Ece Nga Reviewer

MCQ in Electrical Circuit Part 1 | ECE Board Exam
pinoybix.org/2013/12/mcq-in-electrical-circuit-part-1.html
December 21, 2013
Prev Article Next Article

(Last Updated On: August 10, 2021)
This is the Multiples Choice Questions Part 1 of the Series in Electrical Circuit as one of the
Electronics Engineering topic. In Preparation for the ECE Board Exam make sure to expose
yourself and familiarize in each and every questions compiled here taken from various
sources including but not limited to past Board Exam Questions in Electronics Engineering
field, Electronics Books, Journals and other Electronics References.
MCQ Topic Outline included in ECE Board Exam Syllabi
MCQ in AC-DC circuits
1/18
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
Start with Part 1 of the Practice Exam Test Questions Series
Choose the letter of the best answer in each questions.
1. Conventional flow assumes charges flow from
A. Positive to negative
B. Positive to positive
C. Negative to positive
D. Negative to negative
View Answer:
Answer: Option A
Solution:
2. Electron flow assumes charges flow from
A. Negative to positive
B. Negative to negative
C. Positive to negative
D. Positive to positive
View Answer:
Answer: Option A
Solution:
3. Series resonance occurs when
A. XL = XC
B. XL = R
C. Z = R
D. Both A and C
View Answer:
2/18
Answer: Option D
Solution:
4. The symbol Q refers to
A. Resonance quotient
B. Quality factor
C. Power quotient
D. Qualification test
View Answer:
Answer: Option B
Solution:
5. The ratio of W/VA in an ac circuit means
A. Power factor
B. Reactive factor
C. Quality factor
D. Load factor
View Answer:
Answer: Option A
Solution:
6. What is the reciprocal of quality factor?
A. Power factor
B. Reactive factor
C. Dissipation factor
D. 1/Q factor
View Answer:
Answer: Option C
Solution:
3/18
7. In liquids and gases, ionization current results from a flow of
A. Positive or negative ions
B. Free electrons
C. Ions that are lighter in weight than electrons
D. Protons
View Answer:
Answer: Option B
Solution:
8. VL = VC in a series RLC circuit when
A. The value of the impedance is minimum
B. The power factor is zero
C. The current leads the total voltage by 90˚
D. The total voltage is zero
View Answer:
Answer: Option A
Solution:
9. At what frequency will an inductor of 5mH have the same reactance as a capacitor of 0.1
μF?
A. 7.12 kHz
B. 7.12 Hz
C. 7.12 MHz
D. 7.12 GHz
View Answer:
Answer: Option A
Solution:
10. Property of an electric circuit that dissipates electric energy
4/18
A. Reactance
B. Impedance
C. Resistance
D. Conductance
View Answer:
Answer: Option C
Solution:
11. What is the other name of relative permittivity?
A. Dielectric strength
B. Potential gradient
C. Breakdown voltage
D. Specific inductance capacity
View Answer:
Answer: Option D
Solution:
12. In a series RLC circuit
A. The current lags VL by 90˚
B. The current leads VL by 90˚
C. XL leads Xc by 90˚
D. Z = jXL at resonance
View Answer:
Answer: Option A
Solution:
13. Resistor with colored bands in the body
A. Wire-wound resistor
B. Carbon-composition resistor
5/18
C. Potentiometer
D. Rheostat
View Answer:
Answer: Option B
Solution:
14. In a resonant circuit, if Q ≥ 10 resonant frequency __________ bandwidth.
A. Bisects
B. Exceeds
C. Is less than
D. Is equal to
View Answer:
Answer: Option A
Solution:
15. Which of the following conditions is not true for a series RLC circuit at resonance?
A. Z = jXL
B. XL = XC
C. The power factor is one
D. The magnitude of Z is
View Answer:
Answer: Option A
Solution:
16. The current is ____________ times the maximum current at half-power points of a
resonance curve.
A. 0.707
B. 1.414
C. 0.5
6/18
D. 0.632
View Answer:
Answer: Option A
Solution:
17. A gang capacitor is a variable capacitor in which capacitance is varied by changing the
A. Dielectric
B. Number of plates
C. Plate area
D. Distance between plates
View Answer:
Answer: Option C
Solution:
18. In an ac circuit with inductive reactance, the
A. Phase angle of the circuit is always 45˚
B. Voltage across the inductance must be 90˚ out-of-phase with the applied voltage
C. Current through the inductance lags its induced voltage by 90˚
D. Current through the inductance and voltage across it are180˚ out-of-phase
View Answer:
Answer: Option C
Solution:
19. If three 9 mH inductors are connected in parallel without mutual inductance then the total
inductance is
A. 3 mH
B. 9 mH
C. 27 mH
D. 18 mH
7/18
View Answer:
Answer: Option A
Solution:
20. What is the specific resistance of a pure germanium?
A. 55 Ω-cm
B. 55 Ω-m
C. 55 Ω-mm
D. 55 kΩ-m
View Answer:
Answer: Option A
Solution:
21. Two capacitors of capacitance 9 μF and 18 μF in series will have a total capacitance of
A. 27 μF
B. 162 μF
C. 6 μF
D. 180 μF
View Answer:
Answer: Option C
Solution:
22. In a series RLC circuit
A. Increasing the frequency decreases the resistance
B. Increasing the frequency increases the resistance
C. Both XL and XC change as frequency changes
D. Impedance will always decrease
View Answer:
Answer: Option C
8/18
Solution:
23. A series RLC circuit has a __________ power factor at its half-power points
A. Unity
B. Leading
C. Lagging
D. Either B or C
View Answer:
Answer: Option D
Solution:
24. Kirchhoff’s laws (KCL and KVL) are applicable to
A. DC circuits
B. AC circuits
C. DC as well as AC circuits
D. Passive networks alone
View Answer:
Answer: Option C
Solution:
25. A tank circuit is a
A. Parallel LC circuit
B. Series LC circuit
C. A resonant circuit
D. A non-resonant circuit
View Answer:
Answer: Option A
Solution:
26. A capacitive load always has a ________ power facto
9/18
A. Leading
B. Lagging
C. Zero
D. Unity
View Answer:
Answer: Option A
Solution:
27. What is the temperature coefficient of the resistance Eureka?
A. Infinity
B. Negative
C. Almost zero
D. Positive
View Answer:
Answer: Option C
Solution:
28. As applied to a series RLC circuit, bandwidth means
A. The frequency range for maximum power transfer
B. The difference between the highest and lowest frequencies of the oscillator
C. The separation of the half-power points
D. The frequency at which XL = XC
View Answer:
Answer: Option C
Solution:
29. Which is considered as the effect of a dielectric material?
A. Increasing capacitance
B. Decreasing capacitance
10/18
C. Reducing the working voltage
D. Increasing the distance between the plates
View Answer:
Answer: Option A
Solution:
30. The open-circuit voltage at the terminal of load RL is 60V. Under the condition of
maximum power transfer, the load voltage will be
A. 60 V
B. 15 V
C. 20 V
D. 30 V
View Answer:
Answer: Option D
Solution:
31. If a capacitor is rated for 200V dc, what is its effective ac working voltage?
A. 50 V
B. 100 V
C. 200 V
D. 400 V
View Answer:
Answer: Option C
Solution:
32. If resonant frequency is 10 kHz and quality factor is 50, then
A. Bandwidth is 200 Hz
B. XL = is 50,000 Ω
C. R is 50 Ω
11/18
D. XC = is 50,000 Ω
View Answer:
Answer: Option A
Solution:
33. Which statement is true?
A. A series resonant circuit is of high impedance
B. A parallel resonant circuit is of low impedance
C. A series resonant circuit is inductive if it operates at a frequency higher than the resonant
frequency
D. A parallel resonant circuit is inductive if it operates at a frequency higher than the

resonant frequency
View Answer:
Answer: Option C
Solution:
34. What is considered as the most important value of a sine wave?
A. Effective value
B. Peak value
C. Average value
D. Instantaneous value
View Answer:
Answer: Option A
Solution:
35. An ac series circuit is composed of a resistance of 20 Ω, inductive reactance of 40 Ω,

and a capacitive reactance of 15 Ω. If a current of 1 ampere is flowing, what is the applied
voltage
A. 320 V
B. 32 V
C. 220 V
12/18
D. 22 V
View Answer:
Answer: Option B
Solution:
36. An intermittent and non-symmetrical alternating current like that obtained from the
secondary winding of an induction coil
A. Faradic current
B. Transient ac current
C. Inductive current
D. Capacitive current
View Answer:
Answer: Option A
Solution:
37. The value of temperature coefficient (α) is dependent upon
A. The nature of material and temperature
B. The length of material
C. The cross-sectional area of the material
D. The volume of the material
View Answer:
Answer: Option A
Solution:
38. At what frequency will the current in a series RLC circuit reach its maximum value for an
applied voltage of 15 V with R = 500 Ω, L = 100 μH and C = 0.001 μF?
A. 503 kHz
B. 403 kHz
C. 603 kHz
D. 303 kHz
13/18
View Answer:
Answer: Option A
Solution:
39. If two equal resistances connected in series across a certain supply are now connected
in parallel across the same supply, the power produced will be _________ that of series
connection
A. One-half
B. One-fourth
C. Two times
D. Four times
View Answer:
Answer: Option D
Solution:
40. The voltage lags the current by cycle in a
A. Purely resistive circuit
B. Purely inductive circuit
C. Purely capacitive circuit
D. Circuit containing resistance, capacitance and inductance
View Answer:
Answer: Option C
Solution:
41. What is the half-power bandwidth of a parallel resonant circuit which has a resonant
frequency of 3.6 MHz and Q of 218?
A. 1.65 kHz
B. 16.5 MHz
C. 16.5 kHz
D. 165 kHz
14/18
View Answer:
Answer: Option C
Solution:
42. Which one of the following elements serves as a protection against overload?
A. Fuse
B. Switch
C. Resistor
D. Relay
View Answer:
Answer: Option A
Solution:
43. Transient period is considered over after
A. 5
B. 1
C. 100
D. 6
View Answer:
Answer: Option A
Solution:
44. What rating of a resistor determines its ability to absorb heat?
A. Wattage
B. Ohmic
C. Current
D. Voltage
View Answer:
Answer: Option A
15/18
Solution:
45. An open inductor has
A. Zero resistance and infinite inductance
B. Infinite resistance and zero inductance
C. Infinite resistance and infinite inductance
D. Zero resistance and zero inductance
View Answer:
Answer: Option B
Solution:
46. What is the reading of an ohmmeter for a shorted capacitor?
A. Zero
B. Infinity
C. kΩ
D. MΩ
View Answer:
Answer: Option A
Solution:
47. What capacitance exists not through design but simply because two conducting surfaces
are relatively close to each other?
A. Surge
B. Stray
C. Natural
D. Normal
View Answer:
Answer: Option B
Solution:
16/18
48. The average value of a triangular or sawtooth wave is __________ times its peak value.
A. 0.577
B. 0.500
C. 0.318
D. 0.637
View Answer:
Answer: Option B
Solution:
49. A series RLC circuit consists of a 10 Ω resistor in series with L = 10 μH, and C = 100 μF.
Determine a new value of I, for which the resonant frequency is one –half the original value.
A. 40 μH
B. 40 mH
C. 40 pH
D. 40 nH
View Answer:
Answer: Option A
Solution:
50. What is the peak factor of a triangular wave?
A. 1.16
B. 1.73
C. 1.41
D. 1.11
View Answer:
Answer: Option B
Solution:
NEXT: MCQ in Electrical Circuit Part 2 | ECE Board Exam
17/18
Take the Interactive Practice Quiz
Practice Quiz in Electrical Circuit Part 01
Questions and Answers in Electrical Circuit
Following is the list of practice exam test questions in this brand new series:
MCQ in Electrical Circuit

PART 7: MCQ from Number 301 – 350 Answer key: included
MORE ON: MCQ in Electrical Circuit Series | ECE Board Exam
Complete List of MCQ in Electronics Engineering per topic

Series of Multiple Choice Questions in Electronics Engineering
DOWNLOAD PDF / PRINT
Please do Subscribe on YouTube!
P inoyBIX educates thousands of reviewers and students a day in preparation for their board
examinations. Also provides professionals with materials for their lectures and practice
exams. Help me go forward with the same spirit.
“Will you subscribe today via YOUTUBE?”
Subscribe
18/18
December 22, 2013

1/18
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
Continue Practice Exam Test Questions Part 2 of the Series
51. Effects of capacitance
A. It opposes any change in the amount of voltage
B. Voltage is lagged behind the current by a quarter cycle
C. Electric energy is stored in the capacitor in the form of electrostatic field
D. All of these
View Answer:
Answer: Option D
Solution:
52. Points to be considered in choosing a capacitor
A. Working voltage
B. Type of dielectric
C. Capacitance
D. All of these
View Answer:
Answer: Option D
Solution:
53. Permeability is otherwise known as
A. Magnetic conductivity
B. Magnetic susceptibility
C. Electric conductivity
D. Electric susceptibility
View Answer:
2/18
Answer: Option A
Solution:
54. The impedance in the study of electronics is represented by resistance and
A. Inductance
B. Capacitance
C. Inductance and capacitance
D. Reactance
View Answer:
Answer: Option D
Solution:
55. Loop currents should be assumed to flow in which direction
A. Straight
B. Clockwise
C. Counter-clockwise
D. Either B or C arbitrarily selected
View Answer:
Answer: Option D
Solution:
56. What determines the direction of induced emf in a conductor or coil?
A. Cork screw rule
B. Fleming’s left hand rule
C. Ampere’s circuital law
D. Fleming’s right hand rule
View Answer:
Answer: Option D
Solution:
3/18
57. The reason why electrical appliances are connected in parallel.
A. It is a simple circuit
B. This makes the operation of appliances independent with each other
C. This results in reduced power consumption
D. All of the above
View Answer:
Answer: Option B
Solution:
58. Which of the following does not affect resistance?
A. Resistivity
B. Cross-sectional area
C. Mass
D. Length
View Answer:
Answer: Option C
Solution:
59. Which of the following is not considered a physical factor affecting resistance?
A. Length
B. Material type
C. Temperature
D. Cross-sectional
View Answer:
Answer: Option C
Solution:
60. A 0.09 microfarad capacitor is charged to 220 volts. How long in milliseconds will it
discharged resistor has a resistance of 20,000 ohms?
4/18
A. 1.5
B. 2.5
C. 1.25
D. 0.5
View Answer:
Answer: Option C
Solution:
61. A trigger circuit consisting of a capacitor of 0.01 μF is connected in series with a resistor.
If the circuit requires 100 Vdc to operate, determine the value of the resistor when time
constant is 0.009s.
A. 900 Ω
B. 900 kΩ
C. 900 MΩ
D. 900 GΩ
View Answer:
Answer: Option B
Solution:
62. The graph between an alternating quantity and time is called
A. Sine wave
B. Curve
C. Waveform
D. A plot
View Answer:
Answer: Option C
Solution:
63. Which of the following is the most popular waveform?
A. Sinusoidal
5/18
B. Square wave
C. Triangular
D. Sawtooth
View Answer:
Answer: Option A
Solution:
64. Which of the following does not refer to electrical energy?
A. Volt-ampere
B. Joule
C. Watt-second
D. Volt-coulomb
View Answer:
Answer: Option A
Solution:
65. What is the resonant frequency of a circuit when L of 25 microhenrys and C of 10

picofarads are in parallel?
A. 10.1 kHz
B. 10.1 MHz
C. 101 MHz
D. 101 kHz
View Answer:
Answer: Option B
Solution:
66. And ideal current source has an internal conductance of _________ siemen(s)
A. Infinite
B. One
6/18
C. Zero
D. One million
View Answer:
Answer: Option C
Solution:
67. A capacitance of 6 µµF means
A. 6 pF
B. 6 nF
C. 6 fF
D. 6 μF
View Answer:
Answer: Option A
Solution:
68. The voltage cannot be exactly in phase with the current in a circuit that contains
A. Only capacitance
B. Only resistance
C. Inductance and capacitance
D. Inductance, capacitance and resistance
View Answer:
Answer: Option A
Solution:
69. The charge in the capacitor is stored at the
A. Terminals
B. Plates
C. Dielectric
D. Air
7/18
View Answer:
Answer: Option B
Solution:
70. The reactance curve is a plot of frequency versus ___________ for a series RLC circuit
A. Current
B. Voltage
C. Gain
D. Impedance
View Answer:
Answer: Option A
Solution:
71. For a series circuit, the higher the quality factor
A. The greater the bandwidth
B. The narrower the passband
C. The broader the resonance curve
D. The wider the passband
View Answer:
Answer: Option B
Solution:
72. “Any resistance R in a branch of a network in which a current I is flowing can be replaced
by a voltage equal to IR”. This states
A. Compensation theorem
B. Reciprocity theorem
C. Millman’s theorem
D. Superposition theorem
View Answer:
Answer: Option A
8/18
Solution:
73. The internal resistance of an ideal current source is
A. Infinite
B. Zero
C. Equal to the load resistance
D. To be determined
View Answer:
Answer: Option A
Solution:
74. If three 100-pF capacitors are connected in series, then the total capacitance is
A. 300 pF
B. 100 pF
C. 50 pF
D. 33.3 pF
View Answer:
Answer: Option D
Solution:
75. An inductance of 1 mH is
A. 0.001 H
B. 0.01 H
C. 0.0001 H
D. 0.10 H
View Answer:
Answer: Option A
Solution:
76. A capacitor is basically constructed of
9/18
A. Two conductors separated by a dielectric
B. Two dielectric separated by a conductor
C. Conductors and dielectric
D. Conductors and semiconductors
View Answer:
Answer: Option A
Solution:
77. In an inductive coil, the rate of rise of current is maximum
A. Near the final maximum value of current
B. At mid-value of current
C. At half-power points
D. After one time constant
View Answer:
Answer: Option A
Solution:
78. Two complex numbers or phasors are said to be conjugate if they
A. Differ only in the algebraic sign of their quadratic components
B. Differ only in the algebraic sign of their real components
C. Are equal in their real and quadrature components including algebraic signs
D. Are equal in their real components but differ in their quadrature components including
algebraic signs.
View Answer:
Answer: Option A
Solution:
79. In an ac circuit with a resistive branch and an inductive branch in parallel, the
A. Voltage across the inductance leads the voltage across the resistance by 90°
10/18
B. Resistive branch current is 90° out of phase with the inductive branch current
C. Resistive and inductive branch currents have the same phase
D. Resistive and inductive branch currents are 180° out-of-phase
View Answer:
Answer: Option B
Solution:
80. In an ac circuit with XL and R in series, the
A. Voltages across R and XL are in phase
B. Voltage across R lags the voltage across XL by 90°
C. Voltages across R and XL are 180° out-of-phase
D. Voltage across R leads the voltage across XL by 90°
View Answer:
Answer: Option B
Solution:
81. Leakage resistance in a capacitor results into
A. Internal heating
B. Internal bleeding
C. Shorter useful life
D. Short-circuiting
View Answer:
Answer: Option A
Solution:
82. Voltage resonance means
A. Series resonance
B. Parallel resonance
C. Current magnification
11/18
D. Gain magnification
View Answer:
Answer: Option A
Solution:
83. The unit of elastance is
A. Farad
B. Daraf
C. Siemen
D. Henry
View Answer:
Answer: Option B
Solution:
84. The farad is not equivalent to which of the following combination of units
A. CV^2
B. C^2/J
C. C/V
D. J/V^2
View Answer:
Answer: Option A
Solution:
85. Which component opposes voltage change?
A. Resistor
B. Inductor
C. Capacitor
D. Transistor
View Answer:
12/18
Answer: Option C
Solution:
86. What is the peak factor for alternating current or voltage varying sinusoidally?
A. 1.4142
B. 0.707
C. 0.636
D. 1.11
View Answer:
Answer: Option A
Solution:
87. Which of the following is not a factor affecting dielectric strength?
A. Mass
B. Moisture content
C. Temperature
D. Thickness
View Answer:
Answer: Option A
Solution:
88. The superposition theorem is used when the circuit contains
A. Reactive elements
B. Active elements
C. Number of voltage sources
D. Single voltage source
View Answer:
Answer: Option C
Solution:
13/18
89. What refers to such work at very low temperatures, near absolute zero?
A. Cryogenics
B. Superconductivity
C. Subsonic
D. Thermionic
View Answer:
Answer: Option A
Solution:
90. A factor that states how much the resistance changes for a change in temperature?
A. Resistivity
B. Specific resistance
C. Coefficient of temperature change
D. Temperature coefficient of resistance
View Answer:
Answer: Option D
Solution:
91. An alloy composed of 84 % copper, 12 % manganese and 4 % nickel.
A. Manganin
B. Constantan
C. Nichrome
D. German silver wire
View Answer:
Answer: Option A
Solution:
92. A law which states that when a constant electromotive force is applied to a circuit
consisting of a resistor and capacitor connected in series, the time taken for the potential on
the plates of the capacitor to rise to any given fraction of its final value depends only on the
14/18
product of capacitance and resistance.
A. Child’s law
B. CR law
C. Coulomb’s law
D. Debye T3 law
View Answer:
Answer: Option B
Solution:
93. At parallel resonance, the currents flowing through L and C are
A. Infinite
B. Zero
C. Unequal
D. Equal
View Answer:
Answer: Option D
Solution:
94. In a rectangular wave, the peak factor is
A. 1.16
B. 1.73
C. 1.11
D. 1.0
View Answer:
Answer: Option D
Solution:
95. In an RL series circuit,
A. Current lags voltage by less than 90˚
15/18
B. Current lags voltage by 180˚
C. Current lags voltage by 90˚
D. Current leads voltage by 90˚
View Answer:
Answer: Option A
Solution:
96. In a pure capacitance,
A. Current leads voltage by 90˚
B. Current leads voltage by 180˚
C. Current lags voltage by 90˚
D. Current lags voltage by 180˚
View Answer:
Answer: Option A
Solution:
97. The ohmic value of a resistor with negative temperature coefficient
A. Increases with increasing temperature
B. Increase with decreasing temperature
C. Stays unchanged with temperature change
D. Stays unaffected even with increasing temperature
View Answer:
Answer: Option B
Solution:
98. Which of the statements below is not true?
A. Current source is an active element
B. Resistor is a linear element
C. Voltage source is a passive element
16/18
D. Diode is a non-linear element
View Answer:
Answer: Option C
Solution:
99. Which of the following elements is active?
A. Resistor
B. Inductor
C. Capacitor
D. Ideal voltage source
View Answer:
Answer: Option D
Solution:
100. What is the complex impedance of a circuit with an absolute resistance of 300 Ω?
A. 0 + j 300 Ω
B. 300 + j 90 Ω
C. 0 – j 300 Ω
D. 300 + j 0 Ω
View Answer:
Answer: Option D
Solution:

17/18

Subscribe
18/18
December 23, 2013

1/18
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
101. The potential gradient in a cable is maximum in
A. Conductor
B. Outer sheath
C. Insulation
D. Uniformly all over
View Answer:
Answer: Option A
Solution:
102. The Q-factor of a parallel resonant circuit is also known as
A. Current magnification factor
B. Voltage magnification factor
C. Load factor
D. Leakage factor
View Answer:
Answer: Option A
Solution:
103. The Q-factor of a series resonant circuit is also known as
A. Current magnification factor
B. Voltage magnification factor
C. Load factor
D. Leakage factor
View Answer:
2/18
Answer: Option B
Solution:
104. What is the form factor of a triangular wave?
A. 1.16
B. 1.11
C. 1.73
D. 1.41
View Answer:
Answer: Option A
Solution:
105. In a rectangular wave, the form factor is
A. 1.11
B. 1.16
C. 1.0
D. 1.73
View Answer:
Answer: Option C
Solution:
106. Which of the following dielectric materials makes the highest-capacitance capacitor?
A. Air
B. Barium-strontium titanite
C. Mica
D. Electrolyte
View Answer:
Answer: Option B
Solution:
3/18
107. In a circuit, an active element is one which
A. Supplies energy
B. Receives energy
C. Both supplies and receives energy
D. Amplifies signal
View Answer:
Answer: Option A
Solution:
108. An electric circuit contains
A. Passive elements
B. Active elements
C. Both active and passive elements
D. Reactive elements
View Answer:
Answer: Option C
Solution:
109. What is the hot resistance of a 100 W, 220 V incandescent lamp?
A. 2.2 Ω
B. 22 Ω
C. 484 Ω
D. 4.84 Ω
View Answer:
Answer: Option C
Solution:
110. Which statement is true about a passive circuit?
A. A circuit with neither a source of current nor a source of potential difference
4/18
B. A circuit with a voltage source
C. A circuit with a current source
D. A circuit with only resistance as a load
View Answer:
Answer: Option A
Solution:
111. What is a closed path made of several branches of the network called?
A. Junction
B. Node
C. Terminal
D. Loop
View Answer:
Answer: Option D
Solution:
112. The internal resistance of an ideal voltage source is
A. Infinite
B. Equal to the load resistance
C. Zero
D. To be determined
View Answer:
Answer: Option C
Solution:
113. What is the conductance of a circuit having three 10 Ω resistors in parallel?
A. 0.3 S
B. 3.33 S
C. 0.33 S
5/18
D. 30 S
View Answer:
Answer: Option A
Solution:
114. Electric energy refers to
A. Volt divided by coulomb
B. Volt-ampere
C. Volt-coulomb
D. Watt divided by time
View Answer:
Answer: Option C
Solution:
115. A capacitor requires 12 μC of charge to raise its potential of 3 V. What is the

capacitance of the capacitor?
A. 36 μF
B. 15 μF
C. 0.25 μF
D. 4 μF
View Answer:
Answer: Option D
Solution:
116. A capacitor opposes change in
A. Voltage
B. Current
C. Voltage and current
D. Neither voltage nor current
6/18
View Answer:
Answer: Option A
Solution:
117. What is the total resistance of a two equal valued resistors in series?
A. The difference of both
B. The product of both
C. Twice as one
D. The sum of their reciprocals
View Answer:
Answer: Option C
Solution:
118. The ratio of maximum value to the effective value of an alternating quantity is called
A. Form factor
B. Peak factor
C. Dynamic factor
D. Leakage factor
View Answer:
Answer: Option B
Solution:
119. For series capacitors, total charge is
A. The sum of individual charges
B. Equal to the charge of either capacitors
C. Equal to the product of the charges
D. The quotient of the charges
View Answer:
Answer: Option B
7/18
Solution:
120. Series resonant circuit is sometimes known as
A. Rejector circuit
B. Acceptor circuit
C. Inductive circuit
D. Capacitive circuit
View Answer:
Answer: Option B
Solution:
121. Parallel resonant circuit is sometimes called as
A. Acceptor circuit
B. Rejector circuit
C. Inductive circuit
D. Capacitive circuit
View Answer:
Answer: Option B
Solution:
122. When two pure sine waves of the same frequency and the same amplitude which are
exactly 180˚ out-of-phase are added together, the result is
A. A wave with twice the amplitude
B. A wave with half the amplitude
C. Zero signal
D. A wave with twice the frequency
View Answer:
Answer: Option C
Solution:
8/18
123. If two complex conjugates are added, ___________ components results.
A. In-phase
B. Quadrature
C. Complex
D. Out-of-phase
View Answer:
Answer: Option A
Solution:
124. If an emf in circuit A produces a current in circuit B, then the same emf in circuit B
produces the same current in circuit A. this theorem is known as
A. Maximum power transfer theorem
B. Millman’s theorem
C. Reciprocity theorem
D. Norton’s theorem
View Answer:
Answer: Option C
Solution:
125. According to Gauss theorem, flux can be equated to
A. Charge
B. Field intensity
C. Current
D. Voltage
View Answer:
Answer: Option A
Solution:
126. An open resistor when checked with an ohmmeter reads
9/18
A. Zero
B. Infinite
C. High but within the tolerance
D. Low but not zero
View Answer:
Answer: Option B
Solution:
127. Norton’s theorem is _________ Thevenin’s theorem.
A. The same as
B. The converse of
C. Older that
D. More accurate than
View Answer:
Answer: Option B
Solution:
128. What value of R is needed with a 0.05 μF C for an RC time constant of 0.02 s?
A. 400 Ω
B. 400 MΩ
C. 400 GΩ
D. 400 kΩ
View Answer:
Answer: Option D
Solution:
129. Which of the following is the statement of Ohm’s law?
A. Electric current is directly proportional to both voltage and resistance
B. Electric current varies directly as the voltage and inversely as the resistance
10/18
C. Electrical power is directly proportional to the resistance and inversely as the current
squared
D. Electrical power is directly proportional to both voltage squared and the resistance
View Answer:
Answer: Option B
Solution:
130. The admittance of a parallel RLC circuit is found to be the _________ sum of
conductance and susceptances.
A. Algebraic
B. Arithmetic
C. Vector
D. Phasor
View Answer:
Answer: Option D
Solution:
131. A wire of one kilometer length has a resistance of 20 Ω. If the length is halved, then the
new resistance is __________ the original resistance.
A. Half
B. Twice
C. One-fourth
D. Three times
View Answer:
Answer: Option A
Solution:
132. A series-parallel combination of identical resistors will
A. Increase the power rating compared with one resistor alone
B. Increase the voltage rating compared with one resistor alone
11/18
C. Reduce the voltage rating compared with resistor alone
D. Result in an expensive circuit
View Answer:
Answer: Option A
Solution:
133. The _________ of an alternating quantity is defined as the fractional part of a period or
cycle through which the quantity has advanced from selected origin.
A. Phase
B. Frequency
C. Amplitude
D. Waveform
View Answer:
Answer: Option A
Solution:
134. An inductive circuit of resistance 16.5 Ω and inductance of 0.14 H takes a current of 25
A. if the frequency is 50 Hz, find the supply voltage.
A. 1501 V
B. 1174 V
C. 1877 V
D. 991 V
View Answer:
Answer: Option B
Solution:
135. Which of the following has a positive temperature coefficient?
A. Mica
B. Manganin
C. Silicon
12/18
D. Carbon
View Answer:
Answer: Option B
Solution:
136. The ratio of the flux density to the electric field intensity in the dielectric is called
A. Permittivity
B. Field intensity
C. Permeability
D. Elasticity
View Answer:
Answer: Option A
Solution:
137. It is impossible to change the voltage across a capacitor instantly, as this would produce
____________ current.
A. Infinite
B. Zero
C. Low
D. High
View Answer:
Answer: Option A
Solution:
138. Which of the following is not a factor affecting capacitance of a basic capacitor?
A. Area of plates
B. Number of plates
C. Distance between plates
D. Dielectric material used
13/18
View Answer:
Answer: Option B
Solution:
139. When voltage is applied across a ceramic dielectric the electrostatic field produced is 50
times greater than air dielectric. The dielectric constant of ceramic therefore is
A. 50
B. 100
C. 16.67
D. 5
View Answer:
Answer: Option A
Solution:
140. The reason why alternating current can induce voltage is
A. It has high peak value
B. It has a stronger magnetic field than direct current
C. It has a constant magnetic field
D. It has a varying magnetic field
View Answer:
Answer: Option D
Solution:
141. When two unequal values of resistors are connected in parallel across a dc source,
greater current flows through the
A. Higher resistance
B. Lower resistance
C. Higher wattage resistance
D. Lower wattage resistance
View Answer:
14/18
Answer: Option B
Solution:
142. A real current source has
A. Infinite internal resistance
B. Zero internal resistance
C. Large internal resistance
D. Small internal resistance
View Answer:
Answer: Option C
Solution:
143. What is the cross-sectional are of a conductor whose diameter is 0.001 inch?
A. One micron
B. One angstrom
C. One steradian
D. One circular mil
View Answer:
Answer: Option D
Solution:
144. Which of the following describes the action of a capacitor?
A. Stores electrical energy
B. Opposes changes in current flow
C. Creates a dc resistance
D. Converts ac to dc
View Answer:
Answer: Option A
Solution:
15/18
145. High resistance values are a consequence of the ___________ of the film.
A. Thickness
B. Length
C. Thinness
D. Area
View Answer:
Answer: Option C
Solution:
146. For parallel capacitors, total charge is
A. The sum of individual charges
B. Equal to the charge of either capacitors
C. Equal to the product of the charges
D. The quotient of the charges
View Answer:
Answer: Option A
Solution:
147. Which waveform in which the rms value and the mean value are equal?
A. Square wave
B. Triangular wave
C. Sine wave
D. Sawtooth
View Answer:
Answer: Option A
Solution:
148. In a series circuit with unequal resistances the
A. Highest R has the highest V
16/18
B. Lowest R has the highest V
C. Lowest R has the highest I
D. Highest R has the highest I
View Answer:
Answer: Option A
Solution:
149. In a parallel bank with unequal branch resistances
A. The highest R has the highest I
B. The lowest R has the highest I
C. The lowest R has the lowest V
D. The highest R has the highest V
View Answer:
Answer: Option B
Solution:
150. A rheostat is a form of
A. Variable resistor
B. Variable capacitor
C. Potentiometer
D. Thermocouple
View Answer:
Answer: Option A
Solution:
17/18


Subscribe
18/18
December 23, 2013

1/18
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
151. Metal tin becomes superconductor at approximately
A. 6K
B. 3.7K
C. 5K
D. 4.7K
View Answer:
Answer: Option B
Solution:
152. In a complex resistance-reactance plane, XL is represented
A. By an axis opposite the R axis
B. By an axis perpendicular to the XC axis
C. By an axis opposite the XC axis
D. By an axis parallel to the R axis
View Answer:
Answer: Option C
Solution:
153. When the net reactance in a series coil-capacitor circuit is zero at frequency f, the
nature of its reactance of frequency 2f is
A. Inductive
B. Capacitive
C. Resistive
D. Infinite
2/18
View Answer:
Answer: Option A
Solution:
154. Which of the following is a way of decreasing mutual inductance?
A. Moving the coils closer
B. Moving the coils apart
C. Decreasing the number of turns of either coil
D. Increasing the number of turns of either coil
View Answer:
Answer: Option B
Solution:
155. The charging of a capacitor through a resistance obeys
A. Exponential law
B. Logarithmic law
C. Linear law
D. Square law
View Answer:
Answer: Option A
Solution:
156. The Q-factor of a parallel resonant circuit is also known as
A. Voltage magnification factor
B. Current magnification factor
C. Gain magnification factor
D. Resonance magnification factor
View Answer:
Answer: Option B
3/18
Solution:
157. What is the specific resistance of a pure silicon?
A. 55 Ω-mm
B. 55 Ω-m
C. 55 Ω-cm
D. 55 kΩ-m
View Answer:
Answer: Option C
Solution:
158. A capacitance of 0.05 μF equals
A. 0.05 x 10^6 F
B. 0.05 x 10^-6 F
C. 0.05 x 10^-12 F
D. 0.05 x 10^12 F
View Answer:
Answer: Option B
Solution:
159. A 5 μF capacitor charge to 5V has a stored charge equal to
A. 1 μc
B. 5 μc
C. 25 μC
D. 200 μc
View Answer:
Answer: Option C
Solution:
160. The factor 0.707 for converting peak to rms applies only to
4/18
A. Square waves
B. Triangle waves
C. Sawtooth waves
D. Sine waves
View Answer:
Answer: Option D
Solution:
161. When two in-phase sine waves that have identical frequency and amplitude are added
together, then the result is a sine wave with __________ the amplitude of either.
A. Half
B. Twice
C. Four times
D. One-fourth
View Answer:
Answer: Option B
Solution:
162. Liquids that are good conductors because of ionization are called
A. Electrolytic
B. Bases
C. Acid
D. Electrolytes
View Answer:
Answer: Option D
Solution:
163. Tungsten filament of bulbs has a hot resistance higher than its cold resistance due to its
temperature coefficient which is
A. Positive
5/18
B. Negative
C. Zero
D. Infinite
View Answer:
Answer: Option A
Solution:
164. A term used to express the amount of electrical energy stored in electrostatic field.
A. Joules
B. Coulombs
C. Watts
D. Electron-volt
View Answer:
Answer: Option A
Solution:
165. With double the number of turns by the same length and area, the inductance is
A. The same
B. Doubled
C. Quartered
D. Quadrupled
View Answer:
Answer: Option D
Solution:
166. The temperature coefficient of resistance of electrolytes is
A. Negative
B. Positive
C. Zero
6/18
D. Infinite
View Answer:
Answer: Option A
Solution:
167. What refers to the lowest voltage across any insulator that can cause current flow?
A. Conduction voltage
B. Critical voltage
C. Breakdown voltage
D. Voltage capacity
View Answer:
Answer: Option C
Solution:
168. Capacitance increase with
A. Larger plate area and less distance between plates
B. Larger plate area and greater distance between plates
C. Smaller plate area and less distance between plates
D. Higher values of applied voltage
View Answer:
Answer: Option A
Solution:
169. What is the resonant frequency of a circuit when L of 3 microhenrys and C of 40

picofarads are in series?
A. 14.5 kHz
B. 145 MHz
C. 14.5 MHz
D. 145 kHz
7/18
View Answer:
Answer: Option C
Solution:
170. For a triangular and sawtooth waveform the rms voltage or current equals
A. 0.707 times peak value
B. 0.577 times peak value
C. 0.577 times average value
D. 0.707 times rms value
View Answer:
Answer: Option B
Solution:
171. If two resistances of 9 Ω and 6 Ω are connected in parallel, the total resistance is
A. 54 Ω
B. 0.3 Ω
C. 15 Ω
D. 3.6 Ω
View Answer:
Answer: Option D
Solution:
172. Refers specifically to steady state values of quantities in ac circuits which are complex
numbers.
A. Domain
B. Scalar quantity
C. Vector quantity
D. Phasor quantity
View Answer:
Answer: Option D
8/18
Solution:
173. A capacitor is used to
A. Block dc current
B. Pass dc current
C. Open voltage source
D. Short the voltage source
View Answer:
Answer: Option A
Solution:
174. The usual load of a dc circuit is a/an
A. Resistor
B. Capacitor
C. Inductor
D. Both inductor and capacitor
View Answer:
Answer: Option A
Solution:
175. The second strip of an electronic resistor color-code represents
A. The multiplier
B. The second digit of the value
C. The temperature
D. The tolerance
View Answer:
Answer: Option B
Solution:
176. Which of the following is a preferred resistor value?
9/18
A. 520
B. 47
C. 43,000
D. 54,321
View Answer:
Answer: Option B
Solution:
177. A three-by-three, series-parallel matrix of resistors, all having the same ohmic value,
would have a net resistance of
A. One-third the value of a single resistor
B. Three times the value of a single resistor
C. The same value as a single resistor
D. Nine times the value of a single resistor
View Answer:
Answer: Option C
Solution:
178. In an ac wave, 30 degrees of phase is _________ of a cycle.
A. ½
B. 1/12
C. 1/3
D. 1/30
View Answer:
Answer: Option B
Solution:
179. What is the value of a carbon composition resistor with the following color code: Brown,
white, orange, red
A. 190 Ω; 10%
10/18
B. 19 kΩ; 2%
C. 19 kΩ; 20%
D. 1.9 kΩ; 2%
View Answer:
Answer: Option B
Solution:
180. The electric field strength between capacitor plates has a unit of
A. Volts per meter
B. Volts per mil
C. Amperes per meter
D. Amperes per mil
View Answer:
Answer: Option A
Solution:
181. For multi-plate capacitor, capacitance is proportional to
A. Number of plates less one (n – 1)
B. Number of plates plus one (n + 1)
C. Number of plates less two (n – 2)
D. Number of plates (n)
View Answer:
Answer: Option A
Solution:
182. A capacitor consists of two
A. Conductors only
B. Dielectric only
C. Conductors separated by a dielectric
11/18
D. Dielectric separated by a conductor
View Answer:
Answer: Option C
Solution:
183. How many coulombs are delivered by a storage battery in 25 hours if it is supplying
current at the rate of 3 A?
A. 2.592 x 10^5 C
B. 2.592 x 10^3 C
C. 2.592 x 10^8 C
D. 2.592 x 10^12 C
View Answer:
Answer: Option A
Solution:
184. When frequency of an ac wave decreases, the value of XL in a coil
A. Approaches zero
B. Gets larger positively
C. Gets larger negatively
D. Stays constant
View Answer:
Answer: Option A
Solution:
185. The temperature-resistance coefficient of pure gold is
A. 0.0034
B. 0.0037
C. 0.0038
D. 0.0039
12/18
View Answer:
Answer: Option A
Solution:
186. The capacitor opposes any change in voltage across it by
A. Passing a voltage proportional to the rate of change of current
B. Acting as a short circuit at time equal to zero
C. Passing a current proportional to the rate of change of voltage
D. Acting as a short circuit at time equal to infinity
View Answer:
Answer: Option C
Solution:
187. What is the most common non-sinusoidal waveform?
A. Square wave
B. Triangular wave
C. Trapezoidal wave
D. Sawtooth wave
View Answer:
Answer: Option A
Solution:
188. Which of the following capacitors is suitable for dc filter circuits?
A. Mica
B. Ceramic
C. Paper
D. Electrolytic
View Answer:
Answer: Option D
13/18
Solution:
189. A series RL circuit has R of 10 Ω and XL of 5 Ω, its impedance in rectangular form is

given by
A. 10 + j5 Ω
B. 10 + j10 Ω
C. 10 – j5 Ω
D. 10 – j10 Ω
View Answer:
Answer: Option A
Solution:
190. What is the reciprocal of capacitance?
A. Reluctance
B. Susceptance
C. Elastance
D. Conductance
View Answer:
Answer: Option C
Solution:
191. If the output resistance of a voltage source is 4 Ω, it internal resistance should be
A. 4 Ω
B. 8 Ω
C. 2 Ω
D. Infinite
View Answer:
Answer: Option A
Solution:
14/18
192. The curve between current and frequency is termed as
A. Voltage curve
B. Gain curve
C. Power curve
D. Resonance curve
View Answer:
Answer: Option D
Solution:
193. What is the total effective capacitance of two 0.25 μF capacitors connected in series?
A. 0.125 μF
B. 1.25 μF
C. 0.50 μF
D. 2.5 if
View Answer:
Answer: Option A
Solution:
194. What can be used to estimate resonant frequency and to find reactance at any
frequency for any value of capacitor or inductor?
A. Smith chart
B. Reactance chart
C. Impedance chart
D. Resonance chart
View Answer:
Answer: Option B
Solution:
195. For a parallel AC circuit, ___________ is used as a reference phasor.
15/18
A. Voltage
B. Power
C. Current
D. Resistance
View Answer:
Answer: Option A
Solution:
196. For a series AC circuit, _________ is not used as a reference phasor.
A. Voltage
B. Impedance
C. Current
D. Conductance
View Answer:
Answer: Option A
Solution:
197. If a certain circuit has a current that is lagging the voltage by 45˚, then it displays
A. Pure inductive reactance
B. Resistance and capacitance reactance
C. Resistance and inductive reactance
D. Pure capacitive reactance
View Answer:
Answer: Option C
Solution:
198. What maximum voltage can be applied across the capacitor for very short period of
time?
A. Working voltage
16/18
B. Surge voltage
C. Stray voltage
D. Peak voltage
View Answer:
Answer: Option B
Solution:
199. What is expected when two 20 kΩ, 1 watt resistor in parallel are use instead of one 10
kΩ, 1 watt?
A. Provides higher current
B. Provides less power
C. Provides more power
D. Provides wider tolerance
View Answer:
Answer: Option C
Solution:
200. Which of the following materials has the lowest dielectric strength?
A. Glass
B. Paper
C. Mica
D. Teflon
View Answer:
Answer: Option B
Solution:
17/18


Subscribe
18/18
December 23, 2013

1/18
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
201. The distance between the capacitor plates increases two times, then its capacitance
A. Increases two times
B. Increases four times
C. Decreases two times
D. Decreases four times
View Answer:
Answer: Option C
Solution:
202. The ratio between the active power and the apparent power of a load in an ac circuit is
called
A. Quality factor
B. Power factor
C. Power ratio
D. Power reactive
View Answer:
Answer: Option B
Solution:
203. When the power factor of a circuit is zero,
A. Power absorbed is maximum
B. Power absorbed is minimum
C. Power absorbed is zero
D. The impedance is minimum
2/18
View Answer:
Answer: Option C
Solution:
204. How many degrees of phase represents one full cycle?
A. 360
B. 180
C. 270
D. 90
View Answer:
Answer: Option C
Solution:
205. Which of the following does not generally affect the value of a capacitor?
A. The dielectric material used
B. The surface area of the plates
C. The thickness of the dielectric
D. The voltage applied to the plate
View Answer:
Answer: Option D
Solution:
206. What is the purpose of a load in an electric circuit?
A. To increase the circuit current
B. To decrease the circuit current
C. To utilize electrical energy
D. To make the circuit complete
View Answer:
Answer: Option C
3/18
Solution:
207. The power factor of a certain circuit in which the voltage lags behind the current is 80%.
To increase the power to 100%, it is necessary to add ________ to the circuit.
A. Inductance
B. Capacitance
C. Resistance
D. Impedance
View Answer:
Answer: Option A
Solution:
208. Refers to the outward-curving distortion of the lines of force near the edges of two
parallel metal plates that form a capacitor.
A. Skin effect
B. Night effect
C. Edge effect
D. Hall effect
View Answer:
Answer: Option C
Solution:
209. If voltage across the plates of 2 F capacitor is increased by 4 V, then charge on the
plates will
A. Decrease by 2 C
B. Increase by 2 C
C. Decrease by 4 C
D. Increase by 4 C
View Answer:
Answer: Option D
4/18
Solution:
210. What does a capacitor store?
A. Voltage
B. Charge
C. Current
D. Power
View Answer:
Answer: Option B
Solution:
211. The mutual inductance between two coils is ___________ the reluctance of magnetic
path.
A. Directly proportional to
B. Inversely proportional to
C. Independent to
D. Equal to
View Answer:
Answer: Option B
Solution:
212. The result of rust in electrical (wire) connection is
A. Inductance
B. Conductance
C. Impedance
D. Resistance
View Answer:
Answer: Option D
Solution:
5/18
213. Which of the following is a disadvantage of a wire-wound resistor?
A. It has reactance in radio-frequency circuits
B. It cannot handle much power
C. It draws a large amount of current
D. It cannot handle high voltage
View Answer:
Answer: Option A
Solution:
214. The resistance of an insulator __________ when its temperature is increased.
A. Decreases
B. Remains the same
C. Increases
D. Varies
View Answer:
Answer: Option A
Solution:
215. The wavelength of an alternating waveform depends upon the ___________ of the
variation.
A. Period
B. Number
C. Frequency
D. Amplitude
View Answer:
Answer: Option C
Solution:
216. Delta to wye or wye to delta transformation technique is applied to a _________

network.
6/18
A. One-terminal
B. Two-terminal
C. Three-terminal
D. Complex
View Answer:
Answer: Option C
Solution:
217. For greater accuracy, the value of phase angle θ should be determined from
A. Cos θ
B. Tan θ
C. Sin θ
D. Sec θ
View Answer:
Answer: Option B
Solution:
218. Inductive reactance applies only to sine waves because it
A. Increases with lower frequencies
B. Increases with lower inductance
C. Depends on the factor 2 π
D. Decreases with higher frequencies
View Answer:
Answer: Option C
Solution:
219. What increases the resistance of wire at high frequencies?
A. Temperature
B. Voltage
7/18
C. Skin effect
D. Insulation
View Answer:
Answer: Option C
Solution:
220. An inductor carries 2 A dc. If its inductance is 100 μH, then what is its inductive
reactance?
A. Zero
B. 1.3 kΩ
C. 628 Ω
D. -628 Ω
View Answer:
Answer: Option A
Solution:
221. Barium-strontium titanite dielectric material is also called
A. Ceramic
B. Polyster
C. Electrolytic
D. Bakelite
View Answer:
Answer: Option A
Solution:
222. In the 5-band method of capacitor color coding, the first band indicates
A. Temperature coefficient
B. Tolerance
C. 1st digit
8/18
D. Capacitance value
View Answer:
Answer: Option A
Solution:
223. What is the most convenient way of achieving large capacitance?
A. By using multiplate construction
B. By using air as dielectric
C. By decreasing distance between plates
D. By using dielectric of low permittivity
View Answer:
Answer: Option A
Solution:
224. A linear circuit is one whose parameters
A. Change with change in voltage
B. Change with change in current
C. Do not change with voltage and current
D. Change with change in voltage and current
View Answer:
Answer: Option C
Solution:
225. For a linear circuit, __________ voltage or current is used to calculate average power.
A. Rms
B. Peak
C. Average
D. Instantaneous
View Answer:
9/18
Answer: Option A
Solution:
226. When two coils of identical reactance are in parallel without mutual inductance, the
reactance of the combination is _________ the reactance of each coil.
A. One half
B. Twice
C. Four times
D. One fourth
View Answer:
Answer: Option A
Solution:
227. Which of the following is also known as anti-resonant circuit?
A. Parallel resonant circuit
B. Series resonant circuit
C. Tuned circuit
D. Tank circuit
View Answer:
Answer: Option A
Solution:
228. In a complex number 5 + j 10, 10 is called _________ part.
A. Imaginary
B. Real
C. Conjugate
D. Integer
View Answer:
Answer: Option A
10/18
Solution:
229. The presence of an electric current is made known by
A. Electric shock
B. Effects produced
C. Magnetic shock
D. Flashing
View Answer:
Answer: Option B
Solution:
230. The reciprocal of a complex number is
A. A complex number
B. A real number
C. An imaginary number
D. A whole number
View Answer:
Answer: Option A
Solution:
231. Which of the following has negative temperature coefficient?
A. Carbon
B. Nickel
C. Brass
D. Constantan
View Answer:
Answer: Option A
Solution:
232. Which of the following is a common material used in wire-wound resistors?
11/18
A. Manganin
B. Carbon
C. Bronze
D. German silver wire
View Answer:
Answer: Option A
Solution:
233. If one resistance in a series connection is open, then
A. The current is zero in all the other resistances
B. The current is maximum in all the other resistances
C. The voltage is zero across the open resistance
D. The voltage is infinite across the open resistance
View Answer:
Answer: Option A
Solution:
234. What determines the magnitude of electric current?
A. The rate at which electrons are produced
B. The type of material used
C. The current carrying capacity of the circuit
D. The rate at which electrons pass a given point
View Answer:
Answer: Option D
Solution:
235. For a carbon composition resistor, typical resistance values range from
A. 2.7 Ω to 22 MΩ
B. 1000 Ω to 10000 Ω
12/18
C. 10 Ω to 10 MΩ
D. 2.7 Ω to 2.7 GΩ
View Answer:
Answer: Option A
Solution:
236. A lead conductor has a resistance of 25Ω at 0˚C. Determine its resistance at -30˚C.
A. 22Ω
B. 24Ω
C. 12Ω
D. 11Ω
View Answer:
Answer: Option A
Solution:
237. An impedance given by 90∠-45˚ is a/an __________ impedance.
A. Inductive
B. Conductive
C. Resistive
D. Capacitive
View Answer:
Answer: Option D
Solution:
238. If a coil has a Q of 10, it means that
A. The energy stored in the magnetic field of the coil is 10 times the energy wasted in its
resistance
B. The energy wasted in its resistance is 10 times the energy stored in the magnetic field of
the coil
C. It is a low Q coil
13/18
D. It is a high Q coil
View Answer:
Answer: Option A
Solution:
239. What is the rms value of a square wave?
A. Equals its peak value
B. Equals its peak-to-peak value
C. Peak divided by square root of two
D. Peak divided by pi
View Answer:
Answer: Option A
Solution:
240. The rms value of a triangular or sawtooth waveform is ___________ times its peak
value.
A. 0.577
B. 0.500
C. 0.25
D. 0.707
View Answer:
Answer: Option A
Solution:
241. In a multiple capacitor, the plate area is
A. Increased
B. The same
C. Decreased
D. Variable
14/18
View Answer:
Answer: Option A
Solution:
242. What is the time constant for L of 240 mH in series with R of 20Ω?
A. 12 ms
B. 4.8 s
C. 83.3 s
D. 12 s
View Answer:
Answer: Option A
Solution:
243. In an ac circuit, the power dissipated as heat depends on
A. Impedance
B. Capacitive reactance
C. Resistance
D. Inductive reactance
View Answer:
Answer: Option C
Solution:
244. Which of the following dielectric materials makes the lowest-capacitance capacitor?
A. Paper
B. Mica
C. Air
D. Electrolyte
View Answer:
Answer: Option C
15/18
Solution:
245. In adding or subtracting phasor quantities, ____________ form is the most convenient.
A. Polar
B. Rectangular
C. Trigonometric
D. Exponential
View Answer:
Answer: Option B
Solution:
246. In dividing or multiplying phasor quantities, ____________ form is used.
A. Polar
B. Rectangular
C. Trigonometric
D. Exponential
View Answer:
Answer: Option A
Solution:
247. The power factor of a circuit is equal to
A. RZ
B. XC/Z
C. XL/Z
D. R/Z
View Answer:
Answer: Option D
Solution:
248. The capacitance of a capacitor is ____________ relative permittivity.
16/18
A. Directly proportional to
B. Inversely proportional to
C. Equal to
D. Inversely proportional to the square of
View Answer:
Answer: Option A
Solution:
249. If a multi-plate capacitor has 10 plates, each of area 10 cm^2, then
A. 10 capacitors will be in parallel
B. 10 capacitors will be in series
C. 9 capacitors will be in parallel
D. 9 capacitors will be in series
View Answer:
Answer: Option C
Solution:
250. Of the equivalent combination of units, which one is not equal to watt?
A. Ω^2/V
B. AV
C. A^2 Ω
D. J/s
View Answer:
Answer: Option A
Solution:
17/18


Subscribe
18/18
December 24, 2013

(Last Updated On: November 24, 2020)
1/17
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
251. A neon glow lamp used as a night light ionizes at approximately.
A. 70 V
B. 80 V
C. 90 V
D. 100 V
View Answer:
Answer: Option A
Solution:
252. What dielectric is generally employed by a variable capacitor?
A. Mica
B. Air
C. Electrolyte
D. Ceramic
View Answer:
Answer: Option B
Solution:
253. A switch designed to have low capacitance between its terminal when open.
A. LOCAP switch
B. AntiLOCAP switch
C. Anticapacitance switch
D. Capacitance switch
View Answer:
2/17
Answer: Option C
Solution:
254. A resistor wound with a wire doubled back on itself to reduce the inductance.
A. Bifilar resistor
B. Wire-wound resistor
C. Anti-inductive resistor
D. Bleeder resistor
View Answer:
Answer: Option A
Solution:
255. What fusion of elements is without chemical action between them?

A. Mixture
B. Compound
C. Alloy
D. Ionization
View Answer:
Answer: Option C
Solution:
256. In calculating maximum instantaneous power ___________ voltage or current is used.

A. Peak
B. Average
C. Rms
D. Instantaneous
View Answer:
Answer: Option A
Solution:
257. The area of capacitor plates increases two times, then its capacitance
A. Increases two times
3/17
B. Increases four times
C. Decreases two times
D. Decreases four times
View Answer:
Answer: Option A
Solution:
258. If the inductance is decreased, the impedance of the circuit containing a resistor a
capacitor and an inductor connected in series to an ac source
A. Decreases
B. Increases
C. Decreases or increases
D. Decreases, increases or remains the same
View Answer:
Answer: Option C
Solution:
259. When the movable plates of a gang capacitor completely overlap the fixed plates, the
capacitance of the capacitor is
A. Halfway between maximum and minimum
B. Maximum
C. Minimum
D. Zero
View Answer:
Answer: Option B
Solution:
260. In a circuit, a passive element is one which
A. Supplies energy
B. Receives energy
C. Both supplies and receives energy
4/17
D. Attenuates signal
View Answer:
Answer: Option B
Solution:
261. Rationalizing the denominator of a complex number means
A. Eliminating the j component in the denominator
B. Adding j component in the denominator
C. Eliminating the j component in the numerator
D. Adding j component in the numerator
View Answer:
Answer: Option A
Solution:
262. When two complex conjugates are subtracted, the result is a
A. Quadrature component only
B. Complex component
C. In-phase component
D. Real component
View Answer:
Answer: Option A
Solution:
263. A coil of inductance L has an inductive reactance of XL in an ac circuit in which the

effective current is I. The coil is made from a superconducting material. The rate at which
power is dissipated in the coil is
A. 0
B. I^2XL
C. IXL
D. IXL2
5/17
View Answer:
Answer: Option A
Solution:
264. If the capacitance of mica capacitor is 5 times the capacitance of air capacitor, then the
relative permittivity of mica is
A. 2.5
B. 5
C. 10
D. 25
View Answer:
Answer: Option B
Solution:
265. The hot resistance of an incandescent lamp is about ____________ times its cold
resistance.
A. 10
B. 5
C. 50
D. 100
View Answer:
Answer: Option A
Solution:
266. When the temperature of copper wire is increased its resistance is

A. Increased
B. Decreased
C. Constant
D. Zero
View Answer:
Answer: Option A
Solution:
6/17
267. A trimmer is a variable capacitor in which capacitance is varied by changing the
A. Number of plates
B. Dielectric
C. Distance between plates
D. Plate area
View Answer:
Answer: Option C
Solution:
268. The reason why electrical appliances are not connected in series.
A. Greater electrical power saving
B. Power loss is minimum
C. Appliances have different current ratings
D. All of the above
View Answer:
Answer: Option C
Solution:
269. Form its definition, the unit of electric field, is the N/C and equivalent unit of is the
A. V(m)^2
B. V(m)
C. V/m^2
D. V/m
View Answer:
Answer: Option D
Solution:
270. Which of the following is the peakiest?
A. Square wave
B. Sinusoidal wave
7/17
C. Triangular wave
D. Rectangular wave
View Answer:
Answer: Option C
Solution:
271. Why are inductance and capacitance not relevant in a dc circuit?

A. Because it is a simple circuit
B. Because dc circuits require only resistance as load
C. Because they do not exist in a dc circuit
D. Because frequency of dc is zero
View Answer:
Answer: Option D
Solution:
272. When capacitors are connected in parallel, the total capacitance is

A. Greater than the largest capacitor
B. Smaller than the largest capacitor
C. Smaller than the smallest capacitor
D. Greater than the smallest capacitor
View Answer:
Answer: Option A
Solution:
273. When current and voltage are in phase in an ac circuit, the _____________ is equal to
zero.
A. Resistance
B. Reactance
C. Inductance
D. Capacitance
View Answer:
8/17
Answer: Option B
Solution:
274. Thevenin’s theorem is what form of an equivalent circuit?

A. Current
B. Voltage
C. Both current and voltage
D. Neither current nor voltage
View Answer:
Answer: Option B
Solution:
275. Which of the following combination of length and cross-sectional area will give a certain
volume of copper the least resistance?
A. 2L and 1/2 A
B. Does not matter because the volume of copper remains the same
C. L and A
D. ½ L and 2 A
View Answer:
Answer: Option D
Solution:
276. The ratio between the reactive power and the apparent power of an ac load is called
A. Quality factor
B. Power factor
C. Power ratio
D. Reactive power
View Answer:
Answer: Option D
Solution:
277. What is the efficiency under the conditions of maximum power transfer?
9/17
A. 50 %
B. 100 %
C. 25 %
D. 75 %
View Answer:
Answer: Option A
Solution:
278. The charging of a capacitor through a resistance follows what law?

A. Linear law
B. Hyperbolic law
C. Inverse-square law
D. Exponential law
View Answer:
Answer: Option D
Solution:
279. Norton’s theorem is what form of an ac equivalent circuit?
A. Voltage
B. Current
C. Both voltage and current
D. Neither voltage nor current
View Answer:
Answer: Option B
Solution:
280. What is the total capacitance of 10 capacitors, each of 20 μF in series?

A. 200 μF
B. 2 μF
C. 100 μF
10/17
D. 0.5 μF
View Answer:
Answer: Option B
Solution:
281. An inductive load always has a ___________ power factor
A. Leading
B. Lagging
C. Zero
D. Unity
View Answer:
Answer: Option B
Solution:
282. When resistance are connected in parallel, the total resistance is

A. Less than the smallest resistance in the connection
B. Greater than the smallest resistance in the connection
C. Between the smallest and greatest resistance in the connection
D. Increasing and decreasing depending upon the supply voltage
View Answer:
Answer: Option A
Solution:
283. The arc across a switch when it open an RL circuit is a result of the
A. Large self-induced voltage across L
B. Long time constant
C. Low resistance of the open switch
D. Surge of resistance
View Answer:
Answer: Option A
11/17
Solution:
284. What is a rotating vector whose projection can represent either current or voltage in an
ac circuit?
A. Polar diagram
B. Scalar quantity
C. Velocity
D. Phasor
View Answer:
Answer: Option D
Solution:
285. Which factor does not affect resistance?
A. Length
B. Resistivity
C. Cross-sectional area
D. Mass
View Answer:
Answer: Option D
Solution:
286. Which of the following capacitors are used only in dc circuits?
A. Mica
B. Ceramic
C. Mylar
D. Electrolytic
View Answer:
Answer: Option D
Solution:
287. The maximum power transfer theorem is used in
12/17
A. Power system
B. Electronic system
C. Refrigeration
D. Air conditioning
View Answer:
Answer: Option B
Solution:
288. In Norton’s theorem, the short circuit current is obtained by
A. Opening the load terminals
B. Shorting the load terminals
C. Opening the voltage source
D. Shorting the voltage source
View Answer:
Answer: Option B
Solution:
289. For maximum power transfer, what is the relation between load resistance RL and
internal resistance R of the voltage source?
A. RL = 2 r
B. RL = 1.5 r
C. RL = r
D. RL = 3 r
View Answer:
Answer: Option C
Solution:
290. A capacitor of 0.5 μF charged to 220 V is connected across an uncharged 0.5 μF

capacitor. What is the voltage across each capacitor?
A. 220 V
B. 150 V
13/17
C. 110 V
D. 22 V
View Answer:
Answer: Option C
Solution:
291. When capacitors are connected in series, the total capacitance is

A. Smaller than the smallest capacitor
B. Smaller than the largest capacitor
C. Greater than any of the capacitor
D. Greater than the largest capacitor
View Answer:
Answer: Option A
Solution:
292. What theorem is generally used in the analysis of vacuum tubes?

A. Superposition theorem
C. Thevenin’s theorem
View Answer:
Answer: Option C
Solution:
293. Another term of the quality factor of the resonant circuit.

A. Figure of merit
B. Figure of demerit
C. Noise factor
D. Noise figure
View Answer:
Answer: Option A
14/17
Solution:
294. Which of the following represents the energy stored in a capacitor?

A. CV^2/2
B. 2Q^2/C
C. C^2/V
D. CV
View Answer:
Answer: Option A
Solution:
295. What theorem is usually used in the analysis of transistor circuit?

A. Superposition theorem
C. Thevenin’s theorem
View Answer:
Answer: Option D
Solution:
296. Which of the following capacitors has the highest cost per μF?
A. Plastic
B. Air
C. Mica
D. Electrolytic
View Answer:
Answer: Option D
Solution:
297. Under the conditions of maximum power transfer, a voltage source is delivering a power
of 15 W to the load. What is the power generated by the source?
A. 60 W
15/17
B. 30 W
C. 15 W
D. 4 W
View Answer:
Answer: Option B
Solution:
298. Which of the following is neither a basic physical law nor deliverable from one?
A. Ohm’s law
B. Coulomb’s law
C. Kirchhoff’s first law
D. Kirchhoff’s second law
View Answer:
Answer: Option A
Solution:
299. Another term for superconductor.
A. Generic conductor
B. Ultraconductor
C. Cryotron
D. Cryogenic conductor
View Answer:
Answer: Option D
Solution:
300. A circuit whose parameters change with voltage or current.
A. Non-linear circuit
B. Linear circuit
C. Complex circuit
16/17
D. Passive circuit
View Answer:
Answer: Option A
Solution:


17/17
April 15, 2018

1/18
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
301. The total resistance of a two similar wire conductors connected in parallel is ________.
A. resistance of one wire multiplied by 4
B. same resistance of one wire
C. one half the resistance of one wire
D. double the resistance of one wire
View Answer:
Answer: Option C
Solution:
302. What is the value of a resistor with colors from left: Orange, Blue, Gold, and Silver?
A. 34 ohms ± 10%
B. 3.6 ohms ± 10%
C. 3.4 ohms ± 10%
D. 36 ohms ± 10%
View Answer:
Answer: Option B
Solution:
303. Determine the value of a resistor with colors from left to right; Brown, Green, Gold, and
Silver.
A. 1.5 ohms ± 10%
B. 15 ohms ± 10%
C. 1.5 ohms ± 20%
D. 15 ohms ± 20%
2/18
View Answer:
Answer: Option A
Solution:
304. Resistors with high value usually have lower wattage ratings because of _________.
A. varying current
B. lower current
C. bigger size
D. high current
View Answer:
Answer: Option B
Solution:
305. Smaller resistors usually have ________ resistance value.
A. small
B. high
C. low
D. very small
View Answer:
Answer: Option B
Solution:
306. When resistors are connected in series, what happens?
A. The effective resistance is decreased
B. Nothing
C. The tolerance is decreased
D. The effective resistance is increased
View Answer:
Answer: Option D
3/18
Solution:
307. A 33 kilo ohms resistor is connected in series with a parallel combination made up of a
56 kilo ohm resistor and a 7.8 kilo ohm resistor. What is the total combined resistance of
these three resistors?
A. 63769 ohms
B. 49069 ohms
C. 95800 ohms
D. 39067 ohms
View Answer:
Answer: Option D
Solution:
308. If you need a 1.25 kΩ resistance and you only have resistors of 5 kΩ, how many of
these available resistors you should connect in parallel to get a 1.25 kΩ value?
A. 2
B. 3
C. 4
D. 5
View Answer:
Answer: Option C
Solution:
309. Insulating elements or materials has a capability of
A. allowing electric current to flow
B. supporting charge flow
C. preventing short circuit between conducting wires
D. making electrical circuits to be completed
View Answer:
Answer: Option C
4/18
Solution:
310. _________ is used to store electrical energy in an electrostatic field?
A. A transformer
B. A battery
C. A capacitor
D. An inductor
View Answer:
Answer: Option C
Solution:
311. What factors determine the capacitance of a capacitor?
A. Area of the plates, amount of charge on the plates and the dielectric constant of the
material between the plates
B. Area of the plates, voltage on the plates and the distance between the plates
C. Area of the plates, distance between the plates, and the dielectric constant of the material
between the plates
D. Area of the plates, voltage on the plates and dielectric constant of the material between
the plates
View Answer:
Answer: Option C
Solution:
312. Factors that determine the capacitance of a capacitor.
A. area of the plate; directly proportional
B. distance between plate; inversely proportional
C. dielectric constant; directly proportional
D. all of these
View Answer:
Answer: Option D
5/18
Solution:
313. An electronic/electrical component/device used to store electrical energy.
A. Capacitor
B. Inductor
C. Resistor
D. lightning arrester
View Answer:
Answer: Option A
Solution:
314. Which of the following describes the action of a capacitor?
A. Converts ac into dc
B. Stores electrical energy
C. Opposes change in current flow
D. Creates a dc resistance
View Answer:
Answer: Option B
Solution:
315. A parallel plate capacitor has the following values: k = 81; d = 0.025 inches; A = 6
square inches. What is the capacitance of the capacitor?
A. 4.372 picofarad
B. 43.72 picofarad
C. 4372 picofarad
D. 437.2 picofarad
View Answer:
Answer: Option C
Solution:
6/18
316. Five picofarad is equivalent to ________.
A. 5 x 10 to the -12th
B. 50 x 10 to the -12th
C. 5 x 10 to the -10th
D. 500 x 10 to the -10th
View Answer:
Answer: Option A
Solution:
317. If two micro-farad capacitors are connected in series, what will be the total effective
capacitance?
A. 0.125 microfarad
B. 0.0624 microfarad
C. 2.5 microfarad
D. 0.50 microfarad
View Answer:
Answer: Option A
Solution:
318. A 20 μF capacitor is charged by a 12-V battery. What is the stored energy at the
capacitor?
A. 2.88 x 10^-3 J
B. 1.07 x 10^-3 J
C. 1.44 x 10^-3 J
D. 2.88 x 10^-2 J
View Answer:
Answer: Option C
Solution:
319. Which of the following characterizes inductance?
7/18
A. Tends to oppose dc
B. Tends to oppose changes in voltage
C. Tends to oppose changes in current
D. Opposes all frequencies equally
View Answer:
Answer: Option C
Solution:
320. A coil of wire wound, with or without a magnetic core designed to have a higher self-
inductance than a straight wire.
A. Inductor
B. Solenoid
C. Toroid
D. Inductive relay
View Answer:
Answer: Option A
Solution:
321. With the same voltage applied, which of the following allows more current?
A. 25 ohms
B. 250 ohms
C. 0.25 ohms
D. 2.5 ohms
View Answer:
Answer: Option C
Solution:
322. In electrical circuits, current is known as the flow of charged carriers, such as electrons.
When can this happen?
A. when an electrical force (called emf) is applied
8/18
B. when material used allows electrons to flow
C. when there is circuit continuity
D. all of the above
View Answer:
Answer: Option D
Solution:
323. What utilizes electrical energy in electrical circuits?
A. supply emf
B. load
C. the conducting wires
D. all of the above
View Answer:
Answer: Option B
Solution:
324. An electronic device draws 300 watts from its 24-volt power source. Find effective
resistance.
A. 1.92 ohms
B. 19.20 ohms
C. 1.25 ohms
D. 12.50 ohms
View Answer:
Answer: Option A
Solution:
325. A 50 Ω resistor is connected in series with a 150C resistor and to a supply voltage of 20
V. What is the current through the 50 Ω resistor?
A. 0.01 A
B. 0.1 A
9/18
C. 1.0 A
D. 10 A
View Answer:
Answer: Option B
Solution:
326. Two resistors, 10 Ω and 100 Ω are connected in parallel, approximately, what is the total
resistance?
A. 10 Ω
B. 50 Ω
C. 90 Ω
D. 100 Ω
View Answer:
Answer: Option A
Solution:
327. A shunt resistor is used to limit the load current to 0.5 A, if the load resistance is 100 Ω
and the original current is 1amp, what should be the value of the shunt resistance?
A. 25 Ω
B. 50 Ω
C. 75 Ω
D. 100 Ω
View Answer:
Answer: Option D
Solution:
328. How many 1 kΩ resistors to be connected in parallel are needed in order to get 100 Ω?
A. 2
B. 5
C. 10
10/18
D. 20
View Answer:
Answer: Option C
Solution:
329. Two resistors, R1 = 100 Ω and R2 = 200 Ω are connected in series, if the voltage
across R2 is 20 V, what is the voltage across R1?
A. 5 V
B. 10 V
C. 15 V
D. 20 V
View Answer:
Answer: Option B
Solution:
330. Two resistors, R1 = 100 Ω and R2 = 200 Ω are connected in parallel. If the current
through R1 is 1 A, what would be the current on R2?
A. 0.125 A
B. 0.25 A
C. 0.35 A
D. 0.50 A
View Answer:
Answer: Option D
Solution:
331. A 6A current source drives a load consisting a parallel combination of R1 = 50 Ω and

R2 = 25 Ω. Determine the current I1 through R1.
A. 1 amp
B. 2 amps
C. 3 amps
11/18
D. 4 amps
View Answer:
Answer: Option B
Solution:
332. A constant voltage source Vs = 60 is delivering a power to a series combination of R1 =

100 Ω, R2 = 200 Ω and R3 = 300 Ω. Calculate the voltage drop across R2.
A. 10 V
B. 20 V
C. 30 V
D. 40 V
View Answer:
Answer: Option B
Solution:
333. If 12 V are applied to a circuit that consumes 78 W, what is the current flow through the
circuit?
A. 6.5 A
B. 936 A
C. 0.15 A
D. 9.36 A
View Answer:
Answer: Option A
Solution:
334. Find the current that flows through the filament of a 400 watts flat iron connected to a
220 Volt power line.
A. 50 mA
B. 5 A
C. 5 mA
12/18
D. 500 mA
View Answer:
Answer: Option D
Solution:
335. An electrical device has a resistance of 10 Ω and is supplied with a 5 ampere constant
current source. If the deice is rated 100 Vdc, determine its power consumed.
A. 250 W
B. 450 W
C. 750 W
D. 1000 W
View Answer:
Answer: Option A
Solution:
336. The power dissipated by a 10 Ω load resistor with a current rating of 5 amperes is
_________ if supplied with a 20 volt dc potential.
A. 40 W
B. 80 W
C. 160W
D. 250 W
View Answer:
Answer: Option A
Solution:
337. The power in a circuit consisting of two equal resistors in series is known to be 10 watts.
If the two resistors are connected in parallel, what would be the circuit power dissipation?
A. 2.5 watts
B. 5 watts
C. 20 watts
13/18
D. 40 watts
View Answer:
Answer: Option D
Solution:
338. How many nodes are needed to completely analyze a circuit according to Kirchhoff’s
current law?
A. two
B. all nodes in the circuit
C. one less than the total number of nodes in the circuit
D. one
View Answer:
Answer: Option C
Solution:
339. Loop currents should be assumed to flow in which direction?
A. Straight
B. Either C or D arbitrarily selected
C. Counter-clockwise
D. Clockwise
View Answer:
Answer: Option B
Solution:
340. What theorem we should use in solving electrical circuits with several voltage sources?
A. superposition
B. Norton
C. Thevenin
D. Kirchhoff
14/18
View Answer:
Answer: Option A
Solution:
341. In a mesh, the algebraic sum of all voltages and voltage drops is equal to zero.
A. superposition theorem
B. Norton’s law
C. Kirchhoff’s first law
D. Kirchhoff’s second law
View Answer:
Answer: Option D
Solution:
342. The sum of all currents entering a junction is equal to the sum of currents leaving away
from that junction.
A. Kirchhoff’s first law
B. Kirchhoff’s second law
C. Norton’s theorem
D. Thevenin’s theorem
View Answer:
Answer: Option A
Solution:
343. Theorem used to simplify complex circuits wherein, the simplified circuit contains an
equivalent open circuit resistance and open circuit voltage.
A. Norton’s
B. Thevenin’s
C. Maxwell’s
D. Kirchhoff’s
View Answer:
15/18
Answer: Option B
Solution:
344. Considered as the reverse of Thevenin’s theorem.
A. Maxwell
B. Superposition
C. Kirchhoff
D. Norton’s
View Answer:
Answer: Option D
Solution:
345. A certain Thevenin equivalent circuit has parameters RTH = 10 Ω and VTH = 20 V. If
this is converted to Norton’s equivalent circuit, RN and IN would be
A. 10 Ω and 2 A
B. 10 Ω and 4 A
C. 0.10 and 2 A
D. 0.10 and 4 A
View Answer:
Answer: Option A
Solution:
346. RN and IN of a Norton’s equivalent circuit are known to be 100Ω and 10A, respectively.
If
a 400Ω load is connected, it will have a load current of
A. 1 A
B. 2 A
C. 3 A
D. 4 A
16/18
View Answer:
Answer: Option B
Solution:
347. A chosen closed path of current flow in a network. In making this current path there
should be no node nor elements that are passed more than once.
A. node
B. junction
C. mesh
D. loop
View Answer:
Answer: Option C
Solution:
348. A set of circuit elements that forms a closed path in a network over which signal can
circulate.
A. node
B. junction
C. mesh
D. loop
View Answer:
Answer: Option D
Solution:
349. In a network, what do we call a reference point chosen such that more branches in a
circuit met.
A. node
B. junction
C. ground
D. mesh
17/18
View Answer:
Answer: Option A
Solution:
350. A common connection between circuit elements or conductors from different branches.
A. node
B. junction
C. ground
D. mesh
View Answer:
Answer: Option B
Solution:


Subscribe
18/18
April 16, 2018

1/18
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
351. The return point in a circuit, where all voltage measurements are referred.
A. node
B. junction
C. ground
D. loop
View Answer:
Answer: Option C
Solution:
352. Mesh analysis is best used together with what circuit law?
A. KVL
B. KCL
C. VDT
D. CDT
View Answer:
Answer: Option A
Solution:
353. Nodal analysis is best used together with
A. KVL
B. KCL
C. VDT
D. CDT
View Answer:
2/18
Answer: Option B
Solution:
354. Three 100 Ω resistors are connected in a tee-form (T) network and is set up between a
100 V supply and a load resistor RL. If maximum power transfer is desired, what should be
the resistance of the load resistor RL?
A. 50 Ω
B. 75 Ω
C. 125 Ω
D. 150 Ω
View Answer:
Answer: Option D
Solution:
355. Theorem used in simplifying circuit analysis by considering the effect of supply voltages
one at a time.
A. Thevenin’s theorem
B. Norton’s theorem
C. Superposition
D. KVL
View Answer:
Answer: Option C
Solution:
356. Three resistors, R1 = 60 Ω, R2 = 80 Ω and R3 = 100 are connected in delta. If the

network is to be transformed into star, what would be the value of the resistor opposite of
R2?
A. 25.0 Ω
B. 33.3 Ω
C. 45.0 Ω
D. 56.7 Ω
3/18
View Answer:
Answer: Option A
Solution:
357. The description of two sine waves that are in step with each other going through their
maximum and minimum points at the same time and in the same direction
A. phased sine wave
B. sine waves in phase
C. sine wave in coordination
D. stepped sine waves
View Answer:
Answer: Option B
Solution:
358. Most ac-supplies are in the form of
A. sine-wave
B. square-wave
C. triangular-wave
D. rectangular-wave
View Answer:
Answer: Option A
Solution:
359. Advantage(s) of ac over dc
A. economically produced
B. transmission of ac is more efficient
C. ac voltages can be easily changed
D. all of the above
View Answer:
Answer: Option D
4/18
Solution:
360. An ac-voltage has an equation v = 240 sin120πt, its frequency is
A. 60 Hz
B. 90 Hz
C. 120 Hz
D. 240 Hz
View Answer:
Answer: Option A
Solution:
361. When can an ac-voltage, v = 120sin120πt reach its first peak?
A. 4.167 μs
B. 8.334 μs
C. 4.167 ms
D. 8.334 ms
View Answer:
Answer: Option C
Solution:
362. Calculate the period of an alternating current having an equation of I = 20sin120πt.
A. 4.167 ms
B. 8.33 ms
C. 16.67 ms
D. 33.33 ms
View Answer:
Answer: Option C
Solution:
363. The time taken by an alternating voltage, v = 100sin240πt to reach 50V for the first time
5/18
A. 358 μs
B. 695 μs
C. 358 ms
D. 695 ms
View Answer:
Answer: Option D
Solution:
364. An alternating voltage of sine-wave form has a maximum voltage of 311V. What is its
value at 225°?
A. 110 V
B. 220 V
C. -220 V
D. -110 V
View Answer:
Answer: Option C
Solution:
365. If an alternating voltage has a magnitude of 10 V at 30°, what is its maximum voltage?
A. 20 V
B. 30 V
C. 40 V
D. 50 V
View Answer:
Answer: Option A
Solution:
366. What is the frequency of an alternating current, if it reaches 90° within 4.167 ms?
A. 20 Hz
6/18
B. 30 Hz
C. 50 HZ
D. 60 Hz
View Answer:
Answer: Option C
Solution:
367. At what angle does an alternating voltage of cosine-waveform reaches its negative
peak?
A. 45°
B. 90°
C. 135°
D. 180°
View Answer:
Answer: Option D
Solution:
368. When comparing rms voltages and average voltages, which of the following statement
is true, assuming sine waves?
A. Either the rms voltage or the average voltage might be larger
B. The rms voltage is always greater than the average voltage
C. There will always be a very large difference between the rms voltage and the average
voltage
D. The average voltage is always greater than the rms voltage
View Answer:
Answer: Option B
Solution:
369. What is the average voltage of an alternating voltage, v = 100sin120πt?
A. 31.8 V
7/18
B. 63.6 V
C. 70.71 V
D. 0 (zero) V
View Answer:
Answer: Option D
Solution:
370. Determine the effective voltage of v = 100sin120πt.
A. 31.80 V
B. 35.35 V
C. 70.71 V
D. 90.00 V
View Answer:
Answer: Option D
Solution:
371. What do you mean by root-mean-squared (rms) value?
A. it is the average value
B. it is the effective value
C. it is the value that causes the same heating effect as a dc-voltage
D. B or C
View Answer:
Answer: Option D
Solution:
372. The power dissipated across the resistance in an AC circuit
A. real power
B. reactive power
C. apparent power
8/18
D. true power
View Answer:
Answer: Option D
Solution:
373. In AC circuit, resistors will dissipate what power?
A. reactive
B. passive
C. inductive
D. true
View Answer:
Answer: Option D
Solution:
374. In an ac-circuit, if the voltage and current are in phase, the circuit is
A. resistive
B. reactive
C. capacitive
D. inductive
View Answer:
Answer: Option A
Solution:
375. If the current in an ac-circuit leads the voltage by 90°, the circuit is
A. resistive
B. capacitive
C. inductive
D. purely inductive
View Answer:
9/18
Answer: Option B
Solution:
376. In a purely inductive circuit the current
A. leads the voltage by 45°
B. leads the voltage by 90°
C. lags the voltage by 90°
D. lags the voltage by 45°
View Answer:
Answer: Option C
Solution:
377. If the current and voltage in an ac-circuit has a phase difference, it would mean the load
is
A. resistive
B. capacitive
C. inductive
D. reactive
View Answer:
Answer: Option D
Solution:
378. A resistive and a capacitive load of equal magnitude is connected in series, determine
the phase difference between the voltage and the current.
A. current leads the voltage by 45°
B. current lags the voltage by 45°
C. current leads the voltage by 90°
D. current lags the voltage by 90°
View Answer:
Answer: Option A
10/18
Solution:
379. The reactance of a 25 mH coil at 500 Hz is which of the following?
A. 785 ohms
B. 785,000 ohms
C. 13 ohms
D. 0.0013 ohms
View Answer:
Answer: Option A
Solution:
380. The impedance in the study of electronics is represented by resistance and ________.
A. inductance and capacitance
B. inductance
C. reactance
D. capacitance
View Answer:
Answer: Option C
Solution:
381. A series circuit consists of an 80 mH inductor and a 150 μF capacitor. Calculate the
total reactance if it is connected to a 220-volt 60-cycle source.
A. 12.5 Ω inductive
B. 12.5 Ω capacitive
C. 47.8 Ω inductive
D. 47.8 Ω capacitive
View Answer:
Answer: Option A
Solution:
11/18
382. Ignoring any inductive effects, what is the impedance of RC series capacitor made up of
a 56 kilo ohms resistor and a 0.33 μF capacitor at a signal frequency of 450 Hz?
A. 66,730 ohms
B. 57,019 ohms
C. 45,270 ohms
D. 10,730 ohms
View Answer:
Answer: Option B
Solution:
383. A 220-volt, 60-Hz source is driving a series RL circuit. Determine the current in the
circuit if R = 100 Ω and XL = 100 Ω.
A. 1.10 A (lagging)
B. 1.55 A (lagging)
C. 2.20 A (lagging)
D. 4.40 A (lagging)
View Answer:
Answer: Option B
Solution:
384. How many electrical degrees a current will lead the voltage in a series RC load with R =
100 Ω and XC = 50 Ω?
A. 13.28°
B. 26.56°
C. 31.72°
D. 63.44°
View Answer:
Answer: Option B
Solution:
12/18
385. What will be the current equation in a series RC network if supplied with v =
Vmsin120πt source. The circuit has a power factor pf = 0.5?
A. i = Imaxsin(120πt + 60)
B. i = Imaxsin(120πt – 60)
C. i = Imaxsin(120πt + 30)
D. i = Imaxsin(120πt – 30)
View Answer:
Answer: Option A
Solution:
386. The power factor (pf) of a series LC circuit is
A. 0
B. 0.5
C. 0.75
D. 1.0
View Answer:
Answer: Option A
Solution:
387. What is the power factor (pf) of a series RL circuit having R = 50Ω and XL = 20Ω?
A. 0.63
B. 0.71
C. 0.81
D. 0.93
View Answer:
Answer: Option D
Solution:
388. A 200Ω resistor if connected in series with a capacitive reactance of 100 will give a total
circuit impedance of
13/18
A. 173.2 Ω
B. 223.6 Ω
C. 250.6 Ω
D. 300.0 Ω
View Answer:
Answer: Option B
Solution:
389. What will happen when the power factor of a circuit is increased?
A. reactive power increases
B. active power increases
C. both active and reactive powers increases
D. both active and reactive powers decreases
View Answer:
Answer: Option B
Solution:
390. A series RL network is supplied with a 200-volt, 60-cycle source. If the voltage across
the resistor R is 100 V, what is the voltage across the inductor L?
A. 0 V
B. 100 V
C. 173.2 V
D. 200 V
View Answer:
Answer: Option C
Solution:
391. A 6-Ω resistor is connected in series with a capacitive reactance of 8 Ω. If the supply
voltage is 200 V, what is the power consumed by the circuit?
A. 2400 W
14/18
B. 4000 W
C. 5000 W
D. 6666.67 W
View Answer:
Answer: Option A
Solution:
voltage is 200 V, what is the circuit current magnitude?
A. 14.28 A
B. 20 A
C. 25 A
D. 33.33 A
View Answer:
Answer: Option B
Solution:
voltage is 200 V, what is the apparent power of the circuit?
A. 1200 W
B. 2400 W
C. 3200 W
D. 4000 W
View Answer:
Answer: Option D
Solution:
394. The apparent power of a series RC network is given to be 4000 W. If R = 6 Ω, and XC =

8 Ω, calculate the true power of the network.
A. 1200 W
15/18
B. 2400 W
C. 3200 W
D. 4000 W
View Answer:
Answer: Option B
Solution:
395. A series RC circuit has an apparent power of 4000 W. If R = 6 Ω, and XC = 8 Ω,

determine the reactive power.
A. 1200 W
B. 2400 W
C. 3200 W
D. 4000 W
View Answer:
Answer: Option C
Solution:
396. A network has a true power and a reactive power of 2400 W and 3200 W respectively.
What is its apparent power?
A. 800 W
B. 1600 W
C. 4000 W
D. 5600 W
View Answer:
Answer: Option C
Solution:
397. What is the total impedance of a series circuit consisting of R = 6 Ω, XC = 8 Ω, and XL

= 16 Ω?
A. 10 Ω
16/18
B. 14 Ω
C. 24.73 Ω
D. 30 Ω
View Answer:
Answer: Option A
Solution:
398. What is the significance of connecting loads in parallel?
A. it makes power consumption less
B. it provides greater efficiency
C. it increases the safety factor
D. it allows independent operations of loads
View Answer:
Answer: Option D
Solution:
399. A parallel RL circuit with R = 60 Ω, and XL = 40 Ω has a total impedance of
A. 24.3 Ω
B. 28.3 Ω
C. 33.3 Ω
D. 38.3 Ω
View Answer:
Answer: Option C
Solution:
400. Calculate the total impedance of a parallel RC circuit if R = XC = 50 Ω.
A. 25 @ 45° Ω
B. 25 @ -45° Ω
C. 35.35 @ 45° Ω
17/18
D. 35.35 @ -45° Ω
View Answer:
Answer: Option D
Solution:


Subscribe
18/18
April 17, 2018

1/18
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
401. A 100-volt source is supplying a parallel RC circuit having a total impedance of 35.35 Ω.
Calculate the total line current.
A. 2.83 ∠ 45°
B. 2.83 ∠ -45°
C. 4.00 ∠ 45°
D. 4.00 ∠ -45°
View Answer:
Answer: Option A
Solution:
402. What is the power factor of a circuit if the inductive susceptance and conductance have
the same value?
A. 0.325
B. 0.525
C. 0.673
D. 0.707
View Answer:
Answer: Option D
Solution:
403. If a circuit has an admittance of Y = 0.2 + j0.6, the circuit is
A. purely inductive
B. inductive
C. capacitive
2/18
D. reactive
View Answer:
Answer: Option C
Solution:
404. The circuit admittance Y = 0.2 – j0.6, the circuit is
A. resistive
B. inductive
C. capacitive
D. reactive
View Answer:
Answer: Option B
Solution:
405. What is the resonant frequency of a circuit when L is 50 microhenrys and C is 40

picofarads are in parallel?
A. 7.96 MHz
B. 79.6 MHz
C. 3.56 MHz
D. 1.78 MHz
View Answer:
Answer: Option C
Solution:
406. If you need an LC circuit to be resonant at 2500 Hz and use a 150 mH coil, what should
the capacitance value be?
A. 0.027 μF
B. 0.015 μF
C. 0.15 μF
D. 27 μF
3/18
View Answer:
Answer: Option A
Solution:
407. What is the resonant frequency of a circuit when L of 3 microhenry and C of 40

picofarad are in series?
A. 1.33 MHz
B. 14.5 MHz
C. 14.5 kHz
D. 1.33 kHz
View Answer:
Answer: Option B
Solution:
408. What is the resonant frequency of a circuit when L of 25 microhenry and C of 10

picofarad are in parallel?
A. 63.7 MHz
B. 10.1 MHz
C. 63.7 kHz
D. 10.1 kHz
View Answer:
Answer: Option B
Solution:
409. A series circuit at resonance would mean, the circuit is
A. resistive
B. inductive
C. capacitive
D. reactive
View Answer:
4/18
Answer: Option A
Solution:
410. Characteristics of the current in a series R-L-C circuit at resonance.
A. It is dc
B. It is a minimum
C. It is zero
D. It is at maximum
View Answer:
Answer: Option D
Solution:
411. What is the cause of a minimum Q on a single-tuned LC circuit?
A. decreased series resistor
B. decreased shunt resistor
C. increased shunt resistor
D. decreased capacitance
View Answer:
Answer: Option C
Solution:
412. Find the half-power bandwidth of a parallel resonant circuit, which has a resonant
frequency of 3.6 MHz and a Q of 218.
A. 606 kHz
B. 58.7 kHz
C. 16.5 kHz
D. 47.3 kHz
View Answer:
Answer: Option C
5/18
Solution:
413. A parallel circuit at resonance would mean, the circuit is
A. resistive
B. inductive
C. reactive
D. capacitive
View Answer:
Answer: Option A
Solution:
414. What will happen to a parallel ac-circuit if its line frequency is more than the resonant
frequency?
A. becomes purely resistive
B. becomes purely capacitive
C. becomes inductive
D. becomes capacitive
View Answer:
Answer: Option D
Solution:
415. In a series ac-circuit, if the line frequency is more than the resonant frequency, the
circuit behaves as
A. resistive
B. inductive
C. reactive
D. capacitive
View Answer:
Answer: Option B
Solution:
6/18
416. If the line frequency of a parallel ac-circuit is less than the resonant frequency, the
circuit behaves as
A. resistive
B. reactive
C. capacitive
D. purely inductive
View Answer:
Answer: Option B
Solution:
417. If an ac-series circuit is supplied with a source whose frequency is less than that of fr,
the circuit becomes
A. resistive
B. reactive
C. inductive
D. capacitive
View Answer:
Answer: Option D
Solution:
418. _________ is a parallel LC circuit.
A. Parallel resisting circuit
B. Static circuit
C. Tank circuit
D. Hartley circuit
View Answer:
Answer: Option C
Solution:
419. A parallel LC network with L = 100 mH and C = 25 μF will resonate at what frequency?
7/18
A. 25 Hz
B. 45.5 Hz
C. 75.6 Hz
D. 100 Hz
View Answer:
Answer: Option D
Solution:
420. Absolutely, when can we say that the circuit is at resonance?
A. when XL = XC
B. when the current is minimum
C. when the voltage and current are in-phase
D. all of the above
View Answer:
Answer: Option C
Solution:
421. The description of two sine waves that are in step with each other going through their
maximum and minimum points ate the same time and in the same direction.
A. Sine waves in phase
B. Stepped sine waves
C. Phased sine waves
D. Sine waves in coordination
View Answer:
Answer: Option A
Solution:
422. Term used for the out of phase, non-productive power associated with inductors and
capacitors.
A. Effective power
8/18
B. True power
C. Reactive power
D. Peak envelope power
View Answer:
Answer: Option C
Solution:
423. Refers to a reactive power.
A. Wattles, non productive power
B. Power consumed in circuit Q
C. Power loss because of capacitor leakage
D. Power consumed in wire resistance in an inductor
View Answer:
Answer: Option A
Solution:
424. A 240 V, 25 Hz sinusoidal generator is connected to a 20 ohms resistor. Determine the

instantaneous current when elapsed time is 0.01 second.
A. 15043A
B. 16.30 A
C. 16.97 A
D. 12.00 A
View Answer:
Answer: Option D
Solution:
425. The product of current and voltage in an AC circuit refers to the
A. Real power
B. Useful power
9/18
C. Apparent power
D. DC power
View Answer:
Answer: Option C
Solution:
426. The distance covered or traveled by a waveform during the time interval of one
complete cycle.
A. Frequency
B. Wavelength
C. Time slot
D. Wave time
View Answer:
Answer: Option B
Solution:
427. The power dissipated across the resistance in an AC circuit.
A. Real power
B. Reactive power
C. Apparent power
D. True power
View Answer:
Answer: Option D
Solution:
428. It is the number of complete cycles of alternating voltage or current complete each
second
A. Period
B. Frequency
C. Amplitude
10/18
D. Phase
View Answer:
Answer: Option B
Solution:
429. How many degrees are there in one complete cycle?
A. 720 deg
B. 360 deg
C. 180 deg
D. 90 deg
View Answer:
Answer: Option B
Solution:
430. The impedance in the study of electronics is represented by resistance and _________
.
A. Reactance
B. Inductance and capacitance
C. Inductance
D. capacitance
View Answer:
Answer: Option A
Solution:
431. Two current sources deliver to a common load. The first source delivers current whose
equation is 25sin 100πt A while the second delivers a current whose equation is 15 cos
100πt A. What is the rms values of the current in the load?
A. 29.15 A
B. 40 A
C. 20.6 A
11/18
D. 10 A
View Answer:
Answer: Option C
Solution:
432. It is a rotating sector that represent either current or voltage in an AC circuit.
A. Resistance
B. Phasor
C. polar diagram
D. velocity
View Answer:
Answer: Option C
Solution:
433. The relationship of the voltage across an inductor to its current is described as
A. Leading the current by 90 deg
B. Lagging the current by 90 deg
C. Leading the current by 180 deg
D. In phase with the current
View Answer:
Answer: Option A
Solution:
434. Find the phase angle between the voltage across through the circuit when Xc is 25
ohms, R is 100 ohms and XL is 50 ohms.
A. 76 deg with the voltage leading the current
B. 24 deg with the voltage lagging the current
C. 14 deg with the voltage leading the current
D. 76 deg with the voltage lagging the current
12/18
View Answer:
Answer: Option C
Solution:
435. Calculate the period of an alternating current having a equation of I=20sin 120πt
A. 4.167 ms
B. 8.33 ms
C. 16.67 ms
D. 33.33 ms
View Answer:
Answer: Option C
Solution:
436. What do you mean by root-mean-square (rms) value?
A. It is the average value
B. It is the effective value
C. It is the value that causes the same heating effect as the DC voltage
D. b or c
View Answer:
Answer: Option D
Solution:
437. The maximum instances value of a varying current, voltage or power equal to 1.414
times the effective value of a sine wave.
A. RMS value
B. Peak value
C. Effective value
D. Peak to Peak value
View Answer:
Answer: Option D
13/18
Solution:
438. If an AC signal has a peak voltage of 55 V, what is the average value?
A. 35 V
B. 61.05V
C. 86.34 V
D. 38.89 V
View Answer:
Answer: Option A
Solution:
439. If an AC signal has an average voltage of 18 V, what is the rms voltage?
A. 12.726 V
B. 19.980 V
C. 25.380 V
D. 16.213 V
View Answer:
Answer: Option B
Solution:
440. A 220-V, 60Hz is driving a series RL circuit. Determine the current if R = 100 ohms and
20 mH inductance
A. 2.2 A (lagging)
B. 2.0 A (lagging)
C. 2.2 A (leading)
D. 2.0 A (leading)
View Answer:
Answer: Option A
Solution:
14/18
441. Ignoring any inductive effects, what is the impedance of RC series capacitor made up of
a 56K ohm resistor and a 0.33 uF capacitor at a signal frequency of 4650 Hz.
A. 66730 ohms
B. 57019 ohms
C. 45270 ohms
D. 10730 ohms
View Answer:
Answer: Option B
Solution:
442.What is the time constant of a 500 mH coil and a 3300 ohm resistor in series?
A. 0.00015 sec
B. 6.6 sec
C. 0.0015 sec
D. 0.0000015 sec
View Answer:
Answer: Option A
Solution:
443. What is the relationship between frequency and the value of XC ?
A. Frequency has no effect
B. XC varies inversely with frequency
C. XC varies indirectly with frequency
D. XC varies directly with frequency
View Answer:
Answer: Option B
Solution:
444. The reactance of a 25 mH coil at 5000 Hz which of the following?
15/18
A. 785 ohms
B. 785000 ohms
C. 13 ohms
D. 0.0012 ohms
View Answer:
Answer: Option A
Solution:
445. There are no transients in pure resistive circuits because they
A. Offer high resistance
B. Obey ohm’s Law
C. Are linear circuits
D. Have no stored energy
View Answer:
Answer: Option C
Solution:
446. The reciprocal of capacitance is called
A. Conductance
B. Elastance
C. Permitivity
D. permeability
View Answer:
Answer: Option B
Solution:
447. The AC system is preferred over DC system because
A. Ac voltages can easily changed in magnitude
B. Dc motors do not have fine speed control
16/18
C. High voltage AC transmission is less efficient
D. DC voltage cannot be used for domestic appliances
View Answer:
Answer: Option D
Solution:
448. An alternating voltage is given by v = 20 sin 157 t. The frequency of the alternating
voltage is
A. 50 Hz
B. 25 HZ
C. 100 Hz
D. 75 Hz
View Answer:
Answer: Option B
Solution:
449. An alternating current given by i = 10 sin 314 t. The time taken to generate two cycles of
current is
A. 20 ms
B. 10 ms
C. 40 ms
D. 50 ms
View Answer:
Answer: Option C
Solution:
450. In a pure resistive circuit, the instantaneous voltage and are current are given by:
v = 250sin314t i = 10sin314t
The peak power in the circuit is
A.1250 W
17/18
B. 25 W
C. 2500 W
D. 250 w
View Answer:
Answer: Option C
Solution:


Subscribe
18/18
October 3, 2018

(Last Updated On: January 8, 2021)
1/19
MCQ in Resistors
MCQ in Inductors
MCQ in Capacitors
451. Find the half power bandwidth of a parallel resonant circuit which has a resonant
frequency of 3.6 MHz and Q of 218.
A. 606 kHz
B. 58.7 kHz
C. 16.5 kHz
D. 47.3 kHz
View Answer:
Answer: Option C
Solution:
452. A current of 10 A and a pf of 0.8 lagging is taken from a single phase 250 V supply. The
reactive power of the system is_______.
A. 1500
B. 2000
C. 250
D. not
View Answer:
Answer: Option A
Solution:
453. An R-L series ac circuit has 15 V across the resistor and 20 V across the inductor. The
supply voltage is
A. 35 V
B. 5 V
C. 25 V
2/19
D. 175 V
View Answer:
Answer: Option C
Solution:
454. The active and reactive powers of an inductive circuit are equal. The power factor of the
circuit is
A. 0.8 lagging
B. 0.707 lagging
C. 0.6 lagging
D. 0.5 lagging
View Answer:
Answer: Option B
Solution:
455. Determine the power angle in the series circuit which consists of R = 25 ohms, L = 0.2
H across a power supply of 200 V, 30 Hz.
A. 36.4 degrees
B. 52.4 degrees
C. 46.4 degrees
D. 56.4 degrees
View Answer:
Answer: Option D
Solution:
456. An AC circuit has a resistance of 6 ohms, inductive reactance of 20 ohms, and

capacitive reactance of 12 ohms. The circuit power will be
A. 0.8 lagging
B. 0.8 leading
C. 0.6 lagging
3/19
D. 0.6 leading
View Answer:
Answer: Option C
Solution:
457. A 25 ohm resistor connected in series with a coil of 50 ohm resistance and 150 mH
inductance. What is the pf of the circuit?
A. 85%
B. 80%
C. 90%
D. 75%
View Answer:
Answer: Option B
Solution:
458. A current wave is represented by the equation i = 10 sin 251t. The average and RMS
value of current are
A. 7.07 A; 6.63A
B. 6.36A; 7.07A
C. 10A; 7.07A
D. 6.36A; 10A
View Answer:
Answer: Option B
Solution:
459. Calculate the susceptance in mho of a circuit consisting of resistor of 10 ohms in series
with a conductor of 0.1 H, when the frequency is 50 Hz.
A. 0.0303
B. 0.0092
C. -0.029
4/19
D. 32.95
View Answer:
Answer: Option C
Solution:
460. An inductive circuit of resistance 16.5 ohms and inductive of 0.14 H takes a current of
25 A. If the frequency is 50 Hz, the supply voltage is
A. 117.4 V
B. 1174 V
C. 1714 V
D. 1471 V
View Answer:
Answer: Option B
Solution:
461. The current taken by a circuit is 1.2 A when the applied potential difference is 250 V and
the power taken is 135 W. The power factor is
A. 0.35
B. 0.45
C. 0.55
D. 0.65
View Answer:
Answer: Option B
Solution:
462. A capacitor has a capacitance of 20 uF. The current supplied if it is placed across a
1100 V, 25 Hz supply.
A. 3.554 A
B. 6.91 A
C. 3.45 A
5/19
D. 9.61 A
View Answer:
Answer: Option B
Solution:
463. The form factor of half wave rectified signal is equal to _________.
A. 1.11
B. 0.786
C. 2.22
D. 1.57
View Answer:
Answer: Option D
Solution:
464. An impedance draws a current I = 10 cos(wt – 30) from the voltage V = 220sin(wt + 30).
What is the impedance?
A. 15.6 – j15.6
B. 15.6 + j15.6
C. 19.1- j11.1
D. 11.0 + j19.1
View Answer:
Answer: Option C
Solution:
465. The input of an a.c circuit having pf = 0.8 lagging is 20 KVA. The power drawn by the
circuit is ________ Kw.
A. 12
B. 20
C. 16
D. 8
6/19
View Answer:
Answer: Option C
Solution:
466. A capacitor connected to a 115 V, 25 Hz supply takes 5 A. What current will it take when
the capacitance and frequency are doubled?
A. 2 A
B. 5 S
C. 10 A
D. 20 A
View Answer:
Answer: Option D
Solution:
467. At what frequency will an inductor of 5mH have the same reactance as a capacitor of
0.1 µF?
A. 7.12 kHz
B. 7.12 Hz
C. 7.12 MHz
D. 7.12 Ghz
View Answer:
Answer: Option A
Solution:
468. What capacitance must be placed in series with an inductance of 0.05H, so that when
the frequency is 100 Hz, the impedance becomes equal to the ohmic resistance?
A. 70.5 uF
B. 50.7 uF
C. 5.7 uF
D. 7.05 uF
7/19
View Answer:
Answer: Option B
Solution:
469. A 220 V, 60 Hz source is driving a series RL circuit. Determine the current in the circuit if
R = 100 ohm XL = 100 ohm.
A. 1.10 lagging
B. 1.55 lagging
C. 2.20 lagging
D. 4.40 lagging
View Answer:
Answer: Option B
Solution:
470. What is the resonant frequency of a circuit when an inductance of 1 uH and capacitance
of 10 Picofarad are in series?
A. 15.9 MHz
B. 50.3 MHz
C. 15.9 kHz
D. 50.3 KHz
View Answer:
Answer: Option B
Solution:
471. The __________ the Q of a circuit, the narrower the bandwidth.
A. Lower
B. Higher
C. Broader
D. Selective
View Answer:
8/19
Answer: Option B
Solution:
472. A 5 microfarad capacitor is discharged suddenly through a coil having an inductance of

2 H and a resistance of 200 ohms. The capacitor is initially charge to a voltage of 10 volts.
Find the additional resistance required just to be prevent oscillation.
A. 1625 ohms
B. 1065 ohms
C. 1265 ohms
D. 1025 ohms
View Answer:
Answer: Option B
Solution:
473. The rate of rise of current through an inductive coil is maximum
A. after 1 time constant
B. at the start of current flow
C. near the final maximum value of current
D. at 63.2% of its maximum steady state value
View Answer:
Answer: Option D
Solution:
474. A coil of 15 H inductance and 10 ohms resistance is suddenly connected to a 20 volts

DC source by closing the switch. The value of current 2 seconds after the switch is closed is
A. 1.74 A
B. 1.47 A
C. 1.17 A
D. 1.71 A
View Answer:
9/19
Answer: Option B
Solution:
475. A DC voltage of 80 volts is applied to a circuit containing a resistance of 80 ohms in

series with an inductance of 20 Henry. Calculate the growth of current at the instant of
completing the circuit.
A. 4 A/s
B. 2 A/s
C. ½ A/s
D. ¼ A/s
View Answer:
Answer: Option A
Solution:
476. A 200 volt DC supply is suddenly switched to a relay coil which has a time constant of 3
ms. If the current in the coil reaches 0.20 ampere after 3 ms determine the steady state
value of the current.
A. 0.361 A
B. 0.163 A
C. 0.316 A
D. 0.631 A
View Answer:
Answer: Option C
Solution:
477. A relay has a resistance of 300 ohms and is switched to a 100 V DC supply. If the
current reaches 63.2% of its final value at 0.02 sec, determine the inductance of the circuit.
A. 5 H
B. 6 H
C. 4 H
D. 13 H
10/19
View Answer:
Answer: Option B
Solution:
478. Energy stored by a coil is doubled when its current is increased by ________ percent.
A. 100
B. 141.4
C. 50
D. 25
View Answer:
Answer: Option B
Solution:
479. A 60 volt potential difference is suddenly applied to a coil of inductive 60 mH and

resistance 180 ohms. At what rate is it rising after 0.005 sec?
A. 322 A/sec
B. 223 A/sec
C. 22.3 A/sec
D. 32.2 A/sec
View Answer:
Answer: Option B
Solution:
480. A voltage rise linearly form zero to 100 volts in 1 second, falls instantaneously to zero at
t = 1 second and remains zero thereafter. This voltage is applied to an RL series circuit in
which R = 5 ohms and L = 100 mH. What is the current when t = 0.50 second?
A. 6.90 A
B. 96 A
C. 9.60 A
D. 69 A
11/19
View Answer:
Answer: Option C
Solution:
481. A capacitance of 10 microfarad is connected in series with a resistance of 8,000 ohms.

If the combination is suddenly connected to a 100 V DC supply. Find the initial rate of rise in
potential across the capacitor.
A. 12500 V/s
B. 125 V/s
C. 1250 V/s
D. 12.50 V/s
View Answer:
Answer: Option B
Solution:
482. A 25 microfarad capacitor is connected in series with a 0.50 M-ohm resistor and a 120
volt storage battery. What is the potential difference in the capacitor 6 sec after the circuit is
closed?
A. 64 volts
B. 46 volts
C. 4.60 volts
D. 6.40 volts
View Answer:
Answer: Option B
Solution:
483. A capacitor of 2 microfarad with an initial charge q0 is connected across the terminals of
a 10 ohm resistor and the switch is closed at t = 0. Find q0 (micro-coulomb) if the transient
power in the resistor is known to be PR = 360e-10^(-5)t
A. 1200
B. 120
C. 102
12/19
D. 2100
View Answer:
Answer: Option B
Solution:
484. The transient current in a loss-free L-C circuit when excited from an ac source is
_________ a/an sine wave .
A. overdamped
B. undamped
C. underdamped
D. critically damped
View Answer:
Answer: Option B
Solution:
485. A series RLC circuit with R = 5 ohms, L = 0.10 H, C= 500 microfarad has a constant
voltage V = 10 volts applied at t = 0. Find the resulting transient current.
A. 0.707e-50t sin 139t
B. 0.272e-25t sin 278t
C. 0.720e-25t sin 139t
D. none of these
View Answer:
Answer: Option C
Solution:
486. A circuit consisting of 20 ohms resistor, 20 mH inductor and a 100 microfarad capacitor
in series is connected to a 200 V DC supply. The capacitor is initially uncharged. Find the
maximum instantaneous current.
A. 6.45 A
B. 7.45 A
C. 8.45 A
13/19
D. 9.45 A
View Answer:
Answer: Option A
Solution:
487. A time of 10 ms is required for the current in an RL circuit to reach 90% of its final value.
If R is 10 ohms, find the value of C to be inserted in series with the RL circuit so that the
frequency of oscillation of the resulting current is 1000 cycles per second.
A. 5.38 x 10-8 Farad
B. 5.83 x 10-7 Farad
C. 5.83 x 10-6 Farad
D. 5.83 x 10-5 Farad
View Answer:
Answer: Option B
Solution:
488. A series RLC circuit with R = 1 kΩ, L = 1 H and C = 6.25 μF is suddenly connected
across a 24 V dc source. At t = 0, i= 0 and q = 0. Determine the current after 0.01 sec.
A. 3.45 mA
B. 4.61 mA
C. 5.40 mA
D. 5.05 mA
View Answer:
Answer: Option C
Solution:
489. A series RLC circuit has R = 200 Ω, L = 0.1 H and a capacitor C = 10 μF. If a 100 V dc
source is connected across the terminals of the series circuit at t = 0, determine the current
after 1 millisecond. Assume zero initial conditions.
A. 0.353 A
B. 0.229 A
14/19
C. 0.253 A
D. 0.368 A
View Answer:
Answer: Option D
Solution:
490. Double energy transient are produced in circuits consisting of
A. two or more resistors
B. resistance and inductance
C. resistance and capacitance
D. resistance, inductance and capacitance
View Answer:
Answer: Option D
Solution:
491. A DC voltage source is connected across a series RLC circuit, under steady state
conditions, the applied DC voltage drops entirely across the
A. R only
B. L only
C. C only
D. R & L combinations
View Answer:
Answer: Option C
Solution:
492. Consider a DC voltage source connected to a series RC circuit. When the steady state
reaches, the ratio of energy stored in the capacitor to the total energy supplied by the voltage
source is equal to
A. 0.362
B. 0.500
15/19
C. 0.632
D. 1.00
View Answer:
Answer: Option B
Solution:
493. An inductor at t = 0 with initial current I0 acts as
A. short
B. open
C. current source
D. voltage source
View Answer:
Answer: Option C
Solution:
494. An inductor L carries steady state current I0, suddenly at time t = 0 the inductor is
removed from circuit and connected to a resistor R. The current through the inductor at time t
is equal
A. I0e-Rt/L
B. I0 (1-e-Rt/L)
C. I0e+Rt/L
D. I0 (1-e+Rt/L)
View Answer:
Answer: Option A
Solution:
495. Transient current in a circuit results from
A. voltage applied to the circuit
B. impedance of the circuit
C. changes in the stored energy in inductors and capacitors
16/19
D. resistance of the circuit
View Answer:
Answer: Option C
Solution:
496. A two terminal black box contains a single element which can be R, L, C or M. As soon
as the box is connected to a dc voltage source, a finite non-zero current is observed to flow
through the element. The element is a/an
A. resistance
B. inductance
C. capacitance
D. Mutual inductance
View Answer:
Answer: Option B
Solution:
497. In a circuit the voltage across an element is v(t) = 10 (t – 0.01)e-100t V. The circuit is
A. un-damped
B. under damped
C. critically damped
D. Over damped
View Answer:
Answer: Option C
Solution:
498. A unit step voltage is applied at t = 0 to a series RL circuit with zero initial conditions
A. It is possible for the current to be oscillatory
B. The voltage across the resistor at t = 0+ is zero
C. The energy stored in the inductor in the steady state is zero
D. The resistor current eventually falls to zero
17/19
View Answer:
Answer: Option B
Solution:
499. A 1 µF capacitor charged through a 2 kΩ resistor by a 10 V dc source. The initial growth

of capacitor voltage will be at the rate
A. 316 V/ms.
B. 5.0 V/ms
C. 6.32 V/ms
D. 10.0 V/ ms
View Answer:
Answer: Option B
Solution:
500. A series R-C circuit has a capacitor with an initial voltage of 11 V. A 15 V dc source is
now connected across the R-C circuit. The initial rate of change of capacitor voltage can be
A. 15 Χ 0.368 / RC
B. 15Χ 0.632 / RC
C. 11/RC
D. 4/RC
View Answer:
Answer: Option D
Solution:

18/19

Subscribe
19/19

Ece Nga Reviewer

Uploaded by

Copyright:

Available Formats

Ece Nga Reviewer

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ece Nga Reviewer

Uploaded by

Copyright:

Available Formats

MCQ in Electrical Circuit Part 1 | ECE Board Exam

December 21, 2013

Prev Article Next Article

MCQ Topic Outline included in ECE Board Exam Syllabi

MCQ in AC-DC circuits

Start with Part 1 of the Practice Exam Test Questions Series

Choose the letter of the best answer in each questions.

1. Conventional flow assumes charges flow from

2. Electron flow assumes charges flow from

3. Series resonance occurs when

4. The symbol Q refers to

5. The ratio of W/VA in an ac circuit means

6. What is the reciprocal of quality factor?

A. Positive or negative ions

C. Ions that are lighter in weight than electrons

8. VL = VC in a series RLC circuit when

A. The value of the impedance is minimum

B. The power factor is zero

C. The current leads the total voltage by 90˚

D. The total voltage is zero

10. Property of an electric circuit that dissipates electric energy

11. What is the other name of relative permittivity?

D. Specific inductance capacity

12. In a series RLC circuit

A. The current lags VL by 90˚

B. The current leads VL by 90˚

13. Resistor with colored bands in the body

14. In a resonant circuit, if Q ≥ 10 resonant frequency __________ bandwidth.

C. The power factor is one

D. Distance between plates

18. In an ac circuit with inductive reactance, the

A. Phase angle of the circuit is always 45˚

C. Current through the inductance lags its induced voltage by 90˚

D. Current through the inductance and voltage across it are180˚ out-of-phase

20. What is the specific resistance of a pure germanium?

22. In a series RLC circuit

A. Increasing the frequency decreases the resistance

B. Increasing the frequency increases the resistance

C. Both XL and XC change as frequency changes

D. Impedance will always decrease

24. Kirchhoff’s laws (KCL and KVL) are applicable to

D. Passive networks alone

25. A tank circuit is a

26. A capacitive load always has a ________ power facto

27. What is the temperature coefficient of the resistance Eureka?

28. As applied to a series RLC circuit, bandwidth means

A. The frequency range for maximum power transfer

C. The separation of the half-power points

D. The frequency at which XL = XC

29. Which is considered as the effect of a dielectric material?

D. Increasing the distance between the plates

32. If resonant frequency is 10 kHz and quality factor is 50, then

33. Which statement is true?

A. A series resonant circuit is of high impedance

B. A parallel resonant circuit is of low impedance

D. A parallel resonant circuit is inductive if it operates at a frequency higher than the

34. What is considered as the most important value of a sine wave?

35. An ac series circuit is composed of a resistance of 20 Ω, inductive reactance of 40 Ω,

37. The value of temperature coefficient (α) is dependent upon