NOTES: REVISIONS

125
1- FINISH EXCEPT AS NOTED. ZONE NUM DESCRIPTION E.C.N. DATE BY/APPR
2- FILLET RADII .010 EXCEPT AS NOTED.
3- HEAT TREAT PROCEDURE: 2.0 PRODUCTION RELEASE NF/20.10.2014
(1) STRAIN RELIEVE AT 850ºF FOR 2.755 .007
ONE HOUR.
(2) LIQUID CARBURIZE AT 1550ºF .0015 0.281 0.664+.002
32

22.5º
FOR ONE HOUR 20 MIN APPROX. 0.070 0.042 250 GRIND AFTER HEAT TREAT
TOTAL CASE DEPTH REALIZED 0.625 .005 .0015 O 0.437 .013 L

0.930
MUST BE .010/.015. AFTER FINISH MIN .663
(3) OLI QUENCH. .010 N .013 L 1.875
(4) SUGGESTED DRAW TEMP 0.155 .004 L
350 /375ºF AT HEAT FOR ONE HOUR .013 L 0.251+.001 0.100
1.180

1.8
CAM TRACK GENERATION:
(1) .3165 DIA +.003 THEORETICAL

30
CYLINDER TO BE USED. 0.255

°
20
(2) CYLINDER AT BEGINNING

R0
AND OPPOSITE END OF CAM TRACK.

.50
(3) CYLINDER TRAVEL .042 FROM
BEGINNING OF CAM TRACK.

02
(4) CYLINDER TWIST TILL REACH
DETAIL I 3.285 .007

0.678

X
22.5º AT .255 FROM BEGINNING
(5) CYLINDER TRAVEL .070 AT 22.5º SCALE 4 : 1

R0

60
N
L

R0.030
REACHING END OF CAM TRACK.
32

0.2
.0
.0
SECTION A-A 0.648+.002

R0
60

40
32 .004 L
1.179-.001
GRIND AFTER HEAT TREAT 4.345 3.014 2.500 0.127 .010
O R0.3
.004 L 00 00 0.380
R0.3
H VIEW F
G
1.720 250

A A
53°

0.150
45°

1.450

0.125
87
0.760
2X

0.1
0.0
75
250 .01
0
0.235

19° 2X
10° 0º30'

0.4035 .0015 0.640

87
59

59
0.070 45°
0.380 .003

0.1
0.1

0.1
2.675 .003 M P

45°
.004 N 45
VIEW H °
45 I
0.470 .005

°2
G

0.500
X SECTION G-G
R0

0.500 .005
2X
.0

B B
.008 N 60°
78

1.670
.0
03

90º 4º C SINK TO .18 , TAP

F 0.420 THRU 10-32 UNF-3B 0.500 .003 0.325
M 0.435 50
2 PLACES C R0.5
D
0.365

0.150 .005

1.730

0.128+.003
0.485
0.625 1.370
E E

0.188 SECTION C-C

0.485 .002
GRIND AFTER HEAT TREAT 0

9°
7
.002 O R0.0 C
R0 0.4 D 2.180
.02 16 1.565
04 .001 P
X SECTION B-B
0.485 .010

8 UNLESS OTHERWISE SPECIFIED

1,10 MATERIAL:

SSI DEFENSE
0.281

AISI 8620 STEEL DIMENSIONS ARE IN INCHES

82°

TOLERANCES:
60°

THREE PLACES ±.005 ANGLES ±30'

PLATING BREAK SHARP CORNERS .010 MAX. RADIUS http://www.ssidefense.com
125
0

SECTION E-E
.12

DWG. TITLE
SURFACE FINISH TO BE
R0

DRAWN BY DATE
.308 DPMS COMPATIBLE
R0 LA

PROPRIETARY INFORMATION NATHAN F.

4

20.10.2014
.0 CE

0.490 .015
P

The information contained within this drawing is the FINISH:

BOLT CARRIER
15 S

22.50° sole and proprietary property of SSI Defense and CHECKED DATE
0º30' 125 NATHAN F.
may not be copied, edited, disclosed to others or 20.10.2014
used for the purpose of fabrication; in full/part or
SECTION D-D in any form and manner without the prior explicit HEAT TREAT: ENGR. DATE SIZE DWG. NO. REV.
SCALE 2 : 1 written consent of SSI Defense
(contact@ssidefense.com)
Quench and Temper to Hardness
Specified
XX.XX.XXXX
DATE
A2 2.0
APPROVED
XX.XX.XXXX SCALE 1:1 WEIGHT SHEET 1 OF 1

CAD FILE: SSI_.308DPMS_BC_V2.0