Engineering Workshop: Laboratory Manual
Engineering Workshop: Laboratory Manual
Engineering Workshop: Laboratory Manual
ENGINEERING WORKSHOP
LABORATORY MANUAL
SAFETY RULES & UNSAFE PRACTICES
Remember that “accidents do not occur, they are caused”. With this in mind, strictly follow the
general safety rules given below and safe practices indicated in brief under each section.
3. Avoid wearing clothing that might catch, moving or rotating parts. Long sleeves of shirts,
long hair, neck tie and jewellery are definite hazards in the shop.
4. Wear safety shoes. Do not wear canvas shoes; they give no resistance to hard
objects dropped on the feet.
9. Use tools correctly and do not use them if they are not in proper working condition.
10. Wear safety goggles when working in areas, where sparks or chips of metal are
flying.
11. Get to know who in-charge of first aid is and where boxes are placed and where the first
aid can be found in case of emergency.
CONTENTS
1. FITTING 04 - 16
2. CARPENTRY 17 - 27
1. FITTING
Introduction
Machine tools are capable of producing work at a faster rate, but, there are occasions when
components are processed at the bench. Sometimes, it becomes necessary to replace or repair
component which must be fit accurately with another component on reassembly. This involves a
certain amount of hand fitting. The assembly of machine tools, jigs, gauges, etc, involves certain
amount of bench work. The accuracy of work done depends upon the experience and skill of the
fitter.
The term ‘bench work’ refers to the production of components by hand on the bench, where as
fitting deals which the assembly of mating parts, through removal of metal, to obtain the required
fit.
Both the bench work and fitting requires the use of number of simple hand tools and considerable
manual efforts. The operations in the above works consist of filing, chipping, scraping, sawing
drilling, and tapping.
Holding Tools:
Bench Vice
The bench vice is a work holding device. It is the most commonly used vice in a fitting shop. The
bench vice is shown in figure below.
It is fixed to the bench with bolts and nuts. The vice body consists of two main parts, fixed jaw
and movable jaw. When the vice handle is turned in a clockwise direction, the sliding jaw forces
the work against the fixed jaw. Jaw plates are made of hardened steel. Serrations on the jaws
ensure a good grip. Jaw caps made of soft material are used to protect finished surfaces, gripped
in the vice. The size of the vice is specified by the length of the jaws.
V‐block is rectangular or square block with a V‐groove on one or both sides opposite to each
other. The angle of the ‘V’ is usually 900. V‐block with a clamp is used to hold cylindrical work
securely, during layout of measurement, for measuring operations or for drilling for this the bar is
faced longitudinally in the V‐Groove and the screw of V‐clamp is tightened. This grip the rod is
firm with its axis parallel to the axis of the v‐groove.
C‐ Clamp
This is used to hold work against an angle plate or v‐block or any other surface, when gripping is
require Its fixed jaw is shaped like English alphabet ‘C’ and the movable jaw is round in shape
and directly fitted to the threaded screw at the end .The working principle of this clamp is the
same as that of the bench vice.
Surface Plate
The surface plate is machined to fine limits and is used for testing the flatness of the work piece.
It is also used for marking out small box and is more precious than the marking table. The degree
of the finished depends upon whether it is designed for bench work in a fitting shop or for using
in an inspection room; the surface plate is made of Cast Iron, hardened Steel or Granite stone. It
is specified by length, width, height and grade. Handles are provided on two opposite sides, to
carry it while shifting from one place to another (refer figure in next page).
It is measuring and marking tool for 900 angle .In practice, it is used for checking the squareness
of many types of small works when extreme accuracy is not required .The blade of the Try square
is made of hardened steel and the stock of cast Iron or steel. The size of the Try square is specified
by the length of the blade.
Scriber
A Scriber is a slender steel tool, used to scribe or mark lines on metal work pieces. It is made of
hardened and tempered High Carbon Steel. The Tip of the scriber is generally ground at 12oto
15o.
It is generally available in lengths, ranging from 125mm to 250mm .It has two pointed ends the
bent end is used for marking lines where the straight end cannot real.
Dot Punch is used to lightly indent along the layout lines, to locate center of holes and to provide
a small center mark for divider point, etc. for this purpose, the punch is ground to a conical point
having 60° included angle.
Center Punch is similar to the dot punch, except that it is ground to a conical point having 90°
included angle. It is used to mark the location of the holes to be drilled.
Fig: Calipers
Cutting Tools:
Hack Saw
The Hack Saw is used for cutting metal by hand. It consists of a frame, which holds a thin blade,
firmly in position. Hacksaw blade is specified by the number of teeth for centimeter. Hacksaw
blades have a number of teeth ranging from 5 to 15 per centimeter (cm). Blades having lesser
number of teeth per cm are used for cutting soft materials like aluminum, brass and bronze. Blades
having larger number of teeth per centimeter are used for cutting hard materials like steel and cast
Iron.
Hacksaw blades are classified as (i) All hard and (ii) flexible type. The all hard blades are made of
H.S.S, hardened and tempered throughout to retain their cutting edges longer. These are used to
cut hard metals. These blades are hard and brittle and can break easily by twisting and forcing
them into the work while sawing. Flexible blades are made of H.S.S or low alloy steel but only the
teeth are hardened and the rest of the blade is soft and flexible. These are suitable for use by un‐
skilled or semi‐skilled persons.
The teeth of the hacksaw blade are staggered, as shown in figure and known as a ‘set of teeth’.
These make slots wider than the blade thickness, preventing the blade from jamming.
Chisels
Chisels are used for removing surplus metal or for cutting thin sheets. These tools are made from
0.9% to 1.0% carbon steel of octagonal or hexagonal section. Chisels are annealed, hardened and
tempered to produce a tough shank and hard cutting edge. Annealing relieves the internal stresses
in a metal. The cutting angle of the chisel for general purpose is about 60°.
Twist Drill
Twist drills are used for making holes. These are made of High speed steel. Both straight and taper
shank twist drills are used. The parallel shank twist drill can be held in an ordinary self – centering
drill check. The tapper shank twist drill fits into a corresponding tapered bore provided in the
drilling machine spindle (see figure in next page).
A tap is a hardened and steel tool, used for cutting internal thread in a drill hole. Hand Taps are
usually supplied in sets of three in each diameter and thread size. Each set consists of a tapper tap,
intermediate tap and plug or bottoming tap. Taps are made of high carbon steel or high speed steel
(see figure in next page).
Bench Drilling Machine
Holes are drilled for fastening parts with rivets, bolts or for producing internal thread. Bench
drilling machine is the most versatile machine used in a fitting shop for the purpose. Twist drills,
made of tool steel or high speed steel are used with the drilling machine for drilling holes.
1. Select the correct size drills, put it into the check and lock it firmly
2. Adjust the speed of the machine to suit the work by changing the belt on the pulleys. Use high
speed for small drills and soft materials and low speed for large diameter drills and hard
materials.
3. Layout of the location of the pole and mark it with a center punch.
4. Hold the work firmly in the vice on the machine table and clamp it directly on to the machine
table.
5. Put on the power, locate the punch mark and apply slight pressure with the Feed Handle.
Fig: Bench Drill
Finishing Tools:
Reamers
Reaming is an operation of sizing and finishing a drilled hole, with the help of a cutting tool called
reamer having a number of cutting edges. For this, a hole is first drilled, the size of which is slightly
smaller than the finished size and then a hand reamer or machine reamer is used for finishing the
hole to the correct size.
Hand Reamer is made of High Carbon Steel and has left‐hand spiral flutes so that, it is prevented
from screwing into the whole during operation. The Shank end of the reamer is made straight so
that it can be held in a tap wrench. It is operated by hand, with a tap wrench fitted on the square
end of the reamer and with the work piece held in the vice. The body of the reamer is given a slight
tapper at its working end, for its easy entry into the whole during operation, it is rotated only in
clock wise direction and also while removing it from the whole.
Fig: Reamers
Files
Filing is one of the methods of removing small amounts of material from the surface of a metal
part. A file is hardened steel too, having small parallel rows of cutting edges or teeth on its surfaces.
On the faces, the teeth are usually diagonal to the edge. One end of the file is shaped to fit into a
wooden handle. The figure shows various parts of a hand file. The hand file is parallel in width
and tapering slightly in thickness, towards the tip. It is provided with double cut teeth. On the
faces, single cut on one edge and no teeth on the other edge, which is known as a safe edge.
Files are classified according to their shape, cutting teeth and pitch or grade of the teeth. The figure
shows the various types of files based on their shape.
Miscellaneous Tools:
It is similar to ball peen hammer, except the shape of the peen. This is used for chipping, riveting,
bending and stretching metals and hammering inside the curves and shoulders.
Straight‐Peen Hammer
This is similar to cross peen hammer, but its peen is in‐line with the hammer handle. It is used for
swaging, riveting in restricted places and stretching metals.
-
Viva Questions
Question: Name the material with which a vice body is normally made of. What is the characteristic
of this material?
Timber:
Timber is the name given to the wood obtained from well grown trees. The trees are cut, sawn into
various sizes to suit building purposes.
The word, ‘grain’, as applied to wood, refers to the appearance or pattern of the wood on the cut
surfaces. The grain of the wood is a fibrous structure and to make it strong, the timber must be so
cut, that the grains run parallel to the length.
Timber Sizes
Timber sold in the market is in various sizes and shapes. The following are the common shapes
and sizes.
a. Log ‐ The trunk of the tree which is free from branches.
b. Balk ‐ The log, sawn to have roughly square cross section.
c. Post ‐ A timber piece, round or square in cross section, having its diameter or side from
175 to 300mm.
d. Plank ‐ A sawn timber piece, with more than 275 mm in width, 50 to 150 mm in
thickness and 2.5 to 6.5 meters in length.
e. Board ‐ A sawn timber piece, below 175 mm in width and 30 to 50 mm in thickness.
f. Reapers‐ Sawn timber pieces of assorted and non‐standard sizes, which do not confirm to the
above shapes and sizes.
Classification of Timber
Wood suitable for construction and other engineering purposes is called timber. Woods in general
are divided into two broad categories: Soft woods and Hard woods.
Soft woods are obtained from conifers, kair, deodar, chir, walnut and seemal. Woods obtained from
teak, sal, oak, shisham, beach, ash mango, neem and babul are known as hard wood, but it is highly
durable.
Another classification of woods is based on the name of the trees like teak, babul, shisham, neem,
kair, chir, etc.
Seasoning of Wood
A newly felled tree contains considerable moisture content. If this is not removed, the timber
is likely to wrap, shrink, crack or decay. Seasoning is the art of extracting the moisture content
under controlled conditions, at a uniform rate, from all the parts of the timber. Only seasoned
wood should be used for all carpentry works. Seasoning makes the wood resilient and lighter.
Further, it ensures that the wood will not distort after it is made into an object.
a. It should have minimum moisture content, i.e., the timber should be well seasoned.
b. The grains of wood should be straight and long.
c. It must retain its straightness after seasoning.
d. It should produce near metallic sound on hammering.
e. It should be free from knots or cracks.
f. It should be of uniform color, throughout the part of the wood.
g. It should respond well to the finishing and polishing operations.
h. During driving the nails and screw, it should not split easily.
Marking and Measuring Tools:
Accurate marking and measurement is very essential in carpentry work, to produce parts to
exact size. To transfer dimensions onto the work; the following are the marking and measuring
tools that are required in a carpentry shop.
Steel rule is a simple measuring instrument consisting of a long, thin metal strip with a marked
scale of unit divisions. It is an important tool for linear measurement. Steel tape is used for
large measurements, such as marking on boards and checking the overall dimensions of the
work.
Fig: Steel Rule and Steel Tape
Marking Gauge
It is a tool used to mark lines parallel to the edge of a wooden piece. It consists of a square
wooden stem with a sliding wooden stock (head) on it. On the stem is fitted a marking pin,
made of steel. The stock is set at any desired distance from the marking point and fixed in
position by a screw. It must be ensured that the marking pin projects through the stem, about
3 mm and the end are sharp enough to make a very fine line. A mortise gauge consists of two
pins. In this, it is possible to adjust the distance between the pins, to draw two parallel lines on
the stock.
Try ‐ Square
It is used for marking and testing the squareness and straightness of planed surfaces. It consists
of a steel blade, fitted in a cast iron stock. It is also used for checking the planed surfaces for
flatness. Its size varies from 150 to 300 mm, according to the length of the blade. It is less
accurate when compared to the try‐square used in the fitting shop.
It is used for marking on timber. It is made of steel having one end pointed and the other end
formed into a sharp cutting edge (refer Fig. in next page).
Bevel Square
It is used for laying‐out and checking angles. The blade of the bevel is adjustable and may be
held in place by a thumb screw. After it is set to the desired angle, it can be used in much the
same way as a try‐square. A good way to set it to the required angle is to mark the angle on a
surface and then adjust the blade to fit the angle
Holding Tools:
Carpenter's Vice
It is used as a work holding device in a carpenter shop. Its one jaw is fixed to the side of the
table while the other is movable by means of a screw and a handle. The Carpenter's vice jaws
are lined with hard wooden' faces
Fig: Carpenters Vice Fig: C‐Clamp
C‐Clamp
It is used for holding small works (see figure above)
Bar Cramp
It is made of steel bar of T‐section, with malleable iron fittings and a steel screw. It is used for
holding wide works such as frames or tops.
Planing Tools:
Planing is the operation used to produce flat surfaces on wood. A plane is a hand tool used for
this purpose. The cutting blade used in a plane is very similar to a chisel. The blade of a plane
is fitted in a wooden or metallic block, at an angle.
Types of Planes:
Jack Plane
It is the most commonly used general purpose plane. It is about 35 cm long. The cutting iron
(blade) should have a cutting edge of slight curvature. It is used for quick removal of material
on rough work and is also used in oblique planning.
Smoothing Plane
It is used for finishing work and hence, the blade should have a straight cutting edge. It is about
20 to 25 cm long. Being short, it can follow even the slight depressions in the stock, better
than the jack plane. It is used after using the jack plane.
Rebate Plane
It is used for making a rebate. A rebate is a recess along the edge of a piece of wood, which is
generally used for positioning glass in frames and doors.
Plough Plane
It is used to cut grooves, which are used to fix panels in a door. The following figure shows
the various types of planes mentioned above.
Cutting Tools:
Saws
A saw is used to cut wood into pieces. There are different types of saws, designed to suit
different purposes. A saw is specified by the length of its toothed edge.
Types of Saws:
Cross‐Cut Saw or Hand Saw
It is used to cut across the grains of the stock. The teeth are so set that the saw kerf will be
wider than the blade thickness. This allows the blade to move freely in the cut, without sticking
Rip Saw
It is used for cutting the stock along the grains. The cutting edge of this saw makes a steeper
angle, i.e., about 60° whereas that of crosscut saw makes an angle of 45° with the surface of
the stock.
Tenon Saw
It is used for cutting the stock either along or across the grains. It is used for cutting tenons
and in fine cabinet work. However, it is used for small and thin cuts. The blade of this saw is
very thin and so it is stiffened with a thick back steel strip. Hence, this is sometimes called as
back‐saw. In this, the teeth are shaped like those of cross‐cut saw.
Compass Saw
It has a narrow, longer and stronger tapering blade, which is used for heavy works . It is mostly
used in radius cutting. The blade of this saw is fitted with an open type wooden handle.
Chisels are used for cutting and shaping wood accurately. Wood chisels are made in various
blade widths, ranging from 3 to 50 mm. They are also made in different blade lengths. Most
of the wood chisels are made into tang type, having a steel shank which fits inside the handle.
These are made of forged steel or tool steel blades.
Fig: Types of Chisels
Types of Chisels:
Firmer Chisel
The word 'firmer' means 'stronger' and hence firmer chisel is stronger than other
chisels. It is a general purpose chisel and is used either by hand pressure or by a mallet. The
blade of a firmer chisel is flat, as shown in figure.
Dovetail Chisel
It has a blade with a beveled back, as shown in Figure, due to which it can enter sharp comers
for finishing, as in dovetail joints.
Mortise Chisel
It is used for cutting mortises and chipping inside holes, etc. The cross‐section of the
mortise chisel is proportioned to withstand heavy blows during mortising. Further, the cross‐
section is made stronger near the shank..