Taurus 38
Taurus 38
Taurus 38
ATTENTION
THIS BOOKLET
The safety warnings in this booklet are important. By understanding the dangers inherent in the use of any firearm, and by taking the precautions described herein, you can enjoy complete safety in the use of your Taurus firearm. Failure to heed any of these warnings may result in serious injury to you or others, as well as severe damage to the firearm or other property.
CONTENTS
1. Safety precautions 2. Ammunition 3. Taurus Security System 4. Revolver Operation 5. Care and maintenance 6. Exploded view Parts list 7. Taurus Limited Warranty 8. Taurus Service Policy
SAFETY PRECAUTIONS
DANGEROUS WEAPONS
REVOLVERS, PISTOLS and RIFLES are classified as FIREARMS or DANGEROUS WEAPONS and are sold by us with the specific understanding that we are not responsible in any manner whatsoever for their improper or negligent handling or resale under local laws and regulations. TAURUS shall not be responsible in any manner whatsoever for malfunctioning of the firearm, or for physical injury or property damage, resulting in whole or in part from (1) criminal or negligent discharge, (2) improper or careless handling, (3) unauthorized modifications, (4) defective, improper handloaded, or reloaded ammunition, (5) neglect, or (6) other influences beyond our direct and immediate control. This limitation applies regardless of whether liability is asserted on the basis of contract, negligence or strict liability (including any failure to warn). Under no circumstance shall Taurus be liable for incidental or consequential damages, such as loss of use of property, commercial loss and loss of earnings or profits.
04
Taurus firearms are designed and made to offer maximum safety when correctly used. However, as with any other firearm, it is not foolproof, and may become very dangerous if the following basic recommendations are not RIGIDLY observed:
ATTENTION
1. DANGER: Never, never-ever point any firearm, loaded or unloaded, at anything you do not intend to shoot. 2. WARNING: Always treat every firearm as if it were loaded. 3. NOTICE: Get instruction from a competent firearms instructor before using any firearm. 4. SAFETY FIRST: The safety is only a mechanical device, not a substitute for common sense. 5. WARNING: Keep your finger off the trigger until you are actually aiming at the target ready to shoot. 6. WARNING: Be certain that the firearm is unloaded before cleaning. 7. WARNING: Always empty firearms before entering a place where there are people. 8. SAFETY FIRST: Never leave a loaded firearm unattended. 9. SAFETY FIRST: Store firearms and ammunition separately beyond the reach of children. 10. WARNING: Dont test the safety by pulling the trigger while the safety is on unless you are absolutely sure the firearm is empty and you are pointing away from everyone. 11. SAFETY FIRST: Be sure of your target and backstop before you shoot. 12. WARNING: Firearms and alcohol or drugs dont mix. Do not shoot or handle firearms after consuming beer, wine, other alcoholic beverages or any medications or other drugs that may affect your ability.
05
13. WARNING: Never pull a firearm towards you by the muzzle. Dont climb a tree or cross a fence with a loaded firearm. 14. DANGER: Load and unload with the muzzle pointed in a safe direction. 15. SAFETY FIRST: If a firearm fails to fire when the trigger is pulled, keep it pointed at the target for at least 30 seconds. Sometimes slow primer ignition will cause a hang fire and the cartridge will go off after a short pause. 16. SAFETY FIRST: Never shoot at hard flat surfaces or water, bullet may ricochet. 17. DANGER: When receiving a firearm always check that it is unloaded (Pistols: Remove magazine and open slide to check if chamber is empty. Revolvers: Open cylinder to check if it is empty), even if you saw it done previously. 18. DANGER: Never put your hand over the muzzle of a firearm. 19. DANGER: Check ammunition to be sure it is the right size and caliber, and that it is not dented. 20. SAFETY FIRST: Use a proper holster and draw only if you intend to shoot. 21. NOTICE: Never cock the firearm until you are ready to shoot. 22. SAFETY FIRST: Dry firing is bad for this firearm, whether the hammer block is engaged or not. 23. DANGER: WHILE HANDLING ANY FIREARM, NEVER ALLOW IT TO POINT AT ANY PART OF YOUR BODY OR AT ANOTHER PERSON. NO HARM SHOULD RESULT IF YOU OBEY THIS RULE, EVEN IF AN ACCIDENTAL DISCHARGE OCCURS. 24. CAUTION: If there is any reason to suspect that a bullet is obstructing the barrel, immediately unload the firearm and look through the bore. It is not sufficient to merely look in the chamber. 25. SAFETY FIRST: Treat this firearm as a precision instrument. 26. WARNING: Old or reloaded ammunition may be dangerous. We recommend against using it. 27. WARNING: Never carry any handgun in your pocket, purse or waistband. Use a pistol case or proper holster with safety flap or strap. 28. DANGER: Dont try to change your firearms trigger pull, because alteration of trigger pull usually affects sear engagement and may cause accidental discharge. 29. SAFETY FIRST: Write to us concerning any items or circumstances which might relate to your safety and the operation of our products. 30. DANGER: Never engage a gun lock on a loaded firearm.
06
DANGER
Always wear adequate shooting glasses and ear plugs or ear muff type protectors whenever you are shooting. Always make certain that persons close to you are similarly protected. Unprotected eyes may be injured by powder, gas, carbon residue, lubricant, metallic particles or similar debris which may emanate occasionally from any firearm in normal use. Without ear protection, repeated exposure to shooting noise will lead to cumulative, permanent hearing loss.
07
WARNING AMMUNITION
1. Use only high quality, original, factory-manufactured ammunition. Do not use cartridges that are dirty, wet, corroded, bent or damaged. Do not oil cartridges. Do not spray aerosoltype lubricants, preservatives, or cleaners directly onto cartridges or where excess spray may flow into contact with cartridges. Lubricant or other foreign matter on cartridges can cause potentially dangerous ammunition malfunctions. Use only ammunition of the caliber for which your firearm is chambered. The proper caliber is permanently engraved on your firearm; never attempt to use ammunition of any other caliber. 2. The use of reloaded, remanufactured, hand-loaded, or other nonstandard ammunition voids all warranties. Improperly loaded ammunition voids all warranties. Improperly loaded ammunition can be extremely dangerous. Severe damage to the firearm and serious injury to the shooter or to others may result. Always use ammunition that complies with the industry performance standards established by the Sporting Arms and Ammunition Manufacturers Institute, Inc., of the United States, (SAAMI) or the equivalent from other countries (i.e. C.I.P.). 3. Firearms may be severely damaged and serious injury to the shooter or to others may result from any condition causing excessive pressure inside the chamber or barrel during firing. Excessive pressure can be caused by obstructions in the barrel, propellant powder overloads, or by the use of incorrect cartridges or defectively assembled cartridges. In addition, the use of a dirty, corroded, or damaged cartridge can lead to a burst cartridge case and consequent damage to the firearm and personal injury from the sudden escape of high-pressure propellant gas within the firearms mechanism. 4. Immediately stop shooting and check the barrel for a possible obstruction whenever: You have difficulty in, or feel unusual resistance in, chambering a cartridge, or A cartridge misfires (does not go off), or The mechanism fails to extract a fired cartridge case, or Unburned grains of propellant powder are discovered spilled in mechanism, or A shot sounds weak or abnormal. In such cases it is possible that a bullet is lodged part way down the barrel. Firing a subsequent bullet into the obstructed barrel can wreck the firearm and cause serious injury to the shooter or to bystanders. 5. Bullets can become lodged in the barrel. If the cartridge has been improperly loaded without propellant powder, or if the powder fails to ignite (Ignition of the cartridge primer alone will push the bullet out the cartridge case, but usually does not generate sufficient energy to expel the bullet completely from the barrel). If the bullet is not properly seated tightly in the cartridge case. When such a cartridge is extracted from the chamber without being fired, the bullet may be left behind in the bore at the point where the rifling begins. Subsequent chambering of another cartridge may push the first bullet further into the bore. 6. If there is any reason to suspect that a bullet is obstructing the barrel, immediately unload the firearm and look through the bore. It is not sufficient to merely look in the chamber. A bullet may be lodged some distance down the barrel where it can not easily be seen. IF A BULLET IS IN THE BORE, DO NOT ATTEMPT TO SHOOT IT OUT BY USING ANOTHER CARTRIDGE, OR BY BLOWING IT OUT WITH A BLANK OR ONE FROM WHICH THE BULLET HAS BEEN REMOVED. SUCH TECHNIQUES CAN GENERATE EXCESSIVE PRESSURE, WRECK THE FIREARM AND CAUSE SERIOUS PERSONAL INJURY. If the bullet can be removed with a cleaning rod, clean any unburned powder grains from
08
the bore, chamber, and mechanism before resuming shooting. If the bullet cannot be dislodged by tapping it with a cleaning rod, take the firearm to a gunsmith. 7. Dirt, corrosion, or other foreign matter on a cartridge can impede complete chambering and may cause the cartridge case to burst upon firing. The same is true of cartridges which are damaged or deformed. 8. Do not oil cartridges, and be sure to wipe the chamber clean of any oil or preservative before commencing to shoot. Oil interferes with the friction between cartridge case and chamber wall that is necessary for safe functioning, and subjects the firearm to stress similar to that imposed by excessive pressure. 9. Use lubricants sparingly on the moving parts of your firearm. Avoid excessive spraying of any aerosol firearm care product, especially where it may get on ammunition. All lubricants and aerosol spray lubricants in particular, can penetrate cartridge primers and cause misfires. Some highly penetrative lubricants can also migrate inside cartridge cases and cause deterioration of the propellant powder; on firing, the powder may not ignite. If only the primer ignites, there is danger that the bullet may become lodged in the barrel. Taurus revolvers were designed to use cartridges loaded to the limits shown below. Other cartridges of various types or bullet weights may or may not function acceptably; such ammunition should be thoroughly tested by the user before relying on it. Because of the widely differing specifications of such other ammunition, Taurus cannot be responsible for malfunctions resulting from its use. CAUTION Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to cause birth defects, reproductive harm, and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure. NOTICE: You can use .38 Special ammunition in all Taurus revolver chambered for .357 Magnum; .44 Special ammunition in Taurus revolvers chambered for .44 Magnum and .45 Long Colt in Taurus revolvers chambered for .454 Casull. It is important to note that these are the only caliber substitutions that will function. Attempting to substitute other calibers can damage your firearm and may result in accidental death or serious injury. NOTICE: The Taurus .357 Magnum Total Titanium Revolvers (Models 617 and 627) have been extensively tested with various .357 Magnum cartridges. We have determined that .357 Magnum catridges which utilize bullet weights of at least 125 grains are perfectly suitable to be fired in your revolver. NOTICE: .357 Magnum cartridges with bullet weights of less than 125 grains have resulted in cylinder face erosion and should not be utilized in your Total Titanium revolver. WARNING Securing your firearm may inhibit access to it in a defense situation and result in injury or death. WARNING To prevent injury or death, it is imperative that you must keep your gun unloaded, uncocked, and securely locked, with ammunition in a separate location. In addition, take any other reasonable steps to limit the possibility of theft, accident, or suicide. WARNING Failure to properly secure a firearm may result in injury or death.
09
WARNING concerning ammunition marked +P and +P+. Recently there have been many developments by ammunition manufacturers and reloaders, not all of them good. It seems some ammunition manufacturers and reloaders are in a horsepower race to see who can develop the most case pressure and muzzle velocity with little regard for practicality or safety. Some of these loads exceed common sense and can virtually tear metal apart. Taurus Firearms rated for +P ammunition are rated for Sporting Arms and Ammunition Manufacturers Institute (SAAMI) compliant +P ammunition. SAAMI does not recognize any +P+ ammunition at all. It is DANGEROUS to fire +P+ ammunition in any Taurus firearm and if you do so you may be seriously injured or killed. In addition, it seems some ammunition marked +P is not SAAMI compliant either. There are only four calibers that can carry a +P rating from SAAMI. They are 38 Special +P 9mm Luger +P 38 Super Automatic and 45 Automatic +P There are no , , . other SAAMI approved +P loads. Any ammunition in any other caliber marked +P is not SAAMI compliant, may be dangerous and should not be used. Whenever you are buying +P ammunition, look for a notation on the box that states that the ammunition is SAAMI compliant! DANGER for +P+ Never use Plus -P -Plus (+P+) rated ammunition in any Taurus firearm. The Sporting Arms and Ammunition Manufacturers Institute (SAAMI) does not recognize such ratings and such ammunition can be very dangerous. Firing such ammunition can cause catastrophic failure in firearms resulting in serious bodily injury or death. WARNING for +P Only fire SAAMI rated Plus P (+P) ammunition in Taurus Models designated by Taurus for +P use. Firing +P ammunition in other Taurus products may be dangerous and can result in serious bodily injury or death. Those Models are: Model 85 small frame revolver in 38 Special. Model 850 small frame revolver in 38 Special. Model 851 small frame revolver in 38 Special. Model 85 Polymer small frame revolver in 38 Special. Model 82 medium frame revolver in 38 Special. Model 817 medium frame revolver in 38 Special. All firearms chambered in 38 Super Automatic. All firearms chambered in 45 Automatic. (ACP) All firearms chambered in 9mm Luger. WARNING Even if your Taurus firearm is rated for Plus-P (+P) ammunition, such ammunition generates pressures significantly in excess of the pressures associated with standard ammunition. Such pressures may affect the useful life of the firearm or exceed the margin of safety built into many firearms. Unless you need +P ammunition, do not use it, particularly for practice.
10
LOADING
1. DANGER: Always make sure the muzzle is pointed in a safe direction. 2. SAFETY FIRST: Never attempt to load or unload any firearm inside a vehicle, building or other confined space (except a properly constructed shooting range). Enclosed areas frequently do not offer a completely safe direction to point the firearm; if an accidental discharge occurs, there is a great risk of injury or property damage. 3. SAFETY FIRST: Before loading, always clean all grease and oil from the bore and chamber, and check to be certain that no obstruction is in the barrel. Any foreign matter in the barrel could result in a bulged or burst barrel or other damage to the firearm, and could cause serious injury to the shooter or to others.
FIRING
1. DANGER: Keep the muzzle pointed in a safe direction and your finger away from the trigger when cocking any firearm. 2. WARNING: Never carry, handle or leave unattended any firearm which is cocked and ready to fire. When cocked, it will fire from slight pressure on the trigger. An accidental discharge could easily result if you fall or drop the firearm, or if the firearm is struck or disturbed by someone or something. 3. WARNING: Never fire any revolver with your finger, hand, face, or other part of your body over or adjacent to the cylinder gap between the cylinder face and the forcing cone. The release of excess gases and hot particles from that point are part of the normal operation of revolvers, and pose no safety hazard to the shooter if the firearm is held in a normal grip and fired at arms length (in the case of a handgun) as intended by its design. 4. CAUTION: Never allow other persons to stand beside you where they might be struck by ejected particles or gases. These are hot, and may be ejected with sufficient force to cause a burn or cut or injury to an unprotected eye. Make certain there is a clear, unobstructed path for safe ejection of these gases and particles. 5. DANGER: If while shooting, your firearm develops ANY mechanical malfunction or binding, or spits powder or gas from the muzzle, or if a cartridge primer is punctured or a cartridge case is bulged or ruptured, or if the report on firing does not sound quite right, STOP SHOOTING IMMEDIATELY. It may be dangerous to continue. UNLOAD THE FIREARM. DO NOT try one more shot. Take the firearm and ammunition to a gunsmith for examination. 6. SAFETY FIRST: While shooting any revolver, a cartridge case may occasionally become jammed against the breech face, impairing the ability of the cylinder to turn freely. Clear the jam as follows, WHILE KEEPING THE MUZZLE POINTED IN A SAFE DIRECTION AND THE FINGERS WELL CLEAR OF THE TRIGGER: push the cylinder release and attempt to open the cylinder. If the cylinder swings open, eject all cartridges and spent cases. Inspect the cartridges and the breech before resuming shooting. DO NOT REUSE THE EJECTED CARTRIDGES
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION
11
Fig.A
Engagement (Secure)
To engage the system, it is necessary to insert the key into the activation pin and turn it clockwise until a click is felt or heard (Fig.B). In this position, the revolvers mechanism is locked and the pin protrudes above the surface of the frame or of the hammer(Fig.1B)
Fig.B
Disengagement (Ready-to-Fire)
To place the revolver in a firing condition, you must insert the key in the security mechanism pin and turn the key counter-clockwise (Fig.C). In this position the top of the pin is in the same plane with the hammer or frame surface (Fig.1C). The revolver is now ready to fire.
Fig.1B
WARNING:
All handguns must be kept out of the reach of children or persons not authorized to use them. Ammunition should be kept separated from the handgun. Never fully rely on any safety or security mechanism. It is not a substitute for safe and cautious gun handling. No safety or security mechanism, however positive or well designed, should be totally trusted. Like all mechanical devices, the safety or security system is subject to breakage or malfunction and can be adversely affected by wear, abuse, dirt, corrosion, incorrect assembly, improper adjustment, repair, or lack of maintenance. Moreover, there is no such thing as a safety which is childproof or which can completely prevent accidental discharge from improper usage, carelessness or horseplay.
Fig.C
Fig.1C
12
REVOLVER OPERATION
The Taurus revolver has a swing out type cylinder with various numbers of chambers, turning around a central axis which allows you to fire (five, six, seven, eight or nine) shots. When the cylinder is locked in position, the revolver is ready for firing. The shots may be fired by single action (by cocking the hammer and thereafter, pulling the trigger) or by double action (by merely pulling the trigger). Concealed hammer models are double action only. Cocking the revolver in both single and double action causes the cylinder to advance, aligning in succession, each of the chambers with the barrel. The cadence of shooting is limited by the shooters skill in loading the cylinder and his ability in operating the gun.
13
Integral Adjustable Sight Models Only The sight blade may be adjusted from left to right only (windage). To adjust, make sure the firearm is unloaded and always keep the muzzle pointed in a safe direction. If possible, leave the cylinder open during adjustment. Locate the adjustment screw on the top of the right side of the frame. Turn the adjustment screw clockwise to move the notch to right side, and counterclockwise to move the notch to left side.
14
Outer Bushing
To adjust the hammer tension, remove the grip by loosening the single screw on the bottom of the grip and pulling it free from the frame. The adjustment knob is in the Frame. Use a small flat bladed screw driver to hold the inner bushing and turn the outer bushing to adjust. Turn clockwise to loosen the tension and counterclockwise to tighten. The tension can be checked by verifying that the firearm is unloaded, pointing the muzzle in a safe direction and dry-firing the revolver. When the hammer tension is adjusted, replace the grip and the grip screw.
Trigger Stop
WARNING: The trigger stop can be extended to a point that prevents the trigger from releasing the hammer to fire the cartridge. This can result in a failure to fire and create a hazardous situation. To adjust the trigger stop, remove the grip by loosening the single screw on the bottom of the grip and pulling it free from the frame. Loosen the trigger stop set screw. Make sure the gun is unloaded, point the muzzle in a safe direction and cock the hammer back. This will bring the trigger to the single-action stop position. Using a needle-nose plier, gently move the trigger stop in or out to the desired position. Allow adequate travel for the trigger to release the hammer and fire the cartridge. Tighten the set screw and replace the grip and grip screw.
Trigger Stop
WARNING: Under no circumstances should you attempt to fire the revolver with the grip removed. Attempting to do so may damage your firearm and may result in accidental death or serious injury.
15
16
9 13 8
15 3 2 1 70 18 17 20 19 22 23 24 33 29 34 45 35 30 28 36 49 48 47 37 51 51 39 38 21 72 32 44 4 71
25 26 27
40
46 50
52
41 42 43
85 85 Ti .38 Special 5
85 UL
650, 850
9 mm PA
2 Barrel 4 5 Total Length 6.8" 8.8 9.8 19 oz. (UL-2) Weight 24 oz. (2) 28.7oz.(4) 31.6 oz.(5) Front Sight Rear Sight Grips Finish BIue or Stainless 27.5 oz. 24 oz. 21 oz. 7.8 6.5 2 2
6.25
6.25
6.25
6.5
6.5
22 oz. 32 oz.
21 oz. 17 oz.
23.6 oz.
21 oz. 16 oz.
17
14
13
12 3 2 1 15 4
63
53
16 18
17
22 21 23
19
20
24
32
51
30
29
44 45
25 26 27 28
31
58
52 41 38 51 39 36 37
34
33 46 35 50
49 48 47 42 40 46 43 50
Barrel
3"
2"
6.75
6.75
18
14 9
13
12
15
4 3 2 1 16
18
17 21 22
20 19 23
24
29 32 44
31 30 25 26 27 51 37 41 39 36 42 52 40 46 43 38 49 28 33 34 35
45
48 47
50
45 LC .41 .40 S&W .410 GA (3) Magnum 5 3 4 6.5 9.5 10.5 12.5 38.8 oz. 38 oz. 41 oz. 5 2" 3" 4" 7" 8" 9" 30 oz. 21 oz. 7.5 2.5 5
Weight
28.2 oz
21.7 oz.
30 oz. 20 oz.
22 oz.
Serrated ramp
19
11 9 14
13
56
12 59
57
15 4 3 2 1 53
54 18
17
55
21 22 24 29 23 30 31
20 19
16
32 44
25 28
26 27
33 34
45
41 51 37 38 40 42 52 43 39 36
35
49 48 47
46
50
5 mm LongColt Remington 5 9
Total Length
11.5
11.5
11.5
8.8
8.8
Weight
45 oz.
34 oz.
45 oz.
45 oz.
38 oz.
38 oz.
Serrated ramp Adjustable Rubber Blue, stainless or titanium (425 and 627 only)
20
10 9 6 5 69 4 3 53 8 2 1 73 74 75 18 17 78 19 22 16 23 21 80 77 76 33 34 45 19 32 35 44 54 15 13 11 56 57
14
24
25 29 26 27 30 28 79 46
51 41 37 39 42 38
50
36
52
43
40
Model Caliber Number of Shots Barrel Total Length Weight Front Sight Rear Sight Grips Finish
992 .22 LR / .22Mag 9 4" 6.5" 11.4" 55 oz Serrated ramp Adjustable Rubber Blue or stainless
21
14 13
4 3 2 1 15 16 15
18
17
20 19
21
22 24 23
51 29 30 31
32
44 45
25 26 27 28
58
33 34 52 41 38 39 51 36 40 42 46 43 50 49 48 47 37 35
36.75 oz. 34.5 oz. Serrated ramp Fixed Rubber Blue or stainless
22
9 14 7
13
15
15
16
54
18
17
55
19
20
21
23
22 24 32
51 44 29 30 31
58
45
33 34 52 38 37 39 51 36
35
41
49
48 47
40
42
46 50
43
Model Caliber Number of Shots Barrel Total Length Weight Front Sight Rear Sight Grips Finish
66
83
86
96
.357 Magnum .38 Special .38 Special .22 Long Rifle 7 4 6 9.75" 12 38 oz. 40.25 oz. 6 6 6 6 11.75 44 oz.
Micrometric click, adjustable for windage and elevation Rubber Blue or stainless
23
11 14
13
8 12
56
57 4 15 3 2
53 16 54 55 18 17 21 20 19 23 51 25 26 27 33 41 52 38 42 58 40 43
51
32 24 22 29 30 44 45 31 28
35
34 37
39 36
49 48 47
46 50
Serrated ramp
24
14
9 13
56
12
57
4 3 2 1
15
53 54
16
55 18 17 21 20 19 22 24 44 32 45 29 30 25 33 31 26 27 41 39 36 52 40 42 28 37 38 49 48 47 34 35
51
23
43 46 50
Number of Shots
Barrel
Total Length
Weight
2.25" 5 6.5 8.4 7.5 12 12 8 10.5" 14" 14" 9.75" 12 14 48 oz. 53 oz. 54 oz. 27.3 oz. 51 oz. 63 oz. 63 oz. 28.3 oz. 53 oz. 63 oz. Patridge style or fixed with fiber optic (444 UL/Ti only) 6.5 8.4" 6.5 8.4" 2.25 4" Micrometric click, adjustable for windage and elevation or fixed. (444 UL/Ti only) Rubber Blue or Stainless
3" 6.5"
3" 6.5"
10.2 13.6"
10.2 13.6"
62 oz. 73 oz.
25
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
EXTRACTOR CYLINDER RETAINING BUSHING CENTER PIN CENTER PIN SPRING EXTRACTOR SPRING EXTRACTOR ROD COLLAR EXTRACTOR ROD SPRING CYLINDER YOKE FRONT LATCH FRONT LATCH SPRING CYLINDER STOP PLUNGER WITH SPRING FRONT LATCH PIN EXTRACTOR ROD BARREL FRAME THUMB PIECE THUMB PIECE SCREW FIRING PIN FIRING PIN SPRING FIRING PIN RETAINING PIN BOLT BOLT SPRING HAMMER ASSEMBLY KEYLOCK KEYLOCK SPRING KEYLOCK BALL KEYLOCK PIN SEAR SEAR SPRING SEAR PIN TRANSFER BAR HAND SPRING HAND PIN TRIGGER ASSEMBLY TRIGGER SPRING ASSY TRIGGER SPRING CENTER PIN
38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 60 61 63 69 70 71 72 73 74 75 76 77 78 79 80
TRIGGER SPRING TRIGGER SPRING SWIVEL MAIN SPRING ASSEMBLY MAIN SPRING CENTER PIN MAIN SPRING MAIN SPRING PLATE CYLINDER STOP HAND SIDE PLATE YOKE SCREW YOKE RETAINING PIN SPRING YOKE RETAINING PIN SIDE PLATE SCREW RUBBER GRIP GRIP SCREW REAR SIGHT ASSEMBLY REAR SIGHT SPRING REAR SIGHT PIN FRONT SIGHT FRONT SIGHT PIN STOCK PIN FIRING PIN BUSHING CENTER PIN BUSHING REAR SIGHT SCREW CYLINDER DISTANCE BUSHING STELLAR CLIP BARREL RETAINING PIN YOKE BLOCKING PIN CYLINDER ASSY CATCH LOCK CYLINDER ASSY CATCH SPRING CYLINDER ASSY CATCH CYLINDER STOP SPRING CYLINDER STOP SPRING CYLINDER STOP SPRING PIN SIDE PLATE SCREW FRONT CYLINDER STOP SPRING BUSHING PIN
26
TAURUS NEWS
If you desire to receive periodic e-mails relating to new products from us, you may utilize our product enrollment web page at http://www.taurususa.com/product-enrollment.cfm Privacy Statement We do not share, sell or reveal customer information. This information is for our records only. Your e-mail address and purchase information will be kept confidential.
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION
27
28
PARTS
All firearms require periodic maintenance and inspection which may reveal a need for adjustment or repair. Have your firearm checked by a competent gunsmith annually, even if it seems to be working well, since breakage, improper functioning, undue wear, or corrosion of some components may not be apparent from external examination. If you notice ANY mechanical malfunction, do NOT continue to use the firearm. UNLOAD the firearm and take it to a competent gunsmith immediately. Our Service Department maintains a full complement of replacement parts for our firearms of current manufacture. Even though most gunsmiths have the knowledge, training and ability to make the necessary repairs to your firearm, the skill and workmanship of any particular gunsmith is totally beyond our control. Should your firearm ever require service, we strongly recommend that you return it to Taurus. Follow the instructions outlined below. Remember, unauthorized adjustments or parts replacement can void your warranty. It is the responsibility of the purchaser to be absolutely certain that any parts ordered from Taurus are of the correct type and are properly fitted and installed by a competent person. THIS FIREARM IS A PRECISION MECHANISM AND THE IMPROPER FITTING OF PARTS OR IMPROPER MECHANICAL ADJUSTMENT MAY RESULT IN A DANGEROUS MALFUNCTION, DAMAGE TO THE FIREARM, AND POSSIBLE SERIOUS INJURY TO THE SHOOTER OR TO OTHERS. Therefore, the purchaser and/or installer of parts must accept full responsibility for the correct adjustment of and function of the firearm after such installation has been made or attempted.
Notice:
It is recommended that you record the model number, serial number and date of purchase of your Taurus firearm for future reference. Be sure to retain your store receipt and any other documentation that came with your Taurus. Model Number _______________________________ Serial Number ________________________________ Date of Purchase______________________________
29
NOTES
30
This trademark, forged for over 70 years of hard and dedicated work, became a symbol of quality in handguns for civilian, police and military use. This outstanding quality is the result of constant technological evolution and from the devoted work of expert gunsmiths and highly specialized professionals, which makes TAURUS a respected name in more than 75 countries all over the world
IMPORTANT
DO NOT DISCARD
KEEP THIS MANUAL WITH YOUR FIREARM UPON CHANGE OF OWNERSHIP.
FORJAS TAURUS S.A. Avenida do Forte, 511 CEP: 91.360-000 Porto Alegre - RS - Brasil Fone: 55-51-30213000 Fax: 55-51-30213110 TAURUS INTERNATIONAL MANUFACTURING, INC. 16175 NW 49 Avenue Miami, Florida 33014 Telephone: (305) 624 1115 Fax: (305) 624 1126
www.taurususa.com www.taurus.com.br
BR
CERT