0% found this document useful (0 votes)

64 views

How To Design Concrete Structures Using Eurocode 2 - Second Edition

Uploaded by

Paul Organ

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

64 views

How To Design Concrete Structures Using Eurocode 2 - Second Edition

Uploaded by

Paul Organ

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 118

A cement and concrete industry publication

How to Design Concrete

Structures using Eurocode 2
Second edition
A J Bond MA MSc DIC PhD MICE CEng A J Harris BSc MSc DIC MICE CEng FGS R M Moss BSc PhD DIC CEng MICE MIStructE
O Brooker BEng CEng MICE MIStructE MCS T Harrison BSc PhD CEng MICE FICT R S Narayanan FREng
J Burridge MA CEng MIStructE MICE A E K Jones BEng PhD CEng FICE R Webster CEng FIStructE
A S Fraser BEng PhD CEng MICE MIStructE

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
Foreword to second edition
The original series of ‘How To’ guides and the ﬁrst edition of this compendium played an important role in the
introduction of Eurocode 2 in the UK.

The ten design standards, known as the Eurocodes, became mandatory for all public works in 2010. BS 8110 was
withdrawn prior to that, in 2008.

The aim of this publication is unchanged, to make the use of Eurocode 2 as easy as possible by drawing together
in one place key information and commentary required for the design and detailing of typical concrete elements.

The second edition addresses errata and includes new material to represent the latest guidance for designing to
Eurocode 2.

Acknowledgements
The introduction of Eurocode 2 required a substantial effort to ensure that the UK design profession would be
able to use Eurocode 2 quickly, effectively, efﬁciently and with conﬁdence. This publication was possible with the
support from government, consultants and relevant industry bodies that enabled the formation of the Concrete
Industry Eurocode 2 Group (CIEG).

Part of the output of the CIEG project was the technical content for 7 of the 11 chapters in this publication. The
content of the original Chapters 1 and 3 to 8 were produced as part of the project Eurocode 2: transition from UK
to European concrete design standards. This project was part funded by the DTI under the Partners in Innovation
scheme. The lead partner was British Cement Association. The work was carried out under the guidance of the
Concrete Industry Eurocode 2 Group and overseen by a Steering Group of the CIEG (members are listed on inside
back cover). Particular thanks are due to Robin Whittle, technical editor to the CEN/TC 250/SC2 committee (the
committee responsible for structural Eurocodes), who has reviewed and commented on the contents. Thanks are
also due to John Kelly and Chris Clear who have contributed to individual chapters.

The remaining chapters have been developed by The Concrete Centre. Updates made in this second edition are
based on amendments from The Concrete Centre with contributions from Jenny Burridge, Charles Goodchild,
Paul Gregory and Jaylina Rana.

Published by MPA The Concrete Centre

Gillingham House, 38-44 Gillingham Street, London SW1V 1HU
Tel: +44 (0)207 963 8000 www.concretecentre.com

CCIP–060
Second edition, February 2018.
ISBN 978-1-908257-21-5

First edition – CCIP 006 – published December 2006, revised September 2009, January 2011, December 2014
ISBN 1-904818-4-1
Price Group P
© MPA The Concrete Centre.

Permission to reproduce extracts from British Standards is granted by British Standards Institution.
British Standards can be obtained from BSI Customer Services, 389 Chiswick High Road, London W4 4AL.
Tel: +44 (0)20 8996 9001 email: cservices@bsi-global.com

All advice or information from MPA The Concrete Centre is intended only for use in the UK by for those who will evaluate the signiﬁcance and limitations
of its contents and take responsibility for its use and application. No liability (including that for negligence) for any loss resulting from such advice or
information is accepted by MPA The Concrete Centre or its subcontractors, suppliers or advisors. Readers should note that publications from MPA The
Concrete Centre are subject to revision from time to time and should therefore ensure that they are in possession of the latest version. Part of this
publication has been produced following a contract placed by the Department for Trade and Industry (DTI); the views expressed are not necessarily those
of the DTI.

Front cover image: Nash Mills development, Hemel Hempstead. Courtesy of Coinford Construction.

Printed by Michael Burbridge Ltd, Maidenhead.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

Contents
1. Introduction to Eurocodes 1
2. Getting started 9
3. Slabs 23
4. Beams 31
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

5. Columns 39
6. Foundations 53
7. Flat slabs 61
8. Deﬂection calculations 69
9. Retaining walls 77
10. Detailing 89
11. Structural ﬁre design 101

Copyright The Concrete Centre

Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2
1. Introduction to Eurocodes
RSNarayananFREng OBrookerBEng,CEng,MICE,MIStructE%F<L J Burridge MA CEng MIStructE MICE

The Eurocode family

This chapter shows how to use Eurocode 21;with the other Eurocodes.In
particular it introduces Eurocode:Basis of structural design2;and Eurocode 1:
Actions on structures3;and guides the designer through the process of
determining the design values for actions on a structure.

Ma^]ôêhif^gmh_ma^>nkh\h]^llmZkm^]bg*20.4lbg\^ma^gma^raZo^
ôheo^]lb`gb_b\ZgmerZg]Zk^ghp\eZbf^]mh[^ma^fhlmm^\agb\Zeer
Z]oZg\^]lmkn\mnkZe\h]^lbgma^phke]'Ma^fZgr[^g^_bmlh_nlbg`
>nkh\h]^+Zk^lnffZkbl^][êhp'Ma^k^Zk^m^g>nkh\h]^l\ho^kbg`Zeema^
fZbglmkn\mnkZefZm^kbZel!l^^?b`nk^*"'Ma^rZkîkh]n\^][rma^>nkhi^Zg
<hffbmm^^_hkLmZg]Zk]bsZmbhg!<>G"%Zg]aZo^kîeZ\^]^qblmbg`gZmbhgZe
lmZg]Zk]lbg+1\hngmkb^l'

>Z\a\hngmkrblk^jnbk^]mhin[eblaZ>nkh\h]^pbmaZgZmbhgZembme^iZ`^Zg]

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
_hkpZk][nmma^hkb`bgZem^qmh_ma^>nkh\h]^fnlmZii^ZkZlikh]n\^][r
<>GZlma^fZbg[h]rh_ma^]h\nf^gm!l^^?b`nk^+"':GZmbhgZe:gg^q
!G:"fZr[îkh]n\^][rZ\hngmkrb_bmbl\hglb]^k^]maZmma^k^blZg^^]'
Ma^GZmbhgZe:gg^qfnlm[^lhe]lîZkZmêr_khfma^fZbglmZg]Zk]Zg]
lahne][^ZoZbeZ[e^bg>gèbla'Makhnàhnmmablin[eb\ZmbhgbmblZllnf^]maZm
ma^NDGZmbhgZe:gg^q^lpbee[^nl^]'

<hg_eb\mbg`;kbmblaLmZg]Zk]lp^k^pbma]kZpgbgFZk\a+)*)'K^`neZmbhgl
\ho^kbg`[nbe]bg`lZk^Z]ôheo^]fZmm^kZg]`nb]Zg\^]h\nf^gmlhgma^
k^`neZmbhglZee\bm^ma^>nkh\h]^lZlZpZrh_\hfierbg`pbmae^`bleZmbhg'
Ma^nl^h_>nkh\h]^+_hkma^]^lb`gh_\hg\k^m^[nbe]bg`lmkn\mnk^lbl
ma^k^_hk^^qi^\m^]Zemahnàghmh[eb`Zmhkr'?hk[kb]`^Zg]abàpZr
lmkn\mnk^lma^^qi^\mZmbhgblmaZm>nkh\h]^lpbee[^nl^]_hkma^]^lb`gh_
g^pZg]k^_nk[bla^]lmkn\mnk^l'NgmbeZgZll^llf^gm>nkh\h]^blin[ebla^]
ma^pbma]kZpg;kbmblaLmZg]Zk]lpbee[^nl^]_hk[kb]`^Zll^llf^gmphkd'

Benefits of using Eurocode 2

1. The Eurocodes are claimed to be the most technically
advanced codes in the world.
(. The Eurocodes are logical and organised to avoid repetition.
). Eurocode 2 is less restrictivethan fh[l_eki8h_j_i^IjWdZWhZi.
*. Eurocode 2 is more extensive than fh[l_eki8h_j_i^IjWdZWhZi.
+. Use of the Eurocodes will provide more opportunity for designers
to work throughout Europe.
,. In Europe all public works must allow the Eurocodes to be used.

Copyright The Concrete Centre

Figure 1
The Eurocodes Eurocode: Basis of
BS EN 1990, Eurocode:
Basis of structural design
Structural safety,
serviceability and durability
structural design
BS EN 1991, Eurocode 1: This Eurocode underpins all structural design irrespective of the
Actions on structures
Actions on structures material of construction. It establishes principles and requirements for
safety, serviceability and durability of structures. (Note, the correct title
BS EN 1992, Eurocode 2: Concrete
BS EN 1993, Eurocode 3: Steel
is Eurocode not Eurocode 0.) The Eurocode uses a statistical approach
BS EN 1994, Eurocode 4: Composite Design and detailing to determine realistic values for actions that occur in combination with
BS EN 1995, Eurocode 5: Timber
BS EN 1996, Eurocode 6: Masonry each other.
BS EN 1999, Eurocode 9: Aluminium

Geotechnical
Eurocode introduces new definitions (see Glossary) and symbols (see
BS EN 1997, Eurocode 7: BS EN 1998, Eurocode 8:
Geotechnical design Seismic design and seismic Tables 1a and 1b), which will be used throughout this publication to
design
assist familiarity. Partial factors for actions are generally given in this
Eurocode, whilst partial factors for materials are prescribed in their
relevant Eurocode.
Figure 2
Typical Eurocode layout
Representative values
For each variable action there are four representative values. The
principal representative value is the characteristic value and this can be
determined statistically or, where there is insufficient data, a nominal
value may be used. The other representative values are combination,
B frequent and quasi-permanent; these are obtained by applying to the
A C
D characteristic value the factors c 0 , c 1 and c 2 respectively (see Figure 3).
D
A: National title page D: Main text
D
D
A semi-probabilistic method is used to derive the c factors, which vary
B: National Foreword E: Main Annex(es) E depending on the type of imposed load (see Table 2). Further information
F
C: CEN title page F: National Annex
on derivation of the c factors can be found in Appendix C of the Eurocode.

The combination value (c 0 Qk) of an action is intended to take

account of the reduced probability of the simultaneous occurrence of
two or more variable actions. The frequent value ( c 1 Qk) is such that it
should be exceeded only for a short period of time and is used
primarily for the serviceability limit states (SLS) and also the accidental
ultimate limit state (ULS). The quasi-permanent value (c 2 Qk) may be
exceeded for a considerable period of time; alternatively it may be
considered as an average loading over time. It is used for the long-term
affects at the SLS and also accidental and seismic ULS.

Combinations of actions
In the Eurocodes the term ‘combination of actions’ is specifically used
for the definition of the magnitude of actions to be used when a limit
state is under the influence of different actions. It should not be
confused with ‘load cases’, which are concerned with the arrangement
of the variable actions to give the most unfavourable conditions and
are given in the material Eurocodes. The following process can be used
to determine the value of actions used for analysis:
1. Identify the design situation (e.g. persistent, transient, accidental).
2. Identify all realistic actions.
3. Determine the partial factors (see below) for each applicable
combination of actions.
4. Arrange the actions to produce the most critical conditions.

2 --`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

Table 'a
Where there is only one variable action (e.g. imposed load) in a Selected symbols for Eurocode
combination, the magnitude of the actions can be obtained by Symbol Definition
multiplying them by the appropriate partial factors. Gk Characteristic value of permanent action
Qk Characteristic value of single variable action
Where there is more than one variable action in a combination, it is gG Partial factor for permanent action
necessary to identify the leading action (Qk,1) and other accompanying gQ Partial factor for variable action
actions (Qk,i). The accompanying action is always taken as the c0 Factor for combination value of a variable action
combination value. c1 Factor for frequent value of a variable action
c2 Factor for quasi-permanent value of a variable action
Ultimate limit state j Combination factor for permanent actions
The ultimate limit states are divided into the following categories:
EQU Loss of equilibrium of the structure. Table 'bSelected
subscripts
STR Internal failure or excessive deformation of the structure
Subscript Definition
or structural member.
A Accidental situation
GEO Failure due to excessive deformation of the ground.
c Concrete
FAT Fatigue failure of the structure or structural members.
d Design
The Eurocode gives different combinations for each of these ultimate E Effect of action
limit states. For the purpose of this publication only the STR ultimate fi Fire
limit state will be considered. k Characteristic
R Resistance
For persistent and transient design situations under the STR limit w Shear reinforcement
state,the Eurocode defines three possible combinations,which are given y Yield strength
in Expressions (6.10),(6.10a) and (6.10b) of the Eurocode (see Tables ,
and -).The designer (for UK buildings) may use either (6.10) or the less Figure3
favourable of(6.10a) and (6.10b). Representative values of variable actions
Characteristic value of QK

At first sight it appears that there is considerably more calculation

Instantaneous value of Q

required to determine the appropriate load combination;however,with Combination value of c0 QK

experience the designer will be able to determine this by inspection.
Frequent value of c1 QK
Expression (6.10) is always equal to or more conservative than the less
Quasi-
favourable of Expressions (6.10a) and (6.10b).Expression (6.10b) will permanent
value of c2 QK
normally apply when the permanent actionsare not greater than 4.5
times the variable actions (except for storageloads (category E,Table +)
where Expression (6.10a) always applies).
Time

Therefore, for a typical concrete frame building, Expression (6.10b) will Table (
give the most structurally economical combination of actions. Recommended values ofcfactors for buildings (from UKNational Annex)
Action c0 c1 c2
Imposed loads in buildings (see BS EN 1991–1–1)
For members supporting one variable action the combination
Category A: domestic, residential areas 0.7 0.5 0.3
1.25 Gk + 1.5 Qk (derived from (Exp 6.10b))
Category B: office areas 0.7 0.5 0.3
can be used provided the permanent actions are not greater
Category C: congregation areas 0.7 0.7 0.6
than 4.5 times the variable actions (except for storage loads). Category D: shopping areas 0.7 0.7 0.6
Category E: storage areas 1.0 0.9 0.8
Category F: traffic area, vehicle weight < 30 kN 0.7 0.7 0.6
Serviceability limit state
Category G: traffic area, 30 kN < vehicle weight < 160 kN 0.7 0.5 0.3
Thereare three combinations of actions that can be used to check the
Category H: roofs* 0.7 0 0
serviceability limit states (see Tables . and /).Eurocode 2 indicates Snow loads on buildings (see BS EN 1991–3)
whichcombination should be used for which phenomenon (e.g. For sites located at altitude H > 1000 m above sea level 0.7 0.5 0.2
deflection is checked using the quasi-permanent combination).Care For sites located at altitude H < 1000 m above sea level 0.5 0.2 0
should be taken not to confuse the SLS combinations of characteristic, Wind loads on buildings (see BS EN 1991–1–4) 0.5 0.2 0
frequent and quasi-permanent,with the representative values that Temperature (non-fire) in buildings (see BS EN 1991–1–5) 0.6 0.5 0
have the same titles. Key
*See also 1991–1–1: Clause 3.3.2
--`,``,,```,,`,`,`,``,`,,```,`-`-`,

3
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Table 3
Design values of actions, ultimate limit state – persistent and transient design situations (table A1.2 (B) Eurocode)

Combination Expression reference Permanent actions Leading variable action Accompanying variable actions
Unfavourable Favourable Main (if any) Others
Exp. (6.10) g G, j, sup Gk , j , sup g G , j, inf G k , j , inf g Q,1 Qk,1 g Q,1 c 0 ,1 Q k,i
Exp. (6.10a) g G, j, sup Gk , j , sup g G , j, inf G k , j , inf g Q,1 c 0 ,1 Qk,1 g Q,1 c 0 ,1 Q k,i
Exp. (6.10b) jg G, j, sup Gk , j , sup g G , j, inf G k , j , inf g Q,1 Qk,1 g Q,1 c 0 ,1 Q k,i
Note
1 Design for either Expression (6.10) or the less favourable of Expressions (6.10a) and (6.10b).

Table 4
Design values of actions, derived for UK design, ultimate limit state – persistent and transient design situations

Combination Expression reference Permanent actions Leading variable action Accompanying variable actions
Unfavourable Favourable Main (if any) Others
Combination of permanent and variable actions
Exp. (6.10) 1.35 Gk a 1.0 Gk a 1.5c Qk
Exp. (6.10a) 1.35 Gk a 1.0 Gk a 1.5 c 0,1b Qk
Exp. (6.10b) 0.925 d x 1.35 Gk a 1.0 Gk a 1.5c Qk
Combination of permanent, variable and accompanying variable actions
Exp. (6.10) 1.35 Gk a 1.0 Gk a 1.5c Qk,1 1.5 c c 0,i b Q k,i
Exp. (6.10a) 1.35 Gk a 1.0 Gk a 1.5 c 0,1b Qk 1.5 c c 0,i b Q k,i
Exp. (6.10b) 0.925 d x 1.35 Gk a 1.0 Gk a 1.5c Qk,1 1.5 c c 0,i b Q k,i
Key
a Where the variation in permanent action is not considered significant, Gk,j,sup and Gk,j,inf may be taken as Gk c Where the accompanying load is favourable, g Q,i = 0
b The value of c 0 can be obtained from Table NA A1.1 of the UK National Annex (reproduced here as Table 2) d The value of j in the UK National Annex is 0.925

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
Table 5
Design values of actions, serviceability limit states

Combination Permanent actions Variable actions Example of use in Eurocode 2

Unfavourable Favourable Leading Others
Characteristic Gk,j,sup Gk,j,inf Qk,1 c 0 , i Qk,i
Frequent Gk,j,sup Gk,j,inf c 1,1 Qk,1 c 2 , i Qk,i Cracking – prestressed concrete
Quasi-permanent Gk,j,sup Gk,j,inf c 2,1 Qk,1 c 2 , i Qk,i Deflection
Notes
1 Where the variation in permanent action is not considered significant. Gk,j,sup and Gk,j,inf may be taken as Gk 2 For values of c 0, c 1 and c 2 refer to Table 2

Table 6
Example design combinations for deflection (quasi-permanent) derived for typical UK reinforced concrete design

Combination Permanent actions Variable action

Unfavourable Leading
Office Gk a 0.3 b Q k,1
Shopping area Gk a 0.6b Q k,1
Storage Gk a 0.8b Q k,1
Key
a Where the variation in permanent action is not considered significant Gk,j,sup and Gk,j,inf may be taken as Gk b Values of c 2 are taken from UK NA (see Table 2)

4
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
1. Introduction to Eurocodes

Table -
Eurocode 1 Eurocode 1

Reference Title
Eurocode 1 contains within its ten parts(see Table 0) all the
information required by the designer to assess theindividual actions on BS EN 1991-1-1 Densities, self-weight and imposed loads
a structure.It is generally self-explanatory [nmZmm^gmbhgbl]kZpgmhma^ BS EN 1991-1-2 Actions on structures exposed to fire
_Z\mmaZmma^bulk density ofreinforced concretebl 25 kN/m3.Mabl
BS EN 1991-1-3 Snow loads
k^ik^l^gmlk^bg_hk\^f^gmh_+h_ma^\hg\k^m^ohenf^'
BS EN 1991-1-4 Wind actions

BS EN 1991-1-5 Thermal actions

Eurocode 2 BS EN 1991-1-6 Actions during execution

BS EN 1991-1-7 Accidental actions due to impact and explosions

There are four parts to Eurocode 2; Figure 4 indicates how they fit into
the Eurocode system, which includes other European standards. BS EN 1991-2 Traffic loads on bridges

BS EN 1991-3 Actions induced by cranes and machinery

Part 1–1 BS EN 1991-4 Actions in silos and tanks
Eurocode 2,Part 1–1:General rules and rules for buildings;is the
principal part which is referenced by the three other parts.

A[o\[Wjkh[ie\;kheYeZ[( Figure 4
Relationship between Eurocode 2 and other Eurocodes
1. Eurocode 2 is generally laid out to give advice on the basis of
phenomena (e.g.bending,shear etc) rather than by membertypes BS EN 1997 BS EN 1990 BS EN 1998
(e.g.beams,slabs,columns etc). EUROCODE 7 EUROCODE EUROCODE 8
Geotechnical Basis of structural Seismic
2. Design is based on characteristic cylinder strengths Zemahn`a cube design design design

strengthsfZr[^m^lm^]mh\hg_bkf\hg\k^m^\hfiebZg\^'
3. The Eurocode does not provide derived formulae (e.g. for bending,
BS EN 206 BS EN 1991 BS EN 10080
only the details of the stress block are expressed). This is the Specifying EUROCODE 1 Reinforcing
traditional European approach, where the application of a Eurocode concrete Actions on steels
structures
is expected to be provided in a textbook or similar publication.
The Eurocodes allow for this type of detail to be provided in
‘Non-contradictory complementary information’ (NCCI) (See BS 8500 BS 4449
BS EN 1992
Specifying Reinforcing
Glossary). concrete
EUROCODE 2
steels
Design of concrete
4. Units for stress are mega pascals, MPa (1 MPa = 1 N/mm2). structures
5. Eurocode 2 uses a comma for a decimal point. It is expected that Part 1–1: General
rules for structures
UK designers will continue to use a decimal point. Therefore to
BS EN 13670 BS EN 13369
Part 1–2: Structural
avoid confusion, the comma should not be used for separating Execution of
fire design
Precast
structures concrete
multiples of a thousand.
6. One thousandth is represented by ‰.
-. Eurocode 2 is applicable for ribbed reinforcement with characteristic
BS EN 1992 BS EN 1992 Part 3: Precast
yield strengths of400 to 600 MPa.There is no guidance on plain EUROCODE 2 EUROCODE 2 concrete
bar or mild steel reinforcement in the Eurocode,but guidance is Part 2: Liquid-retaining product
Bridges structures standards
given in the background paper to the UK National Annex.
.. The effects of geometric imperfection (‘notional horizontal loads’)
are considered in addition to lateral loads.

/. Minimum concrete cover is related to bond strength,durability

and fire resistance.In addition to the minimum cover an
allowance for deviations due to variations in execution
(construction) should be included.Eurocode 2 recommendsthat,
for concrete cast against formwork,this is taken as 10 mm,
unless the construction is subject to a quality assurance system
in which case it could be reduced to 5 mm or even 0 mm where
non-conforming members are rejected (e.g.in a precast yard).It
is recommended that the nominal cover is stated on the
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

drawings and construction tolerances are given in the

5
specification.
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

1&. Ab`almk^g`ma\hg\k^m^bl covered by Eurocode 2,up toclass

C90/105.However,because the characteristics of higherstrength Eurocode 7
concrete are different,some Expressions in the Eurocodeare
Eurocode 7:Geotechnical design1;is in two parts and gives guidance on
adjusted for classes above C50/60.
geotechnical design,ground investigation and testing.It has a broad
1'. The ‘variable strut inclination’method is used in Eurocode 2 for scope and includes the geotechnical design of spread foundations,piled
the assessment of the shear capacity of a section.In practice, foundations,retaining walls,deep basements and embankments.Like
design values for actual structures can be compared with all the Eurocodes it is based on limit state design principles,which is
tabulatedvalues.Further advice can be found in Chapter 4. asignificant variation for most geotechnical design.Further guidance
related to simple foundations is given in Chapter 6.
Part1–2
Eurocode 2,Part 1–2:Structural fire design,gives guidance on design
forfire resistance of concrete structures.Although much of the
Eurocode is devoted to fireengineering methods,the design for fire Eurocode 8
resistancemaystill be carried out by referring to tables for minimum
cover anddimensions for various elements.These are given in section Eurocode 8:Design of structures for earthquake resistance1;is divided into
5 of Part1–2.Further advice on using the tabular method is given in six parts and gives guidance on all aspects of design for earthquake
Chapter 2. resistance and covers guidance for the various structural materials for
all types of structures.It also includes guidance for strengthening and
Part2 repair of buildings.In areas of low seismicity it is anticipated that detailing
Eurocode 2,Part 2:Bridges;applies the general rules given in Part 1–1 structures to Eurocode 2 will ensure compliance with Eurocode 8.
to the design of concrete bridges.As a consequence both Part 1–1 and
Part 2 will be required to carry out a design of a reinforced concrete
bridge. Related Standards
Part3 BS 8500/BS EN 206
Eurocode 2,Part3:Liquid-retaining and containmentstructures;applies BS 8500:Concrete – Complementary British Standard to BS EN 206–1.
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

the general rules given in Part 1–1 to the liquid-retaining structures. Further guidance can found inChapter +.

BS 4449/BS EN 10080
BS 4449:Specification for carbon steel bars for the reinforcement of
concrete;is a complementary standard to BS EN 10080 Steel for the
reinforcement of concrete;and Normative Annex C of Eurocode 2.
Mabl]^_bg^lma^lm^^elmk^g`mabgma^NDZl.))FIZ'Ma^k^Zk^ three
classes of reinforcement,A,B and C,whichindicate increasing ductility.
Class A is not suitable for use whereredistribution fhk^maZg+)aZl
been assumed in the design.

BS EN 13670
;L>G*,/0)3>q^\nmbhgh_\hg\k^m^lmkn\mnk^l*.aZlmak^^_ng\mbhgl3
■ MhmkZgl_^k]^lb`gk^jnbk^f^gmlmhma^\hgmkZ\mhk'
■ Mh`bo^lmZg]Zk]m^\agb\Zek^jnbk^f^gml_hkma^^q^\nmbhgiaZl^'
■ MhZb]ma^]^lb`g^kmh^glnk^Zeema^m^\agb\Zebg_hkfZmbhgblli^\b_b^]'

6
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
1. Introduction to Eurocodes

Glossary of Eurocode terminology

Term Definition
Principles Clauses that are general statements, definitions, requirements and analytical models for which no
alternative is permitted. They are identified by (P) after the clause number.
Application Rules These are generally recognised rules, which comply with the principles and satisfy their requirements.
Nationally Determined Parameter (NDP) Eurocodes may be used to satisfy national Building Regulations, which themselves will not be
harmonized. NDPs are therefore used to allow a country to set its own levels of safety. NDPs also allow
certain other parameters (generally influenced by climate, geography and geology) to be left open for
selection nationally: NDPs are advised in the National Annex.
National Annex (NA) A National Annex accompanies each Eurocode and it contains a) the values of NDPs b) the national
decision regarding the use of Informative Annexes c) references to NCCIsZg]]"gZmbhgZe]^\blbhg
pa^k^m^qmZeehplZem^kgZmbo^l'

Normative The term used for the text of Standards that forms the core requirements. Compliance with Eurocodes
will generally be judged against the normative requirements.
Informative A term used only in relation to annexes, which seek to inform rather than require.
NCCI Non-contradictory complementary information. References in a National Annex which contains further
information or guidance which does not contradict the Eurocode.
Characteristic value A value that may be derived statistically with a probability of not being exceeded during a reference
period. The value corresponds to a specified fractile for a particular property of material or product. The
characteristic values are denoted by subscript ‘k’ (e.g. Qk etc). It is the principal representative value
from which other representative values may be derived.
Representative value Value used for verification of a limit state. It may be the characteristic value or an accompanying value,
e.g. combination, frequent or quasi-permanent.
Design values These refer to representative values modified by partial factors. They are denoted by subscript ‘d’
(e.g. f cd ck/gsc; ; QQ
yd = fyk g QQQ
d d==gQ k) k).

Action (F) Set of forces, deformations or accelerations acting on the structure.

Combination of actions Set of design values used for the verification of the structural reliability for a limit state under the
simultaneous influence of different and statistically independent actions.
Fixed action Action that has a fixed distribution and position over the structure or structural member.
Free action Action that may have various spatial distributions over the structure.
Permanent actions (G) Actions that are likely to act throughout the life of the structure and whose variation in magnitude
with time is negligible (e.g. permanent loads).
Variable actions (Q) Actions whose magnitude will vary with time (e.g. wind loads).
Effect of action (E) Deformation or internal force caused by an action.
Accidental action (A) Action, usually of short duration but of significant magnitude, that is unlikely to occur on a given
structure during the design working life.
Accompanying action An action in a combination that is not the leading variable action.
Transient design situation Design situation that is relevant during a period much shorter than the design working life of the structure.
Persistent design situation Design situation that is relevant during a period of the same order as the design working life of the structure.
Accidental design situation Design situation involving exceptional conditions of the structure.
Irreversible serviceability limit state Serviceability limit state where some consequences of actions will remain when the actions are removed.
Reversible serviceability limit state Serviceability limit state where no consequences of actions will remain when the actions are removed.
Execution Construction of the works.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
7
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
1. Introduction to Eurocodes

References
1 BRITISH STANDARDS INSTITUTION. BS EN 1992, Eurocode 2: Design of concrete structures. BSI (4 parts).
2 BRITISH STANDARDS INSTITUTION. BS EN 1990, Eurocode: Basis of structural design. BSI, 2002.
3 BRITISH STANDARDS INSTITUTION. BS EN 1991, Eurocode 1: Actions on structures. BSI (10 parts).
4 GULVANESSIAN, H, CALGARO, J A & HOLICÝ, M T. Designers’ guide to EN 1990. Thomas Telford, 2002.
5 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–1, Eurocode 2: Design of concrete structures. General rules and rules for buildings. BSI, 2004.
6 BRITISH STANDARDS INSTITUTION. PD 6687-1. Background paper to the National Annexes to BS EN 1992-1 and BS EN 1992-3. BSI, 2010.
7 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–2, Eurocode 2: Design of concrete structures. Structural fire design. BSI, 2004.
8 BRITISH STANDARDS INSTITUTION. BS EN 1992–2, Eurocode 2: Design of concrete structures. Bridges. BSI, 2005.
9 BRITISH STANDARDS INSTITUTION. BS EN 1992–3, Eurocode 2: Design of concrete structures. Liquid-retaining and containment structures. BSI, 2006.
10 BRITISH STANDARDS INSTITUTION. BS EN 1997, Eurocode 7: Geotechnical design. BSI (2 parts).
11 BRITISH STANDARDS INSTITUTION. BS EN 1998, Eurocode 8: Design of structures for earthquake resistance. BSI (6 parts).
12 BRITISH STANDARDS INSTITUTION. BS 8500: Concrete – Complementary British Standard to BS EN 206–1, 2015 (2 parts).
13 BRITISH STANDARDS INSTITUTION. BS 4449: Specification for carbon steel bars for the reinforcement of concrete. BSI, 2005.
14 BRITISH STANDARDS INSTITUTION. BS EN 10080: Steel for the reinforcement of concrete – Weldable reinforcing steel – General. BSI, 2005.
15 BRITISH STANDARDS INSTITUTION. BS EN 13670: Execution of concrete structures – Part 1: Common. BSI, 2010.

8
Copyright The Concrete Centre
--`,``,,```,,`

Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas

No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2
2. Getting started
O Brooker BEng, CEng, MICE, MIStructE, MCS T A Harrison BSc, PhD, CEng, MICE, FICT J Burridge MA CEng MIStructE MICE

The design process

This chapter is intended to assist the designer determine all the design
information required prior to embarking on detailed element design. It
covers design life, actions on structures, load arrangements, combinations
of actions, method of analysis, material properties, stability and
imperfections, minimum concrete cover and maximum crack widths.

Design life
The design life for a structure is given in Eurocode: Basis of structural
design 1. The UK National Annex (NA) to Eurocode presents UK values for
design life; these are given in Table 1 (overleaf). These should be used to
determine the durability requirements for the design of reinforced
concrete structures.

Actions on structures
Eurocode 1: Actions on structures2 consists of 10 parts giving details of a
wide variety of actions. Further information on the individual codes can
be found in Chapter 1. Eurocode 1, Part 1–1: General actions –
Densities, self-weight, imposed loads for buildings3 gives the densities and
self-weights of building materials (see Table 2 overleaf).

h
o
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

Table 1
Indicative design working life (from UK National Annex to Eurocode) Load arrangements
Design life (years) Examples
10 Temporary structures The term load arrangements refers to the arranging of variable actions
10–30 Replaceable structural parts (e.g. imposed and wind loads) to give the most onerous forces in a
15–25 Agricultural and similar structures member or structure and are given in Eurocode 2 and its UK NA.
50 Buildings and other common structures
120 Monumental buildings, bridges and other civil For building structures, the UK NA to Eurocode 2, Part 1–1 allows any
engineering structures
of the following sets of load arrangements to be used for both the
ultimate limit state and serviceability limit state:
Table 2
Selected bulk density of materials (from Eurocode 1, Part 1–1) Load set 1. Alternate or adjacent spans loaded
Material Bulk density (kN/m3) The design values should be obtained from the more critical of:
Normal weight concrete 24.0 ■ Alternate spans carrying the design variable and permanent loads
Reinforced normal weight concrete 25.0 with other spans loaded with only the design permanent load (see
Wet normal weight reinforced concrete 26.0 Figure 1). The value of gG should be the same throughout.
■ Any two adjacent spans carrying the design variable and
permanent loads with other spans loaded with only the design
Figure 1
permanent load (see Figure 2). The value of gG should be the
Alternate spans loaded
same throughout.

Load set 2. All or alternate spans loaded

The design values should be obtained from the more critical of:
■ All spans carrying the design variable and permanent loads
(see Figure 3).
■ Alternate spans carrying the design variable and permanent loads
with other spans loaded with only the design permanent load (see
Figure 1). The value of gG should be the same throughout.

Generally, load set 2 will be used for beams and slabs in the UK as it
Figure 2 requires three load arrangements to be considered, while load set 1
Adjacent spans loaded
will often require more than three arrangements to be assessed.
Alternatively, the UK NA makes the following provision for slabs.

Load set 3. Simplified arrangements for slabs

The load arrangements can be simplified for slabs where it is only
necessary to consider the all spans loaded arrangement (see Figure 3),
provided the following conditions are met:
■ In a one-way spanning slab the area of each bay exceeds 30 m2
(a bay means a strip across the full width of a structure bounded
on the other sides by lines of support).
■ The ratio of the variable actions (Qk) to the permanent actions (Gk)
does not exceed 1.25.
■ The magnitude of the variable actions excluding partitions does not
exceed 5 kN/m2.

Figure 3
All spans loaded

10 --`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

Combination of actions be specified according to BS 8500: Concrete –

complementary British Standard to BS EN 206–1 (e.g. for class C28/35
The term combination of actions refers to the value of actions to be concrete the cylinder strength is 28 MPa, whereas the cube strength
used when a limit state is under the influence of different actions. is 35 MPa). Typical concrete properties are given in Table 4.

The numerical values of the partial factors for the ULS combination can
be obtained by referring to Eurocode: Basis of structural design or to Concrete up to class C90/105 can be designed using Eurocode 2.
Chapter 1. For classes above C50/60, however, there are additional rules and
variations. For this reason, the design of these higher classes is not
considered in this publication.
For members supporting one variable action the ULS combination
.( 1.25 Gk + 1.5 Qk (derived from Exp. (6.10b), Eurocode)
can be used provided the permanent actions are not greater than Reinforcing steel
4.5 times the variable actions (except for storage loads). Eurocode 2 can be used with reinforcement of characteristic
strengths ranging from 400 to 600 MPa. The properties of steel
There are three SLS combinations of actions – characteristic, frequent reinforcement in the UK for use with Eurocode 2 are given in
and quasi-permanent. The numerical values are given in Eurocode: Basis BS 4449 (2005): Specification for carbon steel bars for the
of structural design. reinforcement of concrete and are summarised in Table 5
(on page 12). A characteristic yield strength of 500 MPa has
been adopted by the UK reinforcement industry.
Material properties
There are three classes of reinforcement, A, B and C, which provide
Concrete increasing ductility. Class A is not suitable where redistribution of
In Eurocode 2 the design of reinforced concrete is based on the more than 20% has been assumed in the design. There is no
characteristic cylinder strength provision for the use of plain bar or mild steel reinforcement, but
guidance is given in the background paper to the National Annex6.
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Table 3
Selected imposed loads for buildings (from UK National Annex to Eurocode 1, Part 1–1)

Category Example use qk (kN/m2) Qk (kN)

A1 All uses within self-contained dwelling units 1.5 2.0
A2 Bedrooms and dormitories 1.5 2.0
A3 Bedrooms in hotels and motels, hospital wards and toilets 2.0 2.0
A5 Balconies in single family dwelling units 2.5 2.0
A7 Balconies in hotels and motels 4.0 min. 2.0 at outer edge
B1 Offices for general use 2.5 2.7
C5 Assembly area without fixed seating, concert halls, bars, places of worship 5.0 3.6
D1/2 Shopping areas 4.0 3.6
E12 General storage 2.4 per m height 7.0
E17 Dense mobile stacking in warehouses 4.8 per m height (min. 15.0) 7.0
F Gross vehicle weight ≤ 30kN 2.5 10.0

Table 4
Selected concrete properties based on Table 3.1 of Eurocode 2, Part 1–1

Symbol Description Properties

fck (MPa) Characteristic cylinder strength 12 16 20 25 30 35 40 45 50 28a 32a
fck,cube (MPa) Characteristic cube strength 15 20 25 30 37 45 50 55 60 35 40
fcm (MPa) Mean cylinder strength 20 24 28 33 38 43 48 53 58 36 40
fctm (MPa) Mean tensile strength 1.6 1.9 2.2 2.6 2.9 3.2 3.5 3.8 4.1 2.8 3.0
Ecm (GPa)
b
Secant modulus of elasticity 27 29 30 31 33 34 35 36 37 32 34
Key
a Concrete class not cited in Table 3.1, Eurocode 2, Part 1–1
b Mean secant modulus of elasticity at 28 days for concrete with quartzite aggregates. For concretes with other aggregates refer to Cl 3.1.3 (2)

11
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Table 5 Regardless of the method of analysis used, the following principles apply:
Characteristic tensile properties of reinforcement
Where a beam or slab is monolithic with its supports, the critical
Class (BS 4449) and designation (BS 8666) A B C design hogging moment may be taken as that at the face of the
Characteristic yield strength fyk or f 0.2k (MPa) 500 500 500 support, but should not be taken as less than 0.65 times the full
Minimum value of k = ( ft / fy ) k ≥ 1.05 ≥ 1.08 ≥ 1.15 < 1.35 fixed end moment.
Characteristic strain at maximum force e uk (%) ≥ 2.5 ≥ 5.0 ≥ 7.5 Where a beam or slab is continuous over a support that may be
Notes considered not to provide rotational restraint, the moment
1 Table derived from BS EN 1992–1–1 Annex C, BS 4449: 2005 and BS EN 100807 . calculated at the centre line of the support may be reduced by
2 The nomenclature used in BS 4449: 2005 differs from that used in BS EN 1992–1–1
Annex C and used here. (FEd,sup t/8), where FEd,sup is the support reaction and t is the breadth
3 In accordance with BS 8666, class H may be speciﬁed,
be specified, in which
in which case case
classclass
A, B A,
or BC or C
may be supplied when bar diameter ≤ 12 mm, otherwise
otherwiseclasses
classesBBororCCmust
mustbebe supplied.
supplied. of the support.
For the design of columns the elastic moments from the frame
action should be used without any redistribution.
Table 6
Bending moment and shear co-efficients for beams Bending moment and shear force co-efficients for beams are given in
Moment Shear Table 6; these are suitable where spans are of similar length and the
Outer support 25% of span moment 0.45 (Gd++ Q)d)
0.45 (G other notes to the table are observed.
Near middle of end span Gd +l +0.100
0.090 Gl Qd l
0.100Ql
At first interior support G d++QQ) dl )l
– 0.094 ((G 0.63 (Gd++Q
0.63 (G Q)da)a
At middle of interior spans Gd+l +0.086
0.066 Gl 0.086QlQd l Minimum concrete cover
At interior supports (Gd++QQ)dl)l
–– 0.075 (G 0.50 (Gd++Q
0.50 (G Q)d)
Key The nominal cover can be assessed as follows:
a 0.55 (Gd ++ Q)
0.55 (G Qd)may
maybe
beused
usedadjacent
adjacentto
tothe
theinterior
interiorspan.
span
Notes
cnom = cmin + D cdev Exp. (4.1)
1 Redistribution of support moments by 15% has been included.
2 Applicable to 3 or more spans only and where Qk ≤ G k. Where cmin should be set to satisfy the requirements below:
3 Minimum span ≥ 0.85 longest span.
4 l is the span, Gd islength,
effective G is the
the design value of permanent
total of the ULS actions (at ULS)
permanent andQQis
actions, d is thetotal
the design safe transmission of bond forces
of theofULS
value variable
variable actions.
actions (at ULS). fire resistance
durability
and D cdev is an allowance which should be made in the design for
Structural analysis deviations from the minimum cover. It should be taken as 10 mm,
unless fabrication (i.e. construction) is subjected to a quality assurance
The primary purpose of structural analysis in building structures is to system, in which case it is permitted to reduce D cdev to 5 mm.
establish the distribution of internal forces and moments over the
whole or part of a structure and to identify the critical design Figure 4
conditions at all sections. The geometry is commonly idealised by Sections through structural members, showing nominal axis distance, a

considering the structure to be made up of linear elements and plane

two-dimensional elements.

The type of analysis should be appropriate to the problem being

considered. The following may be used: linear elastic analysis, linear
elastic analysis with limited redistribution, and plastic analysis. Linear
elastic analysis may be carried out assuming cross sections are
uncracked (i.e. concrete section properties); using linear stress-strain
relationships, and assuming mean values of elastic modulus.

For the ultimate limit state only, the moments derived from elastic Minimum cover for bond
analysis may be redistributed (up to a maximum of 30%) provided The minimum cover to ensure adequate bond should not be less than
that the resulting distribution of moments remains in equilibrium with the bar diameter, or equivalent bar diameter for bundled bars, unless
the applied loads and subject to certain limits and design criteria (e.g. the aggregate size is over 32 mm.
limitations of depth to neutral axis).

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

12
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
2. Getting started

Design for fire resistance Durability

Eurocode 2 Part 1–2:Structural fire design,gives several methods BS ntary British Standard to BS EN 206-14
for determining the fire resistance of concrete elements.Design for
fire resistance may still be carried out by referring to mZ[e^l%Zg]
]^mZbe^]`nb]Zg\^hg_bk^k^lblmZg\^_hkiZkmb\neZkê^f^gmmri^lZk^
`bo^gbgma^kêôZgm\aZim^kl'Pa^k^mZ[neZkf^mah]lZk^ghm
lZmbl_Z\mhkr%<aZim^k**ikhob]^lfhk^`nb]Zg\^hgma^nl^h_
Exposure classification
lbfieb_b^]\Ze\neZmbhgf^mah]l'
Initially the relevant exposure condition(s) should be identified.
In BS 8500 exposure classification is related to the deterioration
Rather than giving the minimum cover,the tabular method is based
processes of carbonation, ingress of chlorides, chemical attack
on nominal axis distance,a(see Figure 4).This is the distance from the
from aggressive ground and freeze/thaw (see Table 7). All of these
centre of the main reinforcing bar to the surface of the member.It is a
deterioration processes are sub-divided. The recommendations for
nominal (not minimum) dimension.The designer should ensure that
XD and XS exposure classes are sufficient for exposure class XC
cnom+flink +ffZbg[ar /2ªZfbg%pa^k^Zfbgblma^fbgbfnfZqbl
and it is only necessary to check each face of the concrete
]blmZg\^_khfma^_bk^mZ[e^l'
element for either XC, XD or XS exposure class.

There are three standard fire exposure conditions that may be satisfied:
R Mechanical resistance for load bearing Selecting concrete strength and cover
E Integrity of separation Having identified the relevant exposure condition(s), a
I Insulation recommended strength class and cover should be chosen.
Table 8 indicates the minimum cover and strengths required to
The _bk^tables offer flexibilitr in that there are options available to the meet common exposure conditions for a 50-year working life;
designer e.g.sectionsizes can be reduced by increasing the axis further explanation is given below. Table 8 is not intended to
distance.Further informationis given in Eurocode 2 and subsequent cover all concrete exposure situations and reference should be
chapters,including designlimitations and data for walls and beams. made to BS 8500 for those cases not included, and where a
100-year working life is required.

Compressive strength
BS 8500 uses ‘compressive strength class’ to define concrete
strengths; the notation used gives the cylinder strength as well as
the cube strength (see Tables 9(a) and 9(b). It is important to
quote the compressive strength class in full to avoid confusion.

Cover to reinforcement
The durability guidance given in BS 8500 is based on the
assumption that the minimum cover for durability is achieved.
An allowance should be made in the design for deviations from
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
the minimum cover (Dcdev). This should be added to the
minimum cover to obtain the nominal cover.

13
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Table -
Exposure Classes

Class Class description Informative example applicable to the United Kingdom

No risk of corrosion or attack (XO class)
X0 For concrete without reinforcement or Unreinforced concrete surfaces inside structures. Unreinforced concrete completely buried in soil
embedded metal where there is no significant classed as AC-1 and with hydraulic gradiant not greater than 5. Unreinforced concrete permanently
freeze/thaw, abrasion or chemical attack. submerged in non-aggressive water. Unreinforced concrete in cyclic wet and dry conditions not
subject to abrasion, freezing or chemical attack.
NOTE: ?hkk^bg_hk\^]\hg\k^m^% nl^Zme^ZlmQ<*'

Corrosion induced by carbonation (XC classes) a

(Where concrete containing reinforcement or other embedded metal is exposed to air and moisture.)

XC1 Dry or permanently wet. Reinforced and prestressed concrete surfaces inside enclosed structures except areas of structures
with high humidity. Reinforced and prestressed concrete surfaces permanently submerged in
non-aggressive water.
XC2 Wet, rarely dry. Reinforced and prestressed concrete completely buried in soil classed as AC-1 and with a hydraulic
gradient not greater than 5' For other situations see ‘chemical attack’ section below.
XC3 & Moderate humidity or cyclic wet and dry. External reinforced and prestressed concrete surfaces sheltered from, or exposed to, direct rain.
XC4 Reinforced and prestressed concrete surfaces inside structures with high humidity (e.g. poorly
ventilated, bathrooms, kitchens). Reinforced and prestressed concrete surfaces exposed to alternate
wetting and drying.

Corrosion induced by chlorides other than from sea water (XD classes) a
(Where concrete containing reinforcement or other embedded metal is subject to contact with water containing chlorides, including de-icing salts,
from sources other than from sea water.)

XD1 Moderate humidity. Concrete surfaces exposed to airborne chlorides. Parts of structures exposed to occasional or slight
chloride conditions.
XD2 Wet, rarely dry. Reinforced and prestressed concrete surfaces totally immersed in water containing chlorides b.
XD3 Cyclic wet and dry. Reinforced and prestressed concrete surfaces directly affected by de-icing salts or spray containing
de-icing salts (e.g. walls; abutments and columns within 10 m of the carriageway; parapet edge
beams and buried structures less than 1 m below carriageway level, pavements and car park slabs).

Corrosion induced by chlorides from sea water (XS classes) a

(Where concrete containing reinforcement or other embedded metal is subject to contact with chlorides from sea water or air carrying salt originating from sea water.)

XS1 Exposed to airborne salt but not in direct External reinforced and prestressed concrete surfaces in coastal areas.
contact with sea water.
XS2 Permanently submerged. Reinforced and prestressed concrete completely submerged and remaining saturated,
e.g. concrete below mid-tide level b.
XS3 Tidal, splash and spray zones. Reinforced and prestressed concrete surfaces in the upper tidal zones and the splash and
spray zones c.
Freeze/thaw attack (XF classes)
(Where concrete is exposed to significant attack from freeze/thaw cycles whilst wet.)

XF1 Moderate water saturation without Vertical concrete surfaces such as facades and columns exposed to rain and freezing. Non-vertical
de-icing agent. concrete surfaces not highly saturated, but exposed to freezing and to rain or water.
XF2 Moderate water saturation with de-icing agent. Elements such as parts of bridges, which would otherwise be classified as XF1 but which are
exposed to de-icing salts either directly or as spray or run-off.
XF3 High water saturation without de-icing agent. Horizontal concrete surfaces, such as parts of buildings, where water accumulates and which are
exposed to freezing. Elements subjected to frequent splashing with water and exposed to freezing.
XF4 High water saturation with de-icing agent Horizontal concrete surfaces, such as roads and pavements, exposed to freezing and to de-icing
or sea water d. salts either directly or as spray or run-off. Elements subjected to frequent splashing with water
containing de-icing agents and exposed to freezing.
Chemical attack (ACEC classes)
(Where concrete is exposed to chemical attack.) Note: BS 8500-1 refers to ACEC classes rather than XA classes used in BS EN 206-1

Key
a The moisture condition relates to that in the concrete cover to reinforcement or other embedded develop a specification that is appropriate to the actual conditions likely to be encountered.
metal but, in many cases, conditions in the concrete cover can be taken as being that of the
c Exposure XS3 covers a range of conditions. The most extreme conditions are in the spray zone. The
surrounding environment. This might not be the case if there is a barrier between the concrete and
least extreme is in the tidal zone where conditions can be similar to those in XS2. The
its environment.
recommendations given take into account the most extreme UK conditions within this class.
b Reinforced and prestressed concrete elements, where one surface is immersed in water containing
d It is not normally necessary to classify in the XF4 exposure class those parts of structures located in
chlorides and another is exposed to air, are potentially a more severe condition, especially where the
the United Kingdom which are in frequent contact with the sea.
dry side is at a high ambient temperature. Specialist advice should be sought where necessary, to

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

2
14
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
2. Getting started

Table .
Selected a recommendations for normal-weight reinforced concrete quality for combined exposure classes and cover to reinforcement for at least a
50-year intended working life and 20 mm maximum aggregate size

Exposure conditions Cement/ Strength classc, maximum w/c ratio, minimum cement or combination
combination content (kg/m3), and equivalent designated concrete (where applicable)
designationsb
Typical example Primary Secondary Nominal cover to reinforcementd
15 + D c dev 20 + D c dev 25 + D c dev 30 + D c dev 35 + D c dev 40 + D c dev 45 + D c dev 50 + D c dev
Internal mass
X0 ___ All Recommended that this exposure is not applied to reinforced concrete
concrete
Internal elements C20/25,
(except humid XC1 ___ All 0.70, 240 or <<< <<< <<< <<< <<< <<< <<<
locations) RC20/25

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
Buried concrete C25/30,
in AC-1 ground XC2 AC-1 All ___ ___ 0.65, 260 or <<< <<< <<< <<< <<<
conditions e RC25/30
Vertical surface C40/50, C3+/-), C28/35, C25/30,
protected from ___ All except ___ 0.45, 340 or 0.55,300hk 0.60, 280 or 0.65, 260 or <<< <<< <<<
IVB-V
direct rainfall RC40/50 RC30/37 RC28/35 RC25/30
C40/50, C3+/-), C28/35,
Exposed vertical
XF1
All except ___ 0.45, 340 or 0.55,300hk 0.60, 280 or <<< <<< <<< <<<
surfaces IVB-V
XC3 RC40/50 RC3+/-) RC28/35
& C40/50,0.45,
XC4 XF3
All except ___ 340 g or <<< <<< <<< <<< <<< <<<
IVB-V
RC40/50XFg
Exposed horizontal
surfaces C30/37, C28/35, C25/30,
XF3 (air All except ___ ___ 0.55, 300 0.60, 280 0.60, 280
<<< <<< <<<
entrained) IVB-V plus air g,h plus air g,h plus air g, h, j
or PAV2 or PAV1
Elements subject
to airborne XD1f ___ All ___ ___ C40/50, C32/40, C28/35,
<<< <<< <<<
0.45, 360 0.55, 320 0.60, 300
chlorides

IIB-V, IIIA ___ ___ ___ ___ ___ C35/45, C32/40, C28/35,
0.40, 380 0.45, 360 0.50, 340
Car park decks and
areas subject to ___ CEM I, IIA, ___ ___ ___ ___ ___ See C40/50, C35/45,
IIB-S BS 8500 0.40, 380 0.45, 360
de-icing spray
IIIB, IVB-V ___ ___ ___ ___ ___ C32/40, C28/35, C25/30,
0.40, 380 0.45, 360 0.50, 340

IIB-V, IIIA ___ ___ ___ ___ ___ C35/45, C32/40, C32/40,
0.40, 380 0.45, 360 0.50, 340
Vertical elements XD3f
subject to de-icing XF2
CEM I, IIA, ___ ___ ___ ___ ___ See C40/50, C35/45,
IIB-S BS 8500 0.40, 380 0.45, 360
spray and freezing
IIIB, IVB-V ___ ___ ___ ___ ___ C32/40, C32/40 C32/40,
0.40, 380 0.45, 360 0.50, 340

Car park decks, XF4

CEM I, IIA, ___ ___ ___ ___ ___ See C40/50,
<<<
ramps and external IIB-S BS 8500 0.40, 380 g
areas subject to
freezing and XF4 (air ___ ___ ___ ___ ___ C28/35, C28/35 C28/35,
IIB-V, IIIA, IIIB 0.40, 380g, h 0.45, 360g, h 0.50, 340g, h
de-icing salts entrained)

CEM I, IIA, _ _ ___ See <-)(.)%

IIB-S BS 8500 )'-)%,1)
XF1
Exposed vertical
IIB-V, IIIA ___ ___ ___ See C32/40, C28/35, C28/35,
<<<
surfaces near coast BS 8500 0.45, 360 0.50, 340 0.55, 320
XS1f
___ IIIB%BO&; ___ ___ ___ C32/40, C25/30, C25/30, C25/30,
<<<
0.40, 380 0.50, 340 0.50, 340 0.55, 320
Exposed horizontal XF3 or CEM I, IIA, ___ ___ ___ See C40/50,
surfaces near coast XF4 IIB-S BS 8500 0.4),,1)`
Key d D c dev is an allowance for deviations. ___ Not recommended
a This table comprises a selection of common exposure class combinations. e For sections less than 140 mm thick refer to BS 8500.
Requirements for other sets of exposure classes,e.g.XD2,XS2 and XS3 should f Also adequate for exposure class XC3/4. <<< Indicates that concrete
be derived from BS 8500-1:20*.,Annex A. g Freeze/thaw resisting aggregates should be specified. quality in cell to the left
b See BS 8500-2,Table 1.(CEM I is Portland cement,IIA to IVB are cement combinations.) h Air entrained concrete is required. should not be reduced
c For prestressed concrete the minimum strength class should be C28/35. j This option may not be suitable for areas subject to
severe abrasion.

3
15
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Table 9a
Eurocode 29 recommends that Dcdev is taken as 10 mm, unless the Compressive strength class for normal and heavyweight concrete
fabrication is subjected to a quality assurance system where it is
Example Compressive strength classes (BS 8500)
permitted to reduce Dcdev to 5 mm, or 0 mm if the element can be
rejected if it is out of tolerance (e.g. precast elements). C20/25
C25/30
Cement types and minimum cement content C28/35
Table 1) may be used to understand the cement/combination C30/37
designations. It should be noted from Table 1 that the strength,water/ C32/40
cement ratio and minimum cement content may vary depending on
C35/45
the cement type used. In the UK, all cement/combinations are
C40/50
available (except SRPC), although in most concrete production plants
either ground granulated blastfurnace slag (GGBS) or flyash (fa) is C45/55

available; not both.When using a designated concrete (see section C50/60

below), it is not necessary to specify the types of cement/combinations.

Table /b Table 1&

Explanation of the compressive strength class notation Cement and combination typea
Broad Composition Cement/combination
A Includes heavyweight concrete

C
‘C’ for normal
40 /50
Cylinder Cube
B Minimum characteristic 150 mm
diameter by 300 mm cylinder
designationb
CEM I Portland cement
types (BS 8500)
CEM I
strength, N/mm2
weight strengthB strengthC SRPC Sulfate-resisting Portland cement SRPC
concrete A C Minimum characteristic cube
‘LC’ for strength, N/mm2 IIA Portland cement with 6–20% of fly CEM II/A-L, CEM II/A-LL,
lightweight ash, ground granulated blastfurnace CIIA-L, CIIA-LL,
concrete slag, limestone, or 6–10% silica CEM II/A-S, CIIA-S
fumec CEM II/A-V, CIIA-V
CEM II/A–D
Air content
IIB-S Portland cement with 21–35% CEM II/B-S, CIIB-S
Where air entrainment is required for exposure classes XF3 and XF4
ground granulated blastfurnace slag
the minimum air content by volume of 3.0%,3.5% or 5.5% should
IIB-V Portland cement with 21–35% fly ash CEM II/B-V, CIIB-V
be specified for 40 mm,20 mm and 10 mm maximum aggregate size
respectively. IIB+SR Portland cement with 21–35% fly ash CEM II/B-V+SR,
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

CIIB-V+SR

Freeze/thaw aggregates IIIAd, e Portland cement with 36–65% CEM III/A,, CIIIA
ground granulated blastfurnace slag
For exposure conditions XF3 and XF4 freeze/thaw resisting
IIIA+SRe Portland cement with 36–65% CEM III/A+SRf,
aggregates should be specified.The producer is then obliged to
ground granulated blastfurnace slag CIII/A+SRf
conform to the requirements given in BS 8500–2:20*.,Cl.4.3. with additional requirements that
enhance sulfate resistance
Aggressive ground IIIBe, g Portland cement with 66–80% CEM III/B, CIIIB
Where plain or reinforced concrete is in contact with the ground ground granulated blastfurnace slag
further checks are required to ensure durability. An aggressive IIIB+SRe Portland cement with 66–80% CEM III/B+SRf , CIIIB+SRf
chemical environment for concrete class (ACEC class) should be ground granulated blastfurnace slag
with additional requirements that
assessed for the site. BRE Special Digest 110 gives guidance on the
enhance sulfate resistance
assessment of the ACEC class and this is normally carried out as part
IVB-V Portland cement with 36–55% fly ash CEM IV/B(V), CIVB
of the interpretive reporting for a ground investigation. Knowing the
Key
ACEC class, a design chemical class (DC class) can be obtained from a There are a number of cements and combinations not listed in this table that may be specified for
Table 1*. certain specialist applications. See BRE Special Digest 110. for the sulfate-resisting characteristics of other
cements and combinations.
b The use of these broad designations is sufficient for most applications.Where a more limited range of
cement or combinations types is required,select from the notations given in BS 8500-2:20*.,Table 1.
For designated concretes, an appropriate foundation concrete (FND c When IIA or IIA-D is specified,CEM I and silica fume may be combined in the concrete mixer using the
designation) can be selected using Table 1+; the cover should be k-value concept;see BS EN 206-1:20*,,5.2.5.2.3.
d Where IIIA is specified,IIIA+SR may be used.
determined from Table 1 for the applicable exposure classes. A FND e Inclusive oflow earlystrength option (see BS EN 197-4 and the “L”classes in BS8500-2:2006,Table A.1.).
f “+SR”indicates additional restrictions related to sulfate resistance.See BS 8500-2:2006,Table 1,
concrete has the strength class of C25/30, therefore, where a higher footnote D.
strength is required a designed concrete should be specified. For g WhereIIIB is specified,IIIB+SR maybe used.

designed concretes, the concrete producer should be advised of the

DC-class (see section on specification).

16
4
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
2. Getting started

Table ''
Selection of the DC-class and the number of Addition Protection 9edYh[j[_dYedjWYjm_j^j^[]hekdZ
Measures (APMs) where the hydrostatic head of groundwater is not more The lowest nominal cover is 25 + ͅc mm. The minimum allowance for
than five times the section width a,b, c, d , e
deviation,ͅc, should be at least 15 mm for concrete to be cast against
ACEC-class DC-class blinding or prepared ground and at least 50 mm for concrete to be cast
(Aggressive directly against soil, see BS 8500-1 note E to Table A.10.
Chemical Intended working life
Environment for At least 50 years At least 100 years
Concrete class) Abrasion
AC-1s, AC-1 DC-1 DC-1 BS 8500 does not contain abrasion classes;instead reference should be
made to BS 8204-2;orConcrete Society Technical Report 34.Table
AC-2s, AC-Z DC-2 DC-2
*,summarises the factors that affect the abrasion resistance of floors.
AC-2z DC-2z DC-2z

AC-3s

AC-3z
DC-3

DC-3z
DC-3

DC-3z
Specification
AC-3 DC-3 Refer to BS 8500 Method of specifying
AC-4s DC-4 DC-4 There are various methods of specifying concrete to BS 8500
(see Table *-).The most popular are designated and designed.
AC-4z DC-4z DC-4z
BS 8500 alsointroduces a new method ‘proprietary concrete’.
AC-4 DC-4 Refer to BS 8500

AC-4ms DC-4m DC4m

The specifier
Figures . and / show mrib\Zestandardspecification forms.Similar
AC-4m DC-4m Refer to BS 8500 tables are included in the National Structural ConcreteSpecification
AC-5 DC-4f DC-4f (NSCS).In BS 8500 the ‘specifier’is the person or bodyresponsible for
the final compilation of the technical requirements,called the
AC-5z DC-4zf DC-4z/1 f
specification,which is passed to the concrete producer.This will
AC-5m DC-4mf DC-4mf generally be the contractor,however,the designer will wantto ensure
Key their requirements are incorporated and this will normallybe through
a Where the hydrostatic head of groundwater is greater than five times the section width,refer to BS 8500.
their own specification for the works (e.g.with theNSCS).Figures .
b For guidance on precast products see Special Digest 1*).
and / have been annotated to indicate whichinformation is typically
c For structural performance outside these values refer to BS 8500.
provided by the designer and contractor.Thedesigner should require
d For section widths < 140 mm refer to BS 8500.
e Whereanysurface attackis not acceptable e.g.with friction piles,refer to BS 8500.
that any reported non-conformities arepassed to them for
f This should include APM3 (surface protection),where practicable,as one of the APMs;refer to BS 8500. assessment.

Table '(
Guidance on selecting designated concrete for reinforced concrete
Consistence
foundations The term ‘workability’has been replaced by the term ‘consistence’and a
series of consistence classes has been introduced.MZ[e^l*.ZZg]*.[
DC-Class Appropriate Designated Concrete
`bo^ theslump and flow classes and the likelytarget slump/flow.
DC-1 RC 25/30
DC-2 FND2 Chloride Class
DC-2z FND2z Concrete that is to be prestressed,pre-tensioned or heat curedlahne]
ghkfZeer[^li^\b_b^]Zl\aehkb]^\eZll<e)%*)'K^bg_hk\^]\hg\k^m^
DC-3 FND3 lahne][^li^\b_b^]Zl\eZll<e)%-)'Ihlm&m^glbhg^]^e^f^gmlbgZg
DC-3z FND3z bgm^kgZe[nbe]bg`^gobkhgf^gmfZrZelh[^li^\b_^]Zl\eZll<e)%*)'
DC-4 FND4
DC-4z FND4z
DC-4m FND4m

NOTE
Strength class for all FND concrete is C25/30.

<hgmbgn^liZ`^+)

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

5
17
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Table ')
Factors affecting the abrasion resistance of concrete floors

Factor Effect
Power floating Power finishing and, in particular, repeated power trowelling is a significant factor in creating abrasion
resistance, however, excessive repetitions of the process do not necessarily further enhance performance.
Curing Prompt and efficient curing is essential in order to retain sufficient water in the surface zone to complete
hydration and the development of concrete strength at and close to the surface.
Cement content Cement content should not be less than 325 kg/m3. Cement contents above 360 kg/m3 are unlikely to
enhance abrasion resistance and excessive cement content can impair the power finishing process.
Water/cement ratio Water/cement ratio is of great importance. It should not exceed 0.55. Reducing to 0.50 is likely to increase
abrasion resistance but lowering further is unlikely to give further enhancement.
Aggregates Coarse aggregate usually has no direct effect on abrasion resistance, except in floors in very aggressive
environments where the surface is expected to be worn away. Coarse and fine aggregates should not contain
soft or friable materials.
Dry shake finishes Dry shake finishes can be used to enhance the surface properties in high abrasion locations.

Figure +
Example specification of Designated Concrete
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Schedule for the specification requirements of designated concretes for use on contract
Contract Title: New Office
Contract period: June - Dec ‘04

BS 8500-1 reference Requirement Schedule

4.2.2a) The concretes below shall be supplied as Designated Concretes in accordance with
this specification and the relevant clauses of BS 8500-2A
4.2.2b) D Concrete designation FND2 z RC25/30 RC32/40 D
4.2.2c) Maximum aggregate size when other –– –– 10
D than 20 mm D
O

4.2.2d) Consistence S1, S2, S3, S4 S1, S2, S3, S4 S1, S2, S3, S4 S1, S2, S3, S4
(Ring the class required when other than F2, F3, F4, F5 F2, F3, F4, F5 F2, F3, F4, F5 F2, F3, F4, F5
the default classes of S3 for the GEN, FND
and RC series and S2 for the PAV series. Use
a separate column for different consistence
with the same designated concrete)
C Other (specify) C
4.2.3 C D Additional requirements –– –– –– C D
Exchange of information
3
BS EN 206-1, 7.1 Total volume required 48 m 12003 m3 72 m3 3
3
Anticipated peak delivery rate 6 m /day 18 m /hr 6 m /day
C Any access limitations C
KEY
5.1a) Intended method of placing, Skip + Pumping Skip + D Designer specifies
e.g. pumping, and finishing, e.g. power tamped + float tamped concrete designation,
C floating, the concrete C maximum aggregate
size and any
5.1b) Where identity testing is routine: N/A N/A N/A additional
Type of test requirements
Volume of concrete in assessment
Number of tests on this volume Contractor specifies
C
Whether a non-accredited laboratory consistence, any
additional
C will be used C
requirements and
5.1 & BS EN 206-1, 7.1 Other information from the specifier –– –– –– completes exchange
C to the producer C of information
section
5.2 & BS EN 206-1, 7.2 Information required from –– –– ––
C the producer C Red text
Example
A There is no need to cite BS EN 206-1 as BS 8500-2 has a clause that requires conformity to BS EN 206-1. specification

6
18
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
2. Getting started

Table '*
Methods of specifying concrete

BS 8500 BS 5328 (superseded by BS 8500 1 Dec 2003)

Designated concrete Designated mix
Designed concrete Designed mix
Prescribed concrete Prescribed mix
Standardized prescribed concrete Standard mix
Proprietary concrete No equivalent

Figure ,
Example specification of Designed Concrete

Schedule for the specification requirements of designed concretes for use on contract
Contract Title: New Office
Contract period: June - Dec ‘04

BS 8500-1 Requirement Schedule

reference
4.3.2a) The concretes below shall be supplied as designed concretes in accordance with this specification
and the relevant clauses of BS 8500-2A
D Concrete reference, if any Pads Slab Cols D
4.3.2b) D Compressive strength class C28/35 C25/30 C32/40 D
4.3.2c) For sulfate resisting concrete, design chemical class DC-2z DC- DC- DC-
D D
For other concretes, limiting values of composition: 0.70 0.55
Maximum w/c ratio
D Minimum cement/combination content, kg/m3 240 300 D
4.3.2d) & Cement or combination types CEM 1, SRPC, CEM 1, SRPC, CEM 1, SRPC, CEM 1, SRPC,
4.3.3a) (delete those not permitted) IIA, IIB IIA, IIB IIA, IIB IIA, IIB

D
Other special property, e.g. white, low heat, +SR
(specify)
IIIA, IIIB, IVB xx
IIIA, IIIB, IVB xx
IIIA, IIIB, IVB IIIA, IIIB, IVB
D
4.3.2e) D Maximum aggregate size, mm 20 20 10 D KEY
4.3.2f) Chloride class (ring the one required) Cl 0,10 Cl 0,10 Cl 0,10 Cl 0,10 D Designer specifies
O

Prestressed or heat cured reinforced concrete RC RC RC RC compressive strength

Reinforced B Cl 1,0 Cl 1,0 Cl 1,0 Cl 1,0 class, design chemical
D Unreinforced with no embedded metal D class, maximum
4.3.2g) & h) For lightweight and heavyweight concrete, water/cement ratio,
D target density D minimum cement
O

O
O

content, cement or
4.3.2i) Consistence (Ring the class required. S1, S2, S3, S4 S1, S2, S3, S4 S1, S2, S3, S4 S1, S2, S3, S4
Use separate columns for the same basic F2, F3, F4, F5 F2, F3, F4, F5 F2, F3, F4, F5 F2, F3, F4, F5 combination types
concretes with different consistence) (unless design
C D Other (specify) C D chemical class is
specified), maximum
4.3.2 UKAS or equivalent accredited third party product Yes Yes Yes Yes aggregate size,
Note 2 D conformity certification (delete if not required) D
chloride class, target
4.3.3b) Additional requirements density (excluding
to n) C D C D normal weight
Exchange of information concrete),
3 requirement for
BS EN Volume required 48 m 1200 m3 72 m3 third party product
206-1, 7.1
C
Anticipated peak delivery rate 6 m3/day 18 m3/hr 6 m3/day C conformity
Any access limitations
certification
5.1a) Intended method of placing, e.g. pumping, and Skip + Pumping Skip + (recommended)
C finishing, e.g. power floating, the concrete tamped + float tamped C and any additional
5.1b) Where identity testing is routine: requirements
Type of test
N/A N/A N/A
Volume of concrete in assessment C Contractor specifies
consistence,
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Number of tests on this volume

C Whether a non-accredited laboratory will be used C any additional
requirements and
5.1 & BS EN Other information from the specifier to the –– –– –– completes exchange
206-1,7.1 C producer C
of information
5.2 & BS EN Information required from the producer –– –– –– section
206-1, 7.2 C C
A There is no need to cite BS EN 206-1 as BS 8500-2 has a clause that requires conformity to BS EN 206-1.
Red text
Example
B Where RC is ringed, the chloride class shall be Cl 0.40 except where SRPC is used. In this case the chloride class shall be Cl 0,20. Specification

7
19
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

JWXb['+W Conformity
Consistence slump classes and likely target values
Under BS 8500,the concrete producer is required to follow aformal
Slump class Target slump (mm) procedure called ‘conformity’to verify that the concrete is in
S1 20 accordance with the specification.It is,therefore,recommended
S2 70
that the concrete supplier should have third party certification.
Where this is not adopted,the specifier is advised to adopt
S3 130
adequate identity testing to ensure the concrete is as specified.
S4 190
Identity testing
The specifier is responsible for organising any identity testing, which
TWXb['+X is in all but in name acceptance testing. Identity testing can include
Consistence flow classes and likely target values strength, consistence and air content. There are a number of
situations where it is recommended:
Flow class Target flow (mm)
■ where the producer does not hold third party certification
F2 380
■ in cases of doubt
F3 450 ■ for critical elements, e.g. high strength columns
F4 520 ■ for spot checks on the producer.

F5 590
Exchange of information
To enable the concrete producer to design and produce a suitable
concrete, certain information must be provided in addition to the
specification, e.g. where the concrete needs to be pumped or a high
quality finish is required.

Special requirements
Where particular requirements are important, e.g. visual concrete or
sustainability, further guidance can be found in The Concrete Centre
publications, Specifying Sustainable Concrete and Visual Concrete.
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

20
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
2. Getting started

Stability and imperfections Crack control

The effects of geometric imperfections should be considered in Crack widths should be limited to ensure appearance and durability
combination with the effects of wind loads (i.e. not as an alternative are satisfactory.In the absence of specific durability requirements
load combination). For global analysis, the imperfections may be (e.g.water tightness) the crack widths may be limited to 0.3 mm in
represented by an inclination y i . all exposure classes under the quasi-permanent combination.In the
absence of requirements for appearance,this limit may be relaxed
y i = (1/200) x a h x a m (tosay 0.4 mm) for exposure classes X0 and XC1 (refer to Table 7).
where Thetheoretical size of the crack can be calculated using the
a h = (2/Rl), to be taken as not less than 2/3 nor greater than 1.0 expressionsgiven in Cl 7.3.4 from >nkh\h]^+%iZkm*&* or from the
a m = [0.5 (1 + 1/m)]0.5 ‘deemed to satisfy’requirements that can be obtained from Table 1/,
l is the height of the building in metres which is based ontables 7.2N and 7.3N h_>nkh\h]^+IZkm*&*2.
m is the number of vertical members contributing to the horizontal The limits apply to either thebar size or the bar spacing,not both.
force in the bracing system.
Figure -
The effect of the inclination may be represented by transverse forces at Examples of the effect of geometric imperfections
each level and included in the analysis along with other actions (see
Figure 0):

Effect on bracing system: Hi = y i (Nb – Na)

Effect on floor diaphragm: Hi = y i (Nb + Na)/2
Effect on roof diaphragm: Hi = y i Na
where Na and Nb are longitudinal forces contributing to Hi.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
In most cases,an allowance for imperfections is made in the partial
factors used in the design of elements.However for columns,the effect a) Bracing system b) Floor diaphragm c) Roof diaphragm
of imperfections,which is similar in principle to the above,must be
considered (see Chapter 5).
Figure .
Determination of steel stress for crack width control

Table 1,
Maximum bar size or spacing to limit crack width
Approximate steel stress at SLS for As, req, ssu

Steel wmax = 0.4 mm wmax = 0.3 mm

stress
Maximum Maximum Maximum Maximum
(s s)MPa bar bar bar bar
size (mm) spacing (mm) size (mm) spacing (mm)

160 40 300 32 300

200 32 OR 300 25 OR 250
240 20 250 16 200
280 16 200 12 150
320 12 150 10 100
360 10 100 8 50
Note
The steel stress may be estimated from the expression below (or see Figure 1):
ss = fyk m As,req
gs n As,prov d
where
fyk = characteristic reinforcement yield stress
gs = partial factor for reinforcing steel
m = total load from quasi-permanent combination
n = total load from ULS combination To determine stress in the reinforcement (ss), calculate the ratio Gk/Qk,
As,req = area of reinforcement at the ULS read up the graph to the appropriate curve and read across to determine ssu .
As,prov = area of reinforcement provided As,req 1
ss can be calculated from the expression: ss = ssu
d = ratio of redistributed moment to elastic moment
As,prov d ( )( )

21
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
2. Getting started

References
1 BRITISH STANDARDS INSTITUTION. BS EN 1990, Eurocode: Basis of structural design. BSI, 2002.
2 BRITISH STANDARDS INSTITUTION. BS EN 1991, Eurocode 1: Actions on structures. BSI (10 parts).
3 BRITISH STANDARDS INSTITUTION. BS EN 1991, Eurocode 1: Actions on structures Part 1–1: General actions – Densities, self-weight, imposed loads
for buildings. BSI, 2002.
4 BRITISH STANDARDS INSTITUTION. BS 8500–1: Concrete – Complementary British Standard to BS EN 206–1– Part 1: Method of specifying and
guidance for the specifier. BSI, 2015.
5 BRITISH STANDARDS INSTITUTION. BS 4449: Specification for carbon steel bars for the reinforcement of concrete. BSI, 2005.
6 BRITISH STANDARDS INSTITUTION. PD6687-1: Background paper to the National Annexes to BS EN 1992-1 and BS EN 1992-3. BSI, 2010.
7 BRITISH STANDARDS INSTITUTION. BS EN 10080: Steel for the reinforcement of concrete – Weldable reinforcing steel – General. BSI, 2005.
8 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–2, Eurocode 2: Design of concrete structures. General rules – structural fire design. BSI, 2004.
9 BRITISH STANDARDS INSTITUTION. BS EN 1992-1-1, Eurocode 2: Design of concrete structures. General rules and rules for buildings. BSI, 2004.
10 BUILDING RESEARCH ESTABLISHMENT. Special Digest 1: Concrete in aggressive ground. BRE, 2005.
11 BRITISH STANDARDS INSTITUTION, BS 8204-2: Screeds, bases and in-situ floorings, Part 2: Concrete and wearing surfaces - Code of Practice, BSI, 2003.
12 BRITISH STANDARDS INSTITUTION. BS EN 206–1: Concrete – Part: Specification, performance, production and conformity. BSI, 2013.
13 THE CONCRETE SOCIETY, Technical Report 34: Concrete Industrial Ground Floors, The Concrete Society, 2013.
14 CONSTRUCT, National Structural Concrete Specification for Building Construction, Construct, 2010.
15 GOODCHILD, CH; WEBSTER, R.M; ELLIOTT, K.S, Economic Concrete Frame Elements to Eurocode 2, The Concrete Centre, 2009.
16 NARAYANAN, RS; GOODCHILD, CH, Concise Eurocode 2, The Concrete Centre, 2006.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
17 GOODCHILD, CH; MORRISON, J & VOLUM, RL, Strut-and-Tie Models, The Concrete Centre, 2014.
18 GOODCHILD, CH, Worked Examples to Eurocode 2: Volume 1, The Concrete Centre, 2009.

Further Guidance
There are a number of useful publications giving further guidance on the use of Eurocode 2, particularly for areas not covered by the scope of this
publication, including:
Q Economic Concrete Frame Elements15, which provides quick reference guidance on the size of concrete elements for buildings.
Q Concise Eurocode 216, which provides the key Eurocode 2 clauses in one document with embedded UK NDPs for ease of reference.
Q Strut-and-Tie Models17, giving best practice guidance on the strut-and-tie clauses in Eurocode 2.
Q Worked Examples to Eurocode 2: Volume 118.

22
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2
3. Slabs
R M MossBSc,PhD,DIC,CEng,MICE,MIStructE O BrookerBEng,CEng,MICE,MIStructE%F<L J Burridge MA CEng MIStructE MICE

Designing to Eurocode 2
Mabl\aZim^k\ho^klma^ZgZerlblZg]]^lb`gh_\hg\k^m^leZ[lmh>nkh\h]^+*'
>nkhi^ZgikZ\mb\^blmh`boîkbg\bie^lZg]`^g^kZeZiieb\Zmbhgkne^lbgma^\h]^lZg]
_hk]^mZbe^]Ziieb\Zmbhgkne^lmh[îk^l^gm^]bghma^klhnk\^lln\aZlm^qm[hhdlhk
`nb]Zg\^]h\nf^gml'>nkh\h]^+]h^lghm\hgmZbgZeema^_hkfneZ^maZmZk^g^^]^]
mh]^lb`gleZ[lZg]ma^l^_hkfneZâZo^mh[^]^kbo^]'^'`'>nkh\h]^+]h^lghm
\hgmZbgZ_hkfneZmh\Ze\neZm^ma^Zk^Zh_k^bg_hk\^f^gm%:l%mhk^lblmZgZiieb^]
nembfZm^[^g]bg`fhf^gm%F'=^kbo^]_hkfneZ^mh]^lb`gleZ[lZk^`bo^gbgmabl
\aZim^k'<aZim^k0\ho^klma^]^lb`gh__eZmleZ[l'

Design procedure
A procedure for carrying out the detailed design of slabs is shown in Table 1.This
assumes that the slab thickness has previously been determined duringconceptual
design.More detailed advice on determining design life,actions,material properties,
methods of analysis,minimum concrete cover fordurability and control of crack
widths can be found in Chapter 2.

Fire resistance
Eurocode 2,Part 1–2:Structural fire design,gives a choice of advanced,simplified
or tabular methods fordetermining the fire resistance.Using tablesis the fastest
method for determining the minimum dimensions and cover forslabs.There are,
however,some restrictions which should be adhered to.Further guidance on
simplified methods bl`bo^gbg<aZim^k**'

KZma^kmaZg`bobg`Zfbgbfnf\ho^k%ma^mZ[neZkf^mah]bl[Zl^]hgghfbgZeZqbl
]blmZg\^%Z'Mablblma^]blmZg\^_khfma^\^gmk^h_ma^fZbgk^bg_hk\bg`[Zkmhma^
lnk_Z\^h_ma^f^f[^k'Pa^k^ma^k^Zk^Zgnf[^kh_[Zklikhob]bg`k^lblmZg\^bm\Zg
[^\hglb]^k^]mh[^ZghfbgZe!ghmfbgbfnf"]bf^glbhg%lhma^]^lb`g^klahne]
^glnk^maZm\ghf$∅e bgd$∅fZbg[Zk(+ªZfbg%pa^k^Zfbgblma^fbgbfnfZqbl]blmZg\^
_khfma^_bk^mZ[e^l'Ma^k^jnbk^f^gml_hkoZkbhnlmri^lh_leZ[Zk^`bo^gbgMZ[e^+'

Flexure
The design procedure for flexural design is given in Figure 1;thisincludes derived
formulae based on the simplified rectangular stressblock from Eurocode 2<e','*'0!,"%
!l^^?b`nk^+".Where appropriate,Table 3 may be used todetermine bending
moments and shear forces for slabs.Furtherinformation for the design of two-way,
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

ribbed or waffle slabs is given inthe appropriate sections on pages +0 and +1.

Copyright The Concrete Centre

Table 1
Slab design procedure

Step Task Further guidance

Chapter in this publication Standard
1 Determine design life 2: Getting started NA to BS EN 1990 Table NA.2.1
2 Assess actions on the slab 2: Getting started BS EN 1991 (10 parts) and National Annexes
3 Determine which combinations of actions apply 1: Introduction to Eurocodes NA to BS EN 1990 Tables NA.A1.1 and NA.A1.2 (B)
4 Determine loading arrangements 2: Getting started NA to BS EN 1992–1–1
5 Assess durability requirements and determine concrete strength 2: Getting started BS 8500:20*.
6 Check cover requirements for appropriate fire resistance period 2: Getting started and Table 2 Approved Document B. BS EN 1992–1–2: Section 5
7 Calculate min. cover for durability, fire and bond requirements 2: Getting started BS EN 1992–1–1 Cl 4.4.1
8 Analyse structure to obtain critical moments and shear forces 2: Getting started and Table 3 BS EN 1992–1–1 section 5
9 Design flexural reinforcement See Figure 1 BS EN 1992–1–1 section 6.1
10 Check deflection See Figure 3 BS EN 1992–1–1 section 7.4
11 Check shear capacity See Table 7 BS EN 1992–1–1 section 6.2
12 Check spacing of bars 2: Getting started BS EN 1992–1–1 section 7.3
Note
NA = National Annex.

Table 2
Minimum dimensions and axis distances for reinforced concrete slabs (excluding flat slabs)

Standard fire Minimum dimensions (mm)

resistance
One-way a,b Two-way spanning slaba,b,c,d Ribs in a two-way spanning ribbed slabe
spanning slab l y /l x ≤ 1.5 f 1.5 <l y /l x ≤ 2f

REI 60 hs = 80 80 80 b min = 100 120 ≥200

a= 20 10 g 15g a= 25 15g 10g
REI 90 hs = 100 100 100 b min = 120 160 ≥250
a= 30 15g 20 a= 35 25 15g
REI 120 hs = 120 120 120 b min = 160 190 ≥300
a= 40 20 25 a= 45 40 30
REI 240 hs = 175 175 175 b min = 450 700
–––
a= 65 40 50 a= 70 60

Notes Key
1 This table is taken from BS EN 1992–1–2 Tables 5.8 to 5.11. For flat slabs refer to a The slab thickness hs is the sum of the slab thickness and the thickness of any
Chapter 7. non-combustible flooring.
2 The table is valid only if the detailing requirements (see note 3) are observed and in b For continuous solid slabs a minimum negative reinforcement As ≥ 0.005 A c
normal temperature design redistribution of bending moments does not exceed 15%. should be provided over intermediate supports if
3 For fire resistance of R90 and above, for a distance of 0.3l eff from the centre line of each 1) cold worked reinforcement is used; or
intermediate support, the area of top reinforcement should not be less than the following: 2) there is no fixity over the end supports in a two span slab; or
A s,req (x) = A s,req ( 0 ) ( 1 – 2.5 ( x/ l eff ) ) 3) where transverse redistribution of load effects cannot be achieved.
where: c In two way slabs the axis refers to the lower layer of reinforcement.
x is the distance of the section being considered from the centre
d The term two way slabs relates to slabs supported at all four edges. If this is
line of the support.
not the case, they should be treated as one-way spanning slabs.
A s,req ( 0 ) is the area of reinforcement required for normal temperature design.
e For two-way ribbed slabs the following notes apply:
A s,req (x) is the minimum area of reinforcement required at the section
The axis distance measured to the lateral surface of the rib should be at
being considered but not less than that required for normal
least (a + 10).
temperature design.
The values apply where there is predominantly uniformly distributed loading.
l eff is the greater of the effective lengths of the two adjacent spans.
There should be at least one restrained edge.
4 There are three standard fire exposure conditions that need to be satisfied:
The top reinforcement should be placed in the upper half of the flange.
R Mechanical resistance for load bearing
E Integrity of separation f l x and l y are the spans of a two-way slab (two directions at right angles) where
I Insulation l y is the longer span.

5 The ribs in a one-way spanning ribbed slab can be treated as beams and reference can g Normally the requirements of BS EN 1992–1–1 will determine the cover.
be made to Chapter 4, Beams. The topping can be treated as a two-way slab where
1.5 < ly / lx ≤ 2.

2
24 --`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

Figure 1
Procedure for determining flexural reinforcement

D aZl[^^g]^m^kfbg^]nlbg`NDGZmbhgZe:gg^qoZen^lbg>nkh\h]^
START
IZkm*&*>qi!.'*)'Z"'Ma^D oZen^blkêZm^]mhma^fZqbfnfoZen^h_
q(]pab\ablZeehp^][r>qi!.'*)Z"mh^glnk^ln__b\b^gmkhmZmbhgh_ma^
Carry out analysis of slab to determine design moments (M)
(Where appropriate use coefficients from Table 3)
l^\mbhg\ZgmZdîeZ\^'Mh^glnk^maZmma^k^bg_hk\^f^gmaZlrbê]^]bm
blh_m^gk^\hff^g]^]bgma^NDmaZmma^fZqbfnfoZen^h_D lahne]
[êbfbm^]mh)'*/1pab\a\hkk^lihg]lmhZfZqbfnfq(]h_)'-.'Mabl
No blghmZk^jnbk^f^gmh_>nkh\h]^+%[nmbl\hglb]^k^]mh[^`hh]
Concrete class Outside scope of
≤C50/60? this publication ikZ\mb\^'
Ma^fhk^ma^êZlmb\[^g]bg`fhf^gmlZk^k^]n\^][rk^]blmkb[nmbhgma^
Yes
lfZee^kmaôZen^h_q(]aZlmh[^%l^^MZ[e^-'Pa^gq(]bl)'/ma^lm^ê
M lmkZbgbl)'))+,,Zg]ma^k^bg_hk\^f^gmaZliZll^]bmlrbê]lmkZbgh_
Determine K from: K =
bd 2 fck
)'))+*06_r](>l'

Determine K’ from Table 4 or Table*

Table 4
K’ = 0.60d – 0.18 d 2 – 0.21 where d ≤ 1.0 Values for K’
LWbk[i\ehA½

%
% redistribution
redistribution dd(redistribution
(redistributionratio) K’
ratio) K’ x/d
Compression 00 1.00
1.00 0.208aa
0.208 0.6
No reinforcement
10 0.90
0.90 0.182aa
0.182 0.5
Is K ≤ K ’ ? required – not
recommended for 15 0.85
0.85 0.168
0.168 0.45
typical slabs
20 0.80
0.80 0.153
0.153 0.4
Yes 25 0.75 0.137 0.35
0.75 0.137
30
30 0.70
0.70 0.120
0.120 0.3
No compression reinforcement required
Key
Key
a It
a It is
is often
often recofmended
recommended in
in the
the UK
UK that K´should
that K’ shouldbe
belimited
limitedto
to0.168
0.*/1to
toensure
ensureductile
ductilefailure.
failure.
Obtain lever arm z from Table 5 or
d Table 5
z=
2 [
1 + 1 – 3.53 K ≤ 0.95d ] z/d for singly reinforced rectangular sections

K z/d K z/d
Calculate tension reinforcement required from ≤0.05 0.950a 0.13 0.868
M
As = 0.06 0.944 0.14 0.856
fyd z
0.07 0.934 0.15 0.843
0.08 0.924 0.16 0.830
Check minimum reinforcement requirements (see Table 6) 0.09 0.913 0.17 0.816
0.26 fctm bt d 0.10 0.902 0.18 0.802
As,min = where fck ≥ 25
fyk 0.11 0.891 0.19 0.787
0.12 0.880 0.20 0.771
Key
Check maximum reinforcement requirements
a Limiting z to 0.95d is not a requirement of Eurocode 2, but is considered to be good practice.
As,max = 0.04 Ac for tension or compression
reinforcement outside lap locations

Table 6
Minimum percentage of reinforcement required
Table 3
Bending moment and shear coefficients for slabs fck fctm Minimum % (0.26 fctm /fyka )
25 2.6 0.13%
End support /slab connection First Interior Interior
interior spans supports 28 2.8 0.14%
Pinned Continuous
support 30 2.9 0.15%
End End End End
support span support span 32 3.0 0.16%
Moment 0 0.086Fl – 0.04Fl 0.075Fl –0.086Fl 0.063Fl –0.063Fl 35 3.2 0.17%
Shear 0.40F 0.46F 0.6F 0.5F 40 3.5 0.18%
Notes 45 3.8 0.20%
1 Applicable to one-way spanning slabs where the area of each bay exceeds 30 m2,
Qk ≤ 1.25 Gk and qk ≤ 5 kN/m2 50 4.1 0.21%
2 F is the total design ultimate load, l is the span Key
3 Minimum span > 0.85 longest span, minimum 3 spans
4 Based on 20% redistribution at supports and no decrease in span moments a Where fyk = 500 MPa.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

3
25
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

The Eurocode gives recommendations for the design of concrete up to

class C90/105. However, for concrete greater than class C50/60, the stress
Deflection
block is modified. It is important to note that concrete strength is based
Eurocode 2 has two alternative methods of designing for deflection,
on the cylinder strength and not the cube strength (i.e. for class C28/35
either by limiting span-to-depth ratio or by assessing the theoretical
the cylinder strength is 28 MPa, whereas the cube strength is 35 MPa).
deflection using the Expressions given in the Eurocode. The latter is
dealt with in detail in Chapter 8.

The span-to-depth ratios should ensure that deflection is limited to

span /250 and this is the procedure presented in Figure 3. It should be
noted that the UK National Annex recommends that Mlis calculated
using characteristic values and not quasi-permanent values.
Figure 2
Simplified rectangular stress block for concrete up to class C50/60 from Eurocode 2

Figure 3 Figure 4
Procedure for assessing deflection Determination of approximate steel stress at SLS

START

Determine basic l/d_dYbkZ_d]Afrom Figure 5

Determine Factor 1 (F1)

For ribbed or waffle slabs
F1 = 1 – 0.1 ((bf/bw) – 1) ≥ 0.8†
(bf is flange breadth and bw is rib breadth)
Otherwise F1 = 1.0

Determine Factor 2 (F2)

Where the slab span exceeds 7 m and it supports
brittle partitions,F2 = 7/leff
Otherwise F2 = 1.0

Determine Factor 3 (F3)

F3 = As,prov/As,req ≤ 1.5 or 310/ss ≤ 1.5 (UK NA)
where ss is the stress in the reinforcement calculated
under the characteristic combination of SLS loads. ξ
I[[\_]kh[* Increase
As,prov To determine stress in the reinforcement (σs), calculate the ratio Gk/Qk,
read up the graph to the appropriate curve and read across to determine
σsu. σs can be calculated from the expression: σs = σsu (As,req/As,prov) ( 1/δ)
Is basic l/d x F1 x F2 x F3 ≥ Actual l/d ?
No

Yes
Check complete

†The Eurocode is ambiguous regarding linear interpolation.It is understood that this

was the intention of the drafting committee and is in line with current UK practice.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

26
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
3. Slabs

Design for shear Table 7

vRd,c resistance of members without shear reinforcement, MPa

It is not usual for a slab to contain shear reinforcement,therefore it is rI = Effective depth, d (mm)
As /(bd)
only necessary to ensure that the concrete shear stress capacity ≤200 225 250 275 300 350 400 450 500 600 750
without shear reinforcement (vRd,c – see Table 7) is more thanma^
0.25% 0.54 0.52 0.50 0.48 0.47 0.45 0.43 0.41 0.40 0.38 0.36
appliedshear stress (vEd = VEd/(bd)).Where shear reinforcement is
required,e.g.for ribs in a ribbed slab,refer to Chapter 4. 0.50% 0.59 0.57 0.56 0.55 0.54 0.52 0.51 0.49 0.48 0.47 0.45

0.75% 0.68 0.66 0.64 0.63 0.62 0.59 0.58 0.56 0.55 0.53 0.51

1.00% 0.75 0.72 0.71 0.69 0.68 0.65 0.64 0.62 0.61 0.59 0.57

Two-way slabs 1.25% 0.80 0.78 0.76 0.74 0.73 0.71 0.69 0.67 0.66 0.63 0.61

1.50% 0.85 0.83 0.81 0.79 0.78 0.75 0.73 0.71 0.70 0.67 0.65
Mhere is no specific guidance given in Eurocode 2 onhow to
determine the bending moments for a two-way slab.Theassessment 1.75% 0.90 0.87 0.85 0.83 0.82 0.79 0.77 0.75 0.73 0.71 0.68
of the bending moment can be carried out using anysuitable method ≥2.00% 0.94 0.91 0.89 0.87 0.85 0.82 0.80 0.78 0.77 0.74 0.71
from Section 5 of the Code.However,co-efficientsmay be obtained
from Table 8 (taken from the Manual for the design ofbuilding k 2.000 1.943 1.894 1.853 1.816 1.756 1.707 1.667 1.632 1.577 1.516

structures to Eurocode 2) to determine bending moments perunit Table derived from: v Rd,c = 0.12 k (100r I fck)1/3 ≥ 0.035 k1.5 fck 0.5
width (Msx and Msy ) where: where k = 1 + R(200/d) ≤ 2 and r I = As /(bd) ≤ 0.02
Note
Msx = bsxw lx2 1 This table has been prepared for fck = 30.
2 Where r I exceeds 0.40% the following factors may be used:
Msy = b sy w lx2
fck 25 28 32 35 40 45 50
Where bsx and bsy are coefficients,lx is the shorter span and w(load
Factor 0.94 0.98 1.02 1.05 1.10 1.14 1.19
per unit area) is the STR ultimate limit state combination.For more
information on combinations refer to Chapter 1.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
Figure 5
Basic span-to-effective-depth ratios

Notes
1 For two-way spanning slabs, the check should be
carried out on the basis of the shorter span.
2 This graph assumes simply supported span
condition (K = 1.0).
K = 1.5 for interior span condition
K = 1.3 for end span condition
K = 0.4 for cantilevers
3 Compression reinforcement, r’, has been taken as 0.
4 Curves based on the following expressions:

1.5
1.5 fck r 0 r0
l
d [
= K 11 +
r
+ 3.2 fck
( )]
r
–1

where r ≤ r 0

and

1.5 fck r 0 fck r’

l
d
= K 11 +[ ( r – r ’)
+
12 r0 ]
where r > r 0 .

Percentage of tension reinforcement (As,req/bd)

5
27
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Ribbed or waffle slabs Figure 6

Procedure for determining flexural capacity of flanged ribs

Current practices for determining forces in ribbed and waffle slabs may also
START
be used for designs to Eurocode 2. Where a waffle slab is treated as a
two-way slab refer to previous section,but note that their torsional stiffness
is significantly less than for a two-way slab and the bending moment co-
efficients may not be applicable.Where it is treated as a flat slab reference No Outside scope
Concrete class of this
may be made to Chapter 7 ≤ C50/60? publication

The position of the neutral axis in the rib should be determined,and Yes

then the area of reinforcement can be calculated depending on Determine l0 (see Figure 7) and beff from:
whether it lies in the flange or web (see flow chart in Figure 6). beff = (bw + beff1 + beff2) where
beff1 = (0.2b1 + 0.1 l0) ≤ 0.2 l0 ≤ b1
beff2 = (0.2b2 + 0.1 l0) ≤ 0.2 l0 ≤ b2
Pa^k^ZleZ[bl_hkf^]pbmai^kfZg^gm[eh\dlhkZpbmaZmhiibg` Note: The flange width at the support will be
mab\dg^lle^llmaZg.)ffZg]hg^&m^gmah_ma^\e^Zk]blmZg\^ different from that at mid-span.
For symbols refer to Figures 7 and 8
[^mp^^gkb[lbmblk^\hff^g]^]maZmZehg`bmn]bgZela^Zk\a^\dbl
\Zkkb^]hnmmh]^m^kfbg^pa^ma^kZ]]bmbhgZemkZglo^kl^k^bg_hk\^f^gm
blk^jnbk^]!l^^;L>G*22+¾*¾*%<e/'+'-"'
M
Determine K from: K =
bd 2 fck

Table 8 Determine K’from Table * or

Bending moment coefficients for two-way spanning rectangular slabs
K’= 0.60d– 0.18 d2 – 0.21 where d≤ 1.0
supported by beams

Type or panel Short span coefficients for Long-span

and moments values of ly /lx coefficients
Calculate lever arm z from
considered for all values d
of ly /lx z=
2 [ 1 + 1 – 3.53 K ≤ 0.95d ]
1.0 1.25 1.5 1.75 2.0

Interior panels Calculate depth to neutral axis x from:

x = 2.5 (d – z)
Negative moment 0.031 0.044 0.053 0.059 0.063 0.032
at continuous edge
Neutral axis in
Positive moment 0.024 0.034 0.040 0.044 0.048 0.024 Yes flange.
at midspan Is x ≤ 1.25hf Design as
rectangular
section.
One short edge discontinuous
No
Negative moment 0.039 0.050 0.058 0.063 0.067 0.037
at continuous edge Neutral axis in web
Calculate moment capacity of flange from:
Positive moment 0.029 0.038 0.043 0.047 0.050 0.028 MR,f = 0.57 fck (beff – bw) hf (d – 0.5hf)
at midspan
M – MR,f
and Kf =
One long edge discontinuous fck bw d 2

Negative moment 0.039 0.059 0.073 0.083 0.089 0.037

at continuous edge
No
Is Kf ≤ K ’ Redesign
Positive moment 0.030 0.045 0.055 0.062 0.067 0.028 section
at midspan

Two adjacent edges discontinuous Yes

Negative moment 0.047 0.066 0.078 0.087 0.093 0.045 Calculate area of reinforcement required from
at continuous edge MR,f M – MR,f
As = +
fywd (d – 0.5 hf ) fywd z
Positive moment 0.036 0.049 0.059 0.065 0.070 0.034
at midspan

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

28
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
3. Slabs

Figure 7 Figure 8
Definition of l0 , for calculation of effective flange width Effective flange width parameters

Selected symbols
Rules for spacing and Symbol Definition Value

quantity of reinforcement Ac
As
Cross sectional area of concrete
Area of tension steel
bh

As2 Area of compression steel

Minimum area of principal reinforcement As, prov Area of tension steel provided
The minimum area of principal reinforcement in the main direction is As, req Area of tension steel required
As,min = 0.26 fc tm b t d/fy k but not less than 0.0013b td, where b t is the beff Effective flange width
mean width of the tension zone (see Table 6). For a T-beam with the bt Mean width of the tension zone
flange in compression, only the width of the web is taken into account bmin Width of beam or rib
in calculating the value of b t. bw Width of rib web

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
d Effective depth
Minimum area of secondary reinforcement d2 Effective depth to compression reinforcement
The minimum area of secondary transverse reinforcement is
fcd Design value of concrete compressive strength acc fck /gc
20% As,min . In areas near supports, transverse reinforcement is not
fck Characteristic cylinder strength of concrete
necessary where there is no transverse bending moment.
fctm Mean value of axial tensile strength 0.30 fck2/3 for fck ≤ C50/60
(from Table 3.1, Eurocode 2)
Maximum area of reinforcement hf Flange thickness
Outside lap locations, the maximum area of tension or compression hs Slab thickness
reinforcement should not exceed As,max = 0.04 Ac K Factor to take account of the different See Table NA.. in
structural systems UK National Annex

Minimum spacing of reinforcement leff Effective span of member See Section 5.3.2.2 (1)

The minimum clear distance between bars should be the greater of: l0 Distance between points of zero moment

■ Bar diameter l/d Limiting span-to-depth ratio

■ Aggregate size plus 5 mm lx, ly Spans of a two-way slab

■ 20 mm M Design moment at the ULS
x Depth to neutral axis (d – z)/0.4
Maximum spacing of reinforcement xmax Limiting value for depth to neutral axis (d – 0.4)d where d ≤1.0
For slabs less than 200 mm thick the following maximum spacing z Lever arm
rules apply: a cc Coefficient taking account of long term 0.85 for flexure and
effects on compressive strength and of axial loads.
■ For the principal reinforcement: 3h but not more than 400 mm
unfavourable effects resulting from the 1.0 for other phenomena
■ For the secondary reinforcement: 3.5h but not more than 450 mm way load is applied (From UK National Annex)
d Ratio of the redistributed moment to the
The exception is in areas with concentrated loads or areas of maximum elastic bending moment

moment where the following applies: gm Partial factor for material properties 1.15 for reinforcement (gs )
1.5 for concrete (gc )
■ For the principal reinforcement: 2h but not more than 250 mm
r0 Reference reinforcement ratio *)&,Rfck
■ For the secondary reinforcement: 3h but not more than 400 mm
r Required tension reinforcement at mid-span As/bd
Where h is the depth of the slab.
to resist the moment due to the design
loads (or at support for cantilevers)
For slabs 200 mm thick or greater the bar size and spacing should be r’ Required compression reinforcement at As2/bd
limited to control the crack width and reference should be made to mid-span to resist the moment due to the
design loads (or at support for cantilevers)
section 7.3.3 of the Code or Chapter 2,Gettingstarted.

29
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
3. Slabs

References
1 BRITISH STANDARDS INSTITUTION.BS EN 1992–1–1:Eurocode 2:Design of concrete structures – Part 1–1 General rules and rules for buildings.BSI,2004.
( BRITISH STANDARDS INSTITUTION.BS EN 1992–1–2,Eurocode 2:Design of concrete structures.General rules – structural fire design,BSI 2004.
) THE INSTITUTION OF STRUCTURAL ENGINEERS/THE INSTITUTION OF CIVIL ENGINEERS.Manual for the design of concrete building structures to
>nkh\h]^+'BLmkn\m>(B<>%+))/'
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

30
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

4. Beams
R Moss BSc, PhD, DIC, CEng, MICE, MIStructE O Brooker BEng, CEng, MICE, MIStructE J Burridge MA CEng MIStructE MICE

Designing to Eurocode 2
Mabl\aZim^k\ho^klma^ZgZerlblZg]]^lb`gh_\hg\k^m^[^Zflmh>nkh\h]^+*'
>nkhi^ZgikZ\mb\^blmh`boîkbg\bie^lZg]`^g^kZeZiieb\Zmbhgkne^lbgma^
\h]^lZg]_hk]^mZbe^]Ziieb\Zmbhgkne^lmh[îk^l^gm^]bghma^klhnk\^lln\a
Zlm^qm[hhdlhk`nb]Zg\^]h\nf^gml'>nkh\h]^+]h^lghm\hgmZbgZeema^
_hkfneZ^maZmZk^g^^]^]mh]^lb`g[^ZflZg]ma^l^_hkfneZâZo^mh[^
]^kbo^]^'`'>nkh\h]^+]h^lghm\hgmZbgZ_hkfneZmh\Ze\neZm^ma^Zk^Zh_
k^bg_hk\^f^gm%:l%mhk^lblmZgZiieb^]nembfZm^[^g]bg`fhf^gm%F'=^kbo^]
_hkfneZ^mh]^lb`g[^ZflZk^`bo^gbgmabl\aZim^k'

Bmlahne][^ghm^]maZmoZen^l_khfma^NDGZmbhgZe:gg^q!G:"aZo^[^^g
nl^]makhnàhnm%bg\en]bgòZen^lmaZmZk^^f[^]]^]bg]^kbo^]_hkfneZ^
!]^kboZmbhgl\Zg[^_hng]Zmppp'\hg\k^m^\^gmk^'\hf(^nkh\h]^+"':eblmh_
lrf[helkêZm^]mh[^Zf]^lb`gbl`bo^gZmma^^g]h_mabl\aZim^k'

Design procedure
:ikh\^]nk^_hk\Zkkrbg`hnmma^]^mZbe^]]^lb`gh_[^ZflbllahpgbgMZ[e^*'
MablZllnf^lmaZmma^[^Zf]bf^glbhglaZoîkôbhnler[^^g]^m^kfbg^]
]nkbg`\hg\îmnZe]^lb`g'Fhk^]^mZbe^]Z]ob\^hg]^m^kfbgbg`]^lb`geb_^%
Z\mbhgl%fZm^kbZeikhi^kmb^l%f^mah]lh_ZgZerlbl%fbgbfnf\hg\k^m^\ho^k_hk
]nkZ[bebmrZg]\hgmkheh_\kZ\dpb]mal\Zg[^_hng]bg<aZim^k+'

Fire resistance
>nkh\h]^+%IZkm*¾+3Lmkn\mnkZe_bk^]^lb`g+%`bo^lZ\ahb\^h_Z]oZg\^]%
lbfieb_b^]hkmZ[neZkf^mah]l_hk]^m^kfbgbg`ma^_bk^k^lblmZg\^'Nlbg`mZ[e^l
blma^_Zlm^lmf^mah]_hk]^m^kfbgbg`ma^fbgbfnf]bf^glbhglZg]\ho^k
_hk[^Zfl'Ma^k^Zk^%ahp^o^k%lhf^k^lmkb\mbhglZg]b_ma^l^Ziier_nkma^k
`nb]Zg\^hglbfieb_b^]f^mah]lbl`bo^gbg<aZim^k**'KZma^kmaZg`bobg`Z
fbgbfnf\ho^k%ma^mZ[neZkf^mah]bl[Zl^]hgghfbgZeZqbl]blmZg\^%Z!l^^
?b`nk^*"'Mablblma^]blmZg\^_khfma^\^gmk^h_ma^fZbgk^bg_hk\bg`[Zkmh
ma^mhihk[hmmhflnk_Z\^h_ma^f^f[^k'
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

JWXb[ '
8[Wc Z[i_]d fheY[Zkh[

Ij[f JWia <khj^[h ]k_ZWdY[

Chapter in this publication Standard
* =^m^kfbg^]^lb`geb_^ +3@^mmbg`lmZkm^] G:mh;L>G*22)MZ[e^G:'+'*
+ :ll^llZ\mbhglhgma^[^Zf +3@^mmbg`lmZkm^] ;L>G*22*!*)iZkml"Zg]GZmbhgZe:gg^q^l
, =^m^kfbg^pab\a\hf[bgZmbhglh_Z\mbhglZiier *3Bgmkh]n\mbhgmh>nkh\h]^l G:mh;L>G*22)MZ[e^lG:':*'*Zg]G:':*'+!;"
- =^m^kfbg^ehZ]bg`ZkkZg`^f^gml +3@^mmbg`lmZkm^] G:mh;L>G*22+¾*¾*
. :ll^ll]nkZ[bebmrk^jnbk^f^gmlZg]]^m^kfbg^\hg\k^m^lmk^g`ma +3@^mmbg`lmZkm^] ;L1.))3+)*.
/ <a^\d\ho^kk^jnbk^f^gml_hkZiikhikbZm^_bk^k^lblmZg\^i^kbh] +3@^mmbg`lmZkm^] Zg]Â?bk^k^lblmZg\^Ã :iikho^]=h\nf^gm;' ;L>G*22+¾*¾*3 L^\mbhg.
l^\mbhg
0 <Ze\neZm^fbg' \ho^k_hk]nkZ[bebmr% _bk^Zg][hg]k^jnbk^f^gml +3@^mmbg`lmZkm^] ;L>G*22+¾*¾*<e-'-'*
1 :gZerl^lmkn\mnk^mhh[mZbg\kbmb\Zefhf^gmlZg]la^Zk_hk\^l +3@^mmbg`lmZkm^] Zg]MZ[e^, ;L>G*22+¾*¾*l^\mbhg.
2 =^lb`g_e^qnkZek^bg_hk\^f^gm L^^Â?e^qnk^Ã l^\mbhg ;L>G*22+¾*¾*l^\mbhg/'*
*) <a^\dla^Zk\ZiZ\bmr L^^ÂO^kmb\Zela^ZkÃ l^\mbhg ;L>G*22+¾*¾*l^\mbhg/'+
** <a^\d]^_e^\mbhg L^^Â=^_e^\mbhgÃ l^\mbhg ;L>G*22+¾*¾*l^\mbhg0'-
*+ <a^\dliZ\bg`h_[Zkl +3@^mmbg`lmZkm^] ;L>G*22+¾*¾*l^\mbhg0',
Dej[
G:6GZmbhgZe:gg^q

JWXb[(
C_d_ckcZ_c[di_ediWdZWn_iZ_ijWdY[i\ehX[WcicWZ[m_j^h[_d\ehY[ZYedYh[j[\eh\_h[h[i_ijWdY[
IjWdZWhZ\_h[h[i_ijWdY[ C_d_ckcZ_c[di_edicc
Feii_Xb[YecX_dWj_edie\a WdZbc_d m^[h[a _ij^[Wl[hW][Wn_iZ_ijWdY[WdZbc_d _ij^[m_Zj^e\j^[X[Wc
Simply supported beams Continuous beams
A B C D E F G H
R60 bmin = 120 160 200 300 120 200
a= 40 35 30 25 25 12a
R90 bmin = 150 200 300 400 150 250
a= 55 45 40 35 35 25
R120 bmin = 200 240 300 500 200 300 450 500
a= 65 60 55 50 45 35 35 30
R240 bmin = 280 350 500 700 280 500 650 700
a= 90 80 75 70 75 60 60 50
Dej[i
' This table is taken from BS EN 1992–1–2 Tables 5.5 and 5.6.
( The axis distance, asd , from the side of the beam to the corner bar should be a +10 mm except where bmin is greater than the values in columns C and F.
) The table is valid only if the detailing requirements (see note 4) are observed and, in normal temperature design, redistribution of bending moments does not exceed 15%.
* For fire resistance of R90 and above, for a distance of 0.3l eff from the centre line of each intermediate support, the area of top reinforcement should not be less than the following:
A s,req (x) = A s,req ( 0 )( 1– 2.5 ( x/ l eff ) )
where:
x is the distance of the section being considered from the centre line of the support.
A s,req ( 0 ) is the area of reinforcement required for normal temperature design.
A s,req (x) is the minimum area of reinforcement required at the section being considered but not less than that required for normal temperature design.
l eff is the greater of the effective lengths of the two adjacent spans.
+ For fire resistances R120 – R240, the width of the beam at the first intermediate support should be at least that in column F, if both the following conditions exist:
W there is no fixity at the end support; and
X the acting shear at normal temperature Vsd > 0.67 V Rd,max .
A[o
a Normally the requirements of BS EN 1992–1–1 will determine the cover.

<_]kh[' <_]kh[)
I[Yj_edj^hek]^ijhkYjkhWbc[cX[h" I_cfb_\_[Zh[YjWd]kbWhijh[iiXbeYa\eh
i^em_d]dec_dWbWn_iZ_ijWdY[ia WdZ aiZ YedYh[j[kfjeYbWii9+&%,&\hec;kheYeZ[(

b εc
ε sc fcd
d2
x As2 0.8x Fsc
Fc
h>b Neutral axis
d
h z
a
As Fst
asd εs
b
Section Strain Stress block and forces
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`-

32
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
4. Beams

<_]kh[(
FheY[Zkh[\ehZ[j[hc_d_d]\b[nkhWbh[_d\ehY[c[dj
a nominal (not minimum) dimension, so the designer
should ensure that: START
cnom + f link + f main bar /2 ≥ amin, where amin is the minimum axis
distance from the fire tables. Carry out analysis of beam to determine
design moments (M) (see Table 3)
Table 2 gives the minimum dimensions for beams to meet the standard
fire periods. Depending on the minimum width of the beam in Table 2,
bmin, the side axis distance, asd, should be checked to ensure that asd ≥ No
Concrete class Outside scope of this
amin + 10 mm. ≤C50/60? publication

Yes

Flexure Determine K from K =

M
bd 2 fck

The design procedure for flexural design is given in Figure 2; this

includes derived formulae based on the simplified rectangular stress Determine K’ from Table 4 or
K’ = 0.60d – 0.18 d2 – 0.21
block from Eurocode 2 Cl. 3.1.7 (3) (see Figure 3). Table 3 may be used where d ≤ 1.0
to determine bending moments and shear forces for beams, provided
the notes to the table are observed. No Compression reinforcement
Is K ≤ K ’ ? required

JWXb[) Cec[dj I^[Wh

Outer support 25% of span moment 0.45 (Gd + Qd )
8[dZ_d]cec[djWdZi^[WhYe[\\_Y_[dji\ehX[Wci Yes
Calculate lever arm z from
Near middle of end span 0.090 Gdl + 0.100 Qd l
z = d 1 + 1 – 3.53 K ’
[ ]
At first interior support – 0.094 (Gd + Qd )l 0.63 (Gd + Qd )a No compression reinforcement required 2

At middle of interior spans 0.066 Gl + 0.086 Ql

At interior supports – 0.075 (Gd + Qd )l 0.50 (Gd + Qd )
Obtain lever arm z from Table 5 or use Calculate compression
A[o reinforcement required from
W 0.55 (Gd+ Qd ) may be used adjacent to the interior span. z= d [1 + 1 – 3.53 K ] ≤ 0.95d
2 (K– K’) fck bd 2
Dej[i As2 =
fsc(d– d2)
' Redistribution of support moments by 15% has been included.
( Applicable to 3 or more spans only and where Qk ≤ G k. where
Calculate tension reinforcement
) Minimum span ≥ 0.85 longest span.
* l is the span, Gd is the total of the ULS permanent actions, Qd is the total
of the ULS variable actions.
required from

As =
M
fsc = 700
[ x – d2
x ] ≤ fyd

fyd z

Table 4
Values for K’ Check minimum reinforcement Calculate tension
requirements (see Table 6) reinforcement required from
% redistribution d (redistribution ratio) K’ x/d 0.26 fctm bt d K’fck bd 2 fsc
As,min = where fck ≥ 25 As = + As2
0 1.00 0.208a 0.6 fyk fyd z fyd
10 0.90 0.182a 0.5
15 0.85 0.168 0.45
Check maximum reinforcement requirements As,max = 0.04 Ac
20 0.80 0.153 0.4 for tension or compression reinforcement outside lap locations
25 0.75 0.137 0.35
30 0.70 0.120 0.3
Key
a It is often recommended in the UK that K’ should be limited to 0.168 to ensure ductile failure. JWXb[ ,
C_d_ckc f[hY[djW][ e\ h[gk_h[Z h[_d\ehY[c[dj

JWXb[+ fYa fYjc C_d_ckcf[hY[djW][&$(,fYjc % foaW

z/d \ehi_d]boh[_d\ehY[Zh[YjWd]kbWhi[Yj_edi

K z/d K z/d
≤0.05 0.950a 0.13 0.868
0.06 0.944 0.14 0.856
0.07 0.934 0.15 0.843
0.08 0.924 0.16 0.830
0.09 0.913 0.17 0.816
0.10 0.902 0.18 0.802
A[o
0.11 0.891 0.19 0.787
W f
0.12 0.880 0.20 0.771
A[o
W Limiting z to 0.95d is not a requirement of Eurocode 2, but is considered to be good practice.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`--- 33
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

<_]kh[*
Ijhkj_dYb_dWj_edc[jêZ D aZl[^^g]^m^kfbg^]nlbg`NDGZmbhgZe:gg^qoZen^lbg>nkh\h]^
IZkm*&*>qi!.'*)'Z"'Ma^D oZen^blkêZm^]mhma^fZqbfnfoZen^h_
q(]pab\ablZeehp^][r>qi!.'*)Z"mh^glnk^ln__b\b^gmkhmZmbhgh_ma^
Concrete strut in compression
l^\mbhg\ZgmZdîeZ\^'Mh^glnk^maZmma^k^bg_hk\^f^gmaZlrbê]^]bm
blh_m^gk^\hff^g]^]bgma^NDmaZmma^fZqbfnfoZen^h_D lahne]
[êbfbm^]mh)'*/1pab\a\hkk^lihg]lmhZfZqbfnfq(]h_)'-.'Mabl
blghmZk^jnbk^f^gmh_>nkh\h]^+%[nmbl\hglb]^k^]mh[^`hh]
y
ikZ\mb\^'

Eurocode 2 gives recommendations for the design of concrete up to

class C90/105.However,for concrete gr^Zm^kmaZg\eZllC50/60,the
Longitudinal Vertical shear
reinforcement in tension reinforcement stress block is modified.It is important to note that concrete strength
is based on the cylinder strength and not the cube strength (i.e.for
class C30/37 the cylinder strength (fck )is 30 MPa,whereas the cube
<_]kh[+ strength is 37 MPa).
FheY[Zkh[\ehZ[j[hc_d_d]l[hj_YWbi^[Whh[_d\ehY[c[dj

START Vertical shear

Determine vEd where Eurocode 2 introduces the strut inclination method for shear capacity
vEd = design shear stress [ vEd = VEd /(bwz) = VEd /(0 9. bwd)] ted by concrete
struts acting in
checks.In this method the shear is resis
compression and shear reinforcement acting in tension.

Determine the concrete strut capacity v Rd, max cot y = 2.5

from Table 7 The angle of the concrete strut varies,depending on the shear force
applied (see Figure 4).The procedure for determining the shear capacity
of a section is shown in Figure 5 (which includes UK NA values) and is
in terms of shear stress in the vertical plane rather than a vertical force
Is No Is No Redesign
vEd < vRd,max coty = 2.5? v Ed < v Rd,max cot y = 1.0? as given in Eurocode 2.Where shear reinforcement is required,then the
section
(see Table 7) angle of the concrete strut should be calculated.For many typical
beams the minimum angle of strut will apply (when cot y= 2.5 or y=
Yes (cot y = 2.5) Yes
21.8º) i.e.for class C30/37 concrete the strut angle exceeds 21.8ºonly
Determine y from: when the shear stress is greater than3./- N/mm2;(refer to Table 7).
vEd
y = 0.5 sin -1 T
0.20 fck (1 – fck /250) V Mhere is a maximum permitted shearcapacity,vRd,max,
(when cot y=1.0 ory= -5º).

Calculate area of shear reinforcement:

Asw
s
=
vEd bw
fywd cot y
Deflection
>nkh\h]^+aZlmphZem^kgZmbo^f^mah]l_hk\a^\dbg`]^_e^\mbhg%^bma^k
Check maximum spacing for vertical shear reinforcement: Zebfbmbg`liZg&mh&]^imakZmbhfZr[^nl^]hkma^ma^hk^mb\Ze
6

s l, max = 0.75 d ]^_e^\mbhg\Zg[^Zll^ll^]nlbg`ma^^qik^llbhgl`bo^gbgma^<h]^'Ma^

eZmm^kbl]^Zempbmabg]^mZbebg<aZim^k1'

JWXb[- Ma^liZg&mh&]îmakZmbhllahne]^glnk^maZm]^_e^\mbhgblebfbm^]mh
C_d_ckcWdZcWn_ckcYedYh[j[ijhkjYWfWY_jo_dj[hcie\ijh[ii liZg(+.)Zg]mablblmaîkh\^]nkîk^l^gm^]bg?b`nk^/'Bmlahne]
fYa v HZ"cWn Yej y 3($+ v HZ"cWn Yej y 3'$& [^ghm^]maZmma^NDGZmbhgZe:gg^qk^\hff^g]lmaZmMlbl\Ze\neZm^]
20 2.54 3.68
nlbg`\aZkZ\m^kblmb\oZen^lZg]ghmjnZlb&i^kfZg^gm
25 3.10 4.50
28 3.43 4.97 oZen^l'
30 3.64 5.28
32 3.84 5.58
35 4.15 6.02
40 4.63 6.72
45 5.08 7.38
50 5.51 8.00
--`,``,,```,,`,`,`,``,`,,

*
34
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
4. Beams

<_]kh[, Figure 4
FheY[Zkh[\ehWii[ii_d]Z[\b[Yj_ed Determination of approximate steel stress at SLS

START

Determine basic l/d and K from Figure 7

Determine Factor 1 (F1)

For flanged sections
F1 = 1 – 0.1 ((bf/bw) – 1) ≥ 0.8†
(bf is flange breadth and bw is rib breadth)
Otherwise F1 = 1.0

Determine Factor 2 (F2)

Where the beam span exceeds 7 m and it supports
brittle partitions, F2 = 7/leff ≤ 1.0
Otherwise F2 = 1.0

Determine Factor 3 (F3)

F3 = As,prov/As,req ≤ 1.5 or 310/ss ≤ 1.5 (UK NA)
where ss is the stress in the reinforcement calculated
under the characteristic combination of SLS loads. ξ
See Figure 8 Increase
As,prov To determine stress in the reinforcement (σs), calculate the ratio Gk/Qk,
read up the graph to the appropriate curve and read across to determine
σsu. σs can be calculated from the expression: σs = σsu (As,req/As,prov) ( 1/δ)
Is basic l/d x K x F1 x F2 x F3 ≥ Actual l/d ?
No

Yes
Check complete

† The Eurocode is ambiguous regarding linear interpolation. It is understood that

it was the intention of the drafting committee that linear interpolation be used
and this is in line with current UK practice.

<_]kh[ -
8Wi_Y ifWd#je#[\\[Yj_l[#Z[fj^ hWj_ei

36
Dej[i
34 ' This graph assumes simply supported span condition
(K = 1.0).
fck = 50 K = 1.5 for interior span condition
32
fck = 45 K = 1.3 for end span condition
K = 0.4 for cantilevers.
30 fck = 40
fck = 35 ( Compression reinforcement, r’, has been taken as 0.
28 fck = 32 ) Curves based on the following expressions:
Span to depth ratio (l/d)

fck = 30
1.5
1.5 fck r 0 r0
26 fck = 28
fck = 25
l
d [
= K 11 +
r
+ 3.2 fck
( )]
r
–1

24
fck = 20 where r ≤ r 0
22
and
20 1.5 fck r 0 fck r’

18
l
d [
= K 11 +
( r – r ’)
+
12 r0 ]
where r > r 0 .
16

12
0.40% 0.60% 0.80% 1.00% 1.20% 1.40% 1.60% 1.80% 2.00%
Percentage of tension reinforcement (A s,req /bd)

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

+
35
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

<_]kh['' <_]kh[/
FheY[Zkh[\ehZ[j[hc_d_d]\b[nkhWbYWfWY_joe\\bWd][ZX[Wci :[\_d_j_ede\le" \ehYWbYkbWj_ede\[\\[Yj_l[\bWd][m_Zj^

START

l0 = 0.85 l1 l0 = 0.15 (l1 + l2 ) l0 = 0.7 l2 l0 = 0.15 l2 + l3

Carry out analysis of beam to determine design
moments, M (see Table 3)
l1 l2 l3

Determine l0 (see Figure 9) and beff from:

beff = (bw + beff1 + beff2) where <_]kh['&
beff1 = (0.2b1 + 0.1 l0) ≤ 0.2 l0 ≤ b1 ;\\[Yj_l[\bWd][m_Zj^fWhWc[j[hi
beff2 = (0.2b2 + 0.1 l0) ≤ 0.2 l0 ≤ b2
Note: The flange width at the support will be beff
different from that at mid-span. beff,1 beff,2
For symbols refer to Figures 9 and 10

bw
M b1 b1 b2 b2
Determine K from K =
bd 2 fck
where b = bw at support b
b = beff in span

<_]kh['(
FbWY_d]e\j[di_edh[_d\ehY[c[dj_d\bWd][ZYheiii[Yj_ed
Determine K’ from Table 4 or
K’ = 0.60d – 0.18 d2 – 0.21 where d ≤ 1.0
beff

As
Calculate lever arm z from
d
z=
2 [
1 + 1 – 3.53 K ≤ 0.95d ] hf

Calculate depth to neutral axis x from: beff1 bw beff2

x = 2.5 (d – z)

Neutral axis in
flange. Design
Yes as rectangular
Is x ≤ 1.25hf ? section (Figure 2)
and then check
longitudinal shear
(Figure 14)
No

<_]kh[')
Neutral axis in web
Calculate moment capacity of flange from:
DejWj_edi\ehj^[Yedd[Yj_edX[jm[[d\bWd][WdZm[X
MR,f = 0.57 fck (beff – bw) hf (d – 0.5hf)

M – MR,f Fd A
and Kf = yf
fck bw d 2
Compressive struts
Fd beff
Dx
Asf
Sf
No
Is Kf ≤ K ’? Redesign section A hf

Yes Longitudinal bar

anchored beyond Fd + D Fd
this projected point
Calculate area of reinforcement required from Check longitudinal
MR,f M – MR,f shear Fd + D Fd
As = + (see Figure 14) bw
fyd (d
fywd (d ––0.5
0.5 hhff)) ffywd
ydzz

36 --`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

Flanged beams C_d_ckc Wh[W e\ i^[Wh h[_d\ehY[c[dj

Ma^fbgbfnfZk^Zh_la^Zkk^bg_hk\^f^gmbg[^Zfl%:lp%fbglahne]
Ma^]^m^kfbgZmbhgh_ma^_eZg`^pb]mabllnffZkbl^]bg?b`nk^l2Zg] [^\Ze\neZm^]_khf
*)'>nkh\h]^+\hgmZbglZ\a^\dmh\hg_bkfmaZmma^la^Zklmk^llZmma^ :lp
4 r p%fbg
bgm^k_Z\^h_ma^_eZg`^Zg]p^[\Zg[^k^lblm^][rma^mkZglo^kl^ l[p
k^bg_hk\^f^gmbgma^_eZg`^'Maîhlbmbhgh_ma^g^nmkZeZqbllahne] pa^k^r p%fbg \Zg[^h[mZbg^]_khfMZ[e^2'
[^]^m^kfbg^]%Zg]ma^gma^Zk^Zh_k^bg_hk\^f^gm\Zg[^\Ze\neZm^]
]î^g]bg`pa^ma^kbmeb^lbgma^_eZg`^hkp^[!l^^?b`nk^**"'
<_]kh[ '*
FheY[Zkh[ \eh Z[j[hc_d_d] bed]_jkZ_dWb i^[Wh YWfWY_jo e\ \bWd][Z X[Wci
:mlniihkmlma^m^glbhgk^bg_hk\^f^gmmhk^lblmah``bg`fhf^gml
lahne][^]blmkb[nm^]Z\khllma^_neepb]mah_ma^^__^\mbo^_eZg`^Zl
lahpgbg?b`nk^*+'Ma^liZg&mh&]îma]^_e^\mbhg\a^\dlnlbg`kZmbhh_ Calculate the longitudinal shear stress
from: vEd = D Fd/(hf D x)
m^glbhgk^bg_hk\^f^gmlahne][^[Zl^]hgZk^Zh_\hg\k^m^Z[ho^ (see Figure 13)
\^gmk^h_m^glbhglm^ê'

Bed]_jkZ_dWbi^[Wh Is length of Yes

Determine the concrete
strut capacity from Table 8
Ma^la^Zklmk^llbgmaô^kmb\ZeieZg^[^mp^^gma^_eZg`^Zg]p^[lahne] flange under consideration or from:
in tension? vRd = 0.195 fck (1 – fck/250)
[^Zll^ll^]Z\\hk]bg`mhl^\mbhg/'+'-Zg]?b`nk^/'0h_>nkh\h]^+
!kîkh]n\^]a^k^Zl?b`nk^*,"'Ma^\aZg`^bg_hk\^bgma^_eZg`^\Zg[^ No
Zll^ll^]_khfma^fhf^gmZg]eô^kZkfZmZiZkmb\neZkeh\Zmbhg'
>nkh\h]^+lmZm^lmaZmma^fZqbfnfe^g`mamaZm\Zg[^\hglb]^k^]_hk Determine the concrete strut capacity
from Table 8 or from:
ma^\aZg`^bg_hk\^blaZe_ma^]blmZg\^[^mp^^gma^fZqbfnffhf^gm vRd = 0.160 fck (1 – fck/250)
Zg]maîhbgmpa^k^ma^fhf^gmbls^kh'<e^Zker%ma^fZqbfnf
ehg`bmn]bgZe_hk\^pbeeh\\nkpa^k^ma^\aZg`^bgfhf^gm%Zg]ma^k^_hk^
_hk\^%blma^`k^Zm^lm4_hkZngb_hkfer]blmkb[nm^]ehZ]hgZ\hgmbgnhnl Determine y f from:
No No
[^Zfmablpbee[^maê^g`mah_[^Zf\ehl^lmmhma^lniihkm' vEd
IsvRZ >vEd?
yf = 0.5 sin-1 T 0.2 fck (1 – fck /250) V IsvRZ >vEd?

?b`nk^*-lahplZ_ehp\aZkm_hkZll^llbg`ma^ehg`bmn]bgZela^Zk Yes (cot y f = 2.0) Yes (cot y f

\ZiZ\bmr4bgfZgr\Zl^lma^mkZglo^kl^k^bg_hk\^f^gmbgma^leZ[pbee[^ = 1.25)

ln__b\b^gmmhk^lblmma^la^Zk_hk\^'Mabl\a^\dblbg\en]^]mh^glnk^maZm Calculate area of transverse reinforcement from:

Asf vEd hf
pa^kîZkmb\neZkermabg_eZg`^lZk^nl^]ma^k^blZ]^jnZm^k^bg_hk\^f^gm' =
s fyd cot y f
Maêhg`bmn]bgZela^Zk\ZiZ\bmrbl[Zl^]hgmaôZkbZ[e^lmknmbg\ebgZmbhg
f^mah]%pab\apZl]^l\kb[^]bgma^l^\mbhghgo^kmb\Zela^Zk'

JWXb[ .
9edYh[j[ ijhkj YWfWY_jo \eh bed]_jkZ_dWb i^[Wh _d \bWd][Z X[Wci
Rules for spacing and fYa v HZ"cWn

quantity of reinforcement +)
Flange in compression
+'2-
Flange in tension
,'.2
+. ,'/) -',2
C_d_ckcWh[We\bed]_jkZ_dWbh[_d\ehY[c[dj +1 ,'21 -'1.
Ma^fbgbfnfZk^Zh_k^bg_hk\^f^gmbl:l%fbg 6)'+/_\mf [ m ](_rd [nm ,) -'++ .'*.
,+ -'-/ .'--
ghme^llmaZg)'))*,[ m]%pa^k^[ m blma^f^Zgpb]mah_ma^m^glbhg
,. -'1+ .'10
shg^!l^^MZ[e^/"'?hkZM&[^Zfpbmama^_eZg`^bg\hfik^llbhg%hger -) .',1 /'..
ma^pb]mah_ma^p^[blmZd^gbgmhZ\\hngmbg\Ze\neZmbg`ma^oZen^h_[ -. .'2) 0'+)
.) /'-) 0'1)
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

CWn_ckcWh[We\bed]_jkZ_dWbh[_d\ehY[c[dj
Ma^fZqbfnfZk^Zh_m^glbhghk\hfik^llbhgk^bg_hk\^f^gm%hnmlb]^ JWXb[/
eZieh\Zmbhgllahne]ghm^q\^^]:l%fZq 6)')-:\ LWbk[i\ehr m"c_d
fYa (& (+ (. )& )( )+ *& *+ +&
C_d_ckcifWY_d]e\h[_d\ehY[c[dj r p%fbgq*) &, )'0+ )'1) )'1. )'11 )'2* )'2. *')* *')0 *'*,
Ma^fbgbfnf\e^Zk]blmZg\^[^mp^^g[Zkllahne][^ma^`k^Zm^kh_3

;Zk]bZf^m^k
:``k^`Zm^lbs^ienl.ff
+)ff
37
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
4. Beams

I[b[Yj[ZiocXebi
IocXeb :[\_d_j_ed LWbk[ IocXeb :[\_d_j_ed LWbk[
:\ <khlll^\mbhgZeZk^Zh_\hg\k^m^ eh =blmZg\^[^mp^^gihbgmlh_s^khfhf^gm
:l :k^Zh_m^glbhglm^ê e(] LiZg&mh&]îmakZmbh
:l+ :k^Zh_\hfik^llbhglm^ê F =^lb`gfhf^gmZmma^NEL
:l% ikho :k^Zh_m^glbhglm^êikhob]^] q =îmamhg^nmkZeZqbl !]&s"()'-
:l% k^jÃ] :k^Zh_m^glbhglm^êk^jnbk^] qfZq EbfbmbgòZen^_hk]îmamhg^nmkZeZqbl !d ¾)'-"] pa^k^d ©*')
[^__ >__^\mbo^_eZg`^pb]ma s Eô^kZkf
[m F^Zgpb]mah_ma^m^glbhgshg^ a \\ <h^__b\b^gmmZdbg`Z\\hngmh_ehg`m^kf )'1._hk_e^qnk^Zg]
^__^\mlhg\hfik^llbo^lmk^g`maZg]h_ ZqbZeehZ]l
[fbg Pb]mah_[^Zfhkkb[
ng_ZohnkZ[e^^__^\mlk^lnembg`_khfma^ *')_hkhma^kia^ghf^gZ
[p Pb]mah_l^\mbhg% hkpb]mah_p^[hg_eZg`^][^Zfl pZrehZ]blZiieb^] !?khfNDGZmbhgZe:gg^q"
] >__^\mbo^]îma d KZmbhh_ma^k^]blmkb[nm^]fhf^gmmhma^
]+ >__^\mbo^]îmamh\hfik^llbhgk^bg_hk\^f^gm êZlmb\[^g]bg`fhf^gm
_\] =^lb`goZen^h_\hg\k^m^\hfik^llbo^lmk^g`ma a\\ _\d (g\ _hk_\d ©<.)(/) gf IZkmbZe_Z\mhk_hkfZm^kbZeikhi^kmb^l *'*._hkk^bg_hk\^f^gm!gl"
*'._hk\hg\k^m^!g\"
_\d <aZkZ\m^kblmb\\rebg]^klmk^g`mah_\hg\k^m^
r) K^_^k^g\^k^bg_hk\^f^gmkZmbh R_\d (*)))
_\mf F^ZgoZen^h_ZqbZem^glbe^lmk^g`ma )',)_\d!+(," _hk_\d ©<.)(/)
!_khfMZ[e^,'*% >nkh\h]^+" r K^jnbk^]m^glbhgk^bg_hk\^f^gmZmfb]&liZg :l([] !_hkk^\mZg`neZk[^Zfl"
mhk^lblmma^fhf^gm]n^mhma^]^lb`g
a_ ?eZg`^mab\dg^ll ehZ]l!hkZmlniihkm_hk\Zgmbeô^kl"
D ?Z\mhkmhmZd^Z\\hngmh_ma^]b__^k^gm L^^mZ[e^G:'-bg rÃ K^jnbk^]\hfik^llbhgk^bg_hk\^f^gmZm :l+([]
lmkn\mnkZelrlm^fl NDGZmbhgZe:gg^q fb]&liZgmhk^lblmma^fhf^gm]n^mhma^
e^__ >__^\mbo^liZgh_f^f[^k L^^L^\mbhg.','+'+!*" ]^lb`gehZ]l!hkZmlniihkm_hk\Zgmbeô^kl"

H[\[h[dY[i
' ;KBMBLALM:G=:K=LBGLMBMNMBHG' ;L>G*22+¾*¾*% >nkh\h]^+3 =^lb`gh_\hg\k^m^lmkn\mnk^l¾IZkm*¾*@^g^kZekne^lZg]kne^l_hk
[nbe]bg`l' ;LB% +))-'
( ;KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22+¾*¾+%>nkh\h]^+3=^lb`gh_\hg\k^m^lmkn\mnk^l'@^g^kZekne^l¾lmkn\mnkZe_bk^]^lb`g';LB%+))-
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

38
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

5. Columns
R Moss BSc, PhD, DIC, CEng, MICE, MIStructE O Brooker BEng, CEng, MICE, MIStructE J Burridge MA CEng MIStructE MICE

Designing to Eurocode 2
This chapter is intended to assist engineers with the design of columns and
walls to Eurocode 21. It sets out a design procedure to follow and gives useful
commentary on the provisions within the Eurocode. European practice is to
give principles and general application rules in the codes and for detailed
application rules to be presented in other sources such as textbooks or
guidance documents. Eurocode 2 does not contain all the formulae that
are needed to design columns and these formulae have to be derived. e.g.
Eurocode 2 does not contain a formula or design charts to calculate the area
of reinforcement, As, to resist an applied ultimate bending moment, M, and
axial load, N. Derived formulae/charts to design columns are given in this
chapter.

It should also be noted that values from the UK National Annex (NA) have
been used throughout this publication, including values that are embedded
in derived formulae. (Derivations can be found at www.concretecentre.com/
eurocode2.) A full list of symbols related to column design is given at the end
of this chapter.

Design procedure
A procedure for carrying out the detailed design of braced columns (i.e.
columns that do not contribute to resistance of horizontal actions) is shown
in Table 1. This assumes that the column dimensions have previously been
determined during conceptual design or by using quick design methods, for
example those presented in Economic concrete frame elements 2. Steps 1 to 4
of Table 1 are covered by earlier chapters and the next step is therefore to
consider fire resistance.

Fire resistance
Eurocode 2, Part 1–2: Structural fire design3 gives a choice of advanced, simplified
or tabular methods for determining fire resistance of columns. Using tables is the
fastest method for determining the minimum dimensions and cover for columns.
There are, however, some restrictions and if these apply further guidance is given in
Chapter 11.
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Rather than giving a minimum cover, the tabular method is based on nominal
axis distance, a (see Figure 1). This is the distance from the centre of the main

Continues page 41

Copyright The Concrete Centre

Table 1
Column design procedure

Step Task Further guidance

Chapter in the publication Standard

1 Determine design life 2: Getting started UK NA to BS EN 1990 Table NA.2.1

2 Assess actions on the column 2: Getting started BS EN 1991 (10 parts) and UK National Annexes

3 Determine which combinations of actions apply 1: Introduction to Eurocodes UK NA to BS EN 1990 Tables NA.A1.1 and NA.A1.2 (B)

4 Assess durability requirements and determine concrete strength 2: Getting started BS 8500: 2015

5 Check cover requirements for appropriate fire resistance period 2: Getting started and Table 2 Approved Document B. BS EN 1992–1–2

6 Calculate min. cover for durability, fire and bond requirements 2: Getting started BS EN 1992–1–1 Cl. 4.4.1

7 Analyse structure to obtain critical moments and axial 2: Getting started and ‘Structural BS EN 1992–1–1 section 5
forces analysis’ section

8 Check slenderness See Figures 2 and 3 BS EN 1992–1–1 section 5.8

9 Determine area of reinforcement required See Figures 2 and 3 BS EN 1992–1–1 section 6.1

10 Check spacing of bars ‘Rules for spacing’ section BS EN 1992–1–1 sections 8 and 9

Note
NA = National Annex.

Figure 1
Table 2
Section through structural member, showing nominal axis distance a
Method A: Minimum column dimensions and axis distances for fire
resistance

Standard fire Minimum dimensions (mm)

resistance
Column width bmin/axis distance, a, of the main
bars
Column exposed on more than Column
one side exposed on h*b
one side
μfi = 0.5 μfi = 0.7 (μfi = 0.7)

R 60 200/36 250/46 155/25

a
300/31 350/40

R 90 300/45 350/53 155/25

400/38 a 450/40 a b

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
R 120 350/45 a 350/57 a 175/35
450/40 a 450/51a
b
Table 3
R 240 450/75 a 295/70 Minimum reinforced concrete wall dimensions and axis distances for
Note
load-bearing walls for fire resistance
The table is taken from BS EN 1992–1–2 Table 5.2a (method A) and is valid under the
following conditions:
Standard Minimum dimensions (mm)
fire
1 The effective length of a braced column under fire conditions lo,fi ≤ 3m. The value of lo,fi resistance Wall thickness/axis distance, a, of the main bars
may be taken as 50% of the actual length for intermediate floors and between 50% Wall exposed on one side Wall exposed on two
and 70% of the actual length for the upper floor column.
(μfi = 0.7) sides (μfi = 0.7)
2 The first order eccentricity under fire conditions should be ≤ 0.15b (or h). Alternatively
use method B (see Eurocode 2, Part 1–2, Table 5.2b). The eccentricity under fire REI 60 130/10 a 140/10 a
conditions may be taken as that used in normal temperature design.
REI 90 140/25 170/25
3 The reinforcement area outside lap locations does not exceed 4% of the concrete
cross section. REI 120 160/35 220/35
4 μfi is the ratio of the design axial load under fire conditions to the design resistance of REI 240 270/60 350/60
the column at normal temperature conditions. μfi may conservatively be taken as 0.7.
Notes
Key
1 The table is taken from BS EN 1992–1–2 Table 5.4.
a Minimum 8 bars
2 See note 4 of Table 2.
b Method B may be used which indicates 600/70 for R 240 and μfi = 0.7.
See BS EN 1992–1–2 Table 5.2b Key
a Normally the requirements of BS EN 1992–1–1 will determine the cover.

40
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
5. Columns

reinforcing bar to the surface of the member. Where there are a For columns there are two tables given in Eurocode 2 Part 1–2 that
number of bars providing resistance it can be considered to be a present methods A and B. Both are equally applicable, although
nominal (not minimum) dimension, and the designer should ensure method A has smaller limits on eccentricity than method B. Method A
that: is slightly simpler and is presented in Table 2; limits of applicability
cnom + f link + f main bar/2 ≥ amin, where amin is the minimum axis distance are given in the notes. Similar data for load-bearing walls is given in
from the fire tables. Table 3.

Figure 2 For columns supporting the uppermost storey, the eccentricity will
Flow chart for braced column design often exceed the limits for both methods A and B. In this situation
Annex C of Eurocode 2, Part 1–2 may be used.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
START

Initial column size may be determined using quick design

Column design
methods or through iteration.
A flow chart for the design of braced columns is shown in Figure 2. For
slender columns, Figure 3 will also be required.
Determine the actions on the column
using an appropriate analysis method.
The ultimate axial load is NEd and the ultimate moments Structural analysis
are Mtop and Mbottom (Moments from analysis)
The type of analysis should be appropriate to the problem being
considered. The following may be used: linear elastic analysis, linear
Determine the effective length, l0, using either:
1. Figure 5 elastic analysis with limited redistribution, plastic analysis and
2. Table 4 non-linear analysis. Linear elastic analysis may be carried out assuming
3. Figure 6
4. Expression (5.15) from BS EN 1992–1–1 cross sections are uncracked (i.e. concrete section properties),
using linear stress-strain relationships and assuming mean values
Determine ﬁrst order moments (see Figure 4) of long-term elastic modulus.
M01 = kMin {|Mtop|, |Mbottom|} + ei NEd
M02 = Max {|Mtop|, |Mbottom|} + ei NEd
Where ei = l0/400 (units to be in millimetres). For the design of columns the elastic moments from the frame action
k = 1 for single curvature, or should be used without any redistribution. For slender columns a
k = -1 for double curvature as illustrated in Figure 4
M01 and M02 should have the same sign non-linear analysis may be carried out to determine the second order
if they give tension on the same side.
moments; alternatively use the moment magnification method
(Cl 5.8.7.3) or nominal curvature method (Cl 5.8.8) as illustrated in
Determine slenderness, l, from either: Figure 3. The latter is expected to be adopted in the UK.
l = l0/i where i = radius of gyration or
l = 3.46 l0/h for rectangular sections (h = overall depth) or
l = 4.0 l0/d for circular sections (d = column diameter) Design moments for a braced column
The design bending moment is illustrated in Figure 4 and defined as:
Determine slenderness limit, hlim, from: MEd = Max {M02, M0e + M2, |M01 - 0.5 M2 - 2eiNEd | , e0NEd}
l 15.4C
lim =
3n where
(See ‘Slenderness’ section on page 43 for explanation.)
M01 = kMin {|Mtop|, |Mbottom|} + ei NEd
M02 = Max {|Mtop|, |Mbottom|} + ei NEd
where:
Yes
Column is slender k = 1 for single curvature, or
Is l * l lim? (refer to Figure 3).
k = -1 for double curvature as illustrated in Figure 4
No e0 = Max {h/30, 20} (mm)
ei = l0/400 (mm)
Column is not slender
MEd = M02 ≥ NEd e0 Mtop, Mbottom = Moments at the top and bottom of the column
where e0 = Max (h/30, 20) M0e = 0.6 M02 + 0.4 M01 ≥ 0.4 M02
(units to be in millimetres)
M2 = NEd e2 where NEd is the design axial load and e2
is deflection due to second order effects
Use column chart (see Figure 10) to ﬁnd As required for
NEd and MEd. Alternatively, solve by iteration or by using RC M01 and M02 should be positive if they give tension on the same side.
Spreadsheet TCC53 from Spreadsheets for concrete design to
BS 8110 and Eurocode 2 4 A non-slender column can be designed ignoring second order effects
and therefore the ultimate design moment, MEd = Max {M02, e0NEd}.
Check rules for spacing and quantity of reinforcement
(see page 50 and 51)
The calculation of the eccentricity, e2, is not simple and is likely to
require some iteration to determine the deflection at approximately
mid-height, e2. Guidance is given in Figure 3.
41
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Figure 3 Effective length

Flow chart for slender columns (nominal curvature method)
Figure 5 gives guidance on the effective length of the column.
However, for most real structures Figures 5f) and 5g) only are
From Figure 2 applicable, and Eurocode 2 provides two expressions to calculate the
effective length for these situations. Expression (5.15) is for braced
Determine Kr from Figure 10 or from members and Expression (5.16) is for unbraced members.
Kr = (nu - n) / (nu - nbal) ) 1
where
n = NEd / (Ac fcd), relative axial force In both expressions, the relative flexibilities at either end, k1 and
NEd = the design value of axial force
nu = 1 + w k2, should be calculated. The expression for k given in the Eurocode
nbal = 0.4 involves calculating the rotation of the restraining members, which in
w = As,est fyd / (Ac fcd)
As,est = the estimated total area of steel practice requires the use of framework analysis software. Alternatively,
Ac = the area of concrete
PD 6687: Background paper to the UK National annex 5 provides a
simplification, based on the stiffness of the beams attached to either
Calculate Kh from Kh = 1 + b hef * 1 side of the column. This relative stiffness, k, can therefore be calculated
where
hef = the effective creep ratio as follows (provided the stiffness of adjacent columns does not vary by
b = 0.35 + fck/200 – h/150
l = the slenderness ratio.
more than 15% of the higher stiffness):
See section on creep (page 44)
EIc 2EIb
k= Y * 0.1
lc lb
Calculate e2 from

e2 = 0.1 ( K0.45d
rK f
E
)l
h yd
s
0
2
Revise value
of As,est
where
where Ic, Ib are the column and beam uncracked second moments of area
Es = elastic modulus of reinforcing steel
(200 GPa)
lc, lb are the column and beam lengths

Once k1 and k2 have been calculated, the effective length factor, F, can
M0e = 0.6 M02 + 0.4 M01 * 0.4 M02 be established from Table 4 for braced columns. The effective length is
M2 = NEd e2
then lo = Fl.
MEd = Max {M02, M0e + M2, |M01 - 0.5 M2 - 2eiNEd|, e0 NEd}
where
ei = l0/400 The value of k is not particularly sensitive to the column length, and
e0 = Max (h/30, 20)
(units to be in millimetres) since most beams and slabs have similar span-to-depth ratio it is
possible to construct a graph that gives an indication of the effective
length factor, F, (see Figure 6). A key decision is whether the column is
Use column chart to ﬁnd As,req for NEd and MEd
Alternatively, solve by iteration or by using notionally pinned at one end.
RC Spreadsheet4
Figure 4
Design bending moments for a braced slender column

No
M02
Is As req & As, est?
M ei NEd M02

Yes
Check detailing requirements
M0e + M2

M2 = NEd e2
Figure 5
Effective lengths for isolated members
+ =

M01 0.5 M2 M01 - 0.5M2 - 2eiNEd

First order Additional second Envelope of design
y moments for order moments for moments for a
y ‘stocky’ columns ‘slender’ columns ‘slender’ column
l

y Note:
M • Design moments are based on PD66875 guidance
• ei should be considered in opposite directions: that may alter the location of
a) l0 = l b) l0 = 2l c) l0 = 0.7l d) l0 = l /2 e) l0 = l f) l/2 < l0 < l g) l0 > 2l M01 and M02
• ei = 0 may be a worse case
• e2 = 0 in non-slender columns and e2 = 0 may be critical in slender columns
• At about mid-height, M2 has same sign as M02
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

42
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
5. Columns

Figure 6
Effective length factor, F, for braced columns

Figure 7 Slenderness, l = lo/i where i = radius of gyration and slenderness limit.

Calculating factor C
20ABC 15.4C
l lim = )
105 kNm 105 kNm 105 kNm n n
where
A = 1/(1+0.2 hef) (if hef is not known, A = 0.7 may be used)
B= (if t, reinforcement ratio, is not known,
B = 1.1 may be used)
105 kNm 0 105 kNm
rm = 1.0 rm = 0 rm = -1.0
C = 1.7 – rm (if rm is not known, C = 0.7 may be used – see below)
n = NEd / (Ac fcd)
a) C = 1.7 - 1 = 0.7 b) C = 1.7 - 0 = 1.7 c) C = 1.7 + 1.0 = 2.7 rm = M01/M02
M01, M02 are the first order end moments, |M02| ≥ |M01|
Figure 8
Stress block diagram for columns If the end moments M01 and M02 give tension on the same side,
rm should be taken positive.
f cd d2
ecu 2 s sc
esc As2 Of the three factors A, B and C, C will have the largest impact on
dc
x
l lim and is the simplest to calculate. An initial assessment of l lim can
h therefore be made using the default values for A and B, but including a
n. axis
d2
calculation for C (see Figure 7). Care should be taken in determining C
ey As
because the sign of the moments makes a significant difference. In the
s st
following cases C should be taken as 0.7:
a) Strain diagram b) Stress diagram
– for braced members in which the first order moments arise only
from or predominantly due to imperfections or transverse loading
Slenderness
Eurocode 2 states that second order effects may be ignored if they – for unbraced members
are less than 10% of the first order effects. As an alternative, if the
slenderness (l) is less than the slenderness limit (l lim), then second
order effects may be ignored.
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`--- 43
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Table 4 Column design resistance

Effective length factor, F, for braced columns
For practical purposes the rectangular stress block used for the
k2 k1 design of beams (see Chapter 4) may also be used for the design of
0.10 0.20 0.30 0.40 0.50 0.70 1.00 2.00 5.00 9.00 Pinned columns (see Figure 8). However, the maximum compressive strain for
concrete classes up to and including C50/60, when the whole section
0.10 0.59 0.62 0.64 0.66 0.67 0.69 0.71 0.73 0.75 0.76 0.77
is in pure compression, is 0.00175 (see Figure 9a). When the neutral axis
0.20 0.62 0.65 0.68 0.69 0.71 0.73 0.74 0.77 0.79 0.80 0.81
falls outside the section (Figure 9b), the maximum allowable strain is
0.30 0.64 0.68 0.70 0.72 0.73 0.75 0.77 0.80 0.82 0.83 0.84
assumed to lie between 0.00175 and 0.0035, and may be obtained by
0.40 0.66 0.69 0.72 0.74 0.75 0.77 0.79 0.82 0.84 0.85 0.86 drawing a line from the point of zero strain through the ‘hinge point’
0.50 0.67 0.71 0.73 0.75 0.76 0.78 0.80 0.83 0.86 0.86 0.87 of 0.00175 strain at mid-depth of the section. When the neutral axis
0.70 0.69 0.73 0.75 0.77 0.78 0.80 0.82 0.85 0.88 0.89 0.90 lies within the section depth then the maximum compressive strain is
1.00 0.71 0.74 0.77 0.79 0.80 0.82 0.84 0.88 0.90 0.91 0.92 0.0035 (see Figure 9c).
2.00 0.73 0.77 0.80 0.82 0.83 0.85 0.88 0.91 0.93 0.94 0.95 The general relationship is shown in Figure 9d). For concrete classes
above C50/60 the principles are the same but the maximum strain
5.00 0.75 0.79 0.82 0.84 0.86 0.88 0.90 0.93 0.96 0.97 0.98
values vary.
9.00 0.76 0.80 0.83 0.85 0.86 0.89 0.91 0.94 0.97 0.98 0.99
Pinned 0.77 0.81 0.84 0.86 0.87 0.90 0.92 0.95 0.98 0.99 1.00

Figure 9
Strain diagrams for columns

0.00175 0.00175 x / ( x – h /2) 0.0035 max 0.0035 max

x x
h/ 2
hinge hinge
h point h d point
x
ex ex

0.00175 0.00175 min

a) Pure compression b) When x > h c) When x < h d) General relationship

Two expressions can be derived for the area of steel required, (based on Creep
a rectangular stress block, see Figure 8) one for the axial loads and the Depending on the assumptions used in the design, it may be necessary
other for the moments: to determine the effective creep ratio hef (ref. Cl. 3.1.4 & 5.8.4). A
AsN /2 = (NEd – fcd b dc) / (msc – mst) nomogram is provided in the Eurocode (Figure 3.1) for which the cement
where strength class is required; however, at the design stage it is often not
AsN = Area of reinforcement required to resist axial load certain which class applies. Generally, Class R should be assumed. Where
NEd = Axial load the ground granulated blastfurnace slag (ggbs) exceeds 35% of the
fcd = Design value of concrete compressive strength cement combination or where fly ash (fa) exceeds 20% of the cement
msc (mst) = Stress in compression (and tension) reinforcement combination, Class N may be assumed. Where ggbs exceeds 65% or
b = Breadth of section where fa exceeds 35%, Class S may be assumed.
dc = Effective depth of concrete in compression = lx ≤ h
l = 0.8 for ≤ C50/60
x = Depth to neutral axis Biaxial bending
h = Height of section
The effects of biaxial bending may be checked using Expression (5.39),
AsM /2 = [M – fcd b dc(h/2 – dc/2)] / [(h/2–d2) (msc+mst)] which was first developed by Breslaer.
where MEdz a MEdy a

AsM = Total area of reinforcement required to resist moment ( ) + ( ) ) 1.0

MRdz MRdy

where
Realistically, these can only be solved iteratively and therefore either
MEdz/y = Design moment in the respective direction including second
computer software (e.g. RC Spreadsheet TCC53 from Spreadsheets for
order effects in a slender column
concrete design to BS 8110 and EC24) or column design charts (see
MRdz/y = Moment of resistance in the respective direction
Figures 10a to 10e) may be used for rectangular columns and Figures
a = 2 for circular and elliptical sections; refer to Table 5 for rectangular
11a to 11f may be used for circular columns.
sections
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`--- NRd = Ac fcd + As fyd
44 Continues page 50
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
5. Columns

Figure 10a
Column design chart for rectangular columns d2 /h = 0.05

*',
D k 6)'+ KZmbh] + (a 6)').
*'+
\d
)', a_
*'* ([ a(+
_l r d
: a
*') )'-
*')
)'2 ]+
)'2 )'1 <^gmkhb]h_[Zklbg
)'.
)'0 aZe_l^\mbhg
)'1 )'/
)'. )'/
G>] ([a_\d

)'0 )'-
)', )'0
)'/
)'+
)'. )'*
)'1
)
)'-
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

)'2
)',
*')
)'+

)'*

)
) )'). )'*) )'*. )'+) )'+. )',) )',. )'-) )'-.
F>]([a+_\d

Figure 10b
Column design chart for rectangular columns d2 /h = 0.10

*',
D k 6)'+
KZmbh] + (a 6)'*)
*'+
\d

)',
[a_

a(+
d(

*'*
l _r

a
:

*') )'-
*')
)'2 ]+
)'2 )'1
)'. <^gmkhb]h_[Zklbg
)'0 aZe_l^\mbhg
)'1 )'/
)'. )'/
G>] ([a_\d

)'0 )'-
)', )'0
)'/
)'+
)'. )'*
) )'1
)'-
)'2
)',
D k 6*
)'+

)'*

)
) )'). )'*) )'*. )'+) )'+. )',) )',. )'-) )'-.
F>] ([a+_\d

45
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Figure 10c
Column design chart for rectangular columns d2 /h = 0.15

*',
D k 6)'+
KZmbh] + (a 6)'*.
*'+

\d
)',

a_
a(+

([
*'*

rd
a

_
l
:
*') *')
)'- ]+
)'2
)'2 )'1
)'. <^gmkhb]h_[Zklbg
)'0 aZe_l^\mbhg
)'1
)'/
)'/
G>] ([a_\d

)'.
)'0
)'-
)'/ )', )'0
)'+
)'. )'*
) )'1
)'-
)'2
)',
D k 6*
)'+

)'*

)
) )'). )'*) )'*. )'+) )'+. )',) )',. )'-)
F>] ([a+_\d

Figure 10d
Column design chart for rectangular columns d2 /h = 0.20

*',
D k 6)'+
KZmbh] + (a 6)'+)
*'+
\d
a_
([

)', a(+
d

*'*
_r
l
:

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
*') *')
)'- ]+
)'2
)'2 )'1 <^gmkhb]h_[Zklbg
)'0 )'. aZe_l^\mbhg
)'1 )'/
)'. )'/
G>] ([a_\d

)'0
)'-
)'/ )',
)'+ )'0
)'. )'*
) )'1
)'-

)', )'2

)'+
D k 6*
)'*

)
) )'). )'*) )'*. )'+) )'+. )',) )',.
F>] ([a+_\d

46
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
5. Columns

Figure 10e
Column design chart for rectangular columns d2 /h = 0.25

*',
D k 6)'+ KZmbh] + (a 6)'+.
*'+
)', a(+

\d
*'*

a_
([
a

d
_r
*')

l
:
*') ]+
)'-
)'2 )'2
<^gmkhb]h_[Zklbg
)' 1 aZe_l^\mbhg
)'1 )'0
)'.
)'/
G>] ([a_\d

)'0 )'.
)'- )'/
)'/ )',
)'+
)'. )'* )'0
)
)'-
)'1
)',
)'2
)'+

)'*
D k 6*
)
) )'). )'*) )'*. )'+) )'+. )',)
F>] ([a+_\d

Figure 11a
Circular columns ( fck < 50 MPa, fyk = 500 MPa) d/h = 0.5

1.2
0.3 As fyk/h2fck Ratio d/h = 0.5
1.1
1.0
0.4 d
h
1.0 0.9 0.5

0.8 0.6
0.9
0.7 0.7
0.8 0.6 0.8
0.5
NEd /h2fck

0.7
0.9
0.4
0.6
0.3 Kr = 1
0.5 0.2
0.1
0.4 0

0.3

0.2
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

0.1

0
0 0.005 0.010 0.015 0.020 0.025 0.030 0.035 0.040 0.045 0.050
MEd /h3fck

Circular columns ( f 50 MPa)

47
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Figure 11b
Circular columns (fck ≤ 50 MPa, fyk = 500 MPa) d/h = 0.6

*'+
:l _rd (a+_\d KZmbh](a 6)'/
)'+
*'*
*') ]
)', a
*') )'2
)'1 )'-
)'2
)'0
)'1 )'.
)'/
)'0 )'.
)'/
G>] (a+_\d

)'-
)'/ )', )'0
)'+
)'.
)'* )'1
)'- )

)', )'2

)'+
Dk6*

)'*

)
) )')* )')+ )'), )')- )'). )')/ )')0
F>] (a,_\d

Figure11c
Circular columns (fck ≤ 50 MPa, fyk = 500 MPa) d/h = 0.7

*'+
)'+ KZmbh](a 6)'0
*'* :l _rd (a+_\d
]
*') a
*')
)',
)'2
)'2 )'1
)'-
)'0
)'1
)'/
)'0 )'.
)'.
G>] (a+_\d

)'-
)'/
)',
)'/
)'. )'+
)'*
)'0
)'- )

)',
)'1
)'+
Dk6*
)'*

)
) )')+ )')- )')/ )')1 )'*) )'*+
F>] (a,_\d

48
--`,``,,```,,`,`,`

Copyright The Concrete Centre

Figure 11d
Circular columns (fck ≤ 50 MPa, fyk = 500 MPa) d/h = 0.8

*'+
)'+ KZmbh](a 6)'1
*'* :l _rd(a+_\d
]
*') )', a
*')
)'2
)'2 )'1
)'-
)'0
)'1
)'/
)'.
)'0 )'.
)'-
G>] (a+_\d

)'/ )', )'/

)'. )'+
)'* )'0
)'- )
)'1
)',

)'+ )'2

)'*
Dk6*
)
) )')+ )')- )')/ )')1 )'*) )'*+ )'*- )'*/ )'*1 )'+)
F>] (a,_\d

Figure 11e

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
Circular columns (fck ≤ 50 MPa, fyk = 500 MPa) d/h = 0.85

*'+
KZmbh](a 6)'1.
)'+ :l _rd (a+_\d
*'*
] a
*') *') )',
)'2
)'2 )'1
)'-
)'0
)'1
)'/
)'0 )'. )'.
)'-
G>] (a+_\d

)'/
)', )'/
)'. )'+
)'* )'0
)'- )

)', )'1

)'+
)'2
)'*
Dk6*

)
) )'). )'*) )'*. )'+) )'+.
F>] (a,_\d

49
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Figure 11f
Circular columns (fck ≤ 50 MPa, fyk = 500 MPa) d/h = 0.9

*'+
)'+ KZmbh](a 6)'2
:l _rd(a+_\d
*'*
*') )', ] a
*')
)'2
)'2 )'1 )'-
)'0
)'1
)'/
)'.
)'0 )'.
)'-
G>] (a+_\d

)'/ )'/
)',
)'. )'+
)'* )'0
)'- )
)'1
)',

)'+ )'2

)'* Dk6*

)
) )'). )'*) )'*. )'+) )'+. )',)
F>] (a,_\d

■ There are different rules for spacing and quantity of reinforcement

Table 5
Value of a for rectangular sections (see below).

0.1 0.7 1.0 There is no specific guidance given for bending about the strong axis
NEd /NRd
for stability. However, the principles of CIRIA Report 1086 may be
a 1.0 1.5 2.0
followed. Alternatively the strut and tie method may be used (section
Note
Linear interpolation may be used. 6.5 of Eurocode 2).

Unbraced columns Rules for spacing and

There is no comment made on the design of sway frames in Eurocode 2.
quantity of reinforcement
However, it gives guidance on the effective length of an unbraced
member in Expression (5.16). The value for C of 0.7 should always be
Maximum areas of reinforcement
In Eurocode 2 the maximum nominal reinforcement area for columns
used in Expression (5.13N). The design moments should be assessed
and walls outside laps is 4%. However, this area can be increased
including second order effects. The tabular method for fire resistance
provided that the concrete can be placed and compacted sufficiently.
design (Part 1–2) does not explicitly cover unbraced columns; however
If required self-compacting concrete may be used for particularly
reference can be made to the Chapter 11.
congested situations, where the reinforcing bars should be spaced to
ensure that the concrete can flow around them. Further guidance can

Walls be found in Self-compacting concrete.7

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

When the section length of a vertical element is four times greater Minimum reinforcement requirements
than its thickness it is defined as a wall. The design of walls does not The recommended minimum diameter of longitudinal reinforcement in
differ significantly from that for columns except for the following: columns is 12 mm. The minimum area of longitudinal reinforcement in
■ The requirements for fire resistance (see Table 3). columns is given by: As,min = 0.10 NEd/fyd ≥ 0.002Ac Exp. (9.12N)
■ Bending will be critical about the weak axis. The diameter of the transverse reinforcement should not be less than
6 mm or one quarter of the maximum diameter of the longitudinal bars.

50
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
5. Columns

Spacing requirements for columns Selected symbols

The maximum spacing of transverse reinforcement (i.e. links) in Symbol Definition Value
columns (Clause 9.5.3(1)) should not exceed: 1/r0 Reference curvature ¡yd/(0.45 d)
■ 12 times the minimum diameter of the longitudinal bars. 1/r Curvature Kr Kh 1/r0
■ 60% of the lesser dimension of the column. a Axis distance for fire resistance
■ 240 mm.
A Factor for determining slenderness limit 1 / (1+0.2 hef)
At a distance greater than the larger dimension of the column above
Ac Cross sectional area of concrete bh
or below a beam or slab these spacings can be increased by a factor
As Area of total column reinforcement
of 1.67. The minimum clear distance between the bars should be the
B Factor for determining slenderness limit
greater of the bar diameter, aggregate size plus 5 mm or 20 mm.
No longitudinal bar should be further than 150 mm from transverse c Factor depending on curvature distribution 10 (for constant cross-section)

reinforcement (links) in the compression zone. C Factor for determining slenderness limit 1.7 – rm

d Effective depth
Particular requirements for walls e2 Second order eccentricity (1/r)l0/c
The minimum area of vertical reinforcement in walls is given by: ei Eccentricity due to geometric imperfections

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
Es Elastic modulus of reinforcing steel 200 GPa
As,min = 0.002Ac
fcd Design value of concrete compressive strength _cc fck/ac
Half of this area should be located at each face. The distance between fck Characteristic cylinder strength of concrete
two adjacent vertical bars should not exceed the lesser of either three l Clear height of compression member between
times the wall thickness or 400 mm. end restraints

l0 Effective length
The minimum area of horizontal reinforcement in walls is the greater
Kr Correction factor depending on axial load
of either 25% of vertical reinforcement or 0.001 Ac. However, where
Kh Factor taking into account creep
crack control is important, early age thermal and shrinkage effects
M01,M02 First order moments including the effect of
should be considered explicitly. geometric imperfections |M02| ≥ |M01|

M2 Nominal second order moment NEd e2

M0e Equivalent first order moment 0.6 M02 + 0.4 M01 ≥ 0.4 M02

MEd Ultimate design moment

MEqp First order bending moment under

quasi-permanent loading

n Relative axial force NEd/(Acfcd)

nbal Value of n at maximum moment of resistance 0.4

nu Factor to allow for reinforcement in the column 1 +t

NEd Ultimate axial load

rm Moment ratio M01/M02

x Depth to neutral axis (d – z)/0.4

z Lever arm

_cc Coefficient taking account of long term effects 0.85 for flexure and axial
on compressive strength and of unfavourable loads. 1.0 for other
effects resulting from the way load is applied phenomena (From UK NA)

` Factor 0.35 + fck/200 – h/150

¡yd Design value of strain in reinforcement fyd/Es

am Partial factor for material properties 1.15 for reinforcement (as)

1.5 for concrete (ac)

l Slenderness l0/i

l lim Slenderness limit

μfi Degree of utilisation in a fire NEd,fi /NRd

hef Effective creep ratio h(',to) MEqp /MEd

h (',t0) Final creep co-efficient to Cl 3.1.4

t Mechanical reinforcement ratio As fyd/(Ac fcd)

|x| Absolute value of x

Max. {x,y+z} The maximum of values x or y + z

51
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
References
1 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–1, Eurocode 2: Design of concrete structures. General rules and rules for buildings. BSI, 2004.
2 GOODCHILD, C H, ELIOTT, KS & WEBSTER, RM. Economic concrete frame elements. The Concrete Centre, 2009.
3 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–2. Eurocode 2: Design of concrete structures. General rules – structural fire design. BSI, 2004.
4 GOODCHILD, C H & WEBSTER, R M. Spreadsheets for concrete design to BS 8110 and Eurocode 2, version 3. The Concrete Centre, 2006.
5 BRITISH STANDARDS INSTITUTION. PD6687-1, Background paper to the UK National Annex to BS EN 1992–1–1 and BS EN 1992–1–2. BSI, 2010.
6 CIRIA. Report 102: Design of shear wall buildings. CIRIA, 1984.
7 THE CONCRETE SOCIETY. Technical Report No 62: Self-compacting concrete. A review, 2005.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
52
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

6. Foundations
R Webster CEng, FIStructE O Brooker BEng, CEng, MICE, MIStructE, MCS J Burridge MA CEng MIStructE MICE

Eurocode 7: Geotechnical Geotechnical Categories

Eurocode 7 recommends three Geotechnical Categories to assist in

design establishing the geotechnical design requirements for a structure (see Table
1). It is anticipated that structural engineers will take responsibility for
the geotechnical design of category 1 structures, and that geotechnical
Scope engineers will take responsibility for category 3 structures. The
All foundations should be designed so that the soil safely resists the
geotechnical design of category 2 structures may be undertaken by
actions applied to the structure. The design of any foundation consists
members of either profession. This decision will very much depend on
of two components; the geotechnical design and the structural design
individual circumstances.
of the foundation itself. However, for some foundations (e.g. flexible
rafts) the effect of the interaction between the soil and structure may Methods of design and combinations
be critical and must also be considered. Geotechnical design is covered There has not been a consensus amongst geotechnical engineers
by Eurocode 71. The Eurocode uses limit state principles throughout over the application of limit state principles to geotechnical design.
to ensure consistency with other Eurocodes. There are two parts to Therefore, to allow for these differences of opinion, Eurocode 7
Eurocode 7, Part 1: General rules and Part 2: Ground investigation and provides for three Design Approaches to be used for the ULS. The
testing. Guidance on the design of retaining walls can be found in decision on which approach to use for a particular country is given in
Chapter 9. its National Annex. In the UK Design Approach 1 has been adopted
in the National Annex. For this Design Approach (excluding pile and
The essential features of Eurocode 7, Part 1 relating to foundation
anchorage design) there are two sets of combinations to use for the
design are discussed in this chapter. It should be emphasised that this
STR and GEO ultimate limit states. The values for the partial factors
publication covers only the design of simple foundations, which are a
to be applied to the actions for these combinations of partial factors
small part of the scope of Eurocode 7. Therefore it should not be relied
are given in Table 2 and the partial factors for the geotechnical material
on for general guidance on this Eurocode.
properties are given in Table 3. Combination 1 will generally govern the
structural resistance, and Combination 2 will generally govern the sizing
BS 80042 was revised in 2015 to provide non-contradictory
of the foundations.
information, for use in conjunction with Eurocode 7.

The partial factors for soil resistance to sliding and bearing should be
Limit states
taken as 1.0 for both combinations.
The following ultimate limit states (ULS) should be satisfied for
geotechnical design; they each have their own combinations of actions.
The partial factors to be applied to the actions at the EQU limit state
(For an explanation of Eurocode terminology please refer to Chapter 1.)
are given in Table 4; the geotechnical material partial factors are given
EQU Loss of equilibrium of the structure.
in Table 3.
STR Internal failure or excessive deformation of the structure or
structural member. For the SLS, Eurocode 7 does not give any advice on whether the
GEO Failure due to excessive deformation of the ground. characteristic, frequent or quasi-permanent combination should be
UPL Loss of equilibrium due to uplift by water pressure. used. Where the prescriptive method is used for spread foundations
HYD Failure caused by hydraulic gradients. (see page 55) then the characteristic values should be adopted. For
direct methods of calculation the frequent combination can be used
In addition, the serviceability limit states (SLS) should be satisfied. It
for sizing of foundations and the quasi-permanent combination can be
will usually be clear that one of the limit states will govern the design
used for settlement calculations.
and therefore it will not be necessary to carry out checks for all of
them, although it is considered good practice to record that they have
all been considered.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

Geotechnical design report

A geotechnical design report should be produced for each project,
Spread foundations
even if it is only a single sheet. The report should contain details of
The geotechnical design of spread foundations (e.g. strip and pad
the site, interpretation of the ground investigation report, geotechnical
foundations) is covered by section 6 of Eurocode 7, Part 1 and this
design recommendations and advice on supervision, monitoring and
gives three methods for design:
maintenance of the works. It is likely that this report will require input
■ Direct method – calculation is carried out for each limit state.
from more than one consultant, depending on whether the project is
■ Indirect method – experience and testing used to determine
in Geotechnical Category 1, 2 or 3.
serviceability limit state parameters that also satisfy all relevant
The foundation design recommendations should include bearing limit states (included in Eurocode 7 mainly to suit French design
resistances and characteristic values for soil parameters. It should methods, and is not discussed further here).
also clearly state whether the values are applicable to SLS or ULS and ■ Prescriptive method in which a presumed bearing resistance is used.

whether they are for Combination 1 or Combination 2.

For most spread foundations in the UK, settlement will be the
governing criterion; traditionally ‘allowable bearing pressures’ have been
used to limit settlement. This concept of increasing the factor of safety

Table 1
Geotechnical categories of structures

Category Description Risk of geotechnical failure Examples from Eurocode 7

1 Small and relatively simple structures Negligible None given

2 Conventional types of structure and foundation No exceptional risk Spread foundations

with no difficult ground or loading conditions
3 All other structures Abnormal risks Large or unusual structures
Exceptional ground conditions

Table 2
Design values of actions derived for UK design, STR/GEO ultimate limit state – persistent and transient design situations

Combination Permanent actions Leading variable Accompanying variable actions

Expression reference action
from BS EN 1990 Unfavourable Favourable Main (if any) Others
Combination 1 (Application of combination 1 (BS EN 1997) to set B (BS EN 1990))

Exp. (6.10) 1.35 Gka 1.0 Gka 1.5b Qk – 1.5b co,i c Qk,i
Exp. (6.10a) 1.35 Gka 1.0 Gka – 1.5 co,1c Qk 1.5b co,i c Qk,i

Exp. (6.10b) 0.925d x 1.35 Gka 1.0 Gka 1.5b Qk – 1.5b co,i c Qk,i

Combination 2 (Application of combination 2 (BS EN 1997) to set C (BS EN 1990))

Exp. (6.10) 1.0 Gka 1.0 Gka 1.3b Qk,1 – 1.3b co,i c Qk,i

Key
a Where the variation in permanent action is not considered significant Gk,j,sup and Gk,j,inf may be taken as Gk
b Where the action is favourable, gQ,i = 0 and the variable actions should be ignored
c The value of c o can be obtained from Table NA.A1.1 of the UK NA to BS EN 1990 (or see Table 2 of Chapter 1)
d The value of j in the UK NA to BS EN 1990 is 0.925

Table 3
Partial factors for geotechnical material properties

Angle of shearing resistance Effective cohesion Undrained shear Unconfined Bulk density
(apply to tan h) strength strength

Symbol gh gc’ gcu gqu gg

Combination 1 1.0 1.0 1.0 1.0 1.0
Combination 2 1.25 1.25 1.4 1.4 1.0

EQU 1.1 1.1 1.2 1.2 1.0

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

54
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
6. Foundations

on bearing resistances to control settlement may still be used with the The prescriptive method may be used where calculation of the soil
prescriptive method. The exception is for soft clays where Eurocode 7 properties is not possible or necessary and can be used provided that
requires settlement calculations to be undertaken. conservative rules of design are used. The latest version of BS 8004 no
longer contains a table of presumed allowable bearing values under
When using the direct method, calculations are carried out for each static loading. Table 5 provides presumed allowable bearing values that
limit state. At the ULS, the bearing resistance of the soil should be are compatible with BS 8004 and Eurocode 7 for category 1 structures.
checked using partial factors on the soil properties as well as on Alternatively, the presumed bearing resistance to allow for settlement
the actions. At the SLS the settlement of the foundations should be can be calculated by the geotechnical designer and included in the
calculated and checked against permissible limits. geotechnical design report.

Table 4
Design values of actions derived for UK design, EQU ultimate limit
state – persistent and transient design situations

Combination Permanent actions Leading Accompanying variable

Expression variable actions
reference action
Unfavourable Favourable Main Others
(if any)
Exp. (6.10) 1.1 Gka 0.90 Gka 1.5b Qk – 1.5b co,i c Qk,i

Key
a Where the variation in permanent action is not considered significant Gk, j, sup
and Gk, j, inf may be taken as Gk
b Where the action is favourable, gQ, i = 0 and the variable actions should be ignored
c The value of co can be obtained from Table NA.A1.1 of the UK NA to BS EN 1990

Table 5
Presumed allowable bearing values under static loading

Typical drained Max. bearing pressure, 2,3

Description1 Density Density index, ID (%) Dimensions4
strength, { (deg) qk,max (kPa)

Coarse soils
Very dense 85-100 43 600
Dense 65-85 40 350
GRAVEL Medium dense 36-65 37 225 B ≥ 1.0 m
Loose 15-35 34 125
d ≥ 500 mm
Very loose 0-15 Seek specialist advice
dw ≥ d
Very dense 85-100 39 300
For B < 1.0, see BS
Dense 65-85 36 200
SAND Medium dense 36-65 33 125 8103-1:2011 instead
Loose 15-35 30 75
Very loose 0-15 Seek specialist advice
Fine soils
Undrained strength, Max. bearing pressure,3,5
Description1 Strength Consistency
cu (kPa) qk,max (kPa)
Warning

Extremely high Hard ≥ 300 580

Very high Very stiff 150-300 290 Foundation is
CLAY High Stiff 75-150 150 susceptible to
or Medium Firm 40-75 80 long-term
SILT Low Soft 20-40 40 consolidation
Very low 10-20 settlement
Very soft Seek specialist advice
Extremely low ≤ 10
1Soilclassiﬁcation according to BS EN ISO 14688
2Maximum characteristic bearing pressure to be applied to the ground: qk,max = (Gk + Qk)/B, assuming permanent and variable actions are equal in magnitude, i.e. Qk /(Gk + Qk) = 50 %
3Values of q
k,max apply to a centrally-loaded strip foundation, with minimal inclination of the load from the vertical. qk,max may be increased by 20% for a square or circular foundation
4B = breadth of foundation, d = depth to underside of foundation, dw = depth of groundwater
5Value may be increased by 5 % when G >> Q ; but should be reduced by 5 % when G << Q
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`

k k k k

55
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

A flow chart showing the design process for shallow foundations is Partial factors for the soil parameters used to determine the resistances
given in Figure 1. can be obtained from Table 3 above (Combination 2).

Where there is a moment applied to the foundation, the EQU limit The pressure distribution under the base should be assessed to ensure
state should also be checked. Assuming the potential overturning of that the maximum pressure does not exceed the bearing resistances
the base is due to the variable action from the wind, the following obtained from the geotechnical design report at both EQU and GEO
combination should be used (the variable imposed action is not ultimate limit states (see Figure 2). If the eccentricity is greater than
considered to contribute to the stability of the structure): L/6 at SLS, then the pressure distribution used to determine the
settlement should be modified because tension cannot occur between
0.9 Gk + 1.5 Qk,w EQU combination the base and the soil. In this case the designer should satisfy himself
where: that there will be no adverse consequences (e.g. excessive rotation of
Gk is the stabilising characteristic permanent action the base). It should also be noted that the ULS pressure distribution
(Use 1.1 Gk for a destabilising permanent action) diagram will be rectangular and not trapezoidal.
Qk,w is the destabilising characteristic variable wind action
Reinforced concrete pads
Figure 1
Procedures for depth of spread foundations Where the pad foundations require reinforcement the following checks
should be carried out to ensure:
■ Sufficient reinforcement to resist bending moments.
START
■ Punching shear strength.
■ Beam shear strength.
Obtain soil parameters from Ground Investigation report
The moments and shear forces should be assessed using the STR
combination:
1.35 Gk + 1.5 Qk STR combination 1 (Exp. (6.10))
Design using
Yes No
direct method?
However, there may be economies to made from using Expressions
(6.10a) or (6.10b) from the Eurocode.
Size foundation
Use prescriptive method.
(geotechnical design) using The critical bending moments for design of bottom reinforcement
Size foundation
the worst of Combinations
(geotechnical design) are located at the column faces. Both beam shear and punching
1 or 2 (ULS) for actions
using SLS for actions
and geotechnical material shear should then be checked at the locations shown in Figure 3. For
and presumed
properties. Combination 2
bearing resistance
will usually govern. punching shear the ground reaction within the perimeter may be
deducted from the column load (Expression (6.48), Eurocode 2–1–13).
It is not usual for a pad foundation to contain shear reinforcement,
therefore it is only necessary to ensure that the concrete shear stress
Check overturning using EQU
Is there an limit state for actions and capacity without shear reinforcement (vRd,c – see Table 6) is greater
overturning moment? GEO Combination 2
Yes than applied shear stress (vEd = VEd/(bd)).
for material properties.

No If the basic shear stress is exceeded, the designer may increase the
depth of the base. Alternatively, the amount of main reinforcement
Design foundation (structural design) using the worst of
Combinations 1 and 2 (ULS) for actions and geotechnical could be increased or, less desirably, shear links could be provided. (See
material properties.
Chapter 4, for an explanation of how to design shear reinforcement.)

Figure 2
Pressure distributions for pad foundations

M M M
P 6e
1
L L
P or P P

2P P
1.5 L 3 e L 2e
e e
P
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

P e = M/ P e
P 6e L = width of base P
1+
L L
SLS pressure distributions ULS pressure distribution

56
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
6. Foundations

Design for punching shear Figure 4

Procedure for determining punching shear capacity for pad foundations
Eurocode 2 provides specific guidance on the design of foundations for
punching shear, and this varies from that given for slabs. In Eurocode 2 the
shear perimeter has rounded corners and the forces directly resisted by START

the ground should be deducted (to avoid unnecessarily conservative

designs). The critical perimeter should be found iteratively, but it is Determine value of factor `
generally acceptable to check at d and 2d. Alternatively, a spreadsheet (` =1.0 when applied moment is zero; refer to Expressions
(6.38) to (6.42) from BS EN 1992–1–1 for other cases)
could be used (e.g. spreadsheet TCC81 from Spreadsheets for concrete
design to BS 8110 and Eurocode 2 4). The procedure for determining the
punching shear requirements is shown in Figure 4. Determine value of vEd,max
(design shear stress at face of column) from:
vEd,max = `(VEd – DVEd) (from Exp. (6.38))
Table 6 (u0deff)
vRd,c resistance of members without shear reinforcement, MPa
where u0 is perimeter of column
rl (see Clause 6.4.5 for columns at base edges)
Effective depth, d (mm)
deff = (dy + dz)/2 where dy and dz
300 400 500 600 700 800 900 1000a are the effective depths in orthogonal directions

0.25% 0.47 0.43 0.40 0.38 0.36 0.35 0.35 0.34

0.50% 0.54 0.51 0.48 0.47 0.45 0.44 0.44 0.43 Determine value of vRd,max (refer to Table 7)

0.75% 0.62 0.58 0.55 0.53 0.52 0.51 0.50 0.49

1.00% 0.68 0.64 0.61 0.59 0.57 0.56 0.55 0.54
No
1.25% 0.73 0.69 0.66 0.63 0.62 0.60 0.59 0.58 Is vEd,max < vRd,max? Redesign foundation

1.50% 0.78 0.73 0.70 0.67 0.65 0.64 0.63 0.62

Yes
1.75% 0.82 0.77 0.73 0.71 0.69 0.67 0.66 0.65
*2.00% 0.85 0.80 0.77 0.74 0.72 0.70 0.69 0.68
Determine value of vEd, (design shear stress) from:
k vEd = (VEd – D VEd)
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

1.816 1.707 1.632 1.577 1.535 1.500 1.471 1.447

(u1deff)
Key where u1 is length of control perimeter (refer to Figure 5). For
a For depths greater than 1000 calculate vRd,c directly. eccentrically loaded bases, refer to Exp. (6.51).
The control perimeter will have to be found through iteration;
Notes it will usually be between d and 2d
1 Table derived from: vRd,c = 0.12 k (100r I fck)(1/3) ≥ 0.035 k1.5 fck0.5
where k = 1 + 3(200/d) ≤ 2 and r I = 3(rIy +r Iz) ≤ 0.02,
r Iy = Asy/(bd) and r Iz = Asz/(bd)
Determine concrete punching shear capacity vRd (without
2 This table has been prepared for fck = 30; shear reinforcement) from 2dvRd,c/a (Refer to Table 6 for vRd,c)
where r l exceed 0.40% the following factors may be used: Where ‘a’ is the distance from the periphery of the column to
the control perimeter considered.
fck 25 28 32 35 40 45 50
Factor 0.94 0.98 1.02 1.05 1.10 1.14 1.19 Either increase main
steel, or provide
Is vEd < vRd at No punching shear
critical perimeter? reinforcement.
(Not recommended
Figure 3 for foundations.)
Yes
Shear checks for pad foundations
No shear reinforcement required. Check complete.

Beam shear Punching shear perimeters,

faces (load within deducted from V Ed)

Figure 5
Typical basic control perimeters around loaded areas

2d
u1

u1 2d
2d

Bends may be
d required

h d
by

57
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Raft foundations flexure reference should be made to Chapter 4.

Alternatively, a truss analogy may be used; this is covered in Sections 5.6.4

The basic design processes for rafts are similar to those for isolated and 6.5 of Eurocode 2–1–1. The strut angle y should be at least 21.8° to
pad foundations or pilecaps. The only difference in approach lies in the the horizontal; note that y should be measured in the plane of the column
selection of an appropriate method for analysing the interaction between and pile.
the raft and the ground so as to achieve a reasonable representation of
their behaviour. For stiffer rafts (i.e. span-to-thickness greater than 10) with Both beam shear and punching shear should then be checked as shown in
a fairly regular layout, simplified approaches such as yield line or the flat Figure 6. For beam shear, the design resistances in Table 6 may be used. If the
slab equivalent frame method may be employed, once an estimation of basic shear stress is exceeded, the designer should increase the depth of the
the variations in bearing pressure has been obtained from a geotechnical base. Alternatively, the amount of main reinforcement could be increased or,
specialist. Whatever simplifications are made, individual elastic raft less desirably, shear links could be provided. Care should be taken that main
reactions should equate to the applied column loads. bars are fully anchored. As a minimum, a full anchorage should be provided
from the inner face of piles. Large radius bends may be required.
Thinner, more flexible rafts or those with a complex layout may require
the application of a finite element or grillage analysis. For rafts bearing When assessing the shear capacity in a pile cap, only the tension steel
on granular sub-grades or when contiguous-piled walls or diaphragm placed within the stress zone should be considered as contributing to the
perimeter walls are present, the ground may be modelled as a series shear capacity (see Figure 7).
of Winkler springs. However, for cohesive sub-grades, this approach is
unlikely to be valid, and specialist software will be required.
Figure 6
Critical shear perimeters for piles

Piled foundations f /5 Beam shear 5 d from column face

For the purpose of this chapter it is assumed that the pile design will be
carried out by a specialist piling contractor. The actions on the piles must f /5
be clearly conveyed to the pile designer, and these should be broken down
into the unfactored permanent actions and each of the applicable variable
Punching shear 5 2d from column face
actions (e.g. imposed and wind actions). The pile designer can then carry
out the structural and geotechnical design of the piles. f

Where moments are applied to the pilecap the EQU combination

should also be used to check the piles can resist the overturning forces.
These EQU loads must also be clearly conveyed to the pile designer Figure 7
Shear reinforcement for pilecaps
and procedures put in place to ensure the piles are designed for the
correct forces.
A s contributing to shear capacity

A pilecap may be treated as a beam in bending, where the critical

bending moments for the design of the bottom reinforcement are Stress zone
o
located at the column faces. For further guidance on designing for 45

Table 7
Values for vRd, max

fck vRd,max Figure 8

20 3.68 Dimensions for plain foundations

25 4.50
28 4.97
a a
30 5.28
32 5.58
hF
35 6.02
40 6.72
bF
45 7.38
50 8.00

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

58
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
6. Foundations

Plain concrete foundations Table 8

Minimum percentage of reinforcement required

Strip and pad footings may be constructed from plain concrete fck fctm Minimum % (0.26 fctm /fyka )
provided the following rules are adhered to. 25 2.6 0.13%
■ In compression, the value of acc,pl, the coefficient taking account of 28 2.8 0.14%
long-term effects applied to design compressive strength 30 2.9 0.15%
(see Cl. 3.1.6), should be taken as 0.6 as opposed to 0.85 for 32 3.0 0.16%
reinforced concrete. 35 3.2 0.17%
■ The minimum foundation depth, hF, (see Figure 8) may be 40 3.5 0.18%
calculated from: 45 3.8 0.20%
50 4.1 0.21%
Key
a Where fyk = 500 MPa.

where:
sgd = the design value of the ground bearing pressure
fctd,pl = the design concrete tensile strength from Exp. (12.1) Selected symbols
a = is the projection from the column face Symbol Definition Value
Ac Cross sectional area of concrete bh

The possibility of splitting forces, as advised in Clause 9.8.4 of Eurocode As Area of tension steel
As, prov Area of tension steel provided
2–1–1, may need to be considered.
As, req Area of tension steel required
Eurocode 2 allows plain concrete foundations to contain reinforcement d Effective depth
for control of cracking. deff Average effective depth (dy + dz) /2
fcd Design value of concrete compressive strength acc fck /gc
fck Characteristic cylinder strength of concrete

Rules for spacing and fctm Mean value of axial tensile strength 0.30 fck2/3 for fck ≤ C50/60
(from Table 3.1, Eurocode 2)

quantity of reinforcement Gk
h
Characteristic value of permanent action
Overall depth of the section
leff Effective span of member See Section 5.3.2.2 (1)
Crack control M Design moment at the ULS
Refer to Chapter 2, originally published as Getting started 9. Qk Characteristic value of a variable action
Qk,w Characteristic value of a variable wind action
Minimum area of principal reinforcement VEd Design value of applied shear force

The minimum area of reinforcement is As,min = 0.26 fctm bt d/fyk but not vEd Design value of applied shear stress
VRd,c Design value of the punching shear
less than 0.0013bt d (see Table 8).
resistance without punching shear reinforcement
vRd,c Design value of the punching shear stress
Maximum area of reinforcement resistance without punching shear reinforcement --`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Except at lap locations, the maximum area of tension or compression vRd,max Design value of the maximum punching shear
resistance along the control section considered
reinforcement, should not exceed As,max = 0.04 Ac
x Depth to neutral axis (d – z)/0.4
xmax Limiting value for depth to neutral axis (d – 0.4)d where d ≤1.0
Minimum spacing of reinforcement
z Lever arm
The minimum spacing of bars should be the greater of:
acc Coefficient taking account of long term 0.85 for flexure and
■ Bar diameter, effects on compressive strength and of axial loads, 1.0 for
■ Aggregate size plus 5 mm, or unfavourable effects resulting from the way other phenomena
load is applied (From UK National Annex)
■ 20 mm.
b Factor for determining punching shear stress
d Ratio of the redistributed moment to the elastic
Deep elements bending moment
For deep elements the advice in Eurocode 2 for the side faces of deep gm Partial factor for material properties
beams may be followed. The UK National Annex recommends that 0.2% r0 Reference reinforcement ratio fck/1000

is provided in each face. The distance between bars should not exceed rl Required tension reinforcement at mid-span As l bd
to resist the moment due to the design
the lesser of twice the beam depth or 300 mm. For pile caps the side loads (or at support for cantilevers)
face may be unreinforced if there is no risk of tension developing. c0 Factor for combination value of a variable action
c1 Factor for frequent value of a variable action
c2 Factor for quasi-permanent value of a variable action

59
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
6. Foundations

References
1 BRITISH STANDARDS INSTITUTION. BS EN 1997: Eurocode 7: Geotechnical design. BSI (2 parts).
2 BRITISH STANDARDS INSTITUTION. BS 8004: Code of practice for foundations. BSI, 1986.
3 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–1, Eurocode 2: Design of concrete structures. General rules and rules for buildings. BSI, 2004.
4 GOODCHILD, C H & WEBSTER R M. Spreadsheets for concrete design to BS 8110 and Eurocode 2, version 3. The Concrete Centre, 2006.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

60
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

7. Flat slabs
R Moss BSc, PhD, DIC, CEng, MICE, MIStructE O Brooker BEng, CEng, MICE, MIStructE, MCS J Burridge MA CEng MIStructE MICE

Designing to Eurocode 2
This chapter covers the analysis and design of concrete flat slabs to Eurocode
21, which does not contain the derived formulae or specific guidance on
determining moments and shear forces. European practice is to give principles
in the codes and for the detailed application to be presented in other sources
such as textbooks.

It should be noted that values from the UK National Annex (NA) have been
used throughout this publication, including values that are embedded in
derived formulae (derivations can be found at www.concretecentre.com/
eurocode2). A list of symbols related to flat slab design is given at the end of
this chapter.

This chapter is a brief overview of the design of flat slabs. More in-depth
guidance on the provisions for the design of concrete flat slabs to Eurocode
2 can be found in The Concrete Society report TR64, Guide to the Design and
Construction of Reinforced Concrete Flat Slabs.2

Analysis
Using Eurocode 2 the following methods may be used:
■ Equivalent frame method
■ Finite element analysis

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
■ Yield line analysis
■ Grillage analogy

The Eurocode gives further advice on the equivalent frame method in

Annex I. Once the bending moments and shear forces have been determined,
the following guidance can be used for the design of flat slabs.

Design procedure
A procedure for carrying out the detailed design of flat slabs is shown in Table 1.
This assumes that the slab thickness has previously been determined during
conceptual design. More detailed advice on determining design life, loading,
material properties, methods of analysis, minimum concrete cover for
durability and bond, and control of crack widths can be found in Chapter 2.

Copyright The Concrete Centre

Fire resistance nominal (not minimum) dimension, so the designer should ensure that
cnom + f link + f main bar/2 ≥ amin, where amin is the minimum axis distance
from the fire tables.
Eurocode 2, Part 1–2: Structural fire design3, gives a choice of advanced,
simplified or tabular methods for determining the fire resistance. Using The requirements for flat slabs are given in Table 2.
tables is the fastest method for determining the minimum dimensions

Flexure
and cover for flat slabs. There are, however, some restrictions and if these
apply further guidance is given in Chapter 11.

Rather than giving a minimum cover, the tabular method is based The design procedure for flexural design is given in Figure 1; this
on nominal axis distance, a. This is the distance from the centre of includes derived formulae based on the simplified rectangular stress
the reinforcing bar to the surface of the member. Where there are block from Eurocode 2 Cl. 3.1.7 (3) (see Figure 2). Where appropriate
a number of bars providing resistance it can be considered to be a Table 3 may be used to determine bending moments for flat slabs.

Table 1
Flat slab design procedure

Step Task Further guidance

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
8 Analyse structure to obtain critical moments and shear forces 2: Getting started and Table 3 BS EN 1992–1–1 Section 5
9 Design flexural reinforcement See Figure 1 BS EN 1992–1–1 Section 6.1
10 Check deflection See Figure 3 BS EN 1992–1–1 Section 7.4
11 Check punching shear capacity See Figure 6 BS EN 1992–1–1 Section 6.4
12 Check spacing of bars 2: Getting started BS EN 1992–1–1 Section 7.3
13 Check resistance to moment transfer from column to slab – BS EN 1992–1–1 Annex I 1.2(5)
Note
NA = National Annex

Table 2
Minimum dimensions and axis distances for reinforced concrete slabs

Standard fire resistance Minimum dimensions (mm)

Slab thickness, hs Axis distance, a
REI 60 180 15a
REI 90 200 25
REI 120 200 35
REI 240 200 50
Notes
1 This table is taken from BS EN 1992–1–2 Table 5.9.
2 The axis distance is to the centre of the outer layer of reinforcement.
3 The table is valid only if the detailing requirements (see note 4) are observed and, in the normal temperature design, redistribution of bending moments does not exceed 15%.
4 For fire resistance of R90 and above, at least 20% of the total top reinforcement in each direction over intermediate supports required by BS EN 1992–1–1 should be continuous over
the full span. This reinforcement should be placed in the column strip.
5 There are three standard fire exposure conditions that may need to be satisfied:
R Mechanical resistance for load bearing
E Integrity of separation
I Insulation
Key
a Normally the requirements of BS EN 1992–1–1 will determine the cover.

62
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
7. Flat slabs

Figure 1 Whichever method of analysis is used, Cl. 9.4.1 requires the designer
Procedure for determining flexural reinforcement to concentrate the reinforcement over the columns. Annex I of the
Eurocode gives recommendations for the equivalent frame method on
START how to apportion the total bending moment across a bay width into
column and middle strips to comply with Cl. 9.4.1. Designers using
Carry out analysis of slab to determine design moments grillage, finite element or yield line methods may also choose to follow
(M) (Where appropriate use coefficients from Table 3).
the advice in Annex I to meet this requirement.

K’ has been determined using UK National Annex values in Eurocode 2

No Outside scope of Part 1-1 Exp (5.10a).
Concrete class
)C50/60? this publication
The Eurocode gives recommendations for the design of concrete up
Yes to class C90/105. However, for concrete strength greater than class
M
C50/60, the stress block is modified. It is important to note that
Determine KK from:
Determine from: K =
bd 2 fck concrete strength is based on the cylinder strength and not the cube
strength (i.e. for class C28/35 the cylinder strength is 28 MPa, whereas
Determine K’ from Table 4 or the cube strength is 35 MPa).
K’ = 0.60d – 0.18 d 2 – 0.21 where d ) 1.0
Table 4
Values for K’
Compression
No reinforcement % redistribution d (redistribution ratio) K’ x/d
Is K ) K ’ ? required – not
recommended for
0 1.00 0.208a 0.6
typical slabs 10 0.90 0.182a 0.5
Yes 15 0.85 0.168 0.45
20 0.80 0.153 0.4
No compression reinforcement required
25 0.75 0.137 0.35
30 0.70 0.120 0.3
Key
Obtain lever arm z from Table 5 or
a It is often recommended in the UK that K’ should be limited to 0.168 to ensure ductile
z=
d
2 [
1 + 1 – 3.53 K ) 0.95d ] failure.

Table 5
Calculate tension reinforcement required from z/d for singly reinforced rectangular sections
M
As =
fyd z K z/d K z/d
≤ 0.05 0.950a 0.13 0.868
0.06 0.944 0.14 0.856
Check minimum reinforcement requirements (see Table 6)
0.26 fctm bt d 0.07 0.934 0.15 0.843
As,min = where fyk * 25 0.08 0.924 0.16 0.830
fyk
0.09 0.913 0.17 0.816
0.10 0.902 0.18 0.802
Check maximum reinforcement requirements. 0.11 0.891 0.19 0.787
As,max = 0.04 Ac for tension or compression
reinforcement outside lap locations
0.12 0.880 0.20 0.771
Key
a Limiting z to 0.95d is not a requirement of Eurocode 2, but is considered to be good practice

Table 3 Table 6
Bending moment coefficients for flat slabs Minimum percentage of reinforcement required

End support/slab connection First Interior Interior fck fctm Minimum % (0.26 fctm /fyka )
interior spans supports 25 2.6 0.13%
Pinned Continuous support 28 2.8 0.14%
End End End End 30 2.9 0.15%
support span support span
32 3.0 0.16%
Moment 0 0.086Fl – 0.04Fl 0.075Fl –0.086Fl 0.063Fl – 0.063Fl 35 3.2 0.17%
Notes 40 3.5 0.18%
1 Applicable to slabs where the area of each bay exceeds 30 m2, 45 3.8 0.20%
Qk, ≤ 1.25 Gk and qk ≤ 5 kN/m2 50 4.1 0.21%
2 F is the total design ultimate load, l is the effective span Key
3 Minimum span > 0.85 longest span, minimum 3 spans a Where fyk = 500 MPa
4 Based on 20% redistribution at supports and no decrease in span moments

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

63
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Deflection depth ratios are appropriate where the structure remains propped
during construction or until the concrete attains sufficient strength to
support the construction loads
Eurocode 2 has two alternative methods of designing for deflection;
either by limiting span-to-depth ratio or by assessing the theoretical It should be noted that the UK National Annex recommends that ss is
deflection using the Expressions given in the Eurocode. The latter is calculated using characteristic values and not quasi-permanent values.
dealt with in detail in Chapter 8.

The span-to-depth ratios should ensure that deflection is limited

to span/250 and this is the procedure presented in Figure 3. The
Punching shear
Background paper to the UK National Annex 4 notes that the span-to- The design value of the punching shear force, VEd, will usually be the
support reaction at the ultimate limit state.

Figure 2 Eurocode 2
Simplified rectangular stress block for concrete up to class C50/60
■ Gives standard factors for edge and corner columns that allow for
from Eurocode 2
moment transfer (b). However, b can be calculated directly from
Expressions (6.38) to (6.46).

Figure 4
Basic span-to-effective-depth ratios for flat slabs

37 fck = 50
Figure 3 fck = 45
Procedure for assessing deflection 35 fck = 40
fck = 35
START 33 fck = 32
Span-to-effective-depth ratio (l/d)

fck = 30
31 fck = 28
Determine basic l/d from Figure 4 fck = 25
29 fck = 20

Determine Factor 1 (F1) For ribbed or waffle slabs 27

F1 = 1 – 0.1 ((bf/bw) – 1) * 0.8†
(bf is flange breadth and bw is rib breadth) 25
Otherwise F1 = 1.0
23

21
Determine Factor 2 (F2)
Where the slab span exceeds 8.5 m and it supports 19
brittle partitions, F2 = 8.5/leff Otherwise F2 = 1.0
17

15
0.40% 0.60% 0.80% 1.00% 1.20% 1.40% 1.60% 1.80% 2.00%
Determine Factor 3 (F3)
Percentage of tension reinforcement (A s ,req /bd)
F3 = As,prov/As,req ) 1.5 or 310/ss ) 1.5 (UK NA)
where ss is the stress in the reinforcement calculated
under the characteristic combination of SLS loads.
Notes
See Figure 5
Increase
1 This graph assumes a simply supported flat slab (K = 1.2).
As,prov
2 Compression reinforcement, r’, has been taken as 0.

Is basic l/d x F1 x F2 x F3 * Actual l/d ? 3 Curves based on the following expressions:

[ ( ) ]
r0 1.5
l 1.5 fck r 0 fck
Yes = K 11 +
r
+ 3.2
r
–1 where r ≤ r 0 and
d
Check complete

† The Eurocode is ambiguous regarding linear interpolation. It is understood that this

was the intention of the drafting committee and is in line with current UK practice.
l
d [
= K 11 +
1.5 fck r 0
( r – r ’)
+
fck
12 ]
r’
r0
where r > r 0 .

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

64
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
7. Flat slabs

■ The UK NA recommends VEd ≤ 2VRd,c at the basic control perimeter. As an alternative to using shear links, proprietary shear stud rails
■ Gives an Expression for the maximum value of shear at the column
may be used. Eurocode 2 (Figure 6.22) allows them to be laid out
face, and it depends on the concrete strength used (see Table 7). in a radial or cruciform pattern and gives spacing requirements for
both. Other techniques are available for increasing punching shear
■ Has rounded corners for the control perimeters for rectangular
resistance and these are covered in a best practice guide5.
columns (see Figure 8).
■ Enables the point at which no shear reinforcement is required to be Figure 6
calculated directly and then used to determine the extent of the Procedure for determining punching shear capacity
area over which shear reinforcement is required.
■ Assumes that the reinforcement will be in a radial arrangement. START

However, the reinforcement can be laid on a grid provided the

Determine value of factor `
spacing rules are followed. (refer to Figure 7 or Expressions (6.38) to (6.46)
of the Eurocode)
The procedure for determining the punching shear requirements is
shown in Figure 6.
Determine value of vEd
(design shear stress at face of column) from:
vEd = ` VEd /(ui deff)
where ui is perimeter of column
deff = (dy + dz)/2 (dy and dz
are the effective depths in orthogonal directions)

Determine value of vRd,max from Table 7

Figure 5
Determination of approximate steel stress at SLS
No
Is vEd,≤ vRd,max? Redesign slab

Yes

Determine value of vEd, (design shear stress) from:

vEd = ` VEd /(u1 deff)
where u1 is length of control perimeter (see Figure 8)

Determine concrete punching shear capacity

(without shear reinforcement), vRd,c from Table 8
where r l = (r ly r lz)0.5
(r ly, r lz are the reinforcement ratios in two orthogonal
directions for fully bonded tension steel, taken over a
width equal to column width plus 3d each side.)

No Punching shear
Is vEd > vRd,c? reinforcement not
required

Yes

ξ
No
Is vEd ≤ 2vRd,c Redesign slab
To determine stress in the reinforcement (σs), calculate the ratio Gk/Qk,
read up the graph to the appropriate curve and read across to determine
σsu. σs can be calculated from the expression: σs = σsu (As,req/As,prov) ( 1/δ)
Yes

Determine area of punching shear reinforcement per perimeter

from:
Asw = (vEd – 0.75vRd,c)sr u1/(1.5 fywd,ef)
where
sr is the radial spacing of shear reinforcement (see Figure 9)
fywd,ef = 250 + 0.25 deff ) fywd (see Table 9)
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Determine the length of the outer perimeter where shear

reinforcement not required from:
uout,ef = b VEd/(vRd,c d)

Determine layout of punching shear reinforcement

(see ‘Spacing of punching shear reinforcement’
Section and Figure 9).

65
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Table 7 Table 9 Figure 7

Values for vRd,max Values for fywd,ef Recommended standard values for b
fck vRd, max deff fywd,ef
20 3.68 150 288 Corner column
25 4.50 175 294
b = 1.5
28 4.98 200 300
30 5.28 225 306
32 5.58 250 313
35 6.02 275 319 Edge column Internal column
40 6.72 300 325
45 7.38 325 331 b = 1.4 b = 1.15

50 8.00 350 338

Rules for spacing and

Table 8
vRd,c resistance of members without shear reinforcement, MPa
rI
quantity of reinforcement
Effective depth, d (mm)

)200 225 250 275 300 350 400 450 500 600 750
0.25% 0.54 0.52 0.50 0.48 0.47 0.45 0.43 0.41 0.40 0.38 0.36
0.50% 0.59 0.57 0.56 0.55 0.54 0.52 0.51 0.49 0.48 0.47 0.45 Minimum area of reinforcement
0.75% 0.68 0.66 0.64 0.63 0.62 0.59 0.58 0.56 0.55 0.53 0.51 The minimum area of longitudinal reinforcement in the main direction
1.00% 0.75 0.72 0.71 0.69 0.68 0.65 0.64 0.62 0.61 0.59 0.57 is As,min = 0.26 fctm bt d/fyk but not less than 0.0013b d (see Table 6).
1.25% 0.80 0.78 0.76 0.74 0.73 0.71 0.69 0.67 0.66 0.63 0.61
The minimum area of a link leg for vertical punching shear
1.50% 0.85 0.83 0.81 0.79 0.78 0.75 0.73 0.71 0.70 0.67 0.65
reinforcement is
1.75% 0.90 0.87 0.85 0.83 0.82 0.79 0.77 0.75 0.73 0.71 0.68
1.5Asw,min /(sr.st) ≥ 0.08fck½/fyk
* 2.00% 0.94 0.91 0.89 0.87 0.85 0.82 0.80 0.78 0.77 0.74 0.71
which can be rearranged as
k 2.000 1.943 1.894 1.853 1.816 1.756 1.707 1.667 1.632 1.577 1.516
Asw,min ≥ (sr.st)/F
Notes
1 Table derived from: v Rd,c = 0.12 k (100r I fck)1/3 ≥ 0.035 k1.5 fck 0.5 where where
k = 1 + R(200/d) ≤ 2 and r I = R(r ly x r lz) ≤ 0.02, r ly = Asy/(bd) and r lz = Asz/(bd)
sr = the spacing of the links in the radial direction
2 This table has been prepared for fck = 30;
Where r I exceeds 0.40% the following factors may be used: st = the spacing of the links in the tangential direction
fck 25 28 32 35 40 45 50 F can be obtained from Table 10
Factor 0.94 0.98 1.02 1.05 1.10 1.14 1.19
Maximum area of reinforcement
Outside lap locations, the maximum area of tension or compression
reinforcement should not exceed As,max = 0.4 Ac

Figure 8
Typical basic control perimeters around loaded areas
Minimum spacing of reinforcement
The minimum spacing of bars should be the greater of:
■ Bar diameter
u1
■ Aggregate size plus 5 mm
u1 2d
2d ■ 20 mm

bz Maximum spacing of main reinforcement

For slabs less than 200 mm thick the following maximum spacing rules apply:
■ For the principal reinforcement: 3h but not more than 400 mm
■ For the secondary reinforcement: 3.5h but not more than 450 mm
by
The exception is in areas with concentrated loads or areas of maximum

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
66
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
7. Flat slabs

moment where the following applies: Table 10

■ For the principal reinforcement: 2h but not more than 250 mm Factor, F, for determining Asw, min

■ For the secondary reinforcement: 3h but not more than 400 mm fck Factor, F
Where h is the depth of the slab. 25 1875
28 1772
For slabs 200 mm thick or greater, the bar size and spacing should be
30 1712
limited to control the crack width and reference should be made to
32 1657
Section 7.3.3 of the Eurocode or Chapter 2.
35 1585
40 1482
Spacing of punching shear reinforcement
45 1398
Where punching shear reinforcement is required the following rules
50 1326
should be observed.
Note
■ It should be provided between the face of the column and kd
fyk has been taken as 500 MPa
inside the outer perimeter where shear reinforcement is no longer
required. k is 1.5, unless the perimeter at which reinforcement is no
longer required is less than 3d from the face of the column. In this Selected symbols
case the reinforcement should be placed in the zone 0.3d to 1.5d Symbol Definition Value
from the face of the column. Ac Cross sectional area of concrete bh
■ There should be at least two perimeters of shear links.
As Area of tension steel
■ The radial spacing of the links should not exceed 0.75d
As2 Area of compression steel
(see Figure 9).
As, prov Area of tension steel provided
■ The tangential spacing of the links should not exceed 1.5d within
2d of the column face. As, req Area of tension steel required

■ The tangential spacing of the links should not exceed 2d for any b Width of slab
other perimeter. d Effective depth
■ The distance between the face of the column and the nearest shear
d2 Effective depth to compression reinforcement
reinforcement should be between 0.3d and 0.5d.
fcd Design value of concrete compressive strength acc fck /gc

fck Characteristic cylinder strength of concrete

fctm Mean value of axial tensile strength 0.30 fck2/3 for fck ≤ C50/60
(from Table 3.1, Eurocode 2)
Figure 9
Punching shear layout hs Slab thickness

K Factor to take account of the different See Table NA5 in

structural systems UK National Annex
Outer perimeter of
shear reinforcement Outer control leff Effective span of member See Section 5.3.2.2 (1)
perimeter
u out l/d Limiting span-to-depth ratio

M Design moment at the ULS

x Depth to neutral axis (d – z)/0.4

≤ 0.75d
A xmax Limiting value for depth to neutral axis (d – 0.4)d where d ≤1.0
A ≤1.5d
z Lever arm
≤ 1.5d
sr (2d if > 2d a cc Coefficient taking account of long term 0.85 for flexure and
from column) effects on compressive strength and of axial loads.
st
unfavourable effects resulting from the 1.0 for other phenomena
way load is applied (From UK National Annex)

d Ratio of the redistributed moment to the

elastic bending moment
0.3d ≤ si ≤ 0.5d gm
s r ≤ 0.75 d Partial factor for material properties 1.15 for reinforcement (gs )
1.5 for concrete (gc )

kd r0 Reference reinforcement ratio 10-3Rfck

r Required tension reinforcement at mid-span As/bd

to resist the moment due to the design
loads (or at support for cantilevers)
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Outer control
perimeter r’ Required compression reinforcement at As2/bd
mid-span to resist the moment due to the
Section A - A
design loads (or at support for cantilevers)

67
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
7. Flat slabs

References
1 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–1, Eurocode 2: Design of concrete structures – General rules and rules for buildings. BSI, 2004.
2 THE CONCRETE SOCIETY, Technical Report 64 – Guide to the Design and Construction of Reinforced Concrete Flat Slabs. The Concrete Society, 2007.
3 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–2, Eurocode 2: Design of concrete structures. General rules – structural fire design. BSI, 2004.
4 BRITISH STANDARDS INSTITUTION. PD 6687–1, Background paper to the UK National Annex to BS EN 1992–1–1 and BS EN 1992–1–2. BSI, 2010.
5 BRITISH CEMENT ASSOCIATION. Prefabricated punching shear reinforcement for reinforced concrete flat slabs. BCA, 2001.
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

68
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

8. Deflection calculations

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
R Webster CEng, FIStructE O Brooker BEng, CEng, MICE, MIStructE, MCS J Burridge MA CEng MIStructE MICE

Methods for checking deflection

This chapter describes the use of Eurocode 21 to check deflection by
calculation. The alternative method for complying with the code requirements
is to use the deemed-to-satisfy span-to-effective-depth ratios, which are
appropriate and economic for the vast majority of designs. Further guidance
on the span-to-effective-depth method is given in Chapters 3, 4 and 7.
However, there are situations where direct calculation of deflection is
necessary, as listed below:
■ When an estimate of the deflection is required.
■ When deflection limits of span/250 for quasi-permanent actions (see
Chapter 1 for Eurocode terminology) or span/500 for partition and/or
cladding loads are not appropriate.
■ When the design requires a particularly shallow member, direct calculation
of deflection may provide a more economic solution.
■ To determine the effect on deflection of early striking of formwork or of
temporary loading during construction.

Overview
In the past structures tended to be stiff with relatively short spans. As
technology and practice have advanced, more flexible structures have resulted.
There are a number of reasons for this, including:
■ The increase in reinforcement strength leading to less reinforcement being
required for the ultimate limit state (ULS) and resulting in higher service
stresses in the reinforcement.
■ Increases in concrete strength resulting from the need to improve both
durability and construction time, and leading to concrete that is more stiff
and with higher service stresses.

What affects deflection?

There are numerous factors Other factors include:
that affect deflection. These • Degree of restraint
factors are also often time- • Magnitude of loading
related and interdependent, • Time of loading
which makes the prediction • Duration of loading
of deflection difficult. • Cracking of the concrete
• Shrinkage
The main factors are:
• Ambient conditions
• Concrete tensile strength
• Secondary load-paths
• Creep
• Stiffening by other elements
• Elastic modulus

Copyright The Concrete Centre

■ A greater understanding of structural behaviour and the ability to It is often recommended that the design value of the concrete
analyse that behaviour quickly by computer. tensile strength for a low restraint layout is taken as the average
■ The requirement to produce economic designs for slabs whose of fctm,fl and fctm, to allow for unintentional restraint. For high restraint
thicknesses are typically determined by the serviceability limit state fctm should be used.
(SLS) and which constitute 80% to 90% of the superstructure costs.
■ Client requirements for longer spans and greater operational Creep
flexibility from their structures. Creep is the time-dependant increase in compressive strain in a
concrete element under constant compressive stress. Creep is usually

Factors affecting deflection

considered in the design by modifying the elastic modulus using a
creep coefficient, h, which depends on the age at loading, size of
the member and ambient conditions, in particular relative humidity.
An accurate assessment of deflection can only be achieved if Eurocode 2 gives advice on the calculation of creep coefficients in
consideration is given to the factors that affect it. The more important detail in Annex B. It also advises on the appropriate relative humidity
factors are discussed in detail below. to use in Figure 3.1.

Tensile strength The cement strength class is required in the assessment of creep,
The tensile strength of concrete is an important property because the however, at the design stage it is often not clear which class should
slab will crack when the tensile stress in the extreme fibre is exceeded. be used. Generally, Class R should be assumed. Where the ground
In Eurocode 2 the concrete tensile strength, fctm, is a mean value granulated blastfurnace slag (ggbs) content exceeds 35% of the
(which is appropriate for deflection calculations) and increases as the cement combination or where fly ash (fa) exceeds 20% of the cement
compressive strength increases. combination, Class N may be assumed. Where ggbs exceeds 65% or
where fa exceeds 35% Class S may be assumed.
The degree of restraint to shrinkage movements will influence the
effective tensile strength of the concrete. A layout of walls with high Elastic modulus
restraint will decrease the effective tensile strength. Typical examples The elastic modulus of concrete is influenced by aggregate type,
of wall layouts are given in Figure 1. For a low restraint layout the workmanship and curing conditions. The effective elastic modulus
following expression may be used for the concrete tensile strength: under sustained loading will be reduced over time due to the effect
fctm,fl = (1.6 – h/1000)fctm > fctm of creep. These factors mean that some judgement is required
where to determine an appropriate elastic modulus. Eurocode 2 gives
fctm,fl = Mean flexural tensile strength of reinforced concrete recommended values for the 28-day secant modulus, Ecm, (in Table 3.1)
fctm = Mean tensile strength of concrete and makes recommendations for adjustments to these values to
account for different types of aggregate. The long-term elastic modulus
should be taken as:

Figure 1
Typical floor layouts

a) Favourable layout of restraining walls (low restraint)

b) Unfavourable layout of restraining walls (high restraint)

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

70
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
8. Deflection calculations

Ec,LT = Ec28/(1 + h) Commercial pressures often lead to a requirement to strike the formwork
where as soon as possible and move on to subsequent floors, with the minimum
Ec28 = 28-day tangent modulus = 1.05 Ecm of propping. Tests on flat slabs have demonstrated that as much as 70%
h = Creep factor. (Note that with Eurocode 2, h relates to a 28-day of the loads from a newly cast floor (formwork, wet concrete, construction
short-term elastic modulus, whereas a ‘true’ creep factor would loads) may be carried by the suspended floor below2. It can generally
be associated with the modulus at the age of loading.) be assumed that early striking of formwork will not greatly affect the
deflection after installing the cladding and/or partitions. This is because the
The assessment of the long-term E-value can be carried out more deflection affecting partitions will be smaller if the slab becomes ‘cracked’
accurately after the contractor has been appointed because they should be before, rather than after, the installation of the cladding and/or partitions.
able to identify the concrete supplier (and hence the type of aggregates)
and also the construction sequence (and hence the age at first loading). Cracking
Deflection of concrete sections is closely linked to the extent of
Loading sequence cracking and the degree to which cracking capacity is exceeded. The
The loading sequence and timing may be critical in determining point at which cracking occurs is determined by the moments induced
the deflection of a suspended slab because it will influence the point in the slab and the tensile strength of the concrete, which increases
at which the slab will crack (if at all) and is used to calculate the creep with age. Often the critical situation is when the slab is struck, or when
factors for the slab. A loading sequence is shown in Figure 2, which the load of the slab above is applied. Once the slab has cracked its
shows that in the early stages relatively high loads are imposed while stiffness is permanently reduced.
casting the slab above. The loading sequence may vary, depending on
the construction method. It is therefore necessary to find the critical loading stage at which
cracking first occurs. This critical loading stage corresponds with the
Smaller loads are imposed when further slabs are cast above. The loads minimum value of K, where:
are then increased permanently by the application of the floor finishes
K = fctm ^W 0.5h
and erection of the partitions. Finally, the variable actions are applied
to the structure and, for the purpose of deflection calculation, the
quasi-permanent combination should be used. (See Chapter 1, where
for further information on combinations of actions.) However, it is W = The serviceability loading applied up to that stage
likely that the quasi-permanent combination will be exceeded during fctm = The concrete tensile strength at that stage
the lifetime of the building and, for the purpose of determining Where the frequent combination is the critical load stage, then
whether the slab might have cracked, the frequent combination may the degree of cracking (z) calculated for the frequent combination
be critical. should also be used for the quasi-permanent combination, but not for

Figure 2
Loading history for a slab – an example

h
12
b g

10 f
c
e
8 d
a
Load (kN/m)

6 Loading sequence
a Slab struck e Floor finishes applied
4 b 1st slab above cast f Partitions erected
c 2nd slab above cast g Quasi-permanent variable actions
2 d 3rd slab above cast h Frequent variable actions

0
0 50 100 150 200 250 300
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Duration (days)

71
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

any of the earlier load stages. If, however, an earlier stage Figure 3
proves critical, the z value at that stage should be carried Outline of rigorous method for calculating deflection
forward to all subsequent stages.
Collate input data
Further information can be found in the best practice ■ Element dimensions and reinforcement details and arrangements from the
guide Early striking and improved backpropping3. ultimate limit state design
■ Loading sequence e.g.
• Striking the formwork
Shrinkage curvature • Casting the floor above
Shrinkage depends on the water/cement ratio, relative • Erection of the partitions and/or cladding
• Application of finishes
humidity and the size and shape of the member. The effect The sequence will vary from project to project
of shrinkage in an asymmetrically reinforced section is to ■ Concrete properties (see Table 1)
induce a curvature that can lead to significant deflection in • Mean compressive strength (fcm)
shallow members. This effect should be considered in the • Mean tensile strength (fctm or fctm,fl)
• Elastic modulus (Ec28) = 1.05 Ecm
deflection calculations.
■ Critical arrangement of actions
(or repeat the calculations for each arrangement to determine the critical case)

Methods for
Assess whether the element has flexural cracking
calculating deflections ■ Determine the critical load stage at which cracking first occurs.
(See ‘Cracking’ on page 71)
Two methods for calculating deflection are presented ■ Calculate the following properties:
• Creep coefficients, h (Annex B of Eurocode 2 or Figure 4)
below, and these are based on the advice in TR58 • Long term elastic modulus, ELT (see Panel 1)
Deflections in concrete slabs and beams4. • Effective modulus ratio, ae from: ae = Es /ELT
• Neutral axis depth for uncracked condition, xu (see Panel 2)
• Second moment of area for uncracked condition, Iu (see Panel 2)
Rigorous method • Calculate cracking moment, Mcr from:
Mcr = fctm Iu/(h – xu), using appropriate value for fctm.
The rigorous method for calculating deflections is the
■ Does the moment at the critical load stage exceed the cracking moment?
most appropriate method for determining a realistic
• If yes, the element is cracked at all subsequent stages.
estimate of deflection. However, it is only suitable for z = 1 – 0.5(Mcr/M)2 [z = 0 for uncracked situation]
Repeat at 1/20 points for all three loading stages

use with computer software. The Concrete Centre has Use these critical values of fctm and z for subsequent stages.
• If no, the element will not crack at any stage.
produced a number of spreadsheets that use this method
to carry out deflection calculations for a variety of slabs
and beams5. These offer a cost-effective way to carry
Determine the curvature of the slab
out detailed deflection calculations, and they include the
■ When the slab is cracked calculate the following properties at the load stage
ability to consider the effect of early age loading of the being considered, using appropriate values for fctm, z and ELT:
concrete. Figure 3 illustrates the principles of the method • Neutral axis depth for cracked section, xc (see Panel 2)
and shows how the factors affecting deflection are • Second moment of area for cracked condition, Ic (see Panel 2)
considered in the rigorous deflection calculations. ■ Calculate the flexural curvature:
1 MQP MQP
rfl = g E e Ic + ]1 – g g E e Iu
Finite element analysis may also be used to obtain
■ Calculate the curvature due to shrinkage strain 1/rcs (see Panel 2)
estimates of deflection. In this case the principles
■ Calculate the total curvature, 1/rt = 1/rfl + 1/rcs
in Figure 3 should be applied if credible results are to
be obtained.
Repeat the calculations at frequent intervals (say at 1/20 points) and integrate
Panel 1 twice to obtain the overall deflection.
Determining long term elastic modulus of elasticity

Calculate long-term elastic modulus, ELT from: If deflection affecting cladding and/or partitions is required, repeat calculations
for frequent combination and for loading at time of installation of partitions
W1 W2 W3 W4 W5
E LT = RW c + + + + m and/or cladding.
Eeff,1 Eeff, 2 Eeff, 3 Eeff, 4 Eeff, 5
where
Eeff = Ec28/(1+h) Estimate deflections:
■ Overall deflection (quasi-permanent combination)
Wn = Serviceability load at stage n
■ Deflection affecting partitions/cladding (Frequent combination deflection
h = Creep coefficient at relevant loading time
less deflection at time of installation)
and duration

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

72
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
8. Deflection calculations

Table 1
Concrete properties

fck MPa 320 325 328 330 332 335 340 350
fcm = (fck + 8) MPa 328 333 336 338 340 343 348 358
fctm = (0.3 fck(2/3) ≤ C50/60 or 2.12 ln(1 + (fcm/10)) > C50/60) MPa 332.21 332.56 332.77 332.90 333.02 333.21 333.51 334.07
fctm* = (0.3 fcm (2/3) ≤ C50/60 or 1.08 ln(fcm) + 0.1 > C50/60)a MPa 332.77 333.09 333.27 333.39 333.51 333.68 333.96 334.50
Ecm 0.3
= (22 [(fcm)/10] GPa 330.0 331.5 332.3 332.8 333.3 334.1 335.2 337.3
Ec28 = (1.05 Ecm) GPa 331.5 333.0 333.9 334.5 335.0 335.8 337.0 339.1
ecd,0 CEM class R, RH = 50% microstrain 746 706 683 668 653 632 598 536
ecd,0 CEM class R, RH = 80% microstrain 416 394 381 372 364 353 334 299
ecd,0 CEM class N, RH = 50% microstrain 544 512 494 482 471 454 428 379
ecd,0 CEM class N, RH = 80% microstrain 303 286 275 269 263 253 239 212
ecd,0 CEM class S, RH = 50% microstrain 441 413 397 387 377 363 340 298
ecd,0 CEM class S, RH = 80% microstrain 246 230 221 216 210 202 189 166
eca(') microstrain 325 338 345 350 355 363 375 100
Key
a fctm* may be used when striking at less than 7 days or where construction overload is taken into account.

Panel 2
Useful Expressions for a rectangular section

bh 2 where
2 + ] ae - 1 g ] Asd + As2 d2 g
xu = As = Area of tension reinforcement
bh + ] ae - 1 g ] As + As2 g
As2 = Area of compression reinforcement
bh 3 h 2 b = Breadth of section
I u = 12 + bh a 2 - xuk + ] ae - 1 g 6 As ]d - xu g + As2 ] x u - d 2 g @
2 2

d = Effective depth to tension

reinforcement

xc = # 7 ^ As ae + A s2 ] ae - 1 g h 2+ 2 b ^ As d ae + A s2d2 ] ae - 1 g h A 0.5- ^ As ae + As2 ] ae - 1 g h - b

d2 = Depth to compression reinforcement
h = Overall depth of section
bx c3 ae = Modular ratio
I c = 3 + ae As ^ d - x c g + ^ ae - 1 g As2 ^ d2 - x c g
2 2

Su = As(d – xu) – As2 (xu – d2)

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
1 SSuc SSuc Sc = As(d – xc) – As2 (xc – d2)
rcs = g f cs a e IIcu +^1 - g h fcs ae IIuc

Figure 4
Method for determining creep coefficient h(',t0)

1 1
S N R S N R
2 2
3 3
5 5

t 0 10 t 0 10

20 20
30 30
50 50

100 100
7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 100 300 500 700 900 1100 1300 6.0 5.0 4.0 3.0 2.0 1.0 0 100 300 500 700 900 1100 1300
h (?, t 0 ) h 0 (mm) h (?, t 0) h o (mm)
a) Inside conditions - RH = 50% b) Outside conditions - RH = 80%
How to use Nonogram
Key Notes
C20/25 C40/50 1 t0 = age of concrete at time of loading
D
C25/30 C45/55 2 h0 = 2A c /u A
C30/37 C50/60 3 Intersection point between lines D & E can also be above point A E C
B
C35/45 4 For t0 > 100 it is sufficiently accurate to assume t = 100

73
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Simplified method Figure 5

Simplified method for calculating deflection
A simplified method for calculating deflection is presented in Figure 5.
It is feasible to carry out these calculations by hand, and they could be
START
used to roughly verify deflection results from computer software, or
used where a computer is not available. Calculate the moment, MQP, due to quasi-permanent actions at
the critical section (i.e. mid-span or at support for cantilever)
The major simplification is that the effects of early age loading are not Obtain concrete properties, fctm, and Ec28 from Table 1
considered explicitly; rather an allowance is made for their effect when
calculating the cracking moment. Simplified creep factors are used and Calculate creep coefficient, h(',t0), using either Figure 4
or Annex B (in which case look-up fcm in Table 1)
deflection from the curvature of the slab is approximated using a factor.
1 Calculate long term elastic modulus, Eeff from: Eeff = Ec28/[1+h (',t0)]
Figure 6 2 Calculate effective modulus ratio, ae from ae = Es/Eeff, where Es is
elastic modulus for reinforcement (200 GPa)
Values for K for various bending moment diagrams
3 Calculate depth to neutral axis for uncracked condition, xu
4 Calculate second moment of area for uncracked condition, Iu
Loading Bending moment diagram K
0.9 fctm I u
0.125 Calculate cracking moment, Mcr from: Mcr =
M h – xu
M M (Note the factor 0.9 has been introduced into this method
because the loading sequence is not considered)

al W 3 4a 2 Yes No
48 (1-a)
Is Mcr > MQP?
l M = Wa (1-a ) l If a = 1 , K = 1
2 12
Section is uncracked Section is cracked
0.0625 z=0 z = 1 – 0.5(Mcr/MQP)2

M Calculate depth to neutral axis for cracked

condition, xc and calculate second moment of area
for cracked condition, Ic
W/2 W/2
a2
al al 0.125
6
Wal 1 MQP MQP
M= Calculate flexural curvature
rn
= g
Eeff Ic
+ ^1 – g h E
2 eff Iu

q 0.104 Calculate total shrinkage strain ecs from ecs = ecd + eca where:
ecd = kh ecd,0 = Drying shrinkage strain
ql 2 kh = Coefficient based on notional size, see Table 2
8 ecd,0 = Nominal unrestrained drying shrinkage, see Table 1
eca = bas(t) eca(') = eca(') for long-term deflection, see Table 1

q 0.102
Calculate curvature due to shrinkage strain 1/rcs (see Panel 2)
ql 2

15.6
1 1 1
Calculate total curvature r = rn + rcs
t,QP
b
q MA MC MB K = 0.104 (1 )
10 1
MA + MB Calculate quasi-permanent deflection from dQP KL 2 rt,QP =
b=
MC where K can be obtained from Figure 6 and L is the span.

al W End deflection
Wal
a (3 a ) Do you need No
= to calculate deflection
6 Finish
load at end K = 0.333 due to cladding and
partitions?
Yes
2 2
al qa l a (4 a )
q 2 12 Calculate the deflection that will occur at the time of application of
the load due to partitions and/or cladding.
if a = l , K = 0.25
1 Calculate the creep coefficient h(t,t0), where t is the age when
partition/cladding loads are applied and t0 is the age of striking.
b h(t,t0) 5 h(',t0) bc(t,t0). For bc(t,t0) refer to Figure 7, alternatively
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

MA MB K = 0.083 (1 ) refer to Annex B of Eurocode 2.

4
MA + MB 2 Calculate the moment due to self-weight, partitions/cladding and any
MC b= other loads which have been applied prior to the installation of the
MC
cladding/partition, Mpar and use in place of MQP
al al 3 Recalculate the section properties, curvature and hence deflection,
1 (5 4a 2 )
2 dpar, using h(t,t0) or equivalent instead of h(',t0)
2
Wl (3 4a 2) 80 3 4a 4 The approximate deflection affecting cladding and partitions is
24 d = dQP – dpar

74
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
8. Deflection calculations

Table 2
Values for Kh Precamber
h0 kh A slab or beam can be precambered to reduce the effect of deflection
>100 1.0 below the horizontal (see Figure 8). However, in practice too much
>200 0.85 precamber is generally used and the slab remains permanently
>300 0.75 cambered. This is because of the difficulty in accurately calculating
deflection. A precamber of up to half the quasi-permanent
>500 0.70
combination deflection could be used, but a lower figure is
Notes
h0 is the notional size (mm) of the cross-section = 2Ac/u
recommended. Precamber does not reduce the deflections affecting
where partitions or cladding.
Ac = Concrete cross-sectional area

Flat slabs
u = Perimeter of that part of the cross section which is exposed to drying

Figure 7
Coefficient for development of creep with time after loading Flat slabs are very popular and efficient floor systems. However,
because they span in two directions, it can be difficult to calculate their
0.60 deflection. TR58 4 gives several suitable methods for assessing flat slab
deflection. Of these, a popular method is to take the average deflection
of two parallel column strips and to add the deflection of the middle
0.55
strip spanning orthogonally to get an approximation of the maximum
deflection in the centre of the slab.
0.50
The recommended acceptance criteria for a flat slab are shown in Figure 9.
Coefficient, bc (t, t0)

Accuracy
0.45

0.40 The calculation of deflection in Eurocode 2 using the rigorous method

presented can be used to take account of early-age construction
0.35 loading by considering reduced early concrete tensile strengths.

However, the following influences on deflections cannot be accurately

0.30 assessed:
■ Tensile strength, which determines the cracking moment.
0.25
100 300 500 700 900 ■ Construction loading.
h 0 (mm)
■ Elastic modulus.

t = 90, t0 = 3 t = 90, t0 = 7 Therefore any calculation of deflection is only an estimate, and even the
t = 60, t0 = 3 t = 60, t0 = 7 most sophisticated analysis can still result in +15% to -30% error. It is
t = 28, t0 = 3 t = 28, t0 = 7 advisable to give a suitable caveat with any estimate of deflection that
Notes others are relying on.
t = Age of concrete when partitions/cladding applied
t0 = Age of concrete when struck
fck = 30 (fcm = 38), however the coefficient is not particularly sensitive to concrete class

Figure 8 Figure 9
Precambering of slabs Recommended acceptance criteria for flat slabs

Just before installation

Precamber of partitions Notes
If maximum permitted d = L/n and
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

X is the position of maximum d

where
a L = Span
X n = Limiting span-to-depth ratio,
e.g. 250
then the deflection at X should not be
Deflection due to greater than 2a/n.
Deflection due to frequent combination
quasi-permanent (Maximum deflection on gridlines
may be more critical.)
combination Deflection affecting partitions

75
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
8. Deflection calculations

Cladding tolerances ■ Manufacturers may say that their glazed systems can only
accommodate deflection as low as 5 mm.
Deflection may affect cladding or glazing in the following ways: There should be open discussions between the designers for the various
■ When a slab deflects, the load on the central fixings will be relieved elements to determine the most cost-effective way of dealing with the
and shed to outer fixings. interaction of the structure and cladding.

References
1 BRITISH STANDARDS INSTITUTION. BS EN 1992–1–1, Eurocode 2: Design of concrete structures. General rules and rules for building. BSI, 2004.
2 PALLETT, P. Guide to flat slab formwork and falsework. Construct, 2003
3 BRITISH CEMENT ASSOCIATION. Early striking and improved backpropping. BCA, 2001. (Available from www.concretecentre.com)
4 THE CONCRETE SOCIETY. Technical report No. 58 Deflections in concrete slabs and beams. The Concrete Society, 2005.
5 GOODCHILD, C H & WEBSTER, R M. Spreadsheets for concrete design to BS 8110 and EC2, version 3. The Concrete Centre, 2006.

76 --`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Copyright The Concrete Centre

9. Retaining walls
A J Bond MA, MSc, PhD, DIC, MICE, CEng O Brooker BEng, CEng, MICE, MIStructE, MCS
A J Harris BSc, MSc, DIC, MICE, CEng, FGS J Burridge MA CEng MIStructE MICE

Introduction
This chapter covers the analysis and design of reinforced concrete retaining
walls to Eurocodes 21 and 72. It considers retaining walls up to 3 m high and
propped basement walls up to two storeys high (7 m). These limits have been
chosen so that simplifications can be made in the geotechnical design. The
self-weight of these walls, including the self-weight of backfill on them, plays a
significant role in supporting the retained material. The chapter does not cover
the analysis and design of embedded retaining walls, which rely primarily on
passive earth pressure and flexural resistance to support the retained material.

A more general introduction to the Eurocodes is given in Chapters 1 and 2.

The essential features of Eurocode 7 Part 1 are covered in Chapter 6, which
includes a discussion of limit states, Geotechnical Categories, methods of
design, and the Geotechnical Design Report. It should be read in conjunction
with this chapter.

Essential features of Eurocode 7 are presented, along with theoretical models

for the analysis of retaining walls. A procedure for analysis and design is given
on page 70.

The principles presented below can also be used for basement walls. Further
guidance on basement walls, including the effect of shrinkage and movements
which are also appropriate for retaining walls, can be found in Concrete
Basements3.

Geotechnical Categories
Eurocode 7 Part 1 defines three Geotechnical Categories that can be used to
establish geotechnical design requirements. Simple structures with negliable
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

risk belong in Geotechnical Category 1. Walls that retain soil or water and do
not involve exceptional risk or difficult soil or loading conditions belong in
Geotechnical Category 2, for which routine procedures for field and laboratory
testing and for design and execution may be used. The design of such
structures requires quantitative geotechnical data and analysis.

Walls that involve abnormal risk or where there is unusual or exceptionally

difficult soil or loading conditions belong in Geotechnical Category 3, for
which alternative provisions and rules to those given in Eurocode 7 may be
needed; they are outside the scope of this publication.

Limit states
The design of reinforced concrete retaining walls requires verification that the

Copyright The Concrete Centre

following ultimate limit states are not exceeded (see Figure 1): Although Eurocode 7 provides three Design Approaches, the UK
Q Overall failure of the ground containing the wall. National Annex permits only Design Approach 1 to be used in the
UK. In this approach, two calculations must be performed with different
Q Failure of the wall by sliding.
combinations of partial factors for the STR/GEO limit state (see Table 1).
Q Failure of the wall by toppling (usually only relevant to walls
founded on rock). In calculations for Combination 1, partial factors greater than 1 are
applied to actions and structural materials only: to the self-weight of
Q Bearing failure of the ground beneath the wall (which may
the wall and backfill (treated as permanent actions); to any imposed
involve settlement and rotation of the wall).
loads or surcharges at the top of the wall (permanent or variable
Q Structural failure of the wall.
actions, as appropriate); and to the earth and pore water pressures
The resistance available in fine-grained soils, such as clays and silts, acting on the wall’s boundary (permanent actions).
depends greatly on how quickly excess pore water pressures in the
In calculations for Combination 2, partial factors greater than 1 are
ground dissipate after loading. The limit states above therefore need
applied to variable actions only and to the strength of the ground
to be checked both for short-term (i.e. undrained) behaviour of the
and structure: to the soil’s undrained strength in short-term (i.e.
ground and for long-term (i.e. drained) behaviour.
undrained) situations; and to the soil’s angle of shearing resistance
and effective cohesion in long-term (drained) situations.
Figure 1
Ultimate limit states for reinforced concrete retaining walls The design value, Fd, of an action can be expressed as: Fd = gF c Fk
where
gF = partial factor for the action
Fk = characteristic value of the action
c = either 1.0, c0, c1 or c2 (see Chapters 1 and 6)

Similarly the design value, Xd, of aanmaterial

action can be expressed
property as:
can be expressed as:
Xd = Xk / gM
where
gM = partial factor for of
thea action
material property
a) Overall stability Xk = characteristic value of athe
material
action property

It is important to note that the partial factor for h´ applies to tan h´,
i.e. tan h´d = (tan h´k)/gh.

Calculation models for

b) Sliding c) Toppling strength limit states
The mechanical behaviour of reinforced concrete cantilever walls is
commonly analysed using one of two assumed calculation models,
which are explained below.

It is assumed that soils have negligible effective cohesion c’, which

greatly simplifies the mathematics involved. This is a safe assumption
but, in the interests of economy, the effects of effective cohesion
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

d) Bearing e) Structural failure may be included in the design.

The beneficial effect of passive earth pressures in front of the wall

Table 1 is ignored in this publication, because its contribution to resistance
Partial factors to be used for retaining wall design according to is often small for reinforced concrete walls and is only mobilized
design approach 1 (UK National Annex) after considerable movement of the wall. Furthermore, Eurocode 7
Combin- Partial factors on Partial factors on material requires allowance to be made for unplanned excavations in front
ation actions properties of soil
of retaining walls, which further reduces the effects of passive
gGa gG,fav gQ g b gc gcu ga earth pressures.
1 1.35 1.0 1.5 1.0 1.0 1.0 1.0
2 1.0 1.0 1.3 1.25 1.25 1.4 1.0 In the expressions used here, the self-weights of the wall stem,
Key wall base, and backfill are favourable actions when sliding and
a gG is applied to unfavourable permanent actions toppling are considered, but are typically unfavourable actions for
b gh is applied to tan h’k
bearing (but since they reduce the inclination and eccentricity of

78
2
74
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
9. Retaining walls

the total action, they may be favourable – both situations should and the earth pressure coefficient used to calculate the thrust is
be checked). In the design calculations, favourable actions are given by Rankine’s formula.
multiplied by different partial factors to unfavourable actions – see
If bh is too small, then the wall stem interferes with the Rankine zone
Table 1.
and c should be reduced to c ≤ (h’/3 to 2h’/3) – although strictly
Rankine’s theory is no longer applicable and calculation model B
Calculation model A should be used instead.
In the first calculation model (see Figure 2), the wall including
backfill in block ABCD resists sliding and toppling caused by the For sliding and toppling, the most unfavourable location of any
earth pressures acting on the vertical ‘virtual’ plane, BF. The ground imposed surcharge is as shown in Figure 2a), with the edge of the
beneath the wall base must also be strong enough to carry the wall’s surcharge coincident with point B. In that position it increases
self-weight and any tractions (vertical components of force) on the unfavourable earth pressures acting on the virtual plane BF but does
virtual plane. not increase favourable vertical forces acting on the wall heel, DC.
For bearing, the most unfavourable location of the surcharge is when
An attractive feature of this model is that, provided the wall heel
it extends to the back of the wall, point A.
CD is large enough, the earth thrust Pa (see Figure 2b) is inclined at
an angle to the horizontal equal to the ground slope at the top of
the wall (i.e. c = b ), provided always that c ≤ h’. The test for the Calculation model B
model’s applicability is bh ≥ ha tan (45 – h’d /2), which (if met) means In the second calculation model (see Figure 3), the wall including
that a Rankine active zone forms within the confines of block ABCD backfill in block ACD resists sliding and toppling caused by earth
Figure 2
Calculation model A

Wf
a Ws
h

Figure 3
Calculation model B
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Wf
h

79
75
3
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

pressures acting on the inclined ‘virtual’ plane, AF. The earth

thrust Pa (Figure 3b) is inclined at an angle y + d to the horizontal. Design procedure
(The same model is used to analyse plain concrete gravity walls.) The
The overall procedure for the design of reinforced concrete retaining
ground beneath the wall base must also be strong enough to carry
walls is given in Figure 4 and explained in more detail over the next
the wall’s self-weight and the downwards component of the earth
few pages.
thrust on the virtual plane.
Since the sizing of reinforced concrete walls is often controlled by
A key theoretical advantage of this model is that it can be used
sliding with partial factors from Combination 2, it is sensible to
consistently for walls of all shapes and sizes. However, its main
undertake that verification first. The other checks should also be
disadvantage is that it involves careful consideration of trigonometry,
performed for both combinations. Bearing can also control the
with the angle y playing a significant role, leading to a complicated
design (depending on the wall geometry and soil properties).
expression for Ka and values are not so readily obtained from
published charts. To prevent the mathematics becoming too involved,
various simplifications about the wall’s geometry and that of the
Overall stability of the site
enclosed backfill are usually made. An essential part of the geotechnical design of retaining structures
is checking the stability of the site against overall rotational failure
Except for situations where bh is very small, it is reasonable to (see Figure 1a) and other forms of overall ground failure. Guidance
assume that the angle of friction d mobilized along the virtual plane on how to perform the necessary verifications is outside the scope
AF is equal to the angle of shearing resistance of the soil, h'. of this document, but can be found elsewhere, e.g. reference -.
The most unfavourable location of any imposed surcharge is typically
when it extends to the back of the wall, point A (as shown in Figure 3a). Initial sizing
However, since the surcharge also reduces the inclination and eccentricity The base width B of a reinforced concrete cantilever retaining wall is
of the total action, situations with it distant from the wall should also usually between 0.5 and 0.7 times its overall height, h (see Figure 5).
be considered. The breadth of the wall stem bs is normally h/15 to h/10 , as is
the thickness of the wall base tb. The breadth of the wall toe bt is
Figure 4 typically equal to B/4 to B/3.
Overall design procedure
For basement walls in most structures, the thickness will normally
Start be determined by the waterproofing requirements; often a minimum
thickness of 300 mm is used.
Check overall stability of the site For simplicity, it is assumed that adequate drainage systems will be
installed behind the retaining wall so that pore water pressures need
Carry out initial sizing of the wall not be considered. Since this is a potentially unsafe assumption, the
expressions given here need to be adjusted if this is not the case.
Determine characteristic material properties (see Figure 6)
Figure 5
Symbols for initial sizing
Calculate the characteristic value of actions (see Figure 6)

Calculate the design value of actions (see Figure 6)

No, revise geometry

Design against sliding

(see Figure 7)
Carry out separately for both
Combinations 1 and 2

Design against toppling

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

(see Figure 9)
Sufficient capacity?
Design against bearing
failure (see Figure 10)
Yes

Structural design (see

Figure 13) Design complete

80
4
76
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
9. Retaining walls

Material properties Panel 1

General expressions for geometry and actions
The characteristic value of a geotechnical parameter is defined in
BS EN 1997–1 Cl. 2.4.5.2(2)P as “a cautious estimate of the value Wk,s = bs H gk,c
affecting the occurrence of the limit state”, determined on the Wk,b = tb B gk,c
basis of laboratory and field test results complemented by well- bh = B – bs – bt
established experience and taking account of the zone of soil involved.
Characteristic geotechnical parameters should be determined by an Ls = bt + bs
2
experienced geotechnical engineer and recorded in the Geotechnical
Lb = B
Design Report. 2
The properties chosen for the backfill behind the retaining wall are For calculation model A:
critical to the geotechnical design of the wall and should be selected
hha = tb + H + bhtan b
carefully (see Figure 6). These include its weight density, g, angle of
b tan b
shearing resistance, h, and (if cohesive) undrained strength, cu. It is Wk,f = bh H + h gk,f

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
2
uncommon for retaining walls to retain cohesive fills, since this can b
Lf & bt + bs + h
lead to the retention of water (which should be avoided). Further, 2
considering cohesion reduces the calculated earth pressures, which W= b
is not conservative. For granular backfill the characteristic angle of Lvp = B
shearing resistance is normally taken between 30˚ and 35˚.
For calculation model B:
The foundation beneath the wall base is critical to the wall’s sliding
hb = tb + H
Figure 6 b H
Procedure for determining material properties, geometry and actions Wk,f & h gk,f
2
b
Lf = bt + bs + h
From Figure 4 3
bh
y = tan-1
Determine characteristic material properties hb
• Weight density (gk,f) and angle of shearing resistance (h’k,f)
W= y
of backfill
Lf
• Weight density (gk,fdn), undrained strength (cuk,fdn), and angle Lvp = B - bh/3
of shearing resistance (h’k,fdn) of foundation soil 3
• Weight density (gk,c) and cylinder strength (fck) of concrete

Panel 2
Determine initial geometry and actions (see Panel 1) General expressions for material properties and earth pressures
1 Determine initial geometry (see Figure 5)
• For calculation model B find inclination of virtual plane y ) For calculation model A:
2 Determine lever arms (see Figures 2c or 3c)
3 Calculate forces cos b – R sin2 hd,f – sin2 b
• Characteristic self-weights (Wk,s, Wk,b, Wk,f) Kad = cos b
• Total weight Wk,i = Wk,s + Wk,b + Wk,f cos b + R sin2 hd,f – sin2 b
• Total moment (Wk,i Li) = (Wk,s Ls) + (Wk,b Lb) + (Wk,f Lf)
gk,f h2
Pad = Kad gG 2 + gQ qkh
Carry out separately for both Combinations 1 and 2

For calculation model B:

Determine design material properties and earth
pressures (see Panel 2) sin b
mt = 1 cos-1 + h’d,f – b
1 Apply partial material factors to obtain design material 2 sin h’d,f
properties
• Weight density gd = gk / gg = gk since g = 1 1 ¾ sin+ h’d,f
• Angle of shearing resistance h’d = tan-1(tan h’k / g ’) Kn = e – 2 ( mt + b – h’d,f – y ) tan h’d,f
• Undrained strength cud = cuk / gcu 1 + sin h’d,f sin (2mt – hd,f )
2 Determine earth pressure
• Earth pressure coefficient Kad = function of h’d,f and b Note: This formula for Kn derives from
(depending on calculation model used) Kq = Kn cos2 b EN1997-1 Exp (C.6) but signs have been
• Earth pressure is function of vertical load and Kad changed to allow active pressures to be
Kg = Kn cos b cos (b – y ) calculated assuming hd,f is positive.
It has also been assumed that d = h and
gk,f h2 hence mw = –h. For passive pressures,
To Figure 4 Pad = gG Kg + gQ Kq qkh the value of hd,f used in the formula for
2
Kn should be negative

77
5
81
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

and bearing resistance and its properties should be chosen carefully. If air can reach the interface between the base and a clay foundation,
These include its weight density, angle of shearing resistance, and (if then the undrained resistance should be limited to HRd ≤ 0.4Vd
cohesive) undrained strength. For consideration of sliding, it is the – see BS EN 1997–1 Cl.6.5.3(12)P. If drainage occurs at the interface,
properties of the soil/concrete interface that are required unless a drained conditions may apply even for short-term loading.
shear key is provided. For bearing resistance a conservative estimate
The thrust depends largely on the strength properties of the backfill.
of the properties of the foundation soils is required.
If necessary, its magnitude can be reduced by using backfill with a
The weight density of concrete determines part of the wall’s greater angle of shearing resistance.
self-weight and should be taken as gk,c = 25 kN/m3 for
The resistance depends largely on the properties of the soil/structure
reinforced concrete in accordance with Eurocode 1/.
interface between the wall base and the foundation soil. It is usual
to assume full adhesion in calculations for the undrained condition
Design against sliding based on total stresses (i.e. to use full cu) and reduced friction in
The procedure for designing reinforced concrete retaining walls
calculations for the drained condition based on effective stresses
against sliding is given in Figure 7.
(i.e. to use dfdn ≤ ffdn). For concrete cast against soil, BS EN 1997–1
In the short-term (i.e. under undrained conditions), the horizontal Cl. 6.5.3(10) recommends dfdn = fcv, fdn ≤ ffdn, where fcv, fdn is the
component of the thrust on the virtual plane must be resisted by constant volume angle of shearing resistance of the foundation soil.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
adhesion on the underside of the wall base, HEd ≤ HRd, and by friction Values of fcv, fdn are independent of the soil’s relative density and
in the long-term (under drained conditions), HEd ≤ H’Rd. typically range from 27˚ to 33˚ for granular soils. For cohesive soils
the undrained situation will be critical.
Figure 7
Procedure for design against sliding
If necessary, a shear key can be used to improve the wall’s resistance
to sliding (Figure 8). The key has three benefits:
From Figure 4
Q It moves the failure surface away from the interface between the
wall and the foundation, so that an improved value of
Determine horizontal thrust on virtual plane (see Panel 2)
• HEd = Pad cos 1 dfdn = ffdn may be assumed.
Carry out separately for both Combinations 1 and 2

Q It lengthens the failure surface, from B to&R B2 + Dtb2.

If appropriate determine undrained sliding resistance on Q It potentially increases the passive resistance in front of the wall,
underside of wall base which is not considered here.
• HRd = cud,fdn B

Design against toppling

Determine drained sliding resistance on underside of wall base
The procedure for designing reinforced concrete retaining walls
• Calculate vertical action Vd = ga S Wk,i
i
• Calculate vertical traction from Pad (Panel 2) against toppling is given in Figure 9. Generally this check is only
• Calculate drainned sliding resistance, H’Rd (Panel 3) needed when the retaining wall is founded on rock or very hard soil.

The destabilising moment about the wall toe (point E in Figures 2a

Verify HEd ≤ HRd (if appropriate) and HEd ≤ H’Rd
and 3a) arising from the thrust on the virtual plane must be resisted

If necessary, repeat the above with a shear key Figure 9

Procedure for design against toppling
To Figure 4
From Figure 4

Panel 3 Determine destabilising moment MEd about point E.

Expressions for drained sliding resistance (see Panels 1 and 2) MEd = Pad cos W h/3
Carry out separately for both
Combinations 1 and 2

Undrained sliding resistance:

Determine stabilising moments about point E
HRd = cud,fdn B • Wall stem Md,s = Wd,s Ls
• Wall base Md,b = Wd,b Lb
Drained sliding resistance: • Backfill Md,f = Wd,f Lf
dd,fdn = hcvd,fdn • From active thrust, Md,vp = Pad sin W Lvp
• MRd = Md,s + Md,b + Md,f + Md,vp
H’Rd = Vd tan dd,fdn = gG,fav / Wk,i tan hcvd,fdn
i

With a shear key: Verify MEd ≤ MRd

H’Rd & gG,fav / Wk,i tan h’d,fdn 1+ Dt0

R
2
To Figure 4
i B

82
6
78
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
9. Retaining walls

by the stabilising moment about the same point arising from the
Figure 8
wall’s self-weight, i.e. MEd ≤ MRd. Effects of shear key

The destabilising moment depends largely on the strength properties

of the backfill. If necessary, its magnitude can be reduced by using a
backfill with a greater angle of shearing resistance.

The stabilising moment depends largely on the wall’s self-weight,

including the backfill.

(Somewhat counter-intuitively, the stability of a reinforced concrete 0

retaining wall supporting soil is not governed by limit state EQU,
defined in Eurocode 7 as “loss of stability of the structure or the
ground, considered as a rigid body”, because the strength of the
ground is significant in providing resistance. Instead, toppling is
usually governed by limit state GEO.) Panel 4
Expressions for bearing resistance
Typically, if the retaining wall has been sized appropriately for sliding,
h
then toppling will not be critical to the design. gG / (Wk,i Li ) + (Pad sin W Lvp ) – Pad cos W
B i 3
e= –
2 Vd + (Pad sin W)
Design against bearing failure
The procedure for designing reinforced concrete retaining walls B’ = B – 2 e
against bearing failure is given in Figure 10.
Undrained bearing resistance:
The bearing pressure acting beneath the wall base must be less than qRd = cud,fdn (p+2)i
Ncic + qc d+, qd ,
both the foundation’s short-term (undrained) bearing capacity,
where 1Nc= p + 2 P cos W
qEd ≤ qRd, and its long-term (drained) value, qEd ≤ q’Rd. ic = 1 + 1– ad R
2 B’
P ccos
ud,fdn W
The bearing pressure depends on the wall’s self-weight, including ic = 1 1 + 1– ad R
2 B’ cud,fdn
backfill, and any downwards traction on the virtual plane. Since the Drained bearing resistance:
centre of action of the resultant bearing force is almost inevitably Drained B’
q’Rd = q’bearing
d
Nq iq + (resistance:
gd,fdn – gw ) Ng ig + c’ Ncic
eccentric to the centre of the wall base, the bearing pressure must be 2
B’
calculated over an effective width B’ (see Figure 12). q’Rd = q’d Nq iq + ( gd,fdn – gw ) Ng ig 2
Pad cos W 2
iq = 1 –
The bearing capacity depends largely on the strength of the gG / PWk,icos+ (PW
ad
sin W) 2
i ad
foundation soil. Eurocode 7 gives simple analytical methods for iq = 1 –
1.5 gG / Wk,i + (Pad sin W)
g q i
bearing resistance calculations, based on classical bearing capacity ic = iq - (1 - iq)/Nctanh
1.5
theory. Since the resultant bearing force is almost inevitably inclined, g q

dimensionless factors reducing the standard bearing capacity factors Values for Nc, Ng and Nq can be obtained from Figure 11

Figure 10
Procedure for design against bearing failure Figure 11
Bearing capacity factors, N, from ground properties
From Figure 4
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

g
Determine bearing pressure (see Panels 1 and 2) c
qEd = (Vd + Pad sin 1) / B’
Carry out separately for both

Bearing capacity factor, N

Combinations 1 and 2

Determine undrained bearing capacity, qRd

(if appropriate, see Panel 4)

Determine drained bearing capacity q’Rd (see Panel 4)

Verify qEd ≤ qRd (if appropriate) and qEd ≤ q’Rd

To Figure 4
Angle , ´

83
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

are needed. The formulation for the drained bearing capacity given in This method for compaction earth pressure calculation assumes
Figure 10 and Panel 4 assumes that the groundwater level is at the that the fill is placed using a vibrating roller that is prevented from
underside of the base of the retaining wall. This will be conservative coming up to the face of the wall AD. If the roller is allowed to
for situations where groundwater can be guaranteed to be a distance reach AD then the depth s\ will be greater than that given in Panel
≥ B below the wall base. Note that the overburden pressure used in 6, owing to wall yield. Since the wall is not perfectly rigid, the
the expression for bearing capacity is that due to backfill above the equations given in Panel 6 are conservative.
wall’s toe (and is likely to be a small value).
At-rest earth pressures
Many basement walls are constructed to retain existing ground;
Structural design
they should be designed to withstand the at-rest earth pressures
A retaining wall is likely to be much stiffer than the ground it
illustrated in Figure 16.
supports, and therefore the stem of a reinforced concrete cantilever
wall must be designed to withstand earth pressures greater than The earth pressure coefficient used to determine the horizontal
the active pressures assumed in the calculations of sliding, toppling, pressures acting on the wall is given in BS EN 1997–1 Cl. 9.5.2(3)
and bearing resistance. Depending on how the wall is constructed it and (4) as: K0 = (1 – sin h’) ROCR (1 + sin b ) where OCR is the
should either be designed for ‘compaction pressures’ or for ‘at-rest’ overconsolidation ratio of the retained soil and b is the angle of
pressures.
Figure 13
As with sliding, toppling, and bearing resistance there are two Design procedure for structural design
combinations of partial factors to check at the ultimate limit state.

The design procedure is given in Figure 13. From Figure 4

Compaction earth pressures Check the stem of the retaining wall for compaction
pressures or at-rest conditions as appropriate:
Walls that are constructed before the placement of backfill should be
Carry out separately for both

• Maximum design moment = Ms (see Panel 5 or 6)

designed to withstand the compaction earth pressures (see Figure 14).
Combinations 1 and 2

• Maximum design shear force = Vs

The wall should be constructed with adequate drainage so that water • Refer to Chapter 3 for the ]^lb`g^qik^llbhglmhnl^
pressures will not build up against the stem in the long-term and so to check bending, shear anddeflection
do not need to be considered in the design;L1))+1ikhob]^l
`nb]Zg\^hgma^^Zkmaik^llnk^lmh[^k^lblm^]bg<e'-'.'+'.'.
Check the toe and heel of the wall in bending and shear

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
Panel 5 Zg]MZ[e^+`bo^ the earth pressure sh acting at depth z using the expressions in Panel 5 to determine applied
forces and the design expressions from Chapter 3 to
down the wall stem AD owing to the characteristic compaction line
check bending, shear and deflection
load Pk. For static rollers, the line load should be taken as the roller’s
self-weight. For vibrating compaction equipment, the sum of the
To Figure 4
self-weight and ma^\^gmkb_n`Zeob[kZmhk_hk\^lahne][^nl^]'B_ma^
\^gmkb_n`Ze_hk\^blngdghpg%ma^g_hkZob[kZmbg`khee^kmpb\^ma^
lê_&p^bàmfZr[^nl^]bglm^Z]'Mablkne^h_manf[lahne][^nl^]
pbma\ZnmbhgZg]blghmZiikhikbZm^_hknl^pbmaob[kZmbgìeZm^ Figure 14
\hfiZ\mhkl':ee_hk\^llahne][^^gm^k^]i^kngbme^g`maZehg`ma^ Compaction earth pressures for structural design of cantilever
retaining walls
pZee'

Figure 12
Effective base width, B’

zC
HC

84
8
80
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
9. Retaining walls

Panel 5 ground surface. The OCR is the ratio of maximum past level of
General expressions for designing walls for compaction pressures vertical stress to the current level of vertical effective stress.

OCR is typically obtained from an oedometer test and/or knowledge

Effective horizontal stress
Between J and K of the geological history of the site. It is not conservative to ignore it.
2Pdg k,f = K g z
shd =
p R pd k,f J Many basements involve one or two levels of propping and so
verification of sliding and toppling resistance is unnecessary (at least
Between K and D
for persistent design situations – they may still be relevant while the
shd = Kad gk,f z wall is being constructed).
Forces for stem design (see Figure 14)
Verification of the structural resistance of basement walls follows
m’h,compzc 2z m’ (z – z ) 2 (m’ – m’ )(Z – h )2
Moment, Ms = hc – c + h,comp D C – hd h,comp D C the same procedure as that for cantilever walls (see Figure 13), with
2 3 2 6
suitable allowance for any water pressures that may build up on the
m’h,compzc m’ (m’hd– m’h,comp )(ZD– hC )
Shear, Vs = + h,comp (zD– hC ) + back of the wall AD, especially if no provision is made for drainage.
2 2
where Table 8
mhd,J = mhd at J etc. Values of s'h,comp’ Zc’ and hc for different weights of compaction plant

Dead-weight of Critical depths Effective horizontal earth

Forces for heel design (see Figure 15b)
roller per width pressure, s’h,comp’ based on type
aG WK,f bh qEd (bh – B + B’)2 of roll, m of compactionA)
Moment, Mh & –
2 2 kg/m Zc hc Static DynamicB)
mm mm kPa kPa
Shear, Vh & aGW
WK,f – qEd (bh – B + B’) 75 80 310 3 6
100 90 360 4 7
Forces for toe design (see Figure 15a) 500 200 800 8 16
qEd bt2 1000 280 1130 11 23
Moment, Mt =
2 1300 320 1290 13 16
Shear, Vt = qEd bt A) Assuming = 20 kN/m3, K0 = 0.5, and g = 10m/s2.
B) Assuming the mass of a dynamic roller is twice its dead weight.

Panel 6
Figure 15 Expressions for the structural design of basement walls for ‘at-rest’
Pressure diagram for design of reinforced concrete base pressures

Soil pressure above K0d = (1 – sin h’d,f ) ROCR (1 + sin b )

toe ignored
sv,d = gd,f z + qd
Between A and W
ud = 0
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

sh,d = s’h,d = K0d sv,d

d d Between W and D
ud = gw (zD – zw)
s’h,d = K0d (sv,d – ud)
sh,d = s’h,d + ud
Forces for stem design
mhd,A zw zW mhd,W Zz W 2z W
Moment, Ms = zD – + zD – +
2 3 2 3
2mhd,W (zD – zW)2 mhd,D (zD – zW)2
+
6 6
mhd,A zW mhd,W zW mhd,W (zD – zW) mhd,D (zD – zW)
Shear, Vs = + + +
2 2 2 2
See Panel 5 for forces for base design.

85
8 '
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

When the structure retains: in the calculation of As,min and the size of the bar should be
Q Sands and gravels (i.e. high permeability soils) without a reliable limited as shown.
drainage system installed, or Q Where loading is the main cause of cracking, limit the bar
Q Silts and clays (i.e. low permeability soils) diameter or the bar spacing to that shown in Table 3.
In the absence of specific requirements (e.g. water-tightness), the
then BS EN 1997–1 Cl. 2.4.6.1(11) requires the water table to be
limiting calculated crack width wmax may be restricted to 0.3 mm in
taken at the “maximum possible level, which may be the ground
all exposure classes under quasi-permanent load combinations (see
surface ... unless the adequacy of the drainage system can be
Chapter 1).
demonstrated and its maintenance ensured”.
The minimum area of reinforcement in tensile zones to control
The relevant expressions for the total earth pressure s h (= effective
cracking should be calculated for each part of the member as follows:
earth pressure, s’h + pore water pressure, u) acting at depth z down
the wall AD are given in Panel 6 for a water table at depth dw below As,min = kc k fct,eff Act /ss
the top of the wall. These expressions assume that the wall is rigid
where
(owing to the propping) and no stress relief occurs during wall
kc = 1.0 for pure tension and 0.4 for pure bending (allows for
installation. Both of these assumptions are conservative.
the nature of the stress distribution within the section
immediately prior to cracking and for the change of the lever
Detailing arm as a result of cracking)
k = 1.0 where the wall is less than 300 mm and K = 0.65 where
Control of cracking it exceeds 800 mm thick. For intermediate conditions
It may be necessary to control the cracking of a reinforced concrete interpolation may be used. Factor allows for the effect of
wall, e.g. for aesthetic reasons or to minimise water ingress for a non-uniform self-equilibrating stresses, which lead to a
basement wall. For the latter, detailed guidance on the design of reduction of restraint forces
water-resisting basements is given in <hg\k^m^;Zl^f^gml3. fct,eff =mean value of the tensile strength of concrete Zmma^mbf^
\kZ\dlfZr[^_bklm^qi^\m^]mhh\\nkZmma^ZiikhikbZm^Z`^'
Control of cracking may either be assessed by using the deemed-to- _\m%^__6_\m%f!l^^mZ[e^,'*h_;L>G*22+&*&**"'?hkehg`&m^kf
satisfy method, which is presented here, or by calculating the crack ^__^\ml%+1&]Zrm^glbe^lmk^g`mabl\hglb]^k^]Zk^ZlhgZ[e^
widths directly (refer to Cl 7.3.4 of BS EN 1992–1–1). ZiikhqbfZmbhg

Cracks may be limited to acceptable widths by the following measures: Act = area of concrete in that part of the section which is
calculated to be in the tension zone i.e. in tension just before
Q Provide a minimum amount of reinforcement, As,min; so that the
the formation of the first crack
reinforcement does not yield immediately upon formation of the
first crack. Table 3
Maximum bar size or spacing to lmit crack width (mm)
Q Where restraint is the main cause of cracking, limit the bar
Steel Wmax = 0.3 Wmax = 0.2
diameter to that shown in Table 3. In this case any level of steel stress
(ss) Maximum Maximum Maximum Maximum
lmk^llfZr[^\ahl^g[nmma^l^e^\m^]oZen^fnlmma^g[^nl^] MPa bar size bar spacing bar size bar spacing
(mm) (mm) (mm) (mm)
Figure 16 160 32 300 25 200
Earth and pore water pressures for structural design of retaining 200 25
walls subject to 'at-rest' conditions OR 250 16 OR 150
240 16 200 12 100
280 12 150 8 50
320 10 100 6 –
360 8 50 5 –
Note
zW The steel stress may be estimated from the expression below
W fyk m As,req
ss =
gms nAs,prov d

zD where:
fyk = the characteristic reinforcement yields stress
gms = the partial factor for reinforcement steel
m = the total load from quasi-permanent combination
n = the total load from ULS combination
As,req = the area of reinforcement at the ULS
As,prov = the area of reinforcement provided
d = the ratio of redistribution moment to elastic moment

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

86
10
82
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
9. Retaining walls

ss = absolute value of the maximum stress permitted in the For walls with a high axial load (eg basement walls), the main
reinforcement immediately after the formation of the crack. reinforcement placed nearest to the wall faces should have transverse
The value should be chosen bearing in mind the limits on bar reinforcement in the form of links with at least four per m2 of wall
size and spacing indicated in Table 3 area. Where welded mesh and bars of diameter f ≤ 16 mm are used
with cover larger than 2f, transverse reinforcement is not required.
Large radius bends
It is often necessary to provide large radius bends to the main Horizontal reinforcement
reinforcement at the base of the stem because of the high tensile The minimum area of horizontal reinforcement is the greater of
forces in the bars. The minimum mandrel diameter, fm.min should be either 25% of vertical reinforcement or 0.001 Ac. However, where
assessed as follows: crack control is important, early age thermal and shrinkage effects
should be considered.
fm.min ≥ Fbt(1/ab+1/(2f))/fcd
Where flexural forces dominate, these requirements may be relaxed
where
to 20% of the vertical reinforcement area.
Fbt = tensile force from ultimate loads in a bar at the start of
the bend
ab = half the pitch of the bars or nominal cover plus f/2
f = bar diameter
Practical issues
fcd = design value of concrete compressive strength
Design for movement
The Standard method of detailing structural concrete, appendix Concrete shrinks due to early thermal effects immediately after
B,contains some useful tables that will assist in determining the casting. The base of a retaining structure is usually restrained by the
minimum mandrel size. soil on which it is bearing, which induces strains in the concrete.
Therefore, the reinforcement detailing, pour size and sequence of
Rules for spacing and quantity of construction should be planned to control the resultant cracking.
reinforcement
Typically pour sizes are up to one storey high, to limit hydrostatic
Vertical reinforcement pressures on formwork. The National structural concrete specification1
Where axial forces dominate, the minimum area of vertical recommends pour sizes with a maximum area of 25 m2 and
reinforcement is 0.002Ac; half this area should be placed in each maximum dimension 5 m for water-resisting walls. The contractor
face. Otherwise, the minimum percentage of reinforcement can will seek to use the largest pour size possible and will want to ensure
be obtained from Table 6 of Chapter 3. Outside lap locations, the that the minimum volume of concrete for a pour is 6 m3 (i.e. a full
maximum area of vertical reinforcement is 0.04Ac;; this may be load of a ready-mixed concrete). It is usual to cast alternate bays
doubled at lap locations. in a wall to reduce the effects of early shrinkage. Further advice on
calculating strains and crack widths for restrained walls can be found
The distance between two adjacent vertical bars should not exceed
in appendices L and M of BS EN 1992–31.
the lesser of either three times the wall thickness or 400 mm.
For long lengths of retaining walls, it is generally accepted practice
Figure 17
to have expansion joints every 20 – 30 m; even so the base of the
Typical drainage layout for a retaining wall
wall will still be restrained. For a temperature range of 40°C, the joint
should allow for 10 mm of movement for every 10 m length of wall.

Drainage
To prevent pore water pressures from building up, it is important
to provide drainage material behind a retaining wall. The zone
PP ZLGH
JUDQXODU EDFNILOO immediately behind the wall should be of a free-draining granular
material, which should be protected to prevent it becoming blocked
with fines. A drainage pipe, laid to falls, should be provided at the
:HHS KROH
'UDLQDJH SLSH base of the free-draining material. The system should be designed for
the anticipated rainfall, and rodding points provided for maintenance
of the drainage systems. Weepholes should be provided as a back-up
as they act as an overflow and as a visual warning that maintenance
is required should the primary system become blocked. A typical
/DUJH UDGLXV EHQG drainage system is illustrated in Figure 17.
LI UHTXLUHG

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
87
11
83
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
9. Retaining walls

Construction The designer should consider how the temporary works will
It is particularly important when designing retaining walls to consider affect the installation of the water-proofing for a basement wall.
how they will be constructed. Often some form of temporary works For instance, a sheet pile wall may be used to affix an external
is required and these may impact on the design. The simplest form of waterproofing system, but this would prevent the sheet piles
construction is in an open excavation with the sides battered back to from being removed at the end of construction. Similarly, external
a safe angle to allow the construction of the wall. In this case there waterproofing should not be used where temporary propping
is little impact on the design, although the loads imposed during would penetrate it, because it will not be possible to complete the
compaction of the backfill may be onerous. waterproofing when the props are removed.

Where there is insufficient space for opening an excavation, either a The temporary works may affect the soil pressures acting on the
king post wall or sheet pile wall will be used as temporary supports, wall and the construction sequence could give rise to temporary
and these may require propping, especially for a two-storey basement. actions that exceed the permanent actions imposed on the wall.
The designer should consider this aspect and prepare a method
The designer should ensure there is sufficient space to install the
statement indicating the assumptions made so the temporary works
temporary works. It is possible to use contiguous piles, secant piles
designer can work to the assumptions made or make alternative
or diaphragm walling as temporary supports but it is more usual for
proposals.
these to be installed as part of the permanent works.

References
1 BRITISH STANDARDS INSTITUTION, BS EN 1992, Eurocode 2: Design of concrete structures. BSI (4 parts).
2 BRITISH STANDARDS INSTITUTION, BS EN 1997, Eurocode 7: Geotechnical design. BSI (2 parts).
3 NARAYANAN, R.S & GOODCHILD, C.H, Concrete Basements, The Concrete Centre, 2012.
4 FRANK, R, BAUDUIN, C, DRISCOLL, R, KAVVADAS, M, KREBS OVESEN, N, ORR, T & SCHUPPENER, B. Designers’ guide to BS EN 1997–1,
Eurocode 7: Geotechnical design – General rules. Thomas Telford Publishing, 2004.
5 CLAYTON, C R I & MILITITSKY, J. Earth pressure and earth-retaining structures. Blackie & Son Ltd, Glasgow, 1986.
6 BRITISH STANDARDS INSTITUTION. BS EN 1991–1–1: General actions – Densities, self-weight, imposed loads for buildings. BSI, 2002.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
7 INGOLD, T S. The effects of compaction on retaining walls, Geotechnique 29(3), pp. 265–283, 1979.
8 BRITISH STANDARDS INSTITUTION, BS 8002: Code of Practice for Earth-Retaining Structures. BSI, 2015.
9 PARSONS, A W. Compaction of soils and granular materials. Transport Research Laboratory, 1992.
10 INSTITUTION OF STRUCTURAL ENGINEERS/THE CONCRETE SOCIETY. Standard method of detailing structural concrete. IStructE/The Concrete
Society, 2006.
11 CONSTRUCT. National structural concrete specification (fourth edition). The Concrete Society, 2010 .

88
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

10. Detailing
O Brooker BEng, CEng, MICE, MIStructE, MCS J Burridge MA CEng MIStructE MICE

Introduction
This chapter is intended for use by detailers to prepare reinforcement drawings
for projects that have been designed using Eurocode 21. It provides a summary
of the requirements of the Eurocode and simplifies them where appropriate.

The following standards may also need to be referenced:

■ BS 4449: Specification for carbon steel bars for the reinforcement of
concrete2, which is a complementary standard to BS EN 10080: Steel for
the reinforcement of concrete3 and Normative Annex C of Eurocode 2.
■ BS 8666: 2005, Scheduling, dimensioning, bending and cutting of steel
reinforcement for concrete – specification4 .

In this publication a number of assumptions have been made. Many of the

derived expressions and figures assume UK values for the National Determined
Parameters (NDPs). It is assumed that bars sizes are 40 mm or less and that
the bars will not be bundled together. It is also assumed that the concrete
class will not exceed C50/60. For additional requirements outside these limits,
reference should be made to Eurocode 2.

This chapter focuses on detailing the reinforcement to comply with Eurocode 2;

guidance on procedures, responsibilities and preparation of drawings can be
found in other documents5,6,7.

Type and grade of reinforcement

The 2005 revision of BS 4449 introduced a characteristic yield strength
of 500 MPa. There are now three grades of reinforcement, A, B and C (see
Table 1), which offer increasing ductility. It is expected that for the design of
UK buildings all three grades A, B or C will be appropriate and in this case the
bar size can be prefixed with an H (e.g. H12). Grade A is not suitable for use
where redistribution above 20% has been assumed in the design and a
grade B bar should be specified in these circumstances (e.g. B12). Grade C is
for seismic conditions or where additional ductility is required.
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,

Copyright The Concrete Centre

Table 1
Notation for steel reinforcement
Cover
Type of steel reinforcement Notation The nominal cover should generally be specified by the designer
For f ≤ 12 mm, Grade B500A, Grade B500B or Grade B500C H and full details of how to determine this are given in Chapter 2. The
conforming to BS 4449:2005. For f > 12 mm, Grade B500B or nominal cover should be shown on the drawings and should refer to
Grade B500C conforming to BS 4449:2005
the reinforcement nearest to the surface of the concrete e.g. the links
Grade B500A conforming to BS 4449: 2005 A
in a beam.
Grade B500B or Grade B500C conforming to BS 4449: 2005 B
Also, the cover to the main bar should be at least equal to the size of
Grade B500C conforming to BS 4449: 2005 C
that bar, plus the allowance for deviations, Dcdev. Where there are no
Reinforcement of a type not included in the above list having X
material properties that are defined in the design or contract links the nominal cover should be at least equal to the size of the bar
specification. plus Dcdev, this may be significant for bar diameters greater than
Note 12 mm. Dcdev may be 5 or 10 mm depending on the quality assurance
In the Grade description B500A, etc., ’B’ indicates reinforcing steel.
system assumed for the project. If the cover needs to be increased to
meet these requirements, the detailer should consult with the designer.
Figure 1
Description of bond conditions

Direction of concreting Direction of concreting Anchorage and lap lengths

Eurocode 2 introduces a range of factors (a1 to a6) for use when
a
250 calculating the appropriate anchorage and lap lengths. A number of
assumptions can be made that enable Table 2 to be developed for
a) 45º < a < 90º c) h > 250 mm
anchorage and lap lengths. If the conditions noted in the table are not
Direction of concreting
Direction of concreting
met then reference should be made to Eurocode 2. Lap lengths for
≥ 300 unequal size bars may be based on the smaller bar, although this is not
stated in the Code.
h h

b) h < 250 mm d) h > 600 mm Anchorage of bars and links

Key

‘Good’ bond conditions ‘Poor’ bond conditions All reinforcement should be anchored so that the forces in it are safely
transmitted to the surrounding concrete by bond without causing
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Table 2
Anchorage and lap lengths for concrete class C25/30 (mm)

Bond Reinforcement in tension, bar diameter, f (mm) Reinforcement

condition, in
(see Figure 1) 8 10 12 16 20 25 32 40 compression
Good 230 320 410 600 780 1010 1300 1760 40f
Straight bars only
Anchorage Poor 330 450 580 850 1120 1450 1850 2510 58f
length, lbd Good 320 410 490 650 810 1010 1300 1760 40f
Other bars
Poor 460 580 700 930 1160 1450 1850 2510 58f
50% lapped in one location Good 320 440 570 830 1090 1420 1810 2460 57f
(a6 = 1.4) Poor 460 630 820 1190 1560 2020 2590 3520 81f
Lap length,
l0 Good 340 470 610 890 1170 1520 1940 2640 61f
100% lapped in one location
(a6 = 1.5) Poor 490 680 870 1270 1670 2170 2770 3770 87f
Notes
1 Nominal cover to all sides ≥ 25 mm, [i.e. a2 ≤ 1]. At laps, clear distance between bars ≤ 50mm.
2 a1 = a3 = a4 = a5 = 1.0. For the beneficial effects of shape of bar, cover and confinement see Eurocode 2, Table 8.2.
3 Design stress has been taken as 435 MPa. Where the design stress in the bar at the position from where the anchorage is measured, ssd, is less than 435 MPa the figures in this
table can be factored by ssd/435. The minimum lap length is given in cl 8.7.3 of Eurocode 2.
4 The anchorage and lap lengths have been rounded up to the nearest 10 mm.
5 Where 33% of bars are lapped in one location, decrease the lap lengths for ‘50% lapped in one location’ by a factor of 0.82.
6 The figures in this table have been prepared for concrete class C25/30; refer to Table 13 for other classes or use the following factors for other concrete classes.

Concrete class C20/25 C28/35 C30/37 C32/40 C35/45 C40/50 C45/55 C50/60
Factor 1.16 0.93 0.89 0.85 0.80 0.73 0.68 0.63

90
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
10. Detailing

cracking or spalling. The design anchorage length, lbd, (which can be Bars in compression
obtained from Table 2) is measured along the centreline of the bar In addition to the rules for bars in tension (Figure 6a), one bar of the
(see Figure 2). The anchorage of links is shown in Figure 3. transverse reinforcement should be placed outside each end of the lap
length of bars in compression and within 4f of the ends of the lap
length (see Figure 6b).
Arrangement of laps
Figure 2
Where possible laps in a member should be staggered (see Figure 4) Design anchorage length lbd, for any shape measured along the
centreline
and not located in areas of high stress. The arrangement of lapped bars
should comply with Figure 5, as set out below:
1. The clear distance between lapped bars should not be greater than
4f or 50 mm, otherwise the lap length should be increased by a
lbd f

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
length equal to the clear distance.
2. The longitudinal distance between two adjacent laps should not be
less than 0.3 times the lap length, l0. Where this is not the case, the
bars should be considered as being lapped in one section. Figure 3
Anchorage of links
3. In case of adjacent laps, the clear distance between adjacent bars
should not be less than 2f or 20 mm. 5f, but 10f, but
≥ 50 mm ≥ 70 mm

When the provisions comply with 1 and 3 above, the permissible

percentage of lapped bars in tension may be 100% where the bars are
all in one layer. Where the bars are in several layers no more than 50%
should be lapped in any one layer.
f f

All bars in compression and secondary (distribution) reinforcement may

a) Bend angle > 150º b) Bend angle ≤ 150º
be lapped in the same location.

Figure 4
Transverse reinforcement Percentage of lapped bars in one lapped section

l0
Bars in tension
Transverse tensile stresses occur at the ends of lapped bars. Where the bar 1

diameter, f, of the lapped bars is less than 20 mm, or the percentage

bar 2
of lapped bars in any section is less than 25%, then any transverse
reinforcement or links necessary for other reasons may be assumed bar 3
sufficient for the transverse tensile forces without further justification.
bar 4
Example: bars 2 and 3 are
Where the diameter, f, of the lapped bars is greater than or equal to outside the section being
0.65l0 0.65l0
20 mm, the transverse reinforcement should have a total area, Ast (sum considered.
Therefore a6 = 1.4
of all legs parallel to the layer of the spliced reinforcement – see Figure Section considered
6a) of not less than the area As of one lapped bar (YAst ≥ 1.0As). The
transverse bar should be placed perpendicular to the direction of the
lapped reinforcement. Table 3 gives recommended minimum areas for Figure 5
transverse reinforcement. Where the lapped bars in a slab are located in Arranging adjacent lapping bars
an area of low stress, e.g. near the point of contraflexure, it is generally ≥ 0.3l0 l0
acceptable to assume that transverse reinforcement is not required. ≤ 50 mm
Fs ≤ 4f f
Fs

If more than 50% of the bars are lapped in one location and the
distance, a, between adjacent laps at a section is ≤ 10f (see Figure 5) a
Fs ≥ 2f
transverse reinforcement should be formed by links or U-bars anchored ≥ 20 mm Fs
into the body of the section. Fs
Fs

91
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Beams Figure 7
Illustration of curtailment of longitudinal reinforcement

Curtailment Hogging reinforcement

Unless the additional tensile force in the longitudinal reinforcement

due to shear has been calculated, the curtailment length of the Envelope of MEd/z + NEd lbd
longitudinal reinforcement should be extended beyond the point at lbd
which it is required for flexural strength (this is known as the ‘shift Acting tensile force Fs
Resisting tensile force FRs lbd
rule’) using the following expression (see also Figure 7):
al = z cot y /2 for vertical shear reinforcement.
D Ftd
al
where
z = lever arm
y = angle of compression strut al
lbd
This can conservatively be taken as: D Ftd

lbd lbd
al = 1.125d
lbd lbd
For beams designed using the co-efficients given in Table 3 of Chapter 4,
the simplified rules shown in Figure 8 may be used. However, the
simplifications are conservative and economies can be achieved by Sagging reinforcement

curtailing bars to suit the actual moments.

Figure 6 Figure 8
Transverse reinforcement for lapped splices Simplified detailing rules for beams

Ast/2 Ast/2 Face of support Reinforcement for

l0/3 100% maximum hogging moment
l0/3
≤ 150 mm
Fs 0.15l + al ≥ lbd 60%
Fs
0.30l + al 35%*
*reduce to 25%
a) Bars in tension for equal spans
l0

a) Continuous member, top reinforcement

Ast/2 Ast/2

≤ 150 mm 30%
Fs
Fs
0.30l – al

Position of 100%
b) Bars in compression l0
effective
support Reinforcement for maximum sagging moment
4f l0/3 l0/3 4f

b) Continuous member, bottom reinforcement

Table 3
Bar sizes for transverse reinforcement
25%

Lap length Number Bar size (mm) lbd

(mm), for of bars
transverse at end 20 25 32 40 0.08l
100%
bars at 150 of each
mm centresa lap As = 314 As = 491 As = 804 As = 1260 Position of
effective support
≤450 2 10 16 16 25
c) Simple support, bottom reinforcement
451 – 900 3 10 12 16 20
901 – 1350 4 8 10 12 16 Notes
1351 – 1800 5 8 8 12 16 1 l is the effective length.
2 al is the distance to allow for tensile force due to shear force.
1801 – 2250 6 8 8 10 12
3 lbd is the design anchorage length.
2251 – 2700 7 N/A 8 10 12 4 Qk ≤ Gk.
Key 5 Minimum of two spans required.
a For transverse bars at less than 150 mm centres use the following expression to 6 Applies to uniformly distributed loads only.
calculate the required number of bars and hence the required transverse bar diameter: 7 The shortest span must be greater than or equal to 0.85 times the longest span.
Number of bars required = 1 + l0/(3s) where s = spacing of the transverse bars. 8 Applies where 15% redistribution has been used.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

92
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
10. Detailing

Reinforcement in end supports Minimum spacing of reinforcement

In monolithic construction, even when simple supports have been The minimum clear distance between bars should be the greater of:
assumed in design, the section at supports (top reinforcement) should ■ Bar diameter
be designed for a bending moment arising from partial fixity of at ■ Aggregate size plus 5 mm
least 25% of the maximum bending moment in the span (i.e. provide ■ 20 mm
25% of mid-span bottom reinforcement).
Shear reinforcement
The area of bottom reinforcement provided at supports with little or no The longitudinal spacing of vertical shear reinforcement should not
end fixity assumed in design, should be at least 25% of the area of steel exceed 0.75d. Note the requirement for a maximum spacing of
provided in the span. The bars should be anchored to resist a force , FE. 150 mm where the shear reinforcement acts as a transverse
reinforcement at laps in the longitudinal bars. The transverse spacing
FE = (|VEd| al / z) + NEd
of the legs in a series of shear links should not exceed:
where
st,max = 0.75d ≤ 600 mm
|VEd| = absolute value of shear force
NEd = the axial force if present The minimum area of shear reinforcement in beams, Asw,min should be
calculated from:
The anchorage, lbd, should be measured beyond the line of contact
Asw
between the beam and support. ≥ rw,min where rw,min can be obtained from Table 4.
s bw
Provided ssd is taken as 435 MPa in the calculation of the anchorage

Slabs
length (which is assumed in Tables 2 and 13) then it should not be
necessary to calculate FE.

Flanged beams Curtailment

At supports the tension reinforcement to resist hogging moments The curtailment rules for beams should be followed, except that a
should be distributed across the full width of the effective flange as value of al = d may be used.
shown in Figure 9; part of it may be concentrated over the web.
For slabs designed using the co-efficients given in Table 3 of Chapter 3,
Minimum area of longitudinal reinforcement the simplified rules shown in Figure 10 may be used.
The minimum area of reinforcement is As,min = 0.26 fctm bt d/fyk but
not less than 0.0013btd, where bt is the mean width of the tension Reinforcement in end supports
zone (see Table 4). For a T-beam with the flange in compression, only In simply supported slabs, the area of reinforcement may be reduced
the width of the web is taken into account in calculating the value to half the calculated span reinforcement and continued up to the
of bt. support, otherwise 100% of the reinforcement may be continued
to the support. Beyond the face of the support 15% of the area of
Maximum area of longitudinal reinforcement maximum reinforcement should be provided (see Figure 10c). The
Outside lap locations, the maximum area of tension or compression bars should be anchored to resist a force, FE, as given in the section
reinforcement should not exceed As,max = 0.04 Ac. on beams.
Table 4
Figure 9 Minimum percentage of reinforcement required
Placing of tension reinforcement in flanged cross section
fck fctm Minimum percentage rw, min x 10-3
beff (0.26 fctm / fyka)

As 25 2.6 0.13% 0.80

28 2.8 0.14% 0.85

hf 30 2.9 0.15% 0.88

32 3.0 0.16% 0.91

beff1 bw beff2 35 3.2 0.17% 0.95

40 3.5 0.18% 1.01
45 3.8 0.20% 1.07
50 4.1 0.21% 1.13
Key
a Assuming fyk = 500 MPa

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

93
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Similar to beams, even when simple supports have been assumed in not exceed 320 MPa for a typical slab. Where the slab supports office
design, end supports of slabs should have top reinforcement equal to or residential areas it is unlikely that ss will exceed 280 MPa. ss may
at least 25% mid-span bottom reinforcement and this reinforcement be estimated using Figure 6 on page 15.
should extend at least 20% of the span from the face of support.
Minimum areas of reinforcement
Minimum spacing requirements The minimum area of reinforcement to be provided varies with the
The minimum clear distance between bars (horizontal or vertical) concrete strength (see Table 4).
should not be less than the bar size, b, (dg + 5 mm), or 20 mm, where
dg is the maximum size of aggregate. Maximum area of longitudinal reinforcement
Outside lap locations, the maximum area of tension or compression
Maximum spacing of reinforcement reinforcement, should not exceed As,max = 0.04Ac. At lap locations
For slabs less than 200 mm thick the following maximum spacing As,max = 0.08Ac.
rules apply (h is the depth of the slab):
■ For the principal reinforcement: 3h but not more than 400 mm.
■ For the secondary reinforcement: 3.5h but not more than 450 mm.
Edge reinforcement
The exception is in areas with concentrated loads or areas of Along a free (unsupported) edge, a slab should normally contain longitudinal
maximum moment where the following applies: and transverse reinforcement, generally arranged as shown in Figure 11.
■ For the principal reinforcement: 2h but not more than 250 mm.
■ For the secondary reinforcement: 3h but not more than 400 mm.

For slabs 200 mm thick or greater, the spacing requirements are given Flat slabs
in Table 5. Where the designer has not specified the required spacing
A flat slab should be divided into column and middle strips (see
or provided the steel stress, ss, it can generally be assumed that ss will
Figure 12); the division of the moments between the column and
middle strips is given in Table 6.
Figure 10
Simplified detailing rules for slabs Figure 11
Edge reinforcement for slab
Face of support Reinforcement for

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
100% maximum hogging moment

0.15l ≥ lbd 50%

h
0.30l

≥ 2h
a) Continuous member, top reinforcement

Table 5
40% Maximum bar size or spacing to limit crack width

0.2l Steel wmax = 0.4 mm wmax = 0.3 mm

Position of 100% stress
Maximum Maximum Maximum Maximum
effective (ss) MPa bar size bar spacing bar size bar spacing
support Reinforcement for
maximum sagging moment (mm) (mm) (mm) (mm)
b) Continuous member, bottom reinforcement 160 40 300 32 300
200 32 300 25 250
25% OR OR
15%
240 20 250 16 200

lbd
280 16 200 12 150
320 12 150 10 100
Face of 100%
support 360 10 100 8 50

c) Simple support, bottom reinforcement

Table 6
Notes Apportionment of bending moments in flat slabs – equivalent frame method
1 l is the effective length.
Location Negative moments Positive moments
2 lbd is the design anchorage length.
3 Qk ≤ 1.25 Gk and qk ≤ 5kN/m2. Column strip 60% – 80% 50% – 70%
4 Minimum of two spans required. Middle strip 40% – 20% 50% – 30%
5 Applies to uniformly distributed loads only.
Notes
6 The shortest span must be greater than or equal to 0.85 times the longest span.
The total negative and positive moments to be resisted by the column and middle
7 Applies where 20% redistribution has been used. strips together should always add up to 100%

94
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
10. Detailing

Figure 12 The intention is to provide an even distribution/density of punching

Division of panels in flat slabs shear reinforcement within the zone where it is required. One
simplication to enable rectangular perimeters of sheer reinforcement is
lx > ly
to use an intensity of Asw/u1 around rectangular perimeters.
ly /4 ly /4 Middle strip = lx – ly /2

The minimum area of a link leg for vertical punching shear reinforcement is
ly /4
1.5Asw,min /(sr s t ) ≥ 0.08 3f ck f yk
ly /4 which can be rearranged as:
Asw,min ≥ (s r s t )/F
Middle strip = ly /2 ly
where
sr = the spacing of the links in the radial direction
Column strip = ly /2 s t = the spacing of the links in the tangential direction
F = factor obtained from Table 7

Figure 13
Effective width, be of a flat slab

At internal columns, unless rigorous serviceability calculations are cx cx

Slab edge
carried out, top reinforcement of area 0.5 At should be placed in a
Slab edge
width equal to the sum of 0.125 times the panel width on either side cy
of the column. At represents the area of reinforcement required to cy
y
resist the full negative moment from the sum of the two half panels y
each side of the column. It is also advisable to apply this requirement
to perimeter columns as far as is possible. z
be = cx + y

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
be = z + y/2
At internal columns at least two bars of bottom reinforcement in each Slab edge
orthogonal direction should be provided and they should pass between y can be > cy z can be > cx and y can be > cy
the column reinforcement. Whilst it is not a code requirement it is a) Edge column b) Corner column
considered good practice to provide two bars running parallel to the Note
y is the distance from the edge of the slab to the innermost face of the column
slab edge between the reinforcement of an external column.

Reinforcement perpendicular to a free edge required to transmit Figure 14

bending moments from the slab to an edge or corner column should Punching shear layout
be placed within the effective width, be, shown in Figure 13.
Outer perimeter of
shear reinforcement Outer control
perimeter
u out
Punching shear reinforcement
Where punching shear reinforcement is required the following rules ≤ 0.75d
should be observed. A A
≤1.5d
■ It should be provided between the face of the column and kd ≤ 1.5d
sr (2d if > 2d
inside the outer perimeter where shear reinforcement is no longer from column)
st
required. k is 1.5, unless the perimeter at which reinforcement is no
longer required is less than 3d from the face of the column. In this
case the reinforcement should be placed in the zone 0.3d to 1.5d
from the face of the column.
0.3d ≤ si ≤ 0.5d
■ There should be at least two perimeters of shear links. s r ≤ 0.75 d
■ The radial spacing of the links, sr should not exceed 0.75d (see Figure 14).
■ The tangential spacing of the links, sd should not exceed 1.5d kd
within 2d of the column face.
■ The tangential spacing of the links should not exceed 2d for any
other perimeter. Outer control
perimeter
■ The distance between the face of the column and the nearest shear Section A - A
reinforcement should be between 0.3d and 0.5d

95
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Columns and walls Lapping fabric

Maximum areas of reinforcement Unless ‘flying end’ fabric is being specified, laps of fabric should be
In Eurocode 2 the maximum nominal reinforcement area for columns arranged as shown in Figure 15. When fabric reinforcement is lapped
and walls outside laps is 4% compared with 6% in BS 8110. However, by layering, the following should be noted:
this area can be increased provided that the concrete can be placed ■ Permissible percentage of fabric main reinforcement that may be
and compacted sufficiently. Self-compacting concrete may be used lapped in any section is 100% if (As/s) ≤ 1200 mm2/m (where s is
for particularly congested situations, where the reinforcing bars should the spacing of bars) and 60% if As/s> 1200 mm2/m.
be spaced to ensure that the concrete can flow around them. Further ■ All secondary reinforcement may be lapped at the same location
guidance can be found in Self-compacting concrete8. and the minimum lap length l0,min for layered fabric is as follows:
≥ 150 mm for f ≤ 6 mm
Minimum reinforcement requirements ≥ 250 mm for 6 mm < f ≤ 8.5 mm
The recommended minimum diameter of longitudinal reinforcement ≥ 350 mm for 8.5 mm < f ≤ 12 mm
in columns is 12 mm. The minimum area of longitudinal reinforcement
in columns is given by: As,min = 0.10 NEd/fyd ≥ 0.002Ac. The diameter There should generally be at least two bar pitches within the lap
of the transverse reinforcement (link) should not be less than 6 mm length. This could be reduced to one bar pitch for f ≤ 6 mm.
or one quarter of the maximum diameter of the longitudinal bars (see
Table 8). No longitudinal bar should be more than 150 mm from a
restrained bar. Tolerances
The tolerances for cutting and/or bending dimensions are given in Table 10
Particular requirements for walls
and should be taken into account when completing the bar schedule.
The minimum area of vertical reinforcement in walls is given by:
As,vmin = 0.002Ac (see also Table 9). Half the area should be provided in Where the reinforcement is required to fit between two concrete faces
each face. (e.g. links) then an allowance should be made for deviations in the member
size and bending tolerances. There is no guidance given in Eurocode 2, but
The distance between two adjacent vertical bars should not exceed Table 11 gives guidance on the deductions to be made for deviations.
the lesser of either three times the wall thickness or 400 mm.
Table 9
Minimum area of vertical reinforcement in walls (half in each face)
The minimum area of horizontal reinforcement in each face of a wall
Wall thickness (mm) As,min /m length of wall (mm2)
is the greater of either 25% of vertical reinforcement or 0.001Ac.
200 400
However, where crack control is important, early age thermal and
250 500
shrinkage effects should be considered. 300 600
350 700
There is no advice given in the Code on provision of reinforcement 400 800
to control cracking in plain walls, but reinforcement may be provided
if required. Table 10
Tolerance
Cutting and bending processes Tolerance (mm)
Table 7
Factor, F, for determining Asw, min Cutting of straight lengths (including +25, –25
reinforcement for subsequent bending)
fck 25 28 30 32 35 40 45 50 Bending:
Factor, F 1875 1772 1712 1657 1585 1482 1398 1326 ≤ 1000 mm +5, –5

Note > 1000 mm to ≤ 2000 mm +5, –10

fyk has been taken as 500 MPa > 2000 mm +5, –25

Table 11
Table 8 Deductions to bar dimensions to allow for deviations between two
Requirements for column reinforcement concrete faces when using BS EN 136709,10
Bar dia. (mm) 12 16 20 25 32 40 Distance between concrete faces T (mm) Total deduction (mm)
Max spacinga (mm) 144b 192b 240b 240b 240b 240b ≤200 5
Min link dia. (mm) 6 c 6c 6c 8 8 10 ≤400 10

Key ≤1000 15
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

a At a distance greater than the larger dimension of the column above or below a ≤2000 20
beam or slab, dimensions can be increased by a factor of 1.67. >2000 30
b But not greater than minimum dimension of the column.
c 6 mm bars are not readily available in the UK. Note: The above deductions are to be used to determine bending
dimensions. An additional 10mm should be deducted when determining
the cutting length of straight bars whose ends are to be placed between
96 concrete surfaces.
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
10. Detailing

Figure 15 lr = the greater of the distances (in m) between the centres of the
Lapping of welded fabric columns, frames or walls supporting any two adjacent floor
spans in the direction of the tie under consideration
Fs Fs
Ft = (20 + 4n0) ≤ 60 kN (n0 is the number of storeys)
l0
The maximum spacing of internal ties is 1.5lr.
a) Intermeshed fabric (longitudinal section)

Fs
Fs
Minimum radii and end
l0
projections
b) Layered fabric (longitudinal section)

The minimum radii for bends and length of end projections are given
in Table 12.
Tying requirements
Table 12
Minimum scheduling radii and bend allowances
At each floor and roof level an effectively continuous peripheral tie
should be provided within 1.2 m from the edge; this need not be
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

additional reinforcement. In practice, for most buildings, according to

≥ 5d
the UK National Annex to BS EN 1992, the tie should resist a tensile r P
force of 60 kN. An area of reinforcement of 138 mm2 is sufficient to
resist this force.
Nominal Minimum Minimum end projection, P
Internal ties should be provided at each floor and roof level in two size of bar, radius for
d (mm) scheduling, General (min 5d Links where bend
directions approximately at right angles. They should be effectively r (mm) straight), including < 150° (min 10d
continuous throughout their length and should be anchored to the links where bend > straight) (mm)
150° (mm)
peripheral ties at each end, unless continuing as horizontal ties to columns
8 16 115a 115a
or walls. The internal ties may, in whole or in part, be spread evenly in 10 20 120a 130
the slabs or may be grouped at or in beams, walls or other appropriate 12 24 125a 160
positions. In walls they should be within 0.5 m from the top or bottom of 16 32 130 210
floor slabs. In each direction, internal ties should be capable of resisting a 20 70 190 290
design value of tensile force Ftie,int (in kN per metre width): 25 87 240 365
32 112 305 465
Ftie,int = [(qk + gk)/7.5](lr/5)(Ft) ≥ Ft kN/m
40 140 580
where Key
(qk + gk) = sum of the average permanent and variable floor loads a The minimum end projections for smaller bars is governed by the practicalities of
bending bars.
(in kN/m2)

References
1 BRITISH STANDARDS INSTITUTION. BS EN 1992, Eurocode 2: Design of concrete structures. BSI (4 parts).
2 BRITISH STANDARDS INSTITUTION. BS 4449: Specification for carbon steel bars for the reinforcement of concrete. BSI, 2005.
3 BRITISH STANDARDS INSTITUTION. BS EN 10080: Steel for the reinforcement of concrete – Weldable reinforcing steel – General. BSI, 2005.
4 BRITISH STANDARDS INSTITUTION. BS 8666: Scheduling, dimensioning, bending and cutting of steel reinforcement for concrete – Specification. BSI, 2005.
5 INSTITUTION OF STRUCTURAL ENGINEERS/CONCRETE SOCIETY. Standard method of detailing structural concrete. ISE/CS, 2006.
6 CONSTRUCT. National structural concrete specification Construct, 4th Edition, 2010.
7 CONSTRUCT. A guide to contractor detailing of reinforcement in concrete. BCA, 1997.
8 THE CONCRETE SOCIETY. Technical report 62: Self-compacting concrete. CCIP–001. The Concrete Society, 2005.
9 BRITISH STANDARDS INSTITUTION (2008) EN 13670: Execution of concrete structures, London: BSI
10 GOODCHILD, C AND TOPLIS, P. Bar schedule dimensions: deductions for permitted deviations. The Structural Engineer, December 2013

97
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Table 13
Anchorage and lap lengths

Bond condition Reinforcement in tension, bar diameter, f (mm) Reinforcement

(see Figure 1) in compression
8 10 12 16 20 25 32 40
Concrete class C20/25
Good 270 370 480 690 910 1180 1500 2040 47f
Straight bars only
Anchorage Poor 380 520 680 990 1290 1680 2150 2920 67f
length, lbd Good 370 470 570 750 940 1180 1500 2040 47f
Other bars
Poor 530 670 810 1080 1340 1680 2150 2920 67f

50% lapped in one Good 370 510 660 970 1270 1640 2100 2860 66f

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
location (a6 = 1.4) Poor 530 730 950 1380 1810 2350 3000 4080 94f
Lap length,
l0 100% lapped Good 400 550 710 1030 1360 1760 2250 3060 70f
in one location (a6 = 1.5)
Poor 510 790 1010 1480 1940 2320 3220 4370 100f
Concrete class C25/30
Good 230 320 410 600 780 1010 1300 1760 40f
Straight bars only
Anchorage Poor 330 450 580 850 1120 1450 1850 2510 58f
length, lbd Good 320 410 490 650 810 1010 1300 1760 40f
Other bars
Poor 460 580 700 930 1160 1450 1850 2510 58f

50% lapped in one Good 320 440 570 830 1090 1420 1810 2460 57f
location (a6 = 1.4) Poor 460 630 820 1190 1560 2020 2590 3520 81f
Lap length,
l0 Good 340 470 610 890 1170 1520 1940 2640 61f
100% lapped
in one location (a6 = 1.5) Poor 490 680 870 1270 1670 2170 2770 3770 87f
Concrete class C28/35
Good 210 300 380 550 730 940 1200 1630 37f
Straight bars only
Anchorage Poor 300 420 540 790 1030 1340 1720 2330 53f
length, lbd Good 300 380 450 600 750 940 1200 1630 37f
Other bars
Poor 420 540 650 860 1070 1340 1720 2330 53f

50% lapped in one Good 300 410 530 770 1010 1320 1680 2280 52f
location (a6 = 1.4) Poor 420 590 760 1100 1450 1880 2400 3260 75f
Lap length,
l0 Good 320 440 570 830 1090 1410 1800 2450 56f
100% lapped
in one location (a6 = 1.5) Poor 450 630 810 1180 1550 2010 2570 3470 80f
Concrete class C30/37
Good 210 280 360 530 690 900 1150 1560 36f
Straight bars only
Anchorage Poor 290 400 520 750 990 1280 1640 2230 51f
length, lbd Good 290 360 430 580 720 900 1150 1560 36f
Other bars
Poor 410 520 620 820 1030 1280 1640 2230 51f

50% lapped in one Good 290 390 510 740 970 1260 1610 2180 50f
location (a6 = 1.4) Poor 410 560 720 1050 1380 1790 2290 3110 72f
Lap length,
l0 Good 310 420 540 790 1040 1350 1720 2340 54f
100% lapped
in one location (a6 = 1.5) Poor 430 600 780 1130 1480 1920 2460 3340 77f
Concrete class C32/40
Good 200 270 350 510 660 860 1100 1490 34f
Straight bars only
Anchorage Poor 280 380 500 720 950 1230 1570 2130 49f
length, lbd Good 270 350 420 550 690 860 1100 1490 34f
Other bars
Poor 390 490 590 790 980 1230 1570 2130 49f

50% lapped in one Good 270 380 490 710 930 1200 1540 2090 48f
location (a6 = 1.4) Poor 390 540 690 1010 1320 1720 2200 2980 69f
Lap length,
l0 Good 290 400 520 760 990 1290 1650 2240 51f
100% lapped
in one location (a6 = 1.5) Poor 420 570 740 1080 1420 1840 2350 3200 73f

98
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
10. Detailing

Bond condition Reinforcement in tension, bar diameter, f (mm) Reinforcement

(see Figure 1) in compression
8 10 12 16 20 25 32 40
Concrete class C35/45
Good 190 260 330 480 630 810 1040 1410 32f
Straight bars only
Anchorage Poor 260 360 470 680 890 1160 1480 2010 46f
length, lbd Good 260 330 390 520 650 810 1040 1410 32f
Other bars
Poor 370 470 560 740 930 1160 1480 2010 46f

50% lapped in one Good 260 360 460 670 870 1130 1450 1970 45f
location (a6 = 1.4) Poor 370 510 650 950 1250 1620 2070 2810 65f
Lap length,
l0 100% lapped Good 280 380 490 710 940 1210 1550 2110 48f
in one location (a6 = 1.5)
Poor 390 540 700 1020 1340 1730 2220 3010 69f
Concrete class C40/50
Good 170 230 300 440 570 740 950 1290 30f
Straight bars only
Anchorage Poor 240 330 430 620 820 1060 1350 1840 42f
length, lbd Good 240 300 360 480 600 740 950 1290 30f
Other bars
Poor 340 430 510 680 850 1060 1350 1840 42f

50% lapped in one Good 240 330 420 610 800 1040 1330 1800 41f
location (a6 = 1.4) Poor 340 460 600 870 1140 1480 1890 2570 59f
Lap length,
l0 Good 250 350 450 650 860 1110 1420 1930 44f
100% lapped
in one location (a6 = 1.5) Poor 360 500 640 930 1220 1590 2030 2760 63f
Concrete class C45/55
Good 160 220 280 400 530 690 880 1190 27f
Straight bars only
Anchorage Poor 220 310 400 580 760 980 1250 1700 39f
length, lbd Good 220 280 330 440 550 690 880 1190 27f
Other bars
Poor 310 390 470 630 780 980 1250 1700 39f

50% lapped in one Good 220 300 390 560 740 960 1230 1670 38f
location (a6 = 1.4) Poor 310 430 550 800 1060 1370 1750 2380 55f
Lap length,
l0 Good 230 320 420 600 790 1030 1310 1780 41f
100% lapped
in one location (a6 = 1.5) Poor 330 460 590 860 1130 1470 1880 2550 58f
Concrete class C50/60
Good 150 200 260 380 490 640 820 1110 25f
Straight bars only
Anchorage Poor 210 290 370 540 700 910 1170 1580 36f
length, lbd Good 220 280 330 440 550 690 880 1190 27f
Other bars
Poor 310 390 470 630 780 980 1250 1700 39f

50% lapped in one Good 220 300 390 560 740 960 1230 1670 38f
location (a6 = 1.4) Poor 310 430 550 800 1060 1370 1750 2380 55f
Lap length,
l0 Good 230 320 420 600 790 1030 1310 1780 41f
100% lapped
in one location (a6 = 1.5) Poor 330 460 590 860 1130 1470 1880 2550 58f
Notes
1 Cover to all sides ≥ 25 mm distance between bars ≥ 50mm (i.e. a2 < 1).
2 a1 = a3 = a4 = a5 = 1.0. For the beneficial effects of shape of bar, cover and confinement see Eurocode 2, Table 8.2.
3 Design stress has been taken at 435 MPa. Where the design stress in the bar at the position from where the anchorage is measured, ssd, is less than 435 MPa the figures in this
table can be factored by ssd/435. The minimum lap length id given in cl 8.7.3 of Eurocode 2.
4 The anchorage and lap lengths have been rounded up to the nearest 10 mm.
5 Where 33% of bars are lapped in one location, decrease the lap lengths for '50% lapped in one location' by a factor of 0.82.

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`--- 99
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
10. Detailing

Table 14
Sectional areas of groups of bars (mm2)

Bar size Number of bars

(mm)
1 2 3 4 5 6 7 8 9 10
8 50.3 101 151 201 251 302 352 402 452 503
10 78.5 157 236 314 393 471 550 628 707 785
12 113 226 339 452 565 679 792 905 1020 1130
16 201 402 603 804 1010 1210 1410 1610 1810 2010
20 314 628 942 1260 1570 1880 2200 2510 2830 3140
25 491 982 1470 1960 2450 2950 3440 3930 4420 4910
32 804 1610 2410 3220 4020 4830 5630 6430 7240 8040
40 1260 2510 3770 5030 6280 7540 8800 10100 11300 12600

Table 15
Sectional areas per metre width for various spacings of bars (mm2)

Bar size Spacing of bars (mm)

(mm)
75 100 125 150 175 200 225 250 275 300
8 670 503 402 335 287 251 223 201 183 168
10 1050 785 628 524 449 393 349 314 286 262
12 1510 1130 905 754 646 565 503 452 411 377
16 2680 2010 1610 1340 1150 1010 894 804 731 670
20 4190 3140 2510 2090 1800 1570 1400 1260 1140 1050
25 6540 4910 3930 3270 2800 2450 2180 1960 1780 1640
32 10700 8040 6430 5360 4600 4020 3570 3220 2920 2680
40 16800 12600 10100 8380 7180 6280 5590 5030 4570 4190

Table 16
Mass of groups of bars (kg per metre run)

Bar size Number of bars

(mm)
1 2 3 4 5 6 7 8 9 10
8 0.395 0.789 1.184 1.578 1.973 2.368 2.762 3.157 3.551 3.946
10 0.617 1.233 1.850 2.466 3.083 3.699 4.316 4.932 5.549 6.165
12 0.888 1.776 2.663 3.551 4.439 5.327 6.215 7.103 7.990 8.878
16 1.578 3.157 4.735 6.313 7.892 9.470 11.048 12.627 14.205 15.783
20 2.466 4.932 7.398 9.865 12.331 14.797 17.263 19.729 22.195 24.662
25 3.853 7.707 11.560 15.413 19.267 23.120 26.974 30.827 34.680 38.534
32 6.313 12.627 18.940 25.253 31.567 37.880 44.193 50.507 56.820 63.133
40 9.865 19.729 29.594 39.458 49.323 59.188 69.052 78.917 88.781 98.646

Table 17
Mass in kg per square metre for various spacings of bars (kg per m2)

Bar size Spacing of bars (mm)

(mm)
75 100 125 150 175 200 225 250 275 300
8 5.261 3.946 3.157 2.631 2.255 1.973 1.754 1.578 1.435 1.315
10 8.221 6.165 4.932 4.110 3.523 3.083 2.740 2.466 2.242 2.055
12 11.838 8.878 7.103 5.919 5.073 4.439 3.946 3.551 3.228 2.959
16 21.044 15.783 12.627 10.522 9.019 7.892 7.015 6.313 5.739 5.261
20 32.882 24.662 19.729 16.441 14.092 12.331 10.961 9.865 8.968 8.221
25 51.378 38.534 30.827 25.689 22.019 19.267 17.126 15.413 14.012 12.845
32 84.178 63.133 50.507 42.089 36.076 31.567 28.059 25.253 22.958 21.044
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,

40 131.528 98.646 78.917 65.764 56.369 49.323 43.843 39.458 35.871 32.882

100
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
Ahpmh]^lb`g\hg\k^m^lmkn\mnk^lnlbg`>nkh\h]^+

**' Lmkn\mnkZe_bk^]^lb`g
A S Fraser;>g`Ia=<>g`FB<>FBLmkn\m>A E K Jones ;>g`Ia=<>g`?B<> J Burridge MA CEng MIStructE MICE

Introduction
Mabl\aZim^k\ho^klma^lmkn\mnkZe_bk^]^lb`gh_\hg\k^m^lmkn\mnk^lmh
>nkh\h]^+%IZkm*+3Lmkn\mnkZe_bk^]^lb`g*%pab\apbee[^k^_^kk^]mhZlIZkm
*+makhn`ahnm'Bml^mlhnmmak^^]^lb`gf^mah]lmhZeehpma^^g`bg^^kmh
lZmbl_rma^i^k_hkfZg\^k^jnbk^f^gmlh_Zlmkn\mnk^bg_bk^3
N MZ[neZkf^mah]l
N Lbfieb_b^]\Ze\neZmbhgf^mah]l
N :]oZg\^]\Ze\neZmbhgf^mah]l

Mabl\aZim^k`bo^l`nb]Zg\^hgma^mZ[neZkZg]lbfieb_b^]f^mah]l'Ma^
Z]oZg\^]f^mah]l%pab\ak^jnbk^li^\bZeblmdghpe^]`^Zg]mhhel%Zk^hnmlb]^
ma^l\hi^h_mablin[eb\Zmbhg'?nkma^kbg_hkfZmbhg\Zg[^_hng]bg@nb]^mh
ma^Z]oZg\^]_bk^lZ_^mr^g`bg^^kbg`h_lmkn\mnk^l+':`nb]^mhlê^\mbg`ma^
ZiikhikbZm^f^mah]_hkma^]^lb`gh_ê^f^gmlbgma^_bk^\hg]bmbhgbl`bo^gbg
?b`nk^*[êhp'

Bmlahne][^ghm^]maZmma^NDGZmbhgZe:gg^q,!G:"oZen^laZo^[^^g
nl^]makhn`ahnm%bg\en]bg`pbmabgma^_hkfneZ^Zg]mZ[e^l'BgZ]]bmbhg%mabl
in[eb\Zmbhg]h^lghm\ho^kma^nl^h_\hg\k^m^\eZll^l`k^Zm^kmaZg<.)(/)%
_hkpab\ama^k^blZ]]bmbhgZe`nb]Zg\^bgIZkm*+'
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

<_]kh['
<bemY^Whji^em_d]m^_Y^\_h[h[i_ijWdY[Z[i_]dc[j^eZjeWZefj

Start

Can the Yes

tabular method conditions Use tabular method
be met?

No
No Is there an Yes
Use simplified methods acceptable solution?

Is the element a Yes Use Annex C of Part 1–2:

braced column? Buckling of columns under fire

Yes Use Annex E of Part 1–2:

Is the element a
Simplified calculation method
slab or beam?
for beams and slabs

No
Use 500o9 isotherm method No Is there an
or zone method acceptable solution?

Yes
Finish

101
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

<_]kh[(
Basic concepts Coefficient kc(yWbbem_d]\ehZ[Yh[Wi[e\Y^WhWYj[h_ij_Yijh[d]j^
(fck) of concrete
Ma^k^Zk^lhf^[Zlb\\hg\^imlpbmabgIZkm*¾+maZmZk^bgmkh]n\^]
1.0
a^k^mhZb]ng]^klmZg]bg`%iZkmb\neZker_hkma^lbfieb_b^]\Ze\neZmbhg
f^mah]l'Ma^k^bl\hglb]^kZ[erfhk^]^mZbebgMa^<hg\k^m^<^gmk^
in[eb\Zmbhg@nb]^mhma^_bk^k^lblmZg\^h_\hg\k^m^lmkn\mnk^l-' 0.8
Calcareous
aggregates

Coefficient, k c (y )
Fire types 0.6
Siliceous
aggregates
>nkh\h]^*%IZkm*+.ikhob]^lZ\ahb\^[^mp^^gghfbgZeZg]gZmnkZe
_bk^^qihlnk^\hg]bmbhgl'GhfbgZe_bk^lZk^kîk^l^gm^][r`^g^kZebl^]
0.4
_bk^\nko^l_hkmaînkihl^lh_\eZllb_b\ZmbhgZg]\hfiZkblhg[nm
ma^r[^ZkghkêZmbhglabimhmaîZkmb\neZk\aZkZ\m^kblmb\lh_ma^
[nbe]bg`ng]^k\hglb]^kZmbhg'GZmnkZe!iZkZf^mkb\"_bk^lZk^]^Zempbma 0.2
[r\Ze\neZmbhgm^\agbjn^l[Zl^]hgZ\hglb]^kZmbhgh_maîarlb\Ze
iZkZf^m^klli^\b_b\mhZiZkmb\neZk[nbe]bg`hk_bk^\hfiZkmf^gm'Ma^

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
0
fhlm\hffhgghfbgZe_bk^^qihlnk^nl^]bg]^lb`gblma^lmZg]Zk] 0 200 400 600 800 1000 1200
o
_bk^\nko^4mablblma^Zllnf^]_bk^^qihlnk^bgmabl\aZim^k' Temperature, y ( C)

<_]kh[)
Level of protection Coefficient ks(yWbbem_d]\ehZ[Yh[Wi[e\Y^WhWYj[h_ij_Yijh[d]j^fok)
Ma^k^Zk^mak^^lmZg]Zk]_bk^^qihlnk^\hg]bmbhglmaZmfZrg^^]mh[^ of tension and compression reinforcement (class N)
lZmbl_b^]!_hkbglmZg\^mh\hfierpbma[nbe]bg`k^`neZmbhgl"3 1. 0
R F^\aZgb\Zek^lblmZg\^_hkehZ][^Zkbg`
Hot-rolled tension
E Bgm^`kbmrh_l^iZkZmbhg reinforcement, e s,fi 2%
0.8
I BglneZmbhg
Cold-worked tension
reinforcement, e s,fi 2%
Coefficient, k s (y )

Ma^k^jnbk^]i^k_hkfZg\^\kbm^kbZpbee]î^g]hgma^_ng\mbhgh_ 0.6
ma^ê^f^gm%pbmaleZ[l`^g^kZeerk^jnbkbgèhZ]k^lblmZg\^Zg]_bk^ Compression
reinforcement and
lîZkZmbhg\ZiZ[bebmrpa^k^Zl\henfglfZrhgerg^^]ehZ]k^lblmZg\^' tension reinforcement,
0.4 where es,fi < 2%

Material factors
Pa^k^bmblk^jnbk^]%ma^k^lblmZg\^h_Zl^\mbhglahne][^\Ze\neZm^]% 0.2
mZdbg`ma^fZm^kbZe_Z\mhkgF%_bZl*')pbmak^li^\mmh[hmama^
ma^kfZeZg]f^\aZgb\Zeikhi^kmb^lh_ma^\hg\k^m^%k^bg_hk\^f^gmhk
0
ik^lmk^llbg`lm^^e' 0 200 400 600 800 1000 1200
o
Temperature, y ( C)

Ijh[d]j^h[ZkYj_ed <_]kh[*
Ma^lmk^g`mah_\hg\k^m^%k^bg_hk\^f^gmZg]ik^lmk^llbg`lm^^ek^]n\^l Coefficient kp(yWbbem_d]\ehZ[Yh[Wi[e\Y^WhWYj[h_ij_Yijh[d]j^
pbmabg\k^Zlbg`m^fi^kZmnk^'?hk_bk^]^lb`gmablblZ\\hngm^]_hk[r (b fpke\fh[ijh[ii_d]ij[[b
ma^nl^h_lmk^g`mak^]n\mbhg_Z\mhkl' 1.0

Bgma^\Zl^h_\hg\k^m^%ma^k^]n\mbhg_Z\mhk%d\!y"%blZ_ng\mbhgh_ Quenched and tempered

0.8 prestressing steel (bars)
ma^Z``k^`Zm^mri^Zllahpghg?b`nk^+'Lbeb\^hnlZ``k^`Zm^lln\a
ZllZg]lmhg^lZk^\hfihl^]fZbgerh_lbeb\hg]bhqb]^Zg]jnZkmsbm^l%
Coefficient, k p (y )

pabe^\Ze\Zk^hnlZ``k^`Zm^lln\aZlebf^lmhg^lZk^\hfihl^]fZbger 0.6
h_\Ze\bnf\Zk[hgZm^'Ma^k^]n\mbhg_Z\mhkl_hkk^bg_hk\bg`Zg]
ik^lmk^llbg`lm^^el%dl!y "Zg]di!y"%Zk^lahpgbg?b`nk^l,Zg]-' Cold-worked prestressing
0.4 Cold-worked steel (wires and strands)
prestressing Class A
steel (wires and
Combinations of actions strands) Class B
Pa^k^bmblk^jnbk^]_hkf^f[^kZgZerlbl%ma^^__^\mh__bk^hgZ\mbhgl 0.2
blZ\\hngm^]_hk[rZiierbg`Zk^]n\mbhg_Z\mhk%n_b%mhma^Zf[b^gm
]^lb`goZen^'Pa^k^>qik^llbhg!/'*)"h_>nkh\h]^aZl[^^gnl^]%n_b 0
bl]^_bg^]Zl3 0 200 400 600 800 1000 1200
o
Temperature, y ( C)
n_b6!@d $ c_bJd%*"(!*',.@d$*'.Jd%*" TIZkm*+>qi'!+'."V

102
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
12. Structural fire design

:llnfbg`ma^NDGZmbhgZe:gg^qoZen^lZiikhikbZm^mh>qik^llbhg
!/'*)"bg>nkh\h]âZo^[^^gnl^]%ma^gc_b6c*%*'?b`nk^.\Zgnl^] Tabular method
mhehhdnimaôZen^h_n_b Mabl]^^f^]&mh&lZmbl_r]^mZbebg`f^mah]bgL^\mbhg.h_IZkm*+nl^l
ma^ghfbgZe]blmZg\^_khfma^_Z\^h_ma^l^\mbhgmhma^Zqblh_ma^
B_>qik^llbhgl/'*)!Z"Zg]/'*)!["aZo^[^^gnl^]%ma^gma^lfZee^k k^bg_hk\^f^gm!l^^?b`nk^0"Zg]ghmma^\ho^k]blmZg\^'Ma^mZ[e^lh_
oZen^]^m^kfbg^]_khfma^_heehpbg`lahne][^nl^]_hkn_b3 Zqbl]blmZg\^Zg]fbgbfnfl^\mbhglbs^Zkîkhob]^]_hkZgnf[^kh_
n_b6!@d $c_bJd%*"(!*',.@d$*'.c)%*Jd%*" TIZkm*+>qi'!+'.Z"V f^f[^kmri^lnimhZ_bk^^qihlnkî^kbh]h_+-)fbgnm^l'

n_b6!@d $c_bJd%"(!'+.@d$'.Jd%" TIZkm*+>qi'!+'.["V

Ma^fbgbfnfk^jnbk^]Zqbl]blmZg\^%Z%]^m^kfbg^]_khfma^mZ[e^lblZ
pa^k^c)%*blZ_ng\mbhgh_nl^]^m^kfbg^]_khf;L>G*22)3+))+/% ghfbgZeoZen^%b'^'ZgZeehpZg\^_hkmhe^kZg\^l]h^lghmg^^]mh[^Z]]^]
l^^<aZim^k*_hk_nkma^k]^mZbel'=_bZelhoZkb^lbg^Z\ah_ma^Z[ho^ mhmabloZen^'Pabelm\kbm^kbZ>Zg]Bikhm^\mbhgeôêlfZr[^Z\abô^][r
^qik^llbhglZg]bl\aZkm^]bg?b`nk^/_hkoZkbhnloZen^lh_=)%*' lZmbl_rbg`ma^fbgbfnfl^\mbhgk^jnbk^f^gml%\kbm^kbhgKk^jnbk^lmaZmma^
fbgbfnfZqbl]blmZg\^k^jnbk^f^gmllahne]Zelh[^lZmbl_b^]'

Ma^bg_en^g\^h_Z``k^`Zm^mri^hgl^\mbhg[âZobhnkbg_bk^\hg]bmbhgl
IfWbb_d]
blZ\\hngm^]_hk[rma^kêZqZmbhgmaZm%pa^k^\Ze\Zk^hnlZ``k^`Zm^lZk^
Mphmri^lh_liZeebg`Zk^\hglb]^k^]bgIZkm*+3^qiehlbo^liZeebg`Zg]
nl^]%ma^fbgbfnfmab\dg^llfZr[^k^]n\^][r*)'
\hg\k^m^_Zeebg`h__ma^l^\mbhg'
Ma^mZ[neZm^]]ZmZaZl[^^g[Zl^]hgZ\kbmb\Zem^fi^kZmnk^h_.))<
Explosive spalling Zg]ZoZen^h_n_b6)'0'Ma^^q\îmbhgmhmablbl_hk\henfglZg]ehZ]&

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
Mablblngebdêrmhh\\nkpa^gma^fhblmnk^\hgm^gmh_ma^\hg\k^m^ [^Zkbg`pZeelpa^k^mableZmm^kiZkZf^m^kblkîeZ\^][rZnmbeblZmbhg
ble^llmaZg,[rp^bàm'Pa^k^mabloZen^bl^q\^^]^]%^qieb\bm\a^\dl _Z\mhkbgma^_bk^lbmnZmbhg%m_b'Ahpô^k%n_bfZr[^nl^]bglm^Z]h_m_b
!IZkm*+<e'-'.'*!.""Zk^k^jnbk^]'BmblZllnf^]maZmpa^k^Zf^f[^k ZlZ\hgl^koZmbo^lbfieb_b\Zmbhg'
aZl[^^g]^lb`g^]mhaZo^Zg^qihlnk^\eZllh_Q)hkQ<*bgZ\\hk]Zg\^
<_]kh[,
pbma>nkh\h]^+%IZkm**0%^qiehlbo^liZeebg`blngebdêrmhh\\nk%Zg]
:[j[hc_dWj_ede\nfiki_d];nfh[ii_edi($+WWdZXe\FWhj'(
mablpbeemrib\Zeer[^ma^\Zl^_hkbgm^kgZe\hg\k^m^'Bgma^mZ[neZkf^mah]%
pa^gma^Zqbl]blmZg\^mhma^fZbgk^bg_hk\^f^gmble^llmaZg0)ff 0.90
ma^ggh_nkma^k\a^\dlZk^k^jnbk^]_hkghkfZep^bàm\hg\k^m^'
0.80
Concrete falling off the section
Mrib\Zeer^qi^kb^g\^]bgmaêZmm^klmZ`^lh__bk^^qihlnk^%mablfZr[^ 0.70
c 0, 1 = 1.0 ; c 1, 1 = 0.9
Reduction factor, n fi

ik^o^gm^][r`hh]]^mZbebg`'Bg\Zl^lpa^k^ma^Zqbl]blmZg\^mhma^
0.60 c = 0.7 ; c 1, 1 = 0.7
fZbgk^bg_hk\^f^gmbl^jnZemhhk`k^Zm^kmaZg0)ff%Zg]bgma^ 0, 1

Z[l^g\^h_m^lmbg`%lnk_Z\^k^bg_hk\^f^gmpbmaZ]bZf^m^kh_Zme^Zlm 0.50 c = 0.7 ; c 1, 1 = 0.5

0, 1
-fflahne][^nl^]%liZ\^]Zm*))ff\^gmk^lhke^ll'
0.40
<_]kh[+ c 0, 1 = 0. 5 ; c 1, 1 = 0. 2
:[j[hc_dWj_ede\nfiki_d];nfh[ii_ed($+e\FWhj'(
0.30

0.90 0.20
0 0.5 1.0 1.5 2.0 2.5 3.0
Ratio,
0.80

0.70 <_]kh[-
c 1, 1 = 0.9
Reduction factor, n fi

I[Yj_edj^hek]^c[cX[hi^em_d]dec_dWbWn_iZ_ijWdY["a
0.60
c 1, 1 = 0.7

0.50
c 1, 1 = 0.5

0.40 h b b

c 1, 1 = 0.2
0.30
a a
0.20
0 0.5 1.0 1.5 2.0 2.5 3.0 a sd
Ratio, b

103
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Pa^k^ma^\kbmb\Zem^fi^kZmnk^blghm.))<%Zf^mah]blikhob]^] ma^\Zl^maZmg^bma^kf^mah]pbee[ôZeb]%manlk^jnbkbg`ma^^g`bg^^k
mhfh]b_rma^Zqbl]blmZg\^`bo^g[rma^mZ[neZkf^mah]_hkm^glbhg mhnl^Zlbfieb_b^]\Ze\neZmbhgf^mah]mh]^fhglmkZm^Z\\îmZ[bebmr'
f^f[^klZg]lbfierlniihkm^]f^f[^klbg[^g]bg`'Ma^fh]b_b\Zmbhg Ahpô^k%ZlZgZem^kgZmbo^%bgln\abglmZg\^lpa^k^ma^]^lb`gZqbZe
blZ_ng\mbhgh_ma^Zk^Zh_k^bg_hk\^f^gmikhob]^]Zg]maêhZ] _hk\^blghm`k^Zm^kmaZg)'*_\dmbf^lma^`khll\khll&l^\mbhgZeZk^Z%ma^
k^]n\mbhg_Z\mhk_hk_bkêhZ]bg`'Ma^k^]n\mbhgbl\aZkm^]bg?b`nk^1_hk f^f[^kfZr[^]^lb`g^]ZlZ[^Zf'
k^bg_hk\bg`[Zklpbmabgma^kZg`^,.)<©y\k©0))<'Bmlahne]Zelh[^
ghm^]maZmmablikhoblbhg]h^lghmZeehpma^fbgbfnf\ho^kk^jnbk^f^gml Method A
h_>nkh\h]^+%IZkm**mh[^k^]n\^]' MZ[e^*`bo^lfbgbfnfl^\mbhglbs^lZg]Zqbl]blmZg\ôZen^l_hk
oZkbhnlk^lblmZg\^mbf^lZg]nmbeblZmbhgkZmbhl!m_b"'Ma^k^lmkb\mbhglhg
?hkik^lmk^ll^]f^f[^kl%ma^\kbmb\Zem^fi^kZmnk^blZllnf^]mh ma^nl^h_F^mah]:Zk^3
[^-))<_hk[ZklZg],.)<_hkm^g]hgl'Ma^k^_hk^%bgik^lmk^ll^] N Ma^^__^\mboê^g`mah_ma^[kZ\^]\henfgbgma^_bk^\hg]bmbhg%e)%_b
f^f[^kl%ma^k^jnbk^]Zqbl]blmZg\^_khfma^mZ[e^llahne][^bg\k^Zl^] lahne][^©,f
[r*)ff_hkik^lmk^llbg`[ZklZg]*.ff_hkik^lmk^llbg`pbk^lZg] N Ma^_bklmhk]^k^\\^gmkb\bmrng]^k_bk^\hg]bmbhgllahne]lZmbl_rma^
lmkZg]l'B_bm\Zg[^]^fhglmkZm^]!nlnZeermakhnà_bk^^g`bg^^kbg`"maZm ebfbm3
maîk^lmk^llbg`lm^ê]h^lghmk^Z\ama^\kbmb\Zem^fi^kZmnk^ma^gma^
^6F)>]%_b(G>]%_b©^fZq
Z]]bmbhgZeZqbl]blmZg\^blghmk^jnbk^]'
pa^k^
Pa^k^k^bg_hk\^f^gmhkik^lmk^llbg`m^g]hglZkêZr^k^]%Z_nkma^k F)>]%_b 6 _bklmhk]^k]^lb`gfhf^gm
\a^\dblk^jnbk^]mhlahpmaZmma^mZ[neZm^]Zqbl]blmZg\^blghme^ll G>]%_b 6 ZqbZe_hk\^ng]^k_bk^\hg]bmbhgl
maZgma^Zo^kZ`^Zqbl]blmZg\^%Zf%]^m^kfbg^]_khfma^_heehpbg`3 ^fZq 6 )'*.a!hk)'*.[_hk\bk\neZkl^\mbhgl"

pa^k^ Ma^]^`k^^h_nmbeblZmbhgbgma^_bk^lbmnZmbhgbl]^_bg^][r
:lb6 ma^Zk^Zh_[Zkhkm^g]hg%ÃbÃ m_b6G>]%_b (GK]Zg]blnl^]mh]^m^kfbg^ma^\hkk^\mmZ[neZm^]oZen^'
Zb 6 ma^Zqbl]blmZg\^mh[Zkhkm^g]hgÂbÃ_khfma^g^Zk^lm ?hklbfieb\bmr%Zg]\hgl^koZmboêr%bm\Zg[^mZd^gmaZmm_b6n_b6)'0%
^qihl^]lnk_Z\^' b'^'bmblZllnf^]maZmma^\henfgk^lblmZg\^bl^jnZemhbml\ZiZ\bmrZm
Zf[b^gmnembfZmêhZ]l'
Columns
IZkm*¾+ik^l^gmlmphf^mah]l%:Zg];%pab\aZk^[hmaZ\\îmZ[e^_hk MaôZen^lbgma^mZ[e^Zk^\Ze\neZm^]mZdbgà\\6*')'Ma^NDGZmbhgZe
:gg^qmZd^la\\6)'1.Zg]mablfZr[^Z\\hngm^]_hk[r_Z\mhkbg`ma^
nl^bgma^ND'Ma^rZiiermh[kZ\^]lmkn\mnk^l4ng[kZ\^]lbmnZmbhglZk^
\Ze\neZm^]oZen^h_m_b[r)'1.¾*%hk[rnlbg`>qik^llbhg!.'0"'Ahpô^k%bm
Z]]k^ll^]eZm^kbgmabl<aZim^k'F^mah]:blma^lbfie^lmmhnl^%[nmbl
pbee[^\hgl^koZmbo^mhnl^ma^mZ[neZm^]oZen^lpbmahnmln\afh]b_b\Zmbhg'
Zelhfhk^k^lmkb\mbo^'

JWXb['
Bg[hmaf^mah]l%nl^h_ma^mZ[e^lblk^lmkb\m^][rma^ZeehpZ[e^ C_d_ckcYebkcdZ_c[di_ediWdZWn_iZ_ijWdY[\ehYebkcdim_j^
^\\^gmkb\bmrZg]^__^\mbo^e^g`malh_ma^\henfgl'Bglhf^bglmZg\^l% h[YjWd]kbWhehY_hYkbWhi[Yj_edi¸C[j^eZ7
_hk^qZfie^ma^\henfgllniihkmbg`ma^nii^kfhlm_ehhk%bmfZr[^ Standard Minimum dimensions (mm)
fire Column width bmin%Wn_iZ_ijWdY["a, of the
<_]kh[. resistance main bars
H[ZkYj_ed_dWn_iZ_ijWdY["a"Z[f[dZ_d]edWh[We\ij[[bfhel_Z[Z 9ebkcd[nfei[Zedceh[j^Wded[i_Z[ ;nfei[Z
on one side
0 mfi = 0.2 mfi3&$+ mfi3&$- mfi3&$-

2 K,) +))(+. +))(+. +))(,+ *..(+.

n fi = 0.7 ,))(+0
4
Reduction in axis distance D a (mm)

K/) +))(+. +))(,/ +.)(-/ *..(+.

6 ,))(,* ,.)(-)
n fi = 0.5 +))(,* ,))(-. ,.)(., *..(+.
8
K2)
,))(+. -))(,1 -.)(-)a
10
K*+) +.)(-) ,.)(-.a ,.)(.0a *0.(,.
12
,.)(,. -.)(-) -.)(.*a
14
K*1) ,.)(-.a ,.)(/,a -.)(0)a +,)(..
16
n fi = 0.2
18 K+-) ,.)(/*a -.)(0.a - +2.(0)
Key
20 aFbgbfnf1[Zkl'
0.5 0.6 0.7 0.8 0.9 1.0
Note
Ratio, As,req / A ?hkik^lmk^ll^]\henfglZqbl]blmZg\^lahne][^bg\k^Zl^]¾l^^m^qm'

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

104
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
12. Structural fire design

Method B Walls
MZ[e^+`bo^lfbgbfnfl^\mbhglbs^lZg]Zqbl]blmZg\ôZen^l_hk PZeelZk^\Zm^`hkbl^]bgmhghg&ehZ][^Zkbg`%ehZ][^Zkbg`%Zg]_bk^
oZkbhnlk^lblmZg\^mbf^lZg]nmbeblZmbhgZg]k^lblmZg\^kZmbhl'Ma^ pZeel'?bk^pZeelaZo^mh\hfierpbmabfiZ\mk^lblmZg\^\kbm^kbZ':l
k^lmkb\mbhglhgma^nl^h_F^mah];Zk^3 mabl\Zm^`hkblZmbhgblmrib\Zeerghmnl^]bgma^ND%_bk^pZeelZk^ghm
N Ma^le^g]^kg^llh_ma^\henfgng]^k_bk^\hg]bmbhgllahne][^ \hglb]^k^]Zgr_nkma^ka^k^'
l_b6e)%_b(b©,)pa^k^bblma^fbgbfnfkZ]bnlh_bg^kmbZ'
N Ma^_bklmhk]^k^\\^gmkb\bmrng]^k_bk^\hg]bmbhgllahne]lZmbl_r ?hkZeemri^l%ZebfbmZmbhgblieZ\^]hgma^kZmbhh_\e^Zka^bàmmh
maêbfbm3 mab\dg^ll%e)(m©-)%mhZohb]^q\^llbo^ma^kfZe]^_hkfZmbhge^Z]bg`mh
^6F)>]%_b(G)>]%_b©^fZq _Zbenk^h_bgm^`kbmr[^mp^^gpZeeZg]leZ['Ahpô^k%_hkZee[nmma^mabgg^lm
h_pZeel%mablebfbmblngebdêrmh[^k^Z\a^]bgmrib\ZeZiieb\Zmbhgl'
pa^k^
^fZq6*))ff
?hkghg&ehZ][^Zkbg`pZeel hgerma^kfZeZg](hkbgm^`kbmr\kbm^kbZ
^([ ©)'+.
!BZg]>"g^^]mh[^f^mZg]fbgbfnfmab\dg^llZehg^`ho^kglma^
[ 6fbgbfnf\henfg]bf^glbhg
Z]^jnZ\rbgma^_bkêbfbmlmZm^%b'^'gh\a^\dblk^jnbk^]hgma^Zqbl
MaêhZ]eôêZmghkfZem^fi^kZmnk^\hg]bmbhgl%g%blnl^]bgma^
]blmZg\^'?hkehZ][^Zkbg`pZeelZfbgbfnfpZeemab\dg^ll%Zg]Zqbl
]^m^kfbgZmbhgh_ma^fbgbfnfoZen^l'<hgl^koZmboêr%bmfZr[^
]blmZg\^mhma^k^bg_hk\^f^gm%fnlm[îkhob]^]'Ma^fbgbfnfoZen^l
Zllnf^]maZmg6)'0'PabelmmablZllnfimbhgfZr[^h_nl^bgbgbmbZe
_hk[hmamri^lZk^`bo^gbgMZ[e^,'Ghm^maZmmablmZ[e^fZrZelh[^
\hg\îm]^lb`g%lb`gb_b\Zgmk^]n\mbhglbgma^fbgbfnfl^\mbhglbs^
nl^]_hkieZbg\hg\k^m^pZeel'
Zg]Zqbl]blmZg\^_hkZ`bo^g_bk^k^lblmZg\î^kbh]fZr[^Z\abô^][r
\Ze\neZmbg`g^qieb\bmer_khf3
8[Wci
g6G)>]%_b(T)'0!:\_\]$:l_r]"V'
Fbgbfnfl^\mbhglbs^lZg]Zqbl]blmZg\^lmhk^bg_hk\^f^gm_hk[^Zfl
Zk^lahpgbgMZ[e^-'Bgnlbg`ma^mZ[neZkf^mah]%ma^_heehpbg`
Ghm^maZmbgma^mZ[e^ma^f^\aZgb\Zek^bg_hk\^f^gmkZmbh%w%blhg^h_
Zllnfimbhgl(k^lmkb\mbhglZk^fZ]^3
ma^k^jnbk^]iZkZf^m^kl'Bg>nkh\h]^+%IZkm**,% Z\hgl^koZmbo^
N Ma^l^\mbhgbl^qihl^]hgmak^^lb]^lpbmama^nii^klnk_Z\^
oZen^bgma^]^m^kfbgZmbhgh_ebfbmbg`le^g]^kg^ll_hkma^\henfgbl
Zllnf^]mh[^bglneZm^]'Ahpô^k%pa^k^Zeelnk_Z\^lZk^^qihl^]
)'*'?hkZ\eZll<,)(,0\hg\k^m^mablkîk^l^gml)'-k^bg_hk\^f^gm%
mh_bk^%ma^mZ[e^lfZrlmbee[^nl^][nmpbmaZ]]bmbhgZek^lmkb\mbhgl
pa^k^Zlpa^gw 6*')%ma^\henfgphne]k^jnbk^-k^bg_hk\^f^gm'
ieZ\^]hgma^fbgbfnfl^\mbhglbs^'
:]]bmbhgZebg_hkfZmbhgbl`bo^gbg:gg^q<h_IZkm*&+'

Table 2
C_d_ckcYebkcdZ_c[di_ediWdZWn_iZ_ijWdY[\ehYebkcdim_j^h[YjWd]kbWhehY_hYkbWhi[Yj_edi¸C[j^eZ8

Standard fire resistance Mechanical Minimum dimensions (mm). Column width bmin%Wn_iZ_ijWdY["a
reinforcement ratio, w n3&$'+ n3&$) n3&$+ n3&$-
K,) )'*)) *.)(+.a *.)(+.a +))(,)3+.)(+.a ,))(,)3,.)(+.a
)'.)) *.)(+.a *.)(+.a *.)(+.a +))(,)3+.)(+.a
*'))) *.)(+.a *.)(+.a *.)(+.a +))(,)3,))(+.a
K/) )'*)) *.)(,)3+))(+.a +))(-)3,))(+.a ,))(-)3.))(+.a .))(+.a --`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

)'.)) .)(+.a .)(,.3+))(+.a +.)(,.3,.)(+.a ,.)(-)3..)(+.a

*'))) *.)(+.a *.)(,)3+))(+.a +))(-)3-))(+.a ,))(.)3/))(,)
K2) )'*)) +))(-)3+.)(+.a ,))(-)3-))(+.a .))(.)3..)(+.a ..)(-)3/))(+.a
)'.)) *.)(,.3+))(+.a +))(-.3,))(+.a ,))(-.3..)(+.a .))(.)3/))(-)
*'))) +))(+.a +))(-)3,))(+.a +.)(-)3..)(+.a .))(.)3/))(-.
K*+) )'*)) +.)(.)3,.)(+.a -))(.)3..)(+.a ..)(+.a ..)(/)3/))(-.
)'.)) +))(-.3,))(+.a ,))(-.3..)(+.a -.)(.)3/))(+.a .))(/)3/))(.)
*'))) +))(-)3+.)(+.a +.)(.)3-))(+.a -.)(-.3/))(,) /))(/)
K*1) )'*)) -))(.)3.))(+.a .))(/)3..)(+.a ..)(/)3/))(,) b

)'.)) ,))(-.3-.)(+.a -.)(.)3/))(+.a .))(/)3/))(.) /))(0.

*'))) ,))(,.3-))(+.a -.)(.)3..)(+.a .))(/)3/))(-. b

K+-) )'*)) .))(/)3..)(+.a ..)(-)3/))(+.a /))(0. b

)'.)) -.)(-.3.))(+.a ..)(..3/))(+.a /))(0) b

*'))) -))(-.3.))(+.a .))(-)3/))(,) /))(/) b

Key
aGhkfZeerma^\ho^kk^jnbk^][r;L>G*22+¾*¾*pbee\hgmkhe'
bK^jnbk^lpb]ma`k^Zm^kmaZg/))ff'IZkmb\neZkZll^llf^gm_hk[n\debg`blk^jnbk^]'

105
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

N Maîkh_be^lbg?b`nk^2Zk^k^_^k^g\^]bgIZkm*+_hkma^mZ[neZk +)k^]blmkb[nmbhgZg]%b_nl^]%phne]k^jnbk^ma^lbfierlniihkm^]
f^mah]'Bghma^kbglmZg\^lln\aZlE&[^Zflhk_hkghg&lmZg]Zk] Zllnfimbhgmh[^Z]him^]'
l^\mbhglaZi^l%^g`bg^^kbg`cn]`^f^gmlahne][^nl^]bg N :]]bmbhgZe\a^\dlZk^k^jnbk^]_hkma^_bklmbgm^kgZelniihkmlh_
]^m^kfbgbg`ma^Ziieb\Z[bebmrh_ma^mZ[e^l' \hgmbgnhnlB&[^ZflkêZmbg`mhihllb[e^_Zbenk^f^\aZgblflZm_bk^
N :]]bmbhgZeebfbmlZk^Ziieb^]mhma^fbgbfnfZqbl]blmZg\^_hk k^lblmZg\î^kbh]lh_*+)fbgnm^lZg]Z[ho^'
\hkg^k[Zkl'
N ?hk\hgmbgnhnl[^Zfl%b_k^]blmkb[nmbhg^q\^^]l*.bgma^ Pa^k^ma^l^\mbhgblik^lmk^ll^]%iZkmb\neZkZmm^gmbhglahne][îZb]
Zf[b^gm\hg]bmbhg%ma^mZ[e^l_hklbfierlniihkm^]l^\mbhgllahne] mhma^fh]b_b\Zmbhgk^jnbk^]mhma^Zqbl]blmZg\^h_maîk^lmk^ll^]
[^nl^]nge^llma^fhf^gm\ZiZ\bmrbl^qieb\bmer\a^\d^]':l^\hg] ê^f^gml%Zl]bl\nll^]bgma^bgmkh]n\mbhgmhma^mZ[neZkf^mah]'
bfieb\Zmbhgh_mablebfbmblmaZmlmZg]Zk]mZ[e^lh_[^g]bg`fhf^gm
Zg]la^Zk\h^__b\b^gml%ln\aZlmahl^bgma^FZgnZe_hkma^]^lb`gh_ ?hk\hgmbgnhnl[^Zfl%\nkmZbef^gmkne^lZk^`bo^g_hkma^mhik^bg_hk\^f^gm
h_l^\mbhglbg_bk^'Ma^mhik^bg_hk\^f^gmlahne]^qm^g])',e^___khfma^
\hg\k^m^[nbe]bg`lmkn\mnk^lmh>nkh\h]^+1%Zk^mrib\Zeer[Zl^]hg
\^gmkêbg^h_ma^lniihkmpbmama^k^jnbk^]Zk^Z[^bg`Zeehp^]mhoZkrbg
Z\\hk]Zg\^pbma>G*22+&*&+>qi!.'**"!ZlbeenlmkZm^]bg?b`nk^*)"'
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

JWXb[)
Minimum wall thicknesses for walls :l%k^j!q"6:l%k^j!)"!*+'.q(e^__"
Standard Non- BeWZX[Wh_d]h[_d\ehY[ZYedYh[j[mWbbi
pa^k^
fire beWZX[Wh_d] Minimum dimensions (mm)
resistance wall MWbbj^_Yad[ii%Wn_iZ_ijWdY["a q 6 ]blmZg\^_khfma^\^gmk^ebg^h_ma^lniihkm
thickness mfi3&$)+ mfi3&$- :l%k^j!q" 6 fbgbfnfZk^Zh_mhik^bg_hk\^f^gmk^jnbk^]Zm
(mm)
Number of sides of Number of sides of ]blmZg\^q_khfma^lniihkm[nmghme^llmaZgma^
mWbb[nfei[Z mWbb[nfei[Z fbgbfnfZeehp^]_khf>nkh\h]^+%IZkm**
One Two One Two :l%k^j!)" 6 ma^Zk^Zh_mhik^bg_hk\^f^gmk^jnbk^]ho^kma^
K>B,) /)b *))(*)b *+)(*)b *+)(*)b *+)(*)b
lniihkmbgZf[b^gm]^lb`g
K>B/) 1)b **)(*)b *+)(*)b *,)(*)b *-)(*)b
e^__ 6 ^__^\mbo^e^g`mah_ma^liZg
K>B2) *))b *+)(+)b *-)(*)b *-)(+. *0)(+.
K>B*+) *+)b *.)(+. */)(+. */)(,. ++)(,.
K>B*1) *.)b *1)(-) +))(-. +*)(.) +0)(.. B_)',e^__blln[lmbmnm^]bgmhma^Z[ho^%ma^Zk^Zh_k^bg_hk\^f^gmpa^k^
K>B+-) *0.b +,)(.. +.)(.. +0)(/) ,.)(/) k^jnbk^]]khilmh+.h_maZmk^jnbk^]Zmma^lniihkm'Bglhf^\Zl^l%
Key mabl\nkmZbef^gme^g`mafZr[^fhk^hg^khnlmaZgmaZm]^m^kfbg^]_khf
aÂKÃ^qihlnk^\hg]bmbhgghmZiieb\Z[e^mhghg&ehZ][^Zkbg`pZeel
lhf^lbfie^]^mZbebg`kne^lpabelmma^lbfieb_b^]]^mZbebg`kne^lik^l^gm^]
bGhkfZeerma^\ho^kk^jnbk^][r;L>G*22+¾*¾*pbee\hgmkhe'
bg<aZim^k*)%pbeek^lnembgZlZ_^]^mZbe_hklmZg]Zk]\Zl^l'

JWXb[*
C_d_ckcZ_c[di_edWdZWn_iZ_ijWdY[i\ehYedj_dkekiX[WcicWZ[m_j^h[_d\ehY[ZWdZfh[ijh[ii[ZYedYh[j[

Standard fire Minimum dimensions (mm)

resistance Simply supported beams Continuous beams
Possible combinations of a and bmin where a is the Web Possible combinations of a and bmin where a is the Web
Wl[hW][Wn_iZ_ijWdY[WdZbmin is the width of beam thickness bw Wl[hW][Wn_iZ_ijWdY[WdZbmin is the width of beam thickness bw
' 2 ) * + 6 - . 9 '&
K,) [fbg 1) *+) */) +)) 1) 1) */) 1)
Z +. +) *.a *.a *.a *+a
K/) [fbg *+) */) +)) ,)) *)) *+) +)) *))
Z -) ,. ,) +. +. *+a
K2) [fbg *.) +)) ,)) -)) **) *.) +.) 110
Z .. -. -) ,. ,. +.
K*+) [fbg +)) +-) ,)) .)) *,) +)) ,)) -.) .)) 130
Z /. /) .. .) -. ,. ,. ,)
K*1) [fbg +-) ,)) -)) /)) *.) +-) -)) ..) /)) 150
Z 1) 0) /. /) /) .) .) -)
K+-) [fbg +1) ,.) .)) 0)) *0) +1) .)) /.) 0)) 170
Z 2) 1) 0. 0) 0. /) /) .)
Key
aGhkfZeerma^\ho^kk^jnbk^][r;L>G*22+¾*¾*pbee\hgmkhe
Notes
'?hkik^lmk^ll^]\henfglZqbl]blmZg\^lahne][^bg\k^Zl^]¾l^^m^qm'
2al]blma^Zqbl]blmZg\^mhma^lb]^h_[^Zf_hkma^\hkg^k[Zkl!hkm^g]hghkpbk^"h_[^Zflpbmahgerhg^eZr^kh_k^bg_hk\^f^gm'al]6a$*)ff%nge^llma^oZen^lh_[fbgZk^`k^Zm^k
maZgmaZm`bo^gbg\henfg,_hklbfierlniihkm^][^Zflhk\henfg1_hk\hgmbgnhnl[^Zfl%pa^gghbg\k^Zl^blk^jnbk^]'

106
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
12. Structural fire design

Tensile members N Fbgbfnfg^`Zmbo^k^bg_hk\^f^gm^jnZemh)'.h_ma^`khll

Ma^mZ[neZm^]]ZmZ_hk[^ZflfZr[^nl^]_hkm^glbe^f^f[^klpbma l^\mbhgZk^Zlahne][îkhob]^]nge^llahm&khee^]k^bg_hk\^f^gm
ma^_heehpbg`k^lmkb\mbhgl3 aZl[^^gnl^]%k^lmkZbgmblikhob]^]Zmma^^g]lniihkmlh_mph&
liZgleZ[l%Zg]mkZglo^kl^]blmkb[nmbhgh_ehZ]blZ\\hngm^]_hk'
N Ma^`khll\khll&l^\mbhgZeZk^Zlahne]ghm[ê^llmaZg+[fbg
pa^k^[fbgblma^fbgbfnfZeehpZ[e^l^\mbhgpb]mamZd^g_khfma^
Bgma^NDmaîkh\nk^f^gmh_k^bg_hk\^f^gm]h^lghmghkfZeer
mZ[neZm^]]ZmZ'
Zeehpmaîkh]n\mbhgf^mah]mh[^li^\b_b^]'@^g^kZeer%<eZll:
N Pa^k^maêhZ][^Zkbg`\ZiZ\bmrblk^]n\^][r^q\^llbo^êhg`Zmbhg%
k^bg_hk\^f^gmbl\he]phkd^]Zg]<eZll;k^bg_hk\^f^gmblahmkhee^]%
IZkm*+`bo^l`nb]Zg\^mhZ]]k^llmabl'
[nmbmblihllb[e^mh_hkf<eZll;k^bg_hk\^f^gm[r\he]phkdbg`'
:mik^l^gm<eZll<k^bg_hk\^f^gmlniieb^]bgma^NDblahmkhee^]
Slabs Zg]ma^k^_hk^\Zg[^li^\b_b^]lhmaZmma^fbgbfnfk^bg_hk\^f^gm
OZkbhnl_hkflh_leZ[Zk^\hglb]^k^]3lbfierlniihkm^]%\hgmbgnhnl% k^jnbk^]Z[ho^g^^]ghm[îkhob]^]'
mph&pZr%_eZm%Zg]kb[[^]%Zg]mZ[e^lZkîkhob]^]_hk^Z\a':lpbma
hma^kf^f[^kmri^l%Zgnf[^kh_k^lmkb\mbhglZk^Ziieb^]bg^Z\a\Zl^4 Ma^]^mZbebg`blln^lkêZmbg`mhah``bg`k^bg_hk\^f^gmbg\hgmbgnhnl
ma^l^Zk^]^l\kb[^][êhp' leZ[lZk^ma^lZf^Zlmahl^]^l\kb[^]ikôbhnler_hk\hgmbgnhnl[^Zfl'

Simply supported slabs Two-way slabs

MZ[e^.blikhob]^]_hklbfierlniihkm^]f^f[^klpbmaghli^\bZe Ma^mph&pZr\hg\îmZiieb^lmh[hmalbfierlniihkm^]Zg]
ikhoblbhgl(k^lmkb\mbhgl' \hgmbgnhnlleZ[mri^l'BgZ]]bmbhgmhma^\hff^gml_hk\hgmbgnhnl
leZ[lfZ]^Z[ho^%Zqbl]blmZg\^mhma^k^bg_hk\^f^gm%a%blmZd^gZl
Continuous slabs ma^]blmZg\^_khfma^lnk_Z\^mhma^Zqblh_ma^hnm^kfhlmeZr^kh_
<hgmbgnhnlleZ[lfZr[^mk^Zm^]Zlmph&pZrliZggbg`leZ[lpa^k^ k^bg_hk\^f^gm'
er(eq©*'.Zl`bo^gbgMZ[e^.'Ma^_heehpbg`\hg]bmbhgllahne][^f^m3
N ?hk\hgmbgnhnlleZ[l%b_k^]blmkb[nmbhg^q\^^]l*.bgma^Zf[b^gm Ma^^g`bg^^klahne]ghm^maZmma^\hgo^gmbhgbgMZ[e^.%pa^k^ma^
\hg]bmbhg%ma^mZ[e^l_hklbfierlniihkm^]l^\mbhgllahne][^nl^] kêZmbhglabi_hkliZglerªeqblma^hiihlbm^h_maZmbg>nkh\h]^+%
nge^llfhf^gm\ZiZ\bmrbl^qieb\bmer\a^\d^]' IZkm**_hk_eZmleZ[lpa^kêqªer'

<_]kh[/
:[\_d_j_ede\Z_c[di_edi\ehZ_\\[h[djjof[ie\X[Wci[Yj_ed JWXb[+
C_d_ckcZ_c[di_ediWdZWn_iZ_ijWdY[i\ehh[_d\ehY[ZWdZ
prestressed solid slabs
Standard fire Minimum dimensions (mm)
resistance One-way Jme#mWoifWdd_d]ibWXa Flat slab
bw
ifWdd_d]
slab ly/ln )'$+ '$+2ly/ln ) 2 d )'+c d4'+c

b b b K>B,) al /) /) /) .) .)

(a) Constant width (b) Variable width (c) I -Section Z *)b *)b *)b *)b *)b
K>B/) al 1) 1) 1) *1) *1)

<_]kh['& Z +) )b .b *.b +)

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

;dl[bef[e\h[i_ij_d]X[dZ_d]cec[djiel[hikffehji\eh\_h[YedZ_j_edi K>B2) al )) )) *)) +)) +))

Z ,) *.b +) +. ,)
0.3 l eff 0.4 l eff 0.3 l eff
K>B*+) al *+) *+) *+) +)) +))
Z -) +) +. ,. -)
BM from Exp. (5.11)
K>B*1) al *.) *.) *.) +)) +))
Z .. ,) -) -. ..
K>B+-) al *0. *0. *0. +)) +))
Z /. -) .) .) /.
Key
BM in fire location
aMa^m^kfmphpZrleZ[lkêZm^lmhleZ[llniihkm^]ZmZee_hnk^]`^l'B_mablblghmma^\Zl^
ma^rlahne][^mk^Zm^]Zlhg^&pZrliZggbg`leZ[l'
bGhkfZeerma^\ho^kk^jnbk^][r;L>G*22+¾*¾*pbee\hgmkhe'
BM when cdblma^k^]blmkb[nmbhgkZmbh'
t =0
Notes
Design BM
according to 'eqZg]erZk^ma^liZglh_Zmph&pZrleZ[!mph]bk^\mbhglZmkbàmZgè^l"pa^kêrblma^
BS EN 1992–1–1 ehg`^kliZg'
2 ?hkik^lmk^ll^]\henfglZqbl]blmZg\^lahne][^bg\k^Zl^]¾l^^m^qm'

107
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Flat slabs Ma^\h]b_b^]\Ze\neZmbhgf^mah]lZg]ma^bkZllh\bZm^]Zgg^q^lbg

?hk_eZmleZ[l%MZ[e^.fZr[^nl^]':me^Zlm+)h_ma^mhmZemhi IZkm*+Zk^3
k^bg_hk\^f^gmbg^Z\a]bk^\mbhg!:m"lahne][^ieZ\^]ho^kma^ N Lbfieb_b^]\Ze\neZmbhgf^mah]_hk[^ZflZg]leZ[l:gg^q>
lniihkmlbgma^\henfglmkbiZg][^\hgmbgnhnlho^kma^_neeliZg'
N .))<blhma^kff^mah]!lmZg]Zk]hkiZkZf^mkb\_bk^l":gg^q;'*

Ribbed slabs N Shg^f^mah]!lmZg]Zk]_bk^lhger"3IZkm*+k^\hff^g]lmabl

Ma^kne^l_hk[^ZflZg]\hgmbgnhnlleZ[llahne][^nl^]bgma^ blik^_^kk^]pa^k^lfZeel^\mbhglhkle^g]^k\henfglZk^[^bg`
ôZenZmbhgh_hg^&pZrkb[[^]leZ[l'?hkmph&pZrliZggbg`kb[[^]leZ[l% \hglb]^k^]:gg^q;'+'!Mablf^mah]blghmbg\en]^]bgmabl\aZim^k"
ma^bg_hkfZmbhgbgMZ[e^/blikhob]^]pbmamaêbfbmZmbhgmhma^bknl^
N F^mah]_hkma^ZgZerlblh_\henfglpbmalb`gb_b\Zgml^\hg]hk]^k
[^bg`maZmmaêhZ]bg`blik^]hfbgZgmerngb_hkfer]blmkb[nm^]'
^__^\ml:gg^q;',

:lpbma[^Zfl%bgZee\Zl^lpa^k^ma^l^\mbhgblik^lmk^ll^]%iZkmb\neZk
Ahpô^k%[^_hk^lê^\mbg`Zgrh_ma^Z[ho^f^mah]l%bmblbfihkmZgm
Zmm^gmbhglahne][îZb]mhma^fh]b_b\Zmbhgk^jnbk^]mhma^Zqbl
mhghm^maZmma^rZ]]k^ll_e^qnk^hgerpbmala^ZkZg]mhklbhg[^bg`
]blmZg\^h_maîk^lmk^ll^]ê^f^gml%ZlZek^Z]r]bl\nll^]bgma^
bgmkh]n\mbhgmhma^mZ[neZkf^mah]' \ho^k^]lîZkZmêreZm^kbgmabl<aZim^k'

Simplified calculation method for beams

Simplified calculation and slabs
Mablf^mah]%`bo^gbg:gg^q>h_IZkm*¾+%blZg^qm^glbhgmhma^
methods mZ[neZkf^mah]Zg]fZr[^nl^]bgma^]^lb`gh_[^ZflZg]leZ[l
pa^k^maêhZ]blik^]hfbgZgmerngb_hkfer]blmkb[nm^]Zg]%_hk
?hnklbfieb_b^]\Ze\neZmbhgf^mah]lZkîk^l^gm^]bgIZkm*&+'Ma^_bklm
\hgmbgnhnlf^f[^kl%maêôêh_k^]blmkb[nmbhg]h^lghm^q\^^]
h_ma^l^blZlbfieb_b^]\Ze\neZmbhgf^mah]li^\b_b\Zeer_hk[^ZflZg]
*.'?hkabà^keôêlh_k^]blmkb[nmbhg%ma^fhf^gm\ZiZ\bmrZmma^
leZ[l'Bgma^hma^kf^mah]l%Zlbfieb_b^]\khll&l^\mbhg\Ze\neZmbhgblnl^]
lniihkmlfnlm[^\a^\d^][^_hk^mablZiikhZ\afZr[^Ziieb^]'
mh]^m^kfbg^ma^_e^qnkZek^lblmZg\^h_ma^l^\mbhgbgma^_bk^\hg]bmbhg%
Zg]mablbl\hfiZk^]pbmama^^__^\mh_Z\mbhglbgma^_bk^lbmnZmbhg'
Mablf^mah]ikhob]^lZf^Zglh_\a^\dbg`pa^ma^kZk^]n\^]Zqbl
Table 6 ]blmZg\^_khfmaZm]^m^kfbg^]bgma^mZ[neZkf^mah]\Zg[^cnlmb_b^]
C_d_ckcZ_c[di_ediWdZWn_iZ_ijWdY[\ehjme#mWoifWdd_d]"i_cfbo [rZfhk^]^mZbe^]^qZfbgZmbhgh_ma^_e^qnkZe\ZiZ\bmrh_ma^l^\mbhg'
supported ribbed slabs in reinforced or prestressed concrete
Ahpô^k%ghk^]n\mbhgfZr[^fZ]^mhma^l^\mbhglbs^]^m^kfbg^]

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
Standard fire Minimum dimensions (mm) _khfma^mZ[neZkf^mah]'
resistance
Possible combinations of width of Slab thickness
ribs bminWdZWn_iZ_ijWdY[a hsWdZWn_i Ma^ZiikhZ\ablmh\a^\dmaZmma^]^lb`gfhf^gmbg_bk^bl^jnZemhhk
distance a in
Simply supported 7jb[Wijed[[Z][ \bWd][ e^llmaZgma^]^lb`gk^lblmZg\^bg_bk^%b'^'F>]%_b©FK]%_b'Ma^m^kfF>]%_b
restrained bl]^_bg^]Zl3

[fbg F>]%_b6p>]%_be^__+(1
K>B,) 1) 1) al61)
Z *.a *)a Z 6*)a pa^k^
K>B/) [fbg *)) *+) ª+)) *)) *+) ª+)) al61) p>]%_b 6 ngb_hkfer]blmkb[nm^]ehZ]!dG(f"ng]^k_bk^\hg]bmbhgl'
Z ,. +. *.a +. *.a *)a Z 6*)a 6 n_bp>]
K>B2) [fbg *+) */) ª+.) *+) */) ª+.) al6*))
n_b 6 k^]n\mbhg_Z\mhk!l^^Â\hf[bgZmbhglh_Z\mbhglÃl^\mbhg
Z
hgiZ`^+"
-. -) ,) ,. +. *.a Z 6*.a
p>] 6 ngb_hkfer]blmkb[nm^]ehZ]!dG(f"ng]^kZf[b^gm
K>B*+) [fbg */) *2) ª,)) */) *2) ª,)) al6*+)
\hg]bmbhgl
Z /) .. -) -. -) ,) Z 6+)
e^__ 6 ^__^\mboê^g`mah_[^ZfhkleZ[
K>B*1) [fbg ++) +/) ª-*) ,*) /)) al6*.)
Z 0. 0) /) /) .) Z 6,) =^m^kfbgZmbhgh_ma^]^lb`gk^lblmZg\^Zg]hma^k\a^\dl]î^g]hg
K>B+-) [fbg +1) ,.) ª.)) -.) 0)) al6*0. pa^ma^kma^f^f[^kbllbfierlniihkm^]hk\hgmbgnhnl':_ehp\aZkm
Z 2) 0. 0) 0) /) Z 6-) h_ma^]^lb`gikh\^llblik^l^gm^]bg?b`nk^**'
Key
aGhkfZeerma^\ho^kk^jnbk^][r;L>G*22+**pbee\hgmkhe'
Simply supported members
Notes
Ma^]^lb`gk^lblmZg\^ng]^k_bkêhZ]bg`bl]^m^kfbg^]_khfma^
'?hkik^lmk^ll^]\henfglZqbl]blmZg\^lahne][^bg\k^Zl^]¾l^^m^qm'
_heehpbg`^qik^llbhg3
2 Zl]blma^Zqbl]blmZg\^mhma^lb]^h_[^Zf_hkma^\hkg^k[Zkl!hkm^g]hghkpbk^"
h_[^ZflpbmahgerhgêZr^kh_k^bg_hk\^f^gm'Zl]6Z$*)ff' FK]%_b6!gl(gl%_b"dl!y"F>]!:l%ikho(:l%k^j"

108
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
12. Structural fire design

pa^k^ :l[^_hk^%bgZee\Zl^lpa^k^ma^l^\mbhgblik^lmk^ll^]%iZkmb\neZk
gl 6 iZkmbZefZm^kbZe_Z\mhk_hklm^êZmZf[b^gmm^fi^kZmnk^l Zmm^gmbhglahne][îZb]mhma^fh]b_b\Zmbhgk^jnbk^]mhma^Zqbl
gl%_b 6 iZkmbZefZm^kbZe_Z\mhk_hklm^êng]^k_bk^\hg]bmbhgl ]blmZg\^h_maîk^lmk^ll^]ê^f^gml%ZlZek^Z]r]bl\nll^]bgma^
dl!y " 6 lmk^g`mak^]n\mbhgZiieb^]mhlm^ê_hkZ`bo^g bgmkh]n\mbhgmhma^mZ[neZkf^mah]'
m^fi^kZmnk^!y"ng]^kma^k^jnbk^]_bk^k^lblmZg\^
F>] 6 ]^lb`gfhf^gm_hkZf[b^gm]^lb`g Ma^\nkmZbef^gme^g`mak^jnbk^]ng]^k_bk^\hg]bmbhglfZr[^`k^Zm^k
:l%ikho6 \khll&l^\mbhgZeZk^Zh_m^glbhgk^bg_hk\^f^gmikhob]^] maZgmaê^g`ma]^m^kfbg^]bg>nkh\h]^+%IZkm**Zg]lahne][^\a^\d^]'
:l%k^j 6 \khll&l^\mbhgZeZk^Zh_m^glbhgk^bg_hk\^f^gmk^jnbk^]
+&&9_iej^[hcc[jêZ
Ma^kZmbh:l%ikho(:l%k^jlahne]ghm[^mZd^g`k^Zm^kmaZg*','Ma^ Bgma^blhma^kff^mah]%\hg\k^m^ZmZm^fi^kZmnk^Z[ho^.))<bl
\h^__b\b^gmdl!y"fZr[^]^m^kfbg^]_khf?b`nk^*+'Ghm^mablblZ g^è^\m^]bgma^\Ze\neZmbhgh_l^\mbhgk^lblmZg\^%pabelm\hg\k^m^Zmhk[êhp
lbfieb_b\Zmbhgh_?b`nk^,%_hknl^pbmama^mZ[neZkf^mah]Zg]:gg^q>' .))<blZllnf^]mhk^mZbgbml_nee%Zf[b^gmm^fi^kZmnk^lmk^g`ma'Bg
IZkm*¾+ma^f^mah]blbeenlmkZm^]pbmak^_^k^g\^mhk^\mZg`neZkl^\mbhgl'
Continuous members
Bgma^_bk^\hg]bmbhg%IZkm*+Zeehplfhf^gmk^]blmkb[nmbhg_khf Manl%ma^\Ze\neZmbhgikh\^llblmh_bklm\a^\dmaZmma^l^\mbhgf^^ml
ma^liZg[Z\dmhma^lniihkmlb_ln__b\b^gmk^bg_hk\^f^gmblikhob]^] ma^fbgbfnf\khll&l^\mbhgZepb]mak^jnbk^f^gmlbgMZ[e^0'
ho^kma^lniihkmZg]maZmmablk^bg_hk\^f^gmbllnbmZ[er\nkmZbe^]mh
Z\\hffh]Zm^ma^[^g]bg`fhf^gm^goêhi^' B_ma^fbgbfnfk^jnbk^f^gmlZk^f^m%ma^Zk^Zghm]ZfZ`^][r
a^Zm%b'^'pbmabgma^.))<blhma^kf%bl]^m^kfbg^]mh`bo^Zk^]n\^]
l^\mbhglbs^![_b%]_b"pa^k^ma^\hg\k^m^k^mZbglbmlhkb`bgZeikhi^kmb^l'
Ma^fb]&liZgfhf^gmk^lblmZg\^\Zg[^\Ze\neZm^]_khfma^
^qik^llbhg_hkFK]%_bZ[ho^'Ma^Â_k^^Ã[^g]bg`fhf^gm_hkma^_bk^ Pabelmma^m^fi^kZmnk^`kZ]b^gmmakhnàZl^\mbhg]^ghm^][r
lbmnZmbhgblma^g]^m^kfbg^]Zg]Â_bmm^]Ãmhma^fhf^gmh_k^lblmZg\^ blhma^kflfZr[^]^m^kfbg^]_khfm^lmbg`%IZkm*¾+ikhob]^l
h_ma^liZg'Ma^fhf^gmh_k^lblmZg\^Zmma^lniihkm_hkma^_bk^\Zl^ m^fi^kZmnkîkh_be^l_hkZgnf[^kh_mrib\Zef^f[^kmri^lZg]
fZrma^g[^\Ze\neZm^]Zl_heehpl3 \khll&l^\mbhgl'!L^^^qZfie^bg?b`nk^*-"'

FK]%_b%Lniihkm6!gl (gl%_b"F>]!:l%ikho(:l%k^j"!]Z"(]
Ma^khng]^]\hkg^klh_ma^k^lb]nZel^\mbhgk^_e^\mma^k^Zeikh_be^h_
pa^k^ ma^blhma^kfZg]fZr[^ZiikhqbfZm^]mhZk^\mZg`e^Zllahpgbg
] 6 ^__^\mbo^]^imah_ma^l^\mbhg ?b`nk^*,4lhf^bgm^kik^mZmbhgfZr[^k^jnbk^]'
Z 6 k^jnbk^]Zo^kZ`^[hmmhfZqbl]blmZg\^mZd^g_khfMZ[e^-%
\henfg-%_hk[^Zfl%Zg]_khfMZ[e^._hkhg^&pZrleZ[l JWXb[-
Minimum width of cross-section as function of fire resistance
:l%ikho(:l%k^jlahne]ghm[^mZd^g`k^Zm^kmaZg*','
Fire resistance K/) K2) K*+) K*1) K+-)
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

Minimum width of 2) +) /) +)) +1)

<_]kh['' cross-section (mm)
Flow chart for simplified calculation method for beams and slabs

<_]kh['(
Start
H[\[h[dY[Ykhl[i\ehYh_j_YWbj[cf[hWjkh[e\h[_d\ehY_d]WdZfh[ijh[ii_d]
ij[[b\ehki[m_j^jWXkbWhc[j^eZWdZ7dd[n;
Calculate MEd, fi.

Determine y, using temperature profiles in Annex A of Part 1-2. 1.0

Determine ks(y) from Figure 12

0.8
Calculate MRd, fi
Coefficient, ks (ycr) or kp (ycr)

Reinforcing steel
Yes 0.6
Is the element a Is MEd, fi. ) MRd, fi? Yes
simply supported?
Prestressing steel (bars)
No No 0.4
Calculate the support design Redesign section or use
moment of resistance, alternative methods
MRd, fi, support Prestressing steel
Yes 0.2 (wires and strands)
‘Fit’ the ‘free’ bending Are the support
moment so that MEd,fi = MRd,fi moments exceeded?
0
0 200 400 600 800 1000 12
No
o
Finish Temperature, y ( C)

109
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
How to design concrete structures using Eurocode 2

Hg\^ma^k^]n\^]\khll&l^\mbhgbl]^m^kfbg^]%ma^m^fi^kZmnk^h_ :l+ 6 iZkmh_m^glbhgk^bg_hk\^f^gmbg^jnbeb[kbnf

^Z\ak^bg_hk\bg`[Zkbl_hng]nlbg`m^fi^kZmnkîkh_be^lZg]_khf pbmama^\hfik^llbhgk^bg_hk\^f^gm
mabl%ma^k^]n\^]lmk^g`mah_ma^k^bg_hk\^f^gm]n^mhm^fi^kZmnk^ :lÃ 6 Zk^Zh_\hfik^llbhgk^bg_hk\^f^gm
fZr[^]^m^kfbg^]bgZ\\hk]Zg\^pbma?b`nk^l,Zg]-'Ghm^maZm% _\]%_b!+)" 6 ]^lb`goZen^h_\hfik^llbhglmk^g`ma\hg\k^m^bg
bglhf^bglmZg\^l%ma^k^bg_hk\^f^gmfZr_Zeehnmlb]^h_ma^k^lb]nZe ma^_bk^lbmnZmbhgZmghkfZem^fi^kZmnk^
\khll&l^\mbhg'Bgln\a\Zl^l%ma^l^[ZklfZrlmbee[^\hngm^]pa^g 6 _\d (g\%_b6_\]
]^m^kfbgbg`ma^l^\mbhg\ZiZ\bmr' _l]%_b!yf" 6 ]^lb`goZen^h_ma^m^glbhgk^bg_hk\^f^gmlmk^g`mabg
ma^_bk^lbmnZmbhgZmf^Zgm^fi^kZmnk^yfbgmaZmeZr^k
Ma^l^\mbhgk^lblmZg\^fZrma^g[^]^m^kfbg^]nlbg`\hgo^gmbhgZe _l\]%_b!yf"6 ]^lb`goZen^h_ma^\hfik^llbhgk^bg_hk\^f^gmlmk^g`ma
\Ze\neZmbhgf^mah]l%Zlbg]b\Zm^]bg?b`nk^*.Zg]\hfiZk^]Z`Zbglm bgma^_bk^lbmnZmbhgZmf^Zgm^fi^kZmnk^yfbgmaZmeZr^k
ma^]^lb`gehZ]bgma^_bk^lbmnZmbhgbgmabl_b`nk^pa^k^3
Note: _l]%_b!yf"Zg]_l\]%_b!yf"fZraZo^]b__^k^gmoZen^l!l^ÎZkm*+%
[_b 6 pb]mah_k^]n\^]\khll&l^\mbhg <e-'+'-',"
]_b 6 ^__^\mbo^]îmah_ma^k^]n\^]\khll&l^\mbhg ?l 6 mhmZe_hk\^bg\hfik^llbhgk^bg_hk\^f^gmbgma^
s 6 eô^kZkf[^mp^^gma^m^glbhgk^bg_hk\^f^gm _bk^lbmnZmbhg%Zg]bl^jnZemhiZkmh_ma^mhmZe_hk\^bg
Zg]\hg\k^m^ ma^m^glbhgk^bg_hk\^f^gm
sÃ 6 eô^kZkf[^mp^^gma^m^glbhgZg]\hfik^llbhg l%nZg]qZk^]^_bg^]bg>nkh\h]^+%IZkm**
k^bg_hk\^f^gm
:l 6 Zk^Zh_m^glbhgk^bg_hk\^f^gm Pa^gma^k^bg_hk\^f^gmbl]blmkb[nm^]bgfhk^maZghgêZr^k%IZkm*¾+
:l* 6 iZkmh_m^glbhgk^bg_hk\^f^gmbg^jnbeb[kbnf h__^kllbfieb_rbg`f^mah]lmh]^m^kfbg^ma^Zqbl]blmZg\^mhma^\^gmk^
pbmama^\hg\k^m^\hfik^llbhg[eh\d h_ma^k^bg_hk\^f^gmeZr^klZg]ma^m^fi^kZmnk^k^]n\mbhgZmmableôê'
<_]kh[')
Reduced cross-section of reinforced concrete beam and column Ma^[^g]bg`fhf^gm\Ze\neZmbhgh_ma^\khll&l^\mbhgbl3

Compression Tension Fn6 :l _l]%_b!yf"s

Fn+6 :l+ _l\]%_b!yf"sÃ
o
500 C 500oC :l 6 :l*$:l+
d fi = d
d fi pa^k^
:l 6 mhmZem^glbhgk^bg_hk\^f^gmZk^Z
_l]%_b 6 ]^lb`gm^glbe^lmk^g`mah_k^bg_hk\^f^gm
Tension Compression _l\]%_b 6 ]^lb`glmk^g`ma_hk\hfik^llbo^k^bg_hk\^f^gm
b fi [_b 6 pb]mah_ma^_bk^^qihl^]\khll&l^\mbhg
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

bfi
b b ]_b 6 ^__^\mbo^a^b`amh_ma^_bk^^qihl^]\khll&l^\mbhg
a) Fire exposure on three sides b) Fire exposure on three sides with
with tension zone exposed the compression zone exposed <_]kh['*
;nWcfb[j[cf[hWjkh[fhe\_b[\ehW,&&n)&&X[WcWdZH/&

500oC 240
Distance from bottom left corner of element (mm)

h fi h
220

200
b fi
b 180
100
c) Fire exposure on four sides (beam or column) 160

140
<_]kh['+
Ijh[iiZ_ijh_Xkj_edWjkbj_cWj[b_c_jijWj[\ehWh[YjWd]kbWhYedYh[j[ 200
120
cross-section with compression reinforcement.
100 300
n f cd, 1(20)
80 400
Fs = As1f scd,fi (ym)
l xb n fcd, 1(20) 500
x lx 60
600
A s1 700
z’ Mu2 40
z’ d\_ z Mu1 800
20 900
As As1 fsd,fi (ym)
0
b1 0 20 40 60 80 100 120 140
Distance from bottom left corner of element (mm)

110
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
12. Structural fire design

Pa^gma^fhf^gm\hgmkb[nmbhglZk^Zll^ll^]ZllahpgZ[ho^%ma^ @bo^gma^\hfie^qbmrh_ma^ZiikhZ\a%ma^mZ[e^lbg:gg^q<h_
mhmZefhf^gm\ZiZ\bmrblh[mZbg^]_khf3 IZkm*+aZo^[^^g]^kbo^]_khfmablf^mah]Zg]fZr[^nl^]mh
Fn6Fn*$Fn+ \a^\dmaZmma^l^\mbhglbs^Zg]Zqbl]blmZg\^lZk^Z]^jnZm^_hkZ
`bo^g\Zl^'
Ma^]^lb`gikh\^llbllnffZkbl^]bg?b`nk^*/'
Calculation methods for shear and torsion
9heii#i[Yj_edi[nfei[ZjeX[dZ_d]WdZWn_WbbeWZ Pa^gnlbg`ma^mZ[neZkf^mah]%b_ma^fbgbfnfl^\mbhg]bf^glbhgl
:gg^q;',ikhob]^lZ\Ze\neZmbhgf^mah]_hkf^f[^kl!ikbfZkber Zkîkhob]^]%gh\a^\dl[^rhg]mahl^\Zkkb^]hnm_hkZf[b^gm
\henfgl"pa^k^ma^lmkn\mnkZe[âZobhnkbllb`gb_b\Zgmerbg_en^g\^] m^fi^kZmnk^]^lb`gZk^k^jnbk^]'Bghma^k\Zl^l%f^f[^kk^lblmZg\^
[rl^\hg]hk]^k^__^\mlng]^k_bk^\hg]bmbhgl'Ahpô^k%Zlpbmama^ lahne][^]^m^kfbg^][r\Ze\neZmbhgZg]`nb]Zg\^bl`bo^gbg:gg^q=
mZ[neZkf^mah]%ma^ZiikhZ\ablebfbm^]mhf^f[^klmaZm\Zg[^ h_IZkm*+'
\hglb]^k^]Zl[^bg`[kZ\^]'
?hkmrib\Zel^\mbhgl%la^Zk_Zbenk^]n^mh_bkêhZ]bg`blng\hffhgZg]
<_]kh[', pabelmghm[^bg`_neeroZeb]Zm^]%pa^gnlbg`ma^\Ze\neZmbhgf^mah]
<bemY^Whj\eh+&&9_iej^[hcc[jêZ
ik^l^gm^]%maîkbg\bie^lbg>nkh\h]^+%IZkm**fZr[^Ziieb^]mhZ
k^]n\^]\khll&l^\mbhgZl]^m^kfbg^]_khfZgrh_ma^\Ze\neZmbhgf^mah]l
Start eblm^]Z[ho^'Ahpô^k%_hkZmrib\Zel^\mbhgl%ln\aZlmahl^pbmamabgp^[l
pa^k^p^[_Zbenk^fZr`ho^kg%ma^l^f^mah]llahne][^nl^]pbma\Zk^'
Calculate MEd, fi (see simplified calculation method for beams and slabs)

Check the minimum dimensions exceed the values in Table 7

Bg\Zl^lpa^k^la^Zkk^bg_hk\^f^gmblghmikhob]^]%ma^l^\mbhg
k^lblmZg\^mhla^Zkblikhob]^][rma^\hg\k^m^'Bgln\a\Zl^lmabl
Determine reduced section size (bfi dfi) using Figure 13 and k^lblmZg\^fnlm[^k^]n\^]mhZ\\hngm_hkm^fi^kZmnk^^__^\ml[rZ
temperature profiles in Annex A of Part 1–2
_Z\mhkh_d\m!y "%pab\afZr[^mZd^g_khf?b`nk^*0'Bg\Zl^lpa^k^
Determine y, using temperature profiles in Annex A of Part 1–2 ebgdlZk^ikhob]^]%pa^ma^k_hkla^ZkZehg^hkZelh_hkmhklbhg%ma^
lmk^g`mah_ma^ebgdlblk^]n\^]]n^mhma^m^fi^kZmnk^^__^\mlZg]ma^
Determine ks (y ), from Figure 3 or Figure 4
l^\mbhgk^lblmZg\^ma^g]^m^kfbg^]%[Zl^]hgma^k^]n\^]l^\mbhg'Ma^
Calculate Mu, using stress distribution shown in Figure 15. Mu = Mu1 + Mu2
\Ze\neZmbhgikh\^llbllahpgbg?b`nk^*1'

--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---
<_]kh['.
Is MEd,fi ) MRd,fi?
No Redesign section or use :[i_]d\bemY^Whj\ehi^[WhWdZjehi_edZ[i_]d
alternative methods

Yes Start
Finish
Determine the reduced cross-section using either 500°C
isotherm or zone methods

<_]kh['- Calculate the compressive and tensile concrete strengths:

For isotherm method, fcd,fi = fcd,fi(20) = fck and fctd,fi = fctd,fi(20) = fctk
Coefficient kc,t(yWbbem_d]\ehZ[Yh[Wi[e\j[di_b[ijh[d]j^fck,t) of
For zone method, fcd,fi = kc(ym) fcd,fi(20) and fctd,fi = kct(ym) fctd,fi(20),
concrete at elevated temperatures where kc(ym) and kct(ym) may be taken as kc(y) and can be determined
from Figure 2

Determine position P, the point at which the reference temperature,

y p is calculated. P is located along section A–A, which is
1.0 determined from hc,ef (see Figure 19)

Determine y p using temperature profiles in Annex A of Part 1–2

0.8
Coefficient, k c, t (y )

Calculate the reduced design strength of the shear reinforcement, fsd,fi,

from: fsd,fi = ks(y) fsd(20) = ks(y) fywd
0.6 where ks(y) can be determined from Figure 3 or Figure 4

Calculate the shear resistance using the methods given for ambient
0.4 temperature design, see Chapter 4

Yes Calculate the reference

0.2 Does the section
temperature at points P along
also resist torsion?
the line A–A − see Figure 20

0
0 100 200 300 400 500 600 No
Calculate the torsion resistance
o Finish and interaction with shear using
Temperature, y ( C)
section 6.3 of Eurocode 2, Part 1–1

111
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
12. Structural fire design

Unbraced structures
BmaZl[^^gghm^]maZm_hk\henfglZg]pZeel%pa^gnlbg`ma^mZ[neZk ?hkbgbmbZe]^lb`g%ma^[Z\d`khng]iZi^kmhma^NDGZmbhgZe:gg^q^l2
f^mah]%[kZ\^]lmkn\mnk^lhgerZk^\hglb]^k^]bgIZkm*+'MablblZelh mh;L>G*22+*lmZm^lmaZm%Zmma^]bl\k^mbhgh_ma^]^lb`g^k%ma^
mkn^_hkma^lbfieb_b^]\Ze\neZmbhgf^mah]ik^l^gm^]bg:gg^q;',% mZ[neZkf^mah]fZr[^nl^]_hk`^g^kZe]^lb`gZg]\kbmb\Ze\henfgl
pab\abl]^l\kb[^]ZlZshg^f^mah]_hkma^ZgZerlblh_\henfglpbma \a^\d^]bgZ\\hk]Zg\^pbma^bma^kma^.))<blhma^kff^mah]hkma^
lb`gb_b\Zgml^\hg]hk]^k^__^\ml' shg^f^mah]'

Bg\Zl^lpa^k^ma^lmkn\mnk^blng[kZ\^]%hkmaZmihkmbhgh_ma^ Ln\aZgZiikhZ\aphne][^nglZ_^pa^k^ma^f^f[^klbgma^_bk^
lmkn\mnk^[^bg`\hglb]^k^]\Zgghm[^\hglb]^k^]Zl[kZ\^][rmaZm shg^ikhob]^ma^ik^]hfbgZgmf^Zglh_lmkn\mnkZelmZ[bebmrZg]bg
iZkmh_ma^lmkn\mnk^k^fhm^_khfma^_bk^ma^gma^_heehpbg`himbhgbl ln\a\Zl^lZ]oZg\^]\Ze\neZmbhgf^mah]lZg]li^\bZeblmZ]ob\^fZr[^
ZoZbeZ[e^mhma^^g`bg^^k' k^jnbk^]'

<_]kh['/ <_]kh[(&
:[j[hc_dWj_ede\b_d[7¸7je[dWXb[[lWbkWj_ede\h[\[h[dY[ The reference temperature ypi^ekbZX[[lWbkWj[ZWbed]j^[b_d[7¸7\eh
temperature y p at point P the calculation of torsion resistance

x
e2 = 0
y p in links
d A A
h
A A
A
A
h c,ef A A
A

A c,eff e1
A
c,ef = MIN {2.5 ( ); (

References
' ;KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22+*+%=^lb`gh_\hg\k^m^lmkn\mnk^l'@^g^kZekne^llmkn\mnkZe_bk^]^lb`g';LB%+))-'
2 BGLMBMNMBHGH?LMKN<MNK:E>G@BG>>KL'@nb]^mhma^Z]oZg\^]_bk^lZ_^mr^g`bg^^kbg`h_lmkn\mnk^l'BLmkn\m>%+))0'
) ;KBMBLALM:G=:K=LBGLMBMNMBHG'G:mh;L>G*22+*+%NDGZmbhgZe:gg^qmh>nkh\h]^+3=^lb`gh_\hg\k^m^lmkn\mnk^l'@^g^kZekne^llmkn\mnkZe_bk^
]^lb`g';LB%+)).'
* ;
:BE>R%<'DAHNKR%@'@nb]^mhma^i^k_hkfZg\^h_\hg\k^m^lmkn\mnk^lbg_bk^'Ma^<hg\k^m^<^gmk^%]n^+))2'
+ ;
KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22**+%>nkh\h]^*3:\mbhglhglmkn\mnk^l'@^g^kZeZ\mbhgl:\mbhglhglmkn\mnk^l^qihl^]mh_bk^'
;LB%+))+'
6 ;KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22)%>nkh\h]^3;Zlblh_lmkn\mnkZe]^lb`g';LB%+))+'
-;KBMBLALM:G=:K=LBGLMBMNMBHG';L>G*22+**%>nkh\h]^+3=^lb`gh_\hg\k^m^lmkn\mnk^l'@^g^kZekne^lZg]kne^l_hk[nbe]bg`l';LB%+))-'
--`,``,,```,,`,`,`,``,`,,```,`-`-`,,`,,`,`,,`---

.BGLMBMNMBHGH?LMKN<MNK:E>G@BG>>KL'FZgnZe_hkma^]^lb`gh_\hg\k^m^[nbe]bg`lmkn\mnk^lmh>nkh\h]^+'BLmkn\m>%+))/'
/;KBMBLALM:G=:K=LBGLMBMNMBHG'I=//10&*%;Z\d`khng]iZi^kmhma^NDGZmbhgZe:gg^qmh;L>G*22+**';LB%+)*)

112
Copyright The Concrete Centre
Provided by S&P Global Licensee=AMEY RAIL LIMITED/8246394001, User=Eatherington, Douglas
No reproduction or networking permitted without license from S&P Global Not for Resale, 01/08/2023 07:29:05 MST
Authors of the ﬁrst edition
Dr Andrew Bond, UK delegate on the CEN/TC 250/SC7 committee responsible for Eurocode 7.
Owen Brooker, Senior Structural Engineer, MPA The Concrete Centre.
Dr Andrew Fraser, Senior Engineer, Arup Advanced Technology and Research.
Andrew Harris, former Associate Dean of Kingston University, expert in Eurocode 7.
Prof Tom Harrison, chairman of the BSI concrete committee.
Dr Tony Jones, Associate Director, Arup Advanced Technology and Research at Arup. On BSI Committee responsible for the
maintenance of existing British Standards and the CEN committee responsible for the development of European Codes.
Dr Richard Moss, formerly of Building Research Establishment.
Prof R S Narayanan, past Chairman of CEN/TC 250/SC2.
Rod Webster, Concrete Innovation and Design.

Members of the Steering Group for ﬁrst edition

John Mason, Alan Baxter & Associates (Chairman)
Stuart Alexander, WSP Group plc
Pal Chana, MPA Cement
Charles Goodchild, MPA The Concrete Centre
Tony Jones, Arup
Andy Lyle, NRM Consultants
Richard Moss, formerly of Powell Tolner Associates
Nary Narayanan, Clark Smith Partnership
Richard Shipman, DCLG
Robert Vollum, Imperial College, University of London
Russ Wolstenholme, WS Atkins & DTI Project Ofﬁcer
Rod Webster, Concrete Innovation and Design

Members of the Concrete Industry Eurocode 2 Group (CIEG) for ﬁrst edition
John Moore, Consultant (Chairman)
Clive Budge, British Precast
Pal Chana, MPA Cement
John Clarke, The Concrete Society
Colin Cleverly, Construct
Charles Goodchild, MPA The Concrete Centre
Haig Gulvanessian, Building Research Establishment
Geoff Harding, DCLG
Tom Harrison, MPA BRMCA
Tony Jones, Arup
John Mason, Alan Baxter & Associates
Richard Moss, formerly of Powell Tolner Associates
Nary Narayanan, Clark Smith Partnership
Richard Shipman, DCLG
Martin Southcott, Consultant
Russ Wolstenholme, W S Atkins
Rod Webster, Concrete Innovation and Design

All information correct at the time of publishing the ﬁrst edition.

--`,``,,```,,`,`,`,``,`,,

Copyright The Concrete Centre

UDC
624.012.4.001.63

How to Design Concrete Structures using Eurocode 2

Second edition

This publication brings together in one place “How to...”

guidance for the design, speciﬁcation and detailing of a broad
range of concrete elements.

This publication take the practising engineer through the process of

designing to Eurocode 2 and includes commentary, ﬂow charts, data
tables and design aids to enable designers to apply Eurocode 2 quickly
and conﬁdently to the design of concrete structures.

CCIP–060
Second edition
Published February 2018
ISBN 978-1-908257-21-5