TECHNICAL REPORT CEN/TR 17052

RAPPORT TECHNIQUE
TECHNISCHER BERICHT January 2017

ICS 91.080.10

English Version

Guidelines on implementing EN 1090-1:2009+A1:2011,

Execution of steel structures and aluminium structures -
Part 1: Requirements for conformity assessment of
structural components
Lignes directrices pour l'application de l'EN 1090- Leitfaden für die Umsetzung von EN 1090-
1:2009+A1:2011, Exécution des structures en acier et 1:2009+A1:2011, Ausführung von Stahlbetonwerken
des structures en aluminium - Partie 1: Exigences pour und Aluminiumtragwerken - Teil 1:
l'évaluation de la conformité des éléments structuraux Konformitãtsnachweisverfahren für tragende Bauteile

This Technical Report was approved by CEN on 11 December 2016. It has been drawn up by the Technical Committee CEN/TC
135.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 17052:2017 E
worldwide for CEN national Members.
CEN/TR 17052:2017 (E)

Contents Page

European foreword....................................................................................................................................................... 3
Introduction .................................................................................................................................................................... 4
1 Scope .................................................................................................................................................................... 5
2 Normative references .................................................................................................................................... 5
3 Terms and definitions ................................................................................................................................... 5
4 Conditions necessary for construction products to be covered by the scope of
EN 1090-1 ........................................................................................................................................................... 6
5 Clarification ....................................................................................................................................................... 6
5.1 General ................................................................................................................................................................ 6
5.2 Condition 1 – The product fulfils the requirements of EN 1090-2 or EN 1090-3 ..................... 6
5.3 Condition 2 – The product is a structural construction product within the meaning of
the Construction Products Regulation (EU) 305/2011 ..................................................................... 6
5.3.1 Condition 2a - The product is intended to be incorporated in a permanent manner in
construction works......................................................................................................................................... 6
5.3.2 Condition 2b - The product has a structural function in relation to the construction
work ..................................................................................................................................................................... 7
5.4 Condition 3 – The product is not covered by another European technical
specification ...................................................................................................................................................... 8
5.4.1 General ................................................................................................................................................................ 8
5.4.2 Construction products covered by another harmonized standard .............................................. 8
5.4.3 Construction products covered by an ETA .......................................................................................... 10
Annex A (informative) Products covered by EN 1090-1 ............................................................................. 11
Annex B (informative) Products not covered by EN 1090-1 ...................................................................... 14

2
 CEN/TR 17052:2017 (E)

European foreword

This document (CEN/TR 17052:2017) has been prepared by Technical Committee CEN/TC 135
“Execution of steel structures and aluminium structures”, the secretariat of which is held by SN.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.

3
CEN/TR 17052:2017 (E)

Introduction

The scope of the standard EN 1090-1:2009+A1:2011 “Execution of steel structures and aluminium
structures: Part 1: Requirements for conformity assessment of structural components” is very broad
and prompted the European Commission to publish on their website under the category “Frequently
Asked Questions (FAQ) on the Constructions Products Regulation” a set of conditions for identifying
when a steel or aluminium product falls within its scope and an indicative, non-exhaustive list of
products that are not covered by the scope of EN 1090-1:2009+A1:2011.
This document aims to clarify in addition to the answers given on the European Commission’s FAQ
website the scope of EN 1090-1:2009+A1:2011.

4
 CEN/TR 17052:2017 (E)

1 Scope
The scope of EN 1090-1:2009+A1:2011 states that the standard covers structural components and kits
which are referred to as structural construction products in this document. This document gives
information that clarifies when a structural construction product is covered by the scope of
EN 1090-1:2009+A1:2011 and lists examples of products covered and not covered.

2 Normative references
The following documents, in whole or in part, are referenced in this document and are indispensable for
its application. For dated references, only the edition cited applies. For undated references, the latest
edition of the referenced document (including any amendments) applies.
EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements
for conformity assessment of structural components

EN 1090-2:2008+A1:2011, Execution of steel structures and aluminium structures - Part 2: Technical

requirements for steel structures

EN 1090-3:2008, Execution of steel structures and aluminium structures - Part 3: Technical requirements
for aluminium structures

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.
3.1
Harmonized Standard for construction products (hEN)
standard adopted by one of the European standardisation bodies listed in Annex I to Directive
98/34/EC, on the basis of a request issued by the Commission, in accordance with Article 6 of that
Directive, and which has been cited in the Official Journal of the European Union (OJEU) as a
harmonized standard under the Construction Products Regulation (EU) 305/2011/EC

3.2
European Assessment Document (EAD)
document on the basis of the EU Construction Products Regulation EU 305/2011 adopted by the
organisation of Technical Assessment Bodies for the purposes of issuing European Technical
Assessments

3.3
European Technical Assessment (ETA)
documented assessment of the performance of a construction product in relation to its essential
characteristics, in accordance with the respective European Assessment Document

3.4
European Technical Approval (ETA)
favourable technical assessment of the fitness for use of a product for an intended use on the basis of
the Construction Products Directive (89/106/EEC), based on fulfilment of the essential requirements
for construction works for which the product is used

Note 1 to entry: According to EU 305/2011/EC, article 66, 4) European technical approvals may be used as
European Technical Assessments throughout the period of validity of those approvals.

5
CEN/TR 17052:2017 (E)

3.5
European Technical Approval Guidelines (ETAG)
guideline for the issuing of a European Technical Approval on the basis of the EU Construction Products
Directive (89/106/EEC)

Note 1 to entry: According to EU 305/2011/EC, article 66, 3) ETAGs may be used as EADs.

4 Conditions necessary for construction products to be covered by the scope of

EN 1090-1
Construction products are covered by the scope of EN 1090-1:2009+A1:2011 when all the following
conditions are satisfied:
Condition 1: The product fulfils the requirements of EN 1090-2 or EN 1090-3
Condition 2: The product is a structural construction product within the meaning of the
Construction Products Regulation (EU) 305/2011 which means:
Condition 2a: The product is intended to be incorporated in a permanent manner in construction
works (buildings or civil engineering works), and
Condition 2b: The product has a structural function in relation to the construction work (i.e. its
failure will affect the satisfaction of Basic Requirement 1 and subclause a) of Basic Requirement 2 as
detailed in 5.3.2 and Annex I of the Construction Products Regulation (EU) 305/2011/EC).
Condition 3: This European Standard does not apply to construction products covered by another
European technical specification (e.g. a specific harmonized standard (hEN) or a European Technical
Approval or European Technical Assessment (ETA)).

5 Clarification
5.1 General

In this clause further clarification of the conditions of Clause 4 is given.

Structural construction products are part of a loadbearing construction which is an organized assembly
of connected parts designed to provide mechanical resistance and stability to the works. A way of
identifying a structural construction product is to ask the question: “If the product is removed does its
removal affect the strength and stability of the structure or a part of the structure?”. If the answer to this
question is yes then the product is a structural construction product, see also
EN 1090-1:2009+A1:2011, 3.1.9.
For indicative, non-exhaustive lists of products covered and not covered by the scope of
EN 1090-1:2009+A1:2011, see Annex A and Annex B of this document.
5.2 Condition 1 – The product fulfils the requirements of EN 1090-2 or EN 1090-3

For a product to fall within the scope of EN 1090-1 the processes for its manufacture shall comply with
EN 1090-2 or EN 1090-3.
5.3 Condition 2 – The product is a structural construction product within the meaning of
the Construction Products Regulation (EU) 305/2011
5.3.1 Condition 2a - The product is intended to be incorporated in a permanent manner in
construction works

a) Incorporated in a permanent manner

6
 CEN/TR 17052:2017 (E)

Incorporation of a product in a permanent manner in the works means:

— that its removal reduces the performance capabilities of the works and

— that the dismantling or the replacement of the product are operations which involve
construction activities.

Typical construction products that are not incorporated in a permanent manner are scaffolding,
formwork, falsework and temporary edge protection.
b) Construction works

Construction works means buildings and civil engineering works (as for instance bridges).
Construction works are fixed to the ground. A construction work is to be regarded as “fixed to the
ground” when it is directly or indirectly connected to the ground or is supported by the ground.
Supported by the ground can be for instance by gravity or via piling.
5.3.2 Condition 2b - The product has a structural function in relation to the construction work

The product shall have a structural function in relation to the construction work (i.e. its failure will
affect the satisfaction of Basic Requirement 1 and subclause a) of Basic Requirement 2 as detailed in
Annex I of Regulation EU 305/2011).
These requirements are related to the mechanical resistance and stability of the “construction works”
including the safety in case of fire.
The requirements are:
The construction works shall be designed and built in such a way that the loadings that are liable to act
on them during their construction and use will not lead to any of the following (see Annex I of the
Construction Products Regulation (EU) 305/2011/EC):
a) Collapse of the whole or part of the work

b) Major deformations to an inadmissible degree

c) Damage to other parts of the construction works or to fittings or installed equipment as a result of
major deformation of the load-bearing construction;

d) Damage by an event to an extent disproportionate to the original cause.

In certain cases the construction works shall also be designed and built in such a way that in the event
of an outbreak of fire the load-bearing capacity of the construction can be assumed for a specific period
of time.
The “load-bearing construction” is a sub-set of the construction works and includes all those
construction products that contribute to the strength and stability and to the safety in case of fire of the
works. This includes both the main load-bearing elements (e.g. the frame, walls, columns, beams,
bracing, connectors, foundations) and the secondary load bearing elements (e.g. structural claddings,
purlins, decking).
Basic requirement No. 1 for construction works applies to the load bearing elements covering a wide
range of structural construction products. Examples of such products that may form part of the
construction work are given in Annex A.
NOTE Some of these elements might also be covered by Basic requirement No. 4 for construction works,
which is not addressed in EN 1090–1. Safety in use, in terms of unacceptable risks of accidents or damage in
service or operation, is concerned with Basic requirement No. 4 for construction works.

7
CEN/TR 17052:2017 (E)

5.4 Condition 3 – The product is not covered by another European technical

specification
5.4.1 General

The following types of technical specifications are meant here:

— harmonized standard or

— ETA (European Technical Assessment or still valid European technical approval).

5.4.2 Construction products covered by another harmonized standard

Construction products the performance of which can be assessed by other harmonized standard(s) do
not fall within the scope of EN 1090-1. There are many construction products that are assessed in
accordance with their own separate harmonized standard some of which are given in Table 1.
Table 1 — A list of harmonized standards for construction products that do not fall under the
scope of EN 1090–1

Harmonized Standard
EN 40–5 Lighting columns - Part 5: Requirements for steel lighting columns
EN 40–6 Lighting columns - Part 6: Requirements for aluminium lighting columns
EN 845–1 Specification for ancillary components for masonry - Part 1: Wall ties, tension
straps, hangers and brackets
EN 845–2 Specification for ancillary components for masonry - Part 2: Lintels
EN 1317–5 Road restraint systems - Part 5: Product requirements, test and assessment
methods and acceptance criteria
EN 1337–3 Structural bearings - Part 3: Elastomeric bearings
EN 1337–4 Structural bearings - Part 4: Roller bearings
EN 1337–5 Structural bearings - Part 5: Pot bearings
EN 1337–6 Structural bearings - Part 6: Rocker bearings
EN 1337–7 Structural bearings - Part 7: Spherical and cylindrical PTFE bearings
EN 1337–8 Structural bearings - Part 8: Guide Bearings and Restraint Bearings
EN 1856–1 Chimneys - Requirements for metal chimneys - Part 1: System chimney
products
EN 1856–2 Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and
connecting flue pipes
EN 10025–1 Hot rolled products of structural steels - Part 1: General technical delivery
conditions
EN 10088–4 Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip
of corrosion resisting steels for construction purposes
EN 10088–5 Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire,
sections and bright products of corrosion resisting steels for construction
purposes

8
 CEN/TR 17052:2017 (E)

EN 10210–1 Hot finished structural hollow sections of non-alloy and fine grain steels - Part
1: Technical delivery conditions
EN 10219–1 Cold formed welded structural hollow sections of non-alloy and fine grain steels
- Part 1: Technical delivery conditions
EN 10248–1 Hot-rolled steel sheet piling - Part 1: Technical delivery conditions
EN 10249–1 Cold-formed steel sheet piling - Part 1: Technical delivery conditions
EN 10340 Steel castings for structural uses
EN 10343 Steels for quenching and tempering for construction purposes - Technical
delivery conditions
EN 12285–2 Workshop fabricated steel tanks – Part 2: Horizontal cylindrical single skin and
double skin tanks for the aboveground storage of flammable and non-
flammable water polluting liquids
EN 12899–1 Fixed, vertical road traffic signs – Part 1: Fixed signs
EN 13084–7 Free-standing chimneys – Part 7: Product specifications of cylindrical steel
fabrications for use in single wall steel chimneys and steel liners
EN 13241–1 Industrial, commercial and garage doors and gates – Product standard – Part 1:
Products without fire resistance or smoke control characteristics
EN 13445–3 Unfired pressure vessels – Part 3: Design
EN 13479 Welding consumables – General product standard for filler metals and fluxes for
fusion welding of metallic materials
EN 13561 External blinds – Performance requirements including safety
EN 13659 Shutters – Performance requirements including safety
EN 13830 Curtain walling – Product standard
EN 14195 Metal framing components for gypsum board systems – Definitions,
requirements and test methods
EN 14351–1 Windows and doors – Product standard, performance characteristics – Part 1:
Windows and external pedestrian doorsets without resistance to fire and/or
smoke leakage characteristics
EN 14388 Road traffic noise reducing devices – Specifications
EN 14399–1 High-strength structural bolting assemblies for preloading – Part 1: General
requirements
EN 14509 Self-supporting double skin metal faced insulating panels – Factory made
products – Specifications
EN 14545 Timber structures – Connectors – Requirements
EN 14592 Timber structures – Dowel-type fasteners – Requirements
EN 14782 Self-supporting metal sheet for roofing, external cladding and internal lining –
Product specification and requirements
EN 14783 Fully supported metal sheet and strip for roofing, external cladding and internal
lining – Product specification and requirements
EN 15048–1 Non-preloaded structural bolting assemblies – Part 1: General requirements

9
CEN/TR 17052:2017 (E)

EN 15088 Aluminium and aluminium alloys – Structural products for construction works –
Technical conditions for inspection and delivery
EN 16034 Pedestrian doorsets, industrial, commercial, garage doors and openable
windows – Product standard, performance characteristics – Fire resistance
and/or smoke control characteristics

Many of the construction products listed in Table 1 form the constituent products that are used to
manufacture construction products which are assessed according to EN 1090-1. Hot rolled products of
structural steels according to EN 10025-1 or structural aluminium products according to EN 15088 are
just some examples of the constituent products that are used to make fabricated structural products
that are assessed according to EN 1090-1.
5.4.3 Construction products covered by an ETA

Structural steel and aluminium components that are covered by an ETA (European Technical
Assessment or a still valid European Technical Approval) are not covered by EN 1090-1.
A non-exhaustive list of products covered by ETAs based on ETAGs used as EADs is given in Table 2
below.
Table 2 — A list of ETAs for construction products not covered by EN 1090–1

ETA according to Component

ETAG used as EAD
ETAG 001 Metal Anchors for use in Concrete
ETAG 008 Prefabricated stairs kits
ETAG 015 Three-dimensional nailing plates
ETAG 023 Prefabricated building units
ETAG 025a Metal frame building kits
Note: include structural frame, cladding and foundations.
ETAG 029 Metal injection anchors for use in masonry
ETAG 030 Dowels for structural joints
ETAG 032 Expansion joints for road bridges
ETAG 034 - 1 Kits for external Wall Claddings – Part 1: Ventilated cladding kits
comprising cladding components and associated fixings
ETAG 034 - 2 Kits for external Wall Claddings – Part 2: Claddings kits comprising cladding
components, associated fixings, subframe and possible insulation layer
a In the case of ETAG025 two approaches are possible:
— Approach 1: if a manufacture decides not to implement ETAG025 then the requirements of
EN 1090–1 shall apply to the structural metallic elements or kits.
— Approach 2: If the manufacturer wants to consider the intended use as a building as specified in
ETAG 025 and declare additional characteristic performances resulting from it (as a minimum, the
connections to the ground and specifications for the elements of the building envelope) not taken
into account by EN 1090–1, then ETAG 025 applies.

There are too many ETAs to list in this publication. A complete list is given on the EOTA website
http://www.eota.eu.

10
 CEN/TR 17052:2017 (E)

Annex A
(informative)

Products covered by EN 1090-1

The following steel and aluminium products are covered by the scope of EN 1090-1, when the intended
use comprises a structural function. This list is indicative and non-exhaustive.
Structural components / Structural components for:

A.1 Balconies,
A.2 Balustrades if fulfilling the function of a barrier 1)
A.3 Base plates,
A.4 Beams not covered by EN 10025–1,
A.5 Beam clamps without ETA,
A.6 Bended products from hot rolled beams and steel plates,
A.7 Bracing,
A.8 Bridges (incl. road-, railway- and footbridges, pipe bridges, moving bridges),
A.9 Buildings,
A.10 Canopy framing,
A.11 Carports,
A.12 Catwalks,
A.13 Cellular Beams,
A.14 Chimneys not covered by EN 1856–1 or EN 1856–2 or EN 13084–7,
A.15 Cold-formed purlins and cladding rails,
A.16 Cold-formed sheeting for roofing and cladding if structural,
A.17 Cold-formed decking for use in composite steel and concrete floors,
A.18 Columns,
A.19 Crane supporting structures including crane runway beams, crane rails and structural end
stops,
A.20 Culverts used as a bridge-like structure to carry traffic,
A.21 Curved and bent beams,
A.22 Cut to size components from hot rolled products,
A.23 Fire escapes,
A.24 Girders not covered by EN 10025–1,
A.25 Grandstands and stadia,

1) See also European Commission's FAQ website (FAQ 31)

11
CEN/TR 17052:2017 (E)

A.26 Grillage beams and girders,

A.27 Handrails (Barriers / Edge Protection),
A.28 Hangers not covered by EN 845–1 and ETAG 015,
A.29 Lighting columns neither covered by EN 40–5 or EN 40–6 nor by an ETA,
A.30 Lintels not covered by EN 845–2,
A.31 Load bearing fences,
A.32 Marquee framing,
A.33 Machined or bended aluminium semiproducts for use as structural components,
A.34 Machinery supports, if integral part of the load bearing structure of the construction works,
A.35 Masonry structures not covered by EN 845–1, EN 845–2, or ETAG 029,
A.36 Metal frame building kits without ETA,
A.37 Mezzanine floors,
A.38 Noise barriers, not covered by EN 14388,
A.39 Opening frames for floors, walls and roofs, if integral part of the load bearing structure of
the construction works,
A.40 Pipeline supporting structures and pipe supporting structures,
A.41 Plant and machinery, if integral part of the load bearing structure of the construction works,
A.42 Plate girders (welded or bolted or riveted),
A.43 Prefabricated building units without ETA,
A.44 Prefabricated pile foundations without ETA,
A.45 Predrilled components from hot rolled beams and steel plates,
A.46 Purlins,
A.47 Racking and shelving systems, if integral part of the load bearing structure of the
construction works,
A.48 Ramps, if integral part of the load bearing structure of the construction works,
A.49 Sag rods,
A.50 Sign and gantry girders,
A.51 Silos,
A.52 Stairs without ETA,
A.53 Structural frames for buildings, warehouses, schools, hospitals, dwellings, industrial and
agricultural sheds,
A.54 Structural frames for shelters,
A.55 Structural steel components for composite steel and concrete structures,
A.56 Tanks that are not covered by EN 12285–2,
A.57 Tension rods without ETA,
A.58 Timber structures excluding fasteners,
A.59 Towers and masts,

12
 CEN/TR 17052:2017 (E)

A.60 Trusses,
A.61 Tubular beams and columns,
A.62 Walkways, incl. open mesh flooring, if integral part of the load bearing structure of the
construction works,
A.63 Wharfs, docks and piers,
A.64 Winter gardens and green houses.

13
CEN/TR 17052:2017 (E)

Annex B
(informative)

Products not covered by EN 1090-1

The following steel and aluminium products are not covered by the scope of EN 1090-1. This list is
indicative and non-exhaustive. 2)
B.1 Aluminium and aluminium alloys – Structural products for construction works according to
EN 15088,
B.2 Aluminium structural composites,
B.3 Amusement rides and devices which are machines or not permanently installed,
B.4 Balustrades unless fulfilling the function of a barrier, 3)
B.5 Beam clamps with ETA,
B.6 Bearings and steel components used in bearings according to EN 1337,
B.7 Blind rivets,
B.8 Cabinets for cables and power supply installations,
B.9 Cables, ropes and wires,
B.10 Castings,
B.11 Circulation fixtures except sign gantry and cantilevers,
B.12 Cladding kits according to ETAG 034,
B.13 Cold formed steel tubes according to EN 10219–1,
B.14 Cold storage premises according to ETAG 021
B.15 Components for suspended ceilings,
B.16 Composite light weight panels according to ETAG 016
B.17 Curtain walling according to EN 13830,
B.18 Doors according to EN 14351–1,
B.19 Dowels for structural joints according to ETAG 030,
B.20 Expansion joints for road bridges according to ETAG 032,
B.21 External blinds according to EN 13561,
B.22 Fasteners glued to timber structures,
B.23 Fastening plates and other cast into concrete fasteners not covered by design standards,
codes and regulations
B.24 Flagpoles,

2) For Wind Turbines and their Towers, see European Commission's FAQ website (FAQ 31)

3) See also European Commission's FAQ website (FAQ 31)

14
 CEN/TR 17052:2017 (E)

B.25 Forgings,
B.26 Foundation bolts, column shoes and pile joints cast into concrete not covered by design
standards, codes and regulations,
B.27 Free-standing steel chimneys according to EN 13084–7,
B.28 Fully supported metal sheet for roofing, cladding and lining according to EN 14783,
B.29 Hot finished steel tubes according to EN 10210–1,
B.30 Hot rolled steel flat products and sections according to EN 10025–1,
B.31 Industrial, commercial and garage doors and gates – without fire resistance or smoke control
according to EN 13241–1,
B.32 Joining devices for rail track isolation systems,
B.33 Lighting columns according to EN 40–5 and EN 40–6,
B.34 Lintels for masonry according to EN 845–2,
B.35 Masonry anchors according to EN 845–1,
B.36 Metal anchors for use in concrete according to ETAG 001,
B.37 Metal anchors for use in masonry according to ETAG 029,
B.38 Metal chimneys according to EN 1856–1,
B.39 Metal frame building kits with ETA,
B.40 Metal framing components for plasterboard according to EN 14195,
B.41 Metal liners according to EN 1856–2,
B.42 Non-pre-loadable bolts according to EN 15048–1,
B.43 Non-structural fences and railings,
B.44 Ornamentations,
B.45 Pedestrian door sets, industrial, commercial, garage doors and openable windows with fire
resistance and/or smoke control characteristics according EN 16034,
B.46 Piles if non-fabricated,
B.47 Pipelines and pipes,
B.48 Playground equipment,
B.49 Powder actuated fasteners,
B.50 Prefabricated building units with ETA,
B.51 Prefabricated stair kits with ETA,
B.52 Prefabricated steel and stainless steel wire rope systems with end connectors,
B.53 Prefabricated tension rod systems with fork end connectors and with ETA,
B.54 Pre-loadable bolts according to EN 14399–1,
B.55 Pressure vessels including the welded support according to EN 13445–3,
B.56 Racking and shelving systems, if not integral part of the load bearing structure of the
construction works,
B.57 Rails or sleepers for railway systems,

15
CEN/TR 17052:2017 (E)

B.58 Raised floors,

B.59 Reinforcing steel for concrete or masonry,
B.60 Road parapets, crash barriers, crash cushions according to EN 1317–5,
B.61 Road traffic noise reducing devices according to EN 14388,
B.62 Roof safety products incl. roof ladders and walkways,
B.63 Scaffoldings,
B.64 Sculptures (Metal Art),
B.65 Sandwich panels according to EN 14509,
B.66 Self-drilling and self-tapping screws,
B.67 Self-supporting metal sheets for roofing, cladding and lining according to EN 14782,
B.68 Sheet piling according to EN 10248–1 and EN 10249–1,
B.69 Shutters according to EN 13659,
B.70 Stainless steel sheet/plate and strip according to EN 10088–4,
B.71 Stainless steel bars, rods, wire, sections according to EN 10088–5,
B.72 Steel and aluminium components and elements produced on site,
B.73 Steel and aluminium stairs, walkways and fences forming integral part of a machine, silo,
tank, etc.,
B.74 Steel beams for composite steel concrete structures not covered by design standards, codes
and regulations,
B.75 Steel casting for structural use according to EN 10340,
B.76 Steels for quenching and tempering for construction purposes according to EN 10343,
B.77 Steel lintels according to EN 845–2,
B.78 Steel spring elements,
B.79 Structural components for offshore structures,
B.80 Structural double skin metal faced sandwich panels,
B.81 Tanks - Workshop fabricated steel tanks according to EN 12285–2,
B.82 Temporary structures (e.g. tents, fairground and amusement park machinery and structures)
B.83 Three-dimensional nailing plates according to ETAG 015,
B.84 Ties, tension straps, hangers and brackets for masonry according to EN 845–1,
B.85 Timber connectors according to EN 14545,
B.86 Timber dowel-type fasteners according to EN 14592,
B.87 Traditional craft type and non-structural components (e.g. weather cocks, letter boxes,
bicycle racks, fences),
B.88 Traffic sign supports according to EN 12899–1,
B.89 Tuned mass damper systems,

16
 CEN/TR 17052:2017 (E)

B.90 Viscous liquid dashpot dampers,

B.91 Welding consumables according to EN 13479,
B.92 Windows according to EN 14351–1.

17