TN1433

Technical note

Reference device marking schematics for STM32 microcontrollers and

microprocessors

Introduction

This document provides the most probable(1) device marking example for every(2) package code encountered in STM32
general-purpose microcontrollers or microprocessors.
The package code is a unique package identifier that can be found:
• in this document, between parenthesis, at the end of each section title
• in this document, as a fragment of the index located at each figure bottom-right corner
• in the product datasheet, as a fragment of the index located at the bottom-right corner of package outline figures.
(1): Some slight package marking variations may be encountered between different products using the same package,
and even between two identical products (in case of multiple assembly plants for instance). Nevertheless, the pin1/ballA1
localisation instructions provided in this document apply invariably.
(2): Except wafer level chip scale packages (WLCSP).

Table 1. Applicable products

Type Sub class

STM32 Wireless MCUs

STM32 Ultra Low Power MCUs
Microcontrollers
STM32 Mainstream MCUs
STM32 High Performance MCUs
Microprocessors STM32 Arm Cortex MPUs

TN1433 - Rev 1 - January 2023 www.st.com

For further information contact your local STMicroelectronics sales office.
 TN1433
General information

1 General information

This document applies to STM32 Arm®-based general-purpose microcontrollers or microprocessors.

Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.

TN1433 - Rev 1 page 2/60

 TN1433
Device marking for SO8N (O7)

2 Device marking for SO8N (O7)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 1. SO8N marking example (package top view)

Product
identification(1)
Revision code

Date code

Pin 1 Y WW
indentifier

O7_SO8N_DM_V4
1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples
in production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 3/60

 TN1433
Device marking for TSSOP14 (6R)

3 Device marking for TSSOP14 (6R)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 2. TSSOP14 marking example (package top view)

Product
identification(1)

Date code

Revision
Y WW code

6R_TSSOP14_DM_V2
Pin1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 4/60

 TN1433
Device marking for TSSOP20 (YA)

4 Device marking for TSSOP20 (YA)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 3. TSSOP20 marking example (package top view)

Product
identification(1)

YA_TSSOP20_DM_V2
Pin1 identifier Revision
Y WW code

Date code

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples
in production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 5/60

 TN1433
Device marking for LQFP32 (5V)

5 Device marking for LQFP32 (5V)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 4. LQFP32 marking example (package top view)

Product
identification (1)

Date code

Y WW

Revision code

5V_LQFP32_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 6/60

 TN1433
Device marking for LQFP44 (4Y)

6 Device marking for LQFP44 (4Y)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 5. LQFP44 marking example (package top view)

Product
identification (1)

Date code
Y WW

4Y_LQFP44_DM_V1
Pin 1 identifier Revision code

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 7/60

 TN1433
Device marking for LQFP48 (5B)

7 Device marking for LQFP48 (5B)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 6. LQFP48 marking example (package top view)

Product
identification (1)

Date code

Y WW

Revision code

5B_LQFP48_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 8/60

 TN1433
Device marking for LQFP64 (5W)

8 Device marking for LQFP64 (5W)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 7. LQFP64 marking example (package top view)

Revision code

Product
identification (1)

Date code
Y WW

5W_LQFP64_DM_V2
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 9/60

 TN1433
Device marking for LQFP64 (1R)

9 Device marking for LQFP64 (1R)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 8. LQFP64 marking example (package top view)

Revision code

Product
identification (1)

Date code

Y WW

1R_LQFP64_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 10/60

 TN1433
Device marking for LQFP80 (9X)

10 Device marking for LQFP80 (9X)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 9. LQFP80 marking example (package top view)

Product
identification (1)

Revision code

Y WW Date code

9X_LQFP80_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 11/60

 TN1433
Device marking for LQFP80 (1S)

11 Device marking for LQFP80 (1S)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 10. LQFP80 marking example (package top view)

Revision code

Product
identification (1)

Y WW Date code

1S_LQFP80_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 12/60

 TN1433
Device marking for LQFP100 (1L)

12 Device marking for LQFP100 (1L)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 11. LQFP100 marking example (package top view)

Product
identification(1)

Y WW Date code

1L_LQFP100_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 13/60

 TN1433
Device marking for LQFP128 (TC)

13 Device marking for LQFP128 (TC)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 12. LQFP128 marking example (package top view)

Product
identification(1)

Revision
code
Date code

Y WW

TC_LQFP128_DM_V2
Pin 1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples
in production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 14/60

 TN1433
Device marking for LQFP144 (1A)

14 Device marking for LQFP144 (1A)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 13. LQFP144 marking example (package top view)

Revision code

Product
identification(1)

Y WW Date code

1A_LQFP144_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 15/60

 TN1433
Device marking for LQFP176 (1T)

15 Device marking for LQFP176 (1T)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 14. LQFP176 marking example (package top view)

Product
identification(1)

Y WW Date code

1T_LQFP176_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 16/60

 TN1433
Device marking for LQFP208 (UH)

16 Device marking for LQFP208 (UH)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 15. LQFP208 marking example (package top view)

Revision code
Product
identification(1)

Pin 1identifier
Date code
Y WW

UH_LQFP208_DM_V1
1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples
in production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 17/60

 TN1433
Device marking for UFQFPN20 (A0A5)

17 Device marking for UFQFPN20 (A0A5)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 16. UFQFPN20 marking example (package top view)

Product
identification(1)

Revision
Y WW

A0A5_UFQFPN20_DM_V2
code

Pin1 identifier Date code

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 18/60

 TN1433
Device marking for UFQFPN28 (A0B0)

18 Device marking for UFQFPN28 (A0B0)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 17. UFQFPN28 marking example (package top view)

Product
identification(1)

Revision
code

A0B0_UFQFPN28_DM_V3
Y WW Date code

Pin1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 19/60

 TN1433
Device marking for UFQFPN32 (A09E)

19 Device marking for UFQFPN32 (A09E)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 18. UFQFPN32 marking example (package top view)

Product
identification(1)

Y WW Date code

Revision
code

A09E_UFQFPN32_DM_V2
Pin1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 20/60

 TN1433
Device marking for UFQFPN32 (A0B8)

20 Device marking for UFQFPN32 (A0B8)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 19. UFQFPN32 marking example (package top view)

Product
identification(1)

Date code

Y WW Revision code

A0B8_UFQFPN32_DM_V1
Pin1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 21/60

 TN1433
Device marking for UFQFPN48 (A0B9)

21 Device marking for UFQFPN48 (A0B9)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 20. UFQFPN48 marking example (package top view)

Product
identification(1)

Y WW Date code

A0B9_UFQFPN48_DM_V3
Revision
code
Pin1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 22/60

 TN1433
Device marking for VFQFPN36 (ZR)

22 Device marking for VFQFPN36 (ZR)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 21. VFQFPN36 marking example (package top view)

Product
identification(1)

Y WW Date code

Revision

ZR_VFQFPN36_DM_V2
code

Pin1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples
in production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 23/60

 TN1433
Device marking for VFQFPN32 (42)

23 Device marking for VFQFPN32 (42)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 22. VFQFPN32 marking example (package top view)

Product
identification(1)

Y WW Date code

Revision
code

42_VFQFPN32_DM_V1
Pin1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 24/60

 TN1433
Device marking for VFQFPN68 (B029)

24 Device marking for VFQFPN68 (B029)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 23. VFQFPN68 marking example (package top view)

Product
identification(1)

Revision
code

Y WW

B029_VFQFPN68_DM_V4
Date code

Pin1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 25/60

 TN1433
Device marking for LFBGA36 (AL)

25 Device marking for LFBGA36 (AL)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 24. LFBGA36 marking example (package top view)

Product
identification(1)

Y WW Date code

AL_LFBGA36_DM_V1
Revision code

Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 26/60

 TN1433
Device marking for LFBGA100 (H0)

26 Device marking for LFBGA100 (H0)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 25. LFBGA100 marking example (package top view)

Revision
code
Product
identification(1)

Y WW Date code

H0_LFBGA100_DM_V2
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 27/60

 TN1433
Device marking for LFBGA144 (X3)

27 Device marking for LFBGA144 (X3)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 26. LFBGA144 marking example (package top view)

Product
identification(1)

Date code
Revision

X3_LFBGA144_DM_V2
Y WW code

Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples
in production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 28/60

 TN1433
Device marking for LFBGA289 (B0ED)

28 Device marking for LFBGA289 (B0ED)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 27. LFBGA289 marking example (package top view)

Product identification(1)

Revision
code
Date code

B0ED_LFBGA289_DM_V1
Y WW

Ball A1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 29/60

 TN1433
Device marking for LFBGA354 (B02Z)

29 Device marking for LFBGA354 (B02Z)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 28. LFBGA354 marking example (package top view)

Product
identification(1)

Revision code

Date code

B02Z_LFBGA354_DM_V1
Y WW

Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 30/60

 TN1433
Device marking for LFBGA448 (B032)

30 Device marking for LFBGA448 (B032)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 29. LFBGA448 marking example (package top view)

Product
identification(1)

Revision code

Date code

B032_LFBGA448_DM_V1
Y WW

Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 31/60

 TN1433
Device marking for TFBGA64 (R8)

31 Device marking for TFBGA64 (R8)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 30. TFBGA64 marking example (package top view)

Product
identification(1)

Y WW Date code

Revision

R8_TFBGA64_DM_V2
code

Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event will ST be liable for the customer using any of these engineering samples
in production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 32/60

 TN1433
Device marking for TFBGA100 (A08Q)

32 Device marking for TFBGA100 (A08Q)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 31. TFBGA100 marking example (package top view)

Product
identification(1)

Revision
code

Y WW

A08Q_TFBGA100_DM_V3
Date code

Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 33/60

 TN1433
Device marking for TFBGA216 (A0L2)

33 Device marking for TFBGA216 (A0L2)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 32. TFBGA216 marking example (package top view)

Product
identification (1)

Revision code

Date code

Y WW

A0L2_TFBGA216_DM_V1
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 34/60

 TN1433
Device marking for TFBGA225 (B04V)

34 Device marking for TFBGA225 (B04V)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 33. TFBGA225 marking example (package top view)

Product
identification (1)

Revision code

Date code

Y WW

B04V_TFBGA225_DM_V1
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 35/60

 TN1433
Device marking for TFBGA257 (B02Y)

35 Device marking for TFBGA257 (B02Y)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 34. TFBGA257 marking example (package top view)

Product
identification (1)

Revision code

Date code

Y WW

B02Y_TFBGA257_DM_V1
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 36/60

 TN1433
Device marking for TFBGA240+25 (A07U)

36 Device marking for TFBGA240+25 (A07U)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 35. TFBGA240+25 marking example (package top view)

Product
identification(1)

Revision
code

A07U_TFBGA240+25_DM_V2
Y WW

Ball A1 Date code

identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 37/60

 TN1433
Device marking for TFBGA289 (B0EB)

37 Device marking for TFBGA289 (B0EB)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 36. TFBGA289 marking example (package top view)

Product
identification(1)

Revision code

B0EB_TFBGA289_DM_V1
Y WW Date code

Ball A1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 38/60

 TN1433
Device marking for TFBGA320 (B0EC)

38 Device marking for TFBGA320 (B0EC)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 37. TFBGA320 marking example (package top view)

Product
identification(1)

Revision code

B0EC_TFBGA320_DM_V1
Y WW Date code

Ball A1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 39/60

 TN1433
Device marking for TFBGA361 (B031)

39 Device marking for TFBGA361 (B031)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 38. TFBGA361 marking example (package top view)

Product
identification (1)

Revision code

B031_TFBGA361_DM_V1
Y WW Date code

Ball A1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 40/60

 TN1433
Device marking for TFBGA436 (B0D1)

40 Device marking for TFBGA436 (B0D1)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 39. TFBGA436 marking example (package top view)

Product
identification (1)

Revision code

Y WW Date code

B0D1_TFBGA436_DM_V1
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 41/60

 TN1433
Device marking for UFBGA59 (B0FS)

41 Device marking for UFBGA59 (B0FS)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 40. UFBGA59 marking example (package top view)

Product
identification(1)

Date code

Revision
Y WW code

B0FS_UFBGA59_DM_V1
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 42/60

 TN1433
Device marking for UFBGA64 (A019)

42 Device marking for UFBGA64 (A019)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 41. UFBGA64 marking example (package top view)

Product
identification(1)

Y WW Revision code

Date code

A019_UFBGA64_DM_V2
Ball A1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 43/60

 TN1433
Device marking for UFBGA73 (B08E)

43 Device marking for UFBGA73 (B08E)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 42. UFBGA73 marking example (package top view)

Product
identification(1)

Revision
Y WW code

Date code

B08E_UFBGA73_DM_V2
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 44/60

 TN1433
Device marking for UFBGA100 (A0C2)

44 Device marking for UFBGA100 (A0C2)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 43. UFBGA100 marking example (package top view)

Product
identification(1)

Y WW Revision code

Date code

A0C2_UFBGA100_DM_V2
Ball A1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 45/60

 TN1433
Device marking for UFBGA121 (B0CU)

45 Device marking for UFBGA121 (B0CU)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 44. UFBGA121 marking example (package top view)

Product
identification(1)

Revision
Y WW code

Date code

B0CU_UFBGA121_DM_V1
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 46/60

 TN1433
Device marking for UFBGA129 (B09R)

46 Device marking for UFBGA129 (B09R)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 45. UFBGA129 marking example (package top view)

Product
identification(1)

Revision
Y WW code

Date code

B09R_UFBGA129_DM_V3
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 47/60

 TN1433
Device marking for UFBGA132 (A0G8)

47 Device marking for UFBGA132 (A0G8)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 46. UFBGA132 marking example (package top view)

Product
identification(1)

Y WW Revision
code
Date code

A0G8_UFBGA132_DM_V2
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 48/60

 TN1433
Device marking for UFBGA144 (A02Y)

48 Device marking for UFBGA144 (A02Y)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 47. UFBGA144 marking example (package top view)

Product
identification(1)

Revision code

A02Y_UFBGA144_DM_V2
Y WW
Date code
Ball A1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 49/60

 TN1433
Device marking for UFBGA144 (A0AS)

49 Device marking for UFBGA144 (A0AS)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 48. UFBGA144 marking example (package top view)

Product
identification(1)

Y WW Revision code

Date code

A0AS_UFBGA144_DM_V3
Ball A1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 50/60

 TN1433
Device marking for UFBGA169 (A0YV)

50 Device marking for UFBGA169 (A0YV)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at top left.

Figure 49. UFBGA169 marking example (package top view)

Ball A1 identifier

Product
identification(1)

Y WW Revision code

Date code

A0YV_UFBGA169_DM_V4
1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 51/60

 TN1433
Device marking for UFBGA176+25 (A0E7)

51 Device marking for UFBGA176+25 (A0E7)

The following figure gives an example of the locations and orientation of the marking areas versus ball A1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, ball A1 is always located at bottom left.

Figure 50. UFBGA176+25 marking example (package top view)

Revision
code

Product
identification(1)

Y WW Date code

A0E7_UFBGA176+25_DM_V2
Ball A1
identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 52/60

 TN1433
Device marking for SiP-LGA86 (B0CQ)

52 Device marking for SiP-LGA86 (B0CQ)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 51. SiP-LGA86 marking example (package top view)

Product
identification(1)
2D matrix
code

Certification
marking
Revision code
Y WW
Date code

B0CQ_SiP-LGA86_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 53/60

 TN1433
Device marking for SiP-LGA92 (B0HB)

53 Device marking for SiP-LGA92 (B0HB)

The following figure gives an example of the locations and orientation of the marking areas versus pin 1 and
allows engineering samples to be identified.
With the device text markings oriented as shown below, pin 1 is always located at bottom left.

Figure 52. SiP-LGA92 marking example (package top view)

2D matrix
code

Product
identification(1)

Revision code

Y WW
Date code

B0HB_SiP-LGA92_DM_V1
Pin 1 identifier

1. Parts marked as ES or E or accompanied by an Engineering Sample notification letter are not yet qualified
and therefore not approved for use in production. ST is not responsible for any consequences resulting
from such use. In no event is ST liable for the customer using any of these engineering samples in
production. ST's Quality department must be contacted prior to any decision to use these engineering
samples to run a qualification activity.

TN1433 - Rev 1 page 54/60

 TN1433

Revision history
Table 2. Document revision history

Date Version Changes

13-Jan-2023 1 Initial release.

TN1433 - Rev 1 page 55/60

 TN1433
Contents

Contents
1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Device marking for SO8N (O7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 Device marking for TSSOP14 (6R). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 Device marking for TSSOP20 (YA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 Device marking for LQFP32 (5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6 Device marking for LQFP44 (4Y) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7 Device marking for LQFP48 (5B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
8 Device marking for LQFP64 (5W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
9 Device marking for LQFP64 (1R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
10 Device marking for LQFP80 (9X) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
11 Device marking for LQFP80 (1S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
12 Device marking for LQFP100 (1L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
13 Device marking for LQFP128 (TC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
14 Device marking for LQFP144 (1A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
15 Device marking for LQFP176 (1T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
16 Device marking for LQFP208 (UH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
17 Device marking for UFQFPN20 (A0A5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
18 Device marking for UFQFPN28 (A0B0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
19 Device marking for UFQFPN32 (A09E). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
20 Device marking for UFQFPN32 (A0B8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
21 Device marking for UFQFPN48 (A0B9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
22 Device marking for VFQFPN36 (ZR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
23 Device marking for VFQFPN32 (42). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
24 Device marking for VFQFPN68 (B029) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
25 Device marking for LFBGA36 (AL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
26 Device marking for LFBGA100 (H0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
27 Device marking for LFBGA144 (X3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
28 Device marking for LFBGA289 (B0ED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
29 Device marking for LFBGA354 (B02Z) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
30 Device marking for LFBGA448 (B032) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
31 Device marking for TFBGA64 (R8). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
32 Device marking for TFBGA100 (A08Q). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

TN1433 - Rev 1 page 56/60

 TN1433
Contents

33 Device marking for TFBGA216 (A0L2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

34 Device marking for TFBGA225 (B04V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
35 Device marking for TFBGA257 (B02Y) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
36 Device marking for TFBGA240+25 (A07U) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
37 Device marking for TFBGA289 (B0EB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
38 Device marking for TFBGA320 (B0EC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
39 Device marking for TFBGA361 (B031) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
40 Device marking for TFBGA436 (B0D1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
41 Device marking for UFBGA59 (B0FS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
42 Device marking for UFBGA64 (A019) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
43 Device marking for UFBGA73 (B08E). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
44 Device marking for UFBGA100 (A0C2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
45 Device marking for UFBGA121 (B0CU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
46 Device marking for UFBGA129 (B09R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
47 Device marking for UFBGA132 (A0G8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
48 Device marking for UFBGA144 (A02Y). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
49 Device marking for UFBGA144 (A0AS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
50 Device marking for UFBGA169 (A0YV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
51 Device marking for UFBGA176+25 (A0E7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
52 Device marking for SiP-LGA86 (B0CQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
53 Device marking for SiP-LGA92 (B0HB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
List of tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
List of figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

TN1433 - Rev 1 page 57/60

 TN1433
List of tables

List of tables
Table 1. Applicable products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 2. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

TN1433 - Rev 1 page 58/60

 TN1433
List of figures

List of figures
Figure 1. SO8N marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 2. TSSOP14 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 3. TSSOP20 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 4. LQFP32 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 5. LQFP44 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 6. LQFP48 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 7. LQFP64 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 8. LQFP64 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 9. LQFP80 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 10. LQFP80 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 11. LQFP100 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 12. LQFP128 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 13. LQFP144 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 14. LQFP176 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 15. LQFP208 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 16. UFQFPN20 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 17. UFQFPN28 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 18. UFQFPN32 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 19. UFQFPN32 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 20. UFQFPN48 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 21. VFQFPN36 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 22. VFQFPN32 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 23. VFQFPN68 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 24. LFBGA36 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 25. LFBGA100 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 26. LFBGA144 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 27. LFBGA289 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 28. LFBGA354 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 29. LFBGA448 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 30. TFBGA64 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 31. TFBGA100 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 32. TFBGA216 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 33. TFBGA225 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 34. TFBGA257 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 35. TFBGA240+25 marking example (package top view). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 36. TFBGA289 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 37. TFBGA320 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 38. TFBGA361 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 39. TFBGA436 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 40. UFBGA59 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 41. UFBGA64 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 42. UFBGA73 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 43. UFBGA100 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 44. UFBGA121 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 45. UFBGA129 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 46. UFBGA132 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 47. UFBGA144 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 48. UFBGA144 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Figure 49. UFBGA169 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 50. UFBGA176+25 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 51. SiP-LGA86 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 52. SiP-LGA92 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

TN1433 - Rev 1 page 59/60

 TN1433

IMPORTANT NOTICE – READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks. All other product or service names
are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2023 STMicroelectronics – All rights reserved

TN1433 - Rev 1 page 60/60