Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 12 views

    Specification For Fuel Oils: Draft Kenya Standard

    Uploaded by

    Vimal Patel
    19_4739_00_e

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Specification For Fuel Oils: Draft Kenya Standard

    Uploaded by

    Vimal Patel
    12 views6 pages
    19_4739_00_e

    Original Title

    19_4739_00_e

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    19_4739_00_e

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    12 views6 pages

    Specification For Fuel Oils: Draft Kenya Standard

    Uploaded by

    Vimal Patel
    19_4739_00_e

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    DRAFT KENYA STANDARD DKS 1310: 2019

    ICS 75.160.01

    Specification for fuel oils

    No copying of this standard without KEBS permission except as permitted by copyright law

    Second Edition 2019


    TECHNICAL COMMITTEE REPRESENTATION
    The following organizations were represented on the Technical Committee:

    Kenya Bureau of Standards ― Secretariat

    REVISION OF KENYA STANDARDS


    In order to keep abreast of progress in industry, Kenya Standards shall be regularly reviewed. Suggestions for
    improvements to published standards, addressed to the Managing Director, Kenya Bureau of Standards, are
    welcome.

    © Kenya Bureau of Standards, 2019

    Copyright. Users are reminded that by virtue of section 6 of the Copyright Act, Cap.130 of the Laws of Kenya, copyright subsists in all Kenya
    Standards and except as provided under section 7 of this Act, no Kenya Standard produced by Kenya Bureau of Standards may be reproduced,
    stored in a retrieval system in any form or transmitted by any means without prior permission in writing from the Managing Director.

    Permission may be conditional on an appropriate royalty payment.

    Care should be taken to ensure that material used is from the current edition of the standard and that it is updated whenever the standard is
    amended or revised. The number and date of the standard should therefore be clearly identified.

    The use of material in print or in electronic form to be used commercially with or without payment or in commercial contracts is subject to
    payment of a royalty.

    ISBN 9966-23-208-7
    KENYA STANDARD DKS 1310: 2019
    ICS 75.160.01

    Specification for fuel oils

    KENYA BUREAU OF STANDARDS (KEBS)

    Head Office: P.O. Box 54974, Nairobi-00200, Tel.: (+254 020) 605490, 602350, Fax: (+254 020)
    604031
    E-Mail: info@kebs.org, Web:http://www.kebs.org

    Coast Region Lake Region Rift Valley Region


    P.O. Box 99376, Mombasa-80100 P.O. Box 2949, Kisumu-40100 P.O. Box 2138, Nakuru-
    20100
    Tel.: (+254 041) 229563, 230939/40Tel.: (+254 057) 23549, 22396 Tel.: (+254 051) 210553, 210555
    Fax: (+254 041) 229448 Fax: (+254 057) 21814
    PREFACE
    This Kenya Standard has been prepared by the Technical Committee on Petroleum and Petroleum
    Products.
    SPECIFICATION FOR FUEL OILS

    1. SCOPE

    This Kenya Standard prescribes requirements and test methods for fuel oils intended for oil-
    fired furnaces both for industrial and marine uses.

    2. NORMATIVE REFERENCE

    3. REQUIREMENTS

    3.1 General The material shall be hydrocarbon oils derived from petroleum or shale. It shall be
    free from grit and other foreign impurities.

    3.2 The material shall also comply with the requirements prescribed in Table 1, when tested
    according to the corresponding test methods.

    Table 1. Requirements

    S. No. Property Requirement Test Method


    1. Viscosity @50˚C, cSt, max 180 ASTM D445
    2. Density @ 20 ˚C, Kg/L, max 0.990 ASTM D1298
    3. Conradson Carbon Residue, % wt., max 15 ASTM D189
    4. Sulphur Content, % wt., max 2 ASTM D4294
    5. Vanadium content, mg/kg, max 200 IP 288
    6. Asphaltenes, % wt., max 10 IP 143
    7. Ash content, % wt., max 0.12 ASTM 482
    8. Sodium content, mg/kg, max 1/3 vanadium IP 288, IP 501
    9. Water content, % vol, max 0.5 ASTM D95
    10. Pour point, ˚C, max 15 ASTM D97
    11. Flash point, ˚C, min 66 ASTM D93
    12. Aluminium silicon+ silicon, mg/Kg, max 50 ASTM D5184
    13. Net calorific value, MJ/Kg, min 40.5 ASTM D 4868
    14. CCAI (calculated carbon aromatic Index) TO BE REPORTED ISO 8217
    15. Nitrogen content, % wt., max 0.4 ASTM D3228
    16. Sediment by extraction, % wt., max 0.15 ASTM D473
    17. Existent sediment, % m/m, max 0.1 IP 395
    18. Potential sediment, % m/m, max 0.1 IP 390
    19. Neutralization strong acid number, mg NIL ASTM D974
    KOH/g
    20. Calcium, mg/Kg, max 30 IP 470, IP 501
    21. Phosphorus, mg/Kg, max 15 IP 500, IP 501
    22. Zinc , mg/Kg, max 15 IP 470,IP 501
    23. Others No contamination of lubes.

    4.0 Packing and marking

    4.1 Packing

    The condition of the containers, rail tankers and road tank vehicles shall be such as not to be
    detrimental to the quality of the fuel during normal transportation and storage. The containers shall
    be acceptably sealed or leak proof, clean, and free from materials soluble in fuel oil.
    4.2 Marking

    4.2.1 The following information shall appear in legible and indelible marking on each container or
    in case of fuel oil filled into bulk storage tanks, in the storage and consignment documents of each
    road tank wagon or rail tank wagon.

    a) the supplier’s and receiver’s name and address;

    b) the name “FUEL OIL”;

    c) the quantity in litres or metric tonnes;

    d) the batch/lot number;

    e) the word “FLAMMABLE MATERIAL”; and

    f) the warning “DANGER FUEL OIL”.

    You might also like