Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 69 views

    Untitled

    Uploaded by

    aldairlopes

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd

    Untitled

    Uploaded by

    aldairlopes
    69 views13 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    69 views13 pages

    Untitled

    Uploaded by

    aldairlopes

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    You are on page 1of 13
    BS EN 10149-2:2013 EUROPEAN STANDARD. EN 10149-2 NORME EUROPEENNE EUROPAISCHE NORM September 2013 Ics 77,140.50 Supersedes EN 10149-2:1995 English Version Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels Produits plats laminés & chaud en acters & haut limite Warmgowalate Flacherzeugnisge aus Stahlen mit hoher € asticité pour formage a rod Partie 2: Condtions Streckgrenze zum Kaltumformen - Tell 2: Technisene techniques delvraison des aciers obtenus par laminage LUsferdeaingungen for thermomechanisch gewalzte Stahle thermomécanique ‘This European Standard was approved by CEN on 17 August 2013, CEN members are bound to comply with the CENICENELEC intemal Regulations which stipulate the conditions for giving this European ‘Standard the status of 2 national standard without any alteration. Up-to-date Ists and bibliographical references concering such national standards may be oblained on application tothe CEN-CENELEC Management Cente or to ary CEN member ‘This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibilty of a CEN member into is own language ane notified to the CEN-CENELEC Management Centre nas the same status asthe ofial versions CEN members ao the national standards bodies of Ausvia, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estoria, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, reland, Waly, Latvia, Lihuania, Luxembourg, Malia, Netnerlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom aa! EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEE FUR NORMUNG CEN-CENELEC Management Contre: Avenue Mamix 17, 61000 Brussels © 2013 CEN All rghts of exploitation in any form and by any means reserved Ret. No EN 10149-2:2019: E worldwide for CEN national Members. BS EN 10149-2:2013 EN 10149-2:2013 (E) Contents Page Foreword. 1 Scope 2 Normative references 4 3 Terms and definitions 4 Information to be supplied by the purchaser 4 44° General. 42 Options 5 Dimensions, mass and tolerances. 5.1 Dimensions and tolerances... 5.2 Mass of steel. 6 Classification and designation 64 62 7 Technical requirements 7.4 Steel manufacturing process 5 7.2 Delivery condition. 7.3 Chemical composition .. 7.4 Mechanical properties. 7.5 Technological properties . 7.5.1 Weldabilit 7.5.2 Formabilit 7.6 Surface finis! 7.7 Internal soundness . 8 _ Inspection and testing. 7 8.1 General. 8.2 Sampling. 83 Test units. 8.4 Verification of chemical composition... 8.5 Preparation of samples and test pieces. 86 — Test methods. 8.7 Retests and resubm ion for testing 8.8 Inspection documents... 9 Marking 8 10 Disputes. 11 Options 8 Annex A (normative) Location of test pieces 4M Annex B (informative) Minimum inside bend radii for cold forming 2 Bibliography 13 BS EN 10149-2:2013 EN 10149-2:2013 (E) Foreword This document (EN 10149-2:2013) has been prepared by Technical Committee ECISS/TC 103 “Structural steel other than reinforcements’, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2014, and conflicting national standards shall be withdrawn at the latest by March 2014, Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10149-2:1995, In comparison with EN 10149-2:1995, the following significant technical changes were made: — Scope was modified; — subclause 6.1 was revised; — subclause 7.4.1 was modified; — subclause 7.5.3 was completely revised; — Option 13) was added in Clause 11; — steel grades S900MC and S960MC were added in Tables 1, 2 and B.1 — footnotes f and g were added in Table 2. The tiles of the other Parts of this European Standard are: — Part 4: General technical delivery conditions; — Part 8: Technical delivery conditions for normalized or normalized rolled steels, According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom, BS EN 10149-2:2013 EN 10149-2:2013 (E) 1 Scope This European Standard, in addition to EN 10149-1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming. The grades are given in Table 1 (chemical composition) and Table 2 (mechanical properties) and are supplied in the thermomechanically rolled delivery condition as given in 7.2. The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of — 1,5 mm to 20 mm for the steels which have a specified minimum yield strength of 315 MPa up to and including 460 MPa", — 1,5 mm to 16 mm for the steels which have a specified minimum yield strength of 500 MPa" up to and including 700 MPa’; and — from 2 mm up to 10 mm for the steels with a minimum yield stress in the range from 900 MPa” to 960 MPa’ 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10029, Hot-rolled plates 3 mm thick or above - Tolerances on dimensions and shape EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape EN 10149-1:2013, Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions EN ISO 14713-2:2009, Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10149-1:2013 apply. 4 Information to be supplied by the purchaser 41 General ‘The information to be supplied by the purchaser shall be in accordance with EN 10149-1 1) 1MPa= 1 Nimm? BS EN 10149-2:2013 EN 10149-2:2013 (E) 4.2. Options The options given in EN 10149-1 and Clause 11 shall apply. 5 Dimensions, mass and tolerances 5.1 Dimensions and tolerances The dimensions and tolerances shall be in accordance with EN 10149-1. For hot rolled plate tolerances, the basic requirements shall be in accordance with EN 10029, including thickness tolerances to class A, unless otherwise agreed at the time of the order. For plates cut from continuously hot rolled strip, the thickness tolerances shall be in accordance with EN 10051 5.2. Mass of steel The calculated mass of steel shall be determined in accordance with EN 10149-1 6 Classification and designation 6.1. Classification The steel grades S315MC, S355MC, $420MC, S460MC, SS00MC and S550MC of this European Standard are alloy quality steels and the steel grades S600MC, S650MC, S700MC, S900MC and S960MC of this European Standard are alloy special steels according to EN 10020. 6.2 Designation The designation shall comply with EN 1049-1 7 Technical requirements 7.1 Steel manufacturing process The steel manufacturing process shall be in accordance with EN 10149-1 See EN 10149-1:2013, Clause 11, option 1) 7.2. Delivery condition The products shall be supplied in the thermomechanically rolled delivery condition. The surface protection of descaled products shall be in accordance with EN 10149-1 See EN 10149-1:2013, Clause 11, option 2) 7.3 Chemical composition The requirements of EN 10149-1 shall apply. BS EN 10149-2:2013 EN 10149-2:2013 (E) ‘The chemical composition determined by ladle analysis shall comply with the specified values of Table 1 See EN 10149-12013, Clause 11, option 3). 7.4 Mechanical properties 744 General Under the inspection and testing conditions as specified in Clause 8 and in the delivery condition as specified in 7.2, the mechanical properties shall comply with the values given in Table 2 Heating of grades S900MC and S960MC above 400°C is not recommended. If the purchaser intends to heat grades S800MC and S960MC at temperatures above 400°C, the mechanical properties after such heating should be agreed at the time of order. See EN 10149-1:2013, Clause 11, option 13). 7.42 Impact energy If agreed at the time of the order, the verification of the impact energy value shall be carried out in accordance with EN 10149-1 See EN 10149-12013, Clause 11, option 5). 7.5 Technological properties 7.5.1. Weldability Weldability shall be in accordance with EN 10149-1 7.5.2. Formal 7.5.2.1 General NOTE Recommendations regarding cold forming are laid down in CEN/TR 10347. The products supplied according to this standard are not suitable for hot forming, 75.2.2 Cold forming 75.2.24 General Annex B contains indicative values for the inside bend radil for cold forming 7.5.2.2.2 Flangeability The products are suitable for flanging without cracking. 7.5.2.2.3 Roll forming The suitability for roll forming shall be in accordance with EN 10149-1 ‘See EN 10149-1:2013, Clause 11, option 6). BS EN 10149-2:2013 EN 10149-2:2013 (E) 7.5.3 Hot-dip zine-coating For grades S315MC to S70OMC, requirements for chemical composition of steels to be hot-dip zinc coated shall be separately agreed between manufacturer and purchaser. EN ISO 1461 should be used to specify coating requirements. EN ISO 14713-2 provides further guidance, including information on the influence of various factors, including steel chemical composition, on the coating formation, Option 7) (see EN 10149-1:2013, Clause 11) can be used to order steels with a chemical composition required for hot-dip zinc coating. When option 7) is implemented, the purchaser and manufacturer shall agree with a steel composition (ladle analysis) of silicon and phosphorous according to either Category A (or steels satisfying the formula Si < 0,03 % and Si+2.5P < 0,09 %) or Category B (limited to 0,14 % < Si < 0,25 %) or Category D (limited to 0,25 % < Si < 0,35 %) with required values as cited by the ranges given in EN ISO 14713-2:2009, Table 1, column 2. NOTE _ENISO 14713-2:2009, Table 1, gives guidance on typical coating characteristics associated with certain stee! ‘compositions on the basis of the surface composition of silicon and phosphorous. In some cases, steels above $460 may be sensitive to cracking during galvanizing and therefore special care should be taken. 7.6 Surface finish The surface finish shall be in accordance with EN 10149-1 See EN 10149-1:2013, Clause 11, option 8). 7.7. Internal soundness The internal soundness shall be in accordance with EN 10149-1. See EN 10149-1:2013, Clause 11, option 9). 8 Inspection and testing 8.1 General The products shall be supplied in accordance with EN 10149-1:2013, 8.1. Soe EN 10149-1:2013, Clause 11, option 10). 8.2 Sampling ‘Sampling shall be in accordance with EN 10149-1 8.3 Test units The test unit shall be in accordance with EN 10149-1 8.4 Verification of chemical composition The verification of the chemical composition shall be in accordance with EN 10149-1 ‘See EN 10149-1:2013, Clause 11, option 4). BS EN 10149-2:2013 EN 10149-2:2013 (E) 8.5 Preparation of samples and test pieces 85.1 General ‘The preparation of samples and test pieces shall be in accordance with EN 10149-1 8.5.2 Proparation of samples ‘The following samples shall be taken from one sample product of each test unit — one sample in the longitudinal direction for tensile testing; — one sample in the transverse direction for the bend test; — one sample sufficient for one set of six impact test pieces (if an impact test is agreed at the time of the order, see EN 10149-1:2013, 7.4.2.1) See EN 10149-1:2013, Clause 11, option 5). See Annex A, 8.6 Test methods The test methods shall be in accordance with EN 10149-1 8.7 Retests and resubmission for testing Retests and resubmission for testing shall be in accordance with EN 10149-1, 8.8 Inspection documents The inspection documents shall comply with EN 10149-1 9° Marking The marking shall comply with EN 10149-1. ‘See EN 10149-1:2013, Clause 11, option 11). 10 Disputes In case of disputes EN 10149-1 applies. 11 Options ‘See EN 10149-1:2013, Clause 11, options 1) to 11). 412) The sulphur content shall be max. 0,010 % (ladle analysis) (see Table 1) 13) The values of the mechanical properties after heating of S800MC and S960MC at temperatures above 400 °C shall be agreed at the time of the order (see 7.4.1) BS EN 10149-2:2013 EN 10149-2:2013 (E) Table 1 — Chemical composition of the ladle analysis for thermomechanically rolled steels Designation of steel] ¢ ] Mn | si | P s [a [uml v] t [mo] 6 oade wl] we | % | %~ | % | torr lx) x)» lw | % max.| max. | max. | max. | max. | % | max.| max. max. | max. Stee! | Steel name | number saree | 1.0972 [0,12 1,30 | 050 | 0,025 | o,020°| 0,015 [o,09"]0,20°| 015° | - - sassmc | 1.0976 | 0,12) 1,50 | 050 | 0,025 | 0,020" | 0,015 |o,09*/0,20°| 015° | - - sazome | 1.0980 | 0,12) 1,60 | 050 | 0,025 | 0,015" | 0,015 |o,09*/0,20°| 015° | - - sasomc | 1.0982 | 0,12) 1,60 | 0,50 | 0,025 | 0,015" | 0,015 |o,09"/0,20"| 0,15" | - - ssoome | 1.0984 | 0,12) 1,70 | 0.50 | 0,025 | 0,018" | 0,015 Jo,09*/0,20°| o,15° | - - sssomc | 1.0986 | 0,12) 1,80 | 050 | 0,025 | 0,018" | 0,015 Jo,09*/0,20"| 015° | - - seoomc | 1.8969 | 0,12] 1,90 | 0,50 | 0,025 | 0,015°| 0,015 |0,09*}0,20°| 0,22* | 0,60 | 0,005, sesomc | 1.8976 | 0,12] 2,00 | 0,60 | 0,028 | 0,015° | 0,015 |0,09°}0,20°| 0,22° | 0,50 | 0,005 s7oomc | 1.8974 | 0,12] 2,10 | 0,60 | 0.025 | 0,015" | 0,015 }o,09°I0,20"| 0,22* | 0,50 | 0.005 sgoomc | 1.8798 | 0,20] 2,20 | 0,60 | 0.025 | 0,010 | 0.015 } 0,09] 0,20] 0,25 | 1,00 | 0.005 sseomc | 1.8799 | 0,20] 2,20 | 060 | 0,025 | 0,010 | 0,015 | 0,09] 0,20] 0.25 | 1,00 | 0,005 F The sum of Nb, V and Ti shall be max. 0,22 %. f° tfagreed at the time of the order the sulphur content shall be max. 0,010 % (ladle analysis). See Clause 11, option 12) BS EN 10149-2:2013 EN 10149-2:2013 (E) Table 2 — Mechanical properties for thermomechanically rolled steels Designation of stee! | Minimum yield] _ Tensile Minimum percentage elongation | Bending grade strongth Ray | strength Ry at fracture A at 180" wpa" Mpat'* %* minimum Nominal thickness in mm mandrel diameter steel | Stee! name | number <3 23 Lo= 80 mm 1, = 5,65 \So ‘satsme | 1.0972 315 390-510 20 24 or Sa55MC | 1.0976 355 430 - 550 19 23 ost ‘sazome | 1.0980 420 480 - 620 16 19 o,st ‘sasomc | 1.0982 460 520-870 14 "7 t ssoomc | 1.0984 500 950 - 700 12 14 tt ss5omc |} 1.0986 550 600-760 12 14 18¢ ssoomc | 1.8969 600 650 - 820 " 13 18¢ sesomc | 1.8976 650° 700 - 880 10 12 at s7oome | 1.8974 700° 750 - 950 10 12 at s900mc | 1.8798 900 930 - 1.200 7 8 af s960mc | 1.8799 960 980 - 1.250 6 7 of The values for the tensile test apply to longitudinal test pieces. The values for the bend test apply to transverse test pieces, thickness in mm of test piece for bend test, For thicknesses > & mm the minimum yield strength can be 20 MPa" lower. 1MPa = 1Nimm?, Bending at 90°, for thicknesses less than 3 mm minimum mandrel diameter 7t Bending at 90°, for thicknesses less than 3 mm minimum mandrel diameter 8t 10 BS EN 10149-2:2013 EN 10149-2:2013 (E) Annex A (normative) Location of test pieces This annex gives the location of test pieces. Table A.1 — Location of test pieces Dimensions in milimetres Type oftest | Thickness | Orientation of the test | Distance of the test piece from the rolled surface of product | pieces for widths of < 600 2600 Tension <20 | tongitudinal | tongitudinal I Bend =20__| transverse _| transverse Impact >12 | longitudinal | tongitudinal ° Rolled surface. " BS EN 10149-2:2013 EN 10149-2:2013 (E) 12 Annex B (informative) Minimum inside bend radii for cold forming Table B.1 — Minimum inside bend radii for cold forming Designation of steel Minimum recommended i bend radii grade thicknesses (fin mm Steel Steel number ts3 3

    You might also like