown in FIGURE 2 for a total of the measurements per display.
4. The White luminance uniformity on LCD surface is then expressed as :
ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * 100
(See FIGURE 2 shown in Appendix).
5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral
data measured with all pixels first in red, green, blue and white. Measurements shall be made
at the center of the panel.
6. The electro-optical response time measurements shall be made as FIGURE 3 shown in
Appendix by switching the “data” input signal ON and OFF. The times needed for the
luminance to change from 10% to 90% is Td, and 90% to 10% is Tr.
7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the
luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the
luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4
shown in Appendix).

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 10 OF30

5.0 INTERFACE CONNECTION.

5.1 Electrical Interface Connection

● CN1 Module Side Connector : UJU IS100-L300-C23 or Equivalent

User Side Connector : JAE FI-X30H or Equivalent

Pin No Symbol Function Remark

1 RXO0- Negative Transmission data of Pixel 0 (ODD)
2 RXO0+ Positive Transmission data of Pixel 0 (ODD)
3 RXO1- Negative Transmission data of Pixel 1 (ODD)
4 RXO1+ Positive Transmission data of Pixel 1 (ODD)
5 RXO2- Negative Transmission data of Pixel 2 (ODD)
6 RXO2+ Positive Transmission data of Pixel 2 (ODD)
7 GND Power Ground
8 RXOC- Negative Transmission Clock (ODD)
9 RXOC+ Positive Transmission Clock (ODD)
10 RXO3- Negative Transmission data of Pixel 3 (ODD)
11 RXO3+ PositiveTransmission data of Pixel 3 (ODD)
12 RXE0- Negative Transmission data of Pixel 0 (EVEN)
13 RXE0+ Positive Transmission data of Pixel 0 (EVEN)
14 GND Power Ground
15 RXE1- Negative Transmission data of Pixel 1 (EVEN)
16 RXE1+ Positive Transmission data of Pixel 1 (EVEN)
17 GND Power Ground
18 RXE2- Negative Transmission data of Pixel 2 (EVEN)
19 RXE2+ Positive Transmission data of Pixel 2 (EVEN)
20 RXEC- Negative Transmission Clock (EVEN)
21 RXEC+ Positive Transmission Clock (EVEN)
22 RXE3- Negative Transmission data of Pixel 3 (EVEN)
23 RXE3+ Positive Transmission data of Pixel 3 (EVEN)
24 GND Power Ground Note1
25 NC Not connection, this pin should be open

26 NC Not connection, this pin should be open

27 NC Not connection
28 VDD1 Power Supply:+5V
29 VDD2
30 VDD3

Note 1：
1： This pin should be connected with GND

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 11 OF30

5.2 LVDS Interface (Tx; THC63LVDF83A or Equivalent)

5.2.1 ODD LVDS Interface

HM215WU1-500
Transmitter Interface Remark
Input (CN11)
Signal TFT-LCD
Pin No. Pin No. System (Tx) Pin No.
(Rx)
OR0 51
OR1 52
OR2 54
48 OUT0- RXO0- 1
OR3 55
47 OUT0+ RXO0+ 2
OR4 56
OR5 3
OG0 4
OG1 6
OG2 7
OG3 11
46 OUT1- RXO1- 3
OG4 12
45 OUT1+ RXO1+ 4
OG5 14
O OB0 15
D OB1 19
D
OB2 20
L OB3 22
V OB4 23
D 42 OUT2- RXO2- 5
OB5 24
S 41 OUT2+ RXO2+ 6
Hsync 27
Vsync 28
DE 30
MCLK 31 40 CLK OUT- RXO CLK- 8
39 CLK OUT+ RXO CLK+ 9
OR6 50
OR7 2
OG6 8 RXO3-
38 OUT3- 10
OG7 10 RXO3+
37 OUT3+ 11
OB6 16
OB7 18
RSVD 25

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 12 OF30

5.2.2 EVEN LVDS Interface

HM215WU1-500
Transmitter Interface Remark
Input (CN11)
Signal TFT-LCD
Pin No. Pin No. System (Tx) Pin No.
(Rx)
ER0 51
ER1 52
ER2 54
48 OUT0- RXE0- 12
ER3 55
47 OUT0+ RXE0+ 13
ER4 56
ER5 3
EG0 4
EG1 6
EG2 7
EG3 11
46 OUT1- RXE1- 15
EG4 12
45 OUT1+ RXE1+ 16
EG5 14
E
EB0 15
V
E EB1 19
N EB2 20
EB3 22
L
EB4 23
V 42 OUT2- RXE2- 18
D EB5 24
41 OUT2+ RXE2+ 19
S Hsync 27
Vsync 28
DE 30
MCLK 31 40 CLK OUT- RXE CLK- 20
39 CLK OUT+ RXE CLK+ 21
ER6 50
ER7 2
EG6 8 RXE3-
38 OUT3- 22
EG7 10 RXE3+
37 OUT3+ 23
EB6 16
EB7 18
RSVD 25

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 13 OF30

5.3 Data Input Format

(1,1) (2,1) (1919,1) (1920,1)

R G B R G B R G B R G B

1 Pixel = 3 Dots

R G B

R G B R G B R G B R G B

(1,1080) (2,1080) (1919,1080) (1920,1080)

Display Position of Input Data (V-H)

5.4 Back-light Interface Connection

●CN 2 LED LightBar Connector :CI1406M1HRL-NH or equivalent

Pin Function
1 Channel 1 Current Feedback
2 Channel 2 Current Feedback
3 LED Power Supply
4 LED Power Supply
5 Channel3 Current Feedback
6 Channel4 Current Feedback

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 14 OF30

6.0 SIGNAL TIMING SPECIFICATION

6.1 The HM215WU1-500 is operated by the DE only.

Item Symbols Min Typ Max Unit

Frequency 1/Tc 61.93 74.32 92.90 MHz

Clock High Time Tch - 4/7 Tc -
Low Time Tcl - 3/7 Tc -
1091 1125 1149 lines
Frame Period Tv 50 60 70 Hz
20 16.67 13.33 ms
Vertical Display Period Tvd - 1080 - lines
One line Scanning Period Th 1060 1100 1200 clocks
Horizontal Display Period Thd - 960 - clocks

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 15 OF30

6.2 LVDS Rx Interface Timing Parameter

The specification of the LVDS Rx interface timing parameter is shown in Table 4.

<Table 4. LVDS Rx Interface Timing Specification>

Item Symbol Min Typ Max Unit Remark

CLKIN Period tRCIP 10.76 13.46 16.15 nsec
Input Data 0 tRIP1 -0.4 0.0 +0.4 nsec
Input Data 1 tRIP0 tRCIP/7-0.4 tRCIP/7 tRCIP/7+0.4 nsec
Input Data 2 tRIP6 2 ×tRCIP/7-0.4 2 ×tRCIP/7 2 ×tRCIP/7+0.4 nsec
Input Data 3 tRIP5 3 ×tRCIP/7-0.4 3 ×tRCIP/7 3 ×tRCIP/7+0.4 nsec
Input Data 4 tRIP4 4 ×tRCIP/7-0.4 4 ×tRCIP/7 4 ×tRCIP/7+0.4 nsec
Input Data 5 tRIP3 5 ×tRCIP/7-0.4 5 ×tRCIP/7 5 ×tRCIP/7+0.4 nsec
Input Data 6 tRIP2 6 ×tRCIP/7-0.4 6 ×tRCIP/7 6 ×tRCIP/7+0.4 nsec

tRIP2
tRIP3
tRIP4
tRIP5
tRIP6
tRIP0

tRIP1

RXz +/- Rx3 Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0
* Z = 0, 1, 2,3

RxCLK+ Vdiff=0[v] Vdiff=0[v]

tRCIP

* Vdiff = (RXz+)-(RXz-),…. ,(RXCLK+)-(RXCLK-)

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 16 OF30

7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL

7.1 Sync Timing Waveforms

V-Sync Over 3 H-sync

H-Sync

Fix H-Sync width Area

DE

1) Need over 3 H-sync during V-Sync Low

2) Fix H-Sync width from V-Sync falling edge to first rising edge

7.2 Vertical Timing Waveforms

Tv

Tvd

MCLK

Th

DE

R7 ~ R0
G7 ~ G0 Invalid Data x,1 x,2 x,y x,1050 Invalid Data x+1,1
B7 ~ B0

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 17 OF30

7.3 Horizontal Timing Waveforms

Th
Thd

MCLK
Tc

DE

RA7 ~RA0
GA7 ~GA0
D1 D2 Dn D1048 D1049 D1050 Invalid Data D1 D2 D3
BA7 ~BA0

Tch Tcl
2.0V
MCLK 1.5V
0.8V

Tds Tdh

2.0V
Data Valid Data
0.8V
Tes

DE 2.0V

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 18 OF30

8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS

RED DATA GREEN DATA BLUE DATA

Color & Gray Scale
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Basic Colors
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Darker 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Gray Scale △ ↑ ↑ ↑
of RED ▽ ↓ ↓ ↓
Brighter 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
▽ 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
Gray Scale Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
△ ↑ ↑ ↑
of GREEN
▽ ↓ ↓ ↓
Brighter 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0
▽ 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Gray Scale Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
△ ↑ ↑ ↑
of BLUE
▽ ↓ ↓ ↓
Brighter 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1
▽ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
△ 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1
Darker 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0
Gray Scale
△ ↑ ↑ ↑
of WHITE
▽ ↓ ↓ ↓
Brighter 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0 1
▽ 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 19 OF30

9.0 POWER SEQUENCE

To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
shall be as shown in below

0.9VDD 0.9VDD
Power Supply 0.1VDD 0.1VDD
0V
T1
T3 T4
T2

Valid
Interface Signal
0V

T5 T6

Back- light 0V

● 0.5 ms ≤ T1 ≤ 10 ms
● 0 ≤ T2 ≤ 50 ms
● 0 ≤ T3 ≤ 50 ms
● 1 sec ≤ T4
● 200 ms ≤ T5
● 200 ms ≤ T6

Notes:
1. When the power supply VDD is 0V, keep the level of input signals on
the low or keep high impedance.
2. Do not keep the interface signal high impedance when power is on.
3. Back Light must be turn on after power for logic and interface signal are valid.

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 20 OF30

10.0 MECHANICAL CHARACTERISTICS

10.1 Dimensional Requirements

FIGURE 6 (located in Appendix) shows mechanical outlines for the model HM215WU1-500.
Other parameters are shown in Table 5.

<Table 5. Dimensional Parameters>

Parameter Specification Unit
Dimensional outline 495.6 ×292.2×10.2 mm
Weight 1450 (typ.) gram
Active area 476.64(H) × 268.11(V) mm
Pixel pitch 0.24825(H) x 0.24825(V) mm
Number of pixels 1920(H)×1080(V) (1 pixel = R + G + B dots) pixels
Back-light Lower side 1-LED Light bar Type

10.2 Mounting
See FIGURE 5. (shown in Appendix)

10.3 Anti-Glare and Polarizer Hardness.

The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce
scratching.

10.4 Light Leakage

There shall not be visible light from the back-lighting system around the edges of the screen as
seen from a distance 50cm from the screen with an overhead light level of 350lux.

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 21 OF30

11.0 RELIABLITY TEST

The Reliability test items and its conditions are shown in below.
<Table 6. Reliability Test Parameters >

No Test Items Conditions

1 High temperature storage test Ta = 60 ℃, 240 hrs

2 Low temperature storage test Ta = -20 ℃, 240 hrs

High temperature & high humidity

3 Ta = 50 ℃, 80%RH, 240hrs
operation test

4 High temperature operation test Ta = 50 ℃, 240hrs

5 Low temperature operation test Ta = 0 ℃, 240hrs
6 Thermal shock Ta = -20 ℃ ↔ 60 ℃ (0.5 hr), 100 cycle
Frequency 10 ~ 300 Hz, Sweep rate 30 min
Vibration test
7 Gravity / AMP 1.5 G
(non-operating)
Period X, Y, Z 30 min

Gravity 50G

Shock test
8 Pulse width 11msec, sine wave
(non-operating)

Direction ± X, ± Y, ± Z Once for each

Electro-static discharge test Air : 150 pF, 330Ω, 15 KV

9
(non-operating) Contact : 150 pF, 330Ω, 8 KV
Operating: 0 to 16400ft , 0 to 40°
10 Altitude test
Non Operating: 0 to 40000ft, -20 to 40°

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 22 OF30

12.0 HANDLING & CAUTIONS

(1) Cautions when taking out the module
 Pick the pouch only, when taking out module from a shipping package.
(2) Cautions for handling the module
 As the electrostatic discharges may break the LCD module, handle the LCD
module with care. Peel a protection sheet off from the LCD panel surface as
slowly as possible.
 As the LCD panel and back - light element are made from fragile glass material,
impulse and pressure to the LCD module should be avoided.
 As the surface of the polarizer is very soft and easily scratched, use a soft dry
cloth without chemicals for cleaning.
 Do not pull the interface connector in or out while the LCD module is operating.
 Put the module display side down on a flat horizontal plane.
 Handle connectors and cables with care.
(3) Cautions for the operation
 When the module is operating, do not lose CLK, ENAB signals. If any one of
these signals is lost, the LCD panel would be damaged.
 Obey the supply voltage sequence. If wrong sequence is applied, the module
would be damaged.
(4) Cautions for the atmosphere
 Dew drop atmosphere should be avoided.
 Do not store and/or operate the LCD module in a high temperature and/or
humidity atmosphere. Storage in an electro-conductive polymer packing pouch
and under relatively low temperature atmosphere is recommended.
(5) Cautions for the module characteristics
 Do not apply fixed pattern data signal to the LCD module at product aging.
 Applying fixed pattern for a long time may cause image sticking.
(6) Other cautions
 Do not disassemble and/or re-assemble LCD module.
 Do not re-adjust variable resistor or switch etc.
When returning the module for repair or etc., Please pack the module not to be
broken. We recommend to use the original shipping packages.

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 23 OF30

13.0 PRODUCT SERIAL NUMBER

HM215WU1-500

B3

1 2 3 4 5 6 7
X X X X X X X X X X X X X X X X X

1. Control Number( 2 digital or letter ) 5. Month (1,2,3, … , 9, X, Y, Z)

2. Rank / Grade (1 letter) 6. Internal Use (FG-code,4 digital)
3. Line Classification (B3 line:3 ) 7. Serial Number(000000—FFFFFF)
4. Year (2001 : 01, 2002 : 02, …)

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 24 OF30

14.0 Packing

14.1 Packing Order

As shown in the figure, place the

Put EPE Cushion into the box
modules bundled by packing bag
In the box

After sealing the box, attach Packing

Label on the attach position sign area
of the box. Place EPE cover on top of the box

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 25 OF30

14.2 Pallet Packing Order

Pile up the unit Box filled with

Load Pallet in correct position
Modules on the Pallet carefully
not to make a space.

Box cover Polyester bend

Out box

Adjust Outer box to piling Boxes

and cover the Outer box using box
cover. Bend Pallet Assy which is
putting the Box Cover tight in two
direction (horizontal and vertical) Wrap the Pallet Assy loaded
and two times using Polyester bend. 1story, 2stories from downside
through side and to edge of
upside. (12Boxes/Pallet)

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 26 OF30

14.3 Packing Specification and Note

 Box Dimension : 348(W) × 558mm(L) × 400mm(H)
 Package Quantity in one Box : 10pcs

Specification
Item Remark
Q'ty Dimension Weight (kg)

Panel 1 495.6(H) × 292.2(V) × 10.2(D) typ. 1.48 -

Cushion 1 - 0.70 -

Box 1 558(L)mm x 348(W)mm x 400(H)mm 0.70 without Panel & cushion

Packing Box 10pcs/Box 558(L)mm x 348W)mm x 400(H)mm 16.20 with panel & cushion

Pallet 1 1200(L)mm x 1140(W)mm x 120(H)mm 15.90 -

Pallet after Packing 12boxes/pallet 1140(L)mm x 1076W)mm x 820(H)mm 214 -

14.4 Box label

 Label Size : 108 mm (L) × 56 mm (W)
 Contents
Model : HM215WU1-500
Q`ty : Module Q`ty in one box
Serial No. : Box Serial No. See next page for detail description.
Date : Packing Date
FG Code : FG Code of Product

HM215WU1-500 10
0000000000000 201X.X.XX

5940

FG CODE RoHS
00 0 00 0 0 000000
Mark
Type Grade Year Month ITEM-CODE Serial_no

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 27 OF30

15.0 APPENDIX
Figure 1. Measurement Set Up

(L = 5 0 c m )

Figure 2. White Luminance and Uniformity Measurement Locations (9 points)

192 960 1728

108

540

972

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 28 OF30

Figure 3. Response Time Testing

Display data White(TFT OFF) Black(TFT ON) White(TFT OFF)

TR TF
100%
Optical
90%
Response

10%
0%
Time

Figure 4. Cross Modulation Test Description

VIEW AREA VIEW AREA

(D/4, W/4)

L31 YB(7D/8,W/2)

(3D/4, 3W/4)
(D, W) (D, W)
YA (7D/8,W/2)
L0

YB - YA
Cross-Talk (%) = × 100
YA

Where: YA = Initial luminance of measured area (cd/m2)

YB = Subsequent luminance of measured area (cd/m2)
The location measured will be exactly the same in both patterns

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 29 OF30

Figure 5. TFT-LCD Module Outline Dimensions (Front view)

)
(

R2010-6053-O(3/3) A4(210 X 297)

 PRODUCT GROUP REV ISSUE DATE

PRODUCT SPEC-TFT MODULE O 2011.6.9

SPEC. NUMBER SPEC. TITLE PAGE

S864-6018 B3 HM215WU1-500 Product Specification Rev. 0 30 OF30

Figure 6. TFT-LCD Module Outline Dimensions (Rear view)

LIGHT GUIDE : >PMMA<

HM215WU1 S1

B3

R2010-6053-O(3/3) A4(210 X 297)