Lloyds Approved Mills

List 1
Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars
This list identifies works approved by Lloyd’s Register Group Limited (LR) for steelmaking
and the manufacture of rolled steel plate, strip, sections and bars in accordance with the
requirements of LR's Rules for the Manufacture, Testing and Certification of Materials,
Chapter 3.
The information listed for each works is a summary of the product, generic grade and
maximum thickness, or in the case of round bars, diameter approved.
It is important to note that this list does not provide full details of the grades approved by
LR as required by the Rules. The combinations of deoxidation practice (e.g. killed,
semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V,
etc.), in association with specific rolling procedures ( e.g. N or TM, etc.), are not included.
These parameters may vary within each grade by manufacturer and could influence the
fabrication procedures that can be applied.
The list also includes firms approved for the manufacture of fabricated steel sections.
Where required this information should be obtained from the current certificate of approval
issued to the manufacturer by LR.
Works designated "MQS Approved" are also approved under the Materials Quality Scheme
in accordance with LR's Rules for the Manufacture, Testing and Certification of Materials,
Chapter 1 Section 2.
Approval only covers the manufacturing location listed, it does not extend to other works
owned by the same company. The local LR surveying office is also listed.
Abbreviations:
B.O.S. Basic Oxygen Steelmaking

Con Cast Continuous Casting
E.A.F. Electric Arc Furnace
O.H. Open Hearth
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers,
employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's
Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person for
any loss, damage or expense caused by reliance on the information or advice in this
document or howsoever provided, unless that person has signed a contract with the
relevant Lloyd's Register entity for the provision of this information or advice and in that
case any responsibility or liability is exclusively on the terms and conditions set out in that
contract.
As at 13 May 2014
This is a copy of an electronic document. In the event of any conflict or ambiguity between the copy and the electronic document,
which is retained and published by Lloyd's Register, the original electronic and certified version shall always prevail.
© Lloyd’s Register Group Limited 2014. All rights reserved.
List 1
Name and Address LR Office Product Category Grade Max Thickness/Diameter (mm)
Argentina
ACEROS ANGELETTI S.A. Buenos Aires Steelmaking E.A.F. / Ingot carbon, carbon-manganese 30
Semi-Finished Ingots (tonnes) carbon, carbon-manganese 30
Burzaco
Av. Hipolito Yrigoyen 16102/96
(1852)-Burzaco
Pcia. de Buenos Aires
Tel No: +54 11 4299 0110 Fax no: +54 11 4299 0110
Email:ventas@acerosangeletti.com.ar
Web: www.acerosangeletti.com.ar
Certificate No. MD00/3676/ 0002/ 1 Expiry date 22/02/2015
Australia
BLUESCOPE STEEL (AIS) PTY. LTD. Sydney Steelmaking B.O.S. / Con Cast As below
Plates Normal Strength A, B, D, E 51
Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36, 51
EH27S, EH32, EH36
Hot Rolled Coil Normal Strength A, B, D, E 13
EH27S, EH32, EH36
Port Kembla Steelworks
P.O. Box 1854
Wollongong
NSW 2500
Tel: +61 2 42754666 Fax: +61 2 42753045 Email: mailto:nigel.attwell@bluescopesteel.com
Plates with specified through thickness properties notation Z35 may be added.
Normalizing heat treatments carried out by sub-contractor, Bisalloy.
Certificate # MD00/1929/0008/1 Expiry date: 20/07/2015
Austria
BREITENFELD EDELSTAHL AG Vienna Steelmaking E.A.F./V.O.D./Ingot As below
Semi-Finished Ingots (tonnes) carbon, carbon-manganese, alloy, austenitic 120
stainless, duplex stainless
Breitenfeldstrasse 22
A-8662 Mitterdorf im Mürztal
Tel: +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248
Email mailto:marina.paller@breitenfeld.at
Web: http://www.breitenfeld.at
Certificate # MD00/3255/0004/1 Expiry Date: 07/06/2015
Including VD/VOD
BÖHLER EDELSTAHL GmbH Vienna Steelmaking E.A.F./Ingot/Con Cast As below
Bars Structural carbon, carbon-manganese, alloy, austenitic 220
Mariazellerstraße 25
Postfach 96
A-8605 Kapfenberg
Tel: +43 3862 20 37063 Fax: +43 3862 20 37559 Email: mailto:walter.wolflehner@bohler-edelstahl.at Web:http://www.bohler-edelstahl.com
Certificate #: MD00/0200/0007/1 Expiry date: 22/01/2015
BÖHLER YBBSTAL PROFIL GmbH Vienna Sections Normal Strength A, B, D, E 20
Higher Strength AH32, AH36, DH32, DH36, EH32, EH36 20
Bars Normal Strength A, B, D, E 20
Structural carbon, carbon-manganese, alloy, austenitic 20
Waidhofnerstraße 8
3333 Böhlerwerk
Tel: +43 7448 7007 504 Fax: +43 7448 7007 250 Email: mailto:herwig.kohlreiter@bohler-profil.com Web:http://www.bohler-profil.com
High alloy bars and sections may be accepted for approved applications.
SONDERSTAHLWERK BREITENFELD GmbH Vienna Steelmaking VAR/INGOT As below 38
ESR Ingots carbon, carbon-manganese, alloy, austenitic 38
stainless, duplex
Breitenfeldgasse 23
A-8661 Wartberg
Tel +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248
Email marina.paller@breitenfeld.at Web http://www.breitenfeld.at
Including remelting of Ni materials
Page 2 As at 13 May 2014

List 1
STAHL JUDENBURG GmbH Vienna Bars Normal Strength A 120

Structural carbon, carbon-manganese 120
Machinery carbon, carbon-manganese, carbon-manganese 120
Gußstahlwerkstrasse 21
A-8750 Judenburg
Tel: +43 3572 701-358 Fax: +43 3572 701-248 Email: mailto:christian.sunnitsch@stj.at Web: http://www.stahl-judenburg.com
VOESTALPINE GROBBLECH GmbH Vienna Steelmaking B.O.S. / Con Cast As below
Higher Strength AH42, DH42, EH42 55
AH40, DH40, EH40, FH40 100
AH32, AH36, DH32, DH36, EH32, EH36, FH32, 140
FH36
Boiler & Pressure Vessel 360AR 40
410AR 50
360FG, 410FG, 460FG, 490FG, 510FG 140
Ferritic Low Temperature 1.5Ni, 3.5Ni, 5Ni, 9Ni 50
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32, 140
LTEH36, LTFH32, LTFH36
Clad D/304L 50
P.O Box 3
Voest.- Alpine - Str. 3
A-4020 Linz
Tel: +43 50304 15 9091 Fax: +43 50304 55 9091
Email: mailto:ronald.lachmair@voestalpine.com Web: www.voestalpine.com
Certifcate No. MD00/1614/0008/1 Expiry date: 30/07/2014
Approval includes the supply of z25 and z35 grades.
Approval includes pressed heads.

VOESTALPINE STAHL DONAWITZ GmbH & Co Vienna Steelmaking B.O.S. / Con Cast carbon, carbon-manganese, alloy
KG
Semi-Finished Blooms/Billets carbon, carbon-manganese, alloy 285
Kerpelystraße 199
A 8700 Leoben
Tel: +43 50304 25-4659 Fax: +43 50304 65-2464 Email: mailto:karin.rockenschaub@voestalpine.com Web:http://www.voestalpine.com/stahldonawitz
Belarus, Republic of
OJSC "Byelorussian Steel Works-Management St. Petersburg Steelmaking E.A.F./V.O.D./Con Cast As below
Company of
Semi-Finished Rolled Billets Carbon, Carbon-Manganese 140
Billets carbon, carbon-manganese, Normal Strength 300
"Byelorussian Metallurgical Company" holding"

(OJSC "BSW -management company of "BMC" holding")
37, Promyshlennaya Str.
BY- 247210 Zhlobin,
Gomel Region,
Tel No: +375 2334 56180 Fax no: +375 2334 56317 Mob +375 291105030
Email : mailo:nb.ouk@bmz.gomel.by
Web: xxxxxxxxxxxxxxxx
Certificate No: MD00/4297/0001/1 Expiry date 05/03/2017

List 1
Belgium
APERAM Genk Antwerp Steelmaking E.A.F./A.O.D./Con Cast austenitic stainless
B.O.S/V.O.D./Con Cast austenitic stainless
Semi-Finished Slabs austenitic stainless 200
Plates Austenitic Stainless 304L, 304LN, 316L, 316LN, 317L, 317LN, 321, 14
347
Swinnenwijerweg 5
Genk - Zuid, Zone 6A
B-3600 Genk
Tel: +32 89 30 25 68 Fax: +32 89 30 25 53 Email: stefaan.maes@arcelormittal.com
ESB sprl Antwerp Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms carbon, carbon-manganese, alloy, Ferritic 600
Stainless Steel*
ENGINEERING STEEL BELGIUM
Rue de l'Environnement, 8
B - 4100
Seraing
Tel No: +32 4 33 885 60 Fax No: +32 4 33 809 00
Email : dtroisfontaines@esb.be
Web : www.esb.be
Certificate No: MD00/3858/0002/1 Expiry date: 09/11/2016
Materials Suitable for Steel Forgings, Pipe and Tube, Ingots up to 800mm diameter and Blooms up to 600 mm diameter
INDUSTEEL BELGIUM SA Antwerp Steelmaking E.A.F. / Con Cast As below
Higher Strength AH32, AH36, DH32, DH36, EH32, EH36, EH40 50
DH42, DH46, DH50, DH55, DH62, DH69, EH42, 100
EH46, EH50, EH55, EH62, EH69, FH42, FH46,
FH50, FH55, FH62, FH69
Boiler & Pressure Vessel 360AR, 410AR 40
360FG, 410FG, 460FG, 490FG, 510FG 50
Ferritic Low Temperature LTAH32, LTAH36, LTDH32, LTDH36, LTEH32, 50
LTEH36, 5Ni, 9Ni
Austenitic Stainless 304L, 304LN, 316L, 316LN 50
Duplex Stainless UNS S31803(MOD)* 40
ARCELOR MITTAL GROUP
266, Rue de Châtelet
B-6030 Charleroi
Tel: +32 71 44 14 51 Fax: +32 71 44 19 29 Email: mailto:patrick.malgre@arcelormittal.com Web: http://www.arcelormittal.com
Plates in grades LTAH32; LTAH36; LTDH32; LTDH36; LTEH32; LTEH36; 5%Ni; 9%Ni over 40mm thickness and up to the maximum thickness stated above are
accepted for approved applications only.
* accepted for approved applications.
Higher strength grades supplied in the quenched and tempered grades are accepted with specified through thickness properties designation Z35.
Certificate Number: MD00/0477/0009/1 Expiry: 09/07/2014
NLMK CLABECQ S.A. Antwerp Plates Normal Strength A, B, D, E 120
EH27S, EH32, EH36
360, 410 50
360FG, 410FG, 460FG, 490FG, 510FG 120
Rue de Clabecq, 101
B-1460 Ittre
Tel: +32 (0) 2 3919227 Fax: +32 (0)2 3919883
Email:j.vermeulen@eu.nlmk.com
Web:http://www.eu.nlmk.com
MQS Approved - Approval No. MQS016
Certificate #: MD00/2204/0011/1 Expiry date: 24.06.2015

List 1
Brazil
ARCELORMITTAL BRAZIL S/A Rio de Janeiro Steelmaking B.O.S. / Con Cast carbon, carbon-manganese
(ARCELORMITTAL TUBARÃO )
Semi-Finished Slabs carbon, carbon-manganese 250
Hot Rolled Coil Normal Strength D 16
A, B 19
Higher Strength AH27S, AH32 16
Boiler & Pressure Vessel 460FG, 490FG 16
360FG, 410FG 19
Av. Brigadeiro Eduardo Gomes

930 - Jardim Limoeiro
29164-970 Serra/ES
Carbon and carbon-manganese grades cover the following LR normal and higher tensile strength grades. A, B, D, E, AH27S, AH32, AH36, DH27S, DH32,
DH36, EH27S, EH32, EH36
Tel: +55 27 3348 3261 Fax: +55 27 3348 2211
Email : mailto:adelson.nascimento@arcelormittal.com
Web: http://www.arcelormittal.com/br/
GERDAU AÇOMINAS S.A. Rio de Janeiro Steelmaking B.O.S./Ingot/Con Cast As below
Semi-Finished Rolled Billets Carbon, Carbon-Manganese, Alloy 180
Slabs carbon, carbon-manganese, alloy 250
Blooms carbon, carbon-manganese, alloy 300
Billets carbon, carbon-manganese, alloy 180
Rolled Slabs Carbon, Carbon-Manganese, Alloy 450
Rolled Blooms Carbon, Carbon-Manganese, Alloy 900
Rodovia MG-443 KM 7
Fazenda do Cadete
36420-000-Ouro Branco-MG
Tel: +55 3137 493471 Fax: +55 3137 3215 Email: mailto:isaac.soares@gerdau.com.br web http://www.gerdau.com.br
Slabs and blooms intended for plates and forgings
GERDAU S/A São Paulo Steelmaking E.A.F. / Ingot As below
Bars Machinery carbon, carbon-manganese 125
Chain Cable Stock R3 117
U1, U2, U3 125
Pindamonhagaba Plant
Rod.Luiz Dumont Villares km 2- Moreira César
CEP 12442-260
Pindamonhangaba S.P.
Tel: +55 12 2126 7174 Fax: +55 12 2126 7325 Email: mailto:fernando.almeida@gerdau.com.br Web:http://www.gerdau.com.br
Bars for grade R3 chain cable is restricted to supply to Companhia Brasileira Amarras with specification EC-Gr.3a.
Ingots as semi-finished products to the above maximum weight nominal 630mm x 530mm x 2150mm long are accepted for further processing for rolled
products.
USIMINAS Rio de Janeiro Steelmaking B.O.S. / Con Cast As below
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 50
Hot Rolled Coil Normal Strength A 12
Boiler & Pressure Vessel 360, 410 12
Usinas Siderúrgicas de Minas Gerais S/A
Usina Intendente Câmera
Av. Pedro Linhares Gomes, 5431
Distrito Usiminas, CEP 35160-900
Ipatinga, Minas Gerais
Tel +55 (0)31 38293136 Fax +55 (0)31 38293516 Email: mailto:ssampaio@usiminas.com.br
Z25 and Z35 through thickness properties for plates of approved grades in the TM+Acc and TM+Acc+Temper conditions
Materials Quality Scheme Approved - MQS014

List 1
USINAS SIDERÚRGICAS DE MINAS GERAIS S.A. - São Paulo Steelmaking B.O.S. / Con Cast As below
USIMINAS

EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 80
Rodovia Cônego Domênico Rangoni, Km 6

Vila da Indústrias 11573-900
Cubatão - São Paulo
Tel: +55 13 3362-2978 Fax: +55 13 3362-3775 Email: mailto: takayochi.ueno@usiminas.com Web:http://www.usiminas.com
Specified through thickness properties for plates in the normalised condition, rolled from ingots, up to 35 mm thickness.
Specified through thickness properties for plates of grades up to DH32 and thickness up to 26mm in the normalised condition, rolled from continuously cast
slab.
Material Quality Scheme approved, MQS 044
Bulgaria
STOMANA INDUSTRY AD Sofia Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms/Billets As below 200
Plates Normal Strength A 40
Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36 40
360FG, 410FG, 460FG, 490FG, 510FG 40
1, Vladaysko Vastanie Str.
2304 Pernik
Tel: +359 894 751 381 Fax: +359 766 81952
email:vsofteva@stomana.bg web: www.stomana.bg
Canada
ESSAR STEEL ALGOMA INC. Toronto Steelmaking B.O.S. / Con Cast As below
Plates Normal Strength D, E 50
A, B 60
Boiler & Pressure Vessel 360FG, 410FG, 460FG, 490FG, 510FG 65
105 West Street
Sault Ste. Marie
Ontario
P6A 5P2
Tel +1 705 945 2347 Fax: +1 705 945 2632
e-mail: lori.pilot@algoma.com web: www.essarsteelalgoma.com

GERDAU AMERISTEEL WHITBY Toronto Steelmaking E.A.F. / Con Cast As below
Sections Normal Strength A, B 15
Higher Strength AH27S, AH32, AH36 15
Hopkin Street South
Whitby
Ontario L1N 5T1
CSA grades 260W, 300W and 350W may be accepted for approved applications as equivalent to the appropriate Lloyd's Register grade stated above.
Tel: +1 905 668 8811 ext 2744 Fax: +1 905 668 9361 Email: mailto:rgriffith@gerdauamericsteel.com Web: http://www.gerdauameristeel.com
GERDAU LONG STEEL NORTH AMERICA Toronto Steelmaking E.A.F. / Con Cast As below
Sections Normal Strength A 26
CAMBRIDGE MILL
160 Orion Place,
Cambridge,
Ontario,
N1T 1R9
Tel: +1 519 740 2488 ext 1420 Fax: +1 519 623 2062
email: maryam.chamaneh@gerdau.com web: www.gerdaul.com/longsteel

List 1
China, People's Republic of

ANGANG STEEL COMPANY LIMITED Dalian Plates Normal Strength A, B, D, E 100
Higher Strength AH42, AH46, AH50, AH55, DH42, DH46, 80
DH50, DH55, EH42, EH46, EH50, EH55, FH42,
FH46, FH50, FH55
AH27S, AH32, AH36, DH27S, DH32, DH36, 100
DH40, EH27S, EH32, EH36, EH40, FH27S,
FH32, FH36, FH40
360FG, 410FG, 460FG, 490FG, 510FG 50
Ferritic Low Temperature 1.5Ni, 3.5Ni, 5Ni, 9Ni 40
HEAVY PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT
Honqi Road, Lishan District,
Anshan City,
Liaoning Province
Tel: +86 412 673 4836 Fax: +86 412 672 5766 Email mailto:hp318@sina.com Web http://www.ansteel.con.cn
All grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.
ANGANG STEEL COMPANY LIMITED Dalian Steelmaking B.O.S. / Con Cast As below
Semi-Finished Slabs Normal strength, Higher Strength 300
Plates Normal Strength A, B, D 40
360FG, 410FG, 460FG, 490FG, 510FG 40
MEDIUM PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT
Angang Area
Anshan City
Liaoning Province
Tel +86 0412 675 1030 Fax +86 0412 675 2819 Email mailto:zy-zb-111@163.com
Slabs as semi finished products nominal 2000mm width x nominal 7000mm length to the above maximum thickness are approved for further processing for
rolled products.
Certificate No. MD00/2757/0007/1 Expiry date: 23/10/2014
ANGANG STEEL COMPANY LIMITED Dalian Hot Rolled Coil Normal Strength A, B, D 20
EH27S, EH32, EH36
HOT STRIP MILL OF ANGANG STEEL COMPANY LIMITED
Angang Production Area,Tiexi District
114024
Tel: +86 412 6757143 Fax: +86 412 6753575
Email: agwanrui@163.com
Web http://www.ansteel.com.cn
ANGANG STEEL COMPANY LIMITED Dalian Steelmaking B.O.S. / Con Cast As below
Semi-Finished Blooms/Billets carbon-manganese, carbon, carbon manganese 250
Higher Strength AH32, AH36, AH40, DH32, DH36, DH40, EH32, 40
EH36, EH40
BAYUQUAN 5500 HEAVY PLATE MILL
115000 Bayuquan
Yingkou City
Liaoning Province
Tel: +86 412 6334292 Fax: +86 412 6722093 Web: www.ansteel.com.cn
ANYANG IRON & STEEL CO., LTD. Wuhan Steelmaking B.O.S./E.A.F./Con Cast As Below
Semi-Finished Slabs Normal strength 230
Boiler & Pressure Vessel 360AR, 410AR, 460FG, 490FG, 510FG 36
360FG, 410FG 40
Yindu District
Anyang City
Henan Province
Tel: +86 372 3120163 Fax: +86 372 3120146
email: 197ma@163.com
web: www.anyang.com.cn

List 1
BAOSHAN IRON & STEEL CO., LTD. Shanghai Port Steelmaking B.O.S. / Con Cast As below
B.O.S. / Ingot As below
Blooms/Billets carbon, carbon-manganese, Alloy 500
Higher Strength AH42, AH46, AH50, AH55, DH42, DH46, 50
DH50, DH55, EH42, EH46, EH50, EH55
AH40, DH40, EH40, FH27S, FH32, FH36, FH40 68
AH27S, AH32, AH36, DH27S, DH32, DH36, 100
EH27S, EH32, EH36
Ferritic Low Temperature LTAH40, LTDH40, LTEH40, LTFH27S, LTFH32, 68
LTFH36, LTFH40
LTAH27S, LTAH32, LTAH36, LTDH27S, 80
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36
Hot Rolled Coil Normal Strength A, B, D 22
Higher Strength AH32, AH36 12
Boiler & Pressure Vessel 460FG, 490FG, 510FG 12
360FG, 410FG 22
Core Base
No 885, Fujin Road
Baoshan District
Shanghai 201900
Tel +86 21 2664 8888 Fax +86 21 2664 8000
Web:http://www.baosteel.com
Including all plate grades and thicknesses with specified through thickness properties (Z35)
Materials Quality Scheme Approved - MQS 038
BAOSHAN IRON & STEEL CO., LTD. Shanghai Port Steelmaking B.O.S. / Con Cast As below
EH27S, EH32, EH36
360FG, 410FG 60
Core Base Plate Line No. 2
No. 777 North Wenchuan Road
Baoshan District
Shanghai 200949
Tel +86 21 266488888 Fax +86 21 2664 8000 Email: to: huangjh@baosteel.com Web:http://www.baosteel.com
Semi-finished products in carbon, carbon-manganese fine grain (element combinations as stated, slabs to 2300mm wide, to 12000mm long to 54 tonnes for
further processing to rolled products
Z25 & Z35 designations made be added for plates up to 35mm thick produced in the as rolled condition from concast slab for grades A, B and D with
specified through thickness properties
Z25 & Z35 designations made be added for plates with specified through thickness properties for the approved grades in the normalised condition, normalised
rolled condition, TM condition and TM +Acc condition
Z25 & Z35 designations made be added for plates up to 40mm thick produced in the normalised rolled condition from concast slab for grades DH36 and DH32
with specified through thickness properties

BENGANG STEEL PLATES CO., LTD. Dalian Steelmaking B.O.S. / Con Cast As below
Hot Rolled Coil Normal Strength A, B 20
Plates from coils Normal Strength A, B 20
No. 18, Gangtie Road, Pingshan District
Benxi City
Liaoning Province
Tel 0414 7827678 Fax: 0414 7827814 Email:zyjfx@sina.cn
CHANGSHU LONGTENG SPECIAL STEEL CO., Jiangyin Sections Normal Strength A, B, D 14
LTD.

List 1
No. 9 Jusha Road
Meili Town
Changshu City
Jiangsu Province 21551
Tel: +86 0512 5206 1085 Fax: +86 0512 5266 1141 Email: mailto: lttg@lttg.cn Web: http://www.lttg.cn
Certificate #: MD00/3275/0004/1 Expiry date: 10/10/2015 #ENHANCED SURVEY#
CHANGSHU LONGTENG SPECIAL STEEL CO., Jiangyin Steelmaking E.A.F. / Con Cast As below
LTD.
Semi-Finished Ingots (tonnes) carbon, carbon-manganese, alloy 26
Blooms Normal Strength, Higher Strength 260
118 Hualian Road,

Tonggang Industrial Park,
Meili Town, Changshu City,
Tel.:+86 512 5266 1284 Fax.: +86 512 52661284 Email: mailto: lttg@lttg.cn Web: http://www.lttg.cn
Blooms as semi finished products nominal 340mm width x nominal 12000mm length to the above maximum thickness are approved for further processing for
rolled products.
CISCO Wuhan Steelmaking B.O.S. / Con Cast As below
EH27S, EH32, EH36
Boiler & Pressure Vessel 360AR, 410AR, 460AR 40
360FG, 410FG, 460FG, 490FG 80
Chongqing Iron and Steel Co., Ltd.
Jiangnan Town (4100 Mill)
Changshou District
Chongqing
Tel: +86 23 6887 3543 Fax: +86 23 6887 3543
Email: egetu@126.com
Web: http://www.cggf
Certificate Number: MD00/3763/0006/1 Expiry date: 28/03/2016
CISCO Wuhan Plates Normal Strength A, B, D, E 40
EH27S, EH32, EH36
Boiler & Pressure Vessel 360AR, 410AR, 360FG, 410FG, 460FG, 490FG, 40
510FG
Chongqing Iron and Steel Co., Ltd.
Jiangnan Town (2700 Mill)
Tel: +82 623 6887 3543 Fax: +82 623 6887 3543 Email: zyflwy@163.com Web: http://www.cggf
Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to all Grades and supply conditions.
DAYE SPECIAL STEEL CO., LTD. Wuhan Steelmaking B.O.S. / Con Cast As below
E.A.F./Ingot/Con Cast As below
Bars carbon, carbon-manganese, alloy 650
Bars Structural carbon, carbon-manganese 190
Machinery carbon, carbon-manganese, alloy 190
Chain Cable Stock U1, U2, API-2F 110
U3, R3S, R4 160
316 Huangshi Avenue
Huangshi City
Hubei Province
Post code: 435001
Tel: +86 714 629 7888 Fax: +86 714 629 7781 Email: chenlei7483@163.com Web: http://www.dayesteel.com.cn
Mooring grade bars (grade R4) are restricted to supply to Zhengmao Group Co., Ltd.
Mooring grade bars (grade R3S) are restricted to supply to Foshan Marine Anchor Chain Ltd. (FMAC)

DONGBEI SPECIAL STEEL GROUP Dalian Steelmaking B.O.S. / Con Cast carbon, carbon-manganese, alloy
E.A.F./Ingot/Con Cast carbon, carbon-manganese
Blooms/Billets carbon, carbon-manganese 280
Bars carbon, carbon-manganese 200
Chain Cable Stock U1, U2, U3 130

List 1
BEIMEN SPECIAL STEEL CO., LTD.
Fularji District
Qiqihar City
Heilongjiang Province
Tel: +86 452 6801920 Fax: +86 452 6801496
Email: mailto:lhy999@163.net
Certificate #: MD00/2907/0001/1
Expiry date: 30/07/2014
DONGBEI SPECIAL STEEL GROUP Dalian Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy 27
FUSHUN SPECIAL STEEL CO. LTD.,
East No 8 Anshan Road,
Wanghua District,
Fushun City,
Liaoning Province
Tel No: +86 413 668 9161-3668 Fax no: +86 413 6674090
Email:
Web: www.dtsteel.com
Certificate No MD00/3945/0001/1
FUJIAN PROVINCIAL SANSTEEL (GROUP) CO., Guangzhou Steelmaking B.O.S. / Con Cast As below
LTD.
Plates Normal Strength A, B 36
360, 410 36
Middle Gongyezhong Road

Meilie District
Sanming City
Fujian Province
Tel: +86 598 8205936 Fax: +86 598 8205138
Email: hic099@126.com
Web: www.fjsg.com.cn
GUANGXI LIUZHOU Guangzhou Steelmaking B.O.S. / Con Cast As below
IRON & STEEL (GROUP) COMPANY
117 Beique
Liuzhou
Guangxi
Tel: +86 (0)772 2592132 Fax: +86 (0)772 2592784 Email mailto:lspzk@163.com Web http://www.liuzousteel.com
HANBAO IRON & STEEL CO. LTD (HANSTEEL Wuhan Steelmaking B.O.S. / Con Cast As below
GROUP)
Plates from coils Normal Strength A, B, D 18
Higher Strength AH27S, DH27S, AH32, DH32, AH36, DH36 18
232,Fuxing Road,
Handan,
Hebei. 056015
Tel +86 310 6073275 Fax No. + 86 310 6072241
Email jiashibo@mail.hgjt.cn
Web www.hgjt.com.cn
Certificate No MD00/3874/0002/ 1 Expiry Date 09/01/2017
HEBEI IRON & STEEL CO., LTD. Wuhan Steelmaking B.O.S. / Con Cast As below
Higher Strength AH27S, DH27S, EH27S 38
AH32, AH36, DH32, DH36, EH32, EH36 50
360FG, 410FG, 460FG, 490FG, 510FG 50

List 1
Handan Branch
232 Fuxing Road
Handan City
Hebei Province
056015
Tel: +86 310 607 2202 Fax: +86 310 607 2241 Email mailto:longzhengmin@163.com Web: http://www.hgjt.com.cn
Slabs as semi-finished products nominal 1800mm width x nominal 3200mm length to the above maximum thickness are approved for further processing for
rolled products.
Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied for approved grades supplied in the normalized
condition
HEBEI JINGYE CUT DEAL CO. LTD., Dalian Steelmaking B.O.S. / Con Cast As below 220
Higher Strength AH27S, AH32, AH36, DH32, DH36 30
Nandian Town
Pingshan County
Shijiazhuang City
Hebei Province
Tel No +86 311 8287 3953 Fax No +86 311 82873988 Mob +86 158 3111 8888
Email jingye@hbjyjt.com
Web www.hbjyjt.com
Certificate No MD00/4022/0001/1 Expiry Date 09/05/2015
HEBEI JITAI SPECIAL STEEL GROUP CO., LTD. Dalian Steelmaking E.A.F. / Con Cast As below
Sections Normal Strength A, B, D 20
Bars Normal Strength A, B 38
Feng Village
Lincheng County
Xingtai City
Tel +86 319 7018893 Fax +86 319 3033326
Email: mailto:13780444117@vip.sohu.com
Web: htpp://www.jitaichina.cn
HENGYANG VALIN STEEL TUBE CO., LTD. Wuhan Steelmaking E.A.F. / Con Cast As below
Semi-Finished Billets carbon, carbon-manganese 330
No. 10 Dalixincun
Hengyang City
Hunan Province 421001
Tel: +86 734 8872311 Fax: +86 734 8873769
Email: hgscjf@163.com
Web: www.hysteeltube.com
HUNAN VALIN LIANYUAN STEEL CO., LTD. Wuhan Steelmaking B.O.S. / Con Cast As below
Huangnitang, Loudi
Hunan Province
Post Code: 417009
Tel +738 8661473 Fax +7388663570
Email: pmy@lysteel.com
web: www. lysteel.com
Certificate #: MD00/3999/0001/ Expiry date: 06/03/2015
INNER MONGOLIA NORTH Wuhan Steelmaking E.A.F. / Ingot As below
HEAVY INDUSTRIES GROUP CO., LTD.
Binggong Road, Qingshan District
Baotou City
Inner Mongolia
014033
Tel No:+86 742 338 6297 Fax No: +86 742 334 0042
Email: bfzg-tsgs@163.com
Web http://www.bfzg.com
Including semi-finished as-forged bars to 8.5 tonnes in carbon, carbon-manganese and alloy steel for further process of forge

JIANGSU SHAGANG GROUP Nanjing Steelmaking B.O.S. / Con Cast As below
E.A.F. / Con Cast As below
Semi-Finished Blooms carbon, carbon-manganese 200
Billets carbon, carbon-manganese 150
Machinery carbon, carbon-manganese 100
Chain Cable Stock U2 140
U3 210

List 1
HUAIGANG SPECIAL STEEL CO., LTD
No. 188 South Xi'an Road
Huai'an City
Jiangsu Province
Tel: +81 517 83036135 Fax: +81 517 83631344
Email:3036135@sina.com
Web: http://www.huaigang.com
The approval for rolled bars over 60mm diameter is for steel manufactured by the B.O.S. / Con Cast route.
Bars for chain cable stock are intended for final heat treated conditions; Grade U2 normalized; Grade U3 quenched and tempered.
Chain cable stock bars may be accepted up to 250mm diameter may be accepted for further processing for forged chain cable fittings.
Blooms, billets and bars as semi finished-products are approved for further processing for rolled products; blooms nominal maximum width 200mm x nominal
maximum length 12000mm; billets nominal maximum width 150mm x nominal maximum length 12000mm; bars nominal maximum length 12000mm; to the
above maximum thicknesses.
JIANGSU SHAGANG GROUP CO., LTD Jiangyin Steelmaking B.O.S. / Con Cast As below
Hongfa Steel Plant
Steelmaking Plant Number 1
Jinfeng Town
Zhangjiagang City
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email mailto: ctoec@shagang.cn Web http://www.sha-steel.com
Approval covers for con cast slabs to nominal sizes 2065mm wide x 9000mm long to the above maximum thickness for further processing for rolled products.
Certifcate Number: MD00/3127/0007/1 Expiry date: 27/10/2016
JIANGSU SHAGANG GROUP CO., LTD Jiangyin Plates Normal Strength A, B, D, E 100
Higher Strength AH27S, AH32, AH36, AH40, AH42, AH46, 100
AH50, AH55, AH62, AH69, DH27S, DH32,
DH36, DH40, DH42, DH46, DH50, DH55,
DH62, DH69, EH27S, EH32, EH36, EH40, EH42,
EH46, EH50, EH55, EH62, EH69, FH27S, FH32,
FH36, FH40, FH42, FH46, FH50, FH55, FH62,
FH69
360FG, 410FG, 460FG, 490FG, 510FG 100
Hongfa Steel Plant
Steel Plate Mill Line No. 1
Jiangsu Province, 215625
Tel +86 0512 58568791 Fax: +86 0512 58558900 Email: mailto:ctotec@shagang.cn Web: http://www.sha-steel.com
Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to
60.0mm.
Plates in Grades D and E Fine Grain Al+Ti+Nb in the TM+Acc condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to 60.0mm.
Plates in the Normalizing Rolled condition and the TM+Acc condition are restricted to a maximum width of 4150mm.
Plates in the quenched and tempered supply condition >70mm thickness are accepted for approved applications only.
Plates in higher strength grades AH32 and AH36 as rolled 2800 wide x 11,000 long
JIANGSU SHAGANG GROUP CO., LTD Jiangyin Plates Normal Strength A, B, D, E 60
Higher Strength AH27S, AH32, AH36, AH40, DH27S, DH32, 60
DH36, DH40, EH27S, EH32, EH36, EH40,
FH27S, FH32, FH36, FH40
Boiler & Pressure Vessel 360AR, 410AR, 460AR, 360FG, 410FG, 460FG, 40
490FG, 510FG
Hongfa Steel Plant
Steel Plate Mill Line No. 2
Tel +86 0512 5856 8791 Fax: +86 0512 5855 8900 Email: mailto:ctotec@shagang.cn Web: http://www.sha-steel.com
Plates in the Normalizing Rolled are restricted to a maximum width of 4650mm condition and in the TM+Acc condition are restricted to a maximum width of
4150mm.
Plates in the Normalizing Rolled condition and the TM+Acc condition are restricted to a maximum width of 4150mm.
Plates in AH32 and AH36 as rolled 2800 x 11,000 and approved in the "as welded"condition
JIANGSU SHAGANG GROUP CO., LTD Jiangyin Steelmaking B.O.S. / Con Cast As below
Hongfa Steel Plant
Steelmaking Plant Number 2
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email mailto: ctoec@shagang.cn Web http://www.sha-steel.com
Approval covers for con cast slabs to nominal sizes 2065mm wide x 9000mm long to the above maximum thickness for further processing for rolled products.
JIANGSU SUNAN SPECIAL EQUIPMENT GROUP Jiangyin Steelmaking E.A.F. / Ingot As below
CO., LTD.

List 1
WEST OF BAI DANGQIAO
TONGGANG ROAD
CHANGSHU
JIANGSU
Tel: +86 512 5263 1888 / 1908 Fax: +86 512 5263 7910 email: 52631569@163.com Web: http://snzbjt.com
Ingots as semi finished products nominal 1170/1290mm diameter x nominal 3000mm long to the above maximum weight are approved for further processing
for forgings
JIANGYIN BOFENG IRON & STEEL CO., LTD. Jiangyin Sections Normal Strength A, B 30
Huaxicun Industrial Zone
Jiangyin City
Jiangsu Province
Tel: +86 510 8621 7672 Fax: +86 510 8621 7672 Email: office2@bofengsteel.com Web: http://www.bofengsteel.cn
The approved sections are in the form of universal flats nominal widths <600mm to the maximum thickness shown above.
JIANGYIN CHANGDA STEEL CO., LTD. Jiangyin Plates Normal Strength A, B 25
No. 388, West Binjiang Road,
Jiangyin City,
Jiangsu Province, 214442,
Tel: +86 510 8603 2250 Fax: +86 510-8603 2250 Email: panxun1@sina.com Web: http:// www.chdsteel.com
Plates are restricted to a maximum width of 2200mm.
JIANGYIN HUAQIANG SPECIAL STEEL Jiangyin Steelmaking E.A.F. / Ingot As below
CASTING & FORGING THERMOELECTRIC CO., LTD.
No. 18, Biangang Road,
Huaxi, Jiangyin City,
Jiangsu Province, 214421,
Tel: +86 510 860 60566 Fax: +86 510 860 60512 Email: mj2_hq@163.com Web: http://www.jyhuaqing.com
Ingots as semi finished products nominal 1240mm/1320mm diameter x 2770mm long to the above maximum weight are approved for further processing for
forgings.
JIANGYIN XINGCHENG SPECIAL STEEL WORKS Jiangyin Steelmaking B.O.S./E.A.F./Con Cast As Below
CO., LTD.
Bars Semi-finished Products carbon, carbon-manganese, alloy 900
Structural carbon, carbon-manganese, alloy 180
Chain Cable Stock R3, R3S, R4 160
U1, U2, U3 180
297, Bin Jiang East Road

Jiangyin City
Jiangsu province 214429
Tel: +86 510 6193388-6165 Fax: +86 510 6195042 Email: mailto:jyxctg@public1.wx.js.cn Web: http://www.jyxc.com
JIANGYIN XINGCHENG SPECIAL STEEL WORKS Jiangyin Steelmaking B.O.S. / Con Cast As below
CO., LTD.

EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 50
3500 Plate Mill


List 1
JIANGYIN XINGCHENG SPECIAL STEEL WORKS Jiangyin Plates Normal Strength A, B, D, E 80

CO., LTD.
Higher Strength DH40, EH40, FH27S, FH32, FH36, FH40 60
AH27S, AH32, AH36, DH27S, DH32, DH36, 80

EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 80
4300 Plate Mill

Plates in the Normalizing Rolled and Thermomechanical supply conditions are restricted to 3800mm maximum width.
Plates in the TM+Acc supply condition are restricted to thickness from 16mm to the maximum thickness shown above.
Z35 designation for through thickness properties may be added to all plates in the above supply conditions.
KOCEL STEEL FOUNDRY CO., LTD. Wuhan Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy 10
199#, Tongxin Nan Road
Economic and technical development District
Yinchuan, Ningxia
Tel: 0951 2031028 Fax: 0951 2031218
email: david.li@kocel.com web: www.kocel.com
Certificate No. MD00/3515/0002/1 Expiry Date: 22/04/2017

KUNSHAN DAEKYUNG STAINLESS STEEL CO., Shanghai Port Plates Austenitic Stainless 304L, 316L 80
LTD
No. 66 Longdeng Road
Kunshan Economy Technology Development Zone
Kunshan
Jiangsu Province
Tel:+86 512 57900998 Fax: +86 512 57700372
Email: cuiyongxun020@sina.com
LAIWU STEEL GROUP LTD. YINSHAN SECTION Qingdao Steelmaking B.O.S. / Con Cast As below
STEEL CORPORATION
Semi-Finished Slabs As below 300
Higher Strength DH40, EH40, FH32, FH36, FH40 50
AH32, AH36, DH32, DH36, EH32, EH36 80
360FG, 410FG, 460FG, 490FG, 510FG 80
Shuangyuan Road,
Gangcheng district,
Laiwu,
Shandong
Tel: +86 634 7920316 Fax: +86 634 6820824
email: hao781109@126.com web: www.laigang.net

MAANSHAN IRON & STEEL COMPANY LIMITED Nanjing Steelmaking B.O.S. / Con Cast As below
Higher Strength AH32, AH36, DH32, DH36 25
No.8 Jiuhua West Road,
Maanshan City
Anhui Province PC:243000
Tel: +86 555 287 7110 Fax: +86 555 2886 904
Email: mailto:jjsskk2005@yahoo.com.cn.
Web http://www.magang.com.cn
MINMETALS YINGKOU MEDIUM PLATE CO., Dalian Steelmaking B.O.S. / Con Cast As below
LTD.

List 1
China, People's Republic of

MINMETALS YINGKOU MEDIUM PLATE CO., Dalian Plates Higher Strength AH27S, DH27S, EH27S 40
LTD.
AH32, AH36, DH32, DH36, EH32, EH36 50
360FG, 410FG, 460FG, 490FG, 510FG 50
No 1 Fanrong Road, Yejin Street

Laobian District
Yingkou City
Liaoning Province
Tel: 086 (0)417 3256051 Fax: 086 (0)417 3256057
Email mailto:jszlb-wkyg@163.com
Web :www.wkyg.com
Plates with specified through thickness properties in listed grades of normal and higher strength steels.
NANJING IRON & STEEL CO., LTD. Nanjing Steelmaking B.O.S. / Con Cast As below
Blooms Normal Strength, Higher Strength 320
Billets Normal Strength, Higher Strength 150
Higher Strength AH40, DH40, FH27S, FH32, FH36, FH40 40
AH27S, AH32, AH36, AH42, AH46, AH50, 60
AH55, DH27S, DH32, DH36, EH27S, EH32,
EH36, FH42, FH46, FH50, FH55
DH42, DH46, DH50, DH55, EH40, EH42, EH46, 70
EH50, EH55
AH62, AH69, DH62, DH69, EH62, EH69 80
Boiler & Pressure Vessel 360AR, 410AR, 360, 410 25
360FG, 410FG, 460FG, 490FG, 510FG 60
Ferritic Low Temperature 5Ni 50
Bars Chain Cable Stock U1, U2, U3 180
Nanjing Works
XieJiaDian
Luhe District
Nanjing, Post Code: 210035
Tel: +86 25 5707 3657 Fax: +86 25 5707 4341
EMail mailto:wangwuyi@njsteel.com.cn
Web:http://www.njsteel.com.cn
Plates with specified through thickness properties may be accepted with the suffix Z35 applied to all approved grades of normal and higher strength steels.
Chain cable stock in Grades U2 and U3 is intended for further processing with quenched and tempered heat treatment, bars at 80mm diameter or less are
produced by BOS or EAF steelmaking, bars over 80mm diameter are produced by EAF steelmaking.
Billets and blooms as semi finished products to the above maximum thickness, nominal to 480mm width and to nominal 12000mm length are approved for
further processing for rolled products.
Slabs as semi finished products to the above maximum thickness, nominal to 2510mm width and to nominal 4000mm length are approved for further
processing for rolled products.

NANYANG HANYE SPECIAL STEEL CO., LTD., Wuhan Steelmaking B.O.S./Ingot/Con Cast As below
Huiche Town Industry Area,
Xixia County,
Nanyang City,
Henan Province
Tel No: +86 377 697 65211 Fax No: +86 377 697 65333
Email: zhaoyuan_521@sohu.com
Website: www.elongcheng.com
PANGANG GROUP Wuhan Steelmaking EAF/LRF/VD/Ingot Alloy 25
Carbon, Carbon-manganese 40
Semi-Finished Ingots (tonnes) alloy 25
carbon, carbon-manganese 40
ESR Ingots alloy 25
alloy 390
Bars Structural carbon, carbon-manganese, alloy 390

List 1
JIANGYOU CHANGCHENG SPECIAL STEEL CO., LTD.,
No.195, Jiangdong Road,
Jiangyou City,
Sichuan Province,
621701
Tel No: +86 816 365 087 Fax No: +86 816 3650463
Email zjbzgk@163.com
Web: http://www.cssc.com.cn
PANGANG GROUP PANZHIHUA STEEL & Wuhan Steelmaking B.O.S. / Con Cast See notes
VANADIUM CO. LTD.,
Semi-Finished Slabs See notes
Billets See notes
Panzhihua City,
Tel No: +86 0812 339 1756 Fax No: +86 0812 339 6014
Email: taoqy@163.com
Web: wwwpzhsteel.com.cn
Certificate No. MD00/4036/0002/1 Expiry 02/06/2015
PENGZHOU SANXIN MACHINERY Wuhan Steelmaking B.O.S./E.A.F./Ingot As Below
MANUFACTURE Co. Ltd.
No. 49 Mengsan Road, mengyang Town

Pengzhou City, Sichuan Province
P.C 611934
Tel: +86 28 83773044 fAX: +86 28 83773071
QINHUANGDAO SHOUGANG PLATE MILL CO., Dalian Plates Normal Strength E 32
LTD.
A, B, D 35

EH27S, EH32, EH36
360AR, 410AR 35
No. 409 Jianshe Street

Qinhuangdao City
Hebei Province
Tel: +86 010 88296326 Fax: +86 010 88291295 email: mailto: lin@165e.com
QINHUANGDAO SHOUQIN METAL MATERIALS Dalian Steelmaking B.O.S. / Con Cast carbon, carbon-manganese
CO., LTD.
Plates Normal Strength D 50
A, B 100
Higher Strength AH40 40
DH40, EH27S, EH32, EH36, EH40 50
AH36, DH27S, DH36 80
AH27S, AH32, DH32 100
360, 410 32
510FG 80
360FG, 410FG, 460FG, 490FG 100
Duzhuang
Funing County
Qinhuangdao
Hebei Province 066326
Tel +86 0335 6082696 Fax +86 010 6082690
Email: market@sq.shougang.com.cn
Web http://www.shouqin.com.cn
Certificate No: MD00/3136/0007/1 Expiry Date: 05/02/2017
All plate grades and thicknesses with through thickness properties, notations Z25 and Z35 may be added.

List 1
RIZHAO STEEL WIRE CO., LTD Qingdao Steelmaking B.O.S. / Con Cast As below
No. 600, Yanhai Road, Rizhao
Shandong
Tel: +86 633 6188070 Fax: +86 633 6188155
email. jzwanggang@rizhaosteel.com web: www.rizhaosteel.com
SANXIN HEAVY INDUSTRY MACHINERY CO., Jiangyin Steelmaking E.A.F. / Ingot As below
LTD
Xia Xi North Road,

Jiaze,
Wujin, Changzhou,
Jiangsu, 213148
Tel No +86 519 83685577 Fax +86 519 83586556
Email xxxxxxxxxxxxxxx
Web www.sanxinzg.com
SGIS SONGSHAN CO., LTD Guangzhou Steelmaking B.O.S. / Con Cast carbon, carbon-manganese
Semi-Finished Slabs carbon, carbon-manganese, alloy 270
Blooms carbon, carbon-manganese 425
AH27S, AH32, AH36, DH27S, DH32, DH36, 60
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 60
Bars Chain Cable Stock U3 150
Qujiang District
Shaoguan City
Guangdong 512123
Tel: +86 (0)751 878 5354 Fax: +86 (0)751 878 6066
email ly73@21cn.com
CEV is limited to a maximum of 0.45% for as rolled and nomalised higher strength steels but does not apply to TM steels
SHANDONG IRON & STEEL CO., Ltd. Qingdao Steelmaking B.O.S. / Con Cast As below
Plates Normal Strength E 50
A, B, D 60
DH36, DH40, EH27S, EH32, EH36, EH40, FH32,
FH36, FH40
360FG, 410FG, 460FG, 490FG, 510FG 60
JINAN COMPANY
21, Gongye Bei Road
Jinan, 250101
Shandong Province
Tel +86 531 8886 5844 Fax +86 531 8898 2126
email: jigangleike@163.com web: www.jigang.com.cn
SHANDONG SHOUGUANG JUNENG SPECIAL Qingdao Steelmaking B.O.S. / Con Cast As below
STEEL CO, LTD.
Semi-Finished Rolled Billets Carbon, Carbon-Manganese 310
No. 9 Tegang Road

Shouguang, Shangdong Province
262711
Tel +86 532 5186057 Tel+86 532 5186789

List 1
SHANGHAI HEAVY MACHINERY PLANT CO., Shanghai Port Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy 200
LTD.
1800 Jiangchuan Road
Minhang District
Shanghai
200245
Tel: +86 21 54724065ext 2027 Fax: +86 21 54721007 Email mailto:chenzq@sechig.com Web http://www.shmp.sh.com
Including ingots
SHANXI TAIGANG STAINLESS STEEL CO., LTD. Dalian Steelmaking E.A.F./A.O.D./Con Cast As below
Plates Austenitic Stainless 304L, 316L 20
Duplex Stainless UNS S31803 20
Stainless Steel Hot Rolling Mill
Jiancaoping Street No. 2
Taiyuan
030003
Taiyuan
Tel No: +86 351 3012029 Fax No: +86 351 3017893 Mob: 13503502921
Email: wangcd@tisco.com.cn
Web: http://tgbx.tisco.com.cn
SHANXI TAIGANG STAINLESS STEEL CO., LTD. Dalian Steelmaking B.O.S. / Con Cast As below
Boiler and Pressure Vessel 410 FG, 360 FG 25
Hot Strip Mill
Jiancaoping Street No. 2
Tel: +86 351 3012029 Fax: +86 351 3017893
Email: wangcd@tisco.com.cn Web: http: //tgbx.tisco.com.cn
Slabs as semi finished products 2310mm nominal width and 12000mm nominal length to the above maximum thickness are approved for further processing for
rolled products.
SHANXI TAIGANG STAINLESS STEEL CO., LTD. Dalian Plates Normal Strength A, B, D 40
Austenitic Stainless 304L, 316L, 304*, 316* 60
Linfen Heavy Plate Mill
Qiaodong Street No.3
Linfen City
Shanxi Province
Tel: +86 351 3017667 Fax: +86 351 3017893
Email: yangfei@tisco.com.cn
Web: http:// www.tisco.com.cn
Certificate No MD00/3688/0005/1 Expiry date 07/07/2015
SHANXI TAIGANG STAINLESS STEEL CO., LTD. Dalian Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy 12
Section Steel Plant,
No.2 Jian Caoping Street,
Taiyuan City,
Shanxi Province,
Tel: +81 (0)351 3017667 Fax: +81 (0)351 3017893
Certificate No. MD00/4240/0001/1 Expiry Date: 15/10/2016.

SHI GANG JING CHENG EQUIPMENT Dalian Steelmaking E.A.F. / Ingot As below
DEVELOPMENT
AND MANUFACTURING CO., LTD.

No. 1 East Xinlian Street
Administrative Committee of Liaoning(Yingkou)
Castal Industrial Base
Tel: +86 0417 3257866 Fax: +86 0417 3257860
Email: caojun@cyedm.com.cn
Web: http://www.cyedm.com.cn
SHIJIAZHUANG I & S CO., LTD. Dalian Steelmaking B.O.S. / Con Cast carbon, carbon-manganese

List 1
No. 363 Heping E Road
Shijiazhuang City
Hebei Province
Tel: +86 (0)311 869 12562 Fax: +86 (0)311 869 13368
Email: sunjp_sggs@126.com
SHOUGANG JINGTANG UNITED IRON & STEEL Qingdao Steelmaking B.O.S. / Con Cast As below
CO., LTD.
Higher Strength AH32, DH32, AH36, DH36 18
Caofeidian Industrial Zone, Tangshan

Post Code: 063200
Tel: +86 315 8872636 Fax: +86 315 8872606
email: uha_w@126.com web: www.sgjsteel.com

SHOUGANG QIAN'AN IRON & STEEL CO., LTD., Dalian Steelmaking B.O.S. / Con Cast As below
HEBEI
Binhe Village
Yang-dian-zi Town
Qian'an
Hebei, 064404
Tel: +86 315 7703138 Fax: +86 315 7703139
Email: mailto:zhengzhihui@sgqg.com
Web wwwsgqg.com
SICHUAN LIUHE FORGING CO., LTD. Wuhan Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy 8
Baolun Road(W), Henan Industrial Park
Jiangyou City
Sichuan Province
Tel No: +86 0816 3456788 Fax No: +86 0816 3521398
Email: bk.liwei'@gmail.com
SINOSTEEL (TIANJIN) STEEL PROCESSING Dalian Plates from coils Normal Strength A, B, D 18
CO.LTD
No 700 Hexing Road

Xin Xing Village,
Dongli District,
Tianjin
Tel No 0086 22 24982876 Fax No. 0086 22 24981723
Email yunqidi@163.com
Web tianjin.sinosteel.com
Cert No. MD00/3656/0002/1 Expiry date: 08/07/2015
Not approved for heat treatment
SUQIAN NANJING IRON & STEEL Nanjing Sections Normal Strength A, B, D 20
Higher Strength AH32, AH36, DH32, DH36, DH40 20
JINXIN STEEL ROLLING Co., Ltd.
No.89 Jingshan Road,
Suyu District,
Suqian City, Jiangsu,
Tel; +86 527 844 53907 Fax: +86 527 844 80094 Email: hzefeng@yahoo.com.cn
Certificate: MD00/3741/0003/1 Expiry date: 17/12/2014

List 1
SUZHOU SUXIN SPECIAL STEEL CO., LTD. Shanghai Port Steelmaking E.A.F. / Con Cast As below
Huashan, Tong An, Suzhou
Jiangsu
Post Code: 215151
Tel: +86 0512 8887 7088 Fax: +86 0512 88877815
TAI YUAN HEAVY INDUSTRY CO. LTD. Wuhan Steelmaking E.A.F. / Ingot As below, carbon, carbon-manganese
No.53, Yuhe Street,
Wanbailin District, Taiyuan City,
Shanxi Province, 030024,
Tel +86 351 636 6770 Fax: +86 351 636 6750
Email: litubin_9365@yahoo.com.cn
Web: www.tyhi.com.cn
TANGSHAN HEAVY PLATE CO., LTD. Dalian Steelmaking B.O.S. / Con Cast As below
Lingang Industrial Park
Leting County,
Tangshan City,
Hebei
Tel No: +86 315 4958304 Fax No: +86 315 4959038
Email tszhaoyujun@163.com

TANGSHAN SHENGCAI STEEL CO., LTD. Dalian Sections Normal Strength A, B 18
South of Xinghonglin Village
Angezhuang Town,
Luannan County, Tangshan City,
Hebei Province
Tel No: +86 315 445 1166 Fax No: +86 315 445 5599
Email 1624566075@qq.com
Web xxxxxxxxxxxxx
Certificate No: MD00/ 4131/ 0001/1 Expiry Date 19/03/2016
TANGSHAN XINXIN SPECIAL STEEL CO. LTD Dalian Sections Normal Strength A, B 14
No. 95 Middle Street
Bencheng Town, Luannan County
Tangshan City
Tel: +86 0315 412 5016; Fax: +86 0315 412 5016
Email:mailto: mengfen123@163.com
Web: www.xxtg.cn
TANGSHAN YANSHAN IRON & STEEL CO., LTD. Dalian Steelmaking B.O.S. / Con Cast As below
Billets Normal Strength 150
The West Side of Qianan Railway Station
Qianan City
Hebei Province (064403)
Tel: +86 315 7769 566 Fax: +86 315 7769 566
Billets nominal maximum width 150mm x 12,000mm nominal maximum length to the above maximum thickness supplied in the As Cast condition; slabs
nominal maximum width 1,800mm x 12,000mm nominal maximum length to the above maximum thickness supplied in the As Cast condition; are approved for
further processing for rolled products in the detailed strength levels.
TIANJIN IRON AND STEEL GROUP CO. LTD. Dalian Steelmaking B.O.S. / Con Cast As below
398 Jintang Road
Dongli District
Tianjin
Tel:+86 22 24706052 Fax: +86 22 24706052
Email: mailto:TGRZ166@yeah.net
web: www.tgsteel.com
TIANJIN PIPE (GROUP) CORPORATION Dalian Steelmaking E.A.F. / Con Cast carbon, carbon-manganese

List 1
No 396, Jintang Road
300301
Tel No: +86 22 2480 2296 Fax no: +86 22480 1291
Email zhangyh@tpco.cn
Web: www.tpco.com
TIANJIN TIANZHONG GIANT HEAVY INDUSTRY Dalian Steelmaking E.A.F. / Ingot carbon, carbon-manganese 90
CO., LTD.
No. 609, Jinyu Road
Xiditou Town
Beichen District
Tianjin
Tel:+86 (0)22 86885730 Fax: +86(0)22 8688 5730
TIANJIN YONGHENG ENTERPRISE CO., LTD. Dalian Sections Normal Strength A, B 15
Daqiuzhuang Town Industrial Zone
Tianjin
Tel:+86 (0)2228899290 Fax: +86(0)2260730999 Email:mailto:wy8770@163.com Web:http://www.tjyhsy.com
TONGYU HEAVY INDUSTRY Co., Ltd Qingdao Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy 70
High & New Technology Industry Development Zone,
Yucheng City,
Dezhou City,
Shandong Province,
Tel: +86 534 7520690 Fax: +86534 7521470
Certificate No. MD00/3998/0001/1 Expiry date:01/03/2015
WISCO Wuhan Steelmaking B.O.S. / Con Cast As below
360FG, 410FG, 460FG, 490FG, 510FG 50
Boiler and Pressure Vessel 360, 410 12
Wuhan Iron and Steel Co., Ltd.
Changqian
Qingshan
Wuhan
Tel: +86 27 8689 8498 Fax: +86 27 8689 2413
email: 782650488@qq.com web: www.wisco.com.cn

WUHAN HEAVY INDUSTRY Wuhan Semi-Finished Ingots (tonnes) carbon, carbon-manganese, alloy 100
CASTING AND FORGING CO., LTD.
1 Wudong Street
Quingshan District
Hubei
Tel No:+86 027 6886 1813 Fax No: +86 027 6886 1810 Mob :+86 13720291417
Email wh471zg@163.com
Web www.whzg.com.cn
WUHAN IRON & STEEL GROUP Wuhan Steelmaking B.O.S. / Con Cast As below
Semi-Finished Slabs As below, Normal strength, Higher Strength 300
ECHENG IRON & STEEL CO., LTD.
Wuchang Dadao No. 105
Ezhou City
Hubei Province, 436002
Tel: +86 711 3233225 Fax: +86 711 3233225 Email mailto: chencaiyuan@sina.com
WUHAN ZHONGYE MACHINERY WHOLE SET Wuhan Steelmaking E.A.F. / Ingot As below
EQUIPMENT

List 1
Gourp Co., Ltd.
DAYE BRANCH
Lingcheng Road No. 2
Lingxiang Town, Daye City
Hubei Province
Tel: +86 0714 370 2019 Fax: +86 0714 370 2196
Email : ZG1819ZG@163.com
WUYANG IRON & STEEL COMPANY LTD. Wuhan Steelmaking E.A.F./Ingot/Con Cast As below
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 100
Wugang City
Henan Province
P.N: 462500
Tel: +86 375 811 1230 Fax: +86 375 811 4006
Plates with specified through thickness properties in listed grades of normal and higher strength steels.
WUYANG IRON & STEEL COMPANY LTD. Wuhan Plates Normal Strength A, B, D, E 100
Higher Strength FH32, FH36, FH40 50
AH27S, AH32, AH36, AH40, DH27S, DH32, 100
DH36, DH40, EH27S, EH32, EH36, EH40
Wuyang New Wide and Heavy Steel Plate Co Ltd
Wugang City,
Henan Province,
PN 462500
Tel No. +86 375 8111230 Fax No. +86 375 8114006 Email to: wghangweijun@163.com
Plates with specified through thickness properties in listed grades of normal and higher strength steels
Certificate No. MD00/3714/0002/1 Expiry Date 14/07/2014
XINING SPECIAL STEEL CO., LTD. Wuhan Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy
ESR Ingots carbon, carbon-manganese, alloy 18
No. 52 Chaidamu West Road
Xining
Qinghai Province, 455004
Tel: 0086 0971 529 9294 Fax: 0086 0971 529 9407
Email: cyuian@sina.com
Web: www.xntg.com
XINYU IRON & STEEL CO. LTD. Wuhan Steelmaking B.O.S. / Con Cast See notes
E.A.F. / Con Cast See notes
Higher Strength FH27S, FH32, FH36, FH40 50
AH27S, DH27S, DH40, EH27S, EH40 60
AH32, AH36, DH32, DH36, EH32, EH36 80
360, 410 60
360FG, 410FG, 460FG, 490FG, 510FG 80
1 Yejin Road
Xinyu City
Jiangxi Province 338001
Tel: 0790 6293212 Fax: 0790 629 3826
Email: xy6279918@126.com
Web: www.xinsteel.com.cn
All grades with specified through thickness properties, designation to Z35 may be added
XISC - HUNAN VALIN XIANGTAN Wuhan Steelmaking B.O.S. / Con Cast As below
Higher Strength AH40, DH40, EH40, FH40 40
FH27S, FH32, FH36 60
AH27S, AH32, AH36, DH27S, DH32, DH36, 100
EH27S, EH32, EH36
Ferritic Low Temperature LTAH32, LTAH36, LTAH40, LTDH32, LTDH36, 40
LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,
LTFH36, LTFH40

List 1
IRON & STEEL CO., LTD.
Yuetang District,
Xiangtan City,
Hunan Province,
Approved for Z25 & Z35 grades.
Tel +86 (0)731 5865 2130 Fax +86 (0) 731 58653050
Email mailto:hnxgjiazg@sohu.com
Web http://www.hnxg.com.cn
YANTAI WALSIN STAINLESS STEEL CO., LTD. Qingdao Steelmaking B.O.S/V.O.D./Con Cast austenitic stainless
Semi-Finished Blooms/Billets austenitic stainless steel 220
No. 2 Wuzhishan Road,
Economic Technical Development Zone
Yantai City, shandong Province
Tel: +86 535 2166688 Fax: +86 535 2165008 Email:Jack_yen@walsin
YONGXING SPECIAL STAINLESS STEEL CO LTD Shanghai Port Steelmaking E.A.F. / Ingot austenitic stainless
Semi-Finished Ingots (tonnes) austenitic stainless 5
Bars Semi-finished Products austenitic stainless 110
Yangjiabu,
Huzhou City,
Zhejiang Province
Tel No. +86 572 2350629 Fax No: +86 572 2351517
Email: wang _jianyong@163.com
Web : www.yongxingbxg.cn
Certificate No. MD00/3791/0003/1 Expiry date 06/06/2016
ZENITH STEEL GROUP CO., LTD. Jiangyin Steelmaking E.A.F. / Con Cast As below
Bars Chain Cable Stock U3 113
Beside 312 National Highway
Yinshu Village, Yaoguan Town
Changzhou, Jiangsu
Tel No. +86 519 88771301 Fax No: +86 519 88771301
Email: ludengyao@126.com
ZHEJIANG TIANJI HEAVY INDUSTRY Shanghai Port Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy 16
MACHINERY CO., LTD.
No. 463 Busen Road,
Fengqiao Town,
Zhuji City,
Zhejiang Province,
Tel: +86 575 8704 1127 Fax: +86 575 8704 5392
web: www.zhengtian.com.cn
Certificate No. MD00/4069/0001/1 Expiry Date: 23/08/2015
ZHEJIANG TSINGSHAN IRON & STEEL CO.LTD. Ningbo Steelmaking IF/AOD/Ingot/ConCast austenitic stainless steel
Blooms/Billets austenitic stainless steel 240
Billets austenitic stainless 150
Xiaoshi Industry Zone
Wenxi Town,
Qingtian,
Zhejiang Province
Tel No. 0086 578 6071 658 Fax No. 0086 578 6071 658
Email lw@ruipt.com
Web : www. zjqingshan.cn
Cert no. MD00/3673/0002/1 Expiry date: 25/08/2015
ZHONGPU (HANDAN) IRON AND STEEL CO., Dalian Steelmaking B.O.S. / Con Cast As below
LTD.
No.1 Steel Making Plant

Yangyi Town
Wuan City
Hebei Province, 056305
Tel: +86 (0)310-5178928 Fax: +86 (0)310-5178928 Web:http//www.hbpygt.com.cn Email: mailto:15130025086@139.com
web: www.hbpygt.com

List 1
ZHONGPU (HANDAN) IRON AND STEEL CO., Dalian Steelmaking B.O.S. / Con Cast As below
LTD.
No.2 Steel Making Plant

Yangyi Town,
Wuan City,
Tel: +86 (0)310-5178900 Fax: +86 (0)310-5178928
Web:http//www.hbpygt.com.cn
web: www.hbpygt.com
Certificate #: MD00/4034/0001/1 Expiry date:10/06/2015
Croatia
ABS SISAK d.o.o. Zagreb Steelmaking E.A.F. / Con Cast As below
BRAaE KAVURIaA 12,
44010 Sisak,
Tel: +385 44 565467
email: t.marjanovic@absacciai.it
Cert No. MD/00/4210/0001/1 Expiry date: 25/07/2016
Cuba
ACINOX LAS TUNAS Havana Steelmaking E.A.F. / Con Cast As below
Circuvalante Norte Km. 3 1/2
CP75100
Las Tunas
Tel: +53 131 46801 Ext 109 Fax: +53 131 46512 Email: eduardo@acinoxtunas.co.cu Web http://www.acinoxtunas.cu
Certifcate: MD00/3698/0002/1 Expiry date: 23/05/2014
Czech Republic
ARCELOR MITTAL TUBULAR PRODUCTS Prague Fabricated Sections Structural Sections carbon, carbon-manganese 5
KARVINA A.S.
Rude armady 471
733 23 Karvina
Tel: +420 596 391 330 M: +420 724 555 571 Fax: +420 598 391 337
Email to: daniel.stolarz@arcelormittal.com Web http://www.jakl.cz
Longitudinal high frequency induction (HFI) welded tubes, pipes and hollows
ARCELORMITTAL ENGINEERING PRODUCTS Prague Steelmaking B.O.S. / Con Cast carbon, carbon-manganese, alloy
OSTRAVA s.r.o
alloy 180
Bars Normal Strength A, B, D 60

List 1
Vratimovská 689
707 02 Ostrava-Kuncice
Approval for semi finished products covers con cast slabs to 150 x 1270mm, con cast billets to 180 x 180mm and con cast rounds to 400mm diameter.
Tel: +420 59 568 4130

email: shahab.husain@arcelormittal.com
web: www.arcelormittal.com/ostrava

EVRAZ VITKOVICE STEEL, a.s. Prague Steelmaking B.O.S. / Con Cast As below
EH27S, EH32, EH36
709 00 Ostrava - Hulvaky
Stramberska c.p. 2871/47
PSC 709 00
Tel: +420 59 595 5842 Fax: +420 602 485 466 Email: mailto:miroslav.snajdr@cz.evraz.com Web: http://www.evrazvitkovicesteel.com
Approved for plates with specified through thickness properties (Z35) in all grades up to 50 mm thickness.
Semi-finished products in carbon and carbon-manganese steels with fine grain: slabs to 1580mm wide to 8000mm long for further processing for rolled products

PILSEN STEEL s.r.o. Prague Steelmaking E.A.F. / Ingot As below
Tylova 1/57
316 00 Plzen
Tel: +420 378 134 225 Fax: +420 378 132 058
Email: karel.rau@pilsensteel.cz
Web: www.pilsensteel.cz
SOCHOROVÁ VÁLCOVNA TZ, a.s. Prague Bars Structural carbon, carbon-manganese, alloy 300
272 01 Kladno-Drin
Tel No +420 558 536 065 Fax No. +420 558 534 926
Email vit.prochazka@trz.cz
Web www.trz.cz
Machinery grade bars with the maximum diameter of 300 mm produced from con-cast blooms may be accepted with a minimum rolling reduction of 3:1.
TRINECKÉ ŽELEZÁRNY, a.s. Prague Steelmaking B.O.S./Ingot/Con Cast As below
Bars Machinery carbon, carbon-manganese, alloy 90
Chain Cable Stock U1, U2 72
Prumyslová 1000
Staré Mesto
739 61 Trinec
Tel: +420 558 534 016 Fax: +420 558 536 060
Email: mailto:radim.raska@trz.cz
Web hppt://www.trz.cz
Certificate #: MD00/1562/0007/1 Inspection Due: 12/07/2016
TRINECKÉ ŽELEZÁRNY, a.s. Prague Sections Normal Strength B, D 40
A 50
Higher Strength DH32, DH36 40
AH27S, AH32, AH36 50
Univerzalni trat
Bezrucova 300
735 93 Bohumín
Tel: +42 (0) 596 083 216 or +42(0) 596 082 881
email: martin.snapka@moravia-steel.cz Web www.moravia-steel.cz
The approved sections are in the form of universal flats nominal widths 150 to 550mm to the maximum thicknesses shown above.
Parent Company: TRINECKE ZELEZARNY a.s., Prumyslova 1000, 739 70 Trinec-Stare Metso.
Certificate ID No : MD00/2020.

List 1
VITKOVICE HEAVY MACHINERY a.s. Prague Steelmaking E.A.F. / Ingot As below

Ruska 2887/101
70602 Ostrava-Vitkovice
Tel: +420 595 95 6491 Mob: +420 724 135544
email: petr.vasicek@vitkovice.cz web: www.vitkovice.cz

Z - GROUP STEEL HOLDING A.S. Prague Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy 4
Division Železárny Hrádek,
Rokycanská 204,
338 42 Hrádek u Rokycan,
Tel: +420 474 644096 Fax: +420 474 642 288
Email mailto:stehlik.libor@steel-holding.cz
Web: www.steel-holding.cz
ZDAS, a.s. Prague Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy
Metallurgical Plant
59171 Zdár nad Sázavou
Tel: +420 566 643 998 Fax: +420 566 642 803
Email: mailto:antonin.tlusty@zdas.cz
Web:http://www.zdas.cz
Denmark
NLMK DANSTEEL A/S Copenhagen Plates Normal Strength E 60
A, B, D 100
Higher Strength EH32, EH36, EH36S 80
AH27S, AH32, AH36, DH27S, DH32, DH36 100
360FG, 410FG, 460FG, 490FG, 510FG 100
Havnevej 33
DK-3300 Frederiksværk
Tel: +45 477 82647 Fax: +45 477 70322 Email: mailto:zib@dansteel.dk Web:http://www.dansteel.dk
All grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.
Egypt, Arab Republic of

ABU ZAABAL ENGINEERING INDUSTRIES Cairo Plates Normal Strength A, B, D 100
Higher Strength AH27S 20
Hot and Cold Rolling mill (AZE)
Abu Zaabal
Inchas
Tel: +20 24469 1224 Fax: +20 24469 2608
Email: aze100@soficom.com.eg
Web www.azr.com
EGYPTIAN IRON & STEEL CO. Port Said Steelmaking B.O.S. / Con Cast As below
El Tebbin
Helwan
Cairo
Tel: +202 5940593 Fax +202 5011608
Email: mailto:eisc@idsc.net.eg
Web www.iron.steel.com.eg
Telex 20176 Tebbin

List 1
Finland
OUTOKUMPU STAINLESS OY Helsinki/Helsin Steelmaking E.A.F. / Con Cast As below
gfors
Plates Austenitic Stainless 304L, 316L, 321 12
Hot Rolled Coil Austenitic Stainless 304L, 316L, 321 12
Coil Austenitic Stainless 304L, 316L, 321 6
Terastie 1,
95490
Tornio
Tel No: +358 40 7675371 Fax no:+358 16 452 350
Email:susanna.siukonen@outokumpu.com
Web: http://www.outokumpu.com
OVAKO IMATRA OY AB Turku/Åbo Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms carbon, carbon-manganese, alloy 370
Bars Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36, 180
EH27S, EH32, EH36
Machinery alloy 180
Terästehtaantie 1
FI-55100 IMATRA
Tel: +358 5 680 21 Fax: +358 5 680 2211 Email: mailto:heikki.hurmola@ovako.com Web:http://www.ovako.com
Semi-finished products in carbon, carbon-manganese and alloy steel with fine grain (element combinations as stated), blooms to 370 mm section, to 6000mm
long for further processing to rolled products
MQS Approved - Approval No. MQS 020
RUUKKI METALS OY Turku/Åbo Steelmaking B.O.S. / Con Cast As below
Higher Strength FH27S, FH32, FH36 40
AH40, DH40, DH42, EH40, EH42 80
AH27S, AH32, AH36, DH27S, DH32, DH36, 150
EH27S, EH32, EH36
360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG, 100
510FG
Ferritic Low Temperature LTAH27S, LTAH32, LTAH36, LTDH27S, 40
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
EH27S, EH32, EH36
Raahe Steel Works
Rautaruukintie 155, PO Box 93
92101 Raahe
Tel +358 20 5911 Mob +358 40 54 90257 Fax +358 20 5923527 Email:mailto:lassi.myllykoski@ruukki.com Web: http://www.ruukki.com
Specified through thickness properties for up to 100 mm thickness.


List 1
France
AKERS FRANCE Lyon Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy
USINE DE THIONVILLE
Chemin du Leidt
B.P. 10200
57104 Thionville Cedex
Tel: +33 6 79 27 94 41 e mail: mailto:christophe.evrard@akersrolls.com web: http://www.akersrolls.com
APERAM Lyon Plates Austenitic Stainless 304L, 316L, 321, 304* 6
Gueugnon Plant BP 1
4 place des Forges
71130 Gueugnon
Tel: +33 3 85 85 78 56 Fax: +33 3 85 85 14 12 Mob: +33 609320872
Email: mailto:gerard.ramoissenet@aperam.com
Web: http://www.aperam.com
Certificate #: MD00/1582/0006/1 Expiry Date: 10/03/2017
APERAM ALLOYS IMPHY Lyon Steelmaking E.A.F. / Ingot As below
Plates Fe-Ni alloys Fe-36Ni* 8
Hot Rolled Coil Fe-Ni alloys Fe-36Ni* 1
Avenue Jean Jaurès
58160 IMPHY
Tel: +33 3 86 21 31 23 Fax: +33 3 86 21 31 07 Email:mailto:marie-paul.solignac@aperam.com Web:http://www.aperam.com
*Cold and hot rolled strip up to 8mm in INVAR/M93 grade (Fe-Ni36) accepted for approved applications; material greater than 1.5mm supplied in the As
Rolled condition; materials 1.5mm or less are supplied in the solution annealed condition.
ARCELORMITTAL Marseille Steelmaking B.O.S. / Con Cast As below
Higher Strength AH32, AH36, DH32, DH36, EH36 13
360AR, 410AR 16
Méditerranée Fos-sur-Mer
13776 Fos-Sur-Mer
CEDEX
Tel: +33 (0) 442 47 33 33 Fax +33 (0) 4 4247 31 00
Email: mailto: florence.sixdeniers@arcelormittal.com
Web: www.arcelormediterranee.com
ASCOMETAL Dunkerque Steelmaking E.A.F./Ingot/Con Cast As below
U1, U2 130
Usine de Dunes
BP 41
59941 Dunkerque
Cedex 2
Machinery grades up to 180 mm by continuous casting, 310 mm by ingot
Tel +33 32829 6203 Fax +33 32829 6003
ASCOMETAL Marseille Steelmaking E.A.F. / Ingot As below
Usine de Fos-sur-Mer
BP 30
13771 Fos-sur-Mer
Tel: +33 (0) 442 479 216 Fax: +33 (0) 442 051 511 Email : mailto:bruno.dadolle@ascometal.com
AUBERT & DUVAL Lyon Steelmaking E.A.F. / Ingot As below
Firminy Plant
BP 141
42704 FIRMINY CEDEX
Tel: +33 4 77 40 36 22 Fax: +33 4 77 40 36 99 Email mailto:alexandre.epailly@eramet-aubertduval.com Web: http://www.aubertduval.com
Ingots as semi-finished products to the above maximum weight; nominal; 1550/1730mm diameter x 2200mm; are approved for further processing for forgings.

List 1
CELSA FRANCE Bilbao Steelmaking B.O.S. / Con Cast As below

Semi-Finished Billets Normal Strength, Higher Strength 160
Rond-Point Claudius Magnin
64340 Boucau
Tel: +33 05 59 64 41 00 Fax: +33 05 59 64 41 21 email: nmelquiot@celsafrance.com Web: http://www.celsafrance.com
Billets as semi-finished products, nominal 160mm width and nominal 13300mm length to the above maximum thickness are approved for further processing for
rolled products.
GTS Industries Dunkerque Plates Normal Strength E 80
A, B, D 100
FH27S, FH32, FH36 50
AH27S, AH32, AH36, DH27S, DH32, DH36, 75
EH27S, EH32, EH36
360FG, 410FG 100
Port 3032
3032 Rue du Comte Jean - CS 56317
F-59379 Dunkerque Cedex 1
Tel: +33 (0)3 28 29 39 64 Fax: +33 (0)3 28 29 69 12 Email:mailto:philippe.nawracala@gts.dillinger.biz
Web: http://www.gts-dillinger.fr
Specified through thickness properties for all nornal and higher strength grade plates notation Z35 may be added.
INDUSTEEL FRANCE Lyon Steelmaking E.A.F. / Ingot carbon, carbon-manganese
Higher Strength FH32, FH36 50
AH32, AH36, DH32, DH36, EH32, EH36 400
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100
LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,
9Ni
ARCELOR MITTAL
Site de Chateauneuf
BP 368 - Chateauneuf
42803 RIVE DE GIER
Tel: +33 4 77 75 21 12 Fax: +33 4 77 75 20 03
Email: mailto:jean-philippe.baron@arcelormittal.com
Including plates with specified through thickness properties.

INDUSTEEL FRANCE, site du Creusot Lyon Steelmaking E.A.F. / Ingot As below
stainless
Porte du Breuil - BP 34
71201
71201 LE CRUUSOT CEDEX
Le Creusot Cedex
Tel No 33 3 8580 5575 Fax No. 33 3 8580 5211
Email: laetitia.billard@arcelormittal.com
Web: www.industeel.info
Certificate number MD00/3227/0001/1
Ingots also in martensitic stainless steel up to 40 T for approved applications
INDUSTEEL FRANCE, site du Creusot Lyon Plates Normal Strength A, B, D, E 150
AH32, AH36, DH32, DH36, EH32, EH36 150
Boiler & Pressure Vessel 360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100
LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,
9Ni
Austenitic Stainless 304L, 316L 50
56 rue Clemenceau - BP19
71201
Tel: +33 3 8580 5575 Fax: +33 3 8580 5211
Email: mailto:laetitia.billard@arcelormittal.com
Web: http://www.industeel.info
Plates with specified through thickness properties.
LAMINES MARCHANDS EUROPEENS Lyon Steelmaking B.O.S. / Con Cast As below
Bars Normal Strength A 30

List 1
2, Rue Emile Zola
59125 Trith St Léger
Tel +33 (0)3 2714 2270 Fax +33 (0)3 2714 2010 Email: mailto:e.cotton@lme.fr
LORRAINE TUBES Lyon Fabricated Sections Normal Strength A, B, D, E 16
100, rue du Maréchal Foch
54720 Lexy
Tel No: +33 382 252 252 Fax No: +33 382 252 116
Email: dmartini@lorraine.condesa.com
Web: www.condesa.com
Certificate No: MD00/4281/0001/ 1 Expiry Date: 17/01/2017
LORRAINE TUBES Lyon Fabricated Sections Normal Strength A, B, D, E 16
Route du Contez
57480 Rettel
Tel No: +33 382 252 225 Fax no: +33 382 252 116
Email: dmartini@lorraine.condesa.com
Web: www.condesa.com
Certificate No: MD00/4282/0001/1 Expirt Date 17/01/2014
UGITECH S.A. Lyon Steelmaking E.A.F./A.O.D./Con Cast As below
Semi-Finished Billets As below 205
Sections Austenitic Stainless 304L, 316L, 321 32
Bars Austenitic Stainless 304L, 316L, 321 130
Machinery austenitic stainless, duplex stainless, martensitic 95
stainless*
Avenue Paul Girod,
73403 UGINE Cedex
Tel: +33 4 79 89 32 92 Fax: +33 4 79 89 34 74 Email: mailto:laurent.prost@ugitech.com Web: http://www.ugitech.com
Certificate #: MD00/1583/0006/1 Expiry Date: 24/08/2014
Germany
ARCELORMITTAL BREMEN GmbH Bremerhaven Steelmaking B.O.S. / Con Cast As below
Boiler & Pressure Vessel 360, 410, 360FG, 410FG 20
Carl-Benz- Straße 30
D-28237 Bremen
Tel +49 421 648 2306 Fax +49 412 648 49 2306
email: salesflat.germany@arcelormittal.com web: www.arcelormittal.com/bremen

ARCELORMITTAL EISENHÜTTENSTADT GMBH Dortmund Steelmaking B.O.S. / Con Cast carbon, carbon-manganese
Werkstraße 1
D-15872 Eisenhüttenstadt
Tel +49 3364 3782 05 Fax +49 3364 3781 97
Email: mailto:frank.schadow@arcelormittal.com
Web http://www.arcelormittal-ehst.com
Continuously cast slab up to 250 mm thickness and cast bloom up to 300 mm thickness.
ARCELORMITTALAL RUHRORT GmbH Dortmund Steelmaking B.O.S. / Con Cast As below
Vohwinkelstraße 107
D-47137 Duisburg
Tel 0049 (0) 203 / 52 66 180 Fax 0049 (0) 203 / 606 66 332
email: hans-dieter.drippe@arcelormittal.com
Web http://www.arcelormittal.com
Aktiengesellschaft der Dillinger Hüttenwerke Hamburg Steelmaking B.O.S./Ingot/Con Cast As below
AH40, DH40, EH40, EH46S, FH46S 100
EH46, FH46 110
AH32, AH36, DH32, EH32 170
DH36, EH36 220
LTEH36, LTFH32, LTFH36, 5Ni

List 1
Hüttenwerkstrasse
Postfach 1580
D-66748 Dillingen / Saar
All plates with specified through thickness properties.
Tel: +49 6381 474735 Fax: +49 6831 473689

email: frank.schikofski@dillinger.biz web:: www.dillinger.de

BENTELER STEEL/TUBE GmbH Dortmund Steelmaking E.A.F. / Con Cast carbon, carbon-manganese, alloy
Blooms/Billets carbon, carbon-manganese, alloy 310
Niederdarmer Straße 5
D-49811 Lingen
Tel: +49 591 80004 800 Fax: +49 591 80004 460 Email to: gerd.lindenschmidt@benteler.de
Web: http://www.benteler.de
Steelmaking and semi-finished slabs, blooms and billets intended for plates, forgings and tubes.
Semi-finished products in carbon, carbon-manganese and alloy steel: slabs to 670mm wide, to 11,500mm long to 12.8 tonnes and blooms/billets of dimensions
300mm x 230mm or 310mm round of maximum length 12,800mm
BGH EDELSTAHL FREITAL GmbH Dortmund Steelmaking E.A.F./Ingot/Con Cast As below
Semi-Finished Ingots (tonnes) alloy, stainless steel, austenitic stainless, duplex 12
stainless
Slabs stainless steel 230
Billets As below 120
Bars Machinery alloy, austenitic stainless, duplex stainless, 165
martensitic stainless*
Am Stahlwerk 1
D-01705 Freital
Tel: +49 (0)351 646 2232 Fax: +49 (0)351 646 2888
Email: mailto:steffen.Rehberg@bgh.de
Web: http://www.bgh.de
Including forged bars
BGH EDELSTAHL SIEGEN GmbH Dortmund Steelmaking E.A.F./V.O.D./Ingot As below
Semi-Finished Ingots (tonnes) alloy, austenitic stainless, martensitic stainless 32
Industriestraße 9,
D-57076
Siegen
Tel No. +49 (0)271 701- 341 Fax No. +49 (0) 271 701- 300
Email peter.scheer@bgh.de
Web www.bgh.de
Certificate No MD00/3767/0003/1 Expiry date: 31/03/2016
BUDERUS EDELSTAHL GmbH Dortmund Steelmaking B.O.S. / Con Cast See notes
E.A.F. / Ingot carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F./V.O.D./Ingot Martensitic stainless*
Buderusstraße 25
D-35573 Wetzlar
Tel: +49 (0)6441 374 2505 Fax: +49 (0)6441 374 2681 Email: mailto:Lothar.schaefer@buderus-steel.com Web: http://www.buderus-steel.com
DEUTSCHE EDELSTAHLWERKE GMBH Dortmund Steelmaking E.A.F. / Con Cast As below
E.A.F. / Ingot As below
stainless
Machinery carbon, carbon-manganese, alloy, austenitic 80
stainless, duplex stainless, martensitic stainless*
Works Siegen
Obere Kaiserstraße
D-57078 Siegen
Tel: +49 (0)271 808 26 94 Fax: +49 (0)271 808 25 01 Email: mailto:andreas.prause@dew-stahl.com Web: http://www.dew-stahl.com
DEUTSCHE EDELSTAHLWERKE GMBH Dortmund Steelmaking E.A.F. / Con Cast As below
Semi-Finished Ingots (tonnes) carbon, carbon-manganese, alloy, stainless steel 66
Bars Semi-finished Products carbon, carbon-manganese, alloy, austenitic 250
stainless
Structural alloy, austenitic stainless 250
Machinery alloy, austenitic stainless, duplex stainless, 250

List 1
Works Witten
Auestraße 4
D-58452 Witten
Tel: +49 (0) 2302 292 437 Fax: +49 (0) 2302 294 008
email: stephanie.pueckel@dew-stahl.com web:www.dew-stahl.com
GEORGSMARIENHÜTTE GmbH Dortmund Steelmaking E.A.F./Ingot/Con Cast As below
Higher Strength AH32, AH36, DH32, DH36, EH32 180
Structural alloy 270
Chain Cable Stock U1, U2, U3, R3 155
Neue Hüttenstraße 1
D-49124 Georgsmarienhütte
Tel: +49 (0)5401 39 4630 Fax: +49 (0)5401 39 4598
Email: andre.rademacher@gmh.de
Web: http://www.gmh.de
H.E.S. HENNIGSDORFER ELEKTROSTAHLWERKE Dortmund Steelmaking E.A.F. / Con Cast As below
GmbH
Wolfgang-Küntscher-Straße 18
D-16761 Hennigsdorf
Tel: +49 (0)3302 806-0 Fax: +49 (0)3302 806-211 Email: mailto:labor.hes@rivagroup.com Web: http://www.rivagroup.com
HOESCH SCHWERTER PROFILE GmbH Dortmund Sections Normal Strength A 50
Eisenindustriestraße 1
D-58239 Schwerte
Tel: +49 (0)2304 106-340 Fax: +49 (0)2304 106-590
Email: mailto:info@tks-hho.thyssenkrupp.com
Web: http://www.hoesch-profile.de
Hüttenwerke Krupp Mannesmann GmbH Dortmund Steelmaking B.O.S. / Con Cast carbon, carbon-manganese, alloy
Huckingen Works
Ehinger Strasse 200
D-47259 Duisburg-Huckingen
Tel: +49 (0)203 999-01 Fax: +49 (0)203 999-4411 Email: mailto:michael.ninnemann@hkm.de Web: http://www.hkm.de
ILSENBURGER GROBBLECH GmbH Dortmund Plates Normal Strength B, D, E 85
A 150
AH27S, AH32, AH36, DH27S, DH32, DH36, 120
EH27S, EH32, EH36, FH27S, FH32, FH36
360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG, 100
510FG
Ferritic Low Temperature LTAH40, LTDH40, LTEH40, 1.5Ni, 3.5Ni, 5Ni, 50
9Ni
Austenitic Stainless 316L 80
Veckenstedter Weg
D-38871 Ilsenburg
Tel: +49 39452/85 5530 Fax: +49 39452/85 5733

email Manegold@ilsenburger-Grobblech.de web: www.ilsenburger-Grobblech.de

Lech-Stahlwerke GmbH Hamburg Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms/Billets As below 240
Industriestrasse 1
D-86405 Meitingen
Tel: +49 (0) 8271/82-325 Fax: +49 (0) 8271/82-405 Email:mailto:christian.herrmann@lech-stahlwerke.de Web: http://www.lech-stahlwerke.de

List 1
PEINER TRÄGER GMBH Dortmund Steelmaking E.A.F. / Con Cast As below

Sections Normal Strength A, B, D, E 40
Gerhard-Lucas-Meyer Str. 10
D-31226 Peine
Tel: +49 5171 91 9321 Fax: +49 5171 91 9373
email: Schernich.O@salzgitter-ag.de web: www.peinertraeger.de
REINER BRACH GmbH & Co. KG Bremen Plates Normal Strength A, B, D, E 250
AH27S, DH27S, EH27S 250
360FG, 410FG 150
Wilhelm-Karmann-Straße 5
D-28237 Bremen
Tel: +49 421 985 08-140 Fax: +49 421 985 08-149
Email mailto:frank-santuari@brach.de
Web:http://www.brach.de
REINER BRACH GmbH & Co. KG Bremen Semi-Finished Ingots (tonnes) carbon, carbon-manganese 43
Betriebsstätte Eisenhüttenstadt
Werkstraße,16
D-15890 Eisenhüttenstadt
Tel No +49 3364 37 81 54 Fax No +49 3364 37 81 55
Email: info@brach.de
Web: www.brach.de
Certificate No. MD00/4032/0001/1 Expiry Date 08/06/2015
SAARSCHMIEDE GmbH FREIFORMSCHMIEDE Hamburg Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese 56
Bismarckstraße 57-59
D-66330 Völklingen
Tel:+49 (0)6898 102650 Fax:+49(0)6898 104560
Email:mailto: m.lorinser@saarschmiede.com
Web:http://www.saarschmiede.com
SAARSTAHL AG Hamburg Bars Normal Strength A 40
Works Neunkirchen
D-66511 Neunkirchen
Tel: +49 6821 168644 Fax: +49 6898 1054293 Email: mailto:hanswerner.muller@saarstahl.com Web:http://www.saarstahl.com
SAARSTAHL AG Hamburg Steelmaking B.O.S. / Con Cast As below
Semi-Finished Blooms/Billets Normal Strength 265
Works Völklingen
Bismarckstrasse 57 - 59
D-66330 Völklingen
Tel: +49 (0) 6898 104 293 Fax: +49 (0) 6898 105 4293 Email: mailto:mark.bleymehl@saarstahl.com Web:http://www.saarstahl.com
SALZGITTER FLACHSTAHL GmbH Dortmund Steelmaking B.O.S. / Con Cast As below
D-38239 Salzgitter,
Eisenhüttenstrasse 99,
Tel: +49 5341 21-3196 Fax: +49 5341 21-2008
Email: KoerferG@salzgitter-ag.com
Web: www.salzgitter-flachstahl.de
Approved slab section sizes up to 350 x 2600mm.
Steel types carbon and carbon-manganese cover the supply of slabs for processing into normal strength, high strength, boiler and pressure vessel grades and
ferritic steels for low temperature service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final
processing mill is responsible for ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical
properties.
SALZGITTER MANNESMANN GROBBLECH GmbH Dortmund Plates Normal Strength A, B, D, E 50
EH27S, EH32, EH36
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50
Wiesenstraße 36
D-45473 Mülheim an der Ruhr
Tel: +49 (0)208 458 458 4510 Fax: +49 (0)208 458 1872 Email: mailto:info.service@smgb.de Web: http://www.smgb.de

List 1
SCHMIEDEWERKE GRÖDITZ GmbH Dortmund Steelmaking E.A.F. / Ingot As below

stainless
Riesaer Straße 1
D-01609 Gröditz
Tel: +49 35 263 62-613 Fax: +49 35 263 62-622
email: thomas-jakubowski@stahl-groeditz.de web: www.stahl-groeditz.de
Including ESR ingot and the supply of liquid steel to Stahlguss Groditz GmbH.
SILBITZ GUSS GmbH Dortmund Steelmaking E.A.F./V.O.D./Ingot As below
Semi-Finished Ingots (tonnes) duplex stainless 7
Dr. - Maruschky- Straße 2
D-07613 Silbitz/Thüringen
Tel: +49 (0)3 6693 80-250 Fax: +49 (0)3 6693 80251
email: mailto: jfriede@silbitz-guss.de web: www.silbitz-guss.de
Ingot approval covers duplex and superduplex grades.

STAHLWERK BOUS GMBH Hamburg Steelmaking E.A.F./Ingot/Con Cast carbon, carbon-manganese, alloy
P/O Box 1243
D-66359 Bous/Saar
Tel: +49 6834 81286 Fax: +49 6834 81586 Email: mailto:mmuth@stahlwerk-bous.de Web http://www.stahlwerk-bous.de
Ingots up to 60 tonne and 2300 mm dia.
Con cast billets approved to 430 x 320mm.

STAHLWERK THÜRINGEN GMBH Dortmund Steelmaking E.A.F. / Con Cast As below
Kronacher Straße 6
D-07333 Unterwellenborn
Tel +49 3671 455006010 Fax +49 3671 45507710
Email: mailto:gerd.hoffmann@stahlwerk-thuringen.de
Web http://www.stahlwerk-thueringen.de
Schmidt + Clemens GmbH +Co. KG Dortmund Steelmaking E.A.F. / Ingot As below
stainless
Kaiserau 2
D-51789 Lindlar
Tel: +49 (0)22 66 9230 Fax: +49 (0)22 66 928230
Email: mailto:g.bach@schmidt-clemens.de
Web http://www.schmidt-clemens.de
THYSSENKRUPP STEEL EUROPE AG Dortmund Hot Rolled Coil Normal Strength A, B, D, E 20
Plates from coils Normal Strength A, B, D, E 20
Boiler and Pressure Vessel 410 FG, 460 FG, 360 FG, 360, 410, 490FG, 510FG 20
Works Bochum
Kaiser-Wilhelm-Straße 100
D-47166 Duisburg
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:roland.riesbeck@thyssenkrupp.com Web: http://www.thyssenkrupp-stahl.com
THYSSENKRUPP STEEL EUROPE AG Dortmund Steelmaking B.O.S. / Con Cast As below
Works Beeckerwerth
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:joachim.gottlieb@thyssenkrupp.com Web: http://www.thyssenkrupp-stahl.com
THYSSENKRUPP STEEL EUROPE AG Dortmund Steelmaking B.O.S. / Con Cast As below
Works Bruckhausen
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587
Email: mailto:joachim.gottlieb@thyssenkrupp.com
Web: http://www.thyssenkrupp-stahl.com

List 1
THYSSENKRUPP STEEL EUROPE AG Dortmund Plates Normal Strength A, B, D, E 150

AH40, DH40, EH40 60
AH27S, AH32, AH36, DH27S, DH32, DH36, 100
EH27S, EH32, EH36
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100
Plates from coils Normal Strength A, B, D, E 20
Higher Strength AH27S, DH27S, AH32, DH32, AH36, DH36, 20
EH27S, EH32, EH36
Boiler and Pressure Vessel 360 FG, 460 FG, 410 FG, 360, 410, 490FG, 510FG 20
Works Duisburg-Süd
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:joachim.gottlieb@thyssenkrupp.com Web: http://www.thyssenkrupp-stahl.com
Specified through thickness properties on all normal and higher strength steel grade plates.
ThyssenKrupp Nirosta GmbH Dortmund Steelmaking E.A.F./Ingot/Con Cast As below
Slabs austenitic stainless 240
Works Krefeld
Oberschlesienstraße 16
D-47807 Krefeld
Tel: +49 (0) 211 7107 562 Fax: +49 (0) 211 7107 376 Email: mailto:thomas.seifert@thyssenkrupp.com Web: http://www.thyssenkrupp.com
Ingots as semi finished products nominal dimensions 1700 x 690xmm & nominal height 2600mm to the above maximum weight and slabs as semi finished
products nominal width 1500mm & nominal length 10000mm, are approved for further processing for rolled products.
India
ARCVAC FORGECAST LTD Calcutta Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy
12C, Lord Sinha Road,
Post Box: 9210
Kolkata: 700071
West Bengal
Tel: + 91 33 2600 2176; Fax + 91 33 2659 8002
Email: swapan@smithy.in
Web: www. arcvacsteel.com
BHUSHAN POWER & STEEL LIMITED Calcutta Steelmaking E.A.F. / Con Cast As below
Vill. Thelkoli, P.O. Lapanga,
Tehsil - Rengoli,
Distt. Sambalpur - 768 232,
Tel: +91 663 253 5000 / 256 2026-32 Fax: +91 663 256 2007 / 256 2011 Email: Orissa@bpsl.net Web: http://www.bpsl.net
Billets as semi-finished products nominal 200mm maximum width x nominal 12000mm maximum length are approved for further processing for rolled
products.
Bars for Grades U1 and U2 accepted for end use in the normalised condition; bars for Grade U3 accepted for end use in the quenched and tempered condition.
Certificate Number: MD00/xxxx/0001/1 Expiry: 10/06/2016
ESSAR STEEL INDIA LTD. Mumbai Steelmaking E.A.F. / Con Cast As below
Hot Strip Mill
Hazira - 394270
District Surat
Gujarat
Tel: +91 261 6683139 Fax: +91 261 6683747 Email mailto:sravinarayana.bhat@essar.com Web http://www.essar.com
Slabs as semi finished products nominal maximum width 2040mm x nominal maximum length 4900mm to the above maximum thickness are approved for
ESSAR STEEL INDIA LTD. Mumbai Plates Normal Strength E 70
A, B, D 100
EH27S, EH32, EH36

List 1
Plate Mill Division
Tel: +91 261 668 3291 or 6739 Fax: +91 261 668 3747 Email mailto:sravinarayana.bhat@essar.com or rudrapatnam.balasubramaniam@essar.com Web
http://www.essar.com
All plates are restricted to a maximum width of 4550mm.
ISMT LIMITED (STEEL PLANT) Pune Steelmaking E.A.F. / Con Cast carbon, carbon-manganese, alloy
Morgaon Road
Jejuri 412 303
Purandara, Pune
Maharashtra
Tel: +91-020-414 34100 Fax: +91-020-26630779
Email mailto: ln.hegde@ismt.co.in
Web http://www.ismt.com
Certificate number. MD00/3816/0002/1 Expiry date: 23/08/2016
JINDAL STAINLESS LIMITED Yamunanagar Steelmaking E.A.F./A.O.D./Con Cast austenitic stainless

E.A.F./V.O.D./Con Cast austenitic stainless
Plates Austenitic Stainless 304L, 316L, 317L, 321, 347 53
Post Box No. 6
O.P. Jindal Marg
Hisar Haryana State
India Pin 125 005
Tel: +91 98960 95029
email: hsr.maheshwari@jslhsr.com web: www.jslstainless.com
JINDAL STEEL & POWER LIMITED New Delhi Steelmaking B.O.S./E.A.F./Con Cast As Below
Boiler & Pressure Vessel 360AR, 410AR, 460AR, 360, 410, 460, 490, 80
360FG, 410FG, 460FG, 490FG
Raigarh
Post Box No.16
Kharsia Road
Raigarh 496001 Chattisgarh
Tel: +91 7762 227001 10 Fax: +91 7762 227021/22 Email to rksaini@jspl.com
KALYANI CARPENTER SPECIAL STEELS LTD. Mumbai Steelmaking E.A.F./Ingot/Con Cast As below
Mundhwa
Pune 411 036
Maharashtra
Tel: +91 20 6621 5000 Fax: +91 20 2682 4483 Email: mailto:nitinbhat@kcssl.com Web: http://www.kalyanicarpenter.com
Ingots as semi-finished products to the above maximum weight nominal 540/700mm diameter x 1770mm long 540/700 and blooms to the above maximum
thickness nominal 400mm wide x 10,000mm long are accepted for further processing for rolled products.
MAHINDRA SANYO SPECIAL STEEL PVT. LTD. Mumbai Steelmaking E.A.F. / Ingot As below
stainless
Blooms/Billets carbon, carbon-manganese, alloy, austenitic 260
stainless steel
Khopoli Works
Jagdish Nagar
Khopoli
Dist. Raigad
Maharashtra 410 216
Tel: +91 952192 263318 (263347) Fax: +91 952192 263582 (263076)
Email mailto:sarkar.samar@mahindra.com
Web www.mahindra.com
STEEL AUTHORITY OF INDIA LTD. Bhilai Steelmaking B.O.S. / Con Cast As below
EH27S, EH32, EH36
360AR, 410AR, 360, 410 63
360FG, 410FG 75

List 1
Bhilai Steel Plant
Bhilai 490 001
Chhattisgarh
Tel +91 940 7981686 Fax +91 788 2222040 Email:mailto:gcdas@sail-bhilaisteel.com
STEEL AUTHORITY OF INDIA LTD. Calcutta Steelmaking B.O.S. / Con Cast As below
360AR, 410AR 40
Rourkela Steel Plant
Rourkela 769 011
Orissa
Tel: +91 (0) 661 244 7424 Fax +91 (0) 661 251 0183 email: sc.prasad@sailrsp.co.in Web: http://www.sail.co.in
TATA STEEL LIMITED Calcutta Steelmaking B.O.S. / Con Cast As below
43 Chowringhee Road
Kolkata 700 071
Tel: +91 (33) 22889251 Fax: +91 (33) 22887255/22881396 Email mailto:rakesh@itd.tatasteel.com Web http://www.tata.com
Certificate No. MD00/1489/0006/1 Expiry date:15/02/2015
U.P. STEELS New Delhi Steelmaking E.A.F. / Ingot alloy
A Unit of ISGEC Heavy Engineering Limited
Nara
Meerut Road,
Muzaffarnagar - 251 203
Uttar Pradesh
Tel +91 1396 252404/5/6 Fax + 91 1396 252324
Email: qc@upsteels.com
Web: www.upsteels.com
VIRAJ PROFILES LIMITED (SMS DIVISION) Mumbai Steelmaking IF/AOD/Ingot/ConCast austenitic stainless steel
Semi-Finished Blooms/Billets austenitic stainless steel 300
G-2 / G23 MIDC, Tarapur Industrial Area,
Boisar, Taluka - Palghar, Dist. Thane,
Maharashtra - 401506,
Tel: +91 2525 261514 Fax: +91 2525 260159 Email mailto:quality@viraj.com Web: http://www.viraj.com
Billets and blooms as semi-finished products to the above maximum thickness, nominal 300mm wide x nominal 9000mm long are approved for further
processing for forged products.
Indonesia
PT. GUNAWAN DIANJAYA STEEL Tbk Jakarta Plates Normal Strength B, D 25
A 40
Jl. Margomulyo No. 29A
Greges-Asemrowo
Surabaya 60183
Tel: +62 31 7490598 Fax: +62 31 7490581/7482109
Email: mailto:gunawan@gds.co.id Web http://www.gunawansteel.com
PT. GUNUNG RAJA PAKSI Jakarta Plates Normal Strength A, B 50
JI. Imam Bonjol 4, Warung Bongkok
Desa Sukadanau, Clkarang Barat, Bekasi
West Java, Indonesia
Tel: +62 21 8900111 ext 3518 Fax: +62 21 8900333
Email: mailto:dewi.pl@grdsteel.com
Web: http://www.grdsteel.com
PT. JAYA PARI STEEL Tbk. Surabaya Plates Normal Strength A, B 25
Jl Margomulyo No. 4
Tandes
Surabaya 80186
Tel: +62 31 7491288 Fax:+62 31 7491714 Email:mailto:jayapari@red.net.id

List 1
PT. KRAKATAU STEEL (PERSERO) TBK. Jakarta Steelmaking E.A.F. / Con Cast As below
Plates from coils Normal Strength A 25
Divisi QP & MS (QA)
Jl. Industri No. 5
PO. Box 14
Cilegon 42435
Tel: +62 (0) 254 317274 Fax: +62 (0) 254 372608 Email: mailto:handritoi.bharata@krakatausteel.com Web: http://www.krakatausteel.com
Plates and coils in the supply condition TM+Acc Fine Grain Al+Nb are restricted to the thickness range 16.0 to 25.0mm.
Slabs as semi-finished products nominal maximum width 2000mm x and nominal maximum length 12000 mm to the above maximum thickness are approved
for further processing for rolled products.
Italy
A.B.S. Acciaierie Bertoli Safau S.p.A. Trieste Steelmaking E.A.F./Ingot/Con Cast As below
Semi-Finished Rolled Bars Carbon, Carbon manganese, Alloy 370
As Cast Round Section Carbon, Carbon-manganese, Alloy 700
Rolled Square Bars Carbon, Carbon-manganese, Alloy 420
Via Buttrio, 28
33050 Pozzuolo del Friuli (UD)
Tel: +39 (0) 432 613 211 Fax: +39 (0) 432 613 249 E-mail: mailto:m.graffi@absacciai.it Web: http://www.absacciai.it
ACCIAIERIA FONDERIA CIVIDALE S.P.A. Trieste Steelmaking E.A.F. / Ingot As below, carbon, carbon-manganese, alloy
Via delle Industrie No. 40
Zona Industriale
33043 Cividale del Friuli
(Udine)
Tel +39 432 706922 Fax +39 432 706920
email: afcspa@afcspa.com web www.cividalespa.com
Steel types carbon, carbon-manganese and alloy cover the supply of ingots for processing into forgings according to the Society's Rules for the Manufacture,
Testing and Certification of Materials, Chapter 5. The final processing mill is responsible for ordering steel which complies with their approved chemical
composition and enables them to achieve the required mechanical properties
ACCIAIERIE VALBRUNA S.P.A. Venice Steelmaking E.A.F./Ingot/Con Cast As below
Billets carbon, carbon-manganese, alloy, austenitic 220
Bars Machinery austenitic stainless, precipitation hardened 155
stainless*, martensitic stainless*
duplex stainless 205
Viale Della Scienza, 25 z.i.
36100 Vicenza
Tel: +39 0444 968211 Fax: +39 0444 968182 Email:mailto:quality@valbruna.it Web:http://www.acciaierie-valbruna.com
* Accepted for approved applications
Approval for Precipitation Hardened Stainless Machinery Bar is for Grade 17.4 PH, approval for Martensitic Stainless Machinery Bar is for Grade 431 and
Grade 1.4418 Quenched and Tempered.
Duplex Stainless Steel bars are not approved for use in welded construction, and weld repair is not permitted.
Approval of Con cast material is for the production of Austenitic Stainless Steels only.
Ingots as semi finished products nominal maximum dimensions 600mm x 530mm x 2060mm to the above maximum weight are accepted for further processing
for rolled products and forgings.
Billets as semi finished products nominal maximum width 220mm x nominal maximum length 6500mm to the above maximum thickness are accepted for
further processing for rolled products and forgings.
ACCIAIERIE VALBRUNA S.P.A. Venice Steelmaking E.A.F./Ingot/Con Cast As below
A.O.D./Ingot/Con Cast as below
Bars Machinery austenitic stainless, duplex stainless, 73
precipitation hardened stainless*, martensitic
stainless*
Via A Volta 4
39100 Bolzano
39100 Bolzano
* Accepted for approved applications
Tel; +39 (0)471 924111 Fax: +39 (0)471 924355
Email: mailto:info@valbruna.it Web: http//www.acciaierie-valbruna.it

List 1
ACCIAIERIE VENETE S.p.A. Venice Steelmaking E.A.F. / Con Cast carbon, carbon-manganese, alloy
Semi-Finished Blooms/Billets carbon, carbon manganese, Alloy 280
Camin Works
Riviera Francia, 9
35020 Camin (Padova)
Tel +39 (0)49 8282 820 Fax +39 (0)49 8282 666 Email: mailto:commercial.dep@acciaierievenete.com Web: http://www.acciaierievenete.com
Approval does not cover bars with a diameter of less than 65mm.
AFV ACCIAIERIE BELTRAME S.p.A. Venice Steelmaking E.A.F. / Con Cast As below
Viale della Scienza 81/A
36100 Vicenza
Tel +39 0444 967111 Fax +39 0444 967137
Email: mailto:info@beltrame.it
Web site http://www.beltrame.it
AFV ACCIAIERIE BELTRAME S.p.A. Venice Bars Normal Strength A, B, D, E 40
Stabilimento di Marghera
Via del Commercio, 15
30175 Marghera (VE)
Tel +39 041 2583711 Fax +39 041 2583819
E-mail:mailto:info@beltrame.it
Web www.beltame.it
Certificate No. MD00/1374/0006/1 Expiry date: 09/02/2015 *Enhanced Survey*
ARMANDO CIMOLAI CENTRO SERVIZI Srl Trieste Fabricated Sections Normal Strength A, B, D 22
Via Masieres, No.32
33080 San Quirino (PN)
Tel: +39 (0)434 919292 Fax: +39 (0)434 919266
Email: accs_sanquirino@comolai.com
ASA S.r.l. Ravenna Fabricated Sections Normal Strength A 25
Via Gaiano,33
60027 Osimo (AN)
Tel No: +39 071 7131407 Fax No: +39 071 7132745
Email info@asabugatti.it
Web www.asabugatti.it
ASO SIDERURGICA S.r.L. Brescia Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy
Unipersonale
Via Seriola no. 122
25035 Ospitaletto
Brescia
Tel: +39 (0)30 6841011-(0)30 6841165 Fax: +39 (0)30 6841012 Email: mailto:Info@aso.it Web: http://www.aso.it
COGNE ACCIAI SPECIALI S.p.a Milan Steelmaking E.A.F. / Con Cast austenitic stainless, duplex stainless
E.A.F. / Ingot martensitic stainless*
Semi-Finished Ingots (tonnes) austenitic stainless, duplex stainless 4
Billets Martensitic Stainless Steel* 160
austenitic stainless, duplex stainless 270
Bars Martensitic Stainless Steel* 220
Via Paravera,16
11100 AOSTA
Tel No: +39 165 3021 Fax no: +39 165 43779
Email: info@cogne.com
Web site: www.cogne.com
Certificate No.MD00/3809/0002/1 Expiry date 13/07/2016
EVRAZ PALINI E BERTOLI S.P.A. Trieste Plates Normal Strength A 30
Via E. Fermi, 28 - 33058
San Giorgio di Nogaro (UD)
Tel: +39 0431 62 3111 Fax: +39 0431 62 1244
Email: info@paliniebertoli.it web:
www.paliniebertoli.it

List 1
FOMAS S.p.A. Milan ESR Ingots carbon, carbon-manganese, alloy, austenitic 125
stainless, duplex
Via Martiri della Liberazione, 17
23875 Osnago (LC)
Tel No +39 3999811 Fax No +39 3958487
Email: sparma@fomas.it
Web www.fomas.it
Certificate No MD00/0475/0003/1 Expiry 09/01/2016
G. BAGLIETTO S.a.s. NAVAL STEEL Genoa Fabricated Sections Normal Strength A 20
Via Castelgazzo 11
Novi Ligure (AL)
Certificate No. MD00/3910/0001/1 Expiry date: 16.05.2014
ILVA S.p.A. Palermo Steelmaking B.O.S. / Con Cast As below
EH27S, EH32, EH36
Taranto Works
Via Appia KM 648
Taranto 74100
Tel: +39 02 307 00 775 Fax: +39 02 307 00 285
Email: mailto:commerciale.lamiere@rivagroup.com
Web: http://www.rivagroup.com
Specified through thickness properties for grade D, E, AH, DH and EH notation Z35 may be added
LUCCHINI RS S.p.A. Brescia Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy, austenitic
stainless
Via G. Paglia N.45
24065 Lovere
Bergamo
Tel: +39 035 963535 Fax: +39 035 963488 Email: mailto:s.cantini@lucchiniRS.it Web: http://www.lucchiniRS.it
METINVEST TRAMETAL S.p.A. Trieste Plates Normal Strength A, B, D, E 60
EH27S, EH32, EH36
Via Enrico Fermi, 44
33058 San Giorgio di Nogaro (UD)
Approved for Z grade plates with specified through thickness properties when tested in accordance with Rules requirements.
Tel: +39 010 57 62911 Fax: +39 010 57 62990 Email:mailto:rre@trametal.it Web:http://www.trametal.it
NLMK VERONA Venice Steelmaking E.A.F. / Ingot As below
Via A, Salieri, 22,
37050 Vallese di Oppeano (Verona)
Tel: +39 045 699 7900 Fax: +39 045 699 7901 email: verona@eu.nlmk.com Web: http://www.eu.nlmk.com/verona/
Ingots as semi finished products are approved for further processing for forgings to the above maximum weight. Round and Polygon ingots to nominal
maximum dimensions of 1200mm diameter x 4750mm length, oblong ingots to nominal maximum dimensions 970mm x 870mm x 2050mm.
Certificate Number MD00/3985/0001/1 Expiry date: 31/01/2015
NUNKI STEEL SPA Venice Steelmaking EAF/LRF/VD/Ingot Carbon, Carbon-manganese, Alloy 40
E.Fermi 33,
33058 San Giorgio Di Nogaro (UD),
Tel: 00 39 (0)431621227 Fax: 00 39 (0)431622438
Certificate No.:MD00/40870001/1 Expiry Date: 06/11/2015
OFFICINE NORD EST S.r.l Trieste Fabricated Sections Normal Strength A, B, D, E 50
Via Ungaresca No.12
33080 San Quirino (Pn)
Tel: +39 (0)434 919091 Fax: +39 (0)434 918646 Email to: info@officinenordest.it
OLIFER-ACP S.P.A. Brescia Sections Normal Strength A, B, D 10
ROLLING MILL - ODOLO
Brescia Work
Loc.Motta Alta, 14
24050 Cividate Al Piano
Bergamo
Tel +39 365 826088 Fax +39 365 860727 Email: mailto:olifer@mail.olifer.com Web:http://www.olifer.com

List 1
OLIFER-ACP S.P.A. Brescia Steelmaking E.A.F./Ingot/Con Cast As below

STEELMAKING
Bergamo Works
Loc. Motta Alta 14
Cividate Al Piano
Tel: +39 363 97193/4 Fax: +39 363 976666
Email: mailto:direzione-cividate@olifer.com
Web http://www.olifer.com
PALESCANDOLO SPA Naples Fabricated Sections Normal Strength A 25
Via Boscofangone, zone A.S.I., Nola
Tel. no. +39 0817340800; Fax. no.: +39 0817340454 Email: ppalesc@tin.it; web: www.palescandolo.it
RUBIERA SPECIAL STEEL S.p.A. Venice Steelmaking E.A.F./Ingot/Con Cast As below
Semi-Finished Ingots (tonnes) carbon, carbon-manganese, alloy, Normal 100
Strength, Higher Strength
Bars carbon, carbon-manganese, alloy, Normal 180
Strength, Highrer Strength
Via 25 Aprile, 64
42013 Casalgrande (RE)
Tel: +39 0522 997209 Fax: +39 0522 840040 Email: mailto:commerciale@acciaieriadirubiera.it Web http://www.acciaieriadirubiera.com
Address for orders: Rubiera Special Steel S.p.A. , Via San Cataldo, 115, 41100 Modena, Italy.
Ingots as semi finished products nominal maximum diameter 1935mm x nominal maximum height 5250mm to the above maximum weight in normal strength
and higher strength grades are approved for further processing for rolled products and in carbon, carbon-manganese & alloy grades are approved for further
processing for forgings.
Bars as semi finished products nominal maximum length 9500mm to the above maximum thickness in normal strength and higher strength grades are approved
for further processing for rolled products and in carbon, carbon-manganese & alloy grades are approved for further processing for forgings.
SIDERVAL S.P.A. Milan Sections Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36, 30
EH27S, EH32, EH36
Via Roma 39C
23018 Talamona
Sondrio
Tel: +39 342 674125 Fax: +39 342 670400 Email: mailto:siderval@siderval.it Web: http://www.siderval.it
Japan
AICHI STEEL CORPORATION Kobe Steelmaking E.A.F. / Ingot carbon, carbon-manganese, austenitic stainless
Semi-Finished Bars alloy 190
Machinery carbon, carbon-manganese, alloy, austenitic 125
stainless
Chita Plant
1, Wano-Wari
Arao-machi
Tokai-shi
Aichi-ken, 476-8666
Tel: +81 52 603 9353 Fax: +81 52 603 9898
Email: mailto:nagayama@he.aichi-steel.co.jp
Web: www.aichi-steel.co.jp
AICHI STEEL CORPORATION Kobe Bars Austenitic Stainless 304L, 316L 150
Kariya Plant
3-6, Toyota-cho
Kariya-shi
Aichi-ken
448-0848
Tel +81 566 21 9130 Fax +81 566 23 6925
Email: mailto:hiroaki.k@he.aichi-steel.co.jp
Web www. aichi-steel.co.jp
CHUBU STEEL PLATE CO., LTD. Kobe Steelmaking E.A.F. / Con Cast As below
5-1, Kousudori
Nakagawa-ku
Nagoya
Tel: +81 52 661 3818 Fax: +81 52 661 2265 Email: mailto:aki-onozato@chubukohan.co.jp Web http://www.chubukokan.co.jp

List 1
DAIDO STEEL CO., LTD. Kobe Steelmaking E.A.F. / Ingot As below

Chita Plant
39, Motohama-machi
Tokai-shi
Aichi-ken
Tel: +81 562 33 3106 Fax: +81 562 33 6598
Email:h-fujita@ac.daido.co.jp
Web: http://www.daido.co.jp
DAIDO STEEL CO., LTD. Yokohama Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy
Shibukawa Plant
500, Ishihara
Shibukawa-shi
Gunma 377-0007
Tel: +81 279 25 2009 Fax: +81 279 25 2043 Email: mailto:t-furuse@ac.daido.co.jp
GODO STEEL LTD. Kobe Steelmaking E.A.F. / Con Cast As below
U1, U2 150
2946 Nakashima Shikamaku
Himeji-city
Hyogo pref.
Tel. +81 (0)792 34 9332 Fax +81(0)792 34 9538
HITACHI METALS, LTD. Kobe Steelmaking E.A.F. / Ingot As below
Structural alloy, austenitic stainless 150
Yasugi Works
2107-2, Yasugi-cho
Yasugi-shi
Shimane-ken
Tel: +81 (0) 854 22 1908 Fax: +81 (0)854 23 0281 Email mailto:hitoshi.iwata@hitachi-metals.co.jp Web http://www.hitachi-metals.co.jp
JFE BARS & SHAPES CORPORATION Kobe Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms Normal Strength, Higher Strength 300
Billets Normal Strength, Higher Strength 150
Sections Normal Strength B, D, E 25
A 32
Higher Strength EH32, EH36 25
AH32, AH36, DH32, DH36 32
Himeji Works
1280, Hosoe,
Shikama-ku, Himeji-City,
Hyogo-Pref. 672-8064,
Tel +81 (0)792 35 6376 Fax +81 (0)792 35 2048 email: mailto:masanobu-kimura@jfe-bs.co.jp Web: http://www.jfe-bs.co.jp
The scope of approval for semi-finished products includes for; billets nominal maximum width 150mm x nominal maximum length 8600mm; blooms nominal
maximum widths 220mm x nominal maximum length 10.000mm; approved for further processing for rolled products.
JFE BARS & SHAPES CORPORATION Yokohama Steelmaking E.A.F. / Con Cast As below
Kashima Works
7 Minamihama, Kamisu-city
Ibaraki Pref.
314-0111
Tel: +81 (0)299 90 5218 Fax: +81 (0)299 90 5201 Mob +81(0) 9050905201
Email: mailto:yuichiro-nishidate@jjfe-bs.co.jp
Web http://jfe-bs.co.jp
Semi finished products as billets to nominal 150mm width and 12000mm nominal length to the maximum thickness shown above are approved for further
processing for rolled products.
JFE STEEL CORPORATION Kobe Steelmaking B.O.S. / Con Cast As below

List 1
Japan
JFE STEEL CORPORATION Kobe Plates Higher Strength AH42, FH27S, FH32, FH36 50
DH42, DH46, DH50, DH55, DH62, DH69, EH42, 75
EH46, EH50, EH55, EH62, EH69
AH40, DH40, EH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36, 150
EH27S, EH32, EH36
360, 410 100
360FG, 410FG, 460FG, 490FG, 510FG 134
Ferritic Low Temperature 9Ni 40
Clad E/304L, E/316L 30
Tapered A, B, D, AH27S, AH32, AH36, DH27S, DH32, 50
DH36, EH27S, EH32, EH36
Differential Thickness A, B, D, AH27S, AH32, DH27S, DH32 40
EH27S, EH32, EH36
Machinery alloy 165
carbon-manganese 190
West Japan Works (Kurashiki)
1 Mizushima
Kawasaki-Dori
Kurashiki
Tel: +81 (0)86 447 2652 Fax: +81 (0)86 447 2735 Email: mailto:y-kida@jfe-steel.co.jp
Specified through thickness properties on all plate grades.

JFE STEEL CORPORATION Kobe Steelmaking B.O.S. / Con Cast As below
Semi-Finished Slabs carbon, carbon-manganese, Normal strength, 300
Higher Strength
Blooms/Billets carbon, carbon-manganese, Normal Strength, 250
Higher Strength
Higher Strength FH27S, FH32, FH36, FH40 80
EH47 85
AH27S, AH32, AH36, AH40, DH27S, DH32, 100
DH36, DH40, EH27S, EH32, EH36, EH40
460FG, 490FG, 510FG 55
360FG, 410FG 70
Ferritic Low Temperature LTAH27S, LTAH32, LTAH36, LTAH40, 40
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36
Austenitic Stainless 304L, 304LN, 316L, 316LN, 317L, 317LN 55
Clad A to EH36/304L, A to EH36/316L 30
Differential Thickness A, DH34S, B, D, A,B, AH32, AH36, DH32, 50
DH36, AH34S
360, 410, 360FG, 410FG 12
Sections Normal Strength E 18
A, B, D 35
Higher Strength AH40, DH40, EH40, FH27S, FH32, FH36 18
AH27S, AH32, AH36, DH27S, DH32, DH36, 36
EH27S, EH32, EH36
LTFH32, LTFH36

List 1
West Japan Works (Fukuyama)
1, Kokan-cho
Fukuyama-city
Hiroshima-pref.
721-8510
Tel. (0)84 945 3160 Fax (0)84 945 3101 EMail mailto:k-nibu@jfe-steel.co.jp Web http://www.jfe-steel.co.jp
TM + Acc = OLAC process
For differential thickness plates, the maximum thickness differential for a thickness of 50mm is 10mm for normal strength grades and 6mm for higher strength
grades
Approved for the supply of plates with specified through thickness properties (Z25/Z35).

JFE STEEL CORPORATION Yokohama Steelmaking B.O.S. / Con Cast As below
AH42, DH42, EH42 83
AH27S, AH32, AH36, AH40, DH27S, DH32, 90
DH36, DH40, EH27S, EH32, EH36, EH40
360, 410, 460FG, 490FG, 510FG 50
360FG, 410FG 100
Tapered Plates max Normal Strength D, E 40
A, B 50
EH27S, EH32, EH36, AH40, DH40, EH40
Tapered Plates max Higher strength AH32, AH36 22
East Japan Works (Keihin)
1-1, Ohgishima
Kawasaki-ku
Kawasaki
210-0868
Tel: +81 44 322 1185 Fax: +81 44 322 1510 Email: mailto:m-toyonaga@jfe-steel.co.jp
All plate grades with specified through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS 034
Certificate No. D00/1056/0009/1 Expiry date: 29/10/2015
JFE STEEL CORPORATION Yokohama Steelmaking B.O.S/V.O.D./Con Cast austenitic stainless
East Japan Works (Chiba)
1, Kawasaki-cho
Chuo-ku
Chiba 260-0835
Tel: +81 43 262 2287 Fax: +81 43 262 2980 Email to: mas-oota@jfe-steel.co.jp
Certificate No.: MD00/4065/0001/1 Expiry Date: 07/08/2015

KOBE STEEL LTD. Kobe Steelmaking B.O.S. / Con Cast As below
Higher Strength DH42, DH50, DH55, DH62, DH69, EH42, EH50, 50
EH55, EH62, EH69, FH40, FH42, FH46, FH50,
FH55, FH62, FH69
AH46, DH46, EH46 60
AH40, DH40, EH40 80
FH27S, FH32, FH36 90
AH27S, AH32, AH36, DH27S, DH32, DH36, 100
EH27S, EH32, EH36
360, 410, 460, 490, 460FG, 490FG, 510FG 90
360FG, 410FG 100
Differential Thickness A,B, D,E, HTS up to EH36 50

List 1
Kakogawa Works
1 Kanazawa-cho
Kakogawa-city
Hyogo-pref.
Tel: +81 794 36 1151 Fax: +81 794 36 2079 Email: mailto:aa14011@steel.kobelco.co.jp
All grades with specified through thickness properties.

KOBE STEEL LTD. Kobe Steelmaking B.O.S./Ingot/Con Cast As below
Rolled Blooms Carbon, Carbon-Manganese, Alloy 600
Normal Strength A 250
Kobe Works
2 Nadahama-Higashimachi
Nada-ku
Kobe
Tel +81 78 882 8056 Fax +81 78 882 8204
Email: mailto:horikawa.kenichi@steel.kobelco.co.jp
KYOEI STEEL LTD. Nagasaki Steelmaking E.A.F. / Con Cast As below
Yamaguchi Division
Oaza Onoda 6289-18
Sanyo-Onoda City
Yamaguchi Prefecture
756-0817
Tel: +81 836 83 6172 Fax: +81 836 83 0839 Email mailto:thiraki@kyoeisteel.co.jp Web http://www.kyoeisteel.co.jp
MITSUBISHI STEEL MFG. CO., LTD. Yokohama Steelmaking E.A.F. / Ingot As below
Hirota Works
405, Aza Rokucho
Hirota, Kawahigashi-machi
Aizuwakamatsu-city
Fukushima Pref. 969-3471
tel: +81 (0) 242 75 3111 Fax: +81 (0) 242 75 2619 Email mail to: Suzuki.toshihiro@mitubishisteel.co.jp or yoshida.yuji@mitubishisteel.co.jp Web:
http://www.mitsubishisteel.co.jp
Ingots nominal 2050mm diameter x nominal 1250mm length to the above maximum weight are approved for further processing forgings.
MITSUBISHI STEEL MURORAN INC. Yokohama Semi-Finished Ingots (tonnes) as below 20
Blooms/Billets As below 515
Muroran Works
12, Nakamachi
Muroran shi
Hokkaido
050-0087
Tel: +81 (0)143 41 2831 Fax: +81 (0)143 41 2869
Email mailto:yano.masashiro@mitsubishisteel.co.jp
Web: www.mitsubishisteel.co.jp
NIHON STEEL CO., LTD. Kobe Bars Normal Strength A 38
11, Rinkai-cho
Kishiwada City
Osaka
tel: +81 724 23 5151 Fax: +81 724 39 8357
Email mailto:t.naka@nihon-steel.co.jp
Web xxxxxxx
NIPPON STEEL & SUMIKIN Nagasaki Plates Austenitic Stainless 304L, 304LN, 316L, 316LN, 317L, 317LN, 321, 55
347, 304*, 316*
Clad A/304L, D/304L, D/316L 40

List 1
STAINLESS STEEL CORPORATION
Yawata Works
2108-1, Oaza Maeda Aza Hato
Yawata Higashi-ku
Kitakyushu City, Fukuoka Pref.
* Grades 304,.and 316 may be accepted for approved applications.
Tel; +81 93 672 2290 Fax: +81 93 672 2251
Email: mailto:gohnome.fuminori@ns-sc.co.jp
web: ns-sc.co.jp/en/company/plants/yawata.php
NIPPON STEEL & SUMIKIN Nagasaki Steelmaking E.A.F. / Con Cast carbon, carbon-manganese, alloy, austenitic
stainless
Plates Austenitic Stainless 304L, 316L 8
Hot Rolled Coil Austenitic Stainless 304L, 316L 8
STAINLESS STEEL CORPORATION
Production Division, Hikari Works
3434 Shimata
Hikari City
Yamaguchi 743-8550
Tel +81 833 71 5184 Fax +81 833 71 5215
Email: mailto:shimixu.tsunehiro@na-sc.nsc.co.jp
Web: http://www.ns-sc.co.jp
NIPPON STEEL & SUMITOMO METAL Yokohama Steelmaking B.O.S. / Con Cast As below
CORPORATION
Semi-Finished Slabs As below
AH46, AH50, DH46, DH50, EH46, EH50, FH46, 70

FH50, FH69*, EH69*
AH40, DH40, EH40, FH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36, 100

EH27S, EH32, EH36, FH27S, FH32, FH36
360FG, 410FG, 460FG, 490FG, 510FG 100
Ferritic Low Temperature LHAH42, LTAH46, LTAH50, LTDH42, LTDH46, 50

LTFH46, LTFH50
LTAH40, LTDH40, LTEH40, LTFH40 80

Tapered A,B,D,E, HTS up to EH40 50
Differential Thickness A,B,D,E, HTS up to EH40 50
Boiler and Pressure Vessel 360, 410 12
Hot Coiled Strip Normal Strength A, B 25

List 1
Kimitsu Works
1 Kimitsu
Kimitsu-shi
Chiba-ken
299-1141
Materials Quality Scheme approved - MQS001
Semi Finished products include Carbon and Carbon-manganese as Fine Grain Al and Fine Grain Al+Nb slabs to 1500mm wide, to 10,400mm long (maximum
weight 24T) and Carbon, Carbon-manganese and Alloy as Killed, Fine Grain Al and Fine Grain Al+Nb Blooms to 165mm diameter, to 11m long (amaximum
weight 1.85T), all for further processing.
High strength fine grained Ti+Nb steel plates produced in the TM + Acc and TM + Acc + Temper conditions up to 70mm thickness are approved with Mn and
Al contents to be outside that given in Lloyd's Register Materials Rules. Letter 'S' is used after identification number of non-standard composition materials.
Materials Quality Scheme covers Steelmaking and rolled plates only with exception of EH/FH69 grade. Strip, plate cut from coil, sections and EH/FH69 grade
approved under Materials Survey Scheme (direct survey).
* Project specific approval only. Letter ref MAT/1100/GY/10641564 refers.
Tel: +81 (0)439 50 2194 Fax: +81 (0)439 55 8727 Email: mailto:kurogi.yasuo@nsc.co.jp Web http://www.nsc.co.jp/kimitsu/

NIPPON STEEL & SUMITOMO METAL Yokohama Steelmaking B.O.S./E.A.F./Ingot/Con Cast As Below
CORPORATION
Semi-Finished Billets carbon, carbon-manganese, alloy 190
Higher Strength AH32, AH36, DH32 200
Chain Cable Stock U1, U2, U3, R3, R3S, R4 136
API-2F 152
Muroran Works
12, Naka-machi
Muroran City
Hokkaido
050-8550
Tel: +81 (0)143 47 2337 Fax: +81 (0)143 47 2783 Email: maruyama.kenichi.nsc.co.jp Web: http://www.nsc.co.jp/muroran
The approval for bars intended for chain cable stock are for material rolled from continuous casting billets only.
Bars for mooring grade chain cable stock in grades R3, R3S and R4 are restricted to Hamanaka Chain Mfg. Co. Ltd. Himeji plant only.
Bars in Grade U3 in the above supply condition may be accepted up to 200mm diameter for the further processing for the production of forged chain cable
fittings.
Approval for billets, maximum 190mm x 190mm x 8000mm maximum weight 2.3 Tonnes, as semi finished products are for further processing for forgings.
NIPPON STEEL & SUMITOMO METAL Kobe Steelmaking B.O.S./Ingot/Con Cast As below
CORPORATION
Higher Strength FH27S 40
AH40, DH40 50
DH42, DH46, EH40, EH42, FH32, FH36, FH40, 70

FH42
EH46, EH46S, FH46, FH46S 110
FH69* 120
DH50, DH55, DH62, DH69 200
AH27S, AH32, AH36, DH27S, DH32, DH36, 210

EH27S, EH32, EH36
360, 410 115
360FG, 410FG, 460FG, 490FG, 510FG 120


List 1
Nagoya Works
3, 5 Chome
Tokai-machi
Tokai-city
Aichi Pref. 476-8686
Tel +81 52 603 7236 Fax +81 52 603 7229
Email: okushima_6d7.motohiro@nscmc.com
All grades and thicknesses with specified through thickness properties (Z35)
NIPPON STEEL & SUMITOMO METAL Nagasaki Steelmaking B.O.S. / Con Cast As below
CORPORATION
Higher Strength DH42, EH42, FH42 50
EH40S* 60
AH47, DH47, EH47, AH47-W430, DH47-W430, 70

EH47-W430, EH47-W140, DH47-W140,
AH47-W140
AH40, DH40, EH40, FH27S, FH32, FH36, FH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36, 100

EH27S, EH32, EH36
360, 410, 460, 490 90
360FG, 410FG, 460FG, 490FG, 510FG 100

LTFH32, LTFH36, LTFH40
Tapered A, B, D, E, A,B,D,E, AH27S, AH32, AH36, 50
DH27S, DH32, DH36, EH27S, EH32, EH36
Differential Thickness A,B,D 35
A,B, A,B,D,E, AH27S, AH32, AH36, DH27S, 50

DH32, DH36, EH27S, EH32, EH36
Oita Works
1, Oaza Nishinotsu
Oita-City
Oita-Prefecture
Tel +81 97 553 2122 Fax +81 97 553 2379 Email: mailto:saito.bc3.shuntaroh@jp.nssmc.com Web http://www.nssmc.com/works/oita/index.html/
All plates with specified through thickness properties except H47 grades.
* Plates in LLF27 and LLF33 up to a maximum thickness of 40 mm can be accepted for approved applications.
* Plates in EH40S are for approved applications only and may have a Nickel content up to 1.5% with a carbon equivalent of 0.4%. The Approved thickness
range of EH40S is 30mm to 60mm.
* Plates in the H47 grades to be produced to the agreed chemistry ranges and agreed max CEVs.
Materials Quality Scheme Approved - Approval No. MQS010

NIPPON STEEL & SUMITOMO METAL Yokohama Steelmaking B.O.S. / Con Cast carbon, carbon-manganese, alloy
CORPORATION
A.O.D./Con Cast austenitic stainless
Higher Strength AH32S 30
FH27S 32
FH32, FH36 43
AH42, AH46, AH50, AH55, AH62, DH42, 47

DH46, DH50, DH55, DH62
AH36S, AH40S, DH36S, DH40S, EH36S, EH40S 50
AH36, AH40, DH36, DH40, EH27S, EH32, 105

EH36, EH40
AH27S, AH32, DH27S, DH32 150

List 1
Japan
CORPORATION Plates Higher Strength 150
510FG 55
360, 410, 460, 490 63
360FG, 410FG, 460FG, 490FG 100
Ferritic Low Temperature 3.5Ni, 5Ni 30

Clad EH36/304L, EH36/316L 38
Differential Thickness EH27S, EH32, EH36 32
A,B,D, AH27S, AH32, AH36, DH27S, DH32, 35

DH36
Higher Strength AH40, DH40, EH27S, EH32, EH36 18
DH27S, DH32, DH36 20
AH27S, AH32, AH36 35
Hot Coiled Strip Normal Strength A, B, D 19
Boiler & Pressure Vessel 360FG, 360, 410FG, 410 19
Kashima Works
3 Hikari
Kashima City
Ibaraki Pref.
314-0014
Tel +81 (0)299 84 2573 Fax +81 299 84 2945
Email mailto: furakawa-jun@sumitomometals.co.jp Web http://www.sumitomometals.co.jp
SMI's Fatigue Crack Arrester (FCA) grades by the DAC process with parent plate fatigue crack growth rates guaranteed by the manufacturer and tested in
accordance with ASTM E647 may be accepted for approved applications. Properties are to be as agreed with the Society. This acceptance does not imply
concessions on either design or survey requirements.
SMI's High Welding Heat Input Steel, may be accepted for approved applications, in all higher tensile strength grades up to EH40, in the TM + ACC condition
up to 105 mm thickness, when used in accordance with SMI's guidelines for welding or line heating. This acceptance does not imply concessions on either
design or survey requirements.
SMICORE, may be accepted for approved applications, in all higher tensile strength grades up to EH36, in the TM condition up to 20mm thickness and the TM
+ ACC condition up to 30 mm thickness. The steel is to have a guaranteed CRL of 0.5 or less and to be of approved composition. This acceptance does not
imply concessions on either design or survey requirements.
(Note CRL = Corrosion Ratio by Long term test)
NIPPON STEEL & SUMITOMO METAL Kobe Bars Normal Strength A 240
CORPORATION
Pipe & Tube Unit
Amagasaki Works
1, Nishino-cho
Higashi-Mukojima
Amagasaki, 660-0856
Tel: +81 (0)6 6411 7616 Fax: +81 (0)6 6411 7612 Email: mailto:furubaya-hdy@sumitomometals.co.jp
NIPPON STEEL & SUMITOMO METAL Kobe Steelmaking B.O.S. / Con Cast carbon, carbon-manganese, alloy
CORPORATION
A.O.D./Con Cast austenitic stainless
Wakayama Works
1850 Minato
Wakayama-city
640-8555
Tel: +81 (0) 73451 1133 Fax: +81 734 51 1103 EMail: mailto:morita.a88.shinji@jp.nssmc.com Sales fax +81 34416 6789 Web: www.sumitomometals.co.jp

List 1
NIPPON STEEL & SUMITOMO METAL Kobe Sections Normal Strength A, B, D, E 50

CORPORATION
Wakayama Works [Sakai Area]

1, Chikko Yawata-cho Sakai-Ku
Sakai city
Osaka
Tel: +81 722 33 1179 Fax: +81 722 33 1185
Certificate No. MD00/4141/0004/1 Expiry: 08/07/2015
NIPPON YAKIN KOGYO Co., Ltd. Yokohama Steelmaking E.A.F. / Con Cast As below
Semi-Finished Slabs As below, austenitic stainless 200
Plates Austenitic Stainless 321, 347 10
304L, 316L 53
Fe-Ni alloys Fe-36Ni* 8
Hot Rolled Coil Austenitic Stainless 304L, 316L, 321, 347 8
Fe-Ni alloys Fe-36Ni* 3
KAWASAKI PLANT
4-2, Kojima-cho
Kawasaki-ku
Kawasaki-shi
Kanagawa - ken 210-8558
Tel: +81 44 271 3045 Fax: +81 44 271 3034
Email mailto:kensuke.miura@nyk.co.jp
Web http//www.nyk.co.jp
* accepted for approved applications
NISSHIN STEEL CO., LTD. Kobe Steelmaking E.A.F. / Con Cast As below
Hot Rolled Coil Austenitic Stainless 304L, 316L, 321, 347 8
Kinuura Works
1, Hama-cho
Hekinan-shi
Aichi- ken
447-8610
Tel: +81 566 48 7218 Fax: +81 566 48 1596 Email: mailto:hayashik@nikkinko.co.jp
OJI STEEL CO., LTD. Yokohama Steelmaking E.A.F. / Con Cast As below
Gunma Works
120, Nittasorimachi-cho
Ota-city
Gunma Pref.
370-0313
Tel: +81 276 56 2119 Fax: +81 276 56 3136
Email: mailto:y-yamazaki@oji-steel.co.jp
Web: www. oji-steel.co.jp
OSAKA STEEL CO., LTD. Kobe Steelmaking E.A.F. / Con Cast A
Semi-Finished Blooms/Billets A 190
Sakai Works
1 Chikko Yawata-cho
Sakai
Osaka
Tel +81 722 33 3901 Fax +81 722 33 3976
OSAKA STEEL CO., LTD. Kobe Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms/Billets carbon, carbon-manganese, Normal Strength, 165
Higher Strength
Osaka - Okajima Works
9-3 Minami Okajima 1 Chome
Taisho-ku
Osaka 551-0021
Tel: +81 06 6552 1447 Fax: +81 06 6552 3184
Email: ko-kisimoto@osaka-seitetsu.co.jp
Web :www.osaka-seitetu.co.jp

List 1
SANYO SPECIAL STEEL CO., LTD., Kobe Steelmaking E.A.F. / Con Cast alloy, austenitic stainless
Semi-Finished Ingots (tonnes) carbon, carbon-manganese, austenitic stainless 15
Blooms carbon, carbon-manganese, alloy, austenitic 380
stainless
Machinery alloy 125
3007 Nakashima
Shikama-ku
Himeji-shi
672-8677
Tel: +81 (0)792 35 6029 Fax: +81 (0)792 35 6027
email: taota@himeji.sanyo-steel.co.jp web: www.sanyo-steel.co.jp
Heat treatment sub contracted to Toyo Metal Treating Corporation, Takasago Plant No. 2, Takasago, Hyogo Pref., Japan.

SHINKANSAI STEEL CORPORATION Kobe Steelmaking E.A.F. / Con Cast As below
Sakai Works
5, Shiohama-cho
Sakai
Osaka
Tel: +81 (0)72 228 5121 Fax: +81 (0)72 228 7119 Email: mailto:h-ue@shinkansai-steel.co.jp Web: http://www.shinkansai-steel.co.jp
SHINKANSAI STEEL CORPORATION Kobe Steelmaking E.A.F. / Con Cast As below
Hoshida Works
4-26-1, Hoshida Kita
Katano-shi
Tel: +81 (0)72 891 0624 Fax: +81 (0)72 893 1319
Email mailto:h-ito@shinkansai-steel.co.jp
Web http://www.shikansai-steel.co.jp
THE JAPAN STEEL WORKS, LTD. Yokohama Steelmaking E.A.F. / Ingot As below
360FG, 410FG, 460FG, 490FG, 510FG 50
Clad AH32/304L, AH32/316L, AH32/316LN, 19
AH32/317L
AH32/S31803 30
A/304L, B/304L, D/304L, E/304L, A/316L, 100
B/316L, D/316L, E/316L
Muroran Plant
4, Chatsu-machi
Muroran
Hokkaido
051-8505
Tel +81 (0)143 22 0539 Fax +81 (0)143 22 5736
email: kotaro_ishio@jsw.co.jp web: www.jsw.co.jp
TOKAI SPECIAL STEEL CO., LTD. Kobe Steelmaking B.O.S. / Con Cast carbon, carbon-manganese
3, 5-Chome
Tokai-Machi
Tokai-shi
Aichi-ken
Tel +81 52 603 7236 Fax +81 52 603 7229
email: komparu.58q.tomoaki@nssmc.co.jp

TOKYO STEEL MANUFACTURING CO., LTD. Nagasaki Steelmaking E.A.F. / Con Cast As below

List 1
Kyushu Plant
3-5-1, Minami-Futajima
Wakamatsu-ku
Kitakyusyu City
Fukuoka 808-0109
Tel: +81 93 701 2631 Fax: 81 93 791 2639
Email: mailto:fukui@tokyosteel.co.jp
Web http://www.tokyosteel.co.jp
TOPY INDUSTRIES, LTD. Kobe Steelmaking E.A.F. / Con Cast As below
Sections Normal Strength E 20
A, B, D 35
EH27S, EH32, EH36, FH27S, FH32, FH36
Toyohashi Works
1, Akemi-cho
Toyohashi-shi
Aichi-ken
Tel +81 532 25 1111 Fax +81 532 25 7401
Email: mailto: m-takeuchi@topy.co.jp
web: http://www.topy.co.jp
YAMATO STEEL CO., LTD. Kobe Steelmaking E.A.F. / Con Cast As below
EH27S, EH32, EH36
380, Kibi, Ohtsu-ku
Himeji City
Hyogo-pref.
Tel: +81 (0)79 273 0716 Fax: +81 (0)79 272 0914 Email mailto: knakaue@yamatosteel.co.jp Web:http://www.yamatokogyo.co.jp
Korea
BUSAN STEEL CO., LTD. Busan Port Plates from coils Austenitic Stainless Steel 304L, 304LN, 316L, 316LN, 317L, 317LN, 321, 8
347
1538-2, Songjung-Dong
Gangseo-Gu
Tel: +82 51 (0)3251131
DK CORPORATION Ulsan Plates Austenitic Stainless 304L, 304LN, 316L, 316LN 80
Duplex Stainless UNS S31803, UNS 32900*, UNS 32205* 50
#612-1, Go Hyun Ri
Chung Ha Myun
Buk-Ku, Pohang Gyeongsangbuk-do
Tel: +82 54 245 3063 Fax: +82 54 245 3065 Email:mailto:kcsohn@dkcsteel.com Web:http://www.dkcsteel.com
*accepted for approved applications
The scope of approval is for the heat treatment and final testing of plates only from rolled plates supplied from approved works.
DONGKUK STEEL MILL Co. Ltd. Ulsan Steelmaking E.A.F. / Con Cast carbon-manganese
Semi-Finished Blooms/Billets carbon-manganese 480
A, B 83
EH27S, EH32, EH36, FH27S, FH32, FH36
360AR, 410AR 40
360FG, 410FG 50
Sections Normal Strength D 25
A, B 32
Higher Strength AH27S, DH32 25
AH32, DH27S 32

List 1
Pohang Works
880 Songdong-Ri
Daesong-Myun, Nam-Gu
Pohang City, Kyungsangbuk-Do
Tel: +82 542 715687 Fax: +82 023 179055
email: donghee.lee@dongkuk.com web: www.dongkuk.com
Billets to 150 x 150mm, Blooms to 200 x 250 & 250 x 300, Beam Blanks to 400 x 480 x 120mm.
DONGKUK STEEL MILL Co. Ltd. Seoul Plates Normal Strength E 83
A, B, D 100
Higher Strength AH32, AH36, AH40, DH32, DH36, DH40, EH32, 83
EH36, EH40
Boiler & Pressure Vessel 460AR 35
360AR, 410AR 40
490FG 50
460FG, 510FG 70
360FG, 410FG 100
Dangjin Works
400, Hanjin-ri,
Songak-eup, Dangjin-kun,
Chungnam
Tel: +82 (0) 41 351 4679 Fax: +82 (0) 41 317 9083 Email: dongjin.kim@dongkuk.com Web: http://www.dongkuksteel.co.kr
Plates in the Normalised supply condition Fine Grain Al+V are only accepted in the thickness range >30mm to 70mm.
Plates with specified through thickness properties may be accepted with the suffix Z35 applied to Normal Strength Grades A to D in the Normalised Fine
Grain Al.
Certifcate Number: MD00/3773/0008/1 Expiry: 12/04/2016
DONGYANG S.TEC. CO., LTD Ulsan Plates from coils Normal Strength A 20
#619-12, Munduk-Ri,
Ocheon-Eup Nam-Gu,
Pohang-city, Kyeongbuk,
Tel: +82 54 292 6181 Fax: +82 54 291 6548
Email: kyb4621@hanmail.net
Website www.dystec.co.kr
DOOSAN HEAVY INDUSTRIES & CONSTRUCTION Changwon Steelmaking E.A.F. / Ingot As below
CO., LTD.
stainless
Changwon Plant
555, Guygok-dong
Changwon
Kyungnam
641-792
Tel +82 55 278 4591 Fax no. +82 55 278 8506
Email kisu.kwon@doosan.com
Web www.doosan.com
FINE BESTEEL CO LTD Changwon Sections Normal Strength B, D, E 18
A 30
25-1 Ha-Ri, Changnyeong-Up,
Changnyeong-Gun,
Gyeongnam,
Tel: +82 (0)55 259 2000 / 2064 Fax: +82 (0)55 259 2060
Email: hselfgod@finebesteel.com
Web www.fine-besteel.com
HYUNDAI STEEL COMPANY Seoul Steelmaking E.A.F./Ingot/Con Cast As below
Inchon Plant
63, Jungbong-Daero
Dong-Gu
Inchon
Tel: +82 32 760 2753 Fax: +82 32 760 2866 Email: arom@hyundai-steel.com Web: http://www.hyundai-steel.com
Sections flat bars up to 400 mm width.

List 1
HYUNDAI STEEL COMPANY Ulsan Steelmaking E.A.F. / Con Cast As below

Semi-Finished Blooms/Billets carbon, carbon-manganese, alloy
A 37
Higher Strength AH27S, AH40, DH27S, DH40, EH27S, EH32, 18
EH36, EH40, FH27S, FH32, FH36, FH40
AH32, AH36, DH32, DH36 37
Ferritic Low Temperature LTAH27S, LTAH32, LTDH27S, LTDH32, 18
LTEH27S, LTEH32, LTFH27S, LTFH32, LTFH36,
LTFH40
Bars Chain Cable Stock R3S, R4 110
U1, U2, U3, R3 150
Pohang Plant No. 1
444 Songnae-Dong
Nam-Gu
Pohang
Tel: +82 54 271 1479 Fax: +82 54 271 1512
Email: mailto:2007372@hyundai-steel.com
Web: http://www.hyundai-steel.com
HYUNDAI STEEL COMPANY Ulsan Steelmaking E.A.F. / Con Cast carbon-manganese
Pohang Plant No. 2
1857 Jang Heung-Dong
Tel No. +82 54 271 1479 Fax No. +82 54 271 1512
Email mailto:2007372@hyundai-steel.com
Web: www.hyundai-steel.com
HYUNDAI STEEL COMPANY Seoul Steelmaking B.O.S./E.A.F./Con Cast As Below
HR Coil Plant
1480, Bukbusaneop-ro
Songak-eup
Dangjin-si
Chungncheongnam-do
Tel: +82 41 680 1691 Fax +82 41 680 1699 Email; jwmking@hyundai-steel.com Web: http://www.hyundai-steel.com
Slabs with nominal 2200mm width x nominal 4400mm length
HYUNDAI STEEL COMPANY Seoul Plates Normal Strength A, B, D, E 100
AH47, DH47, EH47 83
AH27S, AH32, AH36, AH40, DH27S, DH32, 100
DH36, DH40, EH27S, EH32, EH36, EH40
460FG, 490FG 83
360FG, 410FG 100
Ferritic Low Temperature LTDH27S, LTDH32, LTDH36, LTFH27S, 40
LTFH32, LTFH36
Dangjin Works
1480, Bukbusaneop-ro
Songak-Eup
Dangjin-Si
Chungcheongnam-do
Tel: +82 41 680 1690 or 1685 Fax +82 41 680 1699 Email; jwmking@hyundai-steel.com Web: http://www.hyundai-steel.com
Approval for plates in grades AH27S, AH32, AH36, 360AR, 410AR, and 460AR as rolled fine grain Al+V are restricted to the thickness range 20.0mm to
35.0mm.
Approval for plates in grades AH27S, AH32, AH36, AH40, DH27S, DH32, DH36, DH40, EH27S, EH32, EH36, EH40 for the TM+Acc fine grain Al+Nb+Ti
supply condition are restricted to the thickness range >15.0mm to 83.0mm.
Approval for plates in grades LTDH27S, LTDH32, LTDH36, LTFH27S, LTFH32, LTFH36 for the TM+Acc fine grain Al+Nb+Ti supply condition are restricted to
the thickness range >15.0mm to 40.0mm.
Approval for plates in Normalising Rolled condition are restricted to maximum 3200mm width.
Plates with specified through thickness properties may be accepted with the suffix Z35 applied to;
Normal Strength Grades A & B in the As-Rolled Fine Grain Al supply condition, Grades A to D in the Normalised Fine Grain Al+Nb+V supply condition and
Grades A to E in the TM+Acc Fine Grain Al+Nb+Ti supply condition; Higher Strength Grades in the TM+acc Fine Grain Al+Nb+Ti supply condition and TM
Fine Grain Al+Nb+Ti supply condition; Ferritic Low Temperature Grades LTDH27S to LTFH36 Fine Grain Al+Nb+Ti in the Thermo Mechanical or TM+Acc
supply condition as applicable to approved thickness.
Plates in grades AH47, DH47 and EH47; FG Al+Nb+Ti; TM+Acc; are restricted to supply in the thickness range 50mm to the maximum indicated above.

List 1
JEENYANG IND. Co., Ltd. Ulsan Bars Machinery alloy 120

446, Bonchon-Dong
Yeongcheon-City,
Keongbuk,
Tel: +82 (0)54 335 3500 Fax: +82 (0)54 335 0355
Email: dhshon@jysteel.com Web: www.jysteel.com
Cert No MD00/3897/0001/1 Expiry date: 23/03/2014

KISCO Changwon Steelmaking E.A.F. / Ingot As below
N° 70, Shinchon-dong
Changwon
Kyungnam
Tel +82 55 260 0746 Fax +82 55 282 4123
mail mailto:ojyworld@kisco.co.kr
Web page http://www.kisco.co.kr
Including steelmaking
KOREA STEEL SHAPES CO., LTD Busan Port Sections Normal Strength A 15
Higher Strength AH32 30
Noksan Works
84, Noksansandan 407-Ro,
Gangseo-Gu
Busan,
Tel: +82 51 310 8912 Fax: +82 51 831 3951
email nawoo1@ekosco.com web www.ekosco.com

KOREA STEEL SHAPES CO., LTD Changwon Steelmaking E.A.F. / Con Cast As below
Semi-Finished Billets A, AH32, AH36, carbon, carbon-manganese 220
Chilseo Works
68, Gyenae-Ri, Chilseo-Myeon
Haman-Gun
Gyeongnam
Tel: +82 55 589 1159
KWANG JIN IND CO. LTD. Busan Port Bars Machinery austenitic stainless 85
alloy 93
307-103 Shinpyeong-dong,
Saha-gu,
Busan,604-030
Tel No: +82 51 220 9262 Fax No. +82 51 204 9172
Email: yukonland@kjsteel.co.kr
Web Address www.kjsteel.co.kr
Cert No MD00/3758/0002/1 Expiry date 14.03.2016
POSCO Gwangyang Works Changwon Steelmaking B.O.S. / Con Cast As below
Higher Strength EH47 80
AH27S, AH32, AH36, AH62, AH69, DH27S, 100
DH32, DH36, DH62, DH69, EH27S, EH32,
EH36, EH62, EH69
510FG
700 Kumho-dong
Kwangyang-si
Cheonnam 545-711
Tel: +82 61 790 2170 Fax: +82 61 790 2909 Email: mailto:ssyang@posco.com Web: http://www.posco.com
Approved for semi-finished products, slabs, nominal 1750mm wide x 6000mm long.
Hot rolled coils in normal strength grades in the supply condition thermomechanical fine grain aluminium are restricted to the thickness ranges >12 to 22mm.
POSCO Pohang Works Ulsan Steelmaking B.O.S./E.A.F./Con Cast As Below
FH27S, FH32, FH36 83
AH40, DH40, EH40 90
AH27S, AH32, AH36, DH27S, DH32, DH36, 100
EH27S, EH32, EH36
460FG, 490FG, 510FG 90

List 1
Korea
POSCO Pohang Works Ulsan Plates Boiler & Pressure Vessel 360FG, 410FG 100
Austenitic Stainless 304L, 304LN, 316L, 316LN 80
Duplex Stainless UNS S31803, UNS 32900*, UNS 32205* 50
Hot Rolled Coil Normal Strength E 12
A, B, D 22
Higher Strength EH27S, EH32, EH36 16
AH27S, AH32, AH36, DH27S, DH32, DH36 22
360FG, 410FG 22
5, Dongcheon-Dong
Nam-ku, Pohang City,
Kyungsangbuk-Do
Tel: +82 2 3457 3838 Fax: +82 2 3457 6000
email: ayoung89@posco.com web: www.posco.com
All plates accepted with specified through thickness properties except AH47, DH47 and EH47.
Slabs as semi-finished products nominal maximum width 2200mm x nominal maximum length 5000mm to the above maximum thickness are approved for
POSCO SPECIALITY STEEL CO., LTD. Changwon Steelmaking E.A.F. / Ingot As below
Semi-Finished Ingots (tonnes) duplex stainless 17
carbon, carbon-manganese, alloy, austenitic 150
stainless
Bars Structural carbon, carbon-manganese, alloy, duplex 150
stainless
austenitic stainless 170
147,Jeokhyeon-Ro
Seongsan-Gu
Changwon,
Gyeongnam
Tel: +82 (0)55 269 6727 Fax: +82 (0)55 269 6907 Email:mailto:soonpark@poscoss.com
http://www.poscoss.com
S & STEEL CO., LTD. Busan Port Plates from coils Normal Strength A 18
1620 Dadae-dong, Saha-gu
Busan
Tel: +82 51 262 7525 Fax: +82 51 924 7902
Email: sadrain888@hanmail.net
Web: http://www.sdstl.co.kr
SPP YULCHON ENERGY CO., LTD. Mokpo Steelmaking E.A.F. / Ingot As below
Block 8, Yulchon Industrial Complex l, Sinseong-ri
Haeryong-myeon, Suncheon City, Jeollanam-do
Zip code: 540856
Tel: +82 61 760 7100 Fax: +82 61 725 7733 Email: kimlh@spp.co.kr Web: http://www.sppycenergy.co.kr
Ingots as semi finished products are approved for further processing for forgings, nominal maximum dimensions 1630/1850mm diameter x 2850mm long, to the
above maximum weight.
SeAH BESTEEL CORPORATION Mokpo Steelmaking E.A.F./Ingot/Con Cast As below
Semi-Finished Ingots (tonnes) alloy 109
Bars alloy 350
R4S, R4S 146
R4 155
U1, U2, U3, R3, R3S 165

List 1
Gunsan Plant
1-6, Soryong-Dong
Gunsan City
Jeonlabuk-Do
Tel: +82 63 460 8222 Fax: +82 63 460 8099
Email: mailto:ssc0105@seahbesteel.co.kr
Web:http://www.egs.seah.co.kr
Approval for Chain Cable Stock Grades R3, R3S, R4, R4S and R5 is restricted to supply to DAI HAN ANCHOR CHAIN MFG CO. LTD and Grades R3, R3S
and R4 to Pu Sung Metal Co., Ltd.
Semi Finished Products - Ingots, Carbon & Carbon-manganese nominal sizes 2100 / 2350mm diameter x 2800mm long, and Alloy nominal sizes 2350 / 2600mm
diameter x 3050mm long, to the above maximum weight approved for further processing for forgings.
Semi Finished Products - Blooms to nominal 390mm width x 5400mm length, to above maximum thickness approved for further processing for Forgings and
Rolled Products.
Semi Finished Products - Billets to nominal 180 width x 11500mm length, to above maximum thickness approved for further processing for Rolled Products.
Alloy grade bars as semi-finished products nominal maximum length 12,000mm to the above maximum diameter are approved for further processing for forged
products.
YK STEEL CORP. Busan Port Steelmaking B.O.S. / Con Cast As below
90 Gupyung-Dong
Saha-Gu
604-817
Busan
Tel. +82 (0)51 260 2457 Fax +82 (0)51 265 2430 Email:mailto:jakim@yksteel.co.kr Web: http://www.yksteel.co.kr
Luxembourg
ARCELORMITTAL BELVAL ET DIFFERDANGE Lyon Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms Normal Strength, Higher Strength 100
EH27S, EH32, EH36
BELVAL MILL
TMB Rolling Plant
66 rue de Luxembourg
L4009 Esch sur Alzette
Tel: +352 58 2885 Fax: +352 5835 81 Contact: Mr Muller
Email: mailto:roberto.klecker@arcelor.com
Web:www.arcelor.com
ARCELORMITTAL BELVAL ET DIFFERDANGE Lyon Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms Higher Strength 135
Sections Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36, 40
EH27S, EH32, EH36
Differdange Mill
L 4009 Esch sur Alzette
Tel: +352 58 2028 85 Fax: +352 5835 81 Email: mailto:roberto.klecker@arcelormittal.com
Web http://www.arcelormittal.com
Beam Blanks as semi-finished products (referred to as blooms above) nominal 500nn overall width x nominal 1150mm overall length, to the above overall
maximum thickness are approved for further processing for rolled products.
ARCELORMITTAL RODANGE ET SCHIFFLANGE Lyon Sections Normal Strength A, B, D 30
Higher Strength AH36, DH36 30
Rodange Mill
2, Rue de L'industrie
L-4801 Rodange
Tel: +352 5019 2655 Fax: +352 5019 2217
Email: mailto:stephane.arnault@areclormittal.com
Web http://www.ares.lu
Certificate No. MD00/2266/0005/1 Expiry date: 18/01/2013 "SUSPENDED"

List 1
Macedonia
FAKOM A.D. Beograd Fabricated Sections Normal Strength A 35
St. Aleksandar Makedonski No.5
POB 439
1000 SKOPJE
Tel No.: +389 317 4023, Fax: +389 317 3564
email: mailto:info@fakom.com.mk
Web http://www.fakom.com.mk
MAKSTIL A.D.- SKOPJE Beograd Steelmaking E.A.F. / Con Cast As below
360, 410, 460, 490, 460FG, 490FG, 510FG 50
360FG, 410FG 100
XVI Makedonska brigada 18
P.O. Box 599
1000-Skopje
Tel: +389 2 328 7130 Fax: +389 2 3287017 Email mailto:igor.bogeski@makstil.com.mk Web http://www.makstil.com
Specified through thickness properties for plates up to 50 mm thickness
Malaysia
JI KANG DIMENSI Sdn. Bhd. Kuala Lumpur Plates Normal Strength A 30
Lot 69-71, Kawasan Perindustrian Gebeng
26100 Kuantan
Pahang Darul Makmur
Tel: +609 583 9881 Fax: +609 583 4551
Email: mailto: ji_liw@163.com
Web: www.jikangdimensi.com
Mexico
ARCELORMITTAL LAZARO CARDENAS, S.A. de Metepec/Veracr Steelmaking E.A.F. / Con Cast carbon, carbon-manganese
C.V. uz
Av Francisco J. Mujica N° 1-B

60950- Lázaro Cárdenas
Michoacan
Steel types carbon and carbon-manganese cover the supply of blooms for processing into normal strength, high strength and ferritic steels for low temperature
service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible for
ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical properties
Tel: +52 753 533 1871 Fax: +52 753 533 1187
Email:carmen.aparaicio@arcelormittalsteel.com
Web http://www.arcelormittalsteel.com
Norway
CELSA ARMERINGSSTÅL AS Oslo Steelmaking E.A.F. / Con Cast carbon, carbon-manganese
Semi-Finished Billets A, carbon, carbon-manganese 160
Mo Industripark
PO Box 500
N-8601 Mo i Rana
Tel: +47 7513 6500 Fax: +47 7513 6845 Email: mailto:halvard.meisfjord@celsanordic.com Web http://www.celsanordic.com

List 1
Poland
''HUTA POKÓJ'' S.A. Katowice Plates Normal Strength A, B, D, E 25
Boiler & Pressure Vessel 360AR, 410AR, 360, 410, 360FG, 410FG 25
ul. Niedurnego 79
41-709 Ruda Slaska
Tel +48 32 772 4110 or +48 602 593 445 Fax +48 32 772 4856 Email: dkj@hutapokoj.eu Web: http://www.hutapokoj.eu
ALCHEMIA S.A. Katowice Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy, austenitic
stainless
stainless
ZAKLAD HUTA BATORY
ul.Dyrekcyjna 6
41-506 Chorzów
Tel: +48 32 77 22 237 Fax:+48 32 77 22 060
email: :sekretariat.hbt@alchmiasa.pl
web: www.alchemiasa.pl

ARCELORMITTAL POLAND S.A. Katowice Steelmaking B.O.S. / Con Cast As below
Boiler and Pressure Vessel 410 FG, 360 FG, 460 FG 16
ODDZIAL W KRAKOWIE
ul. Ujastek 1
30-969 Kraków
Tel: +48 12 290 1817 Fax: +48 12 290 5591
email: andrzej.zajac@arcelormittal.com web: www.arcelormittal.com/poland
Slabs as semi finished products are approved for further processing for rolled products to the maximum thickness shown above and nominal 1580mm width
and 11000mm length.
Coils and plates are approved to maximum 2100mm width.

ARCELORMITTAL POLAND S.A. Katowice Steelmaking B.O.S. / Con Cast carbon, carbon-manganese, alloy
Blooms/Billets carbon, carbon-manganese, Alloy 280
A 20
Oddzial w Dabrowie Gorniczej
Al. J. Pilsudskiego 92
41-308 Dabrowa Gornicza
Tel: +48 32 776 87 14 Fax: +48 32 776 84 86 Email wojciech.michalczyk@arcelormittal.com Web: http://www.arcelormitta.com/poland/
Approved for ingots, and continuously cast products for re- rolling in all the normal and higher tensile strength grades.
ARCELORMITTAL WARSZAWA Sp. z.o.o. Katowice Steelmaking E.A.F./Ingot/Con Cast As below
ul. Kasprowicza 132
01-949 Warszawa
Tel: +48 22 835 8081 Fax: +48 22 835 8638
Email: mailto:beata.pietrzyk@arcelormittal.com
Web: http://www.arcelormittal-warszawa.com
CELSA "HUTA OSTROWIEC" Sp. z o.o. Katowice Steelmaking E.A.F. / Ingot As below
ZAKLAD WYROBOW KUTYCH
ul. Samsonowicza 2
27-400 Ostrowiec Swietokrzyski
Tel: +48 (0)41 2492390 Fax: +48 (0)41 2493779
EMail:mdunaj@celsaho.com
Web page http://www.celsaho.com
Ingots size maximum 130 MT 2.33 m diameter

List 1
CMC ZAWIERCIE S.A. Katowice Steelmaking E.A.F. / Con Cast As below

Semi-Finished Blooms/Billets carbon, carbon manganese 160
ul. Pilsudskiego 82
42-400 Zawiercie
Tel: +48 32 672 57 55 Fax: +48 32 672 57 59 Email: anna.wieczorek@cmc.com Web: www.cmcpoland.com
Includes billets/blooms up to 185 x 160mm.

FERROSTAL LABEDY Sp. z o.o. Katowice Steelmaking E.A.F. / Con Cast As below
ul. Zawadzkiego 47
44-109 Gliwice
Tel: +48 32 234 7600 Fax: +48 32 234 7650 EMail mailto:biuro@ferrostal.com.pl Web page http://www.ferrostal.com.pl
The semi finished products above are approved for use for further processing for the finished products defined above.
HSW - HUTA STALI JAKOSCIOWYCH SA Katowice Steelmaking E.A.F./Ingot/Con Cast As below
Rolled Billets Carbon, Carbon-Manganese, Alloy 130
Blooms/Billets carbon, carbon manganese, Alloy 270
Rolled Bars Carbon, Carbon manganese, Alloy 120
EH27S, EH32, EH36
ul. Kwiatkowskiego 1
37-450 Stalowa Wola
Tel: +48 15 813 53 20 Fax: +48 15 872 21 55 Email: mailto:handlowy@hsw-hsj.com.pl Web: http://www.hsw-hsj.com.pl
HUTA BANKOWA Sp. z o.o. Katowice Semi-Finished Rolled Billets Carbon, Carbon-Manganese, Alloy 300
Rolled Round Bars Carbon, Carbon-manganese, Alloy 250
ul. Sobieskiego 24
41-300 Dabrowa Górnicza
Tel +48 32 295 7430 Fax +48 32 262 3788
Email: z.hajduk@hutabankowa.pl;m.grzesiak@hutabankowa.pl
Web http://www.hutabankowa.com.pl
HW PIETRZAK HOLDING Sp. z o.o. Katowice Plates Normal Strength A, B, D, E 100
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 100
Clad A/304L 50
Oddzial Walcownia Blach Batory w Chorzowie
ul. Lesna 42
41-506 Chorzów
Tel: +48 604936263 or +48 32 7722525
email: beata.brzoza-kwiatek@p-h.pl
web: www.pietrzak-holding.pl
All plates with specified through thickness properties

INTERSPEED TRADE Sp. z.o.o. Katowice Sections Normal Strength A, B, D, E 40
EH27S, EH32, EH36, FH27S
Aleja Solidarnosci 12
27-400 Ostrowiec Swietokrzyski
Tel: +48 (0)41 266 0700; +48 695 385 015 Fax: +48 (0)41 266 0701 Email: mailto:interspeed@interspeed.com.pl Web page http://www.interspeed.com.pl
ISD HUTA CZESTOCHOWA Sp. z o.o. Katowice Steelmaking E.A.F. / Con Cast As below
A, B, D 75
EH27S, EH32, EH36
Boiler & Pressure Vessel 360AR, 410AR, 460AR, 460FG, 490FG, 510FG 50
360FG, 410FG 75

List 1
ul. Kucelinska 22
42-207 Czestochowa
Above plate grades may also be supplied with Z25/Z35 through thickness property requirements.
Tel: +48 34 323 8147 Fax: +48 34 323 0034

Email: maito:marketing@isd-hcz.com.pl
Web: http://www.isd- hcz.com.pl
WALCOWNIE BRUZDOWE "BATORY" Sp. z.o.o. Katowice Bars Structural carbon, carbon-manganese, alloy 150
ul. Zelazna 22
41-500 Chorzów
Tel: +48 32 772 2698 Fax: +48 32 772 2250 Email:sowinska.lilianna@wbb.net.pl Web:http://www.wbb.net.pl
Romania
ARCELORMITTAL GALATI S.A. Galatz Steelmaking B.O.S./Ingot/Con Cast As below
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 100
Sos Smardan Nr.1
800698 Galati
Tel: +40 236 802100 Fax: +40 236 802101 Email: mailto:mariana.subtirica@arcelormittal.com Web page http://www.arcelormittal.com
Approval includes for plates with specified through thickness properties, designation Z25, in all grades up to 60 mm thickness in the normalized condition.
COS TARGOVISTE S.A. Galatz Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms/Billets carbon, carbon manganese, Alloy 150
Targoviste
Sos. Gaiesti, 9-11
Jud Dambovita, 130087
Tel: +40 758 837 264 Fax: +40 245 213 322
email: dumitru.dumitru@cos-tgv.ro Web: www.cos-tgv.ro

DOOSAN IMGB S.A Galatz Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy 250
Berceni Road Nr. 104
Sector 4
041919 Bucharest
Tel: +40 21 301 2549 Fax: +40 21 301 2502 Email: mailto:ion.diaconu@kvaerner.ro

S.C. FORTUS S.A. Galatz Steelmaking E.A.F. / Ingot carbon, carbon-manganese 120
Bd. Poitiers Nr. 10
700671 IASI
Tel: +40 232 222023 Fax: +40 232 220370
Email: mailto: office@fortus-iasi.ro
Web: http://www.fortus-iasi.ro
S.C. LAMINORUL S.A. - BRAILA Galatz Sections Normal Strength A 50
Sos. Industria Sarmei nr. 2
810461 Braila
Tel +40 239 68 5597 Fax +40 239 66 9387 Email: mailto:iulian.vasilescu@laminorul.ro Web http://www.laminorul.ro
S.C. SILCOTUB S.A. Galatz Steelmaking E.A.F. / Con Cast As below
TENARIS GROUP
Steel Shop Calarasi
Prelungirea Bucurestiului Str. No.162
910125
Calarasi
Tel +40 242306 600 Fax No.
Web Address www.tenaris.com

List 1
SC DUCTIL STEEL SA Galatz Steelmaking E.A.F. / Con Cast carbon, carbon-manganese

Punct de lucru Otelu-Rosu
str. Mihai Eminescu, No 10,
cod 325700,loc Otelu Rosu
jud.Caras Severin
Tel No: +40 (0)255 532 239 Fax: +40 (0) 255 532 054
Email: maria.dutu@mechel.com
Web www.ductilsteel.ro
Certificate No: MD00/ 3888/ 0001/ 1 Expiry Date 10/03/2014
TMK-RESITA S.A. Galatz Steelmaking E.A.F. / Con Cast carbon, carbon-manganese, alloy
Semi-Finished Billets alloy 177
Traian Lalescu No. 36
Caras-Severin
Tel: +40 (0)255 217211 Fax: +40 (0)255 211883 Email: office.resita.tmk-artrom.ro
Web http://www.tmk-artrom.ro
Russia
"RM - steel" Ltd. St. Petersburg Sections Normal Strength A, B, D 14
DH36, DH40, EH27S, EH32, EH36
11, Sedova street
192019, St Petersburg
Tel: +7 812 318 0015 Fax: +7 812 568 0015
Email: mailto:info@rm-steel.com
Web http//www.rm-steel.com
CHELYABINSK METALLURGICAL PLANT OAO St. Petersburg Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy
454047- Chelyabinsk
2-d Paveletskaya ul, 14
Tel; +7 351 725 30 24 Fax: +7 351 722 86 29 Email mailto:sale@mechel.ru
Ingots supllied as semi finished products are for further processing for forgings.
J.S.C. SEVERSTAL St. Petersburg Plates Normal Strength A, B, D, E 40
Higher Strength EH27S, EH32 32
AH27S, AH32, AH36, AH40, DH27S, DH32, 40
DH36, DH40, EH40
360FG, 410FG, 460FG, 490FG, 510FG 40
Rolling Mill 2800
30 Mira Street
162699 Cherepovets
Vologda Region
Tel: +7 8202 531146 Fax: +7 8202 53 2424 EMail: mailto:sales@stal.ru Web http://www.severstal.ru
Plates in the As Rolled, Normalized, Quenched and Tempered conditions with specified through thickness properties.
Plates in the Normalizing rolled condition to 2200mm maximum width.
Certificate #: MD00/0298/0010/1 Expiry date : 13/06/2016
J.S.C. SEVERSTAL St. Petersburg Plates Normal Strength A 15
DH36, DH40, EH27S, EH32, EH36, EH40
Rolling Mill 2000
30 Mira Str
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 EMail: mailto:sales@stal.ru Web http://www.severstal.ru
J.S.C. SEVERSTAL St. Petersburg Plates Normal Strength D, E 50
A, B 70
DH36, DH40, EH27S, EH32, EH36, EH40
Rolling Mill 5000
1, Lenina Prospect
"IZHORSKIE ZAVODY"
196651 Kolpino
St Petersburg
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 EMail: mailto:sales@stal.ru Web http://severstal.ru
Plates with specified through thickness properties

List 1
J.S.C. SEVERSTAL St. Petersburg Steelmaking B.O.S. / Con Cast As below

B.O.S and E.A.F Workshops
30, Mira Street
162699 Cherepovets
Vologda Region
Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 EMail: mailto:sales@stal.ru Web http://severstal.ru
JOINT STOCK COMPANY«EVRAZ NIZHNY TAGIL St. Petersburg Steelmaking B.O.S. / Con Cast carbon, carbon-manganese
METALLURGICAL PLANT»
1, Metallurgov Str.,
Nizhny Tagil,
Sverdlovsk Region, 622025
Tel:+007 3435 490611 Fax:+007 3435 496169 Email:mailto:alexander.ashihin@ur.evraz.com
Web http://www.ntmk.ru
JSC AMURMETAL St. Petersburg Steelmaking E.A.F. / Con Cast carbon, carbon-manganese, alloy
30, Vagonnaya Str
681000 Komsomolsk-on-Amure
Tel No. 007 4217 52 9333 Fax No. 007 4217 52 9333
Email: market@amurmetal.ru
Web: www.amurmetal.ru
JSC KIROVSKIY ZAVOD St. Petersburg Steelmaking O H / Ingot As below
Bars Semi-finished Products carbon, carbon-manganese 120
Petrostal Steel Works
47 Stachek Prospect
198097 St. Petersburg
Tel: +7 812 783 6813 Fax: +7 812 783 6504 Email mailto:sergey.barmashev@petrostal.kzgrou.ru Web: http://www.petrostal.spb.ru
OJSC "Magnitogorsk Iron & Steel Works" St. Petersburg Steelmaking B.O.S. / Con Cast As below
Steel Making and Central Laboratory
93, Kirova Street
455000 Magnitogorsk
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: seller@mmk.ru Web http://www.mmk.ru
Approval covers for slabs as detailed above to nominal width 2520mm and nominal length 7000mm.
OJSC "Magnitogorsk Iron & Steel Works" St. Petersburg Hot Rolled Coil Normal Strength A 10
Rolling Mill 2000
OJSC "Magnitogorsk Iron & Steel Works" St. Petersburg Plates Normal Strength A 25
Rolling Mill 2350
OJSC "Magnitogorsk Iron & Steel Works" St. Petersburg Hot Rolled Coil Normal Strength A 10
Rolling Mill 2500
OJSC "Magnitogorsk Iron & Steel Works" St. Petersburg Plates Normal Strength A 50
Rolling Mill 4500
The approved minimum thickness is 30.0mm
OJSK Novolipetsk Iron & Steel Corporation Moscow Steelmaking B.O.S. / Con Cast As below
DH36, DH40, EH27S, EH36, EH40
360, 410, 360FG, 410FG 16

List 1
398040, Russia
Pl. Metallurgov 2, NLMK
Lipetsk
Tel: +7 4742 444688 Fax: +7 4742 441111
Email:mailto:info@nlmk.ru
Web:http://www.nlmk.ru
Telex: 412630NLMK RU
OSKOL St. Petersburg Steelmaking E.A.F. / Con Cast carbon, carbon-manganese
Semi-Finished Blooms carbon, carbon-manganese, Normal Strength, 360
Higher Strength
ELECTROMETALLURGICAL KOMBINAT
309515 Stary Oskol-15
Belgorod Region
Tel +07 4725 375364 Fax +07 4725 373755 vformin@oemk.ru Web http://www.oemk.ru
Blooms as semi finished products; normal strength and higher strength; nominal 300mm maximum width x nominal 12,000mm maximum length are approved
for further processing for rolled products.
Blooms as semi finished products; carbon and carbon-manganese; nominal 300mm maximum width x nominal 12,000mm maximum length are approved for
further processing for bars for chain cable stock..
URAL STEEL Open Joint-Stock Company St. Petersburg Steelmaking O H / Ingot As below
Plates Normal Strength B, D 40
A 50
1, Zavodskaya Street
Novotroitisk
Orenburg Region
462353
Tel: +7 3537 66 20 66 Fax: +7 3537 66 25 27 Email: mailto:d.bochkov@uralsteel.com Web: http://www.uralsteel.com
Serbia
ZELEZARA SMEDEREVO D.O.O. Beograd Steelmaking B.O.S. / Con Cast As below
Radinac
11300 Smederevo
Tel: +381 26 224 429 Fax: +381 26 225 069 email: mailto:martintucek@usske.sk
Slovak Republic
U.S. STEEL KOSICE, s.r.o. Prague Steelmaking B.O.S. / Con Cast A, B, D, E, AH32, AH36, DH32, DH36, EH32,
EH36
Vstupny areal U.S. Steel
044 54 Kosice
Tel: +421 55 673 4731 Fax: +421 55 675 4731 Email: mailto:fkoca@sk.uss.com Web: http:www.usske.sk
Semi-finished products in carbon and carbon-manganese steels in all normal strength grades and higher tensile strength grades up to EH36 with maximum
dimensions 1540mm wide to 12000mm long and thickness as stated.
ZELEZIARNE PODBREZOVA A.S. Prague Steelmaking B.O.S. / Con Cast As below
Kolkáreñ 35
976 81 Podbrezova
Tel: +421 48 645 4040 Fax: +421 48 645 4041
email: turis@zelpo.sk web: www.zelpo.sk

List 1
Slovenia
ACRONI, d.o.o. Zagreb Steelmaking E.A.F. / Con Cast carbon, carbon-manganese
B.O.S/V.O.D./Con Cast austenitic stainless
Semi-Finished Slabs carbon, carbon-manganese, austenitic stainless 250
EH27S, EH32, EH36
Boiler & Pressure Vessel 360AR, 410AR, 360, 410, 360FG, 410FG, 460FG, 40
490FG, 510FG
Austenitic Stainless 304L, 316L, 317L, 321, 347 70
Member of Slovenian Steel Group
Cesta Borisa Kidrica 44
SI - 4270 Jesenice
Tel: +385 4 584 1040 Fax: +385 4 584 1068 Email: mailto:askube@acroni.si Web: http://www.acroni.si
METAL RAVNE d.o.o. Zagreb Steelmaking E.A.F. / Ingot carbon, carbon-manganese, austenitic stainless
Koroška cesta 14
2390 Ravne na Koroškem
Tel: +386 2 870 7200 Fax: +386 2 870 7219 Email: mailto:stanko.triglav@metalravne.com Web: http://www.metalravne.com
South Africa
ARCELORMITTAL SOUTH AFRICA LTD. Johannesburg Steelmaking B.O.S./E.A.F./Con Cast As Below
Plates Normal Strength B, D, E 30
A 50
Higher Strength AH32, AH36, DH32, DH36, EH32, EH36, FH32, 30
FH36
360AR, 410AR 40
LTEH36, LTFH32, LTFH36
Vanderbijlpark Steel
Delfos Boulevard
Vanderbijlpark, 1911
PO Box 2, Vanderbijlpark 1900
Tel +27 (0)16 889 2657 Fax +27 (0)16 889 5019
Email: mailto:allen.pass@arcelormittal.com
Web:http://www.arcelormittal.com
EVRAZ HIGHVELD STEEL & VANADIUM, Durban Steelmaking B.O.S. / Con Cast As below
EH27S, EH32, EH36
510FG
P.O. Box 111
Witbank
1035
Mpumalanga
Tel. +27 (0)13 690 9911/ 9623 Fax. +27 (0)13 690 9559
EMail mailto:jacoline@highveld.co.za
Web http://www.highveld.co.za

List 1
Spain
ACERINOX EUROPA S.A.U. Cadiz Steelmaking E.A.F. / Con Cast As below
Plates Austenitic Stainless 304L, 316L, 321, 347 50
Coil Austenitic Stainless 304L, 316L, 321, 347 20
Palmones
11379 Los Barrios
Cadiz
Tel: +34 956 629474 Fax: +34 956 629311
email: auxiliadora.heredia@acerinox.com web: www.acerinox.com

ACEROS INOXIDABLES OLARRA S.A. Bilbao Steelmaking E.A.F. / Con Cast austenitic stainless
Larrabarri, 1
48150 Larrondo-Loiu
Vizcaya
Tel: +34 617 464 872 Fax: +34 944 531 392
email: marian.tejedo@olarra.com web: www.olarra.com
ACERÍA DE ALAVA, S.A. Bilbao Steelmaking E.A.F. / Ingot As below
Semi-Finished Blooms carbon, carbon-manganese, alloy, austenitic 470
stainless, duplex stainless, Ferritic Stainless
Steel*, Martensitic Stainless Steel*
Billets carbon, carbon-manganese, alloy, austenitic 470
stainless, duplex Stainless, Ferritic Stainless
Bars carbon, carbon-manganese, alloy, austenitic 470
stainless, duplex stainless, Ferritic Stainless
stainless, duplex stainless, ferritic stainless*,
(ACERALAVA)
Poligono Industrial De Saratxo
01470 Amurrio
Alava
Tel: +34 94 671 93 00 Fax: +34 94 672 50 62
email: carrieta@tubacex.es
* accepted for approved applications.

Approval also includes ingots in above grades up to 5 tonne.

ARCELOR MITTAL ESPAÑA Gijon Steelmaking B.O.S. / Con Cast carbon, carbon-manganese
Factoría de Avilés
Apartado 90
33402 Avilés
Asturias
Tel: +34 985 187299
Email: mailto:juan-manuel.vigil@arcelormittal.comWeb page http://www.arcelormittal.com
ARCELOR MITTAL ESPAÑA Gijon Plates Normal Strength A, B, D, E 80
Higher Strength DH40, EH40, FH27S, FH32, FH36, FH40 25
AH27S, AH32, AH36, DH27S, DH32, DH36, 80
EH27S, EH32, EH36
Factoriá de Gijón
Apartado 570
33200 Gijón
Specified through thickness properties for plates up to 50mm thickness.
Tel: +34 985 187299 Fax +34 985 187 519
Email: mailto:juan-manuel.vigil@arcelormittal.com
Web page http://www.arcelormittal.com
ARCELORMITTAL ZARAGOZA S.A. Barcelona Steelmaking E.A.F. / Con Cast As below
Semi-Finished Billets Normal Strength, Higher Strength 130

List 1
Avda. José Lopez Soriano No.100
Parque Tecnológico de Reciclado "Lopez Soriano"
Ctra. Torrecilla de Valmadrid Km 1.95
B° La Cartuja Baja 50720 Zaragoza
Tel No: +34 976 466171 Fax No +34 976 517648
Email: meruane.lakehal@mb.arcelor.com
Web www.arcelormittal.com
The approved sections are in the form of Angles, "U" and Channel to a nominal width of 140 mm.
The approved bars are in the form of Flats to a nominal width of 200 mm
COMPAÑÍA ESPAÑOLA DE LAMINACIÓN, S.L. Barcelona Steelmaking E.A.F. / Con Cast As below
Semi-Finished Billets Normal Strength 180
C/ Ferralla, 12
Poligono Industrial 'San Vicente' s/n
08755 Castellbisbal
Barcelona
Tel: +34 618 695 319 / +34 939 730 400 Fax: +34 93 817 6676 Email:mailto:s.cabrenzo@gcelsa.com Web:http://www.celsa.com
Billets as semi finished products nominal 180mm maximum width x nominal 12000mm maximum length to the above maximum thickness are approved for
Certificate Numberr: MD00/0343/0008/1 Expiry: 22/03/2016
GERDAU ACEROS ESPECIALES EUROPA S.L. Bilbao Steelmaking E.A.F. / Con Cast As below
(GERDAU)
Semi-Finished Blooms As below 300
Chain Cable Stock R3, R3S, R4, API-2F, R5 78
U2, U3 100
Planta Basauri
Bo. Ugarte, S/N
P.O. Box 76
48970 Basauri (Vizcaya)
Tel +34 944 871 726 Fax +34 944 871826
Email: mailto:alberto_cubero@gerdau.es
Web: www.gerdau.es
The approval for bars for chain cable stock grades; R3; R3S; R4; R4S; R5 are restricted to supply to Vicinay Cadenas SA to the applicable purchasing
specification; MPR3; MPR3S; MPR4; MPR4S ;MPR5.
The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval was
granted.
GERDAU ACEROS ESPECIALES EUROPA S.L. Bilbao Steelmaking E.A.F. / Ingot As below
(GERDAU)
Chain Cable Stock R3, R3S, R4, API-2F, R5 185
Planta Reinosa
Paseo Alejandro Calonje, 1
39200 Reinosa (Cantabria)
Tel: +34 942 775 187 Fax: +34 942 775 283 Email: mailto:josem.baz@gerdau.es Web http://www.sidenor.com
The approval for bars for chain cable stock grades; R3; R3S; R4; R4S; R5 are restricted to supply to Vicinay Cadenas SA to the applicable purchasing
specification; MPR3; MPR3S; MPR4; MPR4S; MPR5.
granted.
The scope of approval for bars in grade R4 includes bars to 130mm diameter produced with con cast steel manufactured at Gerdau Aceros Especials Europa SL
Planta Basauri.
The scope of approval for bars in grade R5 includes bars to 175mm diameter produced with con cast steel manufactured at Gerdau Aceros Especials Europa SL
Planta Basauri.

GERDAU ACEROS ESPECIALES EUROPA S.L. Bilbao Bars Machinery carbon, carbon-manganese, alloy 200
(GERDAU)
R3, R3S 123
R5 150
U1, U2, U3 152

List 1
Planta Azcoitia
Ctra. de Zumárraga, s/n
20720 Azcoitia
Guipúzcoa
Tel: +34 943 025206 Fax: +34 943 025299 Email: mailto:juan.aizpuru@gerdau.es Web:http//:www:gerdau.es
The approval for bars for chain cable stock grades; R3; R3S; R4 are restricted to supply to Vicinay Cadenas SA to the applicable purchasing specification; MPR3;
MPR3S; MPR4.
The approval for bars for chain cable stock grade R5 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification MPR5, this approval is with
bars to 150mm rolled from steel made at Gerdau Aceros Especiales Europa S.L. Planta Basauri and for bars to 78 mm diameter which has been manufactured
from ingots supplied by Gerdau Aceros Especiales S.L. Planta Reinosa and rolled by Gerdau Aceros Especiales S.L. Planta Azcoitia.
granted.
GERDAU ACEROS ESPECIALES EUROPA S.L. Bilbao Bars Structural carbon, carbon-manganese, alloy 37
(GERDAU)
Planta Vitoria
C/Portal De Gamarra, No. 22
01013 Vitoria (Alava)
Tel: +34 94 516 4638 Fax: +34 94 516 4748 Email: mailto:jmanuel.couso@gerdau.es Web://www.gerdau.es
HIERROS MARCELINO FRANCO S.A. Gijon Fabricated Sections Normal Strength A, B, D, E 25
Avda. Conde Guadalhorce, 131
33400 Avilés
Asturias
Tel: +34 985 56 60 67 Fax: +34 985 566 653
email: hifransa@infonegocio.com
www.grupohmf.com
Approval requires that welding is undertaken by Industrias Metalicas de Cancienes S.L ‘INMECA’.
LAMINADOS LOSAL, S.A. Bilbao Sections Normal Strength A 25
Higher Strength AH32, AH36, DH32, DH36, EH32, EH36, FH32, 11
FH36
Bekoibarra, 9
P.O. Box 17
48300 - Gernika
Tel: +34 946251400 Fax: +34 946254976 Mob: +34 68 6942188
email: agonzalez@losal.es / basterrechea@losal.es
web: www.losal.es
RUGUI S.L. Bilbao Sections Normal Strength A 25

Poligono Industrial Basarte
20720 Azcoitia (Guipuzcoa)
Apdo. de Correos no. 8 Azpeitia (Guipuzcoa)
Tel: +34 943 857311 Fax: +34 943 857312 Email: mailto:rugui@rugui.com Web http://www.rugui.com
The approved sections are in the form of flat bars up to a maximum width of 200mm.
Sweden
AB SANDVIK MATERIALS TECHNOLOGY Stockholm Steelmaking E.A.F. / Con Cast austenitic stainless, duplex stainless
E.A.F. / Ingot austenitic stainless, duplex stainless
Semi-Finished Ingots (tonnes) austenitic stainless, duplex stainless 6
Blooms austenitic stainless, duplex stainless 265
Billets austenitic stainless, duplex Stainless 150
austenitic stainless, duplex stainless 195
Bars austenitic stainless, duplex stainless 185
Bars Structural austenitic stainless, duplex stainless 185
Machinery austenitic stainless, duplex stainless 185
SE-811 81 Sandviken
Tel: +46 (0) 26 263311 Fax: +46 (0) 26 263616
email: erik.k.janssons@sandvik.com web: www.smt.sandvik.com
Semi Finished products austenitic and duplex stainless steel con-cast Blooms to 365mm wide, to 7500mm long; Con-cast Billets to 150mm wide, to 6200mm
long; As rolled billets to 195mm wide, to 6000mm long; semi-finished as rolled bars to 185mm diameter, 6900mm long for further processing for Rolled, Forged
Products

List 1
OUTOKUMPU STAINLESS AB Stockholm Steelmaking E.A.F. / Con Cast As below

Plates from coils Austenitic Stainless Steel 304L, 304LN, 316L, 321, 347 12
Duplex Stainless UNS S31803, UNS 32205* 8
Coil Austenitic Stainless 304L, 316L, 321, 347, 304LN 12
Duplex Stainless UNS S31803, UNS 32205* 8
Business Unit Special Coil Avesta Works
Box 74
SE-774 22 Avesta
Tel: +46 (0)226 81832 Fax: +46 (0)226 813 16 E-mail mailto:michael.larsson@outokumpu.com Web: http://www.outokumpu.com
*accepted for approved applications
OUTOKUMPU STAINLESS AB Stockholm Coil Austenitic Stainless 304L, 316L, 317L, 321 5
Special Coil Nyby
SE-64480 Torshälla
Tel +46 (0)1634 9000 Fax +46 (0)1634 9014 Email: mailto:claes.gefvenberg@outokumpu
OUTOKUMPU STAINLESS AB Kristinehamn Plates Austenitic Stainless 304L, 316L, 316LN, 321 50
Duplex Stainless UNS S32304** 10
UNS S31803(MOD)* 50
Business Unit Special Plate,
Quarto Plate Europe,
S-693 81 Degerfors,
Tel: 46 586 47000 Fax: 46 586 47019 Email: mailto:bengt.o.eriksson@outokumpu.com Web: http://www.outokumpu.com
* accepted for approved applications
** Grade UNS 32304 may be accepted as equivalent to 316L as shown in LR Rules when properties meet the Rule requirements.
Certificate Number MD00/1754/0006/1 Expiry date: 14/11/2014

OUTOKUMPU STAINLESS AB Kristinehamn Bars Duplex Stainless UNS S31803, UNS S32205* 200
Degerfors Stainless
SE-693 81 Degerfors
Tel: +46 (0)586 47000/47 232 Fax: +46 (0)586 47008
Email mailto:jorgen.johansson@outokumpu.com
Web http://www.outokumpu.com
EN 10088-1 grade 1.4462 accepted for approved applications only.
Certificate number MD00/3144/0004/1 Expiry date: 08/06/2014
OVAKO BAR AB. Stockholm Sections Normal Strength A, B, D, E 50
EH27S, EH32, EH36
EH27S, EH32, EH36
Boxholm Works
Box 5
59010 Boxholm
Tel: +46 0142 293600 Fax: +46 0142 293702 Email mailto: ulla.hjartkvist@ovako.com Web http://www.ovako.com
OVAKO BAR AB. Stockholm Steelmaking E.A.F. / Con Cast As below
Smedjebacken Works
S-777 80 Smedjebacken
Tel. +46 142 293733 Fax +46 (0)240 668168
EMail mailto: goran.wiktorsson@ovako.com
Web http://www.ovako.com
OVAKO HOFORS AB Stockholm Steelmaking E.A.F. / Ingot As below
Se-813 82 HOFORS
Tel: +46 (0) 298 25000 Fax: +46 0298 25025
Email: mailto:bjorn.olsson@ovako.com
Web: www.ovako.com
SCANA STEEL BJÖRNEBORG AB Kristinehamn Steelmaking E.A.F. / Ingot As below
stainless
Kristinehamnsvägen 2
S-68071 Björneborg
Tel: +46 550 25143 Fax: +46 550 27420 Email: mailto:Email: mailto:jan.örjestål@cana.no Web: http:/www.scana.no
Ingots as semi-finished products to the above maximum weight; nominal; 2070/2230mm diameter x 2600mm; are approved for further processing for forgings.

List 1
SSAB EMEA AB Stockholm Steelmaking B.O.S. / Con Cast As below

Higher Strength FH27S 40
AH27S, AH32, AH36, AH40, AH42, DH27S, 60
DH32, DH36, DH40, EH27S, EH36
DH42, EH32, EH40, EH42, FH32, FH36, FH40, 70
FH42
AH46, AH50, AH55, AH62, AH69, DH46, 80
DH50, DH55, DH62, DH69, EH46, EH50, EH55,
EH62, EH69, FH46, FH50, FH55, FH62, FH69
360FG, 410FG 75
LTFH32, LTFH36, LTFH40
OXELÖSUND
S-61380 Oxelösund
Tel +46 155 254783 Fax +46 155 254082 Email: mailto:per.hofslagare@ssab.com
Web:http://www.ssab.com
Semi-finished products in carbon and carbon-manganese steel with fine grain (element combinations as stated), slabs to 1680 mm wide, to 11000mm long of
maximum weight 30T for further processing to rolled products
SSAB EMEA AB Gothenburg Steelmaking B.O.S. / Con Cast As below
LULEÅ
97188 Luleå
Tel: +46 920 920 00 Email to: ssab.lulea@ssab.com We http://www.ssab.com
Slabs as semi finished products nominal 800-1700mm width x nominal 11000mm length to the above maximum thickness are approved for further processing
for rolled products.
Certificate No.: MD00/4194/0001/1 Expiry date: 02/07/2016
Switzerland
STAHL GERLAFINGEN AG Stuttgart Steelmaking E.A.F. / Con Cast As below
Bahnhofstrasse
CH-4563 Gerlafingen
Tel: +41 (0)32 674 2568 Fax: +41 (0)32 674 2842 Email: hjopatz@stahl-gerlafingen.com
Taiwan, Republic of China

CHINA STEEL CORPORATION Kaohsiung Steelmaking B.O.S. / Con Cast As below
AH27S, AH32, AH36, AH40, DH27S, DH32, 75
DH36, DH40, EH27S, EH32, EH36, EH40
360FG, 410FG, 460FG, 490FG, 510FG 50
No.1 Chung Kang Road
Hsiao Kang
Kaohsiung
Tel: +886 7 802 1111 ext 2208 Fax: +886 7 805 1292
Email: 54338@mail.csc.com.tw
Web page: www.csc.com.tw
All grades are approved with specified with through thickness properties.
DRAGON STEEL CORPORATION Kaohsiung Steelmaking E.A.F. / Con Cast As below
Sections Higher Strength AH32, AH36, DH32, DH36 26
100, Longchang Road,
Longjing Dist.,
Taichung City
Tel: +886 4 2630 6088 Ext. 8705 Fax: +886 4 2630 6041 Email:020288@dragonsteel.com.tw
Web www.dragonsteel.com.tw
Billets / Blooms as semi-finished products to the above maximum thickness x nominal 750mm maximum width x nominal 12000mm maximum length are
approved for further processing for rolled products.
Sections produced are H beam sections to the above maximum thickness x 900mm x 300mm overall dimensions x nominal 19000mm maximum length.

List 1
T. S. STEEL COMPANY LTD. Kaohsiung Sections Normal Strength A 15

No.6 Kon-Sixth Road
Tsuang-Hine Industrial Zone
Hsen-Kang Road
Chang-Hua Hsien
Tel: +886 4 798 0060 Fax: +886 4 799 1522
email: fang123@tssteel.com.tw

TUNG HO STEEL ENTERPRISE CORP. Taipei Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms/Billets carbon, carbon manganese, Normal Strength, 430
Higher Strength
Miao Li Works
No.22, Pingding Erhu Village,
Sihu Township,
Miaoli County 36842,
Tel: +88 637 923333 ext197 Fax: +88 637 922994 Email mailto:h32dkj@tunghosteel.com Web http://www.tunghosteel.com
TUNG HO STEEL ENTERPRISE CORP. Taipei Sections Normal Strength A 18
Kaohsiung Works
No. 8, Chia Hsing Street,
Hsiao Kang,
Kaohsiung City
Tel: +88 6 7802 3131 Fax: +88 6 801 0696 Email mailto:k23@tunghosteel.com Web http://www.tunghosteel.com
WALSIN LIHWA CORP. Kaohsiung Steelmaking E.A.F. / Con Cast austenitic stainless, duplex stainless
Semi-Finished Slabs austenitic stainless, duplex stainless 200
Billets austenitic stainless, duplex stainless 240
Yenshui Plant
3-10 Shi Jou Liau
Chin Shuei Li,
Yenshui Dist,
737 Tainan City,
Tel +886 6 6520911 ext. 407 Fax +886 6 6533076 Email mailto:nina_chen@walsin.com Web http://www.walsin.com
Semi Finished Products Austentic & Duplex Stainless slabs to 1300mm wide, to 12000mm long; square billets to 155mm wide, 12000mm long; round billets with
maximum diameter 240mm , to 12000mm long
Thailand
LPN PLATE MILL PUBLIC COMPANY LIMITED Bangkok Plates Normal Strength A 50
199/9 Moo 4 Suksawad Road
Pakklong Bangplakod
Prasamutjedee
Samutprakarn 10290
Tel: +66 2815 6400-9 Fax: +66 2815 6415
Email: mailto:labtest@lpngroup.co.th
Web: www.lpnpm.co.th
SAHAVIRIYA PLATE MILL PUBLIC COMPANY Bangkok Plates Normal Strength A, B 40
LIMITED
Chachoengsao
160 Moo 14 Sukhumvit Road
Bangpakong
Chachoengsao 24130
Tel: +66 3883 2056 ext 162 Fax: +66 3853 2370 Email mailto: natthawut.l@spm-plate.com
SAHAVIRIYA STEEL INDUSTRIES PUBLIC Bangkok Hot Rolled Coil Normal Strength B, D 8
COMPANY LIMITED
A 19

List 1
Prachuab Kirikhan
9M.7 Tumbol Mearumphueng
Amphur Bang Saphan
Prachuab Kirikhan 77140
Tel: (+66) 32 691403-5 ext 5118 Fax: (+66) 32 691408
Email mailto: savarinr@ssi-steel.com
Web http://www.ssi-steel.com
The Netherlands
NEDSTAAL B.V. Rotterdam Steelmaking E.A.F. / Ingot As below
Marine
Rapenburg 1
P.O. Box 210
2950 AE Alblasserdam
Tel: +33 (0) 78 692 3785 Fax: +31 (0) 78 692 3770 Email mailto:hans.vanzuilen@nedstaal.nl Web: http://www.nedstaal.nl
The above semi finished products to the indicated maximum weigh / thickness are approved for further reprocessing for forgings; ingots nominal maximum
dimensions 940mm x 780mm x 2300mm long; slabs nominal 620mm wide x nominal 3300mm long; billets nominal 185mm wide x 9200mm long; blooms
nominal 220mm wide x 13100mm long.
TATA STEEL IJMUIDEN B.V Amsterdam Steelmaking B.O.S. / Con Cast As below
IJmuiden Works
Postbus 10000
1970 CA IJmuiden
Tel +31 2514 92110 Fax +31 2514 70414 Email: mailtojelle.van-der-wal@tatasteel.com
web: www.tatasteel.nl
Tunisia
PALESCANDOLO CNT sarl Naples Fabricated Sections Normal Strength A 25
Parc D' Activite' Economique De Bizerte
7000 Bizerte
Tel: + 21 77 241 7292 Fax: +21 77 241 7552 Email: apalescnt@yahoo.fr
Turkey
ASIL CELIK SANAYI VE TICARET A.S. Istanbul Steelmaking E.A.F./Ingot/Con Cast As below
Gemic Koyu Mevki 16800
Orhangazi, Bursa
Tel: +90 224 280 61 00 Fax: +90 224 280 62 00 Email mailto:quality@asilcelik.com.tr
Web http://www.asilcelik.com.tr
EREGLI DEMIR VE CELIK FABRIKALARI T.A.S. Istanbul Steelmaking B.O.S. / Con Cast As below
EH27S, EH32, EH36, FH27S, FH32, FH36
Higher Strength AH32, AH36, DH32, DH36, EH27S, EH32, 15
EH36, FH27S, FH32, FH36
KDZ. Eregli
67330
Zonguldak
Tel: +90 (0)372 329 3838 Fax: +90 (0)372 323 2598 Email: mailto:kaygoren@erdemir.com.tr Web http://www.erdemir.com.tr

List 1
ÖZKAN DEMIR ÇELIK SANAYI A.S. Istanbul Steelmaking E.A.F. / Con Cast As below
Sections Normal Strength D, E 12
A, B 25
AH27S, AH32, AH36, DH27S, DH32, DH36, 28
EH27S, EH32, EH36
Bozköy Köyü
13. Cadde N:4 35800
Aliaga-Izmir
Tel +90 232 625 1515 Fax +90 232 625 1054
Email: info@ozkansteel.com
Web: http://www.ozkansteel.com
Ukraine
CJSC DONETSKSTEEL IRON AND STEEL WORKS Mykolaiv Steelmaking OH/Ingot/ Con Cast As Below
Slabs carbon, carbon-manganese 150
141 Tkachenko St
Donetsk region
83062 Donetsk
Tel: +38 (0622) 61-27-44 or 61-31-62 Fax: +38 (062) 388 04 21 Email: mailto:oksp@donmz.donetsk.ua
PJSC "ALCHEVSK IRON & STEEL WORKS" Mykolaiv Steelmaking OH/Ingot/ Con Cast As Below
B 50
A 72
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 50
360, 410 72
Shmidt st. 4, Alchevsk
Lugansk Region
94202
Tel: +38 06442 7 33 20 Fax: +38 06442 97 33 76
EMail: mailto:abrosimov@amk.lg.ua
Web page http://www.amk.lg.ua
PJSC "AZOVSTAL IRON & STEEL WORKS" Mykolaiv Steelmaking B.O.S. / Con Cast As below
A, B 100
DH36, DH40, EH27S, EH32, EH36, EH40
1, Leporsky St.
Mariupol 87500
Tel: +380 629 467 108 Fax: +380 629 468 441 Telex: 115123 VOLNA UX
Email mailto:sal@@azovstal.com.ua
Web http://www.azovstal.metinvestholding.com
Including plates with specified through thickness properties. Z35 may be applied to all grades and thicknesses
PJSC "DONETSK IRON AND STEEL WORKS" Mykolaiv Plates Normal Strength D 16
A, B 20
Higher Strength DH27S, DH32 16
AH27S, AH32 20
122 Tkachenko St
Donetsk 83062
Tel: +38 0622 61 26 35 Fax: +38 0623 3880 421 Email:mailto:oksp@donmz.donetsk.ua
PJSC "ENERGOMASHSPETSSTAL" Mykolaiv Steelmaking E.A.F. / Ingot As below
84306 Kramatorsk
Donetsk Region
Tel: +38 (06264) 6-94-93 Fax: +38 (06264) 6-94-93
Email: nosenkonina@emss.dn.ua

List 1
PJSC "ILYICH IRON AND STEEL WORKS OF Mykolaiv Steelmaking B.O.S. / Con Cast As below
MARIUPOL"
Higher Strength DH40, EH40 25
AH27S, AH32, AH36, DH27S, DH32, DH36, 50

EH27S, EH32, EH36
360FG, 410FG 50
1 Levchenko Street
Mariupol 87504
All grades and thicknesses with specified through thickness properties. Notation Z25 or Z35 may be added.
Tel: +38 (0)0 629 56 43 98
email: sergey.paramonov@ilyichsteel.com web: www.ilyichsteel.metinvestholding.com
PJSC ELEKTROMETALLURGICAL WORKS Mykolaiv Steelmaking E.A.F. / Ingot As below
DNIPROSPETSSTAL
named after A.N. Kuzmin

81 Yuzhnoye Shosse
Zaporozhye, 69008
Tel: +38 612 223 627 Fax No: +38 612 131 780
Email : OUKN@dss.com.ua
Web http://www.dss.com.ua
Including forged bars and tube blanks ( billets) in all qualities.
United Kingdom
ACENTA HOT ROLLED Energy Sections Normal Strength A 50
Coventry, UK
EH27S, EH32, EH36

EH27S, EH32, EH36
Peartree Lane
Woodside, Dudley
West Midlands DY2 0QS
Tel: +44 (0) 1384 471 200 Email: mailto:ppowell@acentasteel.com Web: http://www.acentasteel.com
CAPARO MERCHANT BAR PLC. Liverpool Sections Normal Strength A, B, D, E 12
Caparo House
P.O. Box 15
Scunthorpe
DN16 1XL
Tel +44 (0)1724 403022 Fax +44 (0)1724 403044
Email: mailto:mike.hill@cmbplc.co.uk
Web: www.cmbplc.co.uk
The approved sections include flat bar and angled bar

CELLBEAM LTD. Liverpool Fabricated Sections Higher Strength AH32, AH36, DH32 18
DH36 30
High Strength EH46-TM 20
Thorp Arch Trading Estate
Wetherby
West Yorkshire LS23 7DB
Tel: +44 (0)1737 840600
Email: neil.powell@cellbeam.co.uk
Web: www.cellbeam.co.uk

List 1
CELSA MANUFACTURING (UK) LTD. Southampton Steelmaking E.A.F. / Con Cast As below
Semi-Finished Blooms/Billets Normal Strength 140
Sections Mill
Tremorfa Works
Seawall Road,
Tremorfa,
Cardiff. CF24 5TH
Tel: +44 (0) 1568 615201 Fax: +44 (0) 1568 612626
Concast blooms/billets covers billets to 140mm x140mm and concast 'mini slabs' to 280 x 120mm.
OUTOKUMPU STAINLESS LTD. Liverpool Steelmaking E.A.F/A.O.D/L.A.F/ConCast stainless steel
Semi-Finished Ingots (tonnes) stainless steel 19
Slabs stainless steel 300
Blooms stainless steel 300
Billets stainless steel 200
LONG PRODUCTS, SMACC
P.O. Box 161
Europa Link
Sheffield, S9 1TZ
The approval for steelmaking and ingots, slabs, blooms and billets in stainless steel covers the supply of austenitic, duplex, ferritic, martensitic and precipitation
hardening grades, in accordance with the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3 or appropriate international or
national standards. The final processing mill is responsible for ordering steel which complies with their surface and internal quality standards and approved
chemical composition to enables them to achieve the required physical and mechanical properties.
Mass of slab and bloom up to 30.0T.and billet up to 20T
Tel: +44 (0)114 2616292 Fax: +44 0114 2616163

Email: mailto:richard.firman@outokumpu.com
Web: http://www.outokumpu.com
SAHAVIRIYA STEEL INDUSTRIES UK Liverpool Steelmaking B.O.S. / Con Cast As below
Steel House
Redcar
TS10 5QW
Tel: +44 01642 408053
Email: david.reevell@ssi-steel.co.uk
Web: http://www.ssi-steel.co.uk
SHEFFIELD FORGEMASTERS INTERNATIONAL Energy Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy, austenitic
LTD. Coventry, UK stainless
P.O. Box 286
Brightside Lane
Sheffield S9 2RW
Tel: +44 (0)114 2449071 Fax: +44 (0)114 2422103
Email:mailto:sales@sfm.com
Web:http://www.sheffieldforgemasters.com
TATA STEEL (UK) LTD Glasgow Plates Normal Strength E 50
A, B, D 100
Higher Strength FH40 25
FH32, FH36 30
AH42, AH46 36
AH40, DH40, DH42, DH46, EH40, EH42, EH46 65
AH32, AH36, DH32, DH36, EH32, EH36 75
360FG, 410FG 100
Ferritic Low Temperature LTFH40 25
LTAH32, LTAH36, LTAH40, LTDH32, LTDH36, 30
LTFH36
Dalzell
Motherwell ML1 1PU
Tel: +44 (0)1698 266100 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.corusgroup.com
TATA STEEL (UK) LTD Liverpool Steelmaking B.O.S./Ingot/Con Cast As below
B, D 60
A 80
Higher Strength FH40, FH42, FH46 25
AH40, AH42, AH46, DH40, DH42, DH46, EH40, 30

List 1
United Kingdom
Plates Higher Strength EH42, EH46 30
FH32, FH36 50
AH27S, AH32, AH36, DH27S, DH32, DH36, 70
EH27S, EH32, EH36
360FG, 410FG, 460FG, 490FG, 510FG 70
360, 410 80
LTEH27S, LTEH32, LTEH36, LTEH40
EH27S, EH32, EH36
Scunthorpe
P.O. Box 1
Scunthorpe DN16 1BP
Tel: +44 1724 404040 Email:maito: shipbuilding@tatasteel.com Web:http://www.tatasteel.com
All plates with through thickness properties.
TATA STEEL (UK) LTD Energy Sections Normal Strength A, B, D, E 77
Coventry, UK
Teesside
Redcar
Teesside
TS10 5RD
Tel: +44 (0)1642 406583 Fax: +44 (0)1642 406904 Email: mailto:Robin.Davies@corusgroup.com

TATA STEEL (UK) LTD Energy Sections Normal Strength A, B, D, E 20
Coventry, UK
AH32, AH36, DH32, DH36, EH32, EH36 20
Skinningrove
P.O. Box 1
Saltburn by the Sea
TS13 4ET
Tel: +44 (0)1287 640212 Fax: +44 (0)1287 643467 Email: mailto:Bary.Atkinson@corusgroup.com

TATA STEEL UK LIMITED Energy Fabricated Sections Structural Sections carbon, carbon-manganese 16
Coventry, UK
Hartlepool Works
P.O. Box 101, Weldon Road
Corby
Northamptonshire
NN17 5UA
Tel: +44 (0)1536 404704 Fax: +44 (0)1536 404212 Email: mailto:stewart.jeffrey@tatasteel.com Web: http://www.tatasteel.com
Includes fabricated hollow sections
TATA STEEL UK LIMITED Energy Sections Normal Strength A 20
Coventry, UK
EH27S, EH32, EH36
Fabricated Sections Structural Sections carbon, carbon-manganese 20
Hartlepool Works
20 Inch H.F.I. Pipe Mill
Brenda Road
Hartlepool
Teeside TS25 2EG
Tel: +44 (0)1429 527249 Mob: +44 (0)7743 842969 Email: mailto:david.evans@tatsteel.com Web:http://www.tatasteeleurope.com

List 1
TATA STEEL UK LIMITED Energy Steelmaking E.A.F./Ingot/Con Cast carbon, carbon-manganese, alloy
Coventry, UK
Semi-Finished Ingots (tonnes) as below 13
Chain Cable Stock U1, U2, U3, R3, R3S, R4 165
Rotherham & Stocksbridge Sites

Stocksbridge
Sheffield
South Yorkshire S36 2JA
Tel: +44 (0)114 2832043 Fax:
Email mailto:enquiries.ces@tatasteel.com
Web page http://www.tatasteeleurope.com
TATA STEEL UK LIMITED Energy Steelmaking B.O.S. / Con Cast As below
Coventry, UK
Port Talbot Works

Port Talbot
SA13 2NG
Tel: +44 (0)1698 266100 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.corusgroup.com
Approval covers concast slabs to nominal size 1850mm wide x 10,000mm long to the maximum thickness for further processing to rolled products.
Certificate No.: MD00/3909/0001/1 Expiry Date: 05.05.2014

TATA STEEL UK LIMITED Energy Fabricated Sections Structural Sections carbon, carbon-manganese 16
Coventry, UK
Corby Works
P.O.Box 101, Weldon Road
Corby
Northamptonshire
NN17 5UA
Tel: +44 (0)1536 404704 Fax: +44 (0)1536 404212 Email: mailto:stewart.jeffrey@tatasteel.com Web: http://www.tatasteel.com
Includes fabricated hollow sections
United States of America

ARCELORMITTAL BURNS HARBOR Chicago Steelmaking B.O.S. / Con Cast As below
A, B 50
EH27S, EH32, EH36
250 West Highway 12
Burns Harbor
IN 46304-9745
Tel: +1 219 787 4515 Fax: +1 219 787 3435 Email mailto:john.poolarz@arcelormittal.com Web: http://www.arcelormittal.com Certificate Number:
MD00/2331/0006/1 Expiry: 18/12/2015
ELLWOOD QUALITY STEEL COMPANY Chicago Steelmaking E.A.F. / Ingot carbon, carbon-manganese, alloy
700 Moravia Street
New Castle
Pennsylvania 16101
Tel: +1 724 658 6849 Fax: +1 724 658 6802
Email mailto:slubinski@elwd.com
Web: www.egi.org
EVRAZ CLAYMONT STEEL, Philadelphia Steelmaking E.A.F. / Con Cast As below 248
4001 Philadelphia Pike,
Claymont,
Delaware,
19703
Tel No. +01 302 792 5400 Fax No. +01 302 792 0203
Email: scott. diestelkamp@EvrazIncNA.com
Web: www.EvrazIncNA.com

List 1
EVRAZ OREGON STEEL MILLS Los Angeles Plates Normal Strength A, B, D 50

360FG, 410FG 50
14400 N. Rivergate Blvd.
Portland
OR 97203
Tel: +1 503 978 6130 Fax: +1 503 978 4975
Email: mailto:Christine.wrinkle@evrazincna.com Web http://www.evrazincna.com
Including all plate grades and thicknesses with specified through thickness properties (Z35)
MATERIALS QUALITY SCHEME APPROVED - MQS 047

JSW STEEL (USA) INC. Houston Plates Normal Strength E 51
A, B, D 102
DH40
5200 East McKinney Road
Baytown
Texas 77523
Tel: +1 281 383 5100 Fax: +1 281 383 1803 Email mailto: bankim.shukla@jswsteel.us Web: http://www.jswsteel.com
NUCOR STEEL MEMPHIS, INC Chicago Steelmaking E.A.F. / Con Cast As below
Semi-Finished Rolled Round Bars Carbon, Carbon-manganese, Alloy 203
Rolled Square Bars Carbon, Carbon-manganese, Alloy 254
3601 Paul R. Lowry Road
Memphis
TN 38109
Tel: +1 901 786 5416 Fax: +1 901 788 5300 Email to: Gail.Farrow@nucor.com Web http://www.nucor.com

NUCOR STEEL TUSCALOOSA INC. New Orleans Steelmaking E.A.F. / Con Cast As below
Plates from coils Normal Strength A 20
1700 Holt Road N.E.
Tuscaloosa
AL 35404-1000
Tel: +1 205 562 1200 Fax: +1 205 556 1482 Email to: jon.miller@nucor.com Web http://www.nucor.com
Materials Quality Scheme approved - MQS048

REPUBLIC STEEL Chicago Steelmaking E.A.F./Ingot/Con Cast As below
HOT ROLLED BAR DIVISION
CANTON WORKS
2633 Eighth Street N.E.
Canton
Ohio 44704-2311
Tel: +1 330 438 5543 Fax: +1 330 438 5552 Email to: DWalvoord@RepublicSteel.com Web: http://www.republicsteel.com
Ingots as semi finished products, nominal 740mm diameter x 4800mm, are approved for further processing for forgings to the maximum un-cropped weight
shown above.
SSAB ALABAMA, INC. New Orleans Steelmaking E.A.F. / Con Cast As below
A, B 50
Higher Strength AH27S, AH32, AH36, DH32, DH36 38
12400 Highway 43 North
Axis
Alabama 36050
Tel: + 01 256-546-2669 Fax: +01 256-546-2670 email mailto:lbridges@ipsco.com Web http://www.ipsco.com


List 1
STEEL DYNAMICS INC Chicago Steelmaking E.A.F. / Con Cast carbon, carbon-manganese, alloy
Semi-Finished Rolled Bars Carbon, Carbon manganese, Alloy 178
ENGINEERED BAR PRODUCTS DIVISION
8000 North County Road 225 East,
Pittsboro,
IN, 46167
Tel: +1 877 683 2277 Fax: +1 317 892 7005
Certificate No: MD00/4134/0001/1 Expiry Date: 24/03/2016
Concast blooms approved to 262 x 358 mm section.

THE TIMKEN COMPANY STEEL BUSINESS Chicago Steelmaking E.A.F. / Ingot As below
Semi-Finished Bars carbon, carbon-manganese, alloy 330
(Faircrest Steel Plant)
1835 Dueber Avenue S.W.
Canton
OH 44706-0932
Tel: +1 330 471 3263 Fax: +1 330 471 4077 Email: mailto:robert.w.hoff@timken.com Werb: http://www.timken.com

THE TIMKEN COMPANY STEEL BUSINESS Chicago Steelmaking E.A.F. / Con Cast As below
Semi-Finished Bars carbon, carbon-manganese, alloy 330
(Harrison Steel Plant)
1835 Dueber Avenue S.W.
Canton
OH 44706-0932
Tel: +1 330 471 3263 Fax: +1 330 471 4077 Email: mailto:robert.w.hoff@timken.com Werb: http://www.timken.com

Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective
officers, employees or agents are, individually and collectively, referred to in this
clause as ‘Lloyd's Register’. Lloyd's Register assumes no responsibility and shall
not be liable to any person for any loss, damage or expense caused by reliance on
the information or advice in this document or howsoever provided, unless that
person has signed a contract with the relevant Lloyd's Register entity for the
provision of this information or advice and in that case any responsibility or liability
is exclusively on the terms and conditions set out in that contract.

Lloyds Approved Mills

Uploaded by

Copyright:

Available Formats

Lloyds Approved Mills

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lloyds Approved Mills

Uploaded by

Copyright:

Available Formats

List 1

Approved Steelmakers and Manufacturers of

B.O.S. Basic Oxygen Steelmaking

Certificate # MD00/1929/0008/1 Expiry date: 20/07/2015

Page 2 As at 13 May 2014

STAHL JUDENBURG GmbH Vienna Bars Normal Strength A 120

Certifcate No. MD00/1614/0008/1 Expiry date: 30/07/2014

Approval includes the supply of z25 and z35 grades.

Approval includes pressed heads.

Billets carbon, carbon-manganese, Normal Strength 300

"Byelorussian Metallurgical Company" holding"

Page 3 As at 13 May 2014

Page 4 As at 13 May 2014

Hot Rolled Coil Normal Strength D 16

Higher Strength AH27S, AH32 16

Boiler & Pressure Vessel 460FG, 490FG 16

Av. Brigadeiro Eduardo Gomes

Page 5 As at 13 May 2014

Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36, 80

360FG, 410FG, 460FG, 490FG, 510FG 80

Rodovia Cônego Domênico Rangoni, Km 6

Certificate #: MD00/0092/0008/1 Expiry date: 05/05/2017

Page 6 As at 13 May 2014

China, People's Republic of

Page 7 As at 13 May 2014

Certificate #: MD00/1343/0015/1 Expiry date: 30/03/2016

Materials Quality Scheme Approved - MQS 038

Certificate No. MD00/3489/0007/1 Expiry date: 15/12/2014

Materials Quality Scheme Approved - MQS 051

Page 8 As at 13 May 2014

Blooms Normal Strength, Higher Strength 260

Sections Normal Strength A, B 20

Higher Strength AH27S, AH32, AH36 20

118 Hualian Road,

Certificate Number: MD00/2493/0008/1 Expiry: 13/08/2014

Page 9 As at 13 May 2014

Plates Normal Strength A, B 36

Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36 30

Boiler & Pressure Vessel 360FG, 410FG, 460FG, 490FG, 510FG 30

Middle Gongyezhong Road

Hot Rolled Coil Normal Strength A, B, D 18

Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36 18

Plates from coils Normal Strength A, B, D 18

Higher Strength AH27S, DH27S, AH32, DH32, AH36, DH36 18

Page 10 As at 13 May 2014

Certificate No: MD00/3099/0005/1 Expiry date: 07/08/2016

Page 11 As at 13 May 2014

Page 12 As at 13 May 2014

Blooms carbon, carbon-manganese, alloy 390

Bars Semi-finished Products carbon, carbon-manganese, alloy 900

Structural carbon, carbon-manganese, alloy 180

Machinery carbon, carbon-manganese, alloy 180

Chain Cable Stock R3, R3S, R4 160

U1, U2, U3 180

297, Bin Jiang East Road

Certificate Number: MD00/2306/0015/1 Expiry: 25/09/2016

Plates Normal Strength A, B, D, E 50

Higher Strength AH27S, AH32, AH36, DH27S, DH32, DH36, 50

360FG, 410FG, 460FG, 490FG, 510FG 50

3500 Plate Mill