DIY Raised Garden Bed For Under $40

DIY Raised Garden Bed for Under $40
Difficulty
Moderate
Build this DIY raised garden bed in an afternoon for less than $40. This bed uses common construction lumber and
corrugated roofing for a rot-resistant, durable bed that is as easy to use as it is to build.
Page 1 of 16
Tools Materials
Kreg Tools Wood Products
4 Board , 2x4 , 96"

Kreg Pocket-Hole Jig® 720
1 Board , 4x4 , 96"
4 Board , 1x4 , 48"
Other Tools
Hardware & Supplies
Circular Saw (cordless)
1 Kreg 2.5" Pocket Hole Screws (Box)
Miter Saw
1 Kreg 1" Pocket Hole Screws (Box)
Table Saw
1 2.5" Deck Screws (Box)
Tape Measure 1 27" X 8' Corrugated Panel
Clamps
Drill (cordless)
Sawhorse
Page 2 of 16
Cut List & Parts
4 Legs , 4"x4"x16"
8 Cross Braces , 2"x4"x48"
4 Top Plate , 1"x4"x48"
4 Corrugated Panels , 4'x13.5"
Page 3 of 16
Directions
Legs
1 First step is to cut your 4 legs from the 8 foot 4"x4". Each leg should be 16" in length.
Page 4 of 16
Cross Braces
2 Next you need to cut your cross braces from your 8 foot 2"x4"s. You should have 8 boards cut to 48" in length.
Pocket Holes
3 Next you want to add 2 pocket holes to each end of the 8 cross braces, using your Kreg Jig.
Page 5 of 16
Cut Side Panels 1 of 2
4 Next you want to cut 4 side panels from the 27"x8' corrugated panel. To do this, you want to make your first cut across the
panel creating 2 panels that are 27"x4'. These panels are very thin and can be cut using a circular saw.
Page 6 of 16
Cut Side Panels 2 of 2
5 Next you need to take the 2 side panels from the previous step and cut them into 4 panels that are 13.5"x4' in size. After this
step you should have four 13.5"x4' corrugated panels.
Page 7 of 16
Build Sides 1 of 3
6 Next you want to attach 2 of the legs to 1 of the cross braces. The cross brace should be flush to the bottom and side of each
leg. You will be attaching these using 2.5" Kreg Pocket Hole screws.
Page 8 of 16
Build Sides 2 of 3
7 Next you need to attach the top cross brace to the legs from the previous step. This brace will not be flush with the top of
the leg, but will have a slight offset. The distance from the bottom of the bottom brace to the top of the top brace should be
14". Again, use 2.5" Kreg Pocket Hole Screws to attach the brace to the legs.
Page 9 of 16
Build Sides 3 of 3
8 Once the legs are connected with the 2 cross braces, it's time to attach one of the corrugated panels. Place the panel across
the side, leaving approximately 3/8" at the top and bottom. Attach using 1" Kreg Pocket Hole Screws.
Page 10 of 16
Additional Support (Optional)
9 If you will be attaching a top plate to the sides, it is a good idea to add some additional support to attach the 1"x4"x48" cedar
fence slats to. These are attached using exterior deck screws. It helps to clamp the board to the panel before permanently
attaching to prevent slipping.
Page 11 of 16
Connect Sides
10 After building 2 of the sides, you need to connect them with the remaining cross braces. The easiest way to do this is to
stand up the 2 build sides and place the 2 bottom cross braces between them (pocket holes facing the inside of the bed).
Next hold them in place using a 60" clamp (or daisy chain two 36" clamps together). Once secured, attach the cross braces
using 2.5" Kreg Pocket Hole screws. Repeat this step for the top braces.
Page 12 of 16
Assessment
11 At this point you should have 2 sides connected using the remaining cross braces.
Page 13 of 16
Add Remaining Corrugated Panels
12 Next you need to attach the remaining 2 corrugated panels using 1" Kreg Pocket Hole screws. Once attached, add the
additional support boards (optional) for the top plate.
Page 14 of 16
Add Top Plates (Optional)
13 Cut four 1"x4" cedar fence slats to 48" in length and attach to the top of each side using 1.25" exterior deck screws. At this
point the project is complete. Move the bed to the desired location and fill with compost and garden soil.
Page 15 of 16
4'x8' Version
14 If you are looking for a larger garden bed, you can double the size for only about $20 more. Replace the front and back
2"x4"x4' boards with 2"x4"x8' boards and replace the front and back 13.5"x4' corrugated panels with 13.5"x8' panels. This will
add 2 additional 2"x4"x8' boards and 1 additional 27"x8' corrugated panel.
Tip & Video Tutorial

15 A tip would be to fill the bottom half of the bed using Huglekultur method.
For a complete video tutorial on this build and Huglekultur, watch the YouTube video listed in the extras section of this plan.
Page 16 of 16

DIY Raised Garden Bed For Under $40

Uploaded by

Copyright:

Available Formats

DIY Raised Garden Bed For Under $40

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DIY Raised Garden Bed For Under $40

Uploaded by

Copyright:

Available Formats

DIY Raised Garden Bed for Under $40

4 Board , 2x4 , 96"

4 Board , 1x4 , 48"

Tape Measure 1 27" X 8' Corrugated Panel

8 Cross Braces , 2"x4"x48"

4 Top Plate , 1"x4"x48"

4 Corrugated Panels , 4'x13.5"

Tip & Video Tutorial

You might also like