Omm 320D2 Xba

3/27/23, 11:06 PM SIS 2.
2019/05/21 Maintenance Interval Schedule (SEBU9247-10)
SMCS - 7000 i07766998

Ensure that all safety information, warnings, and instructions are read and understood
PC
before any operation or any maintenance procedures are performed.
P-0
The user is responsible for the performance of maintenance. All adjustments, the use of proper
202 00
lubricants, fluids, filters, and the replacement of components due to normal wear and aging are
3 3
06: /03/2 785E
included. Failure to adhere to proper maintenance intervals and procedures may result in diminished
performance of the product and/or accelerated wear of components.
0
SEB 6:10- 8
Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, in
order to determine the maintenance intervals. Products that operate in severe operating conditions may
U
© 2 924 7:000
require more frequent maintenance. Refer to the maintenance procedure for any other exceptions that
may change the maintenance intervals.
023 7
Note: Before each consecutive interval is performed, all maintenance from the previous interval must
be performed.
Cat
erp
Note: If Cat HYDO Advanced hydraulic oils are used, the hydraulic oil change interval is extended to
illa
6000 hours. S·O·S services after 3000 hours is strongly recommended. Consult your Cat dealer for
details.
r In
When Required c.
Air Conditioner/Cab Heater Filter (Recirculation) - Inspect/Replace
Battery - Recycle
Battery or Battery Cable - Inspect/Replace
Bucket Linkage - Inspect/Adjust
Bucket Tips - Inspect/Replace
Bucket Tips - Inspect/Replace
Cab Air Filter (Fresh Air) - Clean/Replace
Camera - Clean/Adjust
Circuit Breakers - Reset
Engine Air Filter Primary Element - Clean/Replace
Engine Air Filter Secondary Element - Replace
Film (Product Identification) - Clean
Fuel System - Prime
Fuses - Replace
High Intensity Discharge Lamp (HID) - Replace
Oil Filter - Inspect
https://sis2.cat.com/#/print-preview/service/%257B%2522title%2522%253A%2522Maintenance%2520Interval%2520Schedule%2520(SEBU9247-10)… 1/5
3/27/23, 11:06 PM SIS 2.0
Radiator Core - Clean

Track Adjustment - Adjust
Window Washer Reservoir - Fill
Window Wiper - Inspect/Replace
Windows - Clean
Every 10 Service Hours or Daily for First 100 Hours

Boom and Stick Linkage - Lubricate
Bucket Linkage - Lubricate
Every 10 Service Hours or Daily

Cooling System Coolant Level - Check
Engine Oil Level - Check
Fuel Filter Change Indicator - Inspect
Fuel System Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Hydraulic System Oil Level - Check
Indicators and Gauges - Test
Seat Belt - Inspect
Track Adjustment - Inspect
Travel Alarm - Test
Undercarriage - Check
Every 10 Service Hours or Daily for Machines Used in Severe

Applications
Every 50 Service Hours or Weekly

Quick Coupler - Lubricate
Every 100 Service Hours or 2 Weeks

Every 100 Service Hours or 2 Weeks for Machines Used in

Severe Applications
Every 100 Service Hours of Continuous Hammer Use

3/27/23, 11:06 PM SIS 2.0
Oil Filter (Hydraulic Hammer) - Replace
Initial 250 Service Hours

Engine Valve Lash - Check
Final Drive Oil - Change
Hydraulic System Oil Filter (Case Drain) - Replace
Hydraulic System Oil Filter (Pilot) - Replace
Hydraulic System Oil Filter (Return) - Replace
Swing Drive Oil - Change
Every 250 Service Hours

Engine Oil Sample - Obtain
Final Drive Oil Sample - Obtain
Cooling System Coolant Sample (Level 1) - Obtain
Every 250 Service Hours or Monthly

Belt - Inspect/Adjust/Replace
Condenser (Refrigerant) - Clean
Final Drive Oil Level - Check
Swing Bearing - Lubricate
Swing Drive Oil Level - Check
Every 250 Service Hours of Partial Hammer Use (50% of

Service Hours)
Oil Filter (Hydraulic Hammer) - Replace

Initial 500 Hours (for New Systems, Refilled Systems, and

Converted Systems)
Every 500 Service Hours

Hydraulic System Oil Sample - Obtain
3/27/23, 11:06 PM SIS 2.0
Swing Drive Oil Sample - Obtain
Every 500 Service Hours or 3 Months

Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Fuel Tank Cap and Strainer - Clean

Service Hours)

Hydraulic System Oil - Change
Every 1000 Service Hours or 6 Months

Battery - Clean
Battery Electrolyte Level - Check
Battery Hold-Down - Tighten
Engine Valve Lash - Check
Swing Drive Oil - Change

Service Hours)
Every 2000 Service Hours or 1 Year

Final Drive Oil - Change
Receiver Dryer (Refrigerant) - Replace
Swing Gear - Lubricate
3/27/23, 11:06 PM
terp
SIS 2.0
Every Year illa

r In
Every 3 Years After Date of Installation or Every 5 Years After c.
Date of Manufacture
Seat Belt - Replace
Every 6000 Service Hours or 3 Years

Cooling System Coolant Extender (ELC) - Add
Every 12 000 Service Hours or 6 Years

Cooling System Coolant (ELC) - Change
PCP-0003785E
2023/03/28
06:06:07-07:00
i06281537
© 2023 Caterpillar Inc.

Omm 320D2 Xba

Uploaded by

Copyright:

Available Formats

Omm 320D2 Xba

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Omm 320D2 Xba

Uploaded by

Copyright:

Available Formats

3/27/23, 11:06 PM SIS 2.

2019/05/21 Maintenance Interval Schedule (SEBU9247-10)

SMCS - 7000 i07766998

Radiator Core - Clean

Every 10 Service Hours or Daily for First 100 Hours

Every 10 Service Hours or Daily

Every 10 Service Hours or Daily for Machines Used in Severe

Every 50 Service Hours or Weekly

Every 100 Service Hours or 2 Weeks

Every 100 Service Hours or 2 Weeks for Machines Used in

Every 100 Service Hours of Continuous Hammer Use

Oil Filter (Hydraulic Hammer) - Replace

Initial 250 Service Hours

Every 250 Service Hours

Every 250 Service Hours or Monthly

Every 250 Service Hours of Partial Hammer Use (50% of

Every 250 Service Hours of Continuous Hammer Use

Initial 500 Hours (for New Systems, Refilled Systems, and

Every 500 Service Hours

Swing Drive Oil Sample - Obtain

Every 500 Service Hours or 3 Months

Every 500 Service Hours of Partial Hammer Use (50% of

Every 600 Service Hours of Continuous Hammer Use

Every 1000 Service Hours or 6 Months

Every 1000 Service Hours of Partial Hammer Use (50% of

Every 2000 Service Hours or 1 Year

Every Year illa

Every 6000 Service Hours or 3 Years

Every 12 000 Service Hours or 6 Years

You might also like