Kone Step Chain

KONE EcoMod Escalator
Maintenance Instructions
9 STEP CHAIN MAINTENANCE MODULE
Suggested maintenance schedule for Step chain Module is one to six times per year,
dependent upon escalator use.
9.1 Check and adjust automatic oiler
Step Action Note

1. Check brushes (1) for correct position at lubricating points on
step chain. Adjust brushes, if necessary.
2. Check oil level in reservoir (2). Fill with clean oil.
NOTE!Make sure oil is absolutely clean when filling automatic
oiler. Use escalator chain oil part number US505660032.
3. Check fitting connections for leakage. Tighten connections, if
necessary.
4. Set pulse length and time delay between pulses.
7-002057 (2010-02)
9.2 Setting pulse length and delay (501-B control system)
The pulse length and delay between pulses (for automatic oiler) are set by operational
parameters in the controller.
Pulse length (lubrication pump on time)
• Set operational parameter 19 (MINUTES) to 00.
• Set operational parameter 20 (SECONDS) to 02.
Delay between pulses (lubrication pump off time)
Delay between pulses is dependent on rise and whether the escalator is indoors or outdoors.
NOTE! Values below are starting point values for an INDOOR escalator with a vertical rise of
4.5 m. Parameters must be checked after first maintenance is completed and
adjusted accordingly.
NOTE! Values for escalators that are OUTDOORS and with different vertical rises may be
different.
• Set operational parameter 21 (HOURS) to 01.
• Set operational parameter 22 (MINUTES) to 10.
• Set operational parameter 23 (SECONDS) to 00.
707-183 (2002-10)
© 2009 KONE Corporation ASG-51.30.001-USK

All rights reserved. 62 (92) (B) 2011-05-25
9.3 Lube-free step chain
If required, the step chain lip track may be moistened by a spray in the running surface area.
• Spray application may be required if noise is

generated between step chain roller (3) and
lip track.
• Spray application may be along the entire
length of lip track.
• Spray application should be done once
before putting the unit into operation.
NOTE! Use only a high pressure semi-
synthetic grease (Rivotta SKD 3602),
based on metal soap without solid
additives for initial application.
7-002058 (2009-10)

9.4 Check step chain rollers
Complete the following to check step chain rollers.
Step Action Note

1. Make sure step band is clear of all
personnel and equipment.
WARNING!Serious injury or death can
occur from rotating step band. Make
sure step band is clear of all personnel
and equipment before attempting to
start escalator.
2. Disengage step band lock, switch ON
main power supply, and run the
escalator with hand held pendant
control or inspection switch.
3. Check for any damage or wear of step
chain rollers. Replace as required.
7-002065 (2009-10)

9.5 Check and adjust broken step-chain switches
Step Action Note

1. With main power supply OFF, physically depress switch actuator (1).
Listen for audible click of switch.
2. Check location of switch actuator (1) to trip bar (2).
• Switch actuator (1) should be in center of trip bar (2), and
should just touch trip bar surface.
3. If switch must be adjusted, loosen mounting screws (3) and adjust
switch actuator until actuator (1) is centered and just touches trip bar
(2).
4. Tighten mounting screws (3).
5. Make sure step band is clear of personnel and equipment, and turn
main power supply ON.
WARNING!Serious injury or death can occur from rotating step band.
Make sure step band is clear of all personnel and equipment before
attempting to start escalator.
6. Place a screw driver between switch actuator (1) and trip bar (2) so
switch actuates.
7. Try to run the escalator in BOTH directions using hand held pendant
control or inspect switch.
• The escalator should not start.
7-002055 (2009-10)

9.6 Check and adjust step chain tension (spring pack)
Check and adjust step chain tension as follows.

NOTE! Make sure step chain tension is adjusted uniformly on both sides of the escalator.
1. Position barricades, and remove access covers.
2. Turn main power supply OFF.
3. Engage step band lock.
4. In lower end pit, loosen outer jam nut (1).
5. Loosen inner jam nut (2) to remove spring pack compression and allow washer (3) to be
spun freely.
6. Turn inner jam nut (2) until washer (3) touches spring washers (4) (actual dimension of
spring pack without compression).
– Spring washers must lie together backlash-free without any pretension.
7. Measure and record the spring pack length (H) between washer (3) and washer (5).
8. Turn jam nut (2) until the correct tension dimension is set for chain type used.
– Determine the reduction dimension for chain type being set.
– Subtract reduction dimension from spring pack length (H) to determine correct tension
dimension.
For more information on reduction dimensions, refer to table titled: Reduction Dimension.
Example only:
The following dimension for (H) is theoretical only.
Spring length (H) - reduction dimension = tension dimension
140 mm - 5 mm = 135 mm
9. Tighten outer jam nut (1) to secure inner jam nut (2).
10.Repeat tension procedure for opposite side step chain.
11.Measure and record spring length (H) for both step chains (spring pack under tension
dimension).
12.Run the step band for one revolution.
13.Check spring length (H) for both step chains.
– If spring length differs from recorded dimension (spring pack under tension dimension),
reset spring length to recorded dimension.
14.Adjust step chain tension on opposite side of the escalator in the same manner.
15.Loosen hardware (6) and reposition the spring scale (7) so the pointer (8) is set to zero.
16.Disengage step band lock, turn main power supply ON, and replace access covers.
17.Run escalator for at least two revolutions, and make a visual check of the escalator before
returning the escalator to service.
18.Remove barricades, and return escalator to service.
Reduction dimension
Chain type Reduction dimension
16HDV 5 mm
22HDV 6.5 mm
30HDV 8 mm

5025314 (2011-05)
6
7
4
8
7
1
2 H
3
5
5025314(2011-05)


Kone Step Chain

Uploaded by

Copyright:

Available Formats

Kone Step Chain

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kone Step Chain

Uploaded by

Copyright:

Available Formats

KONE EcoMod Escalator

9 STEP CHAIN MAINTENANCE MODULE

9.1 Check and adjust automatic oiler

Step Action Note

9.2 Setting pulse length and delay (501-B control system)

© 2009 KONE Corporation ASG-51.30.001-USK

9.3 Lube-free step chain

• Spray application may be required if noise is

© 2009 KONE Corporation ASG-51.30.001-USK

9.4 Check step chain rollers

Complete the following to check step chain rollers.

Step Action Note

© 2009 KONE Corporation ASG-51.30.001-USK

9.5 Check and adjust broken step-chain switches

Step Action Note

© 2009 KONE Corporation ASG-51.30.001-USK

9.6 Check and adjust step chain tension (spring pack)

Check and adjust step chain tension as follows.

© 2009 KONE Corporation ASG-51.30.001-USK

© 2009 KONE Corporation ASG-51.30.001-USK

You might also like