PowerFlex700DC en

PowerFlex® Digital DC Drive
USER MANUAL
Firmware Version 1.006 - 2.001

Important User Information Solid state equipment has operational characteristics differing from those of
electromechanical equipment. Safety Guidelines for the Application,
Installation and Maintenance of Solid State Controls (Publication SGI-1.1
available from your local Rockwell Automation sales office or online at http://
www.rockwellautomation.com/literature) describes some important differences
between solid state equipment and hard-wired electromechanical devices.
Because of this difference, and also because of the wide variety of uses for solid
state equipment, all persons responsible for applying this equipment must
satisfy themselves that each intended application of this equipment is
acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect
or consequential damages resulting from the use or application of this
equipment.
The examples and diagrams in this manual are included solely for illustrative
purposes. Because of the many variables and requirements associated with any
particular installation, Rockwell Automation, Inc. cannot assume responsibility
or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use
of information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without
written permission of Rockwell Automation, Inc. is prohibited.
Throughout this manual, when necessary we use notes to make you aware of
safety considerations.
WARNING: Identifies information about practices or

! circumstances that can cause an explosion in a hazardous
environment, which may lead to personal injury or death, property
damage, or economic loss.
Important: Identifies information that is critical for successful application and

understanding of the product.
ATTENTION: Identifies information about practices or

! circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard,
avoid a hazard, and recognize the consequences.
Shock Hazard labels may be located on or inside the equipment

(e.g., drive or motor) to alert people that dangerous voltage may be
present.
Burn Hazard labels may be located on or inside the equipment

(e.g., drive or motor) to alert people that surfaces may be at
dangerous temperatures.
PowerFlex, DriveExplorer, DriveTools SP, DPI, and SCANport are either trademarks or registered trademarks of Rockwell Automation, Inc.
Klixon® is a registered trademark of Sensata Technologies, Inc.
PowerFlex Digital DC Drive User Manual

Summary of Changes
Manual Updates The information below summarizes the changes to the PowerFlex Digital
DC Drive User Manual, publication 20-UM001… since the October 2007
release.
Change Page(s)
Updated the Using Contactors section to include new Contactor Control selections 1-9
for configuring AC versus DC contactors.
Added the “Cable and Wiring Recommendations” table. 1-14
Updated the “Typical Power Wiring Diagrams” to include terminal and parameter 1-17
designations.
Added “Sourcing Digital Outputs, 24V DC external supply” diagram to I/O Wiring 1-39
examples.
Added an illustration and instructions for routing I/O and control wiring. 1-42
Added a graphical indicator for parameters accessible only when parameter 211 3-1
[Param Access Lvl] = 1 “Advanced”.
Added parameter 1409 [Jog Off Delay], to allow you to specify the minimum delay 3-24
between removing the Jog input and commanding the main contactor to open.
This delay reduces the wear on the contactor when repeatedly opening and
closing the Jog input over a short period of time.
Added parameter 1410 [Jog Ramp Time], to allow you to set the rate of 3-29
acceleration and deceleration while the Jog function is active.
Changed option 3 "Quick Stop" to "Fast Stop" for parameters 354 [Aux Inp Flt Cfg] 3-53
and 365 [OverTemp Flt Cfg].
Changed option 35 “Fld Weak En” to “Force MinFld” for parameters 133-144 3-65
[Digital Inx Sel].
Added option 64 “Invert Flt” to parameters 133-144 [Digital Inx Sel], to allow a 3-65
digital input wired to an inverting fault device to issue an “Inverting Fault” (F37).
Updated the options for parameter 1391 [ContactorControl] to accommodate the 3-67
use of a AC or DC contactor with or without a dynamic brake resistor.
Added the new “Inverting Fault” (F37) fault to indicate that the associated inverting 4-5
fault device has opened.
Updated the following drive specifications: A-2
• Maximum short circuit rating
• Control speed regulation
• Torque regulation
Updated the fuses identified in the “Drive Power Circuit Protection” tables. A-7
Updated the “Control Power Circuit Protection Fuses” tables and fuse location A-15
illustrations.
Added the “Lug Kit Specifications” table. A-21
Added the instructions for operating the PowerFlex DC drive in field weakening C-5
mode and using a DC contactor and/or an inverting fault device in the armature
circuit with firmware version 1.006.
Updated the “Fine Tuning the Speed Regulator” procedure. C-29
Updated the terminal numbers indicated in the Digital Inputs/Outputs block D-3
diagram.
Updated the Ramp Reference block diagram to include the new parameter 1410 D-7
[Jog Ramp Time].
Removed the 20-COMM-L communication adapter from the compatible E-1
Communication Adapter Kits table.
PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

soc-ii
The information below summarizes the changes to the PowerFlex Digital

DC Drive User Manual, publication 20-UM001… since the initial release.
Change Page(s)
Removed erroneous derating information. 1-2, A-1
Updated AC Input Voltages tables. 1-15
Updated “AnalogCflct” Alarm description to include parameters 1323-1327 [DPI Px 4-7
Select].
Updated Agency Certification Information. A-1
Added notation regarding required installation in a Pollution Degree 2 environment. A-1
Updated the Maximum Short Circuit Ratings data. A-2
Added footnote regarding coil voltage to DC Loop Contactor table information. A-19
Updated block diagrams to correct parameter numbers and names. D-2

Table of Contents
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Summary of Manual Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . soc-i

Changes
Preface Overview
Who Should Use this Manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-1
What is in this Manual?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-1
Drive Storage Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-1
Drive Nameplate Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-2
Drive Frame Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-2
Reference Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-2
Manual Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-3
General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-3
Catalog Number Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-4
Chapter 1 Installation and Wiring

Mounting Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Operating Conditions and Temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Minimum Mounting Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Mounting Dimensions and Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Lifting PowerFlex DC Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Mounting Frame C Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Removing the Drive Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Frame A Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Frame B and C Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Line Reactors / Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Using Contactors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
AC Input Contactors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
DC Output Contactors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Dynamic Brake Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Control Power Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
General Grounding Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Safety Ground (PE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Power Feeder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Encoder Ground Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Tachometer Ground Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Power Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Cable and Wiring Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Power Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
AC Input Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
DC Output Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Typical Power Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Armature Converter Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
Field Circuit Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23
Field Current Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
Relay Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25
Thermistors and Thermal Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25
Control Circuit Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28
Frame C Heatsink Cooling Fans and Armature Fuse Signal Terminals . . . . . . . . . . . 1-31

2
I/O Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32

DIP Switch and Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32
I/O Signal and Control Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-35
I/O Wiring Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-37
Digital Encoder Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-40
DC Analog Tachometer Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-42
I/O and Control Wire Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-42
Chapter 2 Drive Start Up

Drive Start Up Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Before Applying Power to the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Applying Power to the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Speed-Up Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Configuring the Speed Zero Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Adaptive Speed Regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Chapter 3 Programming and Parameters

About Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
How Parameters are Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
File–Group–Parameter Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Numbered List View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Cross Reference Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Basic Parameter View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Advanced Parameter View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Monitor File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Motor Control File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Speed Command File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Dynamic Control File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
Applications File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
Utility File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-46
Communications File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-58
Input / Output File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-62
Parameter Cross Reference – by Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-72
Parameter Cross Reference – by Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-77
Chapter 4 Troubleshooting
Faults and Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Drive Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
HIM Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Manually Clearing Faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Fault Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Clearing Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Alarm Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Common Drive Symptoms and Corrective Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Drive will not start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Drive starts but motor does not turn and no armature current. . . . . . . . . . . . . . . . . . . 4-12
The motor does not reach commanded speed.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
The motor is turning in the wrong direction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
The motor reaches maximum speed immediately.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Testpoint Codes and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

3
Appendix A Supplemental Drive Information

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
IP20 (NEMA UL/Type Open) Watts Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Communication Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Typical Programmable Controller Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Logic Command/Status Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Drive Power Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Frame A and B Fuse Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Frame C Fuse Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
Control Power Circuit Protection Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-15
AC Input Line Reactors and AC Input Contactors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-17
DC Output Contactors and Dynamic Brake Resistor Kits . . . . . . . . . . . . . . . . . . . . . . . A-19
DC Contactor Crimp Lug Kit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-21
Appendix B HIM Overview

External and Internal Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
LCD Display Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
ALT Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Using the S.M.A.R.T. List Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Viewing and Editing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
LCD HIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
Removing/Installing the HIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
Appendix C Application Notes

Analog Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Example 1:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Example 2:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Analog Input Signal Comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Current / Speed Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
Droop Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Field Weakening Mode Configuration (v1.006) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Using a DC Contactor Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Using a DC Contactor and a Dynamic Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Using an Inverting Fault Device Only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6
Using a DC Contactor and an Inverting Fault Device. . . . . . . . . . . . . . . . . . . . . . . . . . C-7
Using a DC Contactor, a Dynamic Brake and an Inverting Fault Device . . . . . . . . . . . C-7
PID Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Configure a Line Speed Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9
Configure the Feedback Signal in the Follower Drive(s) . . . . . . . . . . . . . . . . . . . . . . C-10
Configure the Tension Set Point Signal in the Follower Drive(s) . . . . . . . . . . . . . . . . C-12
Reference Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-13
“Auto” Speed Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-13
“Manual” Speed Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-13
Changing Speed Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-13
Torque Reference Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-14
Auto/Manual Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-14
Speed Feedback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-15
Scale Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-16
Linking Parameters Via the Scale Block Parameters . . . . . . . . . . . . . . . . . . . . . . . . . C-17

4
Speed Regulation Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-17

Adaptive Speed Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-17
Speed Up Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-20
Speed Threshold Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-20
Speed Zero Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-22
Speed Draw Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-23
Start At Powerup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-24
Fine Tuning the Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-25
Manually Adjusting the Current Regulator Tune Settings. . . . . . . . . . . . . . . . . . . . . . C-26
Fine Tuning the Field Current Regulator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-26
Fine Tuning the Speed Regulator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-29
Fine Tuning the Voltage Regulator in the Field Converter . . . . . . . . . . . . . . . . . . . . . C-31
Tuning the Field Current Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-33
Appendix D Control Block Diagrams

Diagram Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Appendix E Installing a Communication Adapter

Communication Adapter Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
What The Communication Adapter Kit Includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
Tools That You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2
Installing the Communication Adapter Module in the Drive . . . . . . . . . . . . . . . . . . . . . . E-2
Appendix F Optional Analog and Digital I/O Expansion Circuit Board

What This Option Board Provides. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
I/O Expansion Board Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
Appendix G Optional 115V AC to 24V DC I/O Converter Circuit Board

What This Option Board Provides. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-1
I/O Converter Board Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-2
Index

Preface
Overview
The purpose of this manual is to provide you with the basic information
needed to install, start-up and troubleshoot the PowerFlex DC drive.
For information on . . . See page . . .
Who Should Use this Manual? Preface-1
What is in this Manual? Preface-1
Drive Storage Conditions Preface-1
Drive Nameplate Data Preface-2
Reference Materials Preface-2
Drive Frame Sizes Preface-2
Manual Conventions Preface-3
General Precautions Preface-3
Catalog Number Explanation Preface-4
Who Should Use this This manual is intended for qualified personnel. You must be able to
Manual? program and operate DC drives. In addition, you must have an
understanding of the parameter settings and functions detailed in this
manual.
What is in this Manual? The PowerFlex DC User Manual is designed to provide installation, basic
start-up information, and drive parameter definitions. For detailed drive
information, please refer to “Reference Materials” on page Preface-2 for a
list of additional publications.
Drive Storage Conditions If it is necessary to store the drive for any length of time before installation,
follow these storage guidelines in order to ensure satisfactory operation at
start up and to maintain warranty coverage:
• After receipt and inspection, repack the drive in its original shipping
container and store in a clean, dry place.
• Place where the ambient temperatures do not exceed -25° C (-13° F) or

+55° C (131° F)
• Place where the relative air humidity range does not exceed 5% - 95%.
• At an altitude of less than 3,000 meters (10,000 ft.) above sea level.

p-2 Overview
Drive Nameplate Data The PowerFlex DC drive contains a data nameplate located on the side of
each drive that identifies the specific model number design, applicable AC
input power and DC output power data. All communication with Rockwell
Automation personnel concerning this product should include this
information.
Cat No. 20P41AD4P1RA0NNN

UL Type OPEN/IP20
Series: A
I/O: 24VDC (Standard)
Input: 460VAC 50/60 Hz 3.3A 3 Phase Note: Certification
Original Firmware V. 1.001
LY
Marks Location.
Output: 500VDC 4.1A REGEN 1.0HP N223
C R
US
ON
1 Min Overload Amps 6.2 Listed
3 Sec Overload Amps 8.2
Ind. Cont.
Eq. 31KF Refer to the data
DC Field: nameplate label
E
Input: 460VAC 50/60 Hz 10A max. 1 Phase
PL
on your drive for
Output: 360VDC 10A max.
actual agency
AM
Regulator Power: 115/230VAC 50/60 Hz 1.0/0.5A 1 Phase certifications.
EX
MFD. in 2XXX on MMM DD Frame: A
Serial Number: A23E0042
Made in Italy
Drive Frame Sizes Similar PowerFlex DC drive sizes are grouped into frame sizes to simplify
spare parts ordering, dimensioning, etc. Refer to the Catalog Number
Explanation on page Preface-4 for a list of drive catalog numbers and their
respective frame sizes.
Reference Materials The following manuals are recommended for general drive information:
Title Publication Available Online at . . .
Preventive Maintenance of Industrial Control and DRIVES-TD001…
Drive System Equipment
Safety Guidelines for the Application, Installation SGI-1.1
and Maintenance of Solid State Control www.rockwellautomation.
com/literature
A Global Reference Guide for Reading Schematic 100-2.10
Diagrams
Guarding Against Electrostatic Damage 8000-4.5.2
For Allen-Bradley Drives Technical Support:

Title Online at . . .
Allen-Bradley Drives Technical Support www.ab.com/support/abdrives

Overview p-3
Manual Conventions • To help differentiate parameter names and LCD display text from other
text, the following conventions will be used:
– Parameter Names will appear in [brackets].

For example: [Armature Voltage].
– Display Text will appear in “quotes.” For example: “Enabled.”

• The following words are used throughout the manual to describe an
action:
Word Meaning
Can Possible, able to do something
Cannot Not possible, not able to do
something
May Permitted, allowed
Must Unavoidable, you must do this
Shall Required and necessary
Should Recommended
Should Not Not recommended
General Precautions
ATTENTION: This drive contains ESD (Electrostatic
! Discharge) sensitive parts and assemblies. Static control
precautions are required when installing, testing, servicing or
repairing this assembly. Component damage may result if ESD
control procedures are not followed. If you are not familiar with
static control procedures, reference A-B publication 8000-4.5.2,
“Guarding Against Electrostatic Damage” or any other applicable
ESD protection handbook.
ATTENTION: An incorrectly applied or installed drive can
! result in component damage or a reduction in product life. Wiring
or application errors, such as, undersizing the motor, incorrect or
inadequate AC supply, or excessive surrounding air temperatures
may result in malfunction of the system.
ATTENTION: Only qualified personnel familiar with DC drives
! and associated machinery should plan or implement the
installation, start-up and subsequent maintenance of the system.
Failure to comply may result in personal injury and/or equipment
damage.
ATTENTION: An incorrectly applied or installed bypass system
! can result in component damage or reduction in product life. The
most common causes are:
• Wiring AC line to drive output or control terminals.
• Improper bypass or output circuits not approved by
Allen-Bradley.
• Output circuits which do not connect directly to the motor.
Contact Allen-Bradley for assistance with application or wiring.

p-4 Overview
Catalog Number
Explanation
Position
1-3 4 5 6 7 8-10 11 12 13 14 15 16
20P 4 1 A D 4P1 R N 0 N N N
a b c d e f g h i j k l
a f1 g
Drive 230V, 60 Hz Input Field Supply
Code Type Armature Field Code Type
Code Hp Frame
Amps Amps A Three-Phase Regulated
20P PowerFlex DC
7P0 1.5 7 A 10 F Fixed Field w/Economy
9P0 2 9 A 10 R Single-Phase Regulated
b 012 3 12 A 10
Motor Operation 020 5 20 A 10
Code Type 029 7.5 29 A 10 h

038 10 38 A 10 Packaging/Documentation
2 Two Quadrant Operation
055 15 55 A 10 Code Shipping Carton User Manual
4 Four Quadrant Operation
073 20 73 A 14 0 No No
093 25 93 A 14 A Yes Yes
c 110 30 110 A 14 N Yes No
Input Type 146 40 146 B 20 Q No Yes
Code Type 180 50 180 B 20

1 6 Pulse 218 60 218 B 20
265 75 265 B 20
i
2 12 Pulse
HIM
360 100 360 B 20
Code Operator Interface
434 125 434 B 20
0 Blank Cover
d 521 150 521 C 20
Standard - for additional selections, refer to the
Enclosure PowerFlex Digital DC Drive Technical Data,
Conform. publication 20P-TD001. . .
Code Enclosure Rating f2
Coat
A IP20, NEMA/UL Type Open No 460V, 60 Hz Input
IP43, NEMA/UL Type 1 - Armature Field j
B No Code Hp Frame
Filter Amps Amps I/O Options
G IP54, NEMA/UL Type 12 No 4P1 2 4.1 A 10 Code Control
IP54, NEMA/UL Type 12 - 6P0 3 6 A 10 I/O Expansion Card (4 Additional 24V
H No
Fan/Filter 010 5 10 A 10 A dc Digital Inputs & Outputs, 2 Analog
N IP00, NEMA/UL Type Open No Outputs)
014 7.5 14 A 10
115V ac Conversion Card (8 Digital
019 10 19 A 10 B
Inputs & Outputs)
027 15 27 A 10
e I/O Expansion Card + 115V ac
035 20 35 A 10 C
Conversion
Input Voltage 045 25 45 A 10 None (8 - 24V dc Digital Inputs &
Code Voltage 052 30 52 A 10 N Outputs, 3 Analog Outputs and 2
B 230V ac 073 40 73 A 14 Analog Inputs are Standard)
C 400V ac 086 50 86 A 14
D 460V ac 100 60 100 A 14
E 600V ac
k
129 75 129 A 14
F 690V ac Communication Options
167 100 167 B 20
Code Description
207 125 207 B 20
N None
250 150 250 B 20
Standard - for additional selections, refer to the
330 200 330 B 20 PowerFlex Digital DC Drive Technical Data,
412 250 412 B 20 publication 20P-TD001. . .
495 300 495 C 20
667 400 667 C 20
l
Cabinet Options
Code Type
N None

Chapter 1
Installation and Wiring
This chapter provides information on mounting and wiring the PowerFlex

DC drive.
For information on . . See page For information on. . See page
Mounting Considerations 1-2 Control Power Protection 1-11
Mounting Dimensions and Weights 1-3 General Grounding Requirements 1-12
Lifting PowerFlex DC Drives 1-5 Power Circuit Protection 1-13
Removing the Drive Covers 1-7 Cable and Wiring Recommendations 1-14
Line Reactors / Filters 1-9 Power Wiring 1-15
Using Contactors 1-9 I/O Wiring 1-32
Most start-up difficulties are the result of incorrect wiring. Every precaution
must be taken to assure that the wiring is done as instructed. All items must
be read and understood before the actual installation begins.
Important: The PowerFlex DC drive is not designed for use with multiple
motor applications.
ATTENTION: The following information is merely a guide for

! proper installation. Rockwell Automation cannot assume
responsibility for the compliance or the noncompliance to any
code, national, local or otherwise for the proper installation of this
drive or associated equipment. A hazard of personal injury and/or
equipment damage exists if codes are ignored during installation.

1-2 Installation and Wiring
Mounting Considerations Operating Conditions and Temperatures

PowerFlex DC drives are designed to operate at 0° to 50° C surrounding air
temperature without derating. The drive must be mounted in a clean, dry
location. Contaminants such as oils, corrosive vapors and abrasive debris
must be kept out of the enclosure. NEMA/UL Type Open, IP20 enclosures
are intended for indoor use primarily to provide a degree of protection
against contact with enclosed equipment. These enclosures offer no
protection against airborne contaminants.
Minimum Mounting Clearances

Minimum clearance requirements (indicated in Figure 1.1) are intended to
be from drive to drive. Other objects can occupy this space; however,
reduced airflow may cause protection circuits to fault the drive. The drive
must be mounted in a vertical orientation as shown below and must not be
mounted at an angle greater than 30° from vertical. In addition, inlet air
temperature must not exceed the product specification.
Figure 1.1 Drive Enclosure Minimum Mounting Clearances
150 mm (6.0 in.)
150 mm (6.0 in.)

PORT
MOD
NET A
NET B
PORT
MOD
NET A STS
NET B
STS
10 mm 10 mm 10 mm 50 mm Airflow through
(0.4 in.) (0.4 in.) 150 mm (6.0 in.) (0.4 in.) (2.0 in.) the drive must
not be impeded.

Installation and Wiring 1-3
Mounting Dimensions and The PowerFlex DC drive is available in a NEMA/UL Type Open, IP20
Weights enclosure. Following all mounting instructions in order to ensure proper
operation.
ATTENTION: Remove all loose packing materials, including

! the container(s) of desiccants (if any), from the drive enclosure
before mounting and energizing the drive.
Figure 1.2 Frame A Approximate Dimensions

A B C A1 B1
mm (in.) mm (in.) mm (in.) mm (in.) mm (in.)
267 (10.5) 359 (14.0) 287 (11.3) 250 (9.8) 275 (10.8)
A C
PORT
MOD
NET A
NET B
STS
B B1
A1
Table 1.A Frame A Weights

Weight
Drive Current Rating Code Drive Drive & Packaging
230V 460V kg (lbs.) kg (lbs.)
7P0 4P1 8.4 (19.5) 10.5 (23.1)
9P0 6P0
012 010
020 014
– 019
029 027
038 035 8.8 (19.4) 11 (24.3)
055 045
– 052
073 073 10.8 (23.8) 13 (28.7)
093 086
110 100
– 129

Figure 1.3 Frame B Approximate Dimensions

A A1 A2 B B1 C
mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) mm (in.)
311 (12.2) 275 (10.8) 16.5 (0.65) 388 (15.3) 375 (14.8) 350 (13.8)
A C
A1
PORT
MOD
NET A
NET B
STS
B1 B
A2
Table 1.B Frame B Weights

Weight
Drive w/ND Rating Code Drive Drive & Packaging
230V 460V kg (lbs.) kg (lbs.)
146 167 25.5 (56.2) 27.5 (60.6)
180 207
218 –
265 250 29.5 (65.0) 31.5 (69.4)
360 330 32 (70.5) 34 (75)
434 412

Figure 1.4 Frame C Approximate Dimensions

A A1 B B1 B2 B3 B4 C
mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) mm (in.)
521 (20.5) 499 (19.7) 511 (20.1) 400 (15.7) 200 (7.9) 55 (2.2) 56 (2.2) 416 (16.4)
A1 C
B4
PORT
MOD
NET A
NET B
B1 STS
B2
B3
Table 1.C Frame C Weights

Weight - Regenerative Drives Weight - Non-regenerative Drives
Drive w/ND Rating Code Drive Drive & Packaging Drive Drive & Packaging
230V 460V kg (lbs.) kg (lbs.) kg (lbs.) kg (lbs.)
– 495 61 (134.5) 74 (163.1) 57 (125.7) 70 (154.3)
521 667 65 (143.3) 81 (178.6) 62 (136.7) 75 (165.3)
Lifting PowerFlex DC Drives The dimensions and weights specified above must be taken into
consideration when mounting the device. Use the proper equipment to
safely lift and hold the weight of the drive while mounting.
ATTENTION: To guard against possible personal injury or

! equipment damage . . .
• Inspect all lifting hardware for proper attachment before lifting

the drive.
• Do Not allow any part of the drive or lifting mechanism to
make contact with electrically charged conductors or
components.
• Do Not subject the drive to high rates of acceleration or
deceleration while transporting to the mounting location or
when lifting.
• Do Not allow personnel or their limbs directly underneath the
drive when it is being lifted and mounted.

Mounting Frame C Drives

All lifting equipment and lifting components (hooks, bolts, lifts, slings,
chains, etc.) must have a minimum lifting capacity of 453.6 kg (1,000 lb.).
Important: Verify that all mounting screws are properly tightened before
and after drive operation.
1. Verify the hole pattern on the panel to which the drive will be mounted.
Refer to Figure 1.4 on page 1-5.
2. Insert, but do not tighten, one bolt in one of the top holes in the panel.
The bolt must be fully threaded into the panel before hanging the drive.
3. Insert the properly sized and rated lifting hooks into the holes on the
lifting flanges at the top of the drive. To limit the pull in forces on the
drive, the lifting devices connected to the hooks must be long enough to
make the angle between the chain or cable and a vertical line extending
up from the flange center less than 45 degrees as illustrated below.
Figure 1.5 Lifting Angle
Angle Must Be Less

Than 45 Degrees
Lifting flange
4. Lift the drive into place on to the bolt installed in the panel.
5. Install the remaining five bolts into the panel. Tighten all bolts to a
torque of 22.6 N•m (200 lb•in).

Removing the Drive Covers The lower protective cover must be removed in order to access the drive’s
power and I/O terminals. The upper cover only needs to be removed to
install an optional communication adapter and service the drive. (Refer to
Installing a Communication Adapter on page E-1 for information.)
Frame A Drives
You must remove both the lower protective cover and the power terminal
cover on frame A drives to access the power terminals.
Remove the Power Terminal Cover
Remove the two screws as shown below and slide the cover down and off
the chassis.
Figure 1.6 Frame A Power Terminal Cover Removal

Remove the Lower Protective Cover

Remove the two screws as shown below and, while gently lifting along the
top edge, slide the cover down and off the chassis.
Figure 1.7 Frame A Lower Cover Removal
PORT
MOD
NET A
NET B
STS
Frame B and C Drives

Loosen, but do not remove, the two screws that secure the bottom cover.
Then, slide the cover down until the screw heads line up with the key holes
and lift the cover off the chassis.
Figure 1.8 Frame B & C Drive Cover Removal
Frame B Shown

Line Reactors / Filters When connecting the drive directly to the main distribution system an AC
line reactor must be used to guard against system disturbance. The type of
line reactor used depends upon the following:
• the current absorbed by the AC input

• the AC input voltage
• the relative short circuit voltage
• the AC input frequency
Refer to AC Input Line Reactors and AC Input Contactors on page A-17 for
a list of recommended AC line reactors.
Using Contactors When using an AC input contactor, the IEC AC1 rating of the contactor
must be equal to the rated thermal (RMS) current value at the mains input of
the drive.
Drive configurations for AC or DC contactors, with or without a dynamic

brake, are as follows (refer to Typical Power Wiring Diagrams on page 1-17
for wiring examples):
• When only an AC contactor is used:
❏ Set parameter 1391 [ContactorControl] to 1 “AC Cntctr” (default

value) (1)
❏ Set one [Relay Out x Sel] parameter and one [Digital Inx Sel]
parameter to “Contactor” (default value for parameters 1392 [Relay
Out 1 Sel] and 140 [Digital In8 Sel])
• When only a DC contactor is used:
❏ Set parameter 1391 [ContactorControl] to 3 “DC Cntctr” (1)
❏ Set one [Relay Out x Sel] parameter and one [Digital Inx Sel] to
“Contactor” (default value for parameters 1392 [Relay Out 1 Sel]
and 140 [Digital In8 Sel])
• When an AC contactor and dynamic brake contactor are used:
❏ Set parameter 1391 [ContactorControl] to “AC Cntctr+DB” (1)
❏ Set one [Relay Out x Sel] parameter (1392 [Relay Out 1 Sel] or 629
[Relay Out 2 Sel]) to “Contactor” and the other relay output to
“ContactorDB”
❏ Set one [Digital Inx Sel] parameter to “Contactor” (default value

for parameter 140 [Digital In8 Sel])
(1)
Par 1391 [ContactorControl] is contained in the “Advanced” parameter configuration group. Refer to How
Parameters are Organized on page 3-3 for more information.

• When a DC contactor and dynamic brake contactor are used:
❏ Set parameter 1391 [ContactorControl] to “DC Cntctr+DB” (1)

❏ Set one [Relay Out x Sel] parameter (1392 [Relay Out 1 Sel] or 629
[Relay Out 2 Sel]) to “Contactor” and the other relay output to
“ContactorDB”
❏ Set one [Digital Inx Sel] parameter to “Contactor” (default value

for parameter 140 [Digital In8 Sel])
• When a contactor is NOT used:

❏ Set parameter 1391 [ContactorControl] to “None” (1)
❏ Do NOT set either [Relay Out x Sel] parameter to “Contactor” or

“ContactorDB”
❏ Do NOT set any [Digital Inx Sel] parameter to “Contactor”
When operating a drive with firmware version 1.006 in field weakening

mode with a DC contactor and/or inverting fault device installed in the
armature circuit, refer to Field Weakening Mode Configuration (v1.006) on
page C-5.
AC Input Contactors
Refer to AC Input Line Reactors and AC Input Contactors on page A-17 for
a list of recommended AC input contactors.
DC Output Contactors
A DC output contactor can be used to connect the output of the armature
circuit to the DC motor. If a DC output contactor is used, an AC input
contactor is not needed.
Refer to DC Output Contactors and Dynamic Brake Resistor Kits on

page A-19 for a list of recommended DC output contactors.
Dynamic Brake Resistors

Refer to DC Output Contactors and Dynamic Brake Resistor Kits on
page A-19 for a list of recommended dynamic brake resistor kits.
(1)
Par 1391 [ContactorControl] is contained in the “Advanced” parameter configuration group. Refer to How
Parameters are Organized on page 3-3 for more information.

Control Power Protection The 115V / 230V AC control circuit power input terminals U2 and V2 are
required to be short circuit protected. This protection can be provided by
using standard time delay fuses or a circuit breaker.
The time delay fuses or circuit breaker must be selected to survive the short
circuit available current of the feeder source for this circuit and the inrush
current of the drive’s power supply.
The rating of the fuses or circuit breaker should be sized mainly to protect
the wiring from the fuses/circuit breaker connections to terminals U2 and
V2, and not nuisance trip or blow from the inrush current.
The table below lists the input current characteristics of the control power.
Table 1.D Control Power Protection
Drive Current Control Power Supply
Rating Code(1) Rated input current Inrush input current
Frame 230V 460V Board ID Power 115V 230V 115V 230V
7P0 4P1
A through through SW1-31 60 W 1A 0.5 A 20 A 10 A
110 129
146 167
B&C through through SW2-32 110 W 1.2 A 0.7 A 15 A 7.5 A
521 667
(1)
Refer to Catalog Number Explanation on page Preface-4, positions 8-10 for corresponding drive HP rating,
armature amp rating and field amp rating.
Control power input should be supplied by a power source that is stabilized

and buffered from the power system transients. The control power of many
drives can be fed from a single source, as long as proper distribution
protection is provided.

General Grounding The drive Safety Ground - PE must be connected to system ground.
Requirements Ground impedance must conform to the requirements of national and local
industrial safety regulations and/or electrical codes. The integrity of all
ground connections should be periodically checked.
For installations within a cabinet, a single safety ground point or ground bus
bar connected directly to building steel should be used. All circuits
including the AC input ground conductor should be grounded
independently and directly to this point/bar.
ATTENTION: In order to comply with the essential

! requirements of the CE Low Voltage Directive 2006/95/EC,
PowerFlex DC drives may not be powered from a corner-earthed
(TN with one phase earthed) supply system. Although
PowerFlex DC drives are compliant with the requirements of the
CE Low Voltage Directive when powered from an IT or
impedance-earthed supply system, power must be removed from
the drive as soon as possible after an earth fault is detected in the
power system to satisfy CE safety requirements related to the
insulation system of the drive.
Figure 1.9 Typical Grounding
PORT
MOD
NET A
NET B
STS
PE1/
W
U
C
D
V
AC Line
Reactor
Earth
AC Mains Supply
L1
L2
L3 All wires (including motor

ground) must be connected
Safety
Transformer inside the motor terminal box.
Ground
Safety Ground (PE)

This is the safety ground for the drive that is required by code. This point
must be connected to adjacent building steel (girder, joist), a floor ground
rod or bus bar (see above). Grounding points must comply with national and
local industrial safety regulations and/or electrical codes.

Power Feeder
Each power feeder from the substation transformer to the drive must be
provided with properly sized ground cables. The conduit or cable armor
should be bonded to the substation ground at both ends. Each transformer
enclosure and/or frame must be bonded to ground at a minimum of two
locations.
Encoder Ground Connections

If used, must be routed in grounded steel conduit. The conduit must be
grounded at both ends. The encoder cable shield must be connected to the
shield ground on the drive side. Do not connect the encoder cable shield to
ground on the motor side.
Tachometer Ground Connections

If used, ground connections must be routed in grounded steel conduit. The
conduit must be grounded at both ends. Ground the cable shield at the drive
end only using the shield clamps on the grounded metal plate supporting the
control board (refer to I/O Terminal Block Locations on page 1-36 for
shield clamp location).
Power Circuit Protection It is recommended that you install the PowerFlex DC drive with fast acting
fuses to protect the armature converter on the AC input and DC output (for
four quadrant drives only) sides. Internally mounted fuses for armature
converter protection are provided with 230V, 521A and 460V, 495A and
667A frame C PowerFlex DC drives. Refer to Drive Power Circuit
Protection on page A-7 for a list of replacement fuses and general fuse
locations.

Cable and Wiring Use the following cable and spacing recommendations for all drives sizes:
Recommendations
Minimum Spacing Between Classes
Steel Conduit/Tray
See Spacing
Wiring Notes,
Category Class Signal Definition Signal Example Cable Type 1 2/3/4 5/6 7/8 9/10/11 page 1-15
Power 1 AC Power (600V 2.3kV 3/ph AC Lines Per NEC & 0 3/9 in. 3/9 in. 3/18 in. See Note 6 1/2/5
Or Greater) Local Codes (76/229 mm) (76/229 mm) (76/457 mm)
2 AC Power (Less 460V 3/ph AC Lines 3/9 in. 0 3/6 in. 3/12 in. See Note 6 1/2/5
Than 600V) (76/229 mm) (76/152 mm) (76/305 mm)
3 DC Power DC Motor Armature
4 DC Power DC Motor Field
Control 5 115V AC/DC Relay Logic/PLC I/O 3/9 in. 3/6 in. 0 3/9 in. See Note 6 1/2/5
Logic Motor Thermostat (76/229 mm) (76/152 mm) (76/229 mm)
115V AC Power Power Supplies,
Instruments
6 24V AC/DC Logic PLC I/O
Signal 7 Analog Signals, Reference/feedback Shielded Cable 3/18 in. 3/12 in. 3/9 in. 0 1/3 in. 2/3/4/5
(Process) DC Supplies Signal, 5 To 24V DC – Belden 8735, (76/457 mm) (76/305 mm) (76/229 mm) (25/76 mm)
Digital (Low TTL 8737, 8404
Speed)
8 Digital (High I/O, Encoder, Count Shielded Cable
Speed) Pulse Tach – Belden 9728,
9730
Signal 9 Serial RS-232 Shielded Cable See Note 6 1/3 in. 0 –
(Comm.) Communication (20-COMM-R), 422 – Belden (25/76 mm)
To Terminals/ RS-232 –
printers 8735, 8737
RS-422 –
9729, 9730
11 Serial PLC Remote I/O, Twinaxial
Communication PLC Data Highway Cable –
(Greater Than Belden 9463,
20k Baud) A-B 1770-CD
Example:
Spacing relationship between 480V AC incoming power leads and 24V DC

logic leads:
• 480V AC leads are Class 2; 24V DC leads are Class 6
• For separate steel conduits, the conduits must be 3 inches (76 mm) apart
• In a cable tray, the two groups of leads are to be 6 inches (152 mm) apart
Minimum Spacing Between Classes

Steel Conduit/Tray
Wiring
Category Class Signal Definition Signal Example 1 2/3/4 5/6
Power 2 AC Power (less 460V 3/Ph AC 3/6 in.
than 600V) Lines (76/152 mm)
Control 6 24V AC/DC PLC I/O 3/6 in.
Logic (76/152 mm)
Note: Cells removed from example table for clarity only.

Spacing Notes:
1. Both outgoing and return current carrying conductors are to be pulled in same conduit or laid adjacent in
tray.
2. Cables of the following classes can be grouped together.
A. Class 1; Equal to or above 601 volts.
B. Classes 2, 3 and 4 may have their respective circuits pulled in the same conduit or layered in the same
tray.
C. Classes 5 and 6 may have their respective circuits pulled in the same conduit or layered in the same
tray. Note: Bundle may not exceed conditions of NEC 310.
D. Classes 7 and 8 may have their respective circuits pulled in the same conduit or layered in the same
tray. Note: Encoder cables run in a bundle may experience some amount of EMI coupling. The circuit
application may dictate separate spacing.
E. Classes 9, 10 and 11 may have their respective circuits pulled in the same conduit or layered in the
same tray. Communication cables run in a bundle may experience some amount of EMI coupling and
corresponding communication faults. The application may dictate separate spacing.
3. All wires of class 7 through 11 MUST be shielded per the recommendations.
4. In cable trays, steel separators are advisable between the class groupings.
5. If conduit is used, it must be continuous and composed of magnetic steel.
6. Spacing of communication cables classes 2 through 6 is:
CONDUIT SPACING: THROUGH AIR:
115 Volts – 1 in. (25 mm) 115 Volts – 2 in. (51 mm)
230 Volts – 1.5 in. (38 mm) 230 Volts – 4 in. (101.5 mm)
380/575 Volts – 3 in. (76 mm) 380/575 Volts – 8 in. (203 mm)
575 volts – proportional to 6 in. (152 mm) per 575 volts – proportional to 12 in. (305 mm) per 1000
1000 volts. volts.
Power Wiring AC Input Voltages

PowerFlex DC drives are rated for the following AC input voltages:
Armature Circuit Field Circuit Control Circuit
Terminals U, V, W Terminals U1, V1 Terminals U2, V2
230V ±10 %, 3Ph 230V ±10 %, 1Ph 115V ±15 %, 1 Ph(1)
400V ±10 %, 3Ph 400V ±10 %, 1Ph or
440V ±10 %, 3Ph 460V ±10 %, 1Ph 230V ±15 %, 1Ph
460V ±10 %, 3Ph @ 50/60 Hz ±5 % @ 50/60 Hz ±5 %
480V ±10 %, 3Ph
@ 50/60 Hz ±5 %
(1) For frame B and C drives only, a jumper must be placed between terminals SA-SB on the Switching Power
Supply circuit board for the control circuits to work with 115V AC input. Refer to Figure 1.26 on page 1-29 for
terminal block location on frame B drives and Figure 1.27 on page 1-30 for terminal block location on frame C
drives.

DC Output Voltages
The output voltages below take into account an AC input undervoltage
within the stated tolerance limits and a voltage drop of 4% due to an AC
input line reactor. It is the same as the rated armature voltage suggested for
the connected motor.
Armature Circuit
AC Input Voltage DC Output Armature Voltage (Terminals C & D)
(Terminals U, V, W) Two Quadrant Drive Four Quadrant Drive
230V ±10 %, 3Ph 260V 240V
400V ±10 %, 3Ph 470V 420V
440V ±10 %, 3Ph 530V 460V
460V ±10 %, 3Ph 560V 480V
480V ±10 %, 3Ph 580V 500V
Field Circuit
AC Input Voltage DC Output Field Voltage(1) (Terminals C1 & D1)
(Terminals U1 & V1) Fixed Field Adjustable Field
230V ±15 %, 1Ph 200V 200V
400V ±15 %, 1Ph 310V 310V
460V ±10%, 1Ph 360V 360V
(1)
The max field voltage is equal to 0.85 x AC input line voltage

Typical Power Wiring Diagrams

Figure 1.10 - Figure 1.13 represent recommended power wiring
configurations.
Figure 1.10 Power Wiring with AC Input Contactor
(1)
34 (on I/O TB4) (2)
FU1
(N.O. Relay) C
M1 AC Contactor
Aux 19 (+24V - on I/O TB2)
13 14
FU3 A1
L1 T1
L1 U
FU4
L2 T2
L2
FU5
V
M
L3 T3
3 Phase AC line L3 W
A1 A2 A2
FU8 FU9
PowerFlex DC (2)
FU2
Drive D
Control
U2 Board P/S
460V 115V V2
(3) Control Power /
35 Relay Terminal
(3)
36 Block
FU6
F1
U1 C1
FU7 Field Power
V1 Terminal Block D1
F2
(1)
Par 140 [Digital In8 Sel] set to 31 “Contactor”
(2) Armature output fuses are required on four quadrant and are recommended on two quadrant Frame A and B drives. Fuses with Trip Indicator
Switches are recommended for Inverting Fault protection when the motor will be Field Weakened and run above base speed. Refer to Figure 1.13 on
page 1-19.
(3)
Par 1391 [ContactorControl] = 1 “AC Cntctr” and Par 1392 [Relay Out 1 Sel] = 25 “Contactor”. Important: Terminal 35 and 36 are on the Control
Power / Relay Terminal block, NOT the I/O terminal blocks. See Figure 1.20 through Figure 1.22.

Figure 1.11 Power Wiring with DC Output Contactor
(1)
34 (on I/O TB4)
(N.O. Relay)
M1 DC Contactor
Aux
19 (+24V on I/O TB2) 13 14
(2)
FU1
FU3 L1 T1
C
L1 U
FU4 L2 T2
D
L2 V
FU5 A1 A2
A1
PowerFlex DC
FU8 FU9 Drive M
A2
Control (2)
U2 Board P/S FU2
460V 115V V2
(3) Control Power /
35 Relay Terminal
(3)
36 Block
FU6
F1
U1 C1
FU7 Field Power
F2
(1) Par 140 [Digital In8 Sel] set to 31 “Contactor”
(2)
Armature output fuses are required on four quadrant and are recommended on two quadrant Frame A and B drives. Fuses with Trip Indicator
page 1-19.
(3) Par 1391 [ContactorControl] = 3 “DC Cntctr” and Par 1392 [Relay Out 1 Sel] = 25 “Contactor”. Important: Terminal 35 and 36 are on the Control
Power / Relay Terminal block, NOT the I/O terminal blocks. See Figure 1.20 through Figure 1.22.

Figure 1.12 Power Wiring with DC Output Contactor and a Dynamic Brake
(1)
34 (on I/O TB4)
(N.O. Relay)
M1 DC Contactor
Aux
19 (+24V on I/O TB2) 13 14
FU3 L1 T1
C
L1 U
FU4 L2 T2
D FU1
(2)
L2 V
A1 A2 A1 L2 L1 13
FU5
Aux
PowerFlex DC A2 T2 T1 14 A1
FU8 FU9 Drive (N.C. Relay)

DB Contactor M
Control
V2 Board P/S DB A2
460V 115V U2 Resistor
(2)
(3) FU2
35
(3) Control Power /
36 Relay Terminal
(3) Block
75
(3)
76
FU6
F1
U1 C1
FU7 Field Power
F2
(1) Par 140 [Digital In8 Sel] set to 31 “Contactor”
(2)
Armature output fuses are required on four quadrant and are recommended on two quadrant Frame A and B drives. Fuses with Trip Indicator
page 1-19.
(3)
Par 1391 [ContactorControl] = 4 “DC Cntctr+DB”, Par 1392 [Relay Out 1 Sel] = 25 “Contactor”, and Par 629 [Relay Out 2 Sel] = 24 “ContactorDB”.
Important: Terminal 35, 36, 75 and 76 are on the Control Power / Relay Terminal block, NOT the I/O terminal blocks. See Figure 1.20 through Figure
1.22.
Figure 1.13 Power Wiring with Armature Output Fuses and Inverting Fault Status
(1)
FU1
A1
PowerFlex DC M
Drive (1)
A2
FU2
(2)
33 (on I/O TB4)
(1)
Armature output fuses are required on four quadrant and are recommended
on two quadrant Frame A and B drives. Fuses with Trip Indicator Switches are
19 (+24V on I/O TB2) recommended for Inverting Fault protection when the motor will be Field
Weakened and run above base speed.
(2) Par 139 [Digital In7 Sel] set to 64 “Invert Flt”.

Armature Converter Connections

Terminals Description
U, V, W Three phase AC input to the armature converter
C, D DC output to the motor armature
PE Safety ground
Figure 1.14 Frame A Armature Converter Terminal Block Location
Front View
Note: Front view of drive shown with bottom protective and power terminal covers removed.
Refer to Removing the Drive Covers on page 1-7 for information on removing the drive covers.
PE U C V D W
ATTENTION: Do not operate the drive with the power

! terminal cover removed. Operating the drive with the power
terminal cover removed may result in a hazardous condition that
could cause personal injury and/or equipment damage.
Figure 1.15 Frame B Armature Converter Terminal Block Location
PE U C V D W

Figure 1.16 Frame C Armature Converter Terminal Block Location
Front View
PE U C V D W
Bottom View

Table 1.E Armature and Safety Ground (PE) Terminal Specifications

Drive Current
Frame
Rating Code(1) Terminal Bolt Tightening Torque
230V 460V Terminals Wire Size and Type Size (mm) (N•m / lbs•in)
A 7P0 4P1
9P0 6P0
012 010
020 014
– 019 U, V, W, C, D, PE 5 6 / 53
029 027
038 035
055 045
– 052
073 073
093 086
110 – U, V, W, C, D, PE Terminal Block 12 / 106
– 100
– 129
B 146 167 U, V, W, C, D 10 50 / 442.5
PE 8 25 / 221
180 – U, V, W, C, D 10 50 / 442.5
PE 8 25 / 221
218 207 U, V, W, C, D See Cable and Wiring 10 50 / 442.5
Recommendations on
PE page 1-14 8 25 / 221
265 250 U, V, W
10 50 / 442.5
C, D
PE 8 25 / 221
– 330 U, V, W
10 50 / 442.5
C, D
PE 8 25 / 221
360 412 U, V, W
10 50 / 442.5
C, D
PE 8 25 / 221
434 – U, V, W
10 50 / 442.5
C, D
PE 8 25 / 221
C 521 495 U, V, W
10 50 / 442.5
C, D
PE 8 25 / 221
– 667 U, V, W
10 50 / 442.5
C, D
PE 8 25 / 221
(1)
See to Catalog Number Explanation on page Preface-4, positions 8-10 for corresponding drive HP rating,

Field Circuit Connections

U1, V1 Single phase AC input to the field circuit
C1, D1 DC output to the motor field
Figure 1.17 Frame A Field Circuit Terminal Block Location
U1
V1
C1
D1
Bottom of Drive
Figure 1.18 Frame B Field Circuit Terminal Block Location
U1
V1
C1
D1
Top of drive

Figure 1.19 Frame C Field Circuit Terminal Block Location
Front of drive
D1 C1 U1 V1
Table 1.F Field Circuit Wire Sizes and Terminal Specifications

Drive Current Rating
Code(1) Tightening Torque
Frame 230V 460V Terminals Wire Size and Type(2) (N•m / lbs•in)
All All All U1, V1, C1, D1 24-10 AWG/kcmils 0.5 - 0.8 / 4.4 - 7.1
(1)
(2)
See Cable and Wiring Recommendations on page 1-14 for more information.
Field Current Resistors

The drive’s control circuit board is factory set to the minimum field current
rating based on the drive size. The setting of DIP switch S14 must be
changed to be ≥ the rated field current specified on the motor nameplate or
possible motor damage may result. In addition, the value selected with
switch S14 must be entered in parameter 374 [Drv Fld Brdg Cur] in the
control software when the drive is commissioned (refer to Drive Start Up on
page 2-1.)
ATTENTION: DIP switch S14 must be set to be ≥ the rated

! field current specified on the motor nameplate or possible motor
damage may result.

Compare the field current value of the motor to the rated value of the
internal field converter of the drive (see Table 1.G below) and set switch
S14 to the closest value.
Note: The configuration of switch S14 is not required if the motor’s field
control is provided via an external source, however, in this case it is
recommended that the switch settings be completed as described above.
Table 1.G DIP Switch S14 Field Current Configuration Settings
ON DIP Note: Illustration is an example

configuration only. DIP switch S14 must be
set ≥ the rated field current specified on
the motor nameplate or possible motor
1 2 3 4 5 6 7 8
damage may result.
Equivalent
Switch ohms 148 330 182 36.4 845 1650 Resistance
Field current
scale S14-1 S14-2 S14-3 S14-4 S14-5 S14-6 S14-7 S14-8
1.0 A OFF OFF OFF OFF OFF ON 1650 ohm
2.0 A OFF OFF OFF OFF ON OFF 845 ohm
3.0 A OFF OFF OFF OFF ON ON 558.8 ohm
5.0 A OFF ON OFF OFF OFF OFF 330 ohm
10.0 A ON OFF OFF OFF OFF OFF Not used 168 ohm
12.9 A ON OFF OFF OFF ON ON 129.2 ohm
17.2 A OFF ON ON OFF ON ON 97 ohm
20.0 A ON OFF ON OFF OFF ON 83 ohm
24.1 A ON ON ON OFF OFF OFF 69 ohm
Relay Outputs
Maximum Maximum
Terminals Description Voltage Current
35, 36 Normally open contact. Configured with parameter 1392 [Relay
Out 1 Sel] - set to 25 “Contactor” by default.
75, 76 Normally open contact. Configured with parameter 629 [Relay 250V AC 1A
Out 2 Sel] - set to 5 “Ready” by default.
78, 79 Motor thermistor connections (PTC)
Terminals 35 and 36 and 75 and 76 are N.O. relay outputs. The relay output
between terminals 35 and 36 is configured with parameter 1392 [Relay Out
1 Sel]. The relay output between terminals 75 and 76 is configured with
parameter 629 [Relay Out 2 Sel]. See Using Contactors on page 1-9 for
more information.
Thermistors and Thermal Switches

To detect motor overheating and protect the motor from overloading, an
external, user-supplied thermistor (PTC) or thermal switch must be
connected to terminals 78 and 79. The drive’s response to a motor over
temperature fault is configured in parameter 365 [OverTemp Flt Cfg]. If a
temperature sensor is not used, a 1k ohm resistor must be connected

between terminals 78 and 79 (installed at the factory). Follow the

appropriate instructions below when installing a thermal sensor.
Thermistors (PTC)
PTC thermistors fitted in the motor can be connected directly to the drive
via terminals 78 and 79. In this case the 1k ohm resistor is not required
between terminals 78 and 79.
Thermal Switches (Klixon®) in the Motor Windings
“Klixon” type temperature-dependent contacts can disconnect the drive

from the motor via an external control or can be configured as an external
fault using a digital input on drive. They can also be connected to terminals
78 and 79 in order to indicate a drive “Motor Over Temp” fault (F16),
though this is not recommended due to the noise sensitivity of the current
threshold circuitry. If a thermal switch is used a 1k ohm resistor must be
placed in series between the switch and one of the terminals.
Table 1.H Relay Outputs and Thermistor/Thermal Switch Wire Sizes and
Specifications
Wire Size and Type(1) Tightening
Flexible Multi-core Torque
Signal Type Terminals (mm2) (mm2) AWG N•m (lb•in)
Relay Outputs 35 & 36, 75 & 76
Thermistor and 78 & 79 0.140 - 1.500 0.140 - 1.500 26-14 0.5 (4.4)
Thermal Switches
(1)
Figure 1.20 Frame A Relay and Thermistor/Thermal Switch Terminal Block Locations
Note: Terminals 78 and 79

shown with 1k ohm resistor in 78 79 35 36 75 76
place of temperature sensor.

Figure 1.21 Frame B Relay and Thermistor/Thermal Switch Terminal Block Locations
78 79 35 36 75 76
Figure 1.22 Frame C Relay and Thermistor/Thermal Switch Terminal Block Locations
35 36 75 76 78 79

Control Circuit Input Power

U2, V2 Single phase AC power for the control circuits
The control circuit must be powered by an external 230V AC or 115V AC

single phase power supply. For frame B and C drives only, a jumper is
required between terminals SA and SB for 115V AC control input power.
For frame B drive SA-SB terminal block location, refer to Figure 1.26 on
page 1-29. For frame C drive SA-SB terminal block location, refer to Figure
1.27 on page 1-30.
Figure 1.23 Frame A Control Circuit Terminal Block Location
U2 V2
Figure 1.24 Frame B Control Circuit Terminal Block Location
U2 V2

Figure 1.25 Frame C Control Circuit Terminal Block Location
U2 V2
Table 1.I Control Circuit Wire Sizes and Terminal Specifications

Code(1) Wire Size and Type(2)
Frame
Flexible Multi-core Tightening Torque

230V 460V Terminals (mm2) (mm2) AWG (N•m / lbs•in)
All All All U2, V2 0.14 - 1.5 0.14 - 2.5 26 - 14 0.5 / 4.4
(1)
(2) See Cable and Wiring Recommendations on page 1-14 for more information.
Figure 1.26 SA-SB Terminal Block Location on Frame B Drives
The SA-SB
terminal block is
located at the top
of the drive.
Front of drive

Figure 1.27 SA-SB Terminal Block Location on Frame C Drives

The SA-SB terminal block is located on the Switching Power Supply circuit board on the back
of the Control EMI Shield.
Switching Power Supply board SA-SB terminals Back of Control EMI shield
XSW connector
To access the SA-SB terminal block:
1. Remove the top protective cover from the drive. 2. Disconnect cables XFCD and XR.
3. Loosen 3. Loosen
captive captive
screws. screws.
4. Lower EMI
shield and
disconnect
cable XSW
from Switching
Power Supply
board (see
above).

Frame C Heatsink Cooling Fans and Armature Fuse Signal Terminals

Frame C drives require an external power supply for the heatsink cooling
fans and include internal armature circuit protection fuses (drives rated
521A @ 230V AC and 495A and 667A @ 460V AC input only). The
terminals for the internal armature circuit protection fuses can be connected
to an external device to provide indication that the fuses have opened.
Table 1.J Heatsink Cooling Fans and Fuse Signal Terminal Designations
Terminal Description Maximum Voltage Maximum Current
U3
Single-phase AC input power for cooling fans. 230V AC 1A
V3
81
Internal armature fuse intervention signal. 250V AC 1A
82
Table 1.K Heatsink Cooling Fans and Fuse Signal Wire Sizes and Terminal
Specifications
Code(1) Wire Size and Type(2)
Frame
Flexible Multi-core Tightening Torque

230V 460V Terminals (mm2) (mm2) AWG (N•m / lbs•in)
All All All U3, V3, 0.14 - 1.5 0.14 - 2.5 26 - 16 0.4 / 3.5
81, 82
(1)
(2)
Figure 1.28 Frame C Heatsink Cooling Fan and Internal Fuse Signal Terminal Block
Locations
81 82 U3 V3

I/O Wiring Observe the following points when installing I/O wiring:
• Use copper wire only.

• Wire with an insulation rating of 600V or greater is recommended?
Important: I/O terminals labeled “(–)” or “Common” are not referenced to
earth ground and are designed to greatly reduce common mode
interference. Grounding these terminals can cause signal noise.
ATTENTION: Configuring an analog input for current operation

! and driving it from a voltage source could cause component
damage. Verify proper switch configuration prior to applying input
signals. Refer to DIP Switch and Jumper Settings on page 1-32.
ATTENTION: Hazard of personal injury or equipment damage
! exists when using bipolar input sources. Noise and drift in
sensitive input circuits can cause unpredictable changes in motor
speed and direction. Use speed command parameters to help
reduce input source sensitivity.
DIP Switch and Jumper Settings

DIP switches and jumpers on the Control circuit board are used to configure
the drive for flashing firmware to the control board EEPROM, the
appropriate speed feedback device settings, analog input signals and
minimum field current. Most switches and jumpers are set to the
appropriate configuration at the factory.
Figure 1.29 Control Circuit Board DIP Switch and Jumper Locations
Refer to Table 1.L on page 1-33
for descriptions corresponding to
the ID numbers shown below.
= ON
➏
S15
= OFF
1
2
3
4
5
6
7
8
1
=OFF
➊S3
2
3
4
5
RST
S2
6
ACT
S1
7
RUN
8
PWR
➑ S14 ➎ S0
S20
➐
S12 S18
➋
➌ ➍
1
S4
2
➒ ON
3
4
S11
5
S10
S21
6
S9
7
8
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
ENC_5 ENC_12
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 DEBUG
- A B C+ A+ A- B+ B- Z+ Z- COM +V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
- A B C + A+ A- B+ B- Z+ Z- COM +V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Table 1.L Control Circuit Board Jumper and DIP Switch Settings
Jumper/ Factory
ID Switch Function Default
S0 For factory boot flashing only. Leave set to the factory setting. Jumper Off
➊ Jumper On Firmware boot
Jumper Off Normal function
Jumper On Write firmware boot code
Jumper Off Boot code on flash is protected
S2 Not used. Leave set to the factory setting. Jumper Off
Jumper On Reset
Jumper Off Normal function
S4 Configures the input voltage of the DC analog tachometer. 90V
➋ Refer to Table 1.M on page 1-34 for configuration.
S9 Configures the input signal of Analog Input 1 (terminals 1 and 2): On
➌ Off Position 0 - 20 mA / 4 - 20 mA
On Position 0 - 10V / ±10V
Note: The input signal type must also be programmed accordingly
using Par 71 [Anlg In1 Config].
S10 Configures the input signal of Analog Input 2 (terminal 3 and 4): On
Off Position 0 - 20 mA / 4 - 20 mA
S11 Configures the input signal of Analog Input 3 (terminals 5 and 6): On
Off Position 0 - 20 mA / 4 - 20 mA
S12 Not used. Leave set to the factory setting. Off
➍
S14 Field current resistors setting, see Table 1.G on page 1-25. Minimum
➎ field current
Important: In addition, the value selected with switch S14 must be rating
entered in Par 374 [Drv Fld Brdg Cur] in the control based on
software when the drive is commissioned. drive size.
S15 Configuration of the control circuit board to the appropriate drive size. Armature
➏ Leave set to the factory setting, unless the control board has been current
supplied as a spare part. Refer to Table 1.N on page 1-34 and Table based on
1.O on page 1-35 for switch configuration based on drive current drive size.
rating code.
S18 Not used. Leave set to the factory setting. Off
➐
S20 Monitoring of the Z channel of the Digital Encoder on connector XE2: On
➑ Off Position Z-channel monitored
On Position Z-channel not monitored
S21 Encoder power supply voltage and input selection: 12-15 V
➒ Note: When control power is supplied to the drive, the appropriate
LED lights to indicate the selection of the switch.
ENC_5 +5 V encoder (+2.5 - 5.4V input range)
ENC_12 +12-15 V encoder (+5.4V - 15.2V input range)

ATTENTION: The Drive can overspeed if DIP switch S4 is set

! incorrectly, or the tachometer is wired incorrectly. Failure to
observe this precaution could result in damage to, or destruction
of, the equipment.
Figure 1.30 DC Analog Tachometer DIP Switch S4 Example
ON DIP Note: Illustration for example only.
1 2 3 4 5 6 7 8
Table 1.M DC Analog Tachometer DIP Switch S4 Configuration

Maximum DC S4-1 S4-2 S4-3 S4-4
Input Voltage S4-8 S4-7 S4-6 S4-5
22V ON ON ON ON
45V ON ON ON OFF
90V ON ON OFF OFF
180V ON OFF OFF OFF
300V OFF OFF OFF OFF
Figure 1.31 Drive Size DIP Switch S15 Example
ON DIP Note: Illustration for example only.
1 2 3 4 5 6 7 8
Table 1.N Drives with 230V Input - DIP Switch S15 Configuration
Frame
Drive Current
Rating Code S15-1 S15-2 S15-3 S15-4 S15-5 S15-6 S15-7 S15-8
A 7P0 ON OFF OFF OFF OFF OFF OFF OFF
9P0 OFF ON OFF OFF OFF OFF OFF OFF
012 ON ON OFF OFF OFF OFF OFF OFF
020 OFF OFF ON OFF OFF OFF OFF OFF
029 ON OFF ON OFF OFF OFF OFF OFF
038 OFF ON ON OFF OFF OFF OFF OFF
055 ON ON ON OFF OFF OFF OFF OFF
073 OFF OFF OFF ON OFF OFF OFF OFF
093 ON OFF OFF ON OFF OFF OFF OFF
110 OFF ON OFF ON OFF OFF OFF OFF
B 146 ON ON OFF ON OFF OFF OFF OFF
180 OFF OFF ON ON OFF OFF OFF OFF
218 ON OFF ON ON OFF OFF OFF OFF
265 OFF ON ON ON OFF OFF OFF OFF
360 ON ON ON ON OFF OFF OFF OFF
434 OFF OFF OFF OFF ON OFF OFF OFF
C 521 ON OFF OFF OFF ON OFF OFF OFF

Table 1.O Drives with 460V Input - DIP Switch S15 Configuration
Frame
Drive Current
Rating Code S15-1 S15-2 S15-3 S15-4 S15-5 S15-6 S15-7 S15-8
A 4P1 OFF OFF OFF OFF OFF OFF ON OFF
6P0 ON OFF OFF OFF OFF OFF ON OFF
010 OFF ON OFF OFF OFF OFF ON OFF
014 ON ON OFF OFF OFF OFF ON OFF
019 OFF OFF ON OFF OFF OFF ON OFF
027 ON OFF ON OFF OFF OFF ON OFF
035 OFF ON ON OFF OFF OFF ON OFF
045 ON ON ON OFF OFF OFF ON OFF
052 OFF OFF OFF ON OFF OFF ON OFF
073 ON OFF OFF ON OFF OFF ON OFF
086 OFF ON OFF ON OFF OFF ON OFF
100 ON ON OFF ON OFF OFF ON OFF
129 OFF OFF ON ON OFF OFF ON OFF
B 167 ON OFF ON ON OFF OFF ON OFF
207 OFF ON ON ON OFF OFF ON OFF
250 ON ON ON ON OFF OFF ON OFF
330 OFF OFF OFF OFF ON OFF ON OFF
412 ON OFF OFF OFF ON OFF ON OFF
C 495 OFF ON OFF OFF ON OFF ON OFF
667 ON ON OFF OFF ON OFF ON OFF
I/O Signal and Control Wiring

Eight (8) digital inputs, four (4) digital outputs, three (3) analog inputs, and
two (2) analog outputs are available on the standard I/O terminal blocks
provided with the drive. One digital input (1-8) must be configured for
“Enable”. Refer to I/O and Control Wire Routing on page 1-42 for proper I/
O wire routing locations.
Additional digital and analog I/O is available when using the optional I/O
Expansion circuit board. Refer to Appendix F Optional Analog and Digital
I/O Expansion Circuit Board for more information. Also, you can use the
optional 115V AC Converter circuit board to convert 115V AC digital input
signals to 24V DC digital inputs signals to interface with the digital inputs
on the standard I/O terminal blocks. Refer to Appendix G Optional 115V
AC to 24V DC I/O Converter Circuit Board for more information.
Table 1.P Analog I/O, Digital I/O and DC Analog Tachometer Wire Sizes and Terminal
Specifications
Wire Size and Type(1) Tightening
Terminal Block Flexible Multi-core Torque
Signal Type (Terminals) (mm2) (mm2) AWG N•m (lb•in)
Analog and Digital I/O TB1 - 4 (1 - 40)
0.140 - 1.500 0.140 - 1.500 26-16 0.4 (3.5)
DC Analog Tach M3 (+ and –)
(1)

Figure 1.32 I/O Terminal Block Locations
Terminal Block 3 Terminal Block 4
Table 1.Q I/O Terminal Block 1 Designations

No. Signal Description Factory Default Config. Parameter
1 Analog Input 1 (+) Isolated (1), bipolar, differential 1 “Speed Ref A” 70 [Anlg In1 Sel]
2 Analog Input 1 (–) ±10V / 0-20mA or 4-20mA.
1
2 3 Analog Input 2 (+) Important: 0-20mA or 4-20mA operation 0 “Off” 75 [Anlg In2 Sel]
3
4
requires that switch S9, S10, and S11 on
5 4 Analog Input 2 (–) the Control board be in the “Off” position.
6
7
8
5 Analog Input 3 (+) Drive damage may occur if the switch is not 0 “Off” 80 [Anlg In3 Sel]
9
10 6 Analog Input 3 (–) in the correct position based on the type of
input signal. Refer to Table 1.L on
page 1-33.
Max ±10V, Max 0.25mA.
7 +10V Pot Reference 2-5k ohm load. Max ±10V, 10mA. – –
8 –10V Pot Reference
9 Pot Common For (+) and (–) 10V pot references. – –
10 PE ground PE ground to drive chassis. – –
(1)
Differential Isolation - External source must be maintained at less than 160V with respect to PE. Input provides high common mode immunity.
Table 1.R I/O Terminal Block 2 Designations

11 Internal 0V (Gnd) – –
12 Digital Input 1 Max +30V, 15V/3.2mA, 24V/5mA, 2 “Stop/CF” 133 [Digital In1 Sel]
11
12 13 Digital Input 2 and 30V/6.4mA. 3 “Start” 134 [Digital In2 Sel]
13
14
15 14 Digital Input 3 11 “Jog” 135 [Digital In3 Sel]
16
17
18
15 Digital Input 4 1 “Enable”(1) 136 [Digital In4 Sel]
19
20 16 Digital Input Common(2) – –
17 Not Used – –
18 24V Supply Common Common for the internal power supply. – –
19 +24V DC Supply Drive supplied control input power. – –
Max. +20-30V, 200mA(3)
20 PE ground PE ground to drive chassis. – –
(1) A digital input (1-8) must be configured for “Enable”.
(2)
When using the internal +24V DC supply (terminal 19) for digital inputs 1-4, you must connect the digital input common (terminal 16) to the +24V supply common
(terminal 18).
(3)
The total current draw is the sum of encoder power, digital outputs and any other loads connected to terminal 19.

Table 1.S I/O Terminal Block 3 Designations

Factory
No. Signal Description Default Config. Parameter
21 Analog Output 1 (+) Max. ±10V, 5 mA. 12 “Motor Speed” 66 [Anlg Out1 Sel]
22 Analog Output 1 (–)
21
22 23 Analog Output 2 (+) 13 “Motor Curr” 67 [Anlg Out2 Sel]
23
24 24 Analog Output 2 (–)
25
26
27
28
25 Digital Output Common – –
29
30 26 Digital Output 1 Max. +30V, 50mA 5 “Ready” 145 [Digital Out1 Sel]
27 Digital Output 2 9 “Fault” 146 [Digital Out2 Sel]
28 Digital Output 3 2 “Spd Thresh” 147 [Digital Out3 Sel]
29 Digital Output 4 4 “CurrentLimit” 148 [Digital Out4 Sel]
30 External +24VDC Supply Supply voltage for the Digital Outputs. – –
Max. +30V DC, 80mA.
Table 1.T I/O Terminal Block 4 Designations

31 Digital Input 5 Max +30V, 15V/3.2mA, 24V/5mA, 17 “Speed Sel 1” 137 [Digital In5 Sel]
32 Digital Input 6 and 30V/6.4mA. 18 “Speed Sel 2” 138 [Digital In6 Sel]
33 Digital Input 7 19 “Speed Sel 3” 139 [Digital In7 Sel]
34 Digital Input 8 31 “Contactor” 140 [Digital In8 Sel]
31
32 35 Digital Input Common Important: When using the internal +24V – –
33
34 DC supply (terminal 19) for digital inputs
35
36
37
5-8, you must connect the digital input
38
39
common (terminal 35) to the +24V supply
40 common (terminal 18).
36- Not Used – –
40
I/O Wiring Examples

Required Parameter
Input/Output Connection Example Changes
Potentiometer Unipolar • Adjust Scaling:
1
Speed Reference 72 [Anlg In1 Scale] and
2
10k Ohm Pot. Recommended 73 [Anlg1 Tune Scale]
3
(2k Ohm Minimum) • View Signal Value:
4
1404 [Analog In1 Value]
5
• View Signal Output:
6
385 [Speed Ref Out]
7
8
9
10
Joystick Bipolar Speed • Set Direction Mode:

1
Reference (1) 2
1322 [Direction Mode]
±10V Input 3
= 1 “Bipolar”
• Adjust Scaling:
4
72 [Anlg In1 Scale] and
5
73 [Anlg1 Tune Scale]
6
• View Signal Value:
7
1404 [Analog In1 Value]
8
9
385 [Speed Ref Out]
10

Required Parameter
Analog Input Bipolar Speed • Set Direction Mode:
Reference (1) + 1 1322 [Direction Mode]
Common 2
±10V Input = 1 “Bipolar”
3
• Adjust Scaling:
4 72 [Anlg In1 Scale] and
5 73 [Anlg1 Tune Scale]
6 • View Signal Value:
7 1404 [Analog In1 Value]
8 • View Signal Output:
9 385 [Speed Ref Out]
10
Analog Input Unipolar Speed • Configure for Voltage or

Reference + 1 Current:
0 to +10V Input Common 2 71 [Anlg In1 Config](3)
or
3
• Adjust Scaling:
4 72 [Anlg In1 Scale] and
0 to 20 mA
5 73 [Anlg1 Tune Scale]
6 • View Signal Value:
7 1404 [Analog In1 Value]
8
9 385 [Speed Ref Out]
10
Analog Output Bipolar • Select Source Value:

Signal 66 [Anlg Out1 Sel]
±10V Bipolar (based on the – + • Adjust Scaling:
21 62 [Anlg Out1 Scale]
signal of the selected input
22
(i.e., selection “Analog In 1”)
23
0-10V/0-20mA Unipolar
24
(shown)
25
26
27
28
29
30
Enable Input • No Changes Required.

24V DC internal supply 11
12 Note: If the digital input
13 used for “Enable” is
14 changed from the default
15 setting of digital input 4, the
16 wiring must be changed
17 accordingly.
18
19
20
2-Wire Control • Disable Digital Input 1:

Non-Reversing(2) 11 133 [Digital In1 Sel]
24V DC internal supply Stop-Run 12 = 0 “Not Used”
13 • Set Digital Input 2:
14 134 [Digital In2 Sel]
15 = 5 “Run”
16
17
18
19
20

Required Parameter
2-Wire Control • Set Digital Input 1:
11
Reversing(2) Run Fwd. 133 [Digital In1 Sel]
12 = 6 “Run Forward”
24V DC external supply
13 • Set Digital Input 2:
Run Rev. 14 134 [Digital In2 Sel]
15 = 7 “Run Reverse”
16
17
+24V Neutral/
Common 18
19
20
3-Wire Control • No Changes Required.

Stop 11
24V DC internal supply
12
13
Start 14
15
16
17
18
19
20
3-Wire Control • No Changes Required

24V DC external supply Stop 11
Requires 3-wire functions only 12
([Digital In1 Sel]). Using 2-wire 13
selections will cause a type 2 Start 14
alarm (page page 4-7). 15
16
17
18
+24V Neutral/ 19
Common 20
Sourcing Digital Outputs • No Changes Required

External
24V DC external supply External Neutral/
21
+24V DC Common 22
23
24
25
Ready 26
Fault 27
Spd Thresh 28
29
30
(1) Refer to the Attention statement on page 1-32 for important bipolar wiring information.
(2) Important: Programming inputs for 2 wire control deactivates the HIM Start and Jog buttons.
(3)
0-20mA or 4-20mA operation requires that the switch at S9, S10, or S11 be set to the “ON” position or drive
damage may occur. Refer to Table 1.L on page 1-33.

Digital Encoder Terminal Block
The encoder connection cables should always be connected directly to the

terminals on the encoder terminal block. The encoder cable must be made
up of twisted pairs with the shield connected to the shield ground on the
drive side. Do not connect the shield to ground on the motor side. In some
cases (i.e., cable lengths that exceed 100 meters), it may be necessary to
ground the shield of each twisted pair on the power supply. Refer to
page A-3 for Digital Encoder specifications.
Figure 1.33 Digital Encoder Terminal Block Location
Shield ground Digital Encoder Control EMI Shield

terminal block
Table 1.U Digital Encoder Terminal Designations

No. Description
A+ Encoder A Single channel or quadrature A
A- Encoder A (NOT) input
A+ B+ Encoder B Dual channel quadrature B input
A-
B+
B-
B- Encoder B (NOT)
Z+
Z-
CO
Z+ Encoder Z Pulse, marker or registration
M
+V Z- Encoder Z (NOT) input (2)
COM +5/12-15V (1) DC Return Internal power common
+V +5/12-15V (1) DC Power Internal power source
200 mA
(1)
Selectable via switch S21 on the Control board. Refer to Table 1.L on page 1-33.
(2)
Selectable via switch S20 on the Control board. Refer to Table 1.L on page 1-33.

Figure 1.34 Sample Encoder Wiring

I/O Connection Example
Encoder Power – (1)
Internal Drive Power +5/12-15V DC
(200 mA)
Internal (drive) +5/12-15V DC, +V
200mA
COM Common
Z-
Z+
to Shield (1)
B-
B+
A-
A+
Encoder Power –External

Power Source +V
COM
Common
Z-
Z+ to
+
Shield (1)
B- External
Power
B+ Supply
A-
A+
Encoder Signal – to Power

Single-Ended, Dual Channel +V Supply Common
COM
Z NOT
Z-
Z
Z+
B NOT
B-
B
B+
A NOT
A-
A
A+
to Shield (1)
Encoder Signal –Differential,
Dual Channel +V
COM
Z NOT
Z-
Z
Z+
B NOT
B-
B
B+
A NOT
A-
A
A+
to Shield (1)
(1)
Shield connection is on drive Control EMI shield. Refer to Figure 1.33 on page 1-40.

DC Analog Tachometer Terminal Block
Figure 1.35 Analog Tachometer Terminal Block Location
Analog
Tachometer
terminal block
Refer to page A-3 for DC Analog Tachometer specifications.

of, the equipment.
Table 1.V DC Analog Tachometer Terminal Designations

No. Signal Description
– Negative input –
A (Not Used)
− B
A
B
C C
+
+ Positive input 22.7 / 45.4 / 90.7 / 181.6 /
Clockwise rotation = positive 302.9V(1) max voltage
Counterclockwise rotation = negative 8 mA max. current
(1) Maximum voltage depends on the configuration of DIP switch S4. Refer to DC Analog Tachometer DIP Switch
S4 Example on page 1-34
I/O and Control Wire Routing

Route all I/O and control wires from through the bottom of the drive,
between the bottom front protective cover and the terminal cover (frame A)
or plastic covers (frames B and C).

Chapter 2
Drive Start Up
This chapter describes how to start up the PowerFlex DC drive. The drive is
configured at the factory for speed regulation with encoder feedback and
independant motor field current regulation with constant current to control
the motor from zero to base speed.
If using the LCD HIM (Human Interface Module) to commission the drive,
it is recommended that you read Appendix B before performing these
procedures.
ATTENTION: Power must be applied to the drive to perform the

! following start-up procedure. Some of the voltages present are at
incoming line potential. To avoid electric shock hazard or damage
to equipment, only qualified service personnel should perform the
following procedure. Thoroughly read and understand the
procedure before beginning. If an event does not occur while
performing this procedure, Do Not Proceed. Remove Power
including user supplied control voltages. Correct the malfunction
before continuing.
Important: It is recommended that you uncouple the motor from all loads
at this time, until otherwise directed.

2-2 Drive Start Up
Drive Start Up Checklist This checklist contains the major steps required to complete the drive
commissioning procedure.
❏ 1. Verify all Drive Configuration Settings - page 2-2.

❏ 2. Verify the Power Wiring - page 2-2.
❏ 3. Verify the Control and I/O Wiring - page 2-3.
❏ 4. Apply Voltage to the Control Circuits - page 2-4.
❏ 5. Verify the Control Voltages - page 2-5.
❏ 6. Load the Default Settings - page 2-6.
❏ 7. Configure the Most Commonly Used Parameters - page 2-6.
❏ 8. Tune the Current Regulator - page 2-10.
❏ 9. Verify Motor Rotation and Run Feedback Polarity Checks -
page 2-11.
❏ 10. Configure the Speed Feedback Parameters - page 2-14.
❏ 11. Tune the Speed Regulator - page 2-15.
❏ 12. Verify Speed Reference Settings and Drive Operation - page 2-16.
Before Applying Power to 1. Verify all Drive Configuration Settings:

the Drive 1. With the bottom cover removed from the drive (refer to Removing
the Drive Covers on page 1-7), verify that DIP switch S14 is set
correctly to be ≥ the rated field current specified on the motor
nameplate. Refer to Table 1.G on page 1-25.
2. Verify all switch settings (S9, S10, and S11) for the analog inputs.
Refer to Table 1.L on page 1-33.
3. Verify all DIP switch and jumper settings for the digital encoder or
analog tachometer feedback device. Refer to Table 1.L on
page 1-33 and Figure 1.30 on page 1-34.

of, the equipment.
2. Verify the Power Wiring:

Verify that the AC line power at the disconnect device is within the
rated value of the drive and that all power wiring is correct. Refer to
Power Wiring on page 1-15 for further information.
ATTENTION: Do not connect any external power to the

! armature output terminals, personal injury and/or equipment
damage can occur.

Drive Start Up 2-3
3. Verify the Control and I/O Wiring:
1. Verify that control power and I/O wiring is correct. A digital input
(1-8 only) must be wired and configured as a drive enable. Refer to
Control Circuit Input Power on page 1-28 and I/O Wiring on
page 1-32 for further information.
2. If you are using a PTC thermistor or thermal switch to protect the

motor from overloading, remove the 1k ohm resistor between
terminals 78 and 79. Refer to Thermistors and Thermal Switches on
page 1-25

2-4 Drive Start Up
Applying Power to the Drive The remainder of the “Drive Start Up” procedure in this manual uses a HIM
to configure and autotune the drive. If you prefer, you can use the
DriveExplorer™ or DriveTools™ SP software(1) to program drive
parameters or use the drive “Start Up” wizard available with both software
packages.
If an operator interface is not available, remote devices should be used to

start up the drive. For information on using the HIM, refer to the HIM
Overview on page B-1.
Important: When power is first applied, the HIM may require

approximately 5 seconds until commands are recognized
(including the Stop key).
4. Apply Voltage to the Control Circuits:
1. Apply power to the control circuits (terminals U2 and V2) of the

drive. If any of the digital inputs are configured to “Stop/CF” (CF =
Clear Fault), “Enable” or “Aux Fault,” verify that signals are
present or reconfigure [Digital Inx Sel]. If a fault code appears,
refer to Chapter 4 - Troubleshooting on page 4-1.
2. If the STS LED is not flashing green at this point, refer to “Drive
Status Indicators” below.
(1)
You must use DriveExplorer v5.02 or higher or DriveTools SP v4.01 or higher with a PowerFlex DC drive
specific software patch. The patch can be downloaded from http://www.ab.com/support/abdrives/webupdate/

Drive Start Up 2-5
Figure 2.1 Drive Status Indicators
PORT
MOD
NET A
NET B
➋ ➊
STS
# Name Color State Description

➊ STS Green Flashing Drive ready, but not running and no faults are present.
(Status) Steady Drive running, no faults are present.
Yellow Flashing, A condition exists that is preventing the drive from
Drive Stopped starting. Check parameters 1403 [Start Inhibits] and/or
1380 [Drive Alarm 1].
Flashing, An intermittent type 1 alarm condition is occurring.
Drive Running Check parameter 1380 [Drive Alarm 1]. Refer to Fault
Descriptions on page 4-4 and/or Alarm Descriptions on
page 4-7.
Steady, A continuous type 1 alarm condition exists. Check
Drive Running parameter 1380 [Drive Alarm 1]. Refer to Fault
page 4-7.
Red Flashing A fault has occurred. Check [Fault x Code] or view the
Fault Queue on the HIM. Refer to Fault Descriptions on
page 4-4.
Steady A non-resettable, non-configurable fault has occurred.
Check [Fault x Code] or view the Fault Queue on the
HIM. Refer to Fault Descriptions on page 4-4.
➋ PORT Refer to the Communication Status of DPI port internal communications (if present).
MOD Adapter User Manual. Status of communications module (when installed).
NET A Status of network (if connected).
NET B Status of secondary network (if connected).
5. Verify the Control Voltages:
❏ Verify that the following voltages are present at I/O terminal block
1 and 2. Refer to I/O Signal and Control Wiring on page 1-35:
Terminal Number . . . Voltage to Terminal Number . . .
7 +10V 9
8 -10V 9
19 +24 - 30V 18

2-6 Drive Start Up
6. Load the Default Settings:

It is recommended that you reset the drive to the default settings. By
resetting the drive to the default settings, any previous parameter
modifications you have made will be overwritten.
1. On the HIM, from the “Main” menu scroll to the “Memory

Storage” menu and press Enter.
2. Scroll to “Reset To Defaults” and press Enter. A message displays

to verify that you want to reset the drive to the factory settings.
3. Press Enter.
Note: A “Params Defaulted” (F48) entry will be made in the drive’s

Fault Queue to indicate the change.
7. Configure the Most Commonly Used Parameters:

If your application only requires basic drive parameter set up, you can
use the S.M.A.R.T. list screen available on the HIM to program the
drive. Refer to Using the S.M.A.R.T. List Screen on page B-2 for more
information.
Important: In order to access all parameters in this procedure you must
set the Parameter View option to “Advanced”.
1. At the Main menu, scroll to the Parameter option and press the ALT
and then Sel button.
2. Scroll to the Numbered List option and press Enter.
3. Type 211 and press Enter.
4. Press the Sel button.
5. Type 1 and press Enter.
6. Press the Esc button.
7. Press the ALT and then Sel button.
8. Scroll to the File-Group-Par option and press Enter.
9. Scroll to the “Motor Control” file and press Enter.

Drive Start Up 2-7
10. With the “Motor Data” group selected, press Enter and configure
the following parameters:
❏ 45 [Max Ref Speed] - Enter the motor nameplate base speed. If

the application requires field weakening to operate above base
speed, enter the maximum reference speed required.
❏ 162 [Max Feedback Spd] - Enter the motor nameplate base
speed. If the application requires field weakening to operate
above base speed, enter the maximum feedback speed that
could be encountered.
❏ 175 [Rated Motor Volt] - Enter the rated motor nameplate

armature voltage. This value should be the measured armature
voltage when the motor is running at base speed with rated field
current. This value should represent 100% of the rated armature
voltage when field weakening is not used. If field weakening is
used, this value should be set to 90% of the rated armature
voltage to prevent a possible overvoltage condition when the
drive transitions to the field weakening mode.
❏ 179 [Nom Mtr Arm Amps] - Enter the rated motor nameplate
armature current.
❏ 374 [Drv Fld Brdg Cur] - Enter the rated current of the field
bridge regulator to match the value set using the DIP switch
S14. Refer to Field Current Resistors on page 1-24.
❏ 280 [Nom Mtr Fld Amps] - Enter the rated motor nameplate
field current.

2-8 Drive Start Up
11. Access the “Field Config” group and configure the following
parameters:
❏ If the motor field power is supplied by an external source, set

Par 497 [Field Reg Enable] = 0 “Disabled”. Otherwise, verify
that this parameter is set to 1 “Enabled” (default).
❏ If you are utilizing field economy when the drive is stopped or
at zero speed, set Par 1407 [Field Econ Delay] to the desired
amount of time to elapse after the drive stops or reaches zero
speed before field economy becomes active (the value set in Par
468 [Min Fld Curr Pct]). The default value is 300 seconds.
❏ Par 469 [Field Mode Sel] - select the desired field mode
(default = 0 “Base Speed”, constant field current):
❍1 “Field Weaken”, field weakening mode
❍2 “External”, power to the field is supplied externally
❏ If you are utilizing field economy at zero speed, set 468 [Min
Fld Curr Pct] to the desired minimum field current for field
economy (default = 30%).
❏ If you are operating the drive in field weakening mode, set Par
456 [Fld Weaken Ratio] = Motor nameplate base speed / Par 45
[Max Ref Speed] x 100.
Important: When operating the drive in field weakening mode, it is

necessary to refer to the CEMF value or to the crossover
data. If the maximum field current is not within 10% of the
maximum value of the internal field converter, configure
the current feedback using DIP switch S14. Refer to Field
Current Resistors on page 1-24.

Drive Start Up 2-9
12. Access the “Utility” file and press Enter.
13. Access the “Alarms” group and configure the following parameters:
❏ Par 481 [UnderVolt Thresh] - Enter the value at which a drive
under voltage condition will be detected (default = 230V).
❏ Par 584 [OverCurrent Thr] - Enter the value at which a drive

over current condition will be detected (default = 175%). The
threshold level should be at least 10% above the selected
operating current limit (Par 7 [Current Limit]).
14. Access the “Input & Output” file and press Enter.
15. Access the “Analog Inputs” group and configure the following:
❏ If you have connected a potentiometer to analog input 1 for a

speed reference:
❍Verify that Par 70 [Anlg In1 Sel] is set to 1 “Speed Ref A”

(default).
❍Verify that switch S9 and Par 71 [Anlg In1 Config] are

configured to match (voltage versus a current signal). Refer
to DIP Switch and Jumper Settings on page 1-32.
❍Set Par 72 [Anlg In1 Scale] and Par 74 [Anlg In1 Offset]
appropriately.
❏ If you are using the HIM on the drive cover (Port 1) for the
speed reference, set Par 70 [Anlg In1 Sel] to 0 “Off”.
16. Access the “Digital Inputs” group and configure the following
parameters:
❏ Par 1391 [ContactorControl] - Select the type of contactor(s)

used with the drive: 1 “Contactor” (default, AC input or DC
output contactor), 2 “Contactor+DB” (AC input or DC output
contactor and dynamic brake contactor), or 0 “None”.
Note: If you select 0 “None” for Par 1391 [ContactorControl], a

“CntactrCflct” alarm will display. The alarm will be resolved
and automatically clear when you complete the Digital Output
configuration below.
Note: If Par 1391 [ContactorControl] is set to 1 or 2, an

Auxiliary Status contactor must be wired to a digital input
(default for digital input 8).
❏ Par 140 [Digital In8 Sel] - If a contactor is NOT used, set to

other than 31 “Contactor” (e.g., 0 “Not Used”).
❏ If an auxiliary status contactor is wired to a digital input, set the

appropriate [Digital Inx Sel] parameter to 31 “Contactor”.

2-10 Drive Start Up
17. Access the “Digital Outputs” group and configure the following
parameters:
❏ If a contactor and a dynamic brake resistor is used:
❍Par 629 [Relay Out 2 Sel] = 24 “ContactorDB”.
❏ If a neither a contactor and a dynamic brake resistor is used:
❍Par 629 [Relay Out 2 Sel] = Set to other than 24

“ContactorDB” or 25 “Contactor” (e.g., 0 “Not Used”).
❍Par 1392 [Relay Out 1 Sel] = Set to other than 24

“ContactorDB” or 25 “Contactor” (e.g., 0 “Not Used”).
18. If you are using the HIM on the drive cover (Port 1) for the speed
reference, access the “DPI Inputs” group and set the appropriate
[DPI Px Select] parameter to 1“Speed Ref A”.
8. Tune the Current Regulator:
ATTENTION: Prior to tuning the current regulator, you must

! provide a hard wired maintained external operator accessible
coast/stop push button to disable the machine in case of improper
operation. Uncontrolled machine operation can result if this is
not done. Failure to observe this precaution could result in severe
bodily injury or loss of life.
ATTENTION: Prior to tuning the current regulator, uncouple
! the motor from equipment or processes that may be damaged by
incorrect rotation of the motor or speed references.
Complete this test before running the drive for the first time. Upon
completing this tuning procedure, the armature resistance value is
stored in Par 453 [Arm Resistance] and the armature inductance value is
stored in Par 454 [Arm Inductance]. If needed, these values can be
manually adjusted.
1. If an external supply is used to power the motor field, disconnect

the wires from the motor field terminals. If the drive supplies power
to the motor field, the internal field circuit will automatically be
disabled during this test.
Important: The drive must be under at least a 40% load in order to

properly tune the current regulator. Verify that the motor
does not start rotating during the Current Regulator tuning
test (due to remnant magnetization, field series, etc.). If
necessary, mechanically block the motor shaft so it does
not turn.

Drive Start Up 2-11
2. Access the “Motor Control” file, the “Torq Attributes” group and
set Par 7 [Current Limit] to the appropriate level for your
application. This parameter defaults to 150%. The drive’s armature
output current will correspond to Par 179 [Nom Mtr Arm Amps] x
Par 7 [Current Limit].
Note: Par 8 [Current Lim Pos], the drive current limit for the
positive direction and Par 9 [Current Lim Neg], the drive
current limit for the negative direction, are set to 150% by
default. If necessary, you can change the value of these
parameters to suit your application.
3. Access the “Speed Feedback” group and verify that Par 414 [Fdbk
Device Type] is set to 3 “Armature” (default).
4. Press the Esc key until you return to the “File” menu and access Par
452 [CurrReg Autotune] in the “Autotune” group, in the “Motor
Control” file, and select 1 “On” and press Enter.
5. Press the Start button on the HIM. This will start the current
regulator auto tuning test, which could take several minutes.
At the end of the test, the drive will automatically be stopped and
Par 452 [CurrReg Autotune] will be set to 0 “Off”.
If the value of Par 587 [I Reg Error] is greater than -/+40, refer to
Manually Adjusting the Current Regulator Tune Settings on page C-26
for more information.
If a drive fault occurs during the tuning procedure, refer to Fault
Descriptions on page 4-4 for a list of fault descriptions and actions.
9. Verify Motor Rotation and Run Feedback Polarity Checks:
The jog function (on the HIM or terminal block) will be used to check
motor direction and encoder operation. If the STS LED is not flashing green
at this point, refer to Figure 2.1 on page 2-5 for more information.
ATTENTION: Prior to running the motor direction and polarity

! checks, you must provide a hard wired maintained external
operator accessible coast/stop push button to disable the machine
in case of improper operation. Uncontrolled machine operation
can result if this is not done. Failure to observe this precaution
could result in severe bodily injury or loss of life.
ATTENTION: Prior to running the motor direction and polarity
! checks, uncouple the motor from equipment or processes that
may be damaged by incorrect rotation of the motor or speed
references.

2-12 Drive Start Up
1. When checking motor polarity, the drive will have power applied
and the motor will rotate. Verify that the motor is uncoupled from
the load. If the motor cannot be uncoupled from the load, the
following motor checks are recommended:
❏ All electrical connections are tight.
❏ The brushes are properly seated.
❏ The motor shaft is free to rotate.
2. Access the “Motor Control” file, “Speed Feedback” group and

verify that Par 414 [Fdbk Device Type] is set to 3 “Armature”
(default).
3. Access the “Speed Command” file, “Discrete Speeds” group and

verify that Par 266 [Jog Speed] is set to the default value (100
RPM) or to an acceptable speed level for this test.
4. If analog input 1 is wired, access the “Analog Inputs” group and

verify that the voltage level is 0V in Par 1404 [Analog In1 Value].
5. While viewing Par 233 [Output Voltage], assert a Jog command

(via the HIM keypad or digital input on the I/O terminal block) and
observe the motor rotation direction. Verify whether or not Par 233
[Output Voltage] is positive.
6. If the observed rotation direction is incorrect, remove power from

the drive and continue with step 6 below, while referring to the
motor connection diagrams in Figure 2.2 below. If the observed
rotation direction is correct, continue with step 10 below.
7. Make certain power is turned off and locked out.

8. Switch the armature leads connected to C (+) and D (-).
Figure 2.2 Motor Connections
C1 (+) F1 (+) C1 (+) F1 (+)

(2) (2)
C (+) A1 C (+) A1
(2) (2)
D (-) A2 D (-) A2
D1 (-) F2 (-) D1 (-) F2 (-)

PowerFlex DC Motor PowerFlex DC Motor
Straight Shunt Machine, Straight Shunt Machine,

CCW Rotation Facing Commutator End CW Rotation Facing Commutator End

Drive Start Up 2-13
9. Apply power to the drive.
10. Repeat steps 4 and 5 above and verify that the motor rotation is
correct.
11. Complete the appropriate procedure based on the type of feedback

device used for the application:
❏ For Armature Voltage feedback - Continue with Step 10
Configure the Speed Feedback Parameters: on page 2-14.
❏ For Analog Tachometer feedback - Assert a Jog command and

verify that the sign and value of Par 1408 [Tachometer Speed]
corresponds with the actual direction of the motor. If the sign
and value of Par 1408 [Tachometer Speed] and the motor
direction do not correspond, remove power from the drive and
reverse the tachometer connections at the drive. Continue with
Step 10 Configure the Speed Feedback Parameters: on
page 2-14.
❏ For Encoder feedback - Assert a Jog command and verify that

the sign and value of Par 420 [Encoder Speed] correspond with
the actual direction of the motor. If the sign and value of [Par
420 [Encoder Speed] and the motor direction do not
correspond, remove power from the drive and reverse the
encoder connections at the drive. Reverse the polarity of only
one channel, e.g., B and B NOT. Refer to Table 1.U on
page 1-40 for digital encoder terminal block designations.
Continue with Step 10 Configure the Speed Feedback
Parameters: on page 2-14.

2-14 Drive Start Up
10. Configure the Speed Feedback Parameters:
1. Access the “Speed Feedback” group and configure the following

parameters:
❏ Par 414 [Fdbk Device Type] - Select the source for motor
velocity feedback: 1 “Encoder”, 2 “DC Tach” or 3 “Armature”
(default). If operating the drive in field weakening mode, Par
414 [Fdbk Device Type] must be set to 1 "Encoder" or 2 "DC
Tach".
❏ Par 457 [Spd Fdbk Control] - If you are using an encoder or
tachometer, set this parameter to 1 “Enabled” to activate speed
feedback control.
❏ If the speed feedback source is an analog tachometer, set the
fine scaling value in Par 562 [Anlg Tach Gain]. This value is
used to scale the analog tachometer feedback signal after it has
been conditioned by the drive hardware.
ATTENTION: The drive can overspeed if DIP switch

! S4 is set incorrectly, or the tach is wired incorrectly.
Failure to observe this precaution could result in damage
to the drive or process equipment. Refer to Figure 1.30 on
page 1-34.
❏ If the speed feedback source is a digital encoder, enter the

pulses per revolution from the encoder nameplate in Par 169
[Encoder PPR].
❏ If the speed feedback source is a digital encoder, set Par 652

[Encoder Err Chk] to 1 “Enabled” to activate monitoring of the
digital encoder signals (verifies the presence of the A, B, A-, B-
signals). Par 457 [Spd Fdbk Control] must be set to 1
“Enabled” for encoder monitoring to occur. Switch S20 must be
set correctly to prevent Encoder faults. Refer to Table 1.L on
page 1-33.
2. Access the “Speed Command” file and press Enter.
3. With the “Limits” group selected, press Enter and configure the
following parameters:
❏ Par 1 [Minimum Speed] - Enter the minimum speed reference

limit.
❏ Par 2 [Maximum Speed] - Enter the maximum speed required

by the application (this can be above the motor base speed if
field weakening is used).

Drive Start Up 2-15
4. Access the “Dynamic Control” file and press Enter.
5. Access the “Ramp Rates” group and configure the following

parameters:
❏ Par 660 [Accel Time 1] - Set the desired acceleration ramp

time.
❏ Par 662 [Decel Time 1] - Set the desired deceleration ramp
time.
11. Tune the Speed Regulator:
The speed regulator auto tuning test detects the total inertia value of the
motor shaft (in Kg-m2), the friction value (in N-m) and the calculation of the
proportional (P) and integral (I) gains of the speed regulator.
ATTENTION: This test requires the free rotation of the

! motor shaft combined with the load. The auto tuning test
of the speed loop cannot be carried out on machines with
a limited stroke.
Important: The test is carried out by using the torque limit value set in
the Par 1048 [Autotune Cur Lim] (recommended value =
20%). The torque reference is applied via a step reference
(without a ramp); therefore there must not be any
“backlash” in the mechanical transmission and it must be
compatible with those operations using the torque limit
value set in the Par 1048 [Autotune Cur Lim]. You can
modify the torque limit value via this parameter.
Important: In applications where the system total inertia value is very
high, it is necessary to increase the value of Par 1048
[Autotune Cur Lim] in order to avoid “Time out” errors.
The speed regulator auto tuning test of the speed loop is not
suitable for drives used in “elevator” and/or lifting system
applications.
1. While still in the “Autotune” group, configure the motor shaft

rotation direction via Par 1029 [Speed Tune Dir]; 1 “Forward” =
clockwise or 2 “Reverse” = counter-clockwise, with reference to
the motor commutator end.
2. Select the Par 1027 [Spd Reg Autotune], enter “1” and press Enter.

2-16 Drive Start Up
3. Press the Start button on the HIM. This will start the speed regulator
auto tuning test, which could take several minutes. When the test
has been completed, the drive will automatically stop.
During the test the following are completed:
❏ An acceleration test, with the torque limit value set in the Par
1048 [Autotune Cur Lim].
❏ A deceleration test, with a lower torque limit value applied,

until zero speed has been reached.
❏ Par 1013 [Torque Const] is calculated and updated based on the

entered motor data.
The test threshold speed is 33% of the lowest value set in the
following Pars:
❏ 45 [Max Ref Speed]
❏ 3 [Max Speed Fwd] or 4 [Max Speed Rev] based on the rotation

direction chosen in Par 1029 [Speed Tune Dir]
The drive will determine the speed loop gains (Pars 87 [Spd Reg Kp]
and 88 [Spd Reg Ki]) based on the motor and load inertia and friction
characteristics.
If any fault occur during the test, refer to Auto Tuning Faults on
page 2-17 for a description and more information.
Note: If any manual adjustments are required (due to vibrations,
etc.), these should be carried out according to the value of
the integral gain Par 88 [Spd Reg Ki]. If the speed regulator
auto tuning test does not provide satisfactory results, refer
to Fine Tuning the Regulators on page C-25.
The values determined by the Speed Regulator tuning tests are updated
in Pars 87 [Spd Reg Kp], 88 [Spd Reg Ki], 1014 [Inertia] and 1015
[Friction] and displayed in the corresponding Pars 1032 [Speed Tune
Kp], 1033 [Speed Tune Ki], 1030 [Spd Tune Inertia] and 1031
[SpdTune Friction], respectively. The values of Pars 1030 - 1033 can be
used as a record of the Speed Regulator auto tuning results if the values
of Pars 87, 88, 1014 and 1015 are subsequently changed.
12. Verify Speed Reference Settings and Drive Operation:

Verify the following speed and direction (for four quadrant drives)
references of the drive under a load.
ATTENTION: This test requires the free rotation of the

! motor shaft combined with the load. All of the steps in
the “Drive Start Up” procedure must have been
completed before completing this step.

Drive Start Up 2-17
1. Set the speed reference to “0” (zero) using the assigned source
(HIM or analog potentiometer). Refer to Reference Control on
page C-13 for more information on speed reference sources.
2. View Par 385 [Speed Ref Out] and verify that the value is “0”.
3. Press the Start button on the HIM and slowly increase the speed
reference until full speed is reached (viewed in Par 385 [Speed Ref
Out] ).
4. If using a four quadrant (regenerative) drive, press the Direction

button on the HIM and verify that the motor ramps down to “0”
speed and then to full speed in the opposite direction.
5. Press the Stop button on the HIM and verify that the drive ramps to
“0” speed and stops.
Auto Tuning Faults

Following is a list of faults that may display during the speed regulator
auto tuning test. In some cases, the drive’s control circuits may detect a
value(s) that is out of range for the configuration settings during the
speed regulator auto tuning test. In these cases, make the suggested
adjustments and repeat the test. If the fault occurs again, complete the
Fine Tuning the Regulators procedures beginning on page C-25.
Fault No. Description Action
STune 56 The measured motor speed is Decrease the value of Par 1048
Overspeed too high during the speed [Autotune Cur Lim] and repeat the
regulator auto tuning procedure. auto tune procedure.
STune Stalled 57 The drive stalled during the Increase the value of Par 1048
speed regulator auto tuning [Autotune Cur Lim] and repeat the
procedure. auto tune procedure.
STune LoadHi 58 The loading torque value is too Decrease the load torque, where
high at zero speed to complete applicable, and repeat the auto
the speed regulator auto tuning tune procedure.
procedure.
STune CurLimit 59 The value of Par 1048 [Autotune Decrease the value of Par 1048
Cur Lim] for auto tuning the [Autotune Cur Lim] and repeat the
speed regulator is set too high. auto tune procedure.
STune FrictionLo 60 The friction value attained during Decrease the value of Par 1048
the auto tuning procedure is zero [Autotune Cur Lim] and repeat the
or lower than the control auto tune procedure.
precision limit.
STune Timeout 61 The speed regulator auto tuning Verify the value in Par 1048
procedure did not complete [Autotune Cur Lim]. If this value is
within the available time. set to low, the motor will not be
able to reach a maximum speed of
33% of the lower of the values in
Par 45 [Max Ref Speed] or Par 3
[Max Speed Fwd] or Par 4 [Max
Speed Rev] and not be able to
complete the test. Set these values
appropriately and repeat the auto
tuning procedure.
STune Aborted 62 The speed regulator auto tuning Informational only.
procedure has been stopped by
the user.

2-18 Drive Start Up
For additional regulator fine tuning procedures, refer to Fine Tuning the
Regulators on page C-25.
Speed-Up Function
Oscillation may occur during a speed change with loads presenting a high
moment of inertia. These oscillations can be reduced by enabling the
“Speed Up” function. Refer to Speed Up Function on page C-20 for more
information.
Configuring the Speed Zero Logic

The speed zero logic is factory set to 0 “Disabled”. Refer to Speed Zero
Function on page C-22 for more information.
Adaptive Speed Regulation

The adaptive function of the speed regulator is factory set to 0 “Disabled”. It
should only be used when the gain of the speed regulator must go higher
than the speed range. For instructions on configuring these parameters refer
to Adaptive Speed Regulator on page C-17.

Chapter 3
Programming and Parameters
This chapter provides a complete listing and description of the PowerFlex

DC drive parameters. The parameters can be programmed (viewed/edited)
using a Human Interface Module (HIM). As an alternative, programming
can also be performed using DriveExplorer™ or DriveTools™ SP
software(1) and a personal computer. Refer to Appendix B for a brief
description of the LCD HIM. Refer to Appendix D for drive control block
diagrams.
For information on . . . See page . . .
About Parameters 3-1
How Parameters are Organized 3-3
Monitor File 3-11
Motor Control File 3-14
Speed Command File 3-23
Dynamic Control File 3-29
Applications File 3-34
Utility File 3-46
Communications File 3-58
Input / Output File 3-62
Parameter Cross Reference – by Name 3-72
Parameter Cross Reference – by Number 3-77
About Parameters To configure a drive to operate in a specific way, certain parameters may
need to be changed from the default value. Three types of parameters exist:
• ENUM Parameters
ENUM parameters allow a selection from two or more items. The LCD
HIM will display a text message for each item.
• Bit Parameters
Bit parameters have individual bits associated with features or
conditions. If the bit is “0”, the feature is off or the condition is false. If
the bit is “1”, the feature is on or the condition is true.
• Numeric Parameters
These parameters have a single numerical value and unit (i.e. 0.1 Volts).
The example on the following page shows how each parameter type is
presented in this manual.
(1)
You must use DriveExplorer v5.02 or higher or DriveTools SP v4.01 or higher with a PowerFlex DC drive
specific software patch. The patch can be downloaded from http://www.ab.com/support/abdrives/webupdate/

3-2 Programming and Parameters
➊ ➋ ➌ ➍ ➎ ➏
Related
Group
File
No. Parameter Name & Description Values

388 [Flying Start En] Default: 0= “Disabled”
A Enables/Disables the ability of the drive to connect to a Options: 0= “Disabled”
spinning motor at actual RPM when a start command is 1= “Enabled”
issued.
• “Enabled” = When the drive is turned on, the speed of the
motor is measured and the ramp output is set accordingly.
The drive then runs at the set reference value.
SPEED COMMAND
• “Disabled” = When the drive is turned on, the ramp starts

Speed Regulator
from zero.
Main uses:
•To connect to a motor that is already spinning due to its
load (e.g. in the case of pumps, the flowing medium).
•Re–connection to a spinning motor after a fault or alarm.
Note: If the Flying Start function is disabled, ensure that the
motor is not spinning when the drive is turned on, or harsh
motor deceleration in current limit may occur.
445 [Spd Up Gain Pct] Default: 0.00
A The Speed Up function gain as a percentage of Par 446 Min/Max: 0.00 / 100.00
[Speed Up Base]. Units: %
591 [Logic Mask] 1377

Determines which ports can control the drive when Par 1377 [Write Mask Act], bit 15 is set to “1.” If the bit for a port is
set to “0,” the port will have no control functions except for stop. 0 = Control Masked, 1 = Control Permitted, x =
COMMUNICATIONS
Masks & Owners
Reserved.
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Digital In
Default x x x x x x x x x x 0 0 0 0 1 1
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
No. Description
➊ File – Lists the major parameter file category.
➋ Group – Lists the parameter group within a file.
➌ No. – Parameter number. A = The parameter is only accessible when Par 211 [Param Access Lvl] = 1 “Advanced”.
= The parameter value cannot be changed until the drive is stopped.
➍ Parameter Name & Description – Parameter name as it appears on an LCD HIM, with a brief description of the parameters function.
➎ Values – Defines the various operating characteristics of the parameter. Three types exist.
ENUM Default: Lists the value assigned at the factory. “Read Only” = no default.
Options: Displays the programming selections available.
Bit Bit: Lists the bit place holder and definition for each bit.
Numeric Default: Lists the value assigned at the factory. “Read Only” = no default.
Min/Max: The range (lowest and highest setting) possible for the parameter.
Units: Unit of measure and resolution as shown on the LCD HIM.
Important: Some parameters will have two unit values:
• E.g.: Analog inputs can be set for current or voltage as with Par 71 [Anlg Inx Config].
Important: When sending values through DPI ports, simply remove the decimal point to arrive at the correct value (i.e. to
send “5.00 RPM”, use “500”).
➏ Related – Lists parameters (if any) that interact with the selected parameter. The symbol “ ” indicates that additional parameter
information is available in Appendix C - Application Notes on page C-1.

Programming and Parameters 3-3
How Parameters are The LCD HIM displays parameters in a File–Group–Parameter or Numbered
Organized List view order. To switch display mode, access the Main Menu, press ALT,
then Sel (View) while the cursor is on the Parameter menu selection. In
addition, using Par 211 [Param Access Lvl], you have the option to display
the most commonly used parameters (Basic Parameter view) or all
parameters (Advanced Parameter View).
File–Group–Parameter Order
This simplifies programming by grouping parameters that are used for
similar functions. The parameters are organized into files. Each file is
divided into groups, and each parameter is an element in a group. By
default, the LCD HIM displays parameters by File–Group–Parameter view.
Numbered List View

All parameters are in numerical order.
Cross Reference Tables

Refer to Parameter Cross Reference – by Name on page 3-72 and Parameter
Cross Reference – by Number on page 3-77 for a list of parameters and
page numbers.

Basic Parameter View

Parameter 211 [Param Access Lvl] set to option 0 “Basic”.
File Group Parameters

Monitor Speed Meters [Speed Ref A] 44 [Ramp In Pct] 111 [Spd Feedback] 122
Monito
[Speed Ref A Pct] 47 [Ramp Out] 113 [Spd Feedback Pct] 121
r
[Speed Ref B] 48 [Ramp Out Pct] 114 [Actual Speed] 924
[Speed Ref B Pct] 49 [Speed Draw Out] 1018 [Encoder Speed] 420
[Speed Ref Out] 385 [Spd Draw Out Pct] 1019 [Tachometer Speed] 1408
[Spd Ref Out Pct] 384 [Speed Reg In] 118
[Ramp In] 110 [Speed Reg In Pct] 117
Current Meters [Spd Reg Out Pct] 236 [Field Current] 351 [Filt TorqCur Pct] 928
[Current Reg In] 41 [Fld Current Pct] 234 [Field Ref Pct] 500
[Arm Current] 200 [Cur Lim Pos Out] 10
[Arm Current Pct] 199 [Cur Lim Neg Out] 11
Drive Data [FaultCode] 57 [Output Voltage] 233 [Drive Size] 465
[AC Line Voltage] 466 [Output Power] 1052 [Elapsed Lifetime] 235
[AC Line Freq] 588 [Drive Type] 300 [Software Version] 331
Motor Control Motor Data [Max Ref Speed] 45 [Rated Motor Volt] 175 [Nom Mtr Fld Amps] 280
Motor
Contr
[Max Feedback Spd] 162 [Nom Mtr Arm Amps] 179 [Drv Fld Brdg Cur] 374
ol
Field Config [Field Reg Enable] 497 [Field Mode Sel] 469 [Fld Weaken Ratio] 456
[Field Economy En] 499 [Max Fld Curr Pct] 467
[Field Econ Delay] 1407 [Min Fld Curr Pct] 468
Torq Attributes [Current Limit] 7 [Torque Ref] 39 [Zero Torque] 353
[Current Lim Pos] 8 [Trim Torque] 40
[Current Lim Neg] 9 [Torque Reduction] 342
Speed Feedback [Fdbk Device Type] 414 [Anlg Tach Zero] 563 [SpdReg FB Bypass] 458
[Anlg Tach Gain] 562 [Spd Fdbk Control] 457
Autotune [Autotune Cur Lim] 1048 [Spd Reg Autotune] 1027 [Spd Tune Inertia] 1030
[CurrReg Autotune] 452 [Speed Tune Dir] 1029 [SpdTune Friction] 1031
[Arm Resistance] 453 [Speed Tune Kp] 1032
[Arm Inductance] 454 [Speed Tune Ki] 1033
Speed Command Limits [Minimum Speed] 1 [Min Speed Rev] 6 [Max Speed Fwd] 3
Speed
Comm
[Min Speed Fwd] 5 [Maximum Speed] 2 [Max Speed Rev] 4
and
Discrete Speeds [Jog Speed] 266 [Preset Speed 3] 156 [Preset Speed 7] 160
[Jog Off Delay] 1409 [Preset Speed 4] 157 [TB Manual Ref] 267
[Preset Speed 1] 154 [Preset Speed 5] 158
Speed [Trim Ramp] 42 [Trim Speed] 43 [Speed Ratio] 1017
References [Trim Ramp Pct] 378 [Trim Speed Pct] 379
Speed Regulator [Speed Reg En] 242 [Spd Reg Kp] 87 [Spd Reg Ki] 88
[Arm Volt Kp] 493 [Arm Volt Ki] 494
Dynamic Control Ramp Rates [Speed Ramp En] 245 [Accel Time 2] 24 [Jog Ramp Time] 1410
[Ramp Type Select] 18 [Decel Time 2] 32 [S Curve Time] 19
Dynam
ic Con
trol
[Accel Time 1] 660 [MOP Accel Time] 22
[Decel Time 1] 662 [MOP Decel Time] 30
Restart Modes [Start At Powerup] 1344 [Powerup Delay] 1345


Utility Reference Config [Direction Mode] 1322 [Man Ref Preload] 210 [MOP Select] 1375
Utility
[Save HIM Ref] 209 [Save MOP Ref] 249
Drive Memory [Param Access Lvl] 211 [Reset Defaults] 258
Diagnostics [Drive Status 1] 381 [Start Inhibits] 1403 [At Zero Speed] 395
[Drive Status 2] 382 [Drive Logic Rslt] 1328 [CurrLimit Active] 349
[Last Stop Source] 1402 [At Speed] 394 [Spd Limit Active] 372
Faults [Clear Fault Que] 263 [Status2 at Fault] 1350 [Fault Voltage] 1374
[Fault Clear] 1347 [Fault Arm Amps] 1371 [Fault 1 Code] 1351
[Fault Clr Mode] 1348 [Fault Speed] 1372
[Status1 at Fault] 1349 [Fault Field Amps] 1373
Alarms [Drive Alarm 1] 1380
Communications Comm Control [DPI Baud Rate] 589 [DPI Fdbk Select] 1321 [DPI Port Value] 1343
Comm
unicat
[DPI Port Sel] 590
ion
Masks & Owners [Logic Mask] 591 [MOP Mask] 598 [Reference Owner] 604
[Start Mask] 592 [Local Mask] 599 [Accel Owner] 605
[Jog Mask] 593 [Decel Mask] 631 [Fault Clr Owner] 606
[Direction Mask] 594 [Stop Owner] 600 [MOP Owner] 607
[Reference Mask] 595 [Start Owner] 601 [Local Owner] 608
[Accel Mask] 596 [Jog Owner] 602 [Decel Owner] 609
[Fault Clr Mask] 597 [Direction Owner] 603
Datalinks [Data In A1] 610 [Data In D1] 616 [Data Out C1] 622
[Data In A2] 611 [Data In D2] 617 [Data Out C1] 623
[Data In B1] 612 [Data Out A1] 618 [Data Out D1] 624
[Data In C1] 614 [Data Out B1] 620 [Data In Val Sel] 1319
[Data In C2] 615 [Data Out B2] 621 [Data In SelData] 1320
Input / Output Analog Inputs [Anlg In1 Sel] 70 [Anlg In1 Target] 295 [Anlg In1 Cmp Eq] 1045
Inputs
[Anlg In1 Config] 71 [Anlg In2 Target] 296 [Analog In1 Value] 1404
/ Outpu
ts [Anlg In2 Sel] 75 [Anlg In3 Target] 297 [Analog In2 Value] 1405
[Anlg In2 Config] 76 [Anlg In1 Cmp] 1042 [Analog In3 Value] 1406
[Anlg In3 Sel] 80 [Anlg In1 Cmp Err] 1043
[Anlg In3 Config] 81 [Anlg In1 Cmp Dly] 1044
Analog Outputs [Anlg Out1 Sel] 66 [Anlg Out4 Sel] 69 [Analog Out3 Scale] 64
[Anlg Out2 Sel] 67 [Analog Out1 Scale] 62 [Analog Out4 Scale] 65
[Anlg Out3 Sel] 68 [Analog Out2 Scale] 63
Digital Inputs [Dig In Status] 564 [Digital In9 Sel] 141 [Dig In Term 6] 570
[Digital In1 Sel] 133 [Digital In10 Sel] 142 [Dig In Term 7] 571
[Digital In4 Sel] 136 [Dig In Term 1] 565 [Dig In Term 10] 574
[Digital In7 Sel] 139 [Dig In Term 4] 568
[Digital In8 Sel] 140 [Dig In Term 5] 569
Digital Outputs [Dig Out Status] 581 [Digital Out4 Sel] 148 [Digital Out8 Sel] 152
[Digital Out1 Sel] 145 [Digital Out5 Sel] 149 [Relay Out 1 Sel] 1392
[Digital Out2 Sel] 146 [Digital Out6 Sel] 150 [Relay Out 2 Sel] 629
[Digital Out3 Sel] 147 [Digital Out7 Sel] 151
DPI Inputs [DPI P1 Select] 1323 [DPI P3 Select] 1325 [DPI P5 Select] 1327
[DPI P2 Select] 1324 [DPI P4 Select] 1326

Advanced Parameter View

Parameter 211 [Param Access Lvl] set to option 1 “Advanced”.

Monitor Speed Meters
[Speed Ref A] 44 [Ramp In Pct] 111 [Spd Feedback] 122
Monito
[Speed Ref A Pct] 47 [Ramp Out] 113 [Spd Feedback Pct] 121
r
[Speed Ref B] 48 [Ramp Out Pct] 114 [Actual Speed] 924
[Speed Ref B Pct] 49 [Speed Draw Out] 1018 [Encoder Speed] 420
[Speed Ref Out] 385 [Spd Draw Out Pct] 1019 [Tachometer Speed] 1408
[Spd Ref Out Pct] 384 [Speed Reg In] 118
[Ramp In] 110 [Speed Reg In Pct] 117
Current Meters [Spd Reg Out Pct] 236 [Field Current] 351 [Filt TorqCur Pct] 928
[Current Reg In] 41 [Fld Current Pct] 234 [Field Ref Pct] 500
[Arm Current] 200 [Cur Lim Pos Out] 10
[Arm Current Pct] 199 [Cur Lim Neg Out] 11
Drive Data [FaultCode] 57 [Output Voltage] 233 [Drive Size] 465
[AC Line Voltage] 466 [Output Power] 1052 [Elapsed Lifetime] 235
[AC Line Freq] 588 [Drive Type] 300 [Software Version] 331
Motor Control Motor Data [Max Ref Speed] 45 [Nom Mtr Arm Amps] 179 [Drive Type Sel] 201
Motor
Contr
[Max Feedback Spd] 162 [Nom Mtr Fld Amps] 280
ol
[Rated Motor Volt] 175 [Drv Fld Brdg Cur] 374
Field Config [Field Reg Enable] 497 [Fld Weaken Ratio] 456 [Fld Reg Ki Base] 98
[Field Economy En] 499 [Fld Reg Kp] 91 [Set Fld Curve] 919
[Field Econ Delay] 1407 [Fld Reg Ki] 92 [Reset Fld Curve] 920
[Field Mode Sel] 469 [Force Min Field] 498 [Fld Const 40 Pct] 916
[Max Fld Curr Pct] 467 [Out Volt Level] 921 [Fld Const 70 Pct] 917
[Min Fld Curr Pct] 468 [Fld Reg Kp Base] 97 [Fld Const 90 Pct] 918
Torq Attributes [Current Limit] 7 [Torque Reduction] 342 [TrqTpr_Lim2] 753
[Current Lim Pos] 8 [Zero Torque] 353 [TrqTpr_Lim3] 754
[Current Lim Neg] 9 [TrqTpr_Enable] 750 [TrqTpr_Lim4] 755
[Torque Ref] 39 [TrqTpr_Lim0] 751 [TrqTpr_Spd] 756
[Trim Torque] 40 [TrqTpr_Lim1] 752 [Filt Torq Cur] 926
Speed Feedback [Fdbk Device Type] 414 [Spd Fdbk Error] 455 [Z Channel Enable] 911
[Anlg Tach Gain] 562 [Act Spd Filter] 923 [Z Capture Pos En] 912
[Anlg Tach Zero] 563 [Encoder PPR] 169 [Z Captured Pos] 913
[Spd Fdbk Control] 457 [Encoder Out Sel] 1021
[SpdReg FB Bypass] 458 [Encoder Err Chk] 652
Autotune [Autotune Cur Lim] 1048 [Speed Tune Dir] 1029 [I Reg Error] 587
[CurrReg Autotune] 452 [Speed Tune Kp] 1032 [Inertia C Filter] 1012
[Arm Resistance] 453 [Speed Tune Ki] 1033 [Torque Const] 1013
[Arm Inductance] 454 [Spd Tune Inertia] 1030 [Inertia] 1014
[Spd Reg Autotune] 1027 [SpdTune Friction] 1031 [Friction] 1015
Test Generator [TstGen Output] 58 [TstGen Amplitude] 60 [TstGen Offset] 61
[TstGen Frequency] 59
Speed Command Limits [Minimum Speed] 1 [Min Speed Rev] 6 [Max Speed Fwd] 3
Speed
Comm
[Min Speed Fwd] 5 [Maximum Speed] 2 [Max Speed Rev] 4
and
Discrete Speeds [Jog Speed] 266 [Preset Speed 3] 156 [Preset Speed 7] 160
[Jog Off Delay] 1409 [Preset Speed 4] 157 [TB Manual Ref] 267
Speed [Trim Ramp] 42 [Trim Speed] 43 [Speed Ratio] 1017
References [Trim Ramp Pct] 378 [Trim Speed Pct] 379
Speed Regulator [Speed Reg En] 242 [Speed Thresh Neg] 102 [Flying Start En] 388
[Arm Volt Kp] 493 [Threshold Delay] 103 [Spd Fdbk Filter] 444
[Arm Volt Ki] 494 [At Speed Error] 104 [Spd Up Gain Pct] 445
[Spd Reg Kp] 87 [At Speed Delay] 105 [Speed Up Base] 446
[Spd Reg Ki] 88 [Ref Zero Level] 106 [Speed Up Filter] 447
[Arm Volt Kp Base] 495 [Speed Zero Level] 107 [SpdReg Kp Bypass] 459
[Arm Volt Ki Base] 496 [Speed Zero Delay] 108 [SpdReg Ki Bypass] 460
[Spd Reg Kp Base] 93 [Spd Zero I En] 123 [SpdFuncSelect] 1016
[Spd Reg Ki Base] 94 [Spd Ref Zero En] 124 [InertiaCompAct] 1191
[Spd Reg Kp Outpt] 99 [Spd Zero P En] 125 [InertiaCompVar] 1192
[Spd Reg Ki Outpt] 100 [Spd Zero P Gain] 126
[Speed Thresh Pos] 101 [Lock Speed Integ] 348


Dynamic Control Ramp Rates [Speed Ramp En] 245 [MOP Decel Time] 30 [Ramp Delay] 20
[Ramp Type Select] 18 [Jog Ramp Time] 1410 [Zero Ramp Output] 344
Dynam
ic Con
trol
[Accel Time 1] 660 [S Curve Time] 19 [Zero Ramp Input] 345
[Decel Time 1] 662 [S Curve Accel 1] 665 [Freeze Ramp] 373
[Accel Time 2] 24 [S Curve Decel 1] 666 [Acc Dec Filter] 1212
[Decel Time 2] 32 [S Curve Accel 2] 667
[MOP Accel Time] 22 [S Curve Decel 2] 668
Load Limits [Enable Droop 699 [Droop Limit] 700 [Torq Limit Type] 715
[Droop Percent] 696 [Load Comp] 698
[Droop Filter] 697 [Torq Red CurLim] 13
Stop Modes [Fast Stop Time] 38 [Closing Speed] 1262 [Ramp In Zero En] 1265
[Spd 0 Trip Delay] 627 [Opening Delay] 1263 [Actuator Delay] 1266
Restart Modes [Start At Powerup] 1344 [Powerup Delay] 1345
Adaptv Regulator [Adaptive Spd En] 181 [Adaptive Joint 1] 186 [Adaptive I Gain2] 191
[Adaptive Reg Typ] 182 [Adaptive Joint 2] 187 [Adaptive P Gain3] 192
[Adaptive Ref] 183 [Adaptive P Gain1] 188 [Adaptive I Gain3] 193
[Adaptive Spd 1] 184 [Adaptive I Gain1] 189
[Adaptive Spd 2] 185 [Adaptive P Gain2] 190


Applications PI Control [Enable PI] 769 [PI Central v1] 776 [PI Central vs1] 781
Applic
atio
[PI Steady Thrsh] 695 [PI Central v2] 777 [PI integr freeze] 783
ns
[PI Integral Gain] 764 [PI Central v3] 778 [PI Upper Limit] 784
[PI Prop Gain PID] 765 [PI Central v sel] 779 [PI Lower Limit] 785
[PI Output] 771 [PI Central vs0] 780 [PI Init Prop Gn] 793
PD Control [Enable PD] 770 [PD Deriv Filter] 767 [PD Deriv Gain 2] 789
[PD Output PID] 421 [PD Prop Gain 1] 768 [PD Prop Gain 3] 790
[PD Deriv Gain 1] 766 [PD Prop Gain 2] 788 [PD Deriv Gain 3] 791
PID Control [Enable PID] 1258 [PID Setpoint 0] 760 [PID Target] 782
[Real FF PID] 418 [PID Setpoint 1] 761 [PID Source] 786
[PID Steady Delay] 731 [PID Setpoint Sel] 762 [PID Source Gain] 787
[PI Init Intgl Gn] 734 [PID Feedback] 763 [PID Accel Time] 1046
[PID Clamp] 757 [PID Output Sign] 772 [PID Decel Time] 1047
[Feed Fwd PID] 758 [PID Output Scale] 773 [PID Error Gain] 1254
[PID Error] 759 [PID Output] 774
Scale Blocks [Scale1 Input] 484 [Scale3 Input] 1218 [Scale5 Input] 1236
[Scale1 Output] 485 [Scale3 Output] 1219 [Scale5 Output] 1237
[Scale1 Mul] 486 [Scale3 Mul] 1220 [Scale5 Mul] 1238
[Scale1 Div] 487 [Scale3 Div] 1221 [Scale5 Div] 1239
[Scale1 In Max] 488 [Scale3 In Max] 1222 [Scale5 In Max] 1240
[Scale1 In Min] 489 [Scale3 In Min] 1223 [Scale5 In Min] 1241
[Scale1 In Off] 490 [Scale3 In Off] 1224 [Scale5 In Off] 1242
[Scale1 Out Off] 491 [Scale3 Out Off] 1225 [Scale5 Out Off] 1243
[Scale1 In Abs] 492 [Scale3 In Abs] 1226 [Scale5 In Abs] 1244
[Scale2 Input] 553 [Scale4 Input] 1227 [Scale6 Input] 1245
[Scale2 Output] 554 [Scale4 Output] 1228 [Scale6 Output] 1246
[Scale2 Mul] 555 [Scale4 Mul] 1229 [Scale6 Mul] 1247
[Scale2 Div] 556 [Scale4 Div] 1230 [Scale6 Div] 1248
[Scale2 In Max] 557 [Scale4 In Max] 1231 [Scale6 In Max] 1249
[Scale2 In Min] 558 [Scale4 In Min] 1232 [Scale6 In Min] 1250
[Scale2 In Off] 559 [Scale4 In Off] 1233 [Scale6 In Off] 1251
[Scale2 Out Off] 560 [Scale4 Out Off] 1234 [Scale6 Out Off] 1252
[Scale2 In Abs] 561 [Scale4 In Abs] 1235 [Scale6 In Abs] 1253
Diameter Calc [Diameter Calc] 794 [Line Spd Thresh] 1155 [Diam Preset 0] 1164
[DncrPosSpd] 795 [Line Spd Gain] 1156 [Diam Preset 1] 1165
[Max Deviation] 796 [Diameter Reset] 1157 [Diam Preset 2] 1166
[Gear Box Ratio] 797 [Diam Threshold] 1158 [Diam Preset 3] 1167
[Dancer Constant] 798 [Diameter Reached] 1159 [Diam Preset Sel] 1168
[Minimum Diameter] 799 [Line Speed Pct] 1160 [Diam Inc Dec En] 1205
[Diameter Calc St] 800 [Diam Calc Dis] 1161 [Diam init filter 1206
[Max Diameter] 1153 [Diameter Filter] 1162 [Diam stdy delay] 1207
[Roll Diameter] 1154 [Base Omega] 1163
Winder Functions [Variable J Comp] 1171 [Line FastStp Pct] 1186 [Torque Winder En] 1209
[Constant J Comp] 1172 [Winder Type] 1187 [W Target] 1210
[Materl Width Pct] 1173 [Torq Current Pct] 1193 [Actual Comp] 1213
[Static Friction] 1174 [Act Ten Ref Pct] 1194 [Closed Loop En] 1214
[Dynamic Friction] 1175 [Speed Match] 1195 [Speed Demand En] 1215
[Taper Enable] 1176 [Spd Match Acc] 1196 [Spd match torque] 1216
[Initial Diameter] 1177 [Spd Match Dec] 1197 [W Reference] 1217
[Final Diameter] 1178 [Offs Accel Time] 1198 [Jog TW Speed] 1255
[Tension Reduct] 1179 [W Offset] 1199 [Jog TW Enable] 1256
[Tension Ref] 1180 [Spd Match Gain] 1200 [Ref Spd Source] 1284
[Tension Scale] 1181 [Winder Side] 1201 [Ref Speed Gain] 1285
[Time AccDec Min] 1182 [W Gain] 1202 [Ref Line Speed] 1286
[Int Acc Calc En] 1183 [Spd Match Compl] 1203 [Static F Zero] 1287
[Line Accel Pct] 1184 [Line Spd Source] 1204
[Line Decel Pct] 1185 [Close Loop Comp] 1208


Utility Reference Config [Direction Mode] 1322 [Man Ref Preload] 210 [MOP Select] 1375
Utility
[Save HIM Ref] 209 [Save MOP Ref] 249
Drive Memory [Param Access Lvl] 211 [Reset Defaults] 258
Diagnostics [Drive Status 1] 381 [Torque Positive] 346 [Accel Status] 1188
[Drive Status 2] 382 [Torque Negative] 347 [Decel Status] 1189
[Last Stop Source] 1402 [MOP Inc Active] 396 [Fast Stop Status] 1190
[Start Inhibits] 1403 [MOP Dec Active] 397 [TestPoint Sel] 1381
[Drive Logic Rslt] 1328 [Spd Select 0] 400 [TestPoint Data] 1382
[At Speed] 394 [Spd Select 1] 401 [TaskLoad 32 ms] 1383
[At Zero Speed] 395 [Spd Select 2] 402 [TaskLoad 1 ms] 1384
[CurrLimit Active] 349 [Ramp Select 0] 403 [TaskLoad 2 ms] 1385
[Spd Limit Active] 372 [Ramp Select 1] 404 [TaskLoad 8 ms] 1386
[Speed Threshold] 393 [Encoder State] 651
Faults [Clear Fault Que] 263 [Fault 2 Code] 1352 [Fault 2 Time] 1362
[Fault Clear] 1347 [Fault 3 Code] 1353 [Fault 3 Time] 1363
[Fault Clr Mode] 1348 [Fault 4 Code] 1354 [Fault 4 Time] 1364
[Status1 at Fault] 1349 [Fault 5 Code] 1355 [Fault 5 Time] 1365
[Status2 at Fault] 1350 [Fault 6 Code] 1356 [Fault 6 Time] 1366
[Fault Arm Amps] 1371 [Fault 7 Code] 1357 [Fault 7 Time] 1367
[Fault Speed] 1372 [Fault 8 Code] 1358 [Fault 8 Time] 1368
[Fault Field Amps] 1373 [Fault 9 Code] 1359 [Fault 9 Time] 1369
[Fault Voltage] 1374 [Fault 10 Code] 1360 [Fault 10 Time] 1370
[Fault 1 Code] 1351 [Fault 1 Time] 1361
Alarms [Drive Alarm 1] 1380 [OverTemp Flt Cfg] 365 [UnderVolt Thresh] 481
[OverVolt Flt Cfg] 203 [FldLoss Flt Cfg] 473 [OverCurrent Thr] 584
[Aux Inp Flt Cfg] 354 [Spd Loss Flt Cfg] 478
User Defined [UsrDsplyMult0] 50 [UserDefined14] 517 [UsrDefBitWrdA15] 535
[UsrDsplyDiv0] 51 [UserDefined15] 518 [UsrDefBitWrdB] 536
[UsrValMult1] 53 [UsrDefBitWrdA] 519 [UsrDefBitWrdB0] 537
[UsrValDiv1] 54 [UsrDefBitWrdA0] 520 [UsrDefBitWrdB1] 538
[UserDefined0] 503 [UsrDefBitWrdA1] 521 [UsrDefBitWrdB2] 539
Communications Comm Control [DPI Baud Rate] 589 [DPI Fdbk Select] 1321 [DPI Port Value] 1343
Comm
[DPI Port Sel] 590
unicat
ion
Masks & Owners [Logic Mask] 591 [MOP Mask] 598 [Reference Owner] 604
[Start Mask] 592 [Local Mask] 599 [Accel Owner] 605
[Jog Mask] 593 [Decel Mask] 631 [Fault Clr Owner] 606
[Direction Mask] 594 [Stop Owner] 600 [MOP Owner] 607
[Reference Mask] 595 [Start Owner] 601 [Local Owner] 608
[Accel Mask] 596 [Jog Owner] 602 [Decel Owner] 609
[Fault Clr Mask] 597 [Direction Owner] 603
Datalinks [Data In A1] 610 [Data In D1] 616 [Data Out C1] 622
[Data In A2] 611 [Data In D2] 617 [Data Out C1] 623
[Data In C1] 614 [Data Out B1] 620 [Data In Val Sel] 1319
[Data In C2] 615 [Data Out B2] 621 [Data In SelData] 1320
Security [Logic Mask] 591 [Write Mask Act] 1377 [Port Mask Act] 1379
[Logic Mask Act] 1376 [Write Mask Cfg] 1378


Input / Output Analog Inputs [Anlg In1 Sel] 70 [Anlg2 Tune Scale] 78 [Anlg In2 Target] 296
Inputs
/ Outpu
[Anlg In1 Config] 71 [Anlg In2 Offset] 79 [Anlg In3 Target] 297
ts
[Anlg In1 Scale] 72 [Anlg In2 Tune] 260 [Anlg In1 Cmp] 1042
[Anlg1 Tune Scale] 73 [Anlg In3 Sel] 80 [Anlg In1 Cmp Err] 1043
[Anlg In1 Offset] 74 [Anlg In3 Config] 81 [Anlg In1 Cmp Dly] 1044
[Anlg In1 Tune] 259 [Anlg In3 Scale] 82 [Anlg In1 Cmp Eq] 1045
[Anlg In1 Filter] 792 [Anlg3 Tune Scale] 83 [Analog In1 Value] 1404
[Anlg In2 Sel] 75 [Anlg In3 Offset] 84 [Analog In2 Value] 1405
[Anlg In2 Config] 76 [Anlg In3 Tune] 261 [Analog In3 Value] 1406
[Anlg In2 Scale] 77 [Anlg In1 Target] 295
Analog Outputs [Anlg Out1 Sel] 66 [Anlg Out4 Sel] 69 [Analog Out3 Scale] 64
[Anlg Out2 Sel] 67 [Analog Out1 Scale] 62 [Analog Out4 Scale] 65
[Anlg Out3 Sel] 68 [Analog Out2 Scale] 63
Digital Inputs [ContactorControl] 1391 [Digital In12 Sel] 144 [Dig In Term 1] 565
[Dig In Status] 564 [Inversion In 1] 1276 [Dig In Term 2] 566
[Digital In1 Sel] 133 [Inversion In 2] 1277 [Dig In Term 3] 567
[Digital In11 Sel] 143 [Inversion In 12] 1390
Digital Outputs [Dig Out Status] 581 [Digital Out7 Sel] 151 [Inversion Out 4] 1270
[Digital Out1 Sel] 145 [Digital Out8 Sel] 152 [Inversion Out 5] 1271
[Digital Out2 Sel] 146 [Relay Out 1 Sel] 1392 [Inversion Out 6] 1272
[Digital Out3 Sel] 147 [Relay Out 2 Sel] 629 [Inversion Out 7] 1273
[Digital Out4 Sel] 148 [Inversion Out 1] 1267 [Inversion Out 8] 1274
[Digital Out5 Sel] 149 [Inversion Out 2] 1268 [Inversion Relay1] 1393
[Digital Out6 Sel] 150 [Inversion Out 3] 1269 [Inversion Relay2] 1275
DPI Inputs [DPI P1 Select] 1323 [DPI P3 Select] 1325 [DPI P5 Select] 1327
[DPI P2 Select] 1324 [DPI P4 Select] 1326

Monitor File
Related
Group
Parameter Name & Description

File
No. See page 3-2 for symbol descriptions Values

44 [Speed Ref A] Default: Read Only 45
First speed reference for the drive. Negative values apply to four Min/Max: –/+ Par 45 [Max Ref Speed] (1)
quadrant drives only. Units: RPM

Note: This parameter is assigned to analog input 1 (terminals 1 (1)
The value of [Max Ref Speed] cannot exceed 8192 RPM.
& 2, Par 70 [Anlg In1 Sel]) by default, but can be assigned to any
analog input.
47 [Speed Ref A Pct] Default: Read Only 45
First speed reference for the drive as a percentage of the value Min/Max: –/+100.00
defined in Par 45 [Max Ref Speed]. Units: %
48 [Speed Ref B] Default: Read Only 45
Second speed reference for the drive. Negative values apply to Min/Max: –/+ Par 45 [Max Ref Speed] (1)
four quadrant drives only. Units: RPM

Note: This parameter can be assigned to an analog input. (1)
The value of [Max Ref Speed] cannot exceed 8192 RPM.
49 [Speed Ref B Pct] Default: Read Only 45
The second speed reference for the drive as a percentage of the Min/Max: –/+100.00
value defined in Par 45 [Max Ref Speed]. Units: %
110 [Ramp In] Default: Read Only
Total reference value input to the ramp in RPM. Min/Max: –/+32766
Note: This parameter can be assigned to an analog output. Units: RPM
111 [Ramp In Pct] Default: Read Only 45
Total reference value input to the ramp as a percentage of Par Min/Max: –/+100.00
45 [Max Ref Speed]. Units: %
Note: This parameter can be assigned to an analog output.
113 [Ramp Out] Default: Read Only
Speed Meters
Output of the ramp in RPM. Min/Max: –/+32766

MONITOR

114 [Ramp Out Pct] Default: Read Only 45
Output of the ramp as a percentage of Par 45 [Max Ref Speed]. Min/Max: –/+100.00
Units: %
117 [Speed Reg In Pct] Default: Read Only
Total reference value input to the Speed Regulator as a Min/Max: –/+100.00
percentage of Par 45 [Max Ref Speed]. Units: %
118 [Speed Reg In] Default: Read Only
Total reference value input to the Speed Regulator in RPM. Min/Max: –/+32766
121 [Spd Feedback Pct] Default: Read Only 45,
Actual speed as a percentage of the Par 45 [Max Ref Speed]. Min/Max: –/+100.00 923
Note: This parameter is assigned to analog output 1 (terminals Units: %
21 and 22, Par 66 [Anlg Out1 Sel]) by default, but can be
assigned to any analog output.
122 [Spd Feedback] Default: Read Only
Actual speed in RPM. Min/Max: –/+32766
Units: RPM
384 [Spd Ref Out Pct] Default: Read Only 45
Output of the Speed Reference selection as a percentage of Par Min/Max: –/+100.00
385 [Speed Ref Out] Default: Read Only
Output of the Speed Reference selection. Min/Max: –/+32766
Units: RPM
420 [Encoder Speed] Default: Read Only 414
Actual speed measured by the digital encoder. Min/Max: –/+8192
Units: RPM

Related
Group
File
No.
See page 3-2 for symbol descriptions Values
924 [Actual Speed] Default: Read Only 121
Filtered value of Par 122 [Spd Feedback]. Min/Max: –/+32766
1018 [Speed Draw Out] Default: Read Only 45
Speed draw output value. Min/Max: –/+ Par 45 [Max Ref Speed] 1
Speed Meters

(1) The value of [Max Ref Speed] cannot exceed 8192 RPM.
1019 [Spd Draw Out Pct] Default: Read Only 45
Speed value as a percentage of Par 45 [Max Ref Speed]. Min/Max: –/+100.00
Units: %
1408 [Tachometer Speed] Default: Read Only
Actual speed measured by the DC analog tachometer. Min/Max: –/+32770
Units: RPM
10 [Cur Lim Pos Out] Default: Read Only 179
Displays the value of the current limit for the positive torque Min/Max: 0 / 200
direction, expressed as a percentage of the value in Par 179 Units: %
[Nom Mtr Arm Amps].
11 [Cur Lim Neg Out] Default: Read Only 179
Displays the value of the current limit for the negative torque Min/Max: 0 / 200
direction, expressed as a percentage of the value in Par 179 Units: %
[Nom Mtr Arm Amps].
41 [Current Reg In] Default: Read Only 179
Total current reference value expressed as a percentage of the Min/Max: –/+200
value in Par 179 [Nom Mtr Arm Amps]. Units: %
MONITOR
199 [Arm Current Pct] Default: Read Only 179

Armature current expressed as a percentage of the value in Par Min/Max: –/+250
179 [Nom Mtr Arm Amps]. Units: %
Note: This parameter is assigned to analog output 2 (Terminals
23 and 24, Par 67 [Anlg Out2 Sel]) by default, but can be
assigned to any analog output.
200 [Arm Current] Default: Read Only
Current Meters
Armature current in Amperes. Min/Max: –/+2.5 x [Nom Mtr Arm Amps]

Units: A
234 [Fld Current Pct] Default: Read Only 280
Field current (present value) as a percentage of Par 280 [Nom Min/Max: 0.00 / 100.00
Mtr Fld Amps]. Units: %
236 [Spd Reg Out Pct] Default: Read Only 39
Output value of the speed regulator used as the reference for Min/Max: –/+200
the current regulator. Units: %
Note: By default, this parameter is linked to Par 39 [Torque Ref].
351 [Field Current] Default: Read Only
Present value of the field current. The value of this parameter Min/Max: 0.00 / 99.90
equals the value of Par 468 [Min Fld Curr Pct] when Par 499 Units: A
[Field Economy En] = 1 “Enabled” and Field Economy becomes
active.
500 [Field Ref Pct] Default: Read Only 280
Field current (reference) as a percentage of Par 280 [Nom Mtr Min/Max: 0.00 / 100.00
Fld Amps]. Units: %
928 [Filt TorqCur Pct] Default: Read Only 1193
Percent filtered value of Par 199 [Arm Current Pct]. Min/Max: –/+200
Note: This parameter can be assigned to an analog output. Units: %

Related
Group
File
No.
57 [FaultCode] Default: Read Only
A code that represents the fault that tripped the drive. Refer to Min/Max: 0 / 65535
Fault Descriptions on page 4-4 for a list of fault codes and
descriptions.
233 [Output Voltage] Default: Read Only
Armature Voltage UdA in VAV. Min/Max: -/+999.00
Note: This parameter can be assigned to an analog output. Units: Vdc
235 [Elapsed Lifetime] Default: Read Only
Shows the operating time of the drive. This parameter counts Min/Max: 0.00 / 65540.00
the time for which the drive is energized (even if the drive is Units: H.m
disabled).
300 [Drive Type] Default: Read Only
Displays of the drive type. Min/Max: 10 / 11
“10” = Non-Regenerative
“11” = Regenerative
Drive Data
MONITOR
331 [Software Version] Default: Read Only

Displays the software version number active in the drive. Min/Max: 1.00 / 999.00
465 [Drive Size] Default: Read Only
Armature current rating (as indicated by the configuration of DIP Min/Max: 0 / Based on drive current rating
switch S15 on the Control board). Units: A
Note: S15 is set to the appropriate value at the factory. However,
if the Control board was supplied as a replacement part, S15
must be manually set to the appropriate drive size. Refer to DIP
Switch and Jumper Settings on page 1-32.
466 [AC Line Voltage] Default: Read Only
AC input voltage. Min/Max: 0 / 960
Units: Vac
588 [AC Line Freq] Default: Read Only
AC input frequency. Min/Max: 0.00 / 70.00
Units: Hz
1052 [Output Power] Default: Read Only
Output power. Min/Max: 0.00 / 9999.99
Note: This parameter can be assigned to an analog output. Units: kW

Motor Control File
Related
Group

File
No.

45 [Max Ref Speed] Default: 1750
Maximum reference speed as determined by the application. If Min/Max: 1 / 16383
Field Weakening is not required, this value will be equal to the Units: RPM
Motor Nameplate Base Speed (RPM). The value of this
parameter is used to scale all of the other speed reference
related parameters.
162 [Max Feedback Spd] Default: 1750.00 162,
Maximum feedback speed as determined by the application. If Min/Max: 1.00 / 6553.00 175
Field Weakening is not used, the value of this parameter will be Units: RPM
equal to the Motor Nameplate base speed. This value must be
at least 10% lower than the Motor nameplate maximum safe
speed (in order to allow an “Overspeed” fault to occur). The
value in this parameter is also used to convert tachometer and
armature feedback values to rpm. When armature voltage
feedback is used, the value of Par 175 [Rated Motor Volt] is
considered equivalent to Par 162 [Max Feedback Spd].
Therefore, this parameter should be set appropriately.
175 [Rated Motor Volt] Default: 500.00 469
Maximum armature voltage of the drive. Typically, this value is Min/Max: 20.00 / 999.00
set to the Motor Nameplate Armature voltage. When Par 469 Units: V
[Field Mode Sel] is set to 1 = “Field Weaken”, the value in this
Motor Data
parameter equals the voltage that begins the weakening phase

of the field.
Note: This parameter affects the threshold of an overvoltage
condition, as indicated by an “Arm Overvoltage” fault (F5).
MOTOR CONTROL
179 [Nom Mtr Arm Amps] Default: Based on drive current rating
Rated motor nameplate armature current. The settings for the Min/Max: 0.10 / Based on drive current rating
current limit and the overload function are based on this current Units: A
value.
201 [Drive Type Sel] Default: 0= “Off”
This parameter is only applicable to non-regenerative Options: 0= “Off”
(2-quadrant) drives. It allows non-regenerative drives to use an 1= “On”
A external 4-quadrant controller.
• “On” = Ramp, Speed, Torque current references and Speed
measurement have the same behavior of a four quadrant
drive.
280 [Nom Mtr Fld Amps] Default: Par 374 [Drv Fld Brdg Cur] x 0.33
Rated motor nameplate field current (IdFN). Min/Max: 0.00 / [Drv Fld Brdg Cur]
Units: A
374 [Drv Fld Brdg Cur] Default: 1.00
Drive rated field bridge current (IdFN). The value in this field must Min/Max: 0.50 / 80.00
be set equal to the value chosen with DIP switch S14 on the Units: A
Control board (refer to Table 1.G on page 1-25 for DIP switch
configuration).
91 [Fld Reg Kp] Default: 2.00 97
Proportional gain (KP) of the flux regulator expressed as a Min/Max: 0.00 / 100.00
A percentage of Par 97 [Fld Reg Kp Base]. Units: %
92 [Fld Reg Ki] Default: 1.00 98
Field Config
Integral gain (KI) of the flux regulator expressed as a percentage Min/Max: 0.00 / 100.00
A of Par 98 [Fld Reg Ki Base]. Units: %
97 [Fld Reg Kp Base] Default: 3277.00
The proportional gain (KP0) of the field current regulator (base Min/Max: 0.10 / 32770.00
value).
A

Related
Group
File
No.
98 [Fld Reg Ki Base] Default: 3277.00
Integral gain (KI0) of the field current regulator in (base value). Min/Max: 0.10 / 32770.00
A
456 [Fld Weaken Ratio] Default: 100
The ratio of Motor Nameplate Base Speed to Par 45 [Max Ref Min/Max: 0 / 100
Speed] when Par 469 [Field Mode Sel] = 1 "Field Weaken". It is Units: %
the percentage of maximum application speed when field
weakening will begin. This value is "Motor Base Speed" / Par 45
[Max Ref Speed] x 100. If Par 469 [Field Mode Sel] = 0 “Base
Speed”, this parameter must be = 100%.
467 [Max Fld Curr Pct] Default: 100 468
Maximum allowable field current. The maximum value (100%) Min/Max: Par 468 [Min Fld Curr Pct] / 100
corresponds to the value set in Par 280 [Nom Mtr Fld Amps]. Units: %
The value of this field linearly affects the field current, unless a
flux curve is set in Pars 916, 917, and 918 [Fld Const xx Pct].
Note: This parameter can be assigned to an analog input or
output.
468 [Min Fld Curr Pct] Default: 30 467,
Minimum allowable field current. The value set in this parameter Min/Max: 0 / Par 467 [Max Fld Curr Pct] 499
also influences the threshold at which the “Fld Current Loss” Units: %
(F6) fault occurs. The threshold is half of the value of Par 468
[Min Fld Curr Pct]. The value of Par 351 [Field Current] equals
the value of this parameter when Par 499 [Field Economy En] =
MOTOR CONTROL
1 “Enabled” and Field Economy becomes active.

Field Config
469 [Field Mode Sel] Default: 0= “Base Speed” 916,

Operating mode of the field controller. Options: 0= “Base Speed” 917,
• “Base Speed” = The motor field is regulated with constant 1= “Field Weaken” 918
current and controls the motor from zero to base speed. If a 2= “External”
curve is defined through Pars 916, 917 and 918 [Fld Const xx
Pct], this value will change linearly through Par 467 [Max Fld
Curr Pct] (which is a percentage of the nominal flux value set
in Par 280 [Nom Mtr Fld Amps]).
• “Field Weaken” = The motor field is regulated with a
combination of torque and constant power (armature and field
regulation, i.e., field weakening). The maximum armature
voltage is configured in Par 175 [Rated Motor Volt].
• “External” = The motor field power is supplied by an external
rectifier/converter (the drive’s field output is disabled).
497 [Field Reg Enable] Default: 1= “Enabled” 473
Enables/Disables the field regulator. Options: 0= “Disabled”
• “Enabled” = The field regulator is enabled and controlling the 1= “Enabled”
field output.
• “Disabled” = The field regulator is disabled. (i.e., The field
current is zero.) In addition, Par 473 [FldLoss Flt Cfg] should
be set to 0 “Ignore”.
Note: This parameter can be assigned to a digital input.
498 [Force Min Field] Default: 0= “Disabled”
Enables/Disables the minimum field current value. Options: 0= “Disabled”
A • “Enabled” = The field current corresponds to the value set via 1= “Enabled”
Par 468 [Min Fld Curr Pct].
• “Disabled” = The field current is regulated based on the
quadrant mode and situation in which the drive is operating.
Note: This parameter can be assigned to a digital input (35
“Force MinFld”).

Related
Group
File
No.
499 [Field Economy En] Default: 1= “Enabled” 395,
When this parameter is set to 1 = “Enabled” and the value in Par Options: 0= “Disabled” 468
107 [Speed Zero Level] is reached, the minimum field current 1= “Enabled”
(set via Par 468 [Min Fld Curr Pct]) is produced (field economy).
• “Disabled” = Disables the field economy function
• “Enabled” = Enables the field economy function
916 [Fld Const 40 Pct] Default: 40.00 469
Current value at 40% of the field current. Min/Max: 0.00 / 100.00
Units: %
A
Units: %
A
Units: %
A
919 [Set Fld Curve] Default: 1 916,
Field Config
When set to “0”, this parameter controls the motor field current Min/Max: 0/1 917,
to field reference curve according to the values specified in the 918
A [Fld Const xx Pct] parameters. With this curve is defined, the
MOTOR CONTROL
result of [Max Fld Curr Pct] / [Field Ref Pct] equals the
percentage of field current according to the characteristic of the
curve. This field is Write Only. After the value of this field is set to
“0”, it will automatically return to “1”.
920 [Reset Fld Curve] Default: 0
when set to “1”, resets the drive to use a linear field curve. When Min/Max: 0/1
this parameter is set, Par 280 [Nom Mtr Fld Amps] is linearly Units:
A changed through [Max Fld Curr Pct] / [Field Ref Pct]. This field is
Write Only. After the value of this field is set to “1”, it will
automatically return to “0”.
921 [Out Volt Level] Default: 100.00
The percentage of maximum output voltage based on the value Min/Max: 0.00 / 100.00
A in Par 175 [Rated Motor Volt]. This parameter allows you to Units: %
change the output voltage at the motor end when the drive is in
"Field Weaken" mode. Typically set to the default value when the
drive is in Field Weakening mode.
Note: This parameter can be assigned to an analog output or
analog input.
1407 [Field Econ Delay] Default: 300
Amount of time to elapse after the drive reaches zero speed (as Min/Max: 0 / 1800
determined by Par 107 [Speed Zero Level]) before field Units: s
economy becomes active.
7 [Current Limit] Default: 150 8,
Symmetrical current limit expressed as a percentage of the Min/Max: 0 / 200 9,
Torq Attributes
value in Par 179 [Nom Mtr Arm Amps]. This value applies to Units: % 179
both current directions for four quadrant drives.
• If Par 7 [Current Limit] is changed, Pars 8 [Current Lim Pos]
and 9 [Current Lim Neg] are set to the same value. If
subsequently changed, the value of Pars 8 [Current Lim Pos]
and/or 9 [Current Lim Neg] override the value of Par 7
[Current Limit].

Related
Group
File
No.
8 [Current Lim Pos] Default: 150 7
The drive current limit for the positive current direction Min/Max: 0 / 200
expressed as a percentage of the value in Par 179 [Nom Mtr Units: %
Arm Amps].
Note: This parameter can be assigned to an analog input.
9 [Current Lim Neg] Default: 150 7
The drive current limit for the negative current direction Min/Max: 0 / 200
expressed as a percentage of the value in Par 179 [Nom Mtr Units: %
Arm Amps]. This parameter is not active for two quadrant drives.
39 [Torque Ref] Default: 0
First current reference value, before any trim signals are Min/Max: – / +200
incorporated, as a percentage of the value set in Par 179 [Nom Units: %
Mtr Arm Amps]. This parameter is only used when Par 242
[Speed Reg En] = 0 "Disabled".
Note: The current reference value is proportional to the
armature current of the motor and determines the torque. The
polarity determines the torque direction.
40 [Trim Torque] Default: 0
MOTOR CONTROL
Second current reference value as a percentage of the value set Min/Max: – / +200
Torq Attributes
in Par 179 [Nom Mtr Arm Amps]. [Trim Torque] is added to Units: %
Torque Reference and can be used as a correction value for the
torque reference (regardless of the value of Par 242 [Speed Reg
En]).
342 [Torque Reduction] Default: 0= “Not Active” 13
Selection for torque reduction. When the torque reduction Options: 0= “Not Active”
function is active (1 “Active”), the current limit changes 1= “Active”
accordingly by the percentage defined in Par 13 [Torq Red
CurLim]. When this parameter is set to 0 “Not Active”, torque
reduction is not active.
For example:
Par 7 [Current Limit] (or Pars 8 [Current Lim Pos] and 9
[Current Lim Neg]) = 80 %
Par 13 [Torq Red CurLim] = 70%
If Par 342 [Torque Reduction] = 0 “Not Active”, the current
limit = 80 %
If Par 342 [Torque Reduction] = 1 “Active”, the current limit =
70 %
353 [Zero Torque] Default: 1= “Not Active” 41
Sets the reference value for the armature current (Par 41 Options: 0= “Active”
[Current Reg In]) to zero so that the drive has no torque. 1= “Not Active”
• “Not Active” = Par 41 [Current Reg In] is not set to zero.
• “Active” = Par 41 [Current Reg In] is set zero. The drive has
no torque.

Related
Group
File
No.
750 [TrqTpr_Enable] Default: 0= “Disabled” 751,
Enables/Disables the current/speed function. The current/speed Options: 0= “Disabled” 752,
function allows you to change the current limits set in Pars 8 1= “Enabled” 753,
[Current Lim Pos] and 9 [Current Lim Neg] by setting up to five 754,
A 755,
setpoints using parameters [TrqTpr_Limx] and a threshold
speed in Par 756 [TrqTpr_Spd]. 756
• “Disabled” = The limits current /speed curve is disabled
• “Enabled” = The limits current /speed curve is enabled
Par 10 [Cur Lim Pos Out]
or
Par 11 [Cur Lim Neg Out]
Current/Speed
TrqTpr_Lim0]
TrqTpr_Lim1]
TrqTpr_Lim2]
TrqTpr_Lim3]
TrqTpr_Lim4]
Par 162 [Max Feedback Spd]

Par 756 [TrqTpr_Spd]
MOTOR CONTROL
Torq Attributes
751 [TrqTpr_Lim0] Default: 0 750,

The current limit of the current/speed curve that operates Min/Max: 0 / 200 756
constantly up to the speed set in Par 756 [TrqTpr_Spd]. The Units: %
A value specified in this parameter overrides the values specified
in Pars 8 [Current Limit Pos] and 9 [Current Lim Neg].
First reduced current limit of the current/speed curve. The value Min/Max: 0 / 200 756
defined in this parameter must be less than the value in Par 751 Units: %
A [TrqTpr_Lim0] and greater than the values in Pars 753
[TrqTpr_Lim2], 754 [TrqTpr_Lim3] and 755 [TrqTpr_Lim4].
Second reduced current limit of the current/speed curve. The Min/Max: 0 / 200 756
value defined in this parameter must be less than the value in Units: %
A Par 752 [TrqTpr_Lim1] and greater than the values in Pars 754
[TrqTpr_Lim3] and 755 [TrqTpr_Lim4].
Third reduced current limit of the current/speed curve. The value Min/Max: 0 / 200 756
A [TrqTpr_Lim2] and greater than the value in Par 755
[TrqTpr_Lim4].
Last reduced current limit of the current/speed curve. The value Min/Max: 0 / 200 756
A [TrqTpr_Lim3]. The drive will operate at this current limit up to
the value set in parameter 162 [Max Feedback Spd].
756 [TrqTpr_Spd] Default: 0 750,
Threshold speed at which torque reduction begins, as Min/Max: 0 / Par 162 756
determined by the current/speed curve. Units: RPM
A

Related
Torq Attributes Group
File
No.
926 [Filt Torq Cur] Default: 0.100 1193
First rate low-pass filter for Par 1193 [Torq Current Pct]. Min/Max: 0.001 / 0.250
A Units: s
169 [Encoder PPR] Default: 1024.00 162

Number of pulses per revolution of the digital encoder. The Min/Max: 100.00 / 32770.00
value of Pars 169 [Encoder PPR] and 162 [Max Feedback Spd]
A must be set as indicated in Speed Feedback on page C-15.
414 [Fdbk Device Type] Default: 3= “Armature”

The source of speed feedback. Options: 1= “Encoder”
• 1 “Encoder” = Digital encoder 2= “DC Tach”
• 2 “DC Tach” = DC analog tachometer 3= “Armature”
• 3 “Armature” = Internal measurement of the armature voltage
455 [Spd Fdbk Error] Default: 22
The maximum allowable speed feedback error expressed as a Min/Max: 0 / 100
A percentage of the maximum output voltage set in Par 175 Units: %
[Rated Motor Volt]. By means of Par 175 [Rated Motor Volt], Par
456 [Fld Weaken Ratio] and the motor nominal speed, a
relationship between motor speed and armature voltage is
obtained. If the difference is higher than the value set in Par 455
[Spd Fdbk Error], an “Encoder Loss” fault (F91) occurs.
457 [Spd Fdbk Control] Default: 1= “Enabled” 455
Enables/Disables speed feedback control. This function controls Options: 0= “Disabled”
the speed feedback, where a comparison is made between the 1= “Enabled”
MOTOR CONTROL
armature voltage and the speed value read by the encoder or

tachometer. When the value set in Par 455 [Spd Fdbk Error] is
signaled, the fault message “Encoder Loss” (F91) displays. This
Speed Feedback
function is automatically disabled when the armature feedback

has been selected (Par 414 [Fdbk Device Type] = 3 “Armature”).
ATTENTION: If speed feedback control is disabled (Par 457 [Spd Fdbk Control] set to 0
“Disabled” and Par 414 [Device Type] is set to 1 “Encoder”, the motor could run at excessive
! speed or become damaged, which could result in personal injury or destruction of equipment.
458 [SpdReg FB Bypass] Default: 0= “Disabled” 478

Enables/Disables an automatic switch to armature feedback Options: 0= “Disabled”
when the “Encoder Loss” (F91) fault occurs due to an encoder 1= “Enabled”
or tachometer feedback loss. When this parameter is set to
“Enable”, Par 478 [Spd Loss Flt Cfg] must be set to 1 “Alarm”.
After an automatic switch to armature feedback, the speed
regulator works with Pars 459 [SpdReg Kp Bypass] and 460
[SpdReg Ki Bypass] and the D derivative part of the speed
regulator is automatically excluded. Pars [SpdReg Kp Bypass]
and [SpdReg Ki Bypass] must be properly tuned. An automatic
switch to armature feedback can only be accomplished when
running the motor with constant field current.
562 [Anlg Tach Gain] Default: 1.00
Fine scaling of the speed feedback received from the DC analog Min/Max: 0.90 / 3.00
tachometer (Par 414 [Fdbk Device Type] = 2 “DC Tach”). The
voltage feedback value received from the tachometer is
multiplied by this value.
563 [Anlg Tach Zero] Default: 0.00
Offset scaling of the feedback circuit. Min/Max: –/+20.00
Units: RPM

Related
Group
File
No.
652 [Encoder Err Chk] Default: 0 “Disabled” 457
Enables/Disables monitoring of the digital encoder connection Options: 0= “Disabled”
A status. When an alarm is detected, the HIM displays the 1= “Enabled”
“Encoder Loss” (F91) fault. This parameter can be programmed
on a digital output. This function is activated by setting Par 457
[Spd Fdbk Control] = “Enabled”.
911 [Z Channel Enable] Default: 0= “Disabled”
Determines whether the encoder zero pulse (qualification signal Options: 0= “Disabled”
A or “zero cam”) will be read by the drive. This parameter is used 1= “Enabled”
for systems implementing position control.
• “Enabled” = The encoder zero pulse is read.
• “Disabled” = The encoder zero pulse is not read.
Speed Feedback
912 [Z Capture Pos En] Default: 0

Control register of the zero pulse and of the encoder Min/Max: 0 / 6553
A qualification signal.
913 [Z Captured Pos] Default: Read Only
Data and function status register. Min/Max: 0 / 232–1
A
923 [Act Spd Filter] Default: 0.100 121
First order low pass filter time constant for Par 121 [Spd Min/Max: 0.001 / 1.000
A Feedback Pct]. Units: s
1021 [Encoder Out Sel] Default: 0= “Off”
Defines the speed reference to which the encoder signal can be Options: 0= “Off”
input. This parameter is typically set to 0 "Off" and the encoder 1= “Trim Ramp”
A is used for speed feedback only. When set to other than 0 "Off", 2= “Trim Speed”
MOTOR CONTROL
the choice of the speed reference destination must be made 3= “Speed Ref A”
according to the configuration of the speed regulator (for 4= “Speed Ref B”
example "Speed Ref A" cannot be used with an active ramp).
452 [CurrReg Autotune] Default: 0= “Off”
Setting this parameter to 1 “On” and pressing Enter on the HIM Options: 0= “Off”
keypad initiates the current regulator auto tuning procedure. 1= “On”
When the auto tuning procedure is complete, this parameter
automatically resets to 0 “Off”. The resulting armature
resistance and inductance values are set in parameters 453
[Arm Resistance] and 454 [Arm Inductance], respectively.
453 [Arm Resistance] Default: 0.50 452
Motor armature resistance. This parameter can be manually Min/Max: Based on drive current rating
changed to a value other than the value obtained when the Units: Ohm
current regulator auto tuning is completed.
454 [Arm Inductance] Default: 4.00 452
Motor armature inductance. This parameter can be manually Min/Max: Based on drive current rating
Autotune
changed to a value other than the value obtained when the Units: mH
current regulator auto tuning is completed.
587 [I Reg Error] Default: Read Only 452
The auxiliary signal used to determine whether the current Min/Max: –/+80
A regulator is correctly tuned. The value should be as near to zero Units: V
as possible, but values between -/+40 are acceptable.
1012 [Inertia C Filter] Default: 0
First order low–pass filter used to reduce noise caused by the Min/Max: 0 / 1000
A speed differentiation process in the Inertia/Loss compensation Units: ms
block.
1013 [Torque Const] Default: Based on drive current rating
The Motor torque constant used to calculate inertia and friction Min/Max: 0.01 / 99.99
A compensation. The value in this parameter is automatically Units: N–m/A
adapted in the field weakening mode. This value is determined
during speed auto tuning.

Related
Group
File
No.
1014 [Inertia] Default: Based on drive current rating
Motor inertia value. Min/Max: 0.001 / 999.999
A 1 Kg–m2 = 23.76 lb–ft2 Units: Kg–m2
1015 [Friction] Default: Based on drive current rating
Motor friction value. Min/Max: 0.000 / 99.990
A 1 N–m = 0.738 lb–ft Units: N–m
1027 [Spd Reg Autotune] Default: 0= “Ready”
Starts the auto tuning procedure for the speed regulator. Setting Options: 0= “Ready”
this parameter to 1 “On” and pressing Enter on the HIM keypad 1= “Start”
initiates the speed regulator auto tuning procedure. When the
auto tuning procedure is complete, this parameter automatically
resets to 0 “Off”.
1029 [Speed Tune Dir] Default: 1= “Forward”
Choice of the rotation direction of the motor shaft (rotation, as Options: 1= “Forward”
MOTOR CONTROL
seen from the motor shaft side) for the speed regulator auto 2= “Reverse”
tuning procedure.
Autotune
• “Forward” = Clockwise rotation

• “Reverse” = Counter-clockwise rotation
1030 [Spd Tune Inertia] Default: Read Only
Motor inertia value identified during the speed regulator auto Min/Max: 0.00 / 1000.00
tuning procedure. Units: Kg x m2
1031 [SpdTune Friction] Default: Read Only
Motor friction value identified during the speed regulator auto Min/Max: 0.00 / 99.99
tuning procedure. Units: N-m
1032 [Speed Tune Kp] Default: Read Only
Proportional gain value of the speed regulator identified during Min/Max: 0.00 / 100.00
the speed regulator auto tuning procedure.
1033 [Speed Tune Ki] Default: Read Only
Integral gain value of the speed regulator identified during the Min/Max: 0.00 / 100.00
speed regulator auto tuning procedure.
1048 [Autotune Cur Lim] Default: 20
Value of the torque current limit applied during the speed Min/Max: 0 / Based on drive current rating
regulator auto tuning procedure. Units: %

Related
Group
File
No.
58 [TstGen Output] Default: 0= “NotConnected” 59,
Allows you to select a simulated parameter as the output for the Options: 0= “NotConnected” 60,
test generator. The test generator is used to manually tune the 1= “Reserved” 61
A regulators. It consists of a square wave generator whose 2= “Torq Cur Ref”
frequency, offset and amplitude can be manipulated. 3= “Field Ref”
• “NotConnected” - No internal parameters defined by the 4= “Ramp Ref”
generator. 5= “Speed Ref”
• “Reserved” - Not used.
• “Torq Cur Ref” - The output of the generator defines the
reference value of the torque current. 100% corresponds to
“full load torque current” (FLT).
• “Field Ref” - The output of the generator defines the field
reference value. 100% corresponds to the rated field current
based on the motor nameplate data parameters.
• “Ramp Ref” - The output of the generator defines the ramp
reference value. 100% corresponds to the value specified in
Par 45 [Max Ref Speed]. This is the value immediately before
the Ramp function.
• “Speed Ref” - The output of the generator defines the speed
reference value. This is the value immediately before the
Speed Regulator function.
P58
TstGen Output
MOTOR CONTROL
Test Generator
Generator
Output
P60
TstGen Amplitude
P61
TstGen Offset
Time
P59
TstGen Frequency
59 [TstGen Frequency] Default: 0.10 58
Output frequency of the test generator. Min/Max: 0.10 / 62.50
A Units: Hz
60 [TstGen Amplitude] Default: 0.00 58
Amplitude of the delta signal produced by the test generator. Min/Max: 0.00 / 200.00
A Units: %
61 [TstGen Offset] Default: 0.00 58
Offset of the test generator. Min/Max: –/+200.00
A Units: %

Speed Command File
Related
Group

File
No.
1 [Minimum Speed] Default: 0 5,
Defines the minimum speed of the drive. This value applies to both Min/Max: 0 / Par 45 [Max Ref Speed] 6
directions of motor rotation for four quadrant drives. A speed below Units: RPM
the value set in [Minimum Speed] is not possible, regardless of the set
speed reference value. If the value of [Minimum Speed] is changed,
Pars 5 [Min Speed Fwd] and 6 [Min Speed Rev] are set to the same
value. If either Par 5 [Min Speed Fwd] or Par 6 [Min Speed Rev] is
changed later, the last change is valid.
2 [Maximum Speed] Default: 1750 3,
Defines the maximum speed of the drive. This value applies to both Min/Max: 0 / Par 45 [Max Ref Speed] 4
directions of motor rotation for four quadrant drives. The value of this Units: RPM
parameter is input to the speed regulator and therefore takes into
account the reference value that comes from the ramp as well as the
direction of rotation. If the value of [Maximum Speed] is changed,
Pars 3 [Max Speed Fwd] and 4 [Max Speed Rev] are set to the same
value. If either Par 3 [Max Speed Fwd] or Par 4 [Max Speed Rev] is
changed later, the last change is valid.
3 [Max Speed Fwd] Default: 1750 2
Limits
Defines the maximum speed for forward (clockwise) rotation of the Min/Max: 0 / Par 45 [Max Ref Speed]
motor. The value of [Max Speed Fwd] affects the input of the speed Units: RPM
regulator and therefore takes into account both the reference values
that come from the ramp as well as the direction of motor rotation.
4 [Max Speed Rev] Default: 1750 2
SPEED COMMAND
Defines the maximum speed for reverse (counterclockwise) rotation of Min/Max: 0 / Par 45 [Max Ref Speed]
the motor for four quadrant drives only. The value of [Max Speed Rev] Units: RPM
affects the input of the speed regulator and therefore takes into
account both the reference values that come from the ramp as well as
the direction of rotation.
5 [Min Speed Fwd] Default: 0 1
Defines the minimum speed for forward (clockwise) rotation of the Min/Max: 0 / Par 45 [Max Ref Speed]
motor. Speed reference values below the value in this parameter are Units: RPM
clamped until the reference exceeds this limit.
6 [Min Speed Rev] Default: 0 1
Defines the minimum speed for reverse (counterclockwise) rotation of Min/Max: 0 / Par 45 [Max Ref Speed]
the motor for four quadrant drives only. Speed reference values below Units: RPM
the value in this parameter are clamped until the reference exceeds
this limit.
154 [Preset Speed 1] Default: 150
159 [Preset Speed 6]
Discrete Speeds

Default: 1750
Provides an internal fixed speed command value. In bipolar mode,
direction is commanded by the sign of the reference. Min/Max: -32768 / +32767
Note: [Preset Speed 1] cannot be directly selected by the Speed Sel Units: RPM
digital inputs. However, Par 154 [Preset Speed 1] can be directed to
Par 42 [Trim Ramp] via the Scale Block parameters.
266 [Jog Speed] Default: 100
Reference value for jog mode. Min/Max: -/+32767
Note: This parameter can be assigned to an analog input. Units: RPM

Related
Group
File
No.
1409 [Jog Off Delay] Default: 1
Specifies the amount of time that will elapse between removing the Min/Max: 0 - 10
Jog input and commanding the main contactor to open. The amount Units: s
of time specified in [Jog Off Delay] will not begin to elapse until the
measured speed feedback is less than or equal to the value of
Discrete Speeds
parameter 107 [Speed Zero Level]. This delay reduces the wear on
the contactor when repeatedly opening and closing the Jog input over
a short period of time.
Note: This parameter was added with firmware version 2.001.
267 [TB Manual Ref] Default: 0
Reference value for the drive when the Terminal Block asserts Manual Min/Max: –/+ Par 45 [Max Ref Speed] (1)
reference control. Units: RPM
Note: This parameter can be assigned to an analog input. (1) The value of [Max Ref Speed] cannot exceed 8192
RPM.
42 [Trim Ramp] Default: 0 378
This value is added to the speed reference just before the Speed Min/Max: –/+Par 45 [Max Ref Speed] (1)
Ramp function. Units: RPM
The value of Par 45 [Max Ref Speed] cannot exceed
8192 RPM.
43 [Trim Speed] Default: 0 379
This value is added to the speed reference just before the speed Min/Max: –/+ Par 45 [Max Ref Speed] (1)
Speed References
regulator (and after the Speed Ramp function). Units: RPM

The value of Par 45 [Max Ref Speed] cannot exceed
8192 RPM.
378 [Trim Ramp Pct] Default: 0.00 42
SPEED COMMAND
Trim ramp value defined as a percentage of the value defined in Par Min/Max: –/+100.00
379 [Trim Speed Pct] Default: 0.00 43
Trim speed reference value defined as a percentage of the of the Min/Max: –/+100.00
value defined in Par 45 [Max Ref Speed]. Units: %
1017 [Speed Ratio] Default: 10000
Determines the speed ratio value for the Speed-Draw function. Min/Max: 0 / 32767
Note: This value can be input to the drive digitally, or via an analog
input.
87 [Spd Reg Kp] Default: 10.00 93,
Proportional gain of the speed regulator that can be adjusted while Min/Max: 0.00 / 100.00 99
the drive is running. Units: %
88 [Spd Reg Ki] Default: 1.00 94,
Integral gain of the speed regulator that can be adjusted while the Min/Max: 0.00 / 100.00 100
drive is running. Units: %
93 [Spd Reg Kp Base] Default: 0.30 x Par 93max 87,
The proportional gain (KP0) of the speed regulator (base value). Min/Max: 0.01 / Based on drive current rating 99
Speed Regulator
Units: A / RPM
A
94 [Spd Reg Ki Base] Default: 0.30 x Par 94max 88,
The integral gain (KI0) of the speed regulator (base value). Min/Max: 0.01 / Based on drive current rating 100
Units: A/ RPM x ms
A
99 [Spd Reg Kp Outpt] Default: Read Only 87,
Displays the active proportional coefficient of the speed regulator as a Min/Max: 0.00 / 100.00 93
A percentage of the value defined in Par 93 [Spd Reg Kp Base]. Units: %
100 [Spd Reg Ki Outpt] Default: Read Only 88,
Displays the active integral coefficient of the speed regulator as a Min/Max: 0.00 / 100.00 94
A percentage of the value defined in Par 94 [Spd Reg Ki Base]. Units: %

Related
Group
File
No.
101 [Speed Thresh Pos] Default: 1000 393
Threshold speed for the drive above or below which the value of Par Min/Max: 1 / 32767
A 393 [Speed Threshold] changes. When the speed of the drive Units: RPM
exceeds the value of this parameter, Par 393 [Speed Threshold]
displays “Above Thresh” (0). When the speed of the drive is below the
value of this parameter, Par 393 [Speed Threshold] displays “Below
Thresh” (1).
102 [Speed Thresh Neg] Default: 1000 393
Threshold speed for the drive above or below which the value of Par Min/Max: 1 / 32767
A 393 [Speed Threshold] changes. When the speed of the drive Units: PRM
exceeds the value specified in this parameter, Par 393 [Speed
Threshold] displays “Above Thresh” (0). When the speed of the drive
is below this threshold, Par 393 [Speed Threshold] displays “Below
Thresh” (1).
103 [Threshold Delay] Default: 100 393
Amount of time that must elapse before indication that the drive speed Min/Max: 0 / 65535
A is above the value set in Par 101 [Speed Thresh Pos] or below the Units: ms
value set in Par 102 [Speed Thresh Neg].
104 [At Speed Error] Default: 100 394
Defines the speed above and below the speed reference (in Par 118 Min/Max: 1 / 32767
A [Speed Reg In]) at which the value of Par 394 [At Speed] changes. Units: RPM
When the difference between the speed reference and the actual
speed is greater than the value of this parameter, Par 394 [At Speed]
displays “Not Equal” (0). When the difference between the speed
reference and the actual speed is less than the value of this
parameter, Par 394 [At Speed] displays “Equal” (1).
SPEED COMMAND
Speed Regulator
105 [At Speed Delay] Default: 100 394

Amount of time that must elapse before indication that the drive speed Min/Max: 0 / 65535
A reference is within the range specified in Par 104 [At Speed Error] Units: ms
occurs.
106 [Ref Zero Level] Default: 20 123,
Speed below which speed references are equal to zero speed. Switch Min/Max: 1 / 32767 124,
A used in the Speed Zero function. Units: RPM 125,
126
107 [Speed Zero Level] Default: 20 395

Speed below which the actual speed is considered equal to zero. Min/Max: 1 / 32767
A When a Stop command is issued and actual speed goes below this Units: RPM
value, drive output is disabled. The value applies to both rotation
directions for four quadrant drives.
Note: Setting the value of this parameter too low could prevent the
proper functioning of field economy.
Actual Speed Par 107
[Speed Zero Level]
Fwd
Actual Speed = 0
Rev
Par 395
[At Zero Speed]
Par 108 [Speed Zero Delay]
108 [Speed Zero Delay] Default: 100 395

Amount of time that must elapse after the actual speed goes below Min/Max: 0 / 65535
A the value set in Par 107 [Speed Zero Level] before Par 395 [At Zero Units: ms
Speed] changes state.

Related
Group
File
No.
123 [Spd Zero I En] Default: 0= “Disable”
Enables/Disables the output of the integral section of the speed Options: 0= “Disable”
regulator. Used in the Zero Speed function. 1= “Enable”
A • “Enabled” = The output of the integral section of the speed
regulator is set to zero when the speed reference and the speed
feedback are equal to zero. The I component is enabled when a
reference value is entered to restart acceleration.
• “Disabled” = Disables the output of the integral section of the speed
regulator.
124 [Spd Ref Zero En] Default: 0= “Disable”
This parameter is only active when Par 125 [Spd Zero P En] = 1 Options: 0= “Disable”
“Enabled”. Used in the Zero Speed function. 1= “Enable”
A • “Enabled” = The proportional gain, equal to Par 126 [Spd Zero P
Gain] at zero speed, is equal to Par 87 [Spd Reg Kp] when the
speed reference is higher than the value defined in Par 106 [Ref
Zero Level].
• “Disabled” = The proportional gain, equal to Par 126 [Spd Zero P
Gain] at zero speed, is equal to the value in Par 87 [Spd Reg Kp]
when the speed reference or the actual speed is higher than the
value defined in Par 106 [Ref Zero Level].
SPEED COMMAND
125 [Spd Zero P En] Default: 0= “Disable”

Speed Regulator
“Enabled” = When both the speed reference value and the actual Options: 0= “Disable”
speed value = 0, the proportional gain value in Par 126 [Spd Zero P 1= “Enable”
A Gain] is active after the delay time defined in Par 108 [Speed Zero
Delay]. Used in the Zero Speed function.
“Disabled” = The speed regulator keeps its proportional gain
component when the drive is stopped.
126 [Spd Zero P Gain] Default: 10.00
The proportional gain of the speed regulator that is only active when Min/Max: 0.00 / 100.00
A the value of the speed reference and actual speed = 0. This Units: %
parameter is only active when Par 125 [Spd Zero P En] = 1 “Enabled”.
Used in the Zero Speed function.
242 [Speed Reg En] Default: 1= “Enabled” 39,
Enables/Disables the speed regulator output to the torque/current Options: 0= “Disabled” 41,
regulator. 1= “Enabled” 236
• “Enabled” = The speed regulator output is connected to the input of
the torque/current regulator.
• “Disabled” = The speed regulator output is not connected to the
input of the torque/current regulator. Par 39 [Torque Ref] is
connected to the input of the current regulator.
348 [Lock Speed Integ] Default: 1= “Not active”
Enables or disables the integral (I) function of the speed regulator. Options: 0= “Active”
A • “Not active” = The integral component of the speed regulator is 1= “Not active”
enabled.
• “Active” = The integral component of the speed regulator is
disabled.

Related
Group
File
No.
388 [Flying Start En] Default: 0= “Disabled”
Enables/Disables the ability of the drive to connect to a spinning Options: 0= “Disabled”
A motor at actual RPM when a start command is issued. 1= “Enabled”
• “Enabled” = When the drive is turned on, the speed of the motor is
measured and the ramp output is set accordingly. The drive then
runs at the set reference value.
• “Disabled” = When the drive is turned on, the ramp starts from
zero.
Main uses:
•To connect to a motor that is already spinning due to its load (e.g.
in the case of pumps, the flowing medium).
•Re–connection to a spinning motor after a fault or alarm.
Note: If the Flying Start function is disabled, ensure that the motor is
not spinning when the drive is turned on, or harsh motor deceleration
in current limit may occur.
444 [Spd Fdbk Filter] Default: 0 121,
Time constant used by the filter for the Speed Feedback circuit. Min/Max: 0 / 1000 122
A Filtering of the high frequency components of the speed feedback Units: ms
signal is useful in the case of elastic coupling between the motor and
load (i.e., joints or belts).
445 [Spd Up Gain Pct] Default: 0.00
The Speed Up function gain as a percentage of Par 446 [Speed Up Min/Max: 0.00 / 100.00
A Base]. Units: %
446 [Speed Up Base] Default: 1000.00
The Speed Up function maximum gain. This value corresponds to Min/Max: 0.00 / 16000.00
A
SPEED COMMAND
100% of Par 445 [Spd Up Gain Pct]. Units: ms

Speed Regulator
447 [Speed Up Filter] Default: 0

The time constant of the filter for the D (derivative) component of the Min/Max: 0 / 1000
A Speed Up function. Units: ms
459 [SpdReg Kp Bypass] Default: 10.00 458
The proportional gain (KP) of the speed regulator, expressed as a Min/Max: 0.00 / 100.00
A percentage of Par 93 [Spd Reg Kp Base], when an encoder or Units: %
tachometer feedback signal is changed to armature feedback (Par
458 [SpdReg FB Bypass] = “Enabled”).
460 [SpdReg Ki Bypass] Default: 1.00 458
The integral gain (KI) of the speed regulator, expressed as a Min/Max: 0.00 / 100.00
A percentage of Par 94 [Spd Reg Ki Base], when an encoder or Units: %
tachometer feedback signal is changed to armature feedback (Par
458 [SpdReg FB Bypass] = “Enabled”).
493 [Arm Volt Kp] Default: 30.00 495
Proportional gain (KP) of the field voltage regulator expressed as a Min/Max: 0.00 / 100.00
percentage of the value defined in Par 495 [Arm Volt Kp Base]. Units: %
494 [Arm Volt Ki] Default: 40.00 496
Integral gain (KI) of the field voltage regulator expressed as a Min/Max: 0.00 / 100.00
percentage of the value defined in Par 496 [Arm Volt Ki Base]. Units: %
495 [Arm Volt Kp Base] Default: Based on drive current rating 493
The proportional gain (KP0) of the field voltage regulator (base value). Min/Max: 0.10 / Based on drive current rating
Units: A/V
A
496 [Arm Volt Ki Base] Default: Based on drive current rating 494
The integral coefficient (KI0) of the field voltage regulator (base value). Min/Max: 0.01 / Based on drive current rating
Units: A / V / ms
A

Related
Group
File
No.
1016 [SpdFuncSelect] Default: 0= “Speed Up” 444,
Selection of the “Speed Up” or “Inertia/Loss compensation” function. Options: 0= “Speed Up” 445,
Note that these two functions are mutually exclusive - if one is 1= “Inertia/loss” 447,
1012,
A selected, the other is off. 1013,
SPEED COMMAND
Speed Regulator
1014,
1015
1191 [InertiaCompAct] Default: Read Only

A Displays the active compensation of the fixed section as a percentage
of the drive rated current.
Min/Max:
Units:
0.00 / 200.00
%
1192 [InertiaCompVar] Default: Read Only
A Displays the active compensation of the variable section as a
percentage of the drive rated current.
Min/Max:
Units:
0.00 / 200.00
%

Dynamic Control File
Related
Group

File
No.
18 [Ramp Type Select] Default: 0= “Linear”
Determines the type of ramp used. Options: 0= “Linear”
• 0 “Linear” = Linear ramp 1= “S shaped”
• 1 “S shaped” = S–shaped ramp
19 [S Curve Time] Default: 1.00 18,
S-shaped curve time constant. The value of Par 19 [S Curve Time] is Min/Max: 0.10 / 60.00 665,
added to the ramp time of linear ramps, regardless of speed changes. Units: s 666,
If the value of [S Curve Time] is changed, Pars 665 and 667 [S Curve 667,
Accel x] and 666 and 668 [S Curve Decel x] are set to the same value. 668
If any of parameters 665-668 are changed later, the last change is
valid.
S Curve Time
20 [Ramp Delay] Default: 100 113,

Defines a ramp delay time when the ramp is active. Works with par Min/Max: 0 / 65535 346,
A [Digital Outx Sel] set to 6 “Ramp Pos” or 7 “Ramp Neg”. Units: ms 347
DYNAMIC CONTROL
Par 113 [Ramp Out]

Ramp Rates
Par 346 [Torque Positive]
Par 347 [Torque Negative]
Par 20
[Ramp Delay]
22 [MOP Accel Time] Default: 10 2

The acceleration rate for the MOP reference in response to a digital Min/Max: 0 / 65535
input. The MOP acceleration rate = Par 2 [Maximum Speed] / Par 22 Units: s
[MOP Accel Time].
If “0” is entered in this parameter, the ramp output directly follows the
reference value.
24 [Accel Time 2] Default: 10 2
Sets the rate of acceleration for Ramp 2. Min/Max: 0 / 65535
Acceleration rate for Ramp 2 = Par 2 [Maximum Speed] / Par 24 Units: s
[Accel Time 2].
30 [MOP Decel Time] Default: 10 2
The deceleration rate for the MOP reference in response to a digital Min/Max: 0 / 65535
input. The MOP deceleration rate = Par 2 [Maximum Speed] / Par 30 Units: s
[MOP Decel Time].
1410 [Jog Ramp Time] Default: 10 2
Sets the rate of acceleration and deceleration while the Jog function Min/Max: 0 / 65535
is active. The Jog rate = Par 2 [Maximum Speed] / Par 1410 [Jog Units: s
Ramp Time].
Note: This parameter was added with firmware version 2.001.

Related
Group
File
No.
32 [Decel Time 2] Default: 10 2
Sets the rate of deceleration for Ramp 2. Min/Max: 0 / 65535
Deceleration rate for Ramp 2 = Par 2 [Maximum Speed] / Par 30 Units: s
[Decel Time 2].
245 [Speed Ramp En] Default: 1= “Enabled”
Enables or disables the ramp function. The Ramp Reference block is Options: 0= “Disabled”
bypassed when this parameter is set to 0 “Disabled”. 1= “Enabled”
344 [Zero Ramp Output] Default: 1= “Not Active”
Activates either the ramp output (1) or the brake function (0). When Options: 0= “Active”
A this parameter is set to 0 “Active”, the drive brakes through the 1= “Not Active”
maximum available torque and the motor will perform a Current Limit
Stop. Two quadrant drives do not support a brake option.
• “Active” = The ramp output is disabled and Pars 113 [Ramp Out]
and 114 [Ramp Out Pct] are immediately set to zero.
• “Not Active” = The ramp output is enabled. and Pars 113 [Ramp
Out] and 114 [Ramp Out Pct] follow the Ramp Reference block
commands.
345 [Zero Ramp Input] Default: 1= “Not Active” 110,
Activates or deactivates the ramp input. Options: 0= “Active” 111
A • “Active” = The ramp input is not active and Pars 110 [Ramp In] and 1= “Not Active”
111 [Ramp In Pct] = 0.
• “Not Active” = The ramp input is activated and Pars 110 [Ramp In]
and 111 [Ramp In Pct] correspond to the set reference.
373 [Freeze Ramp] Default: 1= “Not Active”
DYNAMIC CONTROL
Determines whether the last ramp output reference value is retained Options: 0= “Active”
A or whether the ramp output reference value is active. 1= “Not Active”
Ramp Rates
• “Active” = The value of the ramp output at the time of activation is

retained irrespective of any possible reference value changes at
the ramp input.
• “Not Active” = The ramp output value follows the ramp input value
according to the Ramp Reference Block commands.
660 [Accel Time 1] Default: 10 2
Sets the rate of acceleration for Ramp 1. Min/Max: 0 / 65535
Acceleration rate for Ramp 1 = Par 2 [Maximum Speed] / Par 660 Units: s
[Accel Time 1].
662 [Decel Time 1] Default: 10 2
Sets the rate of deceleration for Ramp 1. Min/Max: 0 / 65535
Deceleration rate for Ramp 1 = Par 2 [Maximum Speed] / Par 662 Units: s
[Decel Time 1].
665 [S Curve Accel 1] Default: 1.00
Defines the acceleration curve for S–shaped ramp 1. Min/Max: 0.10 / 60.00
A Units: s
666 [S Curve Decel 1] Default: 1.00
Defines the deceleration curve for S–shaped ramp 1. Min/Max: 0.10 / 60.00
A Units: s
667 [S Curve Accel 2] Default: 1.00
Defines the acceleration curve for S–shaped ramp 2. Min/Max: 0.10 / 60.00
A Units: s
668 [S Curve Decel 2] Default: 1.00
Defines the deceleration curve for S–shaped ramp 2. Min/Max: 0.10 / 60.00
A Units: s
1212 [Acc Dec Filter] Default: 30
Internal acceleration/deceleration calculation filter for the Torque Min/Max: 0 / 5000
Winder line speed reference. Units: ms

Related
Group
File
No.
13 [Torq Red CurLim] Default: 100 342
A The armature current limit, defined as a percentage of the value Min/Max: 0 / 200
defined in Par 179 [Nom Mtr Arm Amps] when Par 342 [Torque Units: %
Reduction] is set to 1 “Active”.
696 [Droop Percent] Default: 0.00 41,
Droop function gain is a percentage of the ratio between Par 45 [Max Min/Max: 0.00 / 100.00 45,
A Ref Speed] and the difference of Par 698 [Load Comp] – Par 41 Units: % 698
[Current Reg In]. Therefore, when the difference between Par 698
[Load Comp] and Par 41 [Current Reg In] = 100% and Par 696 [Droop
Percent] = 100%, the speed reference correction signal is equal to Par
45 [Max Ref Speed].
697 [Droop Filter] Default: 0
Droop filter time constant for the Droop function. Min/Max: 0 / 1000
A Units: ms
698 [Load Comp] Default: 0
The load compensation signal. This value is typically equal to the Min/Max: + / –200
A “master” drive’s current. The load compensation signal is a Units: %
percentage of Idn.
699 [Enable Droop] Default: 0= “Disabled”
Enables/Disables the Droop function. Options: 0= “Disabled”
A
Load Limits
• “Enabled” = The Droop function is enabled. 1= “Enabled”

• “Disabled” = The Droop function is disabled.
DYNAMIC CONTROL
700 [Droop Limit] Default: 1750

The speed reference correction range within which the droop function Min/Max: 0 / Par 45 [Max Ref Speed]
A becomes active. Units: RPM
715 [Torq Limit Type] Default: 0= “Torq Lim Pos” 7,
This parameter determines the response of the drive during a current Options: 0= “Torq Lim Pos” 8,
limiting condition. 1= “Torq Lim Mtr” 9,
• “Torq Lim Pos” = The active positive torque limit is set by the value 162
A
defined in Par 7 [Current Limit] and the active negative torque limit
defined in Par 9 [Current Lim Neg].
• “Torq Lim Mtr” = With this selection three conditions are possible:
1.If the motor speed > +1% of Par 162 [Max Feedback Spd], the
active positive torque limit is defined by Par 8 [Current Lim Pos]
and the active negative torque limit is defined by Par 9 [Current
Lim Neg].
2.If the motor speed < –1% of Par 162 [Max Feedback Spd] the
active positive torque limit is defied by Par 9 [Current Lim Neg]
and the active negative torque limit is defined by Par 8 [Current
Lim Pos].
3.If –1% of Par 162 [Max Feedback Spd] < motor speed < +1% of
Par 162 [Max Feedback Spd] the active positive torque limit is
define by Par 8 [Current Lim Pos] and the active negative torque
limit is defined by Par 9 [Current Lim Neg].
38 [Fast Stop Time] Default: 10 354,
The amount of time to decelerate the drive to a complete stop and Min/Max: 0 / 65535 365
A disable the drive. The deceleration rate for Fast stop = [Maximum Units: s
Stop Modes
Speed] / [Fast Stop Time]. This feature can be used when [Digital Inx
Sel] is set to 30 “Fast Stop” or when certain faults are configured for
“Quick Stop”.
627 [Spd 0 Trip Delay] Default: 0
The amount of time that will elapse after the drive reaches zero speed Min/Max: 0 / 40000
A before it is disabled. Units: ms

Related
Group
File
No.
1262 [Closing Speed] Default: 30
A Motor speed at which the brake is closed. Used with External Brake
Control.
Min/Max:
Units:
0 / 200
RPM
1263 [Opening Delay] Default: 0
Stop Modes
A Amount of time before the brake will open after the drive has been
enabled. Used with External Brake Control.
Min/Max:
Units:
0 / 30000
ms
1265 [Ramp In Zero En] Default: 0= “Disabled”
A Enables/Disables the setting of the ramp input to zero. Used with
External Brake Control.
Options: 0=
1=
“Disabled”
“Enabled”
1266 [Actuator Delay] Default: 0
A Amount of time before the actuator releases the load. Used with
External Brake Control.
Min/Max:
Units:
0 / 30000
ms
1344 [Start At Powerup] Default: 0= “Disabled” 1345
Enables/Disables the ability to issue a “Run” command and Options: 0= “Disabled”
automatically resume running at commanded speed after drive input 1= “Enabled”
power is restored and the time in Par 1345 [Powerup Delay] has
elapsed. Requires a digital input configured for “Run” and a valid start
condition.
Restart Modes
ATTENTION: Equipment damage and/or personal injury may result if this parameter is used in
an inappropriate application. Do not use this function without considering applicable local,
! national and international codes, standards, regulations or industry guidelines.
1345 [Powerup Delay] Default: 1 1344

DYNAMIC CONTROL
Defines the programmed delay time, in seconds, before a start Min/Max: 1 / 10800
command is accepted after a power up. If a “Start”, “Run” or “Stop” Units: s
command is asserted before the time in this parameter expires, the
“Start At Powerup” function will be aborted.
181 [Adaptive Spd En] Default: 0= “Disabled” 182,
Enables/Disables adaptive speed regulation. Options: 0= “Disabled” 183
The adaptive speed regulator function enables different gains of the 1= “Enabled”
A speed regulator depending on the speed or another variable (Par 183
[Adaptive Ref]). This allows optimum adaptation of the speed
regulator to your specific application. When adaptive speed regulation
is disabled, the regulator operates based on the settings in the
individual regulation parameters.
182 [Adaptive Reg Typ] Default: 0= “Speed” 183
Selects the type of regulation used. Options: 0= “Speed”
• “Speed” = The regulator parameters follow a speed reference. 1= “Adaptive Ref”
A • “Adaptive Ref” = The regulator parameters follow the reference
Adaptv Regulator
produced by Par 183 [Adaptive Ref].

183 [Adaptive Ref] Default: 1000 182
A The variable reference that the speed regulator parameter will follow
when Par 182 [Adaptive Reg Typ] = 1 “Adaptive Ref”.
Min/Max:
Units:
–32768/+32767
RPM
184 [Adaptive Spd 1] Default: 20.34 183,
186
A A183percentage of Par 45 [Max Ref Speed] or the maximum value of Par
[Adaptive Ref].
Min/Max:
Units:
0.00 / 200.00
%
Parameter set 1 is valid below the value set in this parameter and
parameter set 2 is valid above the value set in this parameter. The
transition between the values is defined by Par 186 [Adaptive Joint 1].
185 [Adaptive Spd 2] Default: 40.69 183,
187
A A183percentage of Par 45 [Max Ref Speed] or the maximum value of Par
[Adaptive Ref].
Min/Max:
Units:
0.00 / 200.00
%
Parameter set 2 is valid below the value set in this parameter and
parameter set 3 is valid above the value set in this parameter. The
transition between the values is defined by Par 187 [Adaptive Joint 2].

Related
Group
File
No.
186 [Adaptive Joint 1] Default: 6.11 184
Defines a range above and below the value set in Par 184 [Adaptive Min/Max: 0.00 / 200.00
A Spd 1] within which there is a linear change in gain from parameter Units: %
set 1 to parameter set 2 in order to prevent jumps in the adaptive
speed regulator. The value in this parameter is defined as percentage
of the value defined Par 45 [Max Ref Speed].
187 [Adaptive Joint 2] Default: 6.11 185
Defines a range above and below the value set in Par 185 [Adaptive Min/Max: 0.00 / 200.00
A Spd 2] with in which there is a linear change in gain from parameter Units: %
set 2 to parameter set 3 in order to prevent jumps in the adaptive
speed regulator. The value in this parameter is defined as percentage
of the value defined Par 45 [Max Ref Speed].
188 [Adaptive P Gain1] Default: 10.00 93,
Proportional gain for the range from zero to the value set in Par 184 Min/Max: 0.00 / 100.00 184
A [Adaptive Spd 1]. The value in this parameter is defined as Units: %
percentage of the value defined in Par 93 [Spd Reg Kp Base].
189 [Adaptive I Gain1] Default: 1.00 94,
DYNAMIC CONTROL
Adaptv Regulator
Integral gain for the range from zero to Par 184 [Adaptive Spd 1]. The Min/Max: 0.00 / 100.00 184
A value in this parameter is defined as percentage of the value defined Units: %
Par 94 [Spd Reg Ki Base].
Proportional gain for the range of values defined beginning with the Min/Max: 0.00 / 100.00 184,
A value of Par 184 [Adaptive Spd 1] to the value defined in Par 185 Units: % 185
[Adaptive Spd 2]. The value in this parameter is defined as
percentage of the value defined Par 93 [Spd Reg Kp Base].
Integral gain for the range of values defined beginning with the value Min/Max: 0.00 / 100.00 184,
A of Par 184 [Adaptive Spd 1] to the value defined in Par 185 [Adaptive Units: % 185
Spd 2]. The value in this parameter is defined as percentage of the
value defined Par 94 [Spd Reg Ki Base].
Proportional gain for the range of values beginning above the value Min/Max: 0.00 / 100.00 185
A defined in Par 185 [Adaptive Spd 2]. The value in this parameter is Units: %
defined as percentage of the value defined Par 93 [Spd Reg Kp
Base].
Integral gain for the range of values beginning above the value Min/Max: 0.00 / 100.00 185
A defined in Par 185 [Adaptive Spd 2]. The value in this parameter is Units: %
defined as percentage of the value defined Par 94 [Spd Reg Ki Base].

Applications File
Related
Group

File
No.

695 [PI Steady Thrsh] Default: 0 758
Feed–forward threshold for PI. Min/Max: 0 / 10000
A • If the value if Par 758 [Feed Fwd PID] is less than the value of Par
695 [PI Steady Thrsh] the integral regulation will be locked and the
proportional gain assumes the value set in Par 793 [PI Init Prop
Gn].
• When the value of Par 758 [Feed Fwd PID] exceeds the value of
Par 695 [PI Steady Thrsh], the integral regulation with the gain set
in Par 734 [PI Init Intgl Gn] will be enabled.
• The Proportional / Integral (PI) block will maintain the gain values
specified in Pars 793 [PI Init Prop Gn] and 734 [PI Init Intgl Gn] for
the time specified in Par 731 [PID Steady Delay]; once this time
delay has elapsed, the values of [PI Init Prop Gn] and [PI Init Intgl
Gn] will be brought automatically to the values specified in Pars
765 [PI Prop Gain PID] and 764 [PI Integral Gain], respectively.
764 [PI Integral Gain] Default: 10.00
Integral gain of the PI block. Min/Max: 0.00 / 100.00
A
765 [PI Prop Gain PID] Default: 10.00
Proportional gain of the PI block. Min/Max: 0.00 / 100.00
A
769 [Enable PI] Default: 0= “Disabled”
APPLICATIONS
Enables/Disables the PI portion of the PID regulator. If assigned to a Options: 0= “Disabled”

A
PI Control
digital input, this parameter must be brought at a high logical level 1= “Enabled”
(+24V).
771 [PI Output] Default: Read Only 784,
Output value of the PI block, adapted to the value between the values Min/Max: 0 / 10000 785,
A defined in Pars 784 [PI Upper Limit] and 785 [PI Lower Limit]. When 779
the drive is turned on, the value of this parameter is acquired
automatically based on the value of Par 779 [PI Central v sel] x 1000.
776 [PI Central v1] Default: 0.00 784,
The first value that can be selected, via Par 779 [PI Central v sel], as Min/Max: Par 785 [PI Lower Limit] / Par 784 785,
A the initial output of the PID regulator’s integral component [PI Upper Limit] 779
(corresponding to initial diameter 1). The value entered in this
parameter must be less than the value set in Par 784 [PI Upper Limit]
and greater than the value set in Par 785 [PI Lower Limit].
The second value that can be selected, via Par 779 [PI Central v sel], Min/Max: Par 785 [PI Lower Limit] / Par 784 785,
A as the initial output of the PID regulator’s integral component (corre- [PI Upper Limit] 779
sponding to initial diameter 2). The value entered in this parameter
must be less than the value set in Par 784 [PI Upper Limit] and great-
er than the value set in Par 785 [PI Lower Limit].
The third value that can be selected, via Par 779 [PI Central v sel], as Min/Max: Par 785 [PI Lower Limit] / Par 784 785,
A the initial output of the PID regulator’s integral component [PI Upper Limit] 779
(corresponding to initial diameter 3). The value entered in this
parameter must be less than the value set in Par 784 [PI Upper Limit]
and greater than the value set in Par 785 [PI Lower Limit].

Related
Group
File
No.
779 [PI Central v sel] Default: 1 769,
Selects one of the four possible initial output values of the PID Min/Max: 0/3 776,
A regulator integral component (corresponding to the initial diameter) of 777,
the PI block. 778,
• “0” = When the PI block is disabled (Par 769 [Enable PI] = 780,
“Disabled”), the last value of the integral component calculated 781
(corresponding to swift diameter) is stored in Par 771 [PI Output].
This value is used by the PID regulator when the PI block is
enabled again and the drive is restarted. This function is useful
when for any reason the drive must be turned off or if incoming
power is removed from the drive.
• “1”, “2”, or “3” = When the PI block is disabled (Par 769 [Enable PI]
= “Disabled”), the value of [PI Output] will be set to the value of the
selected parameter (“1” = 776 [PI Central v1], “2” = 777, [PI Central
v2], or “3” = 778 [PI Central v3] x1000). This value is only used by
the PID regulator when the drive is powered up and Par 769
[Enable PI] is already enabled.
Note: Par 779 [PI Central v sel] can be set directly from the HIM or
through two digital inputs set respectively as “PI central vs0” and “PI
central vs1”. Refer to Pars 780 [PI Central vs0] and 781 [PI Central
vs1] for more information on this configuration.
780 [PI Central vs0] Default: 0
When assigned to a digital input and used in combination with Par Min/Max: 0/1
A 781 [PI Central vs1], through binary selection, determines which of
the four possible output values is used as the initial level of the
integral component (corresponding to the initial diameter) of the PI
block.
APPLICATIONS
Par 780 Par 781 Selects the value in . . .

PI Control
0 0 Par 771 [PI Output]

0 1 Par 776 [PI Central v1]
781 [PI Central vs1] Default: 0

The output selector of the initial PI block. With the value of Par 780 [PI Min/Max: 0/1
A Central vs0] determined, through binary selection, what between the
four possible settings of the integral initial level (correspondent to
initial diameter) can be used. See Par 780 [PI Central vs0] for binary
selections.
783 [PI integr freeze] Default: 0= “Off”
Locks the selections made for the integral component of the PID Options: 0= “Off”
A regulator. 1= “On”
784 [PI Upper Limit] Default: 10.00
Defines the upper limit of the adapting block for correction of the PI Min/Max: Par 785 [PI Lower Limit] / 10.00
A block.
785 [PI Lower Limit] Default: 0.00
Defines the lower limit of the adapting block for correction of the PI Min/Max: –10.00 / Par 784 [PI Upper Limit]
A block.
793 [PI Init Prop Gn] Default: 10.00 695,
The initial value of the proportional gain. This parameter is active Min/Max: 0.00 / 100.00 731,
A when, 769
• its value has exceeded the value of Par 695 [PI Steady Thrsh],
• the amount of time defined in Par 731 [PID Steady Delay] has
elapsed, and feed–forward is less than the value defined in Par 695
[PI Steady Thrsh], or
• Par 769 [Enable PI] transitions from “0” (low) to “1” (high) and the
amount of time defined in Par 731 [PID Steady Delay] has elapsed.

Related
Group
File
No.
421 [PD Output PID] Default: Read Only
Proportional / Derivative (PD) block output. Min/Max: –/+10000
A
766 [PD Deriv Gain 1] Default: 1.00 181
First derivative gain of the PD block. The value specified in this field Min/Max: 0.00 / 100.00
A depends on the enabling and configuration of Par 181 [Adaptive Spd
En].
767 [PD Deriv Filter] Default: 0
Time constant of the filter from the derivative portion of the PD block. Min/Max: 1 / 1000
A Units: ms
768 [PD Prop Gain 1] Default: 10.00 181
First proportional gain of the block PD. The value specified in this field Min/Max: 0.00 / 100.00
En].
770 [Enable PD] Default: 0= “Disabled”
PD Control
Enables/disables the PD portion of the PID regulator. Options: 0= “Disabled”

A Note: This parameter can be assigned to a digital input. 1= “Enabled”
Second proportional gain of the block PD. The value specified in this Min/Max: 0.0 / 100.0
A field depends on the enabling and configuration of Par 181 [Adaptive
Spd En].
Second derivative gain of the PD block. The value specified in this Min/Max: 0.0 / 100.0
Spd En].
APPLICATIONS

Third proportional gain of the block PD. The value specified in this Min/Max: 0.0 / 100.0
Spd En].
Third derivative gain of the PD block. The value specified in this field Min/Max: 0.00 / 100.00
En].
418 [Real FF PID] Default: Read Only 758,
Represents the feed–forward value which has been recalculated Min/Max: –/+10000 771
according to the PI correction. It will be calculated with the following
formula:
Par 418 [Real FF PID] = (Par 758 [Feed Fwd PID] / 1000 ) x Par 771
[PI Output]
When either the negative or positive limit of this parameter has been
reached, further increases in the value of Par 771 [PI Output] will be
blocked in order to avoid undesirable saturation of the PID regulator.
For example:
PID Control
When Par 758 [Feed Fwd PID] = +8000, the positive limit of Par 771
[PI Output] will be automatically set at 10000 / ( 8000 / 1000 ) = 1250.
731 [PID Steady Delay] Default: 0 695,
The amount of time for which the gains in Pars 793 [PI Init Prop Gn] Min/Max: 0 / 60000 734,
A and 734 [PI Init Intgl Gn] will remain enabled after feed–forward has Units: ms 793
exceeded the threshold value defined in Par 695 [PI Steady Thrsh].
734 [PI Init Intgl Gn] Default: 10.00 695,
The initial value of the integral gain. This parameter is active when Min/Max: 0.00 / 100.00 731,
A feed–forward is greater than the value defined in Par 695 [PI Steady 769
Thrsh], or Par 769 [Enable PI] transitions from “0” (low) to “1” (high)
and the amount of time defined in Par 731 [PID Steady Delay] has
elapsed.

Related
Group
File
No.
757 [PID Clamp] Default: 10000 759,
The PID “clamp” allows a smooth tension setting of a controlled Min/Max: 0 / 10000 763,
A system winder/unwinder when the calculation of the initial diameter 770
function cannot be used.
• When enabling the drive, the dancer is at the lowest point of its full
scale. In this case, with Par 759 [PID Error] at its maximum value,
the motor could accelerate too fast to properly configure the dancer
for its central operating position. By setting the value of Par 757
[PID Clamp] sufficiently low. e.g, = 1000, when the drive starts and
Par 770 [Enable PD] = 1 “Enable”, the value of Par 759 [PID Error]
is limited to 1000 until the signal coming from the dancer (via Par
763 [PID Feedback]) goes above the value in this field. Then, the
value of [PID Clamp] is automatically returned to its maximum
value of 10000. The PID clamp is kept at 10000 until the drive
stops or Par 770 [Enable PD] = 0 “Disabled”.
758 [Feed Fwd PID] Default: Read Only
Feedback from the transducer position (dancer) or tension. Min/Max: –/+10000
A
759 [PID Error] Default: Read Only
Error value input to the PID function (output of the PID Clamp block). Min/Max: –/+10000
A
APPLICATIONS
760 [PID Setpoint 0] Default: 0 763

PID Control
First offset value added to Par 763 [PID Feedback]. This parameter Min/Max: –/+10000
A can be assigned to an analog input, e.g., for the tension setting when
a load cell must be used as feedback.
761 [PID Setpoint 1] Default: 0 763
Second offset value added to Par 763 [PID Feedback]. Min/Max: –/+10000
A
762 [PID Setpoint Sel] Default: 0= “Setpoint 0” 763
Selects the offset value added to Par 763 [PID Feedback]. This Options: 0= “Setpoint 0”
A parameter can be assigned to a digital input. 1= “Setpoint 1”
763 [PID Feedback] Default: 0
Analog input feedback value received from the transducer position Min/Max: –/+10000
A (dancer) or tension (load cell).
772 [PID Output Sign] Default: 1= “Bipolar”
Determines whether the output of the PID regulator is bipolar or Options: 0= “Positive”
A positive (clamp of the negative side). 1= “Bipolar”
773 [PID Output Scale] Default: 1.00 774
Scale factor for Par 774 [PID Output]. The value of this parameter Min/Max: –/+100.00
A depends on to which parameter you want to send the PID regulator
output.
774 [PID Output] Default: Read Only
Displays the PID regulator output. Min/Max: –/+10000
A Note: This parameter can be assigned to an analog output in order to
provide a cascaded reference in multi-drive systems.

Related
Group
File
No.
782 [PID Target] Default: 0= “Not Used”
Parameter number to which the PID Output value will be written.
A
Options:
0= “Not Used” 16 = “Reserved” 32 = “UsrDefined13” (Par 516)

1= “Cur Lim Pos” (Par 8) 17 = “Max Fld Pct” (Par 467) 33 = “UsrDefined14” (Par 517)
2= “Cur Lim Neg” (Par 9) 18 = “Reserved” 34 = “UsrDefined15” (Par 518)
3= “Reserved” 19 = “UsrDefined0” (Par 503) 35 = “Load Comp” (Par 698)
4= “Reserved” 20 = “UsrDefined1” (Par 504) 36 = “Out Volt Lvl” (Par 921)
5= “TrqRedCurLim” (Par 13) 21 = “UsrDefined2” (Par 505) 37 = “Reserved”
6= “Torque Ref” (Par 39) 22 = “UsrDefined3” (Par 506) 38 = “Speed Ratio” (Par 1017)
7= “Trim Torque” (Par 40) 23 = “UsrDefined4” (Par 507) 39 = “Reserved”
8= “Reserved” 24 = “UsrDefined5” (Par 508) 40 = “Reserved”
9= “Trim Ramp” (Par 42) 25 = “UsrDefined6” (Par 509) 41 = “Tension Red” (Par 1179)
10 = “Trim Speed” (Par 43) 26 = “UsrDefined7” (Par 510) 42 = “Reserved”
11 = “Reserved” 27 = “UsrDefined8” (Par 511) 43 = “Reserved”
12 = “Reserved” 28 = “UsrDefined9” (Par 512) 44 = “CloseLp Comp” (Par 1208)
13 = “Reserved” 29 = “UsrDefined10” (Par 513) 45 = “Reserved”
14 = “Adaptive Ref” (Par 183) 30 = “UsrDefined11” (Par 514) 46 = “Reserved”
15 = “Reserved” 31 = “UsrDefined12” (Par 515)
786 [PID Source] Default: 0 “Not Used”

Parameter number from which the PID source value will be read.
A
APPLICATIONS
Options:
PID Control
0= “Not Used” 16 = “SpdRegOutPct” (Par 236) 32 = “UsrDefined13” (Par 516)

1= “Cur Lim Pos” (Par 8) 17 = “Max Fld Pct” (Par 467) 33 = “UsrDefined14” (Par 517)
2= “Cur Lim Neg” (Par 9) 18 = “Fld Ref Pct” (Par 500) 34 = “UsrDefined15” (Par 518)
3= “CurLimPosOut” (Par 10) 19 = “UsrDefined0” (Par 503) 35 = “Load Comp” (Par 698)
4= “CurLimNegOut” (Par 11) 20 = “UsrDefined1” (Par 504) 36 = “Out Volt Lvl” (Par 921)
5= “TrqRedCurLim” (Par 13) 21 = “UsrDefined2” (Par 505) 37 = “Filt Trq Cur” (Par 928)
6= “Torque Ref” (Par 39) 22 = “UsrDefined3” (Par 506) 38 = “Speed Ratio” (Par 1017)
7= “Trim Torque” (Par 40) 23 = “UsrDefined4” (Par 507) 39 = “Spd Draw Out” (Par 1018)
8= “TorqueReg In” (Par 41) 24 = “UsrDefined5” (Par 508) 40 = “Roll Diam” (Par 1154)
9= “Trim Ramp” (Par 42) 25 = “UsrDefined6” (Par 509) 41 = “Tension Red” (Par 1179)
10 = “Trim Speed” (Par 43) 26 = “UsrDefined7” (Par 510) 42 = “Torq Cur Pct” (Par 1193)
11 = “Ramp In” (Par 110) 27 = “UsrDefined8” (Par 511) 43 = “Ten Ref Pct” (Par 1194)
12 = “Ramp Out” (Par 113) 28 = “UsrDefined9” (Par 512) 44 = “CloseLp Comp” (Par 1208)
13 = “Speed Reg In” (Par 118) 29 = “UsrDefined10” (Par 513) 45 = “Actual Comp” (Par 1213)
14 = “Adaptive Ref” (Par 183) 30 = “UsrDefined11” (Par 514) 46 = “W Reference” (Par 1217)
15 = “Arm Cur Pct” (Par 199) 31 = “UsrDefined12” (Par 515)
787 [PID Source Gain] Default: 1.00 786

Gain of the input value to Par 786 [PID Source]. Min/Max: –/+100.00
A
1046 [PID Accel Time] Default: 0.00
Ramp acceleration time after the block PID offset. Min/Max: 0.00 / 900.00
A Units: s
1047 [PID Decel Time] Default: 0.00
Ramp deceleration time after the block PID offset. Min/Max: 0.00 / 900.00
A Units: s

Related
Group
File
No.
1254 [PID Error Gain] Default: 1.005 759
PID Control
Gain percentage of Par 759 [PID Error]. Min/Max: 0.000 / 32.010

A Units: %
1258 [Enable PID] Default: 0= “Disabled”
Enables/Disables both the PI and PD portions of the PID regulator. Options: 0= “Disabled”
A 1= “Enabled”
484 [Scale1 Input] Default: 0
553 [Scale2 Input]
1218 [Scale3 Input] Min/Max: 0 / 1408
1227 [Scale4 Input]
1236 [Scale5 Input]
1245 [Scale6 Input]
Parameter number from which the value is read and used as the input
A quantity to the Scale block. Refer to the Scale Blocks block diagram
on page D-18 for more information.
485 [Scale1 Output] Default: 0
554 [Scale2 Output]
1219 [Scale3 Output] Min/Max: 0 / 1408
1228 [Scale4 Output]
Parameter number to which the value of the Scale block output is
A written. Refer to the Scale Blocks block diagram on page D-18 for
more information.
486 [Scale1 Mul] Default: 1.00
555 [Scale2 Mul]
Min/Max: –/+10000.00
APPLICATIONS
1220 [Scale3 Mul]

1229 [Scale4 Mul]
1238 [Scale5 Mul]
1247 [Scale6 Mul]
Scale Blocks
Multiplier of the input quantity (after a possible limitation). Resolution:

A 5 digits. Refer to the Scale Blocks block diagram on page D-18 for
more information.
487 [Scale1 Div] Default: 1.00
556 [Scale2 Div]
1221 [Scale3 Div] Min/Max: –/+10000.00
1230 [Scale4 Div]
1239 [Scale5 Div]
1248 [Scale6 Div]
Divisor, through which it is possible to divide the input quantity already
A multiplied and limited. Resolution: 5 digits. Refer to the Scale Blocks
block diagram on page D-18 for more information.
488 [Scale1 In Max] Default: 0.00
557 [Scale2 In Max]
1222 [Scale3 In Max] Min/Max: – 231/ +231 – 1
1231 [Scale4 In Max]
Maximum limit of the input quantity. Resolution: 5 digits. Refer to the
A Scale Blocks block diagram on page D-18 for more information.
489 [Scale1 In Min] Default: 0.00
558 [Scale2 In Min]
1223 [Scale3 In Min] Min/Max: – 231/ +231 – 1
1232 [Scale4 In Min]
Minimum limit of the input quantity. Resolution: 5 digits. Refer to the
A Scale Blocks block diagram on page D-18 for more information.

Related
Group
File
No.
490 [Scale1 In Off] Default: 0.00
559 [Scale2 In Off]
1224 [Scale3 In Off] Min/Max: – 231/ +231 – 1
1233 [Scale4 In Off]
Offset to be added to the input quantity. Resolution: 5 digits. Refer to
A the Scale Blocks block diagram on page D-18 for more information.
491 [Scale1 Out Off] Default: 0.00
560 [Scale2 Out Off]
1225 [Scale3 Out Off] Min/Max: – 231/ +231 – 1
Scale Blocks

Offset to be added to the output quantity. Resolution: 5 digits. Refer to
A the Scale Blocks block diagram on page D-18 for more information.
492 [Scale1 In Abs] Default: 0= “Off”
561 [Scale2 In Abs]
1226 [Scale3 In Abs] Options: 0= “Off”
1235 [Scale4 In Abs] 1= “On”
1244 [Scale5 In Abs]
1253 [Scale6 In Abs]
Controls how the input value is processed.
A • “Off” = The input quantity is processed with its sign.
• “On” = The input quantity is processed with a positive sign
(absolute value).
It is possible to have the polarity change with the signs of the
[ScalexMul] or [ScalexDiv] parameters. Refer to the Scale Blocks
block diagram on page D-18 for more information.
APPLICATIONS
794 [Diameter Calc] Default: 0

Enables/Disables the diameter calculation function. If this parameter Min/Max: 0/1
has been programmed via a digital input, it must be brought to a
A logical high level.
• “0” = The diameter calculation is disabled.
• “1” = The diameter calculation is enabled.
795 [DncrPosSpd] Default: 0
Desired motor speed when the dancer is positioned in its central Min/Max: –/+100
A working position.
796 [Max Deviation] Default: 8000
A value, expressed in counts of D/A, that corresponds to the position Min/Max: –/+10000
A of maximum shift admitted by the dancer. This value is considered the
starting measurement of the dancer movement during the initial
Diameter Calc
diameter calculation phase.

797 [Gear Box Ratio] Default: 1.000
Ratio reduction between the motor and the swift (< = 1). Min/Max: 0.000 / 1.000
A
798 [Dancer Constant] Default: 1
The measurement corresponding to the total bunching of the material Min/Max: 1 / 10000
A in the dancer. Units: mm
799 [Minimum Diameter] Default: 100
Minimum value of the swift diameter. Min/Max: 1 / 2000
Units: mm
A
800 [Diameter Calc St] Default: Read Only
Status of the initial diameter calculation. Min/Max: 0/1
A • “0” = The initial diameter calculation has not completed.
• “1” = The initial diameter calculation has completed.
Note: This parameter can be assigned to a digital output.

Related
Group
File
No.
1153 [Max Diameter] Default: 1.00
Maximum roll diameter. Min/Max: 0.00 / 32.00
Units: m
A
1154 [Roll Diameter] Default: Read Only
A Displays the calculated roll diameter. Note: This parameter can be
assigned to an analog output as a percentage of Par 1153 [Max
Min/Max:
Units:
0.00 / 32.00
m
Diameter].
1155 [Line Spd Thresh] Default: 5.00 1162,
1206,
A Line speed detecting threshold. When the value of Par 1286 [Ref Line
Speed] is lower than the value of [Line Spd Thresh], the diameter
Min/Max:
Units:
0.00 / 150.00
% 1207,
calculation stops and the diameter is kept at a constant value. When 1286
the value of [Ref Line Speed] overcomes the threshold, the diameter
calculation is enabled with an initial filter corresponding to the value in
Par 1206 [Diam init filter] for the time set in Par 1207 [Diam stdy
delay]. At the end of this time the filter will be set to the value of Par
1162 [Diameter Filter].
1156 [Line Spd Gain] Default: 0 1160,
1284
A Calibration value used to obtain Par 1160 [Line Speed Pct] = 100% at
its maximum value. The value of this parameter depends on the value
Min/Max: 0 / 32767
of Par 1284 [Ref Spd Source]:

[Line Spd Gain] = [32768 x 16384 / (maximum value of [Ref Spd
Source] x 8)] -1
1157 [Diameter Reset] Default: 0 1168
A Diameter reset. When this parameter is set to “1”, the diameter
starting value is set to the value in Par 1168 [Diam Preset Sel].
Min/Max: 0/1
APPLICATIONS
1158 [Diam Threshold] Default: 10.00 1153,

Diameter Calc
1159
A Diameter threshold as a percentage of Par 1153 [Max Diameter]. Par
1159 [Diameter Reached] is set to “1” when the value in this
Min/Max:
Units:
0.00 / 150.00
%
parameter is exceeded.
1159 [Diameter Reached] Default: Read Only 1158
A Indication that the diameter threshold set in Par 1158 [Diam
Threshold] has been exceeded.
Min/Max: 0/1
• “0” = The diameter threshold has not been exceeded.

• “1” = The diameter threshold has been exceeded.
1160 [Line Speed Pct] Default: Read Only
Line speed. Min/Max: 0.00 / 150.00
A Units: %
1161 [Diam Calc Dis] Default: 1= “On” 1155
A Enables/Disables the diameter calculation (see also Par 1155 [Line
Spd Thresh]). The last calculated diameter value is saved if this
Options: 0=
1=
“Off”
“On”
parameter is changed to 0 “Off” while the diameter is being
calculated.
1162 [Diameter Filter] Default: 100
Diameter calculation filter. Min/Max: 0 / 5000
A Units: ms
1163 [Base Omega] Default: 1500
A Winder speed at the maximum line speed and minimum diameter of
the winder/unwinder (motor shaft side).
Min/Max:
Units:
0 / 8191
RPM
1164 [Diam Preset 0] Default: 1.00 799,
1153
A First preset starting diameter. The value of this parameter must be set
between the value of Pars 799 [Minimum Diameter] and 1153 [Max
Min/Max:
Units:
0.00 / 32.00
m
Diameter].
1153
A Second preset starting diameter. The value of this parameter must be
set between the value of Pars 799 [Minimum Diameter] and 1153
Min/Max:
Units:
0.00 / 32.00
m
[Max Diameter].

Related
Group
File
No.
1153
A Third preset starting diameter. The value of this parameter must be
Min/Max:
Units:
0.00 / 32.00
m
[Max Diameter].
1153
A Fourth preset starting diameter. The value of this parameter must be
Min/Max:
Units:
0.00 / 32.00
m
[Max Diameter]. This parameter can be assigned to an analog input. If
an analog input is used, +10V corresponds to the value of [Max
Diameter] and the voltage corresponding to the minimum diameter =
10 x ([Minimum Diameter] / [Max Diameter]).
1168 [Diam Preset Sel] Default: 0 1164,
1165,
A Selects the starting diameter for the Diameter Calculation function.
• 0 = Par 1164 [Diam Preset 0]
Min/Max: 0/3
1166,
• 1 = Par 1165 [Diam Preset 1] 1167
This parameter can also be set via two digital inputs programmed as
Diameter Calc
57 “Diam Preset0” and 58 “Diam Preset1”; the selection in this case is

carried out with binary logic.
“Diam Preset1” “Diam Preset0” Selection

0 0 Par 1164 [Diam Preset 0]
APPLICATIONS
1205 [Diam Inc Dec En] Default: 1= “Enabled”

A This parameter It is used to improve system stability for winder/
unwinder applications. If this parameter is enabled and if applied to a
Options: 0=
1=
“Disabled”
“Enabled”
winder, the calculated diameter can never decrease; if applied to an
unwinder, the calculated diameter can never increase.
1206 [Diam init filter] Default: 100
Initial filter on the diameter calculation. Min/Max: 0 / 5000
A Units: ms
1207 [Diam stdy delay] Default: 0 1155,
1206
A The amount of time during which the value of Par 1206 [Diam init
filter] is kept active after the value defined in Par 1155 [Line Spd
Min/Max:
Units:
0 / 60000
ms
Thresh] has been overcome.
1171 [Variable J Comp] Default: 0.00
A Torque compensation due to the wound material as a percentage of
the drive rated current.
Min/Max:
Units:
0.00 / 199.99
%
1172 [Constant J Comp] Default: 1.00
A Compensation of the fixed section (motor, reducer, pin) as a Min/Max: – / +100.00
Winder Functions
percentage of the drive rated current. Units: %

1173 [Materl Width Pct] Default: 100.00
Width of the wound material as a percentage of the maximum width. Min/Max: 0.00 / 100.00
A Units: %
1174 [Static Friction] Default: 0.00
A Compensation
current.
for static friction as a percentage of the drive rated Min/Max:
Units:
0.00 / 199.99
%
1175 [Dynamic Friction] Default: 0.00
A Compensation
current.
for dynamic friction as a percentage of the drive rated Min/Max:
Units:
0.00 / 199.99
%

Related
Group
File
No.
1176 [Taper Enable] Default: 0= “Disabled”
Enables/Disables the Taper function. Options: 0= “Disabled”
A 1= “Enabled”
1177 [Initial Diameter] Default: 0.10
Diameter that starts the taper tension reduction. Min/Max: 0.00 / 32.00
A Units: m
1178 [Final Diameter] Default: 1.00
Diameter that ends the taper tension reduction. Min/Max: 0.00 / 32.00
A Units: m
1179 [Tension Reduct] Default: 0.00 1180
Taper tension reduction as a percentage of Par 1180 [Tension Ref]. Min/Max: 0.00 / 199.99
A Units: %
1180 [Tension Ref] Default: 0.00
A Tension reference.
Min/Max:
Units:
0.00 / 199.99
%
1181 [Tension Scale] Default: 100
A Scale factor of the torque current. This parameter is used when the
value of the maximum winding torque must be limited or when a
Min/Max:
Units:
0 / 200
%
closed loop control is used in order to adjust the torque current value
to the real tension on the material measured by the load cell.
1182 [Time AccDec Min] Default: 9.00
A The amount of time corresponding to the lower acceleration, deceler-
ation and fast deceleration time.
Min/Max:
Units:
0.15 / 300
s
1183 [Int Acc Calc En] Default: 1= “Enabled” 1182,
Enables/Disables the calculation for coil acceleration. 1184,
Winder Functions
Options: 0= “Disabled”
APPLICATIONS
• “Enabled” = This function carries out the calculation of the angular 1= “Enabled” 1185,
acceleration inside the drive. In this case it is necessary to set just 1186
A
the value of Par 1182 [Time AccDec Min].
• “Disabled” = It is necessary to set Pars 1184 [Line Accel Pct], 1185
[Line Decel Pct], 1186 [Line FastStp Pct] and 1182 [Time AccDec
Min] and to supply the corresponding status indication to the digital
inputs.
1184 [Line Accel Pct] Default: 100.00 1182
Acceleration time as a percentage Par 1182 of [Time AccDec Min]. Min/Max: 0.00 / 100.00
A Units: %
1185 [Line Decel Pct] Default: 100.00 1182
Deceleration time as a percentage of Par 1182 [Time AccDec Min]. Min/Max: 0.00 / 100.00
A Units: %
1186 [Line FastStp Pct] Default: 100.00 1182
A Fast
Min].
deceleration time as a percentage of Par 1182 [Time AccDec Min/Max:
Units:
0.00 / 100.00
%
1187 [Winder Type] Default: 0= “Winder”
A Winder/unwinder selection. If the selection is carried out via a digital
input: 0V = “Winder” , +24V = “Unwinder”.
Options: 0=
1=
“Winder”
“Unwinder”
1193 [Torq Current Pct] Default: Read Only
A Displays the amount of torque current required.
Min/Max:
Units:
0.00 / 200.00
%
1194 [Act Ten Ref Pct] Default: Read Only 1179,
1180
A Displays the percentage of tension reference less the Taper
percentage set via Par 1179 [Tension Reduct]. If the Taper function is
Min/Max:
Units:
0.00 / 199.99
%
not enabled, it corresponds to the value displayed in Par 1180
[Tension Ref].
1195 [Speed Match] Default: 0= “Off”
A Coil “launching” phase command for automatic switching.
Options: 0=
1=
“Off”
“On”

Related
Group
File
No.
1196 [Spd Match Acc] Default: 83.88
Motor acceleration time during the launching phase. Min/Max: 0.30 / 300.00
A Units: s
1197 [Spd Match Dec] Default: 83.88
A Motor deceleration time. If the motor decelerates during the launching
phase a stop command is issued.
Min/Max:
Units:
0.30 / 300.00
s
1198 [Offs Accel Time] Default: 83.88
A Ramp time for the initial phase when the machine is stopped. It refers
to Par 45 [Max Ref Speed].
Min/Max:
Units:
0.30 / 300.00
s
1199 [W Offset] Default: 0
A Speed reference offset for the initial phase of the winder/unwinder
when the line is stopped.
Min/Max:
Units:
0 / 1000
RPM
1200 [Spd Match Gain] Default: 100
A Speed reference gain during the launching phase. 100% corresponds
to a peripheral speed equal to the line speed.
Min/Max:
Units:
0 / 150
%
1201 [Winder Side] Default: 0
A Selection
• “0” = Up
of the winding/unwinding side. Min/Max: 0/1
• “1” = Down
1202 [W Gain] Default: 0
A Sets the speed reference gain used to saturate the speed loop. This
parameter is a percentage of the increasing/decreasing value of the
Min/Max:
Units:
0 / 100
%
angular speed reference.
Winder Functions
1203 [Spd Match Compl] Default: Read Only

APPLICATIONS
A Indicates a completed launching ramp. If this parameter is assigned

to a programmed digital output, it can be used to indicate that the coil
Min/Max: 0 / 32767
can be changed.
• “1” = Launching ramp completed
• “0” = Launching ramp not completed
1204 [Line Spd Source] Default: 0
Number of the sampling parameter for the line speed. Min/Max: 0 / 65535
A
1208 [Close Loop Comp] Default: Read Only
Active compensation status (output of the PID regulator). Min/Max: – / +32767
A
1209 [Torque Winder En] Default: 0= “Disabled”
Enables/disables the center winder function. Options: 0= “Disabled”
A 1= “Enabled”
1210 [W Target] Default: 0
Parameter number of the speed reference address. Min/Max: 0 / 65535
A
1213 [Actual Comp] Default: Read Only
A Active compensation status (sums up the static, dynamic and inertial
frictions) as a percentage of the drive rated current.
Min/Max:
Units:
–/+200
%
1214 [Closed Loop En] Default: 0= “Disabled”
Enables/Disables closed loop tension control (used with a load cell). Options: 0= “Disabled”
1= “Enabled”
A

Related
Group
File
No.
1215 [Speed Demand En] Default: 0= “Disabled”
A Enables/Disables the speed reference calculation for the Torque
Winder application.
Options: 0=
1=
“Disabled”
“Enabled”
1216 [Spd match torque] Default: 100
Sets the torque current during the launching and change phase. Min/Max: 0 / 200
A Units: %
1217 [W Reference] Default: Read Only 1160
A Angular speed reference.
Note: This parameter can be assigned to an analog output; 10V =
Min/Max:
Units:
–/+8192
RPM
100% of Par 45 [Max Ref Speed].
1255 [Jog TW Speed] Default: 0 1160
A Torque Winder jog reference. The parameter is entered as a
percentage of Par 1160 [Line Speed Pct].
Min/Max:
Units:
0 / 100
%
1256 [Jog TW Enable] Default: 0= “Disabled”
Winder Functions
A Enables/Disables the Torque Winder jog function. Options: 0= “Disabled”

APPLICATIONS
Note: This parameter can be assigned to a digital input. 1= “Enabled”

1284 [Ref Spd Source] Default: 0
Number of the line speed reference sampling parameter (used for Min/Max: 0 / 65535
inertia compensation and line speed reference).
A
1285 [Ref Speed Gain] Default: 0 1284
A Gain value for the line speed reference. The value of this parameter
depends on the value of Par 1284 [Ref Spd Source]. The value of [Ref
Min/Max: 0 / 32767
Speed Gain] is used to obtain a line speed reference = 100% at its

maximum value.
1286 [Ref Line Speed] Default: Read Only
Line speed percentage. Min/Max: 0.00 / 150.00
A Units: %
1287 [Static F Zero] Default: 0= “Disabled” 1286
A Enables/Disables friction compensation.
• "Enabled" = The fiction compensation value is added to all speed
Options: 0=
1=
“Disabled”
“Enabled”
values.
• "Disabled" = The static friction compensation value is added to Par
1286 [Ref Line Speed] = 1.5%.

Utility File
Related
Group

File
No.

209 [Save HIM Ref]
Enables a feature to save the present reference value issued by the HIM to drive memory when a power loss occurs. The
value is restored to the HIM at power up.
Bit 0 - “At Pwr Down” 0 = Do not save, 1 = Save at power down
At Pwr Down
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Default x x x x x x x x x x x x x x x 1
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
210 [Man Ref Preload] Default: 1= “Enabled”

Enables/disables a feature to automatically load the present “Auto” Options: 0= “Disabled”
frequency reference value into the HIM when “Manual” is selected. 1= “Enabled”
Allows smooth speed transition from “Auto” to “Manual.”
249 [Save MOP Ref]
Reference Config
Enables/Disables the feature that saves the present MOP frequency reference at power down or at stop.
• Bit 0 “At Pwr Down” - When set to “0” = Do not save, “1” = Save
• Bit 1 “At Stop” - When set to “0” = Do not save, “1” = Save
At Pwr Down
UTILITY
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
At Stop
Default x x x x x x x x x x x x x x 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1322 [Direction Mode] Default: 0= “Unipolar”

Selects the method that will be used for changing direction. Options: 0= “Unipolar”
• “Unipolar” - Drive Logic determines the direction. 1= “Bipolar”
• “Bipolar” - The sign of the reference determines the direction. 2= “Rev Disable”
• “Rev Disable” - Forward direction only (not changeable).
1375 [MOP Select] Default: 0= “Off”
Selects the destination of the MOP signal. Options: 0= ”Off”
1= “Speed Ref A”
2= “Speed Ref B”
3= “Trim Speed”
4= “TB Man Ref”
211 [Param Access Lvl] Default: 0= “Basic”
Drive Memory
Selects the parameter display level. Options: 0= “Basic”

• “Basic” = Reduced parameter set. 1= “Advanced”
• “Advanced” = Full parameter set.
258 [Reset Defaults] Default: 0= “Ready”
Setting this parameter to 1 “Factory” will load the default settings in Options: 0= “Ready”
the drive firmware. 1= “Factory”

Related
Group
File
No.
346 [Torque Positive] Default: Read Only 20
Indicates whether the drive is operating with a positive torque Min/Max: 0/1
A reference.
• 1 “Active” = The drive is operating with a positive torque reference.
The motor is accelerating in the forward direction or decelerating in
the negative direction and Par 20 [Ramp Delay] has timed out.
• 0 “Not Active” = The drive is not operating with a positive torque
reference.
347 [Torque Negative] Default: Read Only 20
Indicates whether the drive is operating with a negative torque Min/Max: 0/1
A reference.
• 1 “Active” = The drive is operating with negative torque reference.
The motor is accelerating in the reverse direction or decelerating in
the forward direction and Par 20 [Ramp Delay] has timed out.
• 0 “Not Active” = The drive is not operating with negative torque
Diagnostics
UTILITY
reference.
Note: This parameter can be assigned to a digital output and is used
for four quadrant drives only.
349 [CurrLimit Active] Default: Read Only
Indicates whether or not the drive is working within the set current Min/Max: 0/1
limits.
• 1 “Active” = The drive is currently in a current limited state.
• 0 “Not Active” =The drive is not in a current limited state.
Note: This parameter is assigned to digital output 4 (Par 148 [Digital
Out4 Sel]) by default.
372 [Spd Limit Active] Default: Read Only
Indicates whether the current speed reference value is limited by the Min/Max: 0/1
defined minimum and maximum limit values.
• 1 “Active” = The reference value is currently limited since the value
entered is out of range of the limit values defined.
• 0 “Not Active” = The reference value is within the defined limit
values.

Related
Group
File

381 [Drive Status 1] Read Only
Present operating condition of the drive.
Bit 0 “Ready” - When set (= “1”), the drive is ready
Bit 1 “Active” - When set, the drive is active
Bit 2 “Command Dir” - The direction of commanded rotation, 0 = Reverse, 1 = Forward
Bit 3 “Actual Dir” - The actual direction of the motor, 0 = Reverse, 1 = Forward
Bit 4 “Accelerating” - When set, the drive is accelerating
Bit 5 “Decelerating” - When set , the drive is decelerating
Bit 6 “Alarm” - When set, the drive is in an alarm state
Bit 7 “Fault” - When set, the drive is faulted
Bit 8 “At Speed” -When set, the drive is at the commanded speed
Bit 9 - 11 “Local ID 0-2” (1)
Bit 12-15 “Spd Ref ID 0-3” (2)
Spd Ref ID 3 (2)
Spd Ref ID 2 (2)
Spd Ref ID 1 (2)
Spd Ref ID 0 (2)
Command Dir
Decelerating
Local ID 2 (1)
Local ID 1 (1)
Local ID 0 (1)
Accelerating
Actual Dir
At Speed
Faulted
Ready
Active
Default 0 0 0 0 0 0 1 0 0 Alarm
0 0 0 1 1 0 1
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
(2) (1)
Bits Bits
15 14 13 12 Description 11 10 9 Description
0 0 0 0 Spd Ref A Auto 0 0 0 Port 0 (TB)
0 0 0 1 Spd Ref B Auto 0 0 1 DPI Port 1
0 0 1 0 Preset Spd 2 Auto 0 1 0 DPI Port 2
Diagnostics
UTILITY

0 1 1 1 Preset Spd 7 Auto 1 1 1 No Local Control
1 0 0 0 TB Manual
1 0 0 1 DPI Port 1 Manual
1 1 1 1 Jog Ref
382 [Drive Status 2] Read Only

Present operating condition of the drive.
Bit 0 “Ready” - When set (= “1”), the drive is ready
Bit 1 “Active” - When set, the drive is active
Bit 2 “Running” - When set, the drive is running
Bit 3 “Jogging” - When set, the drive is being jogged
Bit 4 “Stopping” - When set, the drive is stopping
Bit 6 “Auto Tuning” - When set, the drive is auto tuning
Auto Tuning
Curr Limit
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Stopping
Running
Jogging
Ready
Active
Default x x x x x x x x 0 0 0 0 0 0 0 1
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Related
Group
File
No.
393 [Speed Threshold] Default: Read Only 101,
Indicates if the drive is above or below the threshold speed specified Min/Max: 0/1 102,
A in parameters 101 [Speed Thresh Pos] (clockwise rotation) and 102 103
[Speed Thresh Neg] (counter-clockwise rotation).
• “0 Above Thresh” = The speed has exceeded the set speed
threshold.
• “1 Below Thresh” = The speed has not exceeded the set speed
threshold.
394 [At Speed] Default: Read Only 104,
Indicates whether or not the current speed of the drive corresponds Min/Max: 0/1 105
to the speed reference (specified in Par 118 [Speed Reg In]) before
the speed regulator and the ramp reference (if enabled) are applied.
The speed above and below the speed reference at which [At Speed]
will indicate “1 Equal” is set in Par 104 [At Speed Error].
• “0 Not Equal” - The drive is not working at the set speed reference.
• “1 Equal” - The drive is working at the set speed reference.
Note: This parameter can be assigned to a digital output. It also
corresponds to the "At Speed" indication on the Status Line of the
HIM.
395 [At Zero Speed] Default: Read Only 107,
Indicates whether or not the actual speed of the motor is below the Min/Max: 0/1 108
zero speed threshold as specified in Par 107 [Speed Zero Level].
• “0 Equal” - The actual speed is below the value of Par 107 [Speed
Diagnostics
UTILITY
Zero Level] and Par 108 [Speed Zero Delay] has timed out.
• “1 Not Equal” - The actual speed is above the value of Par 107
[Speed Zero Level].
396 [MOP Inc Active] Default: Read Only
Indicates whether or not the drive is accelerating using the Min/Max: 0/1
A preselected ramp.
• 0 “No Accel” = the drive is not accelerating using a preselected
ramp
• 1 “Accel” = the drive is accelerating using a preselected ramp
397 [MOP Dec Active] Default: Read Only
Indicates whether the drive is decelerating using the preselected Min/Max: 0/1
A ramp.
• 0 “No Decel” = The drive is not decelerating using a preselected
ramp
• 1 “Decel” = The drive is decelerating using a preselected ramp
400 [Spd Select 0] Default: Read Only 401,
Indicates the state of the assigned digital input, [Digital Inx Sel], set to Min/Max: 0/1 402
A 17 “Speed Sel 1”. Refer to Option Definitions for [Digital Inx Sel] on
page 3-66 for instructions on how to set digital input speed selects to
different speed references.
• “0” = Digital input [Digital Inx Sel] set to 17 “Speed Sel 1” not
asserted
• “1” = Digital input [Digital Inx Sel] set to 17 “Speed Sel 1” asserted
Note: By default, the state of this parameter is determined by digital
input 5.

Related
Group
File

402
A Indicates the state of the assigned digital input, [Digital Inx Sel], set to
18 “Speed Sel 2”. Refer to Option Definitions for [Digital Inx Sel] on
Min/Max: 0/1
asserted
input 6.
401
19 “Speed Sel 3”. Refer to Option Definitions for [Digital Inx Sel] on
Min/Max: 0/1
asserted
input 7.
403 [Ramp Select 0] Default: Read Only 404
25 “Acc2 & Dec2” or 26 “Accel 2”.
Min/Max: 0/1
• “0” = Accel 1 ramp rate is selected

• “1” = Accel 2 ramp rate is selected
Diagnostics
Note: This parameter can be assigned to indicate the state of a digital

UTILITY
input.
404 [Ramp Select 1] Default: Read Only 403
25 “Acc2 & Dec2” or 27 “Decel 2”.
Min/Max: 0/1
• “0” = Decel 1 ramp rate is selected

• “1” = Decel 2 ramp rate is selected
Note: This parameter can be assigned to indicate the state of a digital
input.
651 [Encoder State] Default: Read Only
A Indicates the connection status of the digital encoder or tachometer.
• “0” = Fault
Min/Max: 0/1
• ‘1” = OK
This parameter can be assigned to a digital output.
1188 [Accel Status] Default: Read Only
A Indicates the drive acceleration status.
• “0” = Off - Drive not accelerating
Min/Max: 0/1
• “1” = “On” - Drive accelerating

1189 [Decel Status] Default: Read Only
A Indicates the drive deceleration status.
• “0” = “Off” - Drive not decelerating
Min/Max: 0/1
• “1” = “On” - Drive decelerating

1190 [Fast Stop Status] Default: Read Only
A Indicates the drive fast stop status.
• “0” = “Off” - Drive is not fast stopping
Min/Max: 0/1
• “1” = “On” - Drive is fast stopping

Related
Group
File
No.
1328 [Drive Logic Rslt]
The final logic command resulting from the combination of all DPI and discrete inputs. This parameter has the same
structure as the product specific logic command received via DPI and is used in peer to peer communications. For each bit,
1=Condition true and 0=Condition false.
Bit 0 “Stop” - Stop command
Bit 1 “Start” - Start command
Bit 2 “Jog” - Jog command
Bit 3 “Clear Faults” - Clear faults command
Bit 4 “Forward” - Forward direction command
Bit 5 “Reverse” - Reverse direction command
Bit 6 “Local” - Local control command”
Bit 7 “MOP Inc” - MOP Increment command
Bit 8 “Accel 1” - Acceleration Rate 1 command
Bit 9 “Accel 2” - Acceleration Rate 2 command
Bit 10 “Decel 1” - Deceleration Rate 1 command
Bit 11 “Decel 2” - Deceleration Rate 2 command
Bit 12-14 “Spd Ref ID 0-2” - Speed reference source(1)
Bit 15 “MOP Dec” - MOP Decrement command
Spd Ref ID 2
Spd Ref ID 1
Spd Ref ID 0
Clear Faults
MOP Dec
MOP Inc
Reverse
Forward
Decel 2
Decel 1
Accel 2
Accel 1
Local
Start
Stop
Jog
Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
(1)
Bits
14 13 12 Description
Diagnostics
0 0 0 No Command - Manual Mode

UTILITY
0 0 1 Spd Ref A Auto

0 1 0 Spd Ref B Auto
0 1 1 Preset Spd 3 Auto
1381 [TestPoint Sel] Default: 566

A Selects the function whose value is displayed in [TestPoint Val].
These are internal values that are not accessible through any other
Min/Max: 566 / 574
parameters. Typically, these are internal drive variables and registers.

Refer to Testpoint Codes and Functions on page 4-14 for more
information.
1382 [TestPoint Data] Default: Read Only
The present value of the function selected in Par 1381 [Testpoint Sel]. Min/Max: -231 / 231 - 1
A
1383 [TaskLoad 32 ms] Default: Read Only
The load percentage of the 32 ms task in the firmware. Min/Max: 0.00 / 100.00
A
A
A
A
Related
Group
File

1402 [Last Stop Source] Default: Read Only
Displays the source that initiated the most recent stop sequence. Options: 0= “Pwr Removed”
1-5= “DPI Port 1-5”
6= “Reserved”
7= “Digital In”
8= “Fault”
9= “Not Enabled”
10 = “Reserved”
11 = “Jog”
12 = “Selftune”
Diagnostics
13 = “Reserved”
1403 [Start Inhibits]
Displays the inputs currently preventing the drive from starting. For each bit, 1=Inhibit condition true and 0=Inhibit condition
false.
Type 2 Alarm
Stop Assertd
Startup Actv
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
Reserved
Reserved
Reserved
Reserved
Reserved
Digital In
Enable
Fault
Default x x x 0 0 0 0 0 x 0 0 1 x 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
263 [Clear Fault Que] Default: 0= “Ready”

Allows you to clear the fault queue. Refer to Chapter 4 Options: 0= “Ready”
Troubleshooting on page 4-1 for information on clearing the fault 1= “Clr Flt Que”
queue.
1347 [Fault Clear] Default: 0= “Ready”
UTILITY
Allows you to reset drive faults and/or clear the fault queue. Options: 0= “Ready”
1= “Clear Faults”
2= “Clr Flt Que”
1348 [Fault Clr Mode] Default: 1= “Enabled”
Enables/Disables a fault reset (clear faults) attempt from any source. Options: 0= “Disabled”
This does not apply to fault codes which are cleared indirectly via 1= “Enabled”
other actions.
1349 [Status1 at Fault] 381
Captures and displays Par 381 [Drive Status 1] bit pattern at the time of the last fault. 0=Condition False, 1=Condition True.
Command Dir
Faults
Spd Ref ID 3
Spd Ref ID 2
Spd Ref ID 1
Spd Ref ID 0
Decelerating
Accelerating
Local ID 2
Local ID 1
Local ID 0
Actual Dir
At Speed
Faulted
Ready
Active
Alarm
Default 0 0 0 0 1 1 1 0 1 0 0 0 1 1 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1350 [Status2 at Fault] 382

Captures and displays Par 382 [Drive Status 2] bit pattern at the time of the last fault. 0=Condition False, 1=Condition True.
Auto Tuning
Curr Limit
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Stopping
Running
Jogging
Ready
Active
Default x x x x x x x x x 0 0 0 1 1 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Related
Group
File
No.
1351 [Fault 1 Code] Default: Read Only
1352 [Fault 2 Code]
1353 [Fault 3 Code] Min/Max: 0 / 32768
1354 [Fault 4 Code]
1355 [Fault 5 Code]
1356 [Fault 6 Code]
1357 [Fault 7 Code]
1358 [Fault 8 Code]
1359 [Fault 9 Code]
1360 [Fault 10 Code]
A code that represents the fault that tripped the drive. The codes will
A appear in these parameters in the order they occur (i.e., [Fault 1
Code] = the most recent fault). Refer to Fault Descriptions on
page 4-4 for a list of possible codes.
Note: Par 1351 [Fault 1 Code] is accessible via the Basic Parameter
view.
1361 [Fault 1 Time] Default: Read Only
1362 [Fault 2 Time]
1363 [Fault 3 Time] Min/Max: 0.000 / 134000000.000
1364 [Fault 4 Time] Units: hr.
1365 [Fault 5 Time]
Faults
1366 [Fault 6 Time]

1367 [Fault 7 Time]
1368 [Fault 8 Time]
1369 [Fault 9 Time]
1370 [Fault 10 Time]
The time between initial drive power up and the occurrence of the
A associated trip fault.
1371 [Fault Arm Amps] Default: Read Only
Captures and displays the armature current (as a percentage of rated Min/Max: –/+200
UTILITY
current) at the time of the last fault. Units: %

1372 [Fault Speed] Default: Read Only
Captures and displays the output speed (rpm) of the drive at the time Min/Max: – / +32766
of the last fault. Units: RPM
1373 [Fault Field Amps] Default: Read Only
Captures and displays the field current (as a percentage of rated Min/Max: 0.00 / 100.00
current) at the time of the last fault. Units: %
1374 [Fault Voltage] Default: Read Only
Captures and displays the armature voltage at the time of the last Min/Max: - / + 999.00
fault. Units: Vdc
203 [OverVolt Flt Cfg] Default: 2= “Fault”
Determines the response of the drive to an overvoltage condition (F5 Options: 0= “Ignore”
“Arm Overvoltage”). 1= “Alarm”
A Note: Refer to Chapter 4 for a list of alarm and fault descriptions. 2= “Fault”
354 [Aux Inp Flt Cfg] Default: 2= “Fault”

Determines the response of the drive to an external fault condition Options: 1= “Alarm”
(F2 “Auxiliary Input”), i.e., no voltage at the digital input terminal 2= “Fault”
3= “Fast Stop”
Alarms
A assigned to [Digital Inx Sel] with a value of 14 “Aux Fault”.

Notes: Refer to Chapter 4 for a list of alarm and fault descriptions. 4= “Normal Stop”
Option 3 was changed from “Quick Stop “ to “Fast Stop” with firmware 5= “CurrLim Stop”
version 2.001.
365 [OverTemp Flt Cfg] Default: 2= “Fault”
Determines the response of the drive to a motor over temperature Options: 0= “Ignore”
condition (F16 “Motor Over Temp”). 1= “Alarm”
A Notes: Refer to Chapter 4 for a list of alarm and fault descriptions. 2= “Fault”
Option 3 was changed from “Quick Stop “ to “Fast Stop” with firmware 3= “Fast Stop”
version 2.001. 4= “Normal Stop”
5= “CurrLim Stop”

Related
Group
File

473 [FldLoss Flt Cfg] Default: 2= “Fault” 497
Determines the response of the drive to a field loss condition (F6 “Fld Options: 0= “Ignore”
Current Loss”). If Par 497 [Field Reg Enable] is set to 0 “Disabled”, 1= “Alarm”
A this parameter should be set to 0 “Ignore”. 2= “Fault”
Note: Refer to Chapter 4 for a list of alarm and fault descriptions.
478 [Spd Loss Flt Cfg] Default: 2= “Fault”
Determines the response of the drive to a speed feedback loss Options: 1= “Alarm”
condition (F91 Encoder Loss). 2= “Fault”
A Note: Refer to Chapter 4 for a list of fault descriptions.
481 [UnderVolt Thresh] Default: 230

The AC input voltage level below which an undervoltage fault (F4 “AC Min/Max: 0 / 1000
A Undervoltage”) will be detected. Units: Vac
Note: Refer to Chapter 4 for a list of fault descriptions.
584 [OverCurrent Thr] Default: 175
A Value at which an overcurrent condition (F13 “Overcurrent”) will be Min/Max:
detected. Units:
0 / 250
%
Note: Refer to Chapter 4 for a list of fault descriptions.
1380 [Drive Alarm 1] 1322
Alarm conditions that currently exist in the drive. For each bit, 1=Condition true and 0=Condition false.
Bit 0 “DigInCflctA” - Digital input functions are in conflict.
Alarms
Bit 1 “DigInCflctB” - A digital Start input has been configured without a Stop input or other functions are in conflict.
Bit 2 “DigInCflctC” - More than one physical input has been configured to the same input function.
Bit 3 “BipolarCflct” - Parameter 1322 [Direction Mode] is set to “Bipolar” or “Reverse Dis” and one or more of the following
digital input functions is configured: “Fwd/Reverse,” “Run Forward,” “Run Reverse,” “Jog Forward” or “Jog Reverse.”
Bit 4 “AnalogCflct” - Analog input functions are in conflict.
Bit 5 “CntactrCflct” - Contactor input functions are in conflict.
Bit 6 “Encoder Cflc” - Indicates an encoder configuration conflict.
Bit 7 “Overvoltage” - There is an overvoltage on the armature circuit.
UTILITY
Bit 8 “Over Temp” - The motor has exceeded its temperature rating (as signaled by the thermistor connected to the drive
terminals 78 and 79).
Bit 9 “Aux Input” - An auxiliary input interlock is open or a voltage (15 - 30 V) or reference signal is missing for the digital
input set to 14 “Aux Fault”.
Bit 10 “Field Loss” - The field current is too low.
Bit 11 “Encoder Loss” - The drive is not receiving a speed feedback signal.
Bit 12 “PwrUp Start” - Indicates that the drive is starting or has automatically resumed running at commanded speed after
drive input power is restored.
Note: Refer to Chapter 4 Troubleshooting on page 4-1 for information.
Encoder Loss
Encoder Cflc
PwrUp Start
Overvoltage
CntactrCflct
AnalogCflct
BipolarCflct
DigInCflctC
DigInCflctB
DigInCflctA
Over Temp
Field Loss
Reserved
Reserved
Reserved
Aux Input
Default x x x x x 0 0 0 0 0 0 0 0 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
50 [UsrDsplyMult0] Default: 1
Numerator in the calculation for user-defined, drive speed display Min/Max: 1 / 1073741823
units.
A Note: This parameter is not used.
User Defined
51 [UsrDsplyDiv0] Default: 1
Denominator in the calculation for user-defined, drive speed display Min/Max: 1 / 1073741823
units.
A Note: This parameter is not used.
53 [UsrValMult1] Default: 1
Numerator in the calculation for scaling the user-defined, drive speed Min/Max: 1 / 32767
A display units.
Note: This parameter is not used.

Related
Group
File
No.
54 [UsrValDiv1] Default: 1
Denominator in the calculation for scaling the user-defined, drive Min/Max: 1 / 32767
A speed display units.
Note: This parameter is not used.
503 [UserDefined0] Default: 0
504 [UserDefined1]
505 [UserDefined2] Min/Max: –32768/+32767
506 [UserDefined3]
507 [UserDefined4]
508 [UserDefined5]
509 [UserDefined6]
510 [UserDefined7]
511 [UserDefined8]
512 [UserDefined9]
513 [UserDefined10]
514 [UserDefined11]
515 [UserDefined12]
516 [UserDefined13]
517 [UserDefined14]
518 [UserDefined15]
General use signed 16 bit variables used for data exchange.
A Note: Pars 503–506 can be assigned to analog inputs. The values of
Pars 503, 504, and 507 - 509 can be assigned to an analog output.
User Defined
519 [UsrDefBitWrdA] Default: 0 520 -

UTILITY
A bitmap of Pars 520 [UsrDefBitWrdA0] through 535 Min/Max: 0 / 65535 535

A [UsrDefBitWrdA15]. With a parameter it is possible to read or write all
of the bits inside a word.
Example:
[UsrDefBitWrdA0] 0
[UsrDefBitWrdA1] 1 = 21 =2
[UsrDefBitWrdA2] 0
[UsrDefBitWrdA3] 0
[UsrDefBitWrdA4] 0
[UsrDefBitWrdA5] 1 = 25 = 32
[UsrDefBitWrdA7] 0
[UsrDefBitWrdA8] 0
[UsrDefBitWrdA9] 0
[UsrDefBitWrdA11] 0
[UsrDefBitWrdA13] 0
[UsrDefBitWrdA14] 0
[UsrDefBitWrdA15] 0
[UsrDefBitWrdA] = 2 + 32 + 64 + 1024 + 4096 = 5218
Note: This parameter can be assigned to a digital input or output. The
bit number corresponds to the digital input/output number (e.g.,
digital input 3 uses [UsrDefBitWrdA3]). Relay Outputs 1 and 2 use
bits 14 and 15, respectively.

Related
Group
File

520 [UsrDefBitWrdA0] Default: 0 519
521 [UsrDefBitWrdA1]
522 [UsrDefBitWrdA2] Min/Max: 0/1
User Defined
UTILITY
Bit variables. The individual "User Defined" bits can be read or written
A to. It is possible to process a word with Par 519 [UsrDefBitWrdA] (see
example).
Note: You can read bits 0-7 of a digital input with Par 519
[UsrDefBitWrdA] and write all of the bits associated with
[UsrDefBitWrdA] to a digital output.

Related
Group
File
No.
536 [UsrDefBitWrdB] Default: 0 537 -
A bitmap of Pars 537 [UsrDefBitWrdB0] through 552 Min/Max: 0 / 65535 552
A [UsrDefBitWrdB15]. With a parameter it is possible to read or write all
of the bits inside a word.
Example:
[UsrDefBitWrdB0] 0
[UsrDefBitWrdB1] 1 = 21 =2
[UsrDefBitWrdB2] 0
[UsrDefBitWrdB3] 0
[UsrDefBitWrdB4] 0
[UsrDefBitWrdB5] 1 = 25 = 32
[UsrDefBitWrdB7] 0
[UsrDefBitWrdB8] 0
[UsrDefBitWrdB9] 0
[UsrDefBitWrdB11] 0
[UsrDefBitWrdB13] 0
[UsrDefBitWrdB14] 0
[UsrDefBitWrdB15] 0
User Defined
[UsrDefBitWrdB] = 2 + 32 + 64 + 1024 + 4096 = 5218

UTILITY
Note: This parameter can be assigned to a digital input or output. The

bit number corresponds to the digital input/output number (e.g.,
digital input 3 uses [UsrDefBitWrdA3]). Relay Outputs 1 and 2 use
bits 14 and 15, respectively.
537 [UsrDefBitWrdB0] Default: 0 536
538 [UsrDefBitWrdB1]
539 [UsrDefBitWrdB2] Min/Max: 0/1
Bit variables. The individual “User Defined” bits can be read or written
A to. It is possible to process a word with Par 536 [UsrDefBitWrdB]. See
the example in Par 536 [UsrDefBitWrdB].
Note: You can read bits 0-7 of a digital input with Par 536
[UsrDefBitWrdB] and write all of the bits associated with
[UsrDefBitWrdB] to a digital output.

Communications File
Related
Group

File
No.

589 [DPI Baud Rate] Default: Read Only
Shows the data transfer rate for attached drive peripherals. Min/Max: 1/1
“1” - 500 kbps
590 [DPI Port Sel] Default: 1 “DPI Port 1” 1343
Selects which DPI port reference value (unscaled) will Options: 1= “DPI Port 1”
appear in Par 1343 [DPI Port Value]. 2= “DPI Port 2”
Comm Control
3= “DPI Port 3”
4= “DPI Port 4”
5= “DPI Port 5”
1321 [DPI Fdbk Select] Default: 0= “Speed”
Selects the feedback variable and DPI units displayed on the Options: 0= “Speed”
feedback line of the HIM. 1= “Current”
• 0 “Speed” = Speed feedback units are in RPM
• 1 “Current” = Current feedback units are in %
1343 [DPI Port Value] Default: Read Only 590
Unscaled value of the DPI reference selected in Par 590 [DPI Min/Max: –/+32767
Port Sel].
591 [Logic Mask]
Reserved.
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
COMMUNICATIONS
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Digital In
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
592 [Start Mask] See [Logic Mask]

Controls which adapters can issue start commands.
Masks & Owners
593 [Jog Mask] See [Logic Mask]

Controls which adapters can issue jog commands.
594 [Direction Mask] See [Logic Mask]
Controls which adapters can issue forward/reverse direction
commands.
595 [Reference Mask] See [Logic Mask]
Controls which adapters can select a manual reference.
596 [Accel Mask] See [Logic Mask] 24,
Controls which adapters can select the acceleration ramp 660
rates (Pars 660 [Accel Time 1] and 24 [Accel Time 2]) of the
drive.
597 [Fault Clr Mask] See [Logic Mask]
Controls which adapters can clear a fault.
598 [MOP Mask] See [Logic Mask]
Controls which adapters can issue MOP commands to the
drive.

Related
Group
File
No.
599 [Local Mask] See [Logic Mask]
Controls which adapters are allowed to take exclusive control
of drive logic commands (except stop). Exclusive “local”
control can only be taken while the drive is stopped.
600 [Stop Owner]
The adapters that are presently issuing a valid stop command. 0 = No Command, 1 = Issuing Command, x = Reserved.
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Digital In
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
601 [Start Owner] See [Stop Owner]

The adapters that are presently issuing a valid start
command.
602 [Jog Owner] See [Stop Owner]
The adapters that are presently issuing a valid jog command.
603 [Direction Owner] See [Stop Owner]
The adapter that currently has exclusive control of direction
changes.
COMMUNICATIONS
Masks & Owners
604 [Reference Owner] See [Stop Owner]

The adapter that has the exclusive control of the command
frequency source selection.
605 [Accel Owner] See [Stop Owner] 24,
The adapter that has exclusive control of the acceleration 660
ramp rate (Pars 660 [Accel Time 1] and 24 [Accel Time 2]) for
the drive.
606 [Fault Clr Owner] See [Stop Owner]
Adapter that is presently clearing a fault.
607 [MOP Owner] See [Stop Owner]
Adapters that are currently issuing increases or decreases in
MOP command frequency.
608 [Local Owner] See [Stop Owner]
Adapter that has requested exclusive control of all drive logic
functions. If an adapter is in local lockout, all other functions
(except stop) on all other adapters are locked out and non–
functional. Local control can only be obtained when the drive
is not running.
609 [Decel Owner] See [Stop Owner] 32,
The adapter that has exclusive control of the deceleration 662
ramp rate (Pars 662 [Decel Time 1] and 32 [Decel Time 2])
for the drive.
631 [Decel Mask] See [Logic Mask] 32,
Controls which adapters can select the deceleration ramp 662
rate (Pars 662 [Decel Time 1] and 32 [Decel Time 2]) of the
drive.

Related
Group Parameter Name & Description
File
No.
610 [Data In A1] – Link A Word 1 Default: 0 (0 = “Disabled”)
611 [Data In A2] – Link A Word 2
Min/Max: 0 / 1408
Parameter number whose value will be written from a
communications device data table. The value will not be
updated until the drive is stopped.
Refer to your communications option manual for datalink
information.
612 [Data In B1] – Link B Word 1 See [Data In A1] – Link A Word 1.
613 [Data In B2] – Link B Word 2
614 [Data In C1] – Link C Word 1 See [Data In A1] – Link A Word 1.
615 [Data In C2] – Link C Word 2
616 [Data In D1] – Link D Word 1 See [Data In A1] – Link A Word 1.
Datalinks
617 [Data In D2] – Link D Word 2
618 [Data Out A1] – Link A Word 1 Default: 0 (0 = “Disabled”)

619 [Data Out A2] – Link A Word 2
Min/Max: 0 / 1408
Parameter number whose value will be written to a
communications device data table.
620 [Data Out B1] – Link B Word 1 See [Data Out A1] – Link A Word 1.
621 [Data Out B2] – Link B Word 2
622 [Data Out C1] – Link C Word 1 See [Data Out A1] – Link A Word 1.
623 [Data Out C2] – Link C Word 2
COMMUNICATIONS
624 [Data Out D1] – Link D Word 1 See [Data Out A1] – Link A Word 1.
625 [Data Out D2] – Link D Word 2
1319 [Data In Val Sel] Default: 610 1320
Selects the Datalink parameter register to display in Par 1320 Min/Max: 610 / 617
[Data In Sel Data].
1320 [Data In SelData] Default: Read Only 1319
Displays the value selected in Par 1319 [Data In Val Sel]. Min/Max: - / +231
591 [Logic Mask]
Reserved.
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Digital In
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Security
1376 [Logic Mask Act] Read Only 591

Indicates the status of the logic mask for the DPI ports. When bit 15 is set,
A network security is controlling the logic mask instead of Par 591 [Logic Mask].
0 = Control Masked, 1 = Control Permitted, x = Reserved.
Aux Port 14
Aux Port 13
Aux Port 12
Aux Port 11
Aux Port 10
Aux Port 9
Aux Port 8
Aux Port 7
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
Advanced
Reserved
Digital In
Default 0 x x x x x x x x x 1 1 1 1 1 1
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Related
Group
File
No.
1377 [Write Mask Act] Read Only 1378
The status of write access for the DPI ports. When bit 15 is set, network
A security is controlling the write mask instead of Par 1378 [Write Mask Cfg]. 0 =
Read Only, 1 = Write Permitted, x = Reserved.
Aux Port 14
Aux Port 13
Aux Port 12
Aux Port 11
Aux Port 10
Aux Port 9
Aux Port 8
Aux Port 7
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
Advanced
Reserved
Digital In
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1378 [Write Mask Cfg] 1377

Enables/Disables parameter write access for the DPI ports. Masking of the Port that is writing to this parameter is
prohibited.
COMMUNICATIONS
A 0 = Read Only, 1 = Write Permitted, x = Reserved.

Security
Aux Port 14
Aux Port 13
Aux Port 12
Aux Port 11
Aux Port 10
Aux Port 9
Aux Port 8
Aux Port 7
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
Reserved
Reserved
Digital In
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
1379 [Port Mask Act] Read Only

Bits 0–5 indicate status for DPI port communication. Bit 15 indicates when
A security software is controlling the parameter. 0 = Not Active, 1 - Active, x -
Reserved.
Aux Port 14
Aux Port 13
Aux Port 12
Aux Port 11
Aux Port 10
Aux Port 9
Aux Port 8
Aux Port 7
DPI Port 5
DPI Port 4
DPI Port 3
DPI Port 2
DPI Port 1
Reserved
Security
Host
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Input / Output File
Related
Group

File
No.

70 [Anlg In1 Sel] Default: 1= “Speed Ref A”
75 [Anlg In2 Sel] Default: 0= “Off”
80 [Anlg In3 Sel] Default: 0= “Off”
Selects the parameter to which a value will be written from the
analog input. Options:
0= “Off” (No signal) 9= “Neg Cur Lim” (Par 9) 18 = “PI CentralV3” (Par 778)
1= “Speed Ref A” (Par 44) 10 = “Jog Ref” (Par 266) 19 = “PID Feedback” (Par 763)
2= “Speed Ref B” (Par 48) 11 = “Adaptive Ref” (Par 183) 20 = “Fld Cur Max” (Par 467)
3= “Trim Ramp” (Par 42) 12 = “UserDefined0” (Par 503) 21 = “OutVoltLevel” (Par 233)
4= “Trim Speed” (Par 43) 13 = “UserDefined1” (Par 504) 22 = “Speed Ratio” (Par 1017)
5= “Torque Ref” (Par 39) 14 = “UserDefined2” (Par 505) 23 = “Tension Red” (Par 1179)
6= “Trim Torque” (Par 40) 15 = “UserDefined3” (Par 506) 24 = “Tension Ref” (Par 1180)
7= “TB Man Ref” (Par 267) 16 = “Load Comp” (Par 698) 25 = “Diam Preset3” (Par 1167)
8= “Pos Cur Lim” (Par 8) 17 = ‘PID Setpt 0” (Par 760)
71 [Anlg In1 Config] Default: 0= “+/–10V” 1322

76 [Anlg In2 Config]
81 [Anlg In3 Config] Options: 0= “+/–10V”
1= “0-10V”
Selects the signal input (voltage or current) mode for the analog 2= “0 - 20mA”
input. Configure switches S9, S10, and S11 on the Control 3= “4 to 20mA”
board according to the input signal used. The inputs of the drive
INPUT / OUTPUT
are factory set for voltage signals. Refer to DIP Switch and
Analog Inputs
Jumper Settings on page 1-32 for information on switch

configuration.
• “+/–10V” = A maximum voltage of ±10V is connected to the
analog input. If the signal is used as a reference value, a
polarity reversal can be used to reverse the rotation direction
of the drive (four quadrant only) when Par 1322 [Direction
Mode] = 1 “Bipolar”. Two quadrant drives accept only positive
references as the speed reference. Negative references are
not accepted and the drive will run at zero speed.
• “0-10V” = A maximum voltage of 10V is connected to the
analog input. For reference values, only positive references
are allowed.
• “0 - 20mA” = A maximum current signal of 0 – 20 mA is
connected to the analog input. The signal must be positive.
• “4 to 20mA” = A current signal of 4 – 20 mA is connected to
the analog input. The signal must be positive.
72 [Anlg In1 Scale] Default: 1.00
77 [Anlg In2 Scale]
82 [Anlg In3 Scale] Min/Max: –/+10.00
Scales the value in the corresponding [Anlg Inx Sel] parameter.
A
73 [Anlg1 Tune Scale] Default: 1.00
78 [Anlg2 Tune Scale]
83 [Anlg3 Tune Scale] Min/Max: 0.10 / 10.00
Fine tuning of the analog input when the maximum signal does
A not correspond exactly to the rated value. Scales according to
the following equation:
[Anlg Inx Sel] – [Anlg Inx Offset] x [Anlg Inx Scale] x [Ainx Tune
Scale]

Related
Group
File
No.
74 [Anlg In1 Offset] Default: 0
79 [Anlg In2 Offset]
84 [Anlg In3 Offset] Min/Max: –32768/+32767
Offset value for the analog inputs. If the input has an offset or if
A the variable assigned to the input already has a value although
there is no input signal present, this can be compensated for via
the value in this parameter.
259 [Anlg In1 Tune] Default: 0= “Ready”
260 [Anlg In2 Tune]
261 [Anlg In3 Tune] Options: 0= “Ready”
1= “Tune”
Automatic fine tuning of the analog inputs. If this command is
A given, parameter [Ainx Tune Scale] is automatically selected so
that the input signal present, normally full scale, corresponds to
the maximum variable value, such as the value of Par 45 [Max
Ref Speed]. Two conditions are necessary for automatic fine
tuning:
• An input voltage greater than 1V or an input current greater
than 2 mA.
• Positive polarity. The value found is automatically set for the
opposite direction for four quadrant drives.
Note: The automatically calculated value can, if necessary, be
modified manually via parameter [Ainx Tune Scale]. When using
analog input tuning, Pars [Analog Inx Scale] are normally set to
1.0.
295 [Anlg In1 Target] Default: 0= “Assigned”
296 [Anlg In2 Target]
297 [Anlg In3 Target] Options: 0= “Assigned”
1= “Not Assigned”
Enables sampling for the analog inputs.
INPUT / OUTPUT
792 [Anlg In1 Filter] Default: 0

Analog Inputs
Analog input 1 filter. Min/Max: 0 / 1000

A Units: ms
1042 [Anlg In1 Cmp] Default: 0 1043,
Defines a reference point for the signal of analog input 1 around Min/Max: – / +10000 1044,
which a comparison range can be set (via Par 1043 [Anlg In1 1045
Cmp Err]) and monitored.
[Anlg In1 Cmp] = (comparison value) x 10000 / (max. reference
value), where the values of “comparison” and “max. reference”
are determined by the min/max of the related parameter
selected via Par 70 [Anlg In1 Sel].
1043 [Anlg In1 Cmp Err] Default: 0 1042,
Defines a value above and below the value set in parameter Min/Max: 0 / 10000 1044,
1042 [Anlg In1 Cmp] at which Par 1045 [Anlg In1 Cmp Eq] will 1045
transition.
[Anlg In1 Cmp Err] = (tolerance value) x 10000 / (max. reference
value), where the values of “tolerance” and “max. reference” are
determined by the min/max of the parameter selected via Par 70
[Anlg In1 Sel].
1044 [Anlg In1 Cmp Dly] Default: 0 1042,
Amount of time that must elapse, after the value in Par 1043 Min/Max: 0 / 65000 1043,
[Anlg In1 Cmp Err] has been reached, before Par 1045 [Anlg In1 Units: ms 1045
Cmp Eq] transitions.
1045 [Anlg In1 Cmp Eq] Default: Read Only 1042,
Provides an indication, after the amount of time specified in Par Min/Max: 0/1 1043,
1044 [Anlg In1 Cmp Dly] has elapsed, when the value set in 1044
parameter 1043 [Anlg In1 Cmp Err] has been reached.
• “0” = The value of analog input 1 is above or below the value
set in Par 1043 [Anlg In1 Cmp Err].
• “1” = The value of analog input 1 is within the range set in Par
1043 [Anlg In1 Cmp Err].

Related
Group
File
No.
1404 [Analog In1 Value] Default: Read Only 71
Value of the signal at analog input 1. Units based on the value Min/Max: -/+20.00
set in Par 71 [Anlg In1 Config]. Units: V or mA
Analog Inputs

62 [Anlg Out1 Scale] Default: 1.00
63 [Anlg Out2 Scale]
64 [Anlg Out3 Scale] Min/Max: –/ +10.00
65 [Anlg Out4 Scale]
Scaling of the analog outputs.
66 [Anlg Out1 Sel] Default: 12 = “Motor Speed”
67 [Anlg Out2 Sel] Default: 13 = “Motor Curr”
68 [Anlg Out3 Sel] Default: 18 = “Fld Current”
69 [Anlg Out4 Sel]* Default: 14 = “Motor Volts”
INPUT / OUTPUT
Selects the source of the value that drives the analog output.
*This parameter is used to configure the analog output on the
I/O Expansion circuit board.
Options:
Analog Outputs
0= “Off” (Not used) 12 = “Motor Speed” (Par 121)(1) 24 = “Field Ref” (Par 500)
1= “Spd Ref Out” (Par 385) 13 = “Motor Curr” (Par 199)(2) 25 = “PID Output” (Par 774)
2= “Trim Ramp” (Par 42) 14 = “Motor Volts” (Par 233) 26 = “Out Volt Lvl” (Par 921)
3= “Ramp In” (Par 110) 15 = “Analog In 1” (Par 70) 27 = “Fld Cur Max” (Par 467)
4= “Ramp Out” (Par 113) 16 = “Analog In 2” (Par 75) 28 = “Filtered Spd” (Par 924)(1)
5= “Spd Draw Out” (Par 1018) 17 = “Analog In 3” (Par 80) 29 = “Filtered Cur” (Par 928)(2)
6= “Trim Speed” (Par 43) 18 = “Fld Current” (Par 234) 30 = “Output Power” (Par 1052)(3)
7= “Spd Reg In” (Par 118) 19 = “UserDefined0” (Par 503) 31 = “Roll Diam” (Par 1154)(4)
8= “Spd Reg Out” (Par 236) 20 = “UserDefined1” (Par 504) 32 = “Tension Ref” (Par 1180)
9= “Torque Ref” (Par 39) 21 = “UserDefined4” (Par 507) 33 = “Torque Curr” (Par 1193)(2)
10 = “Trim Torque” (Par 40) 22 = “UserDefined5” (Par 508) 34 = “Winder Ref” (Par 1217)(1)
11 = “Torq Reg In” (Par 41) 23 = “UserDefined6” (Par 509) 35 = “Active Comp” (Par 1213)(2)
(1) ±10V = 100% of Par 45 [Max Ref Speed].

(2) ±10V = ± 200% of Par 179 [Nom Mtr Arm Amps].
(3) ±10V = ± 200% of Par 179 [Nom Mtr Arm Amps] x Par 233 [Output Voltage].
(4) As a percentage of Par 1153 [Max Diameter].

Related
Group
File
No.
133 [Digital In1 Sel] Default: 2= “Stop/CF”
134 [Digital In2 Sel] Default: 3= “Start”
135 [Digital In3 Sel] Default: 11 = “Jog”
136 [Digital In4 Sel] Default: 1= “Enable”(1)
137 [Digital In5 Sel] Default: 17 = “Speed Sel 1”
140 [Digital In8 Sel] Default: 31 = “Contactor”
141 [Digital In9 Sel]* Default: 0= “Not Used”
Selects the function driven by the digital input.
Refer to Option Definitions for [Digital Inx Sel] on page 3-66.
*These parameters are used to configure the digital inputs on
the I/O Expansion circuit board.
Note: Option 35 was changed from “Fld Weaken En” to “Force
MinFld” and option 64 “Invert Flt” was added with firmware
version 2.001.
Options:
INPUT / OUTPUT
Digital Inputs
0= “Not Used” 17 = “Speed Sel 1” 34 = “Field Reg En” 51 = “Diam Reset”

1= “Enable”(1) (2) 18 = “Speed Sel 2” 35 = “Force MinFld” 52 = “DiamCalc Dis”
2= “Stop/CF” (2) 19 = “Speed Sel 3” 36 = “Freeze Ramp” 53 = “Torq Wind En”
3= “Start” (2) 20 = “PI Enable” 37 = “UsrDefinedA0” 54 = “Speed Match”
4= “Fwd/Reverse” (2) 21 = “PI Hold” 38 = “UsrDefinedA1” 55 = “Diam I/D En”
5= “Run” (2) 22 = “PI Reset” 39 = “UsrDefinedA2” 56 = “Wind/Unwind”
6= “Run Forward” (2) 23 = “PI Invert” 40 = “UsrDefinedA3” 57 = “Diam Preset0”
7= “Run Reverse” (2) 24 = “Local” 41 = “UsrDefinedA4” 58 = “Diam Preset1”
8= “Run Level” (2) 25 = “Acc2 & Dec2” 42 = “UsrDefinedA5” 59 = “Taper Enable”
9= “RunFwd Level” (2) 26 = “Accel 2” 43 = “UsrDefinedA6” 60 = “Spd DemandEn”
10 = “RunRev Level” (2) 27 = “Decel 2” 44 = “UsrDefinedA7” 61 = “Winder Side”
11 = “Jog” (2) 28 = “MOP Inc” 45 = “Droop Enable” 62 = “PI-PD Enable”
12 = “Jog Forward” (2) 29 = “MOP Dec” 46 = “PD Enable” 63 = “Jog TW En”
13 = “Jog Reverse” (2) 30 = “Fast Stop” 47 = “PID SetptSel” 64 = “Invert Flt”
14 = “Aux Fault” 31 = “Contactor” 48 = “PI Cent vs0”
15 = “Clear Faults” 32 = “MOP Reset” 49 = “PI Cent vs1”
16 = “Auto/Manual” 33 = “TorqueReduce” 50 = “Diam Calc”
1 A digital input (1-8 only) must be configured for “Enable”.
2 This option is not available (“Reserved”) for digital inputs 9 - 12.

Related
Group
File
No.
Option Definitions for [Digital Inx Sel]
Note: When assigning digital inputs to certain options that are associated with parameters, those parameter values may be overwritten by the state
of the digital input.
Option Description
Enable(1)(2) Asserting the input causes the motor to coast-to-stop without generating a fault.
Stop/CF(2) Stops the drive if running or jogging or clears a fault if the drive is already stopped.
Start(2) Issues a Start command, removal does not Stop the drive (3-wire control).
Fwd/Reverse(2) Selects the operating direction of the drive.
Run(2) Issues a Start command, removal causes the drive to Stop (2-wire control).
Run Forward(2) Issues a Run command in the Forward direction.
Run Reverse(2) Issues a Run command in the Reverse direction.
Run Level(2) Level sensitive Run command (no off-to-on transition required).
RunFwd Level(2) Run Level command in the Forward direction.
RunRev Level(2) Run Level command in the Reverse direction.
Jog(2) Starts the drive and runs at the speed in Par 266 [Jog Speed], removal causes the drive to Stop.
Jog Forward(2) Issues a Jog command in the Forward direction.
Jog Reverse(2) Issues a Jog command in the Reverse direction.
Aux Fault Asserting causes an Auxiliary Input fault (F2).
Clear Faults Issues a Clear Faults command.
Auto/Manual Selects between Automatic and Manual speed reference values.
Speed Sel 1 - 3 Selects one of eight speed references. Bit enumerations: 000 = Par 44 [Speed Ref A], 001 = Par 48 [Speed Ref B], 010 = Par 155 [Preset Speed 2], 011
= Par 156 [Preset Speed 3], 100 = Par 157 [Preset Speed 4], 101 = Par 158 [Preset Speed 5], 110 = Par 159 [Preset Speed 6], 111 = Par 160 [Preset
Speed 7]
PI Enable Enables/disables the PI block of the PID regulator (Par 769 [Enable PI]).
PI Hold Enables/disables a hold on the PI output.
PI Reset Asserting causes a reset of the PI output.
PI Invert Asserting causes an inversion of the PI output.
Local Enables exclusive drive control via the I/O Terminal Block only.
Acc2 & Dec2 Switches between the Accel/Decel 1 and Accel/Decel 2 ramp rates.
INPUT / OUTPUT
Accel 2 Switches between the Accel 1 and Accel 2 ramp rates.

Digital Inputs
Decel 2 Switches between the Decel 1 and Decel 2 ramp rates.

MOP Inc Asserting causes the MOP reference to increment at the rate set in Par 22 [MOP Accel Time].
MOP Dec Asserting causes the MOP reference to decrement at the rate set in Par 30 [MOP Decel Time].
Fast Stop Causes the drive to Stop at the rate set in Par 38 [Fast Stop Time].
Contactor Indicates the status of the main contactor/DB contactor. Must be assigned and asserted in order to run drive when Par 1391 [ContactorControl] =
“Contactor” or “Contactor+DB”.
MOP Reset Asserting resets the MOP reference to zero.
TorqueReduce Turns on /off Torque Reduction using the reduced current limit set in Par 13 [Torq Red CurLim].
Field Reg En Enables/disables the field regulator (Par 497 [Field Reg Enable])
Force MinFld When asserted, the field current is set to the value specified in Par 498 [Force Min Field].
Freeze Ramp Holds the speed ramp at the present value (Par 373 [Freeze Ramp]).
UsrDefinedA0-7 Writes the value of the digital input to Pars 520 [UsrDefBitWrdA0] - 527 [UsrDefBitWrdA7].
Droop Enable Enables/disables the Droop function (699 [Enable Droop]).
PD Enable Enables/disables the PD block of the PID regulator (Par 770 [Enable PD]).
PI Cent vs0 - 1 In combination, the digital inputs set to “PI Central vs0” and “PI Central vs1”, through binary selection, determine which of the four possible output values
is used as the initial level of the integral component (corresponding to the initial diameter) of the PI block. Refer to Par 780 [PI Central vs0] for binary
selection values.
Diam Calc When asserted initiates the diameter calculation (Par 794 [Diameter Calc]).
Diam Reset Sets the diameter starting value to the value in Par 1168 [Diam Preset Sel].
DiamCalc Dis Enables/disables the diameter calculation (Par 1161 [Diameter Calc Dis]).
Torq Wind En Enables/disables the Center wind function (Par 1209 [Torque Winder En]).
Speed Match When asserted, issues the coil 'launch phase' command for automatic switching (Par 1195 [Speed Match]).
Diam I/D En Enables/disables the ability of the diameter calculation to increase for an unwider or decrease for a winder (Par 1205 [Diam Inc Dec En]).
Wind/Unwind Sets the value of Par 1187 [Winder Type] to “0” Winder or “1” Unwinder .
Diam Preset0 - 1 Selects the value of Par 1164 [Diam Preset 0], 1165 [Diam Preset 1], Par 1166 [Diam Preset 2], or Par 1167 [Diam Preset 3] See Par 1168 [Diam Preset
Sel].
Taper Enable Enables/disables the Taper function (Par 1176 [Taper Enable]).
Spd DemandEn Enables/disables the speed reference calculation (winder operation), (Par 1215 [Speed Demand En]).
Winder Side Selection of the winding/unwinding side (0 = up, 1 = down).
PI-PD Enable Selection between PI and PD (winder operation), (Par 1201 [Winder Side]).
Jog TW En Enables/disables the Torque Winder jog function (Par 1256 [Jog TW Enable]).
Invert Flt Must be used when the digital input is wired to the status of an inverting fault device (fuse, circuit breaker, etc.). When asserted, causes an “Inverting
Fault” (F37). Refer to Figure 1.13 on page 1-19 for more information.
1 A digital input (1-8 only) must be configured for “Enable”.
2 This option is not available (“Reserved”) for digital inputs 9 - 12.

Related
Group
File
No.
564 [Dig In Status] Read Only
Status of the digital inputs.
Digital In12
Digital In11
Digital In10
Digital In9
Digital In8
Digital In7
Digital In6
Digital In5
Digital In4
Digital In3
Digital In2
Digital In1
Reserved
Reserved
Reserved
Reserved
Default x x x x 0 0 0 0 0 0 0 0 0 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
565 [Dig In Term 1] Default: Read Only

566 [Dig In Term 2]
567 [Dig In Term 3] Min/Max: 0/1
568 [Dig In Term 4]
569 [Dig In Term 5]
570 [Dig In Term 6]
571 [Dig In Term 7]
572 [Dig In Term 8]
573 [Dig In Term 9]
574 [Dig In Term 10]
Status of the digital inputs.
0 = Low
1 = High
1276 [Inversion In 1] Default: 0 “Disabled”
1277 [Inversion In 2]
Options: 0= “Disabled”
INPUT / OUTPUT
1= “Enabled”
Digital Inputs
inverts the digital input signal.
A
1391 [ContactorControl] Default: 1= “AC Cntctr”
Selects the type of contactor to be controlled by the drive. Either
Options: 0= “None”
style of contactor (AC or DC) can be used, with or without 1= “AC Cntctr”
dynamic braking (DB) contactor. 2= “AC Cntctr+DB”
A • “AC Cntctr” indicates an AC contactor is used 3= “DC Cntctr”
• “AC Cntctr+DB” indicates that an AC contactor and dynamic 4= “DC Cntctr+DB”
brake resistor is used
• “DC Cntctr” indicates a DC contactor is used
• “DC Cntctr+DB” indicates that a DC contactor and dynamic
brake resistor is used
The type of control selected determines how many I/O points
will be required for contactor control and status.
• “AC Cntctr” or “DC Cntctr” = 1 (relay) digital output, 1 digital
input is used
• “AC Cntctr+DB” or “DC Cntctr+DB” = 2 (relay) digital outputs,
1 digital input is used
Note: Options 1 and 2 changed from “Contactor” and
“Contactor+DB” to “AC Cntctr” and AC Cntctr+DB”, respectively,
and options 3 and 4 added with firmware version 2.001.

Related
Group
File
No.
145 [Digital Out1 Sel] Default: 5= “Ready”
146 [Digital Out2 Sel] Default: 9= “Fault”
147 [Digital Out3 Sel] Default: 2= “Spd Thresh”
148 [Digital Out4 Sel] Default: 4= “CurrentLimit”
149 [Digital Out5 Sel]* Default: 26 = “Alarm”
150 [Digital Out6 Sel]* Default: 0= “Not Used”
Selects the source of the value that drives the digital output.
Refer to “Option Definitions” on Option Definitions for [Digital
Outx Sel], [Relay Out 1 Sel] and [Relay Out 2 Sel] on page 3-69.
INPUT / OUTPUT
Digital Outputs
*These parameters are used to configure the digital outputs on

the I/O Expansion circuit board.
Options:
0= “Not Used” 8= “Spd Limited” 16 = “Encoder Err” 24 = “Reserved”

1= “Spd Zero Thr” 9= “Fault” 17 = “Diam Calc” 25 = “Reserved”
2= “Spd Thresh” 10 = “Power Loss” 18 = “Input1 Cmp” 26 = “Alarm”
3= “At Speed” 11 = “UserDefinedA” 19 = “Diam Reached” 27 = “Running”
4= “CurrentLimit” 12 = “UserDefinedB” 20 = “Speed Match” 28 = “Jogging”
5= “Ready” 13 = “Stop Control” 21 = “Accelerating” 29 = “Active”
6= “Ramp Pos” 14 = “Field Loss” 22 = “Decelerating”
7= “Ramp Neg” 15 = “Spd Fbk Loss” 23 = “Brake Cmd”

Related
Group
File
No.
Option Definitions for [Digital Outx Sel], [Relay Out 1 Sel] and [Relay Out 2 Sel]
Option Description
Spd Zero Thr “0” indicates that the drive is operating below the value set in Par 107 [Speed Zero Level] , “1”
indicates that the drive is operating above Par 107 [Speed Zero Level].
Spd Thresh “0” indicates that the drive is operating above the value set in Par 101 [Speed Thresh Pos], “1”
indicates that the drive is operating below Par 101 [Speed Thresh Pos].
At Speed “0” indicates that the actual speed is within the range specified in Par 104 [At Speed Error], “1”
indicates that the actual speed is outside the range specified in Par 104 [At Speed Error].
CurrentLimit “0” indicates that the drive is not limiting output current, “1” indicates that the drive is limiting the
output current.
Ready “1” indicates that the drive is powered, Enabled and no Start Inhibits exist. The state of the assigned
digital output matches the state of bit 2 “Ready” of Par 381 [Drive Status 1].
Ramp Pos “1” indicates that the actual speed of the drive is going positive. Follows the state of Par 346 [Torque
Positive]. Not asserted until after the amount of time in Par 20 [Ramp Delay] has elapsed.
Ramp Neg “1” indicates that the actual speed of the drive is going negative. Follows the state of Par 347 [Torque
Negative]. Not asserted until after the amount of time in Par 20 [Ramp Delay] has elapsed.
Spd Limited “1” indicates that the speed is being limited to the value of Par 3 [Max Speed Fwd], “0” indicates that
the speed is not being limited.
Fault “0” indicates that a drive fault has occurred. Refer to Par 57 [Fault Code].
Power Loss “0” indicates that the drive has detected a loss of the internal power supply.
UserDefinedA Indicates the status of Par 519 [UsrDefBitWrdA] (digital output 1 uses bit 0, digital output 2 uses bit 1,
etc.). Par 1392 [Relay Out 1 Sel] uses bit 14 (only). Par 629 [Relay Out 2 Sel] uses bit 15 (only).
UserDefinedB Indicates the status of Par 536 [UsrDefBitWrdB] (digital output 1 uses bit 0, digital output 2 uses bit 1,
etc.). Par 1392 [Relay Out 1 Sel] uses bit 14 (only). Par 629 [Relay Out 2 Sel] uses bit 15 (only).
INPUT / OUTPUT
Digital Outputs
Stop Control Energized (“1”) at run and de-energized (“0”) based on the value of Par 627 [Spd 0 Trip Delay].
Field Loss “0” indicates the loss of the field voltage/current while the drive is running.
Spd Fbk Loss “0” indicates the loss of Speed Feedback/Encoder due to an excessive calculated error, as
determined by the drive firmware.
Encoder Err “0” indicates a loss of the DC tachometer or encoder. Matches the state of Par 651 [Encoder State].
Diam Calc Energized (“1”) when Par 800 [Diameter Calc St] = 1 and de-energized (“0”) when [Diameter Calc St]
= 0.
Input1 Cmp “1” indicates that the value of analog input 1 is inside the comparison window,“0” indicates that the
value of analog input 1 is outside the comparison window (Par 1045 [Anlg In1 Cmp Eq]).
Diam Reached Energized (“1”) when the value of Par 1158 [Diam Threshold] has been exceeded.
Speed Match Energized (“1”) when the value of Par 1203 [Spd Match Compl] = “1” (launching ramp completed).
Accelerating “1” indicates that the drive is actively accelerating. The state of the assigned digital output matches
the state of bit 4 “Accelerating” of Par 381 [Drive Status 1] and the state of Par 1188 [Accel Status].
Decelerating When set to “1” the drive is actively decelerating. The state of the assigned digital output matches the
state of bit 5 “Decelerating” of Par 381 [Drive Status 1] and the state of Par 1189 [Decel Status].
Brake Cmd Energized (“1”) at run (opens the brake) after the value in Par 1263 [Opening Delay] has been
exceeded. De-energized (“0”) at stop (closes the brake) after the drive speed goes below the value of
Par 1262 [Closing Speed].
ContactorDB “1” issues the close command to the main contactor and dynamic brake contactor.
Contactor “1” issues the close command to the main contactor.
Alarm “0” indicates that a drive alarm has occurred. Refer to Par 1380 [Drive Alarm 1].
Running “1” indicates that the drive is active in Run mode. The state of the assigned digital output matches the
state of bit 2 “Running” of Par 381 [Drive Status 1].
Jogging “1” indicates that the drive is active in Jog mode. The state of the assigned digital output matches the
state of bit 3 “Jogging” of Par 381 [Drive Status 1].
Active “1” indicates that the drive is active in Run or Jog mode. The state of the assigned digital output
matches the state of bit 1 “Active” of Par 381 [Drive Status 1].

Related
Group
File
No.
581 [Dig Out Status] Read Only
Status of the standard digital outputs and relay outputs on the drive and on the
optional I/O Expansion circuit board (if present).
Digital Out8
Digital Out7
Digital Out6
Digital Out5
Digital Out4
Digital Out3
Digital Out2
Digital Out1
Relay Out2
Relay Out1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Default 0 0 x x x x x x 0 0 0 0 0 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
629 [Relay Out 2 Sel] Default: 5= “Ready”

Selects the source of the value that drives the N.O. relay
between the terminals 75 and 76.
Refer to “Option Definitions” on page 3-69.
Options:
0= “Not Used” 8= “Spd Limited” 16 = “Encoder Err” 24 = “ContactDB”

1= “Spd Zero Thr” 9= “Fault” 17 = “Diam Calc” 25 = “Contactor”
INPUT / OUTPUT
Digital Outputs
1267 [Inversion Out 1] Default: 0= “Disabled”

1268 [Inversion Out 2]
1269 [Inversion Out 3] Options: 0= “Disabled”
1270 [Inversion Out 4] 1= “Enabled”
Reverses the digital output signal.
A
1275 [Inversion Relay2] Default: 0= “Disabled”
Inverts the signal for Relay Output 2. Options: 0= “Disabled”
1= “Enabled”
A
1392 [Relay Out 1 Sel] Default: 25 = “Contactor”
Selects the source of the value that drives the N.O. relay
between the terminals 35 and 36.
Refer to “Option Definitions” on page 3-69.
Options:
0= “Not Used” 8= “Spd Limited” 16 = “Encoder Err” 24 = “ContactDB”

1= “Spd Zero Thr” 9= “Fault” 17 = “Diam Calc” 25 = “Contactor”

Related
Digital Outputs Group
File
No.
1393 [Inversion Relay1] Default: 0= “Disabled”
Inverts the signal for Relay Output 1. Options: 0= “Disabled”
1= “Enabled”
A
1323 [DPI P1 Select] Default: 0= “Off”
Selects the destination of the reference value from DPI Port 1. Options: 0= ”Off”
1= “Speed Ref A”
2= “Speed Ref B”
3= “Trim Ramp”
INPUT / OUTPUT
4= “Trim Speed”
5= “Torque Ref”
6= “Trim Torque”
7= “Pos Cur Lim”
8= “Neg Cur Lim”
DPI Inputs
1324 [DPI P2 Select] Refer to Par 1323 [DPI P1 Select].

Selects the destination of the reference value from DPI Port 2.

Parameter Cross Reference Name No. Group Page

Name No. Group Page Anlg3 Tune Scale 83 Analog Inputs 3-62
– by Name AC Line Freq 588 Drive Data 3-13 Arm Current 200 Current Meters 3-12
AC Line Voltage 466 Drive Data 3-13 Arm Current Pct 199 Current Meters 3-12
Acc Dec Filter 1212 Ramp Rates 3-30 Arm Inductance 454 Autotune 3-20
Accel Mask 596 Masks & Owners 3-58 Arm Resistance 453 Autotune 3-20
Accel Owner 605 Masks & Owners 3-59 Arm Volt Ki 494 Speed Regulator 3-27
Accel Status 1188 Diagnostics 3-50 Arm Volt Ki Base 496 Speed Regulator 3-27
Accel Time 1 660 Ramp Rates 3-30 Arm Volt Kp 493 Speed Regulator 3-27
Accel Time 2 24 Ramp Rates 3-29 Arm Volt Kp Base 495 Speed Regulator 3-27
Act Spd Filter 923 Speed Feedback 3-20 At Speed 394 Diagnostics 3-49
Act Ten Ref Pct 1194 Winder Functions 3-43 At Speed Delay 105 Speed Regulator 3-25
Actual Comp 1213 Winder Functions 3-44 At Speed Error 104 Speed Regulator 3-25
Actual Speed 924 Speed Meters 3-12 At Zero Speed 395 Diagnostics 3-49
Actuator Delay 1266 Stop Modes 3-32 Autotune Cur Lim 1048 Auto Tune 3-21
Adaptive I Gain1 189 Adaptv Regulator 3-33 Aux Inp Flt Cfg 354 Alarms 3-53
Adaptive I Gain2 191 Adaptv Regulator 3-33 Base Omega 1163 Diameter Calc 3-41
Adaptive I Gain3 193 Adaptv Regulator 3-33 Clear Fault Que 263 Faults 3-52
Adaptive Joint 1 186 Adaptv Regulator 3-33 Close Loop Comp 1208 Winder Functions 3-44
Adaptive Joint 2 187 Adaptv Regulator 3-33 Closed Loop En 1214 Winder Functions 3-44
Adaptive P Gain1 188 Adaptv Regulator 3-33 Closing Speed 1262 Stop Modes 3-32
Adaptive P Gain2 190 Adaptv Regulator 3-33 Constant J Comp 1172 Winder Functions 3-42
Adaptive P Gain3 192 Adaptv Regulator 3-33 ContactorControl 1391 Digital Inputs 3-67
Adaptive Ref 183 Adaptv Regulator 3-32 Cur Lim Neg Out 11 Current Meters 3-12
Adaptive Reg Typ 182 Adaptv Regulator 3-32 Cur Lim Pos Out 10 Current Meters 3-12
Adaptive Spd 1 184 Adaptv Regulator 3-32 Current Lim Neg 9 Torque Attribute 3-17
Adaptive Spd 2 185 Adaptv Regulator 3-32 Current Lim Pos 8 Torque Attribute 3-17
Adaptive Spd En 181 Adaptv Regulator 3-32 Current Limit 7 Torque Attribute 3-16
Analog In1 Value 1404 Analog Inputs 3-64 Current Reg In 41 Current Meters 3-12
Analog In2 Value 1405 Analog Inputs 3-64 CurrLimit Active 349 Diagnostics 3-47
Analog In3 Value 1406 Analog Inputs 3-64 CurrReg Autotune 452 Autotune 3-20
Anlg In 1 Filter 792 Analog Inputs 3-63 Dancer Constant 798 Diameter Calc 3-40
Anlg In1 Cmp 1042 Analog Inputs 3-63 Data In A1 610 Datalinks 3-60
Anlg In1 Cmp Dly 1044 Analog Inputs 3-63 Data In A2 611 Datalinks 3-60
Anlg In1 Cmp Eq 1045 Analog Inputs 3-63 Data In B1 612 Datalinks 3-60
Anlg In1 Cmp Err 1043 Analog Inputs 3-63 Data In B2 613 Datalinks 3-60
Anlg In1 Config 71 Analog Inputs 3-62 Data In C1 614 Datalinks 3-60
Anlg In1 Offset 74 Analog Inputs 3-63 Data In C2 615 Datalinks 3-60
Anlg In1 Scale 72 Analog Inputs 3-62 Data In D1 616 Datalinks 3-60
Anlg In1 Sel 70 Analog Inputs 3-62 Data In D2 617 Datalinks 3-60
Anlg In1 Target 295 Analog Inputs 3-63 Data In SelData 1320 Datalinks 3-60
Anlg In1 Tune 259 Analog Inputs 3-63 Data In Val Sel 1319 Datalinks 3-60
Anlg In2 Config 76 Analog Inputs 3-62 Data Out A1 618 Datalinks 3-60
Anlg In2 Offset 79 Analog Inputs 3-63 Data Out A2 619 Datalinks 3-60
Anlg In2 Scale 77 Analog Inputs 3-62 Data Out B1 620 Datalinks 3-60
Anlg In2 Sel 75 Analog Inputs 3-62 Data Out B2 621 Datalinks 3-60
Anlg In2 Target 296 Analog Inputs 3-63 Data Out C1 622 Datalinks 3-60
Anlg In2 Tune 260 Analog Inputs 3-63 Data Out C2 623 Datalinks 3-60
Anlg In3 Config 81 Analog Inputs 3-62 Data Out D1 624 Datalinks 3-60
Anlg In3 Offset 84 Analog Inputs 3-63 Data Out D2 625 Datalinks 3-60
Anlg In3 Scale 82 Analog Inputs 3-62 Decel Mask 631 Masks & Owners 3-59
Anlg In3 Sel 80 Analog Inputs 3-62 Decel Owner 609 Masks & Owners 3-59
Anlg In3 Target 297 Analog Inputs 3-63 Decel Status 1189 Diagnostics 3-50
Anlg In3 Tune 261 Analog Inputs 3-63 Decel Time 1 662 Ramp Rates 3-30
Anlg Out1 Scale 62 Analog Outputs 3-64 Decel Time 2 32 Ramp Rates 3-30
Anlg Out1 Sel 66 Analog Outputs 3-64 Diam Calc Dis 1161 Diameter Calc 3-41
Anlg Out2 Scale 63 Analog Outputs 3-64 Diam Inc Dec En 1205 Diameter Calc 3-42
Anlg Out2 Sel 67 Analog Outputs 3-64 Diam init filter 1206 Diameter Calc 3-42
Anlg Out3 Scale 64 Analog Outputs 3-64 Diam Preset 0 1164 Diameter Calc 3-41
Anlg Out3 Sel 68 Analog Outputs 3-64 Diam Preset 1 1165 Diameter Calc 3-41
Anlg Out4 Scale 65 Analog Outputs 3-64 Diam Preset 2 1166 Diameter Calc 3-42
Anlg Out4 Sel 69 Analog Outputs 3-64 Diam Preset 3 1167 Diameter Calc 3-42
Anlg Tach Gain 562 Speed Feedback 3-19 Diam Preset Sel 1168 Diameter Calc 3-42
Anlg Tach Zero 563 Speed Feedback 3-19 Diam stdy delay 1207 Diameter Calc 3-42
Anlg1 Tune Scale 73 Analog Inputs 3-62 Diam Threshold 1158 Diameter Calc 3-41
Anlg2 Tune Scale 78 Analog Inputs 3-62 Diameter Calc 794 Diameter Calc 3-40

Name No. Group Page Name No. Group Page

Diameter Calc St 800 Diameter Calc 3-40 Enable PD 770 PD Control 3-36
Diameter Filter 1162 Diameter Calc 3-41 Enable PI 769 PI Control 3-34
Diameter Reached 1159 Diameter Calc 3-41 Enable PID 1258 PID Control 3-39
Diameter Reset 1157 Diameter Calc 3-41 Encoder Err Chk 652 Speed Feedback 3-20
Dig In Status 564 Digital Inputs 3-67 Encoder Out Sel 1021 Speed Feedback 3-20
Dig In Term 1 565 Digital Inputs 3-67 Encoder PPR 169 Speed Feedback 3-19
Dig In Term 10 574 Digital Inputs 3-67 Encoder Speed 420 Speed Meters 3-11
Dig In Term 11 575 Digital Inputs 3-67 Encoder State 651 Diagnostics 3-50
Dig In Term 12 576 Digital Inputs 3-67 Fast Stop Status 1190 Diagnostics 3-50
Dig In Term 2 566 Digital Inputs 3-67 Fast Stop Time 38 Stop Modes 3-31
Dig In Term 3 567 Digital Inputs 3-67 Fault 1 Code 1351 Faults 3-53
Dig In Term 4 568 Digital Inputs 3-67 Fault 1 Time 1361 Faults 3-53
Dig Out Status 581 Digital Outputs 3-70 Fault 3 Time 1363 Faults 3-53
Digital In1 Sel 133 Digital Inputs 3-65 Fault 4 Code 1354 Faults 3-53
Digital In10 Sel 142 Digital Inputs 3-65 Fault 4 Time 1364 Faults 3-53
Digital Out1 Sel 145 Digital Outputs 3-68 Fault Arm Amps 1371 Faults 3-53
Digital Out2 Sel 146 Digital Outputs 3-68 Fault Clear 1347 Faults 3-52
Digital Out3 Sel 147 Digital Outputs 3-68 Fault Clr Mask 597 Masks & Owners 3-58
Digital Out4 Sel 148 Digital Outputs 3-68 Fault Clr Mode 1348 Faults 3-52
Digital Out5 Sel 149 Digital Outputs 3-68 Fault Clr Owner 606 Masks & Owners 3-59
Digital Out6 Sel 150 Digital Outputs 3-68 Fault Field Amps 1373 Diagnostics 3-53
Digital Out7 Sel 151 Digital Outputs 3-68 Fault Speed 1372 Diagnostics 3-53
Digital Out8 Sel 152 Digital Outputs 3-68 Fault Voltage 1374 Diagnostics 3-53
Direction Mask 594 Masks & Owners 3-58 FaultCode 57 Drive Data 3-13
Direction Mode 1322 Reference Config 3-46 Fdbk Device Type 414 Speed Feedback 3-19
Direction Owner 603 Masks & Owners 3-59 Feed Fwd PID 758 PID Control 3-37
DncrPosSpd 795 Diameter Calc 3-40 Field Current 351 Current Meters 3-12
DPI Baud Rate 589 Comm Control 3-58 Field Econ Delay 1407 Field Config 3-16
DPI Fdbk Select 1321 Comm Control 3-58 Field Economy En 499 Field Config 3-16
DPI P1 Select 1323 DPI Inputs 3-71 Field Mode Sel 469 Field Config 3-15
DPI P2 Select 1324 DPI Inputs 3-71 Field Ref Pct 500 Current Meters 3-12
DPI P3 Select 1325 DPI Inputs 3-71 Field Reg Enable 497 Field Config 3-15
DPI P4 Select 1326 DPI Inputs 3-71 Filt Torq Cur 926 Torque Attribute 3-19
DPI P5 Select 1327 DPI Inputs 3-71 Filt TorqCur Pct 928 Current Meters 3-12
DPI Port Sel 590 Comm Control 3-58 Final Diameter 1178 Winder Functions 3-43
DPI Port Value 1343 Comm Control 3-58 Fld Const 40 Pct 916 Field Config 3-16
Drive Alarm 1 1380 Alarms 3-54 Fld Const 70 Pct 917 Field Config 3-16
Drive Logic Rslt 1328 Diagnostics 3-51 Fld Const 90 Pct 918 Field Config 3-16
Drive Size 465 Drive Data 3-13 Fld Current Pct 234 Torque Attribute 3-12
Drive Status 1 381 Diagnostics 3-48 Fld Reg Ki 92 Field Config 3-14
Drive Status 2 382 Diagnostics 3-48 Fld Reg Ki Base 98 Field Config 3-15
Drive Type 300 Drive Data 3-13 Fld Reg Kp 91 Field Config 3-14
Drive Type Sel 201 Motor Data 3-14 Fld Reg Kp Base 97 Field Config 3-14
Droop Filter 697 Load Limits 3-31 Fld Weaken Ratio 456 Field Config 3-15
Droop Limit 700 Load Limits 3-31 FldLoss Flt Cfg 473 Alarms 3-54
Droop Percent 696 Load Limits 3-31 Flying Start En 388 Speed Regulator 3-27
Drv Fld Brdg Cur 374 Motor Data 3-14 Force Min Field 498 Field Config 3-15
Dynamic Friction 1175 Winder Functions 3-42 Freeze Ramp 373 Ramp Rates 3-30
Elapsed Lifetime 235 Drive Data 3-13 Friction 1015 Autotune 3-21
Enable Droop 699 Load Limits 3-31 Gear Box Ratio 797 Diameter Calc 3-40


I Reg Error 587 Autotune 3-20 Minimum Speed 1 Limits 3-23
Inertia 1014 Autotune 3-21 MOP Accel Time 22 Ramp Rates 3-29
Inertia C Filter 1012 Autotune 3-20 MOP Dec Active 397 Diagnostics 3-49
InertiaCompAct 1191 Speed Regulator 3-28 MOP Decel Time 30 Ramp Rates 3-29
InertiaCompVar 1192 Speed Regulator 3-28 MOP Inc Active 396 Diagnostics 3-49
Initial Diameter 1177 Winder Functions 3-43 MOP Mask 598 Masks & Owners 3-58
Int Acc Calc En 1183 Winder Functions 3-43 MOP Owner 607 Masks & Owners 3-59
Inversion In 1 1276 Digital Inputs 3-67 MOP Select 1375 Reference Config 3-46
Inversion In 10 1388 Digital Inputs 3-67 Nom Mtr Arm Amps 179 Motor Data 3-14
Inversion In 11 1389 Digital Inputs 3-67 Nom Mtr Fld Amps 280 Motor Data 3-14
Inversion In 12 1390 Digital Inputs 3-67 Offs Accel Time 1198 Winder Functions 3-44
Inversion In 2 1277 Digital Inputs 3-67 Opening Delay 1263 Stop Modes 3-32
Inversion In 3 1278 Digital Inputs 3-67 Out Volt Level 921 Field Config 3-16
Inversion In 4 1279 Digital Inputs 3-67 Output Power 1052 Drive Data 3-13
Inversion In 5 1280 Digital Inputs 3-67 Output Voltage 233 Drive Data 3-13
Inversion In 6 1281 Digital Inputs 3-67 OverCurrent Thr 584 Alarms 3-54
Inversion In 7 1282 Digital Inputs 3-67 OverTemp Flt Cfg 365 Alarms 3-53
Inversion In 8 1283 Digital Inputs 3-67 OverVolt Flt Cfg 203 Alarms 3-53
Inversion In 9 1387 Digital Inputs 3-67 Param Access Lvl 211 Drive Memory 3-46
Inversion Out 1 1267 Digital Outputs 3-70 PD Deriv Filter 767 PD Control 3-36
Inversion Out 2 1268 Digital Outputs 3-70 PD Deriv Gain 1 766 PD Control 3-36
Inversion Out 5 1271 Digital Outputs 3-70 PD Output PID 421 PD Control 3-36
Inversion Out 6 1272 Digital Outputs 3-70 PD Prop Gain 1 768 PD Control 3-36
Inversion Relay1 1393 Digital Outputs 3-71 PI Central v sel 779 PI Control 3-35
Inversion Relay2 1275 Digital Outputs 3-70 PI Central v1 776 PI Control 3-34
Jog Mask 593 Masks & Owners 3-58 PI Central v2 777 PI Control 3-34
Jog Owner 602 Masks & Owners 3-59 PI Central v3 778 PI Control 3-34
Jog Off Delay 1409 Discrete Speeds 3-24 PI Central vs0 780 PI Control 3-35
Jog Ramp Time 1410 Ramp Rates 3-29 PI Central vs1 781 PI Control 3-35
Jog Speed 266 Discrete Speeds 3-23 PI Init Intgl Gn 734 PID Control 3-36
Jog TW Enable 1256 Winder Functions 3-45 PI Init Prop Gn 793 PI Control 3-35
Jog TW Speed 1255 Winder Functions 3-45 PI integr freeze 783 PI Control 3-35
Last Stop Source 1402 Diagnostics 3-52 PI Integral Gain 764 PI Control 3-34
Line Accel Pct 1184 Winder Functions 3-43 PI Lower Limit 785 PI Control 3-35
Line Decel Pct 1185 Winder Functions 3-43 PI Output 771 PI Control 3-34
Line FastStp Pct 1186 Winder Functions 3-43 PI Prop Gain PID 765 PI Control 3-34
Line Spd Gain 1156 Diameter Calc 3-41 PI Steady Thr 695 PI Control 3-34
Line Spd Source 1204 Winder Functions 3-44 PI Upper Limit 784 PI Control 3-35
Line Spd Thresh 1155 Diameter Calc 3-41 PID Accel Time 1046 PID Control 3-38
Line Speed Pct 1160 Diameter Calc 3-41 PID Clamp 757 PID Control 3-37
Load Comp 698 Load Limits 3-31 PID Decel Time 1047 PID Control 3-38
Local Mask 599 Masks & Owners 3-59 PID Error 759 PID Control 3-37
Local Owner 608 Masks & Owners 3-59 PID Error Gain 1254 PID Control 3-39
Lock Speed Integ 348 Speed Regulator 3-26 PID Feedback 763 PID Control 3-37
Logic Mask 591 Masks & Owners 3-58 PID Output 774 PID Control 3-37
Security 3-60 PID Output Scale 773 PID Control 3-37
Logic Mask Act 1376 Security 3-60 PID Output Sign 772 PID Control 3-37
Man Ref Preload 210 HIM Ref Config 3-46 PID Setpoint 0 760 PID Control 3-37
Materl Width Pct 1173 Winder Functions 3-42 PID Setpoint 1 761 PID Control 3-37
Max Deviation 796 Diameter Calc 3-40 PID Setpoint Sel 762 PID Control 3-37
Max Diameter 1153 Diameter Calc 3-41 PID Source 786 PID Control 3-38
Max Feedback Spd 162 Motor Data 3-14 PID Source Gain 787 PID Control 3-38
Max Fld Curr Pct 467 Field Config 3-15 PID Steady Delay 731 PID Control 3-36
Max Ref Speed 45 Motor Data 3-14 PID Target 782 PID Control 3-38
Max Speed Fwd 3 Limits 3-23 Port Mask Act 1379 Security 3-61
Max Speed Rev 4 Limits 3-23 Powerup Delay 1345 Restart Modes 3-32
Maximum Speed 2 Limits 3-23 Preset Speed 1 154 Discrete Speeds 3-23
Min Fld Curr Pct 468 Field Config 3-15 Preset Speed 2 155 Discrete Speeds 3-23
Min Speed Fwd 5 Limits 3-23 Preset Speed 3 156 Discrete Speeds 3-23
Min Speed Rev 6 Limits 3-23 Preset Speed 4 157 Discrete Speeds 3-23
Minimum Diameter 799 Diameter Calc 3-40 Preset Speed 5 158 Discrete Speeds 3-23


Preset Speed 6 159 Discrete Speeds 3-23 Scale4 Out Off 1234 Scale Blocks 3-40
Preset Speed 7 160 Discrete Speeds 3-23 Scale4 Output 1228 Scale Blocks 3-39
Ramp Delay 20 Ramp Rates 3-29 Scale5 Div 1239 Scale Blocks 3-39
Ramp In 110 Speed Meters 3-11 Scale5 In Abs 1244 Scale Blocks 3-40
Ramp In Pct 111 Speed Meters 3-11 Scale5 In Max 1240 Scale Blocks 3-39
Ramp In Zero En 1265 Stop Modes 3-32 Scale5 In Min 1241 Scale Blocks 3-39
Ramp Out 113 Speed Meters 3-11 Scale5 In Off 1242 Scale Blocks 3-40
Ramp Out Pct 114 Speed Meters 3-11 Scale5 Input 1237 Scale Blocks 3-39
Ramp Select 0 403 Diagnostics 3-50 Scale5 Mul 1238 Scale Blocks 3-39
Ramp Select 1 404 Diagnostics 3-50 Scale5 Out Off 1243 Scale Blocks 3-40
Ramp Type Select 18 Ramp Rates 3-29 Scale5 Output 1236 Scale Blocks 3-39
Rated Motor Volt 175 Motor Data 3-14 Scale6 Div 1248 Scale Blocks 3-39
Real FF PID 418 PID Control 3-36 Scale6 In Abs 1253 Scale Blocks 3-40
Ref Line Speed 1286 Winder Functions 3-45 Scale6 In Max 1249 Scale Blocks 3-39
Ref Spd Source 1284 Winder Functions 3-45 Scale6 In Min 1250 Scale Blocks 3-39
Ref Speed Gain 1285 Winder Functions 3-45 Scale6 In Off 1251 Scale Blocks 3-40
Ref Zero Level 106 Speed Regulator 3-25 Scale6 Input 1246 Scale Blocks 3-39
Reference Mask 595 Masks & Owners 3-58 Scale6 Mul 1247 Scale Blocks 3-39
Reference Owner 604 Masks & Owners 3-59 Scale6 Out Off 1252 Scale Blocks 3-40
Relay Out 1 Sel 1392 Digital Outputs 3-70 Scale6 Output 1245 Scale Blocks 3-39
Relay Out 2 Sel 629 Digital Outputs 3-70 Set Fld Curve 919 Field Config 3-16
Reset Defaults 258 Drive Memory 3-46 Software Version 331 Configuration 3-13
Reset Fld Curve 920 Field Config 3-16 Spd 0 Trip Delay 627 Stop Modes 3-31
Roll Diameter 1154 Diameter Calc 3-41 Spd Draw Out Pct 1019 Speed Meters 3-12
S Curve Accel 1 665 Ramp Rates 3-30 Spd Fdbk Control 457 Speed Feedback 3-19
S Curve Accel 2 667 Ramp Rates 3-30 Spd Fdbk Error 455 Speed Feedback 3-19
S Curve Decel 1 666 Ramp Rates 3-30 Spd Fdbk Filter 444 Speed Regulator 3-27
S Curve Decel 2 668 Ramp Rates 3-30 Spd Feedback 122 Speed Meters 3-11
S Curve Time 19 Ramp Rates 3-29 Spd Feedback Pct 121 Speed Meters 3-11
Save HIM Ref 209 HIM Ref Config 3-46 Spd Limit Active 372 Diagnostics 3-47
Save MOP Ref 249 Reference Config 3-46 Spd Loss Flt Cfg 478 Alarms 3-54
Scale1 Div 487 Scale Blocks 3-39 Spd Match Acc 1196 Winder Functions 3-44
Scale1 In Abs 492 Scale Blocks 3-40 Spd Match Compl 1203 Winder Functions 3-44
Scale1 In Max 488 Scale Blocks 3-39 Spd Match Dec 1197 Winder Functions 3-44
Scale1 In Min 489 Scale Blocks 3-39 Spd Match Gain 1200 Winder Functions 3-44
Scale1 In Off 490 Scale Blocks 3-40 Spd match torque 1216 Winder Functions 3-45
Scale1 Input 484 Scale Blocks 3-39 Spd Ref Out Pct 384 Speed Meters 3-11
Scale1 Mul 486 Scale Blocks 3-39 Spd Ref Zero En 124 Speed Regulator 3-26
Scale1 Out Off 491 Scale Blocks 3-40 Spd Reg Autotune 1027 Autotune 3-21
Scale1 Output 485 Scale Blocks 3-39 Spd Reg Ki 88 Speed Regulator 3-24
Scale2 Div 556 Scale Blocks 3-39 Spd Reg Ki Base 94 Speed Regulator 3-24
Scale2 In Abs 561 Scale Blocks 3-40 Spd Reg Ki Outpt 100 Speed Regulator 3-24
Scale2 In Max 557 Scale Blocks 3-39 Spd Reg Kp 87 Speed Regulator 3-24
Scale2 In Min 558 Scale Blocks 3-39 Spd Reg Kp Base 93 Speed Regulator 3-24
Scale2 In Off 559 Scale Blocks 3-40 Spd Reg Kp Outpt 99 Speed Regulator 3-24
Scale2 Input 553 Scale Blocks 3-39 Spd Reg Out Pct 236 Speed Regulator 3-11
Scale2 Mul 555 Scale Blocks 3-39 Spd Select 0 400 Diagnostics 3-49
Scale2 Out Off 560 Scale Blocks 3-40 Spd Select 1 401 Diagnostics 3-50
Scale2 Output 554 Scale Blocks 3-39 Spd Select 2 402 Diagnostics 3-50
Scale3 Div 1221 Scale Blocks 3-39 Spd Tune Inertia 1030 Autotune 3-21
Scale3 In Abs 1226 Scale Blocks 3-40 Spd Up Gain Pct 445 Speed Regulator 3-27
Scale3 In Max 1222 Scale Blocks 3-39 Spd Zero I En 123 Speed Regulator 3-26
Scale3 In Min 1223 Scale Blocks 3-39 Spd Zero P En 125 Speed Regulator 3-26
Scale3 In Off 1224 Scale Blocks 3-40 SpdFuncSelect 1016 Speed Regulator 3-28
Scale3 Input 1218 Scale Blocks 3-39 SpdReg FB Bypass 458 Speed Feedback 3-19
Scale3 Mul 1220 Scale Blocks 3-39 SpdReg Ki Bypass 460 Speed Regulator 3-27
Scale3 Out Off 1225 Scale Blocks 3-40 SpdReg Kp Bypass 459 Speed Regulator 3-27
Scale3 Output 1219 Scale Blocks 3-39 SpdTune Friction 1031 Autotune 3-21
Scale4 Div 1230 Scale Blocks 3-39 Speed Demand En 1215 Winder Functions 3-45
Scale4 In Abs 1235 Scale Blocks 3-40 Speed Draw Out 1018 Speed Meters 3-12
Scale4 In Max 1231 Scale Blocks 3-39 Speed Match 1195 Winder Functions 3-43
Scale4 In Min 1232 Scale Blocks 3-39 Speed Ramp En 245 Ramp Rates 3-30
Scale4 In Off 1233 Scale Blocks 3-40 Speed Ratio 1017 Speed References 3-24
Scale4 Input 1227 Scale Blocks 3-39 Speed Ref A 44 Speed Meters 3-11
Scale4 Mul 1229 Scale Blocks 3-39 Speed Ref A Pct 47 Speed Meters 3-11


Speed Ref B 48 Speed Meters 3-11 UnderVolt Thresh 481 Alarms 3-54
Speed Ref B Pct 49 Speed Meters 3-11 UserDefined0 503 User Defined 3-55
Speed Ref Out 385 Speed Meters 3-11 UserDefined1 504 User Defined 3-55
Speed Reg En 242 Speed Regulator 3-26 UserDefined10 513 User Defined 3-55
Speed Reg In 118 Speed Meters 3-11 UserDefined11 514 User Defined 3-55
Speed Reg In Pct 117 Speed Meters 3-11 UserDefined12 515 User Defined 3-55
Speed Thresh Neg 102 Speed Regulator 3-25 UserDefined13 516 User Defined 3-55
Speed Thresh Pos 101 Speed Regulator 3-25 UserDefined14 517 User Defined 3-55
Speed Threshold 393 Diagnostics 3-49 UserDefined15 518 User Defined 3-55
Speed Tune Dir 1029 Autotune 3-21 UserDefined2 505 User Defined 3-55
Speed Tune Ki 1033 Autotune 3-21 UserDefined3 506 User Defined 3-55
Speed Tune Kp 1032 Autotune 3-21 UserDefined4 507 User Defined 3-55
Speed Up Base 446 Speed Regulator 3-27 UserDefined5 508 User Defined 3-55
Speed Up Filter 447 Speed Regulator 3-27 UserDefined6 509 User Defined 3-55
Speed Zero Delay 108 Speed Regulator 3-25 UserDefined7 510 User Defined 3-55
Speed Zero Level 107 Speed Regulator 3-25 UserDefined8 511 User Defined 3-55
Spd Zero P Gain 126 Speed Regulator 3-26 UserDefined9 512 User Defined 3-55
Start At Powerup 1344 Restart Modes 3-32 UsrDefBitWrdA 519 User Defined 3-55
Start Inhibits 1403 Diagnostics 3-52 UsrDefBitWrdA0 520 User Defined 3-56
Start Mask 592 Masks & Owners 3-58 UsrDefBitWrdA1 521 User Defined 3-56
Start Owner 601 Masks & Owners 3-59 UsrDefBitWrdA10 530 User Defined 3-56
Static F Zero 1287 Winder Functions 3-45 UsrDefBitWrdA11 531 User Defined 3-56
Static Friction 1174 Winder Functions 3-42 UsrDefBitWrdA12 532 User Defined 3-56
Status1 at Fault 1349 Faults 3-52 UsrDefBitWrdA13 533 User Defined 3-56
Status2 at Fault 1350 Faults 3-52 UsrDefBitWrdA14 534 User Defined 3-56
Stop Owner 600 Masks & Owners 3-59 UsrDefBitWrdA15 535 User Defined 3-56
Tachometer Speed 1408 Speed Meters 3-12 UsrDefBitWrdA2 522 User Defined 3-56
Taper Enable 1176 Winder Functions 3-43 UsrDefBitWrdA3 523 User Defined 3-56
TaskLoad 1 ms 1384 Diagnostics 3-51 UsrDefBitWrdA4 524 User Defined 3-56
TB Manual Ref 267 Discrete Speeds 3-24 UsrDefBitWrdA8 528 User Defined 3-56
Tension Reduct 1179 Winder Functions 3-43 UsrDefBitWrdA9 529 User Defined 3-56
Tension Ref 1180 Winder Functions 3-43 UsrDefBitWrdB 536 User Defined 3-57
Tension Scale 1181 Winder Functions 3-43 UsrDefBitWrdB0 537 User Defined 3-57
TestPoint Data 1382 Diagnostics 3-51 UsrDefBitWrdB1 538 User Defined 3-57
TestPoint Sel 1381 Diagnostics 3-51 UsrDefBitWrdB10 547 User Defined 3-57
Threshold Delay 103 Speed Regulator 3-25 UsrDefBitWrdB11 548 User Defined 3-57
Time AccDec Min 1182 Winder Functions 3-43 UsrDefBitWrdB12 549 User Defined 3-57
Torq Current Pct 1193 Winder Functions 3-43 UsrDefBitWrdB13 550 User Defined 3-57
Torq Limit Type 715 Load Limits 3-31 UsrDefBitWrdB14 551 User Defined 3-57
Torq Red CurLim 13 Load Limits 3-31 UsrDefBitWrdB15 552 User Defined 3-57
Torque Const 1013 Autotune 3-20 UsrDefBitWrdB2 539 User Defined 3-57
Torque Negative 347 Diagnostics 3-47 UsrDefBitWrdB3 540 User Defined 3-57
Torque Positive 346 Diagnostics 3-47 UsrDefBitWrdB4 541 User Defined 3-57
Torque Reduction 342 Torque Attribute 3-17 UsrDefBitWrdB5 542 User Defined 3-57
Torque Ref 39 Torque Attribute 3-17 UsrDefBitWrdB6 543 User Defined 3-57
Torque Winder En 1209 Winder Functions 3-44 UsrDefBitWrdB7 544 User Defined 3-57
Trim Ramp 42 Speed Reference 3-24 UsrDefBitWrdB8 545 User Defined 3-57
Trim Ramp Pct 378 Speed Reference 3-24 UsrDefBitWrdB9 546 User Defined 3-57
Trim Speed 43 Speed Reference 3-24 UsrDsplyDiv0 51 User Defined 3-54
Trim Speed Pct 379 Speed Reference 3-24 UsrDsplyMult0 50 User Defined 3-54
Trim Torque 40 Torque Attribute 3-17 UsrValDiv1 54 User Defined 3-55
TrqTpr_Enable 750 Torque Attribute 3-18 UsrValMult1 53 User Defined 3-54
TrqTpr_Lim0 751 Torque Attribute 3-18 Variable J Comp 1171 Winder Functions 3-42
TrqTpr_Lim1 752 Torque Attribute 3-18 W Gain 1202 Winder Functions 3-44
TrqTpr_Lim2 753 Torque Attribute 3-18 W Offset 1199 Winder Functions 3-44
TrqTpr_Lim3 754 Torque Attribute 3-18 W Reference 1217 Winder Functions 3-45
TrqTpr_Lim4 755 Torque Attribute 3-18 W Target 1210 Winder Functions 3-44
TrqTpr_Spd 756 Torque Attribute 3-18 Winder Side 1201 Winder Functions 3-44
TstGen Amplitude 60 Test Generator 3-22 Winder Type 1187 Winder Functions 3-43
TstGen Frequency 59 Test Generator 3-22 Write Mask Act 1377 Security 3-61
TstGen Offset 61 Test Generator 3-22 Write Mask Cfg 1378 Security 3-61
TstGen Output 58 Test Generator 3-22 Z Channel Enable 911 Speed Feedback 3-20

Name No. Group Page

Z Captured Pos 913 Speed Feedback 3-20
Z Capture Pos En 912 Speed Feedback 3-20
Zero Ramp Input 345 Ramp Rates 3-30
Zero Ramp Output 344 Ramp Rates 3-30
Zero Torque 353 Torque Attribute 3-17
Parameter Cross Reference No. Parameter Name Group Page

No. Parameter Name Group Page 78 Anlg2 Tune Scale Analog Inputs 3-62
– by Number 1 Minimum Speed Limits 3-23 79 Anlg In2 Offset Analog Inputs 3-63
2 Maximum Speed Limits 3-23 80 Anlg In3 Sel Analog Inputs 3-62
3 Max Speed Fwd Limits 3-23 81 Anlg In3 Config Analog Inputs 3-62
4 Max Speed Rev Limits 3-23 82 Anlg In3 Scale Analog Inputs 3-62
5 Min Speed Fwd Limits 3-23 83 Anlg3 Tune Scale Analog Inputs 3-62
6 Min Speed Rev Limits 3-23 84 Anlg In3 Offset Analog Inputs 3-63
7 Current Limit Torque Attribute 3-16 87 Spd Reg Kp Speed Regulator 3-24
8 Current Lim Pos Torque Attribute 3-17 88 Spd Reg Ki Speed Regulator 3-24
9 Current Lim Neg Torque Attribute 3-17 91 Fld Reg Kp Field Config 3-14
10 Cur Lim Pos Out Current Meters 3-12 92 Fld Reg Ki Field Config 3-14
11 Cur Lim Neg Out Current Meters 3-12 93 Spd Reg Kp Base Speed Regulator 3-24
13 Torq Red CurLim Load Limits 3-31 94 Spd Reg Ki Base Speed Regulator 3-24
18 Ramp Type Select Ramp Rates 3-29 97 Fld Reg Kp Base Field Config 3-14
19 S Curve Time Ramp Rates 3-29 98 Fld Reg Ki Base Field Config 3-15
20 Ramp Delay Ramp Rates 3-29 99 Spd Reg Kp Outpt Speed Regulator 3-24
22 MOP Accel Time Ramp Rates 3-29 100 Spd Reg Ki Outpt Speed Regulator 3-24
24 Accel Time 2 Ramp Rates 3-29 101 Speed Thresh Pos Speed Regulator 3-25
30 MOP Decel Time Ramp Rates 3-29 102 Speed Thresh Neg Speed Regulator 3-25
32 Decel Time 2 Ramp Rates 3-30 103 Threshold Delay Speed Regulator 3-25
38 Fast Stop Time Stop Modes 3-31 104 At Speed Error Speed Regulator 3-25
39 Torque Ref Torque Attribute 3-17 105 At Speed Delay Speed Regulator 3-25
40 Trim Torque Torque Attribute 3-17 106 Ref Zero Level Speed Regulator 3-25
41 Current Reg In Current Meters 3-12 107 Speed Zero Level Speed Regulator 3-25
42 Trim Ramp Speed Reference 3-24 108 Speed Zero Delay Speed Regulator 3-25
43 Trim Speed Speed Reference 3-24 110 Ramp In Speed Meters 3-11
44 Speed Ref A Speed Meters 3-11 111 Ramp In Pct Speed Meters 3-11
45 Max Ref Speed Motor Data 3-14 113 Ramp Out Speed Meters 3-11
47 Speed Ref A Pct Speed Meters 3-11 114 Ramp Out Pct Speed Meters 3-11
48 Speed Ref B Speed Meters 3-11 117 Speed Reg In Pct Speed Meters 3-11
49 Speed Ref B Pct Speed Meters 3-11 118 Speed Reg In Speed Meters 3-11
50 UsrDsplyMult0 User Defined 3-54 121 Spd Feedback Pct Speed Meters 3-11
51 UsrDsplyDiv0 User Defined 3-54 122 Spd Feedback Speed Meters 3-11
53 UsrValMult1 User Defined 3-54 123 Spd Zero I En Speed Regulator 3-26
54 UsrValDiv1 User Defined 3-55 124 Spd Ref Zero En Speed Regulator 3-26
57 FaultCode Drive Data 3-13 125 Spd Zero P En Speed Regulator 3-26
58 TstGen Output Test Generator 3-22 126 Spd Zero P Gain Speed Regulator 3-26
59 TstGen Frequency Test Generator 3-22 133 Digital In1 Sel Digital Inputs 3-65
60 TstGen Amplitude Test Generator 3-22 134 Digital In2 Sel Digital Inputs 3-65
61 TstGen Offset Test Generator 3-22 135 Digital In3 Sel Digital Inputs 3-65
62 Anlg Out1 Scale Analog Outputs 3-64 136 Digital In4 Sel Digital Inputs 3-65
66 Anlg Out1 Sel Analog Outputs 3-64 140 Digital In8 Sel Digital Inputs 3-65
70 Anlg In1 Sel Analog Inputs 3-62 144 Digital In12 Sel Digital Inputs 3-65
71 Anlg In1 Config Analog Inputs 3-62 145 Digital Out1 Sel Digital Outputs 3-68
72 Anlg In1 Scale Analog Inputs 3-62 146 Digital Out2 Sel Digital Outputs 3-68
73 Anlg1 Tune Scale Analog Inputs 3-62 147 Digital Out3 Sel Digital Outputs 3-68
74 Anlg In1 Offset Analog Inputs 3-63 148 Digital Out4 Sel Digital Outputs 3-68
75 Anlg In2 Sel Analog Inputs 3-62 149 Digital Out5 Sel Digital Outputs 3-68
76 Anlg In2 Config Analog Inputs 3-62 150 Digital Out6 Sel Digital Outputs 3-68
77 Anlg In2 Scale Analog Inputs 3-62 151 Digital Out7 Sel Digital Outputs 3-68

No. Parameter Name Group Page No. Parameter Name Group Page
152 Digital Out8 Sel Digital Outputs 3-68 374 Drv Fld Brdg Cur Motor Data 3-14
154 Preset Speed 1 Discrete Speeds 3-23 378 Trim Ramp Pct Speed Reference 3-24
155 Preset Speed 2 Discrete Speeds 3-23 379 Trim Speed Pct Speed Reference 3-24
156 Preset Speed 3 Discrete Speeds 3-23 381 Drive Status 1 Diagnostics 3-48
157 Preset Speed 4 Discrete Speeds 3-23 382 Drive Status 2 Diagnostics 3-48
158 Preset Speed 5 Discrete Speeds 3-23 384 Spd Ref Out Pct Speed Meters 3-11
159 Preset Speed 6 Discrete Speeds 3-23 385 Speed Ref Out Speed Meters 3-11
160 Preset Speed 7 Discrete Speeds 3-23 388 Flying Start En Speed Regulator 3-27
162 Max Feedback Spd Motor Data 3-14 393 Speed Threshold Diagnostics 3-49
169 Encoder PPR Speed Feedback 3-19 394 At Speed Diagnostics 3-49
175 Rated Motor Volt Motor Data 3-14 395 At Zero Speed Diagnostics 3-49
179 Nom Mtr Arm Amps Motor Data 3-14 396 MOP Inc Active Diagnostics 3-49
181 Adaptive Spd En Adaptv Regulator 3-32 397 MOP Dec Active Diagnostics 3-49
182 Adaptive Reg Typ Adaptv Regulator 3-32 400 Spd Select 0 Diagnostics 3-49
183 Adaptive Ref Adaptv Regulator 3-32 401 Spd Select 1 Diagnostics 3-50
184 Adaptive Spd 1 Adaptv Regulator 3-32 402 Spd Select 2 Diagnostics 3-50
185 Adaptive Spd 2 Adaptv Regulator 3-32 403 Ramp Select 0 Diagnostics 3-50
186 Adaptive Joint 1 Adaptv Regulator 3-33 404 Ramp Select 1 Diagnostics 3-50
187 Adaptive Joint 2 Adaptv Regulator 3-33 414 Fdbk Device Type Speed Feedback 3-19
188 Adaptive P Gain1 Adaptv Regulator 3-33 418 Real FF PID PID Control 3-36
189 Adaptive I Gain1 Adaptv Regulator 3-33 420 Encoder Speed Speed Meters 3-11
190 Adaptive P Gain2 Adaptv Regulator 3-33 421 PD Output PID PD Control 3-36
191 Adaptive I Gain2 Adaptv Regulator 3-33 444 Spd Fdbk Filter Speed Regulator 3-27
192 Adaptive P Gain3 Adaptv Regulator 3-33 445 Spd Up Gain Pct Speed Regulator 3-27
193 Adaptive I Gain3 Adaptv Regulator 3-33 446 Speed Up Base Speed Regulator 3-27
199 Arm Current Pct Current Meters 3-12 447 Speed Up Filter Speed Regulator 3-27
200 Arm Current Current Meters 3-12 452 CurrReg Autotune Autotune 3-20
201 Drive Type Sel Motor Data 3-14 453 Arm Resistance Autotune 3-20
203 OverVolt Flt Cfg Alarms 3-53 454 Arm Inductance Autotune 3-20
209 Save HIM Ref HIM Ref Config 3-46 455 Spd Fdbk Error Speed Feedback 3-19
210 Man Ref Preload HIM Ref Config 3-46 456 Fld Weaken Ratio Field Config 3-15
211 Param Access Lvl Drive Memory 3-46 457 Spd Fdbk Control Speed Feedback 3-19
233 Output Voltage Drive Data 3-13 458 SpdReg FB Bypass Speed Feedback 3-19
234 Fld Current Pct Torque Attribute 3-12 459 SpdReg Kp Bypass Speed Regulator 3-27
235 Elapsed Lifetime Drive Data 3-13 460 SpdReg Ki Bypass Speed Regulator 3-27
236 Spd Reg Out Pct Speed Regulator 3-11 465 Drive Size Drive Data 3-13
242 Speed Reg En Speed Regulator 3-26 466 AC Line Voltage Drive Data 3-13
245 Speed Ramp En Ramp Rates 3-30 467 Max Fld Curr Pct Field Config 3-15
249 Save MOP Ref Reference Config 3-46 468 Min Fld Curr Pct Field Config 3-15
258 Reset Defaults Drive Memory 3-46 469 Field Mode Sel Field Config 3-15
259 Anlg In1 Tune Analog Inputs 3-63 473 FldLoss Flt Cfg Alarms 3-54
260 Anlg In2 Tune Analog Inputs 3-63 478 Spd Loss Flt Cfg Alarms 3-54
261 Anlg In3 Tune Analog Inputs 3-63 481 UnderVolt Thresh Alarms 3-54
263 Clear Fault Que Faults 3-52 484 Scale1 Input Scale Blocks 3-39
266 Jog Speed Discrete Speeds 3-23 485 Scale1 Output Scale Blocks 3-39
267 TB Manual Ref Discrete Speeds 3-24 486 Scale1 Mul Scale Blocks 3-39
280 Nom Mtr Fld Amps Motor Data 3-14 487 Scale1 Div Scale Blocks 3-39
295 Anlg In1 Target Analog Inputs 3-63 488 Scale1 In Max Scale Blocks 3-39
296 Anlg In2 Target Analog Inputs 3-63 489 Scale1 In Min Scale Blocks 3-39
297 Anlg In3 Target Analog Inputs 3-63 490 Scale1 In Off Scale Blocks 3-40
300 Drive Type Drive Data 3-13 491 Scale1 Out Off Scale Blocks 3-40
331 Software Version Configuration 3-13 492 Scale1 In Abs Scale Blocks 3-40
342 Torque Reduction Torque Attribute 3-17 493 Arm Volt Kp Speed Regulator 3-27
344 Zero Ramp Output Ramp Rates 3-30 494 Arm Volt Ki Speed Regulator 3-27
345 Zero Ramp Input Ramp Rates 3-30 495 Arm Volt Kp Base Speed Regulator 3-27
346 Torque Positive Diagnostics 3-47 496 Arm Volt Ki Base Speed Regulator 3-27
347 Torque Negative Diagnostics 3-47 497 Field Reg Enable Field Config 3-15
348 Lock Speed Integ Speed Regulator 3-26 498 Force Min Field Field Config 3-15
349 CurrLimit Active Diagnostics 3-47 499 Field Economy En Field Config 3-16
351 Field Current Current Meters 3-12 500 Field Ref Pct Current Meters 3-12
353 Zero Torque Torque Attribute 3-17 503 UserDefined0 User Defined 3-55
354 Aux Inp Flt Cfg Alarms 3-53 504 UserDefined1 User Defined 3-55
365 OverTemp Flt Cfg Alarms 3-53 505 UserDefined2 User Defined 3-55
372 Spd Limit Active Diagnostics 3-47 506 UserDefined3 User Defined 3-55
373 Freeze Ramp Ramp Rates 3-30 507 UserDefined4 User Defined 3-55

508 UserDefined5 User Defined 3-55 573 Dig In Term 9 Digital Inputs 3-67
512 UserDefined9 User Defined 3-55 581 Dig Out Status Digital Outputs 3-70
513 UserDefined10 User Defined 3-55 584 OverCurrent Thr Alarms 3-54
514 UserDefined11 User Defined 3-55 587 I Reg Error Autotune 3-20
515 UserDefined12 User Defined 3-55 588 AC Line Freq Drive Data 3-13
516 UserDefined13 User Defined 3-55 589 DPI Baud Rate Comm Control 3-58
517 UserDefined14 User Defined 3-55 590 DPI Port Sel Comm Control 3-58
518 UserDefined15 User Defined 3-55 591 Logic Mask Masks & Owners 3-58
Security 3-60
519 UsrDefBitWrdA User Defined 3-55
592 Start Mask Masks & Owners 3-58
520 UsrDefBitWrdA0 User Defined 3-56
593 Jog Mask Masks & Owners 3-58
594 Direction Mask Masks & Owners 3-58
595 Reference Mask Masks & Owners 3-58
596 Accel Mask Masks & Owners 3-58
597 Fault Clr Mask Masks & Owners 3-58
598 MOP Mask Masks & Owners 3-58
599 Local Mask Masks & Owners 3-59
600 Stop Owner Masks & Owners 3-59
601 Start Owner Masks & Owners 3-59
602 Jog Owner Masks & Owners 3-59
603 Direction Owner Masks & Owners 3-59
604 Reference Owner Masks & Owners 3-59
605 Accel Owner Masks & Owners 3-59
606 Fault Clr Owner Masks & Owners 3-59
607 MOP Owner Masks & Owners 3-59
608 Local Owner Masks & Owners 3-59
536 UsrDefBitWrdB User Defined 3-57
609 Decel Owner Masks & Owners 3-59
537 UsrDefBitWrdB0 User Defined 3-57
610 Data In A1 Datalinks 3-60
611 Data In A2 Datalinks 3-60
612 Data In B1 Datalinks 3-60
613 Data In B2 Datalinks 3-60
614 Data In C1 Datalinks 3-60
615 Data In C2 Datalinks 3-60
616 Data In D1 Datalinks 3-60
617 Data In D2 Datalinks 3-60
618 Data Out A1 Datalinks 3-60
619 Data Out A2 Datalinks 3-60
620 Data Out B1 Datalinks 3-60
621 Data Out B2 Datalinks 3-60
622 Data Out C1 Datalinks 3-60
623 Data Out C2 Datalinks 3-60
624 Data Out D1 Datalinks 3-60
553 Scale2 Input Scale Blocks 3-39 625 Data Out D2 Datalinks 3-60
627 Spd 0 Trip Delay Stop Modes 3-31
554 Scale2 Output Scale Blocks 3-39
629 Relay Out 2 Sel Digital Outputs 3-70
555 Scale2 Mul Scale Blocks 3-39
631 Decel Mask Masks & Owners 3-59
556 Scale2 Div Scale Blocks 3-39
651 Encoder State Diagnostics 3-50
557 Scale2 In Max Scale Blocks 3-39
652 Encoder Err Chk Speed Feedback 3-20
558 Scale2 In Min Scale Blocks 3-39
660 Accel Time 1 Ramp Rates 3-30
559 Scale2 In Off Scale Blocks 3-40
662 Decel Time 1 Ramp Rates 3-30
560 Scale2 Out Off Scale Blocks 3-40
665 S Curve Accel 1 Ramp Rates 3-30
561 Scale2 In Abs Scale Blocks 3-40
666 S Curve Decel 1 Ramp Rates 3-30
562 Anlg Tach Gain Speed Feedback 3-19
667 S Curve Accel 2 Ramp Rates 3-30
563 Anlg Tach Zero Speed Feedback 3-19
668 S Curve Decel 2 Ramp Rates 3-30
564 Dig In Status Digital Inputs 3-67
695 PI Steady Thr PI Control 3-34
565 Dig In Term 1 Digital Inputs 3-67
696 Droop Percent Load Limits 3-31
697 Droop Filter Load Limits 3-31
698 Load Comp Load Limits 3-31
699 Enable Droop Load Limits 3-31
700 Droop Limit Load Limits 3-31
715 Torq Limit Type Load Limits 3-31
731 PID Steady Delay PID Control 3-36

734 PI Init Intgl Gn PID Control 3-36 1013 Torque Const Autotune 3-20
750 TrqTpr_Enable Torque Attribute 3-18 1014 Inertia Autotune 3-21
751 TrqTpr_Lim0 Torque Attribute 3-18 1015 Friction Autotune 3-21
752 TrqTpr_Lim1 Torque Attribute 3-18 1016 SpdFuncSelect Speed Regulator 3-28
753 TrqTpr_Lim2 Torque Attribute 3-18 1017 Speed Ratio Speed References 3-24
754 TrqTpr_Lim3 Torque Attribute 3-18 1018 Speed Draw Out Speed Meters 3-12
755 TrqTpr_Lim4 Torque Attribute 3-18 1019 Spd Draw Out Pct Speed Meters 3-12
756 TrqTpr_Spd Torque Attribute 3-18 1021 Encoder Out Sel Speed Feedback 3-20
757 PID Clamp PID Control 3-37 1027 Spd Reg Autotune Autotune 3-21
758 Feed Fwd PID PID Control 3-37 1029 Speed Tune Dir Autotune 3-21
759 PID Error PID Control 3-37 1030 Spd Tune Inertia Autotune 3-21
760 PID Setpoint 0 PID Control 3-37 1031 SpdTune Friction Autotune 3-21
761 PID Setpoint 1 PID Control 3-37 1032 Speed Tune Kp Autotune 3-21
762 PID Setpoint Sel PID Control 3-37 1033 Speed Tune Ki Autotune 3-21
763 PID Feedback PID Control 3-37 1042 Anlg In1 Cmp Analog Inputs 3-63
764 PI Integral Gain PI Control 3-34 1043 Anlg In1 Cmp Err Analog Inputs 3-63
765 PI Prop Gain PID PI Control 3-34 1044 Anlg In1 Cmp Dly Analog Inputs 3-63
766 PD Deriv Gain 1 PD Control 3-36 1045 Anlg In1 Cmp Eq Analog Inputs 3-63
767 PD Deriv Filter PD Control 3-36 1046 PID Accel Time PID Control 3-38
768 PD Prop Gain 1 PD Control 3-36 1047 PID Decel Time PID Control 3-38
769 Enable PI PI Control 3-34 1048 Autotune Cur Lim Auto Tune 3-21
770 Enable PD PD Control 3-36 1052 Output Power Drive Data 3-13
771 PI Output PI Control 3-34 1153 Max Diameter Diameter Calc 3-41
772 PID Output Sign PID Control 3-37 1154 Roll Diameter Diameter Calc 3-41
773 PID Output Scale PID Control 3-37 1155 Line Spd Thresh Diameter Calc 3-41
774 PID Output PID Control 3-37 1156 Line Spd Gain Diameter Calc 3-41
776 PI Central v1 PI Control 3-34 1157 Diameter Reset Diameter Calc 3-41
777 PI Central v2 PI Control 3-34 1158 Diam Threshold Diameter Calc 3-41
778 PI Central v3 PI Control 3-34 1159 Diameter Reached Diameter Calc 3-41
779 PI Central v sel PI Control 3-35 1160 Line Speed Pct Diameter Calc 3-41
780 PI Central vs0 PI Control 3-35 1161 Diam Calc Dis Diameter Calc 3-41
781 PI Central vs1 PI Control 3-35 1162 Diameter Filter Diameter Calc 3-41
782 PID Target PID Control 3-38 1163 Base Omega Diameter Calc 3-41
783 PI integr freeze PI Control 3-35 1164 Diam Preset 0 Diameter Calc 3-41
784 PI Upper Limit PI Control 3-35 1165 Diam Preset 1 Diameter Calc 3-41
785 PI Lower Limit PI Control 3-35 1166 Diam Preset 2 Diameter Calc 3-42
786 PID Source PID Control 3-38 1167 Diam Preset 3 Diameter Calc 3-42
787 PID Source Gain PID Control 3-38 1168 Diam Preset Sel Diameter Calc 3-42
788 PD Prop Gain 2 PD Control 3-36 1171 Variable J Comp Winder Functions 3-42
789 PD Deriv Gain 2 PD Control 3-36 1172 Constant J Comp Winder Functions 3-42
790 PD Prop Gain 3 PD Control 3-36 1173 Materl Width Pct Winder Functions 3-42
791 PD Deriv Gain 3 PD Control 3-36 1174 Static Friction Winder Functions 3-42
792 Anlg In 1 Filter Analog Inputs 3-63 1175 Dynamic Friction Winder Functions 3-42
793 PI Init Prop Gn PI Control 3-35 1176 Taper Enable Winder Functions 3-43
794 Diameter Calc Diameter Calc 3-40 1177 Initial Diameter Winder Functions 3-43
795 DncrPosSpd Diameter Calc 3-40 1178 Final Diameter Winder Functions 3-43
796 Max Deviation Diameter Calc 3-40 1179 Tension Reduct Winder Functions 3-43
797 Gear Box Ratio Diameter Calc 3-40 1180 Tension Ref Winder Functions 3-43
798 Dancer Constant Diameter Calc 3-40 1181 Tension Scale Winder Functions 3-43
799 Minimum Diameter Diameter Calc 3-40 1182 Time AccDec Min Winder Functions 3-43
800 Diameter Calc St Diameter Calc 3-40 1183 Int Acc Calc En Winder Functions 3-43
911 Z Channel Enable Speed Feedback 3-20 1184 Line Accel Pct Winder Functions 3-43
912 Z Capture Pos En Speed Feedback 3-20 1185 Line Decel Pct Winder Functions 3-43
913 Z Captured Pos Speed Feedback 3-20 1186 Line FastStp Pct Winder Functions 3-43
916 Fld Const 40 Pct Field Config 3-16 1187 Winder Type Winder Functions 3-43
917 Fld Const 70 Pct Field Config 3-16 1188 Accel Status Diagnostics 3-50
918 Fld Const 90 Pct Field Config 3-16 1189 Decel Status Diagnostics 3-50
919 Set Fld Curve Field Config 3-16 1190 Fast Stop Status Diagnostics 3-50
920 Reset Fld Curve Field Config 3-16 1191 InertiaCompAct Speed Regulator 3-28
921 Out Volt Level Field Config 3-16 1192 InertiaCompVar Speed Regulator 3-28
923 Act Spd Filter Speed Feedback 3-20 1193 Torq Current Pct Winder Functions 3-43
924 Actual Speed Speed Meters 3-12 1194 Act Ten Ref Pct Winder Functions 3-43
926 Filt Torq Cur Torque Attribute 3-19 1195 Speed Match Winder Functions 3-43
928 Filt TorqCur Pct Current Meters 3-12 1196 Spd Match Acc Winder Functions 3-44
1012 Inertia C Filter Autotune 3-20 1197 Spd Match Dec Winder Functions 3-44

1198 Offs Accel Time Winder Functions 3-44 1269 Inversion Out 3 Digital Outputs 3-70
1199 W Offset Winder Functions 3-44 1270 Inversion Out 4 Digital Outputs 3-70
1200 Spd Match Gain Winder Functions 3-44 1271 Inversion Out 5 Digital Outputs 3-70
1201 Winder Side Winder Functions 3-44 1272 Inversion Out 6 Digital Outputs 3-70
1202 W Gain Winder Functions 3-44 1273 Inversion Out 7 Digital Outputs 3-70
1203 Spd Match Compl Winder Functions 3-44 1274 Inversion Out 8 Digital Outputs 3-70
1204 Line Spd Source Winder Functions 3-44 1275 Inversion Relay2 Digital Outputs 3-70
1205 Diam Inc Dec En Diameter Calc 3-42 1276 Inversion In 1 Digital Inputs 3-67
1206 Diam init filter Diameter Calc 3-42 1277 Inversion In 2 Digital Inputs 3-67
1207 Diam stdy delay Diameter Calc 3-42 1278 Inversion In 3 Digital Inputs 3-67
1208 Close Loop Comp Winder Functions 3-44 1279 Inversion In 4 Digital Inputs 3-67
1209 Torque Winder En Winder Functions 3-44 1280 Inversion In 5 Digital Inputs 3-67
1210 W Target Winder Functions 3-44 1281 Inversion In 6 Digital Inputs 3-67
1212 Acc Dec Filter Ramp Rates 3-30 1282 Inversion In 7 Digital Inputs 3-67
1213 Actual Comp Winder Functions 3-44 1283 Inversion In 8 Digital Inputs 3-67
1214 Closed Loop En Winder Functions 3-44 1284 Ref Spd Source Winder Functions 3-45
1215 Speed Demand En Winder Functions 3-45 1285 Ref Speed Gain Winder Functions 3-45
1216 Spd match torque Winder Functions 3-45 1286 Ref Line Speed Winder Functions 3-45
1217 W Reference Winder Functions 3-45 1287 Static F Zero Winder Functions 3-45
1218 Scale3 Input Scale Blocks 3-39 1319 Data In Val Sel Datalinks 3-60
1219 Scale3 Output Scale Blocks 3-39 1320 Data In SelData Datalinks 3-60
1220 Scale3 Mul Scale Blocks 3-39 1321 DPI Fdbk Select Comm Control 3-58
1221 Scale3 Div Scale Blocks 3-39 1322 Direction Mode Reference Config 3-46
1222 Scale3 In Max Scale Blocks 3-39 1323 DPI P1 Select DPI Inputs 3-71
1223 Scale3 In Min Scale Blocks 3-39 1324 DPI P2 Select DPI Inputs 3-71
1224 Scale3 In Off Scale Blocks 3-40 1325 DPI P3 Select DPI Inputs 3-71
1225 Scale3 Out Off Scale Blocks 3-40 1326 DPI P4 Select DPI Inputs 3-71
1226 Scale3 In Abs Scale Blocks 3-40 1327 DPI P5 Select DPI Inputs 3-71
1227 Scale4 Input Scale Blocks 3-39 1328 Drive Logic Rslt Diagnostics 3-51
1228 Scale4 Output Scale Blocks 3-39 1343 DPI Port Value Comm Control 3-58
1229 Scale4 Mul Scale Blocks 3-39 1344 Start At Powerup Restart Modes 3-32
1230 Scale4 Div Scale Blocks 3-39 1345 Powerup Delay Restart Modes 3-32
1231 Scale4 In Max Scale Blocks 3-39 1347 Fault Clear Faults 3-52
1232 Scale4 In Min Scale Blocks 3-39 1348 Fault Clr Mode Faults 3-52
1233 Scale4 In Off Scale Blocks 3-40 1349 Status1 at Fault Faults 3-52
1234 Scale4 Out Off Scale Blocks 3-40 1350 Status2 at Fault Faults 3-52
1235 Scale4 In Abs Scale Blocks 3-40 1351 Fault 1 Code Faults 3-53
1236 Scale5 Output Scale Blocks 3-39 1352 Fault 2 Code Faults 3-53
1237 Scale5 Input Scale Blocks 3-39 1353 Fault 3 Code Faults 3-53
1238 Scale5 Mul Scale Blocks 3-39 1354 Fault 4 Code Faults 3-53
1239 Scale5 Div Scale Blocks 3-39 1355 Fault 5 Code Faults 3-53
1240 Scale5 In Max Scale Blocks 3-39 1356 Fault 6 Code Faults 3-53
1241 Scale5 In Min Scale Blocks 3-39 1357 Fault 7 Code Faults 3-53
1242 Scale5 In Off Scale Blocks 3-40 1358 Fault 8 Code Faults 3-53
1243 Scale5 Out Off Scale Blocks 3-40 1359 Fault 9 Code Faults 3-53
1244 Scale5 In Abs Scale Blocks 3-40 1360 Fault 10 Code Faults 3-53
1245 Scale6 Output Scale Blocks 3-39 1361 Fault 1 Time Faults 3-53
1246 Scale6 Input Scale Blocks 3-39 1362 Fault 2 Time Faults 3-53
1247 Scale6 Mul Scale Blocks 3-39 1363 Fault 3 Time Faults 3-53
1248 Scale6 Div Scale Blocks 3-39 1364 Fault 4 Time Faults 3-53
1249 Scale6 In Max Scale Blocks 3-39 1365 Fault 5 Time Faults 3-53
1250 Scale6 In Min Scale Blocks 3-39 1366 Fault 6 Time Faults 3-53
1251 Scale6 In Off Scale Blocks 3-40 1367 Fault 7 Time Faults 3-53
1252 Scale6 Out Off Scale Blocks 3-40 1368 Fault 8 Time Faults 3-53
1253 Scale6 In Abs Scale Blocks 3-40 1369 Fault 9 Time Faults 3-53
1254 PID Error Gain PID Control 3-39 1370 Fault 10 Time Faults 3-53
1255 Jog TW Speed Winder Functions 3-45 1371 Fault Arm Amps Faults 3-53
1256 Jog TW Enable Winder Functions 3-45 1372 Fault Speed Diagnostics 3-53
1258 Enable PID PID Control 3-39 1373 Fault Field Amps Diagnostics 3-53
1262 Closing Speed Stop Modes 3-32 1374 Fault Voltage Diagnostics 3-53
1263 Opening Delay Stop Modes 3-32 1375 MOP Select Reference Config 3-46
1265 Ramp In Zero En Stop Modes 3-32 1376 Logic Mask Act Security 3-60
1266 Actuator Delay Stop Modes 3-32 1377 Write Mask Act Security 3-61
1267 Inversion Out 1 Digital Outputs 3-70 1378 Write Mask Cfg Security 3-61
1268 Inversion Out 2 Digital Outputs 3-70 1379 Port Mask Act Security 3-61

No. Parameter Name Group Page

1380 Drive Alarm 1 Alarms 3-54
1381 TestPoint Sel Diagnostics 3-51
1382 TestPoint Data Diagnostics 3-51
1383 TaskLoad 32 ms Diagnostics 3-51
1387 Inversion In 9 Digital Inputs 3-67
1391 ContactorControl Digital Inputs 3-67
1392 Relay Out 1 Sel Digital Outputs 3-70
1393 Inversion Relay1 Digital Outputs 3-71
1402 Last Stop Source Diagnostics 3-52
1403 Start Inhibits Diagnostics 3-52
1404 Analog In1 Value Analog Inputs 3-64
1407 Field Econ Delay Field Config 3-16
1408 Tachometer Speed Speed Meters 3-12
1409 Jog Off Delay Discrete Speeds 3-24
1410 Jog Ramp Time Ramp Rates 3-29

Chapter 4
Troubleshooting
This chapter provides information to guide you in troubleshooting the

PowerFlex DC drive. Included is a listing and description of drive faults
(with possible solutions, when applicable) and alarms.
See
For information on… page…
Faults and Alarms 4-1
Drive Status 4-2
Manually Clearing Faults 4-3
Fault Descriptions 4-4
Clearing Alarms 4-7
Alarm Descriptions 4-7
Common Drive Symptoms and Corrective Actions 4-10
Testpoint Codes and Functions 4-14
Faults and Alarms A fault is a condition that always stops the drive and prevents it from
starting until the fault condition is corrected. There are two fault types.
Type Description
➀ User Configurable This type of fault allows you to configure the drive’s response to the
condition that caused the error.
• When configured for a fault, the drive will be stopped, the error condition will
be annunciated on the HIM or a via digital output (if programmed) and the
drive will not be allowed to start until the fault condition is corrected.
• When configured for an alarm, the error condition will be annunciated on the
HIM or via a digital output (if programmed) and the drive will continue to run
and/or be allowed to start.
• When configured for ignore or disabled, the error condition will not be
recognized by the drive or be indicated on the HIM or via a programmed
digital output.
➁ Non-Configurable This type of fault is always enabled and will cause the drive to stop
running in order to protect the drive and/or motor from damage. In
some cases, drive or motor repair may be required. The cause of the
fault must be corrected before the fault can be cleared (via a fault reset
using the HIM or programmed digital input). The fault will be reset on
power up after repair.
An alarm indicates a drive error condition that does not stop the drive, but
may prevent it from starting. There are two types of alarms.
Type Description
➀ User Configurable This type of alarm indicates a drive error condition but does not stop
the drive from starting or running. However, if this type of alarm is left
uncorrected, a fault condition may eventually occur.
➁ Non-Configurable This type of alarm is always enabled and will prevent the drive from
starting until the alarm condition is corrected.

4-2 Troubleshooting
Drive Status The condition or state of your drive is constantly monitored. Any changes
will be indicated through the LEDs and/or the HIM (if present).
Figure 4.1 Drive Status Indicators
PORT
MOD
NET A
NET B
➋ ➊
STS
# Name Color State Description

➊ STS Green Flashing Drive ready, but not running and no faults are present.
(Status) Steady Drive running, no faults are present.
Yellow Flashing, A condition exists that is preventing the drive from
Drive Stopped starting. Check parameters 1403 [Start Inhibits] and/or
1380 [Drive Alarm 1].
Flashing, An intermittent type 1 alarm condition is occurring.
Drive Running Check parameter 1380 [Drive Alarm 1]. Refer to Fault
page 4-7.
Steady, A continuous type 1 alarm condition exists. Check
Drive Running parameter 1380 [Drive Alarm 1]. Refer to Fault
page 4-7.
Red Flashing A fault has occurred. Check [Fault x Code] or view the
Fault Queue on the HIM. Refer to Fault Descriptions on
page 4-4.
Steady A non-resettable, non-configurable fault has occurred.
Check [Fault x Code] or view the Fault Queue on the
HIM. Refer to Fault Descriptions on page 4-4.
➋ PORT Refer to the Communication Status of DPI port internal communications (if present).
MOD Adapter User Manual. Status of communications module (when installed).
NET A Status of network (if connected).
NET B Status of secondary network (if connected).

Troubleshooting 4-3
HIM Indication
The LCD HIM also provides visual notification of a fault or alarm
condition.
Condition Display
The drive is indicating a fault.
The LCD HIM immediately reports the fault condition by F-> Faulted Auto
displaying the following: 0.0 Hz
• “Faulted” appears in the status line — Fault — F 5
Main
Arm Menu:
• Fault number OverVoltage
Diagnostics
Time Since Fault
• Fault name 0000:23:52
Parameter
• Time that has passed since the fault occurred
Press “Esc” to regain HIM control.
The drive is indicating an alarm.
The LCD HIM immediately reports the alarm condition by F-> DigInCflctA Auto
displaying the following: 0.0 RPM
• Alarm name Main Menu:
• Alarm bell graphic Diagnostics
Parameter
Device Select
Manually Clearing Faults

Step Key(s)
1. Press “Esc” to acknowledge the fault. The fault information will be removed
Esc
so that you can use the HIM.
2. Address the condition that caused the fault.

The cause must be corrected before the fault can be cleared.
3. After corrective action has been taken, clear the fault by one of these
methods.
• Press “Stop”
• Cycle drive power
• Set parameter 1347 [Fault Clear] to 1 “Clear Faults”
• “Clear Faults” on the HIM Diagnostic menu

4-4 Troubleshooting
Fault Descriptions Table 4.A Fault Types, Descriptions and Actions
Fault No. Type(1) Description Action

AC Undervoltage 4 ➀ There is an undervoltage on the power circuit.
Possible causes include:
• Par 481 [UnderVolt Thresh] is set incorrectly Set Par 481 [UnderVolt Thresh] correctly and then
(possibly set to 400V when the drive is rated for reset the drive via Par 1347 [Fault Clear].
230V input power).
• The incoming voltage to the power terminals
(U/V/W) of the drive is too low due to:
• The AC input voltage is too low • Verify AC input power level.
• There are poor cable connections (e.g. • Check all connections.
terminals on contactor, choke, filter, etc., is
not properly connected).
• The incoming voltage to the control power
terminals (U2, V2) is too low due to:
• The AC input voltage is too low • Verify AC input power level.
• There are poor cable connections. • Check all connections.
• The fuse(s) on the Switching Power Supply • Check and replace the fuse(s) if necessary.
circuit board have blown.
• The line fuses have tripped. 1. Remove power from the drive.
• The AC input voltage dips or there is a high 2. Eliminate AC input voltage dips and/or disturbances.
disturbance in the supply voltage. 3. Replace any blown fuses.
Arm Overvoltage 5 ➀ There is an overvoltage on the armature circuit.
• Par 175 [Rated Motor Volt] is set too low. Set Par 175 [Rated Motor Volt] correctly.
• The drive is not configured to use field Check the value of Par 469 [Field Mode Sel] and set
weakening, but the motor can only reach the accordingly.
set speed when the drive is in field weakening
mode.
Note: Configure with Par 203 [OverVolt Flt Cfg].
Auxiliary Input 2 ➀ An auxiliary input interlock is open or a voltage
(+15 - 30 V) or reference signal is missing for the
Check the remote wiring.
digital input set to 14 “Aux Fault”.

Note: Configure with Par 354 [Aux Inp Flt Cfg].
Drive Overload 64 ➁ Drive Rating of 150% for 1 minute or 200% for 3
seconds has been exceeded
Reduce the load or extend the acceleration time.
Dsp Error 132 ➁ A non-resettable software error exists on the

Control board.
Cycle power to the drive. If the problem persists,
replace the Control board.
EEPROM Error 100 ➁ There was a problem saving parameter values or
there has been a control board change.
1. Reset the fault.
2. If this fault occurs again, cycle power to the drive.
Note: When this fault occurs, the parameters will 3. If the problem persists, replace the Control board.
be reset to the default settings.
Encoder Loss 91 ➀ The drive is not receiving a speed feedback
signal. Possible causes include:
• The conductors of the feedback signal have Current from one or more of the feedback device wires
been interrupted. is not reaching the drive. Check the feedback device
wiring.
• One or several encoder channels are missing Check the encoder connections and power supply.
(conductor interruption, no encoder power
supply).
Note: Configure with Par 478 [Spd Loss Flt Cfg].
Fld Current Loss 6 ➀ The field current is too low. Possible causes
include:
• The field current regulator is currently not Enable the field current regulator via Par 497 [Field
enabled. Reg Enable].
• The conductors in the field circuit have been Check the motor field wiring. Measure the resistance of
interrupted. the motor and verify that it matches motor nameplate
data.
• The field fuses are currently open. Check the field fuses and replace as necessary.
Note: Configure with Par 473 [FldLoss Flt Cfg].

Troubleshooting 4-5

Hardware Fault 130 ➁ A non-resettable hardware error has occurred. Cycle power to the drive. If the problem persists,
replace the Control board.
Heatsink OvrTemp 8 ➁ The heatsink temperature is too high
• The surrounding air temperature is too high. Lower the surrounding air temperature.
• The drive’s cooling fans have failed (drives > Check the fan fuses and fans. If the fan fuses have
110 A). failed, replace the fuses. The fans have failed, replace
the fans.
• The heatsink is dirty. Clean the heatsink.
Interrupt Error 131 ➁ A non-resettable software error has occurred in
the main application.
Report this error to the manufacturer.
Inverting Fault 37 ➁ A digital input (Pars 133-144) configured as 64

“Invert Flt” has been asserted.
Check the status of the inverting fault device connected
to the digital input.
Main Contactor 10 ➁ One of the following has occurred: • Check all contactor wiring and drive jumpers. Repair
• The Main and/or Dynamic Brake (DB) or replace the contactor(s) if the problem(s) persist.
contactor failed to open or close in the proper • Check the digital input and/or relay output 1
amount of time. (terminals 35 and 36) wiring and configuration using
• A digital input and/or relay output 1 is Pars 1391 [ContactorControl], 1392 [Relay Out 1
incorrectly wired and/or configured. Sel] and [Digital Inx Sel]. Refer to Using
• Wiring to a digital input configured for contactor Contactors on page 1-9 for more information.
has opened.
Motor Over Temp 16 ➀ The motor has exceeded its temperature rating
(as signaled by the thermistor connected to the
drive terminals 78 and 79). Possible causes
include:
• The motor does not have a thermistor and Refer to Thermistors and Thermal Switches on
there is no resistor between terminals 78 and page 1-25 for configuration information.
79 on the drive.
• The cable between the thermistor connection Check and repair any damage to or loss of connection
on the motor and terminals 78 and 79 on the of the thermistor cables between the motor and drive.
drive has been broken.
• The overheating of the motor may have been
caused by one of the following:
• The Load cycle is too extreme.
• The surrounding air temperature at the site Reduce the load.
of motor is too high.
• The motor has an external fan and the fan
failed. Reduce the surrounding air temperature.
• The motor does not have an external fan and
the load is too large at low speeds. The Replace the motor fan.
cooling effect of the internal fan on the motor
shaft is too low for this load cycle. Reduce the load cycle or fit the motor with an external
fan.
Note: Configure with Par 365 [OverTemp Flt Cfg].
No Fault 0 – There are currently no faults in the drive. Informational only.
Overcurrent 13 ➀ An overcurrent has occurred in the motor circuit.
• There is a short-circuit or ground fault at the Verify the armature circuit wiring is correct.
output of the drive.
• The current regulator was not properly fine Refer to Tune the Current Regulator: on page 2-10.
tuned.
• The value of Par 584 [OverCurrent Thr] is too Increase the value of Par 584 [OverCurrent Thr]
low. accordingly.
Overspeed 25 ➁ The Encoder/Tachometer feedback indicated a
speed that is more than 10% above the value in
Remove the excessive load or overhauling conditions
or increase the value of Par 2 [Maximum Speed].
Par 2 [Maximum Speed].
Params Defaulted 48 ➁ User parameters have been reset to their default
values.
Informational only.
Port 1-5 Adapter 71 - 75 ➁ The communications card has a fault. Check the DPI device event queue and corresponding
fault information for the device.

4-6 Troubleshooting

Port 1-5 DPI Loss 81 - 85 ➁ The DPI port stopped communicating. 1. Check the HIM connection.
2. If adapter was not intentionally disconnected, check
the wiring to the port. Replace the wiring, port
expander, adapters, Control Board or complete drive
as required.
3. If an adapter was intentionally disconnected and the
bit for that adapter in Par 591 [Logic Mask] is set to
“1”, this fault will occur. To disable this fault, set the
appropriate bit in [Logic Mask] for the adapter to “0.”
Power Failure 3 ➁ There is a fault in the 24V Control board supply - • Pull the plug-in I/O terminal blocks out of the control
the voltage is below the permitted value. In most circuit board and reset the drive via 1347 [Fault
cases the cause is in the external I/O wiring. Clear]. If there are no other faults, check the I/O
wiring for a short-circuit including the cable
shielding.
• Check fuses F1 and F2 located on the Switching
Power Supply circuit board (frame A size drives only
have one fuse - F1). Replace as necessary.*
• Check varistor fuses F1, F2, and F3 on the Pulse
Transformer or Transient Noise Filter circuit boards
for Frame C size drives. Replace as necessary.*
• If this fault occurs again, an internal fault may be
present. Contact your Rockwell Automation sales
office.
*Note: Refer to Control Power Circuit Protection
Fuses on page A-15 for fuse sizing information.
ATTENTION: Remove power from the drive before removing

! the I/O terminal blocks and/or fuses.
STune Aborted 62 ➁ The speed regulator auto tuning procedure has

been stopped by the user.
Informational only.
STune CurLimit 59 ➁ The value of Par 1048 [Autotune Cur Lim] for auto
tuning the speed regulator is set too high.
Decrease the value of Par 1048 [Autotune Cur Lim]
and repeat the auto tune procedure.
STune FrictionLo 60 ➁ The friction value attained during the auto tuning
procedure is zero or lower than the control
precision limit.
STune LoadHi 58 ➁ The loading torque value is too high at zero speed
to complete the speed regulator auto tuning
Decrease the load torque, where applicable, and
repeat the auto tune procedure.
procedure.
STune Overspeed 56 ➁ The measured motor speed is too high during the
speed regulator auto tuning procedure.
STune Stalled 57 ➁ The drive stalled during the speed regulator auto
tuning procedure.
Increase the value of Par 1048 [Autotune Cur Lim] and
repeat the auto tune procedure.
STune Timeout 61 ➁ The speed regulator auto tuning procedure did
not complete within the available time.
Verify the value in Par 1048 [Autotune Cur Lim]. If this
value is set to low, the motor will not be able to reach a
maximum speed of 33% of the lower of the values in
Par 45 [Max Ref Speed] or Par 3 [Max Speed Fwd] or
Par 4 [Max Speed Rev] and not be able to complete
the test. Set these values appropriately and repeat the
auto tuning procedure.
Sustained Curr 70 ➁ The motor CEMF is too high or the line voltage is • Check the line voltage and frequency.
too low. • Check the motor brushes and connections.
• Check the Main and DB Contactor connections if
present.
• Verify that there are no overhauling loads present.
(1)
See page 4-1 for a description of fault types.

Troubleshooting 4-7
Table 4.B Fault Cross Reference by Number

No.(1) Fault No. (1) Fault
2 Auxiliary Input 64 Drive Overload
3 Power Failure 70 Sustained Curr
4 AC Undervoltage 71 - Port 1 Adaptor
5 Arm Overvoltage 75 Port 2 Adaptor
6 Fld Current Loss Port 3 Adaptor
8 Heatsink OvrTemp Port 4 Adaptor
10 Main Contactor Port 5 Adaptor
13 Over Current 81 - Port 1 DPI Loss
16 Motor Over Temp 85 Port 2 DPI Loss
25 Overspeed Port 3 DPI Loss
37 Inverting Fault Port 4 DPI Loss
56 STune Overspeed Port 5 DPI Loss
57 STune Stalled 91 Encoder Loss
58 STune LoadHi 100 EEPROM Error
59 STune CurLimit 130 Hardware Fault
60 STune FrictionLo 131 Interrupt Error
61 STune Timeout 132 Dsp Error
62 STune Aborted
(1) Fault numbers not listed are reserved for future use.
Clearing Alarms Alarms are automatically cleared when the condition that caused the alarm
is no longer present.
Alarm Descriptions The status of the alarms can be viewed in 1380 [Drive Alarm 1].
Table 4.C Alarm Descriptions and Actions
Alarm Type Description
AnalogCflct ➁ Sel],
More than one of the drive's reference inputs (Pars 70, 75 and 80 [Anlg Inx
Pars 1323-1327 [DPI Px Select], or Par 1021 [Encoder Out Sel]) are set
to "Speed Ref A" or "Speed Ref B". This alarm takes precedence over the
“EncoderCflct” alarm when both are present. Refer to Figure C.1 or Speed
Reference Selection on page D-5 for a graphical representation of the drive's
reference selections.
Arm
Overvoltage
➀ Motor
There is a possible overvoltage on the armature circuit or Par 175 [Rated
Volt] is set too low for the application. Refer to the “Arm Overvoltage”
fault description on page 4-4 for more information.
Auxiliary Input ➀ An auxiliary input interlock is open or a voltage (+15 - 30 V) or reference
signal is missing for the digital input set to 14 “Aux Fault”. Refer to the
“Auxiliary Input” fault description on page 4-4 for more information.
BipolarCflct ➁ ofParthe1322 [Direction Mode] is set to “Bipolar” or “Reverse Dis” and one or more
following digital input functions is configured: “Fwd/Reverse,” “Run
Forward,” “Run Reverse,” “Jog Forward” or “Jog Reverse.”

4-8 Troubleshooting

CntactrCflct ➁ Contactor input functions are in conflict:
• When Par 1391 [ContactorControl] is set to “None”, both relay outputs
(Pars 1392 [Relay Out 1 Sel] and 629 [Relay Out 2 Sel] and all digital inputs
([Digital Inx Sel]) cannot be set to “Contactor” or “ContactorDB”.
• With [ContactorControl] set to “Contactor”, one relay output and one digital
input must be set to “Contactor”. No output can be defined as
“ContactorDB”.
• With [ContactorControl] set to “Contactor+DB”, both relay outputs and one
digital input must be set to “Contactor”, “ContactorDB” and “Contactor”,
respectively.
Because any relay output can be configured as contactor or DB control and
any digital input as contactor status, care must be taken to correctly wire the
terminal blocks to match the parameter selections.
DigInCflctA ➁ Digital input functions are in conflict. Combinations marked with a “ ” will
cause an alarm.
Acc2/Dec2 Accel 2 Decel 2 Jog 1/2 Jog Fwd Jog Rev Fwd/Rev
Acc2/Dec2
Accel 2
Decel 2
Jog 1/2
Jog Fwd
Jog Rev
Fwd/Rev
DigInCflctB ➁ One of the following digital input conflicts exists:

• A digital Start input has been configured without a Stop input
• None of the digital inputs are configured for “Enable”
• Other digital input functions are in conflict. Combinations that conflict are
marked with a “ ” and will cause an alarm.
Stop- Jog Fwd/

Start CF Run Run Fwd Run Rev 1/2 Jog Fwd Jog Rev Rev
Start
Stop-CF
Run
Run Fwd
Run Rev
Jog 1/2
Jog Fwd
Jog Rev
Fwd/Rev
DigInCflctC ➁ More than one physical input has been configured to the same input function.
Multiple configurations are not allowed for the following input functions.
Forward/Reverse Run Reverse Run Forward
Jog Forward Jog Reverse Speed Select 1
Speed Select 2 Speed Select 3 Acc2 / Dec2
Accel 2 Decel 2 Run
Encoder Loss ➀ The drive is not receiving a speed feedback signal from the encoder. Refer to
the “Encoder Loss” fault description on page 4-4 for more information.
EncoderCflct ➁ One of the following has occurred:
• Par 414 [Fdbk Device Type] is set to 1 “Encoder” and Par 1021 [Encoder
Out Sel] is not set to 0 “Off”. If you are using an encoder, set Par 1021
[Encoder Out Sel] to 0 “Off”.
• More than one of the following parameters contains the same value: Pars
1021 [Encoder Out Sel], 70, 75 and 80 [Anlg Inx Sel], and/or 1323 - 1327
[DPI Px Select].

Troubleshooting 4-9

Fld Current
Loss
➀ The field current is too low. Refer to the “Fld Current Loss” fault description on
page 4-4 for more information.
Motor Over
Temp
➀ The motor has exceeded its temperature rating (as signaled by the thermistor
connected to the drive terminals 78 and 79). Refer to the “Motor Over Temp”
fault description on page 4-5 for more information.
Start At
PowerUp
➀ Par 1344 [Start At Powerup] is enabled. The drive may start at any time after
drive power up and the time specified in Par 1345 [Powerup Delay] has
elapsed.

4-10 Troubleshooting
Common Drive Symptoms Drive will not start

and Corrective Actions Drive Symptom Action
An external “Start” command was issued, but the • Verify that no faults or alarms are displayed. If a
drive does not start. fault or alarm is displayed, follow the corrective
action provided (refer to Fault Descriptions on
page 4-4 or Alarm Descriptions on page 4-7).
• The external wiring to the programmed Start
terminal block connection is missing.
• Verify that +24V DC is present at terminal block
connection.
• Verify that 24V Supply Common is connected
between terminals 18 and 16.
• Verify that the configuration for Pars 133-144
[Digital Inx Sel] matches the switch wiring.
The drive is not in a "Ready" state, is not Check the Enable and Stop inputs. Verify that the
“Enabled” or a “Stop” is asserted. wiring is correct (refer to I/O Wiring Examples on
page 1-37).
External AC Input or DC Output contactor, if used, If using an AC Input contactor:
has not closed. • Verify that the drive is "Ready", then verify that
the required coil voltage is present at terminals
35 and 36 (Relay Output 1). If the coil voltage is
present at terminals 35 or 36, then verify that
proper voltage is at the AC Input contactor coil.
• Inspect the contactor for mechanical problems.
• Verify that Par 1391 [ContactorControl] is set
properly.
• Verify that the contactor and/or auxiliary
contact is properly wired to a digital input on
the drive and that the appropriate digital input
selection parameter (133-144 [Digital Inx Sel])
is set to 31 “Contactor”.
• Verify that parameter 1392 [Relay Out 1 Sel] is
set to 25 “Contactor”.
If using an external DC Output contactor:
• Verify that the drive is "Ready", then verify that
the required coil voltage is present at terminals
the proper voltage is at the DC Output
contactor coil.
• Inspect the contactor for mechanical problems.
• Verify that parameter 1391 [ContactorControl]
is set properly.
• Verify that the contactor and/or auxiliary
contact is properly wired to a digital input on
the drive and that the appropriate digital input
selection parameter (133-144 [Digital Inx Sel])
is set to 31 “Contactor”.
set to 25 “Contactor”.

Troubleshooting 4-11
Drive Symptom Action

The external DB resistor contactor, if used, has • Verify that the drive is "Ready", then verify that
not closed. the required coil voltage is present at terminals
proper voltage is at the DB contactor coil.
• Inspect contactor for mechanical problems.
• Verify that parameter 1391 [ContactorControl]
is set properly.
• Verify that the auxiliary contacts for the AC
Input or DC Output contactor and DB contactor
are properly wired in series to a digital input on
the drive.
• Verify that the appropriate digital input selection
parameter (133-144 [Digital Inx Sel]) is set to
31 “Contactor”.
set to 24 “ContactorDB”.
The drive starts from the HIM but will not start Check masks for Terminal Block control (see
from the terminal block. parameters 591 [Logic Mask] and 592 [Start
Mask]).

Drive starts but motor does not turn and no armature current.
The drive starts but there is no armature current • Verify the wiring to the analog input(s)
and the motor does not respond to a speed signal. selected for speed reference (refer to I/O
Wiring Examples on page 1-37).
• Verify the setting(s) of switch S9 and Par 71
[Anlg In1 Config]; or S10 and Par 76 [Anlg
In2 Config]; or S11 and Par 81 [Anlg In3
Config] (refer to DIP Switch and Jumper
Settings on page 1-32).
• Verify the speed selection digital input(s) and
the respective input terminal voltage(s), if
used.
• Verify the analog input(s) voltage(s)
displayed in parameters 1404 [Analog In1
Value], 1405 [Analog In2 Value] or 1406
[Analog In3 Value].
The drive starts and armature current is present • The Load may be too great for the motor and
but the motor does not turn. drive.
• Remove the load from the motor and test for
motor rotation. If the motor rotates, then
verify that the measured armature current,
using an in-line current meter or DC clamp
on meter, equals the armature current
feedback value displayed in parameters 200
[Arm Current] and 199 [Arm Current Pct].
Increase the value of parameter 7 [Current
Limit], 8 [Current Lim Pos] or 9 [Current Lim
Neg].
• Verify that the measured motor field current,
using an in-line current meter or DC clamp
on meter, equals the feedback value
displayed in parameter 351 [Field Current].
• Verify that the motor nameplate value equals
the value displayed in parameter 280 [Nom
Mtr Field Amps].
• Measure the DC voltage supplied to the
motor field. Verify that the value of
parameter 374 [Drv Fld Brdg Cur] equals the
setting of DIP Switch S14.
• If the motor does not rotate with the load
removed, check the motor.
• Verify that parameter 353 [Zero Torque] is
not enabled.

Troubleshooting 4-13
The motor does not reach commanded speed.

The drive starts and the motor turns but does The load may be too great for the motor and drive.
reach the commanded speed. • Remove the load from the motor and test for
the correct commanded speed. If the motor
reaches the commanded speed, then verify
that the measured armature current, using an
in-line current meter or DC clamp on meter,
equals the armature current feedback value
displayed in parameters 200 [Arm Current] and
199 [Arm Current Pct]. Increase the value of
parameter 7 [Current Limit], 8 [Current Lim Pos]
or 9 [Current Lim Neg].
• Verify that the measured motor field current,
using an in-line current meter or DC clamp on
meter, equals the feedback value displayed in
parameter 351 [Field Current].
If the motor does not achieve commanded speed
continue with following tests:
• Check the speed parameter limits: parameters
2 [Maximum Speed], 3 [Max Speed Fwd], 4
[Max Speed Rev] and 122 [Spd Feedback].
• Check the analog voltage input and speed
reference values: parameters 1404 [Analog In1
Value], 1405 [Analog In2 Value], 44 [Speed Ref
A], 48 [Speed Ref B]
• Check the setting of switch S9 and parameter
71 [Anlg In1 Config], S10 and 76 [Anlg In2
Config] or S11 and 81 [Anlg In3 Config].
• Tune the analog input(s) using parameters
259-261 [Anlg Inx Tune] with the potentiometer
set at max.
• The encoder pulse per revolution (PPR)
parameter (169 [Encoder PPR]) value is too
high.
• The DC Tach Scaling is incorrect or the
jumpers are not properly set. Check parameter
562 [Anlg Tach Gain] and check the setting of
the DC Analog Tachometer DIP Switch S4 (see
Figure 1.30 on page 1-34).
The motor is turning in the wrong direction.

The motor is rotating in the wrong direction. The motor is incorrectly wired.
• Change the armature or field connections to
the drive.
ATTENTION: If the motor is turning the wrong direction and the drive is
using an encoder or DC analog tachometer for feedback and the speed
! feedback is correct, then the feedback wiring must be changed. If using an
encoder, then two encoder connections must be reversed (A with A-Not or B
with B-Not). If using a DC analog tachometer, then the tachometer leads
must be reversed.
• The Polarity of the analog speed reference

signal is incorrect for the required direction.

The motor reaches maximum speed immediately.

The motor accelerates to maximum speed and Check the analog input voltage and speed
cannot be controlled. reference values:
• Parameters 1404 [Analog In1 Value], 1405
[Analog In2 Value], 44 [Speed Ref A] and 48
[Speed Ref B]
• Check the setting of switch S9 and parameter
71 [Anlg In1 Config], S10 and 76 [Anlg In2
Config] or S11 and 81 [Anlg In3 Config].
The feedback device, encoder or DC analog
tachometer is not connected, incorrectly
connected or has failed.
• Change parameter 414 [Fdbk Device Type] to 3
“Armature” to test the encoder or DC analog
tachometer feedback.
Testpoint Codes and Select a testpoint with Par 1381 [TestPoint Sel]. Values can be viewed with
Functions Par 1382 [TestPoint Data].
Values
No. (1) Description Minimum Maximum Default
566 Rx count
567 Tx count
568 BusLoss count
569 Port 1 Timeout
570 Port 2 Timeout 0 65535 0
571 Port 3 Timeout
572 Port 4 Timeout
573 Port 5 Timeout
574 Port 6 Timeout
(1)
Enter in [TestPoint Sel].
Control Board Testpoints:

Test Point Function Test Point Function
XY20 Monitors (± 10VDC) the [Anlg Outx Sel] parameter XY17 Output current signal
values (using this test point, set all of the [Anlg Outx (0.61 V = nominal
Sel] parameters to the variable that must be
measured) drive output current)
XY10 Reference point XY18 Reference point

Appendix A
Supplemental Drive Information
For information on . . See page . .
Specifications A-1
IP20 (NEMA UL/Type Open) Watts Loss A-4
Communication Configurations A-5
Drive Power Circuit Protection A-7
Control Power Circuit Protection Fuses A-15
AC Input Line Reactors and AC Input Contactors A-17
DC Output Contactors and Dynamic Brake Resistor Kits A-19
DC Contactor Crimp Lug Kit Specifications A-21
Specifications
Category Specification
Agency According to file E59272 for the series of the approved devices.
Certification
The drive is also designed to meet the following specifications:
NFPA 70 - US National Electrical Code
Drive Type Full Wave Regen, 6 Pulse, Regulated Field Supply
Protection Heat Sink Thermistor: Monitored by microprocessor overtemp trip
Drive Overcurrent Trip
Software Overcurrent Trip: 200% of rated current (typical)
Hardware Overcurrent Trip: 220-300% of rated current (dependent on drive rating)
Line transients: Up to 2000 volts peak per IEC 6100-4-5
Control Logic Noise Showering arc transients up to 1500V peak
Immunity:
Power Ride-Thru: 15 milliseconds at full load
Logic Control Ride-Thru: 0.5 seconds minimum, 2 seconds typical
Ground Fault Trip: Phase-to-ground on drive output
Short Circuit Trip: Phase-to-phase on drive output
Environment Altitude: 1000 m (3300 ft) max. without derating.
(1)
De-rate output power by 1.2% for every 100 meters
(328ft) above 1000 meters (3300ft).
Maximum Surrounding Air
Temperature IP20, NEMA
Type Open: 0 to 50 degrees C (32 to 122 degrees F), typical.
Storage Temp. (all const.): –25 to 55 degrees C (–13 to 131 degrees F)
Atmosphere: Important: Drive must not be installed in an area where
the ambient atmosphere contains volatile or corrosive
gas, vapors or dust. If the drive is not going to be installed
for a period of time, it must be stored in an area where it
will not be exposed to a corrosive atmosphere.
Relative Humidity: Operating: 5 to 85% non-condensing
Storage: 5 - 95% non-condensing
Shock: 15G peak for 11ms duration (±1.0 ms)
Vibration: 0.152 mm (0.006 in.) displacement, 1G peak
(1)
PowerFlex DC drives must be installed in a Pollution Degree 2 environment.

A-2 Supplemental Drive Information
Drive Type Full Wave Regen, 6 Pulse, Regulated Field Supply
Electrical Input Voltages: 230 to 480V AC +/- 10%, 3 Phase
Input Frequency: 50/60 Hz +/- 5%
Armature Output Voltage: Two Quadrant Drives Four Quadrant Drives
260V DC @ 230V AC 240V DC @ 230V AC
470V DC @ 400V AC 420V DC @ 400V AC
530V DC @ 440V AC 460V DC @ 440V AC
560V DC @ 460V AC 480V DC @ 460V AC
580V DC @ 480V AC 500V DC @ 480V AC
Output Horsepower (Cont.) 1.5 to 150 HP @ 230V AC
2 to 400 HP @ 460V AC
Output Current: 4.1 to 667A
Overload Capability: 100% rated continuous current
150% rated current for one minute then fault
200% rated current for three seconds then fault
Field Output Voltage 200V DC @ 230V AC
310V DC @ 400V AC
360V DC @ 460V AC
Maximum field output voltage is 0.85 x AC input line
voltage.
Controller Current Overload: 150% rated current for one minute
200% rated current for three seconds
Max. Short Circuit Rating: 100,000 A, with the following exceptions:
• 230V AC input, 521 A, two quadrant drives are short
circuit rated at 10,000 A
• 460V AC input, 495 A and 667 A, two quadrant drives
are short circuit rated at 18,000 A
Control Speed Regulation:* All operating modes:
Max. speed: 8000 rpm
Digital reference resolution: 0.25 rpm
Analog reference resolution: ≥ 0.25 rpm
with Digital Incremental Encoder
Speed feedback resolution 0.5 rpm
Operating range better than 1000:1 rpm, bi-directional
Performance Accuracy ±0.02% typical
170 rad/sec bandwidth
with DC Analog Tachometer
Speed feedback resolution better than 2000:1 rpm
Performance accuracy ±0.1%
with Armature Voltage Feedback
Voltage feedback resolution better than 2000:1 rpm
Performance accuracy: ±2.0% typical
*Subject to motor specs, current loop tuning.
Torque Regulation Current feedback resolution better than 2000:1 rpm
Performance accuracy: 1.0% typical

Supplemental Drive Information A-3
Feedback Encoder Type: Incremental, dual channel, two channel optional
Devices (with jumper), differential (recommended) or
single-ended
Input Voltage: Configurable for +2.5V - 5.2V (switch S21
in ENC_5 position) or +5.4V - 15.2V (switch S21 in
ENC_12 position)
Input Current: 4.5 mA / 6.8 - 10.9 mA each channel
Quadrature: 90° ± 27° @ 25° C
Duty cycle: 50% ± 10% Source/Sink capable
Pulses Per Revolution: 600 to 9999
Maximum Frequency: 150 kHz
Maximum Cable Length: Shielded, 150m (0.75 mm2),
125m (0.5 mm2), 55m (0.22 mm2)
DC Analog Tachometer Input Voltage: 22.7, 45.4, 90.7, 181.6, & 302.9V max.
Input Current: 8 mA full scale
Maximum Cable Length: Shielded, depends on the
installation, typical 150m.
Inputs Analog Inputs Three configurable, isolated, differential
±10V, 0-10V, 0-20mA or 4-20mA.
Digital Inputs Eight standard configurable, four additional configurable
with the I/O Expansion circuit board.
Max Voltage +30V DC input, 200mA (total current draw is
the sum of encoder power, digital outputs and any other
loads connected to terminal 19)
Outputs Analog Outputs Two standard configurable, two additional configurable
with the I/O Expansion circuit board. Sampling rate 2 ms.
± 10V, 5mA, bipolar (current is not bipolar)
Digital Outputs Four standard configurable, four additional configurable
with the I/O Expansion circuit board.
+ 30V, 50mA
Relay Outputs Two configurable, N.O. contacts
Max. 250V AC, 1A AC1

IP20 (NEMA UL/Type Open) Watts loss data shown below is based on the rated current of the drive.
Watts Loss Important: For drives with 230V input, rated 150 HP / 521 A, the cooling
fans must be powered by an external 230V 50/60 Hz power
supply at terminals U3 & V3.
Frame
Code(1) Total Watts Fans
@ 230V @ 460V Loss (W) Voltage (V) Rated Current (A) Air Capacity (m3/h)
A 7P0 4P1
9P0 6P0
012 010 131 – – –
020 014
– 019
029 027 186 – – –
038 035
055 045 254 80
– 052
073 073 408 160
093 086
476 160
110 –
– 100
553 160
– 129 Internal power supply
B 146 167
781 320
180 –
218 207 939 320
265 250 1038 320
– 330 1248 320
360 412
1693 680
434 –
C 521 495 2143 230 0.75 1050
– 667 2590 230 0.75 1050
(1) Refer to Catalog Number Explanation on page Preface-4, positions 8-10 for corresponding drive HP rating,

Communication Typical Programmable Controller Configurations

Configurations
Important: If block transfers are programmed to continuously write information to the drive, care must
be taken to properly format the block transfer. If attribute 10 is selected for the block
transfer, values will be written only to RAM and will not be saved by the drive. This is the
preferred attribute for continuous transfers. If attribute 9 is selected, each program scan
will complete a write to the drives non-volatile memory (EEprom). Since the EEprom has
a fixed number of allowed writes, continuous block transfers will quickly damage the
EEprom. Do Not assign attribute 9 to continuous block transfers. Refer to the individual
communications adapter User Manual for additional details.
Logic Command/Status Words

Refer to parameter 1328 [Drive Logic Rslt] for more information.
Figure A.1 Logic Command Word
Logic Bits
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Command Description
x Stop (1) 0 = Not Stop
1 = Stop
x Start (1)(2) 0 = Not Start
1 = Start
x Jog 0 = Not Jog
1 = Jog
x Clear 0 = Not Clear Faults
Faults 1 = Clear Faults
x x Direction 00 = No Command
01 = Forward Command
10 = Reverse Command
11 = Hold Present Direction
x Local 0 = No Local Control
Control 1 = Local Control
x MOP 0 = Not Increment
Increment 1 = Increment
x x Accel Rate 00 = No Command
01 = Use Accel Time 1
10 = Use Accel Time 2
11 = Use Present Time
x x Decel 00 = No Command
Rate 01 = Use Decel Time 1
10 = Use Decel Time 2
11 = Use Present Time
x x x Reference 000 = No Command
Select (3) 001 = Ref. 1 (Spd Ref A)
010 = Ref. 2 (Spd Ref B)
011 = Ref. 3 (Preset Spd 3)
x MOP 0 = Not Decrement
Decrement 1 = Decrement
(1)
A “0 = Not Stop” condition (logic 0) must first be present before a “1 = Start” condition will start the drive. The
Start command acts as a momentary Start command. A “1” will start the drive, but returning to “0” will not stop
the drive.
(2) This Start will not function if a digital input (parameters 131- 144) is programmed for 2-Wire Control (option 5
“Run”, 6 “Run Forward” or 7 “Run Reverse”).
(3)
This Reference Select will not function if a digital input (parameters 131- 144) is programmed for “Speed Sel 1,
2 or 3” (option 17, 18 or 19). Note that Reference Selection is “Exclusive Ownership” see [Reference Owner] on
page 3-59.

Figure A.2 Logic Status Word

Logic Bits
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Status Description
x Ready 0 = Not Ready
1 = Ready
x Active 0 = Not Active
1 = Active
x Command 0 = Reverse
Direction 1 = Forward
x Actual 0 = Reverse
Direction 1 = Forward
x Accel 0 = Not Accelerating
1 = Accelerating
x Decel 0 = Not Decelerating
1 = Decelerating
x Alarm 0 = No Alarm
1 = Alarm
x Fault 0 = No Fault
1 = Fault
x At Speed 0 = Not At Reference
1 = At Reference
x x x Local 000 = Port 0 (TB)
Control (1) 001 = Port 1
010 = Port 2
011 = Port 3
100 = Port 4
101 = Port 5
110 = Reserved
111 = No Local
x x x x Reference 0000 = Spd Ref A Auto
Source 0001 = Spd Ref B Auto
0010 = Preset Spd 2 Auto
1000 = Term Blk Manual
1001 = DPI 1 Manual
1010 = DPI 2 Manual
1011 = DPI 3 Manual
1100 = DPI 4 Manual
1101 = DPI 5 Manual
1110 = Reserved
1111 = Jog Ref
(1) Refer to Masks & Owners on page 3-58 for further information.

Drive Power Circuit The tables on the following pages provide drive ratings and the
Protection recommended fuses for protecting the armature and field circuits.
Externally mounted fuses (as indicated in Figure A.3 on page A-7) must be
sourced separately when installing the drive. Internally mounted fuses are
provided with the drive.
Frame A and B Fuse Information

Figure A.3 Frame A and B Fuse Table Designations
FS1 = Externally
FS1
mounted fuses for
the armature
converter on the
AC input side.
U V W U1 V1 FS3 = Internally
mounted fuses
FS3
for the field
circuit on the AC
C D C1 D1 input side.
FS2 = Externally FS2

mounted fuses for
the armature
circuit on the DC
side.
M
Table A.A AC Input Line Fuses - 230V AC Input Frame A and B (Regenerative and
Non-Regenerative Drives)
Fuse Code FS1 (See Figure A.3 above)
Drive Bussmann Ferraz Shawmut (Gould Shawmut)
Current AC North
Frame
Rating DC Line Ferrule FWP Ferrule North American American Ferrule A70QS North American
Code Amps Amps Type Fuse Block FWP Type Fuse Block Type A70P / A70QS Type
A 7P0 7 5.7 FWP-10A14F CH143D FWP-10B – A70QS10-14F A70P10-4
9P0 9 7.4 FWP-15A14F FWP-15B – A70QS16-14F A70P15-4
012 12 9.8 FWP-20A14F FWP-20B – A70QS20-14F A70P20-4
020 20 16 FWP-25A14F FWP-25B – A70QS25-14F A70QS25-4
029 29 24 FWP-40A22F CH223D FWP-40B – A70QS40-22F A70QS40-4
073 73 60 – – FWP-100A ST14 – A70QS100-4K
093 93 76 – – FWP-150A – A70QS150-4K
110 110 90 – – FWP-175A – A70QS175-4K
B 146 146 119 – – FWP-250A – A70QS250-4
180 180 147 – – FWP-300A – A70QS300-4
218 218 178 – – FWP-350A – A70QS350-4
265 265 217 – – FWP-400A ST38-72612 – A70QS400-4
360 360 294 – – FWP-600A – A70QS600-4K
434 434 355 – – FWP-600A – A70QS600-4

Table A.B Recommended AC Input Line Fuses - 460V AC Input Frame A and B
(Regenerative and Non-Regenerative Drives)
Fuse Code FS1 (See Figure A.3 on page A-7)
Current AC North
Frame
Rating DC Line Ferrule FWP Ferrule North American American Ferrule A70QS North American
Code Amps Amps Type Fuse Block FWP Type Fuse Block Type A70P / A70QS Type
A 4P1 4.1 3.3 FWP-10A14F CH143D FWP-10B – A70QS10-14F A70P10-4
027 37 22.1 FWP-40A22F CH223D FWP-40B – A70QS40-22F A70QS40-4
035 35 28.6 FWP-63A22F FWP-60B – A70QS63-22F A70QS60-4
073 73 59.6 – – FWP-100A ST14 – A70QS100-4K
086 86 70.3 – – FWP-150A – A70QS150-4K
100 100 81.7 – – FWP-175A – A70QS175-4K
129 129 105.4 – – FWP-175A – A70QS175-4K
B 167 167 136.4 – – FWP-300A – A70QS300-4
207 207 169.1 – – FWP-350A – A70QS350-4
250 250 204.3 – – FWP-400A ST38-72612 – A70QS400-4
330 330 269.6 – – FWP-600A – A70QS600-4K
412 412 336.6 – – FWP-600A – A70QS600-4
Table A.C Recommended Armature DC Output Fuses - 230V AC Input Frame A and B
(Regenerative Drives Only)
Fuse Code FS2(1) (See Figure A.3 on page A-7)
Current AC North
Frame
Rating DC Line Ferrule FWP Ferrule North American American Ferrule North American
Code Amps Amps Type Fuse Block FWP Type Fuse Block A70QS Type A70P / A70QS Type
A 7P0 7 5.7 FWP-15A14F CH142D FWP-15B – A70QS16-14F A70P15-4
029 29 24 FWP-63A22F CH222D FWP-60B – A70QS63-22F A70QS60-4
055 55 45 – – FWP-125A ST14 – A70QS125-4K
073 73 60 – – FWP-150A – A70QS150-4K
093 93 76 – – FWP-200A – A70QS200-4K
110 110 90 – – FWP-225A – A70QS250-4
B 146 146 119 – – FWP-300A – A70QS300-4
180 180 147 – – FWP-350A A70QS350-4
218 218 178 – – FWP-450A ST38-72612 – A70QS450-4
265 265 217 – – FWP-600A – A70QS600-4K
360 360 294 – – FWP-700A – A70QS700-4
434 434 355 – – FWP-900A – – A70P900-4
(1) Required on four quadrant drives only, highly recommended on two quadrant drives.

Table A.D Recommended Armature DC Output Fuses - 460V AC Input Frame A and B
(Regenerative Drives Only)
Fuse Code FS2(1) (See Figure A.3 on page A-7)
Current AC North
Frame
Rating DC Line Ferrule FWP Ferrule North American American Ferrule North American
Code Amps Amps Type Fuse Block FWP Type Fuse Block A70QS Type A70P / A70QS Type
A 4P1 4.1 3.3 FWP-10A14F CH142D FWP-10B – A70QS10-14F A70P10-4
027 37 22.1 FWP-63A22F CH222D FWP-60B – A70QS63-22F A70QS60-4
045 45 36.8 FWP-100A22F FWP-90B – – A70QS90-4
052 52 42.5 FWP-100A22F FWP-100B – – A70QS100-4
073 73 59.6 – – FWP-150A ST14 – A70QS150-4K
086 86 70.3 – – FWP-175A – A70QS175-4K
100 100 81.7 – – FWP-200A – A70QS200-4K
129 129 105.4 – – FWP-250A – A70QS250-4
B 167 167 136.4 – – FWP-350A – A70QS350-4
207 207 169.1 – – FWP-400A – A70QS400-4
250 250 204.3 – – FWP-500A ST38-72612 – A70QS500-4K
330 330 269.6 – – FWP-700A – A70QS700-4
412 412 336.6 – – FWP-800A – A70QS800-4
(1) Required on four quadrant drives only, highly recommended on two quadrant drives.
Table A.E Recommended Field Circuit Fuses - 230V AC Input Frame A and B
Drive Fuse Code FS3(1) (SeeFigure A.3 on page A-7, Figure A.4 on
Current page A-10 and Figure A.5 on page A-11 for location)
Frame
Rating Field Ferraz Shawmut

Code Amps Type Bussmann (Gould Shawmut) SIBA
A 7P0 10 6 x 32 mm FWH-016A6F E085449 70 125 40.16
9P0
012
020
029
038
055
073 14
093
110
B 146 20 10 x 38 mm FWC-25A10F A60Q25-2 60 033 05.25
180
218
265
360
434
(1) Internal fuses - provided with the drive.

Table A.F Recommended Field Circuit Fuses - 460V AC Input Frame A and B
Drive Fuse Code FS3(1) (SeeFigure A.3 on page A-7, Figure A.4 below
Current and Figure A.5 on page A-11 for location)
Frame
A 4P1 10 6 x 32 mm FWH-016A6F E085449 70 125 40.16
6P0
010
014
019
027
035
045
052
073 14
086
100
129
B 167 20 10 x 38 mm FWC-25A10F A60Q25-2 60 033 05.25
207
250
330
412
(1) Internal fuses - provided with the drive.
Figure A.4 Frame A Field Circuit Fuses Location
Bottom View of Drive with Fan Bottom View of Drive without Fan
Field circuit fuses

Figure A.5 Frame B Field Circuit Fuses Location
Top View of Drive
Field circuit fuses
Frame C Fuse Information

All AC input fuses for armature and field circuit protection are internally
mounted and provided with frame C PowerFlex DC drives with 230V AC
input and a current rating of 521A and 460V AC input and a current rating
of 495A and 667A.
Figure A.6 Frame C Fuse Table Designations
FS4 = Internally U V W U1 V1 FS3 = Internally

mounted fuses for FS4 mounted fuses
FS3
the armature for the field
converter on the circuit on the AC
AC input side. C D C1 D1 input side.

Table A.G Recommended Field Circuit Fuses - 230V AC Input Frame C (Regenerative
and Non-Regenerative Drives)
Drive Fuse Code FS3 (See Figure A.6 on page A-11 and Figure A.7
Current below for location)
521 20 10 x 38 mm FWC-25A10F A60Q25-2 60 033 05.25
Table A.H Recommended Field Circuit Fuses -460V AC Input Frame C (Regenerative
and Non-Regenerative Drives)
Drive Fuse Code FS3 (See Figure A.6 on page A-11 and Figure A.7
Current below for location)
495 20 10 x 38 mm FWC-25A10F A60Q25-2 60 033 05.25
667 A60Q25-8
Figure A.7 Frame C Field Circuit Fuse Location

Field circuit fuses are located on the Control EMI
shield, which holds the Control board.
Note: Drive shown with front covers removed.

Table A.I Recommended Leg Fuses - 230V AC Input Frame C (Regenerative Drives
Only)
Drive Fuse Code FS4 (See Figure A.6 on page A-11 and Figure A.8 below for location)
Current AC Bussmann Ferraz Shawmut (Gould Shawmut) SIBA
Rating DC Line
Code Amps Amps Square Body - Flush End Contact
521 521 426 170M5464 + switch 170H0069 6,9 URD 32 TTF 800 + switch MS3-V1-5BS 20 671 32.800 + switch 2800104
Table A.J Recommended Leg Fuses - 460V AC Input Frame C (Regenerative Drives
Only)
Drive Fuse Code FS4 (See Figure A.6 on page A-11 and Figure A.9 on page A-14 for location)
Rating DC Line
495 495 404.4 170M5462 + switch 170H0069 6,9 URD 32 TTF 630 + switch MS3-V1-5BS 20 671 32.630 + switch 2800104
Figure A.8 Frame C Regenerative Drive - Leg Fuse Location

Leg fuses and switches are located on the bus bars behind the
Control EMI shield, which holds the Control board.
Note: Drive shown with front covers removed and Control EMI shield lowered.

Table A.K Recommended AC Input Line Fuses - 230V AC Input Frame C

(Non-Regenerative Drives Only)
Drive Fuse Code FS4 (See Figure A.6 on page A-11 and Figure A.8 below for location)
Rating DC Line
521 521 426 170M5466 + switch 170H0069 6,9 URD 32 TTF 1000 + switch MS3-V1-5BS 20 671 32.1000 + switch 2800104
Table A.L Recommended AC Input Line Fuses - 460V AC Input Frame C

(Non-Regenerative Drives Only)
Drive Fuse Code FS4 (See Figure A.6 on page A-11 and Figure A.9 on page A-14 for location)
Rating DC Line
Figure A.9 Frame C Non-Regenerative Drive - AC Input Line Fuse Location

AC Input fuses and switches are located on the bus bars behind
the Control EMI shield, which holds the Control board.
Note: Drive shown with front covers removed and Control EMI shield lowered.

Control Power Circuit The following fuses are used to protect the Switching Power Supply circuit
Protection Fuses and the MOVs on the Pulse Transformer circuit board (frame B drives only)
or Transient Noise Filter circuit board (frame C drives only).
Frame Mounted on Designation Fuse
A Switching Power Supply circuit board F1 1A, 250V slow, 5x20mm
B and C Switching Power Supply circuit board F1 3.15A, 250V slow, 5x20mm
F2 2.5A, 250V fast, 5x20mm
B Pulse Transformer circuit board F1/F2/F3 16A, 500V fast, 6x32mm
C Transient Noise Filter circuit board F11/F21/F31 25A, 500V fast, 6x32mm
Figure A.10 Frame A Switching Power Supply Fuse Location
Top View of Drive
Switching Power Supply fuse
Figure A.11 Frame B Switching Power Supply Fuse Location
Top View of Drive
F1 = 3.15A fuse F2 = 2.5A fuse

Figure A.12 Frame C Switching Power Supply Fuse Location
F1 = 3.15A fuse F2 = 2.5A fuse

Fuses are located on the Switching Power Supply circuit board (SW-2)
on the back of the Control EMI shield, which holds the Control board.

AC Input Line Reactors and If a DC Contactor is used, an AC Input contactor is not needed.
AC Input Contactors
Table A.M 230V AC Input, Regenerative Drives
AC Line IP00 (Open Style) Line Reactor
Drive Cat. No. DC Amps Amps HP Cat No. Line Reactor kW (HP) AC Input Contactor Cat. No.
20P-41AB7P0 7 5.7 1.5 1321-3R8-A .75 (1) 100-C12D10
20P-41AB9P0 9 7.4 2 1321-3R12-A 1.49 (2) 100-C12D10
20P-41AB012 12 9.8 3 1321-3R18-A 0.75-3.7 (1-5) 100-C12D10
20P-41AB020 20 16 5 1321-3R18-A 0.75-3.7 (1-5) 100-C23D10
20P-41AB029 29 24 7.5 1321-3R55-A 5.5-11 (7.5-15) 100-C30D10
20P-41AB038 38 31 10 1321-3R55-A 5.5-11 (7.5-15) 100-C37D10
20P-41AB055 55 45 15 1321-3R55-A 5.5-11 (7.5-15) 100-C60D10
20P-41AB073 73 60 20 1321-3R80-A 15 (20) 100-C60D10
20P-41AB093 93 76 25 1321-3R100-A 18.5-22 (25-30) 100-C85D10
20P-41AB110 110 90 30 1321-3R100-A 18.5-22 (25-30) 100-D110D11
20P-41AB146 146 119 40 1321-3R160-A 30-37 (40-50) 100-D140D11
20P-41AB180 180 147 50 1321-3R160-A 30-37 (40-50) 100-D180D11
20P-41AB218 218 178 60 1321-3RB250-A 45-56 (60-75) 100-D180D11
20P-41AB265 265 217 75 1321-3RB250-A 45-56 (60-75) 100-D250ED11
20P-41AB360 360 294 100 1321-3RB320-A 75 (100) 100-D300ED11
20P-41AB434 434 355 125 1321-3RB400-A 93 (125) 100-D420ED11
20P-41AB521 521 426 150 1321-3R500-A 112 (150) 100-D630ED11
Table A.N 230V AC Input, Non-Regenerative Drives

AC Line IP00 (Open Style)
Drive Cat. No. DC Amps Amps HP Line Reactor Cat No. Line Reactor kW (HP) AC Input Contactor Cat. No.
20P-21AB7P0 7 5.7 1.5 1321-3R8-A .75 (1) 100-C12D10
20P-21AB9P0 9 7.4 2 1321-3R12-A 1.49 (2) 100-C12D10
20P-21AB012 12 9.8 3 1321-3R18-A 0.75-3.7 (1-5) 100-C12D10
20P-21AB020 20 16 5 1321-3R18-A 0.75-3.7 (1-5) 100-C23D10
20P-21AB029 29 24 7.5 1321-3R55-A 5.5-11 (7.5-15) 100-C30D10
20P-21AB038 38 31 10 1321-3R55-A 5.5-11 (7.5-15) 100-C37D10
20P-21AB055 55 45 15 1321-3R55-A 5.5-11 (7.5-15) 100-C60D10
20P-21AB073 73 60 20 1321-3R80-A 15 (20) 100-C60D10
20P-21AB093 93 76 25 1321-3R100-A 18.5-22 (25-30) 100-C85D10
20P-21AB110 110 90 30 1321-3R100-A 18.5-22 (25-30) 100-D110D11
20P-21AB146 146 119 40 1321-3R160-A 30-37 (40-50) 100-D140D11
20P-21AB180 180 147 50 1321-3R160-A 30-37 (40-50) 100-D180D11
20P-21AB218 218 178 60 1321-3RB250-A 45-56 (60-75) 100-D180D11
20P-21AB265 265 217 75 1321-3RB250-A 45-56 (60-75) 100-D250ED11
20P-21AB360 360 294 100 1321-3RB320-A 75 (100) 100-D300ED11
20P-21AB434 434 355 125 1321-3RB400-A 93 (125) 100-D420ED11
20P-21AB521 521 426 150 1321-3R500-A 112 (150) 100-D630ED11

Table A.O 460V AC Input, Regenerative Drives

20P-41AD4P1 4.1 3.3 2 1321-3R4-A .55 (.75) 100-C12D10
20P-41AD6P0 6 4.9 3 1321-3R8-A .75 (1) 100-C12D10
20P-41AD010 10 8.2 5 1321-3R18-B 1.5-7.5 (2-10) 100-C12D10
20P-41AD014 14 11.4 7.5 1321-3R18-B 1.5-7.5 (2-10) 100-C12D10
20P-41AD019 19 15.5 10 1321-3R18-B 1.5-7.5 (2-10) 100-C23D10
20P-41AD027 27 22.1 15 1321-3R55-B 11-22 (15-30) 100-C23D10
20P-41AD035 35 28.6 20 1321-3R55-B 11-22 (15-30) 100-C30D10
20P-41AD045 45 36.8 25 1321-3R55-B 11-22 (15-30) 100-C37D10
20P-41AD052 52 42.5 30 1321-3R55-B 11-22 (15-30) 100-C43D10
20P-41AD073 73 59.6 40 1321-3R80-B 30 (40) 100-C60D10
20P-41AD086 86 70.3 50 1321-3R100-B 37-45 (50-60) 100-C85D10
20P-41AD100 100 81.7 60 1321-3R100-B 37-45 (50-60) 100-C85D10
20P-41AD129 129 105.4 75 1321-3R160-B 56-75 (75-100) 100-D110D11
20P-41AD167 167 136.4 100 1321-3R160-B 56-75 (75-100) 100-D140D11
20P-41AD207 207 169.1 125 1321-3RB250-B 93-112 (125-150) 100-D180D11
20P-41AD250 250 204.3 150 1321-3RB250-B 93-112 (125-150) 100-D210ED11
20P-41AD330 330 269.6 200 1321-3RB320-B 149 (200) 100-D300ED11
20P-41AD412 412 336.6 250 1321-3RB400-B 186.4 (250) 100-D420ED11
20P-41AD495 495 404.4 300 1321-3R500-B 223.7 (300) 100-D420ED11
20P-41AD667 667 544.9 400 1321-3R600-B 298.3 (400) 100-D630ED11
Table A.P 460V AC Input, Non-Regenerative Drives

20P-21AD4P1 4.1 3.3 2 1321-3R4-A .55 (.75) 100-C12D10
20P-21AD6P0 6 4.9 3 1321-3R8-A .75 (1) 100-C12D10
20P-21AD010 10 8.2 5 1321-3R18-B 1.5-7.5 (2-10) 100-C12D10
20P-21AD014 14 11.4 7.5 1321-3R18-B 1.5-7.5 (2-10) 100-C12D10
20P-21AD019 19 15.5 10 1321-3R18-B 1.5-7.5 (2-10) 100-C23D10
20P-21AD027 27 22.1 15 1321-3R55-B 11-22 (15-30) 100-C23D10
20P-21AD035 35 28.6 20 1321-3R55-B 11-22 (15-30) 100-C30D10
20P-21AD045 45 36.8 25 1321-3R55-B 11-22 (15-30) 100-C37D10
20P-21AD052 52 42.5 30 1321-3R55-B 11-22 (15-30) 100-C43D10
20P-21AD073 73 59.6 40 1321-3R80-B 30 (40) 100-C60D10
20P-21AD086 86 70.3 50 1321-3R100-B 37-45 (50-60) 100-C85D10
20P-21AD100 100 81.7 60 1321-3R100-B 37-45 (50-60) 100-C85D10
20P-21AD129 129 105.4 75 1321-3R160-B 56-75 (75-100) 100-D110D11
20P-21AD167 167 136.4 100 1321-3R160-B 56-75 (75-100) 100-D140D11
20P-21AD207 207 169.1 125 1321-3RB250-B 93-112 (125-150) 100-D180D11
20P-21AD250 250 204.3 150 1321-3RB250-B 93-112 (125-150) 100-D210ED11
20P-21AD330 330 269.6 200 1321-3RB320-B 149 (200) 100-D300ED11
20P-21AD412 412 336.6 250 1321-3RB400-B 186.4 (250) 100-D420ED11
20P-21AD495 495 404.4 300 1321-3R500-B 223.7 (300) 100-D420ED11
20P-21AD667 667 544.9 400 1321-3R600-B 298.3 (400) 100-D630ED11

DC Output Contactors and

Dynamic Brake Resistor
Table A.Q 230V AC Input, Regenerative Drives
Kits
Dynamic DB
Brake Armature DB Resistor Brake DC Loop DC Contactor
DC AC Line Resistor Kit Voltage Resistor Size Amps Contactor Cat. Crimp Lugs Cat.
Drive Cat. No. Amps Amps HP Cat. No. (Volts) Size (ohms) (Watts) Required No.(3) No.(6)
20P-41AB7P0 7 5.7 1.5 1370-DBL62 240 20 420 12.00 1370-DC56 1370-LG40
20P-41AB9P0 9 7.4 2 1370-DBL63 240 20 420 12.00 1370-DC56 1370-LG40
20P-41AB012 12 9.8 3 1370-DBL64 240 15 420 16.00 1370-DC56 1370-LG40
20P-41AB020 20 16 5 1370-DBL65 240 8.6 420 27.91 1370-DC56 1370-LG40
20P-41AB029 29 24 7.5 1370-DBL66 240 6 345 40.00 1370-DC56 1370-LG40
20P-41AB038 38 31 10 1370-DBL67 240 5 330 48.00 1370-DC56 1370-LG40
20P-41AB055 55 45 15 1370-DBL68 240 3.5 385 68.57 1370-DC56 1370-LG56
20P-41AB073 73 60 20 1370-DBL69 240 2.6 385 92.31 1370-DC110 1370-LG92
20P-41AB093 93 76 25 1370-DBL70 240 2 330 120.00 1370-DC110 1370-LG92
20P-41AB110 110 90 30 1370-DBL71 240 2 330 120.00 1370-DC110 1370-LG110
20P-41AB146 146 119 40 1370-DBL72 240 0.7 280 342.86 1370-DC180 1370-LG160
20P-41AB180 180 147 50 1370-DBL73 240 0.5 365 480.00 1370-DC180 1370-LG180
20P-41AB218 218 178 60 1370-DBL74 240 0.5 365 480.00 1370-DC280 1370-LG228
20P-41AB265 265 217 75 1370-DBL75 240 2 330 120.00 1370-DC280 1370-LG268
20P-41AB360 360 294 100 1370-DBL76 240 1.4 290 171.43 (4) (7)
20P-41AB434 434 355 125 (1) 240 0.5 1458 651 (5) (7)
(5) (7)
20P-41AB521 521 426 150 (2) 240 0.322 6221 781
(1)
Qty 4-CUTLER-HAMMER_G3AP50 Two in series, two in parallel. Must be sourced separately from drive.
(2)
HUBBELL_Y139W322GB - Must be sourced separately from drive.
(3) Coil voltage = 115V AC, 50/60Hz.
(4)
ABB_EHDB360C-1L-22 - ABB Contactor for drives with a dynamic brake. Must be sourcing separately from drive.
(5)
ABB_EHDB520C2P-1L - ABB Contactor for drives with no Dynamic Brake. ABB_EHDB520C-1L - ABB Contactor for drives with Dynamic Brake. Must be sourced separately from drive.
(6) See DC Contactor Crimp Lug Kit Specifications on page A-21 for more information.
(7)
Wire and Lug size dependant on Cabinet dims and local codes.
Table A.R 230V AC Input, Non-Regenerative Drives

Dynamic DB DB
AC Brake Armature Resistor Resistor Brake DC Loop DC Contactor
Drive Cat. DC Line Resistor Kit Voltage Size Size Amps Contactor Cat. Crimp Lugs Cat.
No. Amps Amps HP Cat. No. (Volts) (ohms) (Watts) Required No.(3) No.(6)
20P-21AB7P0 7 5.7 1.5 1370-DBL62 240 20 420 12.00 1370-DC56 1370-LG40
20P-21AB9P0 9 7.4 2 1370-DBL63 240 20 420 12.00 1370-DC56 1370-LG40
20P-21AB012 12 9.8 3 1370-DBL64 240 15 420 16.00 1370-DC56 1370-LG40
20P-21AB020 20 16 5 1370-DBL65 240 8.6 420 27.91 1370-DC56 1370-LG40
20P-21AB029 29 24 7.5 1370-DBL66 240 6 345 40.00 1370-DC56 1370-LG40
20P-21AB038 38 31 10 1370-DBL67 240 5 330 48.00 1370-DC56 1370-LG40
20P-21AB055 55 45 15 1370-DBL68 240 3.5 385 68.57 1370-DC56 1370-LG56
20P-21AB073 73 60 20 1370-DBL69 240 2.6 385 92.31 1370-DC110 1370-LG92
20P-21AB093 93 76 25 1370-DBL70 240 2 330 120.00 1370-DC110 1370-LG92
20P-21AB110 110 90 30 1370-DBL71 240 2 330 120.00 1370-DC110 1370-LG110
20P-21AB146 146 119 40 1370-DBL72 240 0.7 280 342.86 1370-DC180 1370-LG160
20P-21AB180 180 147 50 1370-DBL73 240 0.5 365 480.00 1370-DC180 1370-LG180
20P-21AB218 218 178 60 1370-DBL74 240 0.5 365 480.00 1370-DC280 1370-LG228
20P-21AB265 265 217 75 1370-DBL75 240 2 330 120.00 1370-DC280 1370-LG268
20P-21AB360 360 294 100 1370-DBL76 240 1.4 290 171.43 (4) (7)
20P-21AB434 434 355 125 (1) 240 0.5 1458 – (5) (7)
(5) (7)
20P-21AB521 521 426 150 (2) 240 0.322 6221 –
(1)
Qty 4-CUTLER-HAMMER_G3AP50 Two in series, two in parallel. Must be sourced separately from drive.
(2)
(3) Coil voltage = 115V AC, 50/60Hz.
(4)
(5)
ABB_EHDB520C2P-1L - ABB Contactor for drives with no Dynamic Brake. ABB_EHDB520C-1L - ABB Contactor for drives with Dynamic Brake. Must be sourced separately from drive.
(7)

Table A.S 460V AC Input, Regenerative Drives

Dynamic
AC Brake Armature DB Brake DC Loop DC Contactor
Drive Cat. DC Line Resistor Kit Voltage Resistor DB Resistor Amps Contactor Cat. Crimp Lugs Cat.
No. Amps Amps HP Cat. No. (Volts) Size (ohms) Size (Watts) Required No.(4) No.(9)
20P-41AD4P1 4.1 3.3 2 1370-DBH63 500 81 255 6.17 1370-DC56 1370-LG40
20P-41AD6P0 6 4.9 3 1370-DBH64 500 62 245 8.06 1370-DC56 1370-LG40
20P-41AD010 10 8.2 5 1370-DBH65 500 45 245 11.11 1370-DC56 1370-LG40
20P-41AD014 14 11.4 7.5 1370-DBH66 500 27 350 18.52 1370-DC56 1370-LG40
20P-41AD019 19 15.5 10 1370-DBH67 500 20 420 25.00 1370-DC56 1370-LG40
20P-41AD027 27 22.1 15 1370-DBH68 500 12 405 41.67 1370-DC56 1370-LG40
20P-41AD035 35 28.6 20 1370-DBH69 500 5 330 100.00 1370-DC56 1370-LG40
20P-41AD045 45 36.8 25 1370-DBH70 500 4.5 330 111.11 1370-DC56 1370-LG52
20P-41AD052 52 42.5 30 1370-DBH71 500 3.5 385 142.86 1370-DC56 1370-LG52
20P-41AD073 73 59.6 40 1370-DBH72 500 2.6 345 192.31 1370-DC110 1370-LG92
20P-41AD086 86 70.3 50 1370-DBH73 500 2 345 250.00 1370-DC110 1370-LG92
20P-41AD100 100 81.7 60 1370-DBH74 500 2 345 250.00 1370-DC110 1370-LG110
20P-41AD129 129 105.4 75 1370-DBH75 500 1 270 500.00 1370-DC180 1370-LG140
20P-41AD167 167 136.4 100 1370-DBH76 500 0.7 280 714.29 1370-DC180 1370-LG180
20P-41AD207 207 169.1 125 1370-DBH77 500 0.7 280 714.29 1370-DC280 1370-LG228
20P-41AD250 250 204.3 150 1370-DBH78 500 0.5 365 1000.00 1370-DC280 1370-LG268
20P-41AD330 330 269.6 200 1370-DBH79 500 0.7 280 714.29 (5) (10)
20P-41AD412 412 336.6 250 (1) 500 0.808 7292 – (6) (10)
20P-41AD495 495 404.4 300 (2) 500 0.595 6069 – (7) (10)
20P-41AD667 667 544.9 400 (3) 500 0.542 6439 – (8) (10)
(1)
(2)
(3) HUBBELL_Y109W542GB - Must be sourced separately from drive.
(4)
Coil voltage = 115V AC, 50/60Hz.
(5)
(6) ABB_EHDB520C2P-1L - ABB contactor for drives with no dynamic brake. ABB_EHDB520C-1L - ABB contactor for drives with a dynamic brake. Must be sourced separately from drive.
(7)
ABB_EHDB650C2P-1L - ABB contactor for drives with no dynamic brake. ABB_EHDB650C-1L - ABB contactor for drives with a dynamic brake. Must be sourced separately from drive.
(8)
(10)

Table A.T 460V AC Input, Non-Regenerative Drives

DB
AC Armature Resistor Brake DC Loop DC Contactor
DC Line Dynamic Brake Voltage DB Resistor Size Amps Contactor Crimp Lugs Cat.
Drive Cat. No. Amps Amps HP Resistor Kit Cat. No. (Volts) Size (ohms) (Watts) Required Cat. No.(4) No.(9)
20P-21AD4P1 4.1 3.3 2 1370-DBH63 500 81 255 6.17 1370-DC56 1370-LG40
20P-21AD6P0 6 4.9 3 1370-DBH64 500 62 245 8.06 1370-DC56 1370-LG40
20P-21AD010 10 8.2 5 1370-DBH65 500 45 245 11.11 1370-DC56 1370-LG40
20P-21AD014 14 11.4 7.5 1370-DBH66 500 27 350 18.52 1370-DC56 1370-LG40
20P-21AD019 19 15.5 10 1370-DBH67 500 20 420 25.00 1370-DC56 1370-LG40
20P-21AD027 27 22.1 15 1370-DBH68 500 12 405 41.67 1370-DC56 1370-LG40
20P-21AD035 35 28.6 20 1370-DBH69 500 5 330 100.00 1370-DC56 1370-LG40
20P-21AD045 45 36.8 25 1370-DBH70 500 4.5 330 111.11 1370-DC56 1370-LG52
20P-21AD052 52 42.5 30 1370-DBH71 500 3.5 385 142.86 1370-DC56 1370-LG52
20P-21AD073 73 59.6 40 1370-DBH72 500 2.6 345 192.31 1370-DC110 1370-LG92
20P-21AD086 86 70.3 50 1370-DBH73 500 2 345 250.00 1370-DC110 1370-LG92
20P-21AD100 100 81.7 60 1370-DBH74 500 2 345 250.00 1370-DC110 1370-LG110
20P-21AD129 129 105.4 75 1370-DBH75 500 1 270 500.00 1370-DC180 1370-LG140
20P-21AD167 167 136.4 100 1370-DBH76 500 0.7 280 714.29 1370-DC180 1370-LG180
20P-21AD207 207 169.1 125 1370-DBH77 500 0.7 280 714.29 1370-DC280 1370-LG228
20P-21AD250 250 204.3 150 1370-DBH78 500 0.5 365 1000.00 1370-DC280 1370-LG268
20P-21AD330 330 269.6 200 1370-DBH79 500 0.7 280 714.29 (5) (10)
(1) (6) (10)
20P-21AD412 412 336.6 250 500 0.808 7292 –
(2) (7) (10)
20P-21AD495 495 404.4 300 500 0.595 6069 –
(3) (8) (10)
20P-21AD667 667 544.9 400 500 0.542 6439 –
(1)
(2)
(3) HUBBELL_Y109W542GB - Must be sourced separately from drive.
(4)
Coil voltage = 115V AC, 50/60Hz.
(5)
(6) ABB_EHDB520C2P-1L - ABB contactor for drives with no dynamic brake. ABB_EHDB520C-1L - ABB contactor for drives with a dynamic brake. Must be sourced separately from drive.
(7)
(8)
(10)
DC Contactor Crimp Lug Kit Use the information provided in the table below to assist you in ordering the
Specifications correct Lug kit for your application.
Rated Motor Armature Conductor DB Conductor Size

Armature Current (1) DC Contactor Rating Size (2) (3) Armature Conductor DB Conductor Crimp Lug Kit Catalog
A DC A DC AWG AWG Crimp Lug Hole Size Lug Hole Size Number
4.1 - 35 56 8 8 #10 #10 1370-LG40
45 - 52 56 6 8 #10 #10 1370-LG52
55 56 4 8 #10 #10 1370-LG56
60 - 86 110 2 6 0.25 in. 0.25 in. 1370-LG92
100 - 110 110 1/0 4 0.25 in. 0.25 in. 1370-LG110
129 180 2/0 2 0.3125 in. 0.3125 in. 1370-LG140
146 180 3/0 2 0.3125 in. 0.3125 in. 1370-LG160
147 - 167 180 4/0 2 0.3125 in. 0.3125 in. 1370-LG180
207 - 218 280 300MCM 1/0 0.5 in. 0.375 in. 1370-LG228
250 - 265 280 400MCM 2/0 0.5 in. 0.375 in. 1370-LG268
(1)
The Rated Motor Armature Current is taken directly from the motor nameplate or motor data. The current listed in this column is the maximum current allowed for the Armature Conductor
Size (column 3) and the DC Contactor Rating (column 2).
(2)
The armature conductors are sized by multiplying the Rated Motor Armature Current by 1.25 as provided for in NEC 420-22 (1987). The DC lug ratings are determined from NEC Table 310-16
(1987) for copper conductors, insulation temperature rated at 75° C (167° F) at an ambient temperature of 30° C (86° F). If conditions are other than shown in NEC Table 310-16, then refer
to application codes.
(3)
The dynamic braking (DB) conductors are sized as in footnote 2 above, but at half ampacity due to the short time duration of current flow in these conductors, and has been sized to satisfy
NEMA Standard ICS 3-302.62 - Dynamic Braking. If the load inertia is larger than that of the motor, calculations must be made to determine correct conductor sizing and DB resistor wattage
per NEMA Standard ICS 3-302.62.

Notes:

Appendix B
HIM Overview
For information on . . See page For information on . . See page

External and Internal Connections B-1 Menu Structure B-3
LCD Display Elements B-1 Viewing and Editing Parameters B-5
ALT Functions B-2 Removing/Installing the HIM B-6
External and Internal The PowerFlex DC drive provides a number of cable connection points for
Connections the HIM (Frame A shown).
➊ ➍
PORT
MOD
NET A
NET B
STS
Front cover removed
➋
2
3ro
1
No. Connector Description

➊ DPI Port 1 HIM connection when installed in cover.
➋ DPI Port 2 Cable connection for handheld and remote options.
➌ DPI Port 3 or 2 Splitter cable connected to DPI Port 2 provides additional port.
➍ DPI Port 5 Cable connection for communications adapter.
LCD Display Elements

Display Description
F-> Power Loss Auto Direction⎥ Drive Status⎥ Alarm⎥ Auto/Man⎥ Information
0.0 RPM Commanded or Output Speed or Current
Main Menu:
Diagnostics
Parameter
Programming / Monitoring / Troubleshooting
Device Select
The top line of the HIM display can be configured with parameter 1321 [DPI Fdbk Select].

B-2 HIM Overview
ALT Functions To use an ALT function, press the ALT key, release it, then press the
programming key associated with the function printed on the HIM above
the key:
Table B.A ALT Key Functions
Press the ALT Key
and then … Performs this function …
S.M.A.R.T. Displays the S.M.A.R.T. list screen. See Using the S.M.A.R.T. List Screen
below for more information.
ALT Esc
View Allows the selection of how parameters will be viewed or detailed information
about a parameter or component.
Sel
Lang Displays the language selection screen (Not available on the PowerFlex DC
drive).
Auto / Man Switches between Auto and Manual Modes.
Remove Allows HIM removal without causing a fault if the HIM is not the last controlling
device and does not have Manual control of the drive.
Exp Allows value to be entered as an exponent

(Not available on the PowerFlex DC drive).
.
Param # Allows entry of a parameter number for viewing/editing.

+/–
Using the S.M.A.R.T. List Screen

During drive start up, most applications require changes to only a few
parameters. The LCD HIM provides the S.M.A.R.T. list screen which
contains the most commonly changed parameters, including the following:
Parameter Name / Number Description

[Max Ref Speed] (45) The nameplate base motor speed.
[Rated Motor Volt] (175) The maximum armature voltage of the drive output.
[Nom Mtr Arm Amps] (179) Corresponds to 100% of the current limit.
[Nom Mtr Fld Amps] (280) Rated motor nameplate field current.
[Anlg In1 Sel] (70) Selects the parameter to which a value will be written from
analog input 1 (default = “Speed Ref A”)
[Maximum Speed] (2) Defines the maximum speed of the drive.
[Current Limit] (7) Symmetrical current limit for both current directions for
four quadrant drives, expressed as a percentage of the
value in parameter 179 [Nom Mtr Arm Amps].
[Accel Time 1] (660) Sets the rate of acceleration for Ramp 0.
[Fdbk Device Type] (414) The source of speed feedback.
If your application requires additional parameter set up and tuning, refer to

Drive Start Up on page 2-1 for detailed instructions.

HIM Overview B-3
Menu Structure Figure B.1 HIM Menu Structure
User
Display
Esc Sel (See Key below for button descriptions.)
Faults Fault Info

Diagnostics Status Info Drive Status 1 View Fault Queue
Device Items Drive Status 2 Clear Faults
Device Version PowerFlex DC Drive Alarm 1 Clr Fault Queue
Product Data Spd Feedback Reset Device
Control Board Arm. Current
Main Control Bd Output Voltage
Boot Code Field Current
Main Control Bd AC Line Voltage
Application Code Output Power
Parameter Select via ALT Sel
Param Access Lvl Basic

File-Group-Par* FGP: File Advanced
Numbered List File 1 Name FGP: Group
Changed Params File 2 Name Group 1 Name FGP: Parameter
File 3 Name Group 2 Name Parameter Name
* default selection Group 3 Name Parameter Name
Parameter Name
PowerFlex DC
Device Select
(Connected DPI Devices) Value Screen
HIM CopyCat Device -> HIM

Memory Storage Reset To Defaults Device <- HIM
Delete HIM Set
Device Identity
Preferences Change Password
User Dspy Lines
Key:
Press to move between menu items
Press to select a menu item
Press Esc to move 1 level back in the menu structure
Press ALT Sel to select how to view parameters

B-4 HIM Overview
Diagnostics Menu
When a fault trips the drive, use this menu to access detailed data about the
drive.
Option Description
Faults View fault queue or fault information, clear faults or reset
drive.
Status Info View parameters that display status information about the
drive.
Device Items View statistics associated with DPI Communications.
Device Version View the firmware version and hardware series of
components.
Parameter Menu
Use this menu to view and edit parameters for the drive. When you enter the
the Parameter menu, by default the File–Group–Parameter view is displayed. To
access other views for the Parameter menu, with "Parameter" highlighted in
the Main menu, press Alt then Sel (View), select the desired view in the list
and press Enter. The following selections are available:
Option Description
Param Access Lvl Displays parameter 211 [Param Access Level]. The PowerFlex DC drive is
initially set to the Basic Parameter view. To view all parameters, set parameter
211 [Param Access Lvl] to option 1 “Advanced”.
File-Group-Par (FGP) Displays all parameters in a File - Group - Parameter structure. This simplifies
programming by grouping parameters that are used for similar functions.
Numbered List Displays all parameters in numerical order.
Changed Params Displays the most recently changed parameter. You can scroll through the list
of all changed parameters to the least recently changed. The new and default
values are listed for each parameter.
Refer to Viewing and Editing Parameters on page B-5 for more information.
Device Select Menu

Use this menu to access parameters in connected peripheral devices.
Memory Storage Menu

Drive data can be saved to, or recalled from, HIM sets.
HIM sets are files stored in permanent nonvolatile HIM memory.
Option Description
HIM CopyCat
Device -> HIM Save data to a HIM set.
Device <- HIM Load data from a HIM set to active drive memory.
Delete HIM Set Delete a HIM set.
Reset To Defaults Restore the drive to its factory default settings.

HIM Overview B-5
Preferences Menu
The HIM and drive have features that you can customize.
Option Description
Drive Identity Add text to identify the drive.
User Dspy Lines Select the display, parameter, scale and text for the User
Display. The User Display is two lines of user-defined data
that appears when the HIM is not being used for
programming.
Viewing and Editing LCD HIM

Parameters Step Key(s) Example Displays
1. In the Main Menu, press the Up Arrow or
Down Arrow to scroll to “Parameter.”
or
2. Press Enter. “FGP File” appears on the

FGP: File
top line and the first three files appear Monitor
below it. Motor Control
or Speed Command
3. Press the Up Arrow or Down Arrow to
scroll through the files. FGP: Group
Motor Data
4. Press Enter to select a file. The groups Field Config
Torq Attributes
in the file are displayed under it.
5. Repeat steps 3 and 4 to select a group FGP: Parameter

and then a parameter. The parameter Field Reg Enable
value screen will appear. Fld Economy En
Field Mode Sel
6. Press Enter to edit the parameter.

or FGP: Par 499
Fld Economy En
7. Press the Up Arrow or Down Arrow to Sel 1
change the value. If desired, press Sel Enabled
to move from digit to digit, letter to letter,
or bit to bit. The digit or bit that you can
change will be highlighted.
FGP: Par 499
Fld Economy En
8. Press Enter to save the value. If you 0
want to cancel a change, press Esc. or Disabled
Esc
9. Press the Up Arrow or Down Arrow to
scroll through the parameters in the
group, or press Esc to return to the
group list.
Numeric Keypad Shortcut

If using a HIM with a numeric keypad, press the ALT key and the +/– key to
access the parameter by typing its number.

B-6 HIM Overview
Removing/Installing the HIM The HIM can be removed or installed while the drive is powered.
Important: HIM removal is only permissible in Auto mode. If the HIM is
removed while in Manual mode or the HIM is the only
remaining control device, a fault will occur.
Step Key(s) Example Displays
To remove the HIM . . . ALT +
1. Press ALT and then Enter (Remove). Remove Op Intrfc:
The Remove HIM confirmation screen Press Enter to
appears. Disconnect Op Intrfc?
(Port 1 Control)
2. Press Enter to confirm that you want to
remove the HIM.
3. Remove the HIM from the drive.
To install HIM . . .
1. Insert into drive or connect cable.

Appendix C
Application Notes
For information on . . See page For information on . . See page
Analog Input Configuration C-1 Speed Feedback C-15
Current / Speed Curve C-4 Scale Blocks C-16
Droop Compensation C-5 Speed Regulation Functions C-17
Field Weakening Mode Configuration C-5 Start At Powerup C-24
(v1.006)
PID Function C-8 Fine Tuning the Regulators C-25
Reference Control C-13
Analog Input Configuration The analog inputs default to ±10V. To configure the analog inputs for
0-10V, set parameters [Anlg Inx Config] to 1, “0-10V”. To configure the
analog inputs for a current signal, set parameters [Anlg Inx Config] to 2, “0
- 20mA” or 3, “4 to 20mA”. In addition, switches S9, S10 and S11 must be
properly configured (refer to Table 1.L on page 1-33 for more information).
From Digital Reference

Setting
Anlg In1 Config
Analog Input 1 +/-10V Ain1 Tune Scale Anlg In1 Tune
1 0
Ref_1+
F
Anlg In1 Sel
1 Speed Ref A
HW + Volts
Anlg In1 Target
input Σ 0
2 type Anlg In1 Cmp Er
- 0
Ref_1-
Anlg In1 Scale
Window comparator
Anlg In 1 Filter
1 0 ms
Anlg In1 Cmp

Anlg In1 Offset 0
0
Anlg In1 Cmp Eq
Anlg In1 Cmp Dly

0 ms
Refer to the “Analog Inputs / Outputs & Mapping” block diagram on page D-4 for more information.
Example 1:
The speed reference value of a drive is defined with an external voltage of
5V. With this value the drive should reach the maximum allowable speed set
in Par 45 [Max Ref Speed]. Enter a scaling factor of 2 in [Anlg Inx Scale] to
scale the input voltage from 5V to 10V.

C-2 Application Notes
Example 2:
An external analog reference reaches a maximum value of 9.8V. Enter a
scaling factor of 1.020 in [Anlg Inx Scale] to scale the maximum voltage
from 9.8V to 10V.
The same result could be obtained via parameter [Anlgx Tune Scale], by
entering the values of the appropriate parameters via the HIM. The
maximum possible analog value (in this case 9.8V) would have to be
present at the terminal with a positive polarity.
Analog Input Signal Comparison

This feature provides an indication via the HIM or a digital output when the
signal of analog input 1 has reached a limit above or below a set reference
point.
Anlg In1 Cmp Err

0
Anlg In1 Cmp

0
Anlg In1 Cmp Eq
Anlg In1 Cmp Dly

0 ms
Calculations used to determine Pars1042 [Anlg In1 Cmp] and 1043 [Anlg
In1 Cmp Err]:
• [Anlg In1 Cmp] = (comparison value) x 10000 / (max. reference value)

• [Anlg In1 Cmp Err] = (tolerance value) x 10000 / (max. reference value)
Example 1:
An application requires an indication via a digital output that the motor

speed is within 100 RPMs of 700 RPM.
• Par 45 [Max Ref Speed] = 1500 RPM (maximum reference value)
• For Analog Input 1, 10V or 20mA sets the maximum value of Par 44
[Speed Ref A] = Par 45 [Max Ref Speed]

Application Notes C-3
Configure the following:
• Set Par 70 [Anlg In1 Sel] = “Speed Ref A”

• Set [Digital Outx Sel] = “Input1 Cmp” (Par 1045 [Anlg In1 Cmp Eq])
• Set Par 1042 [Anlg In1 Cmp] = 4667 (700 x 10000 / 1500)
• Set Par 1043 [Anlg In1 Cmp Err] = 666 (100 x 10000 / 1500 )
• Par 1045 [Anlg In1 Cmp Eq] = “1” (high) when the signal on Analog
Input 1 is within the range specified in Par 1043 [Anlg In1 Cmp Err]. Par
1045 [Anlg In1 Cmp Eq] = “0” (low) when the signal on Analog Input 1
is outside the range specified in Par 1043 [Anlg In1 Cmp Err].
Example 2:
An application requires an indication via a digital output that the output
current is within ±2% of 50% of the maximum current limit.
• Par 7 [Current Limit] = 100% (maximum reference value)
• For Analog Input 1, 10V or 20mA sets the maximum value = Par 7
[Current Limit]
Configure the following:
• Set Par 70 [Anlg In1 Sel] = “Pos Cur Lim”

• Set [Digital Outx Sel] = “Input1 Cmp” (Par 1045 [Anlg In1 Cmp Eq])
• Set Par 1042 [Anlg In1 Cmp] = 5000 (50 x 10000 / 100)
• Set Par 1043 [Anlg In1 Cmp Err] = 200 (2 x 10000 / 100 )

Current / Speed Curve The current/speed curve function allows you to establish a current limit
lower than the standard current limits of the drive (specified in parameters 8
[Current Lim Pos] and 9 [Current Lim Neg]) and reduce the output current
(torque) of the drive through a defined curve of five equally divided set
points as the speed increases based on a threshold speed, effectively
reducing torque.
Par 10 [Cur Lim Pos Out]

or
Par 11 [Cur Lim Neg Out]
Current/Speed
Par 751 [TrqTpr_Lim0]


Par 756 [TrqTpr_Spd]
• Enable the current/speed curve function by setting parameter 750

[TrqTpr_Enable] to 1 “Enabled”.
• Set the current limit (for both directions of rotation in four quadrant
drives) in parameter 751 [TrqTpr_Lim0]. The value specified in this
parameter overrides the value of parameters 8 [Current Lim Pos] and 9
[Current Lim Neg].
• Set the threshold speed at which current (torque) reduction begins in
parameter 756 [TrqTpr_Spd].
• Set the first reduced current limit in parameter 752 [TrqTpr_Lim1]. The
value defined in this parameter must be less than the value in parameter
751 [TrqTpr_Lim0] and greater than the values in parameters 753
[TrqTpr_Lim2], 754 [TrqTpr_Lim3] and 755 [TrqTpr_Lim4].
• Set the second, third and final reduced current limits in parameters 753
[TrqTpr_Lim2], 754 [TrqTpr_Lim3] and 755 [TrqTpr_Lim4],
respectively. The value of each subsequent parameter must be less than
the previous parameter’s value. The drive will maintain the value
specified in parameter 755 [TrqTpr_Lim4] up to the value set in
parameter 162 [Max Feedback Spd].

Droop Compensation The Droop function is used when the current must be balanced between two
drives. A typical situation is when two motors are mechanically coupled and
must run at the same speed. If, because of differences in the drive’s speed
regulators, one of the motors runs at a higher speed, it will be overloaded
and the second motor will function, essentially, as a brake.
The Droop function allows you to overcome this difference by adding a load
compensation component to the speed reference, which is proportional to
the actual load differences of the drives.
For Example:
Master Drive Slave Drive
[Anlg In1 Sel] = “Speed Ref A” [Anlg In1 Sel] = “Speed Ref A”
[Anlg Out1 Sel] = “Torque Ref” [Anlg In2 Sel] = “Load Comp”
[Enable Droop] = “Enabled”
[Droop Percent] = 5%
[Droop Filter] = 100 ms
[Droop Limit] = 1000
Field Weakening Mode Important: This configuration applies only to firmware version 1.006. For
Configuration (v1.006) instructions on configuring a drive with firmware version 2.001
for use with an AC or DC contactor, with or without a dynamic
brake, refer to Using Contactors on page 1-9.
The following configuration is required when operating the drive in field

weakening mode with a DC contactor and/or inverting fault device installed
in the armature circuit.
ATTENTION: The following information is merely a guide for

! proper installation. Rockwell Automation, Inc. cannot assume
responsibility for the compliance or the noncompliance to any
code, national, local or otherwise for the proper installation of
this drive or associated equipment. A hazard of personal injury
and/or equipment damage exists if codes are ignored during
installation.
When operating the PowerFlex DC drive in field weakening mode

(parameter 469 [Field Mode Sel] set to 1 - “Field Weaken”) and using a DC
contactor and/or an inverting fault device in the armature circuit, you must
complete the appropriate installation and programming requirements
detailed below.

Using a DC Contactor Only

1. Set parameter 1391 [ContactorControl] to "Contactor" (default value).
2. Set one [Relay Out x Sel] parameter and one [Digital Inx Sel] parameter
to "Contactor" (default value for parameters 1392 [Relay Out 1 Sel] and
140 [Digital In8 Sel]).
3. Connect the DC contactor auxiliary (status) contact to a second digital
input.
4. Set the corresponding second [Digital Inx Sel] parameter (133-144) to
"Fld Weak En".
5. Set the corresponding [Inversion In x] parameter (1276-1283 or
1387-1390) for the second digital input to "Enabled".
Using a DC Contactor and a Dynamic Brake

1. Set parameter 1391[ContactorControl] to "Contactor+DB".
2. Set one relay output parameter (1392 [Relay Out 1 Sel] or 629 [Relay
Out 2 Sel]) to "Contactor" and the other relay output parameter to
"ContactorDB".
3. Set one [Digital Inx Sel] parameter to "Contactor" (default value for
parameter 140 [Digital In8 Sel]).

input.

"Fld Weak En".

Using an Inverting Fault Device Only

1. Connect the inverting fault device contact to two separate digital inputs.
If using two inverting fault devices, the device contacts must be wired in
series.
2. Set one corresponding [Digital Inx Sel] parameter (133-144) to 35 - “Fld
Weak En”.
3. Set the other corresponding [Digital Inx Sel] parameter (133-144) to 14 -
"Aux Fault".
4. Set both of the corresponding [Inversion In x] parameters (1276-1283 or
1387-1390) to 1 - “Enabled”.

Using a DC Contactor and an Inverting Fault Device

DC Contactor Configuration
1. Set parameter 1391[ContactorControl] to "Contactor" (default value).
2. Set one [Relay Out x Sel] parameter and one [Digital Inx Sel] parameter
to "Contactor" (default value for parameters 1392 [Relay Out 1 Sel] and
140 [Digital In8 Sel]).
3. Connect the DC contactor auxiliary (status) contact to a digital input.
4. Set the corresponding [Digital Inx Sel] parameter (133-144) to 35 - “Fld

Weak En”.
1387-1390) to 1 - “Enabled”.
Inverting Fault Device Configuration

1. Connect the inverting fault device contact to a digital input.
2. Set the corresponding [Digital Inx Sel] parameter (133-144) to 14 - "Aux
Fault".
1387-1390) to 1 - “Enabled”.
Using a DC Contactor, a Dynamic Brake and an Inverting Fault Device

DC Contactor and Dynamic Brake Configuration
1. Set parameter 1391[ContactorControl] to "Contactor+DB".

2. Set one [Relay Out x Sel] parameter (1392 [Relay Out 1 Sel] or 629
[Relay Out 2 Sel]) to "Contactor" and the other relay output to
"ContactorDB".
3. Set one [Digital Inx Sel] parameter to "Contactor" (default value for
parameter 140 [Digital In8 Sel]).

input.

"Fld Weak En".

Inverting Fault Device Configuration

1. Connect the inverting fault device contact to a digital input.
2. Set the corresponding [Digital Inx Sel] parameter (133-144) to 14 - "Aux
Fault".
1387-1390) to 1 - “Enabled”.
ATTENTION: If a dynamic brake resistor is used with one of

! the configurations detailed above, dynamic braking stop time
will be extended when the digital input configured as 35 - “Fld
Weak En” is asserted. Equipment damage and/or personal injury
may result if one of these configurations is used in an
inappropriate application. Do not use one of these configurations
without considering applicable local, national and international
codes, standards, regulations or industry guidelines.
PID Function The PID function is used to increase or reduce the reference signal output to
the speed or current regulator of the drive. The PID function can be used for
nip-roll, winder/unwinder, roll doctor/salvage machine, pump and extruder
pressure control and extruder temperature control applications. (Refer to the
complete “PID Control” block diagram on page D-17.)
Examples are included below for configuring the following applications:

• Speed winder with a load cell and tension control
❏ Line speed signal (see Configure a Line Speed Signal on page C-9)
❏ Closed loop dancer / load cell feedback (see Configure the
Feedback Signal in the Follower Drive(s) on page C-10)
❏ Tension set point (see Configure the Tension Set Point Signal in the
Follower Drive(s) on page C-12)
• Torque winder with a load cell and tension control
❏ Line speed signal (see Configure a Line Speed Signal on page C-9)
❏ Closed loop dancer / load cell feedback (see Configure the
Feedback Signal in the Follower Drive(s) on page C-10)
❏ Tension set point (see Configure the Tension Set Point Signal in the
Follower Drive(s) on page C-12)

Configure a Line Speed Signal

The line speed signal is the main reference for the speed or current regulator
in the follower drive(s).
In the Master drive:
• Configure an analog output for the main speed reference (1 “Spd Ref
Out”)
In the Follower drive:
• Set Par 80 [Anlg In3 Sel] to 12 “UserDefined0”
• Set Par 786 [PID Source] to 8695 (503 + 8192). “503” = the parameter
number to which the signal from analog input 3 is sent (Par 503
[UserDefined0]), and “8192” is a drive internal fixed offset value.
Line Speed
Master NIP-Roll
Reverse
Forward
Load Cell
0 - +10V
M E M E
Tension Set
-10V
Master Slave
Drive Set Drive
Feedback
Line Speed Signal

(Internal Ramp)
+10V Forward
-10V Reverse
Line Speed Reference

In addition you can configure the following:
• Enter the gain for the feed-forward signal in Par 787 [PID Source Gain]
• Monitor the feed-forward signal after the gain is applied in Par 758 [Feed
Fwd PID]
P758
Feed Fwd PID
P786
Gain
PID Source
P787
PID Source Gain
Configure the Feedback Signal in the Follower Drive(s)

The feedback signal originates from a load cell or a closed loop dancer and
is input to the drive via an analog input (typically analog input 1, due to the
ability to filter this signal).
• Set Par 70 [Anlg In1 Sel] to 19 “PID Feedback”.
Line Speed
Master NIP-Roll
Reverse
Forward
Load Cell
0 - +10V
M E M E
Tension Set
-10V
Master Slave
Drive Set Drive
Feedback
Line Speed Signal

(Internal Ramp)
+10V Forward
-10V Reverse

In addition you can configure the following:
• Par 763 [PID Feedback] contains the raw feedback counts from the
analog input signal received from the transducer position (dancer) or
tension (load cell)
• Monitor the tension set point for a torque winder application in Par 1194
[Act Ten Ref Pct]
• Configure the PID feedback gain in Par 1254 [PID Error Gain]
• Limit the PID correction error using Par 757 [PID Clamp]
• Monitor the actual error input to the PI and PD blocks in Par 759 [PID
Error]
P760 P762
PID Setpoint 0 PID Setpoint Sel
P761
PID Setpoint 1
P1254 P763
PID Error Gain PID Feedback
+ +
+ +
P763
PID Feedback
+ Σ Σ
P1194 P757 P759

Act Ten Ref Pct PID Clamp PID Error

Configure the Tension Set Point Signal in the Follower Drive(s)

Configure the initial tension for the application in the Follower drive(s):
• Set Par 75 [Anlg In2 Sel] to 17 “PID Setpt 0”

Line Speed
Master NIP-Roll
Reverse
Forward
Load Cell
0 - +10V
M E M E
Tension Set
-10V
Master Slave
Drive Set Drive
Feedback
Line Speed Signal

(Internal Ramp)
+10V Forward
-10V Reverse
In addition, configure the following in the Follower drive(s):
• Verify that Par 762 [PID Setpoint Sel] is set to 0 “Setpoint 0”
P760 P762
P761
PID Setpoint 1
P1254 P763
PID Error Gain PID Feedback
+ +
+ +
P763
PID Feedback
+ Σ Σ
P1194 P757 P759

Act Ten Ref Pct PID Clamp PID Error

Reference Control The drive speed command can be obtained from a number of different
sources. The source is determined by drive programming and the condition
of the digital inputs configured as speed selects, a digital input configured
for “Auto/Manual” or Reference Select bits of a command word (see
Communication Configurations on page A-5 for more information).
“Auto” Speed Sources

The default auto source for a command reference (all speed select digital
inputs open or not programmed) is analog input 1 configured for “Speed
Ref A” (parameter 44 [Speed Ref A]). If any of the speed select digital
inputs are closed, the drive will use other parameters as the auto speed
command source.
“Manual” Speed Sources

The manual source for speed command to the drive is either the HIM
requesting manual control (see ALT Functions on page B-2) or the control
terminal block (analog input or MOP) if a digital input is programmed to
“Auto/Manual”.
Changing Speed Sources

The selection of the active speed reference can be made through the digital
inputs, DPI command, Jog button or Auto/Manual HIM operation.
Figure C.1 Speed Reference Selection Chart
[Digital Inx Sel]
Auto Reference Options Trim
Speed Sel: Ramp
Anlg In 1-3 Sel 3 2 1
DPI P1-5 Select P44 [Speed Ref A]
0 0 0
MOP Select
Encoder Out Sel P385 Ramp/
[Speed Ref Out] Speed
Anlg In 1-3 Sel Draw
DPI P1-5 Select P48 [Speed Ref B]
0 0 1
MOP Select Auto Trim
Encoder Out Sel
Speed /
P155 [Preset Speed 2] 0 1 0 Droop
P155 [Preset Speed 3] 0 1 1
P155 [Preset Speed 4] 1 0 0 Min
1 0 1 Ref Off Max
P155 [Preset Speed 5] Speed
Cmd Speed
P155 [Preset Speed 6] 1 1 0 Limit Limit
P155 [Preset Speed 7] 1 1 1
Speed
Manual Reference Options Command
Jog
HIM Requesting Manual Cmd
Man
P267 [TB Manual Ref]
Anlg In 1-3 Sel Speed
Digital Input
MOP Select Regulator
On
P266 [Jog Speed]
Speed
Feedback
Motor

Torque Reference Source

The torque reference can only be supplied by an analog input, the HIM, or a
network reference. Switching between available sources while the drive is
running is not available. Digital inputs programmed as “Speed Sel 1, 2, 3”
and the HIM Auto/Manual function (see above) do not affect the active
torque reference. The HIM, however, cannot acquire Manual Reference
control while it is configured to supply the torque reference.
Auto/Manual Examples
PLC = Auto, HIM = Manual
A process is run by a PLC when in Auto mode and requires manual control
from the HIM during set-up. The speed reference is issued by the PLC
through a communications module installed in the drive (Port 5). Therefore,
parameter 1327 [DPI P5 Select] is set to “Speed Ref A” with the drive
running from the Auto source.
Acquire Manual Control
• Press ALT then Auto/Man on the HIM. When the HIM acquires manual
control, the drive speed command comes from the HIM speed control
keys.
Release to Auto Control
• Press ALT then Auto/Man on the HIM again. When the HIM releases
manual control, the drive speed command returns to the PLC.
PLC = Auto, Terminal Block = Manual
A process is run by a PLC when in Auto mode and requires manual control
from an analog potentiometer wired to the drive terminal block. The auto
speed reference is issued by the PLC through a communications module
installed in the drive (Port 5). Therefore, parameter 1327 [DPI P5 Select] is
set to “Speed Ref A” with the drive running from the Auto source. Since the
Manual speed reference is issued by analog input 2, parameter 75 [Anlg in2
Sel] is set to “TB Man Ref”. The value of analog input 2 can be viewed in
parameter 267 [TB Manual Ref]. To switch between Auto and Manual,
parameter 136 [Digital In4 Sel] is set to “Auto/ Manual”.
Acquire Manual Control
• Close the digital input. With the input closed, the speed command comes
from the pot.
Release to Auto Control
• Open the digital input. With the input open, the speed command returns
to the PLC.

Auto/Manual Notes
1. Manual control is exclusive. If a HIM or Terminal Block takes manual

control, no other device can take manual control until the controlling
device releases control.
2. If a HIM has manual control and power is removed from the drive, the
drive will return to Auto mode when power is reapplied.
Speed Feedback The value of parameters 169 [Encoder PPR] and 162 [Max Feedback Spd]
must be inside the allowed area shown in the figure below regardless of the
value selected in Par 414 [Fdbk Device Type].
10000
6000
5000
4000
3000
All
ow
2000
ed
Ar
1000
ea
900
800
700
600
500
400
300
200
100 900
100 200 300 400 500 600 700 800 1000 2000 3000 4000
Par 169 [Encoder PPR]

Scale Blocks The Scale Blocks function allows you to link or rescale dissimilar parameter
types (e.g., integer vs. real) though multiply, divide, maximum and
minimum limits, input and output offsets and absolute value functions.
There are six individually configurable Scale Blocks. A representative block
diagram is shown below.
Important: The Scale Blocks functions are executed sequentially in the

background, which can cause a delay in processing data
between the input and output values. The amount of delay is
dependant on the application.
The following rules apply to Scale Blocks:
• All input [Scalex Input] and output [Scalex Output] values are specified
as a parameter number (not parameter values).
• Both Sink (read/write) and Source (read only) parameters can be used as
input values ([Scalex Input]).
• Only Sink (read/write) parameters can be used as the output value
([Scalex Output]).
• Configuration parameters (parameters that can only be changed while
the drive is stopped) can be used as the output value ([Scalex Output]).
However, any value written to a configuration parameter will not take
effect in the drive until it is stopped.
• The output value is truncated to a whole number when different
parameter types are used (e.g., a real input value of 54.97% becomes an
integer output value of 54 RPM).
• Dividing by zero (0) does not cause an error, but will result in an output
value of zero (0).
• Turning off (setting = “0”) the input parameter or changing the output
parameter number does not reset or change the original output value (i.e.,
the output parameter remains at the last value written).
Scale Block 1 P488

Scale1 In Max
+ +
P484
Scale1 Input Σ X Σ P485
Scale1 Output
+ +
P491
P492 P489 Scale1 Out Off
Scale1 In Abs Scale1 In Min
P487
Scale1 Div
P490 P486
Scale1 In Off Scale1 Mul

Linking Parameters Via the Scale Block Parameters

Most parameter values are entered directly by the user. However, certain
parameters can be “linked,” via the Scale Block parameters, so the value of
one parameter becomes the value of another.
For example, the value of an analog input 1, parameter 70 [Anlg In1 Sel],
can be linked to parameter 660 [Accel Time 1]. In order to do so:
• Set parameter 70 [Anlg In1 Sel] to 12 “UserDefined0”.
• Set parameter 484 [Scale1 Input] to “503” (the parameter number of

[UserDefined0]).
• Set parameter 485 [Scale1 Output] to “660” (the parameter number of

[Accel Time 1]).
In this way, rather than entering an acceleration time directly (via HIM), the
link allows the value to change by varying the analog signal. This can
provide additional flexibility for certain applications. This functionality
should be tested for the desired response before applying to an application.
Speed Regulation Functions The PowerFlex DC Digital drive provides a flexible speed regulator circuit
that can be adapted to the requirements of a variety of applications. The
drive is set to PI regulation by default.
Adaptive Speed Regulator

The adaptive speed regulator function enables different gains of the speed
regulator depending on the speed reference or another variable (adaptive
reference). This allows optimum adaptation of the speed regulator to the
specific application.
P186 P187
Adaptive Joint 1 Adaptive Joint 2
P188 P189
Adaptive P Gain1 Adaptive I Gain1
P190 P191
P192 P193
P183
Adaptive Ref
P184 P185
Adaptive Spd 1 Adaptive Spd 2

The adaptive speed regulator is enabled with parameter 181 [Adaptive Spd
En] = “1 Enabled”. Normally the gain depends on the speed of the drive. It
can, however, vary according to a variable defined in parameter 183 [Adap
Ref]. The type of regulation used is selected in parameter 182 [Adaptive
Reg Typ]; 0 = “Speed”, or 1 = “Adaptive Ref”.
Parameters 184 [Adaptive Spd 1] and 185 [Adaptive Spd 2] are used to
define the three ranges that may have different gains. A parameter set can be
defined for each of these ranges, with each set containing an individually
definable P and I component (i.e., Pars 188 [Adaptive P Gain1] and 189
[Adaptive I Gain1], 190 [Adaptive P Gain2] and 191 [Adaptive I Gain2],
and 192 [Adaptive P Gain3] and 193 [Adaptive I Gain3]). When the
adaptive speed regulator is enabled, the first set of parameters is active until
the speed specified in Par 184 [Adaptive Spd 1] or Par 183 [Adap Ref] is
reached.
Parameters 186 [Adaptive Joint 1] and 187 [Adaptive Joint 2] ensure a

smooth transition between the different parameter sets. The fields must be
defined so that [Adaptive Joint 1] and [Adaptive Joint 2] do not overlap.
When the adaptive speed regulator is enabled, parameters 87 [Spd Reg Kp]
and [Spd Reg Ki] parameters have no effect on the speed regulator. They do,
however, retain their value and are active when the adaptive speed regulator
is disabled.
Configuring the Adaptive Speed Regulator
• Set Par 181 [Adaptive Spd En] = “1 Enabled”
• If the gain must be changed on the basis of units other than the drive’s
speed reference, set Par 182 [Adaptive Reg Typ] = 1 “Adaptive Ref”. The
adaptive reference is provided to the drive as an analog value via an
analog input. For this reason Par 183 [Adaptive Ref] must be assigned to
an analog input. The other possibility is to enter the value of Par 183
[Adaptive Ref] via the HIM. In this case the an analog input is not
necessary.
• Enter the appropriate values in Par 184 [Adaptive Spd 1] and Par 185
[Adaptive Spd 2] to define the three speed ranges. Values are expressed
as a percentage of Par 45 [Max Ref Speed] and the maximum value of
Par 183 [Adaptive Ref].
• When Par 182 [Adaptive Reg Typ] = 0 “Speed”, tuning is completed via
Fine Tuning the Regulators on page C-25. In this case the following
points must be taken into consideration:
❏ The value entered in Par 61 [TstGen Offset] must be at the low end
of the speed range to be tuned, but is also outside the range set in
Par [Adaptive Joint x].

❏ Enter the step value in Par 60 [TstGen Amplitude], so that the speed
remains inside the range to be tuned.
❏ The optimization is carried out separately for each range and the
parameters of the regulator are set for each range with Pars
[Adaptive P Gainx] and [Adaptive I Gainx].
❏ After the optimization of the different phases review the entire
speed range. By changing the value of [Adaptive Joint x] it is
possible to reduce the instabilities present in the transients during
the changes from one range to the other. Increasing the values
transients are slighter.
• When Par 182 [Adaptive Reg Typ] = 1 “Adaptive Ref”, tuning is

application specific.
• When the speed zero logic (see page C-22) is disabled (factory default
setting) and the drive is disabled, the gains of the speed regulator are
active. These are set via Pars 188 [Adaptive P Gain1] and 189 [Adaptive
I Gain1]. When the speed zero logic is enabled, the values set when the
motor is stopped are valid.

Speed Up Function
The Speed-up function is used to avoid oscillations in the presence of loads
with a high moment of inertia. When this function is enabled (default value
of 0 “Speed Up” in Par 1016 [SpdFuncSelect]), a D (derivative) value is
added to the speed feedback circuit, which allows you to increase the
integral gain of the speed regulator. It is also useful in the case of cyclical
non-constant loads on the motor (e.g., cams). The feedback applied to the
speed regulator is made of two components:
• the motor speed
• the output signal from the Speed Up function
Figure C.2 Speed-Up function inactive Figure C.3 Speed-up function active
Oscillation during a speed change due to a high moment of The same drive with Speed-up function active.
inertia. Top: Par 122 [Spd Feedback]
Top: Par 122 [Spd Feedback] Bottom: Par 199 [Arm Current Pct]
Bottom: Par 199 [Arm Current Pct]
Parameters used in the example:
• Par 445 [Speed Up Gain Pct] = 50 %
• Par 446 [Speed Up Base] = 14 rpm/ms
• Par 447 [Speed Up Filter] = 20 ms
Speed Threshold Indicators

There are two speed threshold functions available that can be programmed
via a digital output to provide indication of when the drive has exceeded
certain set points.
Par 393 [Speed Threshold] displays whether the speed of the drive is above
or below a set speed for clockwise and counter-clockwise rotation. Set the
threshold speed for clockwise rotation in Par 101 [Spd Thresh Pos] and set

the threshold speed for counter-clockwise rotation in Par 102 [Speed Thresh
Neg]. You can specify a delay time before indication that the speed has
fallen below the threshold values in Par 103 [Threshold Delay]. Par 393
[Speed Threshold] can be assigned to a digital output. A digital output so
assigned will only change state at the clockwise (positive) speed threshold.
P101
Speed Thresh Pos
[Digital Outx Sel]

= 2 “Spd Thresh”
P122
Spd Feedback
P393
Speed Threshold
P102
Speed Thresh Neg
P103 0 t
Threshold Delay
Par 394 [At Speed] indicates whether or not the speed of the drive
corresponds to the set speed reference (specified in Par 118 [Speed Reg In])
before the speed regulator and the ramp reference (if enabled) are applied.
The speed above and below the speed reference at which indication will
occur is set in Par 104 [At Speed Error]. You can specify a delay time before
indication that the speed reference is within the range set in Par 104 [At
Speed Error] will occur using Par 105 [At Speed Delay]. Par 394 [At Speed]
can be assigned to a digital output.
P118
Speed Reg In P104
At Speed Error
[Digital Outx Sel]

= 3 “At Speed”
P122
Spd Feedback P394
At Speed
P105 0 t
At Speed Delay

Speed Zero Function

The Speed Zero Logic determines the behavior of the drive when the motor
is at zero speed. Refer to the Speed Adaptive and Speed Zero Logic block
diagram on page D-12.
Configuring the Speed Zero Logic
It is possible to avoid drive creep when the motor is at zero speed by

disabling the Integral section of the Speed regulator. By default, the output
of the Integral portion of the Speed regulator is disabled (Par 123 [Spd Zero
I En] = 0 “Disabled”).
Important: If the speed regulator is disabled, the motor cannot receive a

load when it is stopped. Therefore this function is not suitable
for all applications!
Disable the output of the P gain of the Speed regulator by setting Par 126
[Spd Zero P Gain] to one of the following settings:
• If the speed reference is above the value set in Par 106 [Ref Zero Level]:
Set Par 124 [Spd Ref Zero En] = 1 “Enabled”
• If the speed reference and/or the reaction are above the value set in Par
106 [Ref Zero Level], set Par 124 [Spd Ref Zero En] = 0 “Disabled”
Par 124 [Spd Ref Zero En] is active only when Par 125 [Spd Zero P En] = 1
“Enabled”.
Set the P gain for zero speed:
• If the P gain corresponds to the value set in Par 126 [Spd Zero P Gain],
then set Par 125 [Spd Zero P En] = 1 “Enabled”
• If the P gain corresponds to the normal P gain, then set Par 125 [Spd
Zero P En] = 0 “Disabled”
The P gain at zero speed is set via Par 126 [Spd Zero P Gain] when Par 125
[Spd Zero P En] = 1 “Enabled”.
The threshold for the recognition of zero speed is determined by the value in
Par 106 [Ref Zero Level].

Speed Draw Function

The Speed Draw function can be used to apply a configurable speed ratio
(set in Par 1017 [Speed Ratio]) to the main speed reference of the drive.
This function is useful in a multi-drive system where a proportional speed
increase between the motors is required. The range of parameter 1017
[Speed Ratio] can be set between 0 and 32767 if written in digital form, or
can be set from 0 to 20000 (0 to +10V) if assigned via an analog input. The
resulting speed value can be viewed in Par 1018 [Speed Draw Out] via an
analog output.
Figure C.4 Speed Draw Example
Master = 1000 RPM 1050 RPM 1100 RPM
M M M
Drive A Drive B Drive C
Anlg Input Anlg Input Anlg Input

1 1 2 1 2
Line Speed Line Speed

ratio 1 = +5% ratio 2 = +10%
+ +
Speed Ratio = 5.25V Speed Ratio = 5.5V
(10500 count) (11000 count)
+
Line Speed
Speed Draw Example Configuration
Drive A:
• Set parameter 70 [Anlg In1 Sel] to 4 “Trim Speed”

Drive B:
• Set parameter 75 [Anlg In2 Sel] to 22 “Speed Ratio”
• Set parameter 1017 [Speed Ratio] to 10500
Drive C:
• Set parameter 75 [Anlg In2 Sel] to 22 “Speed Ratio”
• Set parameter 1017 [Speed Ratio] to 11000

Start At Powerup The “Start At Powerup” function allows you to automatically resume
running at commanded speed after drive input power is restored, a run
command is issued and all of the start permissive conditions indicated in the
diagram below are met. To enable this feature, parameter 1344 [Start At
Powerup] must be set to 1 “Enable”.
ATTENTION: Equipment damage and/or personal injury may

! result if this parameter is used in an inappropriate application. Do
not use this function without considering applicable local,
national and international codes, standards, regulations or
industry guidelines.
In addition, A delay time of up to 10800 seconds (3 hours) can be

programmed in parameter 1345 [Powerup Delay]. An automatic drive
restart is not possible before the delay time has expired. If a “Start”, “Run”
or “Stop” command is asserted before the time in this parameter expires, the
“Start At Powerup” function will be aborted.
Start At PowerUp
[Powerup Delay] No
Time Expired?
Yes
All Start Permissives Met?

1. No fault conditions are present.
2. No Type 2 alarm conditions are No
present.
3. The terminal block programmed
enable input is closed.
4. All Stop inputs are maintained.
Yes
Is the terminal block Run, No

Run Forward or Run Reverse
Input Closed?
Yes
Powerup Start Powerup Terminated!

Normal Mode
During the time specified in parameter 1345 [Powerup Delay], the alarm
indicator “ ” is displayed on the HIM and bit 12 “PwrUp Start” of
parameter 380 [Drive Status 1] is set to “1”.

Fine Tuning the Regulators The PowerFlex DC drive control regulators have predefined values meant to
provide consistent drive performance without performing any further
configuration, with the exception of the armature current regulator, which
must always be tuned. When the armature current regulator has been tuned
to meet the requirements of the application, the fine tuning procedures for
the other regulators are not necessary. However, the fine tuning procedures
can be used to optimize the output and control features of the drive.
The drive contains the following regulation circuits:

• Armature current regulator - The auto tuning procedure is run via Par
452 [CurrReg Autotune]. Refer to Chapter 2 - Drive Start Up.
• Field current regulator:
❏ A manual procedure to adjust the armature inductance when the

autotune steps yielded a value outside the recommended setting.
Refer to Manually Adjusting the Current Regulator Tune
Settings on page C-26.
❏ A fine tuning procedure is available below. Refer to Fine Tuning the

Field Current Regulator on page C-26.
• Speed regulator - A fine tuning procedure is available below. Refer to

Fine Tuning the Speed Regulator on page C-29.
• Armature voltage regulator - A fine tuning procedure is available below.

Refer to Fine Tuning the Voltage Regulator in the Field Converter on
page C-31.
The fine tuning procedures are included below. In order to obtain a step
function, the internal “Test generator” is used. The goal of the fine tuning
procedures is to obtain an optimal step response. For example, it is
recommended that you directly measure the step response for the field
current regulator.
The analog output can be connected to the terminal strip, with a sampling
rate of two milliseconds.
Using the Test Generator
The “Test Generator” function creates signals with a rectangular wave form
based on a specific frequency and amplitude. The frequency and amplitude
can be added to a configurable offset value, if needed. Par 58 [TstGen
Output] determines which regulator input signal (reference) is active; torque
current, field, ramp, or speed.

Manually Adjusting the Current Regulator Tune Settings

During the current regulator auto tuning test the value of Par 587 [I Reg
Error] displays. This parameter is used to determine whether the current
regulator is correctly tuned. The value should be as near to zero as possible,
but values between -40 and +40 are acceptable. Any changes to the resulting
value are made in Par 454 [Arm Inductance] in order to fine tune the speed
regulator and set Par 587 [I Reg Error] to an acceptable value.
❏ If the value of Par 587 [I Reg Error] is positive, increase the value
of Par 454 [Arm Inductance].
❏ If the value of Par 587 [I Reg Error] is negative, decrease the value
of Par 454 [Arm Inductance].
Fine Tuning the Field Current Regulator

Important: In most cases motors with a direct current and an independent
excitation work with a constant field (Par 469 [Field Mode Sel]
= 0 “Base Speed”). In this case it is not necessary to optimize
the field current or armature voltage regulators.
The procedure below is used for drives that use constant torque and power
(mixed armature and field regulation). In these cases it is necessary to
configure the field converter according to this method.
Important: Do not issue a “Start” command to the drive during the field
current regulator fine tuning procedure.
Follow the procedure below to fine tune and optimize the field current
regulator:
1. Configure the following parameters:
❏ Set Par 467 [Max Fld Curr Pct] = 100% of the field rated current of
the connected motor
❏ Set Par 468 [Min Fld Curr Pct] = 0
❏ Set Par 91 [Fld Reg Kp] = 0.00
❏ Set Par 92 [Fld Reg Ki] = 0.00
2. Measure the field current using an analog output by setting:
❏ Par 66 [Anlg Out1 Sel] = 18 “Fld Current”

❏ Par 67 [Anlg Out2 Sel] = 24 “Field Ref”

❏ Set Par 497 [Field Reg Enable] = 1 “Enabled” (default)

❏ Set Par 469 [Field Mode Sel] = 1 “Field Weaken”
❏ Set Par 498 [Force Min Field] = 1 “Enabled”
4. Configure the following Test Generator parameters:
❏ Set Par 58 [TstGen Output] = 3 “Field Ref”
❏ Set Par 60 [TstGen Amplitude] = 70% of the field rated current of

the motor (this setting allows the system overshoot).
5. Increase the value of the Par 91 [Fld Reg Kp] until the overshoot of the field
current (displayed in Par 234 [Fld Current Pct]) is lower than 4%.
6. Increase the value of Par 92 [Fld Reg Ki] until the overshoot is higher than 4%.
Then, decrease the value of this parameter until it becomes slightly lower than
4%.
Important: Because of the relatively high field time constant, the rising
speed of the field current is limited. The rising time with
optimal tuning conditions could be up to 100 milliseconds.
7. Set Par 58 [TstGen Output] = 0 “NotConnected”.
8. Set Par 498 [Force Min Field] = 0 “Disabled”.
9. Set Par 468 [Min Fld Curr Pct] to the desired value.
10. Configure the analog outputs according to your application needs.

Field Current Regulator Tuning Examples
Figure C.5 Increase in the field current with oscillation Figure C.7 Increase in the field current without
Non-optimal response of the regulator. oscillation
Top: Par 500 [Field Ref Pct] This graph, as compared to the graph in Figure C.5, shows an
Bottom: Par 234 [Fld Current Pct] increase in [Fld Reg Kp] from 2% to 10% with [Fld Reg Ki] = 5%.
Top: Par 500 [Field Ref Pct]
Bottom: Par 234 [Fld Current Pct]
Figure C.6 Too high of a time constant on the field

The reduction of the field current depends on the field time
constant. Therefore, the regulator has no influence on the flux
current.
Top: Par 500 [Field Ref Pct]
Bottom: Par 234 [Fld Current Pct]

Fine Tuning the Speed Regulator

Follow the procedure below to fine tune and optimize the speed regulator:
❏ Set Par 58 [TstGen Output] = 4 “Ramp Ref”
❏ Set Par 59 [TstGen Frequency] = 0.2 Hz
❏ Set Par 60 [TstGen Amplitude] = 10 %
❏ Set Par 61 [TstGen Offset] = 20 %
2. Measure the results on analog outputs 1 and 2 by setting:

❏ Par 66 [Anlg Out1 Sel] = 8 “Spd Reg Out”
❏ Par 67 [Anlg Out2 Sel] = 13 “Motor Curr”.
3. Set Par 660 [Accel Time 1] = 0 sec.
4. Set Par 662 [Decel Time 1] = 0 sec.
5. Set Par 87 [Spd Reg Kp] = 0.00
6. 88 [Spd Reg Ki] = 0.00
7. Start the drive.
8. Increase the value of Par 87 [Spd Reg Kp] until the overshoot is lower than 4%
with the shortest possible acceleration or deceleration time.
9. Increase the value of Par 88 [Spd Reg Ki] until the overshoot is higher than 4%.
Then, decrease the value of this parameter until its value becomes slightly
lower than 4%.
10. Stop the drive.
Important: When the “Bypass” function is enabled (Par 458 [SpdReg FB

Bypass] = 1 “Enabled”) the drive is automatically switched to
armature feedback when a “Speed fbk loss” fault occurs due to
an encoder or tachometer feedback loss. In this case, you must
repeat steps 1 - 9 of the “Fine Tuning the Speed Regulator”
procedure when the fault has been cleared. After an automatic
switch to armature feedback, the speed regulator works with
Pars 459 [SpdReg Kp Bypass] and 460 [SpdReg Ki Bypass]
and the D (derivative) part of the speed regulator is
automatically excluded.
When it is necessary to have different gains for the speed regulator above
the speed range, you can utilize the adaptive speed regulator. For further
information about this function refer to the Adaptive Speed Regulator block
diagram page C-17.

[Spd Reg Kp] and [Spd Reg Ki] curves
Figure C.8 [Spd Reg Kp] too low Figure C.10 [Spd Reg Ki] too high
Top: Par 122 [Spd Feedback] Top: Par 122 [Spd Feedback]
Bottom: Par 199 [Arm Current Pct] Bottom: Par 199 [Arm Current Pct]
20.00 ms/DIV 20.00 ms/DIV
Figure C.9 [Spd Reg Kp] too high Figure C.11 [Spd Reg Ki] correct
Top: Par 122 [Spd Feedback] Top: Par 122 [Spd Feedback]
Bottom: Par 199 [Arm Current Pct] Bottom: Par 199 [Arm Current Pct]
20.00 ms/DIV 20.00 ms/DIV

Fine Tuning the Voltage Regulator in the Field Converter

Important: In most cases, DC motors with independent excitation, work
with a constant field (Par 469 [Field Mode Sel] = 0 “Base
Speed”). In this case it is not necessary to optimize the
regulator of the field current and the regulator of the armature
voltage.
When field weakening occurs, the voltage regulator keeps the armature
voltage at a constant level. The critical point for this regulator is at the
beginning of field weakening, because with the saturation of the motor field
the system requires more consistent changes in the field current in order to
carry out a flux change. Tune the regulator so that the armature voltage
undergoes very small changes.
Important: Before the optimization of the voltage regulator, the speed and
field current regulators must have already been tuned. Refer to
Tune the Current Regulator: on page 2-10 and Fine Tuning the
Field Current Regulator on page C-26.
❏ Set Par 58 [TstGen Output] = 4 “Ramp Ref”
❏ Set Par 59 [TstGen Frequency] = 0.2 Hz
❏ Set Par 60 [TstGen Amplitude] = 10 %
❏ Set Par 61 [TstGen Offset] = to the switching point from the

armature to the field regulation. For example: If Par 162 [Max
Feedback Spd] = 2000 rpm, field weakening starts at 1500 rpm.
Therefore, set Par 61 [TstGen Offset] = 75 %.
2. Measure the field current and the armature voltage using analog outputs 1 and
2, by setting:
❏ Par 66 [Anlg Out1 Sel] = 18 “Fld Current”

❏ Par 67 [Anlg Out2 Sel] = 14 “Motor Volts”
3. Start the drive.
4. Check the armature voltage via analog output 2. After a possible short
oscillation, the voltage should remain constant. Refer to the Field Voltage
Regulator examples below. You can change the Proportional and Integral gains
of the Field Voltage regulator via Pars 493 [Arm Volt Kp] and 494 [Arm Volt Ki].
5. Stop the drive.

Field Voltage Regulator Tuning Examples
Figure C.12 Field voltage oscillation Figure C.14 Optimal field regulation
Oscillation after a speed change where [Arm Volt Kp] = 10% and After a short transient, the field current and armature voltage are
[Arm Volt Ki] = 80%. constant. [Arm Volt Kp] = 40%, [Arm Volt Ki] = 5%.
Top: Par 234 [Fld Current Pct] Top: Par 234 [Fld Current Pct]
Bottom: Par 233 [Output Voltage] Bottom: Par 233 [Output Voltage]
Figure C.13 Too small of a gain

The armature voltage increases where [Arm Volt Kp] = 3% and
[Arm Volt Ki] = 5%.
Top: Par 234 [Fld Current Pct]
Bottom: Par 233 [Output Voltage]

Tuning the Field Current Curve

The function of the field current curve is to control the actual motor flux
and, subsequently, motor torque if the field goes into an overvoltage
condition. Figure C.15 below illustrates the relationship between flux and
flux current when the field current curve is defined versus not defined.
Important: Complete the procedures in the order listed below when tuning
the field current curve:
•Field current regulator. Refer to Fine Tuning the Field Current

Regulator on page C-26.
•Field current curve tuning (Flux / if curve)

•Voltage regulator in the field converter. Refer to Fine Tuning
the Voltage Regulator in the Field Converter on page C-31.
Figure C.15 Curve Conversion Flux/Current
Par 234 [Fld Current Pct]
Par 280 [Nom Mtr Fld Amps] @ 100%
Par 916 [Fld Const 90 Pct]

Curve A
Par 280 [Nom Mtr Fld Amps] @ 50%
Curve B
40% 50% 70% 90% 100%

Par 500 [Field Ref Pct]
Examples:
• Curve A - If the default settings of the drive are retained, the flux current
to flux reference will remain linear when the value of Par 500 [Field Ref
Pct] changes. E.g.,
o If Par 467 [Max Fld Curr Pct] / Par 500 [Field Ref Pct] = 100%,
then Par 234 [Fld Current Pct] / Par 500 [Field Ref Pct] = Par 280
[Nom Mtr Fld Amps]
o If Par 467 [Max Fld Curr Pct] / Par 500 [Field Ref Pct] = 50%, then
Par 234 [Fld Current Pct] / Par 500 [Field Ref Pct] = 50% of Par
280 [Nom Mtr Fld Amps]
• Curve B - If the field current curve fine tuning procedure is completed,

the flux current to flux reference curve will follow a curve determined by
the real flux percentage of Par 500 [Field Ref Pct] necessary to
determine the circulation of the field current for the connected system.
Refer to the Current Regulator block diagram on page D-13.

Field Current Curve Tuning Procedure:
1. Reset the field current curve by setting Par 920 [Reset Fld Curve] to “1”.
❏ Enter the percentage (100%) of the maximum motor nameplate

rated armature voltage in Par 921 [Out Volt Level]
❏ Set Par 469 [Field Mode Sel] = 0 “Base Speed”
❏ Set Par 467 [Max Fld Curr Pct] = 100%
3. Start the drive.
4. Increase the motor speed until the value (electromotive force) displayed in Par
233 [Output Voltage] corresponds to the value previously set in Par 175 [Rated
Motor Volt].
5. Decrease the value of Par 467 [Max Fld Curr Pct] until the value displayed in
Par 233 [Output Voltage] is equal to 90% of Par 175 [Rated Motor Volt]. When
you have reached this value, read the value displayed in Par 234 [Fld Current
Pct] and enter the value into Par 918 [Fld Const 90 Pct].
8. Stop the drive.
9. Set the desired method of field control in Par 469 [Field Mode Sel] (0 “Base
Speed” or 1 “Field Weaken”)
10. Reset the value of 467 [Max Fld Curr Pct] to 100%.
If you change the value of Par 175 [Rated Motor Volt] or par 280 [Nom Mtr
Fld Amps], the field current curve will need to be re-tuned.

Appendix D
Control Block Diagrams
For information on . . See page . .

PowerFlex DC Drive Overview D-2
Digital Inputs/Outputs & Mapping Standard and I/O Expansion Card D-3
Analog Inputs/Outputs and Mapping D-4
Speed Reference Selection D-5
Speed Reference Generation D-6
Ramp Reference Block D-7
Speed / Torque Regulator D-8
Droop Compensation - Inertia / Loss Compensation D-9
Speed Feedback D-10
Speed Regulator PI Block D-11
Speed Adaptive and Speed Zero Logic D-12
Current Regulator D-13
Field Current Regulator D-14
Motor Parameters D-15
Speed Threshold / Speed Control D-16
PID Control D-17
Scale Blocks D-18
User Defined Variables D-19
Taper Current Limits D-20
Unit Scaling D-21
Test Generator D-22
Speed Reference Selection D-23
Fault / Alarm Mapping D-24
Diagram Conventions
Examples:
PXXX
ParName
PXXX
ParName
= Read / Write Parameter
= Read Only Parameter
PXXX = Parameter Number

ParName = Parameter Name

D-2
BASIC CONFIGURATION
P45 P162
PowerFlex DC Drive Overview Max Ref Speed Max Feedback Spd
P175 P179
Rated Motor Volt Nom Mtr Arm Amps
P280 P374
Nom Mtr Fld Amps Drv Fld Brdg Cur
P2 P414
Maximum Speed Fdbk Device Type
P660 P662
Drive Reference, Feedback and Status Accel Time 1 Decel Time 1
P44 P110 P118 P588 P466

Speed Ref A Ramp In Speed Reg In AC Line Freq AC Line Voltage
P48 P113 P41 P233 P351 Input / Output Fault / Alarm

Speed Ref B Ramp Out Current Reg In Output Voltage Field Current Mapping Mapping
P385 P1018 P122 P200 P1052 Functions

Speed Ref Out Speed Draw Out Spd Feedback Arm Current Output Power
P372 P346 P393 P395 P381
Spd Limit Active Torque Positive Speed Threshold At Zero Speed Drive Status 1
0 0 Above Threshold (0) Equal (0) 0000111000001101
PowerFlex DC Drive Overview
1 1 Below Threshold (1) Not Equal (1)

P349 P347 P651 P394 P1403
CurrLimit Active Torque Negative Encoder State At Speed Start Inhibits

0 0 Fault (0) Not Equal (0) xx00000000000000
1 1 OK (1) Equal (1)
P199
Arm Current Pct
Reference Ramp Speed / Current Regulator
P924
Select Actual Speed
P110 P113 P118 Speed Regulator Current Regulator
Analog In 1-3 Ramp In Ramp Out Speed Reg In
Reference
DPI Port 1-5 Motor Control
Generation P122
MOP
Spd Feedback
Speed Feedback
Digital Inputs Status
Terminal Block 2 Terminal Block 4 Expansion I/O P41
Current Reg In
P565 P569 P573
Dig In Term 1 Dig In Term 5 Dig In Term 9
P351
Field Current
P566 P570 P574 Field Control

C1 D1
P500
Field Ref Pct
P567 P571 P575
P568 P572 P576 P280

Dig In Term 4 Dig In Term 8 Dig In Term 12 Nom Mtr Fld Amps
P374
Drv Fld Brdg Cur
Digital Inputs Digital Inputs/Outputs Digital Outputs

Standard and Expansion I/O
P1267 26
12
P145 Inversion out 1
* P1276
DG1+ Inversion In 1
D01
P133 30
Digital Out1 Sel F
F +24V DC
16 Digital In1 Sel Drive Relay Outputs
DG1-
P1268 27
13 P1392 P1393 35 Inversion out 2
Relay Out 1 Sel Inversion Relay 1 P146
* P1277 D02
DG2+ Inversion In 2 R1NO 30
P134 36 F
F Digital Out2 Sel
+24V DC
F R1COM
16 Digital In2 Sel
DG2- P1269 28
14 P147 Inversion out 3
D03
* P1278 75 30
DG3+ P629 P1275 F
Inversion In 3 Digital Out3 Sel
P135 Relay Out 2 Sel Inversion Relay 2
R2NO +24V DC
F 76
16 Digital In3 Sel F
R2COM
P1270 29
DG3-
P148 Inversion out 4
15 D04
P1279 F 30
DG4+ * Digital Out4 Sel
Inversion In 4
P136 +24V DC
F
16 Digital In4 Sel
DG4-
Digital Inputs/Outputs & Mapping Standard and I/O Expansion Card
Expansion Digital Inputs (Optional) Expansion Digital Outputs (Optional)

Terminal Block 4
11
* P1387 6
31 P1271
DG9+ Inversion In 9
* P1280 P141 P149 Inversion Out 5
DG5+ Inversion In 5 D05
P137 5
F F
15 Digital In9 Sel Digital Out5 Sel
F COM_DO
35 Digital In5 Sel
DG9-
DG5- 12
32 * P1388 7
Inversion In 10 P1272
P1281 DG10+
* P142 P150 Inversion Out 6
DG6+ Inversion In 6 D06
P138 5
F F
F COM_DO
35 Digital In6 Sel
DG10-
DG6- 13
P1389 P1273 8
33 *
DG11+ Inversion In 11 P151 Inversion Out 7
P1282 P143 D07
DG7+ *
Inversion In 7 5
P139 F F
COM_DO
F
35 Digital In7 Sel
DG11-
DG7- 14
P1274 9
34 P1390
P152 Inversion Out 8
DG12+ Inversion In 12
P144
D08
P1283
DG8+ 5
Inversion In 8 F
P140 Digital Out8 Sel
F Digital In12 Sel COM_DO

15
F Digital In8 Sel
35 DG12-
DG8-

D-3
D-4
Analog Inputs / Outputs Analog Outputs

Analog Inputs Terminal Block 3
Terminal Block 1
From Digital Reference
D 21
Setting
P66 A AO1
Analog Input 1 P71 Anlg Out1 Sel C 22
Anlg In1 Config P73 P259 1
Anlg1 Tune Scale Anlg In1 Tune ACOM
Ref_1+ P62
F
P70 Anlg Out1 Scale
1 Anlg In1 Sel
HW + Volts
P295
input Σ Anlg In1 Target 23
2 type P1043 D
- Anlg In1 Cmp Err P67 A AO2
Ref_1- Window comparator Anlg Out2 Sel C 24
P72 P792 2
Anlg In1 Scale Anlg In1 Filter ACOM
P1404
Analog In1 Value P63
P1042 Anlg Out2 Scale
P74 Anlg In1 Cmp
Anlg In1 Offset
Expansion Analog Outputs (Optional)
D 1
P1045
P68 A AO3
Anlg In1 Cmp Eq
Anlg Out3 Sel C 2
Analog Inputs/Outputs and Mapping
1
ACOM

P64
Anlg Out3 Scale
P1044
Analog Input 2 P76 Anlg In1 Cmp Dly
P78 P260
Anlg In2 Config
Anlg2 Tune Scale Anlg In2 Tune
Ref_2+
3 From Digital Reference
HW + Volts D 3
Setting
input Σ P69 A AO4
4 type
- Anlg Out4 Sel C 4
2
Ref_2- ACOM
P77 F
P75 P65
P1405 Anlg In2 Scale Anlg In2 Sel Anlg Out4 Scale
P79 Anlg In2 Target
Anlg In2 Offset Tach Follower
Digital Encoder
From Digital Reference Terminal Block
Setting
Analog Input 3 P81
P83 P261 P80
Anlg In3 Config A+
Anlg3 Tune Scale Anlg In3 Tune Anlg In3 Sel
Ref_3+
5 A-
HW + Volts F
input Σ
6 type
B+
- P297
Ref_3- Anlg In3 Target B- P1021
Encoder Out Sel
P1406 Z+
Anlg In3 Scale
Z-
P84
Anlg In3 Offset
COM
+V
Speed Reference Selection
MOP Reset
P70 (digital input)
Terminal Block
Anlg In1 Sel
Digital Inputs
P75 (”0” if not defined) MOP Inc Reset
Anlg In2 Sel (digital input) INC
P80 MOP
Anlg In3 Sel MOP Dec DEC
(digital input)
Speed Sel 3
Speed Sel 2
Speed Sel 1
P1323
DPI P1 Select P47 P1375
P2 OUT MOP Select
Speed Ref A Pct MAX
P1324 P44 000 Maximum Speed
DPI P2 Select Speed Ref A
P1
P1325 P48 001 MIN
Minimum Speed
DPI P3 Select Speed Ref B Auto / Manual
P1326 P49 (Par 381 Drive Status 1, b15) ACCEL DECEL
P155 010
DPI P4 Select Speed Ref B Pct
Preset Speed 2
b15
P1327 P156 011 P22 P30
DPI P5 Select Preset Speed 3 Auto (0) MOP Accel Time MOP Decel Time
P1375 P157 100

MOP Select Preset Speed 4
P1021 P158 101 Minimum Speed Limit
Encoder Out Sel Preset Speed 5 P1
P159 110 Minimum Speed Jog
Preset Speed 6 P5 (Par 1328 Drive Logic Rslt, b02)
P160 111 Min Speed Fwd
b02
Preset Speed 7
Off
Manual Source
P70 (Par 381 Drive Status 1, b12-14)
Anlg In1 Sel
b14
b13
b12
P75 P6
Anlg In2 Sel Min Speed Rev
P267 000
P80 TB Manual Ref
Anlg In3 Sel 001
DPI Port 1 Reference
P1375
MOP Select 010
DPI Port 2 Reference Manual (1) P384
Spd Ref Out Pct
011 P385 To Speed Reference
DPI Port 3 Reference
Spd Ref Out
Generation Diagram
DPI Port 4 Reference 100
DPI Port 5 Reference 101
P70
Anlg In1 Sel
On
P75 P266
Anlg In2 Sel Jog Speed
P80
Anlg In3 Sel

D-5
D-6
Speed Reference Generation

P70
Anlg In1 Sel
P75
Anlg In2 Sel

P80
Anlg In3 Sel
P1323
DPI P1 Select
P1324
DPI P2 Select
P1325
Speed Reference Generation
DPI P3 Select
P1326
DPI P4 Select

P1327
DPI P5 Select
P1375
MOP Select
P111 P114 P1019
P1021 Ramp In Pct Ramp Out Pct Spd Draw Out Pct
Encoder Out Sel P110 P113 P1018
Ramp In Ramp Out Speed Draw Out
P42
Trim Ramp Speed Speed
P378
Trim Ramp Pct t t
From Speed Reference
Selection Diagram Zero Ramp Reference Zero
P245
P384 Speed Ramp En Speed Draw
Spd Ref Out Pct
T T On P1017
P385
Spd Ref Out
Σ Speed Ratio
P345 P344
Zero Ramp Input Zero Ramp Output Speed ratio To Speed
/ Current
10000 Overview
Off
Ramp Reference Block
0 t
Ramp Reference
P20 P114
P111 P373
Ramp In Pct Ramp Delay Ramp Out Pct
Freeze Ramp
P110 P113
Ramp In T Ramp Out
Freeze Ramp
Ramp Reference Block
P1410 Digital Input

Jog Ramp Time Command
P18 Fast Stop
P660 Ramp Type Select
Accel Time 1
Linear
P24 T
Accel Time 2 P38
Fast Stop Time
P662 S-Shape
Decel Time 1
P32
Decel Time 2
Accel/Decel 1/2 Command

(digital input)
P19
S Curve Time
P665
S Curve Accel 1
P667
S Curve Accel 2
P666
S Curve Decel 1
P668
S Curve Decel 2

D-7
D-8
Speed / Torque Regulator

Droop compensation
P698 +
Load Comp -
P41 P696
Current Reg In Droop Percent
Inertia / Loss Comp P1016

SpdFuncSelect
Speed Limits
P2 Inertia/loss
Maximum Speed P117
P3 Speed Reg In Pct
Max Speed Fwd P118
From Speed Reference Speed Reg In
Generation Diagram P4
Max Speed Rev
P1019 Speed Reg P/I P242 P353
Spd Draw Out Pct + + Speed Reg En Zero Torque
P1018
+ + P236
+ +
Σ Σ Σ Σ To Current Regulator
Speed Draw Out Spd Reg Out Pct T T Block Diagram
+ + +
Speed / Torque Regulator
P6
P70 Min Speed Rev
Anlg In1 Sel P99 P40 Zero Torque

P5 Spd Reg Kp Outpt Trim Torque Command
P75 Min Speed Fwd P100
Anlg In2 Sel P1 Spd Reg Ki Outpt
P80 Minimum Speed P39
Anlg In3 Sel P/I Regulator includes Torque Ref
Anit-windup Logic
P1323
DPI P1 Select
P1324
DPI P2 Select
P43
P1325 Trim Speed
DPI P3 Select
P1326
DPI P4 Select P70
Anlg In1 Sel
P1327
DPI P5 Select P75
Anlg In2 Sel
P1375
MOP Select P80
Anlg In3 Sel
P1021
Encoder Out Sel P1323
DPI P1 Select
P1324
DPI P2 Select
Speed Feedback + P1325
P924
Actual Speed Σ DPI P3 Select
+ P1326
Speed Up P1016 DPI P4 Select
SpdFuncSelect P1327
DPI P5 Select
Speed Up
P445 P447 P446

Spd Up Gain Pct Speed Up Filter Speed Up Base
Droop Compensation
From Digital Setting
or Analog Input
P698 P697
Load Comp Droop Filter P700
Droop Limit
P699
+ Enable Droop
P41 To Trim Speed
Current Reg In Σ
+ T Reference Sum
Low Pass Filter
P696
Droop Percent Zero
Droop Compensation - Inertia / Loss Compensation
Inertia / Loss Compensation

P106
Ref Zero Level
Speed
P1012
Inertia C Filter
P1015
Friction
P1016
1 SpdFuncSelect
n
P118
Speed Reg In +
T
P1013
d Torque Const
Low Pass Filter To Speed Regulator
Ouput Sum
P1014 P500
Inertia Field Ref Pct

D-9
D-10
Speed Feedback
Armature Feedback Bypass

P458
SpdReg FB Bypass
P414 = 3
P233
Fdbk Device Type
A Output Voltage
Speed Feedback Loss Motor
H
CEMF
Armature
Speed Feedback
P175
Rated Motor Volt
P1408
Tachometer Speed

P562 P414 = 2
Voltage + Anlg Tach Gain Fdbk Device Type
Tach
P563 DC Tach
P175 - Anlg Tach Zero
Rated Motor Volt P455
DC Tachometer
Spd Fdbk Error P121
Spd Feedback Pct
Speed P122
P420 Spd Feedback
Encoder Speed
A+ P651
Encoder State
A- P421
PD Output PID
P414 = 1
B+ Fdbk Device Type
B-
Encoder
Speed Z+
P169
Digital Encoder
Encoder PPR Index Storing

P456 P162 Z-
Fld Weaken Ratio P652
Max Feedback Spd Encoder Err Chk
COM
+V
P457
Spd Fdbk Control P911
Z Channel Enable
Speed Regulator PI Block
Speed P / I Base
P93 P459
Spd Reg Kp Base SpdReg Kp Bypass Bypass gains are used when P458 [SpdReg FB Bypass] = “Enabled” (1)
and the Encoder or Tachometer signal is lost, causing Armature Voltage
P94 P460 Feedback to be used.
Spd Reg Ki Base SpdReg Ki Bypass
P444
P181 Spd Fdbk Filter
Adaptive Spd En Anti-Windup
P87 P99 Torque Current Limits
Spd Reg Kp F Spd Reg Kp Out
Speed Regulator PI Block
P188
Adaptive P Gain1
P190
Adaptive P Gain2
P192
Adaptive P Gain3
+
+ P236
P118 Anti-Windup Σ
Spd Reg In Σ Spd Reg Out Pct
+ +
P183
Adaptive Ref Speed Adaptive P122
Spd Feedback P348
and Lock Speed Integ
P117 Speed Zero Logic
Spd Reg In Pct
T
P181
Adaptive Spd En
P88 P100 Zero
Spd Reg Ki F Spd Reg Ki Out
P189
Adaptive I Gain1
P191
Adaptive I Gain1
P193
Adaptive I Gain3

D-11
D-12
Speed Adaptive and Speed Zero Logic

Speed Adaptive Function
P186 P187 P181

Adaptive Joint 1 Adaptive Joint 2 Adaptive Spd En
P182
Adaptive Reg Typ
Gain
P188 P189
P190 P191
P192 P193
Speed Adaptive and Speed Zero Logic

%
P183 P117
Adaptive Ref OR Spd Reg In Pct
P184 P185
Speed Zero Logic Adaptive Spd 1 Adaptive Spd 2
P126 P125
Spd Zero P Gain Spd Zero P En
P106 T
Ref Zero Level >= Lock speed I
P124
&
Ref 0 level Spd Ref Zero En
Ramp Ref / Speed Ref
& T
>=
P123
Spd Zero I En Lock speed I
&
>
&
T =
Speed Zero
Speed
0 t
P108
Speed Zero Delay
Current Regulator
Current Limits
P7 P453
Current Limit Arm Resistance
Go to Motor
P454
P8 P10 Arm Inductance Parameters
Current Lim Pos Cur Lim Pos Out
P / I Regulator Modulator
P41
+ DC
From Speed / Torque Regulator Σ
Current Reg In Motor
-
Current Regulator
P9 P11
Current Lim Neg Cur Lim Neg Out P/I Regulator Includes
Feedback
Anti-Windup Logic P233 (Option)
Output Voltage
P715
Torq Limit Type
P199
P13
Arm Current Pct
T Torq Red CurLim P200
Arm Current
Torque
P342
Reduction
Torque Reduction
Torque Reduction
T Command
To rq ue To rq ue
Fwd Brdg Cur Lim Fwd Brdg Cur Lim
Fwd Brdg Cur Lim
Rev Brdg Cur Lim
Speed Speed
Rev Brdg Cur Lim

Rev Brdg Cur Lim Rev Brdg Cur Lim
Fwd Brdg Cur Lim
-1% of +1% of
Max Feedback Spd Max Feedback Spd
Motoring & Generating Torque Limit Torque Limit +/-


D-13
D-14
Field Current Regulator

Voltage Reg P / I Base
P493
Arm Volt Kp P97
Fld Reg Kp Base
P98 Field Current Limits
P494 Fld Reg Ki Base Energy Saving
P921 Arm Volt Ki P467
Out Volt Level Max Fld Curr Pct Max Field Output V oltage
Curr
Min Field
Voltage Regulator Curr
+ T
P175
Rated Motor Volt
Σ
_ P469
Field Mode Sel
P233 P498
Output Voltage Force Min Field
Field Current Regulator
P468
Min Fld Curr Pct
P499
Fld Economy En

Field Economy
Max Field Curr
Field Reg P / I Base

P91
Fld Reg Kp P495 Min Field Curr
Arm Volt Kp Base
S pd = 0 Thr
P92 P496
Fld Reg Ki Arm Volt Ki Base
P280 P107
Nom Mtr Fld Amps Speed Zero Level
P500
Field Ref Pct
Field Controller
I Field Curve
Field Reg P / I P497
Field Reg Enable
+
Σ
T
_
P374
Drv Fld Brdg Cur
P919 P916
Set Fld Curve Fld Const 40 Pct
P234
P920 P917 Fld Current Pct C1
Reset Fld Curve Fld Const 70 Pct
M
P918 D1
Fld Const 90 Pct
P280
Nom Mtr Fld Amps
Motor Parameters
Output
Voltage / Constant Torque Field Regulator
Torque Management
P175 P469
Rated Motor Volt Field Mode Sel
P374
Constant Power Drv Fld Brdg Cur
P468
Min Fld Curr Pct
P467
Max Fld Curr Pct
g
Motor Parameters
sin r
Ri owe
P
Speed
P456 P162
Fld Weaken Ratio Max Feedback Spd
P45
Max Ref Speed
P453 P454
Arm Resistance Arm Inductance P280
Nom Mtr Fld Amps
A C1
(A1)
P351
P199 Field Current
Arm Current Pct
P200
P233 Arm Current
Output Voltage M
P587
I Reg Error
H
(A2) D1

D-15
D-16
Speed Threshold / Speed Control
P101
Speed Thresh Pos
P122
Spd Feedback
[Digital Outx Sel]
= 2 “Spd Thresh”
P393
Speed Threshold
P102
Speed Thresh Neg
Speed Threshold / Speed Control

P103 0 t
Threshold Delay
P118
Speed Reg In P104
At Speed Error
[Digital Outx Sel]

= 3 “At Speed”
P122
Spd Feedback P394
At Speed
P105 0 t
At Speed Delay
P758 PID Control
Feed Fwd PID
Gain
P731 P773
PID Steady Delay PID Output Scale
P786
PID Source Thr
Steady P782
Gain
P787 PID Target
State
PID Source Gain
P765
PI Prop Gain PID
P793
PI Init Prop Gn
P418
Thr 2 sign PID Real FF PID
PID Control
P784 P771 P772

PI Upper Limit PI Output PID Output Sign
P760 P762
Gain P769
P761 Feed Fwd Sign: Enable PI +
PID Setpoint 1 Pos Gain = -1 + Σ
Neg Gain = +1 T +
ON
P785 P774
PI Lower Limit
PID Output
P771
P1046 PI Output
PID Accel Time P776
PI Central v1
P764 P777
PI Integral Gain PI Central v2
P734 P783
P1047 PI Init Intgl Gn PI integr freeze
PID Decel Time P779
PI Central v sel
P800 P794
Diameter Calc St Diameter Calc
T
P778
P763 PI Central v3
PID Feedback
P768 P770
+ PD Prop Gain 1 Enable PD
+ P788 P799
Σ PD Prop Gain 2 T + Minimum Diameter
ON
P790 P797
PD Prop Gain 3 Gear Box Ratio
P763
PID Feedback
P757 P771
PID Clamp P414 Diameter PI Output
Fdbk Device Type Calculator
P795
P759 DncrPosSpd
PID Error P766
PD Deriv Gain 1 P796
P789 P767 Encoder 1 Position Max Deviation
PD Deriv Gain 2 PD Deriv Filter
P791 P798
PD Deriv Gain 3 Dancer Constant

D-17
D-18
Scale Blocks
Scale Block 1
P488
Scale1 In Max
P484
+ + P485
Scale1 Input Σ X Σ Scale1 Output
+ +
Scale Blocks
P491
P489 Scale1 Out Off
Scale1 In Min
P492 P486 P487
Scale1 In Abs Scale1 Mul Scale1 Div

P490
Scale1 In Off
Scale Block 2 P557

Scale2 In Max
P553
+ + P554
Scale2 Input Σ X Σ Scale2 Output
+ +
P560
P558 Scale2 Out Off
Scale2 In Min
P561 P555 P556
Scale2 In Abs Scale2 Mul Scale2 Div
P559
Scale2 In Off
Note: Up to six scale blocks are available. Scale blocks 3-6 follow the same flow as scale blocks 1 and 2, shown here.
User Defined Parameters
User Defined Variables
P503 P504 P505 P506 P507 P508 P509 P519 P536

UserDefined0 UserDefined1 UserDefined2 UserDefined3 UserDefined4 UserDefined5 UserDefined6 UsrDefBitWrdA UsrDefBitWrdB
Digital
output
Digital
output
output
input
output
Analog
Analog
Analog
input
input
Digital
Analog
General Parameters
P510 P511 P512 P513 P514 P515 P516 P517 P518

UserDefined7 UserDefined8 UserDefined9 UserDefined10 UserDefined11 UserDefined12 UserDefined13 UserDefined14 UserDefined15

D-19
D-20
P750 Taper Current Limits

TrqTpr_Enable
Cur Lim Pos Out

or
Cur Lim Neg Out
P751
TrqTpr_Lim0
Taper Current Limits

P752
TrqTpr_Lim1
P753
TrqTpr_Lim2
P754
TrqTpr_Lim3
P755
TrqTpr_Lim4
Motor Max Speed

P756
TrqTpr_Spd
Unit Scaling
Unit Scaling
Unit Scale Factor User Value Factor
User P50 P54

UsrDsplyMult0 UsrValDiv1 Control Variable
Defined Variable
X X
P51 P53
UsrDsplyDiv0 UsrValMult1

D-21
D-22 Control Block Diagrams
Test Generator
Test Generator
P58
TstGen Output
Generator
output
P60
TstGen Amplitude
P61
TstGen Offset
Time
P59
TstGen Frequency

Control Block Diagrams D-23
P402 P401 P400

Spd Select 2 Spd Select 1 Spd Select 0 Reference
0 0 0 P44
Speed Ref A
0 0 1 P48
Speed Ref B
0 1 0 P155
Preset Speed 2
0 1 1 P156
Preset Speed 3
P157
1 0 0 Preset Speed 4
1 0 1 P158
Preset Speed 5
1 1 0 P159
Preset Speed 6
1 1 1 P160
Preset Speed 7

D-24 Control Block Diagrams
Fault / Alarm Mapping
Fault/Alarm Mapping
“Arm Overvoltage” (F5) “Fld Current Loss” (F6)

P203 P473
OverVolt Flt Cfg FldLoss Flt Cfg
0 = “Ignore” 0 = “Ignore”
1 = “Alarm” 1 = “Alarm”
2 = “Fault” 2 = “Fault”
“Auxiliary Input” (F2) “Encoder Loss” (F91)

P354 P478
Aux Inp Flt Cfg Spd Loss Flt Cfg
1 = “Alarm” 1 = “Alarm”
2 = “Fault” 2 = “Fault”
3 = “Quick Stop”
4 = “Normal Stop”
5 = “CurrLim Stop”
“Motor Over Temp” (F16)

P365
OverTemp Flt Cfg
0 = “Ignore”
1 = “Alarm”
2 = “Fault”
3 = “Quick Stop”
4 = “Normal Stop”
5 = “CurrLim Stop”

Appendix E
Installing a Communication Adapter
Communication Adapter The following Communication Adapter kits are available for use with the
Kits PowerFlex® DC drive:
Comm Option Catalog Number
BACnet® MS/TP RS-485 Communication Adapter 20-COMM-B
ControlNet™ Communication Adapter (Coax) 20-COMM-C
DeviceNet™ Communication Adapter 20-COMM-D
EtherNet/IP™ Communication Adapter 20-COMM-E
HVAC Communication Adapter 20-COMM-H
Interbus™ Communication Adapter 20-COMM-I
PROFIBUS™ DP Communication Adapter 20-COMM-P
ControlNet™ Communication Adapter (Fiber) 20-COMM-Q
Remote I/O Communication Adapter 20-COMM-R
RS-485 DF1 Communication Adapter 20-COMM-S
External Comms Power Supply 20-XCOMMAC-PS1
DPI External Communications Kit 20-XCOMMDC-BASE
External DPI I/O Option Board(1) 20-XCOMMIO-OPT1
Compact I/O to DPI/SCANport Module 1769-SM1
Serial Null Modem Adapter 1203-SNM
Smart Self-powered Serial Converter (RS-232) 1203-SSS
includes 1203-SFC and 1202-C10 Cables
Universal Serial Bus™ (USB) Converter 1203-USB
includes 2m USB, 20-HIM-H10 & 22-HIM-H10 Cables
(1) For use only with External DPI Communications Kits 20-XCOMM-DC-BASE.
What The Communication • Communication Adapter module w/captive screws

Adapter Kit Includes • Internal Interface cable
• Communication Adapter User Manual
• Additional components, based on the option selected
Tools That You Need • Phillips® screwdriver
Phillips® is a registered trademark of Phillips Screw Company.

E-2 Installing a Communication Adapter
Safety Precautions
ATTENTION: Only qualified personnel familiar with drives,
! power products and associated machinery should plan or
implement the installation, start-up, configuration and
subsequent maintenance of the system. Failure to comply may
result in personal injury and/or equipment damage.
ATTENTION: To avoid an electric shock hazard, ensure that all
! power to the drive has been removed before performing the
following.
ATTENTION: This drive contains ESD (Electrostatic
! Discharge) sensitive parts and assemblies. Static control
precautions are required when installing, testing, servicing or
repairing this assembly. Component damage may result if ESD
control procedures are not followed. If you are not familiar with
static control procedures, reference A-B publication 8000-4.5.2,
“Guarding Against Electrostatic Damage” or any other
applicable ESD protection handbook.
Installing the Follow these steps to install a communication adapter module:

Communication Adapter
Module in the Drive
ATTENTION: Remove power before making or breaking cable
! connections. When you remove or insert a cable connector with
power applied, an electrical arc may occur. An electrical arc can
cause personal injury or property damage by:
• sending an erroneous signal to your system’s field devices,
causing unintended machine motion
• causing an explosion in a hazardous environment
Electrical arcing causes excessive wear to contacts on both the
module and its mating connector. Worn contacts may create
electrical resistance.
1. Remove and lock-out all incoming power to the drive.
L1 L2 L3
I
2. Disconnect the DPI cable from the HIM on the drive.

Installing a Communication Adapter E-3
3. Remove the bottom cover from the drive:
a. On frame A drives, remove the screws that secure the bottom cover to
the drive, then slide the cover down and off the drive chassis.
Frame A
=
PORT
MOD
NET A
NET B
STS
Disconnect DPI cable.
b. On frame B and C drives, loosen, but do not remove, the screws that
secure the bottom cover to the drive, then slide the cover down and off
the drive chassis.
Frames B & C (Frame B shown)

=
Disconnect DPI cable.

4. Remove the top cover from the drive:
a. For frame A drives, press in on the sides at the bottom edge of the top
cover and at the same time pull the cover toward you to pull it
partially off the drive chassis. Next, at the top of the drive, pull the
cover forward, away from the drive, until the pins fit in the keyhole in
the top of the cover, then carefully lift the cover off of the drive
chassis.
Important:The HIM assembly is connected via a cable to the Control

board and therefore will not pull free from the drive until
disconnected. See page E-6 for instructions.
Frame A
=
PORT
MOD
NET A
NET B
STS
When metal pin fits in keyhole,

lift cover off drive chassis.

b. On frame B and C drives, loosen, but do not remove, the screws that
secure the top cover to the drive, then slide the cover up and off the
drive chassis.
Important:The HIM assembly is connected via a cable to the Control

board and therefore will not pull free from the drive until
disconnected. See page E-6 for instructions.
Frames B & C (Frame B shown) =
U C V D W

5. Disconnect the HIM Communication cable from the connector on the

upper right corner of the Control board and set the cover aside.
All Frames (Frame A shown) =
Pull tabs out

to disconnect
cable.
6. Secure and ground the Communication Adapter to the EMI Shield on

the drive using the four captive screws.
Important: All screws must be tightened, because the adapter is

grounded through a screw to the EMI shield.
Recommended tightening torque is 0.9 N•m (8 lb•in).
7. Connect the Internal Interface cable to the DPI connectors on the

Control board and the communication Adapter board.
Secure adapter to
EMI Shield with
four (4) screws.
Connect cable to
DPI connectors
on adapter and
control board.
8. Refer to the Adapter’s User Manual for network connection,

commissioning, and configuration information.

9. Install the HIM Communication cable in reverse order or removal.
10. Install the drive covers in reverse order of removal.

Notes:

Appendix F
Optional Analog and Digital I/O Expansion

Circuit Board
What This Option Board The optional I/O Expansion circuit board(1) is mounted on the Control
Provides board of the drive and provides these additional I/O signals:
• Four (4) Digital Inputs

• Four (4) Digital Outputs
• Two (2) Analog Outputs
Figure F.1 I/O Expansion Board Mounting Location
I/O Expansion Board I/O Expansion Board Control Board Standard Drive I/O
Terminal Blocks Terminal Blocks
I/O Expansion Board Wiring Table F.A Recommended Signal Wire Size
Wire Type and Size Tightening Torque
Flexible (mm2) multi-core (mm2) AWG N•m (lb•in)
0.14 - 1.5 0.14 - 1.5 28-16 0.4 (3.5)
A 75 x 2.5 x 0.4 mm (3.0 x 0.1 x 0.02 in.) flathead screwdriver is

recommended for connecting wire to the terminal block inputs. Strip the
ends of the cables to a length of 6.5 mm (0.26 in.).
Important: To improve the noise immunity it is recommended that you

connect the common of the outputs (terminals 2, 4, 5 and 15 of
the I/O Expansion board) with the ground (terminal 10 or 20)
on the standard I/O terminal blocks on the Control board. If this
is not possible, these terminals must be grounded by means of a
0.1 μf/250V capacitor.
(1) The Analog and Digital I/O Expansion circuit board is not factory installed.

F-2 Optional Analog and Digital I/O Expansion Circuit Board
Table F.B I/O Expansion Board Terminal Block 1 Designations

1 Analog Output 3 (+) ±10V, 5mA maximum
3 Analog Output 4 (+) ±10V, 5mA maximum
5 Digital Output Common
1
6 Digital Output 5 (+) Max volt. +30V, max cur. 50mA
2
3 7 Digital Output 6 (+)
4
6
7
9
10 10 +24VDC Drive supplied power for Digital
Outputs.
Max volt. +30V, max. cur. 80mA.
Table F.C I/O Expansion Board Terminal Block 2 Designations

11 Digital Input 9 Max volt. +30V, max cur. 15V/3.2mA, 24V/
12 Digital Input 10 5mA, and 30V/6.4mA.
11
12 13 Digital Input 11
13
14 14 Digital Input 12
15
15 Digital Input Common
Figure F.2 I/O Expansion Board Wiring Diagram
Control Board
I/O Expansion Board
Analog Outputs Digital Outputs Digital Inputs
+ 24 V
0 V 24
3 4 5 6 7 8 9 10 11 12
Supply
19 18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
+ 24 V
0V

Appendix G
Optional 115V AC to 24V DC I/O Converter

Circuit Board
What This Option Board The 115V AC to 24V DC I/O Converter circuit board(1) allows you to
Provides convert 115V AC digital input signals to 24V DC digital input signals in
order to interface with the standard digital I/O terminal blocks on the
PowerFlex DC drive Control board.
The card consists of:
• Eight (8) opto isolated 115V AC digital inputs
• Eight (8) interface outputs for the digital inputs on Control board of the
drive(2)
• Two (2) input terminals for the 24V DC power supply voltage
Figure G.1 115V AC to 24V DC I/O Converter Circuit Board Mounting Location
Control Board I/O Converter Board I/O Converter Board

Terminal Blocks
(1)
The 115V AC to 24V DC I/O Converter circuit board is not factory installed.
(2) If more than eight 115V AC digital input signals require conversion to 24V DC (i.e., the optional PowerFlex DC
drive I/O Expansion circuit board is used - see Appendix F), a second Converter board is required and must be
sourced and wired independently from the 115V AC to 24V DC I/O Converter board mounted on the Control
board and be mounted in an appropriate enclosure external to the PowerFlex DC drive enclosure.

G-2 Optional 115V AC to 24V DC I/O Converter Circuit Board
I/O Converter Board Wiring Table G.A Recommended Signal Wire Size
Wire Type and Size Tightening Torque
Flexible (mm2) multi-core (mm2) AWG N•m (lb•in)
0.14 - 1.5 0.14 - 1.5 28-16 0.4 (3.5)
A 75 x 2.5 x 0.4 mm (3.0 x 0.1 x 0.02 in.) flathead screwdriver is

recommended for connecting wire to the terminal block inputs. Strip the
ends of the cables to a length of 6.5 mm (0.26 in.).
Table G.B I/O Converter Board M_IN Terminal Block Designations
1 Digital Input 1 Rated input voltage:115V AC ±10% 50
2 Digital Input 2 - 60Hz.
3 Digital Input 3 ON input voltage: 115V AC ±10%
OFF input voltage: 0 - 70V AC
1
2
4 Digital Input 4 ON input current: 4 - 5.5mA
3
4 5 Digital Input 5
5
6
7
6 Digital Input 6
8C
OM 7 Digital Input 7
8 Digital Input 8
Com Digital Input Common
Table G.C I/O Converter Board M_OUT Terminal Block Designations

24V +24VDC Supply 24V DC ±10%, 40mA power supply.
Max. load 120mA.
Supply power can be provided by the
+24V DC supply on the Control board
I/O (terminal 19 - see Figure G.2 on
page G-3) or an external source (see
Figure G.3 on page G-3).
1 Digital Output 1 Output type: Open collector, PNP type
2 Digital Output 2 with 15kohm pull-down
3 Digital Output 3 Output current: 10mA max.
Delay time hw OFF to ON: 5ms (typ.)
4 Digital Output 4 Delay time hw ON to OFF: 50ms (typ.)
5 Digital Output 5
6 Digital Output 6
7 Digital Output 7
8 Digital Output 8
0V 24V Common Common for the power supply.
• If an internal supply is used, this
terminal must be wired to the
digital input common (terminal 16
or 35) on the Control board I/O.
24V
See Figure G.2 on page G-3.
1 • If an external supply is used, this
2
3
4
terminal must be wired to the
5
6
external 24V DC supply common
7 and the digital input common
8
0V
(terminal 16 or 35) on the Control
board I/O. See Figure G.3 on
page G-3.

Optional 115V AC to 24V DC I/O Converter Circuit Board G-3
Figure G.2 I/O Converter Board with Internal Supply Wiring Diagram
Main Control Board
115V AC to 24V DC I/O Board

OPTO OPTO
15k 15k
DC OUTPUT AC INPUT
24V 1 2 3 4 5 6 7 8 0V 1 2 3 4 5 6 7 8 COM
M_OUT M_IN
To Digital Inputs
(Terminals 12-15, 31-34)
on Control Board
To Drive To Digital Input Common

Supplied (Terminal 16 or 35) External 115V AC
+24V DC and 24V Supply Common
(Terminal 19) (Terminal 18)
on Control Board on Control Board
Internal Wiring Customer Wiring
Figure G.3 I/O Converter Board with External Supply Wiring Diagram
Main Control Board
115V AC to 24V DC I/O Board
OPTO OPTO
15k 15k
DC OUTPUT AC INPUT
24V 1 2 3 4 5 6 7 8 0V 1 2 3 4 5 6 7 8 COM
M_OUT M_IN
To Drive Digital Inputs

(Terminals 12-15, 31-34)
To Digital
From Input Common To External External 115V AC
External (Terminal 16 or 35) 24V DC
+24V DC Supply
Supply Internal Wiring Common Customer Wiring

G-4 Optional 115V AC to 24V DC I/O Converter Circuit Board
Notes:

Index
Numerics Agency Certification A-1

115V AC to 24V DC I/O Converter circuit Alarms
board G-1 AnalogCflct 4-7
Arm Voltage 4-7
2-Wire Control Non-Reversing, Wiring 1-38
Auxiliary Input 4-7
2-Wire Control Reversing, Wiring 1-39
BipolarCflct 4-7
3-Wire Control, Wiring 1-39 CntactrCflct 4-8
DigInCflcA 4-8
A DigInCflctB 4-8
DigInCflctC 4-8
AC Input Contactors
Encoder Loss 4-8
Configuration 1-9
EncoderCflct 4-8
Recommended A-17
Fld Current Loss 4-9
AC Input Line Reactors Motor Over Temp 4-9
Configuration 1-9 Non-Configurable 4-1
Recommended A-17 Start At PowerUp 4-9
AC Input Voltages 1-15 User Configurable 4-1
AC Line Freq 3-13 Visual Notification of 4-3
AC Line Voltage 3-13 Alarms Group 3-53, 3-54
AC Undervoltage Fault 4-4 ALT Key
Acc Dec Filter 3-30 Functions B-2
Accel Mask 3-58 Analog Conflict Alarm 4-7
Accel Owner 3-59 Analog In1 Value 3-64
Accel Status 3-50 Analog In2 Value 3-64
Accel Time 1 3-30 Analog In3 Value 3-64
Accel Time 2 3-29 Analog Input Configuration C-1
Act Spd Filter 3-20 Analog Input Signal Comparison C-2
Act Ten Ref Pct 3-43 Analog Input, Wiring 1-38
Actual Comp 3-44 Analog Inputs Group 3-62, 3-63, 3-64
Actual Speed 3-12 Analog Output, Wiring 1-38
Actuator Delay 3-32 Analog Outputs Group 3-64
Adaptive I Gain1 3-33 Anlg In1 Cmp 3-63
Adaptive I Gain2 3-33 Anlg In1 Cmp Dly 3-63
Adaptive I Gain3 3-33 Anlg In1 Cmp Eq 3-63
Adaptive Joint 1 3-33 Anlg In1 Cmp Err 3-63
Adaptive Joint 2 3-33 Anlg In1 Config 3-62
Adaptive P Gain1 3-33 Anlg In1 Filter 3-63
Adaptive P Gain2 3-33 Anlg In1 Offset 3-63
Adaptive P Gain3 3-33 Anlg In1 Scale 3-62
Adaptive Ref 3-32 Anlg In1 Sel 3-62
Adaptive Reg Typ 3-32 Anlg In1 Target 3-63
Adaptive Spd 1 3-32 Anlg In1 Tune 3-63
Adaptive Spd 2 3-32 Anlg In2 Config 3-62
Adaptive Spd En 3-32 Anlg In2 Offset 3-63
Adaptive Speed Regulator Function C-17 Anlg In2 Scale 3-62
Adaptv Regulator Group 3-32, 3-33 Anlg In2 Sel 3-62

Index-2
Anlg In2 Target 3-63 Autotune Group 3-20, 3-21

Anlg In2 Tune 3-63 Aux Inp Flt Cfg 3-53
Anlg In3 Config 3-62 Auxiliary Input Alarm 4-7
Anlg In3 Offset 3-63 Auxiliary Input Fault 4-4
Anlg In3 Scale 3-62
Anlg In3 Sel 3-62 B
Anlg In3 Target 3-63
Base Omega 3-41
Anlg In3 Tune 3-63
Bipolar Conflict Alarm 4-7
Anlg Out1 Scale 3-64
Bipolar Inputs 1-32
Anlg Out1 Sel 3-64
Brake Resistors A-19
Anlg Out2 Sel 3-64
C
Anlg Out3 Sel 3-64 Cable Recommendations 1-14
Anlg Out4 Scale 3-64 Cable Spacing Example 1-14
Anlg Out4 Sel 3-64 Cable Spacing Notes 1-15
Anlg Tach Gain 3-19 Cable Spacing Recommendations 1-14
Anlg Tach Zero 3-19 Changed Parameters, Viewing B-4
Anlg1 Tune Scale 3-62 Changing Speed Sources C-13
Anlg2 Tune Scale 3-62 Clear Fault Que 3-52
Anlg3 Tune Scale 3-62 Clearing Faults 4-3
Applications File 3-34 Close Loop Comp 3-44
Arm Current 3-12 Closed Loop En 3-44
Arm Current Pct 3-12 Closing Speed 3-32
Arm Inductance 3-20 Comm Control Group 3-58
Arm Resistance 3-20 Commissioning a Drive 2-1
Arm Volt Ki 3-27 Common Mode Interference 1-32
Arm Volt Ki Base 3-27 Communication Adapter E-1

Installing E-1
Arm Volt Kp 3-27
Communication Adapter Kits E-1
Arm Volt Kp Base 3-27
Communications
Armature Converter Terminal Block
Logic Command Word A-5
Location, Frame A 1-20
Logic Status Word A-6
Location, Frame B 1-20
Programmable Controller Configurations
Location, Frame C 1-21
A-5
Armature Overvoltage Fault 4-4
Communications File 3-58
Armature Terminals
Configuring a DC Output Contactor 1-9
Wire Sizes 1-22
Configuring a Klixon 1-26
Armature Voltage Alarm 4-7
Configuring an AC Input Contactor 1-9
At Speed 3-49
Configuring an AC Input Line Reactor 1-9
At Speed Delay 3-25
Constant J Comp 3-42
At Speed Error 3-25
Contactor Conflict Alarm 4-8
At Zero Speed 3-49
ContactorControl 3-67
Auto Speed Sources C-13
Contactors
Auto/Manual Examples C-14
Configuring 1-9
Autotune Cur Lim 3-21

Index-3
Control Block Diagrams D-1 Datalinks Group 3-60

Control Circuit DC Analog Tachometer
Circuit Breaker 1-11 DIP Switch S4 Settings 1-34
Fuses 1-11 Terminal Block Location 1-42
Input Current 1-11 Terminal Designations 1-42
Protection 1-11 DC Contactor Crimp Lug Kit Specifications
Control Wire Routing 1-42 A-21
Copycat B-4 DC Output Contactors 1-10, A-19
Cur Lim Neg Out 3-12 Configuration 1-9
Cur Lim Pos Out 3-12 DC Output Voltage 1-16
Armature 1-16
Current Lim Neg 3-17
Field 1-16
Current Lim Pos 3-17
Decel Mask 3-59
Current Limit 3-16
Decel Owner 3-59
Current Meters Group 3-12
Decel Status 3-50
Current Reg In 3-12
Decel Time 1 3-30
Current Regulator Tune Adjustments C-26
Decel Time 2 3-30
Current/Speed Curve Function C-4
Defaults, Resetting to B-4
CurrLimit Active 3-47
Diagnostic Data, Viewing B-4
CurrReg Autotune 3-20
Diagnostics Group 3-47, 3-48, 3-49, 3-50,
3-51, 3-52
D Diam Calc Dis 3-41
Dancer Constant 3-40 Diam Inc Dec En 3-42
Data In A1 3-60 Diam init filter 3-42
Data In A2 3-60 Diam Preset 0 3-41
Data In Ax 3-60 Diam Preset 1 3-41
Data In B1 3-60 Diam Preset 2 3-42
Data In B2 3-60 Diam Preset 3 3-42
Data In C1 3-60 Diam Preset Sel 3-42
Data In C2 3-60 Diam stdy delay 3-42
Data In D1 3-60 Diam Threshold 3-41
Data In D2 3-60 Diameter Calc 3-40
Data In SelData 3-60 Diameter Calc Group 3-40, 3-41, 3-42
Data In Val Sel 3-60 Diameter Calc St 3-40
Data Nameplate p-2 Diameter Filter 3-41
Data Out A1 3-60 Diameter Reached 3-41
Data Out A2 3-60 Diameter Reset 3-41
Data Out Ax 3-60 Dig In Status 3-67
Data Out B1 3-60 Dig In Term 1 3-67
Data Out B2 3-60 Dig In Term 10 3-67
Data Out C1 3-60 Dig In Term 11 3-67
Data Out C2 3-60 Dig In Term 12 3-67
Data Out D1 3-60 Dig In Term 2 3-67
Data Out D2 3-60 Dig In Term 3 3-67
Data, Saving B-4 Dig In Term 4 3-67

Index-4
Dig In Term 5 3-67 DIP Switch S12

Dig In Term 6 3-67 Description of 1-33
Dig In Term 7 3-67 Location 1-32
Dig In Term 8 3-67 DIP Switch S14
Description of 1-33
Dig In Term 9 3-67
Location 1-32
Dig Out Status 3-70
Settings 1-24
Digital In1 Sel 3-65
DIP Switch S15
Digital In10 Sel 3-65 Description of 1-33
Digital In11 Sel 3-65 Location 1-32
Digital In12 Sel 3-65 Settings 1-34
Digital In2 Sel 3-65 DIP Switch S18
Location 1-32
DIP Switch S20
Description of 1-33
Digital In8 Sel 3-65 Location 1-32
Digital Input Conflict A Alarm 4-8 Description of 1-33
Digital Input Conflict B Alarm 4-8 Location 1-32
Digital Input Conflict C Alarm 4-8 DIP Switch S3
Digital Input Option Definitions 3-66 Description of 1-33
Digital Inputs Group 3-65, 3-66, 3-67 Location 1-32
Digital Out1 Sel 3-68 DIP Switch S4
Description of 1-33
Digital Out2 Sel 3-68
Location 1-32
DIP Switch S9
Description of 1-33
Digital Out5 Sel 3-68 Location 1-32
Digital Out6 Sel 3-68 Direction Mask 3-58
Digital Out7 Sel 3-68 Direction Mode 3-46
Digital Out8 Sel 3-68 Direction Owner 3-59
Digital Output Option Definitions 3-69 Discrete Speeds Group 3-23, 3-24
Digital Outputs Group 3-68, 3-69, 3-70, 3-71 DncrPosSpd 3-40
DIP Switch S0 DPI Baud Rate 3-58
Description of 1-33
DPI Fdbk Select 3-58
Location 1-32
DPI Inputs Group 3-71
DIP Switch S1
DPI P1 Select 3-71
Description of 1-33
Location 1-32 DPI P2 Select 3-71
DIP Switch S10 DPI P3 Select 3-71
Description of 1-33 DPI P4 Select 3-71
Location 1-32 DPI P5 Select 3-71
DIP Switch S11 DPI Port Sel 3-58
Description of 1-33 DPI Port Value 3-58
Location 1-32 Drive Alarm 1 3-54

Index-5
Drive Data Group 3-13 E

Drive Dimensions Editing Parameters 3-1, B-5
Frame A 1-3
EEPROM Error Fault 4-4
Frame B 1-4
Frame C 1-5 Elapsed Lifetime 3-13
Drive Grounding Points 1-12 Electrostatic Discharge Precaution p-3
Drive Logic Rslt 3-51 Enable Droop 3-31
Drive Memory Group 3-46 Enable Input, Wiring 1-38
Drive Mounting Enable PD 3-36

Dimensions 1-3 Enable PI 3-34
Lifting Precautions 1-5 Enable PID 3-39
Minimum Clearance Requirements 1-2 Enclosure Rating 1-2
Operating Conditions 1-2 Encoder Conflict Alarm 4-8
Weights 1-3
Encoder Err Chk 3-20
Drive Overload Fault 4-4
Encoder Ground 1-13
Drive Power Wiring 1-15
Encoder Loss Alarm 4-8
Drive Size 3-13
Encoder Loss Fault 4-4
Drive Start-Up
Encoder Out Sel 3-20
Checklist 2-2
Encoder PPR 3-19
Procedures 2-1
Encoder Speed 3-11
Drive Status 1 3-48
Encoder State 3-50
Drive Status 2 3-48
Encoder Terminal Block 1-40
Drive Status Indicators 4-2
Encoder Terminal Block Designations 1-40
Drive Storage Conditions p-1
Encoder Terminal Block Location 1-40
Drive Type 3-13
Encoder Wiring 1-41
Drive Type Sel 3-14
Drive Weights
Frame A 1-3 F
Frame B 1-4 Factory Defaults, Resetting to B-4
Frame C - Regenerative 1-5
Fast Stop Status 3-50
DriveExplorer 2-4, 3-1
Fast Stop Time 3-31
DriveTools SP 2-4, 3-1
Fault 1 Code 3-53
Droop Compensation C-5
Fault 1 Time 3-53
Droop Filter 3-31
Fault 10 Code 3-53
Droop Function C-5
Fault 10 Time 3-53
Droop Limit 3-31
Fault 2 Code 3-53
Droop Percent 3-31
Fault 2 Time 3-53
Drv Fld Brdg Cur 3-14
Fault 3 Code 3-53
Dsp Error Fault 4-4
Fault 3 Time 3-53
Dynamic Brake Resistor
Fault 4 Code 3-53
Configuring 1-9
Fault 4 Time 3-53
Recommended A-19
Using 1-10 Fault 5 Code 3-53
Dynamic Control File 3-29 Fault 5 Time 3-53
Dynamic Friction 3-42 Fault 6 Code 3-53
Fault 6 Time 3-53
Fault 7 Code 3-53

Index-6
Fault 7 Time 3-53 Faults

Fault 8 Code 3-53 AC Undervoltage 4-4
Fault 8 Time 3-53 Arm Overvoltage 4-4
Auxiliary Input 4-4
Fault 9 Code 3-53
Descriptions 4-4
Fault 9 Time 3-53 Drive Overload 4-4
Fault Arm Amps 3-53 Dsp Error 4-4
Fault Clear 3-52 EEPROM Error 4-4
Fault Clr Mask 3-58 Encoder Loss 4-4
Fault Clr Mode 3-52 Fld Current Loss 4-4
Hardware Fault 4-5
Fault Clr Owner 3-59
Heatsink OvrTemp 4-5
Fault Field Amps 3-53
Interrupt Error 4-5
Fault Queue B-4 Inverting Fault 4-5
Fault Speed 3-53 Main Contactor 4-5
Fault Voltage 3-53 Manually Clearing 4-3
FaultCode 3-13 Motor Over Temp 4-5
No Fault 4-5
Non-Configurable 4-1
Overcurrent 4-5
Overspeed 4-5
Params Defaulted 4-5
Port 1 Adapter 4-5
Port 1 DPI Loss 4-6
Port 2 Adapter 4-5
Port 2 DPI Loss 4-6
Port 3 Adapter 4-5
Port 3 DPI Loss 4-6
Port 4 Adapter 4-5
Port 4 DPI Loss 4-6
Port 5 Adapter 4-5
Port 5 DPI Loss 4-6
Power Failure 4-6
STune Aborted 4-6
STune CurLimit 4-6
STune FrictionLo 4-6
STune LoadHi 4-6
User Configurable 4-1
Visual Notification 4-3
Faults Group 3-52, 3-53
Fdbk Device Type 3-19
Feed Fwd PID 3-37
Field Circuit Terminal Block
Location, Frame A 1-23
Location, Frame B 1-23
Location, Frame C 1-24
Field Config Group 3-14, 3-15, 3-16
Field Converter
Votage Regulator Tuning C-31
Field Current 3-12

Index-7
Field Current Curve C-33 G

Tuning C-33
Gear Box Ratio 3-40
Field Current Loss Alarm 4-9
Grounding
Field Current Loss Fault 4-4 Encoder 1-13
Field Current Pct 3-12 Power Feeder 1-13
Field Current Regulator Requirements 1-12
Fine Tuning C-26 Safety, PE 1-12
Field Current Resistors Tachometer 1-13
S14 1-24 Grounding Points
Setting 1-24 Drive 1-12
Field Econ Delay 3-16
Field Economy En 3-16 H
Field Mode Sel 3-15
Hardware Fault 4-5
Field Reg Enable 3-15
Heatsink Over Temperature Fault 4-5
Field Terminals
HIM
Wire Sizes 1-24
ALT Key B-2
File-Group-Parameter List B-4 Connection Points B-1
File-Group-Parameter Structure 3-3 Display Elements B-1
Filt Torq Cur 3-19 DPI Port 1 B-1
Filt TorqCur Pct 3-12 DPI Port 2 B-1
Final Diameter 3-43 DPI Port 3 B-1
DPI Port 5 B-1
Fine Tuning the Field Current Regulator
Installing B-6
C-26
LEDs 4-2
Fine Tuning the Regulators C-25
Menu Structure B-3
Fine Tuning the Speed Regulator C-29 Removing B-6
Fine Tuning the Voltage Regulator C-31 Viewing and Editing Parameters with B-5
Fld Const 40 Pct 3-16 HIM Menu Structure B-4
Fld Const 70 Pct 3-16 HIM Menus
Fld Const 90 Pct 3-16 Device Select B-4
Fld Current Pct 3-12 Diagnostics B-4
Memory Storage B-4
Fld Reg Ki 3-14
Parameter B-4
Fld Reg Ki Base 3-15
Preferences B-5
Fld Reg Kp 3-14
Fld Reg Kp Base 3-14
Fld Weaken Ratio 3-15
I
FldLoss Flt Cfg 3-54 I Reg Error 3-20
Flying Start En 3-27 I/O and Control Wire Routing 1-42
Force Min Field 3-15 I/O Converter Circuit Board G-1
Mounting Location G-1
Freeze Ramp 3-30
Recommended Signal Wire Size G-2
Friction 3-21
Terminal Block Designations G-2
Functions, ALT Key B-2 Wiring Diagrams G-3
Fuses
Control Power Circuit A-15
Input Power Circuit A-7, A-11

Index-8
I/O Expansion Circuit Board F-1 Inversion Out 8 3-70

Mounting Location F-1 Inversion Relay1 3-71
Recommended Signal Wire Size F-1 Inversion Relay2 3-70
Terminal Block Designations F-2
Inverting Fault 4-5
Wiring Diagram F-2
I/O Wire Routning 1-42
I/O Wire Sizes 1-35 J
I/O Wiring Examples 1-37 Jog Mask 3-58
Indicators Jog Off Delay 3-24
Drive Status 4-2 Jog Owner 3-59
Inertia 3-21 Jog Ramp Time 3-29
Inertia C Filter 3-20 Jog Speed 3-23
InertiaCompAct 3-28 Jog TW Enable 3-45
InertiaCompVar 3-28 Jog TW Speed 3-45
Initial Diameter 3-43 Joystick, Wiring 1-37
Input Potentiometer 1-37 K
Input Power Circuit Protection
Klixons
Fuse Designations - Frame A A-7
Using 1-26
Fuse Designations - Frame B A-7
Fuse Designations - Frame C A-11
Installation 1-1 L
Installing a Communication Adapter E-1 Last Stop Source 3-52
Installing the HIM B-6 LCD HIM
Int Acc Calc En 3-43 Menus B-4
Interrupt Error Fault 4-5 LEDs
Inversion In 1 3-67 Drive Status 4-2
MOD 4-2
Inversion In 10 3-67
NET A 4-2
Inversion In 11 3-67 NET B 4-2
Inversion In 12 3-67 PORT 4-2
Inversion In 2 3-67 STS 4-2
Inversion In 3 3-67 Limits Group 3-23
Inversion In 4 3-67 Line Accel Pct 3-43
Inversion In 5 3-67 Line Decel Pct 3-43
Inversion In 6 3-67 Line FastStp Pct 3-43
Inversion In 7 3-67 Line Reactor
Inversion In 8 3-67 Configuration 1-9
Inversion In 9 3-67 Recommended A-17
Inversion Out 1 3-70 Line Spd Gain 3-41
Inversion Out 2 3-70 Line Spd Source 3-44
Inversion Out 3 3-70 Line Spd Thresh 3-41
Inversion Out 4 3-70 Line Speed Pct 3-41
Inversion Out 5 3-70 Linear Parameter List 3-3
Inversion Out 6 3-70 Linking Parameters Via the Scale Block
Parameters C-17
Inversion Out 7 3-70
Load Comp 3-31

Index-9
Load Limits Group 3-31 Motor Control File 3-14

Local Mask 3-59 Motor Data Group 3-14
Local Owner 3-59 Motor Over Temperature Alarm 4-9
Lock Speed Integ 3-26 Motor Over Temperature Fault 4-5
Logic Command Word A-5
Logic Mask 3-2, 3-58, 3-60 N
Logic Mask Act 3-60
NET A LED 4-2
Logic Status Word A-6
NET B LED 4-2
Lug Kits A-21
Nom Mtr Arm Amps 3-14
Nom Mtr Fld Amps 3-14
M Normally Open Relay Outputs 1-25
Main Contactor Fault 4-5 Numbered Parameter List 3-3, B-4
Man Ref Preload 3-46
Manual Speed Sources C-13 O
Manually Adjusting the Current Regulator
Offs Accel Time 3-44
Tune Settings C-26
Opening Delay 3-32
Manually Clearing Faults 4-3
Operating Temperature 1-2
Manuals
Additional Information p-2 Option Definitions, Digital Inputs 3-66
Masks & Owners Group 3-2, 3-58, 3-59 Option Definitions, Digital Outputs 3-69
Materl Width Pct 3-42 Option Definitions, Relay Outputs 3-69
Max Deviation 3-40 Out Volt Level 3-16
Max Diameter 3-41 Output Power 3-13
Max Feedback Spd 3-14 Output Voltage 3-13
Max Fld Curr Pct 3-15 Overcurrent Fault 4-5
Max Ref Speed 3-14 OverCurrent Thr 3-54
Max Speed Fwd 3-23 Overspeed Fault 4-5
Max Speed Rev 3-23 OverTemp Flt Cfg 3-53
Maximum Speed 3-23 OverVolt Flt Cfg 3-53
Menu Structure, HIM B-4

Min Fld Curr Pct 3-15 P
Min Speed Fwd 3-23 Param Access Lvl 3-46
Min Speed Rev 3-23 Parameter
Minimum Diameter 3-40 Descriptions 3-1
Minimum Speed 3-23 Parameter Access Level, Changing B-4
MOD LED 4-2 Parameter Cross Reference by Name 3-72
Monitor File 3-11 Parameter Cross Reference by Number
MOP Accel Time 3-29 3-77
MOP Dec Active 3-49

MOP Decel Time 3-29
MOP Inc Active 3-49
MOP Mask 3-58
MOP Owner 3-59
MOP Select 3-46

Index-10
Parameter Files Parameter Views

Applications 3-34 Advanced 3-6
Communications 3-58 Basic 3-4
Dynamic Control 3-29
Monitor 3-11
Motor Control 3-14
Speed Command 3-23
Utility 3-46
Parameter Groups
Adaptv Regulator 3-32, 3-33
Alarms 3-53, 3-54
Analog Inputs 3-62, 3-63, 3-64
Analog Outputs 3-64
Autotune 3-20, 3-21
Comm Control 3-58
Current Meters 3-12
Datalinks 3-60
Diagnostics 3-47, 3-48, 3-49, 3-50, 3-51,
3-52
Diameter Calc 3-40, 3-41, 3-42
Digital Inputs 3-65, 3-66, 3-67
Digital Outputs 3-68, 3-69, 3-70, 3-71
Discrete Speeds 3-23, 3-24
DPI Inputs 3-71
Drive Data 3-13
Drive Memory 3-46
Faults 3-52, 3-53
Field Config 3-14, 3-15, 3-16
Limits 3-23
Load Limits 3-31
Masks & Owners 3-2, 3-58, 3-59
Motor Data 3-14
PD Control 3-36
PI Control 3-34, 3-35
PID Control 3-36, 3-37, 3-38, 3-39
Ramp Rates 3-29, 3-30
Reference Config 3-46
Restart Modes 3-32
Scale Blocks 3-39, 3-40
Security 3-60, 3-61
Speed Feedback 3-19, 3-20
Speed Meters 3-11, 3-12
Speed References 3-24
Speed Regulator 3-24
Stop Modes 3-31, 3-32
Test Generator 3-22
Torq Attributes 3-16, 3-17, 3-18, 3-19
User Defined 3-54, 3-55, 3-56, 3-57
Winder Functions 3-42, 3-43, 3-44, 3-45

Index-11
Parameters Anlg In3 Target 3-63

AC Line Freq 3-13 Anlg In3 Tune 3-63
AC Line Voltage 3-13 Anlg Out1 Scale 3-64
Acc Dec Filter 3-30 Anlg Out1 Sel 3-64
Accel Mask 3-58 Anlg Out2 Scale 3-64
Accel Owner 3-59 Anlg Out2 Sel 3-64
Accel Status 3-50 Anlg Out3 Scale 3-64
Accel Time 1 3-30 Anlg Out3 Sel 3-64
Accel Time 2 3-29 Anlg Out4 Scale 3-64
Act Spd Filter 3-20 Anlg Out4 Sel 3-64
Act Ten Ref Pct 3-43 Anlg Tach Gain 3-19
Actual Comp 3-44 Anlg Tach Zero 3-19
Actual Speed 3-12 Anlg1 Tune Scale 3-62
Actuator Delay 3-32 Anlg2 Tune Scale 3-62
Adaptive I Gain1 3-33 Anlg3 Tune Scale 3-62
Adaptive I Gain2 3-33 Arm Current 3-12
Adaptive I Gain3 3-33 Arm Current Pct 3-12
Adaptive Joint 1 3-33 Arm Inductance 3-20
Adaptive Joint 2 3-33 Arm Resistance 3-20
Adaptive P Gain1 3-33 Arm Volt Ki 3-27
Adaptive P Gain2 3-33 Arm Volt Ki Base 3-27
Adaptive P Gain3 3-33 Arm Volt Kp 3-27
Adaptive Ref 3-32 Arm Volt Kp Base 3-27
Adaptive Reg Typ 3-32 At Speed 3-49
Adaptive Spd 1 3-32 At Speed Delay 3-25
Adaptive Spd 2 3-32 At Speed Error 3-25
Adaptive Spd En 3-32 At Zero Speed 3-49
Analog In1 Value 3-64 Autotune Cur Lim 3-21
Analog In2 Value 3-64 Aux Inp Flt Cfg 3-53
Analog In3 Value 3-64 Base Omega 3-41
Anlg In1 Cmp 3-63 Clear Fault Que 3-52
Anlg In1 Cmp Dly 3-63 Close Loop Comp 3-44
Anlg In1 Cmp Eq 3-63 Closed Loop En 3-44
Anlg In1 Cmp Err 3-63 Closing Speed 3-32
Anlg In1 Config 3-62 Constant J Comp 3-42
Anlg In1 Filter 3-63 ContactorControl 3-67
Anlg In1 Offset 3-63 Cur Lim Neg Out 3-12
Anlg In1 Scale 3-62 Cur Lim Pos Out 3-12
Anlg In1 Sel 3-62 Current Lim Neg 3-17
Anlg In1 Target 3-63 Current Lim Pos 3-17
Anlg In1 Tune 3-63 Current Limit 3-16
Anlg In2 Config 3-62 Current Reg In 3-12
Anlg In2 Offset 3-63 CurrLimit Active 3-47
Anlg In2 Scale 3-62 CurrReg Autotune 3-20
Anlg In2 Sel 3-62 Dancer Constant 3-40
Anlg In2 Target 3-63 Data In A1 3-60
Anlg In2 Tune 3-63 Data In A2 3-60
Anlg In3 Config 3-62 Data In Ax 3-60
Anlg In3 Offset 3-63 Data In B1 3-60
Anlg In3 Scale 3-62 Data In B2 3-60
Anlg In3 Sel 3-62 Data In C1 3-60

Index-12
Data In C2 3-60 Digital In12 Sel 3-65

Data In D1 3-60 Digital In2 Sel 3-65
Data In D2 3-60 Digital In3 Sel 3-65
Data In SelData 3-60 Digital In4 Sel 3-65
Data In Val Sel 3-60 Digital In5 Sel 3-65
Data Out A1 3-60 Digital In6 Sel 3-65
Data Out A2 3-60 Digital In7 Sel 3-65
Data Out Ax 3-60 Digital In8 Sel 3-65
Data Out B1 3-60 Digital In9 Sel 3-65
Data Out B2 3-60 Digital Out1 Sel 3-68
Data Out C1 3-60 Digital Out2 Sel 3-68
Data Out C2 3-60 Digital Out3 Sel 3-68
Data Out D1 3-60 Digital Out4 Sel 3-68
Data Out D2 3-60 Digital Out5 Sel 3-68
Decel Mask 3-59 Digital Out6 Sel 3-68
Decel Owner 3-59 Digital Out7 Sel 3-68
Decel Status 3-50 Digital Out8 Sel 3-68
Decel Time 1 3-30 Direction Mask 3-58
Decel Time 2 3-30 Direction Mode 3-46
Diam Calc Dis 3-41 Direction Owner 3-59
Diam Inc Dec En 3-42 DncrPosSpd 3-40
Diam init filter 3-42 DPI Baud Rate 3-58
Diam Preset 0 3-41 DPI Fdbk Select 3-58
Diam Preset 1 3-41 DPI P1 Select 3-71
Diam Preset Sel 3-42 DPI P4 Select 3-71
Diam stdy delay 3-42 DPI P5 Select 3-71
Diam Threshold 3-41 DPI Port Sel 3-58
Diameter Calc 3-40 DPI Port Value 3-58
Diameter Calc St 3-40 Drive Alarm 1 3-54
Diameter Filter 3-41 Drive Logic Rslt 3-51
Diameter Reached 3-41 Drive Size 3-13
Diameter Reset 3-41 Drive Status 1 3-48
Dig In Status 3-67 Drive Status 2 3-48
Dig In Term 1 3-67 Drive Type 3-13
Dig In Term 10 3-67 Drive Type Sel 3-14
Dig In Term 11 3-67 Droop Filter 3-31
Dig In Term 12 3-67 Droop Limit 3-31
Dig In Term 2 3-67 Droop Percent 3-31
Dig In Term 3 3-67 Drv Fld Brdg Cur 3-14
Dig In Term 4 3-67 Dynamic Friction 3-42
Dig In Term 5 3-67 Editing B-5
Dig In Term 6 3-67 Elapsed Lifetime 3-13
Dig In Term 7 3-67 Enable Droop 3-31
Dig In Term 8 3-67 Enable PD 3-36
Dig In Term 9 3-67 Enable PI 3-34
Dig Out Status 3-70 Enable PID 3-39
Digital In1 Sel 3-65 Encoder Err Chk 3-20
Digital In10 Sel 3-65 Encoder Out Sel 3-20
Digital In11 Sel 3-65 Encoder PPR 3-19

Index-13
Encoder Speed 3-11 Fld Reg Kp Base 3-14

Encoder State 3-50 Fld Weaken Ratio 3-15
Fast Stop Status 3-50 FldLoss Flt Cfg 3-54
Fast Stop Time 3-31 Flying Start En 3-27
Fault 1 Code 3-53 Force Min Field 3-15
Fault 1 Time 3-53 Freeze Ramp 3-30
Fault 10 Code 3-53 Friction 3-21
Fault 10 Time 3-53 Gear Box Ratio 3-40
Fault 2 Code 3-53 I Reg Error 3-20
Fault 2 Time 3-53 Inertia 3-21
Fault 3 Code 3-53 Inertia C Filter 3-20
Fault 3 Time 3-53 InertiaCompAct 3-28
Fault 4 Code 3-53 InertiaCompVar 3-28
Fault 4 Time 3-53 Initial Diameter 3-43
Fault 5 Code 3-53 Int Acc Calc En 3-43
Fault 5 Time 3-53 Inversion In 1 3-67
Fault 6 Code 3-53 Inversion In 10 3-67
Fault Arm Amps 3-53 Inversion In 7 3-67
Fault Clear 3-52 Inversion In 8 3-67
Fault Clr Mask 3-58 Inversion In 9 3-67
Fault Clr Mode 3-52 Inversion Out 1 3-70
Fault Clr Owner 3-59 Inversion Out 2 3-70
Fault Field Amps 3-53 Inversion Out 3 3-70
Fault Speed 3-53 Inversion Out 4 3-70
Fault Voltage 3-53 Inversion Out 5 3-70
FaultCode 3-13 Inversion Out 6 3-70
Fdbk Device Type 3-19 Inversion Out 7 3-70
Feed Fwd PID 3-37 Inversion Out 8 3-70
Field Current 3-12 Inversion Relay1 3-71
Field Current Pct 3-12 Inversion Relay2 3-70
Field Econ Delay 3-16 Jog Mask 3-58
Field Economy En 3-16 Jog Off Delay 3-24
Field Mode Sel 3-15 Jog Owner 3-59
Field Reg Enable 3-15 Jog Ramp Time 3-29
Filt Torq Cur 3-19 Jog Speed 3-23
Filt TorqCur Pct 3-12 Jog TW Enable 3-45
Final Diameter 3-43 Jog TW Speed 3-45
Fld Const 40 Pct 3-16 Last Stop Source 3-52
Fld Const 70 Pct 3-16 Line Accel Pct 3-43
Fld Const 90 Pct 3-16 Line Decel Pct 3-43
Fld Current Pct 3-12 Line FastStp Pct 3-43
Fld Reg Ki 3-14 Line Spd Gain 3-41
Fld Reg Ki Base 3-15 Line Spd Source 3-44
Fld Reg Kp 3-14 Line Spd Thresh 3-41

Index-14
Line Speed Pct 3-41 PI Central v3 3-34

Load Comp 3-31 PI Central vs0 3-35
Local Mask 3-59 PI Central vs1 3-35
Local Owner 3-59 PI Init Intgl Gn 3-36
Lock Speed Integ 3-26 PI Init Prop Gn 3-35
Logic Mask 3-2, 3-58, 3-60 PI integr freeze 3-35
Logic Mask Act 3-60 PI Integral Gain 3-34
Man Ref Preload 3-46 PI Lower Limit 3-35
Materl Width Pct 3-42 PI Output 3-34
Max Deviation 3-40 PI Prop Gain PID 3-34
Max Diameter 3-41 PI Steady Thrsh 3-34
Max Feedback Spd 3-14 PI Upper Limit 3-35
Max Fld Curr Pct 3-15 PID Accel Time 3-38
Max Ref Speed 3-14 PID Clamp 3-37
Max Speed Fwd 3-23 PID Decel Time 3-38
Max Speed Rev 3-23 PID Error 3-37
Maximum Speed 3-23 PID Error Gain 3-39
Min Fld Curr Pct 3-15 PID Feedback 3-37
Min Speed Fwd 3-23 PID Output 3-37
Min Speed Rev 3-23 PID Output Scale 3-37
Minimum Diameter 3-40 PID Output Sign 3-37
Minimum Speed 3-23 PID Setpoint 0 3-37
MOP Accel Time 3-29 PID Setpoint 1 3-37
MOP Dec Active 3-49 PID Setpoint Sel 3-37
MOP Decel Time 3-29 PID Source 3-38
MOP Inc Active 3-49 PID Source Gain 3-38
MOP Mask 3-58 PID Steady Delay 3-36
MOP Owner 3-59 PID Target 3-38
MOP Select 3-46 Port Mask Act 3-61
Nom Mtr Arm Amps 3-14 Powerup Delay 3-32
Nom Mtr Fld Amps 3-14 Preset Speed 1 3-23
Offs Accel Time 3-44 Preset Speed 2 3-23
Opening Delay 3-32 Preset Speed 3 3-23
Out Volt Level 3-16 Preset Speed 4 3-23
Output Power 3-13 Preset Speed 5 3-23
Output Voltage 3-13 Preset Speed 6 3-23
OverCurrent Thr 3-54 Preset Speed 7 3-23
OverTemp Flt Cfg 3-53 Ramp Delay 3-29
OverVolt Flt Cfg 3-53 Ramp In 3-11
Param Access Lvl 3-46 Ramp In Pct 3-11
PD Deriv Filter 3-36 Ramp In Zero En 3-32
PD Deriv Gain 1 3-36 Ramp Out 3-11
PD Deriv Gain 2 3-36 Ramp Out Pct 3-11
PD Deriv Gain 3 3-36 Ramp Select 0 3-50
PD Output PID 3-36 Ramp Select 1 3-50
PD Prop Gain 1 3-36 Ramp Type Select 3-29
PD Prop Gain 2 3-36 Rated Motor Volt 3-14
PD Prop Gain 3 3-36 Real FF PID 3-36
PI Central v sel 3-35 Ref Line Spd 3-45
PI Central v1 3-34 Ref Spd Source 3-45
PI Central v2 3-34 Ref Speed Gain 3-45

Index-15
Ref Zero Level 3-25 Scale5 Div 3-39

Reference Mask 3-58 Scale5 In Abs 3-40
Reference Owner 3-59 Scale5 In Max 3-39
Relay Out 1 Sel 3-70 Scale5 In Min 3-39
Relay Out 2 Sel 3-70 Scale5 In Off 3-40
Reset Defaults 3-46 Scale5 Input 3-39
Reset Fld Curve 3-16 Scale5 Mul 3-39
Roll Diameter 3-41 Scale5 Out Off 3-40
S Curve Accel 1 3-30 Scale5 Output 3-39
S Curve Accel 2 3-30 Scale6 Div 3-39
S Curve Decel 1 3-30 Scale6 In Abs 3-40
S Curve Decel 2 3-30 Scale6 In Max 3-39
S Curve Time 3-29 Scale6 In Min 3-39
Save HIM Ref 3-46 Scale6 In Off 3-40
Save MOP Ref 3-46 Scale6 Input 3-39
Scale1 Div 3-39 Scale6 Mul 3-39
Scale1 In Abs 3-40 Scale6 Out Off 3-40
Scale1 In Max 3-39 Scale6 Output 3-39
Scale1 In Min 3-39 Set Fld Curve 3-16
Scale1 In Off 3-40 Software Version 3-13
Scale1 Input 3-39 Spd 0 Trip Delay 3-31
Scale1 Mul 3-39 Spd Draw Out Pct 3-12
Scale1 Out Off 3-40 Spd Fdbk Control 3-19
Scale1 Output 3-39 Spd Fdbk Error 3-19
Scale2 Div 3-39 Spd Fdbk Filter 3-27
Scale2 In Abs 3-40 Spd Limit Active 3-47
Scale2 In Max 3-39 Spd Loss Flt Cfg 3-54
Scale2 In Min 3-39 Spd Match Acc 3-44
Scale2 In Off 3-40 Spd Match Compl 3-44
Scale2 Input 3-39 Spd Match Dec 3-44
Scale2 Mul 3-39 Spd Match Gain 3-44
Scale2 Out Off 3-40 Spd match torque 3-45
Scale2 Output 3-39 Spd Ref Zero En 3-26
Scale3 Div 3-39 Spd Reg Autotune 3-21
Scale3 In Abs 3-40 Spd Reg Ki 3-24
Scale3 In Max 3-39 Spd Reg Ki Base 3-24
Scale3 In Min 3-39 Spd Reg Ki Outpt 3-24
Scale3 In Off 3-40 Spd Reg Kp 3-24
Scale3 Input 3-39 Spd Reg Kp Base 3-24
Scale3 Mul 3-39 Spd Reg Kp Outpt 3-24
Scale3 Out Off 3-40 Spd Reg Out Pct 3-12
Scale3 Output 3-39 Spd Select 0 3-49
Scale4 Div 3-39 Spd Select 1 3-50
Scale4 In Abs 3-40 Spd Select 2 3-50
Scale4 In Max 3-39 Spd Tune Inertia 3-21
Scale4 In Min 3-39 Spd Up Gain Pct 3-27
Scale4 In Off 3-40 Spd Zero I En 3-26
Scale4 Input 3-39 Spd Zero P En 3-26
Scale4 Mul 3-39 Spd Zero P Gain 3-26
Scale4 Out Off 3-40 SpdFuncSelect 3-28
Scale4 Output 3-39 SpdReg FB Bypass 3-19

Index-16
SpdReg Ki Bypass 3-27 Torq Current Pct 3-43

SpdReg Kp Bypass 3-27 Torq Limit Type 3-31
SpdTune Friction 3-21 Torq Red CurLim 3-31
Speed Demand En 3-45 Torque Const 3-20
Speed Draw Out 3-12 Torque Negative 3-47
Speed Feedback 3-11 Torque Positive 3-47
Speed Feedback Pct 3-11 Torque Reduction 3-17
Speed Match 3-43 Torque Ref 3-17
Speed Ramp En 3-30 Torque Winder En 3-44
Speed Ratio 3-24 Trim Ramp 3-24
Speed Ref A 3-11 Trim Ramp Pct 3-24
Speed Ref A Pct 3-11 Trim Speed 3-24
Speed Ref B 3-11 Trim Speed Pct 3-24
Speed Ref B Pct 3-11 Trim Torque 3-17
Speed Ref Out 3-11 TrqTpr_Enable 3-18
Speed Ref Out Pct 3-11 TrqTpr_Lim0 3-18
Speed Reg En 3-26 TrqTpr_Lim1 3-18
Speed Reg In 3-11 TrqTpr_Lim2 3-18
Speed Reg In Pct 3-11 TrqTpr_Lim3 3-18
Speed Thresh Neg 3-25 TrqTpr_Lim4 3-18
Speed Thresh Pos 3-25 TrqTpr_Spd 3-18
Speed Threshold 3-49 TstGen Amplitude 3-22
Speed Tune Dir 3-21 TstGen Frequency 3-22
Speed Tune Ki 3-21 TstGen Offset 3-22
Speed Tune Kp 3-21 TstGen Output 3-22
Speed Up Base 3-27 UnderVolt Thresh 3-54
Speed Up Filter 3-27 UserDefined0 3-55
Speed Zero Delay 3-25 UserDefined1 3-55
Speed Zero Level 3-25 UserDefined10 3-55
Start At Powerup 3-32 UserDefined11 3-55
Start Inhibits 3-52 UserDefined12 3-55
Start Mask 3-58 UserDefined13 3-55
Start Owner 3-59 UserDefined14 3-55
Static F Zero 3-45 UserDefined15 3-55
Static Friction 3-42 UserDefined2 3-55
Status1 at Fault 3-52 UserDefined3 3-55
Status2 at Fault 3-52 UserDefined4 3-55
Stop Owner 3-59 UserDefined5 3-55
Taper Enable 3-43 UserDefined6 3-55
TaskLoad 1 ms 3-51 UserDefined7 3-55
TaskLoad 8 ms 3-51 UsrDefBitWrdA 3-55
TB Manual Ref 3-24 UsrDefBitWrdA0 3-56
Tension Reduct 3-43 UsrDefBitWrdA1 3-56
Tension Ref 3-43 UsrDefBitWrdA10 3-56
Tension Scale 3-43 UsrDefBitWrdA11 3-56
TestPoint Data 3-51 UsrDefBitWrdA12 3-56
TestPoint Sel 3-51 UsrDefBitWrdA13 3-56
Threshold Delay 3-25 UsrDefBitWrdA14 3-56
Time AccDec Min 3-43 UsrDefBitWrdA15 3-56

Index-17
UsrDefBitWrdA2 3-56 PD Prop Gain 1 3-36

UsrDefBitWrdA5 3-56
PE Ground 1-12
UsrDefBitWrdA6 3-56
UsrDefBitWrdA7 3-56 PE Ground Terminal
Location - Frame A 1-20
UsrDefBitWrdA8 3-56
Location - Frame B 1-20
UsrDefBitWrdA9 3-56
Location - Frame C 1-21
UsrDefBitWrdB 3-57
UsrDefBitWrdB0 3-57 Wire Sizes 1-22
UsrDefBitWrdB1 3-57 Peripheral Devices, Viewing Parameters of
UsrDefBitWrdB10 3-57 B-4
UsrDefBitWrdB11 3-57 PI Central v sel 3-35
UsrDefBitWrdB12 3-57 PI Central v1 3-34
UsrDefBitWrdB15 3-57
PI Central vs0 3-35
UsrDefBitWrdB2 3-57
PI Central vs1 3-35
UsrDefBitWrdB3 3-57
UsrDefBitWrdB4 3-57 PI Control Group 3-34, 3-35
UsrDefBitWrdB5 3-57 PI Init Intgl Gn 3-36
UsrDefBitWrdB6 3-57 PI Init Prop Gn 3-35
UsrDefBitWrdB7 3-57 PI integr freeze 3-35
UsrDefBitWrdB8 3-57
PI Integral Gain 3-34
UsrDefBitWrdB9 3-57
PI Lower Limit 3-35
UsrDsplyDiv0 3-54
UsrDsplyMult0 3-54 PI Output 3-34
UsrValDiv1 3-55 PI Prop Gain PID 3-34
UsrValMult1 3-54 PI Steady Thrsh 3-34
Variable J Comp 3-42 PI Upper Limit 3-35
Viewing B-5 PID Accel Time 3-38
W Offset 3-44
PID Clamp 3-37
W Reference 3-45
PID Control Group 3-36, 3-37, 3-38, 3-39
W Target 3-44
Winder Side 3-44 PID Decel Time 3-38
Winder Type 3-43 PID Error 3-37
Write Mask Act 3-61 PID Error Gain 3-39
Write Mask Cfg 3-61 PID Feedback 3-37
Z Capture Pos En 3-20 PID Function
Z Captured Pos 3-20
Configuring a Feedback Signal C-10
Z Channel Enable 3-20 Configuring a Line Speed Signal C-9
Zero Ramp Input 3-30 Configuring a Tension Set Point Signal
Zero Ramp Output 3-30 C-12
Zero Torque 3-17
PID Output 3-37
PD Control Group 3-36
PID Output Scale 3-37
PD Deriv Filter 3-36
PID Output Sign 3-37
PD Deriv Gain 1 3-36
PID Setpoint 0 3-37
PID Setpoint 1 3-37
PID Setpoint Sel 3-37
PD Output PID 3-36
PID Source 3-38

Index-18
PID Source Gain 3-38 Programmable Controller Configurations

PID Steady Delay 3-36 A-5
PID Target 3-38 Programming 3-1
Port 1 Adapter Fault 4-5
Port 1 DPI Loss Fault 4-6 R
Port 2 Adapter Fault 4-5 Ramp Delay 3-29
Port 2 DPI Loss Fault 4-6 Ramp In 3-11
Port 3 Adapter Fault 4-5 Ramp In Pct 3-11
Port 3 DPI Loss Fault 4-6 Ramp In Zero En 3-32
Port 4 Adapter Fault 4-5 Ramp Out 3-11
Port 4 DPI Loss Fault 4-6 Ramp Out Pct 3-11
Port 5 Adapter Fault 4-5 Ramp Rates Group 3-29, 3-30
Port 5 DPI Loss Fault 4-6 Ramp Select 0 3-50
PORT LED 4-2 Ramp Select 1 3-50
Port Mask Act 3-61 Ramp Type Select 3-29
Potentiometer, Wiring 1-37 Rated Motor Volt 3-14
Power Circuit Real FF PID 3-36
Fuses 1-13 Recommended AC Input Contactors A-17
Protection 1-13
Recommended AC Input Line Reactors
Power Circuit Protection A-17
Fuse Designations - Frame A A-7
Recommended DC Output Contactors A-19
Fuse Designations - Frame B A-7
Recommended Dynamic Brake Resistors
Power Failure Fault 4-6 A-19
Power Feeder Ground 1-13 Ref Line Spd 3-45
Power Wiring 1-15 Ref Spd Source 3-45
AC Input Contactor 1-17
Ref Speed Gain 3-45
Armature Converter Terminals 1-20
Ref Zero Level 3-25
Armature Output Terminals 1-20
Control Circuit Terminals 1-28 Reference Config Group 3-46
DC Output Contactor 1-18 Reference Mask 3-58
DC Output Contactor and a Dynamic Reference Owner 3-59
Brake 1-19 Regulators
Diagrams 1-17 Fine Tuning C-25
Field Input Terminals 1-23
Relay Out 1 Sel 3-70
Field Output Terminals 1-23
Relay Out 2 Sel 3-70
Motor Thermistor Terminals 1-25
Normally Open Contact Terminals 1-25 Relay Output Option Definitions 3-69
Powerup Delay 3-32 Relay Outputs 1-25
Preferences, Setting HIM B-5 Removing drive covers 1-7
Preset Speed 1 3-23 Frame B and C 1-8
Preset Speed 2 3-23 Removing the HIM B-6
Preset Speed 3 3-23 Reset Defaults 3-46
Preset Speed 4 3-23 Reset Fld Curve 3-16
Preset Speed 5 3-23 Reset to Defaults B-4
Preset Speed 6 3-23 Restart Modes Group 3-32
Preset Speed 7 3-23 Roll Diameter 3-41

Index-19
S Scale3 Output 3-39

S Curve Accel 1 3-30 Scale4 Div 3-39
S Curve Accel 2 3-30 Scale4 In Abs 3-40
S Curve Decel 1 3-30 Scale4 In Max 3-39
S Curve Decel 2 3-30 Scale4 In Min 3-39
S Curve Time 3-29 Scale4 In Off 3-40
S.M.A.R.T. List Screen Scale4 Input 3-39
Accessing B-2 Scale4 Mul 3-39
Using B-2 Scale4 Out Off 3-40
S14 Switch 1-24 Scale4 Output 3-39
Safety Ground 1-12 Scale5 Div 3-39
SA-SB Terminal Block Scale5 In Abs 3-40
Location 1-29 Scale5 In Max 3-39
Save HIM Ref 3-46 Scale5 In Min 3-39
Save MOP Ref 3-46 Scale5 In Off 3-40
Saving Data B-4 Scale5 Input 3-39
Scale Blocks function C-16 Scale5 Mul 3-39
Scale Blocks Group 3-39, 3-40 Scale5 Out Off 3-40
Scale1 Div 3-39 Scale5 Output 3-39
Scale1 In Abs 3-40 Scale6 Div 3-39
Scale1 In Max 3-39 Scale6 In Abs 3-40
Scale1 In Min 3-39 Scale6 In Max 3-39
Scale1 In Off 3-40 Scale6 In Min 3-39
Scale1 Input 3-39 Scale6 In Off 3-40
Scale1 Mul 3-39 Scale6 Input 3-39
Scale1 Out Off 3-40 Scale6 Mul 3-39
Scale1 Output 3-39 Scale6 Out Off 3-40
Scale2 Div 3-39 Scale6 Output 3-39
Scale2 In Abs 3-40 Security Group 3-60, 3-61
Scale2 In Max 3-39 Set Fld Curve 3-16
Scale2 In Min 3-39 Setting Preferences
Scale2 In Off 3-40 HIM B-5
Scale2 Input 3-39 Signal Wire 1-26, F-1
Scale2 Mul 3-39 Signal Wire Sizes 1-35
Scale2 Out Off 3-40 Software Version 3-13
Scale2 Output 3-39 Sourcing Digital Output, Wiring 1-39
Scale3 Div 3-39 Spd 0 Trip Delay 3-31
Scale3 In Abs 3-40 Spd Draw Out Pct 3-12
Scale3 In Max 3-39 Spd Fdbk Control 3-19
Scale3 In Min 3-39 Spd Fdbk Error 3-19
Scale3 In Off 3-40 Spd Fdbk Filter 3-27
Scale3 Input 3-39 Spd Limit Active 3-47
Scale3 Mul 3-39 Spd Loss Flt Cfg 3-54
Scale3 Out Off 3-40 Spd Match Acc 3-44

Index-20
Spd Match Compl 3-44 Speed Ref A Pct 3-11

Spd Match Dec 3-44 Speed Ref B 3-11
Spd Match Gain 3-44 Speed Ref B Pct 3-11
Spd match torque 3-45 Speed Ref Out 3-11
Spd Ref Zero En 3-26 Speed Ref Out Pct 3-11
Spd Reg Autotune 3-21 Speed Reference Control C-13
Spd Reg Ki 3-24 Speed Reference Sources
Spd Reg Ki Base 3-24 Auto C-13
Spd Reg Ki Outpt 3-24 Manual C-13
Spd Reg Kp 3-24 Speed References Group 3-24
Spd Reg Kp Base 3-24 Speed Reg En 3-26
Spd Reg Kp Outpt 3-24 Speed Reg In 3-11
Spd Reg Out Pct 3-12 Speed Reg In Pct 3-11
Spd Select 0 3-49 Speed Regulation Functions C-17
Adaptive Speed Regulator C-17
Spd Select 1 3-50
Speed Draw C-23
Spd Select 2 3-50
Speed Threshold Indicators C-20
Spd Tune Inertia 3-21 Speed Up C-20
Spd Up Gain Pct 3-27 Speed Zero C-22
Spd Zero I En 3-26 Speed Regulator
Spd Zero P En 3-26 Fine Tuning C-29
Spd Zero P Gain 3-26 Speed Regulator Group 3-24
SpdFuncSelect 3-28 Speed Thresh Neg 3-25
SpdReg FB Bypass 3-19 Speed Thresh Pos 3-25
SpdReg Ki Bypass 3-27 Speed Threshold 3-49
SpdReg Kp Bypass 3-27 Speed Threshold Indicators C-20
SpdTune Friction 3-21 Speed Tune Aborted Fault 4-6
Specifications Speed Tune Current Limit Fault 4-6
Agency Certification A-1 Speed Tune Dir 3-21
Control A-2 Speed Tune Friction Low Fault 4-6
Electrical A-2
Speed Tune Ki 3-21
Environment A-1
Speed Tune Kp 3-21
Protection A-1
Speed Tune Load High Fault 4-6
Speed Command File 3-23
Speed Up Base 3-27
Speed Demand En 3-45
Speed Up Filter 3-27
Speed Draw Function C-23
Speed Up Function C-20
Speed Draw Out 3-12
Speed Zero Delay 3-25
Speed Feedback 3-11
Speed Zero Function C-22
Speed Feedback Group 3-19, 3-20
Speed Zero Level 3-25
Speed Feedback Pct 3-11
Speed Zero Logic C-22
Speed Match 3-43
Standard I/O Terminal Block Designations
Speed Meters Group 3-11, 3-12
1-36, 1-37
Speed Pot 1-37
Start At Power Up Alarm 4-9
Speed Ramp En 3-30
Start At Powerup 3-32
Speed Ratio 3-24
Start At Powerup Configuration C-24
Speed Ref A 3-11
Start Inhibits 3-52

Index-21
Start Mask 3-58 TestPoint Data 3-51

Start Owner 3-59 TestPoint Sel 3-51
Starting Up a Drive 2-1 Testpoints 4-14
Static F Zero 3-45 Thermal Switch
Static Friction 3-42 Configuration 1-26
Status1 at Fault 3-52 Thermistors (PTC)
Status2 at Fault 3-52 Configuration 1-26
Stop Modes Group 3-31, 3-32 Threshold Delay 3-25
Stop Owner 3-59 Time AccDec Min 3-43
Storing the Drive Torq Attributes Group 3-16, 3-17, 3-18, 3-19
Altitude p-1 Torq Current Pct 3-43
Humidity Level p-1 Torq Limit Type 3-31
Temperature p-1 Torq Red CurLim 3-31
STS LED Torque Const 3-20
Green, Flashing 4-2 Torque Negative 3-47
Green, Steady 4-2
Torque Positive 3-47
Red, Flashing 4-2
Torque Reduction 3-17
Red, Steady 4-2
Yellow, Flashing - Drive Running 4-2 Torque Ref 3-17
Yellow, Flashing - Drive Stopped 4-2 Torque Reference Source C-14
Yellow, Steady - Drive Running 4-2 Torque Winder En 3-44
Surrounding Air Temperature 1-2 Trim Ramp 3-24
Trim Ramp Pct 3-24
T Trim Speed 3-24
Tachometer Ground 1-13 Trim Speed Pct 3-24
Taper Enable 3-43 Trim Torque 3-17
TaskLoad 1 ms 3-51 Troubleshooting 4-1
TaskLoad 2 ms 3-51 TrqTpr_Enable 3-18
TaskLoad 32 ms 3-51 TrqTpr_Lim0 3-18
TaskLoad 8 ms 3-51 TrqTpr_Lim1 3-18
TB Manual Ref 3-24 TrqTpr_Lim2 3-18
Tension Reduct 3-43 TrqTpr_Lim3 3-18
Tension Ref 3-43 TrqTpr_Lim4 3-18
Tension Scale 3-43 TrqTpr_Spd 3-18
Terminal Blocks TstGen Amplitude 3-22
Armature Converter - Frame A 1-20 TstGen Frequency 3-22
Armature Converter - Frame B 1-20 TstGen Offset 3-22
Armature Converter - Frame C 1-21 TstGen Output 3-22
DC Analog Tachometer 1-42 Tuning the Field Current Curve C-33
Encoder 1-40
Field Circuit - Frame A 1-23
Field Circuit - Frame B 1-23 U
Field Circuit - Frame C 1-24 UnderVolt Thresh 3-54
I/O Converter Board G-2 User Defined Group 3-54, 3-55, 3-56, 3-57
I/O Expansion Board F-2
User Sets B-4
Standard I/O 1-36, 1-37
UserDefined0 3-55
Test Generator Group 3-22

Index-22
UserDefined1 3-55 UsrDefBitWrdB15 3-57

UserDefined4 3-55 UsrDsplyDiv0 3-54
UserDefined5 3-55 UsrDsplyMult0 3-54
UserDefined6 3-55 UsrValDiv1 3-55
UserDefined7 3-55 UsrValMult1 3-54
UserDefined8 3-55 Utility File 3-46
UserDefined9 3-55
Using a PTC 1-26 V
Using a Thermal Switch 1-25
Variable J Comp 3-42
Using a Thermistor 1-25
Viewing Parameters B-5
Using the Test Generator C-25
Voltage Regulator
UsrDefBitWrdA 3-55 Fine Tuning C-31
UsrDefBitWrdA0 3-56
UsrDefBitWrdA1 3-56
W
UsrDefBitWrdA10 3-56
W Offset 3-44
W Reference 3-45
W Target 3-44
Watts Loss Data A-4
Winder Functions Group 3-42, 3-43, 3-44,
3-45
UsrDefBitWrdA2 3-56
Winder Side 3-44
UsrDefBitWrdA3 3-56
Winder Type 3-43
UsrDefBitWrdA4 3-56
Wire
UsrDefBitWrdA5 3-56 Signal 1-26, 1-35, F-1
UsrDefBitWrdA6 3-56 Wire Sizes
UsrDefBitWrdA7 3-56 Armature Terminals 1-22
UsrDefBitWrdA8 3-56 Field Terminals 1-24
UsrDefBitWrdA9 3-56 PE Ground Terminal 1-22
UsrDefBitWrdB 3-57
UsrDefBitWrdB0 3-57
UsrDefBitWrdB1 3-57

Index-23
Wiring 1-1
2-Wire Control Non-Reversing 1-38
2-Wire Control Reversing 1-39
3-Wire Control 1-39
Analog Input Bipolar Speed Reference
1-38
Analog Input Unipolar Speed Reference
1-38
Analog Output Bipolar Signal 1-38
Enable Input 1-38
Encoder 1-41
Joystick 1-37
Potentiometer 1-37
Sourcing Digital Output 1-39
Write Mask Act 3-61
Write Mask Cfg 3-61
Z
Z Capture Pos En 3-20
Z Captured Pos 3-20
Z Channel Enable 3-20
Zero Ramp Input 3-30
Zero Ramp Output 3-30
Zero Torque 3-17

Index-24

U.S. Allen-Bradley Drives Technical Support - Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: support@drives.ra.rockwell.com, Online: www.ab.com/support/abdrives
www.rockwellautomation.com
Power, Control and Information Solutions Headquarters

Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204 USA,Tel: (1) 414.382.2000, Fax: (1) 414.382.4444
Europe/Middle East/Africa: Rockwell Automation, Vorstlaan/Boulevard du Souverain 36, 1170 Brussels, Belgium,Tel: (32) 2 663 0600, Fax: (32) 2 663 0640
Asia Pacific: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong,Tel: (852) 2887 4788, Fax: (852) 2508 1846
Publication 20P-UM001C-EN-P - July 2008

Supersedes 20P-UM001B-EN-P -October 2007 and 20P-DU001A-EN-P Copyright © 2008 Rockwell Automation, Inc. All rights reserved. Printed in USA.

PowerFlex700DC en

Uploaded by

Copyright:

Available Formats

PowerFlex700DC en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PowerFlex700DC en

Uploaded by

Copyright:

Available Formats

PowerFlex® Digital DC Drive

Firmware Version 1.006 - 2.001

WARNING: Identifies information about practices or

Important: Identifies information that is critical for successful application and

ATTENTION: Identifies information about practices or

Shock Hazard labels may be located on or inside the equipment

Burn Hazard labels may be located on or inside the equipment

PowerFlex Digital DC Drive User Manual

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

The information below summarizes the changes to the PowerFlex Digital

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Summary of Manual Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . soc-i

Chapter 1 Installation and Wiring

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

I/O Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32

Chapter 2 Drive Start Up

Chapter 3 Programming and Parameters

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Appendix A Supplemental Drive Information

Appendix B HIM Overview

Appendix C Application Notes

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Speed Regulation Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-17

Appendix D Control Block Diagrams

Appendix E Installing a Communication Adapter

Appendix F Optional Analog and Digital I/O Expansion Circuit Board

Appendix G Optional 115V AC to 24V DC I/O Converter Circuit Board

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

• Place where the ambient temperatures do not exceed -25° C (-13° F) or

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Cat No. 20P41AD4P1RA0NNN

For Allen-Bradley Drives Technical Support:

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

– Parameter Names will appear in [brackets].

– Display Text will appear in “quotes.” For example: “Enabled.”

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Motor Operation 020 5 20 A 10

Code Type 029 7.5 29 A 10 h

Input Type 146 40 146 B 20 Q No Yes

Code Type 180 50 180 B 20

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Installation and Wiring

This chapter provides information on mounting and wiring the PowerFlex

ATTENTION: The following information is merely a guide for

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Mounting Considerations Operating Conditions and Temperatures

Minimum Mounting Clearances

150 mm (6.0 in.)

150 mm (6.0 in.)

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

ATTENTION: Remove all loose packing materials, including

Figure 1.2 Frame A Approximate Dimensions

Table 1.A Frame A Weights

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Figure 1.3 Frame B Approximate Dimensions

Table 1.B Frame B Weights

PowerFlex Digital DC Drive User Manual - Publication 20P-UM001C-EN-P - July 2008

Figure 1.4 Frame C Approximate Dimensions

Table 1.C Frame C Weights