V 2 Diagram

V2-LCD/LED Screen Panel Repair Guide 147
Bonus-A
LG OLED/LED/LCD TV Interconnect Schematic
Diagrams
32LS3500-Interconnect_2012_Interconnect ………….………..148
37LK450-Interconnect_2011_Interconnect ……………….……151
42CS560-Interconnect_2012_Interconnect ……….……………163
42LG60-Interconnect2_2008_Interconnect …………….………170
42LG60-Interconnect_2008_Interconnect ……………………..172
43LJ5000-Interconnect-Mainboard_2017_Interconnect ……….174
47LV4400-Interconnect_MB Built-In T-con_Interconnect…… 178
49UH6100-Interconnect_2016_Interconnect ……………..……184
55UF7600-Interconnect-Mainboard_2015_Interconnect ……....185
65UH5500-Interconnect-Mainboard_2016-2017_Interconnect…191
T-Con Board Schematic/Circuit

Diagrams
HISENSE RSAG7.820.5129 T-CON Board Schematic……………...…..195
HISENSE RSAG7-820-4159 T-CON Board with LED32K16 TV
HE315DH-B11……………………………………………………..203
SKYWORTH 5800-TCON6-0P10 T-CON Board Schematic…………...208
http://www.LCDRepairGuide.com/screen-repair-v2/
32LS3500 INTERCONNECT DIAGRAM To the Panel’s LED Backlights
J2 LED Block Ground Pulses
Off OUT 1 Pin 3 J2 "LED Driver" to "The Panel"
OUT 4
OUT 3
OUT 2
OUT 1
(1)
PWR_ON Pin 1: Turns on 12V, 24V to the Main and 24V to the LED Driver board. OUT 2 Pin 4
41V
(2)
INV_ON Pin 18: Turns on the Backlights. (Special Note: This set turns on the backlights
180Hz
On
24.44V J2 Pin Label Stby Run Diode Check
OUT 3 Pin 9
with only PWR_ON arriving. INV_ON is not needed). OUT 4 Pin 10 11.76V 1 B+ 0V 41.44V OL
(3) 10.5V p/p
ERROR_OUT Pin 24: Is not used
(4) L201 2 n/c n/c n/c n/c
A_DIM Pin 20: Is not used (Fixed Voltage). Q209 24.51V
100uF
-
C219
100V
(5)
P_DIM Pin 22 can vary according to incoming video IRE level and OSD Backlight setting D201
Warning: Return 24.52V Gnd Q2011 3 OUT 1 0V 1.38V~8.02V OL
+
Output from the Video Processor IC100. Range 0.22V to 3.22V. 24.5V
the Screws when 24.51V
Q210 41.4V
the Shield is 0V 3.56V 4 OUT 2 0V 1.38V~8.02V OL Pins 3,4,9,10
4 3 2 1 OUT 1
106.6V IC102 P202 removed for 10.11V
OUT 2 5-7 n/c n/c n/c n/c
White to Black
C110
220V
35uF
Service if Power 0V
Hot OUT 3
+
393.5V is going to be
Error OUT 4 9 OUT 3 0V 1.38V~8.02V OL
Ground R252 applied. F101
R251 24V
0V Gnd
INV_ON U201 10 OUT 4 0V 1.38V~8.02V OL
D602 Readings 24.56V Q102
3.48V PDIM 5.1V
393.5V
T101 P201 11 n/c n/c n/c n/c P401 to SMPS P201
D601 VCC
Pin Diode Check
12 n/c 0V 41.44V OL
J1 LED Driver 1 OL
C610
450V
68uF
+
J1 "LED Driver" to P202 "SMPS" 2-4 2.68V

D603 Gnd
-
LED BLOCKS (4) LED BAR ON THE LEFT FRONT Pin Label Stby Run Diode Check 5-8
J2 Pin 1 (41V) for LED Blocks 9-12 0.75V
1-5 24V 0V 24.56V OL
OUT 1: Drives the Top LED Block 13-15 Gnd
P201 "SMPS Board" To P401 "MAIN Board" OUT 2: Drives the 2nd from Top LED Block 6-10 Gnd Gnd Gnd Gnd 16 n/c
T501 OUT 3: Drives the 2nd from Bottom LED Block
Main IC501 PIN LABEL STBY RUN Diode 11 ERROR n/c n/c OL 17 2.19V
OUT 4: Drives the Bottom LED Block 18 1.59V
P/N: EAY62512301 24 ERROR 0V 0V OL
LED BLOCK TEST
12 INV_ON 0V 3.41V OL
19 2.19V
23 n/c n/c n/c OL 13 A_DIM n/c n/c OL
IC502 D201 Using a 220Ω resistor one end on Ground 20 OL
IC503 22 P_DIM 0V *0.22V-3.22V OL The other end on any of the OUT lines will turn on the 14 P_DIM 0V *0.22V~3.22V OL 21 2.19V
Hot 3.5V_ST 21 12V 0V 12.15V 1.37V backlight block. (Providing the 41V is present J2 pin 1)
Error and A_DIM are not used. White to Black 22 2.66V
L601
Ground F100 20 A_DIM 0V 0V OL

23 n/c
Cold 24 OL
3.15A/250V 19 12V 0V 12.15V 1.37V For Voltages
LF102 LF101 Hot 18 INV_ON 0V 3.41V OL See P201 SMPS
106.6V
TH101 17 12V 0V 12.15V 1.37V
16 n/c n/c n/c OL Q409 Panel_VCC
P401 EEPROM D S E B Commercial
- + N L 13-15 Gnd Gnd Gnd Gnd Q405 G
C
12V out
Pins 27-30
Remote
INV_CTL IC104 IC1000

BD101 9-12 3.5V (Stby) 3.55V 3.51V 2.63V
C
3 Q407
Q402 2 1 PWR_ON
B E
IC408 Q409 Driver
SK100 5-8 Gnd Gnd Gnd Gnd IC409
3 2
1
2 3
PWR_Det Q401C
E
B P705 LVDS
AC 2-4 24V 0V 24.56V 1.05V 1 +3.3V_Normal
Q403 S G
IC407
+1.5V_DDR
3
2
1
L406
4
SMPS Test P201 Open 1 PWR_ON 0V 3.4V 1.15V To Ft. IR Q400

B
IC402
To Front IR
EL415
C D
2
P201 Note: STBY 3.5V Must be Pin No Load Q403 Driver IC403
1
*0% to 100% +2.5V_Normal

IC1450
present when AC applied. 24 0.0V IC1201
P2401 IC101
23 n/c
A IC5601 +1.10V_VDDC DDR Micro / IC401 USB_OCP
SMPS TEST 1 : Forcing SMPS On. D200
P2401 "MAIN Board" To J1 "IR Board" Video +5V_Normal
Remove AC Power. 22 3.54V C A1
+5V_USB
Jumper Disconnect P401 on Main Board. Pin Label STBY Run Diode Check Processor
21 12.34V AUDIO Mute A2
Jump pin 1 (PWR_ON) to pin 9, 10, 11 or 12 . 20 0V 10 Gnd Gnd Gnd Gnd See LVDS E B
Serial Flash
Q501 X201 IC3703
Apply AC Power. This should force the SMPS to 9 IR 3.52V 3.43V 2.72V waveforms on
C
the on state. All Voltages should be produced.

19 12.34V
Page 3 of IC501 Main 1
2 2
18 3.41V 8 LED_R 2.71V 0V 2.01V 24Mhz

3
TUNER PINS
Test 1 (24V and 12V to Main, 24V to the Backlight LED 7 Gnd Gnd Gnd Gnd Interconnect AUDIO Amp Q802 P/N: EBR75097902 +1.8V_TU 1. n/c
17 12.34V
Driver Board). 41V Backlight Power. Diagram E B 2. Reset
HDMI Hot Swap
Backlights are on. 13-16 Gnd 6 3.5V_ST 3.55V 3.48V 0.75V C Additional p/n: EBR75097911 3. SCL
5 KEY 2 3.54V 3.47V OL L504 L506 E B
A1 A2 4. SDA
Disconnect AC Power. 9-12 3.54V Q801 C C D821 5.+3.3V_TU
A1 A2
5-8 Gnd 4 KEY 1 3.54V 3.47V OL 6. SIF
C
DDC_SCL/SDA Pull Up No backside components 7. +1.8V_TU
2-4 24.35V 3 Gnd Gnd Gnd Gnd L503 L505 D822 8. CVBS
1 3.54V 2 Sensor_SDA 0.32V 3.36V 1.18V 9. IF AGC
To all Speakers TU3700 10. DIF (P)
1
1 Sensor_SCL 0.32V 3.36V 1.18V 11. DIF (N)
Key 1 Line J1 or P2401 pin 4 All pins 12.31V 1
Diode Test = 2.72V

Resistance Voltage 12V Pins 27 ~ 30 and JK801 JK802
Volume (+) 17.96M Ω Volume (+) 1.75V P501 HDMI 1 HDMI 2
Volume (-) 11.87M Ω Volume (-) 1.17V
LVDS Video Signals
To SPK Component / Composite 1 JK1001
RS232
Front IR / Key Board Settings 6M Ω Menu 0.6V
OK 0.99M Ω Enter 0.1V J2 LVDS TDSS-H101F
Intelligent Sensor Key 2 Line J1 or P2401 pin 5
J1
Resistance Voltage
Interface See DC Voltages for Main Board on
CH (Up) 17.96M Ω CH (Up) 1.75V Page 3 of Interconnect Diagram
CH (Dn) 11.87M Ω CH (Dn) 1.17V J1 LVDS
Power 6M Ω Power 0.6V
A Input 0.99M Ω Input 0.1V To the Panel
Key 1 or 2, No Key Pressed, resistance: Open ( Voltage 3.47V)
32LS3500 Main Board Component Voltages
IC104 Micro IC403 +1.10V_VDDC IC408 Power_Det IC1000 RS232 Data IC1450 5V Short Protection
Pin EEPROM Pin Regulator Pin 12V Pin Buffer Pin for USB
[1] 0V (Gnd) [1] 3.4V (In) +3.3V_ST [1] 0V (Gnd) [1] 3.34V (C1+) [1] 0V (Gnd)
[2] 0V (Gnd) [2] 3.4V (In) +3.3V_ST [2] 3.6825V (Reset) [2] 8.8V (V+) [2] 5.24V (In1)
[3] 0V (Gnd) [3] Do not Measure [3] 3.67V (In) +12V [3] 3.25V (C1-) [3] 5.24V (In2)
[4] 0V (Gnd) [4] 0V (Gnd) [4] 3.34V (C2+) [4] 3.39V (USB1_CTL)
[[5]] 3.4V (SDA)
( ) [[5]] 0V (Gnd)
( ) IC409 Power_Det
_ [[5]] V ((V+)) [[5]] 5.19V ((FLG))
[6] 3.4V (SCL) [6] Do not Measure Pin 24V [6] (-5.7V ) (C2-) [6] 5.24V (Out1)
[7] 0V (Gnd) [7] Do not Measure [1] 0V (Gnd) [7] 0V (n/c) [7] 5.24V (Out2)
[8] 3.4V (B+) [8] Do not Measure [2] 3.58V (Reset) [8] 3.34V (n/c) [8] 0V (n/c)
[9] 2.16V [3] 3.81V (In) +24V [9] 3.36V (n/c)
IC401 +5V_Normal [10] 1.23V (Out) [10] 5.79V (n/c) IC5601 Serial
Pin +5V_USB [11] 1.23V (Out) IC3703 +1.8V_TU [11] 0V (DN1) Pin Flash Memory
[1] 0V (Gnd) [12] 1.23V (Out) Pin Regulator [12] 0.04V (ROut1) [1] 3.34V (Hold)
[2] 12.0V (In) [13] 4.61V (BOOT) [1] 0V (Gnd) [13] 0V (RIn1) [2] 3.33V (In) +3.3V_ST
[3] 0V (Gnd) [14] 0V (n/c) [2] 1.80V (Reset) [14] (-5.73V ) (DOut1) [3] 0V (n/c)
[4] 0.8V (FB) [15] 3.24V (EN) 3.3V_Normal [3] 3.39V (In) [15] 0V (Gnd) [4] 0V (n/c)
[5] 0.95V (COMP) [16] 3.48V (In) +3.3V_ST [16] 3.33V (In) +3.3V_ST [5] 0V (n/c)
[6] 12.0V (EN) [6] 0V (n/c)
[7] 2.07V (SS) IC407 (+1.5V_DDR) [7] 1.34V (/SPI_CS)
[8] 0V (n/c) Pin Regulator [8] 1.15V (SPI_SDO)
For Output, use L406 [1] 3.47V (In) +3.3V_ST [9] 0V (WP)
[2] 0V (n/c) [10] 0V (n/c)
IC402 +2.5V_Normal
+2 5V Normal [3] 3.47V +3.3V_ST
3 47V (In) +3 3V ST [11] 0V (n/c)
Pin Regulator [4] 3.4V (EN) +3.3V_Normal [12] 0V (n/c)
[1] 0V (Gnd) [5] 0V (Gnd) [13] 0V (n/c)
[2] 2.5V (Out) [6] 3.36V (SS) [14] 0V (n/c)
[3] 3.4V (In) [7] 0.8V (FB) [15] 0V (SPI_SDI)
[8] 1.54V (Out) [16] 0V (SPI_SCK)
Q400 +3.3V_Normal Q403 +3.3V_Normal Q409 PANEL_VCC Q501 Audio Mute D200 SOC_Reset
Pin Driver for Q403 Pin Switch Pin Switch Pin Inputs to pin 14 IC501 Pin Speed Up
B 0.63V (POWER_ON/OFF_1) S 3.48V (In) +3.3V_ST S 12.0V (In) +12V B 0.02V (Mute_Ctl) [C] 0V
C 0.05V (Ctrl) G 0.07V (Enable) G 1.79V (Enable) C 3.42V (Mute to IC501) [A] 0V
E 0V (Gnd) D 3.41V (Out) +3.3V_Normal D 11.99V (Out) E Gnd [A-C] 0V (Gnd)
Q401 Power On/Off Q405 Inverter On/Off Q801 HDMI 2 D821 DDC_SCL1/SDA1
Pin Driver for Q402 Pin Switch Pin Hot Swap Pin Pull Up
B 0.66V (RL_ON) B 0.02V (INV_CTL) B 0.66V (HPD2) [A1] V (5V_HDMI_1)
C 0.06V (Ctrl) to Q402 C 3.4V (INV_On) C 0.04V (HDMI HS) [A2] 5.32V (+5V_Normal)
E Gnd E 0V (Gnd) E Gnd [C] 5.14V (Pull_Up)
Q402 Power On/Off Q407 PANEL_VCC Q802 HDMI 1 D822 DDC_SCL2/SDA2

Pin Switch Pin Drives Q409 Pin Hot Swap Pin Pull Up
1 3.4V (In) +3.3V_ST B 0.65V (Pannel_Ctl) B 0.66V (HPD1) [A1] 5.32V (5V_HDMI_1)
2 3.35V (Ctrl) from Q401 C 0.53V (EN) to Q409 C 0.04V (HDMI HS) [A2] 5.32V (+5V_Normal)
3 3.39V (Out) PWR_ON E Gnd E Gnd [C] 5.14V (Pull_Up)
32LS3500 LVDS P705 WAVEFORMS
P705 Pin 6 Main or J2 Interface P705 Pin 7 Main or J2 Interface P705 Pin 9 Main or J2 Interface P705 Pin 10 Main or J2 Interface
Clock (RX~CK-)
2uSec per/div 360mV p/p 2uSec per/div 412mV p/p 2uSec per/div 444mV p/p 2uSec per/div 392mV p/p
P705 Pin 12 Main or J2 Interface P705 Pin 13 Main or J2 Interface P705 Pin 15 Main or J2 Interface P705 Pin 16 Main or J2 Interface
Clock (RX~CK-)
2uSec per/div 420mV p/p 2uSec per/div 456mV p/p 2uSec per/div 460mV p/p 2uSec per/div 392mV p/p
P705 Pin 18 Main or J2 Interface P705 Pin 19 Main or J2 Interface
LVDS CABLE WAVEFORMS:

Waveforms taken using SMTP Color Bar input.
All readings give the Scale 100mV and 2uSec per division Time Base related to scope settings.
2uSec per/div 460mV p/p 2uSec per/div 460mV p/p

32LS3500 Main Board +3.5V_ST Distribution
+3.5V_ST Input: Pins 9, 10, 11, 12
Q402 Not On in STBY

Turned on by +3.3V_Normal IC1000
3
L404 1 Q402 PWR_ON Commercial
2
Remote
L420 IC407 Not On in STBY
To Front Q403 IC407
Turned on by +3.3V_Normal
IR / Keyboard +3.3V_Normal S G +1.5V_DDR
D Q403 Not On in STBY Turned on by
+3.5V_ST L2403 L413 POWER_ON/OFF_1
Output: Pin 6
Key 2 Pin 5 IC403 IC101 L206
L2401 R2404
Key 1 Pin 4 L2402 R2405 +1.10V_VDDC Micro AVDD_NODIE
IC403 Not On in STBY Video R143
S/T_SCL
Turned on by +3.3V_Normal Processor R149
Mute C200 S/T_SDA
E B IC5601 Serial Flash
C C200 is SOC_Reset X201
AUDIO Mute 24Mhz

For IC403, IC407, Q403 Voltage Distribution
To IC501 see “Other Voltage Distributions” X201 Runs in Standby
Pin 14
LG TRAINING
CENTER Page 4 of Interconnect Diagram October 2012 32LS3500 LCD TV
32LS3500 Main Board +12V Distribution PWR_ON Q402: Turned on by Q401 turned on by IC101 RL_ON.
Output pin 1 to SMPS. Turns on 12V and 20V.
Input: Pins 17,19,21 +12V (For power to Q402, see +3.5V_ST Voltage Distribution) Panel_VCC
To T-CON
L412 R439
12V out Pins 48-51
Q409 R440
P401 Panel_VCC S P703 LVDS
E B
D G C
Panel_CTL
PWR_ON Panel_VCC Q407 R430
L402 +3.5V_ST
3
Q402 Q409 Ctrl. RL_ON
1 3
1 2
E Gnd R401
2 R406 C B RL_ON
USB
IC408 R448 Q401 Note: Q409 turned on by
PWR_Det Q402 Ctrl. PANEL_CTL from IC101 via Q407 +5V_USB 4
L406
1
+5V_Normal
L425
IC101 To pin 1
L401
Micro L1451 USB
Video +5V_Normal IC401 IC1450
+5V_Normal USB_OCP
Processor
+5V_USB
X201
24Mhz
DDC_SCL1/SDA1 Pull Up
D821
A1 A2
C
A1 A2
DDC_SCL2/SDA2 Pull Up D822 C
LG TRAINING
32LS3500 Main Board +24V Distribution
NOTE: 24V is the label, but the Voltage is actually 24.56V
+24V PWR_ON:Q402: Turned on by Q401 turned on by IC101 RL_ON.

(For power to Q402, see +3.5V_ST Voltage Distribution)
Input: Pins 2 ~ 4
P401
PWR_Det PWR_ON
L407 +3.5V_ST
3
Q402
2
1
E Gnd
RL_ON
2 R406 C B
R401
3 Q401
1
Q402 Ctrl.
R482
AUDIO Amp
L501
IC501
22 +24V_AMP
23
24 37 38 39
L504 L506
L503 L505
P501
LG TRAINING
32LS3500 Main Board Other Voltage Distributions
After all voltages are +3.5V_ST Input: Pins 9, 10, 11, 12
turned on on the Main
board, Q405 is turned Q405 turns on
Off supplying INV_ON backlights
P401 EEPROM IC104
to the power supply (via
INV_CTL
pin 18) turning on the From Q403
C
backlights. Collector
pulled up by Q405 B E 18 IC407 Turned on by +3.3V_Normal
L404 +3.3V_Normal
+3.3V_Normal through
INV_CTL
R419 R419 L420 IC407 L1209
+1.5V_DDR AVDD_MIU
Q400 3 2 1 See +3.5V_ST Voltage Distribution
B C S
G
Q403 L1202 Primary distribution of +3.5V_ST
D
R433 IC402
E
AVDD_DRO 2
R428
+3.3V_Normal
IC1201 IC101 +2.5V_Normal
IC403 L415 DDR Micro
IC403 Turned +1.10V_VDDC Video
Q403 Turned on Processor
on by
by Q400 MIUVDDC
POWER_ON/
+3.3V_Normal
L228
OFF_1 IC3703
1
2 2
3
AUDIO Amp IC101

L208 R206
IC501 L502 AVDD_AU33 MODEL_OPT_3 +1.8V_TU
R4027
L204 MODEL_OPT_4
VDD_33 R4028
MODEL_OPT_5 TUNER PINS
R182 L211
URSA5_RESET 1. n/c
R226 AVDD2P5 2. Reset
MODEL_OPT_0
R211 L229 3. SCL
MODEL_OPT_1 AVDD2P5_MOD 4. SDA
R208
L219 TU3700 5.+3.3V_TU
MODEL_OPT_2
L227 R4019 AVDD25_PGA 11
6. SIF
IF_AGC_MAIN
R161 7. +1.8V_TU
Sensor_SDA
8. CVBS
R160 Sensor_SCL +3.3V_TU 9. IF AGC
R1660 L3703 1 10. DIF (P)
AV_CVBS_DET 11. DIF (N)
R1612 +3.3V_Normal
COMP2_DET
R141 From Q403
AMP_SDA
R140
AMP_SCL
R145
I2C_SDA
R144
I2C_SCL
LG TRAINING
37LK450 INTERCONNECT DIAGRAM VCC 3.3V pins 52, 53
VDD 16V pins 35,36,37
VCC 3.3V pins 8, 9
VDD 16V pins 24, 25, 26
VGL -6V pin 50 VGL -6V pin 11
Other U601 Voltages to the Panel
SMPS TEST 1 : Forcing SMPS On. Remove AC Power. VGHC 23.33V pins 47, 48 VGHC 23.33V pins 13, 14 1) [15.44V] J103 41 & J105 20 17) [VCC 3.3V] J103 8,9 & J105 52,53
Disconnect P401 on Main Board. Jump pin 1 (PWR_ON) to pin 9, 10, 11 or 12 . TO TFT MODULE TO TFT MODULE 2) [15.25V] J103 40 & J105 21 18) [6.7V] J103 35 & J105 27
Apply AC Power. This should force the SMPS to the on state. All Voltages should be produced. 3) [13V] J103 39 & J105 22 19) [6.34V] J103 36 & J105 28
J105 J103
(24V and 12V to Main). Also 24V to the Ballast. However the Backlights are not on. 4) [11.27V] J103 38 & J105 23 20) [5.62V] J103 33 & J105 29 For best approach to jump 3.3V to pin 44.
Q101 5) [10.22V] J103 37 & J105 24 21) [1.23V] J103 38 & J105 30
Disconnect AC Power. Gnd 3.3V
Gnd
0V 6) [9.4V] J103 36 & J105 25 22) [3V] J103 30 & J105 31
Use jumper with needles on each end.
SMPS TEST 2 : Forcing Backlights On. U402
L202 U202
1) 1.2V
2) Gnd Test
Gnd 0V
Q100
7) [7.47V] J103 35 & J105 26 28) [7.18V] J103 16 & J105 45 Attach 44 first, apply power, then touch
Leave Jumper from Test 1 in place. Note: STBY 3.5V StaticHi 17.9V
Jump pin 18 (INV_ON) to pin 9, 10, 11 or 12.
VCC 3.3V 1 2 3 3) 3.3V 3.3V 8) [16V] J103 24,25,26 & J105 35,36,37 29) [7.18V] J103 16 & J105 45 left side of L202. Then observe screen.
Must be present U205 U100
Q201 3.33V Gnd 2
D401
Apply AC Power. This should force the Backlights to come on. when AC applied. 7.9V 16 D102
16V V D202 U400 VCC U601
V3D3 3.3V
SMPS P201 Front pins on SMPS P201 Front pins on
D203 VDD 16V P201 "SMPS Board" To P401 "MAIN Board" P401 to SMPS P201
TEST 1
connector are connector are U201
Warning: Over 23 24 odd Pins. TEST 2 23 24 odd Pins. Gnd
D201 -3V VGL VGHC 23.33V Pin Label STBY Run No Load Diode Check Pin Diode
D101
D105
D108
D107
D100
2.9Kv -6.1V
7 6 12V 21 22 12V 21 22
12V
D106 24 ERROR 0V 0V 0V OL 1 2.9V
To each Backlight Q505 16V VGL -6V (1) PWR-On Pin 1: Turns on 12V, 24V to the Main and
12V 19 20 12V 19 20 F101 2-4 2.37V 24V to the Inverter. (Backlights not on).
INV_ON 23 n/c n/c n/c n/c OL
12V 12V U101
To Backlight T10 U1 12V 17 18 12V 17 18
Gn J102 Gn 22 P-DIM 0.02V 0.46V~3.2V 0V OL 5-8 Gnd
15 16 15 16 12V L201 12V d d (2) INV-On Pin 18: Turns on the Backlights
B 1 44 51
12V In 21 12V 0.06V 12.23V 12.18V 2.09V 9-12 1.15V
13 14 13 14
1 5 D201 Pins 48~51 20 A-DIM 0.02V 3.31V 0V OL 13-16 Gnd
(3) Error_Out Pin 24: Goes high when the backlights are
5 1 Q201 3.5V_ST 11 12 3.5V_ST 11 12 told to come on. Goes back low when they come on.
Q311
3.5V_ST 3.5V_ST To Main 19 12V 0.06V 12.23V 12.18V 2.09V 17 2.3V If it goes high again on the 5th attempt to fire the
9 10 9 10
T9 18 INV_On/Off 0.52V 3.09V 0V OL 18 OL backlights, the set shuts off.
To Backlight Q801
7 8 7 8
A 5 6 A 5 6 LVDS 17 12V 0.06V 12.23V 12.18V 2.09V 19 2.3V (4) A-DIM Pin 20: Is not used. It is a fixed Voltage.
6 7
DU59 DU64 24V 3 4 24V 24V 3 4 24V 13~16 Gnd Gnd Gnd Gnd Gnd 20 OL
DU61 (5) P-DIM Pin 22 Will vary according to OSD Backlight
DU15 DU63 1 2 24V 1 2 24V 9~12 3.5V_STBY 3.53V 3.5V 3.53V 2.62V 21 2.3V
DU58 DU62 PWR_ON PWR_ON 12V Pins 48 ~ 51 and setting, incoming video IRE level and Ambient room light
DU57 5~8 Gnd Gnd Gnd Gnd Gnd 22 OL
To Backlight 6 CN1
5
Hot Gnd
(Shock Hazard)
LVDS Video Signals
2~4 24V 0.05V 24.17V 24.36V 1.27V 23 Gnd
conditions. It is output from the Video Processor.
Range 0.46V to 3.2V.
T8 1 PWER_ON 0V 3.38V 3.53V 1.16V 24 OL

7 1 For LVDS Video Signals see For Voltages
8A F1
5
125V 24V SMPS Page 2 of Interconnect Diagram For Main Component Voltages see See P201 SMPS
T7 Page 3 of Interconnect Diagram
To Backlight 1 270uF + - P/N: EAY62170001 Q402 RL_ON Switch
DU14
35V
12V Source
DU56
Q702
IC408/IC409 Power Det
DU13 C164
D254 PANEL TEST: To run the T-CON without the Main board. IC401 12V in
DU55 Q103 D252 Q401 IC408
7 6 +- (Set up SMPS in Test 2 mode). P401
3
Q405 Q4023 2 1 5V_USB

With no power applied to the SMPS, disconnect LVDS 3.5V_ST in
270uF P202 D201 P201 Q406
HDCP
INV On/Off Switch
2 1
IC409 L406
To Backlight
T6
35V
C163 24V Source Cable J102. 1.5V_DDR EEPROM 3 21
T102 Q407 USB
3.5V Source Jump 12V from the SMPS (P201 pins 17 or 19) to F101 IC407 IC103 5V_Normal IC406
Q107 fuse on the T-CON.
G S
Panel Vcc 12V in
1 5 Q409 L422
1 5 D251 Switch
Jump 3.3V from the VCC Test point (Left side of L202) to
D
IC1450
IC501
IC502
IC403 IC405 L421
pin 44 of J102. Apply AC power to the SMPS. L423 USB 5V
To Backlight
T5 Q107 The T-CON will product patters on the screen, Red, Green, 1.26V_DDR IC1202 DDR 3.3V_Normal Current Sense
Cold
T501 Blue, etc. 3.5V_ST in 12V in
5V_USB in
7 6 Hot IC104 EEPROM MAIN BOARD
IC102 Q102 Saturn p/n: EBT61525901 CUSDLH
Gnd
DU54 Other SMPS: P202 "SMPS Board" To CN1 "Ballast Board" L415
Ballast 37LK450-
p/n: EBT61542101 CUSDLH
NAND IC3703
UB.SUSYJK/ Pin Label STBY Run Diode Check P703 IC102
FLASH
2
To Backlight Q101 DDR
6 0.46V~3.2V
T4
5
Q104
CUSYLH
p/n: EAY60869307
14 EPWM 0V OL
P1001 IC1201 IC101 Saturn 3 2 1
D602 13 IPWM 0.02V 3.31V OL
7 1 For Voltages Video Q408 1.8V_TU
6 F601 12 INV_On/Off 0V 3.09V OL Debug G
5 Processor
D
See Table for P2401

S
3.15A/250V STBY: 163V 3.3V_TU in

T3 11 DET 0V 0V OL Q1001 IC1401
1
Q704 J1 "IR Board" To P2401 RUN: 387V IC402 2.5V_Normal
7
Gnd
To Backlight 6~10 Gnd Gnd Gnd Gnd Serial Flash
DU53 Pin Diode Check Q602 3
3.5V_Normal in EIDID HDMI Side
450V
2 2
L601
68uF
DU12 1 X1002
+
Q701 +- OL 1~5 24V 0.05V 24.17V 1.27V IC1002 D

Q806 G B
S Note: Components in Grey are on the 1
IC804 JK803
32.768KHz back and are flipped for from view.
2 OL HDMI 3
-
7 Pin 14 is P_DIM, Pin 13 is A_DIM, Pin 11 is Error. Micro DS

6 Other Main Boards Used in the 37LK450
Q105 C162 3 Gnd Q602 EEPROM D804
4 12V Pins 1 ~ 4 and D825
GB
X201 p/n: EBU61376604 CUSYLH/SUSYJK
450V
68uF
OL Q805 D824
+
Q101 IC1001 p/n: EBT61542109 CUSYLH/SUSYJK

To Backlight +- 5 OL LVDS Video Signals
T2 -
Q2405 IR Q803
6 OL F101 AC 24MHz Q1105 Q1101
Q2406 Buffers JK1103 JK1102
1 5 C161 7 Gnd 5A/250V Protection Q1104
1 5 Q703 8 OL A P2401 Q1102
9 0.93V JK1601 JK1603 Q1103
Q106 P2401 “Main” to J1 “Ft. IR/SoftTouch Key Board”
T1 DU52 10 Gnd L
BD101
To Backlight 18. IF p
JK3301 HP
11 Pin Label STBY Run Diode Check Digital Video
Q102 OL G 17. IF n
DU51 JK1104 (PC) TU3702 16. IF AGC
7 6 12 OL N 15 SDA 3.53V 3.29V 1.97V Q501 TUNER
15. Reset
Q1106
RGB EDID JK1604 14. 3.3V
13 Gnd 14 SCL 3.52V 3.29V 1.97V TDVJ-H101F 13. 1.26V
AC 12. GND
DU11 14 OL SK101 In 13 Gnd Gnd Gnd Gnd IC501 IC1105 Analog
11. CVBS
SIDE A/V
Q3703
Video
D1115 10. NC
12 LED_R 0V 0V 2.67V Audio Amp 3.3V_Normal
JK1101 (RS232)
Audio 9. SIF
For Ballast Component Voltages and drive +3.3V_NORMAL 0.56V 3.08V 0.56V in IC1101 8. NC
Q3705
11 L509 L508
L507 L506 IC404 Tuner Data 7. SDA
waveforms see Key 1 & Key 2 Voltage and Resistance Chart with buttons pressed. 10 Gnd Gnd Gnd Gnd Tuner Clock 6. SCL
1 2 3
1.8V_AMP 5. NC
Page 4 of Interconnect Diagram Key 1 J1/P2401 Pin 3 Key 2 J1/P2401 Pin 4 9 IR 1.96V 1.93V OL RS232 Data
4. NC
D822 Q802 IC801

Tuner B+ 3. 5V
Resistance Function Voltage Resistance Function 8 LED_B 0V 0V 2.67V P501 2

Q801
IC802
Voltage EIDID HDMI 1 2. NC
1. NC
1.96MΩ Vol + 1.69V 1.96MΩ CH + 1.69V 7 Gnd Gnd Gnd Gnd
J1 1.24MΩ Vol - 1.14V 1.24MΩ CH - 1.14V 6 3.5V_ST 3.33V 3.49V 1.16V R-R+L-L+ EIDID HDMI 2 JK801D821
Front IR 550KΩ
11.5Ω
Menu 0.53V 550KΩ Power 0.53V 5 KEY 2 3.3V 3.29V 1.83V
JK802
Enter 0.0V 11.5Ω Input 0.0V To all Speakers
4 KEY 1 3.3V 3.29V 1.83V
All pins 12.05V
A Voltage and Resistance taken with AC applied to the set. 3 Gnd Gnd Gnd Gnd
No Button pressed Resistance is 16.7MΩ Diode Test = OL
2 NEC_EEPROM SDA 3.13V 3.48V 3.29V
1 NEC_EEPROM SCL 2.12V 3.48V 3.29V
37LK450 MAIN (FRONT SIDE) SIMICONDUCTORS
IC103 HDCP IC403 (+1.26V_VDDC) IC406 (+5V_Normal) Q408 (+1.5V_FRC_DDR) Q1001 EDID Write D804 Source Bias
Pin EEPROM Pin Regulator Pin Regulator Pin Switch Pin Protect Pin Q806
[1] 0V (Gnd) [1] 3.28V (In) [1] 0V (Gnd) G 3.3V (PWR On/Off2_1) B 0V [A1] 0V
[2] 0V (Gnd) [2] 3.28V (In) [2] 12.23V (In) S 1.51V (In) C 4.7V [A2] 3.27V
[3] 3.29V (B+) [3] 0V (Gnd) [3] 0V (Gnd) D 1.52V (Out) E Gnd [C] 3.17V
[4] 0V (Gnd) [4] 0V (Gnd) [4] 0.8V
[5] 0V [5] 0V (Gnd) [5] 0.86V Q801 HDMI 2 Q1105 Head Phone D822 5V Routing
[6] 3.29V [6] 0.8V [6] 3.32V (PWR On/Off1) Pin Hot Swap Pin MUTE Pin for IC802
[7] 0V (Gnd) [7] 0.86V [7] 5V (Out) B 0.63V B 2.82V [A1] 5V
[8] 3.29V (B+) [8] 0.54V [8] 5V (Out) C 0V C 0V [A2] 0V
[9] 1.75V E Gnd E 3.34V [C] 4.7V
IC401 5V Regulator [10] 1.33V (Out) IC407 (+1.5V_DDR)
Pin for USB [11] 1.33V (Out) Pin Regulator Q802 HDMI 1 Q1106 Head Phone D825 Source Bias
[1] 0V (Gnd) [12] 1.33V (Out) [1] 3.32V (In) Pin Hot Swap Pin Mute Driver Pin Q805
[2] 12.24V (In) [13] 4.72V [2] 3.32V (In) B 0.63V B 0V [A1] 0V
[3] 0V (Gnd) [14] n/c [3] 0V (Gnd) C 0V C 2.82V [A2] 0.06V
[4] 0.8V [15] 3.29V [4] 0V (Gnd) E Gnd E Gnd [C] 3.17V
[5] 0.8V [16] 3.28V (In) [5] 0V (Gnd)
[6] 3.3V (PWR On/Off2_1) [6] 0.83V Q805 CEC Remote
[7] 4 99V (O
4.99V (Out)
t) IC405 (+3.3V_NORMAL)
(+3 3V NORMAL) [7] 0 7V
0.7V Pin
Pi HDMI CEC
[8] 4.99V (Out) Pin Regulator [8] 0.51V [B] 3.17V
[1] 0V (Gnd) [9] 1.93V [G] 0V
IC402 (+2.5V_Normal) [2] 12.23V (In) [10] 1.52V (Out) [S] 0V
Pin Regulator [3] 0V (Gnd) [11] 1.52V (Out) [D] 0.06VV
[1] 3.29V (In) [4] 0.8V [12] 1.52V (Out)
[2] 0V (Gnd) [5] 0.87V [13] 4.87V Q806 CEC Remote
[3] 2.5V (Out) [6] 3.32V (PWR On/Off1) [14] n/c Pin HDMI CEC
[7] 3.34V (Out) [15] 3.31V [B] 3.17V
[8] 3.34V (Out) [16] 3.32V (In) [G] 0V
[S] 3.28V
[D] 3.29V
37LK450 MAIN (BACK SIDE) SIMICONDUCTORS
IC104 Microprocessor IC804 EDID Data IC1105 EDID Data Q401 Power On/Off Q803 HDMI 4 D821 5V Routing
Pin EEPROM Pin HDMI4 Pin PC Pin Driver for Q402 Pin Hot Swap Pin for IC801
[1] 0V (n/c) [1] 0V (Gnd) [1] 0V (Gnd) B 0.65V (RL_ON) B 0.65V [A1] 0V
[2] 0V (Gnd) [2] 0V (Gnd) [2] 0V (Gnd) C 0V C 0V [A2] 5.0V
[3] 0V (Gnd) [3] 0V (Gnd) [3] 0V (Gnd) E Gnd E Gnd [C] 4.7V
[4] 0V (Gnd) [4] 0V (Gnd) [4] 0V (Gnd)
[5] 3.29V (SDA) [5] 4.7V (SDA) [5] 4.7V (SDA) Q402 Power On/Off Q1101 Head Phone D824 5V Routing
[6] 3.29V (SCL) [6] 4.7V (SCL) [6] 4.7V (SCL) Pin Switch Pin MUTE Pin for IC804
[7] 0V (G
(Gnd)
d) [7] 4 7V (WP)
4.7V [7] 4 7V (WP)
4.7V 133.3V
3V (In)
(I ) B 0V [A1] 0V
[8] 3.29V (B+) [8] 4.7V (Vcc) [8] 4.7V (Vcc) 2 0.8V (Ctl) C 0V [A2] 5V
3 3.16V (Out) E Gnd [C] 4.7V
IC404 (+1.8V_Amp) IC1001 Micro IC1401 Serial Flash
Pin Regulator Pin EEPROM Pin Memory Q405 Inverter On/Off Q1102 Head Phone D1115 5V Routing
[1] Gnd [1] 0V (Gnd) [1] 0.0V Pin Switch Pin MUTE Pin for IC1105
[2] 1.79V (Out) [2] 0V (Gnd) [2] 3.3V B 0.0V B 0V [A1] 0.0V
[3] 3.29V (In) [3] 3.3V (B+) [3] 3.3V C 3.0V (INV_On) C 0V [A2] 5V
[4] 0V (Gnd) [4] 0V (Gnd) E Gnd E Gnd [C] 4.7V
IC408 Power_Det [5] 3.3V (SDA) [5] 0V
Pin 12V [6] 3.3V (SCL) [6] 0V Q406 PANEL_VCC Q1103 Head Phone Q2405 IR
[1] 0V (Gnd) [7] 0V (Gnd) [7] 3.3V (B+) Pin Control 1st Driver Pin MUTE Pin Buffer
[2] 3.30V (Reset) [8] 3.3V (B+) [8] 3.3V (B+) B 0.0V B 0V B 0.0V
[3] 3.33V (In) C 0.68V C 0V C 3.0V (INV_On)
IC1101 RS232 IC1450 5V Short Protection E Gnd E Gnd E Gnd
IC409 Power_Det Pin Data Buffer Pin for USB
Pin 24V [1] 3.3V [1] 0V (Gnd) Q407 PANEL_VCC Q1104 Head Phone Q2406 IR
[1] 0V (Gnd) [2] 5.4V [2] 4.98V (In) Pin Control 2nd Driver Pin MUTE Pin Buffer
[2] 3.30V (Reset) [3] 0V [3] 4.98V (In) B 0.68V B 0V B 0.0V
[3] 3.33V (In) [4] 0V [4] 3.3V (USB-En) C 0V C 0V C 0.68V
[5] (-5.4V) [5] 4.96V E Gnd E Gnd E Gnd
IC801 EDID Data [6] 0V [6] 4.98V (Out)
Pin HDMI1 [7] n/c (0V) [7] 4.98V (Out) Q409 PANEL_VCC Q3703 Tuner CVSB
[1] 0V (G
(Gnd)
d) [8] n/c
/ (0V) [8] n/c
/ (0V) Pin
Pi S it h
Switch Pin
Pi (Video)) B
(Vid Buffer
ff
[2] 0V (Gnd) [9] n/c (3.3V) S 12.2V (In) B 3.4V
[3] 0V (Gnd) [10] n/c (0V) IC3703 (+1.2V_TU) G 1.84V (Enable) C Gnd
[4] 0V (Gnd) [11] n/c (3.3V) Pin Regulator D 12.2V (Out) E 4.1V
[5] 4.7V (SDA) [12] 3.3V [1] 0V (Gnd)
[6] 4.7V (SCL) [13] 0V [2] 1.26V (Out) Q501 AMP_MUTE Q3705 Tuner SIF
[7] 4.7V (WP) [14] (-5.4V) [3] 3.3V (In) Pin Pin 25 IC600 Pin (Sound) Buffer
[8] 4.7V (Vcc) [15] 0V (Gnd) B 0.0V B 0.2V
[16] 3.3V C 3.35V C Gnd
IC802 EDID Data E Gnd E 0.9V
Pin HDMI2
[1] 0V (Gnd)
[2] 0V (Gnd)
[3] 0V (Gnd)
[4] 0V (Gnd)
[5] 4.7V (SDA)
[6] 4.7V (SCL)
[7] 4.7V (WP)
[8] 4.7V (Vcc)
37LK450 LVDS P703 WAVEFORMS
P703 Pin 11 Main or CN1 Pin 41 T-CON P703 Pin 13 or CN1 Pin 39 T-CON P703 Pin 16 or CN1 Pin 36 and P703 Pin 19 or CN1 Pin 33 T-CON P703 Pin 21 or CN1 Pin 31 T-CON
P703 Pin 32 or CN1 20 T-CON
Clock (RX~CK-)
2uSec per/div 611mV p/p 2uSec per/div 664mV p/p 2uSec per/div 638mV p/p 2uSec per/div 654mV p/p 2uSec per/div 716mV p/p
P703 Pin 12 or CN1 Pin 40 T-CON P703 Pin 14 or CN1 Pin 38 T-CON P703 Pin 20 or CN1 Pin 32 T-CON P703 Pin 22 or CN1 Pin 30 T-CON
P703 Pin 17 or CN1 Pin 33 and
P703 Pin 33 or CN1 19 T-CON
Clock (RX~CK+)
P703 Pin 23 or CN1 Pin 29 T-CON P703 Pin 27 or CN1 Pin 24 T-CON P703 Pin 29 or CN1 Pin 22 T-CON P703 Pin 35 or CN1 Pin 17 T-CON P703 Pin 37 or CN1 Pin 15 T-CON
P703 Pin 24 or CN1 Pin 28 T-CON P703 Pin 28 or CN1 Pin 23 T-CON P703 Pin 30 or CN1 Pin 21 T-CON P703 Pin 36 or CN1 Pin 16 T-CON P703 Pin 38 or CN1 Pin 14 T-CON
P703 Pin 39 or CN1 Pin 13 T-CON P703 Pin 40 or CN1 Pin 12 T-CON

Interconnect page 2 of 4
37LK450 Ballast (Inverter) Drawing
7 6
Q505
U1
BALLAST COMPONENT VOLTAGE TABLE To Backlight
U1 PIN Run PIN Run
T10
1) 15.41V 13) 1.04V
Q101 PIN Run Q202 PIN Run DU11 PIN Run DU55 PIN Run 2) 9.12V 14) 1.98V
1 5 D201 Q202
1 1) 10.86V B
B) 2.9V 1
1) 0V 3
1) 0V 5 1 Q201 3) 9.12V 15) 0.1V
C 2
2) 24V E C) 0V 3 2) 1.58V 2 1 2) 1.6V Q311 4) 0V 16) 1.44V
3) 8.96V E) 0V 3) 0V 3) 2.61V To Backlight T9 5) 3.28V 17) 1.48V
Q801
6 7 6) 3.3V 18) 2.33V
Q102 PIN Run Q311 PIN Run DU12 PIN Run DU56 PIN Run DU64 7) 5.48V 19) 0V
DU59
1) 0V 1) 0V DU61
1) 3.17V C
B) 0.58V 1 3
DU15 DU63 8) 2.9V 20) 0V
2
2) 8.9V C) 0.06V 2) 1.59V 2) 1.26V DU58 DU62
1 3)
B E 3 2 1
DU57 9) 14.41V 21) 1.36V
0V E) 0V 3) 0V 3) 2.61V To Backlight 10) 14.44V 22) 0V
6 5
T8 11) 1.48V 23) 9.06V
Q103 PIN Run Q505 PIN Run DU13 PIN Run DU57 PIN Run 12) 0V 24) 14.7V
7 1
1 1) 11.23V C
B) 0V 1
1) 0V 3
1) 0V 5
8A F1
2
125V 24V
2) 24V B E C) 1.51V 3 2) 1.57V 2 1 2) 0.91V T7
3) 9.07V E) 0V 3) 0V 3) 2.65V To Backlight 1 270uF + -
DU14
35V
DU56
Q104 PIN Run Q701 PIN Run DU14 PIN Run DU58 PIN Run DU13 Q702 C164
1) 3.14V B) 11.03V 1) 0V 1) 0V DU55 Q103
2) 9.08V
C 1 2 3 7 6 +-
1 B E C) 8.97V 3 2) 1.6V 2 1 2) 1.23V
3) 0V 270uF
E) 10.87V 3) 0V 3) 2.66V To Backlight 35V
T6 C163
Q105 PIN Run Q702 PIN Run DU15 PIN Run DU59 PIN Run
B) 11.43V 1) 0V 1) 0V Warning: Over 2.9Kv Q107
1 1) 10.86V 1 5
B C 3 3
To each Backlight. 1 5
2) 24V E C) 9.08V 2 1 2) 1.54V 2 1 2) 1.41V
3) 10.86V E) 11.26V 3) 0V 3) 2.66V
To Backlight
T5 Q107
Q106 PIN Run Q703 PIN Run DU51 PIN Run DU61 PIN Run
1) 0V B) 3.29V 1) 2.6V 1) 0V 7 6
B C 3 1 2
2) 8.9V C) 0V 2 2) 0.52V 2) 0V DU54
E 1 3
1 3) Ballast
0V E) 3.16V 3) 0V 3) 24.12V
To Backlight 6 5
Q107 PIN Run Q704 PIN Run DU52 PIN Run DU62 PIN Run T4 Q104
1 1) 11.27V B
B) 3.27V 2
1) 0V 1
1) 0V 7 1
C 2
2) 24V E C) 0V 1 3 2) 0.8V 3 2) 3.09V 6 5
3) 9.08V E) 3.14V 3) 2.6V 3) 24.12V T3
Q704
To Backlight 7 1
Q108 PIN Run Q801 PIN Run DU53 PIN Run DU63 PIN Run DU53
DU12 Q701 +-
1) 3.15V C
B) 5V 2
1) 0V 1
1) 0V
2
2) 9.06V B E C) 0V 1 3 2) 1.66V 3 2) 3.32V 7 6
1 3) 0V E) 0V 3) 2.63V 3) 24.12V Q105 C162
Q101
To Backlight +-
D201 PIN Run DU54 PIN Run DU64 PIN Run T2
Q201 PIN Run
E B
B) 0V 1
1) 15.49V 3
1) 2.6V 1
1) 0V 1 5 C161
2 2
C C) 1.49V 3 2) 5.48V 2 1 2) 0.9V 3 2) 3.15V 1 5 Q703
E) 0V 3) 14.59V 3) 2.66V 3) 24.12V
Q106
To Backlight T1 DU52
Q102
DU51
7 6
DU11
Interconnect page 4 of 4 August 2011 37LK450 LCD-DV

37LK450 +3.5V_ST Voltage Distribution Circuits
+3.5V_ST
+3.5V_ST
P401
2 1
PWR_ON Switch
3
1, 2, 16
From SMPS Q402
IC407
+3.5V_ST Pin 9~12 +3.5V_ST Not On
1.5V_DDR
1, 2, 16 Not On
IC403 +3.5V_ST in Additional Information
1.26V_DDR
Other components using 3.5V_ST
Not On
R1009 Model_OPT_1 pull up
+3.5V_ST
P1001 Debug R1075 Model1_OPT_2 pull up
4
Micom
MAIN BOARD R2404 Key1 pull up
Reset +3.5V_ST R2405 Key1 pull up
+3.5V_ST
R1046
C1010 Note: Components in Grey are on the
R1039 +3.5V_ST
X1002 back and are flipped for from view.
32.768KHz Micro JK803
DS
48 HDMI 3
IC1002 D825 CEC Remote
GB
+3.5V_ST Q805
IC1001 EEPROM HDMI Side CEC
Q2405
IR Buffers Head Phone Mute Q1105
+3.5V_ST Q2406
+3.5V_ST
P2401
To Ft IR
Pin 6 Amp Mute JK3301 HP
JK1104 (PC)
Driver
Q501
Q1106
Head Phone Mute Driver
+3.5V_ST JK1101 (RS232) +3.5V_ST
IC1101
RS232 Data
HDMI 2 CEC HDMI 1 CEC
JK801 JK802
LG TRAINING
CENTER 5 August 2011 37LK450 LCD-DV
37LK450 +12V Voltage Distribution Circuits
IC408 +12V Power Det

+12V IC408 IC401
3
P401 5V_USB
+12V 21
G S
Q409
+12V
D
IC406
Panel Vcc IC405 +12V
From SMPS 12V +5V_Normal
Switch
Pin 17, 19, 21
+12V
+3.3V_Normal
MAIN BOARD
6
LG TRAINING
CENTER
August 2011 37LK450 LCD-DV
37LK450 +24V Voltage Distribution Circuits
+24V
P401
3
IC409
21
Power Det 24V
From SMPS +24V
Pin 2, 3, 4
MAIN BOARD
Note: Components in Grey are on the

back and are flipped for from view.
Audio Amp
32~35
IC501
+24V
L509 L508
L507 49~52
L506
P501
R-R+L-L+
7
LG TRAINING
CENTER
August 2011 37LK450 LCD-DV
37LK450 Other Voltage Distribution Circuits
Additional circuits utilizing +3.5V_ST: Additional circuits utilizing +3.3V_Normal: Additional circuits utilizing +12V: Additional circuits utilizing +24V:
Reset for Microprocessor: C1010 and R1046 CEC Remote: Q806 IC408 Power_Det: R448 IC409 Power_Det: R482
Key 1 and Key 2 pull up: R2401, R2405 DSUB_Det: R1146 Panel Power Drivers: R431 to Q406, R439, R440 to Q407
S/T_SCL R4043, S/T_SDA R4035 HP_DET: R1155
Micom Model Option 0~3 pull up: Write Protect (WP): IC1401 pin 3 R1403
R1071, R1009, R1075, R1079 IC_AGC_MAIN Pull Up: L227 R4019
IR Buffers Q2405, Q2406 FRC_RESET: R205 Pins
Pin 8
L412 L702 P703 IC1105
CEC Remote: Q805 AV_CVBS_DET: R1660 Q409 1~4
Amp Mute: Q501 SC1/COMP1_DET: R1613 Panel_VCC Pin D LVDS to T-CON RGB PC EDID
Pin S D1115
COMP2_DET: R1612
Pin 8
LED_DRIVER_D/L_SCL R2100 / SDA: R2101 L401
IC401 L406 IC1450 IC804
Additional circuits utilizing +5V_Normal:
PWM_1&2 Pull Up: R115, R117 +5V_USB Pin Pins USB OCP HDMI Side EDID
/PCM_IRQA Pull Up: R132, /PCM_Wait Pull Up: R133 Pin 2
D824
I2C Pull Up: R140~R145 7,8 2,3
Pin 8 IC801
HDMI 1 EDID
Pins D821
12V L417 7,8 L422 Pin 8
IC406 +5V_Normal IC802
+5V_Normal HDMI 2 EDID
Pin 2 D822
From SMPS P201 Q405 P401 pin 18 to
pins 17, 19 and 21 to P401 INV_CTL SW SMPS P201
L402 12V L416 IC405 Through R419 to Collector
+12V +3.3V_Normal
Pin 2
From SMPS P201 pins 9~12 IC104 EEPROM (Saturn)
Pin 8 L3702
to P401
+3.3V_Normal
L404 L420 L423 JK1103 Optical Out
IC407 Q408 L2404 Pin 2
+3.3V_ST +1.5V_DDR +1.5V_FRC_DDR P1402 to Ft. IR +5V_TU
Pin 1,2 Pin Pin 6
Pin D Pin S
10~12 IC1401 S-Flash Memory
Pin 11-12
P401 pin 1 to Q402 IC1002
IC102 NAND Flash Memory
SMPS P201 PWR_ON SW Micro L301 Pin 12, 37
Pin 3 Pin 1 Pin 48 VCC1.5V_U3_DDR
23 L210 L1203 IC1202 USB Select Pin 3
AVDD_DDR_FRC +3.3V_USB
Pin 5, 10, 23, 29, 36 Pin 14
L3703
+3.3V_Normal +3.3V_TU
P2402 L2403 IC1001 +3.3V_Normal TU3702
Pin 3
To Ft. IR Pin 8
EEPROM Micro IC3703 TUNER
Pin 6 L217 +1.2V_TU
AVDD_DMPLL +1.26V_TU
IC1101 Q1105 Pin 2
Pin 13
RS232 Side_HP_Mute L204 +3.3V_Normal Pin 3
IC404
Collector IC101 VDD33
Saturn +1.8V_AMP Pin 2
L413 L222 L502 L501
Video Pin 1
FRC_VDD33_DDR Pin 16 Pin 12 Pin 13
Processor IC402
Pin 1,2 L217 +2.5_Normal L504
+3.3V_Normal Pin 13
IC403 AU33
Pin 3
L212
+1.26V_VDDC AU25
L211
AVDD2P5 From SMPS P201 IC501 Audio Amp
L228
MIU0VDDC L221 pins 2, 3 and 4 to P401
L225 FRC_AVDD L407
FRCVDDC L219 +24V +24V Pin 32, 33, 34, 35 Right CH
AVDD25_PGA Pin 49, 50, 51, 52 Left CH
LG TRAINING
CENTER
8 August 2011 37LK450 LCD-DV
42CS560 INTERCONNECT DIAGRAM
VGL -5.3V pin 9, 13 VCC 3.3V pins 36, 67
(1) PVDD 16.46V VCC 3.3V PVDD 16.46V VCC 3.3V
PWR-On Pin 1: Turns on 12V, 24V (21V) to the Main and 398V to the on board Ballast circuit. VGH 27.53V pin 11
HVDD 8.04V HVDD 8.04V HVDD 8.04V pins 38, 39
(2)
INV-On Pin 18: Turns on the Backlights PVDD 16V pins 19, 20 PVDD 16V pins 41, 42
(3)
Error_Out Pin 24: Goes high (3.3V) when the backlights are told to come on. Goes back low when they light. HVDD 8.04V pins 21, 22 TO TFT MODULE TO TFT MODULE VGL -5.3V pin 48, 52
If it goes high again on the 5th attempt to fire the backlights, the Ballast shuts off. VCC 3.3V pins 24, 25 CN5 CN4 VGH 27.53V pin 51
(4)
A-DIM Pin 20: Is not used (Fixed Voltage). C106 C102 C109 C103
(5) C107
P-DIM Pin 22 can vary according to incoming video IRE level and OSD Backlight setting Output from the HVDD 8.04V C105 C110 C101
C108 C104
Video Processor IC100. Range 0.95V to 2.64V. VGL -5.3V pin 9 X1 VGL -5.3V pin 52 PANEL TEST
U3
D10 To run the T-CON “Panel Test”,
F4 and F5 are ground L3 D3 remove the LVDS cable. Jump
3.44V protection EMI Filters. 12V from SMPS to the 12V fuse.
D202 US2 VGL -5.3V
Failure to return both UC1 VGH 27.53V (Use top leg of D202 for easy
D202 screws with the shield FL5
PVDD 16.46V D11 FL4 access to 12V)
D206 D2
removed can cause VCC 3.3V D4 US1 Jump VCC 3.3V (Just left of L2)
1 D5
these to open. 2 to pin 44 on CN1. White, Red,
U6 3 F1 P401 to SMPS P201
12V Blue, Green and Black patterns
D201 P201 LD0 Test L2 12V L1 show on screen. Pin Diode
CN1 1 OL
U5 12V
T701 T702 T501 D204 Gnd 12V 2-4 2.92V
Hot Gnd
d
5-8 Gnd
ol
IC502
C
(Shock Hazard)
12V Pins 48 ~ 51 and 9-12 0.64V
ot
Warning: Return the Screws when the Shield is
H
LVDS Video Signals removed for Service if Power is going to be applied. 13-16 Gnd
IC503 P201 "SMPS Board" To P401 "MAIN Board"
17 OL
SMPS D601 Pin Label STBY Run Diode Check 18 1.57V
Q709 P/N: EAY62769601 L600 24 ERROR 0V 0V Open 19 OL
Backlight Drive 20 OL
23 n/c n/c n/c Open See LVDS waveforms on
Signal TP
Q710 Q602 Page 2 of Interconnect Diagram 21 OL
R403 Same as 22 P-DIM 0.02V 0.95V~2.64V Open
IC501 22 2.57V
F501
21 12V 0V 12.27V Open 23 n/c
100uF
450V
Q707 20 A-DIM n/c 1.53V Open 24 OL

-
19 12V 0V 12.27V Open For Voltages

R406 Q708 STBY: 1.24V See P201 SMPS
18 INV-ON/OFF 0V 2.96V Open 3.43V on ERROR
RUN: 396.8V
line indicate a Panel_VCC
P703 LVDS
17 12V 0V 12.27V Open Q409
Backlight firing P401 EEPROM D S E B
Backlight Drive F501 16 Gnd Gnd Gnd Open fault. Q405 G
Signal TP IC104
C 12V out IC1000
P401 3.15A/250V INV_CTL
C
Q407 Pins 48-51
13-15 Gnd Gnd Gnd Gnd 3
PWR_ON Commercial
Hot B E
IC408 Q402 1 2 Q409 Driver
To Panel BD101 9-12 3.5V (Stby) 3.41V 3.39V Open PWR_Det
1
3 Q401 C E
B
Remote
2
Backlights T704 Cold +3.3V_Normal IC407
5-8 Gnd Gnd Gnd Gnd P2402 3
2
1
Q403
B
S G +1.5V_DDR L406
1.2Kv SK101 2-4 20V 0V 21.56V 0.82V
Q400 E C D
L415 IC402
2
P402 F100
Q403 Driver IC403
+2.5V_Normal
IC1450
To Panel 1 PWR_ON 0V 3.24V 0.91V To Front IR A IC1201 IC101
Backlights 5A/250V IC5601 +1.10V_VDDC DDR Micro IC401 USB_OCP
P2402 "MAIN Board" To J1 "IR Board" D200
T703 Video +5V_Normal
Pin Label STBY Run Diode Check C A1
Processor +5V_USB
AC In 15 S/T_SDA 3.34V 3.34V 3.0V
A2
14 S/T_SCL 3.34V 3.34V 3.1V Serial Flash X201 IC3703

Main
1
120Hz SMPS TEST 1 : Forcing SMPS On. SMPS Test P201 Open 13 Gnd Gnd Gnd Gnd IC501 2 2
12 LED_R 0V 0V OL 24Mhz
3
TUNER PINS
Remove AC Power. Pin No Load AUDIO Amp P/N: EBR75140001 +1.8V_TU 1. n/c
Q802
Disconnect P401 on Main Board. 24 0.03V
11 +3.3V_Normal 0.00V 3.26V 0.57V E B 2. Reset
HDMI Hot Swap (AUSYLUR, AUSYLHR, 3. SCL
Jump pin 1 (PWR_ON) to pin 9, 10, 11 or 12 . 10 Gnd Gnd Gnd Gnd C
6.6mS 23 n/c L504 L506 E B
A1 A2
AUSYLJR,) 4. SDA
Apply AC Power. This should force the SMPS to the 9 IR 3.34V 3.34V 2.68V Q801 C D821 5.+3.3V_TU
22 3.25V C
on state. All Voltages should be produced. 8 LED_R 0V 0V OL A1 A2
6. SIF
21 12.29V
DDC_SCL/SDA Pull Up No backside components 7. +1.8V_TU
(20V and 12V to Main). 397V Backlight Power. 7 Gnd Gnd Gnd Gnd L503 L505 D822
C
2Msec per/div 8. CVBS

Backlights are not on. 20 1.64V 6 3.5V_ST 3.41V 3.35V 0.65V 9. IF AGC
4.03V p/p 48KHz TU3700 10. DIF (P)
Disconnect AC Power. 19 12.29V 5 KEY 2 3.30V 3.31V OL 1
80% P-DIM 1 11. DIF (N)
18 3.41V 4 KEY 1 3.30V 3.31V OL
R403 Bottom leg SMPS TEST 2 : Forcing Backlights On. 17 12.29V 3 Gnd Gnd Gnd Gnd
R406 Bottom leg Leave first connector in place. P501
13-16 Gnd 2 Sensor_SDA 0V 3.23V 0.79V
Jump pin 18 (INV_ON) to pin 9, 10, 11 or 12. 1
9-12 3.41V
1 Sensor_SCL 0V 3.23V 1.14V p/n: EBU61719708 p/n: EBT62114904
Apply AC Power. Other p/n (AUSYLJR)
5-8 Gnd
(AUSYLUR and AUSYLHR)
This should force the Backlights to come on.
2-4 19.17V
P201 P201 To all Speakers
1 3.41V See DC Voltages for Main Board on
All pins 10.84V Page 3 of Interconnect Diagram
Front IR / Key Board Diode Test = OL
Intelligent Sensor Jumper Jumper

J1 Key 1 Line J1 or P2401 pin 4 Key 2 Line J1 or P2401 pin 5
Jumper Resistance Voltage Resistance Voltage
Volume (+) 1.96M Ω Volume (+) 1.68V CH (Up) 1.96M Ω CH (Up) 1.68V
Note: STBY 3.5V Must be Volume (-) 1.24M Ω Volume (-) 1.13V CH (Dn) 1.24M Ω CH (Dn) 1.13V
present when AC applied. Settings 540K Ω Menu 0.47V Power 540K Ω Power 0.47V
A Test 1 Test 2 OK 19.3 Ω Enter 0.01V Input 19.3 Ω Input 0.01V
Key 1 or 2, No Key Pressed, resistance: 15.85M Voltage 3.3V
42CS560 Main Board Component Voltages
IC1001 Micro IC403 +1.10V_VDDC IC408 Power_Det IC1450 5V Short Protection

Pin EEPROM Pin Regulator Pin 24V, 12V, 3.5V Pin for USB
[1] 0V (Gnd) [1] 3.33V (In) +3.3V_ST [1] 0V (Gnd) [1] 0V (Gnd)
[2] 0V (Gnd) [2] 3.33V (In) +3.3V_ST [2] 3.25V (Reset) [2] 4.98V (In)
[3] 0V (Gnd) [3] Do not Measure [3] 3.35V (In) +12V [3] 4.98V (In)
[4] 0V (Gnd) [4] 0V (Gnd) [4] 3.3V (USB-En)
[5] 3.25V (SDA) [5] 0V (Gnd) IC1000 Commercial [5] 4.96V
[6] 3.25V (SCL) [6] Do not Measure Pin Remote [6] 4.98V (Out)
[7] 0V (Gnd) [7] Do not Measure [1] 3.34V (C1+) [7] 4.98V (Out)
[8] 3.25V (B+) [8] Do not Measure [2] 8.8V (V+) [8] n/c (0V)
[9] 2.16V [3] 3.25V (C1-)
IC401 +5V_Normal [10] 1.23V (Out) [4] 3.34V (C2+) IC5601 Serial
Pin +5V_USB [11] 1.23V (Out) [5] V (V+) Pin Flash Memory
[1] 0V (Gnd) [12] 1.23V (Out) [6] (-5.7V ) (C2-) [1] 3.28V (In)
[2] 12.23V (In) [13] 4.61V (BOOT) [7] 0V (n/c) [2] 3.28V (In)
[3] 0V (Gnd) [14] 0V (n/c) [8] 3.34V (n/c) [3] 0V (Gnd)
[4] 1.23V (FB) [15] 3.24V (EN) 3.3V_Normal [9] 3.36V (n/c) [4] 0V (Gnd)
[5] 3.26V (COMP) [16] 3.33V (In) +3.3V_ST [10] 5.79V (n/c) [5] 0V (Gnd)
[6] 12.22V (EN) [11] 0V (DN1) [6] 0.8V
[7] 2.14V (SS) IC407 (+1.5V_DDR) [12] 0.04V (ROut1) [7] 0.86V
[8] 0V (n/c) Pin Regulator [13] 0V (RIn1) [8] 0.54V
For Output, use L406 [1] 3.33V (In) +3.3V_ST [14] (-5.73V ) (DOut1) [9] 1.75V
[2] 6V (n/c) [15] 0V (Gnd) [10] 1.33V (Out)
IC402 +2.5V_Normal [3] 3.33V (In) +3.3V_ST [16] 3.33V (In) +3.3V_ST [11] 1.33V (Out)
Pin Regulator [4] 3.24V (EN) +3.3V_Normal [12] 1.33V (Out)
[1] 0V (Gnd) [5] 0V (Gnd) IC3703 +1.8V_TU [13] 4.72V
[2] 2.54V (Out) [6] 2.09V (SS) Pin Regulator [14] n/c
[3] 3.25V (In) [7] 0.79V (FB) [1] 0V (Gnd) [15] 3.29V
[8] 1.53V (Out) [2] 3.30V (Reset) [16] 3.28V (In)
[3] 3.33V (In)
Q401 Power On/Off Q402 Power On/Off Q403 +3.3V_Normal

Q400 +3.3V_Normal Pin Driver for Q402 Pin Switch Pin Switch
Pin Driver for Q403 B 0.49V (RL_ON) 1 3.33V (In) +3.3V_ST S 3.33V (In) +3.3V_ST
B 0.65V (POWER_ON/OFF_1) C 0.07V (Ctrl) 2 3.35V (Ctl) G 0.07V (Enable)
C 0V (Ctrl) E Gnd 3 3.23V (Out) PWR_ON D 3.27V (Out) +3.3V_Normal
E 0V (Gnd)
D200 _
SOC_Reset D821 DDC_SCL1/SDA1
_ Q405 Inverter On/Off
Q407 PANEL_VCC Pin Speed Up Pin Pull Up Pin Switch
Pin Drives Q409 [C] 0V [A1] V (5V_HDMI_1) B 0.01V (INV_CTL)
B 0.0V [A] 0V [A2] 5.32V (+5V_Normal) C 2.98V (INV_On)
C 0.68V [A-C] 0V (Gnd) [C] 5.14V (Pull_Up) E 0V (Gnd)
E Gnd
Q801 HDMI 2 Q802 HDMI 1 D822 DDC_SCL2/SDA2
Q409 PANEL_VCC Pin Hot Swap Pin Hot Swap Pin Pull Up
Pin Switch B 0.66V (HPD2) B 0.66V (HPD1) [A1] 5.32V (5V_HDMI_1)
S 12.2V (In) C 0.04V (HDMI HS) C 0.04V (HDMI HS) [A2] 5.32V (+5V_Normal)
G 1.84V (Enable) E Gnd E Gnd [C] 5.14V (Pull_Up)
42CS560 LVDS P703 WAVEFORMS
P703 Pin 12 Main or CN1 T-CON P703 Pin 14 or CN1 T-CON P703 Pin 16 or CN1 T-CON and P703 Pin 19 or CN1 Pin 19 T-CON P703 Pin 22 or CN1 Pin 22 T-CON
P703 Pin 32 or CN1 T-CON
Clock (RX~CK-)
P703 Pin 13 or CN1 T-CON P703 Pin 15 or CN1 T-CON P703 Pin 20 or CN1 Pin 20 T-CON P703 Pin 23 or CN1 Pin 23 T-CON
P703 Pin 17 or CN1 and
P703 Pin 33 or CN1 T-CON
Clock (RX~CK+)
P703 Pin 24 or CN1 T-CON P703 Pin 28 or CN1 T-CON P703 Pin 30 or CN1 T-CON P703 Pin 35 or CN1 T-CON P703 Pin 38 or CN1 T-CON
P703 Pin 25 or CN1 T-CON P703 Pin 29 or CN1 T-CON P703 Pin 31 or CN1 T-CON P703 Pin 36 or CN1 T-CON P703 Pin 39 or CN1 T-CON
P703 Pin 40 or CN1 T-CON P703 Pin 41 or CN1 T-CON


42CS560 Main Board +3.5V_ST Distribution
+3.5V_ST Input: Pins 9, 10, 11, 12
P401
Q402 Not On in STBY
Not Activated
Turned on by +3.3V_Normal IC1000
until 12V arrives 3
IC408 L404 1 Q402 PWR_ON Commercial
2
1 Remote
PWR_Det 2 3
L420 IC407 Not On in STBY
IC407
To Front P2402 Q403 Turned on by +3.3V_Normal
IR / Keyboard +3.3V_Normal S G +1.5V_DDR
+3.5V_ST D Q403 Not On in STBY Turned on by
Output: R2404 L413 POWER_ON/OFF_1
Pin 6 L2403 R2405 L206
IC403 IC101
Key 2 +1.10V_VDDC Micro AVDD_NODIE
Key 1 L2401
IC403 Not On in STBY Video R143
L2402 S/T_SCL
Turned on by +3.3V_Normal Processor R149
C200 S/T_SDA
IC5601
SOC_Reset Serial Flash
For IC403, IC407, Q403 Voltage Distribution

see “Other Voltage Distributions”
LG TRAINING
CENTER Page 4 of Interconnect Diagram August 2012 42CS560 LCD
42CS560 Main Board +12V Distribution PWR_ON Q402: Turned on by Q401 turned on by IC101 RL_ON.
Input: Pins 17,19,21 +12V (For power to Q402, see +3.5V_ST Voltage Distribution) Panel_VCC
To T-CON
L412 R439
12V out Pins 48-51
Q409 R440
P401 Panel_VCC S P703 LVDS
E B
D G C
Panel_CTL
PWR_ON Panel_VCC Q407 R430
L402 +3.5V_ST
3
Q402 Q409 Ctrl. RL_ON
1 3
1 2
E Gnd R401
2 R406 C B RL_ON
USB
IC408 R448 Q401 Note: Q409 turned on by
PWR_Det Q402 Ctrl. PANEL_CTL from IC101 via Q407 +5V_USB 4
L406
1
+5V_Normal
L425
IC101 To pin 1
L401
Micro L1451 USB
Video +5V_Normal IC401 IC1450
+5V_Normal USB_OCP
Processor
+5V_USB
X201
24Mhz
DDC_SCL1/SDA1 Pull Up
D821
A1 A2
C
A1 A2
DDC_SCL2/SDA2 Pull Up D822 C
LG TRAINING
42CS560 Main Board +21V Distribution
NOTE: 20V is the label, but the Voltage is actually 21V
+20V (21V) PWR_ON:Q402: Turned on by Q401 turned on by IC101 RL_ON.

(For power to Q402, see +3.5V_ST Voltage Distribution)
Input: Pins 2 ~ 4
P401
PWR_ON
+3.5V_ST
3
Q402
2
1
E Gnd
L407 B RL_ON
R406 C
R401
Q401
Q402 Ctrl.
AUDIO Amp
L501
IC501
22 +24V_AMP
23
24 37 38 39
L504 L506
L503 L505
P501
LG TRAINING
42CS560 Main Board Other Voltage Distributions
After all voltages are +3.5V_ST Input: Pins 9, 10, 11, 12
turned on on the Main
board, Q405 is turned Q405 turns on
Off supplying INV_ON backlights
P401 EEPROM IC104
to the power supply (via
INV_CTL
pin 18) turning on the From Q403
C
backlights. Collector
pulled up by Q405 B E 18 IC407 Not On in STBY +3.3V_Normal
L404 Turned on by +3.3V_Normal
+3.3V_Normal through
INV_CTL
R419 R419 L420 IC407 L1209
+1.5V_DDR AVDD_MIU
To Front P2402 Q400 3 2 1
IR / Keyboard B C S
G
Q403 L1202
D
R433 IC402
E
AVDD_DRO 2
R428
+3.3V_Normal +3.3V_Normal
Output: L2404 IC1201 IC101 +2.5V_Normal
Pin 11 IC403 L415 DDR Micro
Turns on the IC403 Not On Video
Intelligent Q403 Turned on in STBY +1.10V_VDDC
Processor
Sensor by Q400 Turned on by MIUVDDC
POWER_ON/ +3.3V_Normal L228
OFF_1 IC3703
1
2 2
3
AUDIO Amp IC101

L208 R206
IC501 L502 AVDD_AU33 MODEL_OPT_3 +1.8V_TU
R4027
L204 MODEL_OPT_4
VDD_33 R4028
MODEL_OPT_5 TUNER PINS
R182 L211
URSA5_RESET 1. n/c
R226 AVDD2P5 2. Reset
MODEL_OPT_0
R211 L229 3. SCL
MODEL_OPT_1 AVDD2P5_MOD 4. SDA
R208
L219 TU3700 5.+3.3V_TU
MODEL_OPT_2
L227 R4019 AVDD25_PGA 11
6. SIF
IF_AGC_MAIN
R161 7. +1.8V_TU
Sensor_SDA
8. CVBS
R160 Sensor_SCL +3.3V_TU 9. IF AGC
R1660 L3703 1 10. DIF (P)
AV_CVBS_DET 11. DIF (N)
R1612 +3.3V_Normal
COMP2_DET
R141 From Q403
AMP_SDA
R140
AMP_SCL
R145
I2C_SDA
R144
I2C_SCL
LG TRAINING
42LG60 CIRCUIT INTERCONNECT DIAGRAM
TFT PANEL 16V Pin 89,90 TFT-Drive (T-CON) 16V Pin 2,3
D9
U11 U14
CN5 CN4 Q8
Common
3.3V Pin 86,87 3.3V Pin 5,6 A A (-6.05V) B (0V) 1 1.8V 4 0V 1 Gnd 5 3.3V
LD1 Blue LED TFT Drive PWB Check Gnd B C E (Gnd)
-4.3V Pin 84 1.8V -4.3V Pin 8 C C (Gnd) E 2 Gnd 5 Gnd 2 Gnd 6 2.9V
-4.3V Pin 84 3.2V 6.48V Pin 13 -4.3V Pin 8
SET 0FF Lamp Assist SET ON 24.38V Pin 80 16V Pin 89,90
24.38V Pin 80 US1 24.38V Pin 12 3.3V Pin 5,6 24.38V Pin 12 Common (-3.5V) C (9.47V) 3 1.55V 6 3.3V 3 Gnd 7 3.3V
3.3V Pin 86,87
LED OFF LED ON LED OFF 6.48V Pin 78 6.48V Pin 78 16V Pin 2,3 6.48V Pin 13 Q2 4 Gnd 8 3.3V
FL22 VCOMLOUT D10
Anode 0V Anode 11.6V Anode 11.6V A A (26.7V) 1 3.3V 4 Gnd
D10
3.3V 6.48V
Cathode0V Cathode 0V Cathode 9.5V
FL101
Gnd
U11 Neg Volt C A A (14.5V) 2 0.6V 5 0V
source
UC1 D9 24.38V FL102
U18
U15 FL20
1.83V
R436 R430 Gnd C (19.6V) 3 Gnd 6 0V
Pin 8
LD1 assist the backlights with firing in dimly lit rooms. -4.3V
Gnd U10 C411
Q2
The appearance of LD1 when the set is on appears to be lit dimly. 3.3V D31
Pin
16V
FL21 3.3V Pins
However there is a small hole in the back panel frame and the 42,43
L2
23,24
D30 FRONT SIDE OF MAIN PWB BACK SIDE OF MAIN PWB
T-CON PWB that allows the backlight to make it appear lit. U16 F1 (11.6V) 16.08V
11.6V IC800 IC807 IC802 (On Back) Q801 (On Back)
FL103 3A/125V Pins 25,26
LD1 L1
Gnd
Pins 37,38
5V Switching Regulator 2.6V Switching Regulator A2.6V-BCM 3.3V Regulator 5V Switch
11.6V
U14 From F1 ZD2 Function Pin Volts Function Pin Volts Name Function Pin Volts Function Pin Volts
Gnd
P2 "SMPS" to P801 "Main PWB" In from IC806 1 8.95V In 6,7,8,10 5V Gnd 1 0V Source C ST-5V
CN1 CN2 Q8 5V
On/Off 2 3.3V Out 1,2,3,4,5 2.6V Out 2 3.3V Control B RL-ON (PWR)
Odd Pins
12V In Out (+5V-TU) 3 5.0V On/Off 17 Power Control In 3 5V Gnd E 0V
Pin Label STBY Run Pin Label STBY Run
Pins 47~50 n/c 4 0.0V Use L801 left side to test output IC805 (On Back) IC405 uP Reset (On Back)
1 16V 0V 16V 2 16V 0V 16V
Gnd 5 0.0V Use any top pin of IC807 to test input 3.3V Switching Regulator A3.3V-BCM Reset by Charge of C431
3 Gnd Gnd Gnd 4 Gnd Gnd Gnd
IC806 IC820 Function Pin Volts Function Pin Volts
5 12V 0V 11.8V 6 12V 0V 11.8V 9V Regulator 1.2V Switching Regulator A1.2V-BCM In 2 5V In 1 3.3VST-MICOM
7 Gnd Gnd Gnd 8 Gnd Gnd Gnd Function Pin Volts Function Pin Volts Name Out 4 3.3V (A3.3V-BCM) Gnd 2 0.0V
Pins 17, 23 and 24
9 5V 5V 5.15V 10 5V 5.15V 5.15V Not Used LVDS In (+12V) 1 11.6V In 6,7,8,10 5V On/Off 1 Power Control-3.3V Out 3 Low to High to B Q400
11 5V 5V 5.15V 12 5V 5.15V 5.15V Gnd 2 0.0V Out 1,2,3,4,5 1.2V IC810 (On Back) Q902 (On Back)
13 Gnd Gnd Gnd 14 Gnd Gnd Gnd Pin 21 is a Out 3 9V On/Off 17 Power Control 1.8V Switching Regulator +1.8V-NTP 12V LVDS control to Q901
15 Gnd Gnd Gnd 16 Gnd Gnd Gnd Fixed Voltage
IC404 Use L014 left side to test output Function Pin Volts Function Pin Volts
Left 17 ERR 3.19V 3.3V 18 ACD 4V 4.57V 3.3V Regulator Use any top pin of IC820 to test input In 3 3.3V from IC802 Source C 12V
Backlight 19 PWR 0V 2.86V 20 INV 0V 3.29V Function Pin Volts IC404 uP 3.3V Out 2 1.8V (+1.8V-NTP) Control B LVDS-Panel-Control
Plug 21 ADIM 0.1V 1.68V 22 *PDIM 0V 3.38V Gnd 1 0V 3.3VST-MICOM Gnd 1 0V Gnd E 0V
23 SEL 0V 3.2V 24 SYNC 0V 0V P103 P104 Out 2 3.3V Function Pin Volts Name Q802 (On Back) Q901 (On Back)
X101
20.25Mhz P101 In 3 5V In 3 5V ST_+5V 5V Switch control to Q801 12V LVDS On control to P900 Pins 1~4
PDIM Pin 22 can vary according to OSD Backlight IC103 Out 2 3.3V Reset Function Pin Volts Function Pin Volts
setting. 0.9V 0% to 3.3V 100% Gnd 1 0V Gnd In C ST-5V Source 1, 3 12V
IC102 IC101
Control B RL-ON (PWR) Control 2, 4 Low from Q902
P2 LVDS
2 1
1st” short either pin 9, 10, 11 or 12 (5V) to Pin 19 (PWR) using a 10K resistor. Gnd E 0V Output 5~8 12V
This turns on the power supply. TRU-MOTION P102
4 3
2nd: To test the Backlights, jump Pin 20 (INV) to Pin 19 (PWR) PANEL TEST: To run the T-CON without the Main board. Tuner Pin 16 SMTE Color bar In Right
6 5 IC108 IC109 IC110 With no power applied to the SMPS, disconnect both LVDS
Observe the Backlights. Backlight
8 7 If normal, the backlights should turn on and off 4 times. Then they go off. Cables CN1 and CN2.
Jump 12V from the SMPS (P201 pins 5 or 6) to F1 fuse on
Plug
10 9 If only ½ the backlights light, (Right side or Left Side), confirm connectors are OK.
12 11 If yes, panel defective. IC108 IC109 IC110 the T-CON.
If no backlight activity, confirm the Fuse F700 has approx. 300V on both sides. 5 (1.2V) 5 (0V) 5 (2.5V) Jump 3.3V from the VCC Test point (Bottom of L2) to pin 44
14 13
If on one side, check fuse for open. 4 (1.3V) 4 (1.79V) 4 (0V) of CN1.
16 15 10K
If no 300V, replace Power Supply. 3 (0V) 3 (0V) 3 (0V) Apply AC power to the SMPS.
18 17
If 300V present, observe the center leg on the left hand side of ballast transformer 2 (3.37V) 2 (3.36V) 2 (3.3V) The T-CON will product patters on the screen, Red, Green,
20 19
T701. Look for 45Khz pulse at 8.7V p/p. 1 (3.29V) 1 (3.29V) 1 (3.37V) Blue, etc.
22 21
If yes, confirm connectors to backlight OK, if OK, then panel defective.
24 23
If no pulse, replace the Power Supply.
IC807
MAIN PWB P800 P900 IC1201
Pin 24 IC600 IC820
Pin 23 *Q902 *Q901
P2 P801
LD803
Tweeter Tweeter IC302 IC304
Scope IC503 3.3V BCM *IC400
test point Backlight pulse over IC805
Reset See next page for
BCM IC100 IC300 IC1200
1000V p/p (45KhZ) Ft. PWB OK LED Waveforms for
IC701 BCM IC202 P900 using SMTE
P402 POWER SUPPY Assy. J1 IC402 IC500 *IC805 IC303
Color bar as the
Spk Spk
F101 Input.
Ballast
F700 8A 250V
J2 LG TUNER
Pin 1 ~ 16
1 16
*IC802 X200 (54Mhz)
24Mhz
IC301 IC404
J3 IC900 IC806
5A 250V AC TUNER *IC810 IC1000
X400 Q400
Section J1 5V Pin 3
IC800
335V Video Pin 16 ATSC/QAM/ IC501
E B
P200
uP
P401 Ft. TOUCH Audio SIF Pin 14 NTSC P501 P401 Not Used
AC In IC407 *IC405
LED/Push Sw
F700 90V in Stand-By
Side Control Keys *Grayed out components on the back
P100
LVDS CABLE P900 FROM MAIN BOARD TO TRU-
MOTION BOARD P101 USING SMTP COLOR BAR INPUT
Two Waveforms on the Right are Using the Tuner
Measurements +/- 5%
42LG60 :: Interconnect
TFT PANEL
LD1 Blue LED TFT Drive PWB Check
SET 0FF BOOT OK SET ON US1

LED OFF LED ON LED OFF 0V
1.8V
Anode 0V Anode 11.6V Anode 11.6V 3.2V FRONT SIDE OF MAIN PWB BACK SIDE OF MAIN PWB
CN5 CN4
Cathode0V Cathode0V Cathode 9.5V IC800 IC807 IC802 (On Back) Q801 (On Back)
5V Switching Regulator 2.6V Switching Regulator A2.6V-BCM 3.3V Regulator 5V Switch
The appearance of LD1 when the set is on appears to be lit dimly. U15 LD1 Function Pin Volts Function Pin Volts Name Function Pin Volts Function Pin Volts
However there is a small hole in the back panel frame and the UC1 In from IC806 1 8.95V In 6,7,8,10 5V Gnd 1 0V Source C ST-5V
T-CON PWB that allows the backlight to make it appear lit. On/Off 2 3.3V Out 1,2,3,4,5 2.6V Out 2 3.3V Control B RL-ON (PWR)
U16
Out (+5V-TU) 3 5.0V On/Off 17 Power Control In 3 5V Gnd E 0V
TFT-Drive (T-CON) n/c 4 0.0V Use L801 left side to test output IC805 (On Back) IC405 uP Reset (On Back)
Gnd 5 0.0V Use any top pin of IC807 to test input 3.3V Switching Regulator A3.3V-BCM Reset by Charge of C431
P2 "SMPS" to P801 "Main PWB" CN1 F1 CN2
IC806 IC820 Function Pin Volts Function Pin Volts
Odd Pins Even Pins 9V Regulator 1.2V Switching Regulator A1.2V-BCM In 2 5V In 1 3.3VST-MICOM
Pin Label STBY Run Pin Label STBY Run 3A 125V Function Pin Volts Function Pin Volts Name Out 4 3.3V (A3.3V-BCM) Gnd 2 0.0V
1 16V 0V 16V 2 16V 0V 16V In (+12V) 1 11.6V In 6,7,8,10 5V On/Off 1 Power Control-3.3V Out 3 Low to High to B Q400
11.6V
3 Gnd Gnd Gnd 4 Gnd Gnd Gnd Gnd 2 0.0V Out 1,2,3,4,5 1.2V IC810 (On Back) Q902 (On Back)
5 12V 0V 11.8V 6 12V 0V 11.8V Out 3 9V On/Off 17 Power Control 1.8V Switching Regulator +1.8V-NTP 12V LVDS control to Q901
7 Gnd Gnd Gnd 8 Gnd Gnd Gnd IC404 Use L014 left side to test output Function Pin Volts Function Pin Volts
3.3V Regulator Use any top pin of IC820 to test input In 3 3.3V from IC802 Source C 12V
9 5V 5V 5.15V 10 5V 5.15V 5.15V LVDS
11 5V 5V 5.15V 12 5V 5.15V 5.15V Function Pin Volts IC404 uP 3.3V Out 2 1.8V (+1.8V-NTP) Control B LVDS-Panel-Control
Gnd 1 0V 3.3VST-MICOM Gnd 1 0V Gnd E 0V
Out 2 3.3V Function Pin Volts Name Q802 (On Back) Q901 (On Back)
In 3 5V In 3 5V ST_+5V 5V Switch control to Q801 12V LVDS On control to P900 Pins 1~4
Left 17 ERR 3.19V 3.3V 18 ACD 4V 4.57V
Out 2 3.3V Reset Function Pin Volts Function Pin Volts
Backlight 19 PWR 0V 2.86V 20 INV 0V 3.29V
Gnd 1 0V Gnd In C ST-5V Source 1, 3 12V
Plug 21 *ADIM 0.1V 1.68V 22 PDIM 0V 3.38V
Control B RL-ON (PWR) Control 2, 4 Low from Q902
23 SEL 0V 3.2V 24 SYNC 0V 0V P103 P104
X101 Gnd E 0V Output 5~8 12V
20.25Mhz P101 LVDS
* ADIM Pin 21 can vary according to OSD Backlight
setting. 0.9V 0% to 3.3V 100%
IC103
IC101
P2
IC102 Right
st
1 ” short either pin 9, 10, 11 or 12 (5V) to Pin 19 (PWR) using a 10K resistor. Backlight
2 1
P102
4 3
This turns on the power supply.
2nd: To test the Backlights, jump Pin 20 (INV) to Pin 19 (PWR)
CONTROL Tuner Pin 16 SMTE Color bar In Plug
IC108 IC109 IC110
6 5
Observe the Backlights.
4
8 7 If normal, the backlights should turn on and off 4 times. Then they go off.
10 9 If only ½ the backlights light, (Right side or Left Side), confirm connectors are OK.
12 11 If yes, panel defective. IC108 IC109 IC110
If no backlight activity, confirm the Fuse F700 has approx. 300V on both sides. 5 (1.2V) 5 (0V) 5 (2.5V)
14 13
If on one side, check fuse for open. 4 (1.3V) 4 (1.79V) 4 (0V)
10K
2
3 (0V) 3 (0V)
16 15
If no 300V, replace Power Supply. 3 (0V)
18 17
2 (3.37V) 2 (3.36V) 2 (3.3V) See back side of page for Waveforms for
If 300V present, observe the center leg on the left hand side of ballast transformer
20 19
1 (3.29V) 1 (3.29V) 1 (3.37V) P900 using SMTE Color bar as the Input.
T701. Look for 58Khz pulse at 8.7V p/p.
22 21
If yes, confirm connectors to backlight OK, if OK, then panel defective.
24 23
If no pulse, replace the Power Supply.
L Pin 24
MAIN PWB
IC600 IC820 P800 P900
IC807
IC1201
G
Pin 23 *Q902 *Q901
P2 P801
LD803
Tweeter Tweeter IC302 IC304
Scope IC503 3.3V BCM *IC400
test point Backlight pulse over IC805
Reset
BCM IC100 IC300
1000V p/p (54KhZ) Ft. PWB OK LED IC1200
6
IC701 BCM IC202
P402 POWER SUPPY Assy. J1 IC402 IC500 *IC805 IC303
Spk Spk
F101
Ballast
F700 8A 250V
J2 LG TUNER
Pin 1 ~ 16
1 16
*IC802 X200 (54Mhz)
24Mhz
IC301 IC404
J3 IC900 IC806
5A 250V
0
AC TUNER IC1000
X400 Q400
Section J1 5V Pin 3 *IC810
335V Video Pin 16 ATSC/QAM/ IC800
IC501
E B
P200
uP
P401 Ft. TOUCH Audio SIF Pin 14 NTSC P501 P401 Not Used
AC In IC407 *IC405
LED/Push Sw
Side Control Keys *Grayed out components on the back
P100
78 Schematics 78
42LG60 :: WaveForms
4
2
L
G
LVDS CABLE P900 FROM MAIN PWB TO CONTROL 6
0
PWB P101 USING SMTP COLOR BAR INPUT
LAST TWO WAVEFORMS ARE FROM THE TUNER
Measurements +/- 5%
79 Schematics 79
LG
2017 Direct View TV Training
43LJ5000 WebOS 3.0 LED TV
MAIN BOARD LAYOUT
(Main Board and Component Voltages)
Published February 17th, 2017

Main Board Picture 65EF9500 (2015) T-CON Section
CN8831
CNB1
BA2
CN9
CNK9
February 2017 Page 01

LG
43LJ5000 Main Board Component Layout 43LJ5000 (2017) Main Board
Color Pin RUN (Voltage)
With Backlights unplugged. BL Power DB801 cathode
Red 1 Backlight Voltage: 125.3V ~ 126.6V
measures 64V Jumps to 150V then slowly bleeds down to 80V.
n/a 2 N/C
Measures 56V (Even in Stand-by) with BL disconnected.
Black 3 Backlight Ground Return: 6.32V ~ 32V
AC CNB1
Backlights Bright to Dark
CN8831
Ground
(AC) FB1 (5A/250V) LB802
In
DB4
DB3
125.9V
Hot
Cold Ground
QB801
54V
DB801
CXB1
MOVB1 DB801
3.41V Gnd Backlight Power
LCB1 UB801
DB805 6.31V
DB1
DB2
53.43V
DB105
Hot LCB4 QB804 DB802
QB806 6.79V Gnd
Ground QB802
HGnd Bridge
Rectifier
450V
-
28uF
DB103
+
161V
54V
Ground
HGnd
Cold
450V
-
28uF
Backlight Drive
CN13
USB
50% 36V p/p
+
161V QB101
2.88V 9.68V DB101
5V (15.89Vdc)
160V 160V 12V F2
T101
HGnd UB102
Gnd
12V
HDMI2
HGnd
CN3
290V 12.02V
2.06V 10.69V
PCB101 5V_STBY
CNB2 N/C Y1
LD2 QH5 24MHz
BA2 (SPK) CN9 (LVDS)

QM32
All SKP
Pins 6.02V QM31 QH1 1.66V 1.63V
UD2 UT2
UD1 5.14V Gnd
UA1 24MHz
Panel_VCC QM2
12V Y1 3.31V
Pins 1-4 QM1 LD3 2.60V p/p 2.60V p/p
1.16V
CNK9 Main to Ft IR/Joystick

PIN LABEL STBY RUN DIODE UR1
QK2
Drops to 0V when Power Button is pressed. 1 Power 3.32V 3.32V OL CN1 N/C CN4
CNK9
EB UL1
2 VCC 5.12V 5.12V 2.23V C
UF1 QH2 HDMI1
Drops to 4.7V when IR is received 3 IR 5.11V 5.11V 1.99V CN5 CN10
4 Gnd Gnd Gnd Gnd Component Audio
5 LED 1.14V 0.45V OL
6 n/c n/c n/c n/c
IR Pulses 5.68V p/p
February 2017 Page 02 LG

43LJ5000 (2014) Main Board
43LJ5000 Main Board Component Voltages
PCB101 *Pins 3-4 UF1 EEPROM QB801 Backlight Power QH5 QM32 5V_Switched
Pin Hot Gnd Reference Pin Microprocessor Pin Doubler Pin Pin For USB
[1] 10.69V [1] 3.31V [1] 3.41V [1] 0V [1] 0.08V
[2] 9.68V [2] 0V [2] 54V (Out) [2] 5.13V [2] 5.14V (Out)
[3] *HGnd [3] 3.32V [3] 3.41V [3] 0.39V [3] 5.16V
[4] *2.06V [4] Gnd
[5] 0V QB802 Backlight QK2 DB101 12V
UB102 [6] 0V Pin Driver Power Pin Pin Rectifier
Pin [7] 3.32V [1] 6.79V [B] 0.68V [1] T101 Pluse
[1] 9.62V [8] 3.32V [2] 6.31V (Out) [E] Gnd [2] 12.02V (Out)
[2] Gnd [3] Gnd [C] 0V [3] T101 Pluse
[3] 2.49V UR1
Pin QB804 QM1 12V DB103 54V Backlight
UB801 1.5V [1] Gnd Pin Pin Panel VCC Pin Doubler
Pin Regulator [2] 3.32V [1] 0.31V [1] 0.10V [1] T101 Pluse
[1] 11.22V [3] 0V [2] 4.40V [2] 12V [2] 54V (Out)
[2] 2.21V [3] Gnd [3] 12V [3] T101 Pluse
[3] Gnd UL1 3.3V
[4] 0.09V Pin Regulator QB806 QM2 DB802
[5] 0.15V [1] 0.27V Pin Pin Pin
[6] 1.52V [2] 5.12V (In) [1] 0.31V [1] 0V [1] 11.98V
[7] 1.56V [3] Gnd [2] 0.31V [2] 0V [2] 11.40V
[8] 1.59V [4] 5.12V [3] Gnd [3] Gnd [3] 11.98V
[5] 3.33V (Out)
UD1 1.16V [6] 3.33V (Out) QH1 HDMI QM31
Pin Regulator [7] 1.54V Pin Hot Swap Pin
[1] 5.10V [8] 1.54V [1] 0.39V [1] 0.62V
[2] Gnd [2] 0V [2] 0.08V
[3] 1.21V UT2 3.3V_Tuner [3] 5.13V [3] Gnd
[4] 5.14V Pin Regulator
[5] 0.19V [1] Gnd QH2 HDMI
[2] 3.31V (Out) Pin Hot Swap
UD2 5V_STBY
5V STBY [3] 5.14V
5 14V (In) [1] 0.61V
0 61V
Pin Regulator [2] 0.01V
[1] 0.46V QB101 SMPS (Switch) [3] Gnd
[2] 12V Pin Hot Gnd Reference
[3] 5.19V [1] HGnd
[4] Gnd [2] 160V (Out)
[5] 9.90V [3] 2.88V
[6] 6.32V
[7] 4.87V
[8] 0.81V
February 2017 Page 03

47LV4400 INTERCONNECT DIAGRAM CN202 "SMPS Board" To CN4 "MAIN Board"
J4 "MAIN Board" To
CN202 "SMPS Board"
Note: If a particular area is exhibiting a dimmer backlight level than other areas or the overall brightness seems dim, be (1)
sure to first check the customer’s Menu setting for Backlights. Raise the percentage and see if the overall brightness PWM Pins 12~14 can vary according to incoming Pin Label STBY Run No Load Diode Check Pin Diode
returns to normal. If not, Check the P-DIM level, it should rise with the percentage shown on screen. video IRE level, OSD Backlight setting and then
100% = 3.3V. Follow the P-DIM signal all the way to the SMPS. LED Drive Signal 50 IRE Intelligent Sensor (room light condition). 14 (1)
P-DIM3 0V 0.69V~3.3V 3.36V OL 14 OL
You can also test each of the 16 blocks functionality by grounding the return path signal (using 220Ω resistor). Off Output from the Microprocessor.
13 (1)
P-DIM2 0V 0.72V~3.3V 3.36V OL 13 OL
Range 0.69V to 3.3V.
LED SINGLE BLOCK TEST (DIM OR DARK PICTURE AREA): For DC voltages for Main board
Turn the Brightness, Contrast and Backlights all the way up.
To the Panel Backlights PWR-ON: Starts 12V 12 (1)
P-DIM1 0V 0.69V~3.3V 3.36V OL 12 OL
components see pages 2, 3 and 4 of the
Confirm 50V on C700 +. and 40V LED Power.
On 11 BL-ON/OFF 0V 3.27V 0V (4.77V) OL 11 OL Interconnect diagram.
Confirm P-DIM is approx. 3V. Using a 220Ω resistor, jump any of No Backlights.
7.51V p/p 2.5mSec
the blocks grounding pin on LCN1 or LCN2 while observing the 10 PWR_ON 0V 3.27V 4.77V OL 10 OL
picture and each block should turn on maximum. BL-ON: Starts For LVDS video signal waveforms see
HGnd page 5 of the Interconnect diagram.
LCN1 White Plug "SMPS Board" To "Panel LEDs"
Backlights 8-9 12V 0V 12.81V 12.87V 1.64V 8-9 1.64V
PFC 6.23V LCN2 LCN1 LED Power goes to
Pin Label Run Diode Check R804A 4-7 Gnd Gnd Gnd Gnd Gnd 4-7 Gnd
C800B
101V 50.
1 VLED 50V OL 0V HGnd
Q800 1-3 +5VSB 5.24V 5.22V 5.24V OL 1-3 OL
6.3V each
-
450V
450V
450V
68uF
68uF
68uF
2 n/c n/c OL HGnd 20.6V HS5
pin
+
Backlight Driver Section
D801 HS3 PC601 Test1 Test2
3 R8 *0.86V~11.67V OL
D800B 307V 21.24V To SMPS To Spk
4 R7 *0.86V~11.67V OL 398V
398V Q600
5 R6 *0.86V~11.67V OL 170V 50V BL_PWR 100V To SPK
L801
-
398V C701C 220uF CH
TL1 TL3 J4
+
Outside legs 14 pin
6 R5 *0.86V~11.67V OL
113V
165V
Gnd Panel_ Panel_PWR J5
7 R4 *0.86V~11.67V OL Q601 - +
50V Gama TU1 F2 F1 CH
3.54V
BL_PWR TU2
220uF
8 R3 *0.86V~11.67V OL C700
100V
D800A
165V Hot D700 TL4 E 12V 5V_ST
L41 L36 L44 L45
HGnd C C TQ21
9 R2 *0.86V~11.67V OL Ground T601 B
C
B
C Q14 E
B
C
Hot Ground J28 E
TL6
C
10 R1 *0.86V~11.67V OL 1 U21 Q30
Reference 112V BL_On/Off TQ20 LVDS_VDD U51 B E
Vol
11 n/c n/c OL Outside legs 25V TU3 Level Q47 C
R915 Gnd
Shifter Q46
C
B U9 Q8 B Audio Amp
12 VLED 50V OL - +
TU14 C
E
Bridge 398V 398V 25V

B E E
Vol
TCN1 E
L43
T901
C
*White to Black screen DV33
560uF
B
U50
50V
HS1 C961 C958 D120 TQ22
LCN2 Black Plug "SMPS Board" To "Panel LEDs" Do not
C120A TU13 VCCK A1 Enter
Measure
- + - +
VO D28 C C A2 C D25
5V_ST 70 Grayed out
U6 D27 A2 A1 C
Pin Label Run Diode Check A2 A1
2200uF
2200uF
components U52 B E Q66 Home
C
10V
10V
BE
1 VLED 50V OL
IC901 PC901 J9
Q70
2 n/c n/c OL
HGnd 3.89V
D950 5V_ST CN202 are on the DDVR L42
F1 3.38V 4.91V 1
Gnd
TFT_ back side. A V V Input
19.45V 5V_ST d O I 312
3 L1 *0.86V~11.67V OL 5A/250V 19.6V 1.2V Driver
j
Outside legs PWR
4 L2 *0.86V~11.67V OL PC903 Gnd HS4 3 F3
5 L3 *0.86V~11.67V OL TCN2 U48 U8
Hot ZD301 U14 U46
DDR +5VSB
6 L4 *0.86V~11.67V OL Ground
12V USB
7 n/c n/c OL N L 70 VBS_Processor
Chassis Ground
8 L5 *0.86V~11.67V OL
CN101 MEDIATEK
Video/Micro
Processor
9 L6 *0.86V~11.67V OL
To Ft. IR J14 ARM
MT5376JFMU
U10 12V in
AC Q27
N
I
+5V_Tuner
Gnd
C E
G
d
n
10 L7 *0.86V~11.67V OL B U15 Y1 HDMI 1
O
Q17
C E C
B
E U18 U13 Q40
U34
C B E
11 L8 *0.86V~11.67V OL B E
DC Voltages to the Panel DC Voltages to the Panel Q15 U32 C
12 n/c n/c OL developed by on the Main Board, developed by on the Main Board, Q16 G
B C
54MHz TUNE EB
Q29
D
Output from TCN1 Output from TCN2
13 VLED 50V OL
S
2 R U30
VCC pins 35, 36 from TL1 VCC pins 25, 26 from TL1
Q41 TDVW- HDMI 2
*White to Black screen
Made by TU1 pins 35, 26 (3.3V) Made by TU1 pins 35, 26 (3.3V)
Q71 C BE U4
H_VDD pins 38, 29 from TL4 H_VDD pins 22, 23 from TL4 U53 H814F(A) C
S
U43 3 2 1 Q36 B E A1 A2
U22
G
Made by TU1 pin 8 (7.88V) Made by TU1 pin 8 (7.88V) D
S
D
Q72 MAIN BOARD Q69
D54 C
CN202
G B
C C C
VDD pins 40, 41 from TP12 VDD pins 20, 21 from TP12
Q18 E C E
Made by TU1 pin 18 (16.47V) Made by TU1 pin 18 (16.47V) BE B

C
D11 p/n: COV31310701
U31 D57 A2 A1
Test 1 A2 A1
1) Disconnect Main Board.

VST pin 47 from TU3 pin 15 VST pin 14 from TU3 pin 15 Q42 Q37
B
E C
(-4.93V) (-4.93V)
2) Using 10K resistor, jump 5V_ST
VGL_I pin 48 from TTP 14 VGL_I pin 13 from TTP 14
(pin 1) to PWR_ON (pin 10). Made by diode TD3 (-5V) Made by diode TD3 (-5V)
Optical
3) Apply AC power. HDMI 2
In RGB/DVI
Audio
Out
Audio
VGH_EVEN pin 49 from TU3 VGH_EVEN pin 12 from TU3
(PC)
RGB
Check 12V (pins 8-9).
Note; If there is a problem with a load from Pin 13 Pin 13
Y/V
Pb
Pr
R
10KΩ Check BL power (40V).
the panel backlights, you can remove AC and Made by TU3 pin 13 (-5V to 26V) Made by TU3 pin 13 (-5V to 26V)
No Backlights at this time. Toggles every second Toggles every second
Disconnect either LCN1 or LCN2. When AC
is reapplied, the Backlight LEDs should turn VGH_ODD pin 50 from TU3 VGH_ODD pin 11 from TU3
Test 2 on for about 2 seconds and then they turn off. Pin 12 Pin 12
J14 "MAIN Board" to "IR Board" to J1
CN202 Made by TU3 pin 12 (-5V to 26V)
Toggles every second
Made by TU3 pin 12 (-5V to 26V)
Toggles every second
Pin Label STBY Run Diode Check
1) Remove AC Power. VGH_R pin 52 from TU3 VGH_R pin 52 from TU3 1 IR 3.96V 3.95V OL
2) Leave pin 1 to pin 10 connected. Pin 10 Pin 9 2 IR_LED_POWER 5.24V 5.19V 0.99V
Made by TU3 pin 12 (-5V to 26V) Made by TU3 pin 12 (-5V to 26V)
3) Using 10K resistor, jump 5V_ST Toggles every second Toggles every second 3 Gnd Gnd Gnd Gnd Ft. IR/Intelligent Sensor
(pin 2) to BL_On (pin 11). J1
4) Apply AC power.
Video (LRLVRO-2+/-) pins 28-33 Video (RMLVO-2+/-) pins 28-33 4 LS_SCL 3.42V 3.37V OL Front IR
Video Clock (LMCLK+/-) 26, 27 To the Panel Video Clock (RMCLK+/-) 34, 35
5 LS_SDA 3.42V 3.37V OL
Check BL power (50V).
6 Light_Sensor_Det 3.56V 3.47V OL
10KΩ Check BLs come on. Video Signal Levels: p/p: Approx: 740mV p/n: COV31147501
(Backlights On). 7 LED_R 3.62V 3.82V OL
PANEL p/n: COV31311201
8 LED_B 3.03V 3.86V OL
47LV4400 Main (Front Side) Flat Pack IC Voltages
U6 VCCK (Core PWR) U14 System U30 HDMI U43 RGB (PC) U51 Audio TU14 T-CON
Pin Regulator Pin EEPROM Pin EDID Pin Data Buffer Pin Amplifyer Pin EEPROM
[1] 5.19V [1] n/c [1] 0V (Gnd) [1] 3.30V [1] 12.64V (Mute) [1] 0V (Gnd)
[2] 0.8V [2] n/c [2] 0V (Gnd) [2] 3.85V [2] 12.64V [2] 0V (Gnd)
[3] Gnd [3] n/c [3] 0V (Gnd) [3] 4.94V [3] 2.98V (L In) [3] 0V (Gnd)
[4] 0.8V [4] 0V (Gnd) [4] 0V (Gnd) [4] 4.99V [4] 2.98V [4] 0V (Gnd)
[5] 5.19V
5 19V (Enable) [5] 3.37V
3 37V (SDA) [5] 4.99V
4 99V (SDA) [5] 3.3V
3 3V [5] 1.57V
1 57V (n/c) [5] 4.99V
4 99V (SDA)
[6] Gnd [6] 3.37V (SCL) [6] 4.94V (SCL) [6] 0V (Gnd) [6] 0V (n/c) [6] 4.94V (SCL)
[7] 1.14V (Out) [7] 3.37V (WP) [7] 4.92V (WP) [7] 0V (Gnd) [7] 12.7V (AVCC) [7] 4.92V (WP)
[8] 5.2V (In) [8] 3.37V (VCC) [8] 4.94V (VCC) [8] 0V (Gnd) [8] 0V (Gnd) [8] 4.94V (VCC)
[9] 4.99V [9] 6.92V
U8 AV125 (1.25V) U18 Serial U31 HDMI [10] 4.98V [10] 3.56V
Pin Regulator (Analog) Pin Flash Pin EDID [11] 4.98V [11] 2.99V
[1] 1.25V (Adj) [1] 3.37V [1] 0V (Gnd) [12] 3.3V [12] 2.99V (R In)
[2] 1.25V (Out) [2] 3.06V [2] 0V (Gnd) [13] 4.98V [13] 0V (n/c)
[3] 3.37V (In) [3] 3.37V (WP) [3] 0V (Gnd) [14] 3.3V [14] 0V (Gnd)
[4] 0V (Gnd) [4] 0V (Gnd) [15] 3.28V [15] 12.79V (PVCC)
U9 DV33 (Core PWR) [5] 0V (Gnd) [5] 4.99V (SDA) [16] 4.99V (VCC) [16] 12.79V (PVCC)
Pin Regulator [6] 0V (Gnd) [6] 4.94V (SCL) [17] 12.9V
[1] 5.19V [7] 3.37V (VCC) [7] 4.92V (WP) U50 Audio [18] 6.3V (R Out)
[2] 0.8V [8] 3.37V (VCC) [8] 4.94V (VCC) Pin Op Amp [19] 0V (Gnd)
[3] Gnd [1] 6 06V (Left Out)
6.06V [20] 6 3V (R Out)
6.3V
[4] 0.8V U21 LVDS Power U32 HDMI [2] 6.06V (Left In) [21] 12.93V
[5] 5.19V (Enable) Pin Switch Pin EDID [3] 6V [22] 12.77V
[6] Gnd [1] 12.78V (In) [1] 0V (Gnd) [4] 0V (Gnd) [23] 6.12V (L Out)
[7] 1.14V (Out) [2] 0.05V (Ctrl) [2] 0V (Gnd) [5] 6V [24] 0V (Gnd)
[8] 5.2V (In) [3] 12.78V (In) [3] 0V (Gnd) [6] 6.02V (Right In) [25] 6.19V (L Out)
[4] 0.07V (Ctrl) [4] 0V (Gnd) [7] 6.02V (Right Out) [26] 12.75V
U10 +5V_Tuner [5] 12.77V (Out) [5] 4.99V (SDA) [8] 12.06V (VCC) [27] 12.79V (PVCC)
Pin Regulator [6] 12.77V (Out) [6] 4.94V (SCL) [28] 12.79V (PVCC)
In 12.78V (In) [7] 12.77V (Out) [7] 4.92V (WP)
G 0V (Gnd) [8] 12.77V (Out) [8] 4.94V (VCC) U53 Head Phone Audio
Out 4.9V (Out) Pin Amplifyer
U22 HDMI U52 DDVR [1] 0V (Gnd) [14] 0V
U13 System Pin EDID Pin Regulator [2] 0V (R In) [13] 0V (L In)
Pin Reset [1] 0V (Gnd) [1] 3.37V (In) [3] 0V (R Out) [12] 0V (L Out)
1GGndd [2] (Gnd)
0V (G d) [2] 1.80V
1 80V (Out)
(O t) [4] 0V [11] 3.25V
3 25V
2 5.18V (Reset) [3] 0V (Gnd) [3] 0.55V (Adj) [5] 3.23V (Mute) [10] 0V (Gnd)
3 5.12V (In) [4] 0V (Gnd) [6] -3.12V [9] 3.25V
[5] 4.99V (SDA) [7] -1.57V [8] -0.07V
[6] 4.94V (SCL)
[7] 4.92V (WP)
[8] 4.94V (VCC)
47LV4400 Main (Front Side) Transistor Voltages
TQ20 VGH Reg Q17 RED_LED Q47 3V3_Enable D28 Lineout_Mute

Pin (Panel Power) Pin Driver Pin Switch Pin Routing
[B] 3.0V (CTRLP) [B] 0.75V (OPC_CTRL) [1] 0V (Gnd) [A1] 0.06V (A_Mute)
[C] 26.85V (Out) [C] 0.02V (LED Control) [2] 0V (VCCK) [A2] 0.37V (Lineout_Mute)
[E] 30.68V (In) [E] 0V (Gnd) [3] 6.19V (3V3_EN) [C] 0.19V (Mute_Lineout)
TQ21 VGL SW Q27 RED_LED Q66 Audio_Mute D54 HDMI 5V

Pin (Panel Power) Pin Control Pin 12V Det Pin Routing
[B] 0.6V (CTRLN) [B] 0.02V (From Q17) [1] 11.7V (Off_Mute) [A1] 0.0V (HDMI_5V_In)
[C] 4.0V (SW) [C] 3.78V (LED Control) [2] 11.7V (To Q70) [A2] 5.12V ('+5VSB)
[E] 0V (Gnd) [E] 0V (Gnd) [3] -0.03V (HW_Mute) [C] 4.97V (HDMI_5V_Out)
TQ22 T-CON Q30 AMPVCC_OP Q69 Line_Out D57 HDMI 5V

Pin Write Protect Pin Regulator Pin Mute_Enable Pin Routing
[B] 0V (TCON_WP) [B] 12.71V [1] 0V (Gnd) [A1] 0.0V (HDMI_5V_3IN)
[C] 3.3V (WP1) [C] 12.78V (AMPVCC_AP) [2] 0.16V (Lineout_Mute) [A2] 0.0V (HDMI_5V_2IN)
[E] 0V (Gnd) [E] 12 06V (AMPVCC
12.06V OP)
(AMPVCC_OP) [3] -3 23V (Enable)
3.23V [C] 4 97V (HDMI
4.97V 5V Out)
(HDMI_5V_Out)
Q8 MUTE_AMP Q36 HDMI3_Hot_Swap Q70 Audio_Mute

Pin (Audio Mute) Pin Switch Pin 12V / 5V Det
[B] 0V (Mute_Amp) [1] 0V (Gnd) [1] 11.7V (To Q66)
[C] 12.63V (Mute) [2] 0V (3_HOTPLUG) [2] 12.73V
[E] 0V (Gnd) [3] 0V [3] -0.03V (Off_Mute)
Q14 LVDS_PWR Q37 HDMI3_Hot_Swap D25 Mute_Amp

Pin Driver Pin Switch Pin Routing
[B] 0.65V (LVDS_PWR_ON) [1] 0V (Gnd) [A1] 0.04V
[C] 0 04V (U21 Control)
0.04V [2] 0V (2_HOTPLUG)
(2 HOTPLUG) [A2] 0.04V
0 04V
[E] 0V (Gnd) [3] 0V [C] 0V (Mute_Amp)
Q16 BLUE_LED Q46 3V3_Enable D27 A_Mute

Pin Control Pin Driver Pin Routing
[B] 0.08V (OPWM2) [1] 0V (Gnd) [A1] 0.03V (Off_Mute)
[C] 2.56V (LED Control) [2] 0.67V (VCCK) [A2] 0.03V (HW_Mute)
[E] 0V (Gnd) [3] 0V (To Q47) [C] 0V (A_Mute)
47LV4400 Main (Front Side) Panel Voltage IC Voltages
TU1 Panel DC-to-DC TU3 PaneL

Converter Level Shifter
Pin Pin Pin Pin
[1] 4.98V (VL) [21] 26.84V (VGH) [1] 26.84V (VGH2) [13] *(-5V~26V) (VGH_EVEN)
[2] 1.49V (TCOMP) [22] 0.9V (VGL_FB) [2] -5V (VGL) [14] -5V (DISCHG)
[3] 4.98V (VL) [23] n/c [3] 26.84V (VGH1) [15] (-4.93V) (VST)
[4] 0V (Gnd) [24] 0.6V (CTRLN) [4] 8.44V (CLK1) [16] (-5V) (GIP_RST)
[5] 12.75V (P_12V)
12 75V (P 12V) [25] n/c
/ [5] 8.44V
8 44V (CLK2) [17] 0V (G
(Gnd)
d)
[6] 12.75V (P_12V) [26] 3.3V (TCON_Reset) [6] 8.44V (CLK3) [18] 7.51V (RE)
[7] n/c [27] 0V (Gnd) [7] 8.44V (CLK4) [19] 3.2V (VSENSE)
[8] 7.88V (HVDD_ SWB3) [28] 3.3V (SCL_TPS) [8] 8.44V (CLK5) [20] 0V (EO)
[9] 7.81V (HVDD_FB) [29] 3.3V (SDA_TPS) [9] 8.45V (CLK6) [21] 0V (GST)
[10] 0V (Gnd) [30] 1.8V (Vcore_FB) [10] 26.83V (VGH_R) [22] 1.13V (MCLK)
[11] 4.93V (SS) [31] 0V (Gnd) [11] -5V (VGH_F) [23] 1.62V (GCLK)
[12] 0.06V (COMP) [32] 1.8V (Vcore_Out) [12] *(-5V~26V) (VGH_ODD) [24] 3.23V (REVERSE)
[13] 0V (Gnd) [33] 3.3V (VCC_FB)
[14] 0V (Gnd) [34] n/c *Toggels every second
[15] 12.73V (SW) [35] 3.31V (VCC_SW_Out)
[16] 12.73V (SW) [36] 3.31V (VCC_SW_Out)
[17] 16 52V (SW
16.52V (SW_In)
In) [37] 0V
[18] 16.47V (VDD) [38] 12.75V (P_12V)
[19] n/c [39] 12.75V (P_12V)
[20] 30.06V (CTRLP) [40] n/c
TU2 Panel
Gamma
Pin Pin
[1] 3.3V (SDA_TPS) [11] 12.42V (GMA4)
[2] 0V (Gnd) [12] 11.36V (GMA5)
[3] 3.3V (VCC) [13] 9.86V (GMA7)
[4] 0V (Gnd) [14] 6.03V (GMA12)
[5] 6.45V (VCOM_PG) [15] 4.01V (GMA14)
[6] 6.43V (VCOM_FB) [16] 7.88V (HVDD)
[7] 15.62V (VCOM_AVDD) [17] 7.88V (HVDD)
[8] 15.62V (AVDD) [18] 3.24V (GMA15)
[9] 0V (Gnd) [19] 2.63V (GMA16)
[10] 13.05V (GMA3) [20] 3.3V (SCL_TPS)
47LV4400 Main (Back Side) Component Voltages
Q15 Controls Q41 VGA (PC) U4 3V3SV

Pin Q29 Pin Sorce Select Pin Regulator
[B] 0.68V (Ctrl) [B] 0.0V (VGA_11) [1] 2.05V (Reg)
[C] 0V (O
(Out)
t) [C] 5 0V (S1 U43 p9)
5.0V 9) [2] 3 29V (O
3.29V (Out)t)
[E] 0V (Gnd) [E] 0.0V (Gnd) [3] 5.21V (In)
Q18 HDMI Q42 RGB (PC) D11 RGB (PC)

Pin Write Protect Pin SO Switch Pin PWR Routing
[B] 0.0V (Ctrl GPIO0) [B] 0.0V (VGA_4 Mon ID) [A1] 0.58V (RGB p9)
[C] 5V (WP) [C] 5.0V (SO) [A2] 5.20V (+5VSB)
[E] 0V (Gnd) [E] 0.0V (Gnd) [C] 5V (VGA_PLUGPWR)
Q29 AV_3V3 Q71 SDA

Pin Source Switch Pin Switch
[G] 0.09V (From Q15) [G] 3.38V (DV33)
[S] 3.28V (+3V3SB) [S] 3.38V (SDA_SW)
[D] 2.27V (AV_3V3) [D] 5.0V (VGASDA_SW)
Q40 HDMI Q72 SCL

Pin HOT SWAP Pin Switch
[B] 0.0V (1_HOTPLUG) [G] 3.38V (DV33)
[C] 0.0V (HDMI p19) [S] 3.38V (SCL_SW)
[E] 0.0V (Gnd) [D] 5.0V (VGASCL_SW)
47LV4400 LVDS Waveforms TCN1 and TCN2
TCN1 PIN 28 LRLVOP TCN1 PIN 29 LRLVOP TCN1 PIN 30 LRLVOP TCN1 PIN 31 LRLVOP
TCN2 PIN 28 RMLVOP TCN2 PIN 29 RMLVOP TCN2 PIN 30 RMLVOP TCN2 PIN 31 RMLVOP
724mV p/p 764mV p/p 760mV p/p 740mV p/p
TCN1 PIN 32 LRLVOP TCN1 PIN 33 LRLVOP TCN1 PIN 26 LRLVOP TCN1 PIN 27 LRLVOP
TCN2 PIN 32 RMLVOP TCN2 PIN 33 RMLVOP TCN2 PIN 34 RMLVOP TCN2 PIN 35 RMLVOP
752mV p/p 804mV p/p 378mV p/p 350mV p/p

49UH6100 INTERCONNECT DIAGRAM 49UH6100 (2016) Interconnect
P2502 "MAIN Board" to "SMPS Board" P201
P801 "SMPS Board" To "LED Backlights"
PIN LABEL STBY RUN Diode
PIN LABEL RUN Diode
(2) 1 DRV_ON 0V 2.03V OL
No Stand-By Voltages Backlights *0% to 100%
1 LED- 78.4V~55.78V OL P201 "SMPS Board" To P2502 "MAIN Board"
Pins 2, 4, 6 are n/c. (3) 2
Pins 3-5 shorted P_DIM#1 0V *0.18V-3.24V OL
3 LED+ Pins 3 and 5 are jumped together PIN LABEL STBY RUN Diode (1) PWR-On Pin 1: Turns on 13.2V to the Main. No
together on SMPS OL Direct Lit Backlights (LED Array Strips) backlights at this time. Backlight Power is 160.8V. 3-4 Gnd Gnd Gnd Gnd
5 LED- 123.7V~109.4V (3) 12 P_DIM1 0V *0.18V-3.24V OL
36 Total LEDs. 4 Strips with 9 LEDs per/strip. (2) MS 5-8 13.2V 7.90V 13.11V OL
7 LED+ 169.0V~163.6V OL (2) 11 MS (Drv_On) 0V 2.03V OL (DRV_On) Pin 11: Turns on the Backlights.
Backlight power goes to 169V.
9-10 Gnd Gnd Gnd Gnd 9 Gnd Gnd Gnd Gnd
In Out Dim to Bright
(3) P_DIM#1 Pin 12 and P_DIM#2 Pin 2: Will vary
4-8 13.2V 7.90V 13.11V OL 10 13.2V 7.90V 13.11V OL
according to incoming video IRE level and OSD Backlight
To Panel Backlights (Dim to Bright) 3 Gnd Gnd Gnd Gnd (1) 11 PWR_ON OL
setting Output from the Video Processor. It is then routed 0V 3.29V
Backlight Power 169.0V~163.6V pin 7
(3) 2 N/C n/c n/c n/c out P2300 to P201 and sent to the LED Driver IC on the
Pin 1 goes to Backlight Driver Q801 (Back of SMPS) 12 N/C n/c n/c n/c
Back of the SMPS.
(1) 1 PWR_ON 0V 3.29V 0.87V The Range is: 0.18V~3.24V. *0% to 100%
*Dim to Bright
P801
D802
D803
Gnd Can not use Smart Test Jig on

L801
D201
JTAG RS232C_Debug
13.12V this model for SMPS test mode. SW300 P100 n/c
Gnd 0
Backlight P1 n/c
Power IC2500
Gnd +5V_Normal
D204
D206
D205
IC2301
D202
D203
13.12V +1.8V
80V Gnd
T101 IC102 IC103 C E
Q2500
IC102 IC100
B
1) 11.54V 1) 1.10V PWR_ON
IC103
Secondary P201 Chassis 2) 10.52V Chassis 2) 0V E B MAIN BOARD
Gnd Gnd C
Q2503
Video
Processor Main Board
SMPS Hot Hot E B
23.40V Q2504 p/n: EBT64138309

D107 Gnd 3) Hot Gnd Gnd 3) 16.87V
C
Panel_VCC AUSWLOR
P/N: EAY64388811 4) 1.50V 4) 20.96V p/n: EBT64237702
LVDS Cable
BUSFLJR / BUSFLOR
D101 Can’t Read p/n: EAD63787803
To T-CON
3.15A / 250V p/n: EBT64138308
Run: 400V D602 BUSWLOR
D109 STBY: 186.7V
USB
F101
200V 400V TO MAIN (1.81V)
CN1 (3.28V) (Gnd)
+
Warning Do Not Use Jig JK4400

C611
460V
68uF
T-CON comes with the Panel VIN: (PANEL_VCC 12V)

107.2V Caution: Make sure the screws are installed when the LVDS Pins 1-8 (11.97V)
From Main
U4 IC4400
CN1
-
CX101 T-CON is operating, damage may occur without them.

Panel_VCC Supply (1.81V) P101 RS232
n/c Audio
+5V_USB_2
106V D601 (3.29V)
Gnd 23 Gnd
(12.90V) B HDMI 2 HDMI 3 IC11200
L601
B C
(7.70V) VCC E C E
F1 (VIN) Q3001
HVDD SPK Ft Right Q5800
LF103
TH101
Vcore R111 F1 5A/125V

CX102
D1 (1.20V) p/n: EAB64048602 IC5800

FL3 FL2 JK3301 JK3300
LF101 34
3 1
81
(-7.05V)
4
1 1
VGL1 SPK Ft Left
5 7 4
4
U5 5
7
U1 U4 Composite/Component Audio TU6700
BD101
6
D3 p/n: EAB64048601
5
TDJS-H301F
AC
1
15 6
R- R+ L- L+
F100 LF102
2
D2
9
UC1
U3 Q3
11 JK3302
5A / 250V VGH VGL2
GCLK
10Mhz
RS1 VCC18 (1.81V)
To Speakers P5800
(28.09V) (-7.05V)
HGnd
HDMI 1
MCLK VDD
VST
GST
EQ (-7.01V ~ 28.09V)
(15.84V)
Source
All Speaker IC4100 Optical
8 1
VDD JK5000 Serv Only Access
8 8
1 3
+3.5V_WIFI
(-7.01V) 9
3 3 VGH-ODD VGH-EVEN
plug pins Tuner pins Q3302
B C
CN2
2
VGH-ODD and VGH-EVEN 1
CN3
E
LAN From the

Toggles between
1.44V
SK100 AC 5
1 1
0 5
2 2
0 5
3 3 4
0 5 0
4 5 5 6
5 0 5 0
29.09V to -7.05V every
second.
5
1
0
1 2 2
5 0 5
3 3 4 4 5 5
0 5 0 5 0 5
6
0
Diode Check (OL) P4100 JK3801 JK3800
back side. HDMI 1
Hot Swap
CN2 Key Voltages To the Panel To the Panel CN3 Key Voltages
All 6 screws are M3X5L (Silver) Vcore Pin 33 RS1 Vcore Pin 28
1.63Vdc
VCC18 Pin 34, 35 3.72V p/p VCC18 Pin 26, 27
U1
SMPS TEST: Forcing SMPS On. Hot Gnd HVDD Pin 36 Top Legs HVDD Pin 25
Pin 1 Gnd
KEY VOLAGES
This test requires simple 3V jig. See below.. (Shock Hazard) VDD Pin 37-40 1.56Vdc
3.58V p/p
VDD Pin 21-24 Pin 2
Pin 3
Gnd
Gnd
P4000 "MAIN" to "Joy Stick, WiFi"
VGL1 Pin 45 Bottom Legs VGL1 Pin 16
Pin 4 Gnd
VGH_EVEN Pin 49 VGH_EVEN Pin 12 Pin 5
PIN LABEL STBY RUN Diode Check
3.27V
Pin 6 3.26V
Remove AC Power. VGH_ODD Pin 50 CLK1 – CLK8
32.8V - 33.0V p/p
GCLK
3.56V p/p
MCLK
3.60V p/p
GST
3.24V p/p
VGH_ODD Pin 11 Pin 7 3.29V
Pin 8 3.30V
Disconnect P2502 on Main Board. VGH Pin 51 VGH Pin 10
1 3.5V_WiFi 0V 3.37V OL
Test 1: Using a 3V jig, Jump 3V to pin 1 (PWR_ON). P201 Note: 15 IR 3.39V 3.37V 1.83V
Apply AC Power. (No Backlights in Test 1) All have similar
Test 2 11 12 P201 still inserted. P2502 removed. waveforms EQ: No Waveform
(Pins 4-8) rises to 13.14V. 18 3.5V_ST 3.41V 3.40V 1.12V
Use P2502 side to insert resistors. PANEL TEST: ROLLING TEST PATTERNS
2 AA (3V)
Backlight Power 160.8V.

Note: 7.90V (Pins 4-8) 1) With no Power, remove CN1 (Vx1 Cable) 19 Key 2 3.41V 3.40V 1.86V
Remove AC Power. P_DIM will be 10.12V
Must be present when AC is applied before 2) Jump 12V from SMPS to Fuse F1.
Front IR/Joy Stick WiFi
beginning test indicating Standby is OK. For 12V from SMPS use D202 (center leg) Top right hand heat sink.
Test 2: Using a 3V jig, Jump 3V to pin 11 3 Ground: Pins 4, 6, 8, 14, 17, 20, 21
3) Jump VCC (3.3V) to pin 23 of CN1. For easier contact to pin 23, use top side of R111.
(DRV_ON). No Connection (Not Used): Pins 9, 10, 11
Apply AC Power. All Voltages should be produced. Test 1 3V JIG: Made from 2 (AA) batteries.
1 2 SMART JIG: Other Pin Functions: WiFi_DM 0.03V pin 2,
(13.14V to Main and 149.7V to the Backlights). Jump + to – on one side.
This will also force the Backlights to come on. Test Set Up On the other side, solder two red wires Can not run normal Panel Test by removing Vx1 cable on T-CON and supplying 12V to WiFI_DP 0.03V pin 3, WOL_PWR_On 0V pin 5,
(needle tipped) to the + and one black wire T-CON fuse. It will not work. Can not use Smart Test Jig on this model for T-CON test. M_Reset 0V pin 7
P_DIM will be 10.12V Bottom Center of Set Bottom Right (Rear View)
(needle tipped) to the – side. Front IR WiFi Module SDA 3.41V pin 12, SCL 3.41V pin 13
p/n: EBR78925201 p/n: EBR78925201
October 2016 Page 01 LG

LG
2015 Direct View UHD Training
55UF7600 WebOS 2.0 UHD LCD TV
MAIN BOARD INFORMATION
Main Board Layout

y and
Voltage Measurements
55UF7600 Main Board (Photo) 55UF7600 (2015) Main Board Section
September 2016 Page 01

LG
55UF7600 Main Board Component Layout 55UF7600 (2015) Main Board Section 08
Heatsink Clip
P2300 "MAIN Board" to "SMPS Board" P201 X1900
LD12900: Indicates VX1 Signal to (24MHz)
T-CON is good if LD12900 is illuminated. Q12900
IC13408
PIN LABEL STBY RUN Diode Check B
+1.1V_U_VDDC
If Off, possible causes:
C
LD12901 E
23-24 GND Gnd Gnd Gnd Improper seated or defective Vx1 cable IC1901 N/C
or problem with signal processing. LD1900
IC2500 DDR P1905
18-22 24V 0V 25.46V OL
B E
IC2600 CORE_VIDO Selector

LD12901 turned on by Q12900
URSA9
C D
Q1901 G S
Q2500
16-17 GND Gnd Gnd Gnd DDR
Note: With top 3 screws left out of the SPI FLASH IC2700
IC2501 CORE_VID1 Selector
11-15 12V 0V 11.88V OL board, video looks double image like it's +1.5V_U_DDR Q2501
D
IC2900 IC2800
in 3D.
G S
9-10 GND Gnd Gnd Gnd DDR DDR IC13403 +1.1V_VDDC
7-8 3.5V 3.54V 3.52V 1.23V

DDR_VTT_URSA
Heatsink
6 GND Gnd Gnd Gnd IC13100 Clip
IC407
5 3.5V 3.54V 3.52V 1.23V
Q402 M2_DDR_RESET_N
P7100 DDR_VTT_1 IC405 IC406 M13507 +5V_Normal
To the IC2303 Q402 DDR DDR +3.3V_Normal USB_+5V
4 P-DIM2 0V 0.92V OL IC201
T-CON 1
2
3
IC2305
Q7100 I2C_SCL6 Buffer
3 P-DIM 0V 0.17V-2.55V OL +1.5V_DDR AVDD_3P3 IC200
Q7101 I2C_SDA6 Buffer 13.2V IC2302
Q7102 HTPDAn Driver Pins 48-51 +3.5V_WOL
Q7101 FET
2 DRV_ON 0V 3.46V 1.54V Q7103 LOCKAn Driver Q7100 FET Processor X600
Q7104 HTPDAn Switch (24MHz)
Q7102 Q7104 IC4300
Q7105 LOCKAn Switch
1 PWR_ON 0V 3.51V OL Q7103 Q7105
+5V_USB_3
IC2307 12V
Dim to Bright PWR_Det IC2307
2
3
1
IC600 DDR IC100 JK4300
Panel_VCC
USB3
(1) PWR_ON: turns on the 12V and 24V lines.
Backlight power goes to 63.62V. IC2309 IC602 DDR
IC2300 Q2302 CPU_VID1 Select
(2) INV_CTL: (DRV_ON on SMPS) turns on the IC2300 Q401
Q400 Q400 M0_DDR_RESET_N Select
D
+1.1V_VDDC_CPU Q2301 Q2302

DDR-VTT
C
Backlights. Backlight power goes to 80V.

G S
Q2321 E B
IC8100
USB2
Q401 M1_DDR_RESET_N Select IC402 B E
C
(3) P-DIM: controls the backlight brightness. Controlled
IC401
IC400
by Cust. Menu, Video, Backlights. Range 0% to To P2300 In
MEMC
JK4302
+1.8V Out /FRC
SMPS IC2301 JK4500
100% directly proportional to DC voltage to Backlight
Adj
Q2300 3 1 Q2300 IC102

brightness. P-DIM is actually a PWM signal. Head Phone Amp
USB1
2
PWR_ON NVRAM
(4) P-DIM2: Fixed Voltage. X3000 RS232 P101 Main Board
X3000
P3000
IC6100 Optical p/n: EBT63818912 AUSYLJR
(32.768KHz) IC3000 p/n: EAJ63109901 BUSYMJR
KEY VOLAGES IC6801 JK5000 JK3803 JK3800
Q3001 D
S
G
p/n: EAY63729101 BUSYLJR
P4100 "MAIN" to "Joy Stick J1, M-Remote/WiFi" CEC Q3001 LAN
p/n: EBT63990602 AUSYMJR
Micro
HDMI3
SW3000 p/n: EBT63990603 AUSYMJR
PIN LABEL STBY RUN Diode Check Micom Reset SW3000 JK3801
Head
Q5800 Mute RS232
2 3.5V_WOL 0V 3.49V OL WiFi pin 1 E B
Phone JK3203
C TUNER PINS
12 Key 1 3.55V 3.52V 1.98V Joy Stick pin 2 IC5800 TU_CVBS
9. CVBS
HDMI2
Audio MAIN BOARD Q6502 8. SIF
14 Key 2 3.55V 3.52V 1.98V Joy Stick pin 3 TU6705 C
7. DIF (N)
B E
9 JK3200 6. DIF (P)

15 IR 3.54V 3.78V 1.89V Joy Stick pin 7 +3.5V_WiFi
TDJH-H301F
TUNER
Access Tuner JK3202 5. SDA_RF
pins from the 1 Hot 4. SCL_RF
16 3.5V_ST 3.56V 3.52V 1.25V Joy Stick pin 4 IC4100 TU6401
back
Swap
HDMI1
side 3. DIF AGC
Pin 2 is power for the M-Remote / WiFi Board

P5800 JK3802
B
E
C
2. N/C
1. +3.3V_LNA_TU
Q3300
Pin 16 is power for the IR/Joy Stick Board P4100
P4000
IR peak/peak 3.80V
All Speaker plug pins To
(Min) 2.83V-3.20V (Max) Ft. Joy Stick /
Diode Check (OL) IR
September 2016 Page 02 LG
55UF7600 Main Board Crystals Measurements 55UF7600 (2015) Main Board Section
X1900
(24MHz)
Top Right
2.92V / 25nSec
X1900 Top Right Leg P/P
1.35VDC 2.92V p/p
Bottom Left Leg Bottom Left

3.6V / 25nSec
24Mhz 1.42VDC 3.6V p/p
X600 Top Left

(24MHz) 3.04V / 10nSec
X600 Top Left Leg P/P Bottom Right

3.72V / 10nSec
1.70VDC 3.04V p/p
Bottom Right Leg
24Mhz 1.68VDC 3.72V p/p
Right Leg
X3000 1.08V / 10uSec
X3000 Right Leg P/P

Left Leg
0.68VDC 1.08mV p/p 856mV / 10uSec
Left Leg
24Mhz 0.15VDC 856mV p/p
September 2016 Page 03 LG

55UF7600 (2015) Main Board Section
55UF7600 Main Board (Small) Component Voltages
Pin Memory Pin Regulator Pin Regulator Pin LD1900 Pin Driver
[1] Gnd [1] Gnd [1] 3.49V (Out) [E] 0.67V [B] 0V
[2] Gnd [2] 11.85V (Vcc In) [2] Gnd [B] 0.52V [C] 3.29V
[3] Gnd [3] Gnd [3] 0.43V (n/c) [C] Gnd [E] Gnd
[4] Gnd [4] 0.80V (FB) [4] 3.51V (En)
[5] 3.30V [5] 1.36V (Comp) [5] 3.51V (Vcc In) Q2300 PWR_On Q6502 TU_CVBS
[6] 3.30V [6] 3.47V (Enable) Pin Switch Pin Buffer
[7] Gnd [7] 1.07V (Out) IC4300 +5V_USB_1 [1] 3.50V [B] 1.52V
[8] 3.30V [8] 1.07V (Out) Pin Regulator [2] 2.84V [C] Gnd
[1] 5.11V (In) [3] 3.49V [E] 2.23V
IC200 +3.5V_WOL IC2301 +1.8V_DDR [2] Gnd
Pin Regulator Pin Regulator [3] 3.28V (Enable) Q2301 CPU_VID0 Q7100 I2C_SCL6
[1] 3.49V (Out) [In] 3.29V (In) [4] 3.30V (USB_OCD3) Pin Select Pin Switch
[2] Gnd [Out] 1.79V (Out) [5] 0.40V [G] 0.31V [G] 3.05V
[3] 0.17V n/c [Adj] 0.54V [6] 5.11V (Out) [S] Gnd [S] 3.27V
[4] 3.51V (WOL_CTL) [D] 0.07V [D] 3.26V
[5] 3.50V (Vcc In) IC2302 (+3.3V_NORMAL) IC13100 DDR_VTT_URSA
Pin Regulator Pin Regulator Q2302 CPU_VID1 Q7101 I2C_SDA6
IC201 AVDD_3P3 [1] Gnd [1] 1.52V (In) Pin Select Pin Switch
Pin Regulator [2] 11.82V (Vcc In) [2] Gnd [G] 3.29V [G] 3.05V
[1] Gnd [3] Gnd [3] 0.76V [S] Gnd [S] 3.27V
[2] 3.31V (Out) [4] 0.70V (FB) [4] 0.76V (Out) [D] 0.07V [D] 3.26V
[3] 3.50V (In) [5] 1.97V (Comp) [5] n/c
[6] 3.47V (Enable) [6] 3.29V (Enable) Q2321 Driver for Q7102 HTPDAn
IC402 DDR_VTT [7] 3.31V (Out) [7] n/c Pin IC2309 Pin Driver
Pin Switch [8] 3.31V (Out) [8] n/c [B] 0.66V [G] 0.18V
[1] 1.51V (in) [E] Gnd [S] 0.0V
[2] Gnd IC2303 +1.5V_DDR IC13403 (+1.5V_U_DDR) [C] 0.60V [D] 1.96V
[3] 0.76V Pin Regulator Pin Regulator
[4] 0.76V (out) [1] 3.40V (Enable) [1] 3.49V (Enable) Q2500 CORE_VIDO Q7103 LOCKAn
[5] n/c [2] 0.76V [2] 0.77V Pin Select Pin Driver
[6] 3.29V (Enable) [3] 5.23V [3] 5.23V [G] 3.31V [G] 0.18V
[7] n/c [4] 2.49V [4] 2.51V [S] Gnd [S] 0.0V
[8] n/c [5] Gnd [5] Gnd [D] 0.07V [D] 1.97V
[6] 1.57V (Out) [6] 1.53V (Out)
IC407 DDR_VTT_1 [7] 6.60V [7] 6.47V Q2501 CORE_VID1 Q7104 HTPDAn
Pin Switch [8] 11.84V (Vcc In) [8] 11.84V (In) Pin Select Pin Switch
[1] 1.52V (in) [G] 3.31V [G] 0.63V
[2] Gnd IC2307 PWR_Det Q400 M0_DDR_RESET_N [S] Gnd [S] 0.0V
[3] 0.76V Pin 12V Sense Pin Select [D] 0.07V [D] 0.04V
[4] 0.76V (out) [1] Gnd [E] Gnd
[5] n/c [2] 3.61V (Out) [B] 0.0V Q3001 CEC Q7105 LOCKAn
[6] 3.29V (Enable) [3] 3.64V (In) [C] Do Not Measure Pin Bi-Directional Pin Switch
[7] n/c [G] 3.51V [G] 0.0V
[8] n/c Q2309 Panel_VCC Q401 M1_DDR_RESET_N [S] 3.48V [S] 0.64V
Pin Switch Pin Select [D] 3.43V [D] 0.05V
IC1901 SPI FLASH [1] 11.85V (Vcc In) [E] Gnd
Pin Memory [2] 11.85V (Vcc In) [B] 0.64V Q3300 HDMI Q12900 Drives
[1] 3.29V (CS) [3] 11.85V (Vcc In) [C] 0.07V Pin Hot Swap Pin LD12901
[2] 3.28V (SO) [4] 1.86V (CTL) [B] 0V [E] 0.63V
[3] 0V (WP) [5] 11.84V (Out) Q402 M2_DDR_RESET_N [E] Gnd [B] 0.02V
[4] Gnd [6] 11.84V (Out) Pin Select [C] 0.63V [C] Gnd
[5] 3.29V (SPI_DI) [7] 11.84V (Out) [E] Gnd
[6] 0V (SPI_CK) [8] 11.84V (Out) [B] 0.0V
[7] 3.29V (Hold) [C] 1.56V
[8] 3.29V (In)

55UF7600 (2015) Main Board Section
55UF7600 Main Board (Large) Component Voltages
IC2305 IC3000 IC5800

+5V_NORMAL / +5V_USB Micro Audio
Regulator Pin Processor Pin Pin Amp Pin
Pin Pin [1] 3.23V [25] 0V [1] n/c [21] 2.16V (Out R+)
[1] 25.35V (In) [15] 3.43V (OCP2) [2] 3.23V [26] 3.51V [2] 1.24V [22] Gnd
[2] 25.35V (In) [16] 5.11V [3] 2.69V [27] 3.51V [3] n/c [23] 4.71V
[3] 25.35V (In) [17] 5.11V [4] 2.09V [28] 0.03V [4] Gnd [24] 5.12V
[4] Gnd [18] 11.53V [5] 3.46V [29] 0.1V [5] n/c [25] 5.14V
[5] Gnd [19] 5.11V (Out) [6] 3.5V [30] 0V [6] 1.26V [26] n/c
[6] Gnd [20] 5.11V (Out) [7] 3.49V [31] 3.34V [7] 0V [27] 5.11V
[7] 6.30V [21] 5.11V (Out) [8] 3.51V [32] 3.51V [8] 1.62V [28] 4.72V
[8] 6.30V [22] 1.94V [9] 0V [33] 3.51V [9] n/c [29] Gnd
[9] 3.51V (Enable) [23] 0.60V [10] 3.51V [34] 3.75V [10] 2.62V [30] 2.16V (Out L-)
[10] 5.10V (Out USB2) [24] 0.35V [11] 3.51V [35] 0V [11] 2.43V [31-32] 18.67V (L B+)
[11] 5.10V (Out USB3) [25] 1.24V [12] 0V [36] 0V [12] 3.30V (Mute) [33] 2.16V (Out L+)
[12] 3.28V (USB2 Ctrl) [26] 0.45V [13] 3.51V [37] 0.02V [13] n/c [34] Gnd
[13] 3.28V (USB3 Ctrl) [27] 0.45V [14] 3.72V [38] 0V [14] 0.0V [35] 4.71V
[14] 3.43V (OCP2) [28] Gnd [15] 3.53V [39] 3.51V [15] n/c [36] 3.03V (Reset)
[16] 0V [40] 3.51V [16] 4.71V [37] Gnd
IC2501 [17] 3.51V [41] 0.65V [17] Gnd [38] 1.61V
+1.1V_VDDC [18] 3.51V [42] 0.13V [18] 2.16V (Out R-) [39] Gnd
Pin Regulator [19] 3.29V [43] 0V [19-20] 18.67V (R B+) [40] 3.31V (In)
[1] 3.51V (EN) [9] 11.83V (In) [20] 3.09V [44] 0.14V
[2] 0 43V (Freq)
0.43V [10] Gnd [21] 3 06V
3.06V [45] 0V
[3] 0.63V (FB) [11] Gnd [22] 0V [46] 2.09V IC13408
[4] 4.84V (SS) [12] Gnd [23] 0V [47] Gnd +1.1V_U_VDDC
[5] Gnd [13] Gnd [24] 0.1V [48] 3.51V Pin Regulator
[6] 4.83V (PG) [14] 11.83V (In) [1] 3.51V (EN) [9] 11.83V (12V In)
[7] 4.87V (VCC) [15] 1.02V (Out) IC6801 [2] 0.43V (Freq) [10] Gnd
[8] 5.79V (BST) [16] 1.02V (Out) RS232 [3] 0.63V (FB) [11] Gnd
Pin Data [4] 4.84V (SS) [12] Gnd
IC6100 [1] 3.52V [9] n/c [5] Gnd [13] Gnd
Head Phone [2] 5.39V [10] n/c [6] 4.83V (PG) [14] 11.83V (12V In)
Pin Amp Pin [3] 0V [11] 3.09V [7] 4.87V (VCC) [15] 1.18V (Out)
[1] Gnd [8] 1.66V [4] 0.02V [12] 3.52V [8] 5.95V (BST) [16] 1.18V (Out)
[2] 0V (R In) [9] 3.31V (3.3V_Normal In) [5] (-5.33V) [13] 0V
[3] 0V (R Out) [10] Gnd [6] (-5.34V) [14] (-5.24V)
[4] Gnd [11] n/c [7] n/c [15] Gnd
[5] 3.49V (Mute) [12] 0V (L Out) [8] n/c [16] 3.52V (3.5V_ST In)
[6] (-3.18V) [13] 0V (L In)
[7] (-1.59V) [14] Gnd

LG
2016 4K UHD Training
65UH5500 WebOS 3.0 4K UHD TV
MAIN BOARD LAYOUT
((Main Circuit Board Layout)

y )
65UH5500 Main Board Picture 65UH5500 (2016) Main Section
P2501
To Inverter
MAIN BOARD
EBR82959601
P1 N/C
USB
HDMI 3
P7100
To T-CON
HDMI 2
P101 N/C
HDMI 1
P4100
To IR/Joystick
and WiFi
P5800 RF In
To Speakers
HP
Optical LAN
Component/Composite Audio
March 2017 Page 01

LG
65UH5500 Main Board Component Layout 65UH5500 (2016) Main Board Section
To Inverter Heat Sink is Not Removable

P5201 Main to Inverter CN402 JTAG
Pin Label STBY Run Diode P2501 P1 N/C
1 PWR_ON 0.0V 3.20V OL
3
2 N/C n/c n/c n/c
2 1
+5V_Normal JK4400
3 Gnd Gnd Gnd Gnd Q2500
IC2500
4-8 13.2V 10.48V 13.34V OL PWR_ON
USB
9-10 Gnd Gnd Gnd Gnd
Q2503 IC100
11 DRV_ON 0V 3.36V 1.91V
E B
C
(Drives Q2504) LGE6551-CA1 +5V_USB_2
12 P_DIM 0V 0.16V – 3.36V OL IC2301
S G
+1.5V_DDR Video Processor
Q2504
(Dim to Bright) D
+1.8V IC4400
Panel_VCC IC2303
Note: Backlight Power is 64.4V in STBY.
HDMI 1
(1) PWR_ON = (STB) Pin 1: Turns on the Power
JK3302
Supply. Backlight power goes to 84.6V.
Backlights are not on at this time. To T-CON P7100 D3309
C
A2 A1 B
C
(2) DRV_ON (Pin 11): Turns on the Backlights. (I2C_SCL6 Buffer) E
HDMI 1 Q3302
Q7100
G
D
Backlight power goes to 78V. Note: P_DIM Must S
Hot Swap
G
also be active. (3.3V) Max Brightness. S
D
Q7101
(Pulse Width Modulation Dimming).
HDMI 2
(I2C_SDA6 Buffer)
(3) P_DIM (Pin 12) = Controls the backlight 13V to T-CON MAIN BOARD JK3300
brightness. Controlled by Cust.: Menu --> Video -- Pins 44-51
C
D3305
> Backlights and by average brightness levels of P101 A2 A1 B
C
Main Board
E
n/c HDMI 2
the Video content. Q3301
RS232C p/n: EBR82959601 Hot Swap
Range 0% to 100% directly proportional to DC
voltage to Backlight brightness. (0.16V~3.36V)
HDMI 3
P-DIM is actually a PWM 4.76V p/p signal. +3.5V_WIFI JK3301
To IR and
Joystick
IC4100 D3308 Q3300

IC200 ST_A1V0
IC101 C
A1
A2
B
C
P4100 HDMI 3
E
Q5800 Memory Hot Swap

E B
Mute
All Speaker plug pins C IC11200
To Speakers
IC5800 11 1
R- R+ L- L+
1.8V TU6700
P5800
Diode Check (OL) RS232 Tuner

JK5000
KEY VOLAGES
P4100 "MAIN" to "Joy Stick, WiFi" Audio JK3801 JK3803 Access Tuner pins
JK3808 JK3809 From the back side.
Optical
PIN LABEL STBY RUN Diode Check LAN

HP
2 3.5V_WiFi 0V 3.42V OL Component / Composite Audio

10 Key 2 3.44V 3.43V 1.86V
11 IR 3.42V 3.42V 1.73V
12 3.5V_ST 3.44V 3.44V 0.92V
P4100 "Main" WiFi Board P4100 "MAIN" IR Board
Pins 1, 5, 14: Ground Pin Pin Pin Pin
Pins 7, 8, 9: No Connection (Not Used) 1 6 10 1
Pin 3: WOL_PWR_On 0.24V IR Signal 2 1 11 2
Pin 10: Key2: 0.59V when Power Button Pressed 3.76V p/p 3 5 12 5
Pin 11: IR: 2.99V when IR Received 4 2 13 3
Pin 13: LED_R (0V) LED Off/TV On. (3V) LED On/TV Off. 10mSec / 1V 5 4 14 4
6 3
March 2017 Page 02 LG

65UH5500 (2016) Main Board Section
65UH5500 Main Board IC Voltages
IC101 NVRAM IC2303 +1.5V_DDR IC4100 +3.5V_WiFI IC5800 Audio
Pin Memory Pin Regulator Pin Regulator Pin Amp Pin
[1] Gnd [1] 3.44V (In 3.5V_ST) [1] 3.44V (In 3.5V_ST) [1] n/c [21] 1.81V (SPK_R+)
[2] Gnd [2] 3.44V (In 3.5V_ST) [2] Gnd [2] 1.29V (VDD_PLL) [22] Gnd
[3] Gnd [3] Gnd [3] 3.44V (EN) [3] n/c [23] 6.38V
[4] Gnd [4] Gnd [4] 0.03V (OC) [4] Gnd [24] 5.11V
[5] 3.42V (SDA) [5] Gnd [5] 0.19V [5] n/c [25] Gnd
[6] 3.22V (SCL) [6] 0.83V (FB) [6] 3.34V (Out) [6] 1.24V (DVDD) [26] n/c
[7] Gnd [7] 0.34V (ITH) [7] 1.40V (SDATA) [27] 5.09V
[8] 3.40V (In +3.3V_Normal) [8] 0.0V IC4400 +5V_USB_2 [8] 1.79V (WCK) [28] 6.33V
[9] 2.26V (SS) Pin Regulator [9] n/c [29] Gnd
IC200 ST_A1V0 [10] 1.53V (Out) [1] 5.02V (In +5V_Normal) [10] 3.42V (SDA) [30] 1.81V (SPK_L-)
Pin Regulator [11] 1.53V (Out) [2] Gnd [11] 3.42V (SCL) [31] 13.2V (13V_AMP In)
[1] 3.44V (EN) [12] 1.53V (Out) [3] 3.40V (EN) [12] 3.37V (Mute) [32] 13.2V (13V_AMP In)
[2] Gnd [13] 5.06V (Boot) [4] 3.39V (OC) [13] n/c [33] 1.81V (SPK_L+)
[3] 0.79V (ADJ) [14] n/c [5] 0.40V (ILIM) [14] n/c [34] Gnd
[4] 3.44V (In 3.5V_ST) [15] 3.49V (EN: POWER_ON/OFF2_3) [6] 5.03V (Out) [15] n/c [35] 6.40V
[5] 1.0V (Out) [16] 3.44V (In 3.5V_ST) [16] 0V [36] 3.33V (AMP_Reset)
IC11200 RS232 [17] Gnd [37] Gnd
IC2301 +1.8V IC2500 +5V_Normal Pin Data Buffer [18] 1.81V (SPK_R-) [38] 1.08V (AUD_SCK)
Pin Regulator Pin Regulator [1] 3.31V (C1+) [19] 13.2V (13V_AMP In) [39] Gnd
[1] n/c [1] 3.44V (EN: POWER_ON/OFF1) [2] 5.52V (V+) [20] 13.2V (13V_AMP In) [40] 3.3V (+3.3V_Normal)
[2] 3.44V (EN Power_On/Off2_2) [2] 0.77V (FB) [3] 0V (C1-)
[3] 3.39V (In +3.3V_Normal) [3] 5.07V (VREG5) [4] 0V (C2+)
[4] 5.03V (Bias) [4] 4.86V (SS) [5] (-5.43V ) (C2-)
[5] 0.60V (SS) [5] n/c [6] (-5.46V ) (V2-)
[6] 1.80V (Out) [6] +5.03V (Out) [7] (n/c)
[7] 0.60V (FB) [7] +5.03V (Out) [8] (n/c)
[8] Gnd [8] 9.72V (Boot) [9] (n/c)
[9] 13.2V (In +13V) [10] (n/c)
Q2500 PWR_On [10] 13.2V (In +13V) [11] 3.27V (DIN2)
Pin Switch [12] 3.3V (ROut1)
[1] 3
3.45V
45V (In) Q7100 [13] 0V (RIn1)
[2] 279V Q7101 I2C_SCL6 Buffer [14] (-5.46V ) (DOut1)
[3] 3.43V (Out) Pin I2C_SDA6 Buffer [15] 0V (Gnd)
[G] 3.42V (T_CON_EN) [16] 0V (In) +3.3V_ST
Q2503 Drives (Controls) Q2504 [S] 3.14V (Out)
Pin (Panel_VCC) [D] 3.39V (In) Q3301
[B] 0.62V (PANEL_CTL) Q3302 HDMI-2 Hot Swap (Pin 19 JK3300)
[C] 0.05V Q5800 Audio Mute Pin HDMI-1 Hot Swap (Pin 19 JK3302)
[E] Gnd Pin ("C" To pin 12 IC5800) [B] 0V (HDMI_HPD_CBUS_1)
[B] 0.0V (AMP_MUTE) [C] 0V (5V_DET_HDMI_1 and 2)
Q2504 Panel_VCC [C] 3.37V (Low Active) [E] Gnd
Pin Switch [E] Gnd
[G] 10.57V
[S] 13.13V (+13V_In)
[D] 13.08V (Out)
March 2017 03
5 4 3 2 1
TP_TCON RN260 3.3V

TP 8
3
100R
2 MFIO_15 RN263 1k 1 VN5
MAIN1V2 MMBT3904LT1
RN29 RESET
2
VDD_12
10k
BMLV_4P 8
AMLV_CKN
BMLV_CKN
BMLV_1P
BMLV_1N
8
BMLV_3N8
CN34
AMLV_CKP
BMLV_CKP
8
BMLV_5N8
AMLV_1N
AMLV_3N8
AMLV_1P
AMLV_0N
AMLV_2N
AMLV_4N
AMLV_5N
BMLV_0N
BMLV_2N
BMLV_4N
8
8
8
8
AMLV_0P
AMLV_2P
AMLV_3P
AMLV_4P
AMLV_5P
BMLV_0P
BMLV_2P
BMLV_3P
BMLV_5P
8
8
CN33 RN32 RN30
RSTN PI
100n/16V 100p/50V
VDD_MLVDS_33
VDD_MLVDS_33
0R/NC 12k/1%
VDD_MLVDS_33
VDD_IO_33
D VDD_LVDS_12 D
CN30 RN231 PI Resistor Must Close IC Pin
CN35 CN36 1u/10V 100R/1%
AMLV_CKP
BMLV_CKP
AMLV_CKN
BMLV_CKN
100n/16V
AMLV_0P
AMLV_1P
AMLV_2P
AMLV_3P
AMLV_4P
AMLV_5P
BMLV_0P
BMLV_1P
BMLV_2P
BMLV_3P
BMLV_4P
BMLV_5P
AMLV_0N
AMLV_1N
AMLV_2N
AMLV_3N
AMLV_4N
AMLV_5N
BMLV_0N
BMLV_1N
BMLV_2N
BMLV_3N
BMLV_4N
BMLV_5N
100p/50V
2
MFIO_13
VDD_DDR_33R
PI
MAIN3V3
CN1
VDD_IO_33
M2
M6
M1
M5
G1
G2
G3
U2
U3
R1
R2
R3
N2
N1
N3
H2
H1
H3
D2
N5
D1
P2
P3
E2
E1
E3
Y8
T2
T1
T3
F2
F3
L2
L1
J2
J3
NN1B 100n/16V
CN114 CN107 RN170 NC/0R GPO_5
GPO_5
3.3V_VCCIO-Y8
BMLV_5P
BMLV_4P
BMLV_3P
GNDAM_MLVDS-M2
BMLV_CKP
BMLV_2P
BMLV_1P
BMLV_0P
GNDAM_MLVDS-L2
AMLV_5P
AMLV_4P
AMLV_3P
AMLV_CKP
GNDAM_MLVDS-L1
AMLV_2P
AMLV_1P
AMLV_0P
BMLV_5N
BMLV_4N
BMLV_3N
3.3V_MLVDS_VCCAM-M6
BMLV_CKN
BMLV_2N
BMLV_1N
BMLV_0N
3.3V_MLVDS_VCCAM-M5
AMLV_5N
AMLV_4N
AMLV_3N
AMLV_CKN
PI
3.3V_MLVDS_VCCAM-N5
AMLV_2N
AMLV_1N
AMLV_0N
100n/16V RN168 NC/0R POL_TCON
100p/50V 5,8 GSEL POL_TCON 5
RN173 NC/0R
VDD_MLVDS_33
RN174 0R GPO_5
CN118 CN86 7 Terminate T7 B1 BIST
VDD_12 H5 GND-T7 BIST B2 LVDS_TYP_TCON
RN162 0R STV_D_TCON 1.2V_VCC-H5 LVDS_TYP
100n/16V 7 STV VDD_IO_33 AA8 A2 LVDS_BIT
100p/50V RN239 NC/0R 3.3V_VCCIO-AA8 LVDS_BIT
STV_D_1D1G 2,4 VDD_DDR_33L V7 B3 CABC_EN
STV_D_TCON V1 3.3V_DDR-V7 CABC_EN A3 OD_EN
RN122 0R CPV_2 STV_D/VSYNC OD_EN
VDD_LVDS_33 7 CPV CPV_1 V2 A4 UD_SEL
OE1 W1 CPV UD_SEL U5 VDD_DDR_33R
CN103 CN104
RN40 NC/0R 1 W2 OE1 3.3V_DDR-U5 J6 VDD_12
7 Terminate STV_U OE2
100n/16V 1 STV_U W3 OE2 1.2V_VCC-J6 G6 VDD_12
100p/50V STV_U 1.2V_VCC-G6
VDD_DDR_33L V5 R7
K8 3.3V_DDR-V5 GND-R7 AA7 VDD_LVDS_33
RN38 0R GPO_4 GND-K8 3.3V_LVDS-RX-AA7
VDD_DDR_33L 8 POL GOA1 1 GOA1 W4 AC6 VDD_LVDS_33
1 CPV_2 Y2 GOA1_DE 3.3V_LVDS-RX-AC6 Y6 VDD_LVDS_33
CN105 CN108
GOA2_CLK 3.3V_LVDS-RX-Y6
100n/16V
100p/50V
VDD_DDR_33R
MAIN3V3
NN17
5
GPO3 1
1 GPO_3
GPO_4
GPO_5
VDD_DDR_33L
Y3
Y4
Y5
U6
L8
GOA3_GPO3
GOA4_GPO4
GOA5_HSYNC
3.3V_DDR-U6
NT71790-
GND-L8
CN109
CN117 1 CPV_1 VDD_12 H6
1.2V_VCC-H6
TCON
VCC
4 B TP_TCON AA1
TP
GND
100n/16V 7 CPV Y POL_TCON AA2

2 CPV_2 POL
C 100p/50V A PWMO AA3 C
3.3V 8 PWMO PWMO
VDD_IO_33 AB8 P7
NC/74LVC1G32 3.3V_VCCIO-ABB GND-P7
3
3.3V VDD_DDR_33L V6 J8 VDD_LVDS_12

PWMI AA4 3.3V_DDR-V6 1.2V_LVDS-RX-J8 J10 VDD_LVDS_12
CN119 CN121 8 PWMI
M8 PWMI 1.2V_LVDS-RX-J10 J9 VDD_LVDS_12
100n/16V EN_2TCON AB1 GND-M8 1.2V_LVDS-RX-J9 J4
100p/50V EN_2TCON GNDAM_MLVDS-J4
2D1G CPV Option SYNC1 1 1 TCON_SYNC1 AB2
TTCON_MST_SYNC1 GNDAM_MLVDS-H4
H4
SYNC2 1 1 TCON_SYNC2 AB3
TTCON_Mute_M2S_SYNC2 GNDAM_MLVDS-G4
G4
SYNC3 1 1 TCON_SYNC3 AC2
TTCON_Mute_M2S_SYNC3 GNDAM_MLVDS-V4
V4
SYNC4 1 1 TCON_SYNC4 AC3 V3
放在正面 Terminate 1 Te POL 1 POL TTCON_OSC_SYNC4 GNDAM_MLVDS-V3
3.3V_MLVDS_VCCAM-N6
3.3V_MLVDS_VCCAM-R5
3.3V_MLVDS_VCCAM-R6
3.3V_MLVDS_VCCAM-P5
3.3V_MLVDS_VCCAM-P6
3.3V_MLVDS_VCCAM-T5
3.3V_MLVDS_VCCAM-T6
1 1 VDD_IO_33 AC8 U4
VDD_DDR_33L U7 3.3V_VCCIO-AC8 GNDAM_MLVDS-U4 T4
CPV 1 CPV 3.3V_DDR-U7 GNDAM_MLVDS-T4
VDD_12 H7 R4
3.3V_LVDS-RX-AC7
3.3V_LVDS-RX-AB6
3.3V_LVDS-RX-AA6
3.3V_LVDS-RX-AB7
1.2V_LVDS-RX-H10
1
3.3V_LVDS-RX-W6
3.3V_LVDS-RX-W7
1.2V_VCC-H7 GNDAM_MLVDS-R4
1.2V_LVDS-RX-H8
1.2V_LVDS-RX-H9
3.3V_LVDS-RX-Y7
N8 P4
3.3V_VCCIO-W8
GSEL 1 GSEL OE1 1 OE P8 GND-N8 GNDAM_MLVDS-P4 N4
1 1 GND-P8 GNDAM_MLVDS-N4
3.3V_DDR-U8
1.2V_VCC-G5
3.3V_DDR-V8
1.2V_VCC-J7
1.2V_VCC-J5
M4
STV 1 STV TP 1 TP GNDAM_MLVDS-M4 L4
1 1
750TEST
GNDAM_MLVDS-L4
EE_SDA
GND-N7
EE_SCL
GND-K7
GND-K6
M3
GNDAM_MLVDS-M3
RSTN
L3
3.3V 3.3V GNDAM_MLVDS-L3
NT71322_AAC-Final_22
AC5
AB5
AA5
AB4
W8
J7
G5
J5
K7
W6
Y7
AB6
AC7
N6
P5
P6
R5
R6
T5
T6
K6
H8
H9
H10
U8
V8
N7
W7
AA6
AB7
EEPROM RN33RN31
NN6
VDD_MLVDS_33
VDD_MLVDS_33
VDD_MLVDS_33
VDD_MLVDS_33
VDD_MLVDS_33
VDD_MLVDS_33
VDD_MLVDS_33
4.7k 4.7k
VDD_LVDS_12
VDD_LVDS_12
VDD_LVDS_12
TEST
1 8
RSTN
EE_SCL
EE_SDA
VDD_IO_33
VDD_LVDS_33
VDD_LVDS_33
VDD_LVDS_33
VDD_LVDS_33
VDD_LVDS_33
VDD_LVDS_33
VDD_LVDS_33
VDD_DDR_33L
VDD_DDR_33L
3.3V 2 A0 VCC 7
VDD_12
VDD_12
VDD_12
3 A1 WP 6
A2 SCL EE_SCL 2
TEST RN36 1k/NC 4 5
Vss SDA EE_SDA 2
BIST RN37 1k/NC
LVDS_TYP_TCON RN39 1k/NC NC/24LC64I/SN
LVDS_BIT RN43 1k/NC CN29 2,4 GPIO_10 GPIO_10 RN113 1k
CABC_EN RN44 1k/NC 100n/16V
OD_EN RN45 1k/NC
UD_SEL RN47 1k
EN_2TCON RN49 1k/NC
RN50
RN52
RN105
RN53
RN103
RN91
RN90
RN83
B B
By pass capacitor
VDD_IO_33 VDD_LVDS_33 VDD_LVDS_12
10k10k10k10k10k10k10k 10k CN113 CN110 CN106 CN101 CN87
CN120
100n/25V 100n/25V 100n/25V 100n/25V 100n/25V

100n/25V
VDD_DDR_33L VDD_MLVDS_33 VDD_12

CN112 CN111 CN115 CN99 CN98
CN116
100n/25V 100n/25V 100n/25V 100n/25V 100n/25V

100n/25V
A A
<OrgName>
Title
<Title>
Size Document Number Rev

C <Doc> ?
Date: Wednesday, February 06, 2013 Sheet 1 of 9

5 4 3 2 1
5 4 3 2 1
RN164 0R
5,8 GA_SCL GA_SCL SCK_Master GPIO14
GPIO15
RN165 0R VDD_OSC_2.5V VDD_MMU_1.8V
1
1
5,8 GA_SDA GA_SDA SDA_Master
MDQS1N
MDQS0N
MDQS1
MDQS0
GPIO_15 1
GPIO_14 1
SCK_Master
SDA_Master
VDD_3.3V
SCK_Slaver
SDA_Slaver
MDM1
MDM0
OSCO
MD05
MD02
MD00
MD07
MD13
MD10
MD08
MD15
MD11
MD09
MD14
MD12
MD06
MD01
MD03
MD04
OSCI
GPIO_13
GPIO_12
GPIO_11
GPIO_10
RN147 0R
GPIO_9
GPIO_8
GPIO_7
1 EE_SCL EE_SCL SCK_Master VDD_MMU_1.8V
MWEN RN126 22R DDR2_WEN DDR2_WEN 4
RN157 0R MBA1 RN129 22R DDR2_BA1
1 EE_SDA EE_SDA SDA_Master VCC_CORE_1.0V DDR2_BA1 4
1,4 GPIO_10 GPIO_10 VCCA_DDR_1.0V MBA0 RPN9
1 822R DDR2_BA0 DDR2_BA0 4
GPIO_12 1 MA10 2 7 DDR2_A10
7 LC 1 LC
MA1 3 6 DDR2_A1
G15
G19
G21
G12
G13
H17
D12
D11
D10
H18
C10
C11
D17
C12
C13
C14
C15
C16
B14
A15
B16
E12
E11
E10
B10
B12
B13
B15
A16
B17
B18
A18
A19
B19
B20
B21
A21
A22
B22
F15
F19
F20
F12
F13
W9
GPIO_15 4 5
C7
D9
C8
D8
D7
MA3 DDR2_A3
B8
A7
B7
E9
E8
E7
B9
A9
5 GPIO_15
MFIO_0 NN1A RN128
D 8 MFIO_0 R13 H12 MA7 RPN8
1 822R DDR2_A7
D
0R/NC
VCC_1.0V_CORE-H17
SCK_MASTER-C7
VCC_1.0V_CORE-H18
VDD_OSC_2.5V-E8
VDD_OSC_2.5V-E7
VDD_OSC_2.5V-D8
VDD_OSC_2.5V-D7
OSCO
GND_OSC-G15
GND_CLK-F20
VDD_MMU_1.8V-G19
GND-B14
GND-A15
GND-B16
GPIO_15
GPIO_14
GPIO_13
GPIO_12
GPIO_11
GPIO_10
GPIO_09
GPIO_08
GPIO_07
GND_OSC-F15
MDQ5
MDQ2
MDQ0
VDD_MMU_1.8V-D17
MDQ7
MDM1
MDQ13
MDQ10
MDQ8
MDQ15
VDD_MMU_1.8V-F19
MDQS1#
MDQS1
MDQS0#
MDQS0
MDQ11
MDQ9
MDQ14
MDQ12
MDM0
MDQ6
MDQ1
MDQ3
MDQ4
GND-F12
GND-F13
GND_APLL
GND-G12
GND-G13
SDA_MASTER-B8
SCK_SLAVE-A7
SDA_SLAVE-B7
VDD_IO_3.3V-W9
OSCI
T12 GND-R13 GND-H12 H13 MA12 2 7 DDR2_A12
8 MFIO_1 MFIO_1 GND-T12 GND-H13
T13 C23 MCKE 4 MA5 3 6 DDR2_A5
U12 GND-T13 DDR_CKE-C23 F17 MA9 4 5 DDR2_A9
8 MFIO_2 MFIO_2 GND-U12 VCCA_1.0V-F17 VCCA_DDR_1.0V
U13 G20
GND-U13 GND_CLK-G20 B23 MWEN MRASN RPN7
1 822R DDR2_RASN
8 MFIO_3 MFIO_3 MWE# DDR2_RASN 4
D22 MBA1 MA2 2 7 DDR2_A2
MBA1 D21 MBA0 MA11 3 6 DDR2_A11
8 MFIO_4 MFIO_4 VDDD MBA0 E22 MA10 MA8 4 5 DDR2_A8
MA10 F18
8 MFIO_5 MFIO_5 VCCA_1.0V-F18 VCCA_DDR_1.0V
H19 MA6 RPN6
1 822R DDR2_A6
RN268 VDD_MMU_1.8V-H19 E21 MA1 MA4 2 7 DDR2_A4
MFIO_6 MFIO_6 MA1 DDR2_A[0..12] 4
3.3k F23 MA3 MA0 3 6 DDR2_A0
MA3 F21 MA7 MCASN 4 5 DDR2_CASN DDR2_CASN
8 MEMC ON/OFF MFIO_7 MA7 4
G22 MA12
MA12 H22 MA5 MCLK0N RN145 22R DDR2_CLK0N
8 MFIO_8 MFIO_8 MA5 DDR2_CLK0N 4
H23 MA9 MCLK0 RN155 22R DDR2_CLK0 DDR2_CLK0 4
MFIO_9 MA9 F7
7,8 3D_EN VDD_DLL_2.5V-F7 VDD_DLL_2.5V
LVDSTX_2.5V F9 E17 VDD_MMU_1.8V
LVDSTX_2.5V-F9 VDD_MMU_1.8V-E17 P21
8 MFIO_10 MFIO_10 DDR_ODT MODT 4 MDM0 RN93 22R DDR2_DM0 DDR2_DM0 4
J23 MCLK0N MDM1 RN114 22R DDR2_DM1
8 MFIO_11 MFIO_11 MCLK# J22 MCLK0 VDD_MMU_1.8V DDR2_DM1 4
MCLK H20
MFIO_12 VDD_MMU_1.8V-H20 RN19 MDQS1N RPN3
1 822R DDR2_DQS1N
8 MFIO_12 F14 H21 MVREF DDR2_DQS1N 4
GND-F14 DDR_VREF-H21 MDQS1 2 7 DDR2_DQS1 DDR2_DQS1 4
K22 MRASN MDQS0N 3 6 DDR2_DQS0N
MRAS# CN128 1k CN122 DDR2_DQS0N 4
1 MFIO_13
1,4 STV_D_1D1G
1 MFIO_15
MFIO_13
GPIO_9
MFIO_15
VDDD NT71790-MEMC MA2
MA11
MA8
MA6
L22
L23
M23
M22
N22
MA2
MA11
MA8
MA6
MA4
100n/10V
RN35
1k 1u/10V
MDQS0
MD05
MD02
MD00
RPN2
1
4
2
3
5
822R
7
6
DDR2_DQS0
DDR2_DQ5
DDR2_DQ2
DDR2_DQ0
DDR2_DQS0
DDR2_DQ[0..15]
4
4
MA4
3.3k RN272
N21 MA0 MD07 4 5 DDR2_DQ7

MA0 J19
8 LVDS_TYP GPIO_14 VDD_MMU_1.8V-J19 P23 MCASN MD13 RPN1
1 822R DDR2_DQ13
MCAS# J20
8 GPIO_13 GPIO_13 VDD_MMU_1.8V-J20 MD10 2 7 DDR2_DQ10
K19 MD08 3 6 DDR2_DQ8
L18 VDD_MMU_1.8V-K19 K20
VCC_1.0V_CORE-L18 VDD_MMU_1.8V-K20 MD15 4 5 DDR2_DQ15
G14 D18
C
GND-G14 VDD_MMU_1.8V-D18 J21 MVREF C
DDR_VREF-J21 MD11 RPN5
1 822R DDR2_DQ11
F8 MD09 2 7 DDR2_DQ9
VDD_DLL_2.5V-F8 G7
VDD_DLL_2.5V-G7 VDD_DLL_2.5V MD14 3 6 DDR2_DQ14
G8 MD12 4 5 DDR2_DQ12
MAIN1V VDD_DLL_2.5V-G8 J17
VCC_1.0V_CORE-J17 V20 TEST_EN
312TEST MD06 RPN4
1 822R DDR2_DQ6
RX_VMM_1.0V Y23 RESETN MD01 2 7 DDR2_DQ1
RESET# V23 SPI_DI
SPI_DI MD03 3 6 DDR2_DQ3
VCC_CORE_1.0V V22 SPI_DO MD04 4 5 DDR2_DQ4
G9 SPI_DO V21 SPI_CLK
LVDSTX_2.5V-G9 SPI_CK W21 SPI_CS
SPI_CS Y9
VCC_CORE_1.0V VDD_IO_3.3V-Y9 W22 GPIO_6
GPIO_06 Y22 GPIO_5
VCCA_DDR_1.0V GPIO_05 AB23 MFIO_15
MFIO_15 AA23 MFIO_14 1 CN145
MFIO_14 1 MFIO14 OSCI RN132 100R
AC22 MFIO_13 1
MFIO_13 1 MFIO13 OSCO
AB22 MFIO_12 1 MFIO12
2
MFIO_12 1
RN110
DDR_72310_1V8 AA22 MFIO_11 1 JAM12D 22p/50V
VCC_1.0V_CORE-K18
VCC_1.0V_CORE-K17
VCC_1.0V_CORE-L17
VCC_1.0V_CORE-J18
MFIO_11 1 MFIO11
LVDSRX_VMM_1.0V
Y21 MFIO_10 1
LVDSRX_2.5V-P11
MFIO_10 1
VDD_IO_3.3V-AC9
MFIO10 CN148
1M
VDD_IO_3.3V-AB9
VDD_IO_3.3V-AA9
Y20 MFIO_9 ZN1
GNDA_RX-AA17
MFIO_09
GNDA_RX-W10
H14 W20 MFIO_8 1
GNDA_RX-V10
1
GND-H14 MFIO_08 1 MFIO8 RN156 100R
ICE-DSU_RX
J14 T14
ICE-DSU_TX
VDD_MMU_1.8V GND-J14 GND-T14

UART_RX1
UART_TX1
K14 J12 22p/50V

GND-M12
GND-M13
GND-N12
GND-N13
GND-R12
GND-K13
GND-P12
GND-P13
GND-L12
GND-L13
GND-K14 GND-J12
MFIO_00
MFIO_01
MFIO_02
MFIO_03
MFIO_04
MFIO_05
MFIO_06
MFIO_07
GPIO_00
GPIO_01
GPIO_02
GPIO_03
GPIO_04
ROCLK+
RECLK+
ROCLK-
L14 R14
RECLK-
DDR_VDD_CLK_1.8V GND-L14 GND-R14
RO0+
RO1+
RO2+
RO3+
RO4+
M14 J13
RE0+
RE1+
RE2+
RE3+
RE4+
RO0-
RO1-
RO2-
RO3-
RO4-
RE0-
RE1-
RE2-
RE3-
RE4-
N14 GND-M14 GND-J13 K12
P14 GND-N14 GND-K12
GND-P14 VDD_3.3V_MIS
VDD_3.3V_MIS
K13
L12
L13
M12
M13
L17
AA12
Y14
Y12
W12
AB9
Y13
W13
W14
Y15
W15
K18
T15
AA17
AB12
AA13
AB13
AC13
AA14
AC14
AB14
AA15
AB15
AA16
AB16
AC16
P11
V10
AB17
AA18
AB18
AC18
AA19
AC19
AB19
AA20
AB20
AA21
AB21
AC21
W10
J18
W16
Y16
W17
Y17
W18
Y18
W19
Y19
AA9
K17
AC9
N12
N13
P12
P13
R12
LVDS_ROCLK+
4.7k
4.7k
4.7k
4.7k
4.7k
LVDS_ROCLK-
4.7k
4.7k
4.7k
LVDS_RECLK+
LVDS_RECLK-
LVDS_RE4+
ICE-DSU_RX
LVDS_RO3+
LVDS_RO4+
LVDS_RE3+
ICE-DSU_TX
LVDS_RE3-
LVDS_RE4-
LVDS_RO0+
LVDS_RO1+
LVDS_RO2+
LVDS_RO3-
LVDS_RO4-
LVDS_RE0+8 LVDS_RE0+
LVDS_RO0-
LVDS_RO1-
LVDS_RO2-
LVDS_RE0-8 LVDS_RE0-
XSN9
UART-RX1
RN124
UART-TX1
RN94
RN125
RN133
8 1MFIO_0
MFIO_1
MFIO_2
MFIO_3
8 1MFIO_4
MFIO_5
1MFIO_6
MFIO_7
GPIO_0
GPIO_1
GPIO_2
GPIO_3
GPIO_4
RN141
1
RN136
RN137
RN138
B 2 B
3 ICE-DSU_RX SCK_Master
4 ICE-DSU_TX SDA_Master
5 UART-RX1
LVDS_RO3+
LVDS_RO4+
LVDS_RO3-
LVDS_RO4-
8
8
8
8
8
8
8
LVDS_RE3-8
LVDS_RE3+8
LVDS_RE4-8
LVDS_RE4+8
8
LVDS_RO0+
LVDS_RO1+
LVDS_RO2+
LVDS_RO0-
LVDS_RO1-
LVDS_RO2-
18
8
8
8
LVDS_ROCLK+
LVDS_ROCLK-
LVDS_RECLK-
LVDS_RECLK+
VDD_3.3V_MIS
1
6 UART-TX1
MFIO0 MFIO4 MFIO6
1
8
7
RN143
1
10k 8 SCK_Slaver SCK_Slaver
1N4148W 8 SDA_Slaver SDA_Slaver
MFIO1 MFIO5MFIO7
RX:NEAR CHIP SIDE RN127
1
RESETN
0R/NC RX_VMM_1.0V LVDSRX_2.5V
LVDS_RO0+ RN134 100R LVDS_RO0-
CN161
LVDS_RO1+ RN108 100R LVDS_RO1-
LVDS_RO2+ RN117 100R LVDS_RO2- 10u/25V
VDD_3.3V_MIS
LVDS_ROCLK+ RN130 100R LVDS_ROCLK-
LVDS_RO3+ RN135 100R LVDS_RO3- NN5 CN152 1,4,8 GPIO_[0..11]
LVDS_RO4+ RN148 100R LVDS_RO4- RN106 GPIO_0
SPI_CS 1 8 SPI_VCC RN109 100n/10V LN3 NT72312_+2.5V GPIO_1
10k SPI_DI 2 CS#_0 VCC 7 SPI_HOLD
RN77 BLM18PG181SN1 GPIO_2
LVDS_RE0+ RN158 100R LVDS_RE0- MFIO_14 SPI_WP 3 DOHOLD#_6 6 SPI_CLK
LVDS_RE1+ RN107 100R LVDS_RE1- WP#_2 CLK 10k GPIO_3
0R 4 5 SPI_DO VDD_DLL_2.5V GPIO_4
LVDS_RE2+ RN151 100R LVDS_RE2- VSS DI
LVDS_RECLK+ RN116 100R LVDS_RECLK- GPIO_5
EN25B40EN25F40-100GCP VDD_OSC_2.5V
LVDS_RE3+ RN131 100R LVDS_RE3-
LVDS_RE4+ RN142 100R LVDS_RE4- LVDSTX_2.5V
CO-LAYOUT DIP 8PIN GPIO_6
LN2
BLM18PG181SN1 GPIO_7
GPIO_8
LVDSRX_2.5V GPIO_9
GPIO_10
GPIO_11
VCCA_DDR_1.0V RX_VMM_1.0V VDD_DLL_2.5V VDD_OSC_2.5V LVDSTX_2.5V

TEST_EN VDD_MMU_1.8V DDR_VDD_CLK_1.8V VCC_CORE_1.0V VCC_CORE_1.0V LVDSTX_2.5V LVDSRX_2.5V VDD_3.3V CN127
100n/10V CN154
10u/10V CN177
100n/10V CN178
10u/10V CN191
100n/10V CN192
A 10u/10V A
10u/10V CN124
4.7k
10u/10V CN123
10u/10V CN142
10u/10V CN151
10u/10V CN156
10u/10V CN159
10u/10V CN147
100n/10V CN157
100n/10V CN173
100n/10V CN184
100n/10V CN193
10u/10V CN174
100n/10V CN176
100n/10V CN153
100n/10V CN163
100n/10V CN179
100n/10V CN194
100n/10V CN125
100n/10V CN149
100n/10V CN160
10u/10V CN146
100n/10V CN162
100n/10V CN175
10u/10V CN230
100n/10V CN169
100n/10V CN166
100n/10V CN168
100n/10V CN171
100n/10V CN172
100n/10V CN164
100n/10V CN165
100n/10V CN167
CN126 CN141 CN150 CN155 CN158 CN170

RN149
100n/10V 100n/10V 100n/10V 100n/10V 100n/10V

100n/10V
<OrgName>
Title
<Title>

C <Doc> ?
5 4 3 2 1
5 4 3 2 1
VCC_CORE_1.0V LVDSTX_2.5V
D RX_VMM_1.0V D
LVDSRX_2.5V
M11
G10
G11
R18
U16
U17
U18
U19
U20
U21
U22
U23
H11
N11
U15
R11
K11
T16
T17
T18
T19
T20
T21
T22
T23
F10
F11
L11
J11
NN1C
R17
VCC_1.0V_CORE-R18
VCC_1.0V_CORE-T16
VCC_1.0V_CORE-T17
VCC_1.0V_CORE-T18
VCC_1.0V_CORE-T19
VCC_1.0V_CORE-T20
VCC_1.0V_CORE-T21
VCC_1.0V_CORE-T22
VCC_1.0V_CORE-T23
VCC_1.0V_CORE-U16
VCC_1.0V_CORE-U17
VCC_1.0V_CORE-U18
VCC_1.0V_CORE-U19
VCC_1.0V_CORE-U20
VCC_1.0V_CORE-U21
VCC_1.0V_CORE-U22
VCC_1.0V_CORE-U23
LVDSTX_2.5V-G10
LVDSTX_2.5V-G11
LVDSTX_2.5V-K11
LVDSTX_2.5V-F10
LVDSTX_2.5V-F11
LVDSTX_2.5V-H11
LVDSTX_2.5V-J11
LVDSTX_2.5V-L11
LVDSTX_2.5V-M11
LVDSTX_2.5V-N11
LVDSRX_VMM_1.0V-U15
LVDSRX_2.5V-R11
P18 VCC_1.0V_CORE-R17
P17 VCC_1.0V_CORE-P18 V11
N18 VCC_1.0V_CORE-P17 GNDA_RX-V11 V12
N17 VCC_1.0V_CORE-N18 GNDA_RX-V12 V13
M18 VCC_1.0V_CORE-N17 GNDA_RX-V13 V14
M17 VCC_1.0V_CORE-M18 GNDA_RX-V14 V15
VCC_1.0V_CORE-M17 GNDA_RX-V15 V16
GNDA_RX-V16 V17
GNDA_RX-V17 V18
GNDA_RX-V18 V19
D15 GNDA_RX-V19 W11
D16 VDD_MMU_1.8V-D15 GNDA_RX-W11 Y10
E19 VDD_MMU_1.8V-D16 GNDA_RX-Y10 Y11
VDD_MMU_1.8V-E19 GNDA_RX-Y11 AA10
E15 GNDA_RX-AA10 AA11
E16 VDD_MMU_1.8V-E15 GNDA_RX-AA11 AB10
VDD_MMU_1.8V VDD_MMU_1.8V-E16 GNDA_RX-AB10
L19 AB11
L20 VDD_MMU_1.8V-L19 GNDA_RX-AB11 AC10
VDD_MMU_1.8V-L20 GNDA_RX-AC10 AC11
GNDA_RX-AC11
D19
NT71790- GND-N15
GND-N16
N15
N16
P15
VDD_MMU_1.8V-D19 GND-P15
C
E18
VDD_MMU_1.8V-E18
Power GND-P16
GND-R15
GND-R16
GND-U14
P16
R15
R16
U14
K21
C
GND-K21 L21
G17 GND-L21 M21
VCCA_DDR_1.0V VCCA_1.0V-G17 GND-M21
G18 P22
VCCA_1.0V-G18 GND-P22 R21
GND-R21 R22
D20 GND-R22 R23
VDD_CLK_1.8V-D20 GND-R23
DDR_VDD_CLK_1.8V
R20
E20 GND-R20 R19
VDD_CLK_1.8V-E20 GND-R19 P20
GND-P20 P19
F16 GND-P19 N20
G16 GND_OSC-F16-F16 GND-N20 N19
GND-M10
GND-M15
GND-M16
GND-N10
GND-R10
GND-U10
GND-U11
GND-C17
GND-C18
GND-C19
GND-C20
GND-C21
GND-C22
GND-H15
GND-H16
GND-D13
GND-D14
GND-K10
GND-P10
GND-K15
GND-K16
GND-E13
GND-E14
GND-T10
GND-T11
GND-L10
GND-L15
GND-L16
GND_OSC-G16-G16 GND-N19
GND-J15
GND-J16
GND-M9
GND-N9
GND-R8
GND-R9
GND-U9
GND-K9
GND-P9
GND-V9
M20
GND-T8
GND-T9
GND-L9
GND-M20 M19
GND-M19
NT71322_AAC-Final_22
K9
K10
L9
L10
M9
M10
N9
N10
P9
P10
R8
R9
R10
T8
T9
T10
T11
U9
U10
U11
V9
C17
C18
C19
C20
C21
C22
H15
H16
J15
J16
K15
K16
L15
L16
M15
M16
D13
D14
E13
E14
B B
A A
<OrgName>
Title
<Title>

C <Doc> ?

5 4 3 2 1
5 4 3 2 1
DDRII 512Mb/1Gb layout compatible VCC3.3V MAIN3V3

VDDD VCC3.3V
512Mb:BA2 NC, 1Gb:BA2 used RN48
MAIN3V3 VDD_3.3V
0R RN56
0R
NN2 3.3V
2 DDR2_A[0..12] DDR2_DQ[0..15] 2 CN26 LN1 NC/10.0 uH
DDR2_A0 M8 B9 DDR2_DQ15 VCC-Panel 1
A0 DQ15 10u/10V 1
DDR2_A1 M3 B1 DDR2_DQ14 RN55 NC/0R RN235 100k
DDR2_A2 M7 A1 DQ14 D9 DDR2_DQ13
D
A2 DQ13 VDD_3.3V_MIS NN12 D
DDR2_A3 N2 D1 DDR2_DQ12 1 8 CN7 RN1
A3 DQ12 BS SS
CN12
22u/6.3VCN9
CN6
DDR2_A4 N8 D3 DDR2_DQ11 CN27 26.1k
DDR2_A5 N3 A4 DQ11 D7 DDR2_DQ10 100n/16V
100n/16V
22u/6.3V
A5 DQ10 10u/10V RN96 NC/100K
NC/10u/16VCN8
CN13
CN3
DDR2_A6 N7 C2 DDR2_DQ9 2 7
DDR2_A7 P2 A6 DQ9 C8 DDR2_DQ8 IN EN
CN10
100n/16V
10u/16V
DDR2_A8 P8 A7 DQ8 DDR_72310_1V8 CN102 100n/16V
A8 10n/50V
DDR2_A9 P3 A8 DDR2_DQS1N DDR2_DQS1N +V_SW4 3 6 CN2 RN2 RN3
A9 UDQS#_47 2
DDR2_A10 M2 B7 DDR2_DQS1 SW COMP 10k
A10/AP_10 UDQS DDR2_DQS1 2 CN28 GND
DDR2_A11 P7 B3 DDR2_DM1
TGND
A11 UDM DDR2_DM1 2 3.3n/50V 6.8k
DDR2_A12 R2 10u/10V 4 5
DDR2_CLK0 RN13 100R DDR2_CLK0N R8 A12 GND FB
R3 NC
NC_14 DQ7
F9 DDR2_DQ7
DDR2_DQ[0..15] 2
VDD_DDR2_1V8 NC/MP1484
3.3=0.923(1+R4/R6)
9
R7 F1 DDR2_DQ6
NC_15 DQ6 H9 DDR2_DQ5
VDD_DM1 RN7 0R DDR2_BA2 L1 DQ5 H1 DDR2_DQ4 CN138
DDR2_BA1 L3 BA2 DQ4 H3 DDR2_DQ3 10u/10V
2 DDR2_BA1 BA1 DQ3
2 DDR2_BA0 DDR2_BA0 L2 H7 DDR2_DQ2
BA0 DQ2 G2 DDR2_DQ1 MAIN1V
DQ1 +V_SW6
RN10 2 DDR2_RASN DDR2_RASN K7 G8 DDR2_DQ0
0R/NC DDR2_CASN L7 RAS#_44 DQ0
2 DDR2_CASN CAS#_38 CN25
2 DDR2_WEN DDR2_WEN K3 E8 DDR2_DQS0N DDR2_DQS0N 2
L8 WE#_76 LDQS#_33 F7 DDR2_DQS0 10u/10V
CS#_42 LDQS DDR2_DQS0 2
2 MODT K9 F3 DDR2_DM0 DDR2_DM0 2
J2 ODT LDM
VRef_57 MAIN1V2
RN11 1k/NC RN8 K2
VDD_DM1 CKE
1k 2 MCKE
RN76 2 DDR2_CLK0 DDR2_CLK0 J8 A2
1k DDR2_CLK0N K8 CK NC_82 E2 RN51
2 DDR2_CLK0N CK#_40 NC_83 VCC3.3V NN13 NC/0R
VDD_DM1
22u/6.3VCN231
100n/16VCN225
VDD_DM1 J7 J1 3 4 1 1.2V
VSSDL VDDL VIN VOUT 1
10u/16VCN232
100n/16VCN233
A7 A9 VDD_3.3V_MIS
B2 VSSQ_77 VDDQ_58 C1 2
GND
B8 VSSQ_74 VDDQ_59 C3 VOUT
D2 VSSQ_78 VDDQ_60 C7
D8 VSSQ_75 VDDQ_61 C9 1
1
E7 VSSQ_73 VDDQ_62 E9 BS_7 2
AP1122E
C F2 VSSQ_72 VDDQ_63 G1 VDD_DDR2_1V8 GPIO_0 3 C
F8 VSSQ_79 VDDQ G3 4
CN140 RN12 100n/10V H2 VSSQ VDDQ_54 G7
1u/10V 1k/1% H8 VSSQ_80 VDDQ_55 G9 XSN10
CN139 P9 VSSQ_81 VDDQ_56 R1
N1 VSS_69 VDD_52 M9 CN100
J3 VSS_68 VDD_51 J9 10u/10V +V_SW6
RN9
1k/1% E3 VSS_67 VDD_50 E1 For Debug Update Code 1V
A3 VSS_66 VDD_49 A1
VSS VDD
VDD_DM1 RN216
H5PS5162GFR-G7C
NC/0R
VCC-Panel LN6 10.0 uH
VDD_DM1 1 1V
1
RN234 100k
100n/10V 100n/10V 100n/10V 100n/10V 100n/10V 100n/10V 100n/10V NN14
CN18 CN22 CN37 CN31 CN131 CN133 CN135 1 8 CN42 RN4
BS SS
CN45
CN43
CN41
2k
100n/16V
100n/16V
22u/6.3V
22u/6.3V
RN111NC/100K
CN44
CN47
CN40
CN32 CN129 2 7
CN46 IN EN
100n/16V
100n/16V 100n/16V
10u/16V
10u/16V
10n/50V CN144 100n/16V
CN17 CN136 CN137 CN19 CN23 CN24 CN130 CN132 CN134 3 6 CN39 RN6 RN5
100n/10V 100n/10V 100n/10V 100n/10V 100n/10V 100n/10V 100n/10V 100n/10V 100n/10V SW COMP
GND 12k
TGND
3.3n/50V 6.8k
4 5
GND FB
VDD_3.3V_MIS MP1484
1=0.923(1+R10/R11)
9
GPIO_[0..11] 1,2,8
BS_0 RN14 1k GPIO_0
BS_1 RN15 1k GPIO_1
BS_2 RN16 1k GPIO_2
BS_3 GPIO_3
BS_4 GPIO_4
BS_5 GPIO_5
+V_SW4
NT72312_+2.5V
B B
BS_6 GPIO_6
RN18 BS_7 GPIO_7
3.3V NN15 选用小封装的
RN95
3.3V RN115
0R 选用小封装的 NC/0R
1k/NC BS_8 GPIO_8 MAIN3V3 AP1084DGAZ1084D-ADJ MAIN3V3
BS_9 GPIO_9 1.8V NN16 2.5V
BS_10 GPIO_10 2 3 1 1 5 1
BS_11 GPIO_11 Vin_2 VOUT 1 VIN VOUT 1
ADJ
CN227 CN38
CN228100n/16V
CN4 RN194 CN226 CN5 RN198
RN20
RN21
RN22
RN23
RN24
RN25
RN26
RN27
RN28
CN229 CN143
GND
RN34 10u/10V100n/16V 1.5k 10u/10V 100n/16V 3 4
10u/10V 10u/10V 100n/16V
1
0R/NC ShutD ADJ 2.55k
TO-252 RN118
NC RN119 681R
AP2127K-ADJ
10k
10k
10k
10k
10k
10k
10k
10k
10k
2
GND GND
Vout=1.25(1+R162/R236)+0.000055*R162 GND GND
1.2k
GND GND
GND
VOUT=0.8*(1+R237/R163) V
A A
<OrgName>
Title
<Title>

C <Doc> ?
5 4 3 2 1
5 4 3 2 1
VDDA
VDD_GA POL_TCON 1 GSEL OP CIRCUIT
NN10
VDDA VDD_GA RN221
RN213 9
RN82 VDD_OP 15.2 NC/10k/1% 0R 1
NC1
EP
NC2
8
VDDA
0R 2 7
1 VDD_OP 3 IN- VDD 6 RN215 0R
1 IN+ OUT GSEL 1,8
D
4 5 D
RN84 RN85 CN74 GND NC3
NC/0R NC/10u/25V CN183CN187 CN188 CN189
10.2k RN197 MAX9650
NC/9.31k CN185 NC/10u/25V NC/10u/25V
1
100n/25V 100n/25V
2 VZN1
TL431BCDBZR
RN87
3
2k
NC/100n/25V
VCOMADJ
RN89 VDD_GA
VDD_GA RN185
0R
RN58 82k RN187
VCOM 82k RN59
CN85
CN51 CN56 100k GMA1 1 GMA1
CN52 100k 1u/25V 100n/25V 1 GMA1 8
RN256 1u/25V 100n/25V
VCOMB GMA2 1 GMA2
0R RN182 24.9k 1 GMA2 8
RN60 24.9k 1 RN180
1 GMA3 1 GMA3
RN61 10R CN82 10R 1 GMA3 8
RN54 CN238 CN58
100n/16V GMA4 1 GMA4
47k 1 GMA4 8
10u/16V 100n/16V
GMA5 1 GMA5
1 GMA5 8
33
32
31
30
29
28
27
26
25
33
32
31
30
29
28
27
26
25 NN8
GMA6
1
1 GMA6
GMA6 8
AVDD_24
AVDD_25
AGND_27
VCOM_FB
AGND_31
EPAD
VCOM_OUT
VCOM_ADJ
SET
NN7 IML7991ID
AVDD_24
AVDD_25
AGND_27
VCOM_FB
AGND_31
EPAD
VCOM_OUT
VCOM_ADJ
SET
GMA7 1 GMA7
IML7991ID 24 RN178 10R GMB14 CN55 100n/16V 1 GMA7 8
24 GMA14 GMB1 RN191 1 OUT14 23 GMB13
RN62 10R CN53 100n/16V CN84 100n/25V 10R RN192 10R CN92 100n/16V GMA8 1 GMA8
GMA1 RN63 1 OUT14 23 GMA13 GMB2 RN184 2 OUT1 OUT13 22 GMB12
CN57 100n/25V 10R RN64 10R CN54 100n/16V CN83 100n/25V 10R RN193 10R CN81 100n/16V 1 GMA8 8
GMA2 RN66 2 OUT1 OUT13 22 GMA12 GMB3 RN92 3 OUT2 OUT12 21 GMB11
CN59 100n/25V 10R RN65 10R CN60 100n/16V CN89 100n/25V 10R RN181 10R CN76 100n/16V GMA9 1 GMA9
CN64 100n/25V 10R RN69 10R CN63 100n/16V CN95 100n/16V 10R RN186 10R CN90 100n/16V GMA10 1GMA10
GMA6 RN73 6 OUT5 OUT9 18 GMA8 GMB7 RN86 7 OUT6 OUT8 17
CN70 100n/16V 10R RN74 10R CN69 100n/16V CN93 100n/16V 10R VDDD GMA11 1GMA11
OUT6 OUT8 OUT7 DVDD
BANK_SEL
STATIC_HI
C CN71 100n/16V GMA7 RN75 10R 7 17 VDDD 8 1 GMA11 8 C
OUT7 DVDD VDD_GA AVDD
BANK_SEL
STATIC_HI
CN78
nWR_23
8 CN80
VDD_GA AVDD GMA12 1GMA12
DGND
AGND
CN68
nWR_23
CN67 1 GMA12 8
SDA
SCL
DGND
AGND
1u/25V 100n/16V
A0
GMA13 1GMA13
SDA
SCL
1u/25V 100n/16V CN237CN236 1 GMA13 8

A0
CN235CN239
GMA14 1GMA14
9
10
11
BANK_SEL 12
13
14
15
16
VDD_OP
100n/25V
100n/25V
XSN8 1 GMA14 8
9
10
11
12
13
14
15
16
VDD_OP
100n/25V
100n/25V
GMB1 1 GMB1
5
6
1 GMB1 8
4 GA_SDA
GMB2 1 GMB2
GA_SDA 3 GA_SCL 1 GMB2 8
GA_SCL 2 CN94 nWR
CN75 GMB3 1 GMB3
CN72 CN73 nWR 1 1 GMB3 8
1u/25V 100n/25V
1u/25V RN139 3.3k GMB4 1 GMB4
100n/25V 1 GMB4 8
RN189 3.3k
RN183 3.3k GMB5 1 GMB5
RN78 NC/3.3kBANK_SEL RN79 NC/3.3k VDDD VDDD 1 GMB5 8
RN80 3.3k RN188 3.3k
GMB6 1 GMB6
1 GMB6 8
GMB7 1 GMB7
1 GMB7 8
VCC3.3V GMB8 1 GMB8
1 GMB8 8
GMB9 1 GMB9
1 GMB9 8
RN218 GMB10 1GMB10
nWR 1 GMB10 8
2.2k nWR 8
RN46 100R/NC RN207 BANK_SEL GA_SDA GMB11 1GMB11
GA_SDA 2,8 1 GMB11 8
3
100R GA_SCL
GA_SCL 2,8 GMB12 1GMB12
2 GPIO_15 GPIO_15 RN17 47k 1 1 GMB12 8
MMBT3904LT1
GMB13 1GMB13
1 GMB13 8
2
GMB14 1GMB14
1 GMB14 8
VCOM 1VCOM
1
B B
A A
<OrgName>
Title
<Title>

C <Doc> ?
5 4 3 2 1
5 4 3 2 1
2
VDN2
NC/APD340VRTR-G1NC/APD340VRTR-G1
VDN3
1
D D
CN198
NC/470n/50V
2
CN199
APD340VRTR-G1\TP\JK
VDN4
RN238 NC/100n/50V
8
NN20
1 NC/0R layout 特别注意
1
7 D1 S1 2
6 D1_5 S2 3 LN5 10.0 uH RN206
D2 S3 CN200
5 4
D2_7 G 10u/25V NC/6.8k
AVDD1 NC/P2003EVG VGH VGH
16V VCC-Panel V1
VDN5 1
3
VDDA 1
1
AO3401L VS VS
RN199 1 1 RN219
3 2
1
CN254 CN2550R CN201

CN202 NC/0R
CN203 RN232 CN206 NC/MMBT2907ALT1 2SA2071
2
10u/25V 10u/25V 10u/25V
10u/25V CN204 CN205 VN2
100n/25V 1M
10u/25V 10u/25V NC/220n/50V RN233
1
RN222 CN207 CN208 CN209

51k
NC/80.6k
CN411 NC/0805/1u/50V
AVDD=1.25*(1+(RN189+RN193)/RN196)=15.728V NC/10u/50V NC/470n/50V
NC/220p/50V
29
28
27
26
25
24
23
22
RN209 10k RN220
RN400 RN204 NN3
GND1
GND1
ENA2
ENA1
DRP
NC/3.48k
EPAD
SW
SW
1M 6.8k VGH=1.25*(1+R298/R302)
1 21
OS FBP RN205 RN210
2 20
AGND FSW 3k 130k
RN225 RN236
3 19 CN210
FB DLY1 CN211 RN200
4.99k 0R 47n/16V RN223
4 18 10.2k
GD COMPB 2.2n/50V
C RN217 CN212 30k C
5 17
COMP FBB
30k 2.2n/50V
CN213
6
AAT1133 16 VCC-Panel
SS AVIN
CBOOT
33n/16V
SWB1
CN214 7 15
DLY2
SWB
DRN
VCC
FBN
VREF VINB RN202
100n/25V CN215 16.9k
100n/25V
10
11
12
13
14
LN7 10.0 uH
RN203
VDDD
RN230 CN216 0R
1
10k
100n/25V
1
layout 特别注意 RN227 VDDD1
2
CN217 CN218 CN220 CN221
VDN6 10u/10V 10u/10V 10u/10V
NC/10n/50V
59k CN219 RB160M-30TR
100n/25V
1
CN222
1u/10V VDDD=1.25*(1+RN201/R199)
VN6 2 VN7
2
1 1
RN224
VSS 0R
2DD1664R-13
3
2DD1664R-13
3
1
RN228 RN208
VSS
1
0R 6.8k
B CN223 B
RN237 CN224 470n/25V

1k 4.7u/10V
VGL
VN8 VDN7
1
RN229 2 MMBT2907ALT1
3 1 2
VGL
1
0R
RB160M-30TR
1
RN226
1.5k VDN8
CN241
CN240 2 1
2.2u/25V 100n/25V
CN234
RN214 100n/25V RB160M-30TR
120R
1
VDN9
BZT52C10
2
A A
<OrgName>
Title
<Title>

C <Doc> ?
5 4 3 2 1
5 4 3 2 1
VDDD
RN252 CN256
0R/0402 120p/50V
CN264
RN298
1u/10V
191k
1 1 CPV STV
VDN10
FBG
D LN8 10.0 uH RN246 D
VCC-Panel 1 2 VGH
3DEN
END
REF
0R
VT
RB160L-90 RN295 CN263 CN259
CN258
CN244 CN247
100k NC 1u/50V 1u/50V
CN257
1u/25V 1u/25V RN245 FBG
41
40
39
38
37
36
35
34
33
32
31
NN19
NC
NC
G1
VCE
COMPG
FBG
VST
VIN
3DEN
END
VT
REF
PGND
RN297
1 Terminate Terminate 1 30 3.48k
Teminate LXG
2 LC LC 2 29
LC PMS VCC-Panel REF
RN296 RN276 RN273
3 28 set3 CN246
RN287 0R/0402 Rotate SET1 VDDA
1u/25V
4 27 set2 4.32k
NC/16.2k Ratio SET2 51k
RN247 RN290
VCOMADJ RN293NC/0R/0402 5 26 set1 CN262
VcomADJ SET3 4.99k RN292
100n/50V 60.4k
CN260 RN248NC/0R/0402 6 25 120k
AGND SHD
1u/25V RN250 END
VSS VSS 7 24 VT
GOAL VGON VGH
RN249 0R/0402
VSS_XON_L VSS_XON_L 8 23 CN265 CN267 CN242 CN243
XON NC3
0R/0402 100n/50V 1u/50V 1u/50V 1u/50V RN240 RN291
9 22 ST_L 8
VSS STH1 620k 100k
RN253 RN2890R/0402
VGL VGL 10 21 LC_L1 8
VGOFF LC1
CKH6
CKH5
CKH4
CKH3
CKH2
CKH1
STH2
0R/0402 RN2770R/0402
NC1
NC2
LC2
CN261 RN242
RN241
10u/25V 10K 130k
11
12
13
14
15
16
17
18
19
20
RT8922
VDDD
C C
set1 RN281 10k
0R/0402RN243
0R/0402RN255
0R/0402RN286
0R/0402RN294
0R/0402RN299
0R/0402RN274
RN280 NC/10k
0R/0402RN244
VGL
VDDD
1
set2 RN279 10k
RB160M-30TR RB160M-30TR
RN278 NC/10k
VDN11 VDN12
2
8
HC_L38
HC_L28
8
8
HC_L1
LC_L2
HC_L6
HC_L5
HC_L4
2
VDDD
VSS HC_R6 HC_L6
1 HC_R6 HC_L6 1
set3 RN285 NC/10k 1 1
RN315 NC/0R/0402
RN284 10k HC_R5 1 HC_R5 HC_L5 1 HC_L5
1 1
RN316NC/0R/0402
HC_R4 1 HC_R4 HC_L4 1 HC_L4
1 1
VDDD RN317NC/0R/0402
VDDD HC_R3 1 HC_R3 HC_L3 1 HC_L3
1 1
RN318 NC/0R/0402
3DEN RN283 NC/10k HC_R2 1 HC_R2 HC_L2 1 HC_L2
RN251 1 1
RN282 10k RN319NC/0R/0402
0R/0402 HC_R1 1 HC_R1 HC_L1 1 HC_L1
CN266 1 1
RN320NC/0R/0402
LC_R2 1 LC_R2 LC_L2 1 LC_L2
1 1
3D_EN RN275 NC/1k 3DEN RN321NC/0R/0402
2,8 3D_EN 1u/10V LC_R1 1 LC_R1 LC_L1 1 LC_L1
1 1
RN322NC/0R/0402
1 1 CPV STV VSS_XON_R VSS_XON_L
RN323NC/0R/0402
ST_R ST_L
3DEN
1ST_R ST_L 1
1 1
RN324NC/0R/0402
B B
41
40
39
38
37
36
35
34
33
32
31
NN21
G1
VCE
COMPG
FBG
VST
VIN
3DEN
END
VT
REF
PGND
1 Terminate Terminate 1 30
Teminate LXG
2 LC LC 2 29
LC PMS VCC-Panel
RN303 RN254 RN257
3 28 set3 CN245
RN288 0R/0402 Rotate SET1 VDDA
1u/25V
4 27 set2 4.32k
0R/0402 Ratio SET2 51k
RN258
VCOMADJ RN3010R/0402 5 26 set1 CN253
VcomADJ SET3 4.99k
100n/50V
CN248 RN259NC/0R/0402 6 25
AGND SHD
1u/25V RN262
VSS VSS 7 24
GOAL VGON VGH
RN261 0R/0402
VSS_XON_R VSS_XON_R 8 23 CN268 CN249 CN250 CN251
XON NC3
0R/0402 100n/50V 1u/50V 1u/50V 1u/50V
9 22 ST_R 8
VSS STH1
RN264 RN3000R/0402
VGL VGL 10 21 LC_R1 8
VGOFF LC1
CKH6
CKH5
CKH4
CKH3
CKH2
CKH1
STH2
0R/0402 RN2670R/0402
NC1
NC2
LC2
CN252
10u/25V
11
12
13
14
15
16
17
18
19
20
RT8922
0R/0402RN270
0R/0402RN266
0R/0402RN269
0R/0402RN302
0R/0402RN304
0R/0402RN271
0R/0402RN265
A A
<OrgName>
8
HC_R38
HC_R28
HC_R18
8
LC_R2
HC_R6
HC_R5
HC_R4
Title
<Title>

C <Doc> ?
5 4 3 2 1
5 4 3 2 1
XSN1
55
54
56 53
XSN3 XSNN4 Layout place Right
57
58
52
51
CN269 10u/16V Layout place Left
59 50 FN1 MFIO_0 100R LED_PWM1
2 MFIO_0 RN313
60 49 VCC-Panel 1 AMLV_5PO 1 HC_L6 HC_L6 7
61 48 MFIO_1 100R LED_PWM2
2 MFIO_1 RN312
47 F1206FA3000V032TM 2 AMLV_5NO 2 HC_L5 HC_L5 7
46 MFIO_3 100R LED_PWM3
2 MFIO_3 RN310
45 3 AMLV_4PO 3 HC_L4 HC_L4 7
44 MFIO_2 100R LED_PWM4
FN2 2 MFIO_2 RN311
43 RN347 0R BITSEL 4 AMLV_4NO 4 HC_L3 HC_L3 7 LVDS_RE3+ LVDS_RE4+
42 RN345 0R TEST_EN 1 6
GPIO_13 2 I/O1_3 IC2 2 MFIO_4 MFIO_4 RN305 100R LED_PWM5
41 LVDS_RE4+ LVDS_RE4+ 2 5 AMLV_3PO 5 HC_L2 HC_L2 7
40 LVDS_RE4- 2 5
LVDS_RE4- 2 GND VCC 2 MFIO_5 MFIO_5 RN314 100R LED_PWM6
D
39 LVDS_RE3+ LVDS_RE3+ 2 6 AMLV_3NO 6 HC_L1 HC_L1 7 LVDS_RE3- LVDS_RE4- D
38 LVDS_RE3- 3 4
LVDS_RE3- 2 I/O3_2 IC1
37 7 7 LC_L2 LC_L2 7 MFIO_10 RN326 100R 3D_Enable_High
ESDA6V8UF 2 MFIO_10
36 LVDS_RECLK+ LVDS_RECLK+ 2
35 LVDS_RECLK- LC_L1 7 FN3
LVDS_RECLK- 2 8 AMLV_CKPO 8 LC_L1 LVDS_RE2+ LVDS_RECLK+
34 1 6 MFIO_11 100R LED_PWM7
I/O1_3 IC2 2 MFIO_11 RN364
33 LVDS_RE2+ LVDS_RE2+ 2 9 AMLV_CKNO 9
32 LVDS_RE2- LVDS_RE2- 2 2 5 MFIO_12 LED_PWM8
GND VCC 2 MFIO_12 RN309 100R
31 LVDS_RE1+ LVDS_RE1+ 2 10 10 VSS_XON_LVSS_XON_L LVDS_RE2- LVDS_RECLK-
30 LVDS_RE1- LVDS_RE1- 2 3 4
I/O3_2 IC1
29 LVDS_RE0+ LVDS_RE0+ 2 82 GND 11 AMLV_2PO 82 GND 11
28 LVDS_RE0- LVDS_RE0- 2 ESDA6V8UF
11
27 RN344 0R 3D_LR_FLAG ST_L 7 FN4
GPIO_5 2,4 81 GND 12 AMLV_2NO 81 GND 12 LVDS_RE0+ 1 LVDS_RE1+
26 RN346 0R 3D_EN 6
3D_EN 2,7 I/O1_3 IC2 10 LED_PWM8 1 PWM8
25 LVDS_RO4+ LVDS_RO4+ 2 HC_R1 80 13 AMLV_1PO BMLV_0NO 80 13 9 LED_PWM7 1 1
7 HC_R1 2 5 1 PWM7
24 LVDS_RO4- LVDS_RO4- 2 GND VCC 8 LED_PWM6
23 LVDS_RO3+ LVDS_RO3+ 2 HC_R2 79 14 AMLV_1NO BMLV_0PO 79 14 LVDS_RE0- LVDS_RE1- 7 LED_PWM5 1
7 HC_R2 3 4 1 PWM5
22 LVDS_RO3- VDDD I/O3_2 IC1 6 LED_PWM4
21 LVDS_RO3- 2
HC_R3 78 15 AMLV_0PO BMLV_1NO 78 15 5 LED_PWM3 1 PWM3
20 LVDS_ROCLK+ 7 HC_R3 ESDA6V8UF 1
LVDS_ROCLK+ 2 FN5 4 LED_PWM2
19 LVDS_ROCLK- HC_R4 77 16 AMLV_0NO BMLV_1PO 77 16 LVDS_RO3+ LVDS_RO4+ 3 LED_PWM1 1
LVDS_ROCLK- 2 7 HC_R4 1 6 PWM1
18 I/O1_3 IC2 2 3D_Enable_High 1 1
17 LVDS_RO2+ LVDS_RO2+ 2 HC_R5 76 17 BMLV_2NO 76 17 1 1
7 HC_R5 VCOM 2 5 3D_En_H
16 LVDS_RO2- LVDS_RO2- 2 GND VCC
15 LVDS_RO1+ LVDS_RO1+ 2 HC_R6 75 18 GMA1 BMLV_2PO 75 18 LVDS_RO3- LVDS_RO4- XSN6
7 HC_R6 GMA1 5 3 4
12
14 LVDS_RO1- LVDS_RO1- 2 I/O3_2 IC1
13 LVDS_RO0+ LVDS_RO0+ 2 LC_R1 74 19 GMA2 74 19
12 LVDS_RO0- LVDS_RO0- 2 7 LC_R1 GMA2 5 ESDA6V8UF
11 FN6
LC_R2 73 20 GMA3 BMLV_CKNO 73 20 VDDA LVDS_RO2+ LVDS_ROCLK+
10 RN354 0R LD_EN 7 LC_R2 GMA3 5 1 6
I/O1_3 IC2
9 I2C-SCL-MMS RN342 NC/0R PWM_OUT PWMO 72 21 GMA4 BMLV_CKPO 72 21
PWMO 1 GMA4 5 2 5
8 I2C-SDA-MMS RN343 NC/0R PWM_IN PWMI
5
4
PWMI 1 GND VCC
7 RN341 0R LVDS_SEL VSS_XON_R 71 22 71 22 LVDS_RO2- LVDS_ROCLK-
VSS_XON_R 3 4 3 3D_Enable_High
6 nWR 5 I/O3_2 IC1
RN358 RN353 0R 2 LED_PWM1
5 100R L/R_OUT 70 23 GMA5 BMLV_3NO 70 23
GMA5 5 ESDA6V8UF 1
4 RN340 0R MEMC ON/OFF MEMC ON/OFF 2
3 RN349 0R I2C-SDA-MS FN7
7 ST_R ST_R 69 24 GMA6 BMLV_3PO 69 24 TP LVDS_RO0+ LVDS_RO1+ XSN11
2 RN348 0R I2C-SCL-MS GMA6 5 1 6
I/O1_3 IC2
1 68 25 GMA7 BMLV_4NO 68 25 POL
GMA7 5 2 5
GND VCC
67 26 GMB1 BMLV_4PO 67 26 POLS LVDS_RO0- LVDS_RO1-
GMB1 5 3 4
C I/O3_2 IC1 C
VDDD 66 27 GMB2 BMLV_5NO 66 27 GSEL

GMB2 5 ESDA6V8UF
65 28 GMB3 BMLV_5PO 65 28
POLS RN327 10k GMB3 5
64 29 64 29 GMA1
PWM_IN RN331 NC/100R PWM_OUT 63 30 GMB4 GMB14 63 30 GMA2 VCC3.3V VCC3.3V

VCOM GMB4 5
62 31 GMB5 GMB13 62 31 GMA3
VDDD GMB5 5
61 32 GMB12 61 32 GMA4 RN334 RN351
DP_SEL2 RN307 10k 1k 1k
RN306 NC/10k VDDA 60 33 GMB6 60 33 VN9 RN333 LVDS_TYP 2 VN12 RN350 GPIO_0 2,4
3
GMB6 5 100R 100R
H 120Hz L 60Hz 59 34 GMB7 GMB11 59 34 GMA5 LVDS_SEL RN335 1k 1 LD_EN RN352 1k 1
GMB7 5 MMBT3904LT1 MMBT3904LT1
I2C-SDA-MMS RN328 0R 58 35 GMA8 GMB10 58 35 GMA6
2
GA_SDA 2,5 GMA8 5
I2C-SCL-MMS RN332 0R
GA_SCL 2,5 TP 57 36 GMA9 57 36 GMA7
1 TP GMA9 5
GSEL1 POL 56 37 GMA10 GMB9 56 37 GMB1 VCC3.3V

1 POL GMA10 5
1 POLS 55 38 GMB8 55 38 GMB2
1
54 39 GMA11 GMA14 54 39 GMB3 RN356
1,5 GSEL GMA11 5 1k
53 40 GMA12 GMA13 53 40 VN13 RN355 MFIO_8 2
GMA12 5
3
100R
52 41 52 41 GMB4 BITSEL RN357 1k 1
5 GMB14
MMBT3904LT1
42 GMA13 42 GMB5
2
GMA13 5
43 GMA14 43
VN10 RN338 GMA14 5
0R/NC
44 GMB8 44 GMB6
100R GMB8 5
I2C-SCL-MS 3 2 RN336
SCK_Slaver 2 45 GMB9 45 GMB7
GMB9 5
2N7002 46 46 GMA8
1
B 47 GMB10 47 GMA9 M1 M2 B
Add: GMB10 5
VCC3.3V From SOC to FRC(Function control option) 48 GMB11 48 GMA10 1 1
GMB11 5
VN11 RN339 0R/NC 49 49
M3 M4
RN337 100R VCC3.3V 50 GMB12 50 GMA11
I2C-SDA-MS 3 2 GMB12 5
SDA_Slaver 2 1 1
51 GMB13 51 GMA12
VCC3.3V GMB13 5
2N7002
M5 M6
1
4
5
XSN7 HX0.5x80A HX0.5x80A

RN329 3 1 1
VCC3.3V
NC/2.2k 2
2,4 GPIO_6 Glass_Vsync L/R_OUT 1
RN330
100R
Layout place L
Layout place Right
XSN33 COF XSN44
62 62
61 61
VSS_XON_L 60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
BMLV_3NO
5 AMLV_CKNO
BMLV_CKNO
AMLV_CKPO
BMLV_CKPO
BMLV_3PO
8 AMLV_0NO
6 AMLV_1NO
8 AMLV_2NO
80R AMLV_3NO
6 AMLV_4NO
8 AMLV_5NO
BMLV_0NO
BMLV_1NO
BMLV_2NO
BMLV_4NO
BMLV_5NO
7 AMLV_0PO
5 AMLV_1PO
7 AMLV_2PO
7 AMLV_3PO
5 AMLV_4PO
7 AMLV_5PO
BMLV_0PO
BMLV_1PO
BMLV_2PO
BMLV_4PO
BMLV_5PO
DP_SEL2
DP_SEL2
HC_L6
HC_L5
HC_L4
HC_L3
HC_L2
HC_L1
HC_L1
HC_L2
HC_L3
HC_L4
HC_L5
HC_L6
LC_L2
LC_L2
LC_L1
LC_L1
VSS_XON_L 7 VSS_XON_L
GMA10
GMA13
GMA12
GMA11
GMA10
GMA14
GMA13
GMA12
GMA11
GMA9
GMA1
GMA8
GMA7
GMA6
GMA5
GMA4
GMA3
GMA2
GMA1
GMA9
GMA8
GMA7
GMA6
GMA5
GMA4
GMA3
GMA2
POL
POL
GMA14
1
1
1
1
1
1
1
1
TP
TP
VDDA
VSS_XON_L
0R
RPN14 0R 1
81
71
61
71
61
51
1
6
6
5
8
7
6
5
0RRPN11
RPN15 0R
RPN16 0R
RPN13 0R
A A
VCOM
VCOM
ST_L
ST_L
VDDD
VDDD
7
7
VDDA
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
LC_L2
LC_L1
0N0P1N1P2N2P CKN
CKP
LC_L1
LC_L2
HC_L6
HC_L5
HC_L4
HC_L3
HC_L2
HC_L1
HC_L1
HC_L2
HC_L3
HC_L4
HC_L5
HC_L6
AMLV_3N RPN12
RPN10
AMLV_0N 1
AMLV_0P 2
AMLV_1N 3
AMLV_1P 4
AMLV_2N 1
AMLV_2P 2
AMLV_CKN3
AMLV_CKP4
1
AMLV_3P 2
AMLV_4N 3
AMLV_4P 4
AMLV_5N 1
AMLV_5P 2
BMLV_0N 3
BMLV_0P 4
BMLV_1N 1
BMLV_1P 2
BMLV_2N 3
BMLV_2P 4
BMLV_CKN1
BMLV_CKP2
BMLV_3N 3
BMLV_3P 4
1
2
3
4
BMLV_4N
BMLV_5N
BMLV_4P
BMLV_5P
AMLV_1P
AMLV_2P
AMLV_3P
AMLV_4P
AMLV_5P
BMLV_1P
BMLV_2P
BMLV_3P
BMLV_4P
BMLV_5P
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AMLV_1N
AMLV_2N
AMLV_3N
AMLV_4N
AMLV_5N
BMLV_1N
BMLV_2N
BMLV_3N
BMLV_4N
BMLV_5N
AMLV_CKP
BMLV_CKP
AMLV_CKN
BMLV_CKN
AMLV_0P
BMLV_0P
1
1
1
1
AMLV_0N
BMLV_0N
<OrgName>
Title
<Title>

A2 <Doc> ?

5 4 3 2 1
10 9 8 7 6 5 4 3 2 1
Himax Solution
D D
Panel Type: VA_IPS-alpha 315

Resolution: 1366*768
Scan direction:
Dummy Channel:
Tcon: HX6710 _Single in/Dual out_ SD1 SD3 SD4 SD6

C C
SD: COF_HX8031-N42_684CH*6_
GD: COF_HX8651-FCU29 _256CH*3_
GD1
PWM: TPS65161
P-OP: HX5200
VIN: 12V
VDDD: 3.3V
B B
VDDA: 12.5V
GD3
VDDD_TCON: 3.3V
VDDA_TCON: 3.3V
VDDP_TCON: 3.3V
VDDM_TCON: 3.3V
VGH: 23V
VGL: -8V
A VCOM: 6V A
Vref: 12.4V
Τ
　春　筿　　　そ　
Title
Hisense IPS-alpha T-con board_V1.0_100428
DWG NO <OrgName> DATE
Size Checked Designer Drawer Rev SHEET

1
A1 <OrgAddr1> <OrgAddr2> <OrgAddr3> <RevCode>
6
"Himax" COPYRIGHT 2001 , ALL RIGHTS RESEREVD, COPYING FORBIDDEN
5 4 3 2 1
D Distance of the both test pad center is 2.00mm D

GND
XP1
Screw holes
31
1 XP4 VCCI
2 1 VCCI 5 XAO XAO 1 XP3
3 2 3 CPV CPV 2
PP2
4 3 3 STV STV 3 5 GM1 GM1 1
5 4 R5 VDDD 4 5 GM2 GM2 2
VDDD
6 5 GND 1 GND VGH VGH 5 5 GM3 GM3 3
1 VGL 5 GM4 GM4
7 6 VGL 6 4
8 7 0603/0R/5% VCOM VCOM 7 5 GM5 GM5 5
9 8 5 GM1 GM1 8 5 GM6 GM6 6
R24 0402/0R/5% S_SCL Screw Hole 5 GM2 GM2 5 GM7 GM7
10 9 9 7
S_SCL
11
12
10
11 GND
R23 0402/0R/5% S_SDA
S_SDA
3
3 Ellipse 5
5
GM3
GM4
GM3
GM4
10
11
3
3
POL_OUT
TP1
POL_OUT
TP1
8
9
13 12 RX0N 5 GM5 GM5 12 3 STV STV 10
RX0N 3 PP3
14 13 RX0P 5 GM6 GM6 13 11
GND RX0P 3 R4 5 GM7 GM7 3 BLV0P BLV0P
15 14 14 12
16 15 RX1N 1 GND 3 POL_OUT POL_OUT 15 3 BLV0N BLV0N 13
RX1P RX1N 3 1 3 TP1 TP1
17 16 RX1P 3 16 14
18 17 GND 0603/0R/5% 17 3 BLV1P BLV1P 15
RX2N PWMI 3 FLV0P FLV0P 3 BLV1N BLV1N
19 18 RX2N 3 Screw Hole 18 16
20 19 RX2P Test Pad 3 FLV0N FLV0N 19 17
RX2P 3
21 20
RXCLKN
GND
Circle 20 3 BLV2P BLV2P
BLV2N
18
1
22 21 PWMO 21 3 BLV2N 19
RXCLKP RXCLKN 3 FLV1P
1
23 22 Test Pad 3 FLV1P 22 20
RXCLKP 3 PP4
1
24 23 GND 3 FLV1N FLV1N 23 3 BCLKP BCLKP 21
1
25 24 RX3N R2 24 3 BCLKN BCLKN 22
RX3P RX3N 3 GND
26 25 RX3P 3 1 1 25 23
27 26 GND 3 FLV2P FLV2P 26 24
28 27 R13 0402/0R/5% 0603/0R/5% 3 FLV2N FLV2N 27 25
29 28 R12 0402/0R/5% PWM_I 3 28 VDDD 26
PWM_O 3 Screw Hole
30 29 29 27
31
32
30 Circle 3
3
FCLKP
FCLKN
FCLKP
FCLKN
30
31 5 GM8 GM8
28
29
R243 32 5 GM9 GM9 30
32
PWM_I PP5 R230 33 5 GM10 GM10 31

34
33
R3 VCOM
C C
VCOMS 0402/0R/5% 34 5 GM11 GM11 32
GND 4.7k GND VCOMS VREF 0402/0R/5% 5 GM12 GM12
1 1 VREF 35 33
GM13
1
36 5 GM13 34
0603/0R/5% R234 VDDD 37 5 GM14 GM14 35
1
N14 Screw Hole 38 VDDA 36
RX0N
Circle 5 GM8 GM8
VCOM
1 I/O1_3 IC2 6 39 37
5 GM9 GM9 40 38
2 5 5 GM10 GM10 41 VCOM 39
GND VCC 5 GM11 GM11
RX0P 42 40
3 4 5 GM12 GM12 43
I/O3_2 IC1 5 GM13 GM13 44
41
42
ESDA6V8UF 5 GM14 GM14 45
VDDA 46
VDDA 47
48
49
N12 VCOM 50
RX1N 1 6 RX2N
I/O1_3 IC2 XP2
51
52
2 GND VCC 5 LVDS Test pad XR
VIN12V
RX1P 3 I/O3_2 IC1 4 RX2P XL
RX0N
Test Pad ESDA6V8UF RX0N
VIN12V 1 1
1
Test Pad
N13
RX0P
1
VCCI F1 VIN12V RXCLKN 1 6 RX3N

I/O1_3 IC2 RX0P 1 1
1
3216FF/1206/3A 2 5
GND VCC
C1 C2 C3
0603/100n/25V/X5R RXCLKP 3 4 RX3P
Test Pad
RX1N
Distance of the both test pad center is 2.0mm
I/O3_2 IC1
2
RX1N
ESDA6V8UF 1 1
1206/22u/16V/X5R
Test Pad
1206/22u/16V/X5R
RX1P GND
RX1P SCL SDA GND3
1 1
XP5
1
Test Pad
1 S_SDA R29 0402/0R/5% M_SDA M_SDA RX2N
S_SCL 1
S_SDA 1
1
2 S_SCL R28 0402/0R/5% M_SCL M_SCL 3 RX2N
B 3 R30 0402/0R/5% WP
WP
3
3
1 1
B
GND
4 Test Pad
5 GMI2C_SCL GMI2C_SCL5
GMI2C_SDA RX2P
6
GMI2C_SDA5 RX2P
7 1 1
8
9 Test Pad
RXCLKN
RXCLKN
1
11
10
1
WP Test Pad
WP 3 RXCLKP
RXCLKP 1 1
Test Pad
RX3N
RX3N
1 1
Test Pad 　春　筿　　Τ　そ　
RX3P
Title
RX3P 1 HE315DH-B11
1
Test Pad DWG NO <OrgName> DATE
2010.9.13
2
A2 D
6
A A
5 4 3 2 1
5 4 3 2 1
GMI2C_SDA 5
GMI2C_SCL 5
LVDS terminator, close to TCON T33V
PWM_I 2
PWM_O 2
T33V
BCLKN 2
BCLKP BCLKP 2
BLV2N 2
BLV2P 2
R7
RX0P RX0N
C78
T18V
T33V
XTAL_O
T18V
XTAL_I
0402/100nF/16V/X5R
OD_CTL
PWM_O
0402/100R/1%
GMI2C_SDA
M_SDA
GMI2C_SCL
M_SCL
PWM_I
R141
BLV2N
NC/0402/4.7K/5%
BLV2P
BCLKN
R8 N8
D RX1P RX1N 1 8 D
A0 VCC WP
2 A1 WP 7
0402/100R/1% 3 6
A2 SCL
4 Vss SDA 5
R9 R74
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
N7 RX2P RX2N 24LC256-I/SNAT24C256N 0402/51K/5%
VDD_PLL
I2C1_SCL
GMI2C_SCL
XTAL_I
XTAL_O
DPWM_I
DPWM_O
OC_CTL
VCCIO33
VDD18
I2C1_SDA
GMI2C_SDA
RSB2N
RSB1N
RSB2P
RSB1P
0402/100R/1%
R18 0603/13K/1% R11
TST_PGM 1 48 PI
RESET TEST PI RX3P RX3N
2 HWRSTN AVDD3V_LV 47 T33V R15 0402/0R/5%
2 S_SCL S_SCL 3 I2C2_SCL PVDD_LV/VDDD_LV18 46 T18V
EE_SCL M_SCL
M_SCL
2 S_SDA S_SDA 4 I2C2_SDA A/VSSD_LV/PVSS_LV 45 0402/100R/1% 3
2 RX0N RX0N 5 44 BLV1N
LV0N RSB0N BLV1N 2 R10 R14 0402/0R/5%
2 RX0P RX0P 6 43 BLV1P EE_SDA M_SDA
LV0P RSB0P BLV1P 2 M_SDA
2 RX1N RX1N 7 42 BLV0N RXCLKP RXCLKN 3
LV1N RSG2N BLV0N 2
2 RX1P RX1P 8 41 BLV0P
LV1P RSG2P BLV0P 2 R76
2 RX2N RX2N 9 40 FCLKN 0402/100R/1% T33V
LV2N RSG1N FCLKN 2 0402/4.7K/5%
2 RX2P RX2P 10 39 FCLKP
LV2P RSG1P FCLKP 2 R75
2 RXCLKN RXCLKN 11 LVCLKN EVEN_FRAME/FSTH RSG0N 38 FLV2N
FLV2N 2 0402/4.7K/5%
2 RXCLKP RXCLKP 12 LVCLKP RSG0P 37 FLV2P
FLV2P 2
2 RX3N RX3N 13 36 FLV1N WP
LV3N RSCLKN FLV1N 2
2 RX3P RX3P 14 35 FLV1P WP 3
LV3P RSCLKP FLV1P 2
15 34 FLV0N
VSSPHX/VSSLHX RSR2N FLV0N 2
VSSIO/VSS
FLV0P
T33V 16 33 FLV0P 2 HX6710 Crystal
PWR_ON
VDDLHX33 RSR2P
VCCIO33
GVOFF
RSR0N
RSR1N
RSR0P
RSR1P
VDD18
EE_SCL1 EE_WP1
AGEN
CPV
POL
STV
EE_SCL 1 WP 1
OE
TP
C7 1 1
C HX6710-B00MLAG 0402/1M3/5% XTAL_O Test Pad Test Pad C
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
EE_SDA1 GND2
2
0402/22pF/50V/X5R
Z2 EE_SDA 1 GND 1
R27 1 1
JAS14C
FSTH
C6 Test Pad Test Pad

FSTH1
1
XTAL_I
T18V
T33V
VDDD1
TST_AGE
1
TGVOFF
1 T33V
0402/22pF/50V/X5R 1
TCPV
1
TTP1
TOE
POL
STV
Test Pad Test Pad
Distance of the both test pad center is 2.0mm
TCON option function Close to TCON

HX6710 Power & Decoupling _close to each pin_
T33V T33V T33V T33V T33V T33V T33V T33V T33V T33V
V33V_TCON
PIN54 PIN47 PIN23 PIN16
L6 BLM18PG121SN1 R63 R71 R77
1
B R22 R17 R20 R66 R69 0402/4.7K/5% 0402/4.7K/5% 0402/4.7K/5% B

R16
C55 NC/0402/4.7K/5% NC/0402/4.7K/5%
C13 C12 C54 C56 0603/4.7K/5%
NC/0402/4.7K/5% NC/0402/4.7K/5% NC/0402/4.7K/5%
0402/100n/6.3V/X5R 0402/100n/6.3V/X5R 0402/100n/6.3V/X5R0402/100n/6.3V/X5R
2
OD_CTL TST_AGE TST_PGM POL CPV PWM_I GMI2C_SCL GMI2C_SDA RESET
NC/0603/1u/6.3V/X5R
V18V
R21 R73 C11
PIN53 PIN46 PIN21 PIN62 T18V
0402/4.7K/5%
R68
0402/4.7K/5%
0402/4.7K/5%
R70 R72
0603/1u/16V/X5R
L7 BLM18PG121SN1 NC/0402/4.7K/5% NC/0402/4.7K/5%
C19 C20 C53

C77
0402/100n/6.3V/X5R 0402/100n/6.3V/X5R 0603/1u/6.3V/X5R
0402/100n/6.3V/X5R
Control signal & test pad _Close to TCON_

N9 V18V N11
T33V 1 VDD VSS 8 TP STV
VDDD VDDD
3 VIN VOUT 4 V18V
Test Pad Test Pad
R235 100R
2 C74 2 7
VOUT 2 TP1 CLKIN ICSPDAT
ADJ
C5
1
1
R238 100R R32 0402/22R/5%
0805/10u/6.3V/X5R0402/100n/6.3V/X5R R236 100R TTP1
2 TP1 2 STV
1
1
3 6 T33V
2 POL CLKOUT ICSPCLK POL_OUT
2 POL CPV
1
LD1117A-1.8AZ1117H-1.8 R237 100R R240 4.7k Test Pad Test Pad

A A
2 STV 4 VPP COUT 5
　春　筿　　Τ　そ　
1
1
R35 0402/22R/5%
PIC12F609-I R241 TCPV
2 POL 2 CPV
1
1
4.7k VGH_CTL OE Title
HE315DH-B11
STV Test Pad Test Pad
3
R239 4.7k
R242 NC/4.7k C80 DWG NO <Doc>
<OrgName> DATE 2010.9.13
1
1
POL POL_OUT VD8 R214 0402/22R/5% R213 0402/22R/5%

MMBT3904LT1 0402/100n/6.3V/X5R TGVOFF TOE Size Checked Designer Drawer Rev SHEET
4 VGH_CTL
2
3
A3 D
6
5 4 3 2 1
10 9 8 7 6 5 4 3 2 1
R38
2 1
PWM POWER NC/0805/0R/5%
VDDA1
Test Pad VDDA
VIN12V
13.5V
1
R39 L4 LTRH6D28-100 VD1 VD2 AO3401L
1
VIN12V +12V 1 2 VFB 2 3 R40
VFB2 VDDA
C25
1206/0R/5% B340 C32
C22 C23 C24 R41 C26 C27 0805/0R/5%
R42 0603/100n/25V/X5R
0805/10u/16V/X5R 0603/100n/25V/X5R 0402/0R/5% 0805/10u/16V/X5R 0805/10u/16V/X5R C28 C29
0805/10u/16V/X5R 0805/1u/16V/X5R C30
1
D
0603/47K/5%
0603/100n/25V/X5R
R43
0603/100K/5%
0805/10u/16V/X5R
0805/10u/16V/X5R
D
2
R44
C31 0402/750K/1%
0402/22p/50V/X7R VDDA=1.146*(1+R44/(R46+R47))
1
R45
0603/100K/5%
2
R46
0402/68K/1%
GD
R47 0402/750/1%
2 1
1
C34 0402/22n/25V/X7R
R48 0402/0R/5% N3
C33 0402/22n/25V/X7R
1 FB SS 28 C35 0402/22n/25V/X7R
C145 0603/470n/25V/X7R 2 27 GD
VFB COMP GD
2 1 3 OS DLY2 26 C36 0402/10n/25V/X5R
SW 4 25
SW1 DLY1 REF
5 SW2 REF 24
GND 6 23 GND
PGND GND C37 0603/1u/16V/X5R
C38 0805/1u/50V/X7R 7 22 +12V
+12V PGND AVIN +12V
8 SUP VINB 21
1
9 EN2 VINB 20
C65 2 1 +12V R49 0402/0R/5% 10 19
DRP NC
BAV99LT1 NC/0603/470n/25V/X7R 11 DRN SWB 18
2
C39 0402/100n/25V/X5R 12 17 C40 C41
FREQ BOOT
2NC/0402/0R/5%
1 2 13 FBN EN1 16 0805/10u/16V/X5R 0805/10u/16V/X5R
3 14 15
GND
VGHP FBP FBB
Test Pad 31V R59 1
VGHP VD7 BD8160

VD3
29
1
R60 0402/0R/5% VFB2 1 C42 0603/470n/25V/X7R

C C
1
3 2 1 V33V1
2
C43 0603/470n/25V/X7R 3.3V Test Pad
2
C44 BAV99LT1 2 1 V33V
1
1206/10u/25V R50
0402/825K/1% C79
1
C66 0805/1u/50V/X5R +12V C45 L5 LTRH6D28-100 R51 R52 0603/0R/5%
1206/10u/25V FBP V33V V33V_TCON
2 1
R53 R54 FBN 0402/100n/16V/X7R 0805/0R/5%

R56
2
+12V C46 C47 C48 R57 0603/0R/5%
2
0402/0R/5%
0402/33K/1% VD4 VDDD VDDD
R55 0603/47K/5%
FBP B340 0805/10u/10V/X5R 0805/10u/10V/X5R
2
0402/0R/1% 0805/10u/10V/X5R
VGHP=1.213*(1+R50/(R53+R58)) C49
1
1
2
1
-5.76 V R58
0402/1.5K/1%
R228
NC/0402/1K/5%
VGL
VGL 0402/100n/25V/X5R
1
Test Pad
C50
1
R219 0402/10n/25V/X7R
BAV99LT1
1
R217 0603/0R/5% 0402/2.2K/1%

GND 2
3
V33V=1.213*(1+R219/(R220+R221))
2
R220
R227 0603/0R/5% 1
0402/1.16K/1%
2
VD5
2
R231
C51
C52 C143 R216 0402/560K/1%
21
NC/0603/220n/25V/X5R 0805/10u/16V/X5R 0805/10u/16V/X5R 0603/47K/5% R221
1
FBN
0402/51R/1%
2 1
CLOSE to SD1 R232
1
0402/110K/1%
1
B VGL=-1.213*(R231/(R232+R218)) R218
0402/1.5K/1%
B
REF
2
C140
0603/220n/25V/X5R
1
VGH 3-State
VGH VGHP
R223
_High active_ VGH
NC/0402/0R/5% N4 VGH 1
R225 0603/0R/5% VGH_CTL 1
1 VGH VFLK 8 VGH_CTL 3
R224 0603/0R/5% 2 7 GND Test Pad
VGHM GND R233
3 DRN NC2 6
4 5 VDDD
EP
NC1 THR VDDD

1
HA5402P 0603/16.2K/1%
9
R229 R226 R222

0805/2K/1% 0805/2K/1% C142 0603/32.4K/1%
C141
0805/1u/50V/X5R
1 2
0805/1u/50V/X5R
A R215
0603/20.5K/1%
A
2
Title
HE315DH-B11

4
Custom D
6
10 9 8 7 6 5 4 3 2 1
5 4 3 2 1
HX5200 Power
PROGRAMMING GAMMA EXT-GAMMA VOLTAGE _　Gamma
PIN9 PIN9 PIN20 PIN20
GM1
VREF
VREF
G8
G7
G6
G5
G4
2 GM1 1 1 11.95 R165 R158
1
G1 G8
C124 GM2 2 GM8 2
GND
C125 C115 C126 GM1
D 2 GM2 1 10.58 0603/5R1/5% 0603/5R1/5% D
2
0402/100nF/16V/X5R 1
2
0402/100nF/16V/X5R
N1
21
20
19
18
17
16
15
HX5200-A03BDCG GM3
1206/22u/16V/X5R 2 GM3 1 9.28
AGND
AVDD
GMA8
GMA7
GMA6
GMA5
GMA4
1206/22u/16V/X5R 1 R150 R148
G2 G9
GM4 2 GM9 2
GM2
G9 G3 VDDD
22 GMA9 GMA3 14 VDDD 2 GM4 1 1 8.64 0603/5R1/5% 0603/5R1/5%
G10 23 13 G2
GMA10 GMA2 GM5
C123
C122
G11 24 GMA11 GMA1 12 G1
0805/10u/6.3V/X5R 0402/100n/6.3V/X5R 2 GM5 1 1 8.10 R166 R145
P-GAMMA
G12 GND G3 G10

HX5200
25 GMA12 AGND 11 GM6 GM10 2

GM3 2
G13 VREF
26 GMA13 AVDD 10 2 GM6 1 1 6.317 0603/5R1/5% 0603/5R1/5%
G14 27 9 VREF
GMA14 AVDD_AMP GM7
R79
TG1 28 8 VCOM 2 GM7 1 6.317
AGND_AMP
GMA15 VCOM_FB 1 R172 R168

NC/0603/5R1/5%
VREF G4 G11
GMA16
GM8 2 GM11 2
VCOM
DVDD
GND 29 GM4
EP_GND
SDA
SCL
13.5V 12.4 2 GM8 1 4.5 0603/5R1/5% 0603/5R1/5%

A0
1
VDDA VREF
VREF GM9
1
2 GM9 1 1 3.946
C R78
R103
GM10
G5
R175
G12
R160
C
0805/68R/5% GM5 2 GM12 2
VDDD
SDA
TG1 TG1 0402/0R/5%

3.29 0603/5R1/5% 0603/5R1/5%
TG2
SCL
1 1 VREF 2 GM10 1 1
A0
VREF1 1
1 GM11
TG2 1 TG2
1
SCL R100 0402/0R/5% R88
R104
0402/0R/5%
2 GM11 1 1 1.978 R157 R174
GMI2C_SCL 3 0603/8.2K/1% C57 G6 G13
GM12 2 GM13 2
0805/10u/25V/X5R GM6
1
SDA R101 0402/0R/5%
GMI2C_SDA 3
2 VD6
2 GM12 1 1 0.573 0603/5R1/5% 0603/5R1/5%
GM13
TL431BCDBZR
2 GM13 1 1
3
VREF=2.495*(1+R88/(R94+R100))
R94 R163 R164
GM14
0603/2.05K/1% G7 G14
Reset IC for XAO function 2 GM14 1 1 0603/5R1/5%
GM7 2
0603/5R1/5%
GM14 2
R147 R102
VDDD XAO 0603/19R1/1%
XAO
0402/10k/5%
GAMMA Decoupling C
B B
GM1 GM2 GM3 GM4 GM5 GM6 GM7
VCOM Voltage VDDA
C59 C60 C61 C62 C63 C64 C72

R117
VREF 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R
0603/0R/5%
R116 VOP
0603/8.66K/1% GM8 GM9 GM10 GM11 GM12 GM13 GM14
C58
0603/100n/25V/X5R
C67 C68 C69 C70 C71 C73 C75

2
0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R 0402/100nF/16V/X5R

VR1
R128 0402/10R/5%
NC/2k 3 VCOMS
VCOMS
HX5200 Setting N10
RANGE=4.77~6.3V 1 OUTA VDD 8 VOP
1
VDDD VDDD VCOM

R126
2 7 VCOM
INNA OUTB
R118 VCOMS 3 6 0402/10R/5%
INPA INNB C76
R25 R26 0603/6.8K/1%
GND VCOMS 0805/10u/10V/X5R G_SCL1 G_SDA1 GND5
0402/4.7K/5% 0402/4.7K/5% 4 VSS INPB 5
A A
1
1
HX8902-C02AMAG
SCL SDA A0
1
1
GMI2C_SDA
GMI2C_SCL
GND
Title
R31 HE315DH-B11
0402/0R/5%
2010.9.13
5
Custom D
Distance of the both test pad center is 2.0mm 6
5 4 3 2 1
1 2 3 4
CN3 CON43 CON42

TCON CON51 FFC_60PIN FFC_60PIN RNF37 22x4 2
Connector62 BLVN0 1 BL0P
SHIELD BLVP0 3 4 BL0N
1 61 VSS_XON 61
Bank2_Sel 60 60 BLVN1 5 6 BL1P
1 POL_TCON0 2
TCON0
FL0P
POL ~ 59 59 BLVP1 7
RNF34 22x48 BL1N
A 1
STB_TCON5 3
TCON5 FL0N LC2 A
STB ~ 58 58 R BLVN2 1 2
BL2P
1
VST_TCON1 4
TCON1 FL1P LC1
VST ~ 57 57 BLVP2 3 4
BL2N
1
VCE_TCON3 5
TCON3 FL1N
VCE ~ 56 56 BLVCKN 5 6
BLCKP
1
TERMINATE_TCON8 6
TCON8 FL2P HC6
TERMINATE
~ 55 55 BLVCKP 7 8
BLCKN
LC ~
1
LC_TCON7 7
TCON7 FL2N 54
HC5 54
3D_EN
~
1
3D_EN 8
TCON2 53
HC4 53
9
TCON4 CLCKP HC3 RNF39 22x42
52 52 FLVN0 1 FL0P
BANK_SEL_B
1
BANK_SEL_B 10 Bank1_Sel CLCKN HC2
~ 51 51 FLVP0 3 4
FL0N
1
SCL 11
SCL 50 HC1
SCL ~
50 FLVN1 5 6
FL1P
1
SDA 12
SDA ST1
SDA ~ 49 49 FLVP1 RNF38
7
22x48 FL1N
1
nWR WP 13
WP L
nWR~
14
48 48 FLVN2 1 2
FL2P
LOCK6 47 47 FLVP2 3 4
FL2N
ROTATE
1
ROTATE 15
ROTA VCC
~ 46 46 FLVCKN 5 6
CLCKP
16
GPIO 45
VCC 45 FLVCKP 7 8 CLCKN
17
GPIO 44 44
18
GND 43
VCOM 43
19
GND 42 42
20 GND GMA14~
1 VGMA14 41
STB_TCON5 41
BLVN0 21
RV0N
1 VGMA13
40 POL_TCON0 1 3
LVSYNC GMA13~ 40 1 3
B LHSYNC
BLVP0 22
RV0P GMA12~
1 VGMA12
39
DP_sel B
39
BLVN1 23
RV1N
1 VGMA11
LDE
BLVP1
GMA11~
1 VGMA10
38
AVDD 38
C23 100nF/50V
24
LCK RV1P GMA10~ 37 37
R7_RXO0-_LV-
BLVN2 25
RV2N GMA9 ~
1 VGMA9
36
2 4
36 2 4
R6_RXO0+_LV+
BLVP2 26
RV2P GMA8 ~
1 VGMA8
35 35
27 1 VGMA7
GND GMA7 ~ 34 34
BLVCKN 28
RVCKN
1 VGMA6
VGMA14
R5_RXO1-_LV- GMA6 ~ 33 33 H5 HOLE
R4_RXO1+_LV+
BLVCKP 29
RVCKP GMA5 ~
1 VGMA5
32
VGMA13 32
1 VGMA4
30 GND GMA4 ~ 31
VGMA12 31
BLVN3 31
RV3N
1 VGMA3
VGMA11
R3_RXO2-_LV-
BLVP3 32
GMA3 ~
1 VGMA2
30 XL VGMA10
30 XR 1 3
R2_RXO2+_LV+ RV3P GMA2 ~ 29 29 1 3
R1_RXOC-_LV-
BLVN4 33
RV4N GMA1 ~
1 VGMA1
28
VGMA9 28
R0_RXOC+_LV+
BLVP4 34
RV4P AVDD 27
VGMA8 27
G7_RXO3-_LV-
BLVN5 35
RV5N 26
VGMA7 26
G6_RXO3+_LV+
BLVP5 36
RV5P 25
VGMA6 2 4
25 2 4
G5_RXO4-_LV-
FLVN0 37
LV0N 24
VGMA5 24
G4_RXO4+_LV+
FLVP0 38
LV0P 23
VGMA4 23
FLVN1 39
LV1N DP_sel
1 DP_sel VGMA3
G3_RXE0-_LV- ~ 22 22 H6 HOLE
C24
G2_RXE0+_LV+
FLVP1 40
LV1P POL_TCON0 21
VGMA2 21
C FLVN2 41
LV2N STB_TCON5 20 VGMA1 C
G1_RXE1-_LV-
20
G0_RXE1+_LV+
FLVP2 42
LV2P 19 19
43
GND VCOM ~
1 VCOM 18
1 3
18 1 3
B7_RXE2-_LV-
FLVCKN 44
LVCKN 17
BL0P 17
B6_RXE2+_LV+
FLVCKP 45
LVCKP VCC 16
BL0N 16
46
GND VCC 15
BL1P 15
B5_RXEC-_LV-
FLVN3 47
LV3N 14
BL1N 2 4
14 2 4
B4_RXEC+_LV+
FLVP3 48
LV3P 13 BL2P 13
B3_RXE3-_LV-
FLVN4 49
LV4N ST1 ~
1 ST1 12 BL2N 12
FLVP4 50 LV4P 1 HC1
B2_RXE3+_LV+ HC1 ~ 11 11 H7 HOLE
FLVN5 51
LV5N 1 HC2 10 BLCKP
B1_RXE4-_LV- HC2 ~
10
B0_RXE4+_LV+
FLVP5 52
LV5P HC3 ~
1 HC3 9 BLCKN 9
53
GND HC4 ~
1 HC4 8 8
1 54
GND 1 HC5 1 1 3
TP171 ~ HC5 ~ 7
TP167 ~ 7 1 3
1 55
GND 1 HC6 1
TP170 ~ 56
HC6 ~ 6
TP151 ~ 6
NC 5
12V_PANEL 57
1 LC1
5
VCC LC1 ~ 4
主题：创维5800-TCON6-0P10 TCON板之信号输入输出接口电路
4
58
VCC LC2 ~
1 LC2 3
2 4
3 2 4
1 59
D
TP173 ~ VCC
VSS_XON
2 绘制：袁亚文 2
D
1 60 VCC 1
TP172 ~ VSS_XON 1 1
SHIELD
~
TP169 ~ 1 62 日期：2014年8月10日 62
H8 HOLE
61 1
TP168 ~
1 2 3 4
1 2 3 4
A A
AVDD AVDD
L18
D70 VS TP (+15.77V@1.2A)
NR6045T100M Q8
12V_PANEL (+16V)
22uF/25V
22uF/25V
22uF/25V
22uF/25V
22uF/25V
22uF/25V
22uF/25V
AO3407
220nF/25V
10uF/16V
10uF/16V
10uF/16V
L-22UH
1N5822
0.1uF
C3216
C3216
C3216
C3216
C3216
R739
SOT23
NC
DO-214AA
330K
R697
R698
C78
C79
C73
C74
C75
C76
C77
C3216
C94 NC
0
C42
C44
C37
C72
C1
R704 R700 VS
0.1uF
330K
28
27
26
25
24
23
22
NC
39K 1%
R699
PGND_2
PGND_1
GD
SW_2
SW_1
VIN_2
VIN_1
29
C40
PGND
B B
C32 1uF/16V 1 21
VL CTRLP
3.3K 1%
R701
C33 0.1uF
2 20 R741 VCC
VCC VCC BOOT FBP
L17
TP 10K
NR6045T100M L1
(+3.3V@1A)
3 19
22uF/6.3V
22uF/6.3V
SWB FB
1N5822
L-22UH
0.1uF
R732
U8
NC
R733 4 18 R738 C92 2.2nF

CTRLN RT9990 COMP
R736
5.1K
DO-214AA
1uF/50V
0 47K
C86 NC
GND
C36
C35
C34
R734
100K
D69
QFN50P500X500X80-29
5 17 C91 0.1uF C93 10pF
FBN SS
主题：创维5800-TCON6-0P10 TCON板之电源管理电路
C81
VGL VGL VGL=-(VCC-Vfbn)R726/R731+FBN

6
FBB
绘制：袁亚文 CRST
16 C90 0.1uF
TP FBN=0 日期：2014年8月6日
D8
(-9.39V@0.12A) 7 15 C89 0.1uF
10uF/16V
C RST DLY VGOALVgoal C

TP
AGND
0.1uF
1N5819
Q6
NC_1
NC_2
NC_3
NC_4
NC_5
NC_6
1N4448HWS
1N5819
D9
VGL NC/FMMT3906 Vgoal

R742
1N4448HWS
3.6K
NC
5.6K 1%
C84
C83
SOT23
10
11
12
13
14
R726
9
R737
5.1K
NC/1uF
SOT23
R174 R779
C85
C82
R740
200
R0402
0
NC
1uF/16V
1uF/16V
Q9 Q7 R0603
C55 0.1uF
R176
1uF/6.3V
VCC
0
R735 R731
C0603
BZX284C6V2D
FMMT3904/PZT3904
SOD-80
10 2K 1%
NC
C52
C51
FMMT3904/PZT3904
ZD2
VCC
C88
C87
D D
1 2 3 4
1 2 3 4
A A
R281VS_BUFFER R259 10R R0402

Panel_VDD=16V VS_BUFFER VS_BUFFER GMA14 VGMA14
R771 100K 1% R260 10R R0402
0.10uF/50V
L36 GMA13 VGMA13
0.1uF/50V
VS_BUFFER VCOM_A
22uF/50V
100K 1%
FB/60R/3A 10K 1% R261 10R
R280
R0402
GMA12 VGMA12
GMA11 R262 10R R0402

VGMA11
C496
C462
C463
GMA10 R263 10R R0402
VGMA10
32 31 30 29 28 27 26 25 33
R265 10R
VCOM_OUT
GMA9 VGMA9
VCOM_ADJ
VCOM_FB
R0402
AVDD
AVDD
AGND
SET
AGND
EPAD
GMA8 R266 10R R0402 VGMA8
GMA1 1 24 GMA14
OUT1 OUT14 R268 10R
GMA7 R0402 VGMA7
B B
GMA2 2 23 GMA13
OUT2 OUT13 R270 10R
GMA6 R0402 VGMA6
GMA3 3 22 GMA12
OUT3 OUT12 R271 10R
GMA5 R0402 VGMA5
GMA4 4 U9 21 GMA11
OUT4 OUT11 R273 10R
GMA4 R0402 VGMA4
GMA5 5
OUT5
iML7991 OUT10
20 GMA10
GMA3 R275 10R R0402 VGMA3
GMA6 6 19 GMA9
OUT6 OUT9 R277 10R
GMA2 VGMA2
GMA7
主题：创维5800-TCON6-0P10 TCON板之伽玛校正电路
7 18 GMA8
R0402
OUT7 绘制：袁亚文 OUT8 R278 10R

GMA1 R0402 VGMA1
VS_BUFFER
日期：2014年8月7日
8 VSD
17
AVDD DVDD
R272 3.0K 1%
Tuner I2C 3.3V to 5V
AGND
DGND
STATIC_HI
nWR
SDA
SCL
BANK_SEL
AD
R346 0
R768 4.7K
R773 4.7K
R774 4.7K
9
10
11
12
13
14
15
16
QFT3
NC/4.7K
R772
NC_2N7002
C C
BUF_SDA SDA
R770 200K 1%
1uF/50V
BANK_SEL_B
nWR
VSD
DGND
R769 NC/4.7K
BUF_SDA
C523
R274 4.7K
R767 BUF_SCL R345 0

0.1uF/25V
VCOM_A VCOM
10uF/25V
10uF/25V
10uF/25V
0.1uF/16V
2.2uF/10V
R282 VSD L37 VCC
QFT4
10R
FB/60R/3A NC_2N7002
NC
R283 4.7K
BUF_SCL SCL
C505
C524
C525
C526
C459
C459
VSD
VSD
D D
1 2 3 4
1 2 3 4
L113 L115
L19 22uH CBW3216U800T VCC
R73 R117 AVDD 12V_PANEL CBW3216U800T 12V_PANEL VGH
SHD
NC
NC
NC
NC
R743 NC
1
2
L3216 SMD_10UH_6X6
470 1% 54.9K 1%
10uF/16V
C70C0603
C68C0805
NR6045T100M
1uF/50V
R52
R33
R36
R37
CBW3216U800T
C62 1uF/50V
4.99K 1%
A A
0.1uF
R169
C71
VST VST_TCON1
L114
C63 1uF/50V
L3216
VCE VCE_TCON3
10uF/50V
VGH VGH C64 1uF/50V TERMINATE TERMINATE_TCON8
(+29.74V@0.12A) TP D72 LC LC_TCON7
C66 1uF/50V C65 1uF/50V
DP_sel
NC/22uF/35V
IN5822
R53 4.7K
R27 4.7K
R30 4.7K
R31 4.7K
R744 4.7K
10uF/50V
10uF/50V
1uF/50V
R226 NC
100K 1%
DO-214AA
R223
C61
C80
C67
NC
C2
C3
SET1
SHD
LC1_1
STH1
SET2
SET3
C69
NC
41
30
29
28
27
26
25
24
23
STH1 22
21
3.48K 1%
R225
SET1
SHD
LC1
PMS
NC
GND
LXG
SET2
SET3
VGON
STH_1 R227 0 R0402
ST1
B R64 0 R0402 B
31 20 LC1_1 LC1
PGND NC
32 19 LC2_1 LC2_1 R71 0 R0402
LC2
FBG LC2
C50 2.2nFR56 12K 33 18 HC1_1 HC1_1 R201 0 R0402
HC1
COMPG CKH1
R59 NCP15WL683E03RC R62 120K REF 34 17 HC2_1 HC2_1 R208 0 R0402
HC2
R66 60.4K REF CKH2
R63 130K R61 620K VT 35
U4 16 HC3_1 HC3_1 R210 0 R0402 HC3
VT RT8922 CKH3
R65 100K 36 15
END GND NC
QFN40P500X500X80-41
3D_EN 37 14 HC4_1 HC4_1 R212 0 R0402 HC4

SET4 CKH4
VCC L117
VIN 38
主题：创维5800-TCON6-0P10 TCON板之电平移相转换电路 13 HC5_1 HC5_1 R214 0 R0402 HC5
VIN CKH5
CBW3216U800T 绘制：袁亚文
0.1uF/6.3V
1uF/6.3V
L3216
39 12 HC6_1 HC6_1 R217 0 R0402 HC6
VST 日期：2014年8月9日 CKH6
C49
C48
TERMINATE
40 11 STH2_1 STH2_1 R196 0 R0402
C VCE STH2 C
VGOFF
VCADJ
RATIO
AGND
GOAL
XON
ROT
VSS
LC
VCC VIN VST R130 0 R0402
VST_1 VST_1
10
1
9
L116
VCE R131 0 R0402
VCE_1 VCE_1 CBW3216U800T VGL
NC/4.7K
NC/4.7K
R187 NC/0
R206 NC/0
R129
R135
R209
R207
R128
10uF/16V
L3216
4.7K
4.7K
4.7K
R118 0 TERMINATE_1
0.1uF
ROTATE
R0402
TERMINATE TERMINATE_1
C53
C54
ROTATE ROTATE R121 0 R0402
LC LC_1 LC_1
CLK INV SET3
Vgoal XON R177 0 VSS_XON
NC/10uF/16V
Phase SEL SET2
NC/1uF/16V
C527
C528
Pre-Charge SEL SET1
0.1uF
C56
3D SEL 3D_EN
D5 D5
NC/4.7K
NC/4.7K
NC/4.7K
D D
R198
4.7K
R194
R193
R195
R192
4.7K
SOD-80
1N4448HWS 1N4448HWS
SOD-80
Vgoal
1 2 3 4

V 2 Diagram

Uploaded by

Copyright:

Available Formats

V 2 Diagram

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

V 2 Diagram

Uploaded by

Copyright:

Available Formats

What are some of the interconnect diagrams and schematics provided in the document?

What are some of the interconnect diagrams and schematics provided in the document?

What does the document discuss regarding the 32LS3500 interconnect diagram?

What does the document discuss regarding the 32LS3500 interconnect diagram?

V2-LCD/LED Screen Panel Repair Guide 147

47LV4400-Interconnect_MB Built-In T-con_Interconnect…… 178

T-Con Board Schematic/Circuit

HISENSE RSAG7-820-4159 T-CON Board with LED32K16 TV

SKYWORTH 5800-TCON6-0P10 T-CON Board Schematic…………...208

J1 "LED Driver" to P202 "SMPS" 2-4 2.68V

Ground F100 20 A_DIM 0V 0V OL

INV_CTL IC104 IC1000

SMPS Test P201 Open 1 PWR_ON 0V 3.4V 1.15V To Ft. IR Q400

*0% to 100% +2.5V_Normal

the on state. All Voltages should be produced.

18 3.41V 8 LED_R 2.71V 0V 2.01V 24Mhz

Diode Test = 2.72V

Q402 Power On/Off Q407 PANEL_VCC Q802 HDMI 1 D822 DDC_SCL2/SDA2

P705 Pin 18 Main or J2 Interface P705 Pin 19 Main or J2 Interface

LVDS CABLE WAVEFORMS:

2uSec per/div 460mV p/p 2uSec per/div 460mV p/p

Q402 Not On in STBY

AUDIO Mute 24Mhz

+24V PWR_ON:Q402: Turned on by Q401 turned on by IC101 RL_ON.

AUDIO Amp IC101

T8 1 PWER_ON 0V 3.38V 3.53V 1.16V 24 OL

Q405 Q4023 2 1 5V_USB

See Table for P2401

3.15A/250V STBY: 163V 3.3V_TU in

Q701 +- OL 1~5 24V 0.05V 24.17V 1.27V IC1002 D

7 Pin 14 is P_DIM, Pin 13 is A_DIM, Pin 11 is Error. Micro DS

Q101 IC1001 p/n: EBT61542109 CUSYLH/SUSYJK

D822 Q802 IC801

Resistance Function Voltage Resistance Function 8 LED_B 0V 0V 2.67V P501 2

37LK450 MAIN (BACK SIDE) SIMICONDUCTORS

LVDS CABLE WAVEFORMS:

2uSec per/div 811mV p/p 2uSec per/div 811mV p/p

Interconnect page 4 of 4 August 2011 37LK450 LCD-DV

IC408 +12V Power Det

Note: Components in Grey are on the

Q707 20 A-DIM n/c 1.53V Open 24 OL

19 12V 0V 12.27V Open For Voltages

14 S/T_SCL 3.34V 3.34V 3.1V Serial Flash X201 IC3703

2Msec per/div 8. CVBS

Intelligent Sensor Jumper Jumper

IC1001 Micro IC403 +1.10V_VDDC IC408 Power_Det IC1450 5V Short Protection

Q401 Power On/Off Q402 Power On/Off Q403 +3.3V_Normal

P703 Pin 40 or CN1 T-CON P703 Pin 41 or CN1 T-CON

LVDS CABLE WAVEFORMS:

2uSec per/div 811mV p/p 2uSec per/div 811mV p/p

For IC403, IC407, Q403 Voltage Distribution

+20V (21V) PWR_ON:Q402: Turned on by Q401 turned on by IC101 RL_ON.

AUDIO Amp IC101

Two Waveforms on the Right are Using the Tuner

LD1 Blue LED TFT Drive PWB Check

SET 0FF BOOT OK SET ON US1

Side Control Keys *Grayed out components on the back

LAST TWO WAVEFORMS ARE FROM THE TUNER