Ata25 Airbus

A330
TECHNICAL TRAINING MANUAL
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3)
(RR Trent 700)
EQUIPMENT/FURNISHINGS
This document must be used for training purposes only
Under no circumstances should this document be used as a reference
It will not be updated.
All rights reserved

No part of this manual may be reproduced in any form,
by photostat, microfilm, retrieval system, or any other means,
without the prior written permission of AIRBUS S.A.S.
AIRBUS Environmental Recommendation

Please consider your environmental responsability before printing this document.
A330 TECHNICAL TRAINING MANUAL
EQUIPMENT/FURNISHINGS
Equipment/Furnishings Line MAINT Briefing . . . . . . . . . . . . . . . . . . 2
COCKPIT
Cockpit D/O (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
PASSENGER COMPARTMENT
Passenger Compartment D/O (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CREW REST COMPARTMENT
Crew Rest Compartment D/O (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
GALLEY COOLING
Galley Trolley Compartment Cooling System D/O (3) . . . . . . . . . . 114
EMERGENCY EQUIPMENT
Emergency Equipment Cockpit D/O (3) . . . . . . . . . . . . . . . . . . . . . 120
Emergency Equipment Cabin D/O . . . . . . . . . . . . . . . . . . . . . . . . . . 126
LOWER DECK AREA
Lower Deck Decompression Safety System . . . . . . . . . . . . . . . . . . 146
CARGO LOADING
Lower Deck Cargo Loading System D/O (3) . . . . . . . . . . . . . . . . . . 152
MAINTENANCE PRACTICE
Equipment/Furnishings System Base Maintenance (3) . . . . . . . . . . 166
Linings & Furnishings Removal/Installation (3) . . . . . . . . . . . . . . . 202
G9409341 - GAUT0T0
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent TABLE OF CONTENTS Sep 02, 2009
700) Page 1
25 - EQUIPMENT/FURNISHINGS
EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

SYSTEM OVERVIEW
The equipment and furnishings chapter covers:
- the cockpit,
- the passenger compartment,
- the crew rest compartment,
- the emergency equipment,
- the cargo compartments,
- the miscellaneous compartments.
When you work on aircraft, you must obey all the safety procedures listed
in the Aircraft Maintenance Manual (AMM).
G9409341 - GAUT0T0 - FM25B1000000001
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING Aug 31, 2009
700) Page 2
G9409341 - GAUT0T0 - FM25B1000000001
SYSTEM OVERVIEW
700) Page 3

SYSTEM OVERVIEW (continued)
CABIN PANEL LAYOUT
The cabin interior has removable panels. The lining design allows
cabin customization. The lower sidewall (Dado) panels are mounted
between the cabin floor and the sidewall panels. They have rapid
decompression panels, which operate during decompression either in
the cabin or in the cargo compartment. The sidewall panels are
mounted on the side of the cabin. They include the window contour.
Inner window panels and sun visors are installed on to the window
frame. The closing cover panels cover the space between the ceiling
panels and the cover light panels.
The cover light panels cover the space between the sidewall panels
and the overhead stowage compartments. The overhead bins or cover
plates are removable. Removable ceiling panels are mounted in the
cabin. They are installed over the full length of the cabin and the utility
areas. The cover plates are installed where there is no overhead
stowage compartment installed along the top.
G9409341 - GAUT0T0 - FM25B1000000001
700) Page 4
G9409341 - GAUT0T0 - FM25B1000000001
SYSTEM OVERVIEW - CABIN PANEL LAYOUT
700) Page 5

CABIN ESCAPE FACILITIES
The type "A" passenger doors can have escape slides or slide rafts.
The type "1" emergency exits have escape slides. They are used for
quick evacuation in case of emergency. Deployment of the slide/rafts
is automatic when the door is opened with the evacuation system in
the armed mode.
If the automatic slide inflation system fails, the slide/raft can be
manually inflated.
G9409341 - GAUT0T0 - FM25B1000000001
700) Page 6
G9409341 - GAUT0T0 - FM25B1000000001
SYSTEM OVERVIEW - CABIN ESCAPE FACILITIES
700) Page 7
G9409341 - GAUT0T0 - FM25B1000000001
SYSTEM OVERVIEW - CABIN ESCAPE FACILITIES
700) Page 8
This Page Intentionally Left Blank

G9409341 - GAUT0T0 - FM25B1000000001
700) Page 9

LOWER DECK CARGO COMPARTMENTS
The aircraft has three lower deck cargo compartments in the lower
part of the fuselage. They are:
- the forward cargo compartment,
- the aft cargo compartment,
- the bulk cargo compartment.
The forward and aft cargo compartments have an independently
operated semi-automatic Cargo Loading System (CLS) and can
accommodate cargo in containers or on pallets. The bulk cargo
compartment is designed for transportation of bulk cargo, passenger
luggage and alive animals. Access to the forward, aft and bulk cargo
compartments is gained through doors located on the right hand side
of the fuselage. Two hydraulically operated outwards opening doors
give access to the forward and aft cargo compartments. The bulk cargo
has one manually operated door, which opens inwards.
The inside of the cargo compartments is composed of:
- floor panels,
- ceiling panels,
- side linings,
- partition walls.
G9409341 - GAUT0T0 - FM25B1000000001
All the linings and panels are sealed to give a fully sealed
compartment. Rapid decompression panels, blow in, blow out panels
are installed in the linings to prevent damage from differential pressure
during climb and descent. In case of decompression in the cabin or
in the cargo compartment, they equalize the pressure in both sections,
to avoid damage to the structure.
700) Page 10
G9409341 - GAUT0T0 - FM25B1000000001
SYSTEM OVERVIEW - LOWER DECK CARGO COMPARTMENTS
700) Page 11
G9409341 - GAUT0T0 - FM25B1000000001
SYSTEM OVERVIEW - LOWER DECK CARGO COMPARTMENTS
700) Page 12

G9409341 - GAUT0T0 - FM25B1000000001
700) Page 13

LOWER DECK CARGO LOADING SYSTEM (CLS)
The semi-automatic CLS of the forward and aft cargo compartments
is used to load, unload and move the ULDs. These ULDs can be pallets
or containers of different sizes. One person can operate the CLS. If
there is no electrical power available, it is possible to manually load
or unload. The semi-automatic cargo loading systems of the forward
and the aft lower deck cargo compartments are similar in construction
and work independently
The CLS includes:
- control panel installed adjacent to the cargo compartment door,
- control box,
- Power Drive Units (PDUs),
- proximity switches located on the different latches.
For the powered loading operation, the power switch must be in the
ON position. The AC/DC power is available and the manual doorsill
latch must be in the lowered position. The control panel sends
electrical signals through the control box to the applicable PDUs. The
PDUs move the ULDs in the necessary direction and to their loading
positions. When a ULD is in the correct loading position, you must
lock the latch manually.
G9409341 - GAUT0T0 - FM25B1000000001
700) Page 14
G9409341 - GAUT0T0 - FM25B1000000001
SYSTEM OVERVIEW - LOWER DECK CARGO LOADING SYSTEM (CLS)
700) Page 15

MEL/DEACTIVATION
One or more escape slide/slide raft cabin passenger exit door may be
inoperative if the related door is inoperative (cannot be used in case of
emergency evacuation). One or more slide bottle pressure indication on
the Forward/Flight Attendant Panel (FAP) may be inoperative if the
related slide bottle pressure is checked before the first flight of each day.
NOTE: The number of inoperative doors on the aircraft changes

according to the local regulations (limit the number of
passengers).
One or more blow in/out panels in cargo compartments may be damaged
or missing if related cargo compartment is empty or does not contain
inflammable or combustible materials. One or more lining panels in cargo
compartments may be damaged if related cargo compartment is empty
or does not contain inflammable or combustible materials. One or more
lining panels in cargo compartments may be missing if related cargo
compartment is empty.
In case of malfunction or failure of the lower deck CLS, refer to the ramp
dispatcher which will decide if loading restrictions must be applied in
accordance with the Weight and Balance Manual (WBM).
NOTE: : SOME AIRLINES PUT THE WBM LIMITS AND

G9409341 - GAUT0T0 - FM25B1000000001
RESTRICTIONS IN THE MEL CHAPTER 25
CAUTION: In the case of malfunction of any part of the cargo loading

system, restrictions may be imposed on pallet/container
gross weights or their position in the cargo hold.
700) Page 16
G9409341 - GAUT0T0 - FM25B1000000001
MEL/DEACTIVATION
700) Page 17
G9409341 - GAUT0T0 - FM25B1000000001
MEL/DEACTIVATION
700) Page 18
G9409341 - GAUT0T0 - FM25B1000000001
MEL/DEACTIVATION
700) Page 19
G9409341 - GAUT0T0 - FM25B1000000001
MEL/DEACTIVATION
700) Page 20

G9409341 - GAUT0T0 - FM25B1000000001
700) Page 21

MAINTENANCE TIPS
SAFETY THE DOOR CYLINDER PERCUSSION
MECHANISM
A Type A door has been chosen as an example. Make sure that the
emergency control handle is locked in the disarmed position and
secured with the safety pin.
If maintenance has to be done at or near the door, the striker lever
must be set to the maintenance position, to prevent operation of the
door emergency cylinder. The door is now in maintenance
configuration.
G9409341 - GAUT0T0 - FM25B1000000001
700) Page 22
G9409341 - GAUT0T0 - FM25B1000000001
MAINTENANCE TIPS - SAFETY THE DOOR CYLINDER PERCUSSION MECHANISM
700) Page 23
G9409341 - GAUT0T0 - FM25B1000000001
MAINTENANCE TIPS - SAFETY THE DOOR CYLINDER PERCUSSION MECHANISM
700) Page 24

G9409341 - GAUT0T0 - FM25B1000000001
700) Page 25

MAINTENANCE TIPS (continued)
DISARM THE DOOR ESCAPE SLIDE RESERVOIR
The passenger/crew door escape slide reservoir is located behind a
cover. To fulfill the maintenance tasks on the door, the attached
slide/raft activating system must be disarmed. The door arming
mechanism must be set to the disarmed position and secured with the
safety pin. After removing the cover, secure the inflation reservoir
using the safety pin from the stowage pocket located inside the cover.
The pin-fitting procedure is slightly different for Type A and Type 1
doors. The door escape slide is now in maintenance configuration.
G9409341 - GAUT0T0 - FM25B1000000001
700) Page 26
G9409341 - GAUT0T0 - FM25B1000000001
MAINTENANCE TIPS - DISARM THE DOOR ESCAPE SLIDE RESERVOIR
700) Page 27

'A' CHECK ITEMS
VISUAL INSPECTION TO CHECK THE INTEGRITY
OF THE CARGO COMPARTMENT
Moreover, in relation with the Maintenance Planning Document
(MPD), the visual inspection of cargo compartment decompression
and lining panels must be done every 600 Flight Hours (FH).
Look carefully at each decompression panel for cracks and other
damage.
NOTE: If a decompression panel is damaged, do a repair or replace

the panel.
Make sure that each decompression panel has a seal installed: missing
seals are not permitted, and make sure that seals are in the correct
condition. Make sure that each decompression panel is in the correct
position.
Look carefully at each lining panel for cracks and other damage, as
well as their correct attaching.
NOTE: If a lining panel is damaged, do a repair or replace the panel.

G9409341 - GAUT0T0 - FM25B1000000001
700) Page 28
G9409341 - GAUT0T0 - FM25B1000000001
'A' CHECK ITEMS - VISUAL INSPECTION TO CHECK THE INTEGRITY OF THE CARGO COMPARTMENT
700) Page 29
COCKPIT D/O (3)

back to a vertical position. A free wheel serves to avoid interference
PILOT SEATS between the armrest and the lateral console.
The seating assy consists of a seatpan and a cushion. The seatpan is
The description, operation and attachment are the same for the captain
a metallic structure, attached to the moving part of the telescopic
and the first officer seat as they are symmetrical. However, they are not
column. Footrests are provided on the aft part of the seatpan. The
interchangeable because of the armrests and the controls.
cushion provides good support and ensures good pressure distribution.
DESCRIPTION A life vest is stowed on the aft side of the backrest in a compartment
Each pilot seat consists of: accessible through a hinged door and held closed by means of two
- a backrest, magnets.
- two armrests, The telescopic column is made up of three sections:
- a seating assy, - the seatbase, connecting the seat to the cockpit floor,
- a telescopic column, - the moving section, supporting the seatpan,
- a shoulder harness with a control lever, - the free section which slides into the moving section and the base.
- a life vest compartment.
The safety harness is a five-strap model equipped with a buckle. The
straps can be clicked into the buckle in any order. To release the straps,
the buckle has to be turned a quarter turn. Pushing on top releases the
shoulder harness alone. The shoulder harness is fitted on an inertial
reel, which can be locked by a control lever, located behind the
backrest.
The backrest is designed to offer maximum comfort to the occupant
and to provide good lateral support of the body. The backrest is divided
G9409341 - GAUT0T0 - FM25D1F25AE0102
into two parts:

- the backrest,
- the lumbar rest.
The two parts are integral.
The inboard armrest is located on the pedestal side. The armrest is
hinged to the backrest and can be raised vertically and stowed behind
the backrest.
A sidestick armrest is located on the console side and contains the
fixed arm, the carrier arm and the table. It is attached to the seatpan
and is independent from the backrest movements. It can be folded
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent COCKPIT D/O (3) Aug 31, 2009
700) Page 30
G9409341 - GAUT0T0 - FM25D1F25AE0102
PILOT SEATS - DESCRIPTION
700) Page 31
COCKPIT D/O (3)

- put the seat into position and install the washers and screws and
PILOT SEATS (continued) tighten them. Paint the bolts with structure paint,
- reinstall the armrest,
OPERATION
- in the avionics compartment, remove the blanking caps from the
Pilot seats have electrical controls for horizontal and vertical travel. connectors and connect the electrical connectors,
Mechanical controls may be used to override the electrical controls - clean the working area and de-energize the ground service network.
in case of electrical component failure. Other mechanical controls are
used for further adjustment of the seat.
Electrical control is provided by a gear motor. With vertical travel,
the free section is pulled off or pushed into the seat base. Horizontal
travel is determined by a roller fitted under the seatpan, which slides
into the L-shaped track.
The control levers "V", "H" and "R" are used for mechanical vertical,
horizontal or backrest movements respectively. When a lever is
pushed, the system is unlocked. As soon as the lever is released, the
system is locked. A gas cylinder is used to slow down vertical and
backrest movements.
Rotation of the knobs ensures depth adjustment and vertical movement
of the lumbar rest.
The button located on the armrest ensures angular adjustment by
means of a screw-nut system and associated stop. Continuous
adjustment is possible in a range of 15 degrees downwards and 10
degrees upwards.
G9409341 - GAUT0T0 - FM25D1F25AE0102
A sidestick armrest is located on the console side. The table tilt and
the carrier arm height can be adjusted.
ATTACHMENT
The pilot seats are attached to the cockpit floor by means of eight hex
head screws.
The steps of the procedure are explained as follows:
- energize the ground service network,
- get access to the avionics compartment through door 811 and then
open, safety and tag, the corresponding circuit breakers,
- remove the sidestick armrest from the seat to get it into the cockpit,
700) Page 32
G9409341 - GAUT0T0 - FM25D1F25AE0102
PILOT SEATS - OPERATION & ATTACHMENT
700) Page 33
COCKPIT D/O (3)

THIRD OCCUPANT SEAT
The basic structure and shape of the third occupant seat is identical to
the pilot seats. Thus the description remains valid.
The differences between the third occupant seat and the pilot seat are as
follows:
- the third occupant seat has only mechanical controls so no circuit
breakers and no electrical connector to deal with during removal and
installation,
- it is raised by 100 mm (3.94 inches) on the rotating star for good
visibility.
When aligned with the centerline and in extreme forward position, the
seat rotates counter-clockwise to one of three positions: 30, 45 or 68
degrees. The lateral travel is 101.6 mm (4 inches) instead of 76.2 mm (3
inches) for the pilot seat.
Both armrests are of the pilot inboard armrest type. The life vest is stowed
in a box located on the aft partition of the cockpit.
G9409341 - GAUT0T0 - FM25D1F25AE0102
700) Page 34
G9409341 - GAUT0T0 - FM25D1F25AE0102
THIRD OCCUPANT SEAT
700) Page 35
COCKPIT D/O (3)

- put the life vest in its compartment and close the door,
FOURTH OCCUPANT SEAT - make sure that the work area is clean and de-energize the ground
service network.
Now, we shall see different aspects of the fourth occupant seat which is
a folding seat.
DESCRIPTION
The fourth occupant seat consists of:
- a headrest,
- a backrest,
- a seating panel,
- a shoulder harness with a control lever,
- a life vest stowage.
The shoulder harness control lever is located on the right hand side
of the seat. It is possible to immobilize the occupant if he/she is taken
ill (or for other reasons). This is therefore an emergency procedure.
The seating panel rotates down in use. It automatically returns to the
stowed position aligned with the backrest when not in use.
A stowage compartment is located below the seating panel. It is closed
by means of a lock and contains a life vest.
The headrest is integral with the backrest.
The safety harness is a five-strap model equipped with a buckle. The
abdominal belt has NO sleeve to enable stowage.
G9409341 - GAUT0T0 - FM25D1F25AE0102
OPERATION
The fourth occupant seat is NOT adjustable.
ATTACHMENT
The fourth occupant seat is attached to the floor by means of four hex
head screws. It forms an angle of 28 degrees with respect to the aft
partition. It is inclined backwards by 4.42 degrees.
The steps of the procedure are explained as follows:
- the ground service network has to be energized,
- put the seat in position, install the washers and screws (in the life
vest compartment) and tighten them,
700) Page 36
G9409341 - GAUT0T0 - FM25D1F25AE0102
FOURTH OCCUPANT SEAT - DESCRIPTION ... ATTACHMENT
700) Page 37
PASSENGER COMPARTMENT D/O (3)

GENERAL
The passenger compartment can be laid out according to the airline
request. The cabin configuration determines the amount and the position
of various items like:
- seats,
- lavatories,
- galleys,
- curtains and partitions.
The other linings and furnishings do not depend on the configuration
chosen by the airline.
G9409341 - GAUT0T0 - FM25D2000000002
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent PASSENGER COMPARTMENT D/O (3) Aug 31, 2009
700) Page 38
G9409341 - GAUT0T0 - FM25D2000000002
GENERAL
700) Page 39

LINING AND FURNISHING PANELS
The cabin linings follow the inner contour of the fuselage. They are
installed to cover up the fuselage structure, thermal and acoustical
insulation and components of the electrical and air conditioning systems.
Different panels make up the cabin linings:
- the ceiling panels in the cabin are installed over the full length of the
cabin and the utility areas. The ceiling is made up of different panels; the
closing covers installed along the lateral overhead stowage compartments
top, ceiling panels and cover plates if there is no overhead stowage
compartment installed along the top,
- the ceiling panels in the forward and aft utility areas are flat panels.
Each exit-ceiling panel is made of a base and a decor panel,
- the sidewall panels are installed along the sidewalls. The panels are
moulded plastic window frames,
- the dado panels are installed along the lower sidewalls. All dado panels,
except those installed above the cargo compartment doors, have a rapid
decompression safety system,
- the door linings are installed on each passenger/crew door and
emergency exit door,
- the lateral light covers are installed below the RH and LH overhead
stowage compartments.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 40
G9409341 - GAUT0T0 - FM25D2000000002
LINING AND FURNISHING PANELS
700) Page 41

LINING AND FURNISHING PANELS (continued)
DECOMPRESSION
The rapid decompression safety system prevents a pressure difference
between the cabin and the cargo compartments when rapid
decompression occurs. This system avoids a subsidence of the
passenger compartment floor if rapid decompression occurs in flight.
This system is made of:
- rapid decompression panels in the cargo compartments,
- dado panels in the cabin,
- air grills in the stowage and lavatories.
the rapid decompression panels and the dado panels let the air flow
between the cargo compartments and the cabin. The air grills let the
air move freely to and from the housings.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 42
G9409341 - GAUT0T0 - FM25D2000000002
LINING AND FURNISHING PANELS - DECOMPRESSION
700) Page 43

INSULATION
The thermal and acoustical insulation insulates the pressurized area
of the fuselage against the outside temperature and noise. It is
composed of insulation blankets and insulation foam bonded with the
panel. The thermal and acoustic insulation is present in the following
areas:
- between the frames,
- over the frames,
- over the structure brackets,
- on the cargo-compartment floor panels,
- on the pressure bulkheads.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 44
G9409341 - GAUT0T0 - FM25D2000000002
LINING AND FURNISHING PANELS - INSULATION
700) Page 45

HEATED FLOOR PANEL SYSTEM (HFPS)
Heated Floor Panels (HFPs) are installed to increase the temperature
of the cabin area in the following areas:
- in the area of the passenger/crew doors (from door 1 thru 4),
- in the area of the emergency exits,
- in the aft galley area.
Two Ice Protection Control Units (IPCUs) control and monitor the
HFPs and are installed in the underfloor compartments:
- the IPCU located in the avionics compartment controls the forward
area,
- the IPCU located in the aft cargo compartment controls the aft area.
The Floor Temperature Setting Panels (FTSPs) are installed to indicate
and to adjust the HFPs status but also to test the HFPS with a BITE
function. FTSPs are located:
- in the RH area of the passenger/crew doors,
- and at the rear wall of the aft galley area.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 46
G9409341 - GAUT0T0 - FM25D2000000002
LINING AND FURNISHING PANELS - HEATED FLOOR PANEL SYSTEM (HFPS)
700) Page 47
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 48
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 49

LINING AND FURNISHING LAYOUT
The floor covering is installed in the cabin and in the utility areas. The
floor of the passenger area is covered with textile materials. The floor of
each cabin utility area is covered with non-textile materials.
This protects the floor structure from liquids that can cause corrosion.
Textile flooring is installed with double-sided adhesive tape around the
outer edges of each piece except for the aisle where it is fully bonded.
Stainless-steel cover-strips are installed across the aisles to cover the
joints between the textile and the non-textile floor coverings. The seat
tracks below the non-textile floor covering are treated with a corrosion
inhibitor spray. Adhesive foil attaches the non-textile floor covering to
the floor panels.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 50
G9409341 - GAUT0T0 - FM25D2000000002
LINING AND FURNISHING LAYOUT
700) Page 51

LINING AND FURNISHING LAYOUT (continued)
SEPARATION AND OVERHEAD STOWAGE
The curtains and partitions are used for separation between the utility
and the seating areas. The OverHead Stowage Compartments (OHSCs)
are installed for stowage passenger luggage and miscellaneous
equipment. There are three kinds of compartment:
- the lateral OHSCs,
- the center OHSCs,
- the center retractable OHSCs.
The stowage is also used for ancillary items and emergency equipment.
Some of the stowage has electrical equipment installed.
The lateral OHSCs are single-box structures and each stowage has
one or two doors with a locking mechanism. The center OHSCs are
double-box structures and each stowage has two or four doors with a
locking mechanism. The center retractable OHSCs are double-box
structures. Each stowage compartment has an access door and a bin.
Each bin has two rollers, which are located in the guide rails on the
stowage compartment and a locking mechanism.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 52
G9409341 - GAUT0T0 - FM25D2000000002
LINING AND FURNISHING LAYOUT - SEPARATION AND OVERHEAD STOWAGE
700) Page 53

PASSENGER SERVICE CHANNEL
The Passenger Service/Information Units (PSIUs) are installed in the
passenger service channels adjacent to the emergency oxygen containers.
The passenger service channels are found at the bottom of the OHSCs
above each seat row. If the center OHSCs are not installed, the PSIUs
are installed in the cabin ceiling.
Each PSIU has two primary units:
- the Passenger Service Unit (PSU),
- the Passenger Information Unit (PIU).
The PSUs are installed above each seat row, the PIUs above each second
seat row. The PSIU could be divided into various parts:
- a reading light panel,
- a fresh air outlet panel,
- a loudspeaker,
- a "FASTEN SEAT BELT" lighted sign,
- a "NO SMOKING" lighted sign.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 54
G9409341 - GAUT0T0 - FM25D2000000002
PASSENGER SERVICE CHANNEL
700) Page 55

PASSENGER SERVICE CHANNEL (continued)
PSIU INTERFACES
The PSIU has interfaces with the following systems:
- air conditioning system,
- communication system,
- lighting system,
- oxygen system.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 56
G9409341 - GAUT0T0 - FM25D2000000002
PASSENGER SERVICE CHANNEL - PSIU INTERFACES
700) Page 57

PASSENGER COMPARTMENT SEAT
The passenger compartment can be laid out according to the airline
request. The cabin configuration determines the type, the amount and the
position of passenger seats.
The three typical configurations are:
- one first class, one business class and one tourist class,
- one business class and one tourist class,
- only one tourist class.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 58
G9409341 - GAUT0T0 - FM25D2000000002
PASSENGER COMPARTMENT SEAT
700) Page 59

PASSENGER COMPARTMENT SEAT (continued)
PASSENGER SEAT DESCRIPTION
In each class, there are several types of passenger seat assemblies:
- single seat,
- double seat,
- triple seat,
- quadruple seat.
In the seat, there are the following components:
- seat electronic box,
- life vest container,
- baggage bar,
- framework,
- seat cushion,
- seat belt,
- folding armrest,
- backrest upholstery,
- folding table,
- Passenger Control Unit (PCU),
- fixed armrest.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 60
G9409341 - GAUT0T0 - FM25D2000000002
PASSENGER COMPARTMENT SEAT - PASSENGER SEAT DESCRIPTION
700) Page 61

PASSENGER COMPARTMENT SEAT (continued)
PASSENGER SEAT ATTACHMENT DESCRIPTION
The passenger seats are installed on the seat tracks of the cabin floor
structure. Quick release fittings at the front and the rear legs hold the
seats in position.
During a passenger seat installation, make sure that the front stud is
correctly installed in the front leg before you install the seat assembly
on the seat track.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 62
G9409341 - GAUT0T0 - FM25D2000000002
PASSENGER COMPARTMENT SEAT - PASSENGER SEAT ATTACHMENT DESCRIPTION
700) Page 63

CABIN ATTENDANT SEAT
The cabin configuration determines the amount and the position of cabin
attendant seats. Cabin-attendant seats have:
- a stowage compartment,
- a folding seat pan,
- a backrest with cushion,
- a seat belt and shoulder harness,
- an aluminium seat frame,
- a headrest with cushion.
There are two different types of fixation for cabin attendant seats:
- floor-mounted, with seat rail,
- wall-mounted.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 64
G9409341 - GAUT0T0 - FM25D2000000002
CABIN ATTENDANT SEAT
700) Page 65

GALLEY
The buffet and galley are installed in the cabin. They are used for food
preparation and drink storing. You can install them in a number of
different configurations.
TYPE AND POWER SUPPLY
There is a wet galley unit, supplied with electrical-operated equipment
and used for food and drink preparation. And there is a dry galley
unit, only used for food, drink and equipment storing. Galleys have
specificity, like a bar, a storage or a preparation area. The galley power
supply provides the galley with 115/200V AC, 400 Hz from the AC
normal bus bars. The maximum load of each feeder is 15KVA.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 66
G9409341 - GAUT0T0 - FM25D2000000002
GALLEY - TYPE AND POWER SUPPLY
700) Page 67

GALLEY (continued)
ATTACHMENTS
The galley basic structure is made of a honeycomb panel. The main
galley attachment points are hardpoints and/or seat rail attachments
on the floor, and ties rod attachment to the upper fuselage structure.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 68
G9409341 - GAUT0T0 - FM25D2000000002
GALLEY - ATTACHMENTS
700) Page 69

GALLEY (continued)
INTERFACES
The galley has an interface with:
- water/waste system,
- galley cooling,
- passenger video entertainment system,
- galley electrical power supplies.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 70
G9409341 - GAUT0T0 - FM25D2000000002
GALLEY - INTERFACES
700) Page 71

GALLEY (continued)
EQUIPMENT
In the galley compartment there is the following equipment:
- refrigerator,
- oven,
- water heater,
- coffee maker,
- beverage maker,
- sink,
- hot cup,
- waste box,
- trolleys,
- trash compactor.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 72
G9409341 - GAUT0T0 - FM25D2000000002
GALLEY - EQUIPMENT
700) Page 73

LAVATORY
The lavatories are installed in the cabin. They are installed for the comfort
of the passengers and crew. Each lavatory also has a washroom function.
There are two types of fixation for lavatories:
- set lavatories: attached on the hardpoints. The top of the lavatories is
attached to the aircraft primary structure,
- moveable lavatories: attached to the seat rails. The tie-rods attach the
top of the lavatories to the aircraft primary structure. The attachment on
the seat rails allows different positioning of the lavatories at the
installation. The basic structure is made of a sandwich panel like the
lavatory doors.
Each door is locked with a micro switch. When the door is locked you
can open it from outside if necessary. There are single-blade doors or
bi-folding doors.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 74
G9409341 - GAUT0T0 - FM25D2000000002
LAVATORY
700) Page 75

LAVATORY (continued)
INTERFACES
Lavatories have interface with the following equipment:
- passenger address and entertainment system,
- lavatory lighting,
- fire protection system,
- light sign system,
- electrical power supply system,
- passenger oxygen system,
- Cabin Intercommunication Data System (CIDS),
- waste disposal system,
- potable water system.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 76
G9409341 - GAUT0T0 - FM25D2000000002
LAVATORY - INTERFACES
700) Page 77

COMPONENTS (PART 1/2)
These following components are found in the lavatories:
- toilet assembly,
- toilet shroud,
- hand grip,
- baby nursing table,
- toilet seat,
- toilet flush switch,
- light,
- service cabinet,
- mirror,
- soap dispenser,
- water faucet,
- washbasin,
- waste chute,
- ashtray,
- door lock,
- door.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 78
G9409341 - GAUT0T0 - FM25D2000000002
LAVATORY - COMPONENTS (PART 1/2)
700) Page 79

COMPONENTS (PART 2/2)
The following components are also included in the lavatories:
- access door,
- water heater,
- fire extinguisher,
- waste box,
- door micro switch,
- air extraction,
- emergency oxygen container,
- smoke detector,
- loudspeaker,
- individual air outlet,
- dispenser,
- PSU.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 80
G9409341 - GAUT0T0 - FM25D2000000002
LAVATORY - COMPONENTS (PART 2/2)
700) Page 81

ELECTRICAL PLUG SUPPLY
The electrical service supply is installed in the cabin and the cargo
compartments. It supplies electrical power to the socket that you can use
for electrical equipment. The electrical plug supply is installed near every
entrance door. There is an electrical razor plug supply installed in each
lavatory.
G9409341 - GAUT0T0 - FM25D2000000002
700) Page 82
G9409341 - GAUT0T0 - FM25D2000000002
ELECTRICAL PLUG SUPPLY
700) Page 83
CREW REST COMPARTMENT D/O (3)

GENERAL
The crewmembers can rest during long flights in three compartments,
the Flight Crew Rest Compartment (FCRC), the Lower Deck Mobile
Crew Rest (LD-MCR) and the Bulk Crew Rest Compartment (BCRC).
NOTE: Note: All the crew rest compartments are optional and can be
installed according to customer requests.
The FCRC is located in the cabin, behind the cockpit and ahead of the
right FWD passenger/crew door. This is a compartment for two persons
from the flight crew who can sit or lie on the installed bunks.
The LD-MCR is installed in the front part of the aft cargo compartment
and it can be removed or installed when required.
The BCRC is located in the rear part of the AFT cargo compartment. It
is installed for crew rest on long flights.
The crew can access the LD-MCR and the BCRC through staircase
housings, which are installed in the cabin.
G9409341 - GAUT0T0 - FM25D3000000002
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent CREW REST COMPARTMENT D/O (3) Aug 31, 2009
700) Page 84
G9409341 - GAUT0T0 - FM25D3000000002
GENERAL
700) Page 85

FCRC. The razor socket supplies power to an electric razor. A smoke
FLIGHT CREW REST COMPARTMENT detector is installed and it continuously monitors the condition of the
air. Optionally, a multi-function handset with a telephone and a PCU,
This topic presents the components, power supply, attachment and
and a Video Display Unit (VDU) above each bunk, can be installed.
interfaces of the FCRC.
FCRC COMPONENTS
There are two bunks. The upper bunk can be folded to the backrest
position to allow the crew to sit on the lower bunk. A belt restraint
and a curtain are installed at each bunk. The crew can use a folding
table if installed.
For stowage of coats, flight crew bags, bed sheets, pillows and
emergency equipment there are stowage compartments.
FCRC EQUIPMENT
The FCRC is equipped with:
- a minimum of one fluorescent tube with ballast unit and a minimum
of one low intensity light at the floor level,
- an EXIT sign and a minimum of one NO SMOKING/FASTEN
SEAT BELT sign,
- an emergency light controlled through the cabin emergency lighting
system,
- a Passenger Service Unit (PSU) above each bunk, and its individual
air outlet, reading light and reading light ON/OFF switch.
G9409341 - GAUT0T0 - FM25D3000000002
The PSU can be equipped with:

- a NO SMOKING/FASTEN SEAT BELT sign,
- an audio connector, a reading light dimmer control,
- an emergency oxygen container,
- a Passenger Control Unit (PCU)
- a reading light Printed Circuit Board (PCB) to supply electrical
power to the reading lights.
The Cabin Intercommunication Data System (CIDS) controls the
Additional Attendant Panel (AAP), the interphone handset and the
loudspeakers. A razor socket with static inverter is installed in the
700) Page 86
G9409341 - GAUT0T0 - FM25D3000000002
FLIGHT CREW REST COMPARTMENT - FCRC COMPONENTS & FCRC EQUIPMENT
700) Page 87

FLIGHT CREW REST COMPARTMENT (continued)
INTERFACES
The FCRC has interfaces with:
- the cabin air distribution and recirculation system,
- the CIDS,
- the individual air distribution system,
- the electrical power system,
- the auxiliary areas smoke detection system,
- the general illumination system,
- the emergency lighting system,
- the passenger oxygen system,
- the passenger attendant calls light system,
- the passenger and cabin attendant lights system.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 88
G9409341 - GAUT0T0 - FM25D3000000002
FLIGHT CREW REST COMPARTMENT - INTERFACES
700) Page 89

FLIGHT CREW REST COMPARTMENT (continued)
ATTACHMENTS
The FCRC is attached to a hard point in the cabin floor structure and
to the A/C structure with tie-rods.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 90
G9409341 - GAUT0T0 - FM25D3000000002
FLIGHT CREW REST COMPARTMENT - ATTACHMENTS
700) Page 91

LOWER DECK MOBILE CREW REST
The LD-MCR components, power supply, attachments and interfaces
will be developed.
COMPONENTS DESCRIPTION
The LD-MCR has two types of illumination, fluorescent tube with
ballast units and low intensity lights at floor level. There is an EXIT
sign near the staircase and if installed NO SMOKING/FASTEN SEAT
BELT signs.
There is a cabin interphone to allow communication between the
LD-MCR and other attendant station. The loudspeakers are connected
to the passenger address system. The CIDS controls the light through
the AAP, the interphone and the loudspeakers.
Bunks are permanently installed with belt restraints for the safety of
the crew. The bunks are separated by dividing walls and curtains.
At different locations there are stowage compartments. Some of them
contain the emergency equipment.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 92
G9409341 - GAUT0T0 - FM25D3000000002
LOWER DECK MOBILE CREW REST - COMPONENTS DESCRIPTION
700) Page 93

LOWER DECK MOBILE CREW REST (continued)
INTERFACES
The LD-MCR has interfaces with:
- the cabin air distribution and recirculation system,
- the CIDS,
- the electrical power system,
- the lower deck Cargo Loading System (CLS),
- the auxiliary-areas smoke detection system,
- the auxiliary-areas fire extinguishing system,
- the Landing Gear Control and Interface Unit (LGCIU),
- the general illumination system,
- the emergency lighting system,
- the passenger oxygen system.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 94
G9409341 - GAUT0T0 - FM25D3000000002
LOWER DECK MOBILE CREW REST - INTERFACES
700) Page 95

SYSTEM INTERFACE COMPARTMENT
The systems interface compartment is located in the lower right side
of the LD-MCR.
The compartment contains the air-conditioning connector and the
electrical systems connectors. Each interface connector has a parking
position installed in the compartment. An additional electrical systems
/ power supply connector is located in the upper front right side of
the LD-MCR.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 96
G9409341 - GAUT0T0 - FM25D3000000002
LOWER DECK MOBILE CREW REST - SYSTEM INTERFACE COMPARTMENT
700) Page 97

ATTACHMENT
When the LD-MCR is installed, it is held in its position with:
- the XZ latches at the FWD end,
- the YZ latches at the left and right hand sides,
- the retractable XZ double latches at the aft end.
The LD-MCR is operated as a classical cargo container (loading,
locking, unlocking and unloading) and has also the same shape
(dimensions).
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 98
G9409341 - GAUT0T0 - FM25D3000000002
LOWER DECK MOBILE CREW REST - ATTACHMENT
700) Page 99

LD-MCR STAIRCASE HOUSING
The staircase housing is the compartment giving access to the
LD-MCR when it is installed. A stowage compartment is installed in
the staircase housing opposite the access door.
Electrical power to the staircase housing is supplied through the A/C
interface connectors.
The staircase housing case is attached:
- to the seat tracks,
- with tie-rods from the upper attachments to the A/C structure,
- to a hard point in the cabin floor structure if necessary.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 100
G9409341 - GAUT0T0 - FM25D3000000002
LOWER DECK MOBILE CREW REST - LD-MCR STAIRCASE HOUSING
700) Page 101

BULK CREW REST COMPARTMENT (BCRC)
This topic introduces the system description, power supply, interfaces
and attachments of the BCRC.
SYSTEM DESCRIPTION
The BCRC is a permanent installation made of sub Assembles/units
and a cargo frame. It is installed on shock-mounts, which are attached
to the A/C structure. Tie-rods are attached to the BCRC and the A/C
structure and hold the BCRC in position.
The BCRC has insulation protection from cold air temperature and
to decrease the noise level.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 102
G9409341 - GAUT0T0 - FM25D3000000002
BULK CREW REST COMPARTMENT (BCRC) - SYSTEM DESCRIPTION
700) Page 103

BULK CREW REST COMPARTMENT (BCRC) (continued)
INTERFACES
The BCRC has interfaces with:
-the cabin air distribution and recirculation system,
-the Cabin Intercommunication Data System (CIDS),
-the electrical power system,
-the auxiliary-areas smoke detection system,
-the auxiliary-areas fire extinguishing system,
-the general light system,
-the emergency lighting system,
-the passenger oxygen system.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 104
G9409341 - GAUT0T0 - FM25D3000000002
BULK CREW REST COMPARTMENT (BCRC) - INTERFACES
700) Page 105

BCRC STAIRCASE HOUSING
The staircase housing is installed in the cabin Z260 above the BCRC
and the BCRC entrance hatch.
The staircase housing is attached:
-to the seat tracks,
-with tie-rods from the upper attachments to the A/C or galley
structure,
-to hard points in the cabin floor structure.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 106
G9409341 - GAUT0T0 - FM25D3000000002
BULK CREW REST COMPARTMENT (BCRC) - BCRC STAIRCASE HOUSING
700) Page 107

EMERGENCY EXIT HATCH
An emergency exit hatch is installed in the cabin z260. It can be
opened from inside the BCRC and from the cabin when the floor
covering is lifted. The emergency exit hatch lets persons leave the
BCRC when the staircase is blocked.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 108
G9409341 - GAUT0T0 - FM25D3000000002
BULK CREW REST COMPARTMENT (BCRC) - EMERGENCY EXIT HATCH
700) Page 109

AIR CONDITIONING SYSTEM/EMERGENCY OXYGEN
The cabin air distribution and recirculation system supplies air
conditioning to the FCRC and the LD-MCR. In each rest room there are
a heater, a temperature controller, a temperature selector and individual
air outlets.
Emergency oxygen containers are installed in different locations in both
crew rest compartments.
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 110
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 111
G9409341 - GAUT0T0 - FM25D3000000002
700) Page 112

G9409341 - GAUT0T0 - FM25D3000000002
700) Page 113
GALLEY TROLLEY COMPARTMENT COOLING SYSTEM D/O (3)

PRESENTATION
Each air chiller system is composed of:
- the air chiller unit,
- the water drain,
- the condenser discharge duct,
- the chilled air in and out ducting.
The air chiller system keeps food and drinks (that are stored in the trolley)
cold. The air chiller units are available with different cooling capacities.
G9409341 - GAUT0T0 - FM25D7000000003
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR TrentGALLEY TROLLEY COMPARTMENT COOLING SYSTEM D/O (3) Aug 31, 2009
700) Page 114
G9409341 - GAUT0T0 - FM25D7000000003
PRESENTATION
700) Page 115

GENERAL DESCRIPTION
The air chiller units supply chilled air to cool down the trolley
compartment in the connected galleys. Each air chiller unit is connected
to one galley only and operates independently. The chilled air is supplied
to the galley through insulated ducts. The air returning from the galley
is passed through an evaporator, chilled and return to the galley in a
closed loop. The condenser discharge duct blows the cooling air out of
the air chiller unit. The drain water of the air chiller unit drains into the
aircraft bilge drainage system or the waste-water drain system of the
galley.
G9409341 - GAUT0T0 - FM25D7000000003
700) Page 116
G9409341 - GAUT0T0 - FM25D7000000003
GENERAL DESCRIPTION
700) Page 117

ELECTRICAL CONTROL
ELECTRICAL POWER
The air chiller unit is supplied by two external electrical power supply
sources connected to a single receptacle: permanently connected 115V
AC 3 phases supply and externally switched 28V DC.
NORMAL OPERATION
A controller adjusts the chilled air out temperature by electronically
controlling a heater (that is wrapped around the thermal expansion
valve) to maintain the chilled air out temperature at -1°C/30°F. The
evaporator, refrigerant and chilled air out temperature sensors give
feedback signals to the controller.
A defrost control circuit will melt ice that has formed on the
evaporator. The defrost function is activated when ice blockage causes
the evaporator temperature to drop below a preset temperature.
PROTECTIONS
The air chiller automatically shutdowns, the ON light on the galley
control panel goes off and the fault light comes on in case of persistent:
- refrigerant LP (leak),
- refrigerant overpressure,
G9409341 - GAUT0T0 - FM25D7000000003
- fan motor overheat,

- compressor overheat.
A reset is done with the ON/OFF SW on the galley control panel.
NOTE: The protections can be cause by very hot ambient air
temperature, loss of proper cooling air circulation (dirty filter) or
incorrect electrical phase connections.
700) Page 118
G9409341 - GAUT0T0 - FM25D7000000003
ELECTRICAL CONTROL - ELECTRICAL POWER ... PROTECTIONS
700) Page 119
EMERGENCY EQUIPMENT COCKPIT D/O (3)

ESCAPE ROPE
This topic describes the emergency escape from the cockpit using the
escape rope that is located above each sliding window.
G9409341 - GAUT0T0 - FM25D4F25BF0102
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent EMERGENCY EQUIPMENT COCKPIT D/O (3) Aug 31, 2009
700) Page 120
G9409341 - GAUT0T0 - FM25D4F25BF0102
ESCAPE ROPE
700) Page 121

ESCAPE ROPE (continued)
COMPONENT DESCRIPTION
If an emergency occurs on ground, the cockpit crew can use descent
devices to leave the cockpit. When the cabin is not pressurized, each
sliding window can be opened, using a control handle, which is located
FWD of the sliding window. The windshield panels are provided with
an open-position locking system.
A 6.7 m. (22 feet) long knotted rope is located in a stowage
compartment above each sliding window. These stowage
compartments are marked by red labels. The ropes and their
attachments can support a load of 900 kg.
G9409341 - GAUT0T0 - FM25D4F25BF0102
700) Page 122
G9409341 - GAUT0T0 - FM25D4F25BF0102
ESCAPE ROPE - COMPONENT DESCRIPTION
700) Page 123

ESCAPE ROPE (continued)
REMOVAL/INSTALLATION
To remove:
- get access to the attachment ring,
- remove the screws from the ring,
- remove the rope.
To install:
- engage the loop of the rope in the ring,
- install the ring,
- put the rope in stowage,
- put the A/C back in its initial configuration.
G9409341 - GAUT0T0 - FM25D4F25BF0102
700) Page 124
G9409341 - GAUT0T0 - FM25D4F25BF0102
ESCAPE ROPE - REMOVAL/INSTALLATION
700) Page 125
EMERGENCY EQUIPMENT CABIN D/O

The cabin escape facilities are installed at all the A/C exits. They allow
quick evacuation for the passengers and the crew in case of emergency.
G9409341 - GAUT0T0 - FM25D5000000002
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent EMERGENCY EQUIPMENT CABIN D/O Aug 31, 2009
700) Page 126
G9409341 - GAUT0T0 - FM25D5000000002
700) Page 127

FLOATATION AND SURVIVAL EQUIPMENT
The floatation and survival equipment consists of the slide/rafts and the
life vests.
G9409341 - GAUT0T0 - FM25D5000000002
700) Page 128
G9409341 - GAUT0T0 - FM25D5000000002
FLOATATION AND SURVIVAL EQUIPMENT
700) Page 129

FLOATATION AND SURVIVAL EQUIPMENT (continued)
LIFE VESTS
The life vests are kept below the passenger seats and in the cabin
attendant seats. The life vests have buoyancy chambers with straps,
clips for attachment and adjustable buckles. Each life vest also has:
- two carbon-dioxide inflator cartridges with handles to fire them,
- two secondary oral inflators,
- a water-activatable light,
- a battery.
G9409341 - GAUT0T0 - FM25D5000000002
700) Page 130
G9409341 - GAUT0T0 - FM25D5000000002
FLOATATION AND SURVIVAL EQUIPMENT - LIFE VESTS
700) Page 131

SLIDE/RAFTS LOCATION
The slide/rafts are installed on each passenger/crew door and the
emergency exit doors. The slide/rafts are a combination of an escape
slide and a life raft, except for the emergency exit doors 3 type I where
there are just slides. The slide rafts inflate automatically when the
door is opened in the emergency mode.
G9409341 - GAUT0T0 - FM25D5000000002
700) Page 132
G9409341 - GAUT0T0 - FM25D5000000002
FLOATATION AND SURVIVAL EQUIPMENT - SLIDE/RAFTS LOCATION
700) Page 133

SLIDE/RAFTS DESCRIPTION
The inflatable chambers are made of heat reflecting coated fabric
tubes. The slide/raft has upper and lower structurally connected tube
assemblies. The center tube is also a lane divider. The sliding surfaces
of the lanes are not inflated. Pressure relief valves and deceleration
strips are found at the bottom of the raft. The lighting system has
directional guidance lights, which are installed on each slide/raft. They
are attached to the upper longitudinal tubes and across the bottom of
the slide/raft. The lights come on automatically when the slide/raft
inflation starts. The packed slide/raft is installed on the packboard
shell. When the door is in the ARMED mode, the girt bar is attached
to the door frame structure. When the door is in DISARMED mode,
the girt bar is attached to the door structure. A rope can be attached
on a ring in order to lower an inflated slide. A disconnection handle
located behind the girt assembly can be used to detach an inflated
slide from the aircraft.
G9409341 - GAUT0T0 - FM25D5000000002
700) Page 134
G9409341 - GAUT0T0 - FM25D5000000002
FLOATATION AND SURVIVAL EQUIPMENT - SLIDE/RAFTS DESCRIPTION
700) Page 135

PACKBOARD ASSEMBLY
The packboard shell is made of composite materials. The
mounting/release rails attach the packboard to the door structure. The
mounting rails have a quick release mechanism to separate the
packboard the slide/raft from the door structure. The Quick release
girt bar is inserted in the slide/raft girt assembly and connected to the
door with the packboard assembly .The packboard assembly has an
electrical connection with the inflation system. A viewing window
on the decorative cadre lets the pressure gauge of the inflation reservoir
be visible. A safety pin pocket (where is a transportation/ safety pin)
is available for maintenance purposes. The system comprises also a
parachute pin installed in the speed lacing and safetied with the safety
pin.
G9409341 - GAUT0T0 - FM25D5000000002
700) Page 136
G9409341 - GAUT0T0 - FM25D5000000002
FLOATATION AND SURVIVAL EQUIPMENT - PACKBOARD ASSEMBLY
700) Page 137

INFLATION SYSTEM
The inflation reservoir keeps gas (nitrogen / carbon dioxide) under
High Pressure (HP) to inflate the slide/raft. The inflation reservoir is
made of seamless aluminum. It is made stronger with over-wrapped
Kevlar fibers, which are bonded together with epoxy resin. The valve
regulator assembly is installed onto the inflation reservoir. It controls
the gas flow from the inflation reservoir to both aspirators. The
pressure gauge is installed on the valve/regulator assembly to show
the stored gas pressure.
Gas from the inflation reservoir flows through the inlet assembly of
both aspirators when the inflation system is operated. A flexible hose
connects the inflation reservoir to each aspirator assembly. A manual
inflation handle is attached with a Velcro tape on the girt assembly.
If the slide/raft does not inflate automatically when deployed over the
doorsill, you can pull the handle to inflate the slide/raft. The firing
cable opens the valve when the slide/raft is deployed. You can safety
the valve with a locking pin for maintenance. The Cabin
Intercommunication Data System (CIDS) through the DOORS page
on the Flight Attendant Panel (FAP) monitors the status of the inflation
reservoir pressure sensor and the locking pin. To avoid dysfunction,
G9409341 - GAUT0T0 - FM25D5000000002
make sure that the lighting switch pin is installed correctly.
700) Page 138
G9409341 - GAUT0T0 - FM25D5000000002
FLOATATION AND SURVIVAL EQUIPMENT - INFLATION SYSTEM
700) Page 139

RAFT EQUIPMENT
The raft equipment consists of:
- the life lines attached along the outside of the slide/raft. They are
visible to the persons in the water and do not lie flat against the tube,
- the boarding stations, attached to each side of the slide/raft. They
have boarding handles and boarding stirrups. This let a person climb
into the slide/raft from the water,
- the mooring/re-entry line, which keeps the slide/raft attached to the
A/C when the girt assembly of the slide/raft is released, and it lets a
person re-enter the A/C over an inflated slide/raft,
- the sea anchor to control the drift and to keep the slide/raft turned
into the wind,
- the survival kit composed of a base and a replacement kit,
- the emergency beacon transmitter,
- the hand pump to inflate the chambers through the inflate/deflate
valve of the slide/raft if necessary. It is used to inflate the canopy
center support tube as well,
- the canopy to give the occupants protection against different
environmental conditions and which must be installed manually. It
has a hole to collect rainwater. The canopy has a highly visible
G9409341 - GAUT0T0 - FM25D5000000002
orange/yellow color and can resist to a wind speed up to 52 knots.
700) Page 140
G9409341 - GAUT0T0 - FM25D5000000002
FLOATATION AND SURVIVAL EQUIPMENT - RAFT EQUIPMENT
700) Page 141

FIRST AID EQUIPMENT
The items of the first aid equipment are kept at different locations in the
A/C depending on the airlines request. These items include first aid kits,
physicians/doctor kit, resuscitation kit, splint pack and miscellaneous
items. Each kit is kept in a hermetically sealed waterproof container. The
expiration dates are printed on the front of the waterproof container nut.
They must be removed from the parked A/C in case of low or high
temperature to avoid any medication damages. They usually have a
five-year service life.
The resuscitation kit contains instruments for ill or injured passengers.
The splint pack contains splints and fittings to help passengers in case
of a bone fracture. Other equipment can be found such as pillows, blankets
and thermal blankets as well as an airsickness bag in the rear pocket of
each passenger seat.
G9409341 - GAUT0T0 - FM25D5000000002
700) Page 142
G9409341 - GAUT0T0 - FM25D5000000002
FIRST AID EQUIPMENT
700) Page 143

SLIDE/RAFTS DEPLOYMENT
This is the slide/rafts deployment video.
NOTE: Note: Other types of slide/raft have the same principle of

deployment as the one shown in the video.
Note: To prevent damage to the A/C, use material specified in
the AMM to protect the fuselage during deployment test.
Note: Once deployment tests are done, make sure that the slide
light supply is unplugged before removing it.
G9409341 - GAUT0T0 - FM25D5000000002
700) Page 144
G9409341 - GAUT0T0 - FM25D5000000002
SLIDE/RAFTS DEPLOYMENT
700) Page 145
LOWER DECK DECOMPRESSION SAFETY SYSTEM

The rapid decompression panels (blow-in/blow-out) are installed in the
sidewall panels and in the fixed partition walls. They prevent damage to
the aircraft structure in case of sudden pressure difference. The system
prevents a pressure difference between different areas in the aircraft
(cockpit/cabin, or cabin/cargo compartment-. The panels have a composite
structure made of a honeycomb-core and a flame-retardant laminated-skin.
Foam-tape is bonded into the recess of the panel border and makes a seal
between the panel and the frame. There is a flame-retardant strip between
the Foam-tape and the border edge. Some frames have protective devices.
The Panel assemblies include a panel, a frame and fastener assemblies.
The fastener assemblies are attached to the frames and include some
latches, springs and catches.
G9409341 - GAUT0T0 - FM25DD000000001
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent LOWER DECK DECOMPRESSION SAFETY SYSTEM Aug 31, 2009
700) Page 146
G9409341 - GAUT0T0 - FM25DD000000001
700) Page 147

RAPID DECOMPRESSION PANELS
If a rapid-decompression occurs in the cargo compartment, the higher
air pressure pushes the panel assemblies against their fasteners.
This force will release the catches and the panel assemblies are blown
inboard (Blow-in). The higher air pressure can flow from the cabin to
the Cargo Compartment.
If a rapid-decompression occurs in the Cabin, the higher air pressure
pushes the panel against their fasteners.
This force will release the catches and the panels are blown outboard
(Blow-out). The higher air pressure can flow from the cargo compartment
to the Cabin.
G9409341 - GAUT0T0 - FM25DD000000001
700) Page 148
G9409341 - GAUT0T0 - FM25DD000000001
RAPID DECOMPRESSION PANELS
700) Page 149

RESET
The reset of rapid decompression panel is done by one pressure on the
panel. During this operation, the catch recoils and rotates at the same
time. The catch is held and locked with the help of leaf spring.
Once this operation is carried out, the panel returns into its initial position.
The system of reset on the panel and on the frame is identical.
G9409341 - GAUT0T0 - FM25DD000000001
700) Page 150
G9409341 - GAUT0T0 - FM25DD000000001
RESET
700) Page 151
LOWER DECK CARGO LOADING SYSTEM D/O (3)

DESCRIPTION
The semi-automatic Cargo Loading System (CLS) of the FWD and aft
cargo compartments is used for loading, unloading and moving the Unit
Load Devices (ULDs). These ULDs can be pallets or containers of
different sizes. One person can operate the CLS. If there is no electrical
power available, it is possible to load or unload manually. The
semi-automatic CLSs of the FWD and aft lower deck cargo compartments
are similar in construction and equivalent in operation.
The CLS has:
- transport components,
- latching components,
- control components,
- guiding components.
G9409341 - GAUT0T0 - FM25D6000000003
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent LOWER DECK CARGO LOADING SYSTEM D/O (3) Sep 07, 2009
700) Page 152
G9409341 - GAUT0T0 - FM25D6000000003
DESCRIPTION
700) Page 153

DESCRIPTION (continued)
TRANSPORT COMPONENTS
The components to convey the ULDs are:
- six roller tracks installed. They are part of the floor structure. The
ULDs move on these roller tracks. They incorporate free running
rollers and braking rollers. The braking rollers slow the movements
of the ULDs for safety reasons.
- the ball mats extend across the full length of the entrance area and
across the full width of the compartment. They are used for the ULDs
change of direction during loading and unloading. Ball mats and ball
strips have light alloy plates, which contain a number of ball units.
The ball mats are installed between the roller tracks, and the ball strips
in the roller tracks.
- the sensorized Power Drive Units (PDUs) are installed for movement
of the ULDs in the lateral and longitudinal direction. The PDUs have
self-lifting rollers. The PDUs are equipped with a sensorized control
device which functions as a ULD scanning device. The scanning
device is an integrated part of the PDU and its internal printed circuit
boards. When the ULD moves over the PDU it triggers the scanning
device, which causes the roller to come up and move the ULD. When
the ULD has moved over the PDU the scanning devices goes on
G9409341 - GAUT0T0 - FM25D6000000003
standby and the rollers retract.

- the other type of PDUs are installed for movement of the ULDs in
the longitudinal direction. The PDUs have self-lifting rollers. Electrical
AC power supplies the PDUs. When the adjacent latch is lowered,
the PDU is energized and its drive roller is lifted until it touches the
bottom of the ULDs. When the unit is de-energized or its adjacent
latch is lifted, the roller stops and is lowered under system weight.
700) Page 154
G9409341 - GAUT0T0 - FM25D6000000003
DESCRIPTION - TRANSPORT COMPONENTS
700) Page 155

- The Y-guide switch is used to unlock the Y-guides in the load
DESCRIPTION (continued) direction. For unloading, the Y-guides are overridable.
- The Y-guide load light comes on when one or more Y-guides are
LATCHING COMPONENTS
inoperative.
The latching components are installed on the floor of the compartment.
They are used for the ULDs locking. They are identified to show in
which direction they have an effect:
- X > longitudinal,
- Y > transversal,
- Z > vertical.
There are three types of latches:
- the doorsill latches. They are provided in the doorsills to lock the
ULDs in the lateral and vertical directions. They incorporate two
different types of latches: the manually operated YZ latches and the
overridable Y latches. When unloading containers, the doorsill latch
releases lever must be operated for each container to lower the Y
latches. This is installed to avoid movement of ULDs during
unloading.
- the manually operated and overridable YZ latches. They are installed
on the A/C centerline to hold the half width ULDs in the lateral and
vertical directions. The overridable YZ latches are lowered against
spring pressure when a full width ULD is moved over them. The
manually operated YZ latches are installed on the A/C centerline in
G9409341 - GAUT0T0 - FM25D6000000003
the ball mat area. They must be lowered for loading and unloading.
- the XZ single, double and fixed latches. They are installed in the
roller tracks to hold the ULDs in longitudinal and vertical directions.
The single and double latches are manually operated. When they are
lifted, the PDUs behind this latch row are turned off. The fixed XZ
latches are installed in the roller tracks at the wing-box end of the
compartment. They operate as stops for the ULDs and protection for
the partition wall.
The AFT cargo compartment control panel is similar to the FWD one
except the control and indicating system of the Y-guides:
700) Page 156
G9409341 - GAUT0T0 - FM25D6000000003
DESCRIPTION - LATCHING COMPONENTS
700) Page 157

- the proximity switches. They are attached to the related XZ latches.
DESCRIPTION (continued) When you lift these XZ latches, you electrically isolate the related
PDU. This inhibits the operation of the PDU when the ULD is latched
CONTROL COMPONENTS
in position.
There are four different control components:
The control panel, located behind a service door adjacent to the cargo
compartment door, has:
- the sill lock lever, which is used to unlock the overrideable Y-latches
of the cargo compartment doorsill,
- the power switch, which is used to energize/de-energize the cargo
loading system,
- the joystick.
The inside control panel, which is installed in the ceiling panel adjacent
to the cargo door, has a two-way joystick. It is used for the control of
the ULDs movements on the roller tracks. It has two positions: FWD
and aft. The Power Drive Units are energized only if the joystick is
activated.
The control box is installed above the housing of the control panel. It
gives all signals to the related components.
The C/B panel is installed in the ceiling, near the cargo compartment
door.
The Maintenance Display Unit (MDU) is installed in the service panel
5022VE and will indicate relevant maintenance data. The display is
G9409341 - GAUT0T0 - FM25D6000000003
designed to indicate the data in two lines of twenty characters. The

MDU is linked via a network to the controller components. The MDU
indicates failures of the electrical components, the PDUs, the proximity
switches and the control panels.
There are two different types of switches used for the CLS:
- the mechanical switches. They are attached to the YZ latches in the
doorsill and they are connected in series. When the YZ latches are
locked in the lifted position, you can operate the cargo compartment
door but the CLS is electrically isolated. When the YZ latches are
lowered, the cargo compartment door mechanism is electrically
isolated but the CLS is operative.
700) Page 158
G9409341 - GAUT0T0 - FM25D6000000003
DESCRIPTION - CONTROL COMPONENTS
700) Page 159

GUIDING COMPONENTS
The guiding components are identified to show in which direction
they have an effect:
- X > longitudinal,
- Y > transversal,
- Z > vertical.
There are four types of guiding components:
- the entrance guide installed at the doorsill allows proper guiding of
the ULDs and protect the doorframe. The guide has a sloped front
plate with four vertical guide rollers. The guide rail is hinge-attached
to the nearest fixed YZ guide to the entrance.
- the XY guides installed at the cargo doorsill. The guide has a sloped
front plate with a guide roller to absorb shocks and a guide-rail with
two guide rollers. The guide-rail is hinge-attached to the nearest fixed
YZ latch located at the cargo door entrance.
- the continuous side guides are installed between the fixed YZ latches
along the cargo compartment.
- the fixed YZ guides. A row of five YZ guides and two guide-rails
are installed at the end of the roller tracks at the cargo door entrance.
They are used like YZ guides when you load or unload the ULD, as
G9409341 - GAUT0T0 - FM25D6000000003
XZ latches when the ULDs are locked in position, and to protect the
end wall of the cargo compartment. Each YZ guide can have one or
two vertical guide rollers and each Y guide-rail has two vertical guide
rollers.
The retractable Y guides are installed on the A/C centerline to align
the half-width ULDs. The retractable Y guide is overridable in one
way. You can retract and lift them manually.
700) Page 160
G9409341 - GAUT0T0 - FM25D6000000003
DESCRIPTION - GUIDING COMPONENTS
700) Page 161

DRAINAGE
The FWD, aft and bulk cargo compartments have a drainage system
that collects fluids and drains them through the bilge area into drain
valves. The drain valves are installed at the bottom of the fuselage. If
the cabin pressure is below a given value i.e. the A/C is near to or on
the ground, a spring holds the valves open. The fluids drain out and
are removed by the airflow or gravity. If the cabin pressure is above
a given value i.e. the A/C is in flight, the drain valves close
automatically.
G9409341 - GAUT0T0 - FM25D6000000003
700) Page 162
G9409341 - GAUT0T0 - FM25D6000000003
DESCRIPTION - DRAINAGE
700) Page 163

SYSTEM SET UP
This is system set up video.
A-M PALLET OPERATION

This is A-M pallet operation video.
SINGLE LD3 OPERATION

This is single LD3 operation video.
LD3 PAIRED OPERATION

This is LD3 paired operation video.
G9409341 - GAUT0T0 - FM25D6000000003
700) Page 164

G9409341 - GAUT0T0 - FM25D6000000003
700) Page 165
EQUIPMENT/FURNISHINGS SYSTEM BASE MAINTENANCE (3)

EMERGENCY ESCAPE SLIDE REMOVAL AND
REPLACEMENT
SAFETY PRECAUTIONS
WARNING: BEFORE YOU START WORK ON THE DOOR MAKE

SURE THAT:
- THE EMERGENCY CONTROL HANDLE IS IN THE
DISARMED POSITION WITH THE SAFETY PIN
INSTALLED,
- THE PERCUSSION LEVER OF THE DOOR
DAMPER AND EMERGENCY OPERATION
CYLINDER IS IN THE DISARMED POSITION WITH
THE SAFETY PIN INSTALLED.
THIS MAKES SURE THAT THE DOOR DOES NOT
OPEN SUDDENLY. IF THE DOOR OPENS
SUDDENLY IT CAN CAUSE INJURY AND/OR
DAMAGE.
MAKE SURE THAT THE SAFETY/LOCK PIN IS
CORRECTLY INSTALLED IN THE REGULATOR
VALVE ASSEMBLY OF THE INFLATION
RESERVOIR. THIS PREVENTS ACCIDENTAL:
G9409341 - GAUT0T0 - FM25Y2BASEMCE03
- DISCHARGE OF THE INFLATION RESERVOIR,

- DEPLOYMENT OF THE ESCAPE SLIDE.
THIS CAN CAUSE INJURY AND/OR DAMAGE.
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent EQUIPMENT/FURNISHINGS SYSTEM BASE MAINTENANCE (3) Aug 31, 2009
700) Page 166
EMERGENCY ESCAPE SLIDE REMOVAL AND REPLACEMENT - SAFETY PRECAUTIONS
700) Page 167

REPLACEMENT (continued)
PASSENGER/CREW DOOR (TYPE A) SLIDE REMOVAL
PROCEDURE
CAUTION: DURING THE FOLLOWING PROCEDURE DO NOT

OPEN THE DOOR.
IF YOU DO SO, YOU WILL START THE SEQUENCE
OF STEPS THAT PULLS THE INFLATABLE
ASSEMBLY OUT OF THE PACK-ASSEMBLY.
DO NOT PULL THE GIRT ASSEMBLY. IF YOU DO
SO, YOU WILL OPEN THE PACK-ASSEMBLY.
SUPPORT THE UNIT CAREFULLY TO PREVENT
INJURY TO PERSONS AND DAMAGE. THE UNIT
IS HEAVY.
Remove the slide safety pin, and set the control handle to the
ARMED/AUTOMATIC position. Then remove the quick-release bar
by pushing the release lever of the door to separate the girt assembly
from the door. The release lever is located at the bottom left corner
of the door.
To remove the pack-assembly, loosen the screws, hold the unit to

disengage the rails from the hooks, then put the pack-assembly on the
cabin floor. Disconnect the electrical connector and install blanking
caps.
Re-fit the quick-release bar into the girt bar by pulling the release
lever.
Set the emergency control handle to the DISARMED/MANUAL
position and install the slide safety pin. Carefully lift the door by using
the door control handle. Confirm that the girt bar is attached to the
lockjaw, then close the door again.
You can now remove the pack-assembly from the A/C.
700) Page 168
EMERGENCY ESCAPE SLIDE REMOVAL AND REPLACEMENT - PASSENGER/CREW DOOR (TYPE A) SLIDE REMOVAL PROCEDURE
700) Page 169
700) Page 170
700) Page 171
700) Page 172
700) Page 173
700) Page 174

700) Page 175

PRE-FIT INSPECTION BEFORE INSTALLATION OF
THE ESCAPE FACILITIES
Before installation, you must check that the pack-assembly is
serviceable. If installation is at a door where the escape-slide/raft has
been deployed, make sure that the diaphragm is replaced in the
percussion mechanism of the door damper and emergency exit.
Make sure that emergency lights are in good condition. In the cockpit,
the EMER EXIT LT switch is set to the OFF position.
To do a door maintenance, make sure that the door handle and the
attached slide/raft activating system are disarmed.
Inspect the new pack-assembly, and check that the inflation reservoir
is safetied.
Install the pack-assembly in front of the door. Check and clean the
component interface and adjacent area.
Make sure the lighting-switch pin is correctly installed. If necessary,
push it into the housing until a click is heard.
Check the gage indicates a correct pressure. Model A gage has a green
cursor which is temperature sensitive and the model B gage has a
needle with an internal mechanism which is temperature sensitive.

Check the release pin installation and make sure that the parachute
pin is installed in the speed lacing and safetied.
Make sure that the electrical harness is correctly connected to the
pack-assembly.
CAUTION: IF THE ELECTRICAL HARNESS IS NOT

CORRECTLY INSTALLED, IT CAN PREVENT THE
CORRECT INFLATION AND/OR DEPLOYMENT OF
THE ESCAPE SLIDE RAFT.
You can now fit the pack assembly onto the door.
700) Page 176
EMERGENCY ESCAPE SLIDE REMOVAL AND REPLACEMENT - PRE-FIT INSPECTION BEFORE INSTALLATION OF THE ESCAPE
FACILITIES
700) Page 177
FACILITIES
700) Page 178
FACILITIES
700) Page 179
FACILITIES
700) Page 180
FACILITIES
700) Page 181
FACILITIES
700) Page 182
FACILITIES
700) Page 183
FACILITIES
700) Page 184
FACILITIES
700) Page 185

INSTALLATION PROCEDURE (TYPE A DOOR) FOR
THE ESCAPE FACILITIES
WARNING: DURING THIS PROCEDURE, USE PROTECTIVE

CLOTHING, RUBBER GLOVES, GOGGLES AND
MASK BEFORE YOU APPLY SPECIFIC
MATERIALS. DO NOT PULL THE GIRT
ASSEMBLY. IF YOU DO SO, YOU WILL OPEN THE
PACK-ASSEMBLY.
Remove the slide safety pin, and set the control handle to the
ARMED/AUTOMATIC position. Remove the quick-release bar from
the door by pushing the release lever.
Carefully push the quick-release bar into the girt assembly.
To install the pack-assembly onto the door, connect the electrical
connector, lift the pack and engage the release rails onto the hooks.
The pack must be secured by screws with specific materials.
Install the quick-release bar into the girt bar and pull the release lever
away from the door to lock it in position.
Then set the emergency control handle to the DISARMED/MANUAL

position and secure it with the slide safety pin.
Do a visual check of the installation:
- girt assembly attached with burr-strip,
- girt bar attached with lockjaw.
Perform an operational test of the emergency lights and test the escape
facilities pressure indication on the Flight Attendant Panel (FAP).
If no other equipment/furnishings tasks have to be performed, the area
can be closed, making sure that all tools, test and support used during
this procedure have been removed.
700) Page 186
EMERGENCY ESCAPE SLIDE REMOVAL AND REPLACEMENT - INSTALLATION PROCEDURE (TYPE A DOOR) FOR THE ESCAPE
FACILITIES
700) Page 187
FACILITIES
700) Page 188
FACILITIES
700) Page 189
FACILITIES
700) Page 190
FACILITIES
700) Page 191
FACILITIES
700) Page 192
FACILITIES
700) Page 193
FACILITIES
700) Page 194

700) Page 195

EXIT DOOR (TYPE 1) SLIDE REMOVAL AND
REPLACEMENT
The procedure for removal and installation is similar to a Type A
door.
700) Page 196
EMERGENCY ESCAPE SLIDE REMOVAL AND REPLACEMENT - EXIT DOOR (TYPE 1) SLIDE REMOVAL AND REPLACEMENT
700) Page 197

DOOR AREA HEATING SYSTEM MAINTENANCE
DOOR AREA HEATING SYSTEM BITE
The heated floor panel system can be tested through the MCDU.
On the MCDU, perform the GND SCANNING in CABIN menu, wait
180 s. Make sure that the "NO FAULT DETECTED" messages comes
on.
If no other equipment/furnishing tasks have to be performed, the area
can be closed, making sure that all tools, test and support used during
this procedure have been removed.
700) Page 198
DOOR AREA HEATING SYSTEM MAINTENANCE - DOOR AREA HEATING SYSTEM BITE
700) Page 199
700) Page 200
700) Page 201
LININGS & FURNISHINGS REMOVAL/INSTALLATION (3)

DADO PANELS
REMOVAL OF THE DADO PANELS
NOTE: this procedure is the same for all types of Dado panels.
Release the studs with a spike.
Pull the Dado panel in the inboard direction to release it from the
support.
Carefully remove the Dado panel.
G9409341 - GAUT0T0 - FM25Y3000000001
MECHANICAL & AVIONICS COURSE - T1+T2 (LVL 2&3) (RR Trent LININGS & FURNISHINGS REMOVAL/INSTALLATION (3) Aug 31, 2009
700) Page 202
G9409341 - GAUT0T0 - FM25Y3000000001
DADO PANELS - REMOVAL OF THE DADO PANELS
700) Page 203
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 204
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 205

DADO PANELS (continued)
INSTALLATION OF THE DADO PANELS
NOTE: this procedure is the same for all types of Dado panels.
Make sure that the work area is clean and clear of tools and other
items.
Carefully push the Dado panels in the outboard direction to engage
it on the pins of the support.
Push the studs in until they lock into the floor angle.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 206
G9409341 - GAUT0T0 - FM25Y3000000001
DADO PANELS - INSTALLATION OF THE DADO PANELS
700) Page 207
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 208
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 209
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 210

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 211

SIDEWALL PANELS
REMOVAL OF THE SIDEWALL PANEL
NOTE: the removal procedure is applicable for the LH and RH

sidewall panels and for all types of the sidewall panels.
Pull the infillstrips out at the top of the sidewall panel.
Remove the screws at the top of the sidewall panel.
Carefully pull the sidewall panel inboard to release the retainers from
the support.
Remove the sidewall panel.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 212
G9409341 - GAUT0T0 - FM25Y3000000001
SIDEWALL PANELS - REMOVAL OF THE SIDEWALL PANEL
700) Page 213
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 214
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 215
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 216
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 217

SIDEWALL PANELS (continued)
INSTALLATION OF THE SIDEWALL PANELS
NOTE: the installation procedure is applicable for the LH and RH

sidewall panels and for all types of sidewall panels.
items.
Make sure the window foam ring is properly installed.
Push the sidewall panel down to engage the retainers in the support.
Install and tighten the screws at the top of the sidewall panel.
Install the infillstrips at the top and between the sidewall panels.
Check the clearance between the two-sidewall panels (10.0+2.0-2.0
mm).
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 218
G9409341 - GAUT0T0 - FM25Y3000000001
SIDEWALL PANELS - INSTALLATION OF THE SIDEWALL PANELS
700) Page 219
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 220
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 221
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 222
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 223
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 224
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 225

LIGHT COVERS
REMOVAL OF THE LIGHT COVERS
NOTE: the removal procedure of the lateral light covers is the same
for the left and the right sides.
Remove the plastic covers from the quick release fasteners, without
using a sharp tool.
Loosen the quick release fasteners.
Carefully remove the lateral light cover towards the inboard direction.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 226
G9409341 - GAUT0T0 - FM25Y3000000001
LIGHT COVERS - REMOVAL OF THE LIGHT COVERS
700) Page 227
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 228
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 229
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 230

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 231

LIGHT COVERS (continued)
INSTALLATION OF THE LIGHT COVERS
items.
Carefully put the lateral light cover in position. Slide the lower part
between the sidewall panel and the clips.
Fasten the quick release fasteners and put the plastic covers back.
Make sure that:
- the lateral light cover is correctly attached,
- there is a sufficient overlap of the sealing lips,
- the sealing lips are not twisted,
- there is a sufficient gap to the adjacent lateral light covers,
- the gap between the lateral light covers is in line with the gap
between the adjacent sidewall linings.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 232
G9409341 - GAUT0T0 - FM25Y3000000001
LIGHT COVERS - INSTALLATION OF THE LIGHT COVERS
700) Page 233
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 234
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 235
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 236
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 237

PASSENGER SERVICE UNIT (PSU)
REMOVAL OF A PSU
To open the PSU: at the aisle side of the PSU, carefully bend the
rubber strip down and loosen the screws counter clockwise of one
and a quarter. To unscrew, use a screwdriver with phillips head.
Carefully lower the PSU and disconnect the electrical connectors.
Lift and hold the PSU, loosen and unlock the remaining screws from
the mounting rail and remove the PSU.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 238
G9409341 - GAUT0T0 - FM25Y3000000001
PASSENGER SERVICE UNIT (PSU) - REMOVAL OF A PSU
700) Page 239
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 240
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 241
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 242

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 243

PASSENGER SERVICE UNIT (PSU) (continued)
INSTALLATION OF A PSU
Put the PSU in position and engage the locking devices in the
mounting rail. Make sure that you hear a click when locking devices
are being locked.
Make sure that the electrical connectors are clean and in good
condition then connect it.
items. Lift the PSU in position and engage the remaining locking
devices in the mounting rail. Make sure you hear the click.
Torque the screws to the 0.1 m.daN with a screwdriver-torque.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 244
G9409341 - GAUT0T0 - FM25Y3000000001
PASSENGER SERVICE UNIT (PSU) - INSTALLATION OF A PSU
700) Page 245
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 246
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 247
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 248
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 249

HANDRAIL
REMOVAL OF THE HANDRAIL
Open the related stowage compartment door to get access to the
screws, hold the handrail and remove the screws.
Remove the handrail.
NOTE: some handrails are equipped with cabin temperature sensors.

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 250
G9409341 - GAUT0T0 - FM25Y3000000001
HANDRAIL - REMOVAL OF THE HANDRAIL
700) Page 251
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 252
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 253

HANDRAIL (continued)
INSTALLATION OF THE HANDRAIL
Put the handrail in position on the overhead stowage compartment,
and install the screws.
NOTE: check the lip seal installation.

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 254
G9409341 - GAUT0T0 - FM25Y3000000001
HANDRAIL - INSTALLATION OF THE HANDRAIL
700) Page 255
G9409341 - GAUT0T0 - FM25Y3000000001
HANDRAIL - INSTALLATION OF THE HANDRAIL
700) Page 256

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 257

OVERHEAD STOWAGE COMPARTMENT-DOOR
REMOVAL OF THE OVERHEAD
STOWAGE-COMPARTMENT-DOOR
NOTE: the removal procedure for all the stowage-compartment door

types is the same.
Open the door and hold it in position.
Remove the screws, the washers from the hinges.
Carefully remove the door.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 258
G9409341 - GAUT0T0 - FM25Y3000000001
OVERHEAD STOWAGE COMPARTMENT-DOOR - REMOVAL OF THE OVERHEAD STOWAGE-COMPARTMENT-DOOR
700) Page 259
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 260
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 261
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 262

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 263

(continued)
INSTALLATION OF THE OVERHEAD
NOTE: the installation procedure for all the stowage-compartment

door types is the same.
Put the door in position on the hinges, and install the washers and the
screws.
If necessary, adjust and align the stowage compartment door (refer
to AMM 25-24-61-820-801).
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 264
G9409341 - GAUT0T0 - FM25Y3000000001
OVERHEAD STOWAGE COMPARTMENT-DOOR - INSTALLATION OF THE OVERHEAD STOWAGE-COMPARTMENT-DOOR
700) Page 265
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 266
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 267

(continued)
ADJUSTEMENT OF THE OVERHEAD
Make sure that the door end is aligned with the end of the handrail
and the dimension X is correct, if not:
- loosen the screws,
- move the door until it is aligned with the end of the handrail and
dimension X is correct,
- then tighten the screws.
Open the door, and make sure that the dimension Z is correct, if not:
- turn the screws clockwise to move the door up and counter clockwise
to move the door down.
Make sure the door locks correctly, if not:
- loosen the screws,
- and adjust the door-keeper-latch to the required position,
- then tighten the screws.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 268
G9409341 - GAUT0T0 - FM25Y3000000001
OVERHEAD STOWAGE COMPARTMENT-DOOR - ADJUSTEMENT OF THE OVERHEAD STOWAGE-COMPARTMENT-DOOR
700) Page 269
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 270
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 271
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 272

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 273

CLOSING COVERS (AIR OUTLET)
REMOVAL OF THE CLOSING COVERS (AIR OUTLET)
CAUTION: do not use too much force when you remove the cover
as this can cause damage to the retainer.
NOTE: this procedure is the same for all closing covers on the left
and right sides.
Carefully move the closing cover inboard to disengage the retainers,
and pull it down until they are released from the ceiling panel.
Carefully pull the closing cover inboard to release the retainers from
the supports.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 274
G9409341 - GAUT0T0 - FM25Y3000000001
CLOSING COVERS (AIR OUTLET) - REMOVAL OF THE CLOSING COVERS (AIR OUTLET)
700) Page 275
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 276
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 277
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 278

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 279

CLOSING COVERS (AIR OUTLET) (continued)
INSTALLATION OF THE CLOSING COVERS (AIR
OUTLET)
NOTE: this procedure is the same for all closing covers left and
right.
Make sure the work area is clean and clear of tools and other items.
Put the closing cover in position and carefully engage the retainers
into the supports.
Carefully push the closing cover up to engage all retainers correctly
into the ceiling panel.
Make sure that:
- the closing cover is correctly attached,there is a sufficient overlap
of the sealing lips,
- the sealing lips are not twisted,
- there is a sufficient gap to the adjacent closing covers,
- the gap between the closing covers is in line with the gap between
the adjacent ceiling panels.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 280
G9409341 - GAUT0T0 - FM25Y3000000001
CLOSING COVERS (AIR OUTLET) - INSTALLATION OF THE CLOSING COVERS (AIR OUTLET)
700) Page 281
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 282
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 283
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 284
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 285

CEILING PANELS
REMOVAL OF THE CEILING PANELS
Unlock the fasteners and hold the ceiling panel.
Carefully pull the ceiling panel outboard and remove it from the
support.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 286
G9409341 - GAUT0T0 - FM25Y3000000001
CEILING PANELS - REMOVAL OF THE CEILING PANELS
700) Page 287
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 288
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 289

CEILING PANELS (continued)
INSTALLATION OF THE CEILING PANELS
Make sure the work area is clean and clear of tools and other items.
Move the ceiling panel to engage the retainers into the supports.
Lift the ceiling panel and lock the fasteners. Make sure the sealing lip
is not twisted.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 290
G9409341 - GAUT0T0 - FM25Y3000000001
CEILING PANELS - INSTALLATION OF THE CEILING PANELS
700) Page 291
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 292
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 293
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 294

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 295

INSTALLATION OF RAPID-DECOMPRESSION PANELS
AFTER ONE PART OF THE PANEL HAS BEEN
ACCIDENTALLY DISENGAGED.
NOTE: the panel assembly includes a frame, a panel and fasteners.

To remove the panel assembly, push in the disengage part of the panel
and put your fingers behind the frame. Carefully pull the frame and the
panel, out from the sidewall panel into the cargo compartment.
To separate the panel from the frame, put the frame on the flat surface
with the panel on the top. Push backwards each latch to disengage the
catch from the panel, separate the panel from the frame.
To reset the fasteners, put the frame on a flat surface with the fasteners
on the topside. Push all catches that are in the disengaged position to the
closed position.
To assemble the panel and the frame back together, put the panel on the
center of the catches on the frame. Carefully push the panel until each
catch engages. You can hear a click sound when each catch engages
correctly.
To put the panel assembly back in the sidewall panel, carefully push the
panel assembly until each catch engages. You can hear a click sound
when each catch engages correctly.
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 296
G9409341 - GAUT0T0 - FM25Y3000000001
INSTALLATION OF RAPID-DECOMPRESSION PANELS AFTER ONE PART OF THE PANEL HAS BEEN ACCIDENTALLY DISENGAGED.
700) Page 297
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 298
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 299
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 300
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 301
G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 302

G9409341 - GAUT0T0 - FM25Y3000000001
700) Page 303
AIRBUS S.A.S.
31707 BLAGNAC cedex, FRANCE
STM
REFERENCE G9409341
SEPTEMBER 2009
PRINTED IN FRANCE
AIRBUS S.A.S. 2009
ALL RIGHTS RESERVED
AN EADS COMPANY

Ata25 Airbus

Uploaded by

Copyright:

Available Formats

Ata25 Airbus

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ata25 Airbus

Uploaded by

Copyright:

Available Formats

Under no circumstances should this document be used as a reference

It will not be updated.

All rights reserved

AIRBUS Environmental Recommendation

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

SYSTEM OVERVIEW - CABIN PANEL LAYOUT

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

SYSTEM OVERVIEW - CABIN ESCAPE FACILITIES

SYSTEM OVERVIEW - CABIN ESCAPE FACILITIES

This Page Intentionally Left Blank

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

SYSTEM OVERVIEW - LOWER DECK CARGO COMPARTMENTS

SYSTEM OVERVIEW - LOWER DECK CARGO COMPARTMENTS

This Page Intentionally Left Blank

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

SYSTEM OVERVIEW - LOWER DECK CARGO LOADING SYSTEM (CLS)

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

NOTE: The number of inoperative doors on the aircraft changes

NOTE: : SOME AIRLINES PUT THE WBM LIMITS AND

RESTRICTIONS IN THE MEL CHAPTER 25

CAUTION: In the case of malfunction of any part of the cargo loading

This Page Intentionally Left Blank

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

MAINTENANCE TIPS - SAFETY THE DOOR CYLINDER PERCUSSION MECHANISM

MAINTENANCE TIPS - SAFETY THE DOOR CYLINDER PERCUSSION MECHANISM

This Page Intentionally Left Blank

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

MAINTENANCE TIPS - DISARM THE DOOR ESCAPE SLIDE RESERVOIR

EQUIPMENT/FURNISHINGS LINE MAINT BRIEFING

NOTE: If a decompression panel is damaged, do a repair or replace

NOTE: If a lining panel is damaged, do a repair or replace the panel.

COCKPIT D/O (3)

into two parts:

PILOT SEATS - DESCRIPTION

COCKPIT D/O (3)

PILOT SEATS - OPERATION & ATTACHMENT

COCKPIT D/O (3)

THIRD OCCUPANT SEAT

COCKPIT D/O (3)

FOURTH OCCUPANT SEAT - DESCRIPTION ... ATTACHMENT

PASSENGER COMPARTMENT D/O (3)

PASSENGER COMPARTMENT D/O (3)

LINING AND FURNISHING PANELS

PASSENGER COMPARTMENT D/O (3)

LINING AND FURNISHING PANELS - DECOMPRESSION

PASSENGER COMPARTMENT D/O (3)

LINING AND FURNISHING PANELS - INSULATION

PASSENGER COMPARTMENT D/O (3)

LINING AND FURNISHING PANELS - HEATED FLOOR PANEL SYSTEM (HFPS)

LINING AND FURNISHING PANELS - HEATED FLOOR PANEL SYSTEM (HFPS)

LINING AND FURNISHING PANELS - HEATED FLOOR PANEL SYSTEM (HFPS)

PASSENGER COMPARTMENT D/O (3)

LINING AND FURNISHING LAYOUT

PASSENGER COMPARTMENT D/O (3)

LINING AND FURNISHING LAYOUT - SEPARATION AND OVERHEAD STOWAGE

PASSENGER COMPARTMENT D/O (3)

PASSENGER SERVICE CHANNEL

PASSENGER COMPARTMENT D/O (3)

PASSENGER SERVICE CHANNEL - PSIU INTERFACES