A7 Amps Manual - Compressed PDF
A7 Amps Manual - Compressed PDF
A7 Amps Manual - Compressed PDF
A775.4
A7125.4
A7300.2
A7750.1
A71100.1
A71500.1
A72000.1
A72500.1
User Manual
• Instalation Instructions / Owners Manual •
Due to continuous improvement of the product the Specifications are subject to change without notice.
OKUR
1. OKUR AMPLIFIER’S SPECIFICATION
2
2-2. OKUR 2 and 4channel class AB amplifiers
INPUT OUTPUTS
Connect the RCA output cables from the headunit Is used when connecting multiple amplifer to the same
to OKUR amplifiers’ RCA Input. RCA signal
3. INSTALLATION
In case you install the OKUR amplifiers by yourself, please read owner's manual
very carefully.
Before you start your installation, please take all steps into consideration.
or, you can have DB Drive or DB Reseach’s authorized dealer to check installation and set
your car audio systems.
3
3-1. MOUNTING PREPARATION
Disconnect the negative ( ) battery cable before mounting your OKUR amplifier or making any connections.
Check the battery and alternator ground ( ) connections.
Make sure they are properly connected and Free of corrosion before selecting a mounting location.
Please take some concerns into consideration with cooling efficiency and safety.
The OKUR amplifier uses a specially designed heat radiation heatsink to avoiding excessive heat from
OKUR circuitry.
But for better heat disipitation, It is good to find the mounting location where you can install
OKUR vertically with the heatsink fins and better air flow around heat sink.
For the safety, you have to find dry and well ventilated location and make sure any cables
and drilling car equipment are not interfaced with mounting location.
Be sure the mounting location and drilling of pilot cables will not present a hazard to any cables,
control cables, fuel lines, Fuel tanks, hydraulic lines or other vehicle systems or components.
Before mounting Platinum series, disconnect the negative ( ) wire from battery to protect
any accidentIal damage to amplifier and audio system.
A775.4 , A7125.4, A7300.2 ,A7750.1 ,A71100.1 and A71500.1 are designed to use minimum 4 gauge power
and ground cables A72000.1, A72500.1, are designed to use minimum 0 gauge cables.
Run a remote turn on cable from the head units remote switched + 12V output.
4
OKUR +12V, GROUND, REMOTE CONNECTION DIAGRAM
Remote turn on
Ground
12V
BATTERY
CAUTION !!
A7750.1, A71100.1, A71500.1, A72000.1,
A72500.1 amplifiers
minimum impedance is 1 ohms. 8~ 1 ohms
8~ 2 ohms
8~ 2 ohms
8 ~ 2 ohms 8 ~ 2 ohms
8 ~ 2 ohms 8 ~ 2 ohms
CAUTION !!
A7300.2, A775.4 & A7125.4 Amplifiers’ minimum impedance is
2 ohms stereo or 4 ohm mono
6
OKUR 4CHANNEL AMPLIFIERS’ SPEAKER CONNECTION DIAGRAM 2.
8 ~ 2 ohms
8 ~ 2 ohms
8~ 4 ohms
8 ~ 2 ohms 8 ~ 2 ohms
8 ~ 2 ohms 8 ~ 2 ohms
8~ 4 ohms
7
3-5. OKUR DIGITAL AMPLIFIER’S MULTI-LINKING CONNECTION
Step 1. Connect the master amplifier to the head-unit and set its output master and input slave switch
to output master position.
Step 2. Connect the master and slave amplifiers in daisy chain Rca jack as shown in the diagram.
Step 3. Set slave amplifier output master & input slave switch to slave input position.
Step 4. Connect speaker cable ( + ) on master amplifier to subwoofer ( + )
Step 5. Connect speaker cable ( + ) on slave amplifier to subwoofer ( )
Step 6. Connect speaker cable ( ) on master amplifier to speaker cable ( ) on slave amplifier
Headunit
R L
MASTER AMPLIFIER
SLAVE AMPLIFIER
CAUTION !!
A7750.1, A71100.1, A71500.1, A72000.1 & A72500.1 Amplifiers’
Linked minimum impedance is 2 ohms.
8
Remote turn on
MASTER AMPLIFIER
Ground
12V 8 ~ 2 ohms
BATTERY
SLAVE AMPLIFIER
Ground
CAUTION !!
A7750.1, A71100.1, A71500.1, A72000.1, & A72500.1 Amplifiers’
Linked minimum impedance is 2 ohms.
9
4. TROUBLE SHOOTING
NO SOUND ( NO OUTPUT )
1) Please check all connections, cables' rounting, short and voltage at OKUR amplifiers
and headunit
2) Please check built-in or external fuses ,If it is brlown, pls replace with new one.
3) Please check whether speakers work well, you can test speakers by connecting to another amplifier
PROTECTION
WHINING NOISE
10
LIMITED WARRANTY
DB Research L.L.P.
302 Hanmore Industrial Parkway // Harlingen, TX 78550
® ph: 877.787.0101 // www.dbdrive.net