Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 13 views

    Day 3

    Uploaded by

    TATA STEEL
    The document introduces several modifying commands in AutoCAD like Trim, Extend, and Offset that are commonly used for 2D drawings, provides instructions for an assignment using lines, rectangles, circles, and these modifying commands to draw a simple shape, and explains how to use object snaps to precisely place geometry like snapping to the center of a circle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Day 3

    Uploaded by

    TATA STEEL
    13 views6 pages
    The document introduces several modifying commands in AutoCAD like Trim, Extend, and Offset that are commonly used for 2D drawings, provides instructions for an assignment using lines, rectangles, circles, and these modifying commands to draw a simple shape, and explains how to use object snaps to precisely place geometry like snapping to the center of a circle.

    Original Description:

    qerwerwqere

    Original Title

    Day-3

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document introduces several modifying commands in AutoCAD like Trim, Extend, and Offset that are commonly used for 2D drawings, provides instructions for an assignment using lines, rectangles, circles, and these modifying commands to draw a simple shape, and explains how to use object snaps to precisely place geometry like snapping to the center of a circle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    13 views6 pages

    Day 3

    Uploaded by

    TATA STEEL
    The document introduces several modifying commands in AutoCAD like Trim, Extend, and Offset that are commonly used for 2D drawings, provides instructions for an assignment using lines, rectangles, circles, and these modifying commands to draw a simple shape, and explains how to use object snaps to precisely place geometry like snapping to the center of a circle.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    Rectangle | Extend | Offset | Trim | Introduction to Object Snaps

    The previous lesson dealt with drawing commands. This lesson will introduce some common
    modifying commands. In AutoCAD, you may actually use modifying commands more often than
    drawing commands. Now that you know the basics, here's some more commands to add to your
    collection. Three commands, Trim, Extend and Offset are used often in 2D AutoCAD work.

    Command Keystroke Icon Location Result


    RECTANGLE / Home > Draw > Draws a rectangle after you enter
    Rectangle
    REC Rectangle one corner and then the second.
    Home > Modify rims objects to a selected cutting
    Trim TRIM / TR
    > Trim edge.
    Home > Modify Extends objects to a selected
    Extend EXTEND / EX
    > Extend boundary edge.
    Home > Modify Offsets an object (parallel) by a set
    Offset OFFSET / O
    > Offset distance.
    OSNAP / OS / Tools > Object
    Object Snaps Brings up the OSNAP dialog box.
    F3 Snap Settings

    Assignment #2 - Modifying Commands

    The purpose of this assignment is to use the commands learned in the previous lesson and
    learn some new ones.

    Once again, do not worry about title blocks, text or dimensions, draw only the geometry (in
    green)
    Start AutoCAD and begin the the drawing by opening up the template file like you did in
    Lesson 1-2. Draw a LINE from 1,2 to 3,2 to 3,4 to 1,4 (*Remember to watch the command
    line as you do this.) For the last line's endpoint , you can either type in 1,2 or C to close the
    line back to the first point you entered. These are absolute coordinates. Make sure you
    understand what the points your just entered represent.

    Draw the next square using the RECTANGLE command. A rectangle is created by
    specifying 2 points to represent the opposite corners. Enter the first point as 4.5,2 and then
    make the opposite corner 2 inches over and 2 inches up @2,2 using relative coordinates.
    This is much faster and also makes the square one object and not 4 separate lines.

    ERASE the rectangle. You will see that all of it is gone with one pick. Redraw it and
    continue.

    For the 3rd square, draw a 1.5 x 1.5 unit square using any of the methods you know. The
    bottom left corner must be at 8,2.
    Draw a line from 2,5 to 2,6.5 Draw another line from 1,6 to 3,6 You should now have two
    perpendicular lines. What you want to do is trim off the top of the vertical line and create a T.
    Start the TRIM command. It will first ask for a cutting edge. Select the horizontal line and
    press <ENTER>. It will now ask for the object to be trimmed. Select the vertical line
    anywhere above the horizontal (cutting) line and press <ENTER> to finish the command.
    This is what you saw on the command line:

    Command: TR TRIM
    Current settings: Projection=UCS, Edge=None
    Select cutting edges ...
    Select objects: <Select the Horizontal line> 1 found
    Select objects: <enter>
    Select object to trim or shift-select to extend or [Fence/Crossing/Project/Edge/eRase/Undo]:
    <Select the vertical line>
    Select object to trim or shift-select to extend or [Project/Edge/Undo]: <enter>

    Once again, it is important to keep your eye on the command line as it will guide you through
    most commands. Draw a LINE from 4,6.5 to 6,6.5 Draw another line from 5,5 to 5,6 What
    you want to do now is extend the vertical line up to the meet horizontal line. Start the
    EXTEND command. AutoCAD asks for a boundary edge; select the horizontal line press
    <ENTER>. It then asks for an object to extend; select somewhere in the top half of the
    vertical line. Press <ENTER> to end the command. Your command line history should match
    what is shown below.

    Command: EX <enter> EXTEND


    Current settings: Projection=UCS, Edge=None
    Select boundary edges ...
    Select objects: <Select the horizontal line> 1 found
    Select objects: <enter>
    Select object to extend or shift-select to trim or [Fence/Crossing/Project/Edge/Undo]: <Select
    the top half of the vertical line>
    Select object to extend or shift-select to trim or [Project/Edge/Undo]: <enter>
    Draw a CIRCLE with a center point of 7.5,5.5 with a radius of .5 Now you will use to offset
    command to make another circle 1/4" larger. Start the OFFSET command (watch the
    command line) and enter .125 as the offset distance (1/2 of 1/4"). Now select the circle and
    pick anywhere outside the circle. Press <ENTER> to end the command.

    BREAK TIME: You won't believe me now, but I use the Offset A LOT when I am drafting.
    As you watch the videos in the next level, you'll see what I mean. I would be lost without my
    Offset. You will be too, so learn how to use it and be quick with it. You'll get more practice.

    Object Snaps

    Suppose you want to draw a line from the center of the circle to the middle of the vertical line
    you extended earlier. AutoCAD has a feature that makes this very easy. These are the Object
    Snaps (or Osnaps "Oh-Snaps"). Type OS <ENTER> . You will see this dialog box appear.

    Icon Setting Icon Setting


    Endpoint Insertion Point
    Midpoint Perpendicular
    Center Tangent
    Icon Setting Icon Setting
    Node Nearest
    Apparent
    Quadrant
    Intersection
    Intersection Parallel
    Mindpoint between
    Extension M2P
    2 points

    You may select whichever points you want to 'snap' on an object. Here is a list of your options.
    Followed by the command entry to invoke the needed Osnap.

    Endpoint - snaps to either the beginning or the end of an object such as a line - END
    Midpoint - snaps to the exact middle of a line or an arc - MID
    Center - snaps to the center-point of a circle or arc - CEN
    Node - snaps to 'nodes' (not covered in this course) - NOD
    Quadrant - snaps to any of the four quadrants of a circle - QUA
    Intersection - snaps to the point where two object cross - INT
    Extension - Snaps to the phantom extension of an arc or line - EXT
    Insertion - snaps to the insertion point of an object (such as a block or text) - INS
    Perpendicular - will snap so that the result is perpendicular to line selected - PER
    Tangent - snaps to create a line tangent to a circle or arc - TAN
    Nearest - will find the closest point an object and snap to that point - NEA
    Parallel -Snaps parallel to a specified line - PAR
    M2P - This isn't technically an 'Object Snap' as you are not snapping to specific point on an object,
    but it allows you to select 2 points and it will calculate the midpoint between those 2 points. This is a
    very handy option to have.

    Note: Beside each checkbox is a symbol. That symbol will show up on the screen when you have
    found a valid snap point. (An endpoint will show a small square). If you select the "Options" button,
    you can change the aperture size and the color of the Osnaps. Depending upon the background you
    are drawing on, this may be needed. Osnaps are explained in more depth in tutorial 4-2, but this will
    be enough for you now.

    TIP: Before you select the Osnap you want, you can press the TAB key on your keyboard to
    cycle through the available Osnaps in the area of your cursor.
    CAUTION: Although it may seem tempting to turn 'all' the Osnaps on when drawing, you
    can have too much of a good thing. For example, in shorter lines, Midpoint, Nearest and
    Perpendicular could all be very close to each other, and you could select the wrong point.
    When you have finished the assignment, continue practicing with these commands until they
    are mastered. These are common commands that you will use in everyday drafting.

    Extra Practice: Copy this drawing, using lines, offset, osnaps - click to view extra_003.gif
    Extra Practice: Copy this drawing, it could a little to figure out, but still uses the commands
    you have learned so far. - click to view extra_004.gif
    Question 1 of 5

    When using the TRIM command, which do you select first?

    • The cutting edges


    • The object to be trimmed
    • Everything

    Question 2 of 5

    How many snap points does an object have?

    • Depends upon the object


    • 3 or more
    • 1

    Question 3 of 5

    Polar coordinates are used mostly for drawing...?

    • Vertical LInes
    • Curved Lines
    • Angled Lines

    Question 4 of 5

    How many points do you need to define for the rectangle command?

    • 1
    • 4
    • 2

    Question 5 of 5

    How many AutoCAD objects are in a rectangle?

    • 1
    • 4
    • 2

    You might also like