DTK7268
DTK7268
DTK7268
Overview
Description
The DTK7268 Indoor gateway is a full 8-channel indoor gateway, based on the LoRaWAN protocol, with built-in
Ethernet connectivity for a straightforward setup. There is an on-board Wi-Fi setup (supporting 2.4 GHz Wi-Fi) that
allows it to be easily configured via the default Wi-Fi AP mode. Additionally, the gateway supports LTE uplink
communication connections (optional).
It also supports MQTT Bridge mode, with the option for TLS authentication.
Power-over-Ethernet (PoE) is supported to serve cases where wall or ceiling mounting is required without the
need to install additional power lines.
The open-source software for the management and configuration of this gateway device is based on OpenWRT. It
has a built-in LoRa packet forwarder and a graphical user interface, allowing for a quick set-up without giving up
the freedom of a fully customized solution.
DTK7268 also supports the MQTT Bridge function, can use the MQTT integrated to third-party platforms.
DTK7268 is especially suitable for small and medium-sized deployment scenarios in industry applications, saving
the additional cost for server and R&D investment, and has the advantages of high execution efficiency.
Features
Specifications
Overview
The overview presents the block diagram for the DTK7268 that shows the internal architecture of the board.
Hardware
The hardware specification covers only the interfacing of the DTK7268 and its corresponding functionalities. It also
presents the parameters and the standard values of the board.
Interfaces
The hardware interfaces of RAK7268 gateway include DC 12 V, ETH interface, Console interface, Reset key, TF
Card slot, Status indicator LEDs, LoRa Antenna connector, etc.
LED Indicators
LEDs Status Indication Description
ON - Linkup
ON - LoRa is working
AP Mode:
-ON - The AP is up
-ON - Connected
Main Specifications
Feature Specifications
8 Channels
Frequency: EU433/CN470/EU868/US915/AS923/AU915/IN865/KR920
- WCDMA: B1/B8
- WCDMA: B2/B4/B5
DC 12 V - 1 A
Power supply
PoE (IEEE 802.3 af), 36~57 VDC
POWER LED
WLAN LED
LTE LED
Weight 0.3 kg
Dimension 166x127x36 mm
RF Specifications
Wi-Fi Radio Specifications
Feature Specifications
802.11b
802.11g
802.11g
802.11n (2.4G)
Feature Specifications
Feature Specification
Electrical Requirements
The Gateway comes with a 12 V-1 A power adaptor. It also fully compatible with PoE (IEEE 802.3af), 36~57 VDC.
Environmental Requirements
The casing is IP30 rated and is made of plastic. There are holes for a mounting bracket on the back, in order to
simplify wall mounting. The enclosure, while robust, is not meant for outdoor deployment and should be kept away
from moisture.
Parameter Value
Dimensions 66x127x36 mm
Weight 0.3 kg
Software
Firmware
The firmware sits on OpenWRT, which makes it possible to customize it. There is a Web UI for easy configuration
and management of the device, as well as the possibility for SSH2 management.
Model Firmware Version Source
Software Features
LoRaWAN Network Management
Data logger Router module NAT Configuring the LoRa Packet Forwarder
Certification
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
📝 NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, according
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used following the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
ISEDC Warning
This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
2. This device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
The device complies with RF exposure guidelines, users can obtain Canadian information on RF exposure and
compliance. The minimum distance from the body to use the device is 20 cm.
Le présent appareil est conforme Après examen de ce matériel aux conformité ou aux limites d’intensité de champ
RF, les utilisateurs peuvent sur l’exposition aux radiofréquences et la conformité and compliance d’acquérir les
informations correspondantes. La distance minimale du corps à utiliser le dispositif est de 20 cm.