Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 28 views

    Dan

    Uploaded by

    cengiz kutukcu
    WAKEFIELD DAN

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd

    Dan

    Uploaded by

    cengiz kutukcu
    28 views5 pages
    WAKEFIELD DAN

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    WAKEFIELD DAN

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    28 views5 pages

    Dan

    Uploaded by

    cengiz kutukcu
    WAKEFIELD DAN

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    of 5
    . WAKEFIELD (Md WEAR-EDGE MILLING MACHINE @z, Type: DAN Page 2 of Supply 3 and Oltmist Lubricator 4 Preparations 5 [Assembly of Machine 5 Positioning of Miling Tip End 6 ‘Operations. 6 Important Note 6 ‘Spare Pars List 7 Tool List 5 (The above image is for 320-400mm bore) [WAKEFIELD CORPORATION ‘CALL: #81 (0)842-27-6627 137-28 Yamaha Ao, Kru FAK: 48140)942.27-8975 Fukuoka 69970842 Japan ‘mail: info@wakefield.co.jp tp: mwuw.wakefele.coip Specifications 0508mPs — 1 16, 600~30,000nin DaNs01e0 awsor@0 DaNs098 20 25 0 Maintenance: machine after use re no moisture re jist Lubricator (Optional Supply) © Oran Pug fe Sight Glass ® 1 Bow Remove Oil au @ and filo unt showing ful inthe O-Leve Sight lass. 2) Theol flows set bythe valve @). erease the flow and ant-lockwise to increase the Yow. a inthe system in do o monitor the ol fow in the sight glass @, 4) Main alr stop valve i ted or safety reasons ning of Milling Tip End: assembled machine ito the cylinder liner untl it rests and rolls trey on the roe sts of thatthe height ofthe miling tis the same asthe position where grooves fo be mile. Tu the ‘machine round the drcumference to check Fequired re-adust te height ana femiyre-Ughten lock grips an bots, ‘The machine s now ready for use, Operation: Important Note: “The miting shouldbe done from the side and extreme care should be made nat to alow the miling to be done more than 2 mm below the line, in case of wear edge removal not more than 2 mm below the TOC {or the top piston ing, else itmay cause bow byes. \When commencing the ming start from a sight higher positon and move down slowly atthe same lime increasing te feed sideways. ‘The feed is fed, and the depth ofthe wear edge Is Increased by releasing the motor shat knob ant- clockwise. ‘Startthe ai motor an turn feed. The machine should to the underside ofthe head pipe. the beginning ofthe ming pocedure in reumerence may be necessary to mave the assembly back and for order to remove tha edge quicker, and tally slowly around the Continue riling unt the edge is removed, plaase note thatthe machine wi fllaw the oval shape or roundness ofthe ner. Using the smaller miting tips wil ender a "Nese" shaped cut, recommended when removing the wear {edge and using the ips wil make a moon shaped cu for grooves. When ming grooves, t 's recommendable to cantact the engine maker in order to venly te roqlted shape and depth of grooves. Tool List No ane sKeToH ey | wean | Rewaris Hexagon wench ‘wai | -a5 Cres ‘Open-end Spanner | z 0.2 kgs | for grinding motor * =e ‘Storing Box 1 Bkgs 3 Travan Mane 2 4 7g

    You might also like