MQB Atualizado
MQB Atualizado
MQB Atualizado
MQB Encodings
It is recommended to create a complete auto-scan and adaptation channel images ("AdpMap") of all ECUs to be customized before the changes are made.
Start VCDS > applications > ECU image > address "XX", access authorization "YYYYY", function "Customization", format "CSV file" > Start
The access permissions can be found in the next chapter.
In newer VCDS versions, images of all ECUs in the vehicle can be created instead of just one address. This is recommended for the first contact with a vehicle!
This overview is created exclusively in my spare time. As a private project, I do not receive any remuneration for this. I hope to save time not only for myself,
but also for others by not having to search through thousands of websites. Since time is also money, I am of course also happy about financial support of any
kind.
Zugriffsberechtigungen
Automatic controller Login Function
01 (motor electronics) 27971 Activation of the customization
79153 ???
12233 Injector adaptation/calibration
03 (Bremsenelektronik) -------- (Logins without a known function are not listed for this STG due to the quantity)
11966 Activation of the adjustment of the hydraulic brake assistant (IDE05055)
20103 Activation of the adaptation of the erw. electronic differential lock XDS (IDE05286)
24990 Activation of the customization
25757 Activation of brake stabilization adjustment (IDE05161)
25004 Brake booster adaption
31857 Activation of the basic setting and adjustment
"ECE R119" > cornering light is already activated when stationary (factory setting)"ECE R48" > cornering light only activates from 1 km/h, i.e. only when
rolling
> channel "Driving light and parking light all-weather light switch-on limit" adjust > speed in km/h
> channel "Driving light and parking light all-weather light switch-off limit" adjust > speed in km/h
STG 13 > access authorization: 14117 > adjustment > channel "Avoidance for inadmissible overtaking" change > value to "on" or "off"
STG 13 > enable or disable encoding > byte 02 > bit 5 ("Overtaking Right Prevention active")
> channel "Acoustic measure: tensioning logic" adjust > value to "Increased traction" > channel "Acoustic measure: Gasoline
Anti_hum_measure_benzin_gear_4" adjust > value to "no measure"
> channel "Acoustic measure: Gasoline Anti_hum_measure_benzin_gear_5" adjust > value to "no measure"
> channel "Acoustic measure: Gasoline Anti_hum_measure_benzin_gear_6" > value to "no measure" Adjust the
value to "no measure" > channel "Acoustic measure: petrol Anti_hum_measure_benzin_gear_7_plus" adjust > value to "no measure"
> channel "Acoustic measure: petrol Anti_impact_driver_measure_benzin_gear_4" adjust > value to "no measure"> channel
"Acoustic measure: petrol Anti_impact_driver_measure_benzin_gear_5" adjust > value to "no measure"
> channel "Interior light 2nd generation soft color change" adjust > value to "active" (if desired)
> channel "Interior light 2nd generation center console lighting multicolored" adjust > value to "active" (if installed)
> channel "Interior light 2nd generation instrument panel lighting multicolored" adjust > value to "active" (if AID installed)
> Channel "Indoor Light 2nd Generation Speaker Lighting Multicolored" adjust > value to "active" (if installed)
> channel "Indoor Light Luminaire Configuration Ambiente_Applikationsleisten_in_Instrumententafel" adjust > value to "installed> channel "Indoor Light
Luminaire Configuration Center Console Lighting" adjust > value to "installed" (if installed)
> Adjust "Indoor Light Luminaire Configuration Frei_Farbwahl_ueber_HMI" channel > value to "notactive"
> Channel "Indoor Light Luminaire Configuration-Ambient_Farbliste_HMI" adjust > value to "active> channel "Indoor light luminaire configuration-Ambience
menu with all zones" adjust > value to "active> channel "Indoor light luminaire configuration ambience menu with global off" > value to "active"
After the coding is complete, the infotainment must be restarted via the reset (hold the power button for 10 seconds).
Note: The colors are usually reproduced 1:1 in infotainment and AID. Slight adjustments may be necessary for the LIN colors, as the colors may differ due to the
different luminous intensity of the LEDs.
© 2013-2021 Daniel Fuchs Side 23
STG 09 > access authorization: 31347 > adaptation > ...
> channels "Ambient Light Color List Red Value Color?" > adjust values in the range of 0-255> channels "Ambient Light Color List GreenValueColor?" adjust
> values in the range of 0-255> Channels "AmbientLight Color List Blue Value Color?" adjust > values in the range of 0-255
> channels "IndoorLight 2nd Generation Red Value Color?" adjust > values in the range of 0-255
> channels " Indoor Light 2.Generation Green Value Color ?" > adjust values in the range of 0-255
> channels "IndoorLight 2.Generation Blue Value Color?" adjust > values in the range of 0-255
> Ambient Light Color List Red Value channels adjust > values in the range of 0-255> Ambient Light Color List Green Value channels adjust > values in the
range of 0-255> Ambient Light Color List Blue Value channels Adjust > values in the range of 0-255> Ambient Light Color List LIN Rotwert_Farbe_?_lin
channels adjust > values in the range of 0-255> Lines "Ambient Light Color List LIN Gruenwert_Farbe_?_lin" channels adjust > values in the range of 0-255>
channels "Ambient light color list LIN Blauwert_Farbe_?_lin" > adjust values in the range of 0-255
> channels "Ambience_lightning_color_list_2 red value color ?" > adjust values in the range of 0-255> channels"Ambience_lightning_color_list_2-green
value color ?" > adjust values in the range of 0-255> channels "Ambience_lightning_color_list_2 blue value color ?" > adjust values in the range of 0-255>
channels "Ambience_lightning_color_list_lin_2-Rotwert_Farbe_?_lin > value in the range of 0-255> channels "Ambience_lightning_color_list_lin_2-
Gruenwert_ Farbe_?adjust _lin > value in the range of 0-255> channels "Ambience_lightning_color_list_lin_2-Blauwert_Farbe_?adjust _lin > value in the
range of 0-255
> channel "Interior light 2nd generation Ambiente_Farbwahl_FPA_waehlbare_Kopplung" adjust > value to "active> channel "Interior light 2nd generation
Ambiente_Farbwahl_FPA_waehlbare_Kopplung_Status_hmi_default" adjust > value to "coupled> channel"Ambient light Assignment of color to the driving
profile Fahrprofil_?" adjust > value as desired
© 2013-2021 Daniel Fuchs Side 24
The mapping can vary depending on the gateway. Here you may have to rehearse. The color values are retrieved from the channel list "Ambient Light Color List"
and "Ambient Light Color List LIN". The function must then be activated in the CAR menu under ambient lighting.
> "Indoor Lighting Parameter p_helligkeit_Tueren_geschlossen_HD_zu_zuendung_aus_tueren" channel, adjust > value to "100%> "Indoor Lighting
Parameter p_helligkeit_Fzg_geschlossen_zuendung_ein_tueren" channel adjust > value to "100%"
> channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function A 17" adjust > value to "not active" (factory setting: ambient light 3)
> channel "Luminaire16BLK SLB35BLK SL KC9 light function B 16" adjust > value to "Ambient light 3" (factory setting: not active)
STG 01 > enable encoding > bytes 05 > bit 4 ("Trailer installed")
STG 03 > access authorization: 24990 > adjustment > channel "Team stabilization" set > value to "activated"
STG 09 >
set > byte 01 > bit 0-7 to "01 Trailer Connector Diagnosis active"
> set byte 03 > bit 0-7 to the appropriate entry (see retrofit instructions)
(for vehicles without coding » SW parts index >= BA) > access authorization: 31347 > adjustment > channel "Networking connection > set value to
"installed"
STG 10 > Zugriffsberechtigung: 71679 > Codierung > Byte 03 > Bit 0-1 auf "01 Trailer Hitch installed (manually removable)" setzen
STG 13 > …
or
STG 34 > enable encoding > bytes 00 > bit 7 ("trailer, 0 = not installed / 1 = installed")
(for SW part number 5Q0) > byte 02 > bit 4-7 to "20 ECU for draw bar,with ECU for draw bar"
or
(for SW part number 2Q0 and 3Q0) > bytes 00 > bit 4-7 to "10 ECU for draw bar,with ECU for draw bar"
Enable STG 6D > encoding > byte 01 > bit 7 ("trailer, 0=not installed / 1=installed")
(for SW part number 5Q0) set > bytes 16 > bits 0-7 to "01 trailer_control_module,built-in"
or
(for SW part number 3Q0) Enable > bytes 11 > bit 0 ("AAG,0=not_coded / 1=coded")
or
(for SW part number 2Q0) enable > byte 05 > bit 4 ("AAG,0=not_coded / 1=coded")
> set byte 01 > bit 0-3 to "01 diagnostics of the line to the socket,active>byte 03 > bit 0-3 to "01 terminal 30 output (pin 9 socket),activated"
Especially when manoeuvring, the factory setting "Normal" can be pushed,because you have to accelerate a little more until the brakecomes off. Especially in
narrow parking spaces, this can also be critical, because the car makes a set forward. The setting "Early" is ideal ifyou want to use Auto Hold!
"Last setting"> factory setting, active/inactive is controlled via buttons in the center console"Never active" > Auto-Hold always deactivated
after ignition change"
Always active" > Auto-Hold always activated after ignition change
Enable > bytes 25 > bit 0 > bytes 25 > bit 1 (not for all-wheel drive)
"Early" > brake releases quickly and with little throttle (hardly noticeable or not noticeable, no jerk)
"Normal" > factory setting (jerk noticeable)
"Late" > brake releases late and only with a relatively high amount of throttle (strong jerk)
> channel "Luminaire18BLK HLA60 light function C 18" set > value to "rear lid open> channel "Luminaire18BLK HLA60 dimming value CD 18" set >
percentage value as desired (factory setting: 0)> channel"Luminaire19BLK HRC31 light function C 19" set > value to "tail lid open> channel "Luminaire19BLK
HRC31 dimming value CD 19" set > percentage value as desired (factory setting: 0)
> channel "Luminaire4TFL LB4 light function E 4" > value to "Indoor light> channel "Luminaire4TFL LB4 dimming value EF 4" set > value to "100> channel
"Luminaire5 TFL RB32 light function E 5" set > value to "Indoor light> channel "Luminaire5 TFL RB32 dimming value EF 5" set > value to "100> channel
"Luminaire2SL VLB10 light function E 2" set > value to "Indoor light> channel "Luminaire2SL VLB10 dimming value EF 2" > value to "26"> channel
"Luminaire3SL VRB21 light function E 3" > Value to "Indoor Light> Channel "Luminaire3SL VRB21 Dimming Value EF 3" set > Value to "26"
> Channel "Luminaire20BR LA71 Light Function F 20" set > Value to "Indoor Light"> Channel
"Leuchte21BR RC8 Light Function F 21" set > Value to "Indoor Light"> Channel
"Luminaire23SL HLC10 Light Function D 23" > Value to"Indoor Light"> Channel
"Luminaire24SL HRA65 Light Function D 24 " set > value to "indoor light"
> channel "Comfort lighting menu setting Cominghome" > value in seconds (value range: 0-90)> channel "Comfort lighting menu setting Leaving-Home Time
via BAP" adjust > value in seconds (value range: 0-90)
Coming Home/Leaving Home without low beam (daytime running lights or parking lights only)
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Comfort Lighting-Coming Home Lights" set > value to "Low beam> channel "Luminaire6ABL LC5 light function C 6" set > value to"not active"
(factory setting: Coming Home or Leaving Home active)> channel"Luminaire7ABL RB1 light function C 7" set > value to"not active" (factory setting: Coming
Home or Leaving Home active)> channel
"Luminaire6ABL LC5-Dimminging Direction CD 6" set > value to "minimize"
> channel "Luminaire7ABL RB1-Dimming Direction CD 7" > value to "minimize"
> channel "Luminaire2SL VLB10 dimming value CD 2" set > value to "100> channel "Luminaire3SL VRB21 dimming value CD 3" > value to "100"
> channel "Vehicle menu operation-menu_display_charisma" set > value to "not active> channel "Vehicle menu operation-
menu_display_charisma_clamp_15_off" set > value to "not active> channel "Vehicle menu operation-menu_display_charisma_over_threshold_high" set >
value to "not active> channel "Vehicle menu operation-menu_display_charisma_standstill" > value to "not active> channel "Vehicle menu operation-
menu_display_charisma_after_disclaimer" > value value set to "not active"
00 Highline
01 Hybrid
02 GTD
03 GTI
04 Bluemotion
05 E-Golf
06 R-Line
07 R
Set STG 5F > adjustment > channel "Developer Mode" > value to "enabled"
01 Highline
02 GTI/GTD/R
> channel "Dynamic flashing mode ZV_Blinken_zu" set > value to "active> channel "Dynamic flashing mode ZV_Blinken_auf" > value to "active> channel
"Luminaire22BR MA57 light function B 22" > value to "Active flashing function has an assigned bit set to 1 in pa_dynamisch_blinken"
> channel "Dynamic flashing mode Warnblinken_Zuendung_EIN" set > value to "active"
> channel "Dynamic flashing mode Warnblinken_Zuendung_AUS" > value to "active"
> channel "Luminaire22BR MA57 light function B 22" > value to "Active flashing function has an assigned bit set to 1 in pa_dynamisch_blinken"
> channel "Luminaire22BR MA57 light function C 22" > value to "Flashing left dark phase"
> channel "Luminaire22BR MA57 light function D 22" set > value to "Flashing right dark phase"
> channel "Luminaire22BR MA57-Dimming Direction CD 22" set > value to "minimize"> channel
"Luminaire22BR MA57 light function E 22" set > value to "brake light"
> channel "Luminaire22BR MA57 dimming value EF 22" > value to "100"
DWA - Activation of the horn acknowledgement when locking and unlocking the vehicle
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Lock feedback signals-acoustic return message" > value to "yes> channel "Lock feedback signals-acousticreturn message" set > value to "yes" >
channel "feedback signal menu control acoustic returnmessage" set > value to"active"
> channel "feedback signals-acoustic return message global" set > value to "aktiv"
> channel "R Ückmeldungssignale-Akustische Rueckmeldung Signalhorn" set > value to "active"n
as required, also
> channel "Fernlicht_Assistent Assist driving lights: sensitivity adjustable via BAP" change > value to "present"
> channel "Fernlicht_Assistent menu control high beam assistant" change > value to "present"
> channel "Fernlicht_Assistent menu control high beam assistant factory setting" change > value to "existing"
> bytes 19 > set bit 0-3 to "00 additional high beam not installed"
> byte 19 > bit 4-7 to "30 version headlight (for FLA): LED with var. Set Light Distribution"
> bytes 21 > bit 5-7 to "40 Dynamic Light Assist (DLA)"
STG 55 > activate encoding > byte 04 > bit 6 ("Masked continuous running light (MDF) active/activated")
> channel "Fernlicht_Assistent Advanced High Beam Control" change > value to "AFS: FLA: High Beam (GLW:MDF)"
> channel "Fernlicht_Assistent Assistance Driving Lights: Sensitivity adjustable via BAP" change > value to "present"
> channel "Fernlicht_Assistent menu control High beam assistant" change > value to "exist"
> channel "Fernlicht_Assistent menu control High beam assistant factory setting" change > value to "exist"
> enable byte 10 > bit 6 ("Masked continuous running light (MDF)active/unlocked")>
byte 10 > bit 7 ("Moving headlight range control(GLW) active/unlocks")activate > byte 08 > bit 1 (if error occurs in MFA)> enable byte 09 > bit 4 (if error
occurs in MFA)
After completion of the coding, a basic adjustment of the headlights must be carried out.
> channel "Volume speaker for front parking aid" adjust > value accordingly (factory setting: 3)> channel "Volume speaker for rear parking aid" adjust >
value accordingly (factory setting: 6)
> channel "Frequency speaker for front parking assistance" adjust > value accordingly (factory setting: 6)> channel "Frequency speaker for rear parking
assistance" adjust > value accordingly (factory setting: 3)
Electronic Parking Brake (EPB) - Deactivation of automatic activation when belts are used
STG 03 > access authorization: 37202 > adjustment > channel "Request belt buckle" set > value to "not active"
ESP - Change available modes (ASR off / ESC Sport / ESC off)
STG 03 > encoding > bytes 29 > value as a hexadecimal number accordingly
> channel "Vehicle function list CAN-driving school" set > value to "vavailable"
> channel "Vehiclemenuoperationmenu_display_driving_school" set > value to "aktiviert"> channel
"Vehiclemenu operationmenu_display_driving_school_over_threshold_high" > value to "aktiviert"
Window operation - Do not cancel release tracking when opening the door
STG 09 > access authorization: 31347 > adjustment > channel "Access control 2-Release follow-up FH abort at tueroeffnen" set > value to "not active"
STG 09 > access authorization: 31347 > adjustment > channel"Assistance light functions-menu control high-beam assistant" set > value to "available"
STG 09 > encoding > byte 02 > bit 0-2 to "03 Bi-Xenon Headlight with Light Assist"
Set STG A5 > encoding > bytes 02 > bit 0-7 to "01 coding_Light_Assist High_Beam_Assist"
> channel "Fernlicht_ Assistent menu control high beam assistant" set > value to "available> channel "Fernlicht_Assistent menu control high beam assistant
factory setting" > value to "available> channel "Fernlicht_Assistent-Erweiterte_Fernlichtsteuerung" set > value to "AFS: FLA: BCM high beam" or"AFS: FLA:
high beam over AFS"
Set STG A5 > encoding > bytes 21 > bit 5-7 to "20 AFS_coding_Light_Assist.High_Beam_Assist"
> "High Beam Assist Activation Speed" channel adjust > value in km/h (factory setting: 57)
> "High Beam Recommendation Speed Threshold" channel > value in km/h (factory setting: 27)
> channel "Body height wheel arch edge front left" correct > value
> channel "body height wheel arch edge front right" correct > value> channel
"body height wheel arch edge rear left" correct > value> channel
"body height wheel arch edge rear right" correct > value
Windscreen wipers - Parking when ignition is switched off (Octavia III 5E)
StG 09 > Disable > Wiper Encoding (WWS) > Byte 01 > Bit 4
> channel "Vehicle Function List BAP-wiper_comfort_0x0C"set > value to "activated"> channel
"VehicleMenu Operation-menu_display_wiper"set > value to "activated"
> channel "Vehiclemenu control-menu_display_wiper_over_threshold_high"> value to "activated"
> "Wipe Speed Continuous Wipe Level 1 Cycles per Minute" channel adjust > value (factory default: 40)> channel "Wipe Speeds Continuous Wiping Level 2
Cycles per Minute" adjust > value (factory default: 60)> channel "Wiping speed-Reduced wiping speed Cycles per minute" adjust > value (factory setting: 30)
STG 09 > access authorization: 31347 > adjustment > channel "Windscreen wiper traen wiper front status" set > value to "active"
> channel "Interior lighting menu control Ambient lighting effect lighting" > value to "active> channel"Luminaire30FR LC72 load type 30" change > value to
"36 - LED small power" (for LED) or "18 - 2* 5W" (for incandescent lamps> channel "Luminaire30FR LC72 light function A 30" change > value to "Footwell
light> channel "Luminaire30FR LC72 dimming value AB 30" > value to"100"
> channel "ambient_lighting_lin_slaves_modules pa_verbauinfo_slave_14" change > value to "built-in> channel "ambient_lighting_lin_slaves_groups-
pa_verbauinfo_gruppe_14" change > value to "3_not_defined> channel"luminaire30FR LC72 load type 30" change > value to "general LED up to 12W>
channel "luminaire30FR LC72 light function A 30" change > value to "footwell light> channel "luminaire30FR LC72 dimming value AB 30" change > value to
"127"
> channel "Indoor Light Luminaire Configuration Footwell Lighting" change > value to "installed"> channel
"Interiorlight 2nd generation default value Ambient profile footwell" change > value to "20%"
> channel "Control by switch for tailgate remote release tip function when closing" set > value to "active> channel "Control by button for tailgate opening
Radio key tip function when closing" set > value to "active"
or
> channel "Control by switch for tailgate remote release key function when closing" set > value to "active> channel"Control by button for tailgate opening
Radio key touch function when closing" set > value to "active"
The tactile function is the long keystroke, while the typing function is the short press.
> channel "Monitoring on keys in the trunk" set > value to "active"
> channel "Warning tone for keys in the trunk" set > value to "active"> channel "Behavior with keys in the trunk during closing" > value to "open"
Tailgate (electric) - Do not break off closing when leaving close range
STG 6D > access authorization: 12345 > adjustment > channel "Close with FFB, exit when leaving the close range" adjust >value
Tailgate (electric) - Allow closing with the key from a greater distance
STG 09 > access authorization: 31347 > adjustment > channel "Close soft top operating range limit for servo rear" > value to "not active"
or
> channel "Warning signal when closing with button in the interior or via radio key" set > value"not activated> channel "Warning signal when opening with
button in the interior or via radiokey" set >value "not activated"
Tailgate lights remain on when flap is opened (Golf 7 AU, Audi A3 8V)
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Luminaire27NSL RC6 light control HD AB 27" change > value to "Always" (factory default: only_if_closed)> channel "Luminaire26NSL LA72-Light
Control HD AB 26" change > value to "Always" (factory default: only_if_closed)
Rear wiper - automatically activate when the front wiper is active at level 2 or higher
STG 09 > access authorization: 31347 > Adjustment > channel "Rear window wiper automatic rear wiping" change > value to "active"
> channel "Rear Window Wiper Comfort Wiper Rear Interval Break Time Level Interval)" adjust > value (factory setting: 7, Maximum: 14)> channel
"Rearwindow wiper comfort wiper rear Interval break time Level Automatic)" adjust > value (factory setting: 7, Maximum: 14)
> Apple_DIO_Wireless channel, change > value to "on> "Vehicle Configuration wlan_5ghz_switch" channel > value to "enabled"
> channel "Luminaire25KZL HA59 load type 25" change > value to "43 - general LED> channel "Luminaire25KZL HA59 dimming value AB 25" change > value
to "127"
KESSY - Automatic locking when closing the doors (3Q0 control unit)
If the customization channel does not exist, it should be omitted.
STG 05 > adjustment > channel "internal_passive_entry_exit_byte1-passive_exit_door_slam_lock" set > value to "active"
KESSY - Automatic locking when closing the doors (5Q0 control unit)
The automatic mirror folding does not work in this way. The fuel filler flap is also notlocked. If the customization channel does not exist, it should be omitted.
STG 05 > adjustment > channel "internal_passive_entry_exit_byte1-passive_exit_door_slam_lock" set > value to "active"
> DeveloperCoding: Search lights-ZAT_illumination_concept_mybeat_clamp58xt channel, change > value to enabled> DeveloperCoding: Search lights-
ZAT_illumination_modus_mybeat_clamp58xt channel, change > value to enabled
STG 09 > access authorization: 31347 > adjustment > channel "Opening access control 2-Kessy Comfort" > value to "active"
> internal_passive_entry_exit_byte2 lf_shutdown channel, set > value to enabled> lf_shutdown_timeout_2nd_operation channel > value to 5 (or desired
timeout)
> channel "DeveloperCoding: Passive Entry Exit (Byte 2)-lf_shutdown" set > value to "activated> channel "lf_shutdown_timeout_2nd_operation" set > value
to "5" (or desired timeout)
STG 05 > adjust > channel "Byte9_VIP-Coding_easyclose_locking" set > value to "activated"
STG 08 > enable encoding > bytes 15 > bit 5 ("filtering recirculating air")
"00 blower logic with manual adjustment,manual offset"> Adjustment reduces/expands the current level, AUTO mode remains active"10
Blower logic with manual adjustment,Blower stage: absolute"> The adjustment sets the new level and deactivates the AUTO mode
Air conditioning - display blowertest ufe also in AUTO mode (not Audi A3 8V)
STG 08 > set encoding > bytes 11 > bit 6 -7 to "40 blower display in auto operation,activated"
All Y-values must be adjusted. These can all be set to a value, or the curve can be recreated.
All Y-values must be adjusted. These can all be set to one value, or the curve can befollowed.
All Y-values must be adjusted. These can all be set to a value, or the curve can be recreated.
All Y-values must be adjusted. These can all be set to avalue, or recreate the curve
STG 08 > adjustment > channel "Blower logic with manual adjustment" set > value to "Offset Manual"
or
Subsequently, the factory setting may have to be restored via the CAR-Menü,only thendoes the changed flashing cycle work!
SET STG 08 > encoding > bytes 13 > bit 2-3 to "08 steering wheel heating car mode,outside temperature"
STG 44 > access authorization: 19249 > adjustment > channel "SteeringAssistance" adjust > value (100%, 80%, 60%, 40% or 20%)
Adjust steering assistance directly when changing driving profiles (instead of incremental changes)
STG 44 > access authorization: 28183 > Adjustment > channel "Driving profileswitching" Change > value to "Direct" (factory setting: step-by-step: controlled
over time)
> channel "Luminaire12NL LB45 light function C 12" change > value to "Light horn generally> channel "Luminaire12NL LB45 dimming value CD 12" change >
value to "127> channel "Luminaire13NL RB5 light function C 13 " change > value to "Light horn in general> channel "Luminaire13NL RB5 dimming value CD
13" change > value to "127"
and if desired
> channel "Luminaire12NL LB45 light function D 12" change > value to "High beam left" > channel "Luminaire13NL RB5 light function D 13" change > value to
"High beam right"
> channel "Luminaire12NL LB45 light function E 12" set > value to "Light horn in non-active dipped beam and non-active continuous running light"
> channel "Luminaire12NL LB45 dimming value EF 12" set > value to "100"> channel "Luminaire13NL RB5 light function E 12" set > value to "Light horn in
non-active low beam and non-active continuous running light> channel "Luminaire13NL RB5 dimming value EF 12" set > value to "100" > channel
"Luminaire6ABL LC5 light function B 6" > value set to "Light horn with already active low beam or already active continuous running light> channel
"Luminaire7ABL RB1 light function B 7" set > value to "Light horn with already active low beam or already active continuous running light"
> channel "Luminaire 8FL LB39-Lichtfunktion E 8" > value to "Light horn in case of non-active dipped beam and non-active continuous running light> channel
"Luminaire8FL LB39 dimming value EF 8" set > value to "100> channel "Luminaire9FL RB2 light function E 9" set > value to "Light horn in non-active low
beam and non-active continuous running light> channel "Luminaire9FL RB2 dimming value EF 9" set > value to "100"
> "Comfort Lighting-Coming Home Installation Status" channel, set > value to "automatic> channel "Comfort lighting menu control Coming Home Factory
setting" set > value to "active> channel "Comfort lighting menu setting Cominghome" set > value to "30 s> channel "Comfort lighting-Coming Home lights"
set > value to "dipped beam> channel "Comfort lighting coming-home switch-on event" > value to "Driver door> channel "Comfort lighting brightness
threshold Infrared measurement" set > value to "12 lx" or "3"> channel "Comfort lighting-Leaving-Home Installation status" set > value to "released>
channel "Comfort lighting menu control Leaving-home Activation via BAP" set > value to "active> channel "Comfort lighting menu setting Leaving-home time
via BAP" set > value to "30 s> channel "Comfort lighting brightness threshold Forward measurement" > Set value to "46400 lx" or "112"
The adjustments must be checked and, if necessary, adapted to ensure flawless functionality.
STG 09 > enable encoding > RLFS > bytes 00 > (bit 1 and) bit 2
The encoding of bit 2 is not assumed, with bit 1 it works. The coding for the »RLHS« is not known.
Valuediffers slightly from theamount of fuel to be refuelled. Display in the MFA takes place in 5 l steps!
At speeds above this value, a message is displayed in the MFA that the NSL should be turned off.
> "Vehicle Function List CAN-MFL" channel, set > value to "available"
> channel "Vehicle function list BAP-MFL_0x0F" set > value to "activated"
> channel "Vehicle function list BAP-MFL_Jocker_0x34" set > value to "activated"
> channel "Vehicle menu operation menu_display_MFL_jocker" set > value to "activated"
> channel "Vehicle menu operation menu_display_MFL_jocker_over_treshold_high" > value to "activated"
> channel "Luminaire12NL LB45 load type 12" set > value to "10 - general headlights> channel "Luminaire12NL LB45 lamp defect bit position 12" set > value
to "38> channel "Luminaire12NL LB45 fault location average byte DTC-DFCC 12" > value to "22> channel"Luminaire12NL LB45 light function A 12" set > value
to "fog light left> channel "Luminaire12NL LB45 light function B 12" > value to "Left corner> channel "Lamp12NL LB45 dimming value AB 12" > Set value to
"100> channel "Luminaire13NL RB5 load type 13" set > value to "10 - general headlights> channel "Luminaire13NL RB5 lamp defect bit position 13" > value
to "42> channel "Luminaire13NL RB5 fault location average byte DTC-DFCC 13" set > value to "23> channel "Luminaire13NL RB5 light function A 13" set >
> channel "Luminaire12NL LB45 light function B 12" adjust > value to "Left cornering light> channel "Luminaire13NL RB5 light function B 13" adjust > value
to "Right cornering light"
> channel "Static cornering light regulation" set > desired regulation
activate > byte 05 > bit 0 (predictive route data,unlocked)activate > byte 05 > bit 1 (intersection light with route data, unlocked)
or
activate > byte 11 > bit 0 (predictive route data unlocked)> byte 11 > bit 1 (intersection light with route data unlocked)
> channel "Luminaire8FL LB39 load type 8" set > value to "6 - LED light module> channel "Luminaire9FL RB2 load type 9" set > value to "6 - LED light module"
> channel "Luminaire12NL LB45 load type 12" set > value to "6 - LED light module> channel "Luminaire13NL RB5 load type 13 " > value to "6 - LED light
module".
> Byte 08 > Bit 2 aktivieren (Personalization profiles active)> Byte 11 > Bit 4-6 auf "10 Profil_Variante,Konto (v. 1.x)"
STG 08 > set encoding > bytes 15 > bit 3-4 to "08 personalization,enabled"
SET STG 36 > encoding > bytes 09 > bit 1-2 to "02 Func_key_memory_personalization,personalization active"
> Personalization Aktivierungsoption_im_HMI Menue_sichtbar channel, adjust > value to active> PersonalizationAnzahl_Benutzerkonten channel, adjust >
value to 4>Personalization Benutzerkontenverwaltung_in_HMI Menue_sichtbar channel, adjust > value to active> Personalization Personalisierung_aktiv
channel, adjust > value to active> Personalization Personalisierungsfunktionen_in_HMI Menue_sichtbar channel > value on "active" adjust
> channel "Personalization Personalisierung_Profilfunkion" adjust > value to"profiles_active"
> channel "Personalization Profil_Variante" adjust > value to"Account (v. 1.x)"
> channel "Personalization PSO_FSG_Setup2_Bit_1" > value to "active " adjust value to "active"
> channel "Personalization PSO_FSG_Setup2_Bit_ 2" adjust > value to "active"
> channel "PersonalizationPSO_FSG_Setup2_Bit_3" adjust > value to "active" (only if STG 36 is installed)> channel"Personalization PSO_FSG_Setup2_Bit_4"
> value to "not active"
STG 08 > set encoding > bytes 15 > bit 3-4 to "08 personalization,enabled"
STG 36 > set encoding > bytes 09 > bit 1-2 to "02 Func_key_memory_personalization,personalization active"
Set STG A5 > encoding > bytes 13 > bit 3-5 to "10 Personalized_key,Version_1.x"
> channel "Luminaire16BLK SLB35BLK SL KC9 light function A 16" adjust > value to "Flashing left dark phase" (factory setting: light phase)
> channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function A 17" adjust > value to "Flashing right dark phase"n (factory setting: light phase)
Pace-Car Flashing of the tail lights (only when opening/closing the vehicle) (LED taillights) (Golf 7 AU)
STG 09 > access authorization: 31347 > adaptation > ...
Pace-Car Flashing of the tail lights (only when hazard lights are flashing) (LED taillights) (Golf 7 AU)
STG 09 > access authorization: 31347> Adaptation > ...
> channel "Dynamic flashing mode Warnblinken_Zuendung_EIN" set > value to "active> channel "Dynamic flashing mode Warnblinken_Zuendung_AUS" >
value to "active> channel "Luminaire16BLK SLB35BLK SL KC9 light function C 16" > set value to"Active flashing function has an assigned bit set to 1 in
pa_dynamisch_blinken" > channel "Luminaire16BLK SLB35BLK SL KC9 dimming value CD 16" set > value to "100> channel "Luminaire16BLK SLB35BLK SL KC9
light function E 16" set > value to "Flashing right light phase> channel "Luminaire16BLK SLB35BLK SL KC9 dimming value EF 16" set > value to "0> channel
"Luminaire16BLK SLB35BLK SL KC9-Dimming Direction EF 16" set > value to "minimize> channel "Luminaire17TFL R BLK SRB3TFL R BLK SLK SR KC3 > > value
to " Active flashing function has an assigned bit set to 1 in pa_dynamisch_blinken" set> channel"Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value
CD 17" set > value to "100> channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function E 17" set > value to "Flashing left light phase> channel
"Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value EF 17" set > value to "0> channel "Lamp17TFL R BLK SRB3TFL R BLK BLK Set SR KC3-Dimming
Direction EF 17" > value to "minimize"
STG 09 > access authorization: 31347 > Adjustment > channel"Driving light and parking light activated via LSS" change > value to "both sides" (factory setting:
one-sided)
> Audio Management Input Amplification Radio(FM) channel, adjust > value to "127" (factory default: -127)adjust > audio management input amplification
radio (AM) channel > value to "127" (factory default: -127)adjust > channel "Audio Management Input Amplification Digital Radio(DAB)" > value to
"127"(factory default: -127)
> channel "Vehicle Function List BAP-tire_pressure_system_0x07" set > value to "activated> channel "Vehicle Function List BAP-
tire_pressure_system_0x07_msg_bus" > value to "Data Bus Extended"
> "Write Sensor Identification Number-Wheel Position" channel, set > value to "Rear Right"
After completion of the coding, parameters for the tire pressures must be generated and uploaded with VCP or similar. The TPMS tool of jolt can be used to
create the parameters.
> channel "Vehicle Function List BAP-tire_pressure_system_0x07" set > value to "active"
> channel "Vehicle function list BAP-tire_pressure_system_0x07_msg_bus" set > value to "Chassis Data bus"
> channel "Vehicle menu operation menu_display_rdk" set > value to "active"
> channel "Vehicle menu operation menu_display_rdk_over_treshold_high" set > value to "active"
STG 17 > enable encoding > bytes 04 > bit 0 ("Indirect Tire Pressure Monitoring System (TPMS)")
> channel "Luminaire28RFL LC11 dimming value AB 28" set > value to "100" (factory setting:86)>
channel "Luminaire29RFL RA64 dimming value AB 29" set > value to "100" (factorysetting: 86)
enable > byte 01 > bit 1> enable byte 01 > bit 2
Sunroof - Do not abort the closing process when the door is opened (with STG CA)
Enable STG CA > encoding > bytes 00 > bit 6 ("Continue_closing_movement_without_BCM_FH_Freigabe")
Sunroof - Do not break off the closing process when the door is opened (without STG CA)
StG 09 > Enable encoding > sunroof (J245 PS24.402) > Byte 00 > Bit 7
STG CA > adjustment > channel "Comfort functions-target position when opening comfort" change > value to "Sliding position" (factory setting: display
position)
Sunroof - Decouple roller blind from the roof (with STG CA)
Disable STG CA > encoding > bytes 02 > bit 6
Sunroof - Decouple roller blind from the roof (without STG CA)
STG 09 > disable encoding > sunroof roller blind (J394 PS24.402) > bytes 00 > bit 0
Tail light Inside Double function as brake light (for LED taillights) (Golf 7 AU)
STG 09 > access authorization: 31347 > adaptation > ...
> channel"Luminaire27NSL RC6 light function C27" set > value to "Brake light" (factory setting: nnot active)> channel "Luminaire27
NSL RC6 dimming value CD27" set > value to "100"(factory setting: 0)
Tail light Inside Double function as brake light (for halogen taillights) (Golf 7 AU)
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Luminaire23SL HLC10 light function C23" set > value to "Brake light" (factory setting: not active)> channel"Luminaire23SL HLC10_Dimmwert
CD23" set > value to "100" (factory setting: 0)> channel "Luminaire24SL HRA65 light function C24" set > value to "Brake light" (factory setting: not active)>
channel "Luminaire24SL HRA65_Dimmwert CD24" > Value to "100" (factory setting: 0)
Tail light Indoor Deactivate double function as brake light when the rear fog lamp is active (legally. Edition according to StVZO)
STG 09 > access authorization: 31347 > adaptation > ... (Example of LED taillights)
> channel "Luminaire27NSL RC6 light function E 27" set > value to "Rear fog light when no trailer plugged" (factory setting: not active)>
channel"Luminaire27NSL RC6 dimming value EF 27" set > value to "10"(factory setting: 0)> channel "Luminaire27NSL RC6-Dimming Direction EF 27" set >
value to "minimize" (factory setting: maximize)
Seats - Comfort entry "Easy Entry" Activate menu item (electric seats)
STG 36 > encoding > ...
© 2013-2021 Daniel Fuchs Side 64
> Enable byte 09 > bit 6 (easy_entry_front_over_MMI)enable > byte 06 > bit 4 (EasyEntry_Enable_Passenger_over_DriverMMI) (only run if STG 06 is
installed)
> channel "Allocation of current consumption for seat heating levels seat heating level 1 lower switching threshold" adjust > value in °C> channel "Allocation
of current consumption for seat heating levels seat heating level 1 upper switching threshold" adjust > value in °C> channel "Allocation of current
consumption for seat heating levels seat heating level 2 lower switching threshold" adjust > value in °C> channel "Allocation of current consumption for seat
heating steps seat heating level 2 upper switching threshold" > Adjust value in °C> channel "Allocation of current consumption for seat heating levels seat
heating level 3 lower switching threshold" adjust > value in °C> channel "Allocation of current consumption for seat heating levels seat heating level level 3
upper switching threshold" adjust > value in °C> channel "Allocation of current consumption for seat heating levels seat heating level 4 lower switching
threshold" adjust > value in °C> channel "Allocation of current consumption for seat heating levels seat heating level 4 upper switching threshold"> channel
"Allocation of current consumption for seat heating levels seat heating level 4 upper Switching threshold" adjust > value in °C> channel "Allocation of
current consumption for seat heating levels seat heating level 5 lower switching threshold" adjust > value in °C> channel "Allocation of current consumption
for seat heating levels seat heating level 5 upper switching threshold" adjust > value in °C> channel "Allocation of current consumption for seat heating
levels seat heating level 6 lower switching threshold" adjust > value in °C> channel "Allocation of current consumption for seat heating stages seat heating
level 6 lower switching threshold" adjust value in °C> channel "Allocation of current consumption for seat heating stages seat heating level 6 lower switching
threshold" Seat heating level seat heating level 6 upper switching threshold" adjust > value in °C
Depending on the vehicle, different levels are used. On the Octavia III and Golf 7, levels 1 and 2, 3 and 4, and 5 and 6 are the same. With the Leon 5F, only levels
2, 4 and 6 are occupied.
> channel "Storage of the seat heating level driver" set > value auf "aktiv" or "aktiv for 10 minutes"> channel
"Storage of the seat heating level passenger" set > value to "aktiv" or "aktiv for 10 minutes"
After successful encoding, check the box for "Set daylight saving time automatically" in the CAR menu under "Time and date"
Sound system - Extension of the internal sound system (without ext. Amp) around virtual surround and subwoofer
STG 5F > encode > bytes 11 > to "04" (Sound_System_internal_individual)
> channel "Access control 2-mirror lowering when returning" set > value to "active> channel "Access control 2-menu control mirror lowering" set > value to
"active"
Enable STG 52 > encoding > bytes 04 > bit 2 and bit 3
> Byte 04 > Bit 4 aktivieren ("Foldable Mirrors installed")> Byte 04 > Bit 6 aktivieren ("Comfort Mirror Folding active")
"by look command via remote control key"> mirrors fold up immediately when locking via FFB"convenience operation via remote control key"> mirrors only
fold when the locking button on the key is pressed for 2-3 seconds
Mirror - Activate heating automatically when activating the rear window heater
STG 42 > enable encoding > bytes 09 > bit 2 ("rear_window_heater_trigger,active")STG 52 > enable encoding > byte 09 > bit 2
("rear_window_heater_trigger,active")
STG A5 > enable encoding > bytes 00 > bit 0 ("Lane Keeping Assist (HCA) active/installed")
> channel "Vehicle Function List BAP; Erweiterung_LDW_HCA_0x19" set > value to "activated"
> channel "Vehicle function list BAP; Erweiterung_LDW_HCA_0x19_msg_bus" set > value to "Data Bus Extended> channel "Vehicle Menu Operation-
menu_display_Lane_Departure_Warning" set > value to "activated"
> channel "Vehicle Menu Operation-menu_display_Lane_Departure_Warning_over_threshold_high" > Set to "activated"
activate > byte 04 > bit 6 ("Lane Assist / Lane Assist installed")> activate byte 11 > bit 1 ("Lane Keeping Assist / Lane Assist Information (BAP)
installed/active")
STG 44 > access authorization: 19249 > activate encoding> byte 00 > bit 4 ("Lane Keeping Assist installed")
STG A5 > enable encoding > bytes 16 > bit 7 ("Lane Keeping Assist (HCA) active/installed [PR-7Y9]")
> channel "Personalization Intervention time at class 15" set > value to "Last setting> channel "Personalization BAP" set > value to "not active> channel
"Switch-on state Lane Departure Assist" > value to "on (setting via menu)"
> Car_Function_List_BAP_Gen2 LDW_HCA_0x19 channel, set > value to enabled> Car_Function_List_BAP_Gen2 LDW_HCA_0x19_msg_bus channel set >
value to Data Bus Extended> Car_Function_Adaptations_Gen2 menu_display_Lane_Departure_Warning channel > value to enabled>
Car_Function_Adaptations_Gen2 menu_display_Lane_Departure_Warning_over_threshold_high channel > value to enabled
activate > byte 04 > bit 6 ("Lane Keeping Assist / Lane Assist installed")> activate byte 11 > bit 1 ("Lane Keeping Assist / Lane Assist Information (BAP)
installed/active")
STG 44 > access authorization: 19249 > activate encoding > bytes 03 > bit 0 ("Lane Keeping Assist installed")
STG 10 > access authorization: 71679 > activate encoding > byte 03 > bit 5 ("Lane Keeping Assist with steering assistance installed")
> set byte 08 > bit 5-7 to "A0 Point_of_intervention.late_setting_over_menu> set byte 09 > bit 0-1 to "03
Configuration_for_lane_departure_warning_Kl15.Last_setting> set byte 09 > bit 2-3 to "0C Lane_assist_system_mode.Selection_over_menu"
> enable byte 09 > bit 7 ("HC, 0=not_coded / 1=coded")>
enable byte 17 > bit 0 ("Hc_messages.0=not_coded / 1=coded")> set byte 17 > bit 1-3 to "02 HC_Warn_Intensity.Setting_over_Menu> set bytes 17 > bit 5-7
to "20 Hc_variante.Variante_1" or "00 Hc_variante.Variante_ 0"
> Car_Function_List_BAP_Gen2 LDW_HCA_0x19 channel, set > value to enabled> Car_Function_List_BAP_Gen2 LDW_HCA_0x19_msg_bus channel set >
value to Data Bus Extended> Car_Function_Adaptations_Gen2 menu_display_Lane_Departure_Warning channel > value to enabled>
Car_Function_Adaptations_Gen2 menu_display_Lane_Departure_Warning_over_threshold_high channel > value to enabled
activate > byte 04 > bit 6 ("Lane Assist / Lane Assist installed")
> activate byte 11 > bit 1("Lane Keeping Assist / Lane Assist Information (BAP) installed/active")
STG 44 > access authorization: 19249 > activate encoding > bytes 03 > bit 0 ("Lane Keeping Assist installed")
STG 10 > access authorization: 71679 > activate encoding > byte 03 > bit 5 ("Lane Keeping Assist with steering assistance installed")
Lane Keeping Assist - Activate adaptive lane guidance via steering column button
A front/apron cameracontrol unit with part number 3Q0 isrequired. After coding, adaptive lane guidance can be switched on and off by holding down the lane
button on the steering column.
Lane Keeping Assist - Set the time of intervention via the menu
Set STG A5 > encoding > bytes 14 > bits 5-7 to "A0 Time of intervention: late (setting via menu)"
© 2013-2021 Daniel Fuchs Side 70
Lane Keeping Assist - Adjust the intensity of the steering wheel vibration
STG A5 > access authorization: 20103 > adjustment > channel "Intensity steering wheel vibration" adjust > value accordingly(factory setting: medium)
STG A5 > encoding > byte 09 > bit 0-1 to "03 Configuration_for_lane_departure_warning_Kl15.Last_setting"
STG A5 > access authorization: 20103 > adjustment > channel "HCA_Warning_Intensity" set > value to "Menu"
or.
STG A5 > access authorization: 20103 > adjustment > channel "Warning intensity Lane Keeping Assistant" set > value to"Selection via menu"
STG A5 > encoding > bytes 13 > bits 1-2 to "06 System Mode Lane Keeping Assistant, Selection via Menu"
> channel "Control parameters heating-lower temperature threshold ambient temperature" adjust > value in °C> channel "Control parameters heating-
upper temperature threshold Ambient temperature" adjust > value in °C
or
> "Start/Stop Start Voltage Limit" channel, change > value to "12" (factory default: 7.6)
SWRA - Deactiviesyoung
STG 09 > Codierung > Byte 13 > Bit 3 deaktiveren
The entire washing process is split into two separate spraying processes, the times can be adjusted as desired. The longer the washing times, the sooner your
wiping water container is empty!
> channel "Luminaire2SL VL B10 light function E 2" set > value to "Flashing left active (both phases)" (factory setting: not active)
> channel "Luminaire2SL VL B10 dimming value EF 2" set > percentage value as desired (factory setting: 0)
set > channel "Luminaire2SL VL B10-Dimming Direction EF 2" > value to "minimize" (factory setting: maximize)
> channel "Luminaire3SL VR B21 light function E 3" set > value to "Flashing right active (both phases)" (factory setting: not active)
> channel "Luminaire3SL VR B21 dimming value EF 3" set > percentage value as desired (factory setting: 0)set > channel
"Luminaire3SL VR B21-Dimming Direction EF 3" > to "minimize" (factory setting: maximize)
Daytime running lights - Dimming when flashing (slow dimming) (Seat Leon 5F)
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Luminaire2SL VL B10 light function E 2" > value to "Flashing left active (both phases); Dimming up and down with p_t_blinken_rampe" set
> channel "Luminaire2SL VL B10 dimming value EF 2" > percentage value as desired
> channel "Luminaire2SL VL B10-Dimming Direction EF 2" set > value to "minimize"
> channel "Luminaire3SL VR B21 light function E 3" > value to "Flashing right active (both phases); Set the dimming and dimming with p_t_blinken_rampe"
> channel "Luminaire3SL VR B21 dimming value EF 3" > percentage value as desired> channel
"Leuchte3SL VR B21-Dimming Direction EF 3" > set to "minimize"
> channel "Luminaire2SL VL B10 dimming value CD 2" set > value to "100" (factory setting: 30)
> channel "Luminaire3SL VR B21 dimming value CD 3" > value to "100" (factory setting: 30)
Daytime running lights - Simultaneous flashing with the turn signal (or alternating)
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Luminaire2SL VLB10 light function G 2" adjust > value to "Flashing left dark phase> channel "Luminaire2SL VLB10 dimming value GH 2" adjust >
value to "0> channel "Luminaire2SL VLB10 dimming direction GH 2" adjust > value to "minimize> channel "Luminaire3SL VRB21 light function G 3" adjust >
value to "Flashing right dark phase> channel "Luminaire3SL VRB21 dimming value GH 3" > value to "0> channel "Lamp3SL VRB21 dimming direction GH 3" >
value to "0" Customize "minimize"
For alternating flashing, light phase must be set instead of "flashing left/right".
> channel "Luminaire4TFL LB4 light function A 4" set > value to "not active" (factory setting: daytime running lights)
> channel "Luminaire4TFL LB4 light function A 4" set > value to "not active" (factory setting: daytime running lights)
> channel "Luminaire12NL LB45 light function C 12" set > value to "daytime running lights" (factory setting: not active)
Daytime running lights - add fog lights in addition to daytime running lights
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Luminaire12NL LB45 light function B 12" set > value to "Daytime running lights"
> channel "Luminaire13NL RB5 light function B 13" > value to "Daytime running lights"
Daytime running lights - rear lights additionally active (with KZB and interior button = parking light always active)
STG 09 > access authorization: 31347 > Adjustment > channel "Daytime running lights-Daytime running lights Continuous running lights additionally activated
Parking light" set > value to "active"
> channel "Luminaire23SL HLC10 light function D 23" change > value to "Daytime running lights" (factory setting: not active)
> channel "Luminaire24SL HRA65 light function D 24" change > value to "Daytime running lights" (factory setting: not active)
> channel "Luminaire26NSL LA72 light function D 26" change > value to "Daytime running lights" (factory setting: not active)
> channel "Luminaire27NSL RC6 light function D 27" change > value to "Daytime running light" (factory setting: not active)
Daytime running lights - parking light point additionally active (Golf 7 AU)
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Luminaire 8FL LB39-Lichtfunktion C 8" > value set to "Daytime running lights" not active before> channel "Leuchte8FL LB39-Dimmwert CD 8" set
> value to "100" before> channel "Leuchte9FL RB2-Lichtfunktion C 9" > value to "Daytime running lights" do not set active beforehand> channel "Leuchte9FL
RB2 dimming value CD 9" set > value to "100"
Negative values lower the fuel needle, positivevalues lift them. Calculation such as residual rangee are alsoinfluenced.
All Y-values must be adjusted. These can all be set to avalue, or recreate the curve
Set STG A5 > encoding > bytes 16 > bit 2-3 to "08 EA_Variant2"
STG 13 > enable encoding > byte 04 > bit 2 ("Emergency Assist installed")
STG 09 > access authorization: 31347 > adjustment > channel "Auß enlicht_Blinker-Warnblinken_durch_Fahrerassistenz" set > value to "active"
theofr
STG 09 > access authorization: 31347 > Adjustment > channel "Aussenlicht_uebergreifendambient light as manoevrier light" set > value to "active"
> channel "Luminaire 0 BLK VL B36 light function C 0" > value to "Parking light front (position light; Limiting light)> channel "Luminaire 0 BLK VL B36 dimming
value CD 0" set > percentage value as desired (factory setting: 0)> channel "Luminaire1BLK VRB20 light function C 1" > value to "Parking light front (position
light; Limiting light)" set> channel "Luminaire1BLK VRB20 dimming value CD 1" > percentage value as desired (factory setting: 0)
Emulate US parking light via ambient lighting (dimmable/switchable in the CAR menu)
If the coding does not lead to success, it may be becauses"Ambient Light 3" and the "Ambiente_Applikationsleisten_in_Tuertafel" must be used.
> channel "Indoor light luminaire configuration Ambiente_Applikationsleisten_in_Instrumententafel" set > value to "installed"
> channel "Indoorlight configuration ambience menu with global from" set > value to"active> channel
"Leuchte 0 BLK VL B36 light function A 0" set > value to "ambient light 1> channel"Leuchte 0 BLK VL B36-Dimmvalue AB 0" > percentage value as desired
> channel "Lamp 0 BLK VL B36 light function C 0" set > value to "handbrake is tightened"
> channel "Leuchte 0 BLK VL B36 light function D 0" set > value to"interior light"
> channel "luminaire0 BLK VL B36 dimming value CD 0" set > value to "0"
> channel "luminaire 0 BLK VL B36-Dimming Direction CD 0" > value to "minimize"
> channel"Leuchte 0 BLK VL B36-Lichtfunktion F 0" set > value to"Blinking left Light phase" > Channel "Lamp0 BLK VL B36-Dimming value EF 0" set > value
to "100"> channel "Lamp 0 BLK VL B36-Dimming Direction EF 0" set > value to "maximize>channel"Luminaire0 BLK VL B36 light function H 0" set > value to
"Flashing left dark phase> channel "Luminaire 0 BLK VL B36 dimming value GH 0" > value to Set "0> channel "Luminaire 0 BLK VL B36-Dimming Direction GH
0" set > value to "minimize> channel "Luminaire1BLK VRB20-Light function A 0" set > value to "Ambient light 1> channel "Luminaire1BLK VRB20dimming
value AB 0" set > percentage value as desired
> channel "Luminaire1BLK VRB20-Light function C 0"set > value to "Handbrake is tightened"
> channel "Luminaire1BLK VRB20 -Light function D 0" set > value to "indoor light" > channel
Control US parking light via driving profile Sport (Leon III 5F)
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Luminaire 0 BLK VL B36 light function A 0" > Whocan set to "Ambient light 4> channel "Luminaire0 BLK VL B36 dimming value AB 0" set >
percentage value as desired> channel "Luminaire 0 BLK VL B36 light function E 0" set > value to "Flashing left light phase> channel "Luminaire 0 BLK VL B36
dimming value EF 0" > value to "100" (H7) or "127" (LED) > channel "Luminaire1BLK VRB20 light function A 1" > value to "Ambient light 4" set> channel
"Luminaire1BLK VRB20 dimming value AB 1" set > percentage value as desired> channel "Luminaire1BLK VRB20 light function E 1" set > value to "Flashing
left light phase> channel "Luminaire1BLK VRB20 dimming value EF 1" set > value to "100" (H7) or "127" (LED)
and if desired
> channel "Daytime running lights-Daytime running lights Continuous running lights additionally activated parking light" set > value to "active"
The light, just like the ambient lighting, is only active in parking light and dipped beam. The last adaptation allows the light to be used in daytime running lights
as well. The disadvantage here is that both the rear lights and the interior lighting (buttons, etc.) are permanently active.
USdaytime running lights or parking lights (turn signals permanently dimmedin daytime running lights or parking lights/low beams)
STG 09 > access authorization: 31347 > adaptation > ...
> channel "Luminaire 0 BLK VL B36 light function C 0" set > value to "Parking light general" or "Daytime running light" (factory setting: not active)
> channel "Luminaire 0 BLK VL B36 dimming value CD 0" set > percentage value as desired (factory setting: 0)
> channel "Luminaire1BLK VR B20-Light function C 1" > value to "Parking light general" or Set "Daytime running lights" (factory setting: not active)>
Kanal"Luminaire1BLK VR B20-Dimming value CD 1" set > percentage value as desired (factory setting: 0)
The dimming does not work with LED turn signals such as the Golf 7 R or Seat Leon FR 5F.
> channel "Luminaire 0 BLK VL B36-Lichtfunktion E0" set > value to "Blinken left dark phase> channel "Luminaire 0 BLK VL B36-Dimming Direction EF0" set >
value to
"minimize" (factory setting: maximize)> channel
"Leuchte1BLK VR B20-Lichtfunktion E1" set > value to "Blinken right dark phase> K
anal "Leuchte1BLK VR B20-Dimming Direction EF1" > Set value to"minimize" (factory default: maximize)
US daytime running lights in addition to normal daytime running lights - switchable via CAR menu
The coding allows a change between the normal daytime running lights and normal daytime running lights + US daytime running lights in light switch position
»0«. For parking light and low beam you have to decide in the coding for a version.
> channel "Daytime running lights Daytime running lights Activation by BAP or operating sequence possible" > value to "active> channel "Luminaire 0 BLK VL
B36 light function A 0" set > value to "active 100%> channel "Luminaire 0 BLK VL B36 dimming value AB 0" set > value to "0> channel "Luminaire 0 BLK VL
B36 light function C 0" set > value to "Daytime running lights> channel "Luminaire 0 BLK VL B36 dimming value CD 0" set > percentage value as desired>
channel
"L 0 BLK VL B36-Dimming Direction CD 0" set > value to "maximize> channel "Luminaire 0 BLK VL B36-Light function F 0" set > value to "Flashing left light
phase> channel "Luminaire 0 BLK VL B36 dimming value EF 0" > value to "100> channel "Luminaire 0 BLK VL B36-Dimming Direction EF 0" set > value to
"minimize> channel "Luminaire 0 BLK VL B36 light function H 0" > value to "Flashing left dark phase> Channel "Luminaire 0 BLK VL B36 dimming value GH 0"
set > value to "0> channel "Luminaire 0 BLK VL B36-Dimming Direction GH 0" > value to "minimize> channel"Luminaire1BLK VRB20-Lichtfunktion A 1" set >
value to "active 100%> channel "Luminaire1BLK VRB20 dimming value AB 1" > value to "0> channel "Luminaire1BLK VRB20 light function C 1" set > value to
"daytime running lights> channel "Luminaire1BLK VRB20 dimming value CD 1" set > percentage value as desired> Channel "Luminaire1BLK VRB20-Dimming
Direction CD 10" set > value to "minimize> channel "Luminaire1BLK VRB20 light function F 1" set > value to "Flashing left light phase> channel
"Luminaire1BLK VRB20 dimming value EF 1" set > value to "100> channel "Luminaire1BLK VRB20 dimming direction EF 1" set > value to "minimize> channel
"Luminaire1BLK VRB20 light function H 1" set > value to "Flashing left dark phase> channel "Luminaire1BLK VRB20 dimming value GH 1" > value to "0" set >
channel "Luminaire1BLK VRB20-Dimming Direction GH 1" > value to "minimize> channel"Luminaire2SL VLB10 light function A 2" change > value from
"Daytime running lights" to "active 100%> channel "Luminaire3SL VRB21 light function A 3" change > value from "Daytime running lights" to "active 100%>
channel "Luminaire4TFL LB4 light function A 4" > value from "Daytime running lights" to "Terminal 15 with trailing to vehicle standstill> channel "Lamp5 TFL
RB32 light function A 5" > value of Change "Daytime running lights" to "Terminal 15 with trailing until vehicle standstill"
und if desired (then the US lighting is on at parking light/low beam, otherwise always off)
© 2013-2021 Daniel Fuchs Side 79
> channel "Luminaire 0 BLK VL B36-Lichtfunktion D 0" > value to "Parking light general (tail light; Positionslicht; Limiting light)"> channel"Luminaire1BLK
VRB20-Lichtfunktion D 1" > value to "Parking light in general (tail light; Positionslicht; Limiting light)"
US daytime running lights/normal daytime running lights - switchable via CAR menu
The coding allows you to switch between the normal daytime running lights and the US daytime running lights in the »0« light switch position. For parking light
and low beam you have to decide in the coding for a version.
> channel "Daytime running lights daytime running lights Activation viaBAP or operating sequence possible" > value to "active> channel "Luminaire0 BLK VL
B36 light function A 0" set > value to "active 100%> channel "Luminaire 0 BLK VL B36 dimming value AB 0" set > percentage value as desired>
channel"Leuchte 0 BLK VL B36 light function C 0" set > value to "daytime running lights> channel "Luminaire 0 BLK VL B36 dimming value CD 0" > value to
"0> channel " Lamp 0 BLK VL B36-Dimming Direction CD 0" set > value to "minimize> channel "Luminaire 0 BLK VL B36-Light function F 0" set > value to
"Flashing left light phase> channel "Luminaire 0 BLK VL B36 dimming value EF 0" set > value to "100> channel "Lamp 0 BLK VL B36 Dimming Direction EF 0"
set > value to "minimize> channel "Leuchte 0 BLK VL B36 light function H 0" > value to "Flashingleft darkphase". > channel"Luminaire 0 BLK VL B36 dimming
value GH 0" > value to "0> channel "Luminaire 0 BLK VL B36-Dimming Direction GH 0" set > value to "minimize"> channel
"Luminaire1BLK VRB20-Light function A 1" set > value to "active 100%"> channel
"Luminaire1BLK VRB20dimming value AB 1" set > percentage value as desired> channel
"Luminaire1BLK VRB20-Light function C 1" set > value to "daytime running lights"
> channel "Luminaire1BLK VRB20-Dimming value CD 1" set > value to "0"
> channel "Luminaire1BLK VRB20-Dimming Direction CD 10"set > value to "minimize"
> channel "Luminaire1BLK VRB20-Light function F 1" set > value to "Flashing left light phase"
> channel "Luminaire1BLK VRB20dimming value EF 1" set > value to "100"
> channel "Luminaire1BLK VRB20-Dimming Direction EF 1" set > value to "minimize"
> channel "Luminaire1BLK VRB20-Light function H 1" set > value to "Flashing left dark phase"
> channel "Luminaire1BLK VRB20-Dimming value GH 1" set > value to "0"
> channel "Luminaire1BLK VRB20-Dimming Direction GH 1" set > value to "minimize"
und if desired (then the US lighting is off at parking light/low beam,otherwise always on)
> channel "Luminaire 0 BLK VL B36-Lichtfunktion D 0" > value to "Parking light general (tail light; Positionslicht; Boundary light)"> channel"Leuchte1BLK
VRB20-Lichtfunktion D 1" > value to "Parking light in general (tail light; Positionslicht; Limiting light)"
Enable STG A5 > encoding > bytes 01 > bit 0 ("Traffic Sign Recognition (VZE) active")
STG 17 > enable encoding > bytes 05 > bit 2 ("traffic sign recognition installed/active")
> channel "Vehicle Function List BAP-traffic_sign_recognition_0x21" set > value to "activated"
> channel "Vehicle Menu Operation-menu_display_road_sign_identification" set > value to "activated"
> channel "Vehicle Menu Operation-menu_display_road_sign_identification_over_threshold_high" > value to "activated"
STG 82 > enable encoding > bytes 00 > bit 0 ("traffic sign recognition, available")
StG A5 > enable encoding > bytes 16 > bit 4 ("Traffic sign recognition (VZE) active [PR-QR9]")
STG 17 > enable encoding > bytes 05 > bit 2 ("traffic sign recognition installed/active")