P00592320 - 3 - CNCG Burner Sequences

Document Description Pages Rev.
SEQ-28.01 Drawing list 1 3

This document is the exclusive intellectual property of Valmet Corporation and/or its subsidiaries and is furnished solely for operating and maintaining the specific project. Re-use of the document for any other
SEQ-28.02 Legend sheet 1 3
SEQ-28.03 CNCGB NG start sequence 5 3
SEQ-28.04 CNCGB NG stop sequence 3 3
SEQ-28.05 CNCGB NG local controls 1 3
SEQ-28.06 CNCGB NG burner failure 1 3
SEQ-28.07 CNCGB NG equipment in stop position 1 3

project or purpose is prohibited. The document or the information shall not be reproduced, copied or disclosed to a third party without prior written consent of the company.
SEQ-28.08 CNCGB Igniter cylinder 1 3
SEQ-28.09 CNCGB Igniter 1 3
SEQ-28.11 CNCGB NG valves 1 3
SEQ-28.12 CNCGB NG leakage test sequence 5 3
SEQ-28.13 CNCGB NG leakage test 1 3
SEQ-28.14 CNCGB igniter local control 1 3
SEQ-28.15 CNCGB combustion air monitoring 1 3
SEQ-28.16 CNCGB NG lance 1 3
SEQ-28.41 CNCGB CNCG start sequence 3 3
SEQ-28.42 CNCGB CNCG stop sequence 3 3
SEQ-28.43 CNCGB CNCG local controls 1 3
SEQ-28.44 CNCGB CNCG burner failure 1 3
SEQ-28.45 CNCGB CNCG equipment in stop pos 1 3
SEQ-28.46 CNCGB CNCG valves 1 3
SEQ-28.48 CNCGB CNCG lance pressure monitoring 1 3
SEQ-28.70 CNCGB Common local controls 1 3
SEQ-28.71 CNCGB rodder 1 3
SEQ-28.72 CNCGB Support fuel start release 1 3
SEQ-28.73 Oil burner start conditions 1 3
PRELIMINARY
Rev. Created By Inspected By Released By Project: 110374 Planta Arauco CNCG Drawn 6/27/2018/ATVAKI2 Design TREVESSAPA Rev.
1 8/3/2018/FTAMSLAP 8/3/2018/FTAMJNS 8/3/2018/FTAMSRE Name: CNCG burner Chkcd FTAMJNS Appr. FTAMSRE 3
2 8/31/2018/TREVESSAPA
8/31/2018/FTAMJNS 8/31/2018/FTAMSRE Cust. Doc ID Page:
DRAWING LIST
3 5/29/2020/TREJARVEJO
5/29/2020/FTAMJNS 5/29/2020/FTAMSRE SEQ-28.01
Pos. 1
Doc ID: P00592320
0 1 2 3 4 5 6 7
IF THE SEQUENCE DON'T HAVE THE FOLLOWING OPERATIONS PROT ->A AON ->M MON INIT REL
THEN THEY ARE NOT SHOWNED AT THE DIAGRAM A
SEQUENCE START BLOCK

->M SET SEQUENCE TO MANUAL (=OPERATOR) CONTROL (PULSE-WISE)
DIGITAL LOGIC
->A SET SEQUENCE TO AUTO CONTROL (PULSE-WISE)
&
MON SEQUENCE MANUAL (OPERATOR) START/STOP AND - GATE
SEQUENCE STARTS ALWAYS FROM BEGINNING
TO FIRST STEP
INIT SEQUENCE IS STOPPED AND RETURNED
1
TO BEGINNING OR - GATE
FROM PREVIOUS STEP
AON SEQUENCE AUTOMATIC START (PULSE-WISE) B
IF ONLY AON, THEN OPERATOR CAN NOT MAKE OPERABLE WAITING TIME:
ANY CHANGES WHEN THE SEQUENCE IS RUNNING =1
- OPERABLE FROM DISPLAY XOR - GATE
- ELAPSED TIME DISPLAY,
PROT SEQUENCE IS FORCED TO MANUAL AND STARTED
IF TIME > 60 s
STEP NAME
REL SEQUENCE IS RELEASED TO START NEGATION
OPERABLE WAITING TIME MONITORING TIME ACTION
WAITING TIME 1 s OWT +5s
0...5s FAILURE
ON TIME DELAY, ON
C
STEP NUMBER
OFF TIME DELAY, OFF
JUMP CONDITIONS
STEP JUMP PULSE

1
Into page: 1
&
O SR
TRANSITION CONDITIONS O 00 01 10 11
S
0 0 0 1 0
R
1 1 0 1 0 D
TO NEXT STEP
WAITING TIME:
-THE NEXT STEP CAN NOT BE ACTIVATED
UNTIL THE WAITING TIME IS PASSED
-WAITING TIME DOESN'T APPLY TO JUMP CONDITIONS FROM PREVIOUS STEP PAGE MERGE INSIDE SAME DOC. GROUP
2
Into page: 1
MONITORING TIME: END STEP

-IF NEXT STEP IS NOT ON DURING
MONITORING TIME THEN STEP FAILURE WAITING TIME MONITORING TIME ACTION
N E
s s
END STEP SHALL STOP THE SEQUENCE AND

RETURN IT TO BEGINNING IN ALL MODES (M AND A)
PRELIMINARY
LEGEND SHEET
Pos. 1
Doc ID: P00592320
0 1 2 3 4 5 6 7
VALID
.S1 BMS2
CNCG B LEAKAGE TEST A
SEQ-28.13 CNCGB NG leakage test
START COND. OK
.S1 BMS2
CNCG MAIN INTERLOCK CNCG B NG START SEQUENCE RUN
INT-28.11 CNCGB main common interlocks NC-CB3-KJ0051.S11
NG EQUIPMENT IN STOP POS. STATUS
.S1 BMS2 RUNNING
CNCG B EQ IN STOP POS .S11
3s SEQ-28.07 CNCGB NG equipment in stop position CNCG B NG START SEQUENCE

NG START DCS DI CNT-28.01 CNCG burner NG flow and pressure
.S4 BMS2 STEP S11 CNT-28.21 CNCG burner combustion air B
CNCG B SUPRT BURN OPR STRT NOT ANY BURNER STARTING BMS2 DO
SEQ-28.72 CNCGB Support fuel start release .S1 BMS2
1 BURNERS STARTING STATUS &
3s INT-28.26 CNCGB CNCG burner status
LOCAL START & IGNITION GAS PRESSURE OK
252-LCP-150.PB08.S1 BMS2 .S1 BMS2
CNCG B NG burner start NG PRESSURE TO IGNITERS
SEQ-28.05 CNCGB NG local controls INT-28.26 CNCGB CNCG burner status
OIL&MEOH BURNER NOT RUNNING CNCG B NG READY TO START

BMS2 READY TO START C
Oil burner running/starting NC-CB3-KJ0051.S1
INT-28.27 Oil burner start conditions STATUS
RUNNING
.S12 BMS2
CNCG B NG STOP SEQUENCE
SEQ-28.04 CNCGB NG stop sequence DCS DI
STEP S1
BMS2 DO
BURNER NG FAILURE READY TO START
.S4 BMS2 .S1 BMS2
CNCG B NG FAILURE CONTROL CNCG B NG START SEQUENCE
SEQ-28.06 CNCGB NG burner failure SEQ-28.05 CNCGB NG local controls
D
SEQUENCE STEP NUMBER
NC-CB3-KJ0051.I1
STATUS
1 ALWAYS
A-MODE.
PROT AON REL DCS DI RUNNING
STEP INTEGER
I1
STOP COMMAND .S11 BMS2
.S10 BMS2 INIT CNCG B NG START SEQUENCE BMS2 DO CNCG B NG START SEQUENCE
CNCG B NG OPERATOR CONTROL INT-28.26 CNCGB CNCG burner status
STEP INT-28.27 Oil burner start conditions
SEQ-28.04 CNCGB NG stop sequence
SEQ-28.05 CNCGB NG local controls
SEQ-28.06 CNCGB NG burner failure E
SEQ-28.12 CNCGB NG leakage test sequence
SEQ-28.70 CNCGB Common local controls
SEQ-28.72 CNCGB Support fuel start release
STEP 1
PRELIMINARY
CNCGB NG START SEQUENCE
Pos. 1
Doc ID: P00592320
0 1 2 3 4 5 6 7
IN AUTO MODE STEP START

252-HIC-817 BMS2 A
CNCG B combustion air damper
SEQ-28.15 CNCGB combustion air monitoring
COMBUSTION AIR DAMPER OPEN 252-HIC-817.S2
S2 STEP
252-HIC-817.S3 AUTO MODE ON
S3 STEP
IN AUTO-MODE WAITING TIME MONITORING TIME ACTION BMS2 DO DI DCS 252-HIC-817
252-HIC-817 DCS DO DI BMS2 1 1s s
AIR DAMPER NOT CLOSED &

252-HIC-817.S1 BMS2
CNCG Comb.air damper open B
INT-28.11 CNCGB main common interlocks
GAS LANCE IN
AUTO IN
WAITING TIME MONITORING TIME ACTION 252-HSV-812
2 1s s
CNCG B natural gas lance in-out
SEQ-28.16 CNCGB NG lance
SET MONITORING ON
252-HIC-817 BMS2
IN POSITION & NOT FAILURE CNCG B combustion air damper
252-HSV-812.S11 BMS2 SEQ-28.15 CNCGB combustion air monitoring
SEQ-28.16 CNCGB NG lance C
IGNITER CYLINDER IN
AUTO IN
3 1s s
CNCG B igniter in-out
SEQ-28.08 CNCGB Igniter cylinder
IN POSITION & NOT FAILURE

252-HSV-811.S11 BMS2
CNCG B igniter in-out D
IGNITER START
AUTO START
WAITING TIME MONITORING TIME ACTION 252-BX-804
4 1s s
CNCG B igniter
SEQ-28.09 CNCGB Igniter
IGNITER FLAME & CONTROL ON

252-BX-804.S3 BMS2
CNCG B igniter
INT-28.14 CNCGB igniter E
STEP 5
PRELIMINARY
Pos. 2
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP 4
A
FLOW CONTROL TO IGN. POSITION 252-PIC-835.S21
S21 STEP
50 %
WAITING TIME MONITORING TIME ACTION BMS2 DO DI DCS 252-PIC-835.S21
5 1s s
CNCG B natural gas pressure
CNT-28.01 CNCG burner NG flow and pressure
252-PIC-835.S23
S23 STEP
CONTROLLER IN MANUAL MODE
252-FIC-805 DCS DO DI BMS2
CNCG B natural gas flow
CLOSE GAS VENT VALVE

B
AUTO CLOSE
6 1s s
CNCG B natural gas vent valve
SEQ-28.11 CNCGB NG valves
CLOSED LIMIT & NOT FAILURE

252-HSV-830.S12 BMS2
SPARE
C
WAITING TIME MONITORING TIME ACTION
7 1s s
D
OPEN GAS VALVES
AUTO OPEN
8 1s s
CNCG B natural gas valve 1
OPEN LIMIT & NOT FAILURE SEQ-28.11 CNCGB NG valves
252-HSV-814.S11 BMS2
AUTO OPEN
252-HSV-815
&
252-HSV-815.S11 BMS2
CNCG B natural gas valve 2 E
STEP 9
PRELIMINARY
Pos. 3
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP 8
MAIN FLAME DETECTING A


9 1s s
CNCG B MAIN FLAME ON

252-BS-803 BMS2
CNCG B flame scanner
INT-28.13 CNCGB NG flame monitoring STABILIZING TIME
WAITING TIME MONITORING TIME ACTION B

10 5s s

252-BS-803 BMS2
INT-28.13 CNCGB NG flame monitoring
STOP IGNITER
AUTO STOP
WAITING TIME MONITORING TIME ACTION 252-BX-804 C
11 1s s
CNCG B igniter
252-PIC-835.S22
S22 STEP
RESET
BMS2 DO DI DCS 252-PIC-835.S22
IGNITER FLAME ON CNCG B natural gas pressure
252-BX-804.S1 BMS2 CNT-28.01 CNCG burner NG flow and pressure
CNCG B igniter
INT-28.14 CNCGB igniter
IGNITER CYLINDER OUT
AUTO OUT D
12 20s s
OUT POSITION & NOT FAILURE

252-HSV-811.S12 BMS2
SEQ-28.08 CNCGB Igniter cylinder NG FLOW AUTO 252-FIC-805.S1
S1 STEP
AUTO MODE ON
WAITING TIME MONITORING TIME ACTION BMS2 DO DI DCS 252-FIC-805
E
13 1s s
PRELIMINARY
STEP 14
Pos. 4
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP 13
READY
A

14 s s
PRELIMINARY
Pos. 5
Doc ID: P00592320
0 1 2 3 4 5 6 7
IGNITER/BLOWING OK
.S3 BMS2
CNCG MAIN INTERLOCK
A
OIL&MEOH BURNER NOT RUNNING CNCG B NG READY TO STOP

BMS2 READY TO START
NC-CB3-KJ5097.S1
Oil burner running/starting &
INT-28.27 Oil burner start conditions STATUS
RUNNING
DCS DI
.S11 BMS2 STEP S1
CNCG B NG LEAKAGE TEST SEQ B
BMS2 DO CNCG B NG STOP SEQUENCE RUN
NC-CB3-KJ5097.S11
BURNER NG FAILURE
.S4 BMS2 STATUS
CNCG B NG FAILURE CONTROL
SEQ-28.06 CNCGB NG burner failure
DCS DI
STEP S11
BMS2 DO
C
3s
OPERATOR STOP
.S2 BMS2
CNCG B NG OPERATOR CONTROL
1
3s
LOCAL STOP STOP COMMAND
252-LCP-150.PB09.S1 BMS2 .S10 BMS2
CNCG B NG burner stop CNCG B NG OPERATOR CONTROL
SEQ-28.05 CNCGB NG local controls SEQ-28.03 CNCGB NG start sequence
D
NC-CB3-KJ5097.I1
ALWAYS STATUS
A-MODE.
FAILURE RESET
PROT AON REL DCS DI
.S10 BMS2 1
STEP I1
CNCGB FAILURE RESET OPR
SEQ-28.70 CNCGB Common local controls INIT CNCG B NG STOP SEQUENCE BMS2 DO RUNNING
STEP .S12 BMS2
SEQ COMPLETED INT-28.27 Oil burner start conditions
57 SEQ-28.03 CNCGB NG start sequence
From page: 3 SEQ-28.05 CNCGB NG local controls
SEQ-28.06 CNCGB NG burner failure E
STEP 51
PRELIMINARY
CNCGB NG STOP SEQUENCE
Pos. 1
Doc ID: P00592320
0 1 2 3 4 5 6 7
A
STEP STOP
CLOSE GAS VALVES

AUTO CLOSE
51 1s s
CLOSED LIMIT & NOT FAILURE SEQ-28.11 CNCGB NG valves

252-HSV-814.S12 BMS2
B
AUTO CLOSE
252-HSV-815
&
252-HSV-815.S12 BMS2 252-PIC-835.S2
S2 STEP
CNCG B natural gas valve 2 CLOSE TO 0% AND TO M-MODE
SEQ-28.11 CNCGB NG valves BMS2 DO DI DCS 252-PIC-835.S2
OPEN VENT VALVE
AUTO OPEN
C
52 1s s
OPEN LIMIT & NOT FAILURE

252-HSV-830.S11 BMS2
STOP IGNITER
AUTO STOP
WAITING TIME MONITORING TIME ACTION 252-BX-804
53 1s s
CNCG B igniter
SEQ-28.09 CNCGB Igniter D
IGNITER FLAME ON
252-BX-804.S1 BMS2
CNCG B igniter
STEP 54
PRELIMINARY
Pos. 2
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP 53
IGNITER CYLINDER OUT

AUTO OUT
A

54 1s s
OUT POSITION LIMIT

252-HSV-811.ZSO BMS2
GAS LANCE OUT

AUTO OUT
55 1s s
C
OUT POSITION & NOT FAILURE

252-HSV-812.S12 BMS2
START LEAKAGE TEST

START LEAKAGE TEST
WAITING TIME MONITORING TIME ACTION .S56
56 1s s
SEQ-28.12 CNCGB NG leakage test sequence D
READY
SEQ COMPLETED
WAITING TIME MONITORING TIME ACTION 57
Into page: 1
57 s s
E
PRELIMINARY
Pos. 3
Doc ID: P00592320
0 1 2 3 4 5 6 7
This document is the exclusive intellectual property of Metso Power AB/Metso Power Oy/Metso Paper USA, Inc./Metso Paper Sulamericana Ltda and is furnished for the sole purpose of operating and maintaining of the specific project,
CNCG B NG CNCG B LAMP

and re-use of the document for any other project or purpose is prohibited. The document or the information shall not be reproduced or copied, or disclosed to a third party without prior written consent of the company.
BURNER START LOCAL START TEST LAMP TEST ON
ON
ON
252-LCP-150.PB08.S1 BMS2 252-LCP-150.PB01.S1 BMS2
PUSH-BUTTON CNCG B NG burner start PUSH-BUTTON CNCG B lamp test
NO 252-43-150.PB08 NO 252-43-150.PB01
SEQ-28.03 CNCGB NG start sequence SEQ-28.43 CNCGB CNCG local controls
SEQ-30.13 CNCGB Local controls MeOH
CNCG B READY
READY TO START 1 FOR START NG
.S1 BMS2
CNCG B NG
NOT ON
BURNER STOP LOCAL STOP CNCG B NG START SEQUENCE

252-43-150.XL10 B
252-LCP-150.PB09.S1 BMS2 SEQ-28.03 CNCGB NG start sequence
PUSH-BUTTON CNCG B NG burner stop PILOT LAMP
NC 252-43-150.PB09 SEQ-28.04 CNCGB NG stop sequence
CNCG B RUNNING NG
.S1 BMS2
CNCG B FLAME MONITORING &
C
RUNNING
.S11 BMS2
CNCG B NG START SEQUENCE
SEQ-28.03 CNCGB NG start sequence
CNCG B NG BURNER
1
©Metso Power AB or ©Metso Power Oy or ©Metso Paper USA, Inc. or ©Metso Paper Sulamericana Ltda.
RUNNING 1 ON
.S12 BMS2
252-43-150.XL11
PILOT LAMP
&
2 Hz
BURNER NG FAILURE CNCG B NG BURNER

.S4 BMS2
CNCG B NG FAILURE CONTROL & 1 FAILURE
252-43-150.XL12
2 Hz PILOT LAMP
PRELIMINARY
Rev. Designed by Checked by Approved by Project: 110374 Planta Arauco CNCG Drawn 6/27/2018/ATVAKI2 Design TREVESSAPA Rev.
2 8/31/2018/TREVESSAPA 8/31/2018/FTAMJNS 8/31/2018/FTAMSRE Page:
CNCGB NG LOCAL CONTROLS Cust. Doc. ID:
3 5/29/2020/TREJARVEJO 5/29/2020/FTAMJNS 5/29/2020/FTAMSRE
Pos.
SEQ-28.05
Doc. ID: P00592320
0 1 2 3 4 5 6 7
CNCG B NG STARTING CNCG B NG BURNER

NC-CB3-X5064.S2 NC-CB3-X5064.S4
START COND. OK STATUS STATUS A

.S1 BMS2 CNCG B NG OPERATION CNCG B NG STOPPING
CNCG MAIN INTERLOCK NC-CB3-X5064.S1 NC-CB3-X5064.S3
INT-28.11 CNCGB main common interlocks STATUS STATUS
COMB. AIR FAILURE/NG

252-HIC-817 BMS2 DCS DI DCS DI DCS DI DCS DI

BMS2 DO BMS2 DO BMS2 DO BMS2 DO
BURNER IGNITION FAILURE
.S5 BMS2 5s
CNCG B NG INT FIST-OUT CNCG B RUNNING NG
INT-28.12 CNCGB NG interlocks .S1 BMS2
CNCG B FLAME MONITORING
BURNER FLAME FAILURE INT-28.13 CNCGB NG flame monitoring &
.S6 BMS2 S
CNCG B NG INT FIST-OUT
INT-28.12 CNCGB NG interlocks 1 R 1
*)
B
CNCG B FALSE FLAME ON BURNER NG FAILURE
.S2 BMS2 .S4 BMS2
CNCG B FLAME MONITORING RUNNING CNCG B NG FAILURE CONTROL
INT-28.13 CNCGB NG flame monitoring .S11 BMS2 SEQ-28.03 CNCGB NG start sequence
CNCG B NG START SEQUENCE & SEQ-28.04 CNCGB NG stop sequence
VALVE FAILURE S
SEQ-28.03 CNCGB NG start sequence SEQ-28.05 CNCGB NG local controls
252-HSV-814 BMS2 SEQ-28.11 CNCGB NG valves
CNCG B natural gas valve 1 R
INT-28.16 CNCGB burner NG valves SEQ-28.16 CNCGB NG lance
VALVE FAILURE
252-HSV-815 BMS2 RUNNING 10 s
CNCG B natural gas valve 2 .S12 BMS2 BURNER NG FAILURE (PULSED)
CNCG B NG STOP SEQUENCE & .S6 BMS2
INT-28.16 CNCGB burner NG valves S
SEQ-28.04 CNCGB NG stop sequence CNCG B NG FAILURE CONTROL
VALVE FAILURE SEQ-28.08 CNCGB Igniter cylinder
252-HSV-830 BMS2 R
INT-28.16 CNCGB burner NG valves C
FAILURE
252-HSV-811.FLT BMS2 CNCG BURNER ES NOT ON
CNCG B igniter in-out 252-LCP-150.PB02.S1 BMS2 S
SEQ-28.08 CNCGB Igniter cylinder CNCG B emergency stop
INT-28.11 CNCGB main common interlocks R
IGNITER OFF FAILURE

252-BX-804.S5 BMS2 *) NOTE!
CNCG B igniter POP-UP INTERLOCK
INT-28.14 CNCGB igniter WINDOW IS NEEDED
NG VALVES OPEN CMD
.S3 BMS2
CNCG B NG VALVES COMMON &
SEQ-28.11 CNCGB NG valves D
IGNITER ON FAILURE
252-BX-804.S4 BMS2
CNCG B igniter 1
FAILURE
252-HSV-812.FLT BMS2
NG EQUIPMENT IN STOP POS.
.S1 BMS2
CNCG B EQ IN STOP POS
SEQ-28.07 CNCGB NG equipment in stop position
&
FAILURE RESET
.S10 BMS2
SEQ-28.70 CNCGB Common local controls E
PRELIMINARY
CNCGB NG BURNER FAILURE Cust. Doc. ID:
Pos.
SEQ-28.06
Doc. ID: P00592320
0 1 2 3 4 5 6 7
A
CNCG B FLAME SCANNER READY

252-BS-803.S2 BMS2
CNCG BURNER ES NOT ON

252-LCP-150.PB02.S1 BMS2
CNCG B emergency stop
INT-28.11 CNCGB main common interlocks B

252-HSV-814.S12 BMS2

252-HSV-815.S12 BMS2
CNCG B natural gas valve 2 NOTE!
SEQ-28.11 CNCGB NG valves POP-UP INTERLOCK
WINDOW IS NEEDED
252-HSV-830.S11 BMS2 &
SEQ-28.11 CNCGB NG valves C
252-BS-803 BMS2
OUT POSITION & NOT FAILURE CNCG B NG EQUIP

252-HSV-812.S12 BMS2
CNCG B natural gas lance in-out NC-CB3-X10039.S1
SEQ-28.16 CNCGB NG lance STATUS
OUT POSITION & NOT FAILURE DCS DI

252-HSV-811.S12 BMS2
BMS2 DO
D
IGNITER FAILURE NG EQUIPMENT IN STOP POS.
252-BX-804.S7 BMS2 .S1 BMS2
CNCG B igniter CNCG B EQ IN STOP POS
SEQ-28.09 CNCGB Igniter SEQ-28.03 CNCGB NG start sequence
PRELIMINARY
CNCGB NG EQUIPMENT IN STOP POSITION Cust. Doc. ID:
Pos.
SEQ-28.07
Doc. ID: P00592320
0 1 2 3 4 5 6 7
IGNITER IN COMMAND CNCG B IGNITER CYLINDER

.S1 BMS2 FAILURE A

CNCGB IGNITER TEST CONTROL 1 252-HSV-811.FLT
SEQ-28.14 CNCGB igniter local control
STATUS
& ALARM
IGNITER &
IN COMMAND DCS DI
BMS2 DO
IGNITER OUT COMMAND FAILURE

.S4 BMS2 252-HSV-811.FLT BMS2
CNCGB IGNITER TEST CONTROL CNCG B igniter in-out
SEQ-28.14 CNCGB igniter local control SEQ-28.06 CNCGB NG burner failure
SEQ-30.14 CNCGB Burner failure MeOH
2s AUTO FAILURE
B
IN
IGNITER INTERLOCKING OK PROT
252-BX-804.S6 BMS2 REL
CNCG B igniter & IN POSITION & NOT FAILURE
CNCG B IGNITER IN 252-HSV-811.S11 BMS2
SEQ-28.09 CNCGB Igniter ->A IN-OUT CNCG B igniter in-out
OUT SEQ-28.03 CNCGB NG start sequence
BURNER NG FAILURE (PULSED) SEQ-28.09 CNCGB Igniter
.S6 BMS2 AUTO 252-HSV-811 SEQ-28.11 CNCGB NG valves
OUT
CNCG B NG FAILURE CONTROL & PROT SEQ-28.14 CNCGB igniter local control
SEQ-28.06 CNCGB NG burner failure REL SEQ-30.11 CNCGB Start sequence MeOH
RESET SEQ-30.12 CNCGB Stop sequence MeOH
OIL&MEOH BURNER NOT RUNNING SEQ-28.04 CNCGB NG stop sequence SEQ-30.16 CNCGB MeoH valves
BMS2
Oil burner running/starting SEQ-30.11 CNCGB Start sequence MeOH
INT-28.27 Oil burner start conditions SEQ-30.12 CNCGB Stop sequence MeOH
OIL START ALLOWED C

.S1 BMS2
Oil burner running/starting &
1
INT-28.27 Oil burner start conditions
& OUT POSITION & NOT FAILURE
252-HSV-811.S12 BMS2
TRIPPED CNCG B igniter in-out
N7:30/4 SEQ-28.03 CNCGB NG start sequence

A3-C000533-252-00-002 A5 SEQ-28.07 CNCGB NG equipment in stop position
SEQ-30.11 CNCGB Start sequence MeOH
SEQ-30.12 CNCGB Stop sequence MeOH
SEQ-30.15 CNCGB Equipment in stop position MeOH
IGNITER
OUT COMMAND
D
OUT POSITION LIMIT
252-HSV-811.ZSO BMS2
MeOH ADDITION OIL&NG BURNER NOT RUNNING CNCG B igniter in-out
BMS2 SEQ-28.04 CNCGB NG stop sequence
Oil burner running/starting
INT-28.27 Oil burner start conditions SEQ-30.14 CNCGB Burner failure MeOH
3
CNCG BURNER FAILURE MEOH &
S6 BMS
CNCG B Failure Control MeOH
SEQ-30.14 CNCGB Burner failure MeOH AUTO
OPEN
PROT
IGNITER/BLOWING OK
.S3 BMS2 REL
CNCG MAIN INTERLOCK CNCG B IGNITER
INT-28.11 CNCGB main common interlocks ->A INSTRUMENT
AIR VALVE
IGNITER FLAME ON
CLOSE
252-BX-804.S1 BMS2
AUTO 252-HSV-816 E
PROT
CNCG B igniter
REL
FAILURE RESET
.S10 BMS2
SEQ-28.70 CNCGB Common local controls PRELIMINARY
CNCGB IGNITER CYLINDER Cust. Doc. ID:
Pos.
SEQ-28.08
Doc. ID: P00592320
0 1 2 3 4 5 6 7
START IGNITER NOTE 1: NOTE 2:

TRANSFORM
LOGIC SPLITTED IN TWO PAGES T1: IGNITER MAX OPERATION
A3-C000533-262-06-001
PAGE 1 A3 SEE INT- 28.14 TIME, DEFAULT 180s
&
A
IGNITER ON COMMAND 1
.S2 BMS2
CNCGB IGNITER TEST CONTROL
OIL START ALLOWED

.S1 BMS2
TRIPPED &
N7:30/4
A3-C000533-252-00-002 A5
IGNITER FLAME ON B
252-BX-804.S1 BMS2
IGNITER OFF COMMAND CNCG B igniter
.S3 BMS2 INT-28.14 CNCGB igniter
OIL SEQUENCE
STOP IGNITER TRANSFORM ON COMMAND
PAGE 1 A6
START
AUTO IGNITER ON COMMAND 252-BX-804.S10 BMS2
PROT FLAME ON CNCG B igniter
1 REL INT-28.14 CNCGB igniter
BURNER NG FAILURE (PULSED) CNCG B IGNITER ON
.S6 BMS2 ->A
CNCG B NG FAILURE CONTROL OFF
& C
Monitoring time in BMS
AUTO 252-BX-804
STOP
PROT On = 10 s
OIL&MEOH BURNER NOT RUNNING
BMS2 REL Off = 20 s
OIL&NG BURNER NOT RUNNING SEQ-30.11 CNCGB Start sequence MeOH

BMS2 SEQ-30.12 CNCGB Stop sequence MeOH
Oil burner running/starting MeOH ADDITION
CNCG BURNER FAILURE MEOH &
S6 BMS
IN POSITION & NOT FAILURE

252-HSV-811.S11 BMS2 D
&
IGNITER/BLOWING OK
.S3 BMS2
CNCG MAIN INTERLOCK
INT-28.11 CNCGB main common interlocks IGNITER INTERLOCKING OK
& 252-BX-804.S6 BMS2
180 s CNCG B igniter
IGNITER FLAME & CONTROL ON SEQ-28.08 CNCGB Igniter cylinder
252-BX-804.S3 BMS2 ON
CNCG B igniter
INT-28.14 CNCGB igniter T1
IGNITER ON FAILURE
252-BX-804.S4 BMS2
CNCG B igniter E
1
IGNITER OFF FAILURE IGNITER FAILURE
252-BX-804.S5 BMS2 252-BX-804.S7 BMS2
CNCG B igniter CNCG B igniter
INT-28.14 CNCGB igniter SEQ-28.07 CNCGB NG equipment in stop position
PRELIMINARY
CNCGB IGNITER Cust. Doc. ID:
Pos.
SEQ-28.09
Doc. ID: P00592320
0 1 2 3 4 5 6 7
IN POSITION & NOT FAILURE NOTE: VALVE FAILURE
252-HSV-811.S11 BMS2 252-HSV-814 BMS2
CNCG B igniter in-out LOGIC SPLITTED IN TWO PAGES CNCG B natural gas valve 1
SEQ-28.08 CNCGB Igniter cylinder SEE INT-28.15 INT-28.16 CNCGB burner NG valves
&
OPEN LIMIT & OPEN LIMIT & NOT FAILURE
IGNITER FLAME & CONTROL ON AUTO OPEN COMMAND ON 252-HSV-814.ZSO BMS2 252-HSV-814.S11 BMS2 A
OPEN
252-BX-804.S3 BMS2 PROT CNCG B natural gas valve 1 CNCG B natural gas valve 1
CNCG B igniter 1
REL INT-28.16 CNCGB burner NG valves SEQ-28.03 CNCGB NG start sequence
INT-28.14 CNCGB igniter SEQ-28.12 CNCGB NG leakage test sequence
CNCG B NATURAL OPEN
->A GAS VALVE 1
CLOSE
CLOSE
AUTO 252-HSV-814 CLOSE LIMIT & CLOSED LIMIT & NOT FAILURE
PROT 252-HSV-814.ZSC BMS2 252-HSV-814.S12 BMS2
REL CNCG B natural gas valve 1 CNCG B natural gas valve 1
INT-28.16 CNCGB burner NG valves SEQ-28.04 CNCGB NG stop sequence
SEQ-28.03 CNCGB NG start sequence SEQ-28.07 CNCGB NG equipment in stop position
SEQ-28.04 CNCGB NG stop sequence OPEN COMMAND ON SEQ-28.12 CNCGB NG leakage test sequence
SEQ-28.12 CNCGB NG leakage test sequence 252-HSV-814.S10 BMS2 SEQ-28.13 CNCGB NG leakage test
INT-28.16 CNCGB burner NG valves
A
BURNER NG FAILURE B
.S4 BMS2
CNCG B NG FAILURE CONTROL & NG VALVES OPEN CMD
.S3 BMS2
SEQ-28.06 CNCGB NG burner failure CNCG B NG VALVES COMMON
&
CNCG B NG VALVES INTERLOCK SEQ-28.15 CNCGB combustion air monitoring
.S1 BMS2
CNCG B NG INTERLOCK OPEN COMMAND ON
252-HSV-815.S10 BMS2
INT-28.12 CNCGB NG interlocks CNCG B natural gas valve 2
VALVE FAILURE
252-HSV-815 BMS2
OPEN LIMIT OPEN LIMIT & NOT FAILURE C

&
AUTO OPEN COMMAND ON 252-HSV-815.ZSO BMS2 252-HSV-815.S11 BMS2
OPEN
PROT CNCG B natural gas valve 2 CNCG B natural gas valve 2
REL INT-28.16 CNCGB burner NG valves SEQ-28.03 CNCGB NG start sequence
CNCG B NATURAL SEQ-28.12 CNCGB NG leakage test sequence
OPEN
->A GAS VALVE 2
A CLOSE
&
CLOSE
1 AUTO 252-HSV-815 CLOSE LIMIT & CLOSED LIMIT & NOT FAILURE
B PROT 252-HSV-815.ZSC BMS2 252-HSV-815.S12 BMS2
REL CNCG B natural gas valve 2 CNCG B natural gas valve 2
INT-28.16 CNCGB burner NG valves SEQ-28.04 CNCGB NG stop sequence
SEQ-28.03 CNCGB NG start sequence SEQ-28.07 CNCGB NG equipment in stop position
SEQ-28.04 CNCGB NG stop sequence SEQ-28.12 CNCGB NG leakage test sequence
SEQ-28.12 CNCGB NG leakage test sequence SEQ-28.13 CNCGB NG leakage test
VALVE FAILURE D
252-HSV-830 BMS2
& 1 CNCG B natural gas vent valve
5s OPEN LIMIT & OPEN LIMIT & NOT FAILURE

252-HSV-830.ZSO BMS2 252-HSV-830.S11 BMS2
OFF CNCG B natural gas vent valve CNCG B natural gas vent valve
LEAKAGE TEST RUNNING AUTO
OPEN
& 1 INT-28.16 CNCGB burner NG valves SEQ-28.04 CNCGB NG stop sequence

.S1 BMS2 PROT
CNCG B LEAK TEST MONITOR REL SEQ-28.07 CNCGB NG equipment in stop position
INT-28.16 CNCGB burner NG valves SEQ-28.12 CNCGB NG leakage test sequence
CNCG B NATURAL OPEN SEQ-28.13 CNCGB NG leakage test
->A GAS VENT VALVE
CLOSE
B
CLOSE
AUTO 252-HSV-830
PROT
REL CLOSE COMMAND ON
CLOSE LIMIT & CLOSED LIMIT & NOT FAILURE
SEQ-28.03 CNCGB NG start sequence 252-HSV-830.ZSC BMS2 252-HSV-830.S12 BMS2 E
SEQ-28.04 CNCGB NG stop sequence CNCG B natural gas vent valve CNCG B natural gas vent valve
SEQ-28.12 CNCGB NG leakage test sequence INT-28.16 CNCGB burner NG valves SEQ-28.03 CNCGB NG start sequence
CLOSE COMMAND ON
252-HSV-830.S10 BMS2
PRELIMINARY
CNCGB NG VALVES Cust. Doc. ID:
Pos.
SEQ-28.11
Doc. ID: P00592320
0 1 2 3 4 5 6 7
IN STOP POSITION
.S1
CNCG B EQUIPMENT/LEAK TEST A

RUNNING
.S11 BMS2
RUNNING
.S12 BMS2
CNCG B NG STOP SEQUENCE 1
&
252-LCP-150.PB02.S1 BMS2 B
P> MIN1 CNCG B emergency stop
252-PI-834 BMS2 INT-28.11 CNCGB main common interlocks CNCG B LEAKAGE TEST READY CNCG B LEAKAGE TEST RUNNING
NC-CB3-KJ5093.S1 NC-CB3-KJ5093.S11
INT-28.12 CNCGB NG interlocks STATUS STATUS
ES NOT PUSHED
BMS2 DCS DI DCS DI
Natural gas emergency stop
INT-28.12 CNCGB NG interlocks BMS2 DO BMS2 DO
C
3s
START LEAKAGE TEST
.S56
SEQ-28.04 CNCGB NG stop sequence NC-CB3-H10038.S1 3s 1 RUNNING
S1 STEP
.S11
CNCG B LEAKAGE START DCS DO NC-CB3-H10038.S2
DI BMS2 CNCG B NG LEAKAGE TEST SEQ
S2 STEP
TEST CONTROL CNT-28.01 CNCG burner NG flow and pressure

OPERATOR STOP DCS DO DI BMS2 3s
D
3s
1
NC-CB3-KJ5093.I1
STATUS
ALWAYS
LOCAL STOP
TO STOP STEP A-MODE.
252-LCP-150.PB09.S1 BMS2 1
Into page: 5
CNCG B NG burner stop PROT AON REL DCS DI
SEQ-28.05 CNCGB NG local controls STEP I1INTEGER
1 INIT CNCG B NG LEAKAGE TEST SEQUENCE BMS2 DO

FAILURE RESET
FAILURE
.S10 BMS2 STEP
.S3
CNCG B LEAK TEST FAILURE E
SEQ-28.70 CNCGB Common local controls RUNNING
.S11 BMS2
SEQ COMPLETED CNCG B NG LEAKAGE TEST SEQ
13
From page: 5 INT-28.16 CNCGB burner NG valves
STEP 1 SEQ-28.04 CNCGB NG stop sequence
SEQ-28.13 CNCGB NG PRELIMINARY
leakage test
CNCGB NG LEAKAGE TEST SEQUENCE
Pos. 1
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP START
OPEN GAS VALVE 2

AUTO OPEN
A

1 1s s

252-HSV-815.S11 BMS2
CLOSE GAS VALVE 2

AUTO CLOSE B
2 1s s

252-HSV-815.S12 BMS2
PRESSURE TO MEMORY
COPY PRESSURE TO MEMORY
WAITING TIME MONITORING TIME ACTION 252-PI-837.S1 BMS2 C
3 5s 10s
CNCG B natural gas Pressure (leak test)
FAILURE CNT-28.01 CNCG burner NG flow and pressure
P > MIN 2
252-PI-837.L2 BMS2
SEQ-28.13 CNCGB NG leakage test TO FAILURE STEP
3
Into page: 4
NOT ATMOSPHERE PRESSURE D

.S2
CNCG B NG LEAKAGE TEST SEQ
CLOSE VENT VALVE
AUTO CLOSE
4 5s s

252-HSV-830.S12 BMS2 E
STEP 5 PRELIMINARY
Pos. 2
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP 4
TESTING VALVE 1

A
5 VLV 1 LEAK FAILURE
20s 25s
FAILURE .F5
P < MAX 1 (CALC)

TO STOP STEP
252-PI-837.H1 BMS2 5
Into page: 5
OPEN GAS VALVE 1
AUTO OPEN

6 1s 15s
CNCG B natural gas valve 1 B
FAILURE SEQ-28.11 CNCGB NG valves
252-HSV-814.S11 BMS2
& COPY PRESSURE TO MEMORY
252-PI-837.S2 BMS2
&
P < MAX 2
252-PI-837.H2 BMS2
CNCG B natural gas Pressure (leak test) TO FAILURE STEP
6
SEQ-28.13 CNCGB NG leakage test Into page: 4
CNCG B TEST PRESSURE FAILURE C

.S1
CLOSE GAS VALVE 1
AUTO CLOSE
CLOSED LIMIT & NOT FAILURE WAITING TIME MONITORING TIME ACTION 252-HSV-814
252-HSV-814.S12 BMS2 7 1s s
CNCG B natural gas valve 1 SEQ-28.11 CNCGB NG valves
&
20 %
252-PIC-835.S1
Output > MAX 19 % D
252-FIC-805
TESTING GAS VALVE 2 & VENT VALVE

8 20s 25s
VLV 2 OR VENT LEAK FAILURE
FAILURE .F8
P > MIN 1 (CALC)

TO STOP STEP
252-PI-837.L1 BMS2 8 E
Into page: 5
STEP 9 PRELIMINARY
Pos. 3
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP 8
OPEN VENT VALVE

AUTO OPEN A

9 1s s

252-HSV-830.S11 BMS2
LEAK TEST COMPLETE B

LEAKAGE TEST OK
WAITING TIME MONITORING TIME ACTION .S10
10 1s s
TO END STEP
10
Into page: 5
TO FAILURE STEP
3
From page: 2
TO FAILURE STEP
6
From page: 3
D
FAILURE STEP
LEAK TEST FAILURE
WAITING TIME MONITORING TIME ACTION .F11
11 s s
E
STEP 12
PRELIMINARY
Pos. 4
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP 11
TO STOP STEP
1 A
From page: 1
TO STOP STEP
5
From page: 3
TO STOP STEP
8
From page: 3
STOP STEP B
AUTO OPEN
12 1s s
252-HSV-830.S11 BMS2
AUTO CLOSE
252-HSV-814
252-HSV-814.S12 BMS2 &
CNCG B natural gas valve 1 C
AUTO CLOSE
252-HSV-815
252-HSV-815.S12 BMS2
CNCG B natural gas valve 2 RESET
SEQ-28.11 CNCGB NG valves 252-PIC-835.S11
TO END STEP
10 D
From page: 4
READY
SEQ COMPLETED
Into page: 1
13 s s
PRELIMINARY
Pos. 5
Doc ID: P00592320
0 1 2 3 4 5 6 7
VALVE FAILURE
252-HSV-814 BMS2
4s A
VALVE FAILURE LEAKAGE TEST OK VALID
252-HSV-815 BMS2 1 .S10 S .S1 BMS2
CNCG B natural gas valve 2 CNCG B NG LEAKAGE TEST SEQ .T2 CNCG B LEAKAGE TEST
INT-28.16 CNCGB burner NG valves SEQ-28.12 CNCGB NG leakage test sequence 2s R TIME RUNNING DOWN IN DCS DISPLAY SEQ-28.03 CNCGB NG start sequence
CNCG B LEAKAGE TEST TIME XX d ; XX h
EXCEEDED CNCG B LEAKAGE TEST

VALVE FAILURE NC-CB3-X5096.S2 COUNTER
252-HSV-830 BMS2 NC-CB3-X5096.S1
CNCG B natural gas vent valve STATUS STATUS
INT-28.16 CNCGB burner NG valves & ALARM
1 DCS AI
DCS DI INTEGER DCS DI

BMS2 AO
CNCG B NOT ATMOSPHERE PRESSURE BMS2 DO BMS2 DO
FAILURE ON
NC-CB3-X5095.S4
B
NOT ATMOSPHERE PRESSURE STATUS
.S2 S BMS2 DO DI DCS 30 d
CNCG B NG LEAKAGE TEST SEQ & ALARM
SEQ-28.12 CNCGB NG leakage test sequence R CNCG B TEST PRESSURE
LOW PRESSURE
NC-CB3-X5095.S5
CNCG B TEST PRESSURE FAILURE STATUS
.S1 S BMS2 DO DI DCS
SEQ-28.12 CNCGB NG leakage test sequence R
CNCG B GAS VALVE 2 OR VENT VALVE
LEAKING FAIL
NC-CB3-X5095.S1
VLV 2 OR VENT LEAK FAILURE STATUS
.F8 S BMS2 DO DI DCS
SEQ-28.12 CNCGB NG leakage test sequence R CNCG B GAS VALVE 1 C
LEAKING FAIL
NC-CB3-X5095.S2
VLV 1 LEAK FAILURE STATUS
.F5 S BMS2 DO DI DCS
SEQ-28.12 CNCGB NG leakage test sequence R
CNCG B LEAKAGE TEST

FAILURE
NC-CB3-X5095.S3
RUNNING STATUS
BMS2 DO DI DCS
.S11 BMS2 & ALARM
&
LEAK TEST FAILURE 1 FAILURE CNCG B NATURAL D
.F11 S .S3 GAS PRESSURE (LEAK
CNCG B NG LEAKAGE TEST SEQ CNCG B LEAK TEST FAILURE TEST)
SEQ-28.12 CNCGB NG leakage test sequence R SEQ-28.12 CNCGB NG leakage test sequence 252-PI-837 P < MAX 2
P< MAX2 bar(g) 252-PI-837.H2 BMS2
P> MIN2 bar(g) CNCG B natural gas Pressure (leak test)
CALCULATED LIMIT VALUES SEQ-28.12 CNCGB NG leakage test sequence
252-HSV-814.S12 BMS2 CNCG B EQUIPMENT/LEAK TEST P< MAX1 bar(g)
CNCG B natural gas valve 1 NC-CB3-X5094.S1 P > MIN 2
P> MIN1 bar(g)
SEQ-28.11 CNCGB NG valves 252-PI-837.L2 BMS2
STATUS CNT-28.01 CNCG burner NG flow and pressure CNCG B natural gas Pressure (leak test)
252-HSV-815.S12 BMS2 &
CNCG B natural gas valve 2 DCS DI
P < MAX 1 (CALC)
SEQ-28.11 CNCGB NG valves 252-PI-837.H1 BMS2
BMS2 DO
OPEN LIMIT & NOT FAILURE IN STOP POSITION
252-HSV-830.S11 BMS2 .S1 E
CNCG B natural gas vent valve CNCG B EQUIPMENT/LEAK TEST P > MIN 1 (CALC)
SEQ-28.11 CNCGB NG valves SEQ-28.12 CNCGB NG leakage test sequence 252-PI-837.L1 BMS2
FAILURE RESET &
.S10 BMS2
SEQ-28.70 CNCGB Common local controls PRELIMINARY
CNCGB NG LEAKAGE TEST Cust. Doc. ID:
Pos.
SEQ-28.13
Doc. ID: P00592320
0 1 2 3 4 5 6 7
3s
PUSHED
252-LCP-150.PB05.S1 BMS2 A
CNCG B igniter start
IGNITION GAS PRESSURE OK

.S1 BMS2 &
NG PRESSURE TO IGNITERS
INT-28.26 CNCGB CNCG burner status
1s
IGNITER IN COMMAND
S .S1 BMS2
R SEQ-28.08 CNCGB Igniter cylinder
IGNITER INTERLOCKING OK 1s B
252-BX-804.S6 BMS2
CNCG B igniter IN POSITION & NOT FAILURE & IGNITER ON COMMAND
1 252-HSV-811.S11 BMS2 .S2 BMS2
SEQ-28.09 CNCGB Igniter CNCG B igniter in-out CNCGB IGNITER TEST CONTROL
SEQ-28.08 CNCGB Igniter cylinder SEQ-28.09 CNCGB Igniter
IGNITER FLAME & CONTROL ON

252-BX-804.S3 BMS2
CNCG B igniter &
30 s
ON
C
1s
3s 1s
PUSHED 1 IGNITER OFF COMMAND

252-LCP-150.PB06.S1 BMS2 S .S3 BMS2
CNCG B igniter stop CNCGB IGNITER TEST CONTROL
SEQ-28.70 CNCGB Common local controls R SEQ-28.09 CNCGB Igniter
5s 1s
& IGNITER OUT COMMAND
OUT POSITION LIMIT ON .S4 BMS2
252-HSV-811.ZSO BMS2 CNCGB IGNITER TEST CONTROL
CNCG B igniter in-out & 1
D
30 s
ON
IGNITER FLAME ON
252-BX-804.S1 BMS2
CNCG B igniter
PRELIMINARY
CNCGB IGNITER LOCAL CONTROL Cust. Doc. ID:
Pos.
SEQ-28.14
Doc. ID: P00592320
0 1 2 3 4 5 6 7
NG VALVES OPEN CMD
.S3 BMS2
CNCG B NG VALVES COMMON
1
RUNNING
.S12 BMS2 A
3 MEOH ADDITION
AIR DAMPER NOT CLOSED
252-HIC-817.S1 BMS2
CNCG Comb.air damper open CNCG B COMBUSTION AIR (NG)
INT-28.11 CNCGB main common interlocks FAILURE
& 252-HIC-817.S1
IN AUTO MODE & STATUS
252-HIC-817 BMS2 & ALARM
DCS DI
B
BMS2 DO
20 s
SET MONITORING ON COMB. AIR FAILURE/NG
ON
252-HIC-817 BMS2 S S 252-HIC-817 BMS2
CNCG B combustion air damper CNCG B combustion air damper
2s
SEQ-28.03 CNCGB NG start sequence R R SEQ-28.06 CNCGB NG burner failure
2s
1
BURNER NG FAILURE
.S4 BMS2
CNCG B NG FAILURE CONTROL
C
FAILURE RESET
.S10 BMS2
3
CNCGB MEOH VALVES OPEN CMD
S3 BMS
CNCG B MeOH Valves Common MEOH ADDITION

SEQ-30.16 CNCGB MeoH valves
1
SHUT-DOWN PROGRAM RUN
S1
CNCG B MeOH Stop Sequence
CNCGB COMBUSTION AIR (MEOH)
FAILURE
252-HIC-817.S4
D
STATUS
& ALARM
&
DCS RB DI
BMS RB DO
20 s
SET MONITORING ON (MEOH) COMB. AIR FAILURE (MEOH)
ON
252-HIC-817S12 BMS S S 252-HIC-817.S4 BMS
CNCG B combustion air damper CNCG B combustion air damper
2s
SEQ-30.12 CNCGB Stop sequence MeOH R R SEQ-30.14 CNCGB Burner failure MeOH
2s E
1
CNCG BURNER FAILURE MEOH

S6 BMS
PRELIMINARY
CNCGB COMBUSTION AIR MONITORING Cust. Doc. ID:
Pos.
SEQ-28.15
Doc. ID: P00592320
0 1 2 3 4 5 6 7
GAS LANCE IN A
252-ZS-808.ZSI BMS2
CNCG B natural gas lance in position
INT-28.12 CNCGB NG interlocks
CNCG B GAS LANCE

5s FAILURE
BURNER NG FAILURE 252-HSV-812.FLT
ON
.S4 BMS2 S
CNCG B NG FAILURE CONTROL STATUS B
SEQ-28.06 CNCGB NG burner failure R & ALARM
DCS DI
BMS2 DO
FAILURE
252-HSV-812.FLT BMS2
AUTO FAILURE
IN
PROT
REL IN POSITION & NOT FAILURE
&
->A
CNCG B NATURAL IN 252-HSV-812.S11 BMS2 C
CLOSE LIMIT GAS LANCE IN-OUT CNCG B natural gas lance in-out
252-HSV-814.ZSC BMS2 SEQ-28.03 CNCGB NG start sequence
CNCG B natural gas valve 1 OUT
INT-28.16 CNCGB burner NG valves 1 AUTO 252-HSV-812
OUT
CLOSE LIMIT PROT
252-HSV-815.ZSC BMS2 REL
CNCG B natural gas valve 2 RESET

INT-28.16 CNCGB burner NG valves SEQ-28.03 CNCGB NG start sequence
FAILURE RESET
.S10 BMS2
& OUT POSITION & NOT FAILURE
252-HSV-812.S12 BMS2 D
SEQ-28.07 CNCGB NG equipment in stop position
PRELIMINARY
CNCGB NG LANCE Cust. Doc. ID:
Pos.
SEQ-28.16
Doc. ID: P00592320
0 1 2 3 4 5 6 7
A
CNCG B CNCG INTERLOCK OK

.S1 BMS2
CNCG B CNCG INTERLOCK
INT-28.21 CNCGB CNCG interlocks
CNCG EQUIP. IN STOP POS.
.S1 BMS2
CNCG B CNCG EQ IN STOP POS
SEQ-28.45 CNCGB CNCG equipment in stop pos

NOT ANY BURNER STARTING
.S1 BMS2 B
BURNERS STARTING STATUS
INT-28.26 CNCGB CNCG burner status &
.S12
CNCG B CNCG STOP SEQUENCE
SEQ-28.42 CNCGB CNCG stop sequence CNCG B CNCG START READY
SSO VALVES OPEN NC-CB3-KJ10006.S4
.S8 BMS2
STATUS
CNCG B CNCG valves common
ON (60S)
.S2 BMS2 DCS DI
STEP S4 C
CNCG SUPPORT BURNING ON
INT-28.25 CNCGB support fuel status BMS2 DO
CNCG B CNCG FAILURE READY TO START CNCG
.S4 BMS2 .S4 BMS2
CNCG B CNCG BURNER FAILURE CNCG B CNCG START SEQUENCE
SEQ-28.44 CNCGB CNCG burner failure 3s SEQ-28.43 CNCGB CNCG local controls
NC-CB3-H5098.S1
S1 STEP
CNCG B CNCG START DCS DO NC-CB3-H5098.S2

DI BMS2
3s
S2 STEP
OPR CONTROL OPERATOR STOP

STOP DCS DO DI BMS2 .S1 BMS2
CNCG B CNCG OPR CONTROL D
ALWAYS SEQ-28.42 CNCGB CNCG stop sequence
M-MODE CNCG B CNCG START SEQUENCE RUN
NC-CB3-KJ10006.S11
PROT ->M MON REL
STATUS
STARTING FAILURE CNCG B CNCG START SEQUENCE
.S2 BMS2
INIT DCS DI
CNCG B CNCG BURNER FAILURE
STEP S11
SEQ-28.44 CNCGB CNCG burner failure
3s BMS2 DO
START-UP PROGRAM RUN
SEQ COMPLETED
6 1 .S11
From page: 3
CNCG B CNCG START SEQUENCE
E
SEQ-28.43 CNCGB CNCG local controls
SEQ-28.48 CNCGB CNCG lance pressure monitoring
STEP 1 PRELIMINARY
STEP S11
CNCGB CNCG START SEQUENCE
Pos. 1
Doc ID: P00592320
0 1 2 3 4 5 6 7
A
STEP START
FLUSHING ON
SET FLUSH POSITION
WAITING TIME MONITORING TIME ACTION 252-PIC-846B.S1 BMS2
1 1s s
LP Steam to CNCG RB2 burner
CNT-28.12 CNCG pressure to CNCG burner
CONTROLLER IN AUTO MODE B

252-PIC-846B.S8 BMS2
CONTROLLER IN AUTO MODE

252-PIC-846.S6 BMS2 FLUSHING TIME
CNCG pressure to CNCG burner
SEQ-28.48 CNCGB CNCG lance pressure monitoring WAITING TIME MONITORING TIME ACTION
2 10s s
252-PIC-846B.S8
S8 STEP

252-PIC-846B DCS DO DI BMS2
FLUSHING OFF
RESET FLUSH POSITION
&
252-PIC-846.S6
3 LP Steam to CNCG RB2 burner
S6 STEP
CONTROLLER IN AUTO MODE 10s s

252-PIC-846 DCS DO DI BMS2 252-PIC-846B.S7
D
S7 STEP
CNCG pressure to CNCG burner AUTO MODE ON
BMS2 DO DI DCS 252-PIC-846B
& LP Steam to CNCG RB2 burner
OK 252-PIC-846.S5 INT-28.23 CNCG pressure to burner
S5 STEP
252-PIC-846.S10 BMS2 AUTO MODE ON
CNCG pressure to CNCG burner BMS2 DO DI DCS 252-PIC-846
INT-28.23 CNCG pressure to burner CNCG pressure to CNCG burner
INT-28.23 CNCG pressure to burner
SET MONITORING ON
LP Steam to CNCG RB2 burner E
STEP 4
PRELIMINARY
Pos. 2
Doc ID: P00592320
0 1 2 3 4 5 6 7
STEP 3 A
AUTO CLOSE
CLOSE CNCG VENT VALVE 252-HSV-879
CNCG RB2 vent valve 1
WAITING TIME MONITORING TIME ACTION SEQ-28.46 CNCGB CNCG valves
4 3s s
SET FLUSHING BIT ON
.S5 BMS2
SEQ-28.42 CNCGB CNCG stop sequence
CLOSED LIMIT & NOT FAILURE B

252-HSV-879.S12 BMS2
SEQ-28.46 CNCGB CNCG valves
OPEN CNCG VALVES 252-HIC-878.S3
S3 STEP
RAMP UPWARDS
WAITING TIME MONITORING TIME ACTION BMS2 DO DI DCS 252-HIC-878.S3
5 3s s
CNCG valve 2 to CNCG RB2 burner
AUTO OPEN C
252-HSV-880
NOT CLOSED & NOT FAILURE

252-HIC-878.S22 BMS2
CNCG valve 2 to CNCG RB2 burner &
252-HSV-880.S11 BMS2
CNCG valve 3 to CNCG RB2 burner D
READY
SEQ COMPLETED
Into page: 1
6 s s
E
PRELIMINARY
Pos. 3
Doc ID: P00592320
0 1 2 3 4 5 6 7
IGNITER/BLOWING OK
.S3 BMS2
CNCG MAIN INTERLOCK
A
BOILER MAIN INTERLOCK OK

BMS2
Boiler main interlock OK CNCG B CNCG STOP READY
NC-CB3-KJ10007.S4
INT-26.11 Chipbin gases common interlocks
CNCG BURNER ES NOT ON & STATUS
252-LCP-150.PB02.S1 BMS2
IN POSITION
DCS DI
252-ZS-810 BMS2 STEP S4
CNCG burner lance limit switch B
BMS2 DO
3s
OPERATOR STOP
.S1 BMS2
CNCG B CNCG OPR CONTROL
SEQ-28.41 CNCGB CNCG start sequence 3s 1
OPERATION FAILURE
.S1 BMS2
CNCG B CNCG BURNER FAILURE C
SEQ-28.44 CNCGB CNCG burner failure & CNCG B CNCG GAS IN PIPE
SET FLUSHING BIT ON NC-CB3-KJ10006.S1
.S5 BMS2 S
STATUS
SEQ-28.41 CNCGB CNCG start sequence R SEQUENCE STEP NUMBER
DCS DI
NC-CB3-KJ10007.I1
STEP S1
STATUS CNCG B CNCG STOP SEQUENCE RUN
BMS2 DO NC-CB3-KJ10007.S12
FAILURE RESET
.S10 BMS2 STATUS
CNCGB FAILURE RESET OPR DCS DI
SEQ-28.70 CNCGB Common local controls STEP INTEGER
I1 D
3s PROT ->M MON REL
ALWAYS
STOPPING FAILURE BMS2 DO
.S3 BMS2 ON 1
M-MODE DCS DI
CNCG B CNCG STOP SEQUENCE STEP S12
SEQ-28.44 CNCGB CNCG burner failure INIT STEP BMS2 DO
3s SHUT-DOWN PROGRAM RUN
SEQ COMPLETED .S12
57
From page: 3 CNCG B CNCG STOP SEQUENCE
SEQ-28.41 CNCGB CNCG start sequence
SEQ-28.43 CNCGB CNCG local controls
VALVE FAILURE 1 &
JUMP TO STEP 56 E
.S5 BMS2 50
Into page: 3
STEP 51 PRELIMINARY
CNCGB CNCG STOP SEQUENCE
Pos. 1
Doc ID: P00592320
0 1 2 3 4 5 6 7
A
STEP START
CNCG VALVE 1 CLOSE 252-HIC-878.S4
S4 STEP
RAMP DOWNWADS
WAITING TIME MONITORING TIME ACTION BMS2 DO DI DCS 252-HIC-878.S4
51 1s s

252-HIC-878.S12 BMS2
B
CNCG VALVE 2 CLOSE
AUTO CLOSE
52 1s s

252-HSV-880.S12 BMS2
CNCG VENT VALVE OPEN
C
AUTO OPEN
53 1s s

252-HSV-879.S11 BMS2
FLUSHING ON
SET FLUSH POSITION
D
54 1s s
FLUSHING TIME

55 20s s
STEP 56
PRELIMINARY
Pos. 2
Doc ID: P00592320
0 1 2 3 4 5 6 7
A
STEP 55
JUMP TO STEP 56
50
From page: 1
FLUSHING OFF B
RESET FLUSH POSITION
56 1s s
S7 STEP
MAN MODE ON
BMS2 DO DI DCS 252-PIC-846B
HEATING POSITION
LP Steam to CNCG RB2 burner C
S8 STEP
MAN MODE ON
BMS2 DO DI DCS 252-PIC-846
252-PIC-846.S3 INT-28.23 CNCG pressure to burner
S3 STEP
S6 STEP
OPEN TO 100%
BMS2 DO DI DCS 252-PIC-846.S3 DCS
D
READY
SEQ COMPLETED
Into page: 1
57 s s
PRELIMINARY
Pos. 3
Doc ID: P00592320
0 1 2 3 4 5 6 7
LAMP TEST ON
252-LCP-150.PB01.S1 BMS2
CNCG B lamp test
SEQ-28.05 CNCGB NG local controls
CNCG B READY
READY TO START CNCG 1 FOR START CNCG
.S4 BMS2
252-43-150.XL14
PILOT LAMP
B
SSO VALVES OPEN

.S8 BMS2
CNCG B CNCG valves common &
C
.S12
CNCG B CNCG STOP SEQUENCE
1 CNCG B CNCG
START-UP PROGRAM RUN 1 BURNER ON

.S11
252-43-150.XL15
PILOT LAMP
&
2 Hz
CNCG B CNCG FAILURE

.S4 BMS2 CNCG B CNCG
CNCG B CNCG BURNER FAILURE & 1 BURNER FAILURE
252-43-150.XL16
2 Hz PILOT LAMP
PRELIMINARY
CNCGB CNCG LOCAL CONTROLS Cust. Doc. ID:
Pos.
SEQ-28.43
Doc. ID: P00592320
0 1 2 3 4 5 6 7
CNCG B CNCG OPERATION

NC-CB3-X10017.S1 A
STATUS CNCG B CNCG STARTING
NC-CB3-X10017.S2
STATUS CNCG B CNCG STOPPING
NC-CB3-X10017.S3
CNCG B CNCG INTERLOCK OK STATUS

CNCG B CNCG BURNER
.S1 BMS2
CNCG B CNCG INTERLOCK NC-CB3-X10017.S4
INT-28.21 CNCGB CNCG interlocks STATUS
DCS DI DCS DI DCS DI
VALVE FAILURE CNCG B CNCG FAILURE
252-HIC-878 BMS2 .S4
CNCG valve 2 to CNCG RB2 burner CNCG B CNCG BURNER FAILURE
BMS2 DO BMS2 DO BMS2 DO
INT-28.24 CNCGB CNCG valves 5s INT-28.23 CNCG pressure to burner
SSO VALVES OPEN DCS DI B
.S8 BMS2
VALVE FAILURE CNCG B CNCG valves common &
252-HSV-880 BMS2 1 S
CNCG valve 3 to CNCG RB2 burner INT-28.26 CNCGB CNCG burner status BMS2 DO
INT-28.24 CNCGB CNCG valves R 1
CNCG B CNCG FAILURE
.S4 BMS2
VALVE FAILURE CNCG B CNCG BURNER FAILURE
252-HSV-879 BMS2 START-UP PROGRAM RUN
CNCG RB2 vent valve 1 .S11 CNT-28.12 CNCG pressure to CNCG burner
CNCG B CNCG START SEQUENCE & SEQ-28.41 CNCGB CNCG start sequence
INT-28.24 CNCGB CNCG valves S
SEQ-28.41 CNCGB CNCG start sequence SEQ-28.43 CNCGB CNCG local controls
R SEQ-28.46 CNCGB CNCG valves
PRESSURE FAILURE SEQ-28.48 CNCGB CNCG lance pressure monitoring
.S6 BMS2
SEQ-28.48 CNCGB CNCG lance pressure monitoring SHUT-DOWN PROGRAM RUN
.S12
CNCG B CNCG STOP SEQUENCE &
S C
R

252-LCP-150.PB02.S1 BMS2 S
INT-28.11 CNCGB main common interlocks R
FAILURE RESET
.S10 BMS2
CNCGB FAILURE RESET OPR STOPPING FAILURE D
SEQ-28.70 CNCGB Common local controls .S3 BMS2
& CNCG B CNCG BURNER FAILURE
CNCG EQUIP. IN STOP POS.
.S1 BMS2 STARTING FAILURE
CNCG B CNCG EQ IN STOP POS .S2 BMS2
SEQ-28.45 CNCGB CNCG equipment in stop pos CNCG B CNCG BURNER FAILURE
OPERATION FAILURE
VALVE FAILURE .S1 BMS2
.S5 CNCG B CNCG BURNER FAILURE
DCS DI
NC-CB3-X10017.S5
BMS2 DO
1 VALVE FAILURE E
.S5 BMS2
PRELIMINARY
CNCGB CNCG BURNER FAILURE Cust. Doc. ID:
Pos.
SEQ-28.44
Doc. ID: P00592320
0 1 2 3 4 5 6 7
A
IN POSITION
252-ZS-810 BMS2
CNCG burner lance limit switch
NOTE!
CLOSED LIMIT & NOT FAILURE POP-UP INTERLOCK
252-HIC-878.S12 BMS2 WINDOW IS NEEDED
CNCG B CNCG EQUIP

CLOSED LIMIT & NOT FAILURE NC-CB3-X10018.S1 C
252-HSV-880.S12 BMS2 &
CNCG valve 3 to CNCG RB2 burner STATUS
OPEN LIMIT & NOT FAILURE DCS DI

252-HSV-879.S11 BMS2
BMS2 DO
CNCG BURNER ES NOT ON CNCG EQUIP. IN STOP POS.

252-LCP-150.PB02.S1 BMS2 .S1 BMS2
CNCG B emergency stop CNCG B CNCG EQ IN STOP POS
INT-28.11 CNCGB main common interlocks SEQ-28.41 CNCGB CNCG start sequence
PRELIMINARY
CNCGB CNCG EQUIPMENT IN STOP POS Cust. Doc. ID:
Pos.
SEQ-28.45
Doc. ID: P00592320
0 1 2 3 4 5 6 7
NOTE:
LOGIC SPLITTED IN TWO PAGES
SEE INT-28.24 VALVE FAILURE
252-HIC-878 BMS2
INT-28.24 CNCGB CNCG valves A

ON (60S)
.S2 BMS2
CNCG SUPPORT BURNING ON OPEN LIMIT OPEN LIMIT & NOT FAILURE
&
INT-28.25 CNCGB support fuel status 252-HIC-878.ZSO BMS2 252-HIC-878.S11 BMS2
Output > 3% % CNCG valve 2 to CNCG RB2 burner CNCG valve 2 to CNCG RB2 burner
HIC
INT-28.24 CNCGB CNCG valves

->A CNCG VALVE O
->M 2 TO CNCG
RB2 BURNER C
252-HIC-878
0% [252-HV-878] CLOSE LIMIT CLOSED LIMIT & NOT FAILURE
&
CNT-28.12 CNCG pressure to CNCG burner 252-HIC-878.ZSC BMS2 252-HIC-878.S12 BMS2
CNCG valve 2 to CNCG RB2 burner CNCG valve 2 to CNCG RB2 burner
INT-28.24 CNCGB CNCG valves SEQ-28.42 CNCGB CNCG stop sequence
CNCG B CNCG FAILURE
.S4 BMS2 B
CNCG B CNCG BURNER FAILURE &
SEQ-28.44 CNCGB CNCG burner failure OPEN COMMAND ON & NOT CLOSED & NOT FAILURE
252-HIC-878.S10 BMS2 252-HIC-878.S22 BMS2
CNCG valve 2 to CNCG RB2 burner CNCG valve 2 to CNCG RB2 burner
INT-28.24 CNCGB CNCG valves SEQ-28.41 CNCGB CNCG start sequence
CNCG B CNCG INTERLOCK OK
.S1 BMS2
CNCG B CNCG INTERLOCK & CNCG VALVES OPEN CMD
.S3 BMS2
INT-28.21 CNCGB CNCG interlocks CNCG B CNCG valves common
OPEN COMMAND ON
252-HSV-880.S10 BMS2
C
VALVE FAILURE
252-HSV-880 BMS2
OPEN LIMIT & OPEN LIMIT & NOT FAILURE

AUTO OPEN COMMAND ON 252-HSV-880.ZSO BMS2 252-HSV-880.S11 BMS2
OPEN
PROT CNCG valve 3 to CNCG RB2 burner CNCG valve 3 to CNCG RB2 burner
REL INT-28.24 CNCGB CNCG valves SEQ-28.41 CNCGB CNCG start sequence
CNCG VALVE 3 OPEN
->A TO CNCG RB2 BURNER
CLOSE
CLOSE
AUTO 252-HSV-880 OPEN LIMIT & CLOSED LIMIT & NOT FAILURE
PROT 252-HSV-880.ZSO BMS2 252-HSV-880.S12 BMS2
REL CNCG valve 3 to CNCG RB2 burner CNCG valve 3 to CNCG RB2 burner D
INT-28.24 CNCGB CNCG valves SEQ-28.42 CNCGB CNCG stop sequence
SEQ-28.41 CNCGB CNCG start sequence SEQ-28.45 CNCGB CNCG equipment in stop pos
VALVE FAILURE
252-HSV-879 BMS2
5s OPEN LIMIT & OPEN LIMIT & NOT FAILURE

AUTO 252-HSV-879.ZSO BMS2 252-HSV-879.S11 BMS2
OPEN
OFF
PROT CNCG RB2 vent valve 1 CNCG RB2 vent valve 1
REL INT-28.24 CNCGB CNCG valves SEQ-28.42 CNCGB CNCG stop sequence
CNCG RB2 VENT OPEN
->A VALVE 1
CLOSE
CLOSE
AUTO 252-HSV-879 CLOSE LIMIT & CLOSED LIMIT & NOT FAILURE E
PROT 252-HSV-879.ZSC BMS2 252-HSV-879.S12 BMS2
REL CLOSE COMMAND ON CNCG RB2 vent valve 1 CNCG RB2 vent valve 1
SEQ-28.41 CNCGB CNCG start sequence INT-28.24 CNCGB CNCG valves SEQ-28.41 CNCGB CNCG start sequence
SEQ-28.42 CNCGB CNCG stop sequence CLOSE COMMAND ON
252-HSV-879.S10 BMS2
INT-28.24 CNCGB CNCG valves PRELIMINARY
CNCGB CNCG VALVES Cust. Doc. ID:
Pos.
SEQ-28.46
Doc. ID: P00592320
0 1 2 3 4 5 6 7
A
CNCG VALVES OPEN CMD

.S3 BMS2
OK
252-PIC-846.S10 BMS2
CNCG pressure to CNCG burner B
CNCG B CNCG LANCE PRESS.
FAILURE
CONTROLLER IN AUTO MODE NC-CB3-X10017.S6
252-PIC-846B.S8 BMS2 & &
LP Steam to CNCG RB2 burner STATUS
SEQ-28.41 CNCGB CNCG start sequence & ALARM

252-PIC-846.S6 BMS2
CNCG pressure to CNCG burner DCS DI
BMS2 DO
1s 20 s
SET MONITORING ON PRESSURE FAILURE
ON
252-PIC-846B.S5 BMS2 S S .S6 BMS2 C
LP Steam to CNCG RB2 burner CNCG B CNCG BURNER FAILURE
SEQ-28.41 CNCGB CNCG start sequence R R SEQ-28.44 CNCGB CNCG burner failure
3s 2s
START-UP PROGRAM RUN
.S11
SEQ-28.41 CNCGB CNCG start sequence 1
CNCG B CNCG FAILURE
.S4 BMS2
D
FAILURE RESET
.S10 BMS2
PRELIMINARY
2 8/31/2018/TREVESSAPA 8/31/2018/FTAMJNS 8/31/2018/FTAMSRE CNCGB CNCG LANCE PRESSURE Page:
Cust. Doc. ID:
3 5/29/2020/TREJARVEJO 5/29/2020/FTAMJNS 5/29/2020/FTAMSRE MONITORING
Pos.
SEQ-28.48
Doc. ID: P00592320
0 1 2 3 4 5 6 7
CNCG B IGNITER
START
ON
PUSH-BUTTON & PUSHED LAMP TEST ON

NO 252-43-150.PB05 252-LCP-150.PB05.S1 BMS2 252-LCP-150.PB01.S1 BMS2 A
CNCG B igniter start CNCG B lamp test
SEQ-28.14 CNCGB igniter local control SEQ-28.05 CNCGB NG local controls
1
3 MeOH ADDITION CNCG B IGNITER
IGNITER FLAME ON ON
252-BX-804.S1 BMS2
CNCG B igniter
252-43-150.XL07
START-UP PROGRAM RUN PILOT LAMP
S1
CNCG B MeOH Start Sequence

S1
CNCG B MeOH Stop Sequence
SEQ-30.12 CNCGB Stop sequence MeOH B
RUNNING
.S11 BMS2
1
RUNNING
.S12 BMS2
CNCG B NG STOP SEQUENCE & PUSHED
252-LCP-150.PB06.S1 BMS2
SEQ-28.04 CNCGB NG stop sequence CNCG B igniter stop
CNCG B IGNITER CNCG B FAILURE 5s

NOT ON
STOP RESET
ON
PUSH-BUTTON PUSH-BUTTON
NC 252-43-150.PB06 NO 252-43-150.PB04 1 FAILURE RESET
.S10 BMS2
INT-28.12 CNCGB NG interlocks
CNCGB FAILURE SEQ-28.06 CNCGB NG burner failure
RESET OPR 5s SEQ-28.08 CNCGB Igniter cylinder
NC-CB3-H10026.S1
RESET DCS DO DI BMS2 SEQ-28.13 CNCGB NG leakage test
SEQ-28.15 CNCGB combustion air monitoring D
CNCG B RODDER SEQ-28.44 CNCGB CNCG burner failure
START PUSHED SEQ-28.48 CNCGB CNCG lance pressure monitoring
ON
252-LCP-150.PB17.S1 BMS2 SEQ-30.14 CNCGB Burner failure MeOH

PUSH-BUTTON CNCG B rodder start
NO 252-43-150.PB17 SEQ-30.17 CNCGB Blowing valve MeOH
SEQ-28.71 CNCGB rodder SEQ-30.18 CNCGB Atomizing air valve MeOH
PRELIMINARY
CNCGB COMMON LOCAL CONTROLS Cust. Doc. ID:
Pos.
SEQ-28.70
Doc. ID: P00592320
0 1 2 3 4 5 6 7
INTERVAL TIME SETTING

5 min (1...30 min).
A
TIME RUNNING DOWN IN DCS DISPLAY
START CNCG B RODDER

TIME SETTING
NC-CB3-H5018.I1
RESET T1 DCS AO AI BMS2
INTEGER
DCS DI
NC-CB3-H5018.S1
BMS2 DO
1s
PUSHED
252-LCP-150.PB17.S1 BMS2
CNCG B rodder start
1s
& C
1s
1 MAN
ON IN AUTO-MODE
1 AUTO
OPEN
PROT
1s REL IN COMMAND ON
CNCG RODDER OPEN
->A MOVEMENT
->M
CLOSE
ON
CLOSE
AUTO 252-HSV-828
SSO VALVES OPEN PROT
.S8 BMS2 5s REL
INT-28.26 CNCGB CNCG burner status 10 s
MeOH ADDITION
CNCGB RUNNING MEOH ON
S1 BMS 1
3 CNCG B Flame Monit MeOH
INT-30.12 CNCGB Flame monitoring MeOH
D
1s
CNCG B RUNNING NG
.S1 BMS2
CNCG B FLAME MONITORING
PRELIMINARY
CNCGB RODDER Cust. Doc. ID:
Pos.
SEQ-28.71
Doc. ID: P00592320
0 1 2 3 4 5 6 7
10 min
ON (60S)
.S2 BMS2 OFF
CNCG SUPPORT BURNING ON
INT-28.25 CNCGB support fuel status
TIME RUNNING DOWN A

IN DCS DISPLAY

252-HSV-814.S12 BMS2

252-HSV-815.S12 BMS2 &
RUNNING
.S11 BMS2 B
CNCG B IGNITION ATTEMPTS
NC-CB3-X10029.I1
CLOSED & NO FAILURE IGNITION ATTEMPTS CNCG B SUPP. FUEL START REL
252-HSV-1820S2 BMS STATUS
CNCG B methanol valve 1 GONE ON
NC-CB3-X10029.S1 NC-CB3-X10029.S2
1 STATUS STATUS
DCS AI
CLOSED & NO FAILURE
252-HSV-1821S2 BMS & INTEGER
CNCG B methanol valve 2 BMS2 AO DCS DI DCS DI
2s
START-UP PROGRAM RUN BMS2 DO BMS2 DO
S1 COUNTER
MEOH ADDITION CNCG B MeOH Start Sequence MAX 2 C
ATTEMPTS &
10 s 2s
CNCGB SPRT BURN NG START
ON NOTE: LOCAL START WITHOUT NC-CB3-X10029.S4
RESET
IGNITION ATTEMPTS LIMITATION STATUS
DCS DI
BMS2 DO
NC-CB3-H10028.S1 NG START
CNCG B &
START DCS DO DI BMS2 .S4 BMS2
NG OPERATOR CNCG B SUPRT BURN OPR STRT
CONTROL NC-CB3-H10028.S2 OPERATOR STOP D
CNCG B NG OPERATOR CONTROL
CNCGB SPRT BURN NG START
NC-CB3-X10029.S5
3
MEOH ADDITION STATUS
DCS DI
BMS2 DO
NC-CB1-H10031.S1 MEOH START

CNCG B &
START DCS DO DI BMS2 .S5 BMS2
MEOH OPERAT CNCG B SUPRT BURN OPR STRT
OR CONTROL NC-CB1-H10031.S2 OPERATOR STOP
E
CNCG B MeOH OPERATOR CONTROL
PRELIMINARY
CNCGB SUPPORT FUEL START RELEASE Cust. Doc. ID:
Pos.
SEQ-28.72
Doc. ID: P00592320
3
2
Rev.
0
Designed by
Checked by
1
Approved by
5/29/2020/TREJARVEJO 5/29/2020/FTAMJNS 5/29/2020/FTAMSRE

8/31/2018/TREVESSAPA 8/31/2018/FTAMJNS 8/31/2018/FTAMSRE
2
INT-28.27
3
LOGIC MOVED TO
Name:
Project:
Doc. ID:
4
INTERLOCKING DIAGRAMS
P00592320
CNCG burner
110374 Planta Arauco CNCG
5
OIL BURNER START CONDITIONS

Pos.
Chkcd
Drawn
Cust. Doc. ID:

6
FTAMJNS
8/3/2018/ATILJO
Appr.
Design
FTAMSRE
FTAMSLAP
7
Rev.
Page:
3
PRELIMINARY
SEQ-28.73
E
B
A
D
C

P00592320 - 3 - CNCG Burner Sequences

Uploaded by

Document Informationclick to expand document informationThis document provides a list of drawings for a project including drawing numbers, descriptions, and revision details. It also contains a disclaimer about the intellectual property and permitted use of the information.

Document Informationclick to expand document information

Copyright:

Available Formats

P00592320 - 3 - CNCG Burner Sequences

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

P00592320 - 3 - CNCG Burner Sequences

Uploaded by

Copyright:

Available Formats

Document Description Pages Rev.

SEQ-28.01 Drawing list 1 3

SEQ-28.02 Legend sheet 1 3

SEQ-28.03 CNCGB NG start sequence 5 3

SEQ-28.04 CNCGB NG stop sequence 3 3

SEQ-28.05 CNCGB NG local controls 1 3

SEQ-28.06 CNCGB NG burner failure 1 3

SEQ-28.07 CNCGB NG equipment in stop position 1 3

SEQ-28.08 CNCGB Igniter cylinder 1 3

SEQ-28.09 CNCGB Igniter 1 3

SEQ-28.11 CNCGB NG valves 1 3

SEQ-28.12 CNCGB NG leakage test sequence 5 3

SEQ-28.13 CNCGB NG leakage test 1 3

SEQ-28.14 CNCGB igniter local control 1 3

SEQ-28.15 CNCGB combustion air monitoring 1 3

SEQ-28.16 CNCGB NG lance 1 3

SEQ-28.41 CNCGB CNCG start sequence 3 3

SEQ-28.42 CNCGB CNCG stop sequence 3 3

SEQ-28.43 CNCGB CNCG local controls 1 3

SEQ-28.44 CNCGB CNCG burner failure 1 3

SEQ-28.45 CNCGB CNCG equipment in stop pos 1 3

SEQ-28.46 CNCGB CNCG valves 1 3

SEQ-28.48 CNCGB CNCG lance pressure monitoring 1 3

SEQ-28.70 CNCGB Common local controls 1 3

SEQ-28.71 CNCGB rodder 1 3

SEQ-28.72 CNCGB Support fuel start release 1 3

SEQ-28.73 Oil burner start conditions 1 3

SEQUENCE START BLOCK

->A SET SEQUENCE TO AUTO CONTROL (PULSE-WISE)

STEP JUMP PULSE

MONITORING TIME: END STEP

END STEP SHALL STOP THE SEQUENCE AND

SEQ-28.13 CNCGB NG leakage test

3s SEQ-28.07 CNCGB NG equipment in stop position CNCG B NG START SEQUENCE

OIL&MEOH BURNER NOT RUNNING CNCG B NG READY TO START

IN AUTO MODE STEP START

SEQ-28.15 CNCGB combustion air monitoring

COMBUSTION AIR DAMPER OPEN 252-HIC-817.S2

AIR DAMPER NOT CLOSED &

IN POSITION & NOT FAILURE

IGNITER FLAME & CONTROL ON

FLOW CONTROL TO IGN. POSITION 252-PIC-835.S21

CLOSE GAS VENT VALVE

CLOSED LIMIT & NOT FAILURE

MAIN FLAME DETECTING A

WAITING TIME MONITORING TIME ACTION

CNCG B MAIN FLAME ON

WAITING TIME MONITORING TIME ACTION B

CNCG B MAIN FLAME ON

OUT POSITION & NOT FAILURE

WAITING TIME MONITORING TIME ACTION

INT-28.11 CNCGB main common interlocks

OIL&MEOH BURNER NOT RUNNING CNCG B NG READY TO STOP

CLOSE GAS VALVES

CLOSED LIMIT & NOT FAILURE SEQ-28.11 CNCGB NG valves

OPEN LIMIT & NOT FAILURE

IGNITER CYLINDER OUT