APPENDIX-!

(1) AP/DEC 2019/BQS601/QSM601/QSB621

CONFIDENTIAL

GENERAL NOTE : -

1. ALL DESIGNS, SPECIFICATIONS AND INFORMATIONS DOCUMENTED ON

THIS DRAWINGS MAY SUBJECT TO CHANGES DUE TO SITE CONDITIONS,
LOCAL AUTHORITIES REQUIREMENTS AND DESIGN COORDINATIONS FOR
THE PURPOSE OF THE COMPLETION OF THE PROJECT.

WATER DEMAND

NO BUILDING UNIT WATER DEMAND (LPD) WATER DEMAND

WAREHOUSE

1. - WATER CLOSET 4 180 720 LPD

2. - SINK 4 90 360 LPD

TOTAL 1080 LPD

PELAN LOKASI
TANPA SKALA

NOTES :

1. THESE DRAWINGS ARE TO BE READ INCONJUNCTION

WITH ARCHITECTURAL DRAWINGS.

2. ALL LEVELS SHOWN ARE IN METRE.

3. FOR ROAD CROSSING STEEL PIPE TO BS 534 WITH INTERNAL
CEMENT LINING SHALL BE USED.

4. CONTRACTOR SHALL OBTAIN APPROVAL AND PAY ANY CHARGES

FOR EXCAVATION OF EXISTING ROAD PAVEMENT.
5. ANCHOR BLOCK AND THRUST BLOCK SHALL BE PROVIDED AT ALL
JUNCTION AND BEND.

6. MINIMUM COVER OF MS PIPE UNDER ROAD PAVEMENT

SHALL BE 1200mm.
7. FOR PIPE CROSSING OVER CULVERT DRAIN
STEEL PIPE WITH AIR VALVE SHALL BE USED.
8. ALL PIPES AND FITTINGS SHALL SUBJECT TO THE APPROVAL OF
SYARIKAT AIR MELAKA BERHAD.

9. EXACT. LOCATION OF AIR VALVE AND SCOUR VALVE

SHALL BE DECIDED ON SITE.

10. CONTRACTOR SHALL BE LIASE WITH SYABAS ON CONSTRUCTION

OF WATER PIPE RECTICULATION AND PAY ALL RELEVANT
CHARGES AS IMPOSED BY SYARIKAT AIR MELAKA BERHAD.
11. TAP = 150mm 0 MS PIPE TAPPED FROM MAIN LINE.
12. BULK METER AND STOPCOCK TO BE INFRONT
AND OUTSIDE FENCING.
13. Dl OR STEEL PIPE WILL BE USED AT ROAD AND
CULVERT CROSSING.
14. AIR VALVES, SCOUR VALVES AND SLUICE VALVES WILL BE
FIXED ON SITE WHERE NECESSARY.
15. VALVE CHAMBERS TO BE APPROVED BY
SYARIKAT AIR MELAKA BERHAD.

LEGENDS :

BOUNDARY 6.

7.
2. F.F.L +50.25 FINISHED FLOOR LEVEL

F.R.L +50.00 FINISHED ROAD LEVEL

4. 150mm Dio. M.S. PIPE (HYDRANT)

5 75mm Di0_ MS p|pE (SUPPLY)

universiti
Teknologi
Mara
CONFIDENTIAL
Hak Cipta Universiti Teknologi MARA
 APPENDIX 1 (2) AP/DEC 2019/BQS601/QSM601/QSB621
CONFIDENTIAL

BARREL BARREL SADDLE PLATE

OD OD L H
NOMINAL DIA. D1 D2 (mm) (mm) X THICKNESS
(mm) (mm) (mm) (mm)
K = L - R Tan. fr
100 x 100 121.9 121.9 550 270 -
-

12 mm THK. x 125 LONG PLATE.

1
4 Nos. TIE BOLT.
177.3 177.3 600 290
150 x 150 -
-

L1 = K + ( R + 0D_) Tan fr.

2 6
200 x 150 232.2 177.3 750 320 -
-

\ 0 L2 = ( 2R + OD ) Tan fr_ B BJ
232.2 750 370 6
200 x 200 232.2 -
-

250 x 150 286 177.3 860 350 - • -

L3 = K + ( R + QPJ Ton Jt
2 6
400
2 Nos. 12 mm THK. STIFFENER
250 x 200 286 232.2 860 -
-

L4 = ( 2R - OD ) Tan fr WITH 6 mm THK. FILLET WELD.

6
250 x 250 286 286 860 400 - -

SECTIONAL VIEW OF PIPE

300 x 150 345.4 177.3 1050 380 - -

TYPF 1
300 x 200 345.4 232.2 1050 430 - -
cussl^D PLAIN ENDED BEND WITH TIE COUPLING
61 • TO 90'
286 1050 430 NOTE :
300 x 250 345.4 - -

1. ALL DIMENSIONS ARE IN MILLIMETRE U.N.O

300 x 300 345.4 345.4 1050 480 - -

2. FOR STRAIGHT PIPES WITH PUDDLE COLLAR, THE PUDDLE

SADDLE PLATE COLLAR THICKNESS SHALL BE 25 thk. AND THE O.D OF
350 x 150 399.3 177.3 1200 400
PUDDLE COLLAR SHALL BE O.D OF PIPE PLUS 150
- -

350 x 200 399.3 232.2 1200 450 - -

350 x 250 399.3 286 1200 500 - -

350 x 300 399.3 345.4 1200 500 - -

350 x 350 399.3 399.3 1200 500 -

-

TABLE FOR PLAIN ENDED BEND L/2 L/2 SECTION

PLAN
DIAMETER TYPE 1 TYPE 2 TYPE 3 PLAIN ENDED TEE - 15 AT MEAN TEMPERATURE

2 Nos. 12 mm THK. STIFFETNER WITH MECHANICAL COUPLING

PLATE 6 mm THK. FILLET WELD.
thk. UP TO 12 mm THK. x 125 LONG PLATE 20 DIA. TIE BOLT (4 No.)
31* TO 45- 46' TO 60' 61- TO 90"
(mm) 30* 8 mm THK. FILLET WELD
ND OD
MS. PLATE-
(mm) (mm)
L R L R L R L
CONCRETE LINING
(mm) (mm) (mm) (mm) (mm) (mm) (mm)
- WATER MAINS

100 121.9 175 150 200 150 250 150 300

220
150 177.3 225 225 300 225 300 225 400

200 232.2 300 350 350 350 400 350 550

250 286 375 375 450 375 500 375 650 100 mm Dia. PIPE

300 345.4 450 525 550 525 600 525 800

350 399.3 450 600 600 600 600 600 850

400 453.1 450 675 600 450 600 450 850 840 DIA.
850
SECTION B - B
450 507 450 750 600 500 600 500

500 560.3 450 825 650 550 600 550 850 SECTION A - A TIE COUPLING AND MECHANICAL JOINT DETAILS
600 667 550 975 750 650 750 650 1000

DRAWING TITLE SUBJECT: DRAWN BY AFIQ

PROJECT

msmmm PIPE FITTING DETAILS

MEASUREMENT OF
CHECKED BY

SCALE NOT TO SCALE

Universiti PROPOSED ONE STOREY WAREHOUSE ON
CONSTRUCTION
LOT PT 777 , MELAKA WORKS V
DATE DECEMBER 2019

Teknologi COURSE CODE:

DRAWING NO. :PPUB/BQS601/QSM601/QSB621/DEC 2019/2
Mara BQS601 /QSM601 / QSB621

CONFIDENTIAL
)Hak Cipta Universiti Teknologi MARA
CONFIDENTIAL APPENDIX 1 (3) AP/DEC 2019/BQS601/QSM601/QSB621

inimum cover to pipe inimum cover to pipe

1200mm in open ground 500mm in open ground

TYPE B
TYPICAL BEDDING DETAILS
TYPE A Class 'C' concrete in
150mm bed and hall

WATER MEIER WATER METER

SHORT PIECE SINGLE FLANGED SHORT PIECE SINGLE FLANGED

CONSTANT ROW VALVE CONSTANT ROW VALVE

STRAIGKIENER DOUBLE RANGED STRAIGHTENER DOUBLE RANGED

T-POT STRAINER DOUBLE FLANGED T-POT STRAINER DOUBLE RANGED

TYPE B DUCTILE IRON TYPE B DUCTILE IRON TYPE B DUCTILE IRON TYPE B DUCTILE IRON
SLUICE (GATE) VALVE. SLUICE (GATE) VALVE. SLUICE (GATE) VALVE. SLUICE (GATE) VALVE.

W SHORT 9ff SHORT

RADIUS BEND RADIUS BEND

300mm WIDTH x 100mm THK. 3O0mm WIDTH x 100mm THK.

GRADE 25 CONCRETE APRON GRADE 25 CONCRETE APRON
WITH ONE LAYER OF BRC A10. WITH ONE LAYER OF BRC A10.

ROW OUT ROW IN ROW OUT

ROW IN

M.S PIPE L-M.S PIPE

M.S PIPE M.S PIPE-
FLANGED SOCKET RANGED SOCKET

RANGED SOCKET RANGED SOCKET

BULK METER(SUPPLY) BULK METER(HYDRANT)

SCALE : NTS

PROJECT DRAWING TITLE SUBJECT: DRAWN BY AFIQ

CHECKED BY \~M
BEDDING DETAILS
MEASUREMENT OF
Universiti PROPOSED ONE STOREY WAREHOUSE ON BULK METER DETAILS
CONSTRUCTION
SCALE NOT TO SCALE

PT 777 , MELAKA DATE DECEMBER 2019

Teknologi COURSE CODE:
WORKS V

DRAWING NO. : PPUB/BQS601/QSM601/QSB621/DEC2O19/3

Mara BQS601 / QSM601 / QSB621

CONFIDENTIAL
)Hak Cipta Universiti Teknologi MARA
CONFIDENTIAL APPENDIX 1 (4) AP/DEC 2019/BQS601/QSM601/QSB621

100mm « INLET PILLAR

FIRE HYDRANT WITH
65mm t DOUBLE OUTLET
80 400 80
COMPLETE WITH CAP AND CHAIN

PILLER HYDRANT (TO BE PAINTED YELLOW) 6mm Thk. CHEQUERED PLATE

WITH A STRIP OF 5mm THK. ROUND AND
TOP PORTION WITH ILLUMINIUOS PAINT

UFTlNG RING

CI LENGTHENER

100 dia. MS RANGE AND —

10 thk. MS CHEQUERED PLATE
SECTION OF SECTION OF PLAIN ENDED STRAIGHT PIPE
STIFFENED AND BRACE PLATE WITH FLANGE ADAPTOR
INTERMEDIATE UNIT BOTTOM UNIT TO BE PAINTED INTERNALLY AND
EXTERNALLY AS SPECIFIED
SCALE 1 : 5 SCALE 1 : 5
100mm t DUCK FOOT BEND
ON CONCRETE SUPPORT

550 x 550 x 400 MASS -

25 x 25 x 6 thk. ANGLE GALVANISED MS HINGE -WATER I
CONCRETE THRUST BLOCK
2 nos. PER CHEQUERED
PLATE COVER)
^••.•.•^-vy^y^w--,: •,v»,vy>^*v.^^*v*v^A

DETAIL OF PRECAST CHAMBER COVER SECTION A-A

SCALE1 : 5 (SLUICE VALVE PILLAR HYDRANT)
12 did. BAR TO BE WELDED
TO MS ANGLE FRAME AT 225
INTERMITTENT CRS.

SECTION OF TOP UNIT

SCALE1 : 5

- 6 dia. BARS
100 dia. MS FLANGE AND PLAIN ENDED - -SERVICE MAIN
STRAIGHT PIPE WITH PUDDLE COLLAR

\A - e 3 TrTfrfT
IktSl 3- a} m^
-CONCENTRIC TEE

-Mechanical Joint
LA i y^f^—r •
r-r -f \ w l AJ
I + I I -1 w T I •
I

I -L
80 320 80 I ! I
I I
I

SLUICE VALVE CHAMBER

K.T.S
FIRE HYDRANT WITH PRECAST CHAMBER

80 320
M.S Chequered Plote

PLAN FOR REINFORCEMENT FOR IB.mimmm.

I Grd. Lev.

PRECAST CHAMBER

Flange Adaptor Joint =b Precast Chamber

Puddle Flange
1000 Long PE Steel Pipe -Mechanical Joint

ffl- S
-EZ
m mtmm. $®mmm

SECTION A-A
IIS

PROJECT DRAWING TITLE : SUBJECT: DRAWN BY AFIQ

CHECKED BY MM
DETAILS OF PRECAST CHAMBER
PROPOSED ONE PROPOSED STOREY WAREHOUSE MEASUREMENT OF SCALE AS SHOWN
Universiti ON LOT PT 777 , MELAKA
DETAILS OF FIRE HYDRANT
CONSTRUCTION
DATE DECEMBER 2019
Teknologi COURSE CODE:
WORKS V

DRAWING NO. iPPUB/BQS601/QSM601/QSB621/DEC 2019/4

/[ARA BQS601 / QSM601 / QSB621

CONFIDENTIAL
)Hak Cipta Universiti Teknologi MARA
CONFIDENTIAL APPENDIX 1 (5) AP/DEC 2019/BQS601/QSM601/QSB621

MAXIMUM LENGTH IN METRES

TYPE OF
CROSSING
DIA. OF PIPE A B

100-150 10.40 8.00

TYPICAL DRAIN &
COLLAR JOINT - 200-800 12.50
CULVERT CROSSING 14.90
TYPE 1
900 12.40 10.00

Lx FALL 1:500 MIN

NOTE :

GROUND LEVEL DIMENSION "B" ASSUMES MINIMUM THICKNESS

FOR STEEL PLATE AS IN BS 534 APPENDIX A

^4, ^>^>^> '<m$3z

STUB END (for HDPE) -
STEP COUPLING (for D.I) STUB END (for HDPE)
STEP COUPLING (for D.l)

MS SHORT PIECE
MS WASHOUT TEE

THRUST BLOCK AS PER

STANDARD DRAWING

TYPICAL CULVERT (DETAIL FOR HDPE OR D.l PIPES WITH

STEEL OVERCROSSING)

"YPICAL CULVERT CROSSING TYPE 1

62
,62,100 ,62,

75

m
6mm • M.S BARS -

zn u
i 150 150 ,

ffl i
'

12
—

50
I
1

SCOUR VALVE
100

SLUICE VALVE
' ,25,
AIR VALVE

ELEVATION
SLUICE VALVE SCOUR VALVE AIR VALVE SECTION

MARKER POST

PROJECT DRAWINGTITLE SUBJECT: DRAWN BY AFIQ

CHECKED BY
TYPICAL CULVERT CROSSING &
MEASUREMENT OF
universiti PROPOSED ONE STOREY WAREHOUSE ON MARKER POST
CONSTRUCTION
SCALE NOT TO SCALE

PT 777 , MELAKA DATE DECEMBER 2019

Teknologi COURSE CODE:
WORKS V

DRAWING NO. : PPUB/BQS601/QSM601/QSB621/DEC2019/5

Mara BQS601 / QSM601 / QSB621

CONFIDENTIAL
)Hak Cipta Universiti Teknologi MARA