Technical Data Sheet

Approved 25740;25980 1,5 25740 epoxy VValidationDate). 1

Jotafloor EP SL

Product description
This is a two component solvent free amine cured epoxy coating. It is a high performance product. It is a self
levelling product leaving a seamless surface. It is flexible, abrasion, impact, chemical and slip resistant. If slip
resistance is required Jotafloor Non Slip can be used in the system. To be used as midcoat/topcoat as part of a
complete system in atmospheric environments. Suitable on approved primers on concrete substrates.

Typical use
Suitable for a wide range of floors with various levels of mechanical and chemical exposure. Specially designed
for industrial floors, laboratories, hospitals, food and beverage plants, kitchens, high tech manufacturing
facilities, dairies, warehouses, factories and hangars. May be used as a scrape coat to cover minor undulations
on the surface.
Other

Approvals and certificates

Determination of Compressive Strength - ASTM C579
Determination of Tensile Strength - ASTM C307
Determination of Flexural Strength - ASTM C580
Determination of Bond strength to host concrete - BS 1881 : Part 207
Determination of Crack Bridgeability - ASTM C884
Determination of Rapid Chloride Permeability - AASHTO T277
Determination of Water Permeability - DIN 1048
Determination of Acid or Alkali Reaction - ASTM D543
Determination of Water or Salt Spray Test - N.F.C. Standard
Determination of Impact Resistance - ISO 6272
Determination of Shore 'A' hardness - ASTM D2240
Determination of Taber Abrasion (1,000 Cycles) - ASTM D4060
Determination of Toxicity - BS 6920
Determination of Flame Spread - ASTM D1360
Determination of resistance to aviation fuel - ASTM D543 : 1987
Determination of ease of decontamination - BS4247 Part 1:1987
Determination of resistance to skydrol hydraulic fluid - ASTM D543-1987
Additional certificates and approvals may be available on request.

Colours
selected range of colours

Product data
Property Test/Standard Description
Solids by volume ISO 3233 98 ± 2 %
Gloss level (60 °) ISO 2813 gloss (70-85)
Flash point ISO 3679 Method 1 100 °C
VOC-USA / VOC Hong Kong EPA Method 24 67 g/l
VOC-Solvent Emission Directive SED (1999/13/EC) 50 g/kg

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss level: According to Jotun Performance Coatings' definition.

Date of issue: 15 December 2014 Page: 1/4

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor EP SL

Recommended film thickness per coat

Film thickness and Dry film thickness Wet film thickness Theoretical
spreading rate spreading rate
(μm) (μm) (m²/l)

Minimum 800 800 1,25

Maximum 5000 5000 0,2
Typical 2000 2000 0,5

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating (ISO 12944-4 6.1) coating (ISO 12944-4 6.1)

Application
Application methods
The product can be applied by

Trowel: Recommended

To avoid air bubbles, it is very important to pierce the coating with a spiked roller when desired film thickness is
achieved.

Product mixing ratio (by volume)

Jotafloor EP SL Comp A 4,7 part(s)

Jotafloor EP SL Comp B 1 part(s)

Thinner/Cleaning solvent
Cleaning solvent: Jotun Thinner No. 17

Date of issue: 15 December 2014 Page: 2/4

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor EP SL

Drying and Curing time

Substrate temperature 15 °C 23 °C 40 °C

Surface (touch) dry 8h 5h 2h

Walk-on-dry 32 h 20 h 8h
Dry to over coat, minimum 32 h 20 h 8h
Dried to over coat, maximum, atmospheric 96 h 48 h 36 h
Dried/cured for service 12 d 9d 3d

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the
surface.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried to over coat, maximum, atmospheric: The longest time allowed before the next coat can be applied
without any surface preparation.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Pot life 20 min

45 min. after poured on to the floor.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: epoxy

Subsequent coat: epoxy, polyurethane

Packaging (typical)
Volume Size of containers
(litres) (litres)

Jotafloor EP SL Comp A 14 20
Jotafloor EP SL Comp B 3 3

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Date of issue: 15 December 2014 Page: 3/4

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor EP SL

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Jotafloor EP SL Comp A 12 month(s)
Jotafloor EP SL Comp B 24 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
Products primarily meant for use as primers and antifoulings may have slight color variations from batch to
batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 15 December 2014 Page: 4/4

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com