Mercedes-Benz DBL 8451

Company Standard Date published: 2015-06

Supersedes: DBL 8451:2014-12

Total no. of pages (including annexes): 16

Person in charge: Dr. Dieter Hesse
E-mail: dieter.hesse@daimler.com
Plant: 010; Dept.: TF/VWO
Date of translation: 2015-09 Phone: +49 (0) 711-17-23506

Electrodeposited Zinc and Zinc Alloy Coatings

for Components Manufactured from Ferrous Materials

Foreword

This supply specification describes the special requirements, properties, and characteristics of parts
with electrodeposited and aftertreated zinc and zinc alloy coatings.

Changes

In comparison with edition 2014-12, the following changes have been made:

• In Section 4, "Requirements": Note on the deletion of coatings containing Cr(VI) for commercial
vehicles, buses and vans included
• Annex A: Conversion table included and description of the procedure to enable the substitution
of coating systems containing Cr(VI) with Cr(VI)-free systems for commercial vehicle, bus and
van components (all EU vehicle categories except M1 and N1).
• With product versions .12 and .22, use of sealing permissible again
• Section 6.2: Requirements for the corrosion protection of internal surfaces of tubes
and sleeves revised
• Section 6.3 added

NOTE: This translation is for information purposes only.

The German version shall prevail above all others.

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 2

Contents

1 Scope ............................................................................................................................................... 3
2 Normative references ....................................................................................................................... 4
3 Terms and definitions ....................................................................................................................... 5
4 General requirements ....................................................................................................................... 6
4.1 General ............................................................................................................................................. 6
4.2 Basic materials ................................................................................................................................. 7
4.3 Material strength ............................................................................................................................... 7
4.3.1 Materials with strengths ≥1000 N/mm2 ............................................................................................. 7
4.3.1.1 Reduction of hydrogen absorption ................................................................................................... 7
4.3.1.2 Heat treatment .................................................................................................................................. 7
5 Abbreviated material designation for documentation ....................................................................... 8
6 Technical requirements and process descriptions ........................................................................... 8
6.1 Corrosion protection coatings ........................................................................................................... 8
6.1.1 Metallic base coats ........................................................................................................................... 9
6.1.1.1 Zinc coatings (Zn) ............................................................................................................................. 9
6.1.1.2 Zinc-nickel coatings (ZnNi) ............................................................................................................... 9
6.1.1.3 Zinc-iron coatings (ZnFe) ................................................................................................................. 9
6.1.2 Aftertreatment for protection of metallic coating ............................................................................... 9
6.1.2.1 Passivation ....................................................................................................................................... 9
6.1.2.2 Sealings ............................................................................................................................................ 9
6.1.2.3 Organic top coats ............................................................................................................................. 9
6.2 Coatability with tubes (pipes) and sleeves (exception) .................................................................. 10
6.3 Coatability of special component geometries (possible exceptions).............................................. 10
7 Tests ............................................................................................................................................... 10
7.1 Corrosion resistance test ................................................................................................................ 10
7.1.1 Corrosion test in accordance with DIN EN ISO 9227 NSS (salt spray test) .................................. 11
7.1.2 Corrosion test in accordance with DIN EN ISO 6270-2 CH (constant condensation water test) .. 11
7.1.3 Corrosion test in accordance with DIN 50018 AHT 2,0S (Kesternich test) .................................... 11
7.1.4 Corrosion protection requirements for parts with reshaping after coating ..................................... 11
7.2 Coating adhesion test (thermal shock resistance, blistering) ......................................................... 12
7.3 Test for susceptibility to brittle fracture ........................................................................................... 12
8 Sample/test report .......................................................................................................................... 12
9 Deliveries ........................................................................................................................................ 12
Table 3: Technical data and requirements .................................................................................................. 13
Annex A (normative) Comparison table for substitution of Cr(VI) coatings with Cr(VI)-free coatings......... 14

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 3

1 Scope

This DBL applies to parts with electrodeposited zinc and zinc alloy coatings and subsequent aftertreatment.

This DBL does not apply to parts, with electrodeposited coating of individual components, that are applied
to raw bodies and subjected to pre-treatment and the painting process along with the body. It also does
not apply to parts with electrodeposited pre-coating that are then provided a top coat with the body.
The requirements for these applications are described in DBL 8466. For screws and nuts, refer to
DBL 9440, 9441, and 9460.

For the selection of suitable product versions of this DBL for vehicle components and to decide whether
the surface treatment conforms to the current corrosion protection guidelines, the unit responsible for
the component shall include the specialist colleagues from the Vehicle Concepts Corrosion Protection
department.
Approval for usage, following testing, shall be decided by each responsible component manager,
taking all the aspects that affect the component's function and durability into account.

Table 1: Product versions (PV), overview

Coating Zinc Zinc/Iron Zinc/Nickel

Parts category without with without with without with

thread thread thread thread thread thread
Surface

transparent, sealing allowed

when function not impaired
.15 .16 .96 .66 .76

transparent, not sealed .62 .72

transparent, sealed .86 .65
silver-colored .12 .22
black, sealed .13
black, additionally
with organic top coat
.19 .29 .69 .79

For requirements for the product versions above as well as the corresponding tests, refer to Section 7
and Table 3.

Blocking note:

With this edition of the DBL, PV .13 is reactivated for special applications as a Cr(VI)-free product version.

When PV.13 is used, black coloration results in a significantly lower corrosion resistance than versions
provided with an additional black organic top coat. PV .13 shall therefore only be used for interior vehicle
parts and only when a top coat must not be applied for technical or functional reasons and a black surface
must be used. Electrodeposited zinc or zinc-iron coatings serve as a base coat. This DBL product version
also applies to older parts for which surface protection according to DBL 8451.13 was specified on the
drawing.

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 4

2 Normative references

The following referenced documents are indispensable for the application of this supply specification.
For dated references, only the edition cited applies. For undated references, the latest edition of the
referenced document (including any changes) applies.

DBL 6714 Negative List - Constituents of Process Materials

General Requirements – Environmental Protection, Hazardous Substances,
DBL 8585
Dangerous Goods – Negative Substance List for the Selection of Materials
DBL 8440 Parts Manufactured from Ferrous Materials with Inorganic Coating
(Zinc Flake Coatings)
DBL 8466 Supply Specification Galvanic Zinc Coating of Individual Components
for the Body-in-White
DBL 9410 Supply Specification – Testing of Coefficients of Friction of Threaded Parts

DBL 9460 Fasteners with Thread and Micro-Encapsulated Liquid Adhesive

DBL 9440 Supply Specification – Fasteners with Metric Thread; Surface Protection
and Supplementary Technical Delivery Conditions
DBL 9441 Supply Specification – Surface Protection for Fasteners for Direct Screw
Connection in Metal Sheets and Plastic (Non-Metric Threads)
DIN 50018 Testing in a Saturated Atmosphere in the Presence of Sulfur Dioxide
DIN 50969-1 Prevention of Hydrogen-Induced Brittle Fracture of High-Strength Steel
Building Elements – Part 1: Advice on the Prevention
DIN 50969-2 Prevention of Hydrogen-Induced Brittle Fracture of High-Strength Steel
Building Elements – Part 2: Test Methods
DIN 50979 Metallic coatings - Electroplated coatings of zinc and zinc alloys on iron
or steel with supplementary Cr(VI)-free treatment
DIN EN 15205:2007-02 Determination of Hexavalent Chromium in Corrosion Protection Layers –
Qualitative Analysis
DIN EN ISO 2081 Electroplated coatings of zinc with supplementary treatments on iron or steel
DIN EN ISO 6270-2 Paints and Varnishes - Determination of Resistance to Humidity
Part 2: Procedure for Exposing Test Specimens in Condensation-Water
Atmospheres
DIN EN ISO 9227 Corrosion Tests in Artificial Atmospheres - Salt Spray Tests
VDA 235-204:2009-11 High-Strength Fasteners for the Automotive Industry
MBN 10513 Parts Manufactured from Ferrous Materials with Inorganic Coating
and Black Surface Finish - Assessment of Corrosion Onset

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 5

3 Terms and definitions

PV: Product version according to this DBL, e.g. DBL 8451.76

Zinc coatings (Zn):

Zinc coatings in accordance with this DBL are electrodeposited on ferrous materials
from aqueous electroplating baths.

Zinc-iron coatings (ZnFe):

Zinc-iron coatings are electrodeposited from an alkaline electrolyte with an iron installation rate
of 0,3 % to 1 % onto a metallic workpiece.

Zinc-nickel coatings (ZnNi):

The most popular electrodeposited zinc-nickel coatings have a nickel content of 12 to 16 %.
The significantly higher corrosion resistance of the metallic coating in combination with the
less prominent/voluminous corrosion products, compared to pure zinc coatings and low-alloyed
zinc-iron coatings, is characteristic of zinc-nickel coatings. This is also the reason for the
comparably higher temperature resistance of the passivated zinc-nickel coating.

Passivation:
Passivation is the creation of conversion coatings on newly deposited zinc or zinc alloy layers
by treatment with suitable Cr(VI)-free solutions. By doing so the newly electrodeposited coating
reacts with the passivation solution to form a thin film (approx. 0,05 µm to approx. 0,5 µm)
composed of complex reaction products, which covers the metallic coating. The formation
of the passivated coating may also result in iridescent effects on the component surface.

Sealing:
Sealing as defined by this DBL is the creation of a thin organic or inorganic protective coating
with a thickness of approx. 0,5-2 µm on zinc or zinc alloy coatings. The sealing is normally
applied on passivated surfaces, whereby the sealing penetrates into the passivation layer,
forming a composite coating. Depending on the sealing agent, the sealing shall be executed
wet on wet or following intermediate drying. The sealing agent may be provided with pigments
for coloration (black).

Top coats:
A top coat as defined by this DBL is a black organic or inorganic protective layer for zinc
or zinc alloy coatings with a layer thickness >2 µm. Top coats may contain suitable additives
for the adjustment of defined coefficients of friction.

Classification of corrosion resistance (Kb):

Kb I Transportation and storage protection, installation in oil gallery
Kb II Very low corrosion resistance, installation in non-corrosive
areas, e.g. in the vehicle interior
Kb III Low corrosion resistance, for parts that can change in appearance
due to corrosion
Kb IV Medium corrosion resistance, for parts in areas subject to a low level of corrosion
Kb V High corrosion resistance, for parts in visible area or where corrosion must be
excluded for functional reasons
Kb Vl Extremely high corrosion resistance

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 6

4 General requirements

4.1 General
To guarantee product safety and product quality, and to meet homologation requirements, all relevant
statutory regulations, guidelines and laws shall be complied with. In addition, the relevant requirements
of the Daimler Group apply.

All materials, procedures, processes, components, and systems shall conform to the current statutory
requirements regarding regulated substances and recyclability.

DBL 8585 and DBL 6714 shall be observed.

According to EU directive 2000/53/EC on end-of-life vehicles and the German law governing end-of-life
vehicles, it shall be ensured that corrosion protective coatings on components of vehicles of categories
M1 (passenger cars with a maximum of 8 seats) or N1 (commercial vehicles with a permissible gross
weight of up to 3,5 t - as per Annex II Section A of directive 70/156/EEC) which are brought onto the
market after 1 July 2007 do not contain any hexavalent chromium (Cr(VI)). Accordingly, this DBL
exclusively contains product versions with Cr(VI)-free coatings for corrosion control. On the other hand,
coating systems containing Cr(VI) may still be used in the case of commercial vehicles, buses, and vans
(all vehicle categories except M1 and N1).

Due to the specifications of the current EU chemicals directive (REACH), when using chromic acid
the production of corrosion protective coatings with conversion layers containing Cr(VI) on galvanically
produced zinc and zinc alloy coatings will be discontinued in European electroplating operations not later
than September 2017. As a result, the coating systems produced in the EU zone and specified on a high
number of commercial vehicle component drawings will no longer be available for commercial vehicles,
buses, or vans either.

To avoid modifying individual design drawings for the large number of components wherever possible,
Annex A specifies a conversion table and describes the procedure to enable the substitution of coating
systems containing Cr(VI) with Cr(VI)-free systems for commercial vehicles, buses, and van components
(all vehicle categories except M1 and N1).

As of 1.7.2017, all components previously designed according to this DBL with Cr(VI)-based chromating
shall be supplied with Cr(VI)-free passivation as per the substitution product versions in this DBL.
The relevant sampling process shall also be completed by then.

The supplier shall supply evidence of freedom from Cr(VI) based on recognized analytical methods
as per DIN EN 15205:2007-02.

The manufacturer shall take into account that depending on the geometry and dimensions of the
components, the corrosion resistance may be reduced as a result of handling, packaging, transportation
and feeding equipment.

The corrosion resistance values specified in this DBL shall be attained on delivery to the relevant
Mercedes-Benz plants.

Before applying this DBL for threaded parts, threading examinations and approvals by the responsible
fastener representative are recommended.

Sampling based on earlier editions of DBL 8451 required compliance with the coefficients of friction
as specified in DBL 9410 for threaded parts.

For new sampling of threaded parts according to this edition of DBL 8451, it shall always be ensured that
the coefficients of friction of the supplied threaded parts enable proper threaded connections (screw
technology properties generally based on DBL 9440). The required coefficient of friction window shall
be defined as necessary and during new sampling and for series deliveries. Deviations from the coefficient
of friction window as defined in DBL 9440 shall be indicated by the supplier. DBL 8451:2008-09 shall
apply to existing parts.

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 7

4.2 Basic materials

The parts to be electroplated shall not exhibit any material, machining or surface defects which could
impair the corrosion protection and/or the appearance of the coatings. This includes, for example, cracks,
pore clusters, foreign matter inclusions and laminations, sunk spots and cold welds, shrinkage and
toe-cracks, as well as swirls and shrink holes. If necessary, an agreement concerning surface quality
may have to be made.
Any contamination on the surface of the parts to be treated (corrosion products or scale, oil, grease,
dirt etc.) shall be completely removable during normal use of the automatic cleaning and pretreatment
facilities without leaving any residue.

4.3 Material strength

Production, joining and surface-treatment methods shall be executed such that any damage through
delayed, hydrogen-induced brittle fracture can be ruled out with a high degree of certainty.

4.3.1 Materials with strengths ≥1000 N/mm2

When coating components with strengths ≥1000 N/mm2 (possibly also locally restricted, e.g. for
case-hardened or cold-formed structures or in weld seam areas) safety from delayed brittle fracture
(hydrogen embrittlement) shall take particular precedence. The coater shall be notified if material
strengths are ≥1000 N/mm2. This also applies if the component strength exceeds this value in
some areas only.

The measures and tests required to eliminate the risk of hydrogen embrittlement, such as minimization
of component stresses, selection, composition and checking of chemicals, physical and chemical process
limits, types of tests, test frequency, number of test pieces etc., shall be documented in process and
inspection plans according to the state of the art. The treatment of incorrect coatings (removal of coatings
and new coatings) shall be investigated and the resulting consequences specified. The investigations shall
be documented.

For parts with threads and tensile strengths Rm ≥ 1200 N/mm2 or core and surface hardnesses > 385 HV,
coatings according to this DBL are not permissible (as per VDA 235-204:2009-11). In general, this also
applies to unthreaded parts.

Note:
Unthreaded parts with strengths ≥ 1200 N/mm2 that were coated according to DBL 8451 prior to
publication of DBL edition 2014-12 may continue to be used. The measures defined below for the
reduction of hydrogen absorption shall be observed in addition to the requirements for heat treatments
for hydrogen effusion. For new designs and particularly critical parts, a switch shall be made to DBL 8440
with acid-free pre-treatment.
4.3.1.1 Reduction of hydrogen absorption
The instructions contained in DIN 50969 Part 1 and Part 2 shall be observed. In addition to this,
the coater is expected to assess the process in detail (FMEA) with regard to all sub-steps in which
hydrogen can infiltrate the material structure. If necessary, the processes shall be optimized.
Process assessment shall be validated by component tests. Measures shall be derived from this
which serve to reliably minimize the amount of hydrogen infiltration into the material during the treatment,
and which enable a regular periodic examination of the effectiveness of such measures.
4.3.1.2 Heat treatment
Heat treatments are required to avoid brittle fractures; they shall be performed for hydrogen effusion after
electrodeposition and, if necessary to reduce component internal stress, also before electrodeposition.
Also refer to DIN 50969 Part 1.
The ideal heat treatment to be used for a part (temperature, duration, process sequence) shall be
ascertained and stated in the ISIR (initial sample inspection report). For general reference values, refer to,
for example, DIN 50979 and DIN EN ISO 2081. Care shall be taken to ensure that the properties of the
parts are not impaired in this process and evidence shall be provided of the efficacy of the heat treatment.

When coating components that are potentially subject to hydrogen embrittlement, it is also expected that,
in addition to the measures described above, additional distortion tests are performed to document reliable
non-critical process control (e.g. on finished electrodeposited components in a deformed fixture in which
the component is subjected to loads near the yield strength).

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 8

5 Abbreviated material designation for documentation

Example: Surface protection DBL 8451.62 (in the drawing block for surface protection)

6 Technical requirements and process descriptions

Following electroplating, parts shall be within the specified tolerances stated on the standard sheets
or drawings, taking any thread dimensions into special consideration.

6.1 Corrosion protection coatings

Parts shall exhibit a dense, uniform, homogeneous, (dull) glossy coating which bonds well with the
base material even under changing service temperatures and which does not chip off as a result
of the customary application and mounting torsion in use. A uniform appearance of the surface
shall also be provided in the passivated and, where applicable, sealed condition.
Damage to the coating through improper handling of the parts after electroplating, e.g. throwing
or unsuitable transportation conditions, shall be avoided.

The parts supplier or component manufacturer shall select the coater. Before initial sample coating,
a coordination process between the component manufacturer and coater should be performed in
which the optimal coating production process for the product is jointly defined.
Before commencement of production deliveries, the coating company shall determine and record
the complete pretreatment and coating process, the physical data (treatment periods, temperatures)
and the composition of all process chemicals, and, if required, optimize them. Individual process
intervention limits as well as the frequency of monitoring and analysis procedures shall be defined.
The resulting measures shall be specified by the coating company.
The documentation for this process description shall be submitted to Daimler AG when requested
during audits. The data shall be treated as confidential and not disclosed to third parties.

Any changes to the production coating process which according to the state of the art can influence
the properties of the base material or the coating shall be reported to Daimler AG promptly and
without prior request. A renewed sampling of the parts shall be performed.

In contrast to national and international standards, these Supply Specifications do not differentiate
between the manufacturing process for barrel or rack coating, because often when determining the
surface protection required, the process technology to be used is not yet known. Normally, the size
of the component and its design, along with the technology available at the coater's, will determine
whether the coating process should be performed using the less expensive barrel plating method
or by rack plating.
Should it be necessary to apply limitations to the coating process from the point of view of the
developer responsible for the component (BTV), e.g. for parts with thread that have to be produced
on the rack, this shall be noted on the drawing accordingly.

For coating in accordance with this DBL, a coat thickness less than 8 µm is not recommended.

The thickness of top coats is typically between 4 µm and 8 µm. This information serves orientation
purposes. The coat thickness may deviate, however, due to the geometry, for example.

Compliance with the corrosion requirements and required component tolerances is of primary importance.
The applied maximum coat thicknesses shall not cause impairments to the component or system function.

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 9

6.1.1 Metallic base coats

6.1.1.1 Zinc coatings (Zn)

Zn coatings offer the lowest corrosion protection quality within the systems of this DBL. With good
cathodic protection, relatively voluminous corrosion products occur on corrosive attack.

6.1.1.2 Zinc-nickel coatings (ZnNi)

Zinc-nickel coatings demonstrate the best behavior of the metallic coatings within this DBL with regard
to corrosion protection quality. The method used (electrolyte type) and the nickel content (specified and
actual values) in the layer shall be indicated in the initial sample inspection report (ISIR).

6.1.1.3 Zinc-iron coatings (ZnFe)

The method used and the content of the alloy element(s) (specified and actual values) in the layer shall
be stated in the initial sample inspection report (ISIR).

6.1.2 Aftertreatment for protection of metallic coating

Aftertreatment shall completely cover the electroplating, bond well and, apart from interference colors,
be uniform and free of spots.
6.1.2.1 Passivation
Generally, the electrodeposited metal coats are subjected to passivation treatments (conversion layers)
that result in a certain degree of corrosion protection of the metallic coating and prevent the surface
appearance from changing prematurely.

6.1.2.2 Sealings
For all PVs for which sealings are required or permissible, the following applies if the function is not
impaired:
Sealings serve to increase corrosion resistance and are generally permissible if the coat thickness is
not increased by more than 0,5 to 2 µm and if the functional properties of the component such as
transition resistance, weldability, compatibility with operating fluids or bonded connections are not
impaired.
Products that can be removed using cold cleaning solvent, e.g. oil-, grease-, or wax-based, are not
permitted for sealing.

For components which are glued and/or pressed in (e.g. core hole covers), particular attention shall
be given to the influence of the layer structure and/or sealant on the assembly and functional properties.
The use of specially specified products may become necessary in this respect. The use of sealants with
integrated lubricants which may have an effect on the sliding properties of the finish is not permitted in
principle with regard to these components. Any deviations shall be agreed and documented separately.

Parts that subsequently undergo electrophoretic dip coating shall not be sealed thereafter. The coater
shall be notified of this.
If an improvement of the coating corrosion resistance of passivated surfaces is also required for thermal
loads, this can be achieved by means of sealing. Suitable sealing means shall be defined after testing
and the exclusive application of these products ensured.

6.1.2.3 Organic top coats

PVs .19, .29, .69, and .79 apply to electrodeposited zinc and zinc alloy coatings on ferrous materials
that also have a thin organic top coat. The coatings serve as corrosion protection under maximum
demands and give the material a black color.
The applicability of these types of coating systems shall be ascertained and evidence provided in each
case by means of suitable investigations.
The processes and products used shall be recorded in the initial sample inspection report at the time
of initial sampling.

Organic top coats are generally not suitable for parts with a metric thread <M6 for dimensional reasons.

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 10

6.2 Coatability with tubes (pipes) and sleeves (exception)

This section does not apply to all components with internal surface areas, such as rivets, but exclusively
to tubes/pipes and sleeves (short tubing sections). Here, electrodepositing is hampered or prevented
by the shielding effect. For this reason, the internal surfaces of tubes, for example, are not coated, and
the coating at the ends of the tube "strays" only slightly into the inside of the tube depending on its inside
diameter. The greater the diameter/length ratio of the tubing, the better the coatability of the inside.
All requirements as per Section 7 and Table 3 are imposed on the external surface areas and also the
end edges (as for all other parts according to this DBL). The diameter/length ratio as of which the internal
surface areas shall also meet the requirements of this DBL is defined for tubes and sleeves in Table 2
in the following.

Table 2: Requirements for internal surfaces of tubes and sleeves

Inside diameter
Ratio =
Length or depth

Tubes, sleeves

All requirements also apply to the internal surface areas. ≥1

No requirements are imposed on the internal surface areas

with regard to behavior in the Kesternich test; the ≥0,5 and <1
requirements of the salt spray test in ISO 9227 shall be met.
No corrosion protection requirements as per Table 3
are imposed on the internal surface areas whatsoever. <0,5
Corrosion protection arising in these areas due to the
process shall be accepted.

If requirements beyond those listed in the table above are imposed on internal surface areas of tubes
and sleeves, additional measures such as internal anodes during coating shall be agreed.
For tubes with reduced corrosion resistance of the "internal surfaces" and highly active internal surfaces
due to the galvanic treatment process, the component supplier shall ensure that these areas are provided
with adequate transportation and storage protection so that corrosion-free delivery to the Mercedes-Benz
plants is ensured. In the case of sealing and also any temporary corrosion protection substances which
are used, and particularly in the case of internal tube surfaces, attention shall be paid to possible residue
formation, meeting of residual contamination requirements, and compatibility with service products.

6.3 Coatability of special component geometries (possible exceptions)

If, in addition to the exceptions described in Section 6.2, adequate coating on all sides through the
application of standard galvanic processes in barrel or rack coating is not feasible due to special
component geometries, the application of special measures such as internal anodes shall be decided
on in coordination with Daimler AG. The agreed special measures shall be documented.

7 Tests

7.1 Corrosion resistance test

The corrosion resistance test is deemed to have been passed when the following requirements, as well
as those in Table 3 of this DBL, have been complied with.

All parts shall be degreased prior to the corrosion test in petroleum benzine, ultrapure, DAB, boiling range
40 – 60 °C.

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 11

7.1.1 Corrosion test in accordance with DIN EN ISO 9227 NSS (salt spray test)
The requirements labeled with "A)" in Table 3 shall be met with and without heat treatment before
corrosion exposure in accordance with DIN EN ISO 9227 NSS.

Following the required test period as per DIN EN ISO 9227 NSS, remove the components from the
test cabinet, rinse with demineralized water and then dry before the assessment, e.g. by gently blowing
off with compressed air. The anti-corrosion coatings shall not demonstrate any blisters or peeling during
the specified corrosion tests after the specified test period.

Assessment of black parts for freedom from zinc corrosion:

Test instructions MBN 10513, with corrosion level KG 1, indicate how the onset of zinc corrosion appears
on barrel parts.

Note: The specified corrosion test in accordance with DIN EN ISO 9227 NSS is only a "short-term test
method" used to prove that the supplied coating quality conforms with the defined target specification.
The test results of the salt spray test, however, cannot be used to derive any conclusions concerning
the suitability of the coated component under corrosion conditions in practice.

7.1.2 Corrosion test in accordance with DIN EN ISO 6270-2 CH

(constant condensation water test)
During initial sampling of surfaces, as well as during requalification tests for PVs .19, .29, .69, and .79,
evidence shall be provided that neither base material or coating corrosion, nor blistering or peeling
occur (system test/validation) under constant condensation water exposure for 240 h in accordance with
DIN EN ISO 6270-2 CH. If this is the case, further series condensation water tests need not be performed.

7.1.3 Corrosion test in accordance with DIN 50018 AHT 2,0S (Kesternich test)
The designation of the testing climates has changed with the issuing of DIN 50018:2013-05. The former
designation DIN 50018 KFW 2,0S was renamed to DIN 50018 AHT 2,0S.

7.1.4 Corrosion protection requirements for parts with reshaping after coating
Reshaping after surface treatment may impair corrosion resistance. Coating corrosion (zinc corrosion)
is not generally assessed in the area of the component surface reshaped after coating. The requirements
for the base material (Fe) corrosion protection also apply to these areas, however. Deviations from this
rule shall be stated on the component drawing. The initial sample inspection report shall point out the
presence of components which have been reshaped after coating.

For surface areas that are not affected by reshaping, as well as the complete components before
reshaping, the normal requirements for the respective PV shall apply as per Table 3. The results
of the testing of components before reshaping shall also be added to the initial sample inspection
report for this reason.

Example:
Corrosion protection requirements for and assessment of reshaped tubing according to DBL 8451.62

1. The following are required for the entire straight, coated tubing before reshaping
and for straight tubing sections after reshaping:

a. 240 h without Zn corrosion in the test according to DIN EN ISO 9227 NSS
b. 720 h without Fe corrosion in the test according to DIN EN ISO 9227 NSS
c. 2 cycles without Fe corrosion in the Kesternich test according to DIN 50018 AHT 2,0S

2. The following requirements are placed on tubing after reshaping in the reshaped tubing
sections:

720 h without Fe corrosion in the test according to DIN EN ISO 9227 NSS

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

 DBL 8451:2015-06 page 12

The requirements shall apply for this example with and without previous heat treatment

Definition of the straight tubing sections for tubing reshaped after coating:

Tubing sections shall be considered to be straight if they are longer than 10 cm on the reshaped tubing.
During assessment based on the criteria above, the starting lengths of the straight section shall not be
assessed. The unassessed length shall measure 3 cm in each case. Example: The straight length of
the reshaped area of subsequently bent tubing is 12 cm. Of this, 3 cm on each end is not assessed.
This results in an average straight tubing length for assessment of 6 cm.

7.2 Coating adhesion test (thermal shock resistance, blistering)

Store test specimens for 30 minutes at 220 ± 10 °C and quench them immediately afterwards in water
at a temperature of 15 °C to 25 °C. No chipping or blistering of the coat shall occur. Bending of the
components is recommended as an additional adhesion test, as far as practicable.

7.3 Test for susceptibility to brittle fracture

For parts with strength ≥1000 N/mm2, evidence shall be provided by means of suitable distortion tests
in accordance with DIN 50969 Part 2 that the complete process has been carried out successfully.

8 Sample/test report
The following information regarding this DBL shall be indicated in the initial sample inspection report:

• Specified DBL PV
• Any agreed deviations from the DBL requirements
• Coater applying surface protection, or subcontractor if applicable
• Coating methods employed and materials applied, including product names
• If the component was reshaped after coating, additional information as per Section 7.1.4
• Information concerning any measures performed to prevent hydrogen embrittlement
• Test results: the appearance of the test specimens after the test, along with the position
of the test specimens in the tester, shall be documented. The pictures shall be enclosed
with the initial sample inspection report.
• Name of the testing body (supplier and/or subcontractor and/or testing institute)

In the case of several coaters/locations, each electroplating shop shall submit initial samples with the ISIR,
and particular attention shall be paid to identical functional and/or assembly characteristics of the parts
that are finish-plated in different systems. This normally also requires the use of identical products
(base chemicals) for the creation of the layer.
The data shall be treated as confidential and not disclosed to third parties.

9 Deliveries
Ongoing deliveries shall correspond to the approved samples.
In the event of any changes regarding the coater, location, process, significant parts of the process,
or the layer-forming products, renewed initial sampling of the surface quality shall be performed.
For production deliveries, the supplier shall conduct an in-process quality inspection and make
the data available on request.

All parts shall be delivered free from corrosion products. When storing parts until they are required
for subsequent processing or assembly, preservation or special storage conditions may be required.

Copyright Daimler AG

Uncontrolled copy when printed : Witold Rybak, 2016-04-27

Uncontrolled copy when printed

DBL 8451:2015-06 page 13

Table 3: Technical data and requirements

Parts category DIN EN ISO 9227 NSS (h)

DIN 50018 AHT Corrosion
Coating with or
PV Surface Sealing until Zn until Fe 2,0 S resistance
metal without
cycles until (Kb)
thread
Corrosion Fe corrosion

.15 Without Transparent 168 A) 360 A) 5 IV

Permissible
passivated
.16 With 96 A) 240 A) 3 III
Zn Only for
.12 Without 48 120 5
Silver-colored interior parts
Permissible
passivated Only for
.22 With 24 72 3
interior parts
Only for
.13 Zn or ZnFe All Black passivated Yes 168 360 5
interior parts
.86 Without Yes 360 A) 600 A) 5 V
ZnFe Transparent passivated
.96 With Permissible 120 A) 480 A) 3 III to IV

.66 Without Permissible 240 A) 720 A) 2 V to VI

.62 Without No 240 A) 720 A) 2 V to VI

.65 ZnNi Without Transparent passivated Yes 360 A) 720 A) 2 V to VI

.76 With Permissible 120 A) 720 A) 1 IV to V

A) A)
.72 With No 120 720 1 IV to V

.19 Without 240 480 V to Vl

Zn
.29 With Duplex coating (metallic base coat, 168 240 IV to V
: Witold Rybak, 2016-04-27

passivated + organic
.69 Without top coat) 480 720 Vl
ZnNi
.79 With 360 720 Vl

A) Requirements shall also be met after heat treatment for 24 h at 120 °C

Copyright Daimler AG
Uncontrolled copy when printed

DBL 8451:2015-06 page 14

Annex A (normative)
Comparison table for substitution of Cr(VI) coatings with Cr(VI)-free coatings

To avoid the effort of drawing modifications for a majority of the components concerned, a substitution list, according to which the corrosion protection requirements
of certain product versions are changed to those of Cr(VI)-free coatings, is hereby defined.

Due to the specifications of the current EU chemicals directive (REACH), when using chromic acid it is to be anticipated that the production of corrosion protective
coatings with conversion layers containing Cr(VI) on galvanically produced zinc and zinc alloy coatings will be fundamentally discontinued in European electroplating
operations not later than September 2017. As a result, the coating systems produced in the EU zone and specified on a large number of commercial vehicle
component drawings will no longer be available for commercial vehicles either.

To avoid modifying individual design drawings for a majority of the components concerned, the comparative substitution list shows Cr(VI)-free surfaces with similar
technological properties as possible alternatives to the product versions containing Cr(VI) and still used in commercial vehicles.
The technology used for producing Cr(VI)-free surfaces is similar in the majority of cases, i.e. the base coat specifications are identical, with differences only arising
in the final conversion treatments. Thus, Cr(VI)-based chromating is transformed into Cr(VI)-free passivation. However, this also changes the surface color and
anti-corrosion properties.

The basic system is also changed in some substitution specifications. For example, a galvanic base coat is transformed into a zinc flake base coat as per
the standard coating on our metric screws (DBL 9440.40). Due to the specific requirements for friction behavior, the drawing entry shall also be modified via
the component manager in this case.
: Witold Rybak, 2016-04-27

Copyright Daimler AG
Uncontrolled copy when printed

DBL 8451:2015-06 page 15

For components in which surface protection product versions (PV) according to DBL 8451 can result in the application of Cr(VI)-based
chromating, these product versions shall be substituted with product versions with Cr(VI)-free passivation as per the following scheme.
Substitution list for transition of Cr(VI)-based chromating to Cr(VI)-free coating systems
Requirement
Initial PV Substitution PV
(containing Cr(VI)) (Cr(VI)-free)

Group according to according to Corrosion protection

DBL 8451:2008-09 DBL 8451:2015-04 of the Cr(VI)-free coating Color scheme
A 8451.11 8451.15 Slightly better Yellow becomes silver

8451.21 8451.16 Slightly better Yellow becomes silver

8451.18 8451.15 Very similar Yellow becomes silver
8451.28 8451.16 Very similar Yellow becomes silver
8451.68 8451.65 Requirement identical Yellow becomes silver
8451.78 8451.76 Requirement up to Zn corrosion lower Yellow becomes silver
8451.61 8451.66 Requirement identical Yellow becomes silver
8451.71 8451.76 Requirement up to Zn corrosion lower Yellow becomes silver
8451.83 8451.69 Better due to org. top coat Black is retained
8451.93 8451.79 Better due to org. top coat Black is retained

B 8451.25 9440.40 shall be checked by component manager; a new drawing entry is required
8451.75 9440.40 shall be checked by component manager; a new drawing entry is required
8451.97 9440.xx shall be checked by component manager; a new drawing entry is required, e.g. 9440.50
: Witold Rybak, 2016-04-27

C 8451.14
No direct substitution; seek a new solution with component manager
Olive
if necessary
No direct substitution; seek a new solution with component manager
8451.24 Olive
if necessary

Copyright Daimler AG
Uncontrolled copy when printed

DBL 8451:2015-06 page 16

Procedure based on an example for group A:

• Supplier announces its intention to discontinue chromating on 1.10.2016 to the responsible Daimler AG supplier management department. The time up to
the discontinuation of chromating shall not be less than 6 months.
• The supplier informs Daimler (responsible supplier manager of the component or component group concerned) of the specific chromating discontinuation
date and its initial sampling result for the components as per Section 8 of this DBL, which it has coated and tested according to substitution PV 8451.xx
from the above table. This information shall be available at least 3 months prior to the changeover date.
• Daimler approves the initial/new samples.

Procedure based on an example for group B:

• Supplier announces its intention to discontinue chromating on 1.10.2016 to the responsible Daimler AG supplier management department. The time up
to the discontinuation of chromating shall not be less than 12 months.
• The Daimler AG supplier management department informs the Development department responsible for the component (component manager) and asks
it to define a DBL 9440 product version with screw technology properties which can replace those applied so far as per DBL 8451. The component manager
modifies the drawing (at least 6 months prior to changeover) and the supplier is informed.
• The supplier performs sampling and delivers according to the new specifications after sample approval by Daimler AG

Procedure based on an example for group C:

• Supplier announces its intention to discontinue chromating on 1.10.2016 to the responsible Daimler AG supplier management department. The time up
to the discontinuation of chromating shall not be less than 12 months.
• The Daimler AG supplier management department informs the Development department responsible for the component (component manager) and asks
it to define the DBL or possibly another standard which specifies the surface protection method suitable for the application.
• The component manager modifies the drawing (at least 6 months prior to changeover) and the supplier is informed.
• The supplier performs sampling and delivers according to the new specifications after sample approval by Daimler AG.

As of 1.7.2017, all components previously designed according to this DBL with Cr(VI)-based chromating shall be supplied with Cr(VI)-free passivation as per
the substitution product versions in this DBL. The relevant sampling process shall also be completed by then.

Daimler department responsible for this topic:

Trucks, Vehicle Concepts Corrosion Protection
: Witold Rybak, 2016-04-27

Copyright Daimler AG