Activity Sheets 3

INFORMATION AND COMMUNICATIONS TECHNOLOGY (ICT) 9

WEEK 1-2

Student’s Name: ___________________________ Contact Number: _____________

Address: __________________________________ Year & Section: ______________

Lesson 1 │ Activity 1: MODIFIED TRUE OR FALSE (20 POINTS)

Note: Please refer to pages 2-5 in your module

Direction: Write TRUE if the statement is correct and FALSE otherwise. Write your
answer on the space provided.

_____1. Always disconnect a computer from the AC power and from any powered
peripherals while you are working on it.
_____2. Always grasp a metal part of the computer chassis with your bare hand before
you touch anything inside. Do this even if you are wearing an anti-static
wristband.
______3. Always handle electronic components by a non-conducting (nonmetallic) edge.
Don't touch the pins or other connectors.
______4. Always use a UL-approved surge protector or an Uninterruptible Power Supply
that incorporates surge and spike protection.
______5. Never use an anti-static wrist strap when working on a computer (except when
working on monitors)
______6. Everyone is allowed to eat, drink, or smoke while working on a computer.
_____7. Never plug an ATX power supply into AC power unless it is connected either to
a computer's motherboard or to a dummy test load.
______8. Static electricity is the discharge of electricity between two objects with
different electrical potential.
______9. Apron is a garment worn over the front of the body as a protection for one’s
cloth.
______10. PPE can also be used to protect the working environment from pesticide
application, pollution or infection from the worker.

Lesson 1 │ Activity 2: MULTIPLE CHOICE: Read each question carefully and

choose the letter of the best answer. Write your answer on the space provided. (20
POINTS)
Note: Please refer to pages 3-6 in your module.

______1. Which of the following is not a Windows XP minimum requirement?

a. 128MB RAM or higher c. Lower resolution monitor
b. CD- ROM or DVD ROM d. 4.3 GB hard disk space or more
______2. If you see a message to press any key to boot the CD and you fail to do so,
what do you think will happen?
a. The computer will restart c. It will be prompted to BIOS setup
b. Set up inspecting your system will appear d. It will return to boot menu
______3. What key should you press if you need to install any third- party or RAID
drivers?
a. F2 c. F2
b. F6 d. F12
______4. After reading the license agreement, what function key will press in order to
start the installation?
a. F6 c. F9
b. F8 d. F12
______5. Where do we typically install the operating system?
a. Drive C c. External Drive
b. DVD d. Floppy Drive
______6. What file system is usually used during installation?

Note: No part of this material may be reproduced in any form or by any means without permission from
XKHS.
 Activity Sheets 3

a. FAT c. NTFS
b. FAT32 d. NTFS32
______7. Suppose that you will install Windows XP on a system with more than one
partition, what important process should be done?
a. Change the file system
b. Delete the data and files on the different partition
c. Examine the partition
d. Format the correct partition
______8. When the folder copy phase is complete your system will reboot, what are you
going to do if you will see the message “Press any key to boot from CD”?
a. Press any key c. Reboot the system
b. Do not press a key d. Eject the CD
______9. What is the next phase after the set-up folder copy phase and reboot?
a. GUI set up c. Username setup
b. Software d. Software personalization
_____10. What phase will immediately follow after the first boot phase?
a. Welcome to Windows c. Change display setting
b. Network Setup d. Set up users

Lesson 1 │ Activity 3: REARRANGE THE PROCEDURES (20 POINTS)

Note: Please refer to pages 5-8 in your module

Direction: Rearrange the following procedures in their proper order. The procedures
listed below describe how to obtain and install drivers for hardware devices on a
Microsoft Windows XP Installation. Write your answer on the space provided before
each number.

A. Use number from 1-5 to indicate their order of precedence.

___ Welcome to Setup
___ Read the license agreement
___ Choose an installation partition
___ MS-DOS portion of Setup begins
___ Insert the Windows XP CD-ROM and reboot the computer
B. Use number from 6-10 to indicate their order of precedence.
___ Select the file system
___ Optionally format the partition
___ GUI Setup begins
___ Setup folder copy phase and reboot
___ Regional and language Options

Lesson 1 │ Activity 4: (30 POINTS)

Note: Please refer to pages 5-8 in your module

Direction: For you to have a profound knowledge on the overview of what windows XP
is, form a group with 5 members and utilize the internet and watch the following video
presentations:

1. Overview of Windows XP
2. Planning for installation
3. Windows XP installation

After watching the videos, have a documentation containing the overview of

Windows XP and salient procedures in planning for installation and Windows XP
installation. Use a short white bond paper and be creative for the documentation.

Note: No part of this material may be reproduced in any form or by any means without permission from
XKHS.
 Activity Sheets 3

INFORMATION AND COMMUNICATIONS TECHNOLOGY (ICT) 9

WEEK 3-4

Student’s Name: ___________________________ Contact Number: _____________

Address: __________________________________ Year & Section: ______________

Lesson 1 │ Activity 5: TRUE OR FALSE (30 POINTS)

Note: Please refer to pages 3-8 in your module.

Direction: Write TRUE if the statement is correct and FALSE otherwise. Write your
answer on the space provided.
___1. Always use an anti-static wrist strap when working on a computer (except when
working on monitors)
___2. Always disconnect a computer from the AC power and from any powered
peripherals while you are working on it.
___3. Always grasp a metal part of the computer chassis or case with your bare hand
before you touch anything inside. Do this even if you are wearing an anti-static
wristband.
___4. Always handle electronic components by a non-conducting (nonmetallic) edge.
Don't touch the pins or other connectors.
___5. Always use a UL-approved surge protector or an Uninterruptible Power Supply
that incorporates surge and spike protection
___6. Never eat, drink, or smoke while working on a computer.
___7. Whenever you purchase software or hardware for your computer, you should
first make sure your computer supports the system requirements.
____8. The speed of a computer's processor chip (technically known as its "clock
speed") in measured in gigahertz (GHz).
____9. A computer's graphics system determines how well it can work with visual
output.
___10. Today 40GB is an absolute minimum hard drive size for a new computer
running Windows 7.
___11. When attaching cables, never force a connection.
___12. BIOS instruct the computer on how to perform a number of basic functions
such as booting and keyboard control.
___13. The external visual inspection consists of a quick inspection of the interior of
the computer.
___14. Disk management tools help detect and correct disk errors.
___15. The most basic test is to switch the system on to check it starts without errors.

Lesson 1 │ Activity 6: MULTIPLE CHOICES (20 POINTS)

Note: Please refer to pages 8-11 in your module.

Direction: Read each question carefully and write the letter of the best answer. Write
your answer on the space provided.
_____1. What are the small software programs that help the operating system use the
device?
a. Installer b. Application c. Driver d. BIOS
_____2. Which of the following is software shared on a small memory chip on the
motherboard?
a. Installer b. Application c. driver d. BIOS
____3. Which of the following is the way to set up a system or the assortment of
components that make up the system?
a. Configuration b. Set up c. Driver d. Installation
_____4. Which of the following is not a Windows XP minimum requirement?
a. 128MB RAM or higher c. Lower resolution monitor

Note: No part of this material may be reproduced in any form or by any means without permission from
XKHS.
 Activity Sheets 3

b. CD- ROM or DVD ROM d. 4.3 GB hard disk space or more

_____5. If you see a message to press any key to boot the CD and you fail to do so,
what do you think will happen?
a. The computer will restart c. It will be prompted to BIOS setup
b. Set up inspecting your system will appear d. It will return to boot menu
_____6. What key should you press if you need to install any third- party or RAID
drivers?
a. F2 b. F6 c. F9 d. F12
_____7. Where do we typically install the operating system?
a. Drive C b. DVD c. External Drive d. Floppy Drive
_____8. Suppose that you will install Windows XP on a system with more than one
partition, what important process should be done?
a. Change the file system c. Examine the partition
b. Delete the data and files on the different partition d. Format the correct partition
_____9. What file system is usually used during installation?
a. FAT b. FAT32 c. NTFS d. NTFS32
_____10. Which of the following is a connector on the back of a computer or other
device?
a. Modem b. Port hub c. Router d. Network Gateway

Note: No part of this material may be reproduced in any form or by any means without permission from
XKHS.
 Activity Sheets 3

INFORMATION AND COMMUNICATIONS TECHNOLOGY (ICT) 9

WEEK 5-6

Student’s Name: ___________________________ Contact Number: _____________

Address: __________________________________ Year & Section: ______________

Lesson 2 │ Activity 7: MATCHING TYPE (10 POINTS)

Note: Please refer to pages 11-14 in your module

Direction: Match Column A with Column B and write your answer in the space
provided.

Column A Column B

____1. It is a device that can take many types of measurements. a. Digital

____2. Also called a loopback plug, tests the basic functionality multimeter
____3. A two-part tool. b. Loopback
____4. A command-line tool that creates and deletes partitions adapter
on a hard drive. c. Toner probe.
____5. Prepares a hard drive to store information. d. FDISK
____6. Optimizes space on a hard drive to allow faster access to e. Format
programs and data. f. Defrag
____7. Clears space on a hard drive by searching for files that g. Disk Cleanup
can be safely deleted. h. CHKDSK

____8. Checks the integrity of files and folders on a hard drive by I. Disk Management

scanning the file system. Tool

____9. Initializes disks, creates partitions, and formats partitions. j. SFC
____10. A command-line tool that scans the operating system
critical files and replaces files that are corrupted.

Lesson 2 │ Activity 8: ICT JUMBLE TEST (20 POINTS)

Note: Please refer to pages 11-14 in your module

Directions: Unscramble the mixed-up words to find a series of computer terms. Write
your answer on the space provided before each number.
1. MSYTES LIFE HECCREK – _________________________
2. SIDK- _______________________
3. RAMFOT- _________________________
4. FRAGED- ________________________
5.NOIAGDICTS LOTOS– __________________
6. LLATANSITION– ___________________
7. TIMULREMET- ________________
8. WARETOFS LOTOS-__________________________
9. EBPRO RONET-______________________________
10. DEL-__________________________________

Note: No part of this material may be reproduced in any form or by any means without permission from
XKHS.