ITEM No.

Description
A SECTION A - EARTHWORK
A1 Clearing grass and removal of rubbish upto a distance of 50 m outside the
periphery of the area.
A2
Felling trees of girth(measured at a height of 1.0 m. Above ground level)
including cutting of trunks and branches removing the roots stacking the
serviceable material and disposal of unserviceable material for all leads: a)
Beyond 30 cm and upto 60 cm girth.
A3
Earthwork in surface excavation not exceeding 30 cm depth(but exceeding
1.5 m width as well as 10 sq.m on plan) including disposal of excavated
earth beyond work site for all leads lift disposed earth to be levelled and
neatly dressed in: a) Ordinary soil

A4

Earth work in excavation  in all types of stratas comprising of any type of

materials such as soil, silt clay, sand , gravel, murrum of all types of
conglomerates, laterite rock, soft rock, ordinary rock disintegrated rock
fissured/ shattered rock, decomposed rocks weathered rock, bituminous
road layers and all such other materials either in full or part as the case
may be adopting any method / - by mechanical means (hydraulic
excavator) /manual means over areas (exceeding 30 cm in depth , 1.5m in
width as well as 10sqm on plan) including disposal of excavated Earth for
all leads and lift disposed Earth to be leveled and neatly dressed including
pumping and bailing out water, providing barricading , danger lighting
gurading as directed in combination of all kinds of soil and all types of
ordinary rock including all types of laterite rock.

A5
Earthwork in excavation by mechanical means (hydraulic
excavator)/manual means in foundation pipeline trenches drain (not
exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides
and ramming of bottoms, lift upto 1.5 m including getting out the
excavated soil and disposal of surplus excavated soil as directed within a
lead of 50 m.: (b) All types of Ordinary rock including all types of laterite
rock, blasting prohibited

A6
Refilling the pipeline/foundation trenches plinth sides, foundation etc.
with available excavated earth in layers not exceeding 20 cm depth
consolidating each layer ramming and watering lead upto 50 M and all lifts
and disposal of surplus earth as directed by Engineer in Charge.

A7 Supplying and filling in plinth under floors, trenches including watering

ramming consolidating, dressing, complete.: b) Moorum
A8
Clearing jungle including up rooting of rank vegetation grass bush wood
trees and sapling of girth upto 30 cm. measured at a height of 1 m above
ground level & removal of rubbish upto a distance of 50 mt. outside the
periphery of the area cleared. (if however, only grass is met with the area
will be measured and paid for under item A1).

SUB TOTAL A
B SECTION B - MASONARY WORK
B1 Half brick masonry in cement mortar 1:4 (1 cement :4 coarse, sand) with
bricks of class designation 40 kg/ sq. cm upto floor five level. (b) upto floor
five level.
B2 Rubble packing with available hard laterite stone under floors including
watering ramming and consolidating etc. in pipeline trenches and other
foundations complete.
B3 Rubble packing with hard laterite stone under floors including watering
ramming and consolidating etc.in pipeline trenches and other foundations
complete.
B4
Laterite masonry in neatly dressed stones of size as specified in cement
mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

B5 Exposed decorative laterite masonry using Patradevi stone of size as

specified and laid as directed by architect in cement mortar 1:4 (1 cement :
4 coarse sand)
B6 Providing & constructing laterite masonary in neatly dressed stones for 23
cms masonary walls in c.m 1:4 (1 cement : 4 coarse sand) in super
structure from floor I upto floor V level.
SUB TOTAL B
C SECTION C - PLAIN CONCRETE WORK
C1
Providing and laying in position cement concrete 1:2:4 (1 cement : 2
coarse sand: 4 graded granitic or basaltic stone aggregate 40 m nominal
size) excluding cost of centering, shuttering and finishing : (a) All works
upto plinth level.
C2
Providing and laying upto floor five level cement concrete 1:2:4 (1 cement:
2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm
nominal size) including smooth finishing to exposed surfaces, with cement
mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc.
(c ) Small lintels not exceeding 1.5 m clear span, including coping and the
like requiring form work to the suspended portions.
C3
Providing and laying upto floor five level cement concrete 1:2:4 (1 cement:
2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm
nominal size) including smooth finishing to exposed surfaces, with cement
mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc.
(d) Moulding as in cornices, window sills etc. exceeding 15 cm in girth.

C4
Making plinth protection 50mm thick of Cement Concrete 1:3:6 (1cement :
6 graded stone aggregate 20mm nominal size) over 75mm bed of dry
laterite aggregate 40mm nominal size well rammed and consolidated and
grouted with fine sand including finishing the top smooth.

SUB TOTAL C
D SECTION D - REINFORCED CEMENT CONCRETE WORK
D1

Providing and laying in position machine batched concrete (BMC), machine

mixed and machine vibrated design mix cement concrete of specified grade
for reinforced cement concrete work including pumping of concrete to the
site of laying but excluding the cost of centering , shuttering, finishing and
reinforcement including admixtures in recommended proportions as per
IS 9103 to accelerate, retard setting of concrete, improve workability
without impairing the strength and durability as per the direction of the
Engineer-in-charge. M25 grade of reinforced cement conrete by using
410kg of cement per cu.m. of concrete. All works upto floor V level.

D2 Centering & shuttering including Strutting, Propping & removal of forms

for: (i) Foundations, Footings, Bases for columns
D3
Centering & shuttering including Strutting, Propping & removal of forms
for: (ii)Vertical surfaces such as retaining walls, return walls, Partitions,
walls (any thickness) including attached Pilasters, Buttresses, Plinth and
string courses, Fillets and the like.
D4 Centering & shuttering including Strutting, Propping & removal of forms
for: (iii) Columns, Piers, Pillars, Abutments, Posts and struts (square
rectangle polygon in plan).
D5
Centering & shuttering including Strutting, Propping & removal of forms
for: (iv)Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders,
Bressumers and Lintels plinth beams not exceeding 1m in depth.

D6
Centering & shuttering including Strutting, Propping & removal of forms
for: (xiii) Suspended floors, roofs landings, shelves & their supports.
D7
Centering & shuttering including Strutting, Propping & removal of forms
for sloping or battering surface (slabs, beams, louvers, etc) including
folded plates: (iii) Columns, Pillars, Posts & struts (circular or curved in
plan).
D8 Centering & shuttering including Strutting, Propping & removal of forms
for sloping or battering surface (slabs, beams, louvers, etc) including
folded plates: (iv) Cornices & Mouldings
D9
Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel
Ltd.) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S.
1786 of 1986) including bending, binding & placing in position in all the
floors along with the factory made precast concrete cover blocks of
specified sizes whose compressive strength is not less than that of
surrounding concrete in the structural member.

D10

Supplying and fixing of Precast RCC slabs(factory made,the factory should

be ISO certified and registered under Dirctorate of Industries, Govt. of
India) at site in concrete Grade of M-25 with 20 mm nominal size Granitic
or basaltic aggregate, consolidated by means of mechanical platform,
vibration etc. with lifting hooks of M.s. 10mm bars and PVC cups including
cost of reincforcement, Certificate from manufacturer shall be produced
indicating grade of concrete and minimum content of steel in the product
along with 5 year free replacement warranty in case of breakage complete
and as directed by Engineer -in -charge.: (a) Size 900 x 400 x 150 mm with
steel reinforcement not less than 7 kg per unit -30 T capacity.

SUB TOTAL D
E SECTION E - WOOD WORK
E1 Providing woodwork in frames of doors, windows, clerestory windows
trusses & other frames wrought framed and fixed in positon.: Second class
matti wood.
E2
Providing and fixing 35 mm thick panelled glazed or panelled and glazed
shutters in second class Indian teak wood for doors, windows and
clerestory window with stainless steel butt hinges with necessary screws.

E3
Providing & fixing flush door shutters decoration type core of block board
construction with frame of first class hard wood and well matched first
class Indian teak ply veneering with vertical grains and cross bands and
face veneers on both faces of shutters.: 35mm thick including stainless
steel butt hinges with necessary screws.
 E4 Providing and fixing first class Indian teak wood moulded beading to door
and window frames with iron screws, plugs and priming coat on
unexposed surfaces etc.: 50 x 12 mm
E5
Providing flat iron hold fast 40 cms including fixing to frame with 10mm
dia bolts, nuts and wooden plugs and embedded in cement concrete block
30x10x15 cms 1:3:6 mix ( 1 Cement : 3 Coarse Sand :6 Stone aggregates
20mm nominal size).: 40 x 3 mm flat iron hold fast 15cm long

E6 Providing and fixing M.S. grill of required pattern in wooden frames of

Windows etc. with M.S. flats square or round bars with round headed bolts
and nuts or by by screws.: Ornamental grill.
E7 Providing and fixing seamless tower bolts 254mm x 10mm rod 8" in Grade
SS - 304 SSM of approved make with necessary Stainless steel screws etc.
complete .
E8 Providing and fixing Stainless steel D type handles with necessary screws
etc complete a) L 300mm/325mm x 22 to 25mm dia
E9 Providing and fixing stainless steel door latch with necessary screws etc
complete.: 250 x 16 x 5 mm
E10
Providing and fixing floor mounted door stopper in Stainless steel Grade SS
- 304, SSM and complete with rubber cushions and Stainless steel screws
etc.of approved make and quality to suit shutter thickness .

E11

FRP (Fiber Reinforced Polymer) Frames with Wood Finish Manufacture,

Supply and Installation (with anchor fastener) of EPEE or equivalent Goan
make FRP (Fiber Reinforced Polymer) Frame of cross section as per
options below with right angle joint and FRP (Fiber Reinforced Polymer)
laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber
(matt) and unsaturated polyester resin with viscosity range of 400/450
centipoises per second (cps). The core of frame would be filled with
seasoned wood as infill material. The slot of frame for door resting will be
of suitable width so as to take specified thickness door. The frame will be
water proof as well as mild acid/ alkali resistant manufactured in an ISO
9001- 2008 certified company.

Specified Cross Section : d) 5” x 2 ½ “

 E12

Wood Finish Foarm Core FRP(Fibre Reinforced Polymer)Door Shutter

Manufacture, Supply &Installation (including accessories as mentioned
below) of EPEE or equivalent Goan make FRP (Fibre Reinforced
Polymer)door shutter of specified thickness as per options below by using
tray system,with seasoned hard wood, moisture less than 17%, wood
styles for Top rail &lock rails ,FRP (Fibre Reinforced Polymer) laminate
made up of 450 grams per sq.mts (gsm) chop strand matt & unsaturated
polyester resin with viscosity range of 400/450 centipoises per second
(cps) along with UV Resistant resin to give the clear wooden texture on the
door. The core of shutter will be filled as specicied (Expanded Polystyrene
Foam/ Polyurethane Foam (EPS/PU) Foam). the shutter to be water-proof
as well as mild acid/alkali resistant manufactured using RV TIFAC (R V
Engineering College,Bangalore & Technology Information Forecasting &
Assessment Council) Technology in line with IS 13034 1990 test Standard
in an ISO 9001-2008 certified factory.

Accessories:
i) S. S. Hinges 4” - 3 No
ii) S. S. Latch - 1 No
iii) Tower Bolt 5” - 2 Nos
iv) Handle 5” - 2 Nos
Shutter thickness: 35 mm
E13
Providing and Fixing of Sunder Patti with WPC Board including fixtures as
per design/decorative pattern given by Engineer incharge.

E14
Providing and fixing Aldrop 250 x 16mm of Stainless steel 304 grade, SSM
of approved make with necessary stainless steel screws, stainless steel
fittings, etc. complete as per directions of the engineer.

SUB TOTAL E
F SECTION F - STEEL AND ALUMINIUM WORK

Steel work in single sections (SAIL, TATA. VIZAG & using electrodes of
F1 Ador or ES4B or Deh Secheron make only) including cutting, hoisting fixing
in position and applying a priming coat of red lead paint.

In R.S. joists, channels, angles, tees

Steel work in single sections (SAIL, TATA. VIZAG & using electrodes of
F2 Ador or ES4B or Deh Secheron make only) including cutting, hoisting fixing
in position and applying a priming coat of red lead paint.

In flats of all sizes

 Steel work in built up tubular (round, square or rectangular hollow tubes
etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section
(RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural
F3 Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including
cutting, hoisting, fixing in position and applying a priming coat of approved
steel primer, including welding and bolted with special shaped washers
etc. complete.

Providing and fixing in position railing in balconies, verandah, staircase,

ramps with steel tubular sections of specified sizes and design including
F4 making necessary holdfast fixtures embedded in concrete as required for
the work including bending handrail pipe to proper shape. (measurement
will be made along running length of the hand rail)

Providing and fixing anodized aluminium shutters in accordance with the

specification annexed with Goa schedule of Rates (2004) Vol & II including
all taxes, transportation, scaffolding and handling etc. complete as per
F5 direction of the Engineer-in-charge: windows with two sliding shutters
using 18 mm series shutters section including powder coating with pure
polyster powder of shade of required colour on aluminium section. With
Plain glass.

Providing and fixing powder coated anodized aluminum shutters with

pure polyester powder of shade of required colour in accordance with the
F6 specification annexed with Goa schedule of Rates (2004) Vole & II
including all taxes, transportation, scaffolding and handling etc. complete
as per direction of the Engineer-in-charge: Adjustable louvered windows.

SUB TOTAL F
G SECTION G - FLOORING AND FLOOR FINISHES
G1
Kotah stone slab flooring over 20 mm (average) thick base of cement
mortar 1:4 (1 cement : 4 coarse sand) laid over & jointed with grey cement
slurry mixed with pigment to match the shade of the slab including
rubbing & polishing complete. : 20 mm thick.
G2
Providing and laying crazy paving (as per design shown in the drawing or
as directed by the engineer-in- charge) with approved quality shahabad
tile 20 mm thickness (unpolished) of specified sizes laid on 20 mm thick
(average) bed of cement mortar 1:5 (1 cement : 5 coarse sand) as directed
completed.
G3
Providing and fixing kota stone tread tiles 35mm thick in single piece with
rounded of nosing antiskid groove laid on and including 20mm (average )
thk bed of cement slurry including pointing with pigmented cement slurry
to match the shade of the slab, cleaning etc. complete.
 G4
Supplying and fixing Pre-cast cement concrete kerb-stones(factory
made,the factory should be ISO certified and registered under Dirctorate of
Industries, Govt. of India) of M-20 with 20 mm nominal size
granitic/basaltic aggregate properly consolidated by mechanical plat-form
and vibrators with smooth finish including fixing at site complete as per
specification.: Size 60 cm L x45 cm H x 15 cm THK.

G5
Rounding of edges of marble/ Granite / Kotah slab to semi circular slope
G6
Providing and laying jet black mirror polish granite flooring and dado over
20mm thick base of cement mortar 1:4 laid over and jointed with cement
slurry including rubbing complete Granitic slab (jet blck with mirror
polish) 20 mm thick add q0% wastage 1.00.
G7

Providing 18 to 20mm thick wash-basin/kitchen/other platform counters

of machine cut, prepolished Granite stone of approved shape, quality and
colour including making necessary grooves in the wall and fixing with
cement mortar as per drawing , over 30 to 35mm thick cuddapah base,
vertical frames , facia patti, cutting holes of required sizes in appropriate
places to receive sink, basin, pipes etc., fixing in the cement mortar 1:3,
including moulding with edge polishing, curing and cleaning, with M.S.
angle supports finished with one coat of zinc chromate primer & 3 coats of
synthetic enamel paint of approved shade & make, etc. complete as per
detail drawing and as directed/ approved by Engineer-In-Charge. ( N.B. :
plan area to be measure for the payment )

G8
Providing 25 mm thick cuddapah slabs machine cut and polished on either
side in partitions including making necessary grooves in the wall and fixing
with cement mortar, complete as directed by the engineer-in-charge.

G9 Providing and fixing 20mm thick cuddapah in shelves complete

G10
Providing and fixing coloured ceramic tiles of 8" x 12" size and 6 mm thick
in skirting and dados on 12 mm thick cement plaster 1:3 (1 cement : 3
coarse sand) and jointed with cement slurry complete.

G11
Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of
Johnson, Somany, Kajaria (thickness to be specified by the manufacturer)
of 1st quality conforming to IS:15622 of approved make in shades as
specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse
sand) including pointing the joints with white cement and matching
pigment etc., complete.: Dark Shades
G12
Providing and laying scratch resistant floor tiles in different sizes of
Johnson, Somany, Kajaria (thickness to be specified by the manufacturer)
with water absorption less than 0.08% and conforming to IS:15622 of
approved make in colours and shades as specified laid on 20 mm thick
cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints
with white cement and matching pigment etc., complete.: 600x 600 mm
Dark Shades

G13
Providing and fixing Scratch resistant ceramic tiles in different sizes
(thickness to be specified by manufacturer), with water absorption less
than 0.08 % and conforming to I.S. 15622, of approved make, in all colours
& shade, in skirting, riser of steps and dados, jointing with grey cement
slurry @3.3 kg per sqm, including pointing/grouting in white cement
mixed with pigment of matching shade complete. : 600 x 600 mm - Dark
Shades

G14
Providing and and laying vitrified unglazed porcelain tactile floor tiles in
different sizes of Johnson, Somany, Kajaria (thickness to be specified by the
manufacturer) and conforming to IS:15622 of approved make in colours
and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement :
4 Coarse sand) including grouting the joints with white cement and
matching pigment etc., complete.: 300x300mm linear

G15
Providing and and laying vitrified unglazed porcelain tactile floor tiles in
different sizes of Johnson, Somany, Kajaria (thickness to be specified by the
manufacturer) and conforming to IS:15622 of approved make in colours
and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement :
4 Coarse sand) including grouting the joints with white cement and
matching pigment etc., complete.: 300x300mm buttons

G16
Providing and fixing 18mm thick Granite stone to urinal partitions both
sides pre polished, edges full round moulded and polished fixed by cutting
a chase of appropriate width with chase cutter and embedding the stone in
chase with cement concrete ( 1:2:4 ) including all accessories, hardwares
etc. complete as per design drawing

SUB TOTAL G
H SECTION H - ROOFING AND CEILING WORKS
H1 Providing and laying 1st class mangalore tile roof covering over MS
battens including screws, nails etc. but excluding rafters.
H2
Providing and fixing colour coated galvalume roofing sheets of 0.5mm
thickness including all the accessories (TATA make) but excluding the cost
of purlins, rafters, trusses, flashings etc. complete as per the directions of
the Engineer in charge.
H3

Providing & fixing in position Galvalume/Zincalume flashings, cappings,

ridges, gutters upto 600mm/610mm girth and min 3.00m in length (cold
Rolled Steel 550 MPa yeild Stress ASTM A 446 Grade E) with hot-dip
metallic coating of aluminium-zinc alloy(AZ 150 galvalume) (150 gms/sqm
total of both sides with Al-Zn Composition= 55% & 43.5% resp. & 1.5% Si
conforming to ASTM 792/ AS 1397) 0.45 mm base metal thickness and
0.50mm total coated thickness, factory cut at all heights for roof, side &
gable cladding complete in all respects with AZ 150 GSM SMP color Coated
(20mic exterior coat of Silicon Modified Polyester paint system over 5 mic
primer and 5 mic polyester back coat over 5 mic primer) incl. fixing to
purlins with no 12x14x55mm mechanically galvanised hex head self
drilling screws of the best quality as per AS-3566 class 3-4 approved,
which should be compatible to be used with sheets. with integral washers
and EPDM seals etc. Silicon sealant non-hardening neutral cure type shall
be applied at all end laps, complete as directed.

SUB TOTAL H
I SECTION I - PLASTERING AND FINISHING WORKS
I1 6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand)
I2 12mm cement plaster 1:4 (1 cement : 4 coarse sand)
I3
18mm cement plaster in two coats under layer 12mm thick cement plaster
1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement
plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

I4 Neat Cement punning and providing and mixing water proofing material
proportionately, recommended by the manufacturers.
I5

Providing and laying integral cement based treatment (Box type) for water
proofing on horizontal surface at all depth below ground level for under
ground structures as directed by Engineer and consisting of : i) Ist layer of
20 mm to 25 mm thick approved and specified rough stone slab over a
25mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed
with water proofing compound conforming to IS:2645 in the
recommended proportion over the leveling course (leveling course to be
paid separately). Joints sealed and grouted with cement slurry mixed with
water proofing compound. ii) 2nd layer of 25 mm thick cement mortar 1:3
(1 cement: 3 coarse sand) mixed with water proofing compound in
recommended proportions. iii) Finishing top with stone aggregate of
10mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly
embedded in the 2nd layer using rough Shahbad/Kotah stone.
 I6

Providing and laying integral cement based treatment (Box type) for water
proofing on the vertical surface by fixing specified stone slab 20 mm to
25 mm thick with cement slurry mixed with water proofing compound
conforming to IS:2645 in recommended proportions with a gap of 20 mm
(minimum) between stone slabs and the receiving surfaces and filling the
gaps with neat cement slurry mixed with water proofing compound and
finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3
coarse sand) 20 mm thick with neat cement punning mixed with water
proofing compound in recommended proportion complete at all levels and
as directed by Engineer using rough Shahbad/Kotah stone.

I7 Applying priming coat with ready mixed primer of approved brand and
manufacture on wood work complete.
I8 Applying priming coat with ready mixed primer of approved brand and
manufacture on steel work.
I9 Painting two or more coats (excluding priming coat ) with superior quality
ready mixed paint for steel work of approved brand and manufacture in all
shades on new work to give a even shade.
I10 Painting two or more coats (excluding priming coat) with superior quality
ready mixed paint for wood work of approved brand & manufacture in all
shades on new work to give an even shade.
I11
Wall painting (two or more coats) with plastic emulsion paint of approved
brand and manufacture on new work to give an even shade (including min
two priming coats and two layers of putty alternatively).

I12
Painting three or more coats with acryllic exterior paint of approved brand
and manufacture (such as weather shield,APEX) including applying one
coat of cement primer and one coat of surface treatment etc. complete.

I13
Providing and applying white cement based putty of average thickness
1.00mm of approved brand and manufacturer, over the plastered wall
surface to prepare the surface even and smooth complete.

I14 Melamine polishing on wood work (one or more coat).: Matt

I15
Applying breathable, non-reactive, antifungal, and water repellant Silane/
Siloxane chemical as approved by Archaeological Survey of India/
Engineer, of approved brand and manufacture, diluted with solvent
mineral Turpentine oil in the ratio of 1:12 (One part of approved
chemical :12 Part of Turpentine oil), on the exposed laterite masonry
surface with two or more coats to give uniform application of chemical on
the surface, all complete as per direction of Engineer. (The rate is inclusive
of all materials & labours).
 SUB TOTAL I
J SECTION J - DISMANTALING AND DEMOLISHING WORKS
J1 Demolishing laterite stone masonry in cement mortar including stacking of
serviceable material & disposal of unserviceable material within 50 mts.
lead.
J2
Dismantling wood work of sectional area 40 sq.cm. and above wrought
framed and fixed in frames, other frames and trusses including stacking of
material within 50 mts. lead (span upto 10 mtrs.)

J3 Dismantling tiled roofing (Mangalore or pot or country tiles) with battens

etc. complete including stacking of serviceable material & disposal of
unserviceable material within 50 mts. lead.
SUB TOTAL J
K
SECTION K - WATER SUPPLY, SEWERAGE AND SANITATION WORKS
K1
Providing and fixing white vitreous china pedestal type (European type)
water closet with seat and lid, with C.I. brass hinges and rubber fittings 15
lts white vitreous china low level flushing cistern with fittings as brackets
40 mm white porcelain 3enameled flush bad, 25 mm overflow pipe with
specials and mosquito proof coupling of approved municipal design
complete, including cutting and making good the walls and floors where
required. : E.W.C. pan with white plastic seat and lid

K2
Providing and fixing white vitreous china flat back or wall corner type
lipped front urinal basin of 430 x 260 x 350 mm and 340 x 430 x 265 mm
sizes respectively with pvc automatic flushing cistern with fittings, R.S. or
C.I. brackets, standard size galvanised steel flush pipe and spreaders with
brass unions & G.I. clamps complete, including painting of cister and
fittings, cutting and making good the walls and floors where required.:
One urinal basin with 5 litres p.v.c. automatic flushing cistern

K3
Providing and fixing vitreous china wash basin with RS or C.I. brackets
painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber
plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass
trap and union complete, including cutting and making good the walls
where required.: Flat back wash basin size 630x450mm with a pair of
15mm C.P. brass pillar taps.

K4 Providing and fixing C.P. bras or M. I. Trap for wash basin and sinks: 40
mm dia
K5
Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass
(of approved quality) complete with 6 mm thick asbestos sheet ground
fixed to wooden cleats with C. P. brass screws and washers.
 K6
Providing and fixing c.p. brass towel rail complete with C.P. brass brackets
fixed to wooden cleats with C.P. Brass screws: 600 X20 mm size

K7 Providing and fixing soap dish chromium plated with brackets fixed to
wooden cleats with CP Brass screws
K8 Providing and fixing brass full way valve (heavy) duty with wheel of
approved quality : 15 mm nominal bore
K9 Providing and fixing brass full way valve (heavy) duty with wheel of
approved quality : 20 mm nominal bore
K10 Making connection of G. I. Distribution branch with G. I. Main 50 mm to
80 mm nominal bore by providing and fixing tee including treading the
pipe etc. complete
K11
Proving and fixing white vitreous china water closet squatting pan (Indian
type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10
litres high level P.V.C. flushing cister (of approved make) with fittings, rack
bolts 32 mm diameter P.V.C telescopic flush pipe with fit tings and clamps
25mm P.V.C. over flow pipe with specials & mosquito proof coupling of
approved municipal design and nylon pull complete cutting and making
good the walls and floors where required.: Orissa pattern W.C. pan

K12 Providing and fixing ball valve (brass) of approved quality: (a) High
pressure with P.V.C. float - (1) 15 mm nominal bore
K13
Providing and placing on terrace roof of floor two (1st flor roof single piece
rotational moulded polythene water storage tank having I S I mark and
conforming to I S 12701; 1996.: 1000 lit. capacity

K14
Providing and fixing square mouth gully trap grade A complete with c. i.
grating brick masonary chamber and water tight factory made concrete
cover with frame (medium duty) of 300 X 300 mm size of Astra make or
Equivalent as per standard design:150 X 100 mm size- P or S type
K15

Constructing brick masonry manhole or inspection chamber with

second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top
slab with 1:2:4 mix (1 cement: 2 coarse sand;4 graded stone aggregate
20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse
sand :4 graded stone agrregate 40mm nominal size) inside plastering 12
mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with
a floating coat of neat cemetn and making channels in cement concrete
1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm
nominal size) neatly finished complete as per standard design.: (d) Inside
size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty)
455x610mm internal diameter total weight of cover and frame to be not
less than 38 kg. (weight of cover 23 kg).

K16
Making soak pit. 2.5 m dia 3 m deep with 45x45 cm dry brick honey comb
shaft and S.W. drain pipe 100 mm diameter, 1.8 m long complete filled with
laterite stone aggregate 125 to 180 mm surrounded by laterite stone
aggregate of 40 mm and down gauge as per standard design.

K17 Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage
pipes of approved including lubricant etc. complete (single/double)
socketed:
110 mm
75 mm
K18 Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes
including lubricating etc complete bend with door :
a 100 mm dia
b 75 mm dia
K19 Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R.
pipes including lubricating etc complete, with door :
110 mm dia
75 mm dia
K20 Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R.
pipes including lubricating etc complete, with door :
a 110 mm dia
b 75 mm dia
K21 Providing and fixing double “Y” of rigid PVC (approved make ) for S.W.R.
pipes including lubricating etc complete, without door
a 110 mm dia
b 75 mm dia
K22 Providing and fixing nahani trap of rigid PVC (approved make ) for
S.W.R. pipes including lubricating etc complete, without door :
110mm dia
K23 Providing and fixing R.P.V.C. vent cowl
 75mm dia
K24 Providing and fixing centrifugally cast iron confirming to IS 3989 / 84 soil
waste and vent pipes NECO brand or equivalent.
75 mm dia
K25
Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock
Short Body Jaquar make or equivalent. Confirming to IS 8931;1993.

15mm nominal bore

K26 Providing and fixing NICKEL chrome plated copper alloy Fancy concealed
stop cock with slinding flance 15 mm Jaquar make or equivalent.
Confirming to IS 8931;1993.: (a) 15mm nominal bore
K27 Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE
TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS
8931;1993
K28
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS
13983 including cutting of stone and making good the walls wherever
required. Kitchen sink without drain board. with coupling & all accessories
complete with choke stop strainer, Plain type having flat borders for
correct sandwithing between the platform top and bottom slabs
complete. : Overall size 610mmx460mm (24"x18") bowl size
560mmx410mmx215mm (22"x16"x81/2") Glossy. 1.0mm thk,

K29
Providing and fixing Hand Shower (Health Faucet) with 8mm dia,
ABS/brass body with double lock 1.00m long Flexible tube (Brass plated
stainles steel flexible hose) and wall hook of approved quality confirming
to IS standards.
K30
Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes
confirming to IS:15778, having thermal stability for hot and cold water
supply including all CPVC plain and brass threaded fittings including fixing
the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and
fittings with one step CPVC solvent cement and testing of joints complete
as per direction of the Engineer-in-charge. Concealed work (medium
duty SDR 13.5 pipe) including cutting chases and making good the
walls etc. : 15 mm dia nominal outer dia pipes.
K31
Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes
confirming to IS:15778, having thermal stability for hot and cold water
supply including all CPVC plain and brass threaded fittings including fixing
the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and
fittings with one step CPVC solvent cement and testing of joints complete
as per direction of the Engineer-in-charge. Concealed work (medium
duty SDR 13.5 pipe) including cutting chases and making good the
walls etc. : (b) 20 mm dia nominal outer dia pipes.

K32
Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO
14001, including all UPVC plain & brass threaded fittings, including
jointing of pipes & fittings with one step UPVC solvent cement, trenching,
refilling & testing of joints complete as per direction of Engineer. External
work. :
SCH-40(blue)/(white)
20 mm nominal outer dia pipes.
25 mm nominal outer dia pipes.
K33
Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes
confirming to IS: 15778 having thermal stability for hot and cold water
supply includng all CPVC plain and brass threaded fittings CPVC solvent
cement, trenching, refilling and testing of joints complete as per direction
of the Engineer in charge. : (External work (heavy duty SDR 11 pipe). :
(b) 20 mm nominal outer dia pipes.

K34
Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes
confirming to IS: 15778 having thermal stability for hot and cold water
supply includng all CPVC plain and brass threaded fittings CPVC solvent
cement, trenching, refilling and testing of joints complete as per direction
of the Engineer in charge.(External work (heavy duty SDR 11 pipe). : 25
mm nominal outer dia pipes.

K35 Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way
Bib Cock with single knob and wall flange conforming to IS 8931:1993
15mm nominal bore
K36
Providing and fixing NICKEL chrome plated copper alloy Fancy long body
bib cock with wall flance Jaquar make or equivalent. Confirming to IS
8931;1993.: 15mm nominal bore

K37
Providing and fixing NICKEL chrome plated copper alloy Fancy wall mixer
with 115mm long bend pipe for connection to over head shower Jaquar
make or equivalent. Confirming to IS 8931;1993. Wall mixer with 115 mm
long bend pipe for connection to over head shower.
 SUB TOTAL K
L SECTION L - MISCELLANEOUS WORKS
L1
Providing anti – termite treatment to buildings conforming to I.S.S.
6113 part II 1971 (revised) including adopting precautions for health
hazards and safety measures as required therein with the cost of all
materials, chemicals, plants, equipments required for the treatment and
furnishing a guarantee for a minimum period of 10 years from the date of
completion including eradicating any infestation of termite free of cost
during the guaranty period complete. (The payment will be made on plinth
of the building. : Pre construction

L2
Providing and fixing prefabricated compound gate of G.I. pipes 40 – 50
mm dia (medium) with 12mm M.S. square bars of G.I. pipes grill work as
per drawing including providing & fixing locking arrangements, pintals,
hold fast embedded in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4
granitic or basaltic aggreate 20mm nominal size) including applying
priming coat with ready mixed red lead paint and painting 2 or more coats
with superior ready mixed paint of approved brand and manufacture in all
shades as per direction complete.

SUB TOTAL L
M SECTION M - SALVAGE VALUE
M1 Rebate for taking Manglore tiles including carting away, loading, unloading
etc. complete
M2 Rebate for taking all types of wooden items including carting away,
loading, unloading etc. complete
SUB TOTAL M
N SECTION N - ELECTRICAL WORKS
N1
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5
sq.mm FRLS PVC insulated copper conductor single core cable in recessed
PVC conduit(heavy) with modular switch, modular plates, suitable size
modular GI box of specified Category and earthing the point with 1.5
sq.mm FRLS PVC insulated copper conductor single core cable etc. as
required.

Group C -- with Cat B Modular Accessories

N2
Wiring for group controlled light point/ fan point/ exhaust fan point/ call
bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core
cable in recessed PVC conduit(heavy) and earthing the point with 1.5
sq.mm FRLS PVC insulated copper conductor single core cable etc. as
required.
 N3
Supplying and fixing suitable size modular GI box with modular plate and
cover in front on surface or in recess including providing and fixing 3 pin
5/6 A modular socket outlet and 5/ 6 A modular switch connection
painting etc. as required. ( For light point to be used in non residential
buildings)
Cat B
N4
Supplying and fixing suitable size modular GI box with modular plate and
cover in front on surface or in recess including providing and fixing 6 pin
15/16 A and 5/6 A modular socket outlet modular socket outlet and
15/16A modular switch connection painting etc. as required. Cat B

Cat B
N5
Wiring for circuit/ submain wiring alongwith earth wire with the following
sizes of FRLS PVC insulated copper conductor single core cable in the
independent recessed PVC conduit(heavy) of appropriate size as required.

(i) (b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

(ii) (c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)
N6 Supplying and erecting of 48 inch (1200mm sweep) ceiling fan, double ball
bearing type complete with all accessories
Cat B
N7 Supplying and erecting ‘B’ class G.I. pipe / M.S. pipe down rod duly painted
for fan complete erected with PVC three core flexible cable 1 sq. mm
copper PVC wire.
N8 Supply and erecting of 9 inch (225 mm sweep) exhaust fan, 1400 rpm,
complete with all accessories.
(a) Cat A
N9 Supplying and fixing stepped type electronic fan regulator on the existing
modular plate switch box including connections but excluding modular
plate etc. as required
Cat B
N10 Supply and erecting 'J' type Mild Steel fan hook fabricated out of 35 X 6
mm flat strip suitable for rafters complete with coach screws etc as
required.
(c) For 6 inches rafter size
N11 Supplying, installing, testing & commissioning digital (hybrid) type EPABX
of 3 x 8 extensions complete.
N12 Supplying, installing, testing & commissioning push button telephone
instrument desk top/wall mount with caller ID & Speaker unit as per
specification complete.
N13 Supplying, installing, testing & commissioning push button telephone
instrument desk top unit as per specification complete
N14 Supplying and fixing following modular switch/ socket on the existing
modular plate and switch box including connections but excluding
modular plate etc. as required
(i) (m) Telephone socket outlet Cat B
(ii) (n)'TV Antenna socket outlet Cat B
N15
Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated
copper conductor unarmoured telephone cable ITD/DOT approved, with
GI saddles on wall or in the existing surface/recesed steel/PVC conduit
having folowing pair(s), complete as required.

(a) 2 Pair
N16
Supplying and drawing/fixing jelly filled outdoor type armoured telephone
cable with 0.5 sq.mm dia. tinned copper conductor, ITD/DOT approved,
with GI saddles on wal or in the existing surface/recesed steel/PVC
conduit having folowing pair(s), complete as required.

(b) 10 Pair
N17
Supplying, installing, testing and commissioning of Junction Box, ITD/DOT
approved, indoor type with wall mounting/concealed facility having front
door with lock along with aluminium frame for mounting disconnection
type Krone modules, complete cabinet fabricated from 18 SWG CRCA sheet
with powder coating in appropriate manner and suitable for following
capacity of pairs, including Krone makemodules, crimping and
terminations, etc. complete as required.

(a) 10 Pair
N18
Supplying and drawing of Co-axial TV cable of required grade, solid copper
conductor PE insulated, shielded with fine tinned copper braid and
protected with PVC sheath in existing surface/recessed steel/PVC conduit
of appropriate size including connection, etc. complete as required

(c) RG - 11
N19
Supplying and fixing of following sizes of rigid PVC conduit alongwith
accessories in surface(medium)/recess(heavy) including cutting the wall
and making good the same in case of recessed conduit as required.

(a) 20 mm
N20
Supplying and fixing 20 A 240 V SPN industrial type socket outlet with 2
pole and earth metal enclosed plug top alon with 20 A, C series SP MCB in
sheet steel enclosure in surface or in recess with chained metal cover for
the socket outlet and complete with connections testing and
commissioning etc. as required"
Cat B
N21
Supplying and fixing following way TPN sheet steel, double door, Verticle
type MCB distribution board 415 V on surface/ recess complete with
tinned copper busbar neutral busbar earth bar dinnbar detachable gland
plate interconnections phosphotized and powder painted including
earthing etc. as required ( but without
MCB/RCCB/Isolator)interconnection between incomer MCB and busbars
of following ways (but without MCBs as required)

(i) (d) 4 way (8+12), double door, Vertical type, Cat B

(ii) (e) 8 way (8+24), double door, Vertical type, Cat B
(iii) (f) 12 way (8+36), double door, Vertical type, Cat B
N22 Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and
other loads of following poles in the existing MCB DB complete with
connections testing and commissioning etc as required.
(i) (f) SP, Cat B
(ii) (i) TP, Cat B
N23 Supplying and fixing 40 A, C series MCB suitable for lighting and other
loads of following poles in the existing MCB DB complete with connections
testing and commissioning etc as required.
(i) TP, Cat B
N24 Supplying and fixing 63 A, C series MCB suitable for lighting and other
loads of following poles in the existing MCB DB complete with connections
testing and commissioning etc as required.
(i) TP, Cat B
N25 Supplying &erecting 5W-7W, 230V integral type LED Lamp suitable for B-
22/E-27 base.
N26
Supplying & erecting inverter LED batten 20W tube light fitting with
polycarbonate housing, heat sink, integrated HF electronic driver,
Min.2600 mAh Lithium ion Battery with charging time of 8-10 Hours and
backup time of Min. 3 hrs. with minimum 25 % of initial Watts having
luminous efficacy of 100 lumens/watt, CRI>80, CCT of 6500K and
THD<=20% having useful life of minimum25000 hrs, with overheating
protection with 2 years warranty.

N27
Supply, fabrication, Erection, testing and commissioning of LT panel fully
compartmentalised,entry at top/ bottom, floor mounted with frame of
suitable M.S channel dully painted, fabricated of 14/16 swg CRCA sheets
completely derusted, chemically treated and powder coated with shade
suggested by client and having following items as per single line diagram:-

Incomer MCCB of 160A TPN with RYB indication, Digital Multifunction

Meter.
Electronic type three phase energy meter (KWh)-1 No.
100A 4 Pole, Load Break Changeover Switch
200A TPN 50kA Busbars
 6-32A MCB - 8 Nos., 40A MCB - 2 Nos., 63 A MCB - 2 Nos.
N28
Supplying & erecting three phase, 415V, street light control panel upto the
max load of 12 kW, TPN MCB 63A, powder coated CRCA 14 SWG sheet,
outdoor type, having IP54,IK10 protection, suitable rating contactor, three
phase, 24 hrs. astronomical time switch with minimum 5 years battery
back up, auto/manual selector switch, ON/OFF push buttons, indicator
lamps, control wiring, metering device, etc for automatic operation, with
overcurrent, short circuit, earth fault protection on provided iron frame /
CC foundation

N29
Supply of 3 1/2 core armoured PVC insulated, PVC sheathed aluminium
conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part
I) ,IS:7098(Part II) with latest amendments of following size.

(i) 3 1/2 Core 70 sq.mm

(ii) 3 1/2 Core 25 sq.mm
N30
Supply of 4 core armoured PVC insulated, PVC sheathed aluminium
conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part
I) ,IS:7098(Part II) with latest amendments of following size.

4 Core 16 sq.mm
N31
Supply of 4 core armoured PVC insulated, PVC sheathed copper conductor
cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part
I) ,IS:7098(Part II) with latest amendments of following size.

(i) 4corex2.5sqmm
(ii) 4corex4sqmm
N32
Laying of one number PVC insulated and PVC sheathed/XLPE power cable
of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including
excavation in the form of a trench as per Cable Trench Drawing provided
by the Engineer-Incharge,sand cushioning with screened sand bed of
20mm thick , protective covering with bricks placed breadth-wise on top of
cable all over the run( the brick protection shall cover the cable and
project atleast 5 cms over them sides of the cable) and backfilling the
excavated earth without stones or hard material and making the surface
proper with 15 cm crown on the top complete as required.

In all type of soil

N33

Laying of one number PVC insulated and PVC sheathed/XLPE power cable
of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm
direct in ground including excavation in the form of a trench as per Cable
Trench Drawing provided by the Engineer-Incharge,sand cushioning with
screened sand bed of 20mm thick , protective covering with bricks placed
breadth-wise on top of cable all over the run( the brick protection shall
cover the cable and project atleast 5 cms over the sides of the cable) and
backfilling the excavated earth without stones or hard material and
making the surface proper with 15 cm crown on the top complete as
required.

In all type of soil

N34

Laying of one number additional PVC insulated and PVC sheathed/XLPE

power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in
ground in the same trench in one tier horizontal formation including
excavation in the form of a trench as per Cable Trench Drawing provided
by the Engineer-Incharge,sand cushioning with screened sand bed of
20mm thick, protective covering with bricks placed breadth-wise on top of
cable all over the run( the brick protection shall cover the cable and
project atleast 5 cms over the sides of the cable) and backfilling the
excavated earth without stones or hard material and making the surface
proper with 15 cm crown on the top complete as required.

In all type of soil

N35
Laying of one number PVC insulated and PVC sheathed/XLPE power cable
of 1.1 KV grade of size not exceeding 25 sq.mm in the existing
RCC/HUME/STONEWARE Metal pipe, etc. complete as required

N36
Supplying & laying (including excavation) reinforced cement concrete pipe
of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level
and slope including providing and fixing collars in cement mortar 1:2 and
curing etc. complete.
N37
Supplying and making cable end terminations with brass compression
gland and copper lugs for folowing sizes of 3 1/2 Core PVC insulated PVC
sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as
required.
(i) 3 1/2 Core 70 sq.mm
(ii) 3 1/2 Core 25 sq.mm
N38
Supplying and making cable end terminations with brass compression
gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC
sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as
required.
(i) 4 x 2.5 Sq. mm.
 (ii) 4 x 4 Sq. mm.
(iii) 4 x 16 Sq. mm.
N39 Providing and fixing 6 SWG GI wire on surface or in recess for loop
earthing along with existing surface/recessed conduit/submain wiring/
cable as required.
N40 Supplying and erecting Annealed bare copper wire of high purity of
required sizes used for earthing on wall with necessary copper clamps
fixed on wall/cable/conduit with screws complete.
N41

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI
mark,of approved brands, including accessories and providing masonry
enclosure with CI/RCC cover having locking /lifting arrangement and
watering pipe etc. with charcoal or coke and salt) as required as per the
Earthing Drawing provided by the Engineer-Incharge.The scope of work
includes the following: a) Excavation of pit of size 1.0x1.0x 2.0 mtrs(min)
and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per
specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling
the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum
resistivity i/c transportation. e)Masonary chamber with proper
foundation, cover plate and locking arrangement. f) Testing of earth value
with earth megger and certifications of its value. Aluminium tag with
embossed earthing value to be attached to the pipe. g)watering
arrangement(plumbing will be paid seperately).

GI Pipe Earthing (All types of stata)

N42 Extra for using salt and charcoal for pipe earth electrode as required( 65
Kgs of Charcoal and 5 Kgs of Salt).
N43

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including

accessories and providing masonry enclosure with CI/RCC cover having
locking/Lifting arrangement and watering pipe etc. (but without charcoal
or coke and salt) as required as per the Earthing Drawing provided by the
Engineer-Incharge.The scope of work includes the following: a) Excavation
of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil.
b)Watering GI pipe, 20mm, Class B, with funnel as per specs.
c)Charcoal/salt as per specs (paid seperately). d) Refilling the pit of size
1.0x1.0x 3.0mtrs(min) with soft black agriculture soil of minimum
resistivity i/c transportation. e)Masonary chamber with proper
foundation, cover plate and locking arrangement. f) Testing of earth value
with earth megger and certifications of its value. Aluminium tag with
embossed earthing value to be attached to the pipe.g)watering
arrangement(plumbing will be paid seperately).

GI Plate Earthing (All types of stata)

N44 Extra for using salt and charcoal for GI or Copper plate earth electrode as
required96kgs of charcoal and 5kgs of salt)
N45 Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for
coneections etc. as required
N46 Supplying & erecting FRP box of size 150 x 125 x 100 mm, 2.7 mm thick
complete on pole/wall as per specification no. CB-SB
N47
Supplying and erecting integrated LED Bollard Cylindrical/Cubical shaped
800mm 8W IP65 & IK10 class having extrusion aluminium housing with
polycarbonate diffuser, having system lumens output of Min. 800 Lumens,
min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500 K, THD<10%,
p.f.>0.90, operating range of 140-240V, inbuilt surge protection of 20 kV,
Life class of 25,000 Hrs. at L50B50, including driver complete with 2 Year
warranty as per specification No.FG-ODF/FLS2.

N48
Supplying and erecting LED square / circular Max. 25 W down
lighter/Panel Light having pressure die-cast aluminium housing,
polystyrene diffuser having system lumens output of Min. 2750 Lumens,
min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120
deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V,
surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including
driver, having mounting arrangement with board for surface type or spring
loaded mounting clips complete with 3 years warranty

N49
Supplying and erecting bulk head LED fitting max. 10W with high
transitivity diffuser with system lumens output of min. 1100 lumens, min.
efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg.,
THD<10%, p.f. >0.95, operating range of 140-260V, in built surge
protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver,
IP66, IK09 rated on provided PVC Block / wooden board with 3 years
warranty

N50
Supplying and erecting integrated LED flood light fitting Max. 30W IP65 &
IK07 class having pressure die-cast aluminium housing, having system
lumens output of Min. 3000 Lumens, min. efficacy of 100 lumen/W,
CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-
270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50,
including driver with U shaped bracket with 3 Years warranty as per
specification No FG-ODF/FLS2.
N51
Supplying and erecting integrated LED flood light fitting Max. 100W IP65 &
IK07 class having pressure die-cast aluminium housing, having system
lumens output of Min. 12000 Lumens, min. efficacy of 120 lumen/W,
CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-
270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50,
including driver with U shaped bracket with 3 Years warranty as per
specification No FG-ODF/FLS2

N52
Supplying & erecting GI flexible Conduit 50 mm dia. conforming to I.S. with
required number of couplings, bushes, check nuts etc. complete

N53
Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg.
capacity cartridge type conform to IS 2878 /15683 complete erected with
necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in
wall complete.
SUB TOTAL N
GRAND TOTAL IN FIGURES RS.
GRAND TOTAL IN WORDS RS.
" This is a Electronic Submission No Ne
 Unit Qty Rates In Figures Rates In Words

100 sq.m. 31.00 90.00 #NAME?

each 12.00 1200.00 #NAME?

sq.m 1014.00 80.00 #NAME?

Cu.m. 171.00 #NAME?

Cu.m. 654.00 650.00 #NAME?

Cu.m. 406.00 250.00 #NAME?

Cu.m. 99.00 650.00 #NAME?

sq.m 3000.00 10.00 #NAME?

Sq.m. 85.00 #NAME?

cu.m 23.00 #NAME?

cu.m 359.00 #NAME?

cu.m 192.00 #NAME?

cu.m 77.00 #NAME?

cu.m 119.00 #NAME?

cu.m 190.00 #NAME?

cu.m 3.00 #NAME?

cu.m 3.00 #NAME?

sq.m 117.00 #NAME?

cu.m 78.00 #NAME?

sq.m 68.00 #NAME?

sq.m 77.00 #NAME?

sq.m 23.00 #NAME?

sq.m 214.00 #NAME?

sq.m 99.00 #NAME?

sq.m 82.00 #NAME?

sq.m 11.00 #NAME?

kg 8580.00 #NAME?

Each 35.00 #NAME?

Cu.m. 2.00 #NAME?

Sq.m. 29.00 #NAME?

sq.m 20.00 #NAME?

 m 97.00 #NAME?

Each 160.00 #NAME?

Kg 422.00 #NAME?

Each 56.00 #NAME?

Each 68.00 #NAME?

Each 18.00 #NAME?

Each 24.00 #NAME?

m 79.00 #NAME?
 sq.m 21.00 #NAME?

rmt 245.00 #NAME?

Each 18.00 #NAME?

kg 23.00 #NAME?

kg 306.00 #NAME?
 kg 17774.00

#NAME?

rmt. 46.00

#NAME?

Sq.m 13.00

#NAME?

Sq.m 5.00

#NAME?

sq.m 381.00 #NAME?

sq.m. 711.00 #NAME?

sq.m. 27.00 #NAME?

R.M. 550.00 #NAME?

r.m. 37.00 #NAME?

Sq.m. 47.00 #NAME?

sq.m 25.00 #NAME?

sq.m 18.00 #NAME?

sqm. 20.00 #NAME?

sq.m 209.00 #NAME?

sq.m. 64.00 #NAME?

sq.m 240.00 #NAME?

sq.m 13.00 #NAME?

sqm. 5.00 #NAME?

sqm. 2.00 #NAME?

sqm. 4.00 #NAME?

sq.m 853.00 #NAME?

Sqm 687.00 #NAME?

 r.m. 418.00 #NAME?

Sq.m. 56.00 #NAME?

Sq.m. 679.00 #NAME?

Sq.m. 898.00 #NAME?

Sq.m. 83.00 #NAME?

sq.m. 56.00 #NAME?

sqm. 13.00 #NAME?

sq.m 108.00 #NAME?

Sq.m. 46.00 #NAME?

Sq.m. 836.00 #NAME?

Sq.m. 2.00 #NAME?

Sq.m. 526.00 #NAME?

Sq.m. 898.00 #NAME?

Sq.m. 526.00 #NAME?

sq.m 36.00 #NAME?

sq.m 420.00 #NAME?

sq.m 366.00 #NAME?

Cu.m 4.00 #NAME?

sq.m 115.00 #NAME?

each 12.00 #NAME?

Each 5.00 #NAME?

Each 14.00 #NAME?

Each 17.00 #NAME?

Each 14.00 #NAME?

Each 4.00 #NAME?

Each 4.00 #NAME?

each 8.00 #NAME?

each 4.00 #NAME?

Each 1.00 #NAME?

Each 2.00 #NAME?

Each 9.00 #NAME?

Each 8.00 #NAME?

Each 8.00 #NAME?

Each 20.00 #NAME?

Each 4.00 #NAME?

m 120.00 #NAME?
m 170.00 #NAME?

Each 40.00 #NAME?

Each 35.00 #NAME?

Each 10.00 #NAME?

Each 14.00 #NAME?

Each 10.00 #NAME?

Each 10.00 #NAME?

Each 7.00 #NAME?

Each 7.00 #NAME?

Each 25.00 #NAME?

Each 12.00 #NAME?

m 22.00 #NAME?

Each 16.00 #NAME?

Each 13.00 #NAME?

Each 17.00 #NAME?

Each 3.00 #NAME?

Each 14.00 #NAME?

r.m. 250.00 #NAME?

r.m. 250.00 #NAME?

r.m. 250.00 #NAME?

r.m. 250.00 #NAME?

r.m. 230.00 #NAME?

r.m. 230.00 #NAME?

Each 16.00 #NAME?

each 4.00 #NAME?

each 4.00 #NAME?

sq.m 789.00 #NAME?

Sq.m. 15.00 #NAME?

sqm 211.00 #NAME?

Cu.m 4.00 #NAME?

Point 131.00 #NAME?

Point 39.00 #NAME?

 Each 26.00 #NAME?

Each 14.00 #NAME?

Metre 814.00 #NAME?

Metre 320.00 #NAME?

Each 19.00 #NAME?

m 38.00 #NAME?

Each 16.00 #NAME?

Each 19.00 #NAME?

Each 19.00 #NAME?

Job 1.00 #NAME?

Each 1.00 #NAME?

Each 5.00 #NAME?

 Each 6.00 #NAME?
Each 3.00 #NAME?

Metre 91.00 #NAME?

Metre 190.00 #NAME?

Each 5.00 #NAME?

Metre 70.00 #NAME?

Metre 164.00 #NAME?

Each 4.00 #NAME?

Each 3.00 #NAME?
Each 3.00 #NAME?
Each 1.00 #NAME?

Each 93.00 #NAME?

Each 5.00 #NAME?

Each 4.00 #NAME?

Each 1.00 #NAME?

Each 44.00 #NAME?

Each 43.00 #NAME?

No. 1.00 #NAME?

 No 1.00 #NAME?

Meter 110.00 #NAME?

Meter 260.00 #NAME?

Metre 996.00 #NAME?

Metre 502.00 #NAME?

Metre 50.00 #NAME?

Metre 1180.00 #NAME?

Metre 110.00 #NAME?

Metre 589.00 #NAME?

Metre 149.00 #NAME?

Metre 70.00 #NAME?

Each 2.00 #NAME?

Each 4.00 #NAME?

Each 126.00 #NAME?

 Each 10.00 #NAME?
Each 182.00 #NAME?

Metre 1698.00 #NAME?

kg 12.00 #NAME?

Set 10.00 #NAME?

set 10.00 #NAME?

Set 2.00 #NAME?

 Set 2.00 #NAME?

Meter 125.00 #NAME?

each 150.00 #NAME?

Each 103.00 #NAME?

Each 20.00 #NAME?

Each 24.00 #NAME?

Each 12.00 #NAME?

 Each 15.00 #NAME?

m 272.00 #NAME?

Each 6.00 #NAME?

s a Electronic Submission No Need to Signature"

Amount(Rs.)

2790.00

14400.00

81120.00

0.00

425100.00

101500.00

64350.00
 30000.00
719260.00

0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00
0.00
0.00

0.00
0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00
0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00
0.00

0.00
0.00

0.00
0.00

0.00
0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00
0.00
0.00

0.00

0.00

0.00

0.00

0.00

0.00
0.00
0.00
0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00
0.00

0.00

0.00
0.00

0.00
0.00

0.00

0.00

0.00

0.00
0.00

0.00
0.00
0.00

0.00

0.00

0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00

0.00

0.00
 0.00

0.00

0.00
0.00
719260.00
#NAME?