Keensert Guide

SOSMETAL PRODUCTS INC.
HARDWARE
THREAD REPAIR
KEENSERTS
Strong, permanent thread repairs - No special drills, taps or installation tools required.
Install using standard drills and taps.

Easy hand installation.
Impossible to cross threads while installing.
No tang to break-off.
Positive mechanical lock against rotation.
May be used in virtually any material: Aluminum,
Magnesium, Cast Iron, Steel and Plastic.
Provides high strength & reliability, one length per size

provides maximum pullout strength, breaks Grade 8 bolts
in test after test.
Easy to remove.
No special skills required. Installation procedures can be
learned in minutes.
Quick and Easy to install...
Drill out old

threads, using
standard drill.
Tap new
threads, using
standard tap.
Screw in insert
until slightly
below surface.
Kees act as
depth stop.
* Drive Kees Finished.

down with
several light
taps.
* Use Keensert kee
drive or standard tools.
KEENSERT THREADED INSERT ASSORTMENTS
MASTER KEENSERTS & KEE DRIVERS

Sosmetal No.
COARSE & FINE THREADS
Sosmetal No.
713100
713103
Contains all coarse and fine

thread Keenserts and all
metric sizes plus one kee
driver per inside dia. size.
Contains all sizes of

Coarse & Fine
Thread Keenserts
#10 - 1/2
52 pieces
12 items
12043 plastic tray
107 pieces
28 items
12062 steel tray
SHOP
Sosmetal No.
713101
(Coarse)
Sosmetal No.
713102
(Fine)
Contains all sizes of

Keenserts #10 - 1/2
METRIC
Sosmetal No.
713104
Contains all metric

sizes: M6 -M10
25 pieces
5 items
12028 plastic tray
26 pieces
6 items
12028 plastic tray
A17-4
REVISED DECEMBER, 2005
Copyright 2005 Sosmetal Products Inc. All rights reserved.

No portion may be copied or reproduced in any manner.
SOSMETAL PRODUCTS INC.
HARDWARE
THREAD REPAIR
Sometimes when you compare cost alone, you dont realize the entire story. Other factors must be considered. Quality of material,
ease of installation, skill required and investment in special tools are all factors which favor keenserts over other inserts
and make keenserts your most cost effective repair.
MASTER KEENSERTS REFERENCE GUIDE
Internal
Thread Size
10-24
10-32
1/4-20
1/4-28
5/16-18
5/16-24
3/8-16
3/8-24
7/16-14
7/16-20
1/2-13
1/2-20
5/8-11
5/8-18
3/4-10
3/4-16
M5x0.8
M6x1.0
M8x1.0
M8x1.25
M10x1.25
M10x1.50
External
Thread Size
5/16-18
3/8-16
7/16-14
1/2-13
9/16-12
5/8-11
7/8-14
1-1/8-12
Keensert
Stock No.
713111
713112
713113
713114
713115
713116
713117
713118
713119
713120
713121
713122
713123
713124
713125
713126
M8x1.25
M10x1.25
M12x1.25
Drill Size &

Stock No.
I
813582
Q
813590
X
813597
29/64
813526
33/64
814755
37/64
814759
53/64
814775
1-1/16
814788
INSTALLATION DATA
Tap Size & Keenserts Kee
Stock No.
Driver
5/16-18
813815
3/8-16
813816
7/16-14
813817
1/2-13
813818
9/16-12
813819
5/8-11
813820
7/8-14
713131
713132
713133
713134
713135
713136
713137
1-1/8-28 713138
Metric Sizes
713161 H 813581 8x1.25

713162 S 813592 10x1.25
713164
27/64
713165 813524 12x1.25
713166
1/2
M14x1.50 713167
813529 14x1.50
REMOVAL DATA
Drill Size &
Stock No.
Drill Depth
7/32
813511
9/32
813515
11/32
813519
13/32
813523
15/32
813527
17/32
813654
25/32
813613
31/32
813622
713171 7/32 813511

713172 19/64 813516
3/8
713174
813521
29/64
713175
813526
5/32
3/16
3/16
3/16
3/16
3/16
3/16
3/16
5/32
3/16
3/16
SPARK PLUG KEENSERTS

INSTALLATION DATA
SPARK PLUG LENGTH
TAP
SIZE
(INCHES) DRILL DIA. TAP SIZE
(INCHES)
REFILL
SOSMETAL
NUMBER
713186
713187
713188
713189
713190
713191
713192
4
4
4
4
4
4
4
M10x1.0
M12x1.25
M12x1.25
M14x1.25
M14x1.25
M14x1.25
M14x1.25
1/2
1/2
3/4
3/8
7/16
1/2
3/4
REMOVAL DATA
DRILL
REFILL
SIZE
DEPTH WASHER
(INCHES) (INCHES) STOCK NO.
12 PER PAK
1/2 M14x1.5 29/64

37/64 M16x1.5 17/32
17/32
21/32
21/32
21/32
21/32
Copyright 2005 Sosmetal Products Inc. All rights reserved.

No portion may be copied or reproduced in any manner.
3/16
3/16
3/16
1/4
1/4
1/4
1/4
713193
713194
713194
713195
713195
713195
713195
Made from high-strength aluminum alloy,

Keenserts operate as well as the
original equipment.
Can be used with tapered seat or gasket
seat spark plugs.
Sealing washers (included in each kit)
provide a positive seal to prevent
compression loss from the
combustion chamber.
A17-5
REVISED DECEMBER, 2005

Keensert Guide

Uploaded by

Copyright:

Available Formats

Keensert Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Keensert Guide

Uploaded by

Copyright:

Available Formats

SOSMETAL PRODUCTS INC.

Install using standard drills and taps.

Provides high strength & reliability, one length per size

Quick and Easy to install...

Drill out old

* Drive Kees Finished.

KEENSERT THREADED INSERT ASSORTMENTS

MASTER KEENSERTS & KEE DRIVERS

COARSE & FINE THREADS

Contains all coarse and fine

Contains all sizes of

Contains all sizes of

Contains all metric

REVISED DECEMBER, 2005

Copyright 2005 Sosmetal Products Inc. All rights reserved.

SOSMETAL PRODUCTS INC.

MASTER KEENSERTS REFERENCE GUIDE

Drill Size &

713161 H 813581 8x1.25

713171 7/32 813511

SPARK PLUG KEENSERTS

1/2 M14x1.5 29/64

Copyright 2005 Sosmetal Products Inc. All rights reserved.

Made from high-strength aluminum alloy,

REVISED DECEMBER, 2005

You might also like