JAPANESE INDUSTRIAL STANDARD

JIS B 8265:2010
Construction of pressure vessel—General principles
December, 2013

ERRATA (1/11)

Page Position Error Correct

32 Figure tw is the pipe thickness of schedule 160. tw is the pipe thickness of schedule 160.
11 e) Nominal diameter of the pipe fitting is
(below 80A (DN80) or under.
the
figure)
36 6.2,
Table 2 Type of Efficiency of welded joints (η ) Type of Efficiency of welded joints (η )
joints Percentage of applying the joints Percentage of applying the
radiographic examination radiographic examination

a) 100 ％ b) 20 ％ c) Not a) 100 ％ b) 20 ％ c) Not

applied applied

B－1 1.00 0.95 0.70 B－1 1.00 0.95 0.70

B－2 0.90 0.85 0.65 B－2 0.90 0.85 0.65

B－3 － － 0.60 B－3 － － 0.60

L－1 － － 0.55 L－1 － － 0.55

L－2 － － 0.50 L－2 － － 0.50

L－3 － － 0.45 L－3 － － 0.45

NOTE: The efficiency of welded
joints in the case of
cylindrical shells apply to
longitudinal and
circumference joints.
However, the calculated
thickness of cylindrical shells
applies to the longitudinal
joints.

(continued)

－6－
 B 8265:2010 ERRATA (2/11)

Page Position Error Correct

40 6.5 c) See below. See below.

6.5 c) Error: For the hub part of tube plates with hubs or flat end plates with hubs (only in the case
of machining from plates), the ultrasonic examination of the whole volume of the hub
part from the two directions, the radial and axial, of the hub shall be performed in
accordance with JIS G 0801, and the judging criteria given in 1) and 2) below shall be
satisfied.

Correct: For the hub part of tube plates with hubs or flat end plates with hubs (only in the case
of machining from plates), the ultrasonic examination of the whole volume of the hub
part from the two directions, the radial and axial, of the hub shall be performed in
accordance with JIS G 0801 before and after machining, and the judging criteria given
in 1) and 2) below shall be satisfied.

Page Position Error Correct

60 Table B.1 (continued) 9B 11A
Type: JIS G 3127
Designation: SL5N590
Base metal class
63 Table B.1 (continued) E W
Type: JIS G 3452 B B
Designation: SGP
Fabrication method
Table B.1 (continued) S S
Type: JIS G 3454 E W
Designation: STPG370
Fabrication method
Table B.1 (continued) S S
Type: JIS G 3454 E W
Designation: STPG410
Fabrication method
Table B.1 (continued) S S
Type: JIS G 3456 E W
Designation: STPT370
Fabrication method
Table B.1 (continued) S S
Type: JIS G 3456 E W
Designation: STPT410
Fabrication method
Table B.1 (continued) A W
Type: JIS G 3457
Designation: STPY400
Fabrication method

(continued)

－7－
 B 8265:2010 ERRATA (3/11)

Page Position Error Correct

65 Table B.1 (continued) S S
Type: JIS G 3460 E W
Designation: STPL380
Fabrication method
Table B.1 (continued) S, E S, W
Type: JIS G 3461 E W
Designation: STB340
Fabrication method
Table B.1 (continued) S, E S, W
Type: JIS G 3461 E W
Designation: STB410
Fabrication method
Table B.1 (continued) S, E S, W
Type: JIS G 3461 E W
Designation: STB510
Fabrication method
66 Table B.1 (continued) S, E S, W
Type: JIS G 3462 E W
Designation: STBA12
Fabrication method
Table B.1 (continued) S, E S, W
Type: JIS G 3462 E W
Designation: STBA13
Fabrication method
Table B.1 (continued) S, E S, W
Type: JIS G 3462 E W
Designation: STBA20
Fabrication method
Table B.1 (continued) S, E S, W
Type: JIS G 3462 E W
Designation: STBA22
Fabrication method
67 Table B.1 (continued) – S
Type: JIS G 3463 W
Designation: SUS329J4LTB
Fabrication method
Type: JIS G 3463 – 132, 132, 131, 129, 128, 125,
Designation: SUS329J4LTB 123, 122, 120, 119, 119
Add the values in the right as
the allowable tensile stress
values for fabrication method
W (added above), for
temperatures 40 °C, 75 °C,
100 °C, 125 °C, 150 °C,
175 °C, 200 °C, 225 °C,
250 °C, 275 °C and 300 °C,
respectively.

(continued)

－8－
 B 8265:2010 ERRATA (4/11)

Page Position Error Correct

68 Table B.1 (continued) S, E S,W
Type: JIS G 3464 E W
Designation: STBL380
Fabrication method
77 Table B.1 (continued) S : seamless pipes; E : S: seamless pipes ; B:
NOTE 3 electric resistance welded forge-welded tubes ; W :
tubes; A : submerged arc electric resistance welded
welding tubes; W : tubes; submerged arc
automatic arc welding tubes welding tubes; automatic arc
or electric resistance welded welding tubes or laser
tubes. welding tubes.
80 Table B.1 (continued) The external pressure chart The external pressure chart
Note ah) number in this row may be number in this row may be
applied to JIS G 4051, JIS G applied only when used for
4303, and JIS G 4311, only stiffening rings
when used for stiffening
rings
83 Table B.3 (continued) 205 [Outer diameter 4 mm 205 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1020 100 mm 100 mm
Quality class: O /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 30 mm]
Table B.3 (continued) 205 [Outer diameter 4 mm 205 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1201 250 mm 250 mm
Quality class: O /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 30 mm]
Table B.3 (continued) 205 [Outer diameter 4 mm 205 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1220 250 mm 250 mm
Quality class: O /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 30 mm]
Table B.3 (continued) 205 [Outer diameter 4 mm 205 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1020 100 mm 100 mm
Quality class: OL /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 30 mm]

(continued)

－9－
 B 8265:2010 ERRATA (5/11)

Page Position Error Correct

83 Table B.3 (continued) 205 [Outer diameter 4 mm 205 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1201 250 mm 250 mm
Quality class: OL /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 30 mm]
Table B.3 (continued) 205 [Outer diameter 4 mm 205 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1220 250 mm 250 mm
Quality class: OL /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 30 mm]

Table B.3 (continued) 245 [Outer diameter 4 mm 245 [Outer diameter 4 mm

Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1020 100 mm 100 mm
Quality class: 1/2H /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 25 mm]
Table B.3 (continued) 245 [Outer diameter 5 mm 205 [Outer diameter 5 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1100 250 mm 250 mm
Quality class: 1/2H /Wall thickness 0.5 mm /Wall thickness 0.5 mm
Specified minimum tensile or over up to and incl. or over up to and incl.
strength 30 mm] 25 mm]
Table B.3 (continued) 245 [Outer diameter 4 mm 245 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1201 250 mm 250 mm
Quality class: 1/2H /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 25 mm]
Table B.3 (continued) 245 [Outer diameter 4 mm 245 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1220 250 mm 250 mm
Quality class: 1/2H /Wall thickness 0.3 mm /Wall thickness 0.25
Specified minimum tensile or over up to and incl. mm or over up to and
strength 30 mm] incl. 25 mm]
Table B.3 (continued) 270 [Outer diameter 4 mm 270 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1565 250 mm 250 mm
Quality class: 1/2H /Wall thickness 0.15 /Wall thickness 0.15
Specified minimum tensile mm or over up to and mm or over up to and
strength incl. 30 mm] incl. 25 mm]

(continued)

－10－
 B 8265:2010 ERRATA (6/11)

Page Position Error Correct

83 Table B.3 (continued) 305 [Outer diameter 4 mm 305 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1862 250 mm 250 mm
Quality class: 1/2H /Wall thickness 0.15 /Wall thickness 0.15
Specified minimum tensile mm or over up to and mm or over up to and
strength incl. 30 mm] incl. 25 mm]
84 Table B.3 (continued) C5010T-1/2H C5010T-1/2H
Type: JIS H 3300 C5010T-1/2H C5010TS-1/2H
Model: 5010
Quality class: 1/2H
Designation
(at two positions: one in the
fourth column from the left,
the other in the rightmost
column)
Table B.3 (continued) 270 [Outer diameter 4 mm 270 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 5010 250 mm 250 mm
Quality class: 1/2H /Wall thickness 0.15 /Wall thickness 0.15
Specified minimum tensile mm or over up to and mm or over up to and
strength incl. 30 mm] incl. 25 mm]
Table B.3 (continued) 295 [Outer diameter 4 mm 295[Outer diameter 4 mm or
Type: JIS H 3300 or over up to and incl. over up to and incl. 250
Model: 1565 250 mm mm
Quality class: 3/4H /Wall thickness 0.15 /Wall thickness 0.15
Specified minimum tensile mm or over up to and mm or over up to and
strength incl. 30 mm] incl. 25 mm]
Table B.3 (continued) C1862T-3/4H C1862T-3/4H
Type: JIS H 3300 C1862T-3/4H C1862TS-3/4H
Model: 1862
Quality class: 3/4H
Designation
(at two positions: one in the
fourth column from the left,
the other in the rightmost
column)
Table B.3 (continued) 325 [Outer diameter 4 mm 325 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 1862 250 mm 250 mm
Quality class: 3/4H /Wall thickness 0.15 /Wall thickness 0.15
Specified minimum tensile Mm or over up to and mm or over up to and
strength incl. 30 mm] incl. 25 mm]

(continued)

－11－
 B 8265:2010 ERRATA (7/11)

Page Position Error Correct

84 Table B.3 (continued) C5010T-3/4H C5010T-3/4H
Type: JIS H 3300 C5010T-3/4H C5010TS-3/4H
Model: 5010
Quality class: 3/4H
Designation
(at two positions: one in the
fourth column from the left,
the other in the rightmost
column)
Table B.3 (continued) 295 [Outer diameter 4 mm 295 [Outer diameter 4 mm
Type: JIS H 3300 or over up to and incl. or over up to and incl.
Model: 5010 250 mm 250 mm
Quality class: 3/4H /Wall thickness 0.15 /Wall thickness 0.15
Specified minimum tensile mm or over up to and mm or over up to and
strength incl. 30 mm] incl. 25 mm]
Table B.3 (continued) 315 [Outer diameter 25 mm 315 [Outer diameter 25 mm
Type: JIS H 3300 or over up to and incl. or under
Model: 1020 100 mm /Wall thickness 0.25
Quality class: H /Wall thickness 0.3 mm mm or over up to and
Specified minimum tensile or over up to and incl. 6 incl. 3 mm]
strength mm] 315 [Outer diameter over 25
mm up to and incl. 50
mm
/Wall thickness 0.9 mm
or over up to and incl. 4
mm]
315 [Outer diameter over 50
mm up to and incl. 100
mm
/Wall thickness 1.5 mm
or over up to and incl. 6
mm]
Table B.3 (continued) 315 [Outer diameter 25 mm 315 [Outer diameter 25 mm
Type: JIS H 3300 or under or under
Model: 1201, 1220 /Wall thickness 0.3 mm /Wall thickness 0.25
Quality class: H or over up to and incl. 3 mm or over up to and
Specified minimum tensile mm incl. 3 mm]
strength /Outer diameter over 315 [Outer diameter over 25
25 mm up to and incl. mm up to and incl. 50
50 mm mm
/Wall thickness 0.9 mm /Wall thickness 0.9 mm
or over up to and incl. 4 or over up to and incl. 4
mm mm]
/Outer diameter over 315 [Outer diameter over 50
50 mm up to and incl. mm up to and incl. 100
100 mm mm
/Wall thickness 1.5 mm /Wall thickness 1.5 mm
or over up to and incl. 6 or over up to and incl. 6
mm] mm]

(continued)

－12－
 B 8265:2010 ERRATA (8/11)

Page Position Error Correct

84 Table B.3 (continued) 400 [Outer diameter 51 mm 400 [Outer diameter 25 mm
Type: JIS H 3300 or under or under
Model: 1565 /Wall thickness 0.15 /Wall thickness 0.15
Quality class: H mm or over up to and
Specified minimum tensile mm or over up to and
incl. 4 mm]
strength incl. 3 mm]
400 [Outer diameter over 25
mm up to and incl. 51
mm
/Wall thickness 0.15
mm or over up to and
incl. 4 mm]
Table B.3 (continued) C1862T-H C1862T-H
Type: JIS H 3300 C1862T-H C1862TS-H
Model: 1862
Quality class: H
Designation
(at four positions: two in the
fourth column from the left,
the other two in the rightmost
column)
Table B.3 (continued) 450 [Outer diameter 51 mm 450 [Outer diameter 25 mm
Type: JIS H 3300 or under or under
Model: 1862 /Wall thickness 0.15 /Wall thickness 0.15
Quality class: H mm or over up to and mm or over up to and
Specified minimum tensile incl. 4 mm] incl. 3 mm]
strength 450 [Outer diameter over 25
mm up to and incl. 51
mm
/Wall thickness 0.15
mm or over up to and
incl. 4 mm]
Table B.3 (continued) C5010T-H C5010T-H
Type: JIS H 3300 C5010T-H C5010TS-H
Model: 5010
Quality class: H
Designation
(at four positions: two in the
fourth column from the left,
the other two in the rightmost
column)

(continued)

－13－
 B 8265:2010 ERRATA (9/11)

Page Position Error Correct

84 Table B.3 (continued) 400 [Outer diameter 51 mm 400 [Outer diameter 25 mm
Type: JIS H 3300 or under or under
Model: 5010 /Wall thickness 0.15 /Wall thickness 0.15
Quality class: H mm or over up to and mm or over up to and
Specified minimum tensile incl. 4 mm]
incl. 3 mm]
strength 400 [Outer diameter over 25
mm up to and incl. 51
mm
/Wall thickness 0.15
mm or over up to and
incl. 4 mm]
102 Table B.4 Type 3 < 63 Type 3 ≤ 63
Type: JIS G 4107
Model dimensions
112 Table C.14 (concluded) N06002 N06022
Standard composition:
55Ni-21Cr-13.5Mo
Grade symbol
115 Table D.1 (continued) 101 110
Type of materials: Titanium
alloy Type 61
Longitudinal elastic
coefficient of materials at
each temperature, 20
199 F.9 The large diameter hole The large diameter hole
shall be reinforced as given shall be reinforced as given
in a) to b) below. in a) to c) below.
216 Figure G.2 b) 4) Replace the existing figure with the correct one as shown
below.
Error Correct

Taper over 1/3 1.5g0 min.

Taper over 1/3 1.5g0 min.

Taper 1/3 or under

Taper 1/3 or under

Weld centre
Weld centre

（ : Corrected position）

(continued)

－14－
 B 8265:2010 ERRATA (10/11)

Page Position
250 Figure I.2 a) 3) Replace the existing figure with the correct one as shown
below.
Error Correct

min.

max. min. max. min.

（ : Corrected position）
Page Position
253 Figure I.4 Replace the existing figure with the correct one as shown
below.
Error Correct

Metal to
metal contact Metal to metal contact
Flange II

Flange II
Flange I

Flange I

（ : Corrected position）
Page Position Error Correct
267 L.3.2 The calculated thickness of The calculated thickness of
the bolted flat cover plate the bolted flat cover plate
shall be as given in a) to c) shall be as given in a) to d).
below.
273 M.1 This Annex applies to the This Annex applies to the
calculation of plates of calculated thickness of plates
pressure vessels…. of pressure vessels….

(continued)

－15－
 B 8265:2010 ERRATA (11/11)

Page Position
274 Figure M.1 b) Replace the existing figure with the correct one as shown
below.
Error Correct

（ : Corrected position）
Page Position Error Correct
277 M.5 c) The load by which….the total area The load by which….the total area
occupied by the tube hole from the occupied by the tube hole and the area
area supported by the tube occupied by the stay tube from the area
stay,….. supported by the tube stay,…..
M.6 σa: allowable tensile stress of the σa: allowable tensile stress of the
material…..However, in the material…..However, in the case of
case of stays that are fixed by stays having welds, it shall be the
welding, it shall be the allowable tensile stress of the
allowable tensile stress of the material of the stay….
material of the stay….
284 Figure O.2 Meanings of symbols used in the Meanings of symbols used in the
Below b) figures: figures:
…… ……
The position of the notch to be The position of the notch to be
given….the thermally affected given….the thermally affected area.
area. When taking two test pieces in the case
of welding metal over 38 mm in
thickness, in addition to the one shown
in the figure, another shall be taken at
the opposite side of the base metal such
that the test piece axis is at 0.25 t from
the base metal surface.

(concluded)

－16－