This document summarizes the technical specifications of Jotun Epoxy Mastic, a two-component, polyamine cured epoxy coating. It is a high-solids, high-build product designed for areas where optimal surface preparation is difficult. Typical uses include marine vessel exteriors and interiors. The product has a solids content of 78% by volume, dries to touch in 5 hours at 23°C, and is heat resistant up to 90°C continuously. It can be applied by airless spray and is available in packs of 20L for Component A and 5L for Component B.
This document summarizes the technical specifications of Jotun Epoxy Mastic, a two-component, polyamine cured epoxy coating. It is a high-solids, high-build product designed for areas where optimal surface preparation is difficult. Typical uses include marine vessel exteriors and interiors. The product has a solids content of 78% by volume, dries to touch in 5 hours at 23°C, and is heat resistant up to 90°C continuously. It can be applied by airless spray and is available in packs of 20L for Component A and 5L for Component B.
This document summarizes the technical specifications of Jotun Epoxy Mastic, a two-component, polyamine cured epoxy coating. It is a high-solids, high-build product designed for areas where optimal surface preparation is difficult. Typical uses include marine vessel exteriors and interiors. The product has a solids content of 78% by volume, dries to touch in 5 hours at 23°C, and is heat resistant up to 90°C continuously. It can be applied by airless spray and is available in packs of 20L for Component A and 5L for Component B.
This document summarizes the technical specifications of Jotun Epoxy Mastic, a two-component, polyamine cured epoxy coating. It is a high-solids, high-build product designed for areas where optimal surface preparation is difficult. Typical uses include marine vessel exteriors and interiors. The product has a solids content of 78% by volume, dries to touch in 5 hours at 23°C, and is heat resistant up to 90°C continuously. It can be applied by airless spray and is available in packs of 20L for Component A and 5L for Component B.
Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product. Specially designed for areas where optimum surface preparation is not possible or desired. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and aged coating surfaces.
Typical use Marine: Outside hulls, exterior and interior areas. Other
Colors black, grey, red
Product data Property Test/Standard Description Solids by volume ISO 3233 78 ± 2 % Gloss level (60 °) ISO 2813 semi gloss (35-70) Flash point ISO 3679 Method 1 95 °F (35 °C) VOC-USA / VOC Hong Kong EPA Method 24 2,2 lbs/gal
The provided data is typical for factory produced products, subject to slight variation depending on color. All data is valid for mixed paint. Gloss level: According to Jotun Performance Coatings' definition.
Recommended film thickness per coat
Film thickness and Dry film thickness Wet film thickness Theoretical spreading rate spreading rate mils (μm) mils (μm) ft²/gl (m²/l)
Surface preparation To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination.
Date of issue: 3 November 2014 Page: 1/4
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com Technical Data Sheet Jotun Epoxy Mastic
Surface preparation summary table
Surface preparation
Substrate Minimum Recommended
Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1)
Shop primed steel Clean, dry and undamaged shop Sa 2 (ISO 8501-1) primer (ISO 12944-4 6.1) Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)
Walk-on-dry 42 h 18 h 12 h 8 h 3 h Dried to over coat, minimum 42 h 18 h 12 h 8 h 3 h Dried/cured for service 48 d 24 d 14 d 7 d 5 d
Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and within the DFT range of the product.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the surface.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks, imprints or other physical damage.
Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.
Date of issue: 3 November 2014 Page: 2/4
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com Technical Data Sheet Jotun Epoxy Mastic
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended environment/medium.
Induction time and Pot life
Temperature: 23°C = 73°F
Paint temperature 23 °C
Induction time 10 min
Pot life 1h
Heat resistance Temperature Continuous Peak
Dry, atmospheric 90 °C 90 °C Immersed, sea water 50 °C 60 °C
Peak temperature duration max. 1 hour.
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures. Note that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If used as part of a system, ensure all coatings in the system have similar heat resistance.
Product compatibility Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Jotun for specific system recommendation.
Packaging (typical) Volume Size of containers (liters) (liters)
Jotun Epoxy Mastic Comp A 16 20
Jotun Epoxy Mastic Comp B 4 5
4 l = 1.06 gal 16 l = 4.23 gal
The volume stated is for factory made colors. Note that local variants in pack size and filled volumes can vary due to local regulations.
Date of issue: 3 November 2014 Page: 3/4
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com Technical Data Sheet Jotun Epoxy Mastic
Storage The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care.
Shelf life at 73°F (23 °C)
Jotun Epoxy Mastic Comp A 48 month(s) Jotun Epoxy Mastic Comp B 24 month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to re-inspection.
Caution This product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the work.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Color variation Products primarily meant for use as primers and antifoulings may have slight color variations from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.
Disclaimer The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and practical experience. Jotun's products are considered as semi-finished goods and as such, products are often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom) version will prevail.
Date of issue: 3 November 2014 Page: 4/4
This technical data sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
