Sist en 16722 2015

SLOVENSKI STANDARD
SIST EN 16722:2015
01-december-2015
,QGXVWULMVNLYHQWLOL9JUDGQHGROåLQH]DYHQWLOH]YLMDþQLPL]DNOMXþNL
Industrial valves - End-to-end and centre-to-end dimensions for valves with screwed
ends
Industriearmaturen - Baulängen für Armaturen mit Innengewinde-Anschluss
iTeh STANDARD PREVIEW

Robinetterie industrielle - Dimensions extrémité à extrémité et axe à extrémité pour les
(standards.iteh.ai)
appareils de robinetterie à embouts taraudés
SIST EN 16722:2015
Ta slovenski standard je istoveten z: EN 16722:2015
https://standards.iteh.ai/catalog/standards/sist/0b90739a-6169-48e1-a085-
3babe0c5a156/sist-en-16722-2015
ICS:
23.060.01 Ventili na splošno Valves in general
SIST EN 16722:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 16722:2015

(standards.iteh.ai)
SIST EN 16722:2015
3babe0c5a156/sist-en-16722-2015
SIST EN 16722:2015
EUROPEAN STANDARD EN 16722

NORME EUROPÉENNE
EUROPÄISCHE NORM September 2015
ICS 23.060.01
English Version
Industrial valves - End-to-end and centre-to-end

dimensions for valves with threaded ends
Robinetterie industrielle - Dimensions extrémité à Industriearmaturen - Baulängen für Armaturen mit
extrémité et axe à extrémité pour les appareils de Innengewinde-Anschluss
robinetterie à embouts filetés
This European Standard was approved by CEN on 15 August 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
(standards.iteh.ai)
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
SIST EN 16722:2015
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom. https://standards.iteh.ai/catalog/standards/sist/0b90739a-6169-48e1-a085-
3babe0c5a156/sist-en-16722-2015
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16722:2015 E
worldwide for CEN national Members.
SIST EN 16722:2015
EN 16722:2015 (E)
Contents Page
European foreword....................................................................................................................................................... 3
Introduction .................................................................................................................................................................... 4
1 Scope .................................................................................................................................................................... 5
2 Normative references .................................................................................................................................... 5
3 Terms and definitions ................................................................................................................................... 5
4 Dimensions and tolerances ......................................................................................................................... 6
4.1 Basic series ........................................................................................................................................................ 6
4.2 Tolerances ......................................................................................................................................................... 7
Annex A (informative) Relationship between DN (nominal size) and internal thread .................. 16
Annex B (informative) Origin of basic series .................................................................................................. 17
Annex C (informative) Relationship between DN (nominal size) and nominal pipe size
(NPS) ................................................................................................................................................................. 18
Bibliography ................................................................................................................................................................. 19
(standards.iteh.ai)
SIST EN 16722:2015
3babe0c5a156/sist-en-16722-2015
2
SIST EN 16722:2015
EN 16722:2015 (E)
European foreword
This document (EN 16722:2015) has been prepared by Technical Committee CEN/TC 69 “Industrial
valves”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall
be withdrawn at the latest by March 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

(standards.iteh.ai)
SIST EN 16722:2015
3babe0c5a156/sist-en-16722-2015
3
SIST EN 16722:2015
EN 16722:2015 (E)
Introduction
The basic series given in this European Standard are taken from the original series shown in Annex B.
Changes made to the original series will not be automatically incorporated into this European Standard.

(standards.iteh.ai)
SIST EN 16722:2015
3babe0c5a156/sist-en-16722-2015
4
SIST EN 16722:2015
EN 16722:2015 (E)
1 Scope
This European Standard specifies the end-to-end and centre-to-end dimensions for valves with
threaded ends with connecting dimensions in compliance with EN ISO 228-1 or EN 10226-1, used in PN
and Class designated piping systems.
The range of PN is:
— PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400.
The range of Class is:

— Class 150, Class 300, Class 600, Class 900, Class 1 500, Class 2 500.
The range of nominal size is:

— DN 4; DN 6; DN 8; DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100.
NOTE 1 See Annex C for the relationship between nominal size (DN) and nominal pipe size (NPS).
NOTE 2 Valves having screwed end profiles different from those specified in EN ISO 228-1 or EN 10226–1, may
use the same dimensions than those specified in Table 1.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
(standards.iteh.ai)
references, the latest edition of the referenced document (including any amendments) applies.
EN 736-1:1995, Valves — Terminology — Part
SIST EN1:16722:2015
Definition of types of valves
EN 736-2:1997, Valves — Terminology — Part 2: Definition of components of valves
3babe0c5a156/sist-en-16722-2015
EN 736-3:2008, Valves — Terminology — Part 3: Definition of terms
3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 736-1:1995, EN 736-2:1997
and EN 736-3:2008 and the following apply.
3.1
end-to-end dimensions (ETE)
(straight pattern valves)
distance expressed between the ends of the body for straight and oblique pattern valves
3.2
centre-to-end dimensions (CTE)
(angle pattern valves)
distance expressed between one of the ends of the body and the centre of the body for angle pattern
valves
3.3
end-to-end and centre-to-end dimensions (ETE+CTE)
(three-way valves)
distance expressed between the ends of the body (ETE) in the run and distance expressed between the
end of the body in the branch and the centre of the body (CTE)
5
SIST EN 16722:2015
EN 16722:2015 (E)
a) Straight and oblique pattern valve
b) Angle pattern valve

(standards.iteh.ai)
SIST EN 16722:2015
3babe0c5a156/sist-en-16722-2015
c) Three-way valve
Key
Figure 1 a) ETE with ETE = l
Figure 1 b) CTE with CTE = l
Figure 1 c) ETE+CTE with ETE = l and CTE = l / 2
Figure 1 — ETE and CTE dimensions
4 Dimensions and tolerances

4.1 Basic series
The basic series of l for ETE and CTE dimensions are given in Table 1.
For each type of valve, the basic series to be taken into consideration shall be in accordance with
Tables 3 to 7.
Other dimensions are subject of agreement between manufacturer and purchaser.
6
SIST EN 16722:2015
EN 16722:2015 (E)
NOTE 1 Table 1 gives complete series. In Tables 3 to 7 the columns of series may be reduced.
NOTE 2 For certain sizes/types of valves, alternative dimensions are permitted and are specified in Tables 3 to
7.
4.2 Tolerances
Tolerances on ETE and CTE dimensions shall be in accordance with Table 2.

(standards.iteh.ai)
SIST EN 16722:2015
3babe0c5a156/sist-en-16722-2015
7
SIST EN 16722:2015
EN 16722:2015 (E)
Table 1 — Dimensions l of basic series

Dimensions in millimetres
Basic series
DN
M2 M3 M4 M5 X1 X2 X3 X4 X5 X6 X7 X8 X9 X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X20
4 – 50 70 50 – – – – – – – – – 69 69 69 – – – – – – – –
6 – 50 70 50 – – – – – – – – – 69 69 69 – 85 – – – – – –
8 – 55 70 55 – – – 70 65 78 – – – 69 69 – – 85 – – – 55 67 75
10 70 60 75 55 95 – – 70 65 78 55 – – 73 73 72 – 85 – – – 55 67 75
15 85 75 85 65 95 49 200 70 65 90 65 117 104 84 – – – – 95 – – 65 75 90
20 100 80 95 75 95 49 200 80 65 95 80 117 104 96 97 95 – 100 95 – – 70 90 105
25 115 90 105 90 95 61 200 iTeh STANDARD PREVIEW

90 – – – 139 104 113 113 113 120 110 95 65 80 85 105 120
32 130 110 120 95 95 61 200 –

(standards.iteh.ai)
– – – 186 – 110 115 110 120 130 – 65 80 95 120 –
40 150 120 130 100 130 72 255 – – – – 186 – 120 135 130 140 145 165 70 87 105 135 –
50 180 140 150 112 230 72 255 – – – SIST–EN 16722:2015

209 – 140 140 140 150 160 165 70 91 125 155 –
65 – 185 185 132 – – – – – 3babe0c5a156/sist-en-16722-2015
– – – – – – – – – – – – 167 190 –
80 – 205 205 160 – – – – – – – – – – – – – – – – – 192 205 –
100 – 240 240 180 – – – – – – – – – – – – – – – – – – 230 –
8
SIST EN 16722:2015
EN 16722:2015 (E)
Table 1 (continued)
Dimensions in millimetres
Basic series
DN
X21 X22 X23 X24 X25 X26 X27 X28 X29 X30
4 – – – – – – – – – –
6 – – – – – – – – – –
8 70 72 – – 42 – – – – –
10 70 72 – 75 49 60 59 83 – 105
15 75 82 75 85 56 65 74 90 90 114
20 iTeh
85 92 STANDARD
75 100 61 78 PREVIEW
80 97 100 125
25 102 102 (standards.iteh.ai)
75 115 69 92 91 110 115 142
32 118 118 – 130 77 105 110 124 134 160
40 125 134 – SIST EN
150 8116722:2015
120 120 130 150 170
50 149 144 –3babe0c5a156/sist-en-16722-2015
180 95 145 141 155 168 200
65 – – – 170 112 – – – – –
80 – – – 220 122 – – – – –
100 – – – – 160 – – – – –

Sist en 16722 2015

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Sist en 16722 2015

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sist en 16722 2015

Uploaded by

Copyright:

Available Formats

SLOVENSKI STANDARD

Industriearmaturen - Baulängen für Armaturen mit Innengewinde-Anschluss

iTeh STANDARD PREVIEW