SM-T819Y Manual Service

2.
Specification
2-1. GSM General Specification
WCDMA WCDMA WCDMA WCMDA

GSM850 EGSM 900 DCS1800 PCS1900
2100 1900 900 850
Freq.
Band[MHz] 824~849 880~915 1710~1785 1850~1910 1922~1977 1852~1907 880~915 824~849
Uplink/ 869~894 925~960 1805~1880 1930~1990 2110~2170 1932~1987 925~960 869~894
Downlink
UL: UL:
ARFCN 0~124 UL:9612~9888 UL:9262~9538 2712~2863 4132~4233
128~251 512~885 512~810
range & 975~1023 DL:10562~10838 DL:9662~9938 DL: DL:
2937~3088 4357~4458
Tx/Rx
45MHz 45MHz 95MHz 80MHz 190MHz 80MHz 45MHz 45MHz
spacing
Mod. Bit
270.833kbps 270.833kbps 270.833kbps 270.833kbps
rate/ 3.692us 3.692us 3.692us 3.692us
3.84Mcps 3.84Mcps 3.84Mcps 3.84Mcps
Bit Period
Time Slot FrameLength: FrameLength: FrameLength: FrameLength:

Period/ 576.9us 576.9us 576.9us 576.9us 10ms 10ms 10ms 10ms
Frame 4.615ms 4.615ms 4.615ms 4.615ms Slotlength: Slotlength: Slotlength: Slotlength:
0.667ms 0.667ms 0.667ms 0.667ms
Period
Modulation 0.3GMSK 0.3GMSK 0.3GMSK 0.3GMSK QPSK，HPSK QPSK，HPSK QPSKHQPSK QPSKHQPSK
24dBm~- 24dBm~ 24dBm~

MS Power 33dBm~5dBm 33dBm~5dBm 30dBm~0dBm 30dBm~0dBm 24dBm~-50dBm 50dBm -50dBm -50dBm
Power
5pcl ~ 19pcl 5pcl ~ 19pcl 0pcl ~ 15pcl 0pcl ~ 15pcl 3(max+24dBm) 3(max+24dBm) 3(max+24dBm) 3(max+24dBm)
Class
Sensitivity -102dBm -102dBm -100dBm -100dBm -106.7dBm -106.7dBm -106.7dBm -106.7dBm
TDMA Mux 8 8 8 8 8 8 8 8
Cell
35Km 35Km 2Km 2Km 2Km 2Km 2Km 2Km
Radius
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
2. Specification
2-2. GSM Tx Power Class
TX Power TX Power TX Power TX Power

GSM850 EGSM900 DCS1800 PCS1900
control level control level control level control level
5 32±2 dBm 5 32±2 dBm 0 30±3 dBm 0 29±3 dBm
6 31±2 dBm 6 30±2 dBm 1 29±3 dBm 1 27±3 dBm
7 29±2 dBm 7 28±2 dBm 2 27±3 dBm 2 25±3 dBm
8 27±2 dBm 8 26±2 dBm 3 25±3 dBm 3 23±3 dBm
9 25±2 dBm 9 24±2 dBm 4 23±3 dBm 4 21±3 dBm
10 24±2 dBm 10 23±2 dBm 5 20±3 dBm 5 20±3 dBm
11 22±2 dBm 11 21±2 dBm 6 18±3 dBm 6 18±3 dBm
12 20±2 dBm 12 19±2 dBm 7 16±3 dBm 7 16±3 dBm
13 18±2 dBm 13 17±2 dBm 8 14±3 dBm 8 14±3 dBm
14 16±2 dBm 14 15±2 dBm 9 12±4 dBm 9 12±4 dBm
15 15±2 dBm 15 13±2 dBm 10 10±4 dBm 10 10±4 dBm
16 13±3 dBm 16 11±3 dBm 11 8±4 dBm 11 8±4 dBm
17 9±3dBm 17 9±3dBm 12 6±4 dBm 12 6±4 dBm
18 7±3 dBm 18 7±3 dBm 13 4±4 dBm 13 4±4 dBm
19 5±3 dBm 19 5±3 dBm 14 2±5 dBm 14 2±5 dBm
15 0±5 dBm 15 0±5 dBm
2. Specification
2-3. LTE General Specification
LTE LTE
LTE Band1 LTE Band2 LTE Band3 LTE Band4 LTE Band5 LTE Band7 LTE Band8
Band17 Band20
Freq.
Band[MH
1920~1980 1850~1910 1710~1785 1710~1755 824~849 2500~2570 880~915 704~716 832~862
z]
2110~2170 1930~1990 1805~1880 2110~2155 869~894 2620~2690 925~960 734~746 791~821
Uplink/
Downlink
UL: UL: UL: UL: UL: UL:
UL: UL: UL:
18000~185 20400~206 20750~214 21450- 23730~238 24150~244
ARFCN 18600~19199 19200~19949 19950~20399
49
99 49 21799 49 49
range DL: DL: DL:
DL: DL: DL: DL: DL: DL:
600~1199 1200~1949 1950~2399
0~599 2400~2649 2750~3449 3450-3799 5730~5849 6150~6449
Tx/Rx
190MHz 80MHz 95MHz 400MHz 45MHz 120MHz 45MHZ 30MHz -41MHz
spacing
Channel
5/10/15/20 1.4/3/5/10/15/ 1.4/3/5/10/15/ 1.4/3/5/10/15/ 1.4/3/5/10 5/10/15/20 1.4/3/5/10M 5/10/15/20
Bandwidt 5/10 MHz
MHz 20 MHz 20 MHz 20 MHz MHz MHz Hz MHz
h
Modulatio QPSK, QPSK, QPSK, QPSK, QPSK, QPSK, QPSK, QPSK, QPSK,
n 16/64QAM 16/64QAM 16/64QAM 16/64QAM 16/64QAM 16/64QAM 16/64QAM 16/64QAM 16/64QAM
MS
-35~25.7 -35~25.7 -35~25.7 -35~25.7 -35~25.7 35~25.7
Power -35~25.7 dBm -35~25.7 dBm -35~25.7 dBm
dBm dBm dBm dBm dBm dBm
(MPR)
Sensitivit
(QPSK)
-97dBm -95dBm -94dBm -97dBm -95dBm -95dBm -94dBm -94dBm -94dBm
(BW
10MHz)
Cell
>5Km >5Km >5Km >5Km >5Km >5Km >5Km >5Km >5Km
Radius
3. Operation Instruction and Installation
Main Function
Item Description
OS Android V6.0 (Marshmallow)
2G : EDGE/GPRS 850/900/1800/1900
RF 3G : DC-HSPA+ 42/5.76 850/900/1900/2100
LTE : Band Cat6 300/50Mbps FDD 9 Band B1/B2/B3/B4/B5/B7/B8/B17/B20
Battery 5,870mAh
Base Band MSM8976 (A72/A53 1.8GHz Dual + 1.4GHz Quad)
Other RF A-GPS / BT4.1 / WiFi (802.11 a/b/g/n/ac MIMO) / USB v2.0/ UICC, GPS, GLONASS
Camera 8.0 MP AF(Rear) / 2.1M FF(Front)
LCD 9.7" OCTA QXGA, 2048×1536
RAM 3GB LPDDR3
Sensor Finger printer sensor ,Accelerometer, Hall, RGB Sensor, Grip Sensor
Charger 5V/2A(Normal), GH44-02802A

Accessory Data Cable 2.5pi, 1.2m, GH39-01801B
Ear phone: 3.5pi, 4pin, GH59-13967L
9. Reference Abbreviate
Reference Abbreviate
― AAC: Advanced Audio Coding.

― AVC : Advanced Video Coding.
― BER : Bit Error Rate
― BPSK: Binary Phase Shift Keying
― CA : Conditional Access
― CDM : Code Division Multiplexing
― C/I : Carrier to Interference
― DMB : Digital Multimedia Broadcasting
― EN : European Standard
― ES : Elementary Stream
― ETSI: European Telecommunications Standards Institute
― MPEG: Moving Picture Experts Group
― PN : Pseudo-random Noise
― PS : Pilot Symbol
― QPSK: Quadrature Phase Shift Keying
― RS : Reed-Solomon
― SI : Service Information
― TDM : Time Division Multiplexing
― TS : Transport Stream
1.Safety Precautions
1-1. Repair Precaution
Before attempting any repair or detailed tuning, shield the device from RF noise or static
electricity discharges.
Use only demagnetized tools that are specifically designed for small electronic repairs,
as most electronic parts are sensitive to electromagnetic forces.
Use only high quality screwdrivers when servicing products. Low quality screwdrivers can
easily damage the heads of screws.
Use only conductor wire of the properly gauge and insulation for low resistance, because of the low
margin of error of most testing equipment.
We recommend 22-gauge twisted copper wire.
Hand-soldering is not recommended, because printed circuit boards (PCBs) can be easily
damaged, even with relatively low heat. Never use a soldering iron with a power rating of
more than 100 watts and use only lead-free solder with a melting point below 250°C (482°F).
Prior to disassembling the battery charger for repair, ensure that the AC power is disconnected.
Always use the replacement parts that are registered in the SEC system. Third-party replacement parts
may not function properly.
1.Safety Precautions
1-2. ESD(Electrostatically Sensitive Devices) Precaution
Many semiconductors and ESDs in electronic devices are particularly sensitive to static discharge and
can be easily damaged by it. We recommend protecting these components with conductive anti-static
bags when you store or transport them.
Always use an anti-static strap or wristband and remove electrostatic buildup or dissipate
static electricity from your body before repairing ESDs.
Ensure that soldering irons have AC adapter with ground wires and that the ground wires are properly
connected.
Use only desoldering tools with plastic tips to prevent static discharge.
Properly shield the work environment from accidental electrostatic discharge before opening
packages containing ESDs.
The potential for static electricity discharge may be increased in low humidity environments,
such as air-conditioned rooms. Increase the airflow to the working area to decrease the
chance of accidental static electricity discharges.
6. Level 1 Repair
6-1. S/W installation
6-1-1. Required items in order to install S/W
 Installation program: Downloader Program (Odin3 v3.10..exe)

 SM-T819 set
 Data Cable
 Mobile device specific S/W: Binary files
※ Settings
Data Cable : GH39-01801E
6. Level 1 Repair
6-1-2. S/W Installation Program (Downloader program)

 Open up the S/W Installation Program by executing the "Odin3 v3.10..exe"
6. Level 1 Repair
1. Enable the check mark by click on the following options,

- Check Auto Reboot, Re-Partition, and F. Reset Time
- Check PIT
- Check BL, AP, CP, and CSC Files
* Note : "Odin v3.10 or above" checks MD5 checksum just after file selection.
6. Level 1 Repair
2. Enter into Download Mode

- Enter into Download Mode by pressing Home button, Volume Down button and Power On/Off
Button simultaneously followed by pressing Volume up button as a direction of the phone.
Power
Volume Down
Home
6. Level 1 Repair
3. Connect the device to PC via Data Cable.

Make sure that the one of communication ports [ID:COM] box is highlighted in
sky blue. The device is now connected with the PC and ready to download the
binary files in it.
6. Level 1 Repair
4. Start downloading the binary files into the device by clicking Start button on the
screen. The green colored "PASS!" sign will appear on the upper-left box if the
binary files have been successfully downloaded into the device.
5. Disconnect the device from the Data cable.
6. Once the device boots up, you can check the version of the binary file or name
by pressing the following code in sequence;
*#1234#
You can perform Factory Reset by Settings → Accounts → Backup and reset
6. Level 1 Repair
6-2 IMEI writing
6-2-1 Preparation
- New IMEI writing Program has been released.
- Supported Model : Models which CAB files are uploaded on HHPsvc INI File
category, instead of ini file.
- Refer to below IMEI writing procedure.
- H/W
- S/W
① Library Install To use Daseul, library files should be installed.
Refer to SVC Bulletin
“(11-82) Daseul (New IMEI writing Program) Library Install
guide_rev1.0”
②Launcher DASEUL_SVC_Launcher_v3_0_25 or higher

-Uploaded on HHPsvc Notice
③ Runtime File 1. DASEUL_Runtime_Ver_3.1.139.0.CAB or higher
-Uploaded on HHPsvc Notice
2. Make ‘ModelName’ folder at the same position with
launcher & Runtime file.
④Model File Copy Model File under the ‘Model Name’ folder
6. Level 1 Repair
6-2-2 IMEI writing Process

1. Run DASEUL_SVC_Launcher_v3.0.10.exe
2. Select Service Mode
3. Click and Select folder where the Launcher exists
SM-T719
6. Level 1 Repair
4. Select Model
SM-T719
5. Check IMEI and click System Setting
※Once you setup the setting, you don t have to

do it again, unless there is change. From second run of the IMEI program, check IMEI
and click Extract & Run.
SM-T719
6. Level 1 Repair
6. Check IMEI Write / IMEI Check and click IMEI SVC & Repair Option.
7. Check SVC , User Ticket No and click OK
6. Level 1 Repair
8. Click Hardware Config
9. Click Port Setting
6. Level 1 Repair
10. Select Port Number and SAVE
11.Click OK to proceed
6. Level 1 Repair
12. Click Model Info and OK when pop-up shows
SM-T377T
13. Click OK
6. Level 1 Repair
14. Input SKU_CODE and BUYER, then click Save button.

※ Refer to HHPsvc→IMEI Review to check SKU Code and buyer
SM-T719NDEXEF
15. Input IMEI Number and click Apply

SM-T377A
6. Level 1 Repair
16. ① Click Start, and input IMEI writing ID and Password →②input Ticket No
17. Connect the phone to Anyway JIG

※ When you connect the phone, the phone should be turned off.
After connecting the phone, the phone will be booted automatically.
18. IMEI Writing Proceeding
6. Level 1 Repair
19. IMEI Writing Success
6. Level 1 Repair
6-4. RF Calibration
6-1-1. Required items in order to calibrate RF
 Installation program: RF Calibration Program

- Daseul_Launcher_vx.x.xx.exe
- Daseul_CAL_ALL_Runtime_x.x.xxx.x.CAB
- Model File (SM-XXXXX_OPEN_CALIBRATION_VER_x.x.xxx.xx.CAB)
※ It is required to use the latest program.
 SM-T819 Tablet PC  R&S CMW500
 E3632A Power Supply  GPIB Cable (2ea)
 JIG BOX (GH81-11888A)  IF Cable (GH81-10623A)
 Adapter (GH81-11888K)  UART Serial Cable
 RF Cable (GH81-11962D, 1ea)
GH81-10623A GH81-10952A GH81-11171A

IF Cable
11 pin 7 pin (New) 7 pin (Old)
GH81-11962D GH81-11962D GH81-11962C GH81-11962F
1.35T, 500mm 1.35T, 1750mm 1.6T, 400mm 1.6T, 1700mm

RF Cable
(Manual)
GH81-11962A GH81-11962B GH81-11962E
Divider Divider Cable 50Ω terminator

4 Port Divider
6. Level 1 Repair
※ Setting
JIG BOX
IF Cable Serial Cable
E3632A
Power Supply
GPIB Cable
(2ea)
1.35Φ CMW 500

RF Cable
4 Port Divider Divider
RF Cable
50Ω Termination
6. Level 1 Repair
1. Run the RF Calibration Program Launcher, 'DASEUL_Launcher_vx.x.xx.exe'.
2. Check the 'Calibration' menu, and select 'Extract & Run'.
6. Level 1 Repair
3. Check the 'CAL' and open the model file, then select 'Start' button.
6. Level 1 Repair
4. Change the Line Type to 'Block Cell' and disable 'Smart Cloud Cell'.
6. Level 1 Repair
5. Set the GPIB address of MSTS(CMW500) and Power Supply(E3632A) to enter

'Hardware Config' and 'Save'. (Check the GPIB address of equipments in advance)
6. Level 1 Repair
6. Press 'OK' to start RF Calibration after completing all settings.
SM-T377T
6. Level 1 Repair
7-2. Battery Accumulated Usage Initialization
7-2-1 Notice
- It is necessary to initialize the battery accumulated usage for all cases of replacing
the batteries.
7-2-2 You need :

- SM-T719 set
- Laptop or Note PC
- Anyway Jig
- UART Serial Cable
- IF Test Cable (Different by models)
7-2-3 Lay-out
7-2-4 How to Initialize Battery Accumulated Usage
6. Level 1 Repair
6. Level 1 Repair

SM-T819Y Manual Service

Uploaded by

Copyright:

Available Formats

SM-T819Y Manual Service

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SM-T819Y Manual Service

Uploaded by

Copyright:

Available Formats

2.

2-1. GSM General Specification

WCDMA WCDMA WCDMA WCMDA

Time Slot FrameLength: FrameLength: FrameLength: FrameLength:

Modulation 0.3GMSK 0.3GMSK 0.3GMSK 0.3GMSK QPSK，HPSK QPSK，HPSK QPSKHQPSK QPSKHQPSK

24dBm~- 24dBm~ 24dBm~

Sensitivity -102dBm -102dBm -100dBm -100dBm -106.7dBm -106.7dBm -106.7dBm -106.7dBm

2-2. GSM Tx Power Class

TX Power TX Power TX Power TX Power

5 32±2 dBm 5 32±2 dBm 0 30±3 dBm 0 29±3 dBm

6 31±2 dBm 6 30±2 dBm 1 29±3 dBm 1 27±3 dBm

7 29±2 dBm 7 28±2 dBm 2 27±3 dBm 2 25±3 dBm

8 27±2 dBm 8 26±2 dBm 3 25±3 dBm 3 23±3 dBm

9 25±2 dBm 9 24±2 dBm 4 23±3 dBm 4 21±3 dBm

10 24±2 dBm 10 23±2 dBm 5 20±3 dBm 5 20±3 dBm

11 22±2 dBm 11 21±2 dBm 6 18±3 dBm 6 18±3 dBm

12 20±2 dBm 12 19±2 dBm 7 16±3 dBm 7 16±3 dBm

13 18±2 dBm 13 17±2 dBm 8 14±3 dBm 8 14±3 dBm

14 16±2 dBm 14 15±2 dBm 9 12±4 dBm 9 12±4 dBm

15 15±2 dBm 15 13±2 dBm 10 10±4 dBm 10 10±4 dBm

16 13±3 dBm 16 11±3 dBm 11 8±4 dBm 11 8±4 dBm

17 9±3dBm 17 9±3dBm 12 6±4 dBm 12 6±4 dBm

18 7±3 dBm 18 7±3 dBm 13 4±4 dBm 13 4±4 dBm

19 5±3 dBm 19 5±3 dBm 14 2±5 dBm 14 2±5 dBm

15 0±5 dBm 15 0±5 dBm

2-3. LTE General Specification

OS Android V6.0 (Marshmallow)

Base Band MSM8976 (A72/A53 1.8GHz Dual + 1.4GHz Quad)

Camera 8.0 MP AF(Rear) / 2.1M FF(Front)

LCD 9.7" OCTA QXGA, 2048×1536

RAM 3GB LPDDR3

Charger 5V/2A(Normal), GH44-02802A

― AAC: Advanced Audio Coding.

1-1. Repair Precaution

1-2. ESD(Electrostatically Sensitive Devices) Precaution

6-1. S/W installation

6-1-1. Required items in order to install S/W

 Installation program: Downloader Program (Odin3 v3.10..exe)

Data Cable : GH39-01801E

6-1-2. S/W Installation Program (Downloader program)

1. Enable the check mark by click on the following options,

2. Enter into Download Mode

3. Connect the device to PC via Data Cable.

5. Disconnect the device from the Data cable.

6-2 IMEI writing

②Launcher DASEUL_SVC_Launcher_v3_0_25 or higher

6-2-2 IMEI writing Process

2. Select Service Mode

3. Click and Select folder where the Launcher exists

5. Check IMEI and click System Setting

※Once you setup the setting, you don t have to

7. Check SVC , User Ticket No and click OK

8. Click Hardware Config

9. Click Port Setting

10. Select Port Number and SAVE

12. Click Model Info and OK when pop-up shows

14. Input SKU_CODE and BUYER, then click Save button.

15. Input IMEI Number and click Apply

 Installation program: Downloader Program (Odin3 v3.10..exe)