MX175 MX200 MX250 MX300 MX360 MX400: Owner'S Manual

7VE-F8199-71 LIT-19626-02-55
OWNER’S MANUAL
MX400
MX360
MX300
MX250
MX200
la machine.
MX175 manuel avant la première utilisation de
Il convient de lire attentivement ce
Read this manual carefully before

operating this machine. MX175
MX200
MX250
MX300
MX360
MX400
MANUEL DU PROPRIÉTAIRE
LIT-19626-02-55 7VE-F8199-71
7VE-F8199-71_cover_4mm.indd 1-3 2017/10/12 16:54:34

16:54:34 2017/10/12 4-6 7VE-F8199-71_cover_4mm.indd
stay with this machine if it is sold.
Read this manual carefully before operating this machine. This manual should
Couvercle2
Cover2
Ce produit peut vous exposer à des produits chimiques, y compris les gaz
d’échappement du moteur et le monoxyde de carbone, tous deux reconnus par l’État
de Californie comme causes d’anomalies congénitales ou autres problèmes du
système reproductif.
Pour plus d’informations, visitez le site www.P65Warnings.ca.gov.
Il convient de lire attentivement ce manuel avant la première utilisation de la
machine. Le manuel doit être remis avec la machine en cas de vente de ce dernier.
7VE-F8199-71_E.book 1 ページ２０１７年１０月１０日　火曜日　午後３時２６分
Introduction
Congratulations on your purchase of your new Yamaha.
This manual will provide you with a good basic understanding of the operation and main-
tenance of this machine.
If you have any questions regarding the operation or maintenance of your machine,
please consult a Yamaha dealer.
WARNING
PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPER-
ATING THE MACHINE.
TIP
• Yamaha continually seeks advancements in product design and quality.
Therefore, while this manual contains the most current product information available at
the time of printing, there may be minor discrepancies between your machine and this
manual. If there is any question concerning this manual, please consult a Yamaha
dealer.
• This manual should be considered a permanent part of this machine and should
remain with this machine when resold.
* Product and specifications are subject to change without notice.
MX175, MX200, MX250, MX300, MX360, MX400

OWNER’S MANUAL
©2017 by Yamaha Motor Powered
Products Co., Ltd.
1st Edition, September 2017
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Powered
Products Co., Ltd.
is expressly prohibited.
Printed in China
P/N LIT-19626-02-55
Important manual information

Particularly important information is distinguished in this manual by the following nota-
tions.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
WARNING
A WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
NOTICE
A NOTICE indicates special precautions that must be taken to avoid damage to the
machine or other property.
TIP
A TIP provides key information to make procedures easier or clearer.
Contents
Safety information .................... 1 Stopping the engine .......................... 21
General safety information .................. 1 MX175/MX200............................... 21
MX250/MX300/MX360/MX400 ...... 22
Exhaust fumes are poisonous............. 1
High altitude operation ...................... 23
Fuel is highly flammable and 
poisonous............................................ 1 Periodic maintenance ............ 24
Engine and muffler may be hot ........... 2 The importance of maintenance ....... 24
Electric shock prevention .................... 3 Maintenance schedule ...................... 24
Accidental engine start prevention ...... 4 Maintenance chart ......................... 24
Rotating parts...................................... 4 Spark plug inspection........................ 26
Location of important labels ................ 5 Carburetor adjustment ...................... 27
Engine oil replacement ..................... 27
Controls and features .............. 8
Air filter/foam element ....................... 28
Description .......................................... 8
General view (MX175/MX200)......... 8 Spark arrester ................................... 30
General view (MX250/MX300/ (For MX175/MX200) ...................... 30
MX360, Manual starting models) ..... 9 (Except for MX175/MX200) ........... 32
General view (MX360/MX400,  Fuel cock........................................... 34
Electric starting models) .................. 9 Fuel tank filter ................................... 35
Control function ................................. 10 Fuse replacement (For electric 
Engine switch................................. 10 starting models) ................................ 35
Oil warning light (Red) ................... 10
Fuel tank cap ................................. 11 Storage .................................... 37
Fuel cock lever............................... 11 Drain the fuel..................................... 37
Recoil starter.................................. 11 Engine............................................... 39
Choke lever.................................... 12
Throttle lever.................................. 12 Troubleshooting ..................... 40
Engine won’t start ............................. 40
Before operation..................... 13
Manual starting models ................. 40
Preparation........................................ 13 Electric starting models (MX360/
Fuel................................................ 13 MX400) .......................................... 42
Engine oil ....................................... 14
Connecting the battery Specifications ......................... 46
(For electric starting models) ......... 15 MX175............................................... 46
Pre-operation check .......................... 16 MX200............................................... 47
Pre-operation check....................... 16 MX250............................................... 48
Operation................................. 17 MX300............................................... 49
Precautions for use ........................... 17 MX360............................................... 50
Starting the engine ............................ 17 MX400............................................... 51
MX175/MX200 ............................... 17
MX250/MX300/MX360 (Manual Consumer information ........... 52
starting).......................................... 18 Machine identification ....................... 52
MX360/MX400 (Electric starting) ... 20 For MX175/MX200 ........................ 52
Contents
Except for MX175/MX200 ..............52

Identification number records ............52
Exhaust emission control
system and components ........54
Index.........................................55
Safety information
General safety information
• Do not allow children to operate the multi-purpose
engine.
• Do not place any obstacles on the multi-purpose

engine.
• Do not sit or stand on the multi-purpose engine.
Exhaust fumes are poisonous

• Using a multi-purpose engine indoors CAN KILL
YOU IN MINUTES. Multi-purpose engine exhaust
contains carbon monoxide. This is a poison you can-
not see or smell.
• NEVER use inside a home or garage, EVEN IF
doors and windows are open.
• Only use OUTSIDE and far away from windows,
doors, and vents.
Fuel is highly flammable and poison-

ous
• Always turn off the engine when refuelling.
• Never refuel while smoking or in the vicinity of an
open flame.
1
Safety information
• Take care not to spill any fuel on the engine or muf-

fler when refueling.
• Do not leave the multi-purpose engine inside the
vehicle or in the trunk.
• If you swallow any fuel, inhale fuel vapor, or allow any
to get in your eye(s), see your doctor immediately. If
any fuel spills on your skin or clothing, immediately
wash with soap and water and change your clothes.
• When refueling, do not place the fuel tank cap near
the muffler.
• When operating or transporting the machine, be sure

it is kept upright. If it tilts, fuel may leak from the car-
buretor or fuel tank.
Engine and muffler may be hot

• Place the machine in a place where pedestrians or
children are not likely to touch the machine.
2
Safety information
• Avoid placing any flammable materials near the

exhaust outlet during operation.
• In order to prevent overheating, ensure adequate air-

flow by keeping the machine at least 1 m (3 ft) from
objects or other equipment.
• Do not operate the engine with a dust cover or other

objects covering it.
• When covering the multi-purpose engine, be sure to

do so only after the engine and muffler have com-
pletely cooled down.
Electric shock prevention

• Never operate the engine in rain or snow.
3
Safety information
• Never touch the machine with wet hands or electrical

shock will occur.
Accidental engine start prevention

• To prevent the engine from accidentally starting, be
sure to stop the engine and remove the spark plug
caps before doing any service.
Rotating parts
• Keep hands, feet, hair and clothing away from the
rotating parts.
• Never operate the multi-purpose engine without
shroud, covers or guards.
4
Safety information
Location of important labels

Please read the following labels carefully before operating this machine.
TIP
Maintain or replace safety and instruction labels, as necessary.
MX175/MX200
2
3
1 4
1 4
LISEZ LE MANUEL DU PROPRIÉTAIRE ET TOUTES LES

ÉTIQUETTES AVANT L'UTILISATION.
NE FAITES FONCTIONNER QUE DANS DES LIEUX BIEN AÉRÉS.
LES GAZ D'ÉCHAPPEMENT CONTIENNENT DU MONOXYDE DE
CARBONE NOCIF.
VÉRIFIEZ QU'IL N'Y A PAS DE FUITES DE CARBURANT OU DE
CARBURANT RENVERSÉ.
ARRÊTEZ LE MOTEUR AVANT DE FAIRE LE PLEIN.
NE PAS UTILISER PRÈS DE MATÉRIAUX INFLAMMABLES.
GARDEZ L'APPAREIL AU SEC EN TOUTES CIRCONSTANCES.
7CN-F4162-60
5
Safety information
TIP
MX250/MX300
3
1 (Except for CALIFORNIA)
1 (For CALIFORNIA)
DISPLACEMENT :
2 3
6
Safety information
TIP
MX360/MX400
2 4
1
3 4
LISEZ LE MANUEL DU PROPRIÉTAIRE ET TOUTES LES

ÉTIQUETTES AVANT L'UTILISATION.
NE FAITES FONCTIONNER QUE DANS DES LIEUX BIEN AÉRÉS.
LES GAZ D'ÉCHAPPEMENT CONTIENNENT DU MONOXYDE DE
CARBONE NOCIF.
VÉRIFIEZ QU'IL N'Y A PAS DE FUITES DE CARBURANT OU DE
CARBURANT RENVERSÉ.
ARRÊTEZ LE MOTEUR AVANT DE FAIRE LE PLEIN.
NE PAS UTILISER PRÈS DE MATÉRIAUX INFLAMMABLES.
GARDEZ L'APPAREIL AU SEC EN TOUTES CIRCONSTANCES.
7CN-F4162-60
7
Controls and features

Description
General view (MX175/MX200)
1
8 2 14
3 9
7 13
4 12
6
5 11 10
1 Fuel tank cap 8 Fuel tank

2 Air filter case cover 9 Throttle lever
3 Spark plug 10 Recoil starter handle
4 Carburetor 11 Fuel cock lever
5 Oil drain bolt 12 Engine switch
6 Oil filler cap 13 Choke lever
7 Muffler 14 Fuel tank filter
8
General view (MX250/MX300/MX360, Manual starting models)
8 1 16
7 2
15 9
6 14
13 10
3 12
5 4 11
1 Fuel tank cap 9 Oil warning light (Red)

2 Air filter case cover 10 Engine switch
3 Carburetor 11 Recoil starter handle
4 Oil drain bolt 12 Throttle lever
5 Oil filler cap 13 Fuel cock cup
6 Spark plug 14 Fuel cock lever
7 Muffler 15 Choke lever
8 Fuel tank 16 Fuel tank filter
General view (MX360/MX400, Electric starting models)
8 1 16
7 2
15 9
6 14
13 10
3 12
5 4 11
1 Fuel tank cap 9 Oil warning light (Red)

2 Air filter case cover 10 Engine switch
3 Carburetor 11 Recoil starter handle
4 Oil drain bolt 12 Throttle lever
5 Oil filler cap 13 Fuel cock cup
6 Spark plug 14 Fuel cock lever
7 Muffler 15 Choke lever
8 Fuel tank 16 Fuel tank filter
9
Control function
Engine switch
The engine switch controls the ignition system.
1. “ ” (ON)/“ ” (ON)
Ignition circuit is switched on.
The engine can be started.
2. “ ” (OFF)/“ ” (STOP)
2 1
Ignition circuit is switched off.
The engine will not run.
3. “ ” (START)
2 Starting circuit is switched on.

The starter motor starts and the engine can be started.
After starting the engine, take your hand off the switch
immediately.
1
A Manual starting models (MX175/MX200)
1 B Manual starting models (MX250/MX300/MX360)
2 3 C Electric starting models (MX360/MX400)
Oil warning light (Red)

When the oil level falls below the lower level, the oil
warning light comes on and then the engine stops
automatically. Unless you refill with oil, the engine will
not start again.
TIP
(Manual starting models)
If the engine stalls or does not start, turn the engine
switch to “ ” (ON) and then pull the recoil starter. If the
oil warning light flickers for a few seconds, the engine
oil is insufficient. Add oil and restart.
(Electric starting models)
If the engine stalls or does not start, turn the engine
switch to “ ” (START). If the oil warning light comes
on, the engine oil is insufficient. Add oil and restart.
10
Fuel tank cap

Remove the fuel tank cap by turning it counterclock-
wise.
Fuel cock lever

The fuel cock supplies fuel from the fuel tank to the car-
2 1 buretor.
The fuel cock has two positions.
1. OPEN/ON
With the lever in this position, fuel flows to the carbure-
tor. Normal using is done with the lever in this position.
2. OFF
With the lever in this position, fuel will not flow. Always
turn the lever to this position when the engine is not
running.
2 2
A MX175/MX200
B MX250/MX300/MX360/MX400
1
Recoil starter
The recoil starter is used to start the engine.
1
Pull the recoil starter slowly until it is engaged, then pull
it briskly.
1. Recoil starter handle
NOTICE
• Pull the recoil starter handle straight.
• Return the recoil starter handle slowly.
• Do not touch the recoil starter handle while the
multi-purpose engine is operating.
TIP
Pull the recoil starter handle after turning the engine
switch to “ ” (ON)/“ ” (ON).
11
Choke lever
Starting a cold engine requires a richer air-fuel mixture,
which is supplied by the choke lever.
1. Choke lever
TIP
Functions and specification differs depending on the
1 models.
A MX175/MX200
1 B MX250/MX300/MX360/MX400
701-033
Throttle lever
Throttle lever controls the engine speed.
1. “ ”
Lever position to idle the engine.
Decrease engine speed.
2. “ ”
2 1
Increase engine speed.
A MX175/MX200
B MX250/MX300/MX360/MX400
2 1
12
Before operation
Preparation
Fuel
WARNING
• Fuel is highly flammable and poisonous.
Check “Safety information” (See page 1) care-
fully before filling.
• Carefully fill the fuel tank in order to avoid fuel
from spilling out of the fuel tank.
• Stop filling when the fuel reaches the bottom of
the fuel filler, otherwise it may overflow when the
fuel warms up and expands.
• Wipe up any spilled fuel immediately.
• After filling the tank with fuel, make sure the fuel
tank cap is tightened securely.
1. Stop the engine.

2. Place the multi-purpose engine on a level surface.
3. Remove the fuel tank cap.
4. Check the fuel level.
5. If low, fill the tank with fuel. Do not fill past the bot-
tom of the fuel filler as fuel may mix with the acti-
vated charcoal in the fuel tank cap and overflow.
TIP
If filled beyond the bottom of the fuel filler, fuel may mix
with the active charcoal located within the fuel tank cap
and soil the surrounding areas.
1. Correct fuel level

1 2 3 2. Fuel tank filter
3. Bottom of fuel filler
13
Before operation
NOTICE
• Immediately wipe off spilled fuel with a clean,
dry, soft cloth, since fuel may deteriorate painted
surfaces or plastic parts.
• Use only unleaded gasoline. The use of leaded
gasoline will cause severe damage to internal
engine parts.
Recommended fuel:
Unleaded gasoline
Fuel tank capacity:
Total:
MX175 3.9 L (1.03 US gal, 0.86 Imp gal)
MX200 3.9 L (1.03 US gal, 0.86 Imp gal)
MX250 5.5 L (1.45 US gal, 1.21 Imp gal)
MX300 5.5 L (1.45 US gal, 1.21 Imp gal)
MX360 6.1 L (1.61 US gal, 1.34 Imp gal)
MX400 6.1 L (1.61 US gal, 1.34 Imp gal)
Your Yamaha engine has been designed to use regular

unleaded gasoline with a pump octane number ((R+M)/
2) of 86 or higher, or research octane number of 91 or
higher.
Engine oil
NOTICE
The multi-purpose engine has been shipped with-
out engine oil. Do not start the engine until you
have filled it with the sufficient engine oil.
1. Place the multi-purpose engine on a level surface.

2. Remove the oil filler cap.
1. Oil filler cap
14
Before operation
3. Fill the specified amount of the recommended

engine oil.
NOTICE
Be sure no foreign material enters the crankcase.
Recommended engine oil:

0 10 30 50 70 90 110130 °F Recommended oil brand:
YAMALUBE
SAE 10W-30 Available oil grade:
API SE type or higher
SAE 10W-40 JASO MA or MB
Available viscosity index:
-20 -10 0 10 20 30 40 50 °C 10W-30 or 10W-40
Engine oil quantity:
MX175/MX200 0.6 L (0.63 US qt, 0.53 Imp qt)
MX250/MX300 1.0 L (1.06 US qt, 0.88 Imp qt)
MX360/MX400 1.1 L (1.16 US qt, 0.97 Imp qt)
4. Check the oil level of the oil filler hole.

1. Correct level
5. Install the oil filler cap.
Connecting the battery

(For electric starting models)
Recommended battery capacity is 12 V/26 Ah or more.
Use battery lead wires with cross section of at least 8
mm (0.31 in) square.
1. Connect the battery positive terminal to the starter
switch.
1 2. Ground the battery negative terminal to the engine
2
mounting bolt.
15
Before operation
Pre-operation check
WARNING
If any item in the pre-operation check is not work-
ing properly, have it inspected and repaired before
operating the multi-purpose engine.
The condition of a multi-purpose engine is the owner’s

responsibility. Vital components can start to deteriorate
quickly and unexpectedly, even if the multi-purpose
engine is unused.
TIP
Pre-operation checks should be made each time the
multi-purpose engine is used.
Pre-operation check
• Fuel
- Check fuel level in fuel tank.
- Refuel if necessary.
(See page 13 for more details.)
• Fuel line
- Check fuel hose for crack or damage.
- Replace if necessary.
• Engine oil
- Check oil level in engine.
- If necessary, add recommended oil to correct level.
- Check multi-purpose engine for oil leakage.
(See page 14 for more details.)
• The point where abnormality was recognized by
use
- Check operation.
- If necessary, consult a Yamaha dealer.
16
Operation
Precautions for use
WARNING
Never operate the engine in a closed area or it may
cause unconsciousness and death within a short
time. Operate the engine in a well ventilated area.
NOTICE
The multi-purpose engine was shipped from the
factory without engine oil. Do not start the engine
for the first time until the oil level has been checked
and oil added if necessary.
Starting the engine

MX175/MX200
1. Turn the fuel cock lever to OPEN.
1 1. OPEN
2. Turn the choke lever to “START”.

1. Choke lever
TIP
The choke is not required to start a warm engine.
1 When starting the warm engine, put the choke lever to
the original position.
3. Move the throttle lever slightly in the arrow direc-

tion.
1. Throttle lever
17
Operation
4. Turn the engine switch to “ ” (ON).

1. “ ” (ON)
5. Pull the recoil starter slowly until it is engaged,

then pull it briskly.
WARNING
Be careful to use the recoil starter. In rare cases,
the recoil starter handle can be drawn back quickly
by the engine kickback.
6. After the engine starts, warm up the engine

enough so that the engine does not stop when the
choke lever is returned to the original position.
1. Original position
7. Set the throttle lever in desired position.

1. “ ”: Decrease engine speed
2. “ ”: Increase engine speed
2 1
MX250/MX300/MX360 (Manual starting)

1. Turn the fuel cock lever to ON.
1. ON
18
Operation
2. Turn the choke lever to “ ”.

1. Choke lever
TIP
1
When starting the warm engine, put the choke lever to
701-033

tion.
1. Throttle lever
1

1. “ ” (ON)
1
5. Pull the recoil starter slowly until it is engaged,
then pull it briskly.
WARNING
Be careful to use the recoil starter. In rare cases,
the recoil starter handle can be drawn back quickly
by the engine kickback.

1 enough so that the engine does not stop when the
701-033
19
Operation

2 1
MX360/MX400 (Electric starting)

1. Turn the fuel cock lever to ON.
1. ON
1
2. Turn the choke lever to “ ”.
1. Choke lever
TIP
1
When starting the warm engine, put the choke lever to
701-033

tion.
1. Throttle lever
1

1
1. “ ” (ON)
20
Operation
5. Turn the engine switch to “ ” (START).

Take your hand off the switch immediately after the
1 engine starts.
1. “ ” (START)
NOTICE
If the engine fails to start, release the switch, wait a
few seconds, then try again. Each attempt should
be as short as possible to preserve the battery. Do
not crank the engine more than 5 seconds on any
one attempt.

1 enough so that the engine does not stop when the
701-033

2 1
Stopping the engine

MX175/MX200
1. Move the throttle lever fully in the arrow direction.
1. Throttle lever
21
Operation
2. Turn the engine switch to “ ” (OFF).

1. “ ” (OFF)
3. Turn the fuel cock lever to OFF.

1 1. OFF
MX250/MX300/MX360/MX400
1. Move the throttle lever fully in the arrow direction.
1. Throttle lever
2. Turn the engine switch to “ ” (OFF)/“ ” (STOP).

1. “ ” (OFF)/“ ” (STOP)
1 A Manual starting models (MX250/MX300/MX360)

B Electric starting models (MX360/MX400)
22
Operation

1. OFF
1 1
High altitude operation

This engine may require a high altitude carburetor kit to
ensure correct engine operation at altitudes above
4000 ft. (1219 meters). If you operate your engine at
altitudes above 4000 ft. (1219 meters) consistently,
have your local Yamaha dealer perform the necessary
carburetor modification. This engine should be oper-
ated in its original configuration below 4000 ft. (1219
meters) as damage may occur if high altitude carbure-
tor kit is installed and operated below 4000 ft. (1219
meters).
23
Periodic maintenance
The importance of maintenance
Safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will
keep your multi-purpose engine in the safest and most efficient condition possible. The
most important points of multi-purpose engine inspection, adjustment, and lubrication are
explained on the following pages.
WARNING
If you are not familiar with maintenance work, have a Yamaha dealer do it for you.
Maintenance schedule
Maintenance chart
WARNING
Stop the engine before starting maintenance work.
NOTICE
Use only Yamaha specified genuine parts for replacement. Ask an authorized
Yamaha dealer for further attention.
Initial Every
Pre-opera-
Item Routine 1 month or 3 months 6 months 12 months
tion check
20 Hrs or 50 Hrs or 100 Hrs or 300 Hrs
• Check condition.
Spark plug • Clean and replace if 
necessary.
• Check fuel level and
Fuel 
leakage.
• Check fuel hose for
Fuel hose cracks or damage. 
• Replace if necessary.
• Check oil level in en-

Engine oil gine.
• Replace.  
• Clean.
Air filter/foam
• Check condition and  (*1)
element
replace if necessary.
• Check condition.
Spark arrester • Clean and replace if 
necessary.
24
Initial Every
Pre-opera-
Item Routine 1 month or 3 months 6 months 12 months
tion check
20 Hrs or 50 Hrs or 100 Hrs or 300 Hrs
• Clean and replace if
Fuel tank filter 
necessary.
• Clean and replace if
Fuel strainer 
necessary.
• Check breather hose
Crankcase
for cracks or damage. 
breather hose
• Replace if necessary.
• Decarbonize cylinder
head.
Cylinder head After every 500 Hrs. ( )
• More frequently if nec-
essary.
Valve clear- • Check and adjust when
ance engine is cold.
• Check and adjust idle
Idle speed
speed.
• Check recoil starter for
Recoil starter
damage.
• Check all fittings and
Fittings/fas-
fasteners.
teners
• Correct if necessary.
The point where abnormality was recog-

nized by use.
*1····· The air filter and foam element need to be cleaned more frequently when using in
unusually wet or dusty areas.
····· Since these items require special tools, data and technical skills, have a Yamaha
dealer perform the service.
25
Spark plug inspection

The spark plug is important engine components, which
should be checked periodically.
1. Remove the spark plug cap and the spark plug.
1. Spark plug cap
1 2. Spark plug
A MX175/MX200
B MX250/MX300/MX360/MX400
2
1
2
2. Check for discoloration and remove the carbon.

The porcelain insulator around the center elec-
trode of spark plug should be a slightly colored
light gray.
3. Check the spark plug type and gap.
1. Spark plug gap
Standard spark plug:

BPR4ES (NGK)
1 Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
TIP
The spark plug gap should be measured with a wire
thickness gauge and, if necessary, adjusted to specifi-
cation.
4. Install the spark plug and then tighten it.
Spark plug tightening torque:

20 N·m (2.0 kgf·m, 15 lb·ft)
TIP
If a torque wrench is not available when installing a
spark plug, a good estimate of the correct torque is
1/4–1/2 turn past finger tight. However, the spark
26
plug should be tightened to the specified torque as

soon as possible.
5. Install the spark plug cap.
Carburetor adjustment
The carburetor is a vital part of the engine. Adjusting
should be left to a Yamaha dealer with the professional
knowledge, specialized data, and equipment to do so
properly.
Engine oil replacement

WARNING
Avoid draining the engine oil immediately after
stopping the engine. The oil is hot and should be
handled with care to avoid burns.
1. Place the multi-purpose engine on a level surface

and warm up the engine for several minutes. Then
stop the engine and turn the fuel cock lever to OFF.
2. Remove the oil filler cap.
3. Place an oil pan under the engine. Remove the oil
drain bolt and gasket so that the oil can be com-
pletely drained.
4. Check the oil drain bolt, oil filler cap and O-ring.
4 3 Replace them if damaged.
1. Oil drain bolt
1 2 2. Gasket
3. O-ring
4. Oil filler cap
5. Install a new gasket and the oil drain bolt, and then
tighten the bolt.
Oil drain bolt tightening torque:

27 N·m (2.7 kgf·m, 20 lb·ft)
27
6. Add engine oil to the correct level.

1. Correct level
1 NOTICE
Be sure no foreign material enters the crankcase.
Recommended engine oil:

0 10 30 50 70 90 110130 °F
Recommended oil brand:
YAMALUBE
SAE 10W-30
Available oil grade:
API SE type or higher
SAE 10W-40
JASO MA or MB
Available viscosity index:
-20 -10 0 10 20 30 40 50 °C
10W-30 or 10W-40
Engine oil quantity:
MX175/MX200 0.6 L (0.63 US qt, 0.53 Imp qt)
MX250/MX300 1.0 L (1.06 US qt, 0.88 Imp qt)
MX360/MX400 1.1 L (1.16 US qt, 0.97 Imp qt)
7. Install the oil filler cap.
Air filter/foam element

1. Remove the air filter case cover nut and then
remove the air filter case cover.
1 1. Air filter case cover nut
2. Air filter case cover
2 A MX175/MX200
B MX250/MX300/MX360/MX400
28
2. Remove the wing nut and then remove the air filter
1 assembly.
1. Wing nut
2
2. Air filter assembly
A MX175/MX200
B MX250/MX300/MX360/MX400
1
2
3. Remove the foam element.

1. Foam element
2. Air filter
2 1
4. Wash the foam element in white kerosene and dry

it.
WARNING
Never use white kerosene while smoking or in the
vicinity of an open flame.
5. Check the foam element and replace it if neces-

sary.
6. Oil the foam element and squeeze out excess oil.
The foam element should be wet but not dripping.
Recommended oil:
Foam-air-filter oil or engine oil (See page 27)
NOTICE
Do not wring out the foam element when squeezing
it. This could cause it to tear.
7. Clean the air filter by blowing it from the inside with

compressed air.
8. Check the air filter and replace it if necessary.
29
9. Install the foam element onto the air filter.
NOTICE
The engine should never run without the air filter
assembly; excessive piston and cylinder wear may
result.
TIP
Be sure the foam element sealing surface matches the
air filter so there is no air leak.
10. Install the air filter assembly and then tighten the
wing nut.
11. Install the air filter case cover and then tighten the
air filter case cover nut.
Spark arrester
(For MX175/MX200)
WARNING
The engine and muffler will be very hot after the
engine has been run.
Avoid touching the engine and muffler while they
are still hot with any part of your body or clothing
during inspection or repair.
1. Remove the muffler cover bolts and then remove

1 the muffler cover.
1. Muffler cover bolt
2 2. Muffler cover
2. Loosen the muffler cap bolt and then remove the

muffler cap and muffler screen.
2
1. Muffler cap bolt
2. Muffler cap
3 3. Muffler screen
1
30
3. Use a flathead screw driver to pry out and remove

1 the spark arrester from the muffler.
1. Spark arrester
4. Remove the carbon deposits on the muffler cap,

muffler screen and spark arrester using a wire
brush.
NOTICE
When cleaning, use the wire brush lightly to avoid
damaging or scratching of the muffler screen and
spark arrester.
5. Check the muffler screen and spark arrester.

Replace them if damaged.
2 1
6. Install the spark arrester.
TIP
Align the spark arrester lump with the hole in the muf-
fler pipe.
1. Spark arrester lump

2. Hole
2
7. Install the muffler screen to the muffler cap, then
1 install the muffler cap to the muffler.
1. Muffler cap
2. Muffler screen
31
TIP
1 Install the muffler cap until it contacts with the projec-
tion on the muffler.
1. Projection
8. Install the muffler band, then tighten the muffler

cap bolt.
1 1. Muffler band
Muffler cap bolt tightening torque:

3.5 N·m (0.35 kgf·m, 2.6 lb·ft)
9. Install the muffler cover to the muffler, then install

the muffler cover bolts.
Muffler cover bolt tightening torque:

10 N·m (1.0 kgf·m, 7.4 lb·ft)
(Except for MX175/MX200)
WARNING
The engine and muffler will be very hot after the
engine has been run.
Avoid touching the engine and muffler while they
are still hot with any part of your body or clothing
during inspection or repair.
1. Remove the screw.

1. Screw
32
2. Use a flathead screw driver to pry out and remove

1 the spark arrester from the muffler.
1. Spark arrester
3. Remove the carbon deposits on the spark arrester

using a wire brush.
NOTICE
When cleaning, use the wire brush lightly to avoid
damaging or scratching of the spark arrester.
4. Check the spark arrester.

Replace it if damaged.
5. Install the spark arrester.
1. Spark arrester lump
2. Hole
2 TIP
Align the spark arrester lump with the hole in the muf-
1 fler pipe.
6. Install the screw, and then tighten it.
33
Fuel cock
WARNING
Never use the gasoline while smoking or in the
1. Stop the engine.

3. Remove the fuel cock cup, gasket and fuel strainer.
4. Clean the cup and fuel strainer with gasoline and
wipe it off.
5. Check the gasket. Replace it if damaged.
6. Install the fuel strainer, gasket and fuel cock cup.
WARNING
Be sure the fuel cock cup is tightened securely.
1. Fuel cock cup

3
2. Gasket
2
3. Fuel strainer
34
Fuel tank filter

WARNING
1 Never use the gasoline while smoking or in the
2
1. Remove the fuel tank cap and fuel tank filter.
1. Fuel tank cap
2. Fuel tank filter
2. Clean the fuel tank filter with gasoline.
Replace it if damaged.
3. Wipe the fuel tank filter and insert it.
4. Install the fuel tank cap.
WARNING
Be sure the fuel tank cap is tightened securely.
Fuse replacement (For electric start-

ing models)
WARNING
Be sure to use specified fuse. A wrong fuse will
cause electrical system damage and A FIRE HAZ-
ARD.
NOTICE
Be sure the engine switch is turned to “ ” (STOP)
to prevent accidental short circuiting.
35
2
1. Remove the screws and bolts, and then remove
the cover.
1. Screw/Bolt
2. Cover
1 1
2. Replace the blown fuse with one of proper amper-

age.
1. Fuse
Specified fuse:
1 10 A
TIP
If the fuse immediately blows again, consult a Yamaha
dealer.
3. Install the cover, and then tighten the screws and

bolts.
36
Storage
Long term storage of your machine will require some
preventive procedures to guard against deterioration.
Drain the fuel

1. “ ” (OFF)/“ ” (STOP)
B Manual starting models (MX250/MX300/MX360)
C Electric starting models (MX360/MX400)
1
2. Remove the fuel tank cap and fuel tank filter.

Extract the fuel from the fuel tank into an approved
gasoline container using a commercially available
hand siphon. Then, install the fuel tank filter and
the fuel tank cap.
WARNING
Fuel is highly flammable and poisonous. Check
“Safety information” (See page 1) carefully.
NOTICE
Immediately wipe off spilled fuel with a clean, dry,
soft cloth, since fuel may deteriorate painted sur-
faces or plastic parts.
37
Storage
3. Turn the engine switch to “ ” (ON)/“ ” (ON).

1. “ ” (ON)/“ ” (ON)
B Manual starting models (MX250/MX300/MX360)
C Electric starting models (MX360/MX400)
1
4. Turn the fuel cock lever to OPEN/ON.

1 1. OPEN/ON
A MX175/MX200
B MX250/MX300/MX360/MX400
1
5. Start the engine and leave it run until it stops.
The engine stops in approximately 20 minutes time
by running out of fuel.
TIP
Duration of the running engine depends on the amount
of the fuel left in the tank.
38
Storage
6. Drain the fuel from the carburetor into a clean con-

tainer by loosening the drain screw on the carbure-
tor float chamber. Pour the drained fuel into the
same approved gasoline container as the fuel from
the fuel tank.
1. Drain screw
1 7. Tighten the drain screw.
10. Tighten further if any screws, bolts and nuts are
loose.
11. Store the multi-purpose engine in a dry, well-venti-
lated place, with the cover placed over it.
Engine
Perform the following steps to protect the cylinder, pis-
ton ring, etc. from corrosion.
1. Remove the spark plug, pour about one table-
spoon of engine oil (See page 27) into the spark
plug hole and reinstall the spark plug only. Recoil
start the engine by turning over several times (with
ignition off) to coat the cylinder walls with oil.
2. Pull the recoil starter until you feel compression.
Then stop pulling. (This prevents the cylinder and
valves from rusting.)
3. Clean exterior of the multi-purpose engine and
apply a rust inhibitor.
4. Store the multi-purpose engine in a dry, well-venti-
lated place, with the cover placed over it.
5. The multi-purpose engine must remain in a vertical
position when stored, carried or operated.
39
Troubleshooting
Engine won’t start
Manual starting models
1. Check the recoil starter.
a. Turn the engine switch to “ ” (ON).
1. “ ” (ON)
A MX175/MX200
B MX250/MX300/MX360
b. Pull the recoil starter.
c. Consult a Yamaha dealer, if the machine does

not crank.
2. Check the engine oil system.
b. Pull the recoil starter.
c. Check if the oil warning light flickers.
40
Troubleshooting
d. Check the engine oil level.
e. Add engine oil, if the engine oil level is low.
f. Consult a Yamaha dealer, if the engine oil level

is correct.
3. Check the spark plug.
WARNING
• To prevent FIRE HAZARDS be sure fuel is not
present in the spark plug area.
• To prevent FIRE HAZARDS be sure to place the
spark plug as far away as possible from the
spark plug hole and carburetor area.
• To prevent ELECTRIC SHOCK do not hold spark
plug lead with hand while testing.

b. Check the spark plug for spark strength.
c. Clean the spark plug if it has excessive carbon

deposits.
41
Troubleshooting
d. Check the spark plug gap, and adjust it if it is

incorrect.
Spark plug gap:

0.7–0.8 mm (0.028–0.031 in)
e. Replace the spark plug if it still does not spark.

BPR4ES (NGK)
20 N·m (2.0 kgf·m, 15 lb·ft)
4. Check the fuel system.

a. Check the fuel level and add fuel if the fuel
level is low.
b. Check if the fuel cock lever is OPEN/ON.

1 1. OPEN/ON
A MX175/MX200
B MX250/MX300/MX360/MX400
1
c. Check the fuel line, carburetor and air filter
clogging. 
Clean or replace if they are clogged.
d. Check the foreign matter in fuel cock. Clean
the fuel cock.
Electric starting models (MX360/MX400)
1. Check the starter motor.
42
Troubleshooting

1
1. “ ” (ON)
b. Turn the engine switch to “ ” (START).

1. “ ” (START)
1
c. Consult a Yamaha dealer, if the machine does

not crank.
2. Check the engine oil system.
a. Turn the engine switch to “ ” (START).
b. Check if the oil warning light comes on.
c. Check the engine oil level.
d. Add engine oil, if the engine oil level is low.
e. Consult a Yamaha dealer, if the engine oil level

is correct.
43
Troubleshooting
3. Check the spark plug.
WARNING
• To prevent FIRE HAZARDS be sure fuel is not
present in the spark plug area.
• To prevent FIRE HAZARDS be sure to place the
spark plug as far away as possible from the
spark plug hole and carburetor area.
• To prevent ELECTRIC SHOCK do not hold spark
plug lead with hand while testing.
a. Turn the engine switch to “ ” (START).

b. Check the spark plug for spark strength.
c. Clean the spark plug if it has excessive carbon

deposits.
d. Check the spark plug gap, and adjust it if it is

incorrect.
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
e. Replace the spark plug if it still does not spark.

BPR4ES (NGK)
20 N·m (2.0 kgf·m, 15 lb·ft)
4. Check the fuel system.
44
Troubleshooting
a. Check the fuel level and add fuel if the fuel

level is low.
b. Check if the fuel cock lever is ON.
c. Check the fuel line, carburetor and air filter

clogging.
Clean or replace if they are clogged.
d. Check the foreign matter in fuel cock. Clean
the fuel cock.
45
Specifications
MX175
DIMENSIONS:
Overall length mm (in) 313–338 (12.32–13.31)
Overall width mm (in) 352 (13.86)
Overall height mm (in) 386–407 (15.19–16.02)
Dry weight kg (lb) 18 (39.68)
ENGINE:
Type Air cooled 4-stroke gasoline OHV
Cylinder arrangement 1 cylinder
Displacement cm³ 171
Bore  Stroke mm (in) 66.0  50.0 (2.59  1.97)
Starting method Recoil starter
Fuel Unleaded gasoline*
Fuel tank capacity L (US gal, Imp gal) 3.9 (1.03, 0.86)
Engine oil quantity L (US qt, Imp qt) 0.6 (0.63, 0.53)
Ignition system TCI
Spark plug type BPR4ES (NGK)
Spark plug gap mm (in) 0.7–0.8 (0.028–0.031)
*Your Yamaha engine has been designed to use regular unleaded gasoline with a pump
octane number ((R+M)/2) of 86 or higher, or research octane number of 91 or higher.
NOTICE
Use only unleaded gasoline. The use of leaded gasoline will cause severe damage
to internal engine parts.
46
Specifications
MX200
DIMENSIONS:
Overall length mm (in) 313–321 (12.32–12.64)
Dry weight kg (lb) 18 (39.68)
ENGINE:
Bore  Stroke mm (in) 70.0  50.0 (2.76  1.97)
Ignition system TCI
NOTICE
47
Specifications
MX250
DIMENSIONS:
Overall length mm (in) 390 (15.35)
Overall height mm (in) 480 (18.9)
Dry weight kg (lb) 20–27 (44–60)
ENGINE:
Bore  Stroke mm (in) 80.0  59.0 (3.15  2.32)
Ignition system TCI
NOTICE
48
Specifications
MX300
DIMENSIONS:
Overall height mm (in) 480 (18.9)
Dry weight kg (lb) 20–27 (44–60)
ENGINE:
Bore  Stroke mm (in) 80.0  59.0 (3.15  2.32)
Ignition system TCI
NOTICE
49
Specifications
MX360
DIMENSIONS:
Overall width mm (in) 462–480 (18.19–18.9)
Dry weight kg (lb) 33–39 (72.75–85.98)
ENGINE:
Bore  Stroke mm (in) 85.0  63.2 (3.35  2.49)
Starting method Recoil starter/Electric starter
Ignition system TCI
NOTICE
50
Specifications
MX400
DIMENSIONS:
Overall length mm (in) 392.5–418 (15.45–16.46)
Overall width mm (in) 462–480 (18.19–18.9)
Dry weight kg (lb) 33–39 (72.75–85.98)
ENGINE:
Bore  Stroke mm (in) 85.0  71.0 (3.35  2.80)
Starting method Recoil starter/Electric starter
Ignition system TCI
NOTICE
51
Consumer information
Machine identification
For MX175/MX200
The machine serial number is stamped in the location
as shown.
1. Machine serial number
1
TIP
The first four digits of these numbers are for model
identification (PRI-I.D. CODE); the remaining digits are
the unit production number (SERIAL No). Keep a
record of these numbers for reference when ordering
parts from a Yamaha dealer.
Except for MX175/MX200

The machine serial number is stamped in the location
as shown.
1. Machine serial number
TIP
1 The first four digits of these numbers are for model
identification (PRI-I.D. CODE); the remaining digits are
the unit production number (SERIAL No). Keep a
record of these numbers for reference when ordering
parts from a Yamaha dealer.
Identification number records

Record your model type, Primary I.D., and serial num-
bers in the spaces provided, to assist you in ordering
spare parts from a Yamaha dealer.
Also record and keep these I.D. numbers in a separate
place in case your machine is stolen.
MODEL:
PRI-I.D. CODE:
52
Consumer information
SERIAL No:
53
Exhaust emission control system and

components
****
Item Acronym
9 CARB. ASSY., LH. & JT., ...................... CARB (Carburetor)
CARBURETOR2
9 T.C.I. MAGNETO ASSY. & .................... EI (Electronic Ignition)
PLUG, SPARK
9 CRANKCASE1 & HEAD, ....................... PCV (Positive Crankcase
CYLINDER1 Ventilation)
9 AIR FILTER ASSY. ................................ ACL (Air Cleaner)
9 MUFF., 2, CAP, NET, WIRE2 &
ARRESTER, SPARK
The above items and the corresponding acronyms are provided in accordance with U.S.
EPA REGULATIONS FOR NEW NONROAD SPARK-IGNITION NONHANDHELD
ENGINES.
The acronyms conform to the latest version of the SAE’s recommended practice docu-
ment J1930, “Diagnostic Acronyms, Terms, and Definitions For Electrical/Electronic
System”.
It is recommended that these items be serviced by a Yamaha dealer.
54
Index
A Machine identification 
Accidental engine start prevention ................4 (For MX175/MX200) ...................................52
Air filter/foam element .................................28 Maintenance chart ......................................24
C Maintenance schedule................................24
Carburetor adjustment ................................27 Manual starting models...............................40
Choke lever .................................................12 O
Connecting the battery (For electric  Oil warning light (Red) ................................10
starting models)...........................................15 P
Control function ...........................................10 Precautions for use.....................................17
D Pre-operation check....................................16
Description ....................................................8 Preparation .................................................13
Drain the fuel...............................................37 R
E Recoil starter...............................................11
Electric shock prevention ..............................3 Rotating parts ...............................................4
Electric starting models (MX360/MX400)....42 S
Engine .........................................................39 Spark arrester 
Engine and muffler may be hot .....................2 (Except for MX175/MX200) ........................32
Engine oil ....................................................14 Spark arrester (For MX175/MX200) ...........30
Engine oil replacement................................27 Spark plug inspection .................................26
Engine switch ..............................................10 Specifications, MX175 ................................46
Engine won’t start........................................40 Specifications, MX200 ................................47
Exhaust fumes are poisonous.......................1 Specifications, MX250 ................................48
F Specifications, MX300 ................................49
Fuel .............................................................13 Specifications, MX360 ................................50
Fuel cock.....................................................34 Specifications, MX400 ................................51
Fuel cock lever ............................................11 Starting the engine, MX175/MX200............17
Fuel is highly flammable and poisonous .......1 Starting the engine, MX250/MX300/MX360
Fuel tank cap...............................................11 (Manual starting) .........................................18
Fuel tank filter..............................................35 Starting the engine, MX360/MX400 
Fuse replacement (For electric starting (Electric starting) .........................................20
models) .......................................................35 Stopping the engine, MX175/MX200 ..........21
G Stopping the engine, MX250/MX300/
General safety information ............................1 MX360/MX400 ............................................22
General view (MX175/MX200) ......................8 T
General view (MX250/MX300/MX360,  The importance of maintenance .................24
Manual starting models)................................9 Throttle lever ...............................................12
General view (MX360/MX400, Electric 
starting models).............................................9
H
High altitude operation ................................23
I
Identification number records......................52
L
Location of important labels ..........................5
M
Machine identification 
(Except for MX175/MX200).........................52
55
Printed in China
2017.10  1 !
(E)

MX175 MX200 MX250 MX300 MX360 MX400: Owner'S Manual

Uploaded by

Copyright:

Available Formats

MX175 MX200 MX250 MX300 MX360 MX400: Owner'S Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MX175 MX200 MX250 MX300 MX360 MX400: Owner'S Manual

Uploaded by

Copyright:

Available Formats

7VE-F8199-71 LIT-19626-02-55

Read this manual carefully before

7VE-F8199-71_cover_4mm.indd 1-3 2017/10/12 16:54:34

* Product and specifications are subject to change without notice.

MX175, MX200, MX250, MX300, MX360, MX400

Important manual information

Except for MX175/MX200 ..............52

• Do not place any obstacles on the multi-purpose

Exhaust fumes are poisonous

Fuel is highly flammable and poison-

• Take care not to spill any fuel on the engine or muf-

• When operating or transporting the machine, be sure

Engine and muffler may be hot

• Avoid placing any flammable materials near the

• In order to prevent overheating, ensure adequate air-

• Do not operate the engine with a dust cover or other

• When covering the multi-purpose engine, be sure to

Electric shock prevention

• Never touch the machine with wet hands or electrical

Accidental engine start prevention

Location of important labels

LISEZ LE MANUEL DU PROPRIÉTAIRE ET TOUTES LES

LISEZ LE MANUEL DU PROPRIÉTAIRE ET TOUTES LES

Controls and features

1 Fuel tank cap 8 Fuel tank

Controls and features

General view (MX250/MX300/MX360, Manual starting models)

1 Fuel tank cap 9 Oil warning light (Red)

General view (MX360/MX400, Electric starting models)

1 Fuel tank cap 9 Oil warning light (Red)

Controls and features

2 Starting circuit is switched on.

Oil warning light (Red)

Controls and features

Fuel tank cap

Fuel cock lever

Controls and features

1. Stop the engine.

1. Correct fuel level

Your Yamaha engine has been designed to use regular

1. Place the multi-purpose engine on a level surface.

3. Fill the specified amount of the recommended

Recommended engine oil:

4. Check the oil level of the oil filler hole.

5. Install the oil filler cap.

Connecting the battery

The condition of a multi-purpose engine is the owner’s

Starting the engine

2. Turn the choke lever to “START”.

3. Move the throttle lever slightly in the arrow direc-

4. Turn the engine switch to “ ” (ON).

5. Pull the recoil starter slowly until it is engaged,

6. After the engine starts, warm up the engine

7. Set the throttle lever in desired position.

MX250/MX300/MX360 (Manual starting)

2. Turn the choke lever to “ ”.

3. Move the throttle lever slightly in the arrow direc-

4. Turn the engine switch to “ ” (ON).

6. After the engine starts, warm up the engine