FY 50 WF

Square flanged ball bearing unit with eccentric locking,

cast iron housing, ISO
These square flanged ball bearing units are compliant with ISO standards. They
consist of an insert bearing, with an extended inner ring and eccentric locking,
and are intended primarily for use in applications where the direction of rotation
is constant. The bearing is mounted in a cast iron housing, which can be bolted to
a machine wall or frame. Ball bearing units can accommodate moderate initial
misalignment, but normally do not permit axial displacement.
• Resist high levels of contamination
• Designed for high temperatures and speeds
• Accommodate relatively heavy loads
• Cost-effective

Overview

Dimensions

Shaft diameter 50 mm

Housing overall width 43 mm

Width, total 66.1 mm

Centre distance between bolt holes 111 mm

Bearing width, total 62.7 mm

Performance Properties

Basic dynamic load 35.1 kN Housing type Flanged

rating
Flanged housing type Square
Basic static load rating 23.2 kN
Number of bolt holes for 4
Limiting speed 4 000 r/min fasteners

Note Limiting speed with shaft tolerance Fastening bolt hole type Plain
h6
Retaining feature, inner ring Eccentric collar

Bore type Cylindrical

Rubber seating ring Without

Material, housing Cast iron

Material, bearing Bearing steel

Coating Without

Sealing, bearing Seal and flinger on both

sides

Generated from www.skf.com on 2023-07-04 Page 1 of 6

 Sealing type Contact, standard

Sealing, unit Optional end cover

Lubricant Grease

Relubrication hole With

Grease fitting With

Generated from www.skf.com on 2023-07-04 Page 2 of 6

Technical Specification

Compliance with standard ISO

Purpose specific For material handling applications, For air handling applications

Material, housing Cast iron

Sealing, bearing Seal and flinger on both sides

Sealing type, bearing Contact, standard

Sealing, unit Optional end cover

Coating Without

Dimensions

d 50 mm Bore diameter
d1 ≈ 62.51 Outer diameter of inner ring
mm
d2 67.2 mm Outside diameter of locking ring

A 43 mm Overall width
A1 15 mm Flange width
A3 3.2 mm Depth of centring recess
A5 33 mm Standout of end cover
B1 62.7 mm Overall bearing width
B4 6.75 mm Distance from locking device side face to
thread centre
Db1 107 mm Top external diameter
Db2 118 mm Base external diameter
Dc 125.4 Diameter of housing centering recess
mm

J 111 mm Distance between attachment bolts

L 143 mm Overall length

N 18 mm Diameter of attachment bolt hole

s1 38.1 mm Distance from locking device side face to
raceway centre

T 66.1 mm Overall unit width

Generated from www.skf.com on 2023-07-04 Page 3 of 6

 Threaded hole

RG 1/4-28 UNF Housing thread for grease fitting

R1 28.5 mm Axial position of the housing thread

Grease fitting

DN 6.5 mm Diameter of head sphere of grease fitting

SWN7 mm Hexagonal key size for the grease fitting
GN 1/4-28 SAE-LT Thread of grease fitting

Dowel pins

J6 129 mm Distance of dowel pins

J7 35.5 mm Axial offset of dowel pins
N4 4 mm Recommended diameter for dowel pins

Calculation data

Basic dynamic load rating C 35.1 kN

Basic static load rating C0 23.2 kN

Fatigue load limit Pu 0.98 kN

Limiting speed 4 000 r/min

Limiting speed with shaft tolerance h6

Mass

Mass bearing unit 2.45 kg

Mounting information

Set screw G2 M10x1

Hexagonal key size for set screw 5 mm

Recommended tightening torque for set screw 16.5 N·m

Generated from www.skf.com on 2023-07-04 Page 4 of 6

 Recommended diameter for attachment bolts, mm G 16 mm

Recommended diameter for attachment bolts, inch G 0.625 in

Generated from www.skf.com on 2023-07-04 Page 5 of 6

Terms and conditions
By accessing and using this website / app owned and published by AB SKF (publ.) (556007-3495 ·
Gothenburg) (“SKF”), you agree to the following terms and conditions:

Warranty Disclaimer and Limitation of Liability

Although every care has been taken to assure the accuracy of the information on this website / app, SKF provides this
information "AS IS" and DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. You acknowledge that your
use of this website / app is at your sole risk, that you assume full responsibility for all costs associated with use of this
website / app, and that SKF shall not be liable for any direct, incidental, consequential, or indirect damages of any kind
arising out of your access to, or use of the information or software made available on this website / app. Any warranties
and representations in this website / app for SKF products or services that you purchase or use will be subject to the
agreed upon terms and conditions in the contract for such product or service. Further, for non-SKF websites / apps that
are referenced in our website / app or where a hyperlink appears, SKF makes no warranties concerning the accuracy or
reliability of the information in these websites / apps and assumes no responsibility for material created or published by
third parties contained therein. In addition, SKF does not warrant that this website / app or these other linked websites /
apps are free from viruses or other harmful elements.

Third Party Services

When viewing YouTube content via the SKF website(s) (i.e. using YouTube API Services), you agree to be bound by the
YouTube Terms of Service.

Copyright
Copyright in this website / app copyright of the information and software made available on this website / app rest with
SKF or its licensors. All rights are reserved. All licensed material will reference the licensor that has granted SKF the right
to use the material. The information and software made available on this website / app may not be reproduced,
duplicated, copied, transferred, distributed, stored, modified, downloaded or otherwise exploited for any commercial use
without the prior written approval of SKF. However, it may be reproduced, stored and downloaded for use by individuals
without prior written approval of SKF. Under no circumstances may this information or software be supplied to third
parties.
This website /app includes certain images used under license from Shutterstock, Inc.

Trademarks and Patents

All trademarks, brand names, and corporate logos displayed on the website / app are the property of SKF or its licensors,
and may not be used in any way without prior written approval by SKF. All licensed trademarks published on this website
/ app reference the licensor that has granted SKF the right to use the trademark. Access to this website / app does not
grant to the user any license under any patents owned by or licensed to SKF.

Changes
SKF reserves the right to make changes or additions to this website / app at any time.

Generated from www.skf.com on 2023-07-04 Page 6 of 6