Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Troub

Download as pdf or txt
Download as pdf or txt
You are on page 1of 55

SAMSUNG CONFIDENTIAL

A3LSMN981U Logic Block Diagram USB/SUB PCB Slave

RFCLK1_SDR865 (PMK8002)

MEMORY PM3003A
LP5 1.05V
LPDDR5 4x16bit LPDDR4x
UART 0,1 T/RX
RFFE

UFS_REFCLK
SDX55M RFFE

UFS memory UFS_RESET


PCIe Gen3
PCIE2_REFCLK_M/P
PCIE2_TXD_M/P QLINK_EN
RFFEs
MMPA (x2)
KLUDG4UHDB-B2D1 UFS_TX/RX_D0_N/P 2lanes PCIE2_RXD_M/P QLINK_REQ Tx/Rx
SDR865 HB LPAMID
UFS_TX/RX_D1_N/P PCIE2_SDX_RST_N WMSS_RESET
UFS3.1 TW TSB 128GB Contorl PCIe GRFCs
SDR_RFFE0_
PCIE2_SDX_CLK_REQ_N
SDX55 CLK/DATA
LFEMID
PCIE2_SDX_WAKE_N
AP: Cortex-A7 Modem 2G PA
(up to 1.5Ghz)
SENSOR Magnetic
AK09918C
MAGNETIC_I2C_1P8

RPM: Cortex-M3
Modem:
QET5100
RFFEs

Supplies
DRX LB/MHB
Hexagon DSP PA sense
GRIP GRIP_I2C_1P8
(up to 400MHz) 1.5+GHz (x2)
GRIP_INT AUDIO_UART_AP UHB
SX9360IULTRT RFFEs
CTI
AP_CTI_OUT SDX55
PROXY_I2C_1P8
(VIETMOBILE.VN) PROXY PROXY_INT
(Cross Trigger interrupts) AP_CTI_IN
TMD49073VBSH135R QLINK1_REQ/
GPS_5G_BLANKING
WMSS_RESETN
6AXIS_I3C_SDA/SCL_1P8 SDX2AP_STATUS QLINK1_EN/CLK
CAM_SPI
6Axis(Gyro,Acc) 6AXIS1_INT1 AP2SDX_STATUS
LPDDR4X SMR526
LSM6DSOTR 6AXIS1_INT2 IPC sideband signals (1.8GHz, 2Gb QLINK L0~12
(Error, Status) SDX2AP_ERR_FATAL Stacked die) 5G IFIC
SMR526_RFFE4
AP2SDX_ERR_FATAL
CLK/DATA
Barometer BARO_SCL/SDA_1P8
SDX_VFR_IRQ0/1
LPS22HHTR
CAM MCU
STM32G071E8Y6TR
HALL IC #1 AP2SDX_ERR_

SDXUART_RTX
LAA_EN_0/1
HALL_IN T

WLAN_COEX
PM8150C FATAL_2
COVER DET HALL
WIFI /BT ANT
PM8250 WLAN_MOTOR_

PMX55_PON_RESET_N
HALL IC #2

AP_PMIC_SPM IDATA/CLK
HALL_IN T2 SLEEP_CLK
PM8250
BT_PCM

PMK8002_PMIC_CLK
COVER DET HALL(SUB PCB)

RFCLK2_SMR526
SDX_SLEEP_CLK
BT_HOST_WAKE/UART

SDX_PS_HOLD

19.2MHz
WLAN_HOST_WAKE
MODEM & RF

32.768KHz
AUDIO MAIN MIC
SUB MIC
MAIN_MIC_CLK/DATA
SUB_MIC_CLK/DATA
PCIE0_REFCLK_P/M_WLAN
PCIE0_T/RX0_WLAN
PCIE0_RST_N
BT WIFI
LBEE5QC1RH-323
(Broadcom)
3RD_MIC_CLK/DATA PCIE0_CLK_REQ_N
3RD MIC Contact WLAN/BT_EN
SPK_OUT_FB_P
SPK_AMP_RST_N Audio
AMP_SCL/SDA_1P8
Codec
SPK SPK_AMP_OUT_P, N SPK AMP AMP_INT
CS35L40 AMP_I2S_BCLK, LRCK
SPK_OUT_FB_N AMP_I2S_D_IN, OUT
RCV_AMP_RST_N
RCV_OUT_FB_P

RCV RCV_AMP_OUT_P, N SPK AMP


CS35L40
MSM_QMODE_REQ
RCV_OUT_FB_N (MSM_BUCK_QUIET_MODE)
PMK8002
PMX55
(CLK Buffer)

DISPLAY QC AP
EL_ON1
SM8250-2-AB PM_FAULT_N 5G_PON_RESET_N 38.4MHz
Display PMIC
EL_ON2
MAIN SM3010
Display DISP_RST_N AP_PMIC_SPMI
DISP_TE / WUHB_INT
DATA/CLK WPC_DET, WPC_THM
MFC IC
POWER
DISP. Conn.

PLCD_MIPI(4 Lane)
FHD+ TSP_I2C_1P8 / TSP_INT POP LPDDR5 SEC PM8150C
1080x2400 UB_CON_DET
DDI : S6E3FA9 8GB VOL_UP
HALL_IN T2
HALL IC #2
BTP_INT_N
PM_FAULT_N
BTP_SPI, POC_SPI, COPR_SPI D1y @ 2736MHz
TSP FG_ERR UB_DDI_1P8_EN
PM8150C LDO(ET51518YB)
T-IC : Y771
DISP_DET VOL_DN
BTP PM8250 LDO UB_DDR_1P5_EN SLEEP_CLK PM_SLP_CLK_IN (32.768KHz)
(In-display) ( AP7340D-15FS4-7-71) PM_CLK_IN (38.4MHz)
WACOM_VSYNC
BIXBY_POWER VPH_PWR
Prime Goldx1 (3.09Ghz)
V_BATTERY_IN
Kryo585Gx3 (2.4Ghz) PM8250

Conn.
SPEN_I2C_1P8 IFC_SENSE_CC SYS
WACOM SPEN_IRQ_1P8/SPEN_PDCT_1P8 PMIC_PON_RST_N CHG_DET
BATT V_BATTERY

W9020 SPEN_RST_N/SPEN_FWE1_1P8
Kryo585Sx4 (1.8Ghz) AP_PS_HOLD CSP
4MB L3 LNBB_CLK1 (19.2Mhz)
CSN
4300mAh
SLEEP_CLK
PCA9468
CAMERA FLASH_LED_EN
FLASH_LED_TORCH_PWM
VIP_PWM
(Direct CHG) VBUS_IF

PM8250
PB02_IC_EN CAM PMIC PROXY_LED_EN DIRECT_IF_PMIC_I2C_1P8
S2MPB02X01-6030 SUB_PMIC_I2C_1P8/IRQ BOOST_EN BOOST 5.25V
FAN4861BUC53X AP
SUB_PMIC2_I2C_1P8
IF PMIC WPC_DET
PM8150C
CAM PMIC MOTOR_P/N
MAX77705 MFC PIN G_nEN(X)

S2MPB03X01-6030 VIB MST_EN/DATA_A


(MD15) WCIN_IF
P9320S MFC_I2C_1P8
WPC_EN
NFC_FLICKER_I2C_1P8
Flash LED + Flicker FLICKER_INT
SDX55M SDX55_DEBUG_UART_T/RX AUT1
AUR2
MFC_AP_IN T
MAX77816BEWP-T
NFC/WPC ANT
VBUS_IF
IFC_SENSE_INT_AP RES3
VTCAM_MIPI (4Lane) USB_AP_D_N/P
FRONT CAM DN1 JIG_ONB_CC
Conn.

VTCAM_MCLK / VTCAM_RST_N DP2


VBUS_OVP
AP_UART_TXD/RXD OVP LS

USB TYPE-C Conn.


UT1 VBUS_DISCHAR GING_EN/OVP_SHDN
VTCAM_AF_I2C_1P8 UR2
(10M) VTCAM_TELE_I2C_1P8 (VT10M/TELE) MUIC_D_N/P FPF3788UCX

CC1/2
SBU_SW_OE/SEL

EDP_AUX N/P SBU1/2


SWCAM_RST_N SW
Conn.

S-WIDE SWCAM_MCLK
SWCAM_MIPI C-PHY (3Lane)
SWCAM_I2C_1P8

SW_VSYNC NF C/WPC ANT


SIM_DET
CAM_AF_EEP_I2C_1P8 (WIDE AF) SDX55M SIM1_DATA/RST/CLK
NFC_ANT_1/2 SIM1
Main Dual Cam Conn.

WIDE MAINCAM _MIPI C-PHY(3Lane)


CP_ESE_RST

MAINCAM_RST_N
CAM_MCLK / CAM_CON_DET NFC
MAINCAM_I2C_1P8 (Wide Sensor) NA : SN110UV2

NFC & SIM


NFC_IRQ
TELECAM_MIPI C-PHY (3 Lane) NFC_CLK_REQ KOR : SN110TV2 SIM2_DATA/RST/CLK
NC
TELE VTCAM_TELE_I2C_1P8 (VT10M/TELE) ESE_SPI e-SIM SIM2
TELECAM_RST_N NFC_FLICKER_I2C_1P8
AP_MCU_I2C_1P8 NFC_EN
CAM_OIS_I2C_1P8 SE_ISO
SECURE_SPI_FLAG
REAR CAM CAM MCU MCU_nRST NFC_SWP1/2
6 axis CAM_SPI STM32G071E8Y6TR MCU_BOOT0_SWCLK
NFC_FIRM NFC_SIM_SWIO1/2

LSM6DSOTR
C1_NR_TDD_APT_N41 1T4R@NSA_2T4R@SA_0606(CHN NR APT)
SAMSUNG CONFIDENTIAL
C1_BLOCKDIAGRAM_Rev07_HWID9

LMH MMPA LMH MMPA HB LPAMid n41 UHB LTE+NR B26 / B8 n41 B5 n78
QM78041 LB + MB LB + HB MB + HB LB + n41 MB + n41 HB + n41 LB + UHB MB + UHB HB + UHB
QPA5580 #0 QPA5580 #1 QM78143 QM78078/9 QM78041
QPA5580#1 QM78041 QM78041
Plan A QPA5580 #1 QPA5580 #0 QPA5580 #1 QM78143 QPA5580 #1 QM78143 QPA5580 #0 QPA5580 #0 QPA5580 QM78143 QPA5580 #0 QM78078/9 QPA5580 #0 QM78078/9 QM78143 QM78078/9
QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#1 QPA5580 #1 QPA5580 #1
#1
TX0 TX1 TX0 TX1 TX1
QET5100#1 QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#1 QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#0 QET5100#1
B5/8/14/20/28 B5/8/12/13/26/71
ETDAC 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1
B1/2/3/4/25/66/34/39
LTE PLL 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1
B7/30/40/41
TX Chain 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1
LTE+NR B48 n5
n5/12/71
Reverse MB + LB HB + LB HB+ MB UHB+LB UHB+MB UHB+HB
n1/2/3/66
NR QPA5580 #0 QPA5580 #1 QM78143 QPA5580 #1 QM78143 QPA5580 #0 QM78078/9 QPA5580 #0 QM78078/9 QPA5580 #0 QM78078/9 QM78143
n41 QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#0 QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#0 QET5100#1 QET5100#0
n41 (APT 2nd) n41 (APT 1st) n77/78/79 ETDAC 0 1 0 1 0 0 1 0 1 0 1 0
PLL 0 1 0 1 0 0 1 0 1 0 1 0
TX Chain 0 1 0 1 0 0 1 0 1 0 1 0

QET5100 QET5100
ET#0 ET#1
MXD8621E

SDR865 PRX_TR_IN_10
SPDT
PRX10
(HIGH)
RF2

PRX_TR_IN_6
PRX6
(LOW)
LB_LTE_NR_path_CTRL1

Transceiver
RF1
BGSX44MA12 (GRFC18)

4P4T PRX SW LMSWKSGU-K21


RFFE5
PRX_TR_IN_0 MB_LNA_OUT1
PRX0 RFFE5

PRX2
PRX_TR_IN_2
PRX_TR_IN_4
MB_LNA_OUT2
HB_LNA_OUT1
LFEMid
PRX4
PRX_TR_IN_E HB_LNA_OUT2
sub 1 PRXE
5 (lb_L5_UWB_mb_hb) TRX_MB1

MB_RX OUT1
SDR_RFFE_1 QET5100_#0
ETDAC0_OUT2
LB LB DRX LNA_OUT_1 RFFE1
B3 TX B1
DRX6_A QPA5580 #0 (GRFC15)
AUX_MB2
MB_TX_BAND_CTRL
MMPA *LTE LB Roaming B1 TX B3

DPX202690DT-4343A1K SDR_RFFE_1

TX_TR_OUT0_MB ETDAC0_OUT2
QET5100_#0 LTE/NR MB_N41 2nd Tx RF1
DPX202690DT-4343A1K

Diplexer
SADRM1G17AB0F3K MB_RX OUT2
TX0_MB BGS12P2L6 RF2
HIGH

B25 TX ANT MB TRX ANT1 MHB


TX_TR_OUT0_GSM_HB SDR_RFFE_1 MB_TX_BAND_CTRL(GRFC15)
DRXF_A TX0_GSM_MB TX_PA_OUT_GSMHB RF1 B66 TX
B25/66

CPLIN1
LB DRX LNA_OUT_2 RF2 MB_RX OUT3

QAT5515 TX_TR_OUT0_GSM_LB TX_PA_OUT_GSMLB TX_PA_OUT_B8


TX_PA_OUT_B28 BGS12P2L6
HIGH

1.1 x 1.5 TX0_GSM_LB TX_PA_OUT_B14 TX_PA_OUT_GSMHB


AUX_MB1
GSM_HB
GPS_L5 TX_PA_OUT_B20
2G PA (SKY77365-11)
TX_PA_OUT_GSMLB B34/39TX CPLOUT COUPLING_LB_MB
SDR_RFFE_7 3.0 x 3.5 x 0.8 TX_PA_OUT_BC0_10_B5_B26_N5
SDX_RFFE_1 TERM

TX_PA_OUT_B3/66
TX_PA_OUT_B34_B39
TX_PA_OUT_BC1_B2_B25/1 RF1 B8 TX
MHB DRX MIMO LNA_OUT1 B8 BGSX22G5A10
7 BGS12P2L6
DPDT
RF2
NA/KOR DRX1_B HIGH B28 TX
B5/26
(GRFC14)
NR_PATH_EN B20 TX
B20

sub 5 DPX252690DT-5075C1K
MHB DRX MIMO LNA_OUT2
DRX3_B
B13 TX
B12

(UHB,n77/78) HIGH
RF1 B13 ANT LB
TRX ANT1 LB
NA/KOR : MHB DRX MIMO RF2

CHN : MB DRX MIMO (GRFC14) BGS12P2L6


SDR_RFFE_3 QET5100_#1 NR_PATH_EN LB_RX out B28
NA/KOR : N/C MHB DRX MIMO LNA_OUT3 ETDAC1_OUT2
BGS12P2L6 CHN : HB DRX MIMO DRX5_B B29Rx

QPA5580 #1 RFFE3 AUX_LB1

B14 SAW DPx AUX_LB2


MMPA LTE/NR LB_N41 1st Tx B1270 GSM_LB

GRFC4
MHB DRX MIMO LNA_OUT4
DRX7_B TRX_LB1 FRC
N41_SRS_DRX MIMO
n41_DRX2_SRS_ON
TRX_LB2
B26 TX
TERM
ANT4_N79_MIMO
13
CON14 MHB PRX_MIMO_LNA_OUT1
HIGH
NA: QDM5872 (3.4 x 2.6) TX_TR_OUT0_LB BGS12P2L6 16
CHN/KOR: QDM5873 LEGACY_LB
TX0_LB (GRFC14)
RF_MAIN_2
MHB PRX_MIMO_LNA_OUT3
NA/KOR DELETE TX_PA_OUT_B8
NR_PATH_EN 17 18
TX_PA_OUT_B71_N71 LFD181G65MPUF177
LNA Aux NR_LB 20 MHB PRX_MIMO_LNA_OUT4
SDR_RFFE_7 TX1_LB_JB TX_PA_OUT_B12_N12
RF_MAIN_1
TX_PA_OUT_B13 B12 TX
21 22 MHB PRX_MIMO_LNA_OUT2
TX_TR_OUT1_LB TX_PA_OUT_B5_B26_N5
SAYRH634MBA0C3K
DRX_ANT2_b21 SAFFB1G50KA0F3 JPN TX_PA_OUT_N28
NA/CHN/KOR DELETE
K B71 SAW DPx
BK30B07-24DS-0.35V

PRX_ANT3_UHB_n77_n78_MIMO
DRX_ANT2_UHB_n77_n78
BGS12P2L6 B14/71 : KOR/CHN DEL
NA
SDR_RFFE_7
UHB DRX MIMO
DRX15_B
GRFC5 MXD8643RM
n78_SRS_DRX_MIMO MXD8643RM SP4T TRX SW
5G_SRS_ON
QDM4850(2.0x1.6x0.7) SP4T TRX SW RFFE2 COUPLING_HB_N41_2ND DPX202700DT-4062A1

Diplexer
NA DELETE COUPLING_N79
RFFE8

SDR_RFFE_1 QET5100_#0
ETDAC0_OUT2 COUPLING LMB
COUPLING_n79 COUPLING_OUT COUPLING_Low LB
QM12114 FBRX_IN COUPLING N77_78
SDR_RFFE_3 COUPLING_High
RF4 QET5100_#1 TX: RFFE1 MB
sub 2 CHN N41 SA 1st QM78143 COUPLING N41_1ST
6 (MB/HB_L1_N41/N79_WIFI2.4G)
N79_SRS_DRX RF3
N79_SRS_PRX_MIMO RF2
RFCOM
ETDAC1_OUT2
RFFE3
LNA: RFFE5
N79_SRS_DRX_MIMO RF1 n79
PRX14_A
HB PAMid
RFFE8
TX_TR_OUT0_HB
n79
TX1_5GH TX0_HB
TRX_ANT2_MHB

PRX3
QM78079 (5.0 x 3.0 x 0.8) NA/KOR DELETE
n79 NA/KOR COUPLING_HB_N41_2ND
QDM4870 (4.0 x 3.0 x 0.7)
LFD181G65MPUF177 PRX1
QM23341
NA: 2-66-30, 25-41, 2-66-7
CHN(HK): 1-3-7-40, 1-3-41, 39-41
N41 TRX Filter
HB_LNA_OUT1 LNA_OUT1
PA_LNA_B30_IN TRX1 N41_APT_2ND
MHB DRX LNA_OUT1 TRX2
LNA_OUT2
DRX0_A
NA/KOR DELETE N41_SRS_DRx
HB_LNA_OUT2 SAYEY2G31BA0F3K
NA/KOR
JPN DELETE MHB DRX LNA_OUT2
MHB_n41_ENDC_SW_CTRL DRX2_A
B8914 (GRFC3)
LOW LOW

MHB DRX LNA_OUT3 SDR_RFFE_5


DRX4_A NA/KOR
HIGH HIGH n79
BGS12P2L6 MXD8621E
DRX12_A
MHB DRX LNA_OUT4

13 sub 6
(B40/n79 mimo)
WIFI_2.4G_SUB2 KOR
DRXE_A
HFQRX2MJB-454
BGS12P2L6

(9) HIGH (GRFC5)

5G_SRS_ON
NA DELETE
KOR DELETE
n79_SRS_DRX
SDR_RFFE_7 NA
DRX_ANT2_b21 SDR_RFFE_5 NA/KOR DELETE NA
NA/KOR BGS12P2L6
TX1_HB1 UHB DRX (LFD213G75PAEF228)
b40_drx TX_TR_OUT1_HB1 DRX14_A
SFHG52AA002
DPX252690DT-5075C1K 1.1 x 0.9 NA DELETE
RFFE3 N38/41 HIGH (GRFC5)
NA/KOR 5G_SRS_ON
QDM4850(2.0x1.6x0.7)
NA/KOR DELETE
SDR_RFFE_3 QET5100_#1
LFD181G65MPUF177 BGS14MPA9 ETDAC1_OUT2 NA
n79_mimo RF4 n78_SRS_DRX
N41_SRS_DRX RF3 n41 TRX
RFCOM
RF2
QM78041 (5.0 x 3.7 x 0.8) SDR_RFFE_5
RF1 BGS12P2L6 NA DELETE
N41_SRS_DRX MIMO
RFFE3 PRX17_B UHB PRX MIMO
B7515
CHN N41
n41_Rx0

KOR DELETE COUPLING N41_1ST


NSA 1st / SA 2nd
HIGH (GRFC5)
5G_SRS_ON
QDM4850(2.0x1.6x0.7)
NA/KOR

N78_SRS_PRX_MIMO
GNSS_L1
GNSS_L1 SDR_RFFE_5
NA DELETE
BGU8019W SAFFB1G56KE0F3K W_GRFC_1 N79(M) BGS12P2L6
PRX15_B
1.1 x 0.9 1.1 x 0.9 GNSS_L5
GNSS_L5
- GPS_L5 HIGH (GRFC5)
NA DELETE
GPS1502LSAFFB1G17AA0F3K
NA/KOR DELETE HFQRX2MJB-454 5G_SRS_ON
n79_SRS_PRX_MIMO
BGS12P2L6 SDR_RFFE_7
n79(M) NA DELETE NA/KOR DELETE
DRX13_B

GRFC5
HFQRX2MJB-454 MHB_PRX_MIMO_LNA_OUT1
5G_SRS_ON PRX1_B
sub 3-1
8 (N77/78,B48) PRX3_B
MHB_PRX_MIMO_LNA_OUT2
n79_SRS_DRX_MIMO MHB_PRX_MIMO_LNA_OUT3
PRX7_B SDR_RFFE_5
SDR_RFFE_3 QET5100_#1 NA: QDM5872 (3.4 x 2.6)
ETDAC1_OUT2 MHB_PRX_MIMO_LNA_OUT4 COUPLING_N79
NA/JPN DELETE PRX5_B CHN/KOR: QDM5873 TX1
NA
Main 2 Main 3
N78_SRS_PRX_MIMO RF4
QM12114 SDR_RFFE_3(PA&ASM)
SDR_RFFE_7(LNA)
1 HB/(uhb_n77/78/79) MHB PRX_MIMO_LNA_OUT4
4P4T
B66 LNA4
B25/66
2 (HB)
N78_SRS_DRX RF3 UHB PRX PRX16_A ϕ 
RFCO
RF2 M NA/KOR
N78_SRS_DRX_MIMORF1 UHB TX TX1_UHB_5GLM MHB PRX_MIMO_LNA_OUT3 B25 LNA2 ANT1
NA/KOR HIGH
RFFE3 TRx 
port2

Mapping
(GRFC2)

Direct 
QM78078 (5.0 x 3.0 x 0.76) HIGH
MS-156C B41 N41_SRS_PRX MIMO
NA KOR/CHN DELETE RF Switch (GRFC2) MHB PRX_MIMO_LNA_OUT2 B7/41 LNA1
RFFE0 VIO ϕ  NA/KOR DELETE LFD181G65MPUF177 Main 4
B46
PRX12_A
SCLK
SDATA N41_SRS_PRX MIMO
MHB PRX_MIMO_LNA_OUT1
3 (MB/UHB/N77/78)
SDR_RFFE_7 ANT2
NA/KOR DELETE B30 ϕ 
QAT3516 LNA3
9 sub 3-2
WiFi 0 ANT B46
DRX10_A
W_GRFC_0/1/2/3/4/5/14/15/18/19
ANT S/W MIPI 
2.1
TRx 
port1
(WIFI 5G) WiFi 0_5GHz to WiFi module B46 from WiFi module SDX_RFFE_0
B7/30

sub 4 RFFE_0_slave for SDX55M


WiFi 1_5GHz to WiFi module B46 from WiFi module
RFFE_1_52MHz NA: 2-66-30, 25-41, 2-66-7
10 (WIFI 5G_2.4G)
WiFi 1 ANT
RFFE_2_52MHz
0 Main 1 CHN(HK): 1-3-7-40, 1-3-41, 39-41
LBEE5QC1RH-323 RFFE_3_52MHz (LB/MB)
RFFE_5_52MHz
RFFE_7_52MHz
4 Main 5
(N79)
QAT3555 RF_MAIN_2 ANT5_N79_MIMO_OPT NA/KOR DELETE
RFFE_8_52MHz 2 1
RFFE_9_26MHz Impedance Tuner
SDX_RFFE_0 RF_MAIN_1 PRX_ANT4_UHB_n77_n78_MIMO
6 FRC 5
VIO RF
1
RF
2
RF
3
MHB PRX_MIMO_LNA_OUT3 10
CON9 MHB PRX_MIMO_LNA_OUT2

RFFE0 VIO
DATA
RF
4 MHB PRX_MIMO_LNA_OUT4 12 11 MHB PRX_MIMO_LNA_OUT1
RFFE0
SCLK

MS-156C
SCLK RF
SDATA 5

ID0 RF
6
RF Switch
QAT3516 RF RF RF RF

ANT S/W
10 9 8 7

SDX_RFFE_0 BK30B0.6-12DS-0.35V
IF SUB PBA
Model :
Revision :
Manufacture Count :
Charge :
Contact :
Date :
Routing :
Resin :

VX_SETUP(2020-05-07)_HHP
Created date of PCB data : 2020/6/22 09:19:41

U4007

C3113
L3012

L3010

L3006
ANT3001

C4039

SOC9001

C4043
C2002

L2003

U3001
L4003
C3001

V3003 R5103
V3011

ANT7004
V11001

C9099

C3106 L3046 R5104


F2011
C4040

R5038

R5039

L3048
ANT7021

C3114
R4017

C4045 C4044

R5107 L2005 C2003


R4015 C4041
R5015
R5026

R5027
C4046

L4006

R5108
R4016
V7004

R5014

F2010
C3115

C3074

C3075

C3076

L4004

C4035
R4014
V7037

C4073
R3108

R3082

R3083

R3084
C4034

L2096

L2095

C2130

U4006
L2093
C3088
R3109

R3080
TP2001

C4036 L2094
ANT3007

V3013 C2181
SIM3000

L2103 L2215
V3006
U2121
F2006
JTAG6001

C9098

L2206
C9195
C2021
C3112

R5034

R5035

C2230
R5018

R5019

L2105
C2138

C2146

C2311 C2312
L3035

F2008
C2158
L2211

ANT7002 U2002
C2313

L3040 L3038
C3059

C2116

C2233 C2314 C2157


C2117
C3060

ANT7000

F3006 C8012
V7002

L3039
L8000 C2152
U2017

C8011 C2153
V7000

C8009 C2154

C8016 C2155
L8001
L2027

C8013
C3109

CON5001 C8008
L2028
JTAG6000

C2102

R2005
L2080

L2072

L2207
C2097

L2067
L2088
L2101

U2013
C2103

SC3000
R11008 C2106
R5109

R5110

C3085 L2063 R5100


C4047 C4022 C4018 TP4002

C3078 R5012
R5101
TP11030
C4011
C4021

C11009 C11034 C11033 C11010 C11011 C11018 C11035 C11037


U4003

TP12003
R5013 TP11029
TP_SDX_RESOUT_N

TP11028
R4006

R11006

TP4000

R3081 C4020 R5102


C2045

C4012

R12008
C3077

TP4006
TP11013
C4010

U4009 C4004 C4015


C4032

TP4005
R12007
U11000

TP11012

C4019
C4016 TP4008
C11002
C3079

C4009
C2040

TP11011
C4031

C4023 TP4004
C11001
C2043 C2038
V11000

C12044

TP4001
C11004
C4008 C12029
C4017

R4003

C11003
C4024 TP7022
C2048

U12000

U2006
C4013

R4005

L4001 L4002 C12065


L2038

C11023
C4051 C4052 C12043
C4026 C4027 C11019
R4052

C12045
R4051

R11010
C4053 C4054
L2078

C12054
C12058

TP12005

L2213 L2214 C2052 L2141 L2079 TP7014


C12039
JTAG6002

TP12006
C12046

TP7013
C12041
C3110 TP_SDX_FORCE_USB_BOOT

C12052
U7007
R5052

R5053

C7113
C2201

R4002

R4024

R4023
L2201

C12057
C2032

C2042

L2181
C2037

C12047
C2036

TP4010 TP4017 TP4011 TP3015 TP3032 TP3023 TP3000 TP7021 TP4018 TP5002 TP5003 TP8011 TP4007

L2202
C12042

C12040

C12059

C12056

C12030
C12031
C2203

C12048

C12027
C12033

C2202
R3085

C3087

R3087

TP11032 TP11019
L7023

C12055
L2204

L2203
C12053

C12028

C12032

TP11018 TP11021

U2007 C11029
HDC6000

C12051

C12049

C12050

R11007
R11005

R11004
R7012

R11000 TP11022 TP11016 TP11024


C11032 C11028
C11031
C11027

C11025

C11030
C6025

C7114
L7321

R11001
C2030 TP11023 TP11017
C7159

C7157

C12061
C2031
C6098

C6099

C11026
C7115
C7302
C7303

U7300
R6000

R6001

C3068
TP7003 TP8000 C6008 C12037
R5005

V5000 R13000 R5001 C6003 C6032


R3020
C3067
C12038
C7024 L7021
C5006
C7020
SC3001

USB_BOOT_B
R12005

ID_T
C5005
C7025
C7301

C7012 C7010
C5008
TP10000
C7026

C5007

UME6000
R6005
U7002

TH7000
C7008

C6097 C5022
C7016
C7071

R5003
C7070

C7000
TA7000
R7005
R7006

TP7002

R5009
C7013

L7000
R7007

R7004

TP5000

TP6006

TP6009 R7300 TP7018 TP_MFC_AP_INT TP7030 TP7216


L9009 L9006
R7010

R7207
C9032
L9001

TP10001
TP6008
C7015 C7205
TP6002 TP7031 TP7017

C7300
TP7001

TP6003
C9028 C9155 C9017 C9030
C7007

C9022
R7011

C7009 R7001

UCP500
TP6007
C5003
R7002 C9004 C9031
TP6005 C5004
C9020 C9027 C9026 C9016 L9002 C9029
R7015

R7014

C7005
C7006

C7017

TP7009

TP6004

R7017 C9021 L9015 C9054 C9025


TP6011
R5008
C7131

TP6010
C7018
C9065

L9023

TP6012

TP6001

TP6000

C7001
C7119
SOC9000
C9091

L9024
C5002

V7026 BOTHHOLE7007

C7135
C8026
C6001

C6000

C6024
C6009

C6022

R6004 R13002 R3014


U7005

C8029 C7044 C6023 R5022

TP7006
R5023
R5006

C5000

C5001

C7304
C8028 TP7005
R7029 L7001
R5017
R5007

C7121
L8003

R5016 R5036 R5037 C9012 C9011 R7003 DEBUG_CLK


TP7020
C9052 C9013 R9000 R13003 TP9010 TP9011
TP_PM7001 TP_PM7000
C8027
L7230

U8001
C7132

C7136 TP7028

TP_DP TP_DN
C4001
U4001
U4004

C4050 C7230

C7137
D4000

TH7001
R7230 ANT7005 ANT7008 ANT7020
C7233

C7235
C7004

L4000

U7011
C7120

C8024 C7129
C4002

C7232 R7232 C7234 L7229


R5024

R5025
R5106

R5046

R5105

C5019

C6007

C6083
C5017

C5018

C5015

C5016

R5004
C6006

R5000 C7231
C5012

C5013

C5011

C5010

TP7004 TP9000
C8022

TP10004
R4010
R7000

C5014 R7231
C4005

TP10003 TP8012
R4007
R7013

R4009
C5021

C5009

C5020

TP_CC1
ANT7007 ANT7016
TP_VPHPWR

C8023 L7231
R5066

R5067

R5064

R5065

R5062

R5063

R5061

R5060

TP8016 TP7300 TP9002

C7023 C7022 C4006


TP8015

R4004 C4028
C7002

C7003

TP_AP_RESOUT_N
TP9001

C4072
TP8013 TP8014

C4014 TP_VBUS_OVP TP_GND

USB_DN USB_DP

LFL152G45TC7C309(F3000) : IT'S W
rong Polarity possibility. Check
the Pin1
Model :
Revision :
Manufacture Count :
Charge :
Contact :
Date :
Routing :
Resin :

VX_SETUP(2020-05-07)_HHP
Created date of PCB data : 2020/6/22 09:19:41

ANT2002 ANT2000 C2301

ANT2008
MIC8000 ANT2007 ANT2005
V2001

C2304

ANT2006
L2301
V2005
C2307

C2302
C2179
L2021 L3019
L2007

SOC9003

C2008

L3024

L3023
ANT3000

L2011

L2302
C2016

V3014
C2004

C2001

L2004

C2303
C2180
C2226 C2310
C2224

C2306

L2303
C2222
C2223
U2000

L9017

L2000
C3105

C3099
L2209
C2014
L2018
L2019

C9094

ANT3005
SC3002
C2235
C9153

C2083
C2086
L3062
C9196 C2034
C9151

L2129

L2130
C2081

V3001
L2008

C9154

C2089
RFS2001 RFS3000
TP2005

C2011 C9093

V3002
C2080
L2116 C2165 C2266

U2014
C9152

C2005
TP2004

C8014

C8004

C2082
C2079

C2167

C2178
L2118
L9000 C9010 U2120 V7023
R8001

L2069

C2088
L2115
C9102

C9002
LED9000

C2100

C2168
L2117
C8005

C2107
U2019
C9111
L2066

C2094

C2087

C2058

C2056
C2268 C2024 L2029 L2065 L3020 C3103
L9021

L2182 L2076

L2200
C2200
ZD9001

BOTHHOLE7000

U12002
L9011 C2076
U2015

C2133
F2003 U2016
C2163
F3004
C9105

L2050

C2060
R9004

L2075
C2164 L2049 C2108
L2114 L2113

L2022
TH7003

L2012 BOTHHOLE7016

U2009
C9059

C2065
C2101

L2074

L3104
C2112 L2060

L3051
L2024
C2162
L2112

C2264

L3015
U2018 C2169

C2170
C2171 V7008

C2066
F2004
C2071
L3013

L3102
C2063 L3028
C2161

C2050

L2089

C2061
L2111 C2111

F3000
BOTHHOLE7012

L2142

V3007

V3004
C2059
C2051

C3036 V3005

L3030

ANT3004
L2025

L2026

L3103
U2004 C2007
C2020
ANT2004

C3044

L3021
L3022

L3026
C3023
C2118

L3014

L3016
C2228

C3107
C2231

C2110
C2096 C3055
L2070

L2306
C2119
TH3000
C3102 ANT3002
L2104 L2057
BOTHHOLE7010 U2001
C2229

TP2006
C2105 L2062 L2058 F3005
C4049
ANT2001

L2036

U3008
L2138

C3038
L3029 L3031

V3009
L2304

L2305

U2005

TP4014
C2069

U3000
C3000

L3044
TP4013

U4005
L3008
C2027

C2026

L3042
U2003

TP4012
L3000

L2034 ANT8000 C3002 L3005


C2232
L2035 C2006
TP3036
C2028

C2029

C8010 C8006 C2265 R2003


R2002

C2093
C2046
L2039

C4071 R3022

ANT2003
TP2003

U2010 U2011
ANT8001
L2098

R3012
TP2002

C3048

L2040
TP3031 TP3034
C2267

L2059

C2099 TP3033 TP3035


C2204 C2205
C3051
BOTHHOLE7011
SUS3000

L2056 TP3016

C2263
BOTHHOLE7015
BOTHHOLE7009 TP3021
F2002

TP3014

BOTHHOLE7005
TP4016
TP_UB6000 TP3018

TP4015
BOTHHOLE7014
C3050

C2207 TP3010

BOTHHOLE7013

(VIETMOBILE.VN)
L2054

TP3012

TP_UB

TP3029 TP3026

C2208 TP3030 TP3028

INP13000
TP3038

C7096 C7094 R7234


OSC7000
C11012

C11007

C12063

C12064
R5040

C9141

C11020
C3007
R9012

L3050

C3061
HDC11000

TP9009 TP_USART9000

C11021
C11042

C11016

C11015

C11013

C11024

C11022

C11017

U7003
R5041

C7083

C7084

C7072
C11041

L8002
TP9007 TP9006
R13001

C9096 C9097
C8019

C8018

C8020

TP_SWDIO TP_USART9001
C7033
C8015
U9009

C7098 C7066 L3041


C7147

C7097

TP11031 TP9008
C7062

C7061

R12004
C7110
TP12004 TP12000
C11039 C11006
C11040

C3011
C7064 C8001
C8017

L7020 C3072
C7191

C7087

U8000
C7054

C11000
C8002

C12010 C12000 R3106 R3105


C11005
R3107

C11046
C7067
R11011

L7019

C7055
R3103

C11045
R9013 R9002 R9003
C11036
C7145

L3101

L3100
C7065

C12002 U3010 U3011


R3102
U7001
L12002
L12003

L12004

C11038
C8000
R3104
C12011
C12067

C11014
R5020

R5021

R8000

C8003 R3100 C3100 R3101 C3101


C11047 C7170
C7171
L7018
C12066
C11044

C10013

C10014
L7012
L12005

CON5000 L10004
C10007

C10008

C10006

C10005
L7017

C12009
C12012 C12013
C7177 C7172
C10017

C12060 R12003
C7073 L10005
C7173

C7176
U12001
C12021

U10001

C12069
TP12001
C12020
C12005

C7174

L10001
C10016
C10011

C10010

C10009

C10012

L10003

C12016
C7175
C12022

C7063
L7014

L7015

L7016

C12024
C12026 C12062
C12025

L7013
C12023
C7107

C10000

C12019
BOTHHOLE7003 C12017
C10001 C10004
C7080

C12018 L12006 USB_BOOT_T


C10015
C7056
C7101

C7102

C7077

C12015
R7101

R7100

ID_B

C10002
C6035

L10002
C6040

C12007 C6061 L10000


C12014

C6049

R7018
C7074

C12068 C12004 C6096 C6046 GND_T


C12006
C6047

L7006

C6045 C7103 C10003


C6037
C6044

C6060

C7030

C6064
L7008
C7089

R10004
C6041

C6054

C6075 GND_B
C6028

C6017

C6014

C7104 C7029
L12001 C12036
L7005
C6095

C6090

R7021

L12000 C6053 C6058 C6051 C6059


R7024
C7164

C12008
C7166
C6091

C6093

C7082
L7009 C7162 C7163
L7007
C6027

C6015

C6016

C7165
C9000 C7039
C6092

C6094

C6086

C9063
L9025

C9073 C7038
C9068

C9067

C9131
L9003 C9057 C6036 U10002
C7105

C7106
C9074

C9142

C10901

C7045
C7305

C9019
C9075

C9137
C6055

C6077
C6089

C6073

C6070

C6013

C6012
C6088
C9046
L7010
C7161

C9042 C7046 C10902


C9133 C9033
C9081

C9008
C6010 C6011 C10903
C7213

C7214

C7215

C7217

C7216

U7000
C7212 C6034 C7053
C9034
U10003

C6080 C7079
C7201

U9002

U9008

C6026
ZD7201

C9084

C7160
TA7002

C7042
U7009
C7052

C7048

C7076
C9136

C9060

C9009
C9082

D7200 C9055
C6057
C6056

C6019 C6087 C6067 C6068 C6069 C6078


C7200

ZD7203 C9040 C7112


L7011
C7209

C9037
C7088
U7010

C7041
C7208

C10904
C7051
C9036
R7201

TA7003

TA7004

C6071

C6072

C6074
C6020

C6021

C6018

C9139
C6082

C7049

TA7005
R7202

C9072

C9071

R5033
C9070

L9026
C9132

C6050
C7218

C6052

C9043 C7168
C7031
R5032

L7002

C7040

C7043
C6062

C7167
R7200

C6029 C7169
C7204 R7203
C6048
C6030

C6031
C9140
C7222

C6042

C6063

C6081

C6004
C6038
C9135

C9130
C7090
ZD7002

C6043
C7021
C7220

TA7007
F7000

L7003

L7004

C9061 C6002 C7078


C7202

C7203

C9134
R7008

C6085

C6079

C6065
ZD7000

C6066 C6005 C6039


C9062 C7050
V7028
C7221

C7158
R5029

L9004
C6033
C7116

ZD9000 C7092
C7210

C7211

C7206

C7207

R7009
VBUS_T
C9058
C7219

R5028

ZD7202
TA7006 ZD7001
C9039

R9001
R9008 C9197 C7075

BOTHHOLE7008

BOTHHOLE7006

LFL152G45TC7C309(F3000) : IT'S W
rong Polarity possibility. Check
the Pin1
Model :
Revision :
Manufacture Count :
Charge :
Contact :
Date :
Routing :
Resin :

VX_SETUP(2020-06-20)_HHP
Created date of PCB data : 2020/7/23 14:59:38

SC17001
R15004

R15006

C14194 L15020
C14195
ANT16000

ANT16003

C14165 C14166 L14068


C14189

L15018

C15100
L15015

F15002
C15048

C14161
C15074
L14000

U14023
C15043

C15008

C15073

C15071
L14101

L15012
U14020
C14039

C14150

C15007
C15057

C15058

C15070 C14188 C15080


C15056

SOC17000
C14160

L15016
C15076 L14102 C15084
C15024
C15021

C15022
F15001

ZD16003 R16005 C16037 C16035 C16034 L14097 L14098 C15075


L14082
L14080

L14081
U14022
C15020

C15060
U15000

C15054
C15077
C14152
L14100

C14153
ANT16002

C15061
U14019 C15019
ANT16001 C14185 C15072
C15103
L15013

C15004
C15005
C15053
C15082
C14157
U14024 C15055
C14143

C14154 L14078

TP17003
C14198

C15018 C15078
C15051
L14029
U14015

C14023

L14073 C15046

L17004

L17003
C15006
SUS17000

C14057

L14072 C15050
C14022 L14010
L14065

L14069

C15047
C14155 C14156
C15067
C14149 C15023
R15009
L14090

ZD16002 C15065
C14148

C15064
C14142
L14077

L14096

C14175

C17028
C15062 R15008
C14179

C14139
C14199

C15063
U14003 C17030
U14018
C14151

L14075 C15009
R15010 OSC17000
U14025

C15066 R17008
C14169
C15037 R16019
L14079

C14144 R14005
C14013 R17007 C17029
L14071

C15026 C15017 C14187

R17022

R17010

R17009
C17007

L14066 R14000
C14131 L14054 C15000 TP14002
C14178
R14004

C15049

TP17000
C14086

TP17001
L14045

(VIETMOBILE.VN)
C17013 C17011 C17015 C17000
C15083
L15000

C15038
C15036
C14132

C14130

L14053

TP14003
L14052

L14042 C14079 C14080 C15039


C15012 U14008 U14017
C14182

C17004
C15011 R16021
C14081

C14191

C15052
C14076

TP14004

U17000
C14127
U14013

C15003
C15010 TP14005
R16018

C17001
C15045
C14084

C14075 F14006
C15069
C15002

C15030
C14126

C14118
GA17001

R16016
C14193

F14001
C14184

C14082 C15044

R17020
C14180
L14001

L14008

C15035
C17020
R15016

C14129
C14124

L14051

L14050

L14083
C14104

R17021
C15068
C14047
C14083

C14046 C14042
C17017
L14094

C15016

C15034
C15013

C15027

C15014

C15028

C15032

C15033

C15041

C15015

C15029

C15059
C15025
C14037

C15001

C15040

C15042

C15031

C14100
C14101 C14092 C17018
L14070

C14103

L14088 L14003
L14091
L14087

L14089
C14085
C14173 L14047 C14107 C14093
C14168
C14174

C14095
C14171

C17019
F14005
L14085
C14141

L14040 C14172
C14108
TH14001

C14167
U14004
U14014

L14092
R17014

R17015

C14164 C17009 C17016 C17014 C17008


C14183
L14074

C14163

L14064

U14021
R17042

C14158

C14099

L14059
C17003

C14089 L14028 C14159


C14170
R14003

C14088 L14027 C14109


R17012

R17011
C14138

L14067

C14106
C14136

L14060

L14046
C14105
L14034

C14162
C14110

L14093

TH14000
C14008

C14029

L14044

C14196

U14016
C14177
ZD14000

R14002

TP17002

U14002
L14062
C14186
C14102
L14033

C14017
C14007

C14026

C14028
L14041

L14086 C14112
C14137
C14097

C14096

C14012 C14006 C14021 C14014


C14069

C14111
F14003
C14061

L14063 L14019
U14006
TP14008

F14004
C14181
L14020

C14045

C14068

L14038

L14036
C14058

C14190

C14176
C14035 C14036
L14023
SOC14002
ZD17006

L14015
L14084
C14090

C14043
L14058

C14054
C14052 C14041 C14115 C14094
C14055

C14056

U14012

L14022 L14016
C14073 L14048 C14098
GA17000
C14197

C14091
C14134

U14009 C14048
C14070

L14031 L14005 C14121 C14116


C14087

L14043

F14002
C14059

L14026

U14007
C14002

L14021 ZD17003 ZD17005


C14004
L14004

C14122
L14049
C14063
L14061

L14024 C14000
U14000

ZD17007
R14001

ZD17004 ZD17008
C14001
C14062

C14117
C14145 U14001
C16039

C16042

C14011 C14123
F14000
C14024
L14011
C14140

L14009
C16003

C16002

C16001

C14003
C14147

C14010 C14005
C14146

L14030

L14032

SOC17002
SOC16000

L14006 C14016 C14009 L16001


L14002
TA16000

C14067
L14017

L14018

U14010
C14033

C14015 C14044 C14051


C16052

U16004
ZD16004

TP14007

C14064

C14074
C14066

L14035

L14037
C14065

C14053
C14077

C14019
L14039

L14012

R16012

C14040
C14060
TP16010
C17060

L14014 C14049 C14050


TP14006

L14025 ZD17010

SOC16001
ZD17009
C16055

C16024 L16000

ZD16011 ZD16013 ZD16018 ZD16019 C17040


V17027 L16002 ZD16008 ZD16009 R17026 R17028 C17035 L17006 R17033
ZD16010 ZD16012
ZD16016 ZD16017 R17032 C17052 C17053 C17051
C16027 R16310 R16311 R16312 R16313
C16053

C16025

SOC14000
SOC16002 SOC17003
C16021

CON17001
ZD16005
R16011

C16040
TP14009

R17029
R16318 C16023
ZD16014 ZD16015 C17034 L17007 ZD17021 C17062 C17050 C17038 C17039 C17049
8. Level 3 Repair

8-3. Flow chart of Troubleshooting.

Oscilloscope Digital Multimeter

Power Supply + driver, ESD Safe Tweezer

8960 & Spectrum Analyzer Soldering iron

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-1. Power on

Mobile phone does not power on

YES

Check the Battery NO Charging the battery by TA.


Voltage level. If the voltage has not reached over 3.5V,
Is it more than 3.5V? replace the battery first.
Even if replaced the battery, the battery voltage
has not reached 3.5V, then check the 8-4-23
Charging Part.
YES

Power-on the phone and YES


check the power-on Replace the Front assembly including display.
sound
or motor Vibration.
Sound or Vibration is
ok?

NO

When pressing Power NO


key, check if between Replace the POWER KEY FPCB
the R7231 and GND are
shorted
df

crack,open,etc)
YES

#1 Check the TP7004 is 1.8V


#2 Check the output voltage of U7000 and U7001
- R4004 = 3.3V
NO
Check the signal of - TP_UB6000 = 1.8V
AP_PS_HOLD = 1.8V
※ Each voltage level has ±10% margin
→ Replace the PBA If the voltage level is
abnormal,
YES

check the initial operation (8-4-3)

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-2. Motor

Motor does not work

Replace the motor to a new one

NO
Is there still the same problem? END

YES

Are the contact points damaged? YES Replace ANT113,ANT141 on the SUB PBA to new ones
or
(ANT113,ANT114 on the SUB PBA) the SUB PBA to a new one.

NO

Are the components damaged? YES Replace L121,L122 on the SUB PBA to new ones
or
(L121,L122 on the SUB PBA) the SUB PBA to a new one.

NO

Replace the ASSY SMD(Master+Interposer+Slave) to a new one

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-3. initial

Initial Failure

Re-download Software

Replace the PBA

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-4. SIM PART

SIM Card does not work

YES
Is the SIM card damaged?
Replace the SIM card to a new one.

NO

YES
Is SIM3000 on the master PBA damaged? Replace SIM3000 on the master PBA to a new one.

NO

Replace the ASSY SMD(Master+Interposer+Slave) to a new one

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-5. OTG

OTG does not work

YES
Is IF CtoC Cable damaged? Replace IF CtoC Cable to a new one.

NO

YES YES
Does it show abnormal voltage at the point below? Does it show abnormal voltage at the point below?

C4002 on the Master PBA : 5V C4001 on the Master PBA : 5V

NO NO

Replace Replace U4001 on the master PBA to a new one


the ASSY SMD(Master+Interposer+Slave) to a new one

Replace U7002 on the master PBA to a new one.


END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-6. Hall IC

Hall Sensor of cover_detect(U16004) does not work

YES
No

NO
Check the voltage
C16024, L16000 =1.8V Replace C16024, L16000

YES
No
Check the voltage
Check the voltage
without Magnet NO
C10092 =1.8V
U16004(4pin) =1.8V Replace U4008
with Magnet
U16004(4pin) =0V

YES
No

END

Hall Sensor(U200) does not work

YES
No

NO
Check the voltage
Replace C208, L200
C208, L200 =1.8V

YES
No

Check the voltage


Check theMagnet
without voltage NO
C10092
U201(4pin)=1.8V
=1.8V
Replace U201
with Magnet
U201(4pin) =0V

YES
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-7. 6-Axis sensor

6Axis Sensor does not work

YES
No

NO
Check the voltage
C4071, C4049 =1.8V Replace U7001

YES
No

NO
Check U4005’s package, smd status
(crack, open, short, etc.) Replace U4005

YES
No

Check 6Axis NO
MOSI, SCK, SCL, SDA pin
(SPI is OK?) Replace UCP500

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-8. Magnetic sensor

Magnetic Sensor does not work

YES

NO
Check the voltage
C4035 =1.8V Replace U7001

YES

NO
Check U4006’s package, smd status
(crack, open, short, etc.) Replace U4006

YES

NO
Check R5015, R5014
Replace UCP500
(I2C is OK?)

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-9. Barometer sensor

Barometer Sensor does not work

YES

NO
Check the voltage
C4047 =1.8V Replace U7001

YES

NO
Check U4009’s package, smd status
(crack, open, short, etc.) Replace U4009

YES

NO
Check R5109, R5110
Replace UCP500
(I2C is OK?)

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-10. Proximity/Ambient Light sensor

Proximity + Ambient Light Sensor does not work

YES

Check the voltage NO


L4004, R4016, C4040, C4041 =1.8V Replace U7001

YES

NO
Check the voltage
L4003, C4049, C4043 =3.4V Replace U9003

YES

NO
Check U4007’s package, smd status
Replace U4007
(crack, open, short, etc.)

YES

NO
Check R4015, R4017, L4006 Replace UCP500
(I2C is OK?)

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-11. Display

LCD is still off after PWR ON

YES

NO
Check Display Connector on MAIN
PBA Reconnect the SOC17003

YES

Check NO
VDD_DDI_3P0=3.0V (C17039)
VDD_DDI_1P8=1.8V (C17038) Replace the PBA
VDD_DDR_1P5=1.5V(C17050)

YES

Check
ELVDD 4P6=4.6V (C17052,C17053) NO
ELVSS_-4P4=-1.4~-6.6V(C17040,C17051) Replace the PBA
ELAVDD_7P6=7.6V(C17049)

YES

Replace the UB

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-12-1. TSP

Touch Screen does not work

YES

NO
Check TSP Connector on MAIN PBA Reconnect the SOC17003

YES

Check NO
VDD_TSP_1.8V (C17035) Replace the PBA
VDD_TSP_3.0V (C17034)

YES

Replace the UB

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-12-2. DIGITIZER

Spen functions are not working due to PBA.

YES

NO
Check Digitizer Connector on SLAVE Reconnect the SOC17000
PBA

YES

Check all decaps shorted GND or not.


NO (C17000, C17007, C17028, C17029, C17030)
Check
VDD_SPEN (C17007) is 3.3V Check L17003, L17004 is opened or not.

-> Replace component with defect.

YES

NO
Check Replace decoupling capacitor.
VDD_SPEN_LOW_1P8 (C17003) is 1.8V (C17003)

YES

NO
Check Replace 16MHz OSC
16MHz OSC output is normal
(OSC17000)
(C17011, C17015)

YES

NO
Check digitial signal of Wacom. Replace Wacom IC
(SPEN_SCL/SDA/PDCT) (U17000)

YES

Replace the PBA assembly (SUB+MAIN)

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-12-3. SPEN DETECTION

SPEN Insertion detection is not working.

YES

No
Check SPEN is working. Replace SPEN.

YES

NO
Check SPEN DET FPCB. (Crack) Replace DET FPCB.

YES

Check component on PBA.


(ZD17003, ZD17005, ZD17006, ZD17007) Replace ZD17003, ZD17005, ZD17006, ZD17007

YES

Replace U17000 or PBA

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-13. VT CAMERA

“VT Camera” function does not work

YES

NO
Check the Camera connector on Main

PBA Reconnect the SOC9003

YES

Check the voltage


NO
C9196,C9093,C9094: 2.8V

C9010: 2.8V Resolder or Replace U9008


C9111 : 1.05V

C9002 : 1.8V

YES

NO
Check the VTCAM_MCLK is
Reconnect the PBA
24Mhz (C9091)

Replace the camera module

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-14. Rear CAMERA

“Camera” function does not work

YES

NO
Check the Camera connector on Main

PBA Reconnect the SOC9000, SOC9001, SOC9004

YES

Check the voltage

Wide :
C9026, C9020, C9021 : 1.1V

C9012, C9031, C9032 : 2.8V,

C9025 : 1.8V NO
Tele : Resolder or Replace U9008, U9002
C9016, C9155: 2.8V / C9052, C9054 : 1.8V

C9011: 1.05V
Ultra Wide :

C9105 : 2.8V / C9098 : 1.05V

C9099 : 1.8V

YES
Yes
No

Check the CAM_MCLK is NO

19.2Mhz (C9004, C9065), Replace UCP500

YES

Replace the camera module

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-15. Finger Print

Finger Print Sensor does not work

YES

NO
Check the connection of
SOC17003 Reconnect or Replace the SOC17003

YES

NO
Check the voltage
C17062 = 1.8V Replace C17062

or Check U7000, INP18003

YES

Replace Front A’ssy(UB A’ssy)

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-16-1. Main MIC

Check main microphone function


In voice call Handset / Loud SPK mode
or voice recorder mode

Check IF USB Board NO


Set the SOC200 connection
Connection (SOC200)

YES

Check the signal of


NO
C242 = 1.8V
Resolder or replace the U7000 (PMIC)

YES

Replace the IF USB Board

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-16-2. Sub(2nd) MIC

nd
Check sub(2 ) microphone function
In camcording mode

YES

Check the signal of


C8004, C8014 = 1.8V NO
Resolder or replace the U7001 (AP PMIC)

YES

Resolder or replace the MIC8000

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-16-3. 3rd MIC

Check 3rd microphone function


In camcording mode. (Audio zoom)

YES

Check the signal of


NO
C16035 = 1.8V
Resolder or replace the U7001 (AP PMIC)

YES

rd
Replace the 3 MIC FPCB

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-17. Speaker part

Check the speaker function,


Play MP3 with maximum volume level

YES

Bottom speaker sound NO


Go to 8-4-18. Receiver part
` abnormal

YES

NO
Check IF USB Board replace IF USB Board

Connection (SOC200)

YES

Check the contact


NO
C-clips(pins) of replace IF USB Board
ANT200, ANT201

ANT200, ANT201
YES

Check the signal of


NO
C8022, C8023, C8024, Resolder or replace the U8001 (SPK amp)
C8027, C8028, C8029
= 11V

YES

Check the signals of NO


replace IF USB Board
L203, L204

YES

Replace the SPK module

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-18. Receiver part

Check the Receiver function,


In voice call Handset mode

Check the contact


NO
C-clips(pins) of Resolder or replace the ANT8000, ANT8001
ANT8000, ANT8001

YES

Check the signals of


NO
Resolder or replace the U8000 (RCV amp)
C8015, C8017, C8018,
C8019, C8020, C8003

YES

Check the signals of NO


L8000, L8001 Resolder or replace the L8000, L8001

YES

Replace the RCV module

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-19. BT/WIFI

BT/WIFI is not working

YES

NO
Check BT or WIFI fuction ON Enable BT or WIFI function.

YES

NO
Check the U7000
Check the Voltage on C3048
= 1.8V (Crack, open, damaged, etc)

YES

NO
Check the Voltage on Resolder or change
C3050,C3051, C3055= C3050,C3051, C3055
3.7~4.3V(VBAT)

YES

NO
Check the status of Resolder or change the
ANT3002,ANT3007,ANT3004, ANT3002,ANT3007,ANT3004,
ANT3005, ANT3001,ANT2007 ANT3005, ANT3001,ANT2007

YES

Check the Status of Resolder or Replace of


L3028L3029C3102L3030C3036V3004C3038L3031L3035C30 NO
44L3103L3102V3013V3005L3039C3060L3040L3038C3059V
3007L3019L3021L3022L3026L3020L3024C3099L3023V3001 defected(crack, open, damaged etc) components.
L3062V3014V3002C3105L3104L3051L3014L3013L3016C30
23L3015

YES

Resolder or change U3008

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-20. GPS

GPS is not working

YES

NO
Check GPS function ON Enable GPS Function in the setting.

YES

NO
Check the Antenna 1. Resolder or Replace
connection ANT2002, ANT2007

YES

well.Check(crack,open,etc) NO
L2021,C2008,RFS2001,L2024,C2268,C2133, Resolder or change the wrong element
L2022,C2096,L2057,C2105,L2058,L2062, (open, crack, deviation, etc)
L2098,C2093,L2056,L2059,C2099

YES

NO
well.Check(crack,open,etc) Resolder or change the wrong element
L15012, L15016, F15001, L15013, C15103 (open, crack, deviation, etc)

YES

NO Check OSC7000
Check 38.4MHz Clock at output
of OSC7000 (short, open, crack, etc.)

YES

NO Check CP PMIC(U12001)
Check the voltage on (short, open, crack, etc.)
L2056, L2063=1.7V

YES

Resolder or change U15000

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-21. NFC

NFC is not working

YES

NO
Check NFC function ON Enable NFC Function

YES

NO
Check the NFC FPCB Antenna Replace NFC Antenna

YES

NO
Check the Antenna connect Resolder or Replace SOC16000
SOC16000(Slave PCB)

YES

Check the voltage on Check AP Sub PMIC(U7001)


NO (short, open, crack, etc.)
VREG_L1C_1P8 = 1.8V
Check AP Main PMIC(U7000)
Check reference clock at (short, open, crack, etc.)
LNBB_CLK3 = 27.12MHz

YES

Check Master PCB


Check the NFC signal (L4001, L4002, C4053, C4054)
NO
at SOC16000 Slave PCB
(C16052, C16053, C16055)
(Keystring *#6328378# -> (crack, open, damaged, etc.)
PRBS test -> start)

YES

Resolder or Replace U4003

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-22. MST

MST is not working

YES

NO
Check the battery level
Charging the Battery
Battery >= 5%

YES

NO
Check MST FPCB Antenna Replace MST Antenna

YES

NO
Check the Antenna contact
Resolder or Replace SOC16000
SOC16000

YES

NO
Check voltage at C7201 Resolder or Replace U7009, U7010
(*#0*# -> MST test -> turn on
continuous)

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-23. Charging Part


Charging (Normal/Fast)

TA / USB Insert

Charging Sequence Start


Master PCB C4002 NO Reconnect TA or USB or
= 5V or 9V
Replace IF CtoC cable

YES
NO
Resolder or Replace U7000

NO Resolder or Replace
Check the voltage Master
Master PCB U4001
PCB C7001 = 5V or 9V

YES
NO
Resolder or Replace U7000

NO Resolder or Replace
Battery is Charging?
Master PCB U7002 (15W) or
U7005 (25W)

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-24. Charging Part


Wireless Charging (Normal/Fast)

Contact Wireless charger

Charging Sequence Start


NO Resolder or Replace
Master PCB C7205 =5V or
Master PCB U7010
10V

YES
NO
Resolder or Replace U7000

Check again about NO Resolder or Replace


Master PCB U7002
charging status

YES
NO
Resolder or Replace U7000

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-25. GSM 850/900, CDMA BC0/10, WCDMA B5/8, LTE


B5/8/12/13/14/18/19/20/26/28/29/71, NR_SUB6 n5/71 RX

NORMAL CONDITION
Catch the channel?

No

Yes
Check C103 or C115 ≤ -65 Check the ANT100,C103 or C115
dBm

No
Yes
Resolder or change
Check C113≤-65dBm
U110,C113

No

Yes
S Resolder or change
Check C14009 ≤-65dBm
C14019,C14009

No

Yes Resolder or change


Check L14006 ≤-65dBm S F14000

No

No
Check component
soldering status ok? Resolder or change
U14007 U14007

Yes

Yes
Resolder or change
Check C14044 Or C14049 C14014,U14010,C14044, C14049
≤-65dBm

No

No Resolder or change
Receiver is OK?
U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-26. LTE 14/71, NR_SUB6 71 RX

NORMAL CONDITION
Catch the channel?

No

Yes
Check C103 or C115 ≤ -65 Check the ANT100,C103 or C115
dBm

No
Yes
Resolder or change
Check C113≤-65dBm
U110,C113

No

Yes
S Resolder or change
Check C14009 ≤-65dBm
C14019,C14009

No

Yes Resolder or change


Check L14006 ≤-65dBm S F14000

No

No
Check component
soldering status ok? Resolder or change
U14007 U14007

Yes

Yes Resolder or change


Check C14044 Or C14049 C14014,U14010,C14044, C14049
≤-65dBm B14 : F14003, C14055, C14045, L14015, L14016
B71 : U14000,C14003, C14000

No

No Resolder or change
Receiver is OK?
U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-27. LTE B7/38/40/41 RX

NORMAL CONDITION
Catch the channel?

No

Yes
Check C112 ≤ -65 dBm Check the ANT101,C112

No
Yes
Resolder or change
Check C127 ≤-65dBm
U120,L124,C120,C127,

No

No
Resolder or change
Check L14093 ≤-65dBm
C14014,C14015,F14001,L14093

Yes
No
Resolder or change
Check CL14031 ≤-65dBm
F14002,L14024,C14053,L14031

Yes

No
Check component
soldering status ok? Resolder or change
U14013 U14013

Yes

No
Check L14050 or L14051 Resolder or change
or L14052 or L14053 F14006, C1427,C14130
≤ -65dBm

Yes

No
Resolder or change
Receiver is OK?
UCP15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-28. LTE B30 RX

NORMAL CONDITION
Catch the channel?

No

Yes
Check C112 ≤ -65 dBm Check the ANT101,C112

No
Yes
Resolder or change
Check C120 ≤-65dBm
U120,L124,C120,

No

No
Resolder or change
Check L14093 ≤-65dBm
C14014,C14015,F14001,L14093

Yes
No
Resolder or change
Check L14031 ≤-65dBm
F14002,L14024,C14053,L14031

Yes

No
Check component
soldering status ok? Resolder or change
U14013 U14013

Yes
No
Resolder or change
Check C14101 ≤-65dBm F14005, C14101, C14088

Yes

No
Check L14050 or L14051 Resolder or change
or L14052 or L14053 F14006, C1427,C14130
≤ -65dBm

Yes

No
Resolder or change
Receiver is OK?
UCP15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-29. DCS/PCS, CDMA BC1, LTE B1/2/3/4/34/39/66 RX

NORMAL CONDITION
Catch the channel?

No

Yes
Check C103 or C115 ≤ -65 Check the ANT100,C103 or C115
dBm

No
Yes
Resolder or change
Check C113≤-65dBm
U110,C113

No

Yes
S Resolder or change
Check C14009 ≤-65dBm
C14019,C14009

No

Yes Resolder or change


Check C14004 ≤-65dBm S F14000,C14004

No

No
Check component
soldering status ok? Resolder or change
U14007 U14007

Yes

No
Check L14050 or L14051 Resolder or change
or L14052 or L14053 F14006, C1424,C14126
≤ -65dBm

Yes

No
Resolder or change
Receiver is OK? U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-30. LTE B48 RX

NORMAL CONDITION
Catch the channel?

Yes
Check RFS3000≤ -65dBm ?
Check the ANT3005,C3099

No
Yes
Resolder or change
Check L2201 ≤ -65dBm ?
F3004, L2076,L2075,L2074, L3014, C3103

No

No
Resolder or change
Check C2098 ≤-65dBm C2098

Yes

Check component No
soldering status ok? Resolder or change
U2014 U2014

Yes

No
Resolder or change
Check C2100 ≤-65dBm C2100

Yes

No
Resolder or change
Receiver is OK?
UCP500

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-31. N41 RX

NORMAL CONDITION
Catch the channel?

No

Yes
Resolder or change
Check RFS2001 ≤-65dBm
ANT2007, C2008

No
Yes Resolder or change
Check L2076 ≤-65dBm L2201,L2054,F2002,C2205,C2204,C2267,C2
046,U2005,C2051,U2004,C2050,C2007,F200
4,L2022,C2268,C2133,C2024
No No

Check component No
soldering status ok? Resolder or change
U2007 U2007

Yes

No
Resolder or change
Check C2052 ≤-65dBm C2052

Yes

Check component No
soldering status OK at Resolder or change
U2006 U2006

Yes

Check component No
soldering status OK at Resolder or change
INP13000? INP13000

Yes

Check No
Resolder or change
C15971,C15973,C15075,C1 C2052
5082 ≤ -65dBm ?

Yes
No
Resolder or change
Receiver is OK?
UCP500

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-32. CDMA BC0/10, LTE B5/8/12/13/14/17/18/19/20/26/28/29/71, NR_SUB6 n5/71


DRX

NORMAL CONDITION
Catch the channel?

No

No Resolder or change
Check C2002 ≤ -65dBm ? ANT2000, ANT2002,C2224, C2001,
C2002

Yes

No
Resolder or change
Check C2069 ≤ -65dBm ?
F2011, C2003, F2010, L2095, C2069

Yes
No
Check component soldering status OK at Resolder or change
U2003? U2003

Yes

No
Check component soldering status OK at Resolder or change
INP13000? INP13000

Yes

No
Check component soldering status Resolder or change
OK at U22000
L15000 or C15083?,

Yes

NO
Resolder or change
Receiver is O.K? UCP500

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-33. LTE B48 DRX

NORMAL CONDITION
Catch the channel?

No

Yes
Check C112 ≤ -65 dBm Check the ANT101,C112

No
Yes
Resolder or change
Check C127 ≤-65dBm
U120,L124,C120,C127,

No

No Resolder or change
Check L14075 ≤ -65dBm ? L14075, C14139,C14199,C14144,C14061,C14054,C14052,
F14002,L14024,C14053, SOC14000

Yes

No
Check component soldering
status OK at U14018? Resolder or change
U14018

Yes

No

Check C14148 ≤ -65dBm ? Resolder or change


C14148

Yes

NO

Receiver is O.K? Resolder or change


UCP500

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-34. CDMA BC1, LTE B1/2/3/4/7/25/30/34/38/39/41/66 DRX

NORMAL CONDITION
Catch the channel?

No

No
Resolder or change
Check RFS2001≤ -65dBm ?
ANT2007, C2008

Yes

No Resolder or change
Check L2038 ≤ -65dBm ? C2024,C2268,C2133,L2022,F2004,C2007,
C2050,U2004,C2118,U2001,L2038

Yes

No
Check component soldering status OK at Resolder or change
U2006 U2006

Yes
No

Check component soldering status OK at Resolder or change


INP13000? INP13000

Yes
No

Check C15971,C15973,C15075,C15082 Resolder or change


≤ -65dBm ? C15971,C15973,C15075,C15082

Yes

NO
Resolder or change
Receiver is O.K?
U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-35. LTE B40 DRX

NORMAL CONDITION
Catch the channel?

No

No
Resolder or change
Check C2138≤ -65dBm ?
ANT2001,C223,C2020,C2021,C2230,C2138

Yes

No
Check L2213 ≤ -65dBm ? Resolder or change
F2008,C2116,L2213

Yes

No
Check component soldering status OK at Resolder or change
U2006 U2006

Yes
No

Check component soldering status OK at Resolder or change


INP13000? INP13000

Yes
No

Check C15971,C15973,C15075,C15082 Resolder or change


≤ -65dBm ? C15971,C15973,C15075,C15082

Yes

NO
Resolder or change
Receiver is O.K?
U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-36. CDMA BC1, LTE B1/2/3/4/25/34/39/66 TX

NORMAL CONDITION
Catch the channel?

No
Check C103 or C115 ≥ Check the ANT100,C103 or C115
23dBm

Yes
No
Resolder or change
Check C113≥ 23dBm Yes U110,C113
S

Resolder or change
Check C14009 ≥ 23dBm
C14019,C14009
No
Yes
S
Check C14004 ≥ 23dBm Resolder or change
F14000,C14004
No

Yes
S

No
Check component Resolder or change
soldering status ok? U14007
U14007

Yes
S

No
B1/2/25 Check L14043 ≥ 23dBm Resolder or change
B3/4/66 Check L14040 ≥ 23dBm B1/2/25 : C14006,C14007,U14001,C14043
B34/39 Check L14041 ≥ 23dBm B3/4/66 : C14021,C14026,U14004,L14040
B34/39 : L14041

Yes
S

No
Check component Resolder or change
soldering status ok? U14012
U14012

Yes

No
Check C14074 ≥0dBm Resolder or change
C14074,L14035

Yes
No
Check component
soldering status ok?
Resolder or change
U15000
U15000

Yes

END
Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-37. CDMA BC0/10, B5/8/12/13/14/18/19/20/26/28/71, NR_SUB6 n5/71 TX

NORMAL CONDITION
Catch the channel?

No
Check C103 or C115 ≥ Check the ANT100,C103 or C115
23dBm

Yes
No
Resolder or change
Check C113≥ 23dBm
U110,C113

Yes
S
Resolder or change
Check C14009 ≥ 23dBm
C14019,C14009

Yes No
S

Check L14006 ≥ 23dBm Resolder or change


F14000,L14006
No

Yes
S

No
Check component Resolder or change
soldering status ok? U14007
U14007

Yes
S

Resolder or change
B5/18/1926/BC0 Check L14058 or L14036 ≥ 23dBm B5/18/19/26/BC0:C14035,U14006,L14036,L14058
B8 Check L14023 ≥ 23dBm B8 : C14041,C14197,L14023
No B28 : C14014,C14196,L14027
B28 Check L14102 ≥ 23dBm
B12 Check L14048 ≥ 23dBm B12 : C14102,
B13 Check L14048 ≥ 23dBm B13 : L14048,L14049,
B14 Check L14068 ≥ 23dBm B14 :C14068,F14003,C14045,L14015,L14016
B20 Check L14033 ≥ 23dBm B20 :L14033
B71 Check L14094 ≥ 23dBm B71 : C14094,U14000,C14000

Yes
S

No
Check component Resolder or change
soldering status ok? U14012 or U14014
U14012 or U14014

Yes

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

No Resolder or change
Check C14067 or 14107
≥0dBm C14107,C14108,C14067,L14030

Yes

Check component No
soldering status ok? Resolder or change
U15000 U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-38. GSM 850/900 TX

NORMAL CONDITION
Catch the channel?

No
Check C103 or C115 ≥ Check the ANT100,C103 or C115
23dBm

Yes
No
Resolder or change
Check C113≥ 23dBm
U110,C113

Yes
S
No
Resolder or change
Check C14009 ≥ 23dBm
C14019,C14009

Yes
S
No
Check L14006 ≥ 23dBm Resolder or change
F14000,L14006

Yes
S

No
Check component Resolder or change
soldering status ok? U14007
U14007

Yes
S
No

Check L14089 ≥ 23dBm Resolder or change


L14089

Yes
S

Check component No
soldering status ok? Resolder or change
U14021 U14021

Yes
S No

Check L14088 ≥ 0dBm Resolder or change


L14088

Yes
S

Check component No
soldering status ok? Resolder or change
U15000 U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-39. LTE B7/38/40/41 TX

NORMAL CONDITION
Catch the channel?

No

No
Check C112 ≥ 23dBm Check the ANT101,C112

Yes
No
Resolder or change
Check C127 ≥ 23dBm
U120,L124,C120,C127,

Yes
No
Resolder or change
Check L14093 ≥ 23dBm
C14014,C14015,F14001,L14093

Yes
No
Resolder or change
Check CL14031 ≥ 23dBm
F14002,L14024,C14053,L14031

Yes

No
Check component
soldering status ok? Resolder or change
U14013 U14013

No
Resolder or change
Check C14086 ≥ 23dBm
C14086,L14042

Yes

Check component No
soldering status ok? Resolder or change
U15000 U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-40. LTE B30 TX

NORMAL CONDITION
Catch the channel?

No

No
Check C112 ≥ 23dBm Check the ANT101,C112

Yes
No
Resolder or change
Check C127 ≥ 23dBm
U120,L124,C120,C127,

Yes
No
Resolder or change
Check L14093 ≥ 23dBm
C14014,C14015,F14001,L14093

Yes
No
Resolder or change
Check CL14031 ≥ 23dBm
F14002,L14024,C14053,L14031

Yes

No
Check component
soldering status ok? Resolder or change
U14013 U14013

No
Resolder or change
Check C14100 ≥ 23dBm
C14100,F14005,C14088

No
Resolder or change
Check C14086 ≥ 23dBm
C14086,L14042

Yes

Check component No
soldering status ok? Resolder or change
U15000 U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-41. GSM DCS/PCS TX

NORMAL CONDITION
Catch the channel?

No
Check C103 or C115 ≥ Check the ANT100,C103 or C115
23dBm

Yes
No
Resolder or change
Check C113≥ 23dBm Yes U110,C113
S

No
Resolder or change
Check C14009 ≥ 23dBm
C14019,C14009

Yes
S
No
Check C14004 ≥ 23dBm Resolder or change
F14000,C14004

Yes
S

No
Check component Resolder or change
soldering status ok? U14007
U14007

Yes
S

No
Check L14086 ≥ 23dBm Resolder or change
L14086

Yes
S

No
Check component Resolder or change
soldering status ok?
U14021
U14021

Yes
S

No
Check L14085 ≥ 23dBm Resolder or change
L14085

Yes
S

Check component No
soldering status ok? Resolder or change
U15000 U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-42. N41 TX

NORMAL CONDITION
Catch the channel?

No

No
Check RFS2001 ≥ 23dBm Resolder or change
ANT2007, C2008

Yes
No Resolder or change
Check L2076 ≥ 23dBm L2201,L2054,F2002,C2205,C2204,C2267,C2
046,U2005,C2051,U2004,C2050,C2007,F200
4,L2022,C2268,C2133,C2024
Yes

Check component No
soldering status ok? Resolder or change
U2007 U2007

Yes

No
Resolder or change
Check L2203 ≥ 0dBm L2203,C2202

Yes

Check component No
soldering status OK at Resolder or change
INP13000? INP13000

Yes

Check component No
soldering status ok? Resolder or change
U15000 U15000

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-43. 5G mmW

NORMAL CONDITION
Catch the channel?

No
PASS
TRY 5G CAL

FAIL

FAIL
Change the FRC FPCB(GH59-15310A)
Check left module check Change the left 5G module(GH42-06625A)
Check the SOC14000

PASS

FAIL Change the V2 FPCB(GH59-15308A)


Check Right module check Change the left 5G module(GH42-06625A)
Check the SOC14002

PASS

Internal Device CAL V2, FAIL Resolder or change


XO CAL U12000

PASS

FAIL
Resolder or change
NR_FDRSB_CAL
U12001

PASS

YES
Replace the ASSY
Still CAL FAIL? SMD(Master+Interposer+Slave) to a new
one

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-44. Dex Station

Dex Station does not work

NO
Does the phone show the charging UI? Replace U7002 on the master PBA to a new one.

YES

NO
Does the phone show the DEX UI?
Replace U4004 on the master PBA to a new one.

YES

YES Replace USB1 on the CTC FPCB


Is USB1 on the CTC FPCB damaged? or

the CTC FPCB to a new one.

NO

Replace the ASSY SMD(Master+Interposer+Slave) to a new one

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.

You might also like