CYLINDERS

CYLINDERS
DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

8
CYLINDERS

DESIGN FEATURES & MATERIALS

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

ALL SEALS ARE BUNA-N TEMPERA- BRASS OR STAINLESS TUBING PRECISION HONED (16 EXTREMELY LOW FRICTION,
TURE RANGE OF -40°F to +250°F. MICRO OR BETTER) FOR SIZE AND ROUNDNESS WITH LONG LIFE NYLON, SNAP-IN
CROSS HATCH LUBRICANT RETAINING PATTERN BEARING
LONG LIFE STEEL LEATHER BACK-UP RING
SWIVEL BUSHING AIDS IN KEEPING ROD
CLEAN

SCREW MACHINED HIGH HIGH TENSILE ALUMINUM GROUND AND POLISHED

TENSILE ALUMINUM HEADS PISTON (SEE PISTON SEAL 416 STAINLESS STEEL
CONSTRUCTIONS BELOW) RODS WITH WRENCH FLATS

FIELD-PROVEN LOCK NUT SECURELY HOLDS PISTON TO ZINC PLATED HARDENED RETAINING
ROD. 7/8” & 1-1/8” BORES HAVE PISTONS THREADED RINGS, GROUND FLAT AND PARALLEL,
ONTO ROD SEALED WITH LOCTITE® & STAKED HOLD HEADS SQUARE TO BORE

BASIC CONSTRUCTION (DOUBLE ACTING)

TYPE A SINGLE ENDED • All Type “A” Cylinders, These all-pur-
pose units are used for most pneumatic applications.
Optional Double Rod Packings are recommended for heavy duty
and hydraulic applications, not available on 7/8” & 1-1/8” Bores.
FOR DIMENSIONS & MOUNTS SEE PAGES 17 - 21
Pressure Rating: 150 P.S.I. Pneumatic, 350 P.S.I. Hydraulic.
Breakaway: Approximately 5 to 8 P.S.I.
Bore Sizes Available: 7/8”, 1-1/8”, 1-1/2”, 2”, 2-1/2”, 3”.
FOR DIMENSIONS AND MOUNTS
TYPE C SINGLE ENDED • Type “C” Cylinders are constructed SEE PAGES 17 thru 21.
using low friction “U” Cup Seals and include a wear strip on the
piston with the exception of the 4”(it has no wear strip). These
Cylinders are primarily used on low pressure
applications and where low minimum breakaway is required.
Pressure Rating: 150 P.S.I. Pneumatic only.
Breakaway: Approximately 2 to 3 P.S.I.
Bore Sizes Available: 7/8”, 1-1/8”, 1-1/2”, 2”, 2-1/2”, 3 & 4”.
TYPE E SINGLE ENDED • Type “E” Cylinders are constructed
FOR DIMENSIONS AND MOUNTS
using Block-Vee Seals and include double rod seals in the front
SEE PAGES 17 thru 21.
head except on the 7/8” & 1-1/8” Bores. A heavy duty wear strip
(bearing) on the piston minimizes friction and piston seal wear side
load conditions prevents metal-to-metal contact. These Cylinders
are generally used on low pressure hydraulics and where side load
conditions are present.
Pressure Rating: 200 P.S.I. Pneumatic, 500 P.S.I. Hydraulic.
Breakaway: Approximately 10 to 15 P.S.I.
Bore Sizes Available: 7/8”, 1-1/8”, 1-1/2”, 2”, 2-1/2”, 3” & 4”.
5” BORE AVAILABLE-Consult Factory for Details. FOR DIMENSIONS AND MOUNTS
SEE PAGES 17 thru 21.
9
 CYLINDERS

STANDARD VARIATIONS OF TYPES A, C & E

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

The basic construction of these standard variations is respectively identical to

Types “A”, “C” or “E”, except where noted.

DOUBLE ENDED: TYPES AD, CD & ED

These Cylinders are constructed with a common
single rod, which protrudes from both ends. As one
end retracts, the other extends.
Bore Sizes Available: 7/8”, 1-1/8”, 1-1/2”, 2”,
2-1/2”, 3” & 4”.
Maximum Stroke Available: 65”.
NOTE: Due to piston construction, 3/32” of stroke is
lost on Type AD 1-1/2”, 2”, 2-1/2” and 3” bore sizes.

BACK-TO-BACK: TYPES ABB, CBB & EBB

These units consist of two separate single ended
Cylinders, joined together by a common rear head.
Their strokes can be either identical or different. By
fastening one rod end to a fixed object, these units
can perform as 3 and 4 position Cylinders.
Bore Sizes Available: 7/8”, 1-1/8”, 1-1/2”, 2”,
2-1/2”, 3” & 4”.
NOTE: Options must be indicated for each stroke.

INTEGRAL REAR SWIVEL: TYPES AN, CN & EN

These Cylinders are constructed with a female clevis
end, including clevis pin.
Bore Sizes Available: 7/8”, 1-1/8”, 1-1/2”, 2”,
2-1/2”, 3” & 4”.
NON ROTATING - TYPE AR
Internal guide rods.
Bore Sizes Available: 2”, 3”and 4”
INTEGRAL SQUARE HEAD:
TYPES AS, CS & ESPES
TYPES ASD, CSD & ESD
These units incorporate the use of square heads, thus
eliminating the need for separate Foot Mounts.
Bore Sizes Available: 7/8”, 1-1/8”, 1-1/2”, 2”.
NOTE: Due to piston construction, 3/32” of stroke is
lost on Type ASD 1-1/2” and 2” bore sizes.
10
CYLINDERS

Port
THREE POSITION: #3

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

TYPES: AP, CP & EP SINGLE ENDED
TYPES: APD, CPD & EPD DOUBLE ENDED Port
These Cylinders feature two separate piston rod #2
assemblies which provide three definite and positive
positions. Any combination of first stroke and total stroke
is available. Both rods fully retracted is first position. Port
Port #1 Extends rod first stroke to second position. #1
Port #2 Extends rod full stroke to third position.
Port #3 Retracts both rods to first position.
When ordering, second stroke must be specified as
total stroke, as second Cylinder rod moves through both
strokes. For example, if first stroke required is 4” and
second stroke is 2”, order should read: FOR DIMENSIONS & MOUNTS
AP-3x4x6. 6” being the total stroke (4+2). SEE PAGES 17 - 21
Bore Sizes Available: 1-1/2”, 2”, 2-1/2”, 3” & 4”.
NOTE: Options must be indicated for each stroke.

TANDEM:
TYPE: ET SINGLE ENDED
TYPE: ETD DOUBLE ENDED
The basic construction of these Cylinders is identical to
Type “E” and feature two Cylinders in tandem having
two pistons mounted on one common rod. Pneumatic
operation with hydraulic control can be obtained by
operating the rear Cylinder pneumatically and filling
the front Cylinder with oil and piping its ports in series
using a flow control valve. The output force of a single
Cylinder can be almost doubled using a Tandem Cylin-
der and piping both rear ports together and both front
ports together, which will apply the working pressure to
both Cylinders at the same time. This is particularly use-
ful when space limitations preclude the use of large bore
Cylinders, and the force required is greater than that
supplied by smaller bore units. FOR DIMENSIONS & MOUNTS
Bore Sizes Available: 1-1/2”, 2”, 2-1/2”, 3” & 4”. SEE PAGES 17 - 21
Maximum Stroke Available:
Type “ET”: 60”.
Type “ETD”: 40”.
ORDERING PROCEDURE
EXAMPLE: E-3 x 4-BC-HTP-IB-OS-RG NOTE: When ordering
BC.............................Cushion Both Ends back-to- back and three
HTP............................High Temperature (Viton) Seals position cylinders, options must
IB .............................AB Accessory Pin installed in both ends be specified for each cylinder.
OS ............................Oversized Rod All mounts are ordered
RG ............................Outboard Rod Guide installed separately. See pages 20 & 21.
11
 CYLINDERS

ALL STAINLESS STEEL CYLINDERS

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

DESIGNED TO SOLVE CORROSION & ENVIRONMENT PROBLEMS

BY MANUFACTURING ALL METAL PARTS FROM 300 SERIES STAINLESS STEEL

TYPES : SSA, SSE, SSAN, SSEN, SSAP, SSEP, SSABB, SSEBB, SSET SINGLE ENDED

TYPES : SSAD, SSED, SSAPD, SSEPD, SSETD DOUBLE ENDED

ALL Cylinder parts are manufactured from type 300 series stainless steel. Otherwise, they are
identical in construction to our standard Types “A”, “AD”, “E” & “ED” Cylinders. Units are partic-
ularly recommended for use in the food and dairy industries and in highly corrosive atmospheres,
such as found in the marine and chemical field.

Maximum Stroke Available: 130”

Bore Sizes Available: 7/8”, 1-1/8”, 1-1/2”, 2”, 2-1/2”, 3” & 4”.
For Stainless Steel Mounts consult factory.

REQUEST A COPY OF CATALOG NUMBER SS200 COVERING OUR COMPLETE

LINE OF 300 SERIES STAINLESS STEEL CYLINDERS.

FOR CUSHIONS, FOR SPRING RETURN,

SPECIFY: SPECIFY:
FC (FRONT CUSHION) SRF INDICATES SPRING IN FRONT END (AIR PUSH)
RC (REAR CUSHION) ROD NORMALLY RETRACTED
BC (CUSHION BOTH ENDS) SRR INDICATES SPRING IN REAR END (AIR PULL)
ROD NORMALLY EXTENDED

HIGH TEMPERATURE SEALS

SPECIFY HTP

NOTE: Stainless Steel Mounting Nuts available upon request.

For Special Options consult factory.
12
CYLINDERS
• OPTIONS
FAIL SAFE • SPRING RETURN - SINGLE ACTING

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

Available in all previous models except Types “ET” & “ETD”. MAXIMUM STROKE AVAILABLE IS 10”. These Cylinders
can be supplied with the rods either normally retracted or extended by the spring. On SRF models, Front Head Rod
Seals are normally not provided, but can be if requested.
SPECIFY:
SRF INDICATES SPRING IN FRONT END (AIR PUSH) ROD NORMALLY RETRACTED
SRR INDICATES SPRING IN REAR END (AIR PULL) ROD NORMALLY EXTENDED
SRFW INDICATES OPTIONAL STRONGER SPRING (For heavy duty applications only.)
SRRW INDICATES OPTIONAL STRONGER SPRING (For heavy duty applications only.)

APPROXIMATE SPRING FORCES IN POUNDS

AT REST FULL STROKE
Bore Sizes Piston Rod
Std. Spring Stronger Spring Std. Spring Stronger Spring
7/8” STD 9 X 24 X
1-1/8” STD 17 29 40 58
• OS 19 30 45 60
1-1/2” STD 17 30 41 58
•OS 18 52 45 100
2” STD 17 52 42 100
•OS 21 77 47 125
2-1/2” STD 25 77 55 125
•OS 30 X 75 X
3” STD 23 77 50 125
• OS 31 X 73 X
4” STD 57 X 123 X
• OS 75 X 175 X

Notes: Applies to SRF and SRFW models only.

CUSHIONS LAST 1/2 INCH OF STROKE IS EFFECTIVELY CUSHIONED TO REDUCE SHOCK &
SPECIFY: NOISE. FULL REVERSE FLOW PROVIDED. CYLINDER LENGTH NOT AFFECTED.
FC (FRONT CUSHION) CUSHION ADJUSTING SCREW LOCATIONS
RC (REAR CUSHION)
SINGLE ENDED DOUBLE ENDED
BC (CUSHION BOTH ENDS)
BORE SIZES
DIM.
1-1/2” 2” 2-1/2” 3” 4”
A 1/2 7/16 1/2 1/2 13/16
B 1-3/4 2 2-5/16 2-5/8 3-1/16

NOTES:
1) Dim. B cushion screw shown fully closed.
2) Not available on Spring Return Cylinders.
3) Non-Standard Cushion Adjusting Screw
locations available at slight additional cost.

BORE SIZES
CUSHION
CYLINDER TYPES 1-1/8” 1-1/2” 2-1/2 “
LOCATION 7/8” 1-1/8” 1-1/2” 2” 2” OS 2-1/2 “ 3” thru 4”OS
OS OS OS
FRONT ALL TYPES (Except those below) NA FX NA ADJ FX ADJ FX ADJ ADJ ADJ
TYPES AN, CN & EN ONLY NA FX NA FX NA ADJ FX ADJ ADJ ADJ
REAR ALL TYPES (Except those below) NA FX FX ADJ FX ADJ ADJ ADJ ADJ ADJ
TYPES AN, CN & EN ONLY NA FX FX FX NA ADJ ADJ ADJ ADJ ADJ
TYPE CD ONLY - NA FX NA ADJ NA NA NA NA NA ADJ
NOTES:
ADJ = ADJUSTABLE CUSHION AVAILABLE
1) Fixed Cushions are INTERNAL.
FX = FIXED CUSHION ONLY AVAILABLE
2) Tandem Cylinders - Cushions installed on Rear Cylinder Only.
NA = NO CUSHION AVAILABLE
3) Three Position Cylinders - Rear Cushion of Front Cylinder not available. 13
 CYLINDERS
• OPTIONS
DOUBLE ROD PACKING
DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

SPECIFY: DRP Two sets of rod seals in “A” Type cylinders - except 7/8” and 1-1/8” bore sizes.
___________________________________________________________________________________________________________________

FAIL SAFE
SPECIFY: FS Spring installed in cylinder to retract rod should there be an air failure.
Dimensions are those of a Single Acting Cylinder.
___________________________________________________________________________________________________________________

HIGH TEMPERATURE SEALS

SPECIFY: HTP Fluorocarbon compound (Viton) seals, temperature range of +10°F to +350°F .
___________________________________________________________________________________________________________________

HOLLOW RODS
SPECIFY: M Hole thru rod available up to 12” stroke.
ROD DIA. 3/8” 1/2” 5/8” 3/4” 1” 1-1/4”
HOLE SIZE 3/16” 1/4” 5/16” 7/16” 9/16” 5/8”
___________________________________________________________________________________________________________________

NO TANG
SPECIFY: NT Cylinders available without Tang section (covered by dimension “E” minus “N”).
___________________________________________________________________________________________________________________

OVERSIZED ROD
SPECIFY: OS Larger diameter rod for column loading. Not available on Type ETD-11/2” bore.
BORE SIZE 7/8” 1-1/8” 1-1/2” 2” 2-1/2” 3” 4”
ROD DIA. N/A 1/2” 5/8” 3/4” 1” 1” 1-1/4”
___________________________________________________________________________________________________________________

LOW FRICTION CYLINDER

SPECIFY: LF Available in “A” Type cylinders only. For extremely low friction at medium to high pressure.
___________________________________________________________________________________________________________________

MAGNETIC PISTON
SPECIFY: RM To signal Hall Effect or Reed switches. Available on Type “A”&“E” cylinders.
___________________________________________________________________________________________________________________

ROD WIPER
SPECIFY: WR Teflon wiper replaces the standard leather back-up ring in Types “A” & “E” cylinders only.
___________________________________________________________________________________________________________________

POLYURETHANE BUMPERS
SPECIFY: PUBF For use on high speed Cylinder applications to reduce shock and noise
PUBR Where standard cushions can not be used. Made of 1/2” thick
PUBB Polyurethane and press fit between the head and piston

PUBF BUMPER INSTALLED IN FRONT • PUBR BUMPER INSTALLED IN REAR

PUBB BUMPER INSTALLED BOTH ENDS
Available on all Type Cylinders and Bore sizes except Spring Return Cylinders and Cylinders
having Accessory Pins, Bleeder Valves or Cushions. Adds 1/2” of length for each bumper.
___________________________________________________________________________________________________________________

14 ACCESSORIES: For valuable complementary accessories used with Allenair Cylinders see pages 42 - 45.
CYLINDERS
• OPTIONS
HALL EFFECT SWITCHES (CSA “NRTL/C” Listed): ALLENAIR Hall Effect switches are designed to be used with our type

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

“A”&“E” 1-1/8”thru 4” bore cylinders. The cylinders must be ordered with the “RM” option (adds 1” O.A.L. to “A” type).
All switches have an LED indicator light, nine (9) foot leads, and an operating temperature range of - 22°F to +176 °F.
TECHNICAL DATA
MODEL FUNCTION SWITCHING SWITCHING SWITCHING SWITCHING SPEED VOLTAGE DROP
VOLTAGE CURRENT POWER
H01 NORMALLY OPEN 6-24/DC 1 Amp max. 24 watts max. 1.5 ms operate 0.5 Volts
PNP output 0.5 ms release
H02 NORMALLY OPEN 6-24/DC 1 Amp max. 24 watts max. 1.5 ms operate 0.5 Volts
NPN output 0.5 ms release
H03 NORMALLY OPEN 12-24-50/60 600mA max. 5 Amp 15 watts max. 1.5 ms operate 1 Volt
TRIAC output inrush 0.5 ms release
H04 NORMALLY OPEN 120-50/60 600mA max. 5 Amp 72 watts max. 1.5 ms operate 1 Volt
TRIAC output inrush 0.5 ms release
NOTES:
2 2 AWG/P V C
1) PNP output is Sourcing 1 .2 7 ca ble 1 .0 5
2) NPN output is Sinking
All models require a mounting strap purchased as a
separate item based on the cylinder bore size. .9 5 .8 5

CYLINDER BORE SIZE STRAP NO. R MB 2

bra cket
1-1/8” & 1-1/2” RMS1
2” & 2-1/2” RMS2
3” RMS3
4” RMS4

REED SWITCHES (CSA “NRTL/C” Listed)

S T R AP
ALLENAIR Reed switches are designed to be used
with our “A”&“E” type 1-1/8” thru 4” bore cylinders. Cylinders must be ordered with the “RM” option (adds 1” O.A.L.
to “A” type). All switches have nine (9) foot hook up cable. Operating temperature range is - 22°F to +176°F. Models
R02, R04 and R05 have an LED indicator light. Models R02, R03, R04 and R05 have MOV surge suppression.
TECHNICAL DATA
MODEL FUNCTION SWITCHING SWITCHING SWITCHING SWITCHING SPEED VOLTAGE
VOLTAGE CURRENT POWER DROP
R01 NORMALLY OPEN 0-240/DC 1 Amp max. 30 watts max. 0.6 ms operate 0 Volts
SPST 0-240-50/60 0.05 ms release
R02 NORMALLY OPEN 5-240/DC 1 Amp max. 30 watts max. 0.6 ms operate 3 Volts
SPST 5-240-50/60 .005 Amp min. 0.05 ms release
R03 NORMALLY OPEN 10-240-50/60 4 Amp max. 50 100 watts max. 0.6 ms operate 1 Volt
TRIAC OUTPUT Amp Inrush 0.05 ms release
NORMALLY OPEN 4 Amp max. 0.6 ms operate
R04 24-240-50/60 100 watts max. 1 Volt
TRIAC OUTPUT 50 Amp Inrush 0.05 ms operate
0.005 Amp min.
R05 NORMALLY OPEN 5-120/DC 0.5 Amp max. 10 watts max. 0.5ms operate 3.5 Volts
SPST 5-120-50/60 0.005 Amp min. 0.1ms release

Models R01 - R04 include mounting bracket P/N RMB2.

Order mounting strap based on cylinder bore size as shown below.
CYLINDER BORE SIZE 1-1/8” & 1-1/2” 2” & 2-1/2” 3” 4”
STRAP PART NO. RMS1 RMS2 RMS3 RMS4

Model R05 supplied with a universal mounting bracket and strap covering all bore sizes (1-1/8 thru 4”) P/N RMB1

STANDARD OPTIONS FOR ALL TYPES & BORE SIZES EXCEPT WHERE NOTED. (AVAILABLE AT EXTRA COST.)
15
 CYLINDERS
• OPTIONS
REED SWITCHES
DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

Models R01 - R04 Model R05

2 2 AWG/P V C .5 3
1 .2 7 ca ble 1 .0 5

.9 5 .8 5 .3 7 .9 2

R MB 2
bra cket 2 4 AWG/P V C
ca ble

1 .0
R MB
.4 3 univ ers a l
bra cket
S T R AP

MODIFICATIONS : PLEASE CONSULT FACTORY SPECIFY

Listed below are some of the many modifications Allenair makes daily.
RODS:
Non-Standard Rod Extensions (“H” Dim.) Length Required
Non-Standard Rod Threads (“CC” Dim.) Size Required
Non-Standard Rod Thread Length (“J” Dim.) Length Required
Female Threads In R ed
No Thre ead
Complete ed
Non-Standard Wrench Flats Location & Size
Special Rod Materi ed
HEADS:
Non-Standard Port Location(s) Print Required
Non-Standard Cushion Screw Location(s) Print Required
Extra Ports Print Required
Non-Standard Hole In Tang Size & Location Required
NOTE: The Port Sizes shown in the dimension drawings are the largest available.
LISTED BELOW ARE SPECIAL CODES WE USE WHENEVER A SPECIAL CYLINDER (CS) IS ORDERED.
NOT ALL CODES ARE LISTED - ONLY THE MOST COMMON
CODE DESCRIPTION CODE DESCRIPTION CODE DESCRIPTION
B Sp. “H” Dimension G No Rod Threads L 303 Stainless Steel Rod
C Sp. “J” Dimension GB No Rod Threads Both Ends LF Low Friction Cylinder
CB Sp. “H” & “J” Dimensions GF No Rod Threads Front End M Hollow Rod
CH Sp. “H” & “J” For Cyl-Check GR No Rod Threads Rear End NT NoTang
CS Sp. Per Customers Specs. H Sp. Per Customers Drawing Q Stainless Steel Snap Ring
D Sp. “CC” Dimension HTP Hi-Temp. Packings RB Bleeder Valve Both Ends
DRP Double Rod Packing IB “AB” Pin Both Ends RF Bleeder Valve Front End
EPF Extra port in Front IF “AB” Pin Front End RM Magnet On Piston
EPR Extra port in Rear IR “AB” Pin Rear End RR Bleeder Valve Rear End
EPB Extra port Both Ends J Special Tail RG Outboard Rod Guide
F Non-standard Port Location K Female Thread In Rod U Steel Tube
FS Fail Safe W/Spring In Front KR Sp. “H” & “J” For K & KR Kits W Stronger Spring
WR Rod Wiper
MATERIALS: Special seal compounds are available for a wide range of fluid media
and environments. Tubes, Heads, Pistons and Rods can be supplied plated, hardcoated or in other materials.
Please consult the factory for special requirements, stating quantity required.
SPECIAL DESIGNS: Many times Allenair is able to change the standard configuration of our Cylinders to meet
Customer’s special requirements. A print from the Customer is needed so we can evaluate and properly quote such
specials. Internal Non-Rotating Rod Cylinders can be made in 2”, 3” and 4” bore sizes with maximum stroke of 20”.
16 PLEASE CONSULT FACTORY ON THE ABOVE SPECIALS STATING QUANTITIES REQUIRED.
CYLINDERS
• DIMENSIONS
TYPES A, C & E SINGLE ENDED

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

M + S T R OK E ( DOU B L E ACT ING)
M + ( S T R OK E X 2 ) ( S INGL E ACT ING)

E A + S T R OK E ( DOU B L E ACT ING) D

F A + ( S T R OK E X 2 ) ( S INGL E ACT ING)
B B J/2
C N AA N.P .T . N H
J

P IS T ON F U L L Y R E TR A CT E D

CC
Z BB
G BB O DIA.
O DIA.
TYPES AD, CD & ED DOUBLE ENDED
A + S T R OK E ( DOU B L E ACT ING)
A + ( S T R OK E X 2 ) ( S INGL E ACT ING)
D D
B B
AA N.P .T . C
H + S T R OK E N N
H
J J
P IS T ON R E T R A CT E D T O E X T R E ME L E F T

CC CC
BB BB
O DIA. O DIA.

A B C D E F G H J M N O Z
CYL. BORE
TYPE TYPE OS TYPE A TYPE C & E Std OS
SIZES Std
A C&E (Front Only) Std OS Std OS (Front only)

7/8” 2-1/16” 3-1/16” 3/8” 1-1/8” 5/8” X 1” 11/16” 3/8” 1” 7/8” 3-15/16” X 4-15/16” X 1/8” 3/4” X 1/4”
1-1/8” 2-1/16” 3-1/16” 3/8” 1-3/8” 5/8” 5/8” 1” 11/16” 3/8” 1”** 7/8”** 3-15/16” 4-1/8” 4-15/16” 5-1/8” 1/8” 3/4*** 7/8” 1/4”
1-1/2” 2-5/8” 3-5/8” 1/2” 1-3/4” 7/8” 7/8” 1-1/4” 7/8” 1/2” 1-7/16” 1-1/4” 5-3/16” 5-3/16” 6-3/16” 6-3/16” 3/16” 1-1/16” 1-1/16” 5/16”
2” 2-5/8” 3-5/8” 1/2” 2-1/4” 7/8” 7/8” 1-1/4” 7/8” 1/2” 1-7/16” 1-1/4” 5-3/16” 5-3/16” 6-3/16” 6-3/16” 3/16” 1-1/16” 1-3/8” 5/16”
2-1/2” 2-7/8” 3-7/8” 9/16” 2-3/4” 1” 1” 2” 1-3/8” 5/8” 1-11/16” 1-1/2” 6-3/16” 6-3/16” 7-3/16” 7-3/16” 1/4” 1-3/8” 1-1/2” 7/16”
3” 2-7/8” 3-7/8” 9/16” 3-1/4” 1” 1” 2” 1-3/8” 5/8” 1-11/16” 1-1/2” 6-3/16” 6-3/16” 7-3/16” 7-3/16” 1/4” 1-3/8” 1-1/2” 7/16”

4” *4-7/8” *4-7/8” 13/16” 4-3/8” 1-1/8” 1-7/8” 2-3/16” 1-7/16” 3/4” 2-1/4” 1-7/8” 9-1/4” 10” 9-1/4” 10” 3/16” 1-3/4” 2-1/4” 1/2”

CYL. BORE BB CC ROD DIA. STANDARD WRENCH FLATS

AA
SIZES Std OS (Front Only) Std OS Std OS
ROD DIA. W X Y
7/8” 1/8 3/4”-16 X 3/8”-16 X 3/8” X X
3/8” 5/16 15/16 5/16 Y
1-1/8” 1/8 3/4”-16*** 7/8”-14 3/8”-16 1/2”-13 3/8” 1/2”
1/2” 7/16 1-3/8 5/16
1-1/2” 1/4 1”-14 1”-14 1/2”-13 5/8”-11 1/2” 5/8”
5/8” 1/2 1-3/8 5/16
2” 1/4 1”-14 1-3/8”-12 5/8”-11 3/4”-10 5/8” 3/4” W
3/4” 5/8 1-5/8 5/16
2-1/2” 3/8 1-3/8”-12 1-1/2”-12 3/4”-10 1”-14 3/4” 1”
1” 7/8 2-1/8 3/8
3” 3/8 1-3/8”-12 1-1/2”-12 3/4”-10 1”-14 3/4” 1”
1-1/4” 1-1/8 2-1/8 3/8
4” 1/2 1-3/4”-12 2-1/4”-12 1”-14 1-1/4”-12 1” 1-1/4”
*5-3/8” on Single Ended Cylinders having Tang section, except types AN, CN & EN.
**On Oversize Models, H=1-3/8” & J=1-1/4”
***3/4”-16 Both ends on Types “A” & “E”
3/4”-16 Rear and 7/8”-14 Front on Type “C”. Omit dimension E when laying out Cylinder with Tang section omitted.
N dimension remains except on 7/8”, 1-1/8” and 4” bores. 17
 CYLINDERS
• DIMENSIONS
TYPES AN, CN & EN INTEGRAL REAR SWIVEL
DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

M + S T R OK E ( DOU B L E ACT ING)

M + ( S T R OK E X 2 ) ( S INGL E ACT ING)

E A + S T R OK E ( DOU B L E ACT ING) D

C A + ( S T R OK E X 2 ) ( S INGL E ACT ING)
B B J/2
P AA N.P .T .
F N H
J

P IS T ON F U L L Y R E T R A CT E D
K L V
V1

CC
BB
Z -DIA. O-DIA.

H M CC
CYL.
BORE E F TYPE TYPE K L TYPE AN TYPES CN & EN P V V1 Z
SIZES STD OS
AN CN & EN Std OS Std OS

7/8” 13/16” 7/16” 1” 1” 7/8” 1/4” 3-11/16” X 4-11/16” X 7/8” 13/16” 7/16” 1/4” 3/8”-16 X
1-1/8” 1” 11/16” 1”** 1”** 15/16” 3/8” 3-15/16” 4-1/8” 4-15/16” 5-1/8” 1-1/8” 7/8” 9/16” 3/8” 3/8”-16 1/2”
1-1/2” 1-5/8” 15/16” 2-7/16” 1-7/16” 1-1/4” 1/2” 6-1/4” X 6-1/4” X 1-1/2” 1-1/2” 13/16” 3/8” 5/8”-11 X
2” 2-1/4” 1-9/16” 2-7/16” 1-7/16” 1-1/2” 1/2” 6-7/8” 6-7/8” 6-7/8” 6-7/8” 2” 1-7/8” 1-3/16” 1/2” 5/8”-11 3/4”-10
2-1/2” 1-13/16” 1-1/8” 3-11/16” 2-11/16” 1-1/2” 1/2” 7-15/16” 7-15/16” 7-15/16” 7-15/16” 2-1/4” 1-11/16” 1” 1/2” 3/4”-10 1”-14
3” 2-5/16” 1-5/8” 3-11/16” 2-11/16” 1-1/2” 1/2” 8-7/16” 8-7/16” 8-7/16” 8-7/16” 2-1/4” 1-3/4” 1-1/16” 1/2” 3/4”-10 1”-14
4” 3-3/8” 2-3/8” 2-1/4” 2-1/4” 2-1/4” 3/4” 9-11/16” 10-7/16” 9-11/16” 10-7/16” 3” 2-1/2” 1-1/2” 3/4” 1”-14 1-1/4”-12

FOR ALL DIMENSION NOT LISTED, SEE TABULATIONS ON PAGE 17

TYPES ABB, CBB & EBB BACK-TO-BACK
A + S T R OK E ( DOU B L E ACT ING) A + S T R OK E ( DOU B L E ACT ING)
A + ( S T R OK E X 2 ) A + ( S T R OK E X 2)
( S INGL E ACT ING) Y ( S INGL E ACT ING)
D D
B B B B
H N AA N.P .T . AA N.P .T . N H C DIA.
J J

P IS T ON F U L L Y R E T R A CT E D P IS T ON F U L L Y R E T R A CT E D

CC
CC BB
O-DIA. CYL. BORE SIZES Y
O-DIA.
BB
7/8” 1/2”
1-1/8” 1/2”

FOR ALL DIMENSION NOT LISTED, SEE TABULATIONS ON PAGE 17 1-1/2” 1/2”
2” 1/2”
2-1/2” 1/2”
3” 1/2”
18 4” 1-1/8”
CYLINDERS
• DIMENSIONS

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

TYPES AS, CS & ES SINGLE ENDED A + S T R OK E ( DOU B L E ACT ING)
A + ( S T R OK E X 2 ) ( S INGL E ACT ING)
D D
V B B
W AA N.P .T .
T T H
J

P IS T ON F U L L Y R E T R A CT E D
R C
S
CC

CYL. BORE SIZES R S T U V W

7/8” 1-1/32” 3/4” 11/32” 7/32” 1-1/2” 1-1/8”
1-1/8” 1-1/8” 3/4” 11/32” 7/32” 1-1/2” 1-1/8”
1-1/2” 1-17/32” 1” 1/2” 9/32” 2” 1-1/2”
2” 2” 1-1/4” 1/2” 11/32” 2-1/2” 1-5/8”
TYPES ASD, CSD & ESD DOUBLE ENDED
D D
U
H + S T R OK E AA N.P .T . T H

J J
P IS T ON F U L L Y
R E T R A CT E D T O
L E FT

FOR ALL DIMENSIONS NOT LISTED, SEE TABULATIONS ON PAGE 10.

TYPES AP, CP & EP TYPE ET
M + ( S T R OK E X 2 )
M + F IR S T S T R OK E + T OT AL S T R OK E E
E A + F IR S T S T R OK E A + T OT AL S T R OK E F A + S T R OK E A + S T R OK E D
F Y D B B B B J/2
B B B B J/2 AA N.P .T .
C N Y AA N.P .T . N
C AA N.P .T . H
N AA N.P .T . N H
J
J
P IS T ON F U L L Y R E T R A CT E D P IS T ON F U L L Y R E T R A CT E D
P IS T ON F U L L Y R E T R A CT E D P IS T ON F U L L Y R E T R A CT E D

CC
CC Z BB
� BB O-DIA.
BB O� DIA. G O-DIA.
G O� DIA. BB

TYPES APD, CPD & EPD TYPES ETD

B B B B
B B B B
J J
J J

Y Y
N N O DIA
N N
H+STROKE D A + FIRST STROKE Y A + TOTAL STROKE D H
H+STROKE D A + STROKE Y A + STROKE D H
AA N.P.T. AA N.P.T. C C
AA N.P.T. AA N.P.T.
X X
W W
CC
BB BB CC CC
BB
O DIA O DIA

M M
CYL. BORE CYL. BORE
TYPE AP TYPES CP & EP Y H Y
SIZES SIZES STD OS
STD OS STD OS
1-1/2” 8-9/16” 8-9/16” 10-9/16” 10-9/16” 3/4” 1-1/2” 2-1/16” 11-3/16” 11-3/16” 3/4”
2” 8-9/16” 8-9/16” 10-9/16” 10-9/16” 3/4” 2” 2-1/16” 11-3/16” 11-3/16” 3/4”
2-1/2” 10-3/16” 10-3/16” 12-3/16” 12-3/16” 1-1/8” 2-1/2” 1-11/16” 12-3/16” 12-3/16” 1-1/8”
3” 10-3/16” 10-3/16” 12-3/16” 12-3/16” 1-1/8” 3” 1-11/16” 12-3/16” 12-3/16” 1-1/8”
4” 15-1/4” 16” 15-1/4” 16” 1-1/8” 4” 2-1/4 15-1/4 16 1-1/8

FOR DIMENSIONS NOT LISTED, SEE TABULATIONS ON PAGE 17 19

 CYLINDERS
• MOUNTS

MOUNTING BRACKETS & DIMENSIONS

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

FOOT FLANGE ROD CLEVIS, MOUNTING NUTS

CYL. ROD NUT ONLY SWIVEL
NUT & PIN BLOCK
BORE OS” OS” BRACKET TRUNNION OS”
STD STD MOUNT STD
SIZES (Front Only) (Front Only) SPIN (Front Only)
STD OS STD OS
7/8” A-132 X A-129 X A-145 X A-126 X A-139 T-7/8 BM-7/8 A-114 A-114
1-1/8” A-132* A-132-OS A-129* A-129-OS A-145 A-1545 A-126 A-1526 A-139 T-1 BM-1 A-114 A-114-OS
1-1/2 A-232 A-232 A-229 A-229 A-1545 A-245 A-1526 A-226 A-239 T-1.5 BM-1-1/2 A-214 A-214
2” A-232 A-232-OS A-229 A-229-OS A-245 A-345 A-226 A-326 A-239 T-2 BM-2 A-214 A-314
2-1/2” A-332 A-332-OS A-329 A-329-OS A-345 A-445 A-326 A-426 A-339 T-2.5 X A-314 A-314-OS
3” A-332 A-332-OS A-329 A-329-OS A-345 A-445 A-326 A-426 A-339 T-3 X A-314 A-314-OS
4” A-432 A-432-OS A-429 A-429-OS A-445 A-445-OS A-426 A-526 A-439 T-4 X A-414 A-414-OS

*1-1/8” bore Type “C” Cylinders require OS Mount or Mounting Nut on front and standard on rear.
**AII Single Ended OS Cylinders take standard Mounts or Mounting Nuts on rear end.
MOUNTING NUTS A
PART NO. A B C
Mounting Nuts supplied only with A-114 3/4” - 16 1-1/16” 3/8”
Flange or Foot Mounts and are in- A-114-OS 7/8” -14 1-1/4” 25/64”
cluded in the price of those Mounts. A-214 1”-14 1-1/2” 1/2”
However, they may be purchased as a A-314 1-3/8”-12 1-3/4” 5/8”
separate item. B C A-314-OS 1-1/2” - 12 1-13/16” 5/8”
A-414 1-3/4” -12 2-1/4” 3/4”
A-414-OS 2-1/4-12 3” 1”

MOUNTING BRACKET DIMENSIONS

FOOT MOUNT F
PART NUMBERS

C DIM. A-132 A-232 A-332 A-432

B OS OS OS OS
STD STD STD STD

A 11/16” 11/16” 1-1/8” 1-1/8” 1-3/8” 1-3/8” 1-7/8” 1-7/8”

O DIA

A
B 7/8” 7/8” 7/8” 7/8” 1-1/4” 1-1/4” 1-3/4” 1-3/4”

E
C 1-3/8” 1-3/8” 1-9/32” 1-9/32” 1-29/32” 1-29/32” 2-17/32” 2-17/32”
S D
D 3/16” 3/16” 1/4” 1/4” 5/16” 5/16” 1/2” 1/2”
G E 9/32” 9/32” 9/32” 9/32” 13/32” 13/32” 15/32” 15/32”
F 1-11/16” 1-11/16” 1-5/8” 1-5/8” 2-1/4” 2-1/4” 3-1/4” 3-1/4”
NT OPTION SUGGESTED WHEN G 2-1/2” 2-1/2” 2-1/2” 2-1/2” 3-1/2” 3-1/2” 5” 5”
USING FRONT FOOT MOUNT ONLY 0 3/4” 7/8” 1-1/16” 1-3/8” 1-3/8” 1-1/2” 1-3/4” 2-1/4”
S 1-9/32” 1-9/32” 1-3/4” 1-3/4” 2-3/8” 2-3/8” 3-3/16” 3-3/16”

FLANGE MOUNT • NT Option suggested

Front or Rear • J2 Option suggested provides Tang flush with
C
flange mounting surface.
PART NUMBERS
C B
A-129 A-229 A-329 A-429
O DIA
DIM.
STD OS STD OS STD OS” STD” OS
D
A A 9/32” 9/32” 11/32” 11/32” 13/32” 13/32” 7/16” 1-29/32”
E E
B 9/32” 9/32” 9/32” 9/32” 13/32” 13/32” 15/32” 15/32”
C 2” 2” 2-1/2” 2-1/2” 3-3/8” 3-3/8” 4” 4”
D 5/8” 5/8” 7/8” 7/8” 1” 1” 1-1/8” 1-29/32”
E 2-1/2” 2-1/2” 3-1/4” 3-1/4” 4-1/2” 4-1/2” 5-1/4” 5-1/4”
0 3/4” 7/8” 1-1/16” 1-3/8” 1-3/8” 1-1/2” 1-3/4” 2-1/4”
20
CYLINDERS
• MOUNTS

DOUBLE ACTING & SPRING RETURN: 7/8” - 4” BORES

A H B F

THREAD SIZE (CC) D G

G
E

PART NUMBERS
DIM. A-145 A-1545 A-245 A-345 A-445
STD STD STD STD STD OS
A 1-3/4” 2-1/4” 2-1/4” 2-3/8” 3-3/8” 3-1/2”
B 1-3/8” 1-3/4” 1-3/4” 1-13/16” 2-5/8” 2-5/8”
CC 3/8” - 16 1/2”- 13 5/8” - 11 3/4” - 10 1” - 14 1-1/4” - 12
D 5/16” 3/8” 3/8” 1/2” 5/8” 3/4”
E 3/4” 13/16” 13/16” 3/4” 1-1/16” 1-1/8”
F 1/4” 5/16” 5/16” 7/16” 1/2” 3/4”
G 3/4” 1” 1” 1-1/4” 1-1/2” 1-3/4”
H 7/32” 5/16” 3/8” 27/64” 1/2” 23/32”

SWIVEL BRACKET & PIN PART NUMBERS

DIM
A A-139 A-239 A-339 A-439
A 1-3/4” 2-1/4” 3” 3-3/4”
B 2-1/4” 3” 4” 5”
A D
C 1/4” 5/16” 5/16” 1/2”
G Z
D 9/32” 9/32” 13/32” 15/32”
G 3/8” 1/2” 5/8” 3/4”
C
S S 1-9/32” 1-3/4” 2-3/8” 3-3/16”
Z 1/4” 5/16” 7/16” 1/2”
B B

BLOCK MOUNT S S
PART NUMBERS
DIM.
BM-7/8 BM-1-1/8 BM-1-1/2 BM-2
A 1-1/2” 1-3/4” 2-1/4” 3”
F B 1” 1” 1-1/4” 1-1/4”
C 1-1/8” 1-3/8” 1-3/4” 2-1/4”

A C E
D 9/32” 9/32” 9/32” 11/32”
D
E 1-5/8” 1-7/8” 2-3/8” 3”
NT OPTION SUGGESTED
B F 2-1/4” 21/2” 3” 3-3/4”
S 3/4” 7/8” 1-1/8” 1-3/8”

TRUNNION MOUNT A DIM. PART NUMBERS

1/16 1/16
T-7/8 T-1 T-1 .5 T-2 T-2.5 T-3 T-4
A 3-1/2” 3-1/2” 4” 4” 5-1/2” 5-3/4” 7”
B 2-1/4” 2-1/4” 3” 3” 4” 4-1/4” 5-1/2”
D DIA

C
C 1-1/8” 1-3/8” 1-3/4” 2-1/4” 2-3/4” 3-1/4” 4-3/8”

B G D 3/8” 3/8” 1/2” 1/2” 3/4” 3/4” 3/4”

E 3/4” 3/4” 1-1/4” 1-1/4” 1-1/2” 1-1/2” 1-1/2”
E F 7/8” 7/8” 1-1/8” 1-3/8” 1-7/8” 2-1/8” 2-11/16”
NT OPTION SUGGESTED E/2
G 2” 2” 2-5/8” 3-1/8” 4” 4-1/2” 5-3/4”
F

21