BRITISH STANDARD BS EN ISO

14122-2:2001

Safety of machinery —
Permanent means of
access to machinery —
Part 2: Working platforms and
walkways

The European Standard EN ISO 14122-2:2001 has the status of a

British Standard

ICS 13.110

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

BS EN ISO 14122-2:2001

National foreword

This British Standard is the official English language version of

EN ISO 14122-2:2001. It is identical with ISO 14122-2:2001. It partially
supersedes BS 5395-3:1985, and BS 4592-1 to -5, which are being amended to
address the requirements of this standard.
Recommendations on the design aspects of industrial type stairs, walkways,
platforms, fixed ladders and companion way ladders not addressed by this
standard can be found in BS 5395-3. Requirements for industrial type metal
flooring, walkways and stair treads that are not addressed by this standard can
be found in BS 4592-1 to -5, which covers the following:
— Part 1: Specification for open bar gratings;
— Part 2: Specification for expanded metal grating panels;
— Part 3: Specification for cold formed planks;
— Part 4: Specification for glass reinforced plastics open bar gratings;
— Part 5: Specification for solid plates in steel, aluminium and glass
reinforced plastics (GRP).
The UK participation in its preparation of EN ISO 14122 was entrusted by
Technical Committee B/208, Stairs and walkways, to Subcommittee B/208/1,
Stairs and walkways, Industrial stairs, which has the responsibility to:

— aid enquirers to understand the text;

— present to the responsible international/European committee any
enquiries on the interpretation, or proposals for change, and keep the
UK interests informed;
— monitor related international and European developments and
promulgate them in the UK.
A list of organizations represented on this committee can be obtained on
request to its secretary.
Cross-references
The British Standards which implement these international or European
publications may be found in the BSI Standards Catalogue under the section
entitled “International Standards Correspondence Index”, or by using the
“Find” facility of the BSI Standards Electronic Catalogue.
A British Standard does not purport to include all the necessary provisions of
a contract. Users of British Standards are responsible for their correct
application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
This British Standard, having
been prepared under the
direction of the Sector
Committee for Building and
Civil Engineering, was
published under the authority
of the Standards Committee
and comes into effect on Summary of pages
15 August 2001 This document comprises a front cover, an inside front cover, the EN ISO title
page, pages 2 to 13, and a back cover.
The BSI copyright date displayed in this document indicates when the
document was last issued.

© BSI 08-2001 Amendments issued since publication

Amd. No. Date Comments

ISBN 0 580 37015 1

EUROPEAN STANDARD EN ISO 14122-2
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2001

ICS 13.110

English version

Safety of machinery - Permanent means of access to machinery

- Part 2: Working platforms and walkways (ISO 14122-2:2001)

Sécurité des machines - Moyens d'accès permanents aux Sicherheit von Maschinen - Ortsfeste Zugänge zu
machines - Partie 2: Plates-formes de travail et passerelles maschinellen Anlagen - Teil 2: Arbeitsbühnen und
(ISO 14122-2:2001) Laufstege (ISO 14122-2:2001)

This European Standard was approved by CEN on 14 February 2000.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36 B-1050 Brussels

© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14122-2:2001 E
worldwide for CEN national Members.
Page 2
EN ISO 14122-2:2001

Contents

Foreword......................................................................................................................................................................3
Introduction .................................................................................................................................................................4
1 Scope ..............................................................................................................................................................5
2 Normative references ....................................................................................................................................5
3 Terms and definitions....................................................................................................................................6
4 General requirements....................................................................................................................................6
4.1 General............................................................................................................................................................6
4.1.1 Construction and materials ..........................................................................................................................6
4.1.2 Safety of operators ........................................................................................................................................7
4.2 Specific requirements ...................................................................................................................................7
4.2.1 Location ..........................................................................................................................................................7
4.2.2 Dimensions.....................................................................................................................................................7
4.2.3 Facilities or equipment..................................................................................................................................8
4.2.4 Floorings.........................................................................................................................................................8
4.2.5 Design loads.................................................................................................................................................10
5 Assembly instructions ................................................................................................................................10
Annex A (informative) Different methods of determining levels of slip-resistance ...........................................11
Annex ZA (informative) Relationship of this European standard with EC Directives .........................................12
Bibliography ..............................................................................................................................................................13
 Page 3
EN ISO 14122-2:2001

Foreword
The text of EN ISO 14122-2:2001 has been prepared by Technical Committee CEN/TC 114 "Safety of machinery",
the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 199 "Safety of
machinery".

This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by November 2001, and conflicting national standards shall be withdrawn at the latest
by November 2001.

This European Standard has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
Switzerland and the United Kingdom.
Page 4
EN ISO 14122-2:2001

Introduction
EN ISO 14122 consists of the following parts, under the general title "Safety of machinery - Permanent means of
access to machinery" :

Part 1 : Choice of a fixed means of access between two levels

Part 2 : Working platforms and walkways

Part 3 : Stairs, stepladders and guard-rails

Part 4 : Fixed ladders.

This part of EN ISO 14122 is a type B standard as stated in EN 1070.

This document is to be read in conjunction with clause 1.6.2 "Access to operating position and servicing points"
and 1.5.15 "Risk of slipping, tripping or falling" of the essential safety requirements expressed in annex A of
EN 292-2:1991/A1:1995. See also 6.2.4 "Provision for safe access to machinery" of EN 292-2:1991.

For the significant hazards covered by this standard, see clause 4 of EN ISO 14122-1.

The provisions of this document may be supplemented or modified by a type C standard.

NOTE 1 For machines which are covered by the scope of a type C standard and which have been designed and built
according to the provisions of that standard, the provisions of that type C standard take precedence over the provisions of this
type B standard.

The dimensions specified are consistent with established ergonomic data given in EN 547-3 "Safety of machinery - Human body
dimensions – Part 3 : Anthropometric data".

NOTE 2 The use of materials other than metals (composite materials, so-called "advanced" materials, etc.) does not alter the
application of the present standard.

Annexes A and ZA are for information only.

This part of EN ISO 14122 contains a Bibliography.

 Page 5
EN ISO 14122-2:2001

1 Scope
EN ISO 14122 defines the general requirements for safe access to machines mentioned in EN 292-2. Part 1 of EN
ISO 14122 gives advice about the correct choice of access means when the necessary access to the machine is
not possible directly from the ground level or from a floor.

This part of EN ISO 14122 applies to all machinery (stationary and mobile) where fixed means of access are
necessary.

This part of EN ISO 14122 applies to working platforms and walkways which are a part of a machine.

This part of EN ISO 14122 may also apply to working platforms and walkways to that part of the building where the
machine is installed, providing the main function of that part of the building is to provide a means of access to the
machine.

NOTE This part of EN ISO 14122 may be used also for means of access which are outside the scope of this standard. In
those cases the possible relevant national or other regulations should be taken into account.

This part of EN ISO 14122 applies also to working platforms and walkways specific to the machine which are not
permanently fixed to the machine and which may be removed or moved to the side for some operations of the
machine (e.g. changing tools in a large press).

This part of EN ISO 14122 does not apply to lifts, to moveable elevating platforms or other devices specially
designed to lift persons between two levels.

2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).

EN 292—1 (ISO/TR 12100-1), Safety of machinery — Basic concepts, general principles for design — Part 1 :
Basic terminology, methodology

EN 292-2/A1 (ISO/TR 12100-2), Safety of machinery — Basic concepts, general principles for design — Part 2 :
Technical principles and specifications

EN 294 (ISO 13852), Safety of machinery — Safety distances to prevent danger zones being reached by the upper
limbs

EN 547-1, Safety of machinery — Human body dimensions — Part 1 : Principles for determining the dimensions
required for openings for whole body access into machinery

EN 547-2, Safety of machinery — Human body dimensions — Part 2 : Principles for determining the dimensions
required for access openings

EN 547-3, Safety of machinery — Human body dimensions — Part 3 : Anthropometric data

EN 1070, Safety of machinery — Terminology

Page 6
EN ISO 14122-2:2001

EN ISO 14122-1, Safety of machinery — Permanents means of access to machinery — Part 1 : Choice of fixed
means of access between two levels

EN ISO 14122-3:2001, Safety of machinery — Permanents means of access to machinery — Part 3 : Stairs,
stepladders and guard-rails

3 Terms and definitions

For the purposes of this part of EN ISO 14122, the terms and definitions stated in EN 1070 "Safety of machinery -
Terminology" and of EN ISO 14122-1 apply.

The following additional definitions particularly required for this standard apply :

3.1
flooring
assembly of elements making up the floor of a walkway or a working platform and being in direct contact with
footwear

3.2
walkway
level surface used for moving from one point to another

3.3
working platform
level surface used for the operation, maintenance, inspection, repair, sampling and other phases of work in
connection with the machinery

3.4
slip resistant surface
flooring surface designed for improving the grip of footwear

4 General requirements
Walkways and working platforms shall comply with the following general safety requirements:

4.1 General

The working platforms and walkways shall be designed, constructed, located and where necessary protected so
that the operators are safe when having access to the working platforms and when they are on them for the
operation, setting, monitoring, repairing or any other work involved with the machinery.

4.1.1 Construction and materials

Working platforms and walkways shall be designed and constructed and the materials selected so that they
withstand the foreseeable conditions of use. In particular, at least the following details shall be considered:

a) dimensioning and selection of components (including fixings, connections, supports and foundations) to
ensure sufficient rigidity and stability;

b) resistance of all parts to environmental effects (such as climate, chemical agents, corrosive gases) e.g. by the
use of a corrosion resistant material or with the aid of a suitable protective coating;

c) positioning of constructional elements so that water cannot be accumulated e.g. in the joints;

d) use of compatible materials e.g. to minimise galvanic action or differential thermal expansion;

e) dimension of walkways and working platforms shall be according to available anthropometric data (see 4.2.2 of
this standard, see also EN 547-1 and EN 547-3);
 Page 7
EN ISO 14122-2:2001

f) walkways and working platforms shall be designed and constructed to prevent the hazards due to falling
objects. For guard-rails and toe plates, see clause 7 of EN ISO 14122-3:2001 and for openings in the flooring, see
4.2.4.4 of this standard;

g) the removal of any part of the machine shall, as far as practicable, be possible without removing guard-rails,
pieces of flooring or other permanent protective barriers.

4.1.2 Safety of operators

Walkways and working platforms shall be designed and constructed so that they are safe to use. In particular, the
following details shall at least be considered:

a) all parts likely to be in contact with operators shall be designed and built in such a way that the operator is
safe-guarded against injuries;

b) walkways and working platforms shall be designed and built in such a way that the walking surfaces have
durable slip resistant properties;

c) the parts of machinery which operators have to walk or stand on shall be designed and fitted out to prevent
persons falling from them (see EN ISO 14122-3);

d) working platforms and access to working platforms shall be laid out in such a way that operators can quickly
leave their workplace in the event of a hazard or can be quickly helped and easily evacuated when necessary;

e) handrails and other supports shall be designed, built and laid out in such a way that they are used instinctively.

4.2 Specific requirements

4.2.1 Location

As far as possible, walkways and working platforms shall be located away from the emission of harmful materials or
substances. The walkways and walking platforms shall also be located away from the accumulation of material,
such as earth, which is likely to cause slipping.

Where there are moving objects, non protected hot surfaces, unprotected live electrical equipment, etc., safety
distances shall be applied in accordance with EN 294.

Working platforms shall be located in such a way as to allow people to work in an ergonomic position, if possible,
between 500 mm and 1700 mm, above the surface of the working platform.

4.2.2 Dimensions

The clear length and width of walkways and working platforms intended for operation and maintenance shall be
determined by:

a) the demands of the task e.g. positions, nature and speed of movement, application of force, etc.;

b) whether or not tools, spare parts etc. are being carried;

c) frequency and duration of task and use;

Page 8
EN ISO 14122-2:2001

d) number of operators on walkways or working platforms at the same time ;

e) possibility of operators meeting ;

f) whether or not additional equipment such as safety clothing is being worn or personal protective equipment is
being carried ;

g) the presence of isolated obstacles ;

h) the evacuation of an injured person ;

i) walkway ending in a dead end ;

j) walls likely to damage or mark operators' clothing ;

k) the need for unrestricted work-movements, and the need for space when using foreseeable tools.

In accordance with the values mentioned in EN 547-1 and EN 547-3 standards, unless exceptional circumstances
exist the minimum headroom over working platforms and walkways shall be 2100 mm.

NOTE 1 When justified by the risk assessment and restrictions due to the machinery or environment, the clear height may be
reduced to no less than 1900 mm if:

— the working platform or walkway is used only occasionally, or

— the reduction is made only for a short distance.

Unless there are exceptional circumstances, the clear width of a walkway shall be minimum 600 mm but preferably
800 mm. When the walkway is usually subject to passage or crossing of several persons simultaneously, the width
shall be increased to 1000 mm. The width of the walkway, when designated as an escape way shall meet the
requirements of appropriate regulations.

NOTE 2 When justified by the risk assessment and restrictions due to the machinery or environment, the free width may be
reduced to no less than 500 mm if:

the working platform or walkway is used only occasionally, and

the reduction is made only for a short distance.

If there are isolated obstacles on a wall or under a ceiling that restrict the required width or height, guarding shall be
provided. Moreover, safety measures, e.g. padding, shall be fitted to prevent injuries. Warning signs should also be
considered.

4.2.3 Facilities or equipment

Guard-rails in accordance with EN ISO 14122-3 shall be provided if there is a risk of falling from walkways or
working platforms from a height of 500 mm or more.

Guard-rails are also required at places where there is a risk of sinking or collapsing (e.g. walkway to access to an
extraction machine on a roof).

Appropriate facilities shall be provided for handling heavy objects without rolling or placing them on working
platforms.

4.2.4 Floorings

4.2.4.1 Hazards due to stagnation and/or accumulation of liquid

Floorings shall be designed such that any liquids spilled on them are drained away. If this requirement is not
possible to fulfil for some special reasons, slipping and other hazards caused by the liquid shall be prevented or
minimized in some other suitable way.
 Page 9
EN ISO 14122-2:2001

4.2.4.2 Hazards due to accumulated substances

Floorings shall be made in such a way that neither dirt, snow, ice, etc. nor other substances may accumulate.
Therefore, permeable floorings such as gratings or cold formed planks are an advantage. If this is not possible and
permeable floorings are not used, facilities for removing the accumulated substances shall be provided where
necessary.

4.2.4.3 Trip hazards

To avoid trip hazards, the greatest difference between the tops of neighbouring flooring surfaces shall not exceed
4 mm in height.

4.2.4.4 Hazards generated by falling objects

a) Flooring

Generally, the risk assessment effects the choice of open floorings to working platforms or walkways:

the flooring of a working platform or walkway shall only have such maximum openings that a ball with a
diameter of 35 mm cannot fall through;

floorings above a place where people are working, as opposed to occasional passage, shall have such
maximum openings that a ball with a diameter of 20 mm cannot fall through unless the same safety is
guaranteed by other suitable means.

In cases where the risk assessment concludes that hazards caused by objects or other materials falling or
passing through the flooring are more significant than the slipping, falling, etc. hazards, the flooring shall have
no opening.

b) Joints

Between the edges of floorings and adjacent construction elements or opening edges required to suit elements
fitted in the openings e.g. piping, bins or supports, a toe plate is necessary if the distance between flooring and
element exceeds 30 mm.

4.2.4.5 Falling through flooring hazard

If flooring is made of detachable elements, i.e. removable, e.g. where required for maintenance of auxiliary
equipment mounted below flooring:

— any hazardous movement of these elements shall be prevented e.g. by fasteners;

— it shall be possible to inspect fixings in order to detect any corrosion or any hazardous loosening or change of
position of clamps.
Page 10
EN ISO 14122-2:2001

4.2.4.6 Slip hazards

Floorings shall have a surface finish which is designed to reduce the risk of slipping. Whilst waiting for the
European standards on enhanced slip resistance, see informative annex A.

4.2.5 Design loads

The schedule of specifications for the working platforms and walkways shall state the load for which it is designed.

The minimum operating loads to take into account for the landing, walkways and working platforms are:
2
— 2 kN/m under distributed load for the structure;

— 1,5 kN concentrated load applied in the most unfavourable position over a concentrated load area
of 200 mm x 200 mm for the flooring.
th
When loaded with the design load, the deflection of the flooring shall not exceed 1/200 of the span and the
difference between the loaded and a neighbouring unloaded flooring shall not exceed 4 mm in height.

The safe strength design of the walkways and working platforms shall be verified either by calculation or by tests.

5 Assembly instructions
All information on the proper assembly shall be contained in the assembly instructions. In particular, information on
the method of fixing shall be included.
 Page 11
EN ISO 14122-2:2001

Annex A
(informative)

Different methods of determining levels of slip-resistance

No European Standards exist for the moment, but in the meantime, any of the following national documents are
available for consultation:

France

Exigences pour une norme de mesure de la glissance des sols – Étude documentaire et discussion - ND 1987-
159-95 – INRS

Sols anti-dérapants – Critère d’évaluation de la résistance au glissement – Application aux sols des industries de
l’alimentation - ND 1853-145-91

Normalisation de la glissance des sols et des chaussures - ND 1936-152-93

Glissance des sols et coefficients de frottement - Cahier 2484 (avril 1991) - CSTB

Germany

Merkblatt für Fußböden in Arbeitsräumen und Arbeitsbereichen mit Rutschgefahr - ZH 1/571 - (Oktober 1993) -
HVBG.

United Kingdom

BS 7188:1998 - Impact absorbing playground surfacing Performance requirements and test methods - - Clause 5
"Slip resistance"

BS 8204-3 : 1993 - In-situ floorings Part 3. Code of practice for polymer modified cementitious wearing surfaces
Annex C "Determination of slip resistance value SRV".
Page 12
EN ISO 14122-2:2001

Annex ZA
(informative)
Relationship of this European standard with EC Directives

This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association and supports essential requirements of EC Directive(s)

Machinery Directive 98/37/EC, amended by Directive 98/79/EC,

in particular clause 1.6.2 "Access to operating position and servicing points" and 1.5.15 "Risk of slipping,
tripping or falling" of the essential safety requirements of its annex I

Compliance with this document provides one means of conforming with the specific essential requirements of the
Directive concerned and associated EFTA regulations.

WARNING : Other requirements and other EC Directives may be applicable to the product(s) falling within the
scope of this document.
 Page 13
EN ISO 14122-2:2001

Bibliography

In compiling this standard, the following have been taken into account :

EN 131-2:19931 Ladders — Requirements, Tests, Markings

EN 349 (ISO 13854) Safety of machinery — Minimum gaps to avoid crushing of parts of the human body

EN 353-1 Personal protective equipment against falls from a height — Guided type fall arresters on a rigid
anchorage line

EN 364 Personal protective equipment against falls from a height — Test methods

EN 795 Protection against falls from a height — Anchorage devices — Requirements and testing

EN 811 (ISO 13853) Safety of machinery — Safety distances to prevent danger zones being reached by the lower
limbs

EN 1050 (ISO 14121) Safety of machinery — Principles for risk assessment

prEN ISO 14122-4:1996 Safety of machinery — Permanent means of access to machinery — Part 4 : Fixed
ladders

1 Under revision.
BS EN ISO
14122-2:2001
BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.

Revisions

British Standards are updated by amendment or revision. Users of

British Standards should make sure that they possess the latest amendments or
editions.

It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: 020 8996 9000. Fax: 020 8996 7400.

BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.

Buying standards

Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
Standards are also available from the BSI website at http://www.bsi-global.com.

In response to orders for international standards, it is BSI policy to supply the

BSI implementation of those that have been published as British Standards,
unless otherwise requested.

Information on standards

BSI provides a wide range of information on national, European and

international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: 020 8996 7111. Fax: 020 8996 7048.

Subscribing members of BSI are kept up to date with standards developments

and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is
available on the BSI website at http://www.bsi-global.com.

Copyright

Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.

This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
written permission of BSI must be obtained.

If permission is granted, the terms may include royalty payments or a licensing

agreement. Details and advice can be obtained from the Copyright Manager.
BSI Tel: 020 8996 7070.
389 Chiswick High Road
London
W4 4AL