H 046 000617 00 8 0 - DP 6900 Ops Manual Basic Volume

DP-6900
Digital Ultrasonic Diagnostic

Imaging System
Operator’s Manual
[Basic Volume]
Contents
Intellectual Property Statement .......................................................................................................... I
Responsibility on the Manufacturer Party .......................................................................................... I
Warranty ............................................................................................................................................ II
Exemptions................................................................................................................................... II
Customer Service Department .................................................................................................... III
Important Information ....................................................................................................................... III
About This Manual ........................................................................................................................... IV
Notation Conventions ....................................................................................................................... IV
Operator’s Manuals .......................................................................................................................... IV
Manuals on Paper ............................................................................................................................ IV
Software Interfaces in this Manual ................................................................................................... IV
Conventions ...................................................................................................................................... V
Safety Precautions .............................................................................................................. VI

Meaning of Signal Words ................................................................................................................. VI
Meaning of Safety Symbols.............................................................................................................. VI
Safety Precautions ........................................................................................................................... VI
Latex Alert ....................................................................................................................................... XII
Warning Labels............................................................................................................................... XIII
1 Overview ...................................................................................................................... 1-1

1.1 General ................................................................................................................................. 1-1
1.2 Product Specifications .......................................................................................................... 1-1
1.2.1 Environmental Conditions ............................................................................................. 1-1
1.2.2 Dimensions and Weight ................................................................................................ 1-1
1.3 System Configuration ........................................................................................................... 1-2
1.3.1 Standard Configuration ................................................................................................. 1-2
1.3.2 Transducers Available .................................................................................................. 1-2
1.3.3 Optional Parts ............................................................................................................... 1-3
1.3.4 Peripherals Supported .................................................................................................. 1-3
1.4 System Introduction.............................................................................................................. 1-4
1.4.1 Introduction of Each Unit .............................................................................................. 1-4
1.4.2 I/O Panel ....................................................................................................................... 1-6
1.4.3 Control Panel ................................................................................................................ 1-7
1.4.4 Symbols ........................................................................................................................ 1-9
2 Preparing the System ................................................................................................. 2-1

2.1 Setup and Connections ........................................................................................................ 2-1
2.1.1 Moving and Placing the System ................................................................................... 2-1
Contents i
2.1.2 Connecting the Power Cord.......................................................................................... 2-1
2.1.3 Connecting/Disconnecting the Transducers ................................................................. 2-2
2.1.4 Connecting/Disconnecting USB device ........................................................................ 2-3
2.1.5 Connecting a Footswitch............................................................................................... 2-3
2.1.6 Connecting a Printer ..................................................................................................... 2-3
2.1.7 Connecting an External Display.................................................................................... 2-4
2.2 Powering ON/OFF ................................................................................................................ 2-4
2.2.1 Checking before Powering ON ..................................................................................... 2-4
2.2.2 Powering ON................................................................................................................. 2-5
2.2.3 Restarting ...................................................................................................................... 2-5
2.2.4 Powering OFF ............................................................................................................... 2-5
2.3 Main Interface ....................................................................................................................... 2-6
2.4 Basic Operations .................................................................................................................. 2-7
3 Beginning an Exam ..................................................................................................... 3-1

3.1 Entering Patient Information ................................................................................................. 3-1
3.2 Getting Patient Information ................................................................................................... 3-2
3.2.1 iStation .......................................................................................................................... 3-2
3.2.2 Work List ....................................................................................................................... 3-3
3.3 Selecting the Exam Mode .................................................................................................... 3-3
3.4 Selecting the Image Mode .................................................................................................... 3-3
3.5 Adjusting the Image .............................................................................................................. 3-4
3.5.1 Zooming ........................................................................................................................ 3-4
3.5.2 Zooming with Thumbnail ............................................................................................... 3-4
3.5.3 Rotating and Flipping the Image ................................................................................... 3-4
3.5.4 Image Merge ................................................................................................................. 3-5
3.6 Cine Review ......................................................................................................................... 3-5
3.6.1 Cine Review of B Mode ................................................................................................ 3-5
3.6.2 Cine Review of 2B/4B Mode ......................................................................................... 3-6
3.6.3 Cine Review of M/M+B Mode ....................................................................................... 3-6
3.7 Brief Introductions to Measurement ..................................................................................... 3-6
3.7.1 Basic Operations and Buttons ...................................................................................... 3-7
3.7.2 Measurement Items ...................................................................................................... 3-8
4 Optimizing the Image .................................................................................................. 4-1

4.2 B Mode ................................................................................................................................. 4-2
4.2.1 Depth ............................................................................................................................ 4-2
4.2.2 Frequency ..................................................................................................................... 4-2
4.2.3 Gain .............................................................................................................................. 4-3
4.2.4 Acoustic Power ............................................................................................................. 4-3
ii Contents
4.2.5 TGC .............................................................................................................................. 4-4
4.2.6 Focus ............................................................................................................................ 4-4
4.2.7 B/M Dyn Rng (Dynamic Range) ................................................................................... 4-5
4.2.8 Img Enhance (Image Enhance) .................................................................................... 4-5
4.2.9 Frame Avg (Frame Average) ........................................................................................ 4-5
4.2.10 TSI ................................................................................................................................ 4-6
4.2.11 Scan Mode.................................................................................................................... 4-6
4.2.12 IP................................................................................................................................... 4-7
4.2.13 B/M Post Process ......................................................................................................... 4-7
4.3 M Mode ................................................................................................................................ 4-9
4.3.1 M Speed........................................................................................................................ 4-9
4.3.2 Edge Enhance .............................................................................................................. 4-9
4.3.3 M Soften ..................................................................................................................... 4-10
5 Annotating the Image ................................................................................................. 5-1

5.1 Comments ............................................................................................................................ 5-1
5.1.1 Adding Comments ........................................................................................................ 5-1
5.1.2 Adding Arrow ................................................................................................................ 5-2
5.1.3 Moving Comments/Arrows............................................................................................ 5-2
5.1.4 Editing Comments ........................................................................................................ 5-2
5.1.5 Deleting Comments/Arrows .......................................................................................... 5-2
5.2 Body Mark ............................................................................................................................ 5-3
5.2.1 Adding Body Mark ........................................................................................................ 5-3
5.2.2 Moving the Body Mark .................................................................................................. 5-3
5.2.3 Editing the Body Mark .................................................................................................. 5-3
5.2.4 Deleting the Body Mark ................................................................................................ 5-3
6 Auxiliary Functions .................................................................................................... 6-1

6.1 Biopsy Guide ........................................................................................................................ 6-1
6.1.1 Basic Operations .......................................................................................................... 6-1
6.1.2 Adjusting the Guide Line .............................................................................................. 6-1
6.2 Lithotrity ................................................................................................................................ 6-2
7 File Management......................................................................................................... 7-1

7.1 Formats of Files.................................................................................................................... 7-1
7.2 Saving Files .......................................................................................................................... 7-1
7.3 File Management.................................................................................................................. 7-1
7.4 iVision ................................................................................................................................... 7-3
8 Probes and Biopsy ..................................................................................................... 8-1

8.1 Probes .................................................................................................................................. 8-1
8.1.1 Name and Function of Each Part of the Probe............................................................. 8-3
Contents iii
8.1.2 Orientation of the Ultrasound Image and the Probe Head ........................................... 8-5
8.1.3 Procedures for Operating ............................................................................................. 8-6
8.1.4 Wearing the Probe Sheath ........................................................................................... 8-9
8.1.5 When the Immersion Method is Used (65EL60EA) .................................................... 8-10
8.1.6 Probes Cleaning and Disinfection............................................................................... 8-14
8.1.7 Storage and Transportation ........................................................................................ 8-17
8.2 Biopsy Guide ...................................................................................................................... 8-19
8.2.1 Needle-guided Brackets.............................................................................................. 8-21
8.2.2 Basic Procedures for Biopsy Guiding ......................................................................... 8-28
8.2.3 Needle-guided Bracket Inspection and Installation .................................................... 8-29
8.2.4 Verifying the Biopsy Guide Line .................................................................................. 8-34
8.2.5 Removing the Needle-guided Bracket ........................................................................ 8-35
8.2.6 Clean and Sterilize the Needle-guided Bracket .......................................................... 8-38
8.2.7 Storage and Transportation ........................................................................................ 8-39
8.2.8 Disposal ...................................................................................................................... 8-39
9 Preset ........................................................................................................................... 9-1

9.2 System Preset ...................................................................................................................... 9-2
9.2.1 Region ........................................................................................................................... 9-2
9.2.2 General ......................................................................................................................... 9-3
9.2.3 Image Preset................................................................................................................. 9-3
9.2.4 Meas Param.................................................................................................................. 9-4
9.2.5 OB ................................................................................................................................. 9-5
9.2.6 Key Config .................................................................................................................... 9-5
9.2.7 Option ........................................................................................................................... 9-6
9.3 Exam Preset ......................................................................................................................... 9-6
9.3.1 Exam Selection ............................................................................................................. 9-6
9.3.2 Exam Config ................................................................................................................. 9-7
9.4 Image Preset ........................................................................................................................ 9-7
9.5 Measure Preset .................................................................................................................... 9-9
9.5.1 Measure ........................................................................................................................ 9-9
9.6 Comment Preset................................................................................................................. 9-10
9.6.1 Comment Library ........................................................................................................ 9-11
9.7 DICOM ................................................................................................................................ 9-15
9.8 Manage Settings................................................................................................................. 9-16
9.9 Maintenance ....................................................................................................................... 9-16
10 Network Print ............................................................................................................. 10-1

10.1 Application Software on PC End ........................................................................................ 10-1
10.2 Network Print ...................................................................................................................... 10-1
iv Contents
11 Cleaning and Maintaining the System .....................................................................11-1
11.1 Daily Maintenance .............................................................................................................. 11-1
11.1.1 Cleaning the System .................................................................................................. 11-1
11.1.2 Backup of Data ........................................................................................................... 11-2
11.2 Maintenance Checks by Service Engineer ........................................................................ 11-2
11.3 Consumables and Periodic Part Replacement .................................................................. 11-2
11.4 Troubleshooting .................................................................................................................. 11-2
12 Acoustic Output ........................................................................................................ 12-1

12.1 Concerns with Bioeffects .................................................................................................... 12-1
12.2 Prudent Use Statement ...................................................................................................... 12-1
12.3 ALARA Principle (As Low As Reasonably Achievable) ...................................................... 12-1
12.4 Measurement Uncertainty .................................................................................................. 12-2
12.5 Limits of Acoustic Output .................................................................................................... 12-2
12.6 Parameters Affecting Acoustic Power ................................................................................ 12-2
12.7 Acoustic Power Setting ...................................................................................................... 12-2
12.8 Operations That Change Acoustic Output Power .............................................................. 12-3
12.9 References for Acoustic Power and Safety ........................................................................ 12-3
Appendix A Accuracy of Measurement .................................................................... A-1

Appendix B Safety Classification .............................................................................. B-1
Appendix C Guidance and Manufacturer's Declaration .......................................... C-1
Appendix D Electrical Safety Inspection .................................................................. D-1
Contents v
© 2009-2014 Shenzhen Mindray Bio-Medical Electronics Co., Ltd. All rights Reserved.
For this Operator’s Manual, the issue date is 2014-02.
Intellectual Property Statement

SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS CO., LTD. (hereinafter called Mindray)
owns the intellectual property rights to this Mindray product and this manual. This manual may
refer to information protected by copyright or patents and does not convey any license under the
patent rights or copyright of Mindray, or of others.
Mindray intends to maintain the contents of this manual as confidential information. Disclosure of
the information in this manual in any manner whatsoever without the written permission of Mindray
is strictly forbidden.
Release, amendment, reproduction, distribution, rental, adaptation, translation or any other

derivative work of this manual in any manner whatsoever without the written permission of Mindray
is strictly forbidden.
， , , , , BeneView, WATO,
BeneHeart, are the trademarks, registered or otherwise, of Mindray in China and other
countries. All other trademarks that appear in this manual are used only for informational or
editorial purposes. They are the property of their respective owners.
Responsibility on the Manufacturer Party

Contents of this manual are subject to change without prior notice.
All information contained in this manual is believed to be correct. Mindray shall not be liable for
errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this manual.
Mindray is responsible for the effects on safety, reliability and performance of this product, only if:
z all installation operations, expansions, changes, modifications and repairs of this product
are conducted by Mindray authorized personnel;
z the electrical installation of the relevant room complies with the applicable national and
local requirements; and
z the product is used in accordance with the instructions for use.
Note
This equipment must be operated by skilled/trained clinical professionals.
Warning
It is important for the hospital or organization that employs this equipment to carry out a
reasonable service/maintenance plan. Neglect of this may result in machine breakdown or
personal injury.
Safety Precautions I
Warranty
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE.
Exemptions
Mindray's obligation or liability under this warranty does not include any transportation or other
charges or liability for direct, indirect or consequential damages or delay resulting from the
improper use or application of the product or the use of parts or accessories not approved by
Mindray or repairs by people other than Mindray authorized personnel.
This warranty shall not extend to:

Malfunction or damage caused by improper use or man-made failure.
Malfunction or damage caused by unstable or out-of-range power input.
Malfunction or damage caused by force majeure such as fire and earthquake.
Malfunction or damage caused by improper operation or repair by unqualified or
unauthorized service people.
Malfunction of the instrument or part whose serial number is not legible enough.
Others not caused by instrument or part itself.
II Safety Precautions
Customer Service Department
Manufacturer: Shenzhen Mindray Bio-medical Electronics Co., Ltd.

Address: Mindray Building,Keji 12th Road South,High-tech industrial
park,Nanshan,Shenzhen 518057,P.R.China
Website: www.mindray.com
E-mail Address: service@mindray.com
Tel: +86 755 81888998
Fax: +86 755 26582680
Mindray DS USA, Inc.
800 MacArthur Blvd.
Mahwah, NJ 07430-0619 USA
Tel: +1(201) 995-8000
Toll Free: +1 (800) 288-2121
Fax: +1 (800) 926-4275
Important Information
1. It is the customer’s responsibility to maintain and manage the system after delivery.
2. The warranty does not cover the following items, even during the warranty period:
(1) Damage or loss due to misuse or abuse.
(2) Damage or loss caused by Acts of God such as fires, earthquakes, floods, lightning, etc.
(3) Damage or loss caused by failure to meet the specified conditions for this system, such as
inadequate power supply, improper installation or environmental conditions.
(4) Damage or loss due to use of the system outside the region where the system was
originally sold.
(5) Damage or loss involving the system purchased from a source other than Mindray or its
authorized agents.
3. This system shall not be used by persons other than fully qualified and certified medical
personnel.
4. Do not make changes or modifications to the software or hardware of this system.
5. In no event shall Mindray be liable for problems, damage, or loss caused by relocation,
modification, or repair performed by personnel other than those designated by Mindray.
6. The purpose of this system is to provide physicians with data for clinical diagnosis.
It is the physician’s responsibility for diagnostic procedures. Mindray shall not be liable for the
results of diagnostic procedures.
7. Important data must be backed up on external memory media.
8. Mindray shall not be liable for loss of data stored in the memory of this system caused by
operator error or accidents.
9. This manual contains warnings regarding foreseeable potential dangers, but you shall always
be alert to dangers other than those indicated as well. Mindray shall not be liable for damage
or loss that results from negligence or from ignoring the precautions and operating instructions
described in this operator’s manual.
Safety Precautions III

10. If the manager for this system is changed, be sure to hand over this operator’s manual to the
new manager.
About This Manual

This operator’s manual describes the operating procedures for digital ultrasonic diagnostic imaging
system DP-6900. To ensure safe and correct operations, carefully read and understand the manual
before operating the system.
Notation Conventions
In this operator’s manual, the following words are used besides the safety precautions (refer to
"Safety Precautions"). Please read this operator’s manual before using the system.
CAUTION: 1. United States federal law restricts this device to be sale by or on the
order of a physician.
2. The digital ultrasonic diagnostic imaging system is not intended for
ophthalmic use. Its use in this clinical specialty is contraindicated.
Operator’s Manuals
You may receive multi-language manuals in compact disc or paper. Please refer to English manual
for latest information and register information.
The content of the operator manual, such as screens, menus or descriptions, may be different from
what you see in your system. The content varies depending upon the software version, options
and configuration of the system.
Manuals on Paper
z Operator’s Manual [Basic Volume]: Describes the basic functions and operations of the
system, safety precautions, exam modes, imaging modes, preset, maintenance and
acoustic output, etc.
z Operator’s Manual [Advanced Volume]: Describes measurement preset, measurements
and calculations, etc.
z Operator’s Manual [Acoustic Power Data and Surface Temperature Data]: Contains data
tables of acoustic output for transducers.
z Operation Note: Contains quick guide for basic operations of the system.
Software Interfaces in this Manual

Depending on the software version, preset settings and optional configuration, the actual
interfaces may be different from those in this manual.
IV Safety Precautions
Conventions
In this manual, these conventions are used to describe the buttons on the control panel, the items
in menu, buttons in dialog box and some basic operations:
z <Buttons>: The angular bracket indicates buttons on control panel.
z [Items in menu and buttons in dialog box]: The square bracket indicates items in menu or
buttons in dialog box.
z Click [Items or Button]: Move the cursor to the item or button and press <Set>.
z [Items in Menu]Æ[Items in Submenu]: Selects a submenu item following the path.
z [Dyn Rng (Value)]: Indicates menu items with parameter, (value) shows the current value
of the item.
z <Multifunctional Knob (R)> and <Multifunctional Knob (L)>: Indicate the right and left
multifunctional knobs.
Safety Precautions V
Safety Precautions
Meaning of Signal Words

In this operator’s manual, the signal words DANGER, WARNING, CAUTION
and NOTE are used regarding safety and other important instructions. The signal words and their
meanings are defined as follows. Please understand their meaning before reading this manual.
Signal words Meaning
DANGER Indicates an imminently hazardous situation that, if not avoided, will

result in death or serious injury.
WARNING Indicates a potentially hazardous situation that, if not avoided, could

result in death or serious injury.
CAUTION Indicates a potentially hazardous situation that, if not avoided, may

result in minor or moderate injury.
NOTE Indicates a potentially hazardous situation that, if not avoided, may result in
property damage.
Meaning of Safety Symbols

Symbols Description
Type-BF applied part
The ultrasound transducers connected to this system are Type-BF applied parts.
"Attention" indicates the points that you should pay attention to. Be sure to read
the operator’s manual concerning these points before using the system.
Safety Precautions
Please observe the following precautions to ensure patient’s and operator’s safety when using this
system.
DANGER: Do not use flammable gasses, such as anesthetic gas or hydrogen, or

flammable liquids such as ethanol, near this system and probes,
because there is danger of explosion.
WARNING: 1. Connect the adapter power plug of this system and power plugs of
the peripherals to wall receptacles that meet the ratings indicated
on the rating nameplate. Using a multifunctional receptacle may
affect the system grounding performance, and cause the leakage
current to exceed safety requirements.
You must use the power adapter provided with the system;
otherwise electric shock may result.
VI Safety Precautions
2. Use the printing cable provided with this system to connect the
printer. Electric shock may result.
3. Before cleaning the system, disconnect the power cord from the
outlet. System failure and electric shock may result.
4. Use the transducer carefully. In case that the body contacts the
scratched transducer surface, immediately stop using the
transducer and contact the Mindray sales office, customer service
department or representative. There is risk of electric shock if
using the scratched transducer.
5. This system is not water-proof. Do not use this system in any
place where water leakage may occur. If any water is sprayed on or
into the system, electric shock may result. If water is accidentally
sprayed on or into the system, contact Mindray Customer Service
Department or sales representative.
6. Do not allow the patient to contact the live parts of the digital
ultrasonic diagnostic imaging system or other devices, e.g. signal
I/O ports. Electric shock may occur.
7. Do not use an aftermarket transducer other than those specified
by Mindray. The transducers may damage the system causing a
profound failure, e.g. a fire in the worst case.
8. Do not subject the transducers to knocks or drops. Use of a
defective transducer may cause an electric shock.
9. Do not open the shell or front panel. If open the shell when the
machine is powered on, there may be a short circuit or electric
shock.
10. Do not use this system at the same time with other equipment
such as electric knife, high-frequency therapy equipment and
defibrillator, etc., Otherwise there is a danger of electric shock.
11. Precautions during transportation: When moving the equipment,
first turn it off and close up the keyboard, then disconnect it with
other devices (including transducer), disconnect it with power
supply, and wrap the power cable on the winding rack, finally lift it
carefully by handle and move it to a proper position.
12. Accessory equipment connected to the analog and digital
interfaces must comply with the relevant IEC standards (e.g., IEC
60950 information technology equipment safety standard and IEC
60601-1 medical equipment standard). Furthermore all
configurations must comply with the standard IEC60601-1-1. It is
the responsibility of the person, who connects additional
equipment to the signal input or output ports and configures a
medical system, to verify that the system complies with the
requirements of IEC60601-1-1. If you have any questions regarding
these requirements, consult your sales representative.
13. Prolonged and repeated use of keyboards may result in hand or
arm nerve disorders for some individuals. Observe the local safety
or health regulations concerning the use of keyboards.
14. When using intra-cavity transducers, do not activate the
transducer outside the patient’s body.
Safety Precautions VII

CAUTION: 1. Precautions concerning clinical examination techniques:
(1) This system must be used only by qualified medical professionals.
(2) This operator’s manual does not describe clinical examination
techniques. The clinician should select the proper examination
techniques based on specialized training and clinical experience.
2. Malfunctions due to radio wave:
(1) If a radio wave emitting device is used in the proximity of this
system, it may interfere with operations. Do not bring or use devices
that generate radio waves, such as cellular telephones,
transceivers, and radio controlled toys, in the room where the
system is installed.
(2) If a person brings a device that generates radio waves near the
system, ask him / her to immediately turn OFF the device.
3. Precautions concerning movement of the system:
(1) When you place the system on the mobile trolley and move them
together, you must secure all objects on the mobile trolley to
prevent them from falling. Otherwise you should separate the
system from the mobile trolley and move them individually.
(2) When you have to move the system with the mobile trolley upward
or downward the stairs, you must separate them first and then move
them individually.
(3) Object placed on the monitor may fall and injure an individual.
(4) Fasten and fully secure any peripheral device before moving the
system. A loose peripheral device may fall and injure an individual.
(5) Do not expose the system to excessive vibration through
transportation. Mechanical damage may result.
(6) Always keep the system dry. Avoid transporting this system quickly
from a cold place to a warm place; otherwise condensation or water
droplets may form allowing a short circuit and possible electric
shock.
4. If the circuit protector is tripped, it indicates that the system or a
peripheral device was improperly shut down and the system is unstable.
You cannot repair the system under this circumstance and must call the
Mindray Customer Service Department or sales representative.
5. There is no risk of high-temperature burns during routine ultrasound
examinations. It is possible for the surface temperature of the
transducer to exceed the body temperature of a patient due to
environmental temperature and exam type combinations. If a patient
complains of any excessive heat from the transducer, immediately stop
scanning. To prevent patient burns, ensure there is no surface damage
to the transducer. Do not apply the transducer to the same region on
the patient for a long time. Apply the transducer only for a period of time
required for the purpose of diagnosis.
6. Do not use the system to examine a fetus for a long period of time.
7. The system and its accessories are not disinfected or sterilized prior to
delivery. The operator is responsible for the cleaning and disinfection of
transducers and sterilization of biopsy brackets according to the
manuals, prior to the use. All items must be thoroughly processed to
completely remove harmful residual chemicals or gasses that are
harmful to the human body or that may damage the accessory.
VIII Safety Precautions

8. It is necessary to press <End Exam> to end the current scan that is in
progress and clear the current Patient Information field. Otherwise new
patient data may be combined with the previous patient data.
9. Do not connect or disconnect the system’s power cord or its accessories
(e.g., a printer) without turning OFF the power first. This may damage
the system and its accessories or cause electric shock.
10. Before using the digital ultrasonic diagnostic imaging system to perform
an exam, please carefully read “10 Acoustic Output”.
11. The cover contains natural rubber latex and talc that can cause allergic
reactions in some individuals.
12. Please use the ultrasound gel compliant with the relevant local
regulations.
13. Do not connect this system to outlets with the same circuit breakers and
fuses that control the current of devices such as life-support systems. If
this system malfunctions and generates overcurrent, or when there is an
instantaneous current at power ON, the circuit breakers and fuses of the
building’s supply circuit may be tripped.
NOTE: 1. Do not use the system in the vicinity of strong electromagnetic field (such as a
transformer), which may affect the performance of the system.
2. Do not use the system in the vicinity of high-frequency radiation source, which may
affect the performance of the system or even lead to failure.
3. When using or placing the system, keep the system horizontal to avoid disbalance.
4. To avoid damaging the system, do not use it in following environment:
(1) Locations exposed to direct sunlight;
(2) Locations subject to sudden changes in environmental temperature;
(3) Dusty locations;
(4) Locations subject to vibration;
(5) Locations near heat generators;
(6) Locations with high humidity.
5. Turn ON the system only after the power has been turned OFF for more than 20
seconds. If the system is turned ON immediately after being turned OFF, the system
may not reboot properly and could malfunction.
6. Do not disconnect a transducer that remains in a live imaging state. This can
damage the system and / or transducer. Press [Freeze] key to freeze an image or
turn off the power of the system before connecting or disconnecting a transducer.
7. Remove ultrasound gel from the face of a transducer when the examination is
complete. Water in the gel may enter the acoustic lens and adversely affect or
damage the transducer array and lens.
8. You should properly back up the system to a secure external storage media,
including system configuration and settings and patient data. Data stored to the
system’s hard drive may be lost due to system failure, improper operation or
accident.
9. Do not apply external force to the control panel. The system may be damaged.
10. If the system is used in a small room, the room temperature may rise. Provide
proper ventilation and free air exchange.
Safety Precautions IX
NOTE: 11. To dispose of the system or any part, contact Mindray Customer Service Department
or sales representative. Mindray is not responsible for any system content or
accessories that have been discarded improperly.
12. To ensure optimal system operations, it is recommended that you maintain the
system under a Mindray service agreement. Various aspects of system performance
and operation can be maintained under the professional supervision of a service
representative.
13. Do not use gel, disinfectant, transducers or needle-guided brackets that are not
compatible with the system.
14. The replaceable fuse is inside the chassis. Refer replacing job to Mindray service
engineers or engineers authorized by Mindray only.
15. Do not turn OFF the power supply of the system during printing, file storage or
invoking other system operations. An interrupted process may not be completed,
and can become lost or corrupted.
16. If the system is powered off improperly during operation, it may result in data
damage or system failure.
17. Do not use a USB memory device (e.g., a USB flash drive, removable hard disk)
which has unsafe data. Otherwise system damage may result.
18. It is recommended to only use the video devices specified in this manual.
19. When using this system with portable package, be careful not to block the ventilation
slots.
20. When copying files to USB storage device, do not pull out the USB storage device
forcibly, or damage to USB storage device or this system may occur.
21. Do not connect mobile hard disk with too many partitions.
22. When sending DICOM files or copying files from USB storage devices, do not press
the buttons on the control panel.
Please read the following precautions carefully to ensure the safety of the patient and the operator
when using the probes.
WARNING: 1. This ultrasonic probe is only for use with the specified ultrasonic
diagnostic system. Please refer to “1.3.2 Transducers Available” to
select the proper probe.
2. Confirm that the probe and cable are normal before and after
each examination. A defective probe may cause electric shock to
the patient.
3. Do not subject the probe to shock. A defective probe may cause
electric shock to the patient.
4. Do not disassemble the probe to avoid the possibility of electric
shock.
5. Never immerse the probe connector into liquids such as water or
disinfectant because the connector is not waterproof. Immersion
may cause electric shock or malfunction.
6. Ultrasonic probe is only for use with the specified ultrasonic
diagnostic system. Please refer the ultrasonic diagnostic system
operation manual to select the proper probe.
7. A probe sheath must be installed over the probe before
performing intra-cavity or intra-operative examination.
X Safety Precautions
CAUTION: 1. When using the probe, wear sterile gloves to prevent infection.
2. Be sure to use ultrasound gel. Please use the ultrasound gel compliant
with the relevant local regulations.
3. In normal diagnostic ultrasound mode, there is no danger of a normal-
temperature burn; however, keeping the probe on the same region of
the patient for a long time may cause such a burn.
4. Do not use the carrying case for storing the probe. If the carrying case
is used for storage, it may become a source of infection.
5. The probe and accessories supplied with it are not delivered
disinfected or sterilized. Sterilization (or high-level disinfect) before
use is required.
6. It is required to practice ALARA when operating ultrasound system.
Minimize the acoustic power without compromising the quality of
images.
7. Disposable components are packaged sterile and are single-use only.
Do not use if integrity of packaging violated or if expiration date has
passed. Please use the disposable components compliant with the
relevant local regulations.
8. Please use the disinfection or sterilization solution that recommended
in this operator’s manual, otherwise Mindray will not be liable for
damage caused by other solutions. If you have any questions, please
contact Mindray Customer Service Department or sales representative.
9. Do not use pre-lubricated condoms as a sheath. Lubricant may not be
compatible with the transducer material and damage may result.
10. Transducer damage may be caused by inappropriate gel, detergent or
cleanser:
Do not soak or saturate transducers with solutions containing alcohol,
bleach, ammonium chloride compounds, acetone or formaldehyde.
Avoid contact with solutions or coupling gels containing mineral oil or
lanolin.
NOTE: 1. Read the following precautions to prevent the probe from malfunction.
z Before connecting or disconnecting the probe, freeze or turn off the ultrasound
diagnostic system.
z Clean and disinfect the probe before and after each examination.
z After the examination, wipe off the ultrasound gel thoroughly. Otherwise, the
ultrasound gel may solidify and the image quality would be degraded.
2. Ambient conditions:
To prevent the probe from being damaged, do not use it where it will be exposed to:
z direct sunlight or X-rays
z sudden changes in temperature
z dust
z excessive vibration
z heat generators
Use the probes under the specified ambient conditions.
3. Repeated disinfection will eventually damage the probe, please check the probe’s
performance periodically.
Safety Precautions XI
Latex Alert
WARNING: Allergic reactions in latex (natural rubber) sensitive patients may range
from mild skin reactions (irritation) to fatal anaphylactic shock, and
may include difficulty in breathing (wheezing), dizziness, shock,
swelling of the face, hives, sneezing or itching of the eyes (FDA
Medical Alert on latex products, “Allergic Reactions to Latex-
containing Medical Devices”, issued on March 29, 1991).
When choosing a transducer sheath, it is recommended that you directly contact CIVCO for
obtaining transducer cover, pricing information, samples and local distribution information. For
CIVCO information, please contact the following:
CIVCO Medical Instruments
Tel: 1-800-445-6741
WWW.civco.com
XII Safety Precautions

Warning Labels
The warning labels are attached to this system in order to call your attention to potential hazards.
The symbol on the warning labels indicates safety precautions. The warning labels use the
same signal words as those used in the operator’s manual.
Refer to the operator’s manual for detailed information about the warning labels. Read operator’s
manual carefully before using the system.
The name, pattern and meaning of each warning label are described as follows:
No. Label Meaning
Caution! Please carefully read this manual

1
before use system.
Prohibit using system with flammable

2
anesthetics, or explosion risk may happen
The following labels are available

when the system works with the a. Do not place the system on a sloped surface.
mobile trolley. Otherwise the system may slide, resulting in
personal injury or the system malfunction. Two
persons are required to move the system over a
3 sloped surface.
b. Do not sit on the system.
c. DO NOT push the system when the casters
are locked.
Medical equipment with respect to electric

shock, fire and mechanical hazards only in
4 accordance with UL60601-1, CAN/CSA-C22.2
NO.601.1-M90, IEC60601-1-1 and IEC60601-2-
37.
Safety Precautions XIII

1 Overview
This chapter introduces the basic information of the system.
1.1 General
Intended Use: DP-6900 digital ultrasonic diagnostic imaging system is applicable for ultrasonic
exams of human body.
Contraindication: none.
Product and Model Code
DP-
Model Code
Product Code
NOTE: The functions described in the operator’s manual may vary depending upon the specific
system you purchased.
1.2 Product Specifications
1.2.1 Environmental Conditions

Power Supply
Voltage: 100-240V~, fluctuation of ±10% is allowed
Frequency: 50/60Hz
Input current: 1.5-0.7A
Environment conditions
Operating Storage and transportation
Ambient temperature: 5℃~40℃ -20℃~55℃
Relative humidity: 35%~85%RH (no condensation) 30%~85%RH (no condensation)
Atmospheric pressure: 700hPa～1060hPa 700hPa~1060hPa
WARNING: Do not use this system in the conditions other than those specified.
1.2.2 Dimensions and Weight

z External dimensions: 330mm×410mm×265mm (H×L×W)
z Net weight: 10.3kg
Overview 1-1
1.3 System Configuration
1.3.1 Standard Configuration

Main unit
Accessories
z Power cord of the main unit
z Remote cable of printer
z Gel
z Operator’s manual
1.3.2 Transducers Available

Region
Model Type Intended Use
Applied
Gynecology, abdomen, pediatrics,
35C20EA Convex musculoskeletal (general), peripheral vascular, Body surface
cardiac and nerve
Gynecology, obstetrics, abdomen, pediatrics,
35C50EA Convex musculoskeletal (general), peripheral vascular, Body surface
urology and nerve
Abdomen, pediatrics, neonatal cephalic, adult
65C15EA Convex cephalic, musculoskeletal (general), pediatric Body surface
cardiac, peripheral vascular and nerve
Transvaginal
Endocavity Gynecology, obstetrics, urology and neonatal
65EC10EA Transrectal
convex cephalic
Body surface
Endocavity Urology (prostate and seminal vesicle) and
65EL60EA Transrectal
linear rectum
75L38EA Abdomen, pediatrics, small organs (such as
mammary gland, thyroid and testis), neonatal
75L53EA
Linear cephalic, musculoskeletal (general and Body surface
superficial), peripheral vascular, orthopedics and
75L60EA
nerve
Abdomen, pediatrics, small organs (such as
mammary gland, thyroid and testis), neonatal
Body surface
75LT38EA Linear cephalic, musculoskeletal (general and
Intraoperative
superficial), peripheral vascular, orthopedics,
nerve and intraoperative
1-2 Overview
1.3.3 Optional Parts
No. Name Model or Description
1 DICOM software DICOM3.0
2 Mobile trolley UMT-100
3 Portable package /
4 Spongy portable package /
5 Foot switch 971-SWNOM
6 Dust-proof film /
7 Dual-transducer socket /
8 Hard disk /
1.3.4 Peripherals Supported

No. Name Model
HP Photosmart D5368
HP Business Inkjet 1200
HP DeskJet 1280
1 Graph/text printer (USB port)
HP DeskJet 3820
HP DeskJet 5650
HP DeskJet 6548
MITSUBISHI P93W
MITSUBISHI P93W-Z
2 Video printer
SONY UP-895MD
SONY UP-897MD
WARNING: This system complies with IEC60601-1-2: 2001+A1: 2004, and its RF
emission meets the requirements of CISPR11 Class B. In a domestic
environment, the customer or the user should guarantee to connect
the system with Class B peripheral devices; otherwise RF interference
may result and the customer or the user must take adequate measures
accordingly.
NOTE: For any question about choice and use of the printers, contact Mindray customer
service department.
Overview 1-3
1.4 System Introduction
NOTE: The illustrations in the manual are for reference only. What appears in the illustrations
may vary depending upon the specific system you purchased.
1.4.1 Introduction of Each Unit
2
3
4
5
Front view
1-4 Overview
7
10
Right side view
11
12
Left side view
No. Name Function

1 Hook for transducer cable Used for hanging the transducer cable.
2 Monitor Displays images and parameters, etc.
3 Brightness knob Rotate it to adjust the brightness of the monitor.
4 Contrast knob Rotate it to adjust the contrast of the monitor.
5 Power indicator (inside) Indicates whether the power is on.
6 Power indicator (outside) Indicates whether the power is on.
7 Handle Used for carrying the machine.
Overview 1-5
No. Name Function
Transducer and gel bottle Used for holding the transducer or gel bottle
8
holder provisionally.
9 Control panel Refer to “1.4.3 Control Panel” for details.
10 Transducer socket Used for connecting a transducer.
11 Winding rack Used for winding the power cable.
12 USB port Used for connecting a USB device.
1.4.2 I/O Panel

The I/O panel locates at the back of the system.
1 8
2
3
7
4
6
No. Name Function

1 Video out (coaxial connector) Connects to the video input port of the video printer.
2 Remote Connects the remote cable of the video printer.
3 Video out (S-video) Connects to the video input port of the video printer.
4 Network port Accepts the network cable.
5 VGA out Connects an external monitor.
6 AC IN Accepts the power cord.
7 Foot switch Accepts a foot switch.
8 Power switch Power on/off
1-6 Overview
1.4.3 Control Panel
<2> <3> <4> <5> <6> <7> <8> <9> <10>

<1>
<11>
<12>
<13> <14> <15> <22>

<21>
<16> <17> <2 <27> <28> <29>
3>
0>
<2
<25>
<2
<18> <19> 4> 6> <30> <31> <32>
<2
<34>
<33> <36> <37>
<35>
<38> <39>
No. Name Function

Adjusts the acoustic power when rotated. The function when
1 A.Power
pressed can be preset. Refer to “9.2.6 Key Config” for details.
2 End Exam Ends the current exam.
3 Info Opens/closes the patient information dialog box.
4 Exam Opens the exam mode menu to select an exam mode.
5 Probe Switches transducers.
User-defined key, the function of which can be preset. Refer to
6 F5
“9.2.6 Key Config” for details.
7 File Opens iStation.
8 Setup Opens the preset menu.
9 Indicator Reserved
10 TGC Time Gain Compensation
Overview 1-7
No. Name Function
Character & number
11 Used for inputting characters and symbols.
keys
12 F4
13 F3
14 Comment Enters/exits character comment mode.
15 Arrow Enters/exits arrow comment mode.
16 F1
17 F2
18 Exit Exits a dialog box without saving changes.
Switches between auto/manual cine review modes. Releases
19 Cine
the cursor.
20 Measure Enters/exits measure mode.
21 Body Mark Adds body mark to the image.
22 Clear Clears the screen.
23 Menu Opens/closes the menu of current mode.
24 Set Selects items/Confirms an operation/Increases a parameter.
Switches among items before beginning a measurement.
25 Change
Switches between cursors during a measurement.
26 Back Cancels the last step when measuring/Decreases a parameter.
Switches to dual B mode. Or
27 Dual
Switches between windows in dual B mode.
Switches to quad B mode. Or
28 Quad
Switches among windows in quad B mode.
29 V.Rev. Flips the image vertically.
30 B Switches to B mode.
31 M Switches to M+B or M mode.
32 H.Rev. Flips the image horizontally.
Press to switch among items and rotate to adjust the
corresponding item:
Multifunctional Knob z F.Pos.: Adjusts location of the focus.
33
(L): F.Pos./Freq./IP z Freq.: Switches the transmitting frequency.
z IP: Adjusts the image quality according to a set of
preset image parameters.
34 Save Saves an image as preset format.
35 Track Ball Moves the cursor.
1-8 Overview
No. Name Function
Adjusts the gain of image when rotated. The function when
36 Gain
pressed can be preset. Refer to “9.2.6 Key Config” for details.
Press to switch among items and rotate to adjust the
corresponding item:
Multifunctional knob
37 (R): Depth/Zoom/ z Depth: Adjusts the depth.
Rotation z Zoom: Magnifies the image.
z Rotation: Rotates the arrow mark or the transducer
mark of the body mark.
38 Print Printing
39 Freeze Freezes/unfreezes the image.
1.4.4 Symbols
This system uses the symbols listed in the following table, and their meanings are explained as
well.
Symbol Description Location
Dangerous voltage Inside the machine
Main switch OFF

Power switch
│ Main switch ON
Serial number
AC (Alternating current)
Label of the machine
Date of manufacture
Manufacturer
Video printing control
Video out
VGA out
I/O panel
Foot switch
USB port
Network port
Transducer socket A
A
Transducer sockets
Transducer socket B
B
Overview 1-9
2 Preparing the System
This chapter introduces how to prepare and get familiar with the system.
2.1 Setup and Connections
2.1.1 Moving and Placing the System

Please read and understand the safety precautions before moving and placing the system.
1. Turn off the power and disconnect the peripheral devices.
2. Move the system to the desired position by holding the handle.
3. Leave at least 20cm clearance at the back and two sides of the machine.
CAUTION: Ensure enough clearance at the back and both side of the machine,
otherwise failure may happen because of the increasing temperature
inside the machine.
2.1.2 Connecting the Power Cord

Connecting the power cord
WARNING: 1. Do not connect this system to outlets with the same circuit
breakers and fuses that control current to devices such as life-
support systems. If this system malfunctions and generates an
overcurrent, or when there is an instantaneous current at power
ON, the circuit breakers and fuses of the building’s supply circuit
may be tripped.
2. Do not connect the three-wire power cable of the machine to a two-
wire plug without grounding protection phase, otherwise electric
shock may happen.
1. Ensure that the external power supply system meets the requirements and the power switch of
the system is turned off.
2. Attach the connector of the power cord to the system.
3. Insert the power plug securely into the wall outlet.
Preparing the System 2-1

2.1.3 Connecting/Disconnecting the Transducers
CAUTION: 1. Connect/disconnect the transducer only after the system power is

turned off or the image is frozen (by Freeze key), otherwise failure
may happen.
2. When connecting/disconnecting the transducer, place the
transducer on the corresponding transducer holder and hook the
transducer cable on the cable hanger to avoid accidental falling of
the transducer, which may damage the transducer.
NOTE: Use the transducer provided by Mindray only. Otherwise may damage the system and
transducer or cause a fire.
Connecting the transducer
WARNING: Prior to connecting the transducer, the user should ensure that the
transducer, cable and the connector are all in good condition (no rift or
fall-off). Electric shock may happen if using any abnormal transducer.
1. Turn off the ultrasonic system or freeze the image.
2. Check whether the lock of the transducer connector is released. If not, turn the lock
counter-clockwise to release it.
3. Keep the cable backwards and insert the transducer connector straight into the socket.
4. Turn the lock clockwise to lock the transducer connector.
5. Hang the transducer cable to the hook for transducer cable.
Front
Back
Disconnecting the transducer

1. Turn off the system or freeze the image.
2. Turn the lock of the transducer connector counter-clockwise to release the connector.
3. Pull the transducer connector straight out vertically.
4. Settle the transducer appropriately.
2-2 Preparing the System

3
Front
Back
2.1.4 Connecting/Disconnecting USB device

DO NOT directly remove a USB memory device; otherwise the USB
WARNING: memory device and / or the system may be damaged.
Connecting: When connecting a USB memory device to the system via a USB port, the
system recognizes the device automatically and a “ ” mark appears in the lower, right-
hand corner of the screen.
Disconnecting:
1. Move cursor to the “ ” mark and press <Set>. A dialog box pops up.
2. Select the device to disconnect and click [Ok]. The “ ” mark disappears and you can
remove the USB device securely.
2.1.5 Connecting a Footswitch

Plug the connector of the footswitch to the socket with the bulge of the footswitch connector
aligning with the groove of the socket.
2.1.6 Connecting a Printer

Refer to the manual of the printer for details.
Graph/Text Printer
1. Connect the graph/text printer and the ultrasonic system with a USB cable.
2. After the connection, the system identifies the printer automatically.
Video Printer
1. Turn off the ultrasonic system and the video printer.
2. Connect the input port of the video printer and the output of the ultrasonic system with the
data cable (S-Video or coaxial cable).
3. To print with the <Print> key or the footswitch, please connect the “REMOTE” port of the
video printer and the “REMOTE” port of the ultrasonic system with the remote cable.
4. Connect the power cord of the video printer.
5. Turn on the ultrasonic system and the video printer.

2.1.7 Connecting an External Display
1. Turn off the ultrasonic system and the external display.
2. Connect the VGA out of the ultrasonic system and the VGA input of the external display.
3. Turn on the ultrasonic system and the external display.
2.2 Powering ON/OFF

WARNING: To ensure safe and effective system operation, you must perform daily
maintenance and checks. If the system begins to function improperly –
immediately stop scanning. If the system continues to function
improperly – fully shut down the system and contact Mindray
Customer Service Department or sales representative. If you use the
system in a persistent improperly functioning state – you may harm
the patient or damage the equipment.
2.2.1 Checking before Powering ON

Please check whether the system and the environment meet the requirements below before
powering on the system.
No. Items Result
The temperature, relative humidity and atmospheric pressure shall meet the
1
requirements of operating conditions.
2 There shall be no condensation.
There shall be no distortion, damage or dirt on the system and peripheral
devices.
3
If any dirt is found, cleaning shall be performed as defined in section “11
Cleaning and Maintaining the System”.
4 There shall be no loose screws on the monitor or control panel.
There shall be no cable damage (e.g. power cord). Maintaining secure
5
connections to the system at all times.
The transducers and transducer cables shall be free of damage or stains.
6
See the transducer operator’s manuals for transducer cleaning and disinfection.
No miscellaneous odds and ends are allowed to be attached or affixed to the
7
control panel.
Check the power cord / power supply and all I / O ports. Ensure that all
8 connections are free from damage and remain clear of foreign object blockages.
There shall be no obstacles around the system and its air vent.
Prior to each use of a transducer, you should perform transducer cleaning and
9
disinfection as per the transducer operator’s manual.
10 The overall scanning environment and field must be clean.

2.2.2 Powering ON
If you use a transducer giving off excessive heat, it may burn the
WARNING: patient.
NOTE: When you start the system or switch between transducers, you will hear clicking sounds
– this is expected behavior.
Press the power switch at the back of the system to power on the system.
Check whether the system starts normally and check the system after powering on.
No. Items Result
1 There shall no unusual sounds or smells indicating possible overheating.
2 There shall be no persistently displayed system error message.
There shall no evident excessive noise, discontinuous, absent or black artifacts
3
in the B Mode image.
Check if there is abnormal heat on the surface of the transducer during an
4
ultrasound procedure.
The exam date and time are the same as the system date and time, and are
5
displayed correctly.
If the system time is not the same as the current time, misdiagnose may
CAUTION: occur.
2.2.3 Restarting
When any of the following abnormalities occurs with the system, the system may be able to
recover from the abnormality by power OFF/ON once again:
z An error message is displayed and does not disappear.
z The screen display is abnormal.
z The system operations are disabled.
z Restart the system to put the new software into effect.
2.2.4 Powering OFF

If you are not using the system for a long time, please shut down the system:
1. Put the transducer away.
2. Press the power switch to shut down the system.
3. Turn off all peripherals connected to the system.

2.3 Main Interface
The main interface is as above, and the functions of areas are listed below:
No. Description
1 Name of hospital, which can be preset.
2 Logo of the manufacturer
3 Patient information and the operator.
Mark of start scanning side, by which you can identify the
4
direction of the image.
5 Image zone
6 Grey scale bar
7 Mark of focus
8 Depth scale
9 Cine progress bar
10 Current exam mode
11 Prompt information
12 Mark of current mode
13 Current input method

No. Description
14 Result window of measuring mode
15 Menu zone
16 Date and time
Image parameters, type of transducer, transmitting
17 frequency and depth. is the frozen mark, which is
displayed when frozen.
2.4 Basic Operations

To move a Dialog Box
1. Move the cursor to the title of the dialog box, and the cursor turns to “ ”.
2. Press <Set> and the cursor turns to the frame of the dialog box.
3. Roll the track ball to locate the frame of the dialog box to the anticipated area.
4. Press <Set> to confirm moving the dialog box or press <Back> to cancel.

3 Beginning an Exam
This chapter introduces the basic procedures and operations of an ultrasonic exam.
3.1 Entering Patient Information

Although you can start scanning a patient without entering patient information, it is recommended
to enter patient information before an examination is started.
CAUTION: Before examining a new patient, press the [End Exam] key to end the
exam of the previous patient, update the patient ID and information, to
avoid mixing data of the next new patient.
To open the “Patient Info” dialog box:

z Press <Info> to open the “Patient Info” dialog box.
z Click the patient information area in the left top corner of the screen to open the “Patient
Info” dialog box.
To close the “Patient Info” dialog box:
In the “Patient Info” dialog box,
z Click [Ok] or press <Info> again to save the patient information and close the “Patient Info”
dialog box.
z Click [Cancel] or press <Exit> to cancel and close the “Patient Info” dialog box.
To enter the basic information of the patient:
z Patient ID: Input the patient ID with the keyboard. The patient ID cannot be empty. Once
the patient ID is input and conformed, it cannot be modified. The patient IDs of different
patients cannot be the same as each other. If ID that already exists is input, the system
will prompt whether you want to load the patient information.
z Last Name/First Name: Input the name with keyboard.
z DOB (Date of Birth) and age:
h Input the birthday in the text box manually. Or
h Click the “ ” icon to open the date box and select the date. After the birthday is input,
the system calculates the age automatically.
z Gender: Select the gender in the drop-down list.
Information related to exam: Click the label below the basic information to switch to the
corresponding page and input information related to exam.
Beginning an Exam 3-1

3.2 Getting Patient Information
3.2.1 iStation
iStation is used to query patient information, in which the DICOM functions are only available for
systems configured with DICOM software.
To enter iStation:
z Press <Info> to open the “Patient Info” dialog box, and then click [iStation] to open the
“iStation”.
z Press <File> to open the “iStation”.
To query:
1. Selecting the data source: Select the data source in the “Data Source” drop-down list.
2. Input the query condition:
h Input the query condition in the text box on the right-hand of the corresponding
keywords.
h Select the date range in the controls behind the
3. Click [Query] and the results are displayed in the result list.
Exam Operation
In the list of results,
z [Info]: Select a record, and click [Info] to check the patient information.
z [Report]: Select a record with exam data, and click [Report] to check the exam report.
z [Delete]: To delete the selected records. To select plural patients, press <Ctrl> or <Shift>
when selecting.
z [Backup]: To backup the selected records to external storage devices when there are
external storage devices connected.
z [Restore]:
1. Select an external storage device with backup data in the drop-down list below “Data
Source”. The data are listed in the record list.
2. Select the records to be restored, and click [Restore] to restore them to the ultrasonic
system. If the records already exist, the system will prompt whether to overwrite them or
not. Select the appropriate option according to your requirements.
z [Select All]: To select all the records.
z [Send To]: To send the selected records to external storage devices.
z [DICOM Storage]: Save the DICOM files of the selected record to the preset DICOM
storage server.
z [DICOM Print]: Print the DICOM files of the selected report with the preset DICOM printer.
z Select a record of today, and click [Activate Exam] to activate the exam.
Image Operation
Select an exam, and the images included are listed in the file list below the record list. Select
an image,
z [Open]: To open the selected image.
z [Delete]: To delete the selected images.
z [Send To]: To send the selected images to external storage devices.
z [DICOM Storage]: Save the DICOM image to preset DICOM storage server.
z [DICOM Print]: Print the DICOM image with the preset DICOM printer.
3-2 Beginning an Exam

3.2.2 Work List
Work List is used to get patient information from the work list server. It is only available for systems
configured with DICOM software.
To open the “Work List” dialog box:
1. Press <Info> to open the “Patient Info” dialog box,
2. Click [Work List] in the “Patient Info” dialog box to open the “Work List” dialog box.
To query
1. Input the query conditions.
h Select the work list server.
h Select the date of exam: Input the birthday in the text box manually or click the “ ”
icon to open the date box and select the date.
h Input the query conditions.
2. Click [Query], and the results are listed in the list box below. Click [Clear] to clear the
query conditions.
3. Select a patient, and click the buttons below the list to:
h [Start Exam]: To import the patient information to system and start an exam.
h [Transfer]: To read the patient information to “Patient Info” dialog box. You can edit the
information except the ID, and then click [OK] to start an exam.
h [Show Detail]: To check the detailed information of the patient.
h [Return]: To exit Work List.
3.3 Selecting the Exam Mode

CAUTION: Once the exam mode is changed during a measurement, all the calipers
and measurement data will be cleared from the screen.
To select an exam mode
After powering on, the system selects the preset exam mode automatically. If you want to
switch to other exam modes, press <Exam> to open the exam mode menu and select an
exam mode.
To switch transducers: If two transducers are connected, press <Probe> to switch transducers.
3.4 Selecting the Image Mode

The image modes provided are as follows:
B Mode: Press <B> to enter B Mode.
z Dual B Mode: Press <Dual> to enter dual B Mode
z Quad B Mode: Press <Quad> to enter quad B Mode, and then press <Quad> to add a
new image window or switch among the image windows.
z In dual B or quad B mode, the mark can be used to identify the active window: If the
mark is white, the corresponding window is active; if the mark is grey, the
corresponding window is inactive.
M Mode
z M+B mode: Press <M> to enter M+B mode. In M+B mode, roll the trackball to adjust the
sample line.
z M mode: After setting the sample line, press <M> again to enter M mode.

3.5 Adjusting the Image
3.5.1 Zooming
This system provides a zoom range of 100%~1000%.
1. Press <Multifunctional Knob (R)> until the indicator corresponding to “Zoom” is lit up. A
viewfinder is displayed in the image window.
2. Move the viewfinder with the trackball to select the region to be magnified.
3. Rotate <Multifunctional Knob (R)> to change the magnification ratio, and the viewfinder
changes correspondingly. Rotate the multifunctional knob clockwise to increase the
magnification ratio and the viewfinder enlarges; rotate the multifunctional knob anticlockwise to
decrease the magnification ratio and the viewfinder shrinks.
4. Press <Set> and the viewfinder disappears. The magnified image is displayed. At this moment,
z Roll the track ball to pan through the image.
z Rotate <Multifunctional Knob (R)> to change the magnification ratio.
5. Press <Multifunctional Knob (R)> again to exit zoom status, and the indicator corresponding to
“Zoom” goes out.
3.5.2 Zooming with Thumbnail

To use zooming with thumbnail, enable “Display Thumbnail when Zoom” in preset first. Refer to
“9.2.3 Image Preset” for details.
1. Press <Multifunctional Knob (R)> until the indicator corresponding to “Zoom” is lit up. A
thumbnail appears in the lower, right corner of the screen.
2. Move the viewfinder in the thumbnail with the trackball to select the region to be magnified.
3. Rotate <Multifunctional Knob (R)> to change the magnification ratio, and the viewfinder
changes correspondingly. Rotate the multifunctional knob clockwise to increase the
magnification ratio and the viewfinder enlarges; rotate the multifunctional knob anticlockwise to
decrease the magnification ratio and the viewfinder shrinks.
4. Press <Multifunctional Knob (R)> again to exit zooming status, and the indicator
corresponding to “Zoom” goes out.
3.5.3 Rotating and Flipping the Image

Rotating the Image
1. Check whether the menu corresponding to the current mode is open. If not, press <Menu>
to open it.
2. Move cursor to [Rotation (Angle)]. Then press <Set> to rotate the image clockwise 90
degrees, or press <Back> to rotate the image anticlockwise 90 degrees.
Flipping the Image: Images of B mode can be flipped horizontally and vertically.
z Press <V.Rev.> to flip the image vertically;
z Press <H.Rev.> to flip the image horizontally.
Conforming the Direction of the Image
The mark in the image window is corresponding with the bulge on the transducer head (for
some transducers, it may be a groove) and it is intended for helping to identify the direction of
the image. When the image is rotated or flipped, the location of this mark changes as well.

3.5.4 Image Merge
In dual B mode, if “Image Merge” is already enabled in “PresetÆSystem PresetÆImage Preset”,
the current transducer is linear transducer, and the depth of two image windows are the same, the
system will put the two images together to extend your field of vision.
3.6 Cine Review

During the exam, press <Freeze> to freeze the image and you can review the images prior to the
image frozen.
The process bars of cine review are as follows:
B mode
Memory Memory
Used Available
Start Point of Automatic Playback 65/165
Mark of Process of Playback
End Point of Automatic Playback Frames Frames
Played in All
M mode
Memory Memory
Used Available
Start Point of Automatic Playback 1.3/3.0
Mark of Process of Playback
End Point of Automatic Playback Time Time in
Played All
3.6.1 Cine Review of B Mode

In the following conditions, the cine review memory will be cleared:
z Beginning a new exam
z Switching transducers (only the corresponding part is cleared in Dual B or Quad B mode)
z Switching among image modes
z Adjustment of some real-time image parameters (such as depth)
z Defreezing
Manual Review
Manual review is the default review mode. During an exam, press <Freeze> to freeze the
image and start reviewing. The freezing mark appears in the upper, right corner of the screen.
Here,
z Press <Menu> to open/close the Freeze Menu.
z Roll the track ball to review manually: Roll it left to review earlier images and roll it right to
review later images.
Reviewing All
1. In manual review mode, press <Cine> to release the cursor.
2. Press <Menu> to open the Freeze Menu. Then click [Review/Stop] to start reviewing, and
click [Review/Stop] again to stop reviewing.

3. To select the reviewing speed: Move cursor to [Speed (value)], and then press <Set> to
increase the reviewing speed, or press <Back> to decrease the reviewing speed.
Reviewing a Specified Segment
1. To set the start point:
(1) Review to the start point in manual mode.
(2) Press <Set> to set the start point.
2. To set the end point:
(1) Review to the end point in manual mode.
(2) Press <Change> to activate the mark of the end point and the mark turns to white.
(3) Press <Set> to set the end point.
3. To adjust the start point and end point:
(1) Press <Change> to switch between the two marks. The activated mark is white and
the inactivated mark is grey.
(2) Press <Set> to set the activated mark: the left mark will be set as start point and the
right point will be set as end point.
4. Press <Menu> to open the “Freeze Menu” or press <Cine> to release the cursor. Click
[Review/Stop] to start auto playback.
5. To select the reviewing speed: Move cursor to [Speed (value)], and then press <Set> to
increase the reviewing speed, or press <Back> to decrease the reviewing speed.
6. Click [Review/Stop] again to stop.
To Save an Image:
Press <Menu> to open the Freeze Menu. In the Freeze Menu, move the cursor to [Save As…]
and click a format in the sub menu to save image or cine files to USB storage device.
3.6.2 Cine Review of 2B/4B Mode

In Dual B/Quad B mode, the cine memory is split into 2/4 correspondingly. The basic operations
are the same as those in B mode, press <Dual>/<Quad> to activate an image window and review.
3.6.3 Cine Review of M/M+B Mode

Manual review
z Roll the trackball left to review earlier M images.
z Roll the trackball right to review later M images.
z Press <M> to switch between M+B review/M review.
3.7 Brief Introductions to Measurement

WARNING: 1. Be sure to measure areas of interest from the most optimal image
plane to avoid misdiagnosis from inaccurate measurement values.
2. If Image Merge is activated, the results of measurements over two
image windows are influenced by plural factors and they are for
reference only.

CAUTION: 1. If an image is unfrozen or the mode is changed during a
measurement, the calipers and measurement data will be cleared
from the screen. The general measurement data will be lost (the
application measurement data are stored in the report).
2. If the system is turned off or [End Exam] is selected during a
measurement, the data not saved will be lost.
3.7.1 Basic Operations and Buttons

The title bar of the measurement menu is the name of the current measurement package. If there
are more than one available measurement packages of the current exam mode, click the title bar
to switch to other packages.
Basic Buttons
<Measure>: Enters/exits measurement mode.
<Menu>: Opens/closes the measurement menu.
<Set>:
z Select an item in the measurement menu, then press <Set> to activate the measurement.
z During a measurement, press <Set> to confirm the current operation and continue.
<Change>:
z To switch among items: After activating an item and before start measuring, press
<Change> to switch among the available items.
z To switch between ends: During a measurement, press <Change> to switch between the
fixed end and the active end.
<Back>:
z During a measurement, press <Back> to cancel the last operation.
z Press <Back> continually to delete completed measurements in backward sequence.

3.7.2 Measurement Items
The measurement library of this system provides Measurement, Calculate and Study items of
General, Abdomen, Gynecology, Cardiac, Vascular, Urology, SmallPart, ORTH and Obstetric. You
can select appropriate items to create measurement packages.
The items of general measurement are listed below. For detailed information about application
measurements, please refer to [Advanced Volume].
Mode Type Item Descriptions
Distance Measures the distance between two points of interest.
Area Measures the area and perimeter of a closed region.
Angle Measures the angle between two intersected planes.
Measures the length of two line segments, which are
Cross
perpendicular to each other.
TLength Measures the length of a curve.
Measurement
Measures the distances between each pair of parallel
Parallel
lines in a sequence.
Counts the grayscale distribution of ultrasonic echo
B-Profile
2D signals across a line.
Counts the grayscale distribution of ultrasonic echo
B-Hist
signals in a closed region.
Depth Measures the depth of a spot.
Measures the lengths of any two lines and calculates the
Ratio (D)
ratio.
Calculate Volume Calculates the volume of a region.
Measures the areas of any two regions and the calculated
Ratio (A)
ratio.
Study /
Measures the time of n (n≤8) cardiac cycles and
Heart Rate
calculates the heart rate in M mode image.
Measures the distance and time between two points and
Slope
calculates the slope.
Measurement
Distance Measures the distance between two points of interest.
M
Time Measures the time interval between two points.
Calculates the average velocity by measuring the distance
Velocity
and time between two points.
Calculate /
Study /

4 Optimizing the Image
This chapter introduces how to optimizing the image by adjusting the image parameters.
Before optimizing the image by adjusting the image parameters, use the brightness and contrast
knob to adjust the monitor to the best functional mode.
The image parameters area is as follows:
Acoustic B Image Frame
B Gain M Gain Power Process Rate
Type of Frequency Depth Mark of

Transducer Freezing

Objectives Available Operations
Increase the gain.
To increase the brightness. Increase the acoustic power (do try to adjust gain
first before increasing acoustic power).
To make the brightness
Adjust TGC (Time Gain Compensation).
distribute uniformly.
To enhance the contrast. Decrease the Dyn Rng (Dynamic Range).
To observe deeper objectives. Increase the depth.
To observe shallower objectives. Decrease the depth.
Decrease the angle.
Decrease the depth.
To increase the frame rate.
Decrease the number of focuses.
Select “Hi Frm Rate” in “Scan Mode”.
Optimizing the Image 4-1

4.2 B Mode
4.2.1 Depth
Description Adjusts the image depth. Depth is available for B/M modes.
Operations Depth, Zoom and Rotation share the same knob: <Multifunctional Knob (R)>.
Press the <Multifunctional Knob (R)> to switch among the items and then rotate
the knob to adjust the item when the corresponding indicator is lit up.
The <Multifunctional Knob (R)> is in Depth mode by default. If not, press the knob
continually until the indicator corresponding to “Depth” is lit up, then rotate the
knob to adjust the depth.
The depth range varies depending on the transducer.
Effects Increase the depth, and you can see tissue in deeper locations; decrease the
depth, and you can see tissue in shallower locations.
Impacts Depth is in negative correlation with the frame rate: the larger the depth, the lower
the frame rate.
Changing depth will clear the cine memory.
Operation The image depth cannot be adjusted when the image is frozen.
Conflicts
4.2.2 Frequency
Description Adjusts the transducer transmitting frequency.
Operations Focus position (F.Pos.), frequency (Freq.) and image (IP) share the same
<Multifunctional Knob (L)>. Press the <Multifunctional Knob (L)> to switch among
the items and rotate the knob to adjust the item when the corresponding indicator
is lit up.
Press the <Multifunctional Knob (L)> until the indicator corresponding to “Freq.” is
lit up, and then rotate the knob to adjust the frequency.
The current transmitting frequency is displayed in the image parameter area.
Effects The higher the frequency, the better the axial resolution, and the worse the force of
penetration. The lower the frequency, the worse the axial resolution, and the better
the force of penetration.
For transducers that support harmonic, using harmonic (there is an “H” before the
frequency) will increase the contrast of the image.
Impacts Changing frequency will clear the cine memory.
Operation The transmitting frequency cannot be adjusted when the image is frozen.
Conflicts
4-2 Optimizing the Image

4.2.3 Gain
Description B/M gain is intended to adjust the gain of the whole receiving system and the
signal sensitivity of B/M image.
The adjusting range is 0dB~100dB. B-mode and M-mode Gains are displayed in
the Parameter Area on the top of the screen.
Operations Rotate <Gain> to adjust the gain of B image and M image.
The gain of M image can also be adjusted separately in M+B mode by using the
[M Gain] in the M image menu.
Effects Increasing the gain will brighten the image and you can see more received
signals. However, noises can also be increased.
Impacts The adjustment to gain will influence the cine review.
Operation The gain cannot be adjusted when the image is frozen.
Conflicts
4.2.4 Acoustic Power

Description Acoustic power is the transmitting power of ultrasonic wave. You should choose
the acoustic power according to “12 Acoustic Output”.
Operations Before adjusting acoustic power, please try to adjust other parameters (such as
gain) first.
Rotate <A.Power> to adjust the acoustic power. The current value of acoustic
power is displayed in the image parameter area.
Effects Changing the acoustic power will influence the brightness and contrast of the
image and the force of penetration: Generally, increasing the acoustic power will
increase the brightness and contrast of the image and the force of penetration and
vice versa.
Impacts The adjustment to acoustic power will influence the cine review.
Operation The acoustic power cannot be adjusted when the image is frozen.
Conflicts

4.2.5 TGC
Description Ultrasonic wave attenuates when transmitting inside tissue, so the received
signals of deeper tissue are weaker than those of superficial tissue. The system
compensates the signals from deeper tissue by segments to make the image of
deeper issue clear. Adjusting TGC (Time Gain Compensation) will amend the
compensation.
Operations Slide the TGC sliders on the control panel to adjust the corresponding TGC.
When toggling TGC slider, the TGC curve is displayed on the left of the screen
and changes with the movement of the slider. About 1.5s after the adjustment is
finished, the TGC curve disappears.
Effects Slide the TGC slider right to increase the compensation to this segment and the
corresponding area gets brighter. Slide the TGC slider left to decrease the
compensation to this segment and the corresponding area gets darker.
Impacts The adjustment to TGC will influence the cine review.
Operation When the image is frozen, the adjustment to TGC is unavailable temporarily and it
Conflicts takes effect after the image is defrozen.
4.2.6 Focus
Number of focuses
Description Changes the number of focuses.
Operations Press <Menu> to open B Img Menu, and move cursor to [Focus Number (num)].
Press <Set> to increase the number of focuses and press <Back> to decrease the
number of focuses.
The “X” mark in the depth scale shows a focus.
Effects /
Impacts Increasing number of focuses will decrease the frame rate.
Changing number of focuses will clear the cine memory.
Operation The number of focuses cannot be changed when the image is frozen.
Conflicts
Position of focuses
Description Changes the position of focuses.
is lit up.
Press the <Multifunctional Knob (L)> until the indicator corresponding to “F.Pos.” is
lit up, and then rotate the knob to adjust the position of focuses.
The “X” mark in the depth scale shows the current position of the focuses.
Effects /
Impacts Changing position of focuses will clear the cine memory.
Operation The position of focuses cannot be changed when the image is frozen.
Conflicts

4.2.7 B/M Dyn Rng (Dynamic Range)
Description Adjusts contrast resolution of the B Mode image to compress or expand the gray
display range. The range is 30dB~100dB and the step is 5.
Operations Press <Menu> to open B Img Menu, and move cursor to [Dyn Rng (value)]. Press
<Set> to increase the dynamic range and press <Back> to decrease the dynamic
range. The value is displayed in the menu.
Effects The less the dynamic range, the higher the contrast. The more the dynamic range,
the lower the contrast.
The image displayed may fail to match the real one when the value of Dynamic
Range is too great or too little. The recommended range is: 55~75.
Impacts The adjustment to Dynamic Range will influence the cine review.
Operation The Dynamic Range cannot be adjusted when the image is frozen.
Conflicts
4.2.8 Img Enhance (Image Enhance)

Description The range of image enhancement is 0~4. 0 represents no image enhancement
and 4 represents maximum image enhancement.
Operations Press <Menu> to open B Img Menu, and move cursor to [Img Enhance (value)].
Press <Set> to increase the image enhance and press <Back> to decrease the
image enhance. The value is displayed in the menu.
Effects /
Impacts The adjustment to image enhance will influence the cine review.
Operation The image enhance cannot be adjusted when the image is frozen.
Conflicts
4.2.9 Frame Avg (Frame Average)

Description Averages adjacent B images to smooth the image. The range of frame average is
0~7.
Frame Average is only available for B image.
Operations Press <Menu> to open B Img Menu, and move cursor to [Frame Avg (value)].
Press <Set> to increase the frame average and press <Back> to decrease the
frame average. The value is displayed in the menu.
Effects Smoothes the image.
Impacts The adjustment to frame average will influence the cine review.
Operation The frame average cannot be adjusted when the image is frozen.
Conflicts

4.2.10 TSI
Description Optimizes the image for different tissue:
Operations Press <Menu> to open B Img Menu, and move cursor to [TSI (value)]. Press
<Set> or <Back> to adjust TSI.
General: It is helpful to scan the internal organs like liver, kidney, pancreas,
thyroid, etc.
Muscle: It is helpful to scan the muscle tissue or fibrous tissue, such as
muscle, ligaments, tendon, etc.
Fatty: It is helpful to scan tissue mainly composed of fat cell, such as lipoma,
breast of old women.
Fluid: It is helpful to scan tissue mainly consist of liquid, such as gallbladder,
cyst, vessels, etc.
Effects /
Impacts Adjusting TSI will clear the cine memory.
Operation The TSI cannot be changed when the image is frozen.
Conflicts
4.2.11 Scan Mode

Scanning Angle
Description Adjusts the angle of scanning. It is available for B mode only, and the range is
0~3. 0 indicates the smallest scanning angle and 3 indicates the greatest scanning
angle.
Operations Press <Menu> to open B Img Menu, and move cursor to [Scan Mode]Æ[Scan
Angle (value)]. Then press <Set> to increase the angle and press <Back> to
decrease the angle.
Effects The larger the scan angle, the wider your field of vision. The less the scan angle,
the narrower your field of vision.
Impacts Increasing the scanning angle will widen your field of vision while lowers the frame
rate. Decreasing the scanning mode will narrow your field of vision while increases
the frame rate.
Operation The scanning angle cannot be changed when the image is frozen.
Conflicts
Scanning Mode
Description Changes the scanning mode.
Operations Press <Menu> to open B Img Menu, and move cursor to [Scan Mode]Æ[Hi
Density1/Hi Density2/Hi Frm Rate]. Then press <Set> or <Back> to select the
scanning mode.
Effects Select “Hi Density1/Hi Density2” to present clearer image and select “Hi Frm Rate”
to acquire higher frame rate.
“Hi Frm Rate” sacrifices image quality to acquire higher frame rate.
Impacts Changing scanning mode will clear the cine memory.
Operation The scanning mode cannot be changed when the image is frozen.
Conflicts

4.2.12 IP
Description IP is the combination of “Dyn Rng (Dynamic Range)”, “Image Enhance” and
“Frame Avg (Frame Average)”. The parameters can be configured separately.
is lit up.
The <Multifunctional Knob (L)> is in IP mode by default. If not, press the knob
continually until the indicator corresponding to “IP” is lit up, then rotate the knob to
adjust IP.
Effects The effect is relative with the parameters.
Impacts The adjustment to IP will influence the cine review.
Operation IP cannot be adjusted when the image is frozen.
Conflicts
4.2.13 B/M Post Process

Map
Description “Effect” of post process is the combination of “Grey Curve”, “Grey Rejection” and
“γ”. The system provides 8 effects, the parameters of which can be preset.
Operations Press <Menu> to open B Img Menu, and move cursor to [Post Process]Æ[Effect
(value)]. Then press <Set> or <Back> to select the effect.
Effects Depends on the preset parameters.

Impacts The adjustment to “Effect” will not influence the cine review.
Operation Effect can be adjusted when the image is frozen.
Conflicts

Curve
Description “Grey Curve” is used to enhance or reject signals of corresponding segment.
Operations 1. Click [Post Process]Æ[Grey Curve] of B or M image menu to open the “Grey
Curve” dialog box.
2. Move cursor to one of the nodes “·” and the cursor turns to “ ”. Press
<Set>, and then move the node “·” to adjust the grey curve with the track
ball. The image changes with the curve.
3. At this moment,
z Press <Set> again to confirm moving the node “·” and the cursor turns
back to “ ”. Repeat the procedures to adjust the next node, or
z Press <Back> to cancel moving the node “·” and the node restores to
the original position.
z Click [Linear] to reset the grey curve.
4. After the adjustment, click [OK] to confirm and exit or click [Cancel] to cancel
and exit.
Effects Enhance signals of one grey segment and the corresponding part of the image
becomes brighter. Reject signals of one grey segment and the corresponding part
of the image becomes darker.
Adjusting one node will also influence shape of adjacent segments.
Impacts The adjustment will not influence the cine review.
Operation It can be adjusted when the image is frozen.
Conflicts
Rejection
Description Suppress the image signal below a certain gray scale.
Operations 1. Click [Post Process]Æ[Grey Rejection] of B or M image menu to open the
“Grey Rejection” dialog box.
2. Move cursor to the “▲” node, and the cursor turns to “ ”. Press <Set> and
roll the track ball to move the “▲” node to adjust the grey rejection curve, and
the effect of image changes with the grey rejection.
3. At this moment,
z When getting the required effect, press <Set> to confirm and the cursor
turns back to “ ”. Or
z Press <Back> to cancel moving the node and the node returns to the
original position.
4. Click [OK] to confirm and exit or click [Cancel] to cancel and exit.
Effects The rejected segment is black.
Conflicts

γ
Description Modifies the nonlinear distortion of the image. γ correction has four grades, 0, 1, 2
and 3 corresponding to γ correction coefficients 1.0, 1.1, 1.2 and 1.3, respectively.
Operations Move cursor to [Post Process]Æ[ γ (value)], and press <Set> to increase the
value or press <Back> to decrease the value.
Effects /
Conflicts
Grey Invert: Reverse the polarity of the image. Click [Post Process]Æ[Grey Invert On/Off] to
turn on/off Bipolar Rev.
4.3 M Mode
The adjustment to Gain, Dynamic Range and Post Process are the same as those in B mode.
4.3.1 M Speed
Description Adjusts the refresh speed of M-mode image. Its range is 1~4. 1 indicates fastest
scanning speed while 4 the slowest.
Operations Press <Menu> to open the M Img Menu, and move cursor to [M Speed (1~5)].
Then press <Set> to increase the value or press <Back> to decrease the value.
Effects The greater the value of M Speed, the slower the scanning speed. The smaller the
value of M Speed, the faster the scanning speed.
Impacts Adjusting M Speed will clear the cine memory.
Operation M speed cannot be adjusted when the image is frozen.
Conflicts
4.3.2 Edge Enhance

Description The range of “Edge Enhance” is 0~4. 0 represents no Edge Enhance and 4
represents maximum Edge Enhance.
Operations Press <Menu> to open M Img Menu, and move cursor to [Edge Enhance (value)].
Press <Set> to increase the Edge Enhance and press <Back> to decrease the
Edge Enhance. The value is displayed in the menu.
Effects /
Impacts The adjustment to Edge Enhance will influence the cine review.
Operation The Edge Enhance cannot be adjusted when the image is frozen.
Conflicts

4.3.3 M Soften
Description Adds up the scanning lines of M-mode image and calculate the average value in
order to remove the noise on the image and make the image details clearer. Its
range is 0~15.
Operations Press <Menu> to open the M Img Menu, and move cursor to [M LineCorre
(0~15)]. Then press <Set> to increase the value or press <Back> to decrease the
value.
Effects Removes noises in the image.
Impacts The adjustment to M LineCorre will influence the cine review.
Operation M LineCorre cannot be adjusted when the image is frozen.
Conflicts

5 Annotating the Image
This chapter introduces how to add comments and body mark to ultrasound image.
5.1 Comments
Comments can be added to real-time image, frozen image, cine review image and zoomed image.
You must ensure that the entered comments are correct. Incorrect
WARNING: comments may cause misdiagnosis!
To enter comment status:
z Press <Comment> to enter comment status. Or,
z Move cursor to where you want to add comments, and then press alphanumeric keys to
enter the corresponding characters and enter comment status.
To exit comment status:
In comment status,
z Press <Comment> to exit comment status. Or,
z Press <Exit> to exit comment status.
5.1.1 Adding Comments

Inputting comments with keyboard
1. Move cursor to the desired position.
2. Press the alphanumeric keys to enter comment status and insert corresponding
characters. Upper case letters are inserted by default.
h To input lower case letters, press <Caps Lock>;
h Press <Shift> and alphanumeric keys simultaneously to shift to opposite or input
symbols on the upper part of the button.
3. To end inputting comments,
h Move the cursor to confirm and end adding comments. The cursor turns to non-editing
status.
h Press <Enter> to confirm and end adding comments. The cursor turns to non-editing
status and start a new line.
h Press <Set> to confirm and end adding comments. The cursor turns to non-editing
status and start a new line.
h Press <Back> to cancel and delete the current comment.
Add comments from comments library (search word by the firs letter)
1. Move cursor to where you want to add comments.
2. Press alphanumeric keys to enter comment status and insert corresponding characters.
3. Rotate <Multifunctional Knob (R)>, the system searches the word begins with the inputted
letter and displays them circularly.
4. To end adding comments,
h Move cursor to cancel and end adding comments.
Annotating the Image 5-1

h Press <Enter> to add the selected comment and end adding comments. The cursor
turns to non-editing status and start a new line.
h Press <Set> to add the selected comment and end adding comments. The cursor
moves to the end of the comments.
Add comments from comments library (select word in the menu)
1. Move cursor to where you want to add comments. Press <Set> to set the initial position.
You can also move the comment later. If initial position is not set, the comments will be
added to behind the last editing position.
2. Press <Menu> to open the comment menu.
3. Select a comment in the menu and press <Set> to activate it and move it to the initial
position.
4. Move the comment with the track ball.
5. Press <Set> to confirm.
5.1.2 Adding Arrow

1. Move cursor to where you want to add arrow. You can also move the arrow later.
2. Press <Arrow> to add arrow. The cursor turns to a selected arrow.
3. The “Rotation” indicator of <Multifunctional Knob (R)> lights up. Rotate the
<Multifunctional Knob (R)> to change the direction of the arrow by 15 degrees.
4. Press <Set> to confirm and continue adding arrow or press <Back> to delete the last
arrow. Press <Arrow> to exit arrow mode.
5.1.3 Moving Comments/Arrows

1. Move cursor to the comment/arrow that you want to move, and the cursor changes to “ ”.
2. Press <Set> to select the comment/arrow and the cursor changes to the frame of the
comment/arrow.
3. Move the frame of the comment/arrow to a new position with the track ball.
5.1.4 Editing Comments

1. Move cursor to the comment to be edited, and press <Set> twice to enter comment editing
status.
2. Move cursor to the editing position with the direction buttons. Press <Del> to delete the
character on the right of the cursor, and press <Backspace> to delete the character on the left
of the cursor.
3. Press <Set> to confirm and exit or press <Back> to cancel and delete the current comment.
5.1.5 Deleting Comments/Arrows

1. Move cursor to the desired comment/arrow and the cursor turns to “ ”. Press <Set> to select
the comment/arrow.
2. Press <Back> or <Del> to delete the comment/arrow.
Press <Clear> to clear the screen.
5-2 Annotating the Image

5.2 Body Mark
Body mark indicates the posture of patients and orientation of transducer during ultrasonic exam. It
is an additional remark to the ultrasonic image.
5.2.1 Adding Body Mark

1. Press <Body Mark> to open the “BodyMark Lib” dialog box.
2. Move cursor to the desired body mark and press <Set> to add the body mark to the image.
3. Roll the track ball to move the transducer mark and rotate the <Multifunctional Knob (R)>
to rotate the transducer mark.
In dual B/quad B mode, you can add body mark into the two/four images respectively.
5.2.2 Moving the Body Mark

1. Move cursor to the body mark and the cursor turns to “ ”. Press <Set> to select the body
mark and the cursor turns to the frame of the body mark.
2. Move the frame of the body mark to the desired position with the track ball.
5.2.3 Editing the Body Mark

1. Move cursor to the transducer mark of the body mark and press <Set> twice. The cursor
turns to the transducer mark.
2. Roll the track ball to move the transducer mark and rotate the <Multifunctional Knob (R)>
to rotate the transducer mark.
3. Press <Set> to confirm and exit.
5.2.4 Deleting the Body Mark

To delete the body mark:
z Double-click <Body Mark> to delete the body mark of current window.
z Press <Clear> to clear all the body marks.
Annotating the Image 5-3

6 Auxiliary Functions
6.1 Biopsy Guide

For details about the probes, needle-guided brackets and biopsy guide, please refer to “8 Probes
and Biopsy”.
6.1.1 Basic Operations
WARNING: Do not freeze the image while performing biopsy.
To enter biopsy mode: Press <Menu> to open the B image menu, and then click [Biopsy] to
open the biopsy menu and enter biopsy mode. In M+B mode, you need to switch to B Img
Menu.
In the biopsy menu,
z [NGB Model (Model)]: If the brackets for current transducer are more than one, click this
item to switch brackets.
z [Guideline (All/A/B/C)]: To select the guide line to be displayed.
z [Display (On/Off)]: To display/hide the guide line.
z [Dot Size (Small/Medium/Large)]: To set the size of dots in the guide line.
z [Verify]: Click [Verify] to open the “Biopsy Verify” menu and verify the biopsy guide line.
6.1.2 Adjusting the Guide Line
WARNING: 1. Prior to each puncture, calibrate the needle guide line.

2. If the positions of the needle and needle guide line are not
consistent, do not execute needle guide operation.
NOTE: The B-Mode image must be live and active to verify the onscreen biopsy guideline.
In the “Biopsy” menu, click [Verify] to open the “Biopsy Verify” menu.
In the “Biopsy Verify” menu,
z [Guideline (All/A/B/C)]: To switch among guide lines.
z [Position (Value)]: Move the cursor to this item, and then press <Set> or <Back> to move
the guide line. It is available only when one guide line is displayed.
z [Angle (Value)]: Move the cursor to this item, and then press <Set> or <Back> to
rotate the guide line. It is available only when one guide line is displayed.
z [Save]: To save the direction and position of current guide line.
z [Load Factory]: To load factory configuration of current guide line.
z [Exit]: To return to the “Biopsy” menu and display the guide lines as just set.
Auxiliary Functions 6-1

6.2 Lithotrity
“Lithotrity” helps to locate the focus point of lithotrity wave during lithotrity treatment. By watching
the procedure of lithotrity in real-time and adjusting the intension and frequency of the lithotrity
wave, the harm to the patients can be reduced to the least.
To use “Lithotrity”, please enable “Lithotrity” first in “PresetÆSystem PresetÆImage Preset”.
To enter lithotrity mode: Press <Menu> to open the B Img Menu, and then click [Lithotrity] to
open the lithotrity menu and enter lithotrity mode. In M+B mode, you need to switch to B Img
Menu.
In “Lithotrity” menu:
z [Display (On/Off)]: To display or hide the lithotrity guide line.
z [Dot Size (Small/Middle/Large)]: To set the size of dots in the guide line.
z [Exit]: To exit “Lithotrity” menu.
In lithotrity mode:
z The lithotrity line is a vertical dotted line located in the middle of the screen, the position
and direction of which cannot be changed.
z The lithotrity mark is a “×” mark located on the lithotrity line which can be moved up and
down along the lithotrity line: Roll the track ball downwards to move the mark downwards,
and roll the track ball upwards to move the mark upwards.
z The depth of the mark is displayed in the lower, right corner of the screen.
6-2 Auxiliary Functions

7 File Management
7.1 Formats of Files

File formats adopted by the diagnostic system only:
z FRM: System-defined single-frame static file format, non-compressed format, used for
measurements and comments.
z CIN: System-defined multi-frame file format; you can perform manual or auto cine review,
and perform measurements or add comments to the reviewed images. After you open
stored a CIN file, the system automatically enters cine review status.
File formats that are compatible with personal computers:
z BMP: Single-frame file format, used to save the current screen, non-compressed format;
z JPG: Single-frame file format, used to save the current screen in the compressed format;
you can set the compression ratio.
z DICOM file (DCM): DICOM standard files format, single-frame or multi-frame format.
Available for systems with DICOM only.
z AVI: Multi-frame file format.
7.2 Saving Files

During an exam,
1. Press <Freeze> to freeze the image.
2. Press <Menu> to open the freeze menu.
3. In the Freeze Menu, move the cursor to [Save As…] and click a format in the sub menu to
save image or cine files to USB storage device.
Save a file quickly: During an exam, press <Save> to save the current screen to image file as
preset format.
7.3 File Management

To open the file manager
3. Click [File Manager] to open the file manager.
To create a directory:
1. Select a driver in the drives list.
2. To select the path:
h Double click a directory to enter.
h Double click “.." to return to the father directory.
3. Click [New], and a dialog pops up. Input the name of the new directory in the dialog box.
4. Click [OK] to confirm or click [Cancel] to cancel.
File Management 7-1

To delete a file/directory:
1. Select a driver.
2. Select the path.
3. Select the file/directory to be deleted and click [Delete].
4. Click [OK] to confirm deleting, or click [Cancel] to cancel.
To rename a file/directory:
1. Select a driver.
2. Select the path.
3. Select the file/directory to be renamed and click [Copy].
4. Input the new name of the file/directory.
To copy a file/directory:
1. Select the path of the source file/directory.
2. Select the file/directory to be copied and click [Copy].
3. Select the path of the destination file/directory.
4. Click [Paste].
5. If the file/directory to be pasted already exists, a dialog box pops up. Click [OK] to confirm
overwriting, or click [Cancel] to cancel copying.
7-2 File Management

7.4 iVision
iVision is used for presentation of images, in which images (including formats of ultrasonic system
and standard formats) are displayed one by one in the sequence of file name. The formats
supported by the system are: JPG, BMP, DCM single frame and FRM. The formats not supported
are: AVI and DCM multi frames.
To enter iVision
3. Click [iVision] to open iVision.
In the “iVision” dialog box

z [Browse]: To select the directory of presentation.
z [Demo Mode (Auto Play/Manual Play)]: To select the mode of playback.
z [Interval (time)]: To set the time interval of playback when “Auto Play” is selected. Click [a]
and [b] to change the time interval.
z [Start]: To start playback.
z [Exit]: To exit iVision.
Manual Playback
z If “Manual Play” is selected, press the directions <> and <> to play the images.
To exit iVision
z When reviewing CIN files, press <Freeze> to exit iVision.
z When reviewing files of other formats, click [Exit] to exit iVision.
z Press <Exit> to exit iVision.
File Management 7-3

8 Probes and Biopsy
8.1 Probes
NOTE: For details of storage time and condition for disinfected probes or sterilized probes and
brackets, please refer to Technical standard for Disinfection of Medical and Health
Structures.
The system supports the following probes:

No. Probe Model Type Illustration
1 35C20EA Convex
2 35C50EA Convex
3 65C15EA Convex
4 65EC10EA Convex
5 65EL60EA Linear
Probes and Biopsy 8-1

No. Probe Model Type Illustration
6 75L38EA Linear
7 75L53EA Linear
8 75L60EA Linear
9 75LT38EA Linear
Some of the probes have matched needle-guided brackets for biopsy, the available probes and the
corresponding needle-guided brackets are listed as follows:
Needle-
guided Biopsy
Probe Model Type Applicable Biopsy Needle
Bracket Angle/Depth
Model
Metal/needle
un- 13G, 15G, 16G, 18G, 20G
35C20EA NGB-003 11º, 23º detachable
Metal/needle
14G, 16G, 18G, 20G, 22G
detachable
Metal/needle
14G, 16G, 18G, 20G, 22G
detachable
35C50EA NGB-001 25º, 35º, 45º Metal/needle
un- 13G, 15G, 16G, 18G, 20G
detachable
Metal/needle
65C15EA NGB-005 12.7º, 24.2º un- 13G, 15G, 16G, 18G, 20G
detachable
Metal/needle
65EC10EA NGB-004 / un- 16G, 17G, 18G
detachable
8-2 Probes and Biopsy

Needle-
guided Biopsy
Probe Model Type Applicable Biopsy Needle
Bracket Angle/Depth
Model
Metal/needle
65EL60EA NGB-009 0º 13G, 15G, 16G, 18G, 20G
detachable
Metal/needle
75L38EA NGB-002 40º, 50º, 60º un- 13G, 15G, 16G, 18G, 20G
detachable
Metal/needle
14G, 16G, 18G, 20G, 22G
detachable
75L53EA NGB-007 40º, 50º, 60º
Plastic/needle
13G, 15G, 16G, 18G, 20G
detachable
Metal/needle
14G, 16G, 18G, 20G, 22G
detachable
75L60EA NGB-012 40º, 50º, 60º
Plastic/needle
13G, 15G, 16G, 18G, 20G
detachable
Metal/needle
75LT38EA NGB-010 30º, 40º, 50º 13G, 15G, 16G, 18G, 20G
detachable
8.1.1 Name and Function of Each Part of the Probe

The basic structures and corresponding functions of probes are basically the same; the following
will take probe 35C20EA as an example.
<1> <2>
<3>
<4>
<5>
No. Name Function

It converts the electrical signal into ultrasound signal, making
the sound beams focus in the given direction; meanwhile, it
<1> Probe head will receive the ultrasound signal and then convert the
received signal into electrical signal. The lens on the surface
is the acoustic lens. Apply ultrasound gel on the acoustic lens.
Needle-guided bracket fix
<2> Used to mount the needle-guided bracket.
tabs and grooves

No. Name Function
Used to transmit electrical signals between the probe body
<3> Probe cable
and connector.
Used to connect the probe to the ultrasonic diagnostic
<4> Probe connector
system.
Used to lock the connector to the ultrasonic diagnostic
<5> Lock handle
system.
Tips:
The probes’ structure marked <2> in the figure above may vary with the matched needle-guided
brackets.
65EL60EA：
<1> <2>
<3>
<4>
<5>
<6>
Name Function
No.
It utilizes the piezoelectric effect to convert electrical

signals into ultrasound waves, which are transmitted to the
body, and to generate electrical signals when receiving the
<1> Transducer head
reflected ultrasound waves (echoes).The lens on the
surface is the acoustic lens. Apply ultrasound gel on the
acoustic lens.
<2> Needle-guided bracket fix tab Mount the needle-guided bracket using this tab.
<3> Water injection/drainage port Used for inject/drain water
This transmits electrical signals between the transducer

<4> Cable
body and connector.
This connects the transducer to the ultrasonic diagnostic

<5> Connector
system.
This locks the connector to the ultrasonic diagnostic

<6> Lock handle
system.

8.1.2 Orientation of the Ultrasound Image and the Probe
Head
The orientation of the ultrasound image and the transducer are shown as below. The “Mark” side
of the ultrasound image on the monitor corresponds to the mark side of the transducer. Check the
orientation before the examination.
Method 1
The arrow on the ultrasound image is corresponding to the O mark on the transducer (taking
convex transducer as an example).
O Mark

Pointed to
marked side

Method 2
Mark
Orientation
Mark
8.1.3 Procedures for Operating

This section describes general procedures for operating the probe. The proper clinical technique to
be used for operating the probe should be selected on the basis of specialized training and clinical
experience.

Procedures for operating (with biopsy function):
Inspection before examination
Connection to the ultrasonic

diagnostic system
Examinations
Biopsy procedure
Disconnection to the ultrasonic

diagnostic system
Sterilization of the needle guided
bracket
Wiping off the ultrasound gel
Inspection after use

Washing the transducer with water
Storage
Draining/drying
Immersion into disinfectant
Removing the transducer from

disinfectant
Rinsing the transducer in sterile

water
Draining/drying
Storage

Procedures for operating (with no biopsy function):
Inspection before examination
Connection to the ultrasonic

diagnostic system
Examinations
Disconnection to the ultrasonic

diagnostic system
Wiping off the ultrasound gel
Washing the transducer with water
Draining/drying
Disinfection
Immersion into disinfectant
Removing the transducer from

disinfectant
Rinsing the transducer into sterile

water
Draining/drying
Storage
WARNING: Disinfect the probe and sterilize the needle-guided bracket before
and after an ultrasound-guided biopsy procedure is performed.
Failure to do so may cause the probe and the needle-guided bracket
become source of infection.

8.1.4 Wearing the Probe Sheath
A legally marketed probe sheath must be installed over the probe before performing intra-cavitary
and intra-operative examination. Protective barriers may be required to minimize disease
transmission. Probe sheaths are available for use with all clinical situations where infection is a
concern.
To order probe sheath, contact:
CIVCO Medical Instruments Co.
102 First Street South, Kalona, IA 52247-9589 USA Tel: 1-319-656-4447
E-mail: info@civco.com
http://www.civco.com
CAUTION: 1. Be sure to cover the probe with a new (unused) probe sheath to
prevent infection during examination. If the package of a probe
sheath is open or broken, the sterilization of the probe sheath may
not be sufficient. DO NOT use such a probe sheath.
2. The cover contains natural rubber latex and talc that can cause
allergic reactions in some individuals.
3. DO NOT use an expired probe sheath. Before using probe sheaths,
verify whether the term of validity has expired.
Method (for reference only):
1. Place an appropriate amount of gel inside 2. Insert the probe into the sheath, make
the sheath or on probe face. Poor imaging sure to use proper sterile technique. Pull
may result if no gel is used. cover tightly over probe face to remove
wrinkles and air bubbles, taking care to
avoid puncturing cover.
3. Secure the sheath with enclosed elastic 4. Inspect the sheath to ensure there are no
bands. holes or tears.

8.1.5 When the Immersion Method is Used (65EL60EA)
MINDRAY recommend a syringe: CIVCO 610-224
Please perform the following operations before using the syringe.

1． Open the syringe pack and take out the syringe.
2． See the following figure, take out the dustproof cap at the end of the syringe’s extension tube.
3． See the following figure, push back the locking nut and make the connector come out. The
connector will be connected to the transducer’s injection/drainage port.
Please refer to the following operations When the Immersion Method is used.
1． Put on the transducer cover.

For the procedures of putting
on the transducer sheath, refer
to subsection above. Check the
transducer sheath for wrinkles
and gaps.

2． Fill syringe with sterile water
and connect extension tube to
syringe, discharge all air in the
tube. Attach the syringe to
transducer fill port.
3． Orientate the transducer

downward and inject sterile
water up to the level a few cm
above the end of the transducer
surface.

4． Orientate the transducer
upward to discharge air in the
transducer cover.

5． Turn the valve of the syringe to
the position shown in the right
figure, and then push the
plunger of the syringe to
discharge the air.
6． Return the valve of the syringe

to the original position; orientate
the transducer downward to
discharge sterile water.

8.1.6 Probes Cleaning and Disinfection
After completing each examination, clean and disinfect (or sterilize) the probes as required. When
biopsy procedures have been performed, be sure to sterilize the needle-guided bracket. Fail to do
so may result in the probe and the needle-guided bracket to becoming sources of infection. Please
follow the instructions in the manual for cleaning.
Never immerse the probe connector into liquid such as water or
WARNING: disinfectant. Immersion may cause electrical shock or malfunction.
1. When performing cleaning and

CAUTION: disinfection of the probe to prevent
infection, wear sterile gloves.
2. After disinfection, rinse the probe thoroughly with sterile water

to remove all chemical residues. Chemical residues on the
probe may be harmful to the human body.
3 No cleaning and disinfecting may result in the probe becoming
a source of infection.
NOTE: 1. After the examination, wipe off the ultrasound gel thoroughly. Otherwise, the
ultrasound gel may solidify and degrade the image quality of the transducer.
2. DO NOT make the probe to become overheated (more than 55°C) during cleaning
and disinfections. High temperature may cause the probe to become deformed or
damaged.
Cleaning
Please refer to the instructions in the manual and follow your hospital policy and procedures for
cleaning.
1. Disconnect the probe from the system.
2. Wear sterile gloves to prevent infection.
3. Wash the transducer with clean water or soapy water to remove all the foreign matters, or,
wipe the transducer with a soft ethyl carbamate sponge. Avoid using a brush, because it may
damage the transducer.
4. Dry the transducer using a sterile cloth or gauze after rinsing. Do not dry the transducer by
heating it.
Disinfecting with Sprays
Use protective eyewear when disinfecting using sprays.

CAUTION:
2. After you have finished cleaning, spray the transducer with a disinfectant. Follow the
disinfectant manufacturer’s recommended contact time and mode.
3. Remove any residue with a water-moistened soft cloth on the transducer.
4. Wipe off water on the transducer using sterile cloth or gauze after washing.

Connector
Strain relief
NOTE: Observe the graph here carefully to perform disinfection. Do not spray the strain relief on
the connector end or the connector.
Disinfecting by Immersion
2. Clean the transducer before disinfecting it.MINDRAY recommends the following solutions to
disinfect the transducer.
z Refer to the instructions provided by the chemical manufacturer concerning concentration
of the disinfectant solution, method of disinfection and dilution and cautions during use.Do
not soak the transducer connector or the cable near it into water or any solution.
z Soak the transducer into the disinfectant solution for the shortest time the manufacturer
recommends (for example, the shortest time recommended by the manufacturer for
soaking Cidex OPA is 12 minutes).
z Follow local regulations when selecting and using the disinfectant.
3. Rinse the transducer with plenty of sterile water (about 2 gallons) for at least 1 minute to
remove all chemical residues on it.Or, follow the rinsing method recommended by the
disinfectant manufacturer to rinse the transducer.
4. Wipe off the water on the transducer with sterile cloth or gauze after rinsing it.Do not dry the
transducer by heating.

Strain relief
Probe handle
NOTE: 1. Observe the graph here carefully to immerse the transducer. Only soak parts of
the transducer below the strain relief.
Compatible Disinfectants
Manufacturer Trade Name Procedures Type

Pharmaceutical T-Spray II Please refer to the instructions provided Spray
Innovations, Inc. by the manufacturer of the solution for
details.
Parker PROTEXTM Please refer to the instructions provided Spray
Laboratories Inc. DISINFECTANT by the manufacturer of the solution for
SPRAY details.
Metrex MetriZyme Please refer to the instructions provided Solution
by the manufacturer of the solution for
details.
ASP Cidex Activated Please refer to the instructions provided Solution
Dialdehyde Solution by the manufacturer of the solution for
details.
Please refer to the instructions provided Solution
ASP Cidex OPA by the manufacturer of the solution for
details.
TrophonSonex-HL Please refer to the instructions provided Solution

Nanosonics (Used with Trophon by the manufacturer of the solution for
Limited EPR Ultrasound details.
Probe Disinfector)
Sterilization
For intra-operative probes, they have to be sterilized after completing each examination.
2. Clean the probe before sterilizing it. MINDRAY recommends the following solutions to sterilize
the probe.
Hydrogen Peroxide and Peroxyacetic Acid -based sterilization solution

Trade Name Chemical Name Procedures
®
Minncare Cold 22% Hydrogen Peroxide Dilute the sterilant with sterilized purified water
Sterilant 4.5% Peroxyacetic Acid (1:20).
Immersed time: 11 hours.
Temperature: 20℃-25℃.
Please refer to the instructions provided by the
manufacturer of the solution for details.
Before safety and performance is affected, probe 75LT38EA can be sterilized by Minncare COLD
STERILANT for at least 135 times (11 hours for one time).
Glutaraldehyde-based sterilization solution

Trade Name Chemical Name Procedures
Soak the transducer into the activated solution
Cidex Activated for 10 hours (20-25℃)
2.4% Glutaraldehyde
Dialdehyde Solution Please refer to the instructions provided by the
manufacturer of the solution for details.
Before safety and performance is affected, probe 75LT38EA can be sterilized by Cidex Activated
Glutaraldehyde Solution for at least 217 times (10 hours for one time).
z Refer to the instructions provided by the chemical manufacturer concerning concentration of
the sterilization solution, method of sterilization and dilution and cautions during use.
z Do not soak the probe connector or the cable near it into water or any solution.
z Follow local regulations when selecting and using the sterilization solution.
3. Rinse the probe with plenty of sterile water (about 2 gallons) for at least 1 minute to remove all
chemical residues on it. Or, follow the rinsing method recommended by the sterilization
solution manufacturer to rinse the probe.
4. Wipe off the water on the probe with sterile cloth or gauze after rinsing it. Do not dry the probe
by heating.
Immerse the 75LT38EA probe in the solution

NOTE: Repeated disinfection may degrade the performance and safety of the probe.
8.1.7 Storage and Transportation

When all examinations for the day have been completed, confirm that the probe is in good
condition. After disinfecting the probe, confirm that the probe is in good condition and store it in a
suitable place so that the next examination can be conducted smoothly.
1. To prevent the probe from being damaged, DO NOT store it in locations where it may be
exposed to:

z Direct sunlight or X-rays
z Sudden changes in temperature
z Dust
z Excessive vibration
z Heat generators
2. Store and transport the probe under the specified ambient conditions.
3. When the probe is sent to MINDRAY Customer Service Department or sales representative for
repair, be sure to disinfect it and keep it in the carrying case to prevent infection.
4. Sterilize the carrying case as necessary.

8.2 Biopsy Guide
WARNING: 1. The person performing biopsy procedures must understand
diagnostic ultrasound thoroughly and have been trained
adequately, otherwise, side effects may be caused to the patient.
2. In situations listed below, the biopsy needle may fail to penetrate
the target. The incorrect biopsy may cause various side effects in
the patient.
z Use a needle-guided bracket other than that provided.
z Mount the needle-guided bracket incorrectly.
z Use a biopsy needle that is unsuitable for the type of biopsy
being performed.
z Use a biopsy needle that is unsuitable for the needle guide.
3. Before and after a biopsy procedure is performed, confirm that the
needle-guided bracket is normal. Manually confirm that the parts of
the needle-guided bracket do not slip off or move from their proper
positions. If the needle-guided bracket is used when parts are not
securely and correctly installed, the patient may be injured. If an
abnormality is found on the needle-guided bracket, immediately
stop using it and contact MINDRAY Customer Service Department
or sales representative.
4. DO NOT use a needle-guided bracket when scanning is performed.
The needle may advance in an incorrect direction and possibly
injure the patient.
Never perform a biopsy during image scanning.
5. DO NOT freeze an image while performing biopsy procedure.
6. During biopsy procedures, the needle may deviate from the desired
course due to the tissue characteristics or the type of needle. In
particular, needles of small diameters may deviate to a greater
degree.
7. Sterilize the probe and the needle-guided bracket before and after
each ultrasound-guided biopsy procedure is performed. Fail to do
so may cause the probe and the needle-guided bracket become
sources of infection.
8. The needle mark displayed on the ultrasound image does not
indicate the actual position of the biopsy needle. Therefore, it
should only be used as a reference. Always monitor the relative
positions of the biopsy needle during the procedures.
9. Adjust the needle mark before the biopsy procedure is performed.
10. When performing biopsy procedures, use only sterile ultrasound

gel that is certified to be safe. And manage the ultrasound gel
properly to ensure that it does not become a source of infection.
11. When performing the operation concerning biopsy, wear sterile
gloves.
12. Image of the biopsy target and the actual position of the biopsy
needle:
Diagnostic ultrasound systems produce tomographic plane

images with information of a certain thickness in the thickness
direction of the probe. (That is to say, the information shown in the
images consist all the information scanned in the thickness
direction of the probe.) So, even though the biopsy needle appears
to have penetrated the target object in the image, it may not
actually have done so. When the target for biopsy is small,
dispersion of the ultrasound beam may lead to image deviate from
the actual position. Pay attention to this.
If the target object and the biopsy needle appear in the image as
shown in the figures below (For reference only):
1. Biopsy 2. Target
The biopsy needle appears to reach the target object in the image
3
1
4
1. Target 2. Transducer 3. Needle 4. Ultrasound beam

Dispersion of the ultrasound beam
The biopsy needle may not have actually entered the target object
even though it appears to have done so on the image. To avoid
this problem, note points below:
z Do not rely only on the needle tip on the image. Pay careful
attention to that, when the biopsy needle comes into the target
object or contacts with it, the object should shift slightly.
z Before you perform the biopsy, please evaluate the size of the
object and confirm if the biopsy can be carried out.

8.2.1 Needle-guided Brackets
A needle-guided bracket is available for purchase as an optional accessory; it is used in
combination with the probe. Some of the probes have matched needle-guided bracket and needles.
To order needle-guided brackets, contact MINDRAY Customer Service Department or sales
representative.
For biopsy or treatment, ultrasound-guided biopsy procedures can be performed using the probe in
combination with a needle-guided bracket (optional accessory) and a biopsy needle (provided by
the user).
Names of Parts
This section describes the parts and corresponding functions of each needle-guided bracket. Here,
we take a matched probe as an example.
NGB-001, NGB-002, NGB-003, and NGB-005 (Metal/needle un-detachable)
The structure of plastic needle-guided bracket NGB-001, NGB-002, NGB-003 and NGB-005
are similar to each other. The following figure shows the structure with NGB-001 as an
example.
1 4
6
7
3
1. Locating pit 2. Clamp 3. Locating groove 4. Needle guide and the hole
5. Clamping knob of the needle guide 6. Needle guide rack 7. Grip knob
1. Needle-guided bracket 2. Transducer

NGB-001 (Metal/needle detachable)
Guiding hole
Groove V-shaped guiding block
Lock pin
Needle type adjusting base Needle fixing nut

Needle type dial scale
V-shaped cover
Clamp
Angle block
Angle adjusting base Angle pinch
Angle shift sign Pinch nut
No. Name Description

Clamp of needle-
<1> Used for installing the needle-guided bracket on the transducer
guided bracket
Groove of the needle-
<2> Matches with the tab of the transducer
guided bracket
<3> Angle adjusting base There are 3 types of angles available to be adjusted
Angle shift sign(11°,
<4> Matched with the biopsy angle(11°, 23°）
23°）
<5> Angle pinch nut Used for fixing the angle lock at a chosen angle
Used for determining the angle of the biopsy; different
<6> Angle block
specifications of blocks can be used
Used for installing biopsy needle; there are five specifications
<7> Guiding block
of guiding blocks for different biopsy needles

Specification of
<8> Matched with the corresponding biopsy needle(14G）
guiding block(14G）
<9> Needle guide hole Used for installing the biopsy needle
Pinch nut of needle-
<10> Used for locking the needle-guided bracket and the transducer
guided bracket
NGB-004 (Metal/needle un-detachable)
2 3
4
5
6
1. Locating bulge 2. Needle guide 3. Locking nut
4. Retaining clamp 5. Transducer 6. Locating groove

NGB-007
Metal / needle detachable needle-guided bracket:

Support of needle-
<1> Used for installing the needle-guided bracket on the transducer
guided bracket
Groove and tab of the Respectively matched with the tab and groove of the
<2>
needle-guided bracket transducer
<3> Angle adjusting base There are 3 types of angles available to be adjusted
Angle shift
<4> Matched with the biopsy angle(40°,50°,60°)
sign(40°,50°,60°)
<5> Angle pinch nut Used for fixing the angle lock at a chosen angle

<6> Angle block
<7> Guiding block
Specification of
<8> Matched with the corresponding biopsy needle(14G)
guiding block(14G)
<9> Needle guide hole Used for installing the biopsy needle
Pinch nut of needle- Used for locking the
<10>
guided bracket needle-guided bracket and the transducer
Plastic /needle detachable needle-guided bracket:

Support of needle-
<1> Used for installing the needle-guided bracket on the probe.
guided bracket
Used for determining the angle of the biopsy; there are three
<2> Angle block
specifications of blocks of angle.
Used for installing biopsy needle; there are five specifications of
<3> Guiding block
guiding blocks for different biopsy needles.
Groove and tab of the
<4> Respectively matches with the tab and groove of the probe.
needle-guided bracket
Specification of
<5> Matched with the corresponding biopsy needle (13G).
guiding block (13G)
Guiding hole of the
<6> Used for installing the biopsy needle.
biopsy needle
Specification of angle
<7> The corresponding biopsy angle is 60°.
block (60°)

2 6
7 9
3
10
8
4 11

Hole for installing
1 Used for installing the knob of fixing needle-guided bracket
guiding block
2 Groove Match with the tab on the transducer
Support of needle-
3 Used for installing the needle-guided bracket on the transducer
guided bracket
Knob of fixing needle-
4 Used for fixing the needle-guided bracket on the transducer
guided bracket
Needle distance Indicate distance between needle and the transducer head
5
scales surface
Guiding block Used for installing biopsy needle; there are five specifications
6
of guiding blocks for different needles
Knob of fixing the Used for fixing the needle
7
needle
Guiding hole of the Used for installing the biopsy needle
8
needle
Specification of
9 Matched with the corresponding biopsy needle
guiding block
Mark of indicating
10 Indicating needle distance scales
scales
Knob of fixing the
11 Used for fixing the guiding block
guiding block

1 5
2 6
3 8

1 Guiding block
Guiding hole of the
2 Used for installing the biopsy needle
biopsy needle
Support of needle-
guided bracket
Knob of fixing needle-
4 Used for fixing the needle-guided bracket on the transducer
guided bracket
Specification of
5 Matched with the corresponding biopsy needle (13G)
guiding block (13G)
Knob of fixing the
6 Used for fixing the guiding block
guiding block
7 Needle guide angle The needle guide angle of this needle-guided bracket
Grooves of the
8 Matched with the tabs of the transducer
needle-guided bracket
NGB-012
Metal/needle detachable needle-guided bracket:

Support of needle-
guided bracket
Groove and tab of Respectively matched with the tab and groove of the
2
3 Angle adjusting base There are 3 types of angles available to be adjusted
Angle shift
4 Matched with the biopsy angle (40°,50°,60°)
sign(40°,50°,60°)
5 Angle pinch nut Used for fixing the angle lock at a certain angle
6 Angle block
7 Guiding block
Specification of
guiding block (14G)
9 Needle guide hole Used for installing the biopsy needle
Pinch nut of needle- Used for locking the
10
guided bracket needle-guided bracket and the transducer
Plastic/needle detachable needle-guided bracket:
4
1 6
2 7

1 Guiding block
Used for determining the angle of the biopsy; there are three
2 Angle block
specifications of blocks of angle
Support of needle-
guided bracket
Specification of
guiding block (13G)
Groove and tab of the Respectively matched with the tab and groove of the
5
6 Needle guide hole Used for installing the biopsy needle
Specification of angle
7 Corresponding to the size of the biopsy angle (60°)
block (60°)
8.2.2 Basic Procedures for Biopsy Guiding

1. Select the right needle-guided bracket and needle, install them properly. For details, please
refer to “8.2.3 Needle-guided Bracket Inspection and Installation”.
2. Verify the biopsy guide line. For details, please refer to “8.2.4 Verifying the Biopsy Guide Line”.
3. Move the cursor onto the image menu, navigate the cursor to [Other] item and press <Set>.
Select [Biopsy] in the Other menu to enter the biopsy. Before biopsy guiding, you can preset
bracket model, biopsy display and guide line dot type.
Tip:
z If the current probe has no matched bracket; or, the image is frozen and the guide line is
hidden before image frozen, then you can’t enter Biopsy menu.
z Before entering Biopsy menu, the system will prompt you “Please verify guidelines before
biopsy”.
4. Set [Display] as “On” to display the guide line, select the bracket and guide line according to
actual situation. For details, please refer to “8.2.4 Verifying the Biopsy Guide Line”.
5. On the Biopsy menu, click [Verify] to enter the Verify menu to verify the guide line. For details,
please refer to “8.2.4 Verifying the Biopsy Guide Line”. After the verification, click [Save] on the
menu to save the parameter setting. And then click [Exit] to return to Biopsy menu.
Tip:
z If you switched the probe or needle-guided bracket during the biopsy, please verify the
guide line again.
z When exit the Verify menu without saving the setting, system will confirm with you “Data
have changes. Do you want to save the changes?”. Click [OK] to save the setting and
return to Biopsy menu.
6. Scan to locate the target. Center the target in the electronic guidezone path.
7. Direct the needle into the area of interest for specimen.
8. After extraction of the biopsy sample is completed, gently remove the probe from the body.
To exit Biopsy menu: press <Esc> key; or, navigate the cursor onto the other menu.
9. Disassemble the items and properly dispose of these items as required.

DANGER Fail to match the guidezone displayed to the guide may cause the
needle to track a path outside the zone.
It is extremely important that when using the adjustable angle biopsy
guides, the angle displayed on the screen matches the angle set on the
guide, otherwise the needle will not follow the displayed guidezone
which could result in repeated biopsies or patient injury.
8.2.3 Needle-guided Bracket Inspection and Installation
8.2.3.1 Inspection of the Needle-guided Bracket

Be sure to perform inspections before and after use of the needle-guided bracket. If an abnormality
is found on the needle-guided bracket, immediately stop using it and contact MINDRAY Customer
Service Department or sales representative.
1. Sterilize the needle-guided bracket before and after use.
2. Confirm that the needle-guided bracket is free of damage, deformation, stripping, malfunction,
loose, or missing parts.
3. Confirm that the needle-guided bracket is securely mounted in the correct position.
8.2.3.2 Installing the Needle-guided Bracket

NGB-001 metal/needle detachable needle-guided bracket
1. Put on the sterile transducer sheath.
2. Hold the transducer by one hand, select the proper needle-guided bracket, and hold it with the
other hand. Match the groove of the bracket with the tab of the transducer. Amount the bracket
onto the transducer.
3. Screw the pinch nut of the needle-guided bracket to confirm that the needle-guided bracket is
properly installed on the transducer.
4. Adjust the dial scale to the required needle type shift, and then screw the needle fixing nut to
lock the dial scale.(To adjust the dial scale you have to loose the needle fixing nut first.)
5. Pull the lock pin and close the V-shaped cover to fix the lock pin in the groove of the needle
type adjusting base, so as to install the needle into the guiding hole.

(1) Put on the transducer cover.
(2) Select a proper needle-guided bracket, and match the groove with the tab of the
transducer respectively. Mount the bracket onto the transducer.
(3) Screw the pinch nut of the needle-guided bracket to confirm that the needle-guided
bracket is properly installed on the transducer.
(4) Select a proper guiding block and push it into the groove above the angle block.
(5) Screw the nut of the block to secure the block.

(6) Insert a biopsy needle with the same specification as that of the guiding block into the hole
of the guiding block.
NGB-001, NGB-002, NGB-003 and NGB-005 metal/needle un-detachable needle-guided

bracket (taking NGB-001 as example)
(1) Inosculate the locating groove on the clamp with the two raised edges on the transducer
head and aligning the locating pit of the clamp to the convex point on the transducer head.
(2) Turn the grip knob at the tail of the needle-guided bracket tightly.
NGB-004 metal/needle un-detachable needle-guided bracket
(1) Put on the sterile probe sheath.

(2) Open the retaining clamp, align the needle-guided bracket with the probe to locate the
locating bulge on the needle guide to the locating grooves on the probe, and then turn the
retaining clamp to match it with the probe (see the figure below).
(3) When the retaining clamp is turned to the right position, the locking nut will lock the
retaining clamp and the needle-guided bracket is then mounted to the right position.
NGB-007 and NGB-012 (taking NGB-007 as example)

(1) Put on the sterile transducer sheath.
(2) Hold the transducer by one hand, select the proper needle-guided bracket, and hold it with
the other hand. Match the groove and tab with the tab and groove of the transducer
respectively. Amount the bracket onto the transducer.
(3) Screw the pinch nut of the needle-guided bracket to confirm that the needle-guided
bracket is properly installed on the transducer.
(4) Select a proper guiding block and push it into the groove above the angle block, and
clamp it tightly.
(5) Screw the nut of the block to secure the block.


(1) Put on the sterile probe sheath.
(2) Hold the probe by one hand, select the proper needle-guided bracket, and hold it with the
other hand. Align the narrow end tab of the needle-guided bracket with the groove of the
probe, then push the needle-guided bracket forward, making the tabs and the grooves of
the needle-guided bracket to match with the grooves and tabs of the probe.
(3) Check manually to confirm that the needle-guided bracket is securely installed on the
probe.
(4) Select a proper guiding block and push it into the groove above the angle block, and
clamp it tightly.


(2) Cover the support of needle-guided bracket on the transducer, making the groove of the
needle-guided bracket to match with the tab of the transducer. Set the needle-guided
bracket at the desired position, turn tightly the knob of fixing needle-guided bracket to fix
the needle-guided bracket.
(3) Select a proper guiding block and thread the knob of fixing the guiding block through the
hole of installing guiding block, move the guiding block to the desired position, then turn
tightly the knob of fixing the guiding block to fix the guiding block on the support of needle-
guided bracket.
of the guiding block and turn tightly the knob of fixing the needle.

(2) Hold the transducer by one hand, select proper needle-guided bracket, and hold it with the
other hand, and align the grooves of the needle-guided bracket with the tabs of the
transducer, then push the needle-guided bracket forward, making the grooves of the
needle-guided bracket to match with the tabs of the transducer. Set the needle-guided
bracket at the desired position, turn tightly the knob of fixing needle-guided bracket to fix
the needle-guided bracket.

(3) Check manually to confirm the needle-guided bracket is securely installed on the
transducer.
(4) Select a proper guiding block and push it into the groove above the support of needle-
guided bracket, then turn tightly the knob of fixing the guiding block to fix the guiding block
on the support of needle-guided bracket.
CAUTION: Ensure that all guide parts are seated properly prior to performing a
biopsy.
8.2.4 Verifying the Biopsy Guide Line

Adjusting the needle mark is necessary before every biopsy procedure.
1. Confirm that the needle-guided bracket has been installed securely in the correct position.
2. Prepare a container filled with sterile water.
3. Place the head of the probe in the sterile water, and get a biopsy needle into the needle guide.
4. When the biopsy needle appears on the image, confirm that the biopsy needle is displayed at
almost the same position as the selected needle mark.
WARNING: 1. Prior to each biopsy procedure, be sure to verify the guide line.

2. If the needle is not consistent with the guide line, DO NOT perform
the biopsy procedure.
NOTE: You can perform guide line verification on a single live B/C image, and all biopsy-
irrelevant operations are forbidden.
8.2.5 Removing the Needle-guided Bracket

NGB-001
1. Pull the lock pin and open up the V-shaped cover to expose the needle.
2. Separate the bracket and the transducer from the needle.

3. Screw the pinch nut to release the needle-guided bracket.
4. Separate the bracket and the transducer.
Plastic needle-guided bracket:

While holding the transducer and the needle-guided bracket, open the Grip knob of the
needle-guided bracket.
NGB-002 metal/needle un-detachable needle-guided bracket:
NGB-003
(1) Screw the nut of the guiding block and remove the guiding block slightly along the
direction of the needle’s tail.

(2) Separate the residual part of the needle-guide bracket and the transducer from the needle.
(3) Screw the pinch nut of the bracket, and remove the needle-guided bracket from the
transducer.
Metal/needle un-detachable needle-guided bracket:
NGB-004 metal/needle un-detachable needle-guided bracket:
Hold the probe in the left hand, unscrew the locking nut with the right hand to open the
retaining clamp, and then raise the needle-guided bracket to separate the locating bulge from
the locating grooves.
NGB-005 metal/needle un-detachable needle-guided bracket
Hold the probe and the needle-guided bracket, open the grip knob of the needle-guided
bracket.
NGB-007
transducer.

(1) Remove the guiding block slightly along the direction of the needle’s tail.
(2) Separate the residual part of the needle-guide bracket and the probe from the needle.
(3) Remove the support of needle-guided bracket from the probe.
(1) Turn on the knob of fixing the needle and separate the needle from the needle-guided
bracket.
(2) Turn on the knob of fixing guiding block and remove the guiding block from the hole of
installing guiding block.
(3) Turn on the knob of fixing needle-guided bracket and remove the needle-guided bracket.
(1) Remove the guiding block slightly along the direction of the needle’s tail, and separate the
residual part of the needle-guide bracket and the transducer from the needle.
(2) Remove the support of needle-guided bracket from the transducer.
NGB-012
transducer.
Plastic needle-guided bracket:

(1) Remove the guiding block slightly along the direction of the needle’s tail.

(3) Remove the support of needle-guided bracket from the transducer.
8.2.6 Clean and Sterilize the Needle-guided Bracket

Cleaning
Please follow the instructions in the manual for cleaning.
2. Wash the needle-guided bracket with water or soap water to remove all the external matters.
Or, clean the needle-guided bracket with urethane sponge.
3. Wipe off the water on the needle-guided bracket using sterile cloth or gauze after washing it.
Sterilization
2. Clean the needle-guided bracket before sterilizing it. MINDRAY recommends the following
solution or sterilizing system to sterilize the needle-guided bracket.
3. Follow local regulations when selecting and using the disinfectant.
Glutaraldehyde-based sterilant:
Chemical name Trade name Procedures
Cidex Please refer to the instructions provided by the
Glutaraldehyde Activated manufacturer of the solution for details.
(2.4%) Dialdehyde Soak the transducer into the activated solution for 10
Solution hours (20-25℃)
Before safety and performance is affected, plastic bracket NGB-012 can be sterilized by Cidex
Activated Glutaraldehyde Solution for at least 233 times (10 hours for one time).
z Refer to the instructions provided by the chemical manufacturer concerning concentration
of the solution, and method of disinfections and dilution. Note that the glutaraldehyde
disinfectant solution needs an activating solution.
z Rinse the needle-guided bracket thoroughly with sterile water to remove all chemical
residues on it.
z Wipe off the water on the needle-guided bracket with sterile cloth or gauze after rinsing it.
STERRAD 100S low-temperature hydrogen peroxide gas plasma sterilization system
Chemical name Trade name Procedures
Hydrogen
Hydrogen Please refer to the instructions provided by the producer of
peroxide gas
peroxide vapor the solution for details.
plasma
z Refer to the instruction of STERRAD 100S sterilizing system provided by the
manufacturer for operation instructions and cautions.
z The STERRAD 100S low-temperature hydrogen peroxide gas plasma sterilization system
is available for metal needle-guided brackets.
High-pressure steam sterilization (only applicable for metal guided-bracket)
Autoclaving (moist heat) 121° C for 20 minutes.
NOTE: 1. Repeated sterilization may degrade the safety and performance of the needle-guided
bracket.

2. The high-pressure steam/ immersion sterilization do not affect the bracket duration
life, and the duration life is affected by the daily application of the bracket. Please
check the appearance of the bracket before using.
8.2.7 Storage and Transportation

1. Don’t use the carrying case for storing the needle-guided bracket. If the carrying case is used
for storage, it may become a source of infection.
2. Between examinations, keep the needle-guided bracket in a sterile environment.
3. When the needle-guided bracket is sent to your MINDRAY representative for repair, be sure to
disinfect or sterilize it and keep it in the carrying case to prevent infection.
4. Sterilize the carrying case as necessary.
5. Store or transport the needle-guided bracket under the following ambient conditions:
z Ambient temperature: -20°C to 55°C
z Relative humidity: 30% to 85% (no condensation)
8.2.8 Disposal
Be sure to dispose the needle-guided bracket only after sterilizing it.
Contact your MINDRAY representative when disposing of this device.

9 Preset
This chapter introduces how to customize your ultrasonic diagnostic imaging system.
The preset function is designed to configure the parameters of operating the system and maintain
user workflow preferences.
To enter preset: Press <Setup> to open the preset menu.
To exit preset: Click [Return] in the preset menu to close the preset menu and exit preset.
CAUTION: When the setup data is changed, be sure to save the preferences
according to the methods described in this chapter. Mindray is not
responsible for the loss of the setup data.
Note: 1. The Preset parameters take effect only after returning from Preset following the
above operations.
2. Entering and returning from Preset during an exam will clear the measurement
data.
The following table describes the contents of the items in the preset menu.
Items Contents or Functions
System Preset Region, General, Image Preset, Meas Param, OB, Key Config and Option.
Exam Preset To select exam preset or configure exam preset.
Image Config To configure the default image parameters of each exam mode.
Measure Preset To configure the measure packages.
Comment Preset To configure the comment library for different exam modes.
To configure parameters related to DICOM applications. This item is only
DICOM
available for systems configured with DICOM software.
Manage Settings To manage the preset data.
Maintenance To maintain the system.
About Click to check the system information.
Return Save changes and exit preset.
Preset 9-1
The basic operations of controls in Preset are as follows:
Text box: Input text with the keyboard.
Radio Button: Click the button to select an item. At least one and only can be selected.
Check box: Click the check box to select it or deselect it. Selecting plural boxes and
selecting none are both allowed.
Drop-down list: Click the arrow beside the list to select an item.
9.2 System Preset

System Preset contains the following sub items:
Item Descriptions
To configure the name of hospital, language, time zone, date and
Region
time, etc.
To configure the contents displayed in the patient information area,
General
system dormancy, file saving and comments, etc.
To configure the default image parameters when system is reset and
Image Preset
image control, etc.
To configure the measure ruler, measure result, exam report and
Meas Param
units of measure results, etc.
To configure the formula for Fetal Gestational Age, Fetal Growth and
OB
Fetal Weight, etc. Refer to [Advanced Volume] for details.
To configure the function of some buttons in control panel and
Key Config
parameters related to the control panel.
Peripheral To configure parameters related to peripherals.
Option To configure the options.
9.2.1 Region
Item Type Description
Hospital Text box Input the name of hospital here.
Language Drop-down list To select the language of system.
Time Zone Drop-down list To select the time zone.
Time Format Radio button To select the format of time.
Date Format Radio button To select the format of date.
System Date Number Move the cursor to the corresponding field,
and then press <Set> to increase the value or
System Time Number press <Back> to decrease the value.
9-2 Preset
9.2.2 General
Sub-page Item Type Description
Info displays in To select the items to be displayed in the
Check box
image banner patient information area.
Patient
H&W Unit Radio button To select the unit: Metric/English.
Info
To select the formula of surface area:
Surface Formula Radio button
Orient/West.
To select the compression ratio of JPG
JPG Compress Drop-down list
format: Low/Middle/High.
To select the format of single-frame files:
Single Frame
Image Drop-down list FRM/JPG/BMP/DCM (DCM is available only
Format
Format when DICOM is installed).
To select the format of multi-frame files:
Multi Frame Format Drop-down list CIN/AVI/DCM (DCM is available only when
DICOM is installed).
Switch of dormancy Check box To turn On/Off dormancy.
System This item can be configured after dormancy is

Dormancy turn on. Click “▲” to increase the value and
Wait Time Number
click “▼” to decrease the value. The range is:
5-60 minutes and the step length is 1 minute.
To set the size of comments:
Font Size Radio button
ABC Small/Middle/Big.
Arrow Size Radio button To set the size of arrows: Small/Middle/Big.
To select the format of video output:
Video export format Radio button
PAL/NTSC.
Video To set the paper size of graph/text printer: A4,
Paper Size Drop-down list
export B5, Letter, Unknown.
format
Local print/ Ultrapartner Print. Click [>>] to
Print Type Drop-down list preset the Current Printer Server if
“Ultrapartner Print” is selected.
Reset all parameters to factory default in this
/ Load Factory Button
page.
9.2.3 Image Preset

To set the model of default transducer
Probe Drop-down list
Reset displayed when no transducer is connected.
Config To set the default exam mode after system
Exam Mode Drop-down list
starts.
Preset 9-3
To set whether to adopt the default image
parameters or not when beginning a new
Reload Preset on
Check box exam: Checked (to adopt default image
New Patient
parameters)/Unchecked (to continue with
current image parameters)
To set the status when frozen in measurement
Frozen when
Radio button mode: Cine (to switch to cine review
Measurement
mode)/Measure (to keep measuring)
Checked (enables lithotrity)/Unchecked
Lithotrity Enable Check box
(disables lithotrity)
Checked (enables image
Image Merge Check box merging)/Unchecked (disables image
Image merging)
Control To set the arrangement of B/M images in B+M
B/M Display Mode Radio button
mode: Up/Down, Left/Right.
Checked (to display thumbnail when
Display Thumbnail
Check box zooming)/Unchecked (to hide thumbnail when
when Zoom
zooming)
Reset all parameters in this page to factory
/ Load Factory Button
default.
9.2.4 Meas Param

To select the cursor type: Symbol (marks
Cursor Type Drop-down list different calipers with symbols), Number
(marks different calipers with numbers).
To select the size of mark: Large, Middle and
Mark Size Drop-down list
Small.
To set the number of cardiac cycles in HR
measurement (the number of cardiac cycles
Measure Heart Beat Drop-down list
selected when measuring should match the
Ruler
preset number here): 1~8.
To set whether to display the dotted line
Cursor Line Display Check box between ends of calipers or not when
measuring: On/Off.
To set whether to display the dotted lines
Ellipse Cross Line
Check box indicating the major axis and minor axis or not
Display
in ellipse measurement: On/Off.
To set the background color of the result
Result Background Drop-down list
window: Transparent, Grey.
Measure To set the contents displayed in result
Result Show Drop-down list
Result window: All, Current.
To set whether to display SD (standard
SD Display Check box
deviation) in the result window.
9-4 Preset
To set whether to display EDD (Estimated
EDD Display Check box
Delivery Date) in the result window.
Results are cleared To set whether to clear the measurement
Check box
if deleting caliper results when deleting the calipers.
Exam To set the format of growth graphs: 1*1, 2*1
Trend Format Drop-down list
Report and 2*2.
Distance, Area,
Volume, Time,
Unit Drop-down list To select the unit of the results
Velocity, Slope,
Acceleration
9.2.5 OB
To configure the formulas of Fetal Gestational Age, Fetal Growth and Fetal Weight. Refer to
[Advanced Volume] for details.
9.2.6 Key Config

To define the functions of some keys in control panel or buttons of the footswitch and parameters
of control panel.
1. Select a page in “Key”, and then select the key to be configured in the list.
2. Select a page in “Function”, and then click a function to assign it to the selected key.
Panel Panel Function Available Functions
Analog B/W Video Print
Standard Print (to print graph/text)
Save Single frame Image to Local Disk
Output
Save Single frame Image to USB Disk
Save Multi-frame Image to Local Disk
Save Multi-frame Image USB Disk
Print, Save, Exam Mode To switch to the corresponding exam mode.

F1, F2, F3, Trend Dlg: Open the “Obstetric Growth Curve”
F4, F5; dialog box.
Gain, SD: Displays/hides SD of Obstetric.
A.Power Set Home: Sets current location as home in
Key
(the function comment mode.
Application
when Gain Home: Moves cursor to home in comment mode.
and A.Power Report: Opens/closes report.
is pressed)
iVision: Opens iVision.
iStation: Opens/closes iStation.
Biopsy Line Display, M-Mark Display, Rotation, 4B,
Clear,
Other Exit: Closes the dialog box without saving
changes.
TSI, None
Footswitch Left, Right Output Same as those of “Panel”.
Preset 9-5
Panel Panel Function Available Functions
Exam Mode Same as those of “Panel”.
Application Same as those of “Panel”.
Biopsy Line Display, M-Mark Display, Rotation, 4B,
Other Clear, Exit, TSI, B, M, Dual, Freeze, Measure,
Comment, Body Mark, Menu, Exam, None
Keyboard preset:
To set the brightness of keyboard back light:
Key Lightness Drop-down list
Low/High/None
To set the volume of keyboard sound:
Key Volume Drop-down list
Low/High/None
To set the speed of cursor when rolling the track
Trackball Speed Drop-down list
ball: Slow/Mean/Fast
Preset of Key Config

Key
z Print Analog B/W Video Print
z Save Save Single frame Image to Local Disk
z F1 Save Single frame Image to USB Disk
z F2 Report
Footswitch
z Left Analog B/W Video Print
z Right Freeze
9.2.7 Option
Select an option in the list, click [Install] to install it or click [Uninstall] to un install it.
9.3 Exam Preset

To configure the related parameters of each exam mode.
9.3.1 Exam Selection

“Exam Selection” is used to select available exam modes for a transducer.
1. Select the model of transducer in the “Probe” drop-down list.
2. To select exam modes for the transducer:
z [>]: Select an exam mode in “Exam Library”, and click [>] to add it to “Exam Selected”;
z [>>]: Click [>>] to add all exam modes in the “Exam Library” to “Exam Selected”;
z [<]: Select an exam mode in “Exam Selected”, and click [<] to delete it;
z Sort: Select an exam mode in “Exam Selected”, and click [Move Up] or [Move Down] to
move it up and down. The sequence here is the same as that in the “Exam Mode” menu.
9-6 Preset
9.3.2 Exam Config
To select the applied part of exam modes: Click the cell corresponding to “Application” of each
exam mode and select the applied part in the drop-down list.
To copy parameters of an exam mode to another exam mode
1. Select a source exam mode in the exam modes list.
2. Click [Copy] to copy the parameters of the source exam mode.
3. Select a target exam mode.
4. Click [Paste] to paste the parameters to the target exam mode.
To rename an exam mode
1. Select an exam mode in the exam modes list.
2. Click [Rename] to open the “Rename” dialog box.
3. Input the name of new exam mode.
To export parameters of an exam mode
1. Select an exam mode in the exam modes list.
2. Click [Export] to open the “Export Data” dialog box.
3. Select the path of the exported data and name the data.
To load parameters of an exam mode
1. Click [Load] to open the “Load Data” dialog box.
2. Select the data to be imported.
Export All
1. Click [Export All] to open the “Export Data” dialog box.
2. Select a disk.
Others
Select an exam mode, and click [Measure Preset], [Comment Preset] or [Image Preset] to
configure the parameters of the selected exam mode. Refer to relevant chapters for details.
9.4 Image Preset

“Image Preset” is used to configure the parameters corresponding to exam modes, image modes
and transducers. For detailed information about the parameters, please refer to “4 Optimizing the
Image”.
1. Select an exam mode.
2. Select an image mode.
3. Select a transducer.
4. Configure the image parameters according to the following tables.
Preset 9-7
B/THI
A.Power Drop-down list To set the default acoustic power.
TSI Drop-down list To set the default TSI.
To configure the B Map/THI Map. Refer to the
B Map/THI Map Button
following segments for detailed operations.
Depth Drop-down list To set the default depth.
Checked/Unchecked: For transducers that support
THI Check box harmonic, you can set harmonic as default
frequency when this item is checked.
Frequency Drop-down list To set the default frequency.
Scan Angle Drop-down list To set the default scan angle: 0, 1, 2, 3.
F.Position Drop-down list To set the default focus position.
Focus Number Drop-down list To set the default number of focuses.
Gain Drop-down list To set the default gain.
To set the default THI gain. This item is available
THI Gain Drop-down list
for transducers that support harmonic only.
To set the default scanning density: Hi Frm Rate,
Line Density Drop-down list
Hi Density 1 and Hi Density 2.
To set the default horizontal flipping mode: Left,
L/R Flip Radio button
Right.
U/D Flip Radio button To set the default vertical flipping mode: Up, Down.
To set whether to rotate the image or not: 0, 90,
Rotation Drop-down list
180, 270.
B IP Drop-down list To set the default B IP: 1~8.
To set the default THI IP: 1~8. This item is
THI IP Drop-down list available for transducers that support harmonic
only.
To configure the parameters of B IP/THI IP. Refer
to the following segments for detailed operations.
B IP/THI IP Button
The THI IP is available for transducers that support
harmonic only.
M
Speed Drop-down list To set the default M scanning speed.
To configure the M Map. Refer to the following
M Map Button
segments for detailed operations.
M Gain Drop-down list To set the default M Gain.
M Map Drop-down list To set the default M Map.
Edge Enhance Drop-down list To set the default parameter of Edge Enhance.
M IP Drop-down list To set the default M IP.
9-8 Preset
To configure the M IP. Refer to the following
M IP Button
segments for detailed operations.
B/THI Map
1. Click [B Map]/[ THI Map] to open the “Effect” dialog box.
2. Select the grey map to be configured.
3. Configure the “Grey Curve”, “Grey Rejection” and “γ” (please refer to “4.2.13 B/M Post
Process” for details), or click “Record Current” to record the current parameters as preset.
B/THI IP/M IP
1. Click [B IP]/[THI IP] to open the “B IP”/“THI IP”/“M IP” dialog box.
2. Configure the parameters of “Dyn Rng (Dynamic Range)”, “Img Enhance (Image
Enhance)” and “Frame Avg (Frame Average)” (for B/THI IP) or “Dyn Rng (Dynamic
Range)” and “M Soften” (for M IP) in the corresponding drop-down list.
Record Current: Record the current parameters as preset.
Load Factory: Restore all parameters in this page to factory default.
9.5 Measure Preset
9.5.1 Measure
This system provides a measurement library, including Measurement, Calculate and Study items of
General, Abdomen, Gynecology, Cardiac, Vascular, Urology, Small Parts, ORTH and Obstetric.
To configure the measurement package
1. Select an exam mode.
2. Input the name of the measurement package. To manage the measurement package,
click [Advanced].
3. Select a scan mode. If “Use same menu for all scan mode” is selected, you need not to
select the scanning mode.
4. Select the type of the measurement item.
5. Add/delete items for measurement package:
h [>]: Select an item in “Available Items”, and click [>] to add it to “Selected Items”;
h [>>]: Click [>>] to add all items in the “Available Items” to the “Selected Items”;
h [<]: Select an item in “Selected Items”, and click [<] to delete it;
h [<<]: Click [<<] to delete all items in “Selected Items”;
h Sort: Select an item in “Selected Items”, and then click [Move Up] or [Move Down] to
move it up/down.
h [Default]: Select an item in “Selected Items”, and click [Default] to set it as default
measurement items.
6. To set the measure sequence of the measurement package:
h None: After the measurement, the cursor returns to the measurement menu;
h Repeat: After the measurement, the system automatically activates the current item
again;
Preset 9-9
h Next: After the measurement, the system automatically activates the next item in the
menu.
To manage the measurement package: Click [Advanced] to manage the measurement
package.
z [>]: Select a package in “Available Items”, and click [>] to add it to “Selected Items”;
z [>>]: Click [>>] to add all packages in the “Available Items” to the “Selected Items”;
z [<]: Select a package in “Selected Items”, and click [<] to delete it;
z [<<]: Click [<<] to delete all packages in “Selected Items”;
z Sort: Select a package in “Selected Items”, and then click [Move Up] or [Move Down] to
move it up/down.
z [Default]: Select a package in “Selected Items”, and then click [Default] to set it as the
default measurement package of current exam mode;
z [New]: Click [New] to create a new package;
z [Delete]: Select a package in “Available Items”, and click [Delete] to delete it.
9.6 Comment Preset

“Comment Preset” is used to configure the comment library for each exam mode.
To configure the comment libraries
1. Select an exam mode in the “Exam Mode” drop-down list.
2. Input the name of the comment library.
3. To add/delete comment words for this library:
h [>]: Select a word in “Available Items”, and click [>] to add it to “Selected Items”;
h [>>]: Click [>>] to add all words in the “Available Items” to the “Selected Items”;
h [<]: Select a word in “Selected Items”, and click [<] to delete it;
h [<<]: Click [<<] to delete all words in “Selected Items”;
h Sort: Select a word in “Selected Items”, and then click [Move Up] or [Move Down] to
move it up/down.
To edit a comment
1. Select an item in “Selected Items”, and the item turns to editing mode.
2. Edit the comment.
3. To add the edited comment to comment library: Click [<] to move the item to “Available
Items”.
To add a new comment
1. Click the last row of “Selected Items”, and the row turns to editing mode.
2. Input a new comment.
3. To add the edited comment to comment library: Click [<] to move the item to “Available
Items”.
[Delete]: Select a user-defined comment in “Available Items”, and click [Delete] to delete it.
[Load Factory]: Restore the comment library with factory data.
9-10 Preset
9.6.1 Comment Library
Descriptions of abbreviations used in the comment library are as follows:
Abdomen
Abbreviation Description Abbreviation Description
Rt Lobe Right Lobe of Liver GB Gall Bladder
Lt Lobe Left Lobe of Liver CHD Common Hepatic Duct
Caudate Caudal Lobe CBD Common Bile Duct
Lig.teres Ligamentum Teres Hepatis Splenic A Splenic Artery
Lig.venosum Ligamentum Venosum Splenic V Splenic Vein
Rt Hepatic V Right Hepatic Vein Rt Kidney Right Kidney
Mid Hepatic V Middle Hepatic Vein Lt Kidney Left Kidney
Lt Hepatic V Left Hepatic Vein Adrenal Adrenal Gland
Hepatic V Hepatic Vein RT Right
Hepatic A Hepatic Artery LT Left
Portal V Portal Vein Prox Proximal
IVC Inferior Vena Cava Mid Middle
SMA Superior Mesenteric Artery Sag longitudinal
SMV Superior Mesenteric Vein XS Transverse
Cardiology
Post Mitral
RV Right Ventricle Posterior Mitral Leaflet
Leaflet
LV Left Ventricle NCC Non coronary cusp
RA Right Atrium RCC Right coronary cusp
LA Left Atrium LCC Left coronary cusp
Ao Aorta LVPW Left Ventricle Posterior Wall
PA Pulmonary Artery RVAW Right Ventricle Anterior Wall
PV Pulmonary Vein Chordae Chordae Tendineae
SVC Superior Vena Cava Papillary Papiuary Muscle
IVC Inferior Vena Cava Coronary A Coronary Artery
Right Ventricle Outflow
RVOT ASD Atrial Septal Defect
Tract
Left Ventricular Outflow
LVOT VSD Ventricular Septal Defect
Tract
IAS Interatrial Septum Valsalva Valsalva
IVS Interventricular Septum RT Right
MV Mitral Valve LT Left
Preset 9-11
AV Aortic Valve Prox Proximal
TV Tricuspid Valve Mid Middle
PV Pulmonary Valve Sag longitudinal
Ant Mitral Leaflet Anterior Mitral Leaflet XS Transverse
GYN
GYN Gynecology Ca++ Calcify
Endo Endometrium RT Right
Rt Ovary Right Ovary LT Left
Lt Ovary Left Ovary Prox Proximal
Rt Kidney Right Kidney Mid Middle
Lt Kidney Left Kidney Sag longitudinal
Uterus A Uterus Artery XS Transverse
OB
OB Obstetric Rt Foot Right Foot
GS Gestational Sac Lt Foot Left Foot
3V Cord 3 Vessel Cord Umb A Umbilical Artery
AF Amnionic Fluid Umb V Umbilical Vein
Heart 4CH Heart four chamber Endo Endometrium
Right ventricular outflow
RVOT Fallopian tube Fallopian tube
tract
LVOT Left ventricular outflow tract Uterus A Uterus Artery
C-Spine Cervical Spine RT Right
T-Spine Thoracic Spine LT Left
L-Spine Lumbar spine Prox Proximal
S-Spine S-Spine Mid Middle
Rt Kidney Right Kidney Sag longitudinal
Lt Kidney Left Kidney XS Transverse
Rt Hand Right Hand
Lt Hand Left Hand
9-12 Preset
Urology
Lt Seminal
Lt Kidney Left Kidney Left Seminal Vesicle
Vesicle
Rt Seminal
Rt Kidney Right Kidney Right Seminal Vesicle
Vesicle
Calices Renal Calices Rt Testicle Right Testicle
Pyramid Renal Pyramid Lt Testicle Left Testicle
Column Renal Column RT Right
Renal A Renal Artery LT Left
Renal V Renal Vein Prox Proximal
Trans Zone Transitional Zone Mid Middle
Periph Zone Peripheral Zone Sag longitudinal
XS Transverse
SMP
Rt Lower
Thyroid Thyroid Right Lower Extremity
Extremity
Lt Lower
Lt Thyroid Left Thyroid Left Lower Extremity
Extremity
Rt Thyroid Right Thyroid RT Right
Sup Thy A Superior Thyroid Artery LT Left
Inf Thy A Inferior Thyroid Artery Prox Proximal
Rt Breast Right Breast Mid Middle
Lt Breast Left Breast Sag longitudinal
XS Transverse
Vascular
CCA Common Carotid Artery Ax V Axillary Vein
BIF Bifurcation Cephalic V Cephalic Vein
Buld Bulb Basilic V Basilic Vein
ICA Internal Carotid Artery Ulnar V Ulnar Vein
ECA External Carotid Artery Radial V Radial Vein
Vert A Vertebral Artery CIV Common Iliac Vein
Jugular V Jugular Vein IIV Internal Iliac Vein
Subc A Subclavian Artery EIV External Iliac Vein
Innom A Innominate Artery SFV Superficial Femoral Vein
ACA Anterior Cerebral Artery Profund V Profunda Femoral Vein
Preset 9-13
MCA Middle Cerebral Artery CFV Femoral Vein
PCA Posterior Cerebral Artery Saphenous Saphenous Vein
Basilar A Basilar Artery Pop V Popliteal Vein
Ax A Axillary Artery Tp-Trunk V Tibial Peroneal Trunk Vein
Brahc A Brachial Artery Innom V Innominate Vein
Ulnar A Ulnar Artery Sural V Sural Vein
Radial A Radial Artery Soleal V Soleal Vein
CIA Common Iliac Artery Ant Tibial V Anterior Tibial Vein
IIA Internal Iliac Artery Post Tibial V Posterior Tibial Vein
EIA External Iliac Artery Peroneal V Peroneal Vein
CFA Common Femoral Artery Artery Artery
SFA Superficial Femoral Artery Vein Vein
PFA Profunda Femoral Artery Valsalva Valsalva
Pop A Popliteal Artery RT Right
Ant Tibial A Anterior Tibial Artery LT Left
Post Tibial A Posterior Tibial Artery Prox Proximal
Tp-Trunk A Tibial Peroneal Trunk Mid Middle
Peroneal A Peroneal Artery Sag longitudinal
Dorsalis Pedis A Dorsalis Pedis Artery XS Transverse
Subc V Subclavian Vein
9-14 Preset
9.7 DICOM
This item is only available for systems configured with DICOM.
Before configuring DICOM, please read the DICOM CONFORMANCE STATEMENT of this system
and SCPs such as PACS, RIS or HIS to make sure the SCU service is supported by the SCPs.
System Name: It is the same as “AE Title”.
Institution Name: Input the name of the institution using this system.
Network Information
NOTE DO Not edit IP address in Network Preset page as the network task is executed,
otherwise it fails. View if there is any undergoing task in task manager of the system.
AE Title Host Name IP Address Port Alias Packet Size

Local It must be Customized Assign an It must be Customized Indispens-
consistent Indispens- available IP consistent Dispensable able
with that of able address to with that of
the server. the system. the server.
Indispens- Indispens- Indispens-
able able able
Server1 It must be Customized Input the IP It must be Customized Indispens-
consistent Indispens- address of consistent Dispensable able
with that of able the server. with that of
the server. Indispens- the server.
Indispens- able Indispens-
able able
Server2 Dispensable. Refer to Server1 for details.
Server3 Dispensable. Refer to Server1 for details.
The range of packet size is: 4096~65536.
The range of port is: 1~65535.
[Verify]: After configuring the network information, exit “DICOM Preset” and click [Return] to
validate the configurations. Then enter [Preset]Æ[DICOM Preset] again, and click [Verify] to
verify the configuration.
Local
z Subnet Mask: Input the Subnet Mask according to practical situation.
z Gateway: Input the IP address of the gateway according to practical situation.
Server: To set the default server for different services, select a server in the drop-down list.
z Current Storage Server
z Current Worklist Server
z Current Print Server
Print Parameter
Drop-down
Copies Select or input the copies of files to be printed.
list/Text box
8INX10IN, 8_5INX10IN, 10IN×12IN, 10IN×14IN,
Film Size Drop-down list 11INX14IN, 11INX17IN, 14INX14IN, 14INX17IN, 24cm×
24cm, 24cm×30cm, A4, A3
Preset 9-15
Medium Type Drop-down list Paper, Clear Film, Blue Film
Trim Drop-down list Yes, No
Settings Drop-down list RGB, Gray
Min Density Text box Input a number representing minimum density.
Max Density Text box Input a number representing maximum density.
Priority Drop-down list High, Medium, Low
Film Orientation Drop-down list LANDSCAPE, PROCESSOR
Film Destination Drop-down list MAGAZINE/ PROCESSOR
STANDARD\1,1; STANDARD\2,2; STANDARD\2,3;
Display Format Drop-down list
STANDARD\5,6;
Magnification Input type of magnification: REPLICATE/ BILINEAR/
Drop-down list
Type CUBIC/ NONE
Configuration Info Text box Specified image quality control information of printers.
OK Button Save and exit.
Cancel Button Cancel and exit.
9.8 Manage Settings

Export
1. Select the items to be exported and click [Export].
2. Select the path.
3. Click [OK] to export or click [Cancel] to cancel.
Import
z [Restore Factory]: Select a category and click [Restore Factory] to reset it.
z Import
1. Select the items to be imported and click [Import].
2. Select the path and the preset data to be imported (*.DTA).
3. Click [OK] to import or click [Cancel] to cancel.
[Export All]: To export all the items.
[Import All]: To import all the items.
[Restore Factory]: To restore all items to factory default.
[Exit]: To exit.
9.9 Maintenance
The [Maintenance] is for updating of system software or other special requirements. Contact your
service representative if necessary.
9-16 Preset
10 Network Print
The ultrasound system supports report printing via network.
10.1 Application Software on PC End

You should install application software on PC before printing via network.
1. Connect the PC with local or network printer.
2. Copy the folder PSPrinterServer (include the folder system, file gsdll32.dll and file
PSPrinterServer.exe) to the PC.
3. Double click the file PSPrinterServer.exe and the icon will appear in the lower right corner
in PC.
4. Set the port: click the right button of the mouse on the icon, click [Port Setting] in the
popped up menu to enter the port setting dialogue box. Usually, the port is set as the default
value 6666.
10.2 Network Print

1. Connect the ultrasound system and PC into the same LAN.
2. Set print type: press <Setup>, enter [Setup]-> [System Preset]-> [General]-> [Print Type],
select "Ultrapartner Print" from the drop-down list.
3. Click [>>] button to set the Current Print Server:
IP Address: the IP address of the PC which has installed the print software.
Port: the same setting as in PC (6666 by default).
4. Print:
(1) Click [Print] in the Report page.
(2) The report will be printed in the default printer of the PC, and you can check the report
print status by clicking in PC.
Network Print 10-1

(3) PS_SPOOL temporary folder will be created in drive C in PC, and the folder will be
automated deleted after exiting print application program.
NOTE: 1. It's suggested that not to perform abnormal network operations, as some network
abnormity will lead to the system timeout that lasts from several to tens of minutes,
especially when detaching the network cable during connecting and printing
process.
2. The same application as PSPrinterServer can not be running at the same time on
the PC end, otherwise will cause the network abnormity or communication failure.
3. The port of the PSPrinterServer can not set to 0, which is not supported by the
ultrasound system.
10-2 Network Print

11 Cleaning and Maintaining the
System
This chapter introduces how to clean and maintain the system.

1. Only an authorized Mindray service engineer can perform
maintenance not specified in this operator’s manual.
WARNING: 2. For the sake of the system performance and safety, you should
perform periodical checks for the system.
11.1 Daily Maintenance
11.1.1 Cleaning the System

Before cleaning the system, be sure to turn off the power and
WARNING: disconnect the power cord from the outlet. If you clean the system
while the power is On, it may result in electric shock.
CAUTION: 1. Do not spill water or other liquid into the system while you perform the
cleaning. Otherwise it may result in malfunction or electric shock.
2. When you want to clean transducer connectors and TGC sliders,
contact Mindray Customer Service Department or sales representative.
Cleaning it yourself may result in malfunction or degradation of the
performance.
Cleaning the transducer
Please refer to the operator’s manual of the corresponding transducer to perform cleaning and
disinfection.
Cleaning the transducer cable
z Use soft dry cloth to wipe off stains from the transducer cable.
z If it is difficult to clean the stains thoroughly, use soft cloth dipped with mild detergent, and
then let the cable air dry.
Cleaning the monitor
Using a soft cloth, apply a glass cleaner directly to the cloth and wipe down the monitor to
remove finger marks, dust and smudges. Allow the monitor to air-dry.
Cleaning the control panel, cover and bracket
Use dry soft cloth to clean the surface of the system. If the system is dirty, moisten the soft
cloth with a mild or neutral detergent and wipe off any stains. Use dry soft cloth to remove any
moisture and allow all hard surfaces to completely air-dry.
Cleaning and Maintaining the System 11-1

NOTE: Do not use hydrocarbon glass cleaner or cleaner for OA (Office Automation) equipment
to clean the monitor. These substances may cause deterioration of the monitor.
11.1.2 Backup of Data

For systems configured with hard disk, back up the data in hard disk periodically to avoid data
corruption or loss.
11.2 Maintenance Checks by Service Engineer

Type Items
Interior of the system
Cleaning
Peripherals
Ground leakage current
Enclosure leakage current
Electric safety Patient leakage current
Patient leakage current (110% supply voltage on
applied part)
Monitor mounting mechanism
Control panel
Mechanical safety Mounting mechanism for the peripheral devices
Check other mechanical structures
Check the transducer appearance
Images in each mode
Image recording
Image recording by using the standard transducer
11.3 Consumables and Periodic Part

Replacement
This system contains some consumables and parts requiring periodic replacement.
Before replacing them, please contact Mindray Customer Service Department or sales representative
for instructions.
11.4 Troubleshooting
To ensure proper system operation and function, it is recommended that a maintenance and
inspection plan be established to periodically check the safety of the system. If any system
malfunction is experienced, contact Mindray Customer Service Department or sales representative.
If any persistent system malfunction is experienced, please refer to the following table below. If the
failure cannot be eliminated, please contact Mindray Customer Service Department or sales
representative.
11-2 Cleaning and Maintaining the System

No. Malfunction Potential Causes Corrective Measures
After the power
Abnormal power system or Verify that the plug has not
supply is turned on,
1 incorrect connection of the become loosened or dislodged
the power indicator
power cord. from the back of the system.
does not light on.
The interval between turnoff Turn off the system and wait
When the power and restart is too short – wait minimum 1 minute, then restart
indicator of the minimum 20 seconds. the system.
2
monitor is on and Adjust the monitor brightness
image is blank. The monitor brightness or
and contrast back to factory
contrast may be improperly set.
defaults.
The transmission power, overall
Adjust the transmission power,
gain or TGC controls are
gain or TGC control.
improperly set.
The monitor displays
3 the characters but no Verify that a transducer is
Ensure proper transducer
images. connected and / or fully
connection.
connected.
The image is frozen. Unfreeze the image.
Select an appropriate exam
The exam type is not correct.
type.
Adjust the settings of the image
The image quality The settings of the image post via post processing or reset the
4
has degraded processing are not correct. post processing to the default
values.
The image presets are Reset the factory default
appropriate setups.
The display of image
is abnormal.
System error
messages are
5 / Restart the System
displayed all the
time.
Operations cannot
be executed.
Cleaning and Maintaining the System 11-3

12 Acoustic Output
This section of the operator’s manual applies to the overall system including the main unit,
transducers, accessories and peripherals. This section contains important safety information for
operators of the device, pertaining to acoustic output and how to control patient exposure through
use of the ALARA (as low as reasonably achievable) principle.
Read this information carefully before using the system.
12.1 Concerns with Bioeffects

Diagnostic ultrasound is recognized as being safe. In fact, there have been no reports of injuries to
patients caused by diagnostic ultrasound.
It cannot be stated categorically that ultrasound is 100% safe. Studies have revealed that
ultrasound with extremely high intensity is harmful to body tissues.
Diagnostic ultrasound technology has made a great leap forward during the last several years.
This rapid advance has generated concerns about the potential risk of bioeffects when new
applications or diagnostic technologies become available.
12.2 Prudent Use Statement

Although there are no confirmed biological effects on patients caused by exposures from present
diagnostic ultrasound instruments, the possibility exists that such biological effects may be
identified in the future. Thus ultrasound should be used in a prudent manner to provide medical
benefit to the patient. High exposure levels and long exposure times should be avoided while
acquiring necessary clinical information.
12.3 ALARA Principle (As Low As Reasonably

Achievable)
It is required to practice ALARA when using ultrasound energy. Practicing ALARA ensures that the
total energy level is controlled below a low enough level at which bioeffects are not generated
while diagnostic information is being accumulated. The total energy is controlled by output intensity
and total radiation time. The output intensity necessary for examinations differs depending on the
patient and the clinical case.
Not all examinations can be performed with an extremely low level of acoustic energy. Controlling
the acoustic level at an extremely low level leads to low-quality images or insufficient Doppler
signals, adversely affecting the reliability of the diagnosis. However, increasing the acoustic power
more than necessary does not always contribute to an increase in quality of information required
for diagnosis, rather increasing the risk of generating bioeffects.
Users must take responsibility for the safety of patients and utilize ultrasound deliberately.
Deliberate use of ultrasound means that output power of ultrasound must be selected based on
ALARA.
Acoustic Output 12-1

Additional information regarding the concept of ALARA and the possible bioeffects of Ultrasound is
available in a document from the AIUM (American Institute of Ultrasound Medicine) title “Medical
Ultrasound Safety”.
12.4 Measurement Uncertainty

Total Uncertainty for
16.4 %
Mechanical Index
Non-scan Mode Scan-Mode Combined-Mode
32.9% or 5.1% ( A aprt >1)

Total Uncertainty for TIS 32.9% 5.1%
33.4% ( A aprt ≤1)
Total Uncertainty for TIB 32.9% 5.1% 32.9% or 5.1%

Total Uncertainty for TIC 32.9% 5.1% 33.4%
12.5 Limits of Acoustic Output

For any transducer in any operating mode, the acoustic output parameters MI/TI are less than 1.0.
12.6 Parameters Affecting Acoustic Power

Acoustic Power is affected by transmission conditions (focus, drive frequency, voltage applied to
piezoelectric elements, etc.), scan conditions, and settings of the control panel, and preset menu.
12.7 Acoustic Power Setting

Adjusting Acoustic Power
Rotate <A.Power> knob to adjust the acoustic power, and its value is displayed in the
parameters area at the top of the screen. Rotate the knob clockwise to increase the acoustic
power, and rotate the knob anticlockwise to decrease the acoustic power.
Acoustic power can be set in the range from 0 to 15, where 0 represents minimum acoustic power
and 15 represents maximum acoustic power.
When the image is frozen, the system stops transmitting acoustic power.
Default setting of acoustic power
Selection of diagnostic applications is the most important factor for controlling ultrasound
output. The permissible level of intensity of ultrasound differs depending on the region of
interest. For fetal examinations, in particular, much care must be exercised.
In this system, imaging setups can be created using the ultrasound output set by you. At this
time, the default function is disabled. It is the user’s responsibility for any change to the default
settings.
12-2 Acoustic Output

12.8 Operations That Change Acoustic Output
Power
Operations Affections on Acoustic Output
The maximum acoustic output power of each transducer is optimized to
Changing transducers produce the best image quality within FDA guidelines. Thus, the acoustic
output power will change as the operator changes the active transducer.
Since B and M modes use difference default imaging parameters,
changing the mode will change the acoustic output power of the system.
Changing imaging No changes occur when switching from B to B/B, since the basic imaging
mode parameters remain the same. In most cases, the acoustic output power
for M-mode is larger than in B-mode, however, it depends in the specific
presets for B and M-mode.
Field of view (sector Change the sector angle or scan width may result in change to the frame
Angle or scan Width) rate, and thus change the acoustic output power.
Changing the image depth changes the PRF, and thus changes the
Changing image depth
acoustic output power.
Since the number of focal zones influences the frame rate and the actual
Number of Focal
position of the focal zones, changing the number of focal zones changes
Zones
the acoustic output power.
The transmit focus location change will cause the acoustic output power
Changing focus change, even though the transmitting electrical energy level and the
position aperture remains the same. In most cases, the acoustic output power will
increase if the focal point is moved closer to the transducer.
Active the freeze function stops the electrical energy transmit part of the
Freezing
system, thus disabling the system from generating ultrasound wave.
The transmit power level change will change the electrical output of the
Transmit power
system to the transducer, and thus change the acoustic output power.
Changing the operating frequency changes the focal characteristics of
Changing frequency
the acoustic waves, thus changes the acoustic output power.
Changing the number of acoustic lines generated (line density) affects
Line density
the acoustic output power.
Since the system and user presets contain all of the above imaging
Preset
parameters, changing the preset will change the acoustic output power.
Resetting or powering the system on or off causes the system to return
Reset or Power Off/On
to the default status thus may change the acoustic output power.
12.9 References for Acoustic Power and Safety

1. “Bioeffects and Safety of Diagnostic Ultrasound” issued by AIUM in 1993
2. “Medical Ultrasound Safety” issued by AIUM in 1994
3. “Information for Manufacturers Seeking Marketing Clearance of Diagnostic Ultrasound
Systems and Transducers” issued by FDA in 2008.
Acoustic Output 12-3

Appendix A Accuracy of
Measurement
Within the selected field range, the measurement accuracy is ensured within the range mentioned
above. The accuracy specifications are performance in the worst conditions, or based on the real
test for the system.
Depth and time
Item Value Range Error Range
Depth Maximum 300 mm ≤±4% of full scale
M-mode image time Maximum 8s ≤±0.3% of full scale
Accuracy of Measurement
≤±4%, or <2 mm if measured value is
Distance/Depth Maximum 300 mm
less than 40 mm
≤±8%, or <130 mm 2 if measured value
Area (Trace) Maximum 884 cm2
is less than 1600 mm 2
≤±8%, or <130 mm 2 if measured value
Area (Ellipse) Maximum 884 cm 2
is less than 1600 mm 2
Angle 0~180° ≤±3%
%stenosis Maximum 1.0 Max. 1.0 ≤±7%
Time/Motion Measurements
≤±4%, or <2 mm if measured value is
Distance Maximum 300 mm
less than 40 mm
Time Maximum 8s ≤±1%
Heart Rate 15~999 beats per minute ≤±5%
Slope Maximum 999mm / s ≤±5%
Volume Measurements
≤±12%, or <8000 mm 3 if measured
Volume Maximum 999 cm3
value is less than 64000 mm 3
Accuracy of Measurement A-1

Appendix B Safety Classification
No. Standard of Classification Type of Product
According to the type of protection against
1 CLASS I EQUIPMENT
electric shock
According to the degree of protection EQUIPMENT WITH TYPE-BF APPLIED
2
against electric shock PARTS
Degree of protection against harmful ingress Enclosure: IPX0, transducers: IPX7, foot
3
of water switch: IP68.
According to the degree of safety of
EQUIPMENT not suitable for use in the
application in the presence of a
presence of a FLAMMABLE ANESTHETIC
4 FLAMMABLE ANESTHETIC MIXTURE
MIXTURE WITH AIR or WITH OXYGEN OR
WITH AIR or WITH OXYGEN OR NITROUS
NITROUS OXIDE
OXIDE
5 According to the mode of operation CONTINUOUS OPERATION
PORTABLE EQUIPMENT
6 According to the Degree of Mobility MOBILE EQUIPMENT (when mounted onto
the mobile trolley)
Safety Classification B-1

Appendix C Guidance and
Manufacturer's
Declaration
The system complies with the EMC standard IEC60601-1-2: 2001+A1:2004。
WARNING: The use of unapproved accessories may diminish system performance.
NOTE: 1. Use of accessories, transducers, and cables other than those specified may result
in increased emission or decreased immunity of system.
2. This system should not be used adjacent to or stacked with other equipment. If
adjacent or tacked use is necessary, this system should be observed to verify
normal operation in the configuration in which it will be used.
3. This system needs special precautions regarding EMC and needs to be installed
and put into service according to the EMC information provided below.
4. Preventing conducted RF immunity. Due to technological limitations, the conducted
RF immunity level are limited to 1Vrms level, conducted RF interference above
1Vrms may cause wrong diagnosis and measurements. We suggested that you
position this system further from sources of conducted RF noise.
5. Operation of system, in the case that the patient physiological signal is lower than
the minimum amplitude or value specified in the product specifications, may cause
inaccurate results.
6. Portable and mobile RF communications equipment can affects this system. See tables
1, 2, 3, and 4 below.
Guidance and Manufacturer's Declaration C-1

Table 1:
GUIDANCE AND MINDRAY DECLARATION—ELECTROMAGNETIC EMISSIONS
This system is intended for use in the electromagnetic environment specified below. The
customer or the user of this system should assure that it is used in such an environment.
EMISSIONS TEST COMPLIANCE ELECTROMAGNETIC ENVIRONMENT－GUIDANCE
RF emissions Group1 This system uses RF energy only for its internal function.
CISPR 11 Therefore, its RF emissions are very low and are not likely
to cause any interference in nearby electronic equipment.
RF emissions Class B This system is suitable for use in all establishments
CISPR 11 including domestic establishments and those directly
connected to the public low-voltage power supply network
Harmonic Class A that supplies buildings used for domestic purposes
Emissions IEC61000-
3-2
Voltage Fluctuations/ Compliance
Flicker Emissions IEC
61000-3-3
C-2 Guidance and Manufacturer's Declaration

Table 2:
GUIDANCE AND MINDRAY DECLARATION—ELECTROMAGNETIC IMMUNITY
This system is intended for use in the electromagnetic environment specified below.
The customer or the user of this system should assure that it is used in such an environment.
IMMUNITY IEC 60601 COMPLIANCE ELECTROMAGNETIC
TEST TEST LEVER LEVER ENVIRONMENT-
GUIDANCE
Electrostatic ±6 kV contact ±6 kV contact Floors should be wood,
Discharge(ESD) ±8 kV air ±8 kV air concrete or ceramic tile.
If floors are covered
IEC 61000-4-2 with synthetic material,
the relative humidity
should be at least 30%.
Electrical fast ±2 kV for power supply ±2 kV for power supply Mains power quality
Transient/burst lines ±1 kV for lines ±1 kV for should be that of a
input/output lines input/output lines typical commercial or
IEC 61000-4-4 (>3m). (>3m). hospital environment.
Surge IEC ±1 kV differential mode ±1 kV different mode ±2 Mains power quality
61000-4-5 ±2 kV common mode kV common mode should be that of a
typical commercial or
hospital environment.
Voltage dips, <5% UT <5% UT Mains power quality
Short interruptions and should be that of a
voltage variation on (>95% dip in UT ) for (>95% dip in UT ) for typical commercial or
power supply input 0.5 cycle 0.5 cycle hospital environment.
lines IEC 61000-4-11 If the user of our
product requires
40% UT 40% UT continued operation
during power mains
(60% dip in UT ) for 5 (60% dip in UT ) for 5 interruptions, it is
cycle cycle recommended that our
product be powered
from an uninterruptible
70% UT 70% UT power supply or a
battery.
(30% dip in UT ) for 25 (30% dip in UT ) for 25
cycle cycle
<5% UT <5% UT
(>95% dip in UT ) for 5 (>95% dip in UT ) for 5

sec sec
Power frequency 3 A/m 3 A/m Power frequency
(50/60 HZ) magnetic fields should
be at levels
magnetic field IEC characteristic of a
61000-4-8 typical location in a
typical commercial or
hospital environment.
UT is the A.C. mains voltage prior to application of the test level.

Table 3:
GUIDANCE AND MINDRAY DECLARATION—ELECTROMAGNETIC IMMUNITY
This system is intended for use in the electromagnetic environment specified below. The
customer or the user of this system should assure that it is used in such an environment
IMMUNITY IEC 60601-1-2 COMPLIANCE ELECTROMAGNETIC
TEST TEST LEVEL LEVEL ENVIRONMENT-GUIDANCE
Conduced RF 3 Vrms 150kHz Portable and mobile RF communications
1 Vrms
IEC 61000-4-6 to 80MHz equipment should be used no closer to any
part of this system, including cables, than the
recommended separation distance calculated
from the equation applicable to the frequency
of the transmitter.
Recommended separation distance
d = 3.5 x P
d = 1.2 x P 80 MHz to 800 MHz
d = 2.3 x P 800 MHz to 2.5GHz
Radiated RF 3 V/m 80MHz to where P is the maximum output power rating
3V/m
IEC 61000-4-3 2.5 GHz of the transmitter in watts (W) according to the
transmitter manufacturer and d is the
recommended separation distance in meters
(m).b
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey,
a should be less than the compliance level in
each frequency range b
Interference may occur in the vicinity of
equipment marked with the following symbol:
Note:
1. At 80 MHz and 800 MHz, the higher frequency range applies.
2. These guidelines may not apply in all situations. Electromagnetic propagation is affected
by absorption and reflection from structures, objects and people.
z Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the
electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey
should be considered. If the measured field strength in the location in which this system
is used exceeds the applicable RF compliance level above, this system should be
observed to verify normal operation. If abnormal performance is observed, additional
measures may be necessary, such as reorienting or relocating this system.
z Over the frequency ranges 150kHz to 80MHz, field strengths should be less than 1V/m.
C-4 Guidance and Manufacturer's Declaration

Table 4：
RECOMMENDED SEPARATION DISTANCES BETWEEN PORTABLE AND MOBILE RF
COMMUNICATION AND THIS SYSTEM
This system is intended for use in an electromagnetic environment in which radiated RF
disturbance are controlled. The customer or the user of This system can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communication equipment (transmitters) and This system as recommended below, according to
the maximum output power of the communication equipment.
Separation Distance According to Frequency of Transmitter
Rated Maximum M (Meters)
Output power of 150kHz -80MHz 80MHz -800MHz 800MHz -2.5GHz
Transmitter W (Watts)
d = 3 .5 P d = 1 .2 P d = 2 .3 P
0.01 0.35 0.12 0.23
0.1 1.11 0.37 0.74
1 3.50 1.17 2.34
10 11.07 3.69 7.38
100 35.00 11.67 23.34
For transmitters at a maximum output power not listed above, the recommended separation
distanced in meters (m) can be determined using the equation applicable to the frequency of the
transmitter, where P is the maximum output power rating of the transmitter in watts (W) according
to the transmitter manufacturer.
If image distortion occurs, it may be necessary to position this system further from sources of
conducted RF noise or to install external power source filter to minimize RF noise to an acceptable
level.
Note:
1. At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
2. These guidelines may not apply in all situations. Electromagnetic propagation is affected
by absorption and reflection from structures, objects and people.

Appendix D Electrical Safety
Inspection
The following electrical safety tests are recommended as part of a comprehensive preventive
maintenance program. They are a proven means of detecting abnormalities that, if undetected,
could prove dangerous to either the patient or the operator. Additional tests may be required
according to local regulations.
All tests can be performed using commercially available safety analyzer test equipment. These
procedures assume the use of a 601PROXL International Safety Analyzer or equivalent safety
analyzer. Other popular testers complying with IEC 60601-1 used in Europe such as Fluke, Metron,
or Gerb may require modifications to the procedure. Follow the instructions of the analyzer
manufacturer.
The electrical safety inspection should be periodically performed every two years. The
safety analyzer also proves to be an excellent troubleshooting tool to detect abnormalities of line
voltage and grounding, as well as total current loads.
D.1 Power Cord Plug
D.1.1 The Power Plug

Test Item Acceptance Criteria
The power plug pins No broken or bent pin. No discolored pins.
The plug body No physical damage to the plug body.
The power plug No physical damage to the strain relief. No
The strain relief
plug warmth for device in use.
The power plug No loose connections.
No physical damage to the cord. No
deterioration to the cord.
For devices with detachable power cords,
The power cord
inspect the connection at the device.
For devices with non-detachable power
cords, inspect the strain relief at the device.
Electrical Safety Inspection D-1

D.2 Device Enclosure and Accessories
D.2.1 Visual Inspection

No physical damage to the enclosure and
accessories.
No physical damage to meters, switches,
connectors, etc.
The enclosure and accessories
No residue of fluid spillage (e.g., water,
coffee, chemicals, etc.).
No loose or missing parts (e.g., knobs,
dials, terminals, etc.).
D.2.2 Contextual Inspection

No unusual noises (e.g., a rattle inside the
case).
The enclosure and accessories No unusual smells (e.g., burning or smoky
smells, particularly from ventilation holes).
No taped notes that may suggest device
deficiencies or operator concerns.
D.3 Device Labeling

Check the labels provided by the manufacturer or the healthcare facility are present and legible.
z Main unit label
z Integrated warning labels
D.4 Protective Earth Resistance

a. Plug the probes of the analyzer into the device’s protective earth terminal and protective earth
terminal of the AC power cord.
b. Test the earth resistance with a current of 25 A.
c. Verify the resistance is less than limits.
LIMITS
ALL COUNTRIES R = 0.2 Ω Maximum
D.5 Earth Leakage Test

Run an Earth Leakage test on the device being tested before performing any other leakage tests.
D-2 Electrical Safety Inspection

The following outlet conditions apply when performing the Earth Leakage test.
z normal polarity( Normal Condition);
z reverse polarity( Normal Condition);
z normal polarity with open neutral(Single Fault Condition);
z reverse polarity with open neutral(Single Fault Condition).
LIMITS
For UL60601-1,
z 300 μA in Normal Condition.
z 1000 μA in Single Fault Condition.
For IEC60601-1,
z 500 μA in Normal Condition.
D.6 Enclosure Leakage Test

The following outlet conditions apply when performing the Enclosure Leakage test.
z reverse polarity with open neutral(Single Fault Condition);
z normal polarity with open earth(Single Fault Condition);
z reverse polarity with open earth(Single Fault Condition).
LIMITS
For UL60601-1,
z 100μA in Normal Condition.
For IEC60601-1:
D.7 Patient Leakage Current

Patient leakage currents are measured between a selected applied part and mains earth. All
measurements have a true RMS only.
The following outlet conditions apply when performing the Patient Leakage Current test.
z reverse polarity( Normal Condition),
z reverse polarity with open neutral(Single Fault Condition).
LIMITS
For BF applied parts,

z 500μA in Single Fault Condition.
Electrical Safety Inspection D-3

D.8 Mains on Applied Part Leakage
The Mains on Applied Part test applies a test voltage, which is 110% of the mains voltage, through
a limiting resistance, to selected applied part terminals. Current measurements are then taken
between the selected applied part and earth. Measurements are taken with the test voltage
(110% of mains) to applied parts in the normal and reverse polarity conditions.
The following outlet conditions apply when performing the Mains on Applied Part test.
z Normal Polarity;
z Reversed Polarity.
LIMITS
z For BF applied parts: 5000 μA.
D.9 Patient Auxiliary Current

Patient Auxiliary currents are measured between any selected Applied Part connector and the
remaining Applied Part connectors. All measurements may have a true RMS only response.
The following outlet conditions apply when performing the Patient Auxiliary Current test.
z reverse polarity with open neutral(Single Fault Condition);
LIMITS
For BF applied parts,

z 500μA in Single Fault Condition.
Note: Make sure the safety analyzer is authorized comply with requirement of IEC61010-1.
Follow the instructions of the analyzer manufacturer.
D-4 Electrical Safety Inspection

P/N: 046-000617-00 (V8.0)

H 046 000617 00 8 0 - DP 6900 Ops Manual Basic Volume

Uploaded by

Copyright:

Available Formats

H 046 000617 00 8 0 - DP 6900 Ops Manual Basic Volume

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

H 046 000617 00 8 0 - DP 6900 Ops Manual Basic Volume

Uploaded by

Copyright:

Available Formats

DP-6900

Digital Ultrasonic Diagnostic

Safety Precautions .............................................................................................................. VI

1 Overview ...................................................................................................................... 1-1

2 Preparing the System ................................................................................................. 2-1

3 Beginning an Exam ..................................................................................................... 3-1

4 Optimizing the Image .................................................................................................. 4-1

5 Annotating the Image ................................................................................................. 5-1

6 Auxiliary Functions .................................................................................................... 6-1

7 File Management......................................................................................................... 7-1

8 Probes and Biopsy ..................................................................................................... 8-1

9 Preset ........................................................................................................................... 9-1

10 Network Print ............................................................................................................. 10-1

12 Acoustic Output ........................................................................................................ 12-1

Appendix A Accuracy of Measurement .................................................................... A-1

Intellectual Property Statement

Release, amendment, reproduction, distribution, rental, adaptation, translation or any other

Responsibility on the Manufacturer Party

This warranty shall not extend to:

Manufacturer: Shenzhen Mindray Bio-medical Electronics Co., Ltd.

Safety Precautions III

About This Manual

Software Interfaces in this Manual

Meaning of Signal Words

DANGER Indicates an imminently hazardous situation that, if not avoided, will

WARNING Indicates a potentially hazardous situation that, if not avoided, could

CAUTION Indicates a potentially hazardous situation that, if not avoided, may

Meaning of Safety Symbols

DANGER: Do not use flammable gasses, such as anesthetic gas or hydrogen, or

Safety Precautions VII

VIII Safety Precautions

XII Safety Precautions

Caution! Please carefully read this manual

Prohibit using system with flammable

The following labels are available

Medical equipment with respect to electric

Safety Precautions XIII

This chapter introduces the basic information of the system.

1.2 Product Specifications

1.2.1 Environmental Conditions

1.2.2 Dimensions and Weight

1.3.1 Standard Configuration

1.3.2 Transducers Available

1.3.4 Peripherals Supported

1.4.1 Introduction of Each Unit

Right side view

Left side view

No. Name Function

1.4.2 I/O Panel

No. Name Function

<2> <3> <4> <5> <6> <7> <8> <9> <10>

<13> <14> <15> <22>

No. Name Function

Dangerous voltage Inside the machine

Main switch OFF

Video printing control

2.1 Setup and Connections

2.1.1 Moving and Placing the System

2.1.2 Connecting the Power Cord

Disconnecting the transducer

To open the “Patient Info” dialog box: