SITRANS F flowmeters

SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40

■ Overview ■ Application
Coriolis mass flowmeters are suitable for measuring all liquids
and gases. The measurement is independent of changes in pro-
cess conditions/parameters such as temperature, density, pres-
sure, viscosity, conductivity and flow profile.
Due to this versatility the meter is easy to install and the coriolis
flowmeter is recognized for its high accuracy in a wide turn down
range which is a paramount in many applications.

The main applications of the coriolis flowmeter can be found in all

industries, such as:
Chemical & pharma Detergents, bulk chemicals, phar-
maceuticals, acids, alkalis
MASS 2100 DI 3 to DI 40 is suitable for accurate mass flow mea-
surement for all kind of liquids and gases.
Food & beverage Dairy products, beer, wine, soft-
drinks, plato/brix, fruit juices and
pulps, bottling, CO2 dosing, CIP-
4
The sensor offers superior performance in terms of flow accu- liquids
racy, turn-down range and density accuracy. The ease of instal-
Automotive Fuel injection nozzle & pump test-
lation through a plug & play mechanical and electrical interface ing, filling of AC units, engine con-
ensures optimum performance and operation. sumption, paint robots
The sensor delivers true multi parameter measurements i.e.: Oil & gas Filling of gas bottles, furnace con-
Mass flow, volume flow, density, temperature and fraction. trol, CNG-dispensers, test separa-
tors, LPG
■ Benefits Water & waste water Dosing of chemicals for water
treatment
• High accuracy better than 0.1% of mass flow rate
• Large dynamic turn down range better than 500:1 The wide varity of combinations and versions from the modular
system means that ideal adaptation is possible to each measur-
• Densitometer performance available through a density accu- ing task.
racy better than 0.0005 g/cm3 with a repeatability better than
0.0001 g/cm3
• Single tube without internal welds, reductions or flow splitters
■ Design
offers optimal hygiene, safety and CIP clean-ability for food & The MASS 2100 sensor consists of a single bent tube in a double
beverage and pharmaceutical applications bent pipe configuration, welded directly to the process connec-
• Markets biggest wall thickness, ensuring optimal lifetime and tors at each end.
corrosion resistance and high pressure durability The centre-block is brazed onto the sensor pipes from the out-
side acting as a mechanical low pass filter.
• Full bore design provides lower pressure loss due to same in-
ternal diameter throughout the entire sensor. The sensor is available in 2 material configurations, AISI 316L or
• Balanced pipe design with little mechanical energy-loss, en- Hastelloy C 22 with a wide variety of process connections.
sures optimal performance and stability under non ideal and The enclosure is made in stainless steel AISI 316L 1.4404 with a
unstable process conditions (pressure, temperature, density- grade of encapsulation of IP66/NEMA 4.
changes etc.)
The sensor is as standard EEx ia approved, intrinsically safe
• 4-wire Pt1000 temperature measurement ensures optimum
accuracy on mass flow, density and fraction flow The sensor can be installed in horizontal or vertical position. In
• Multi-plug electrical connector & SENSORPROM enables true horizontal position the sensor is self draining.
plug&play. Installation and commissioning in less than 10 min. Heating Jacket: All the sensors MASS 2100, Di 3 to Di 40, can
• Intrinsically safe Ex-design ia IIC as standard, making service optionally be equipped with a heating coil to avoid solidification
in hazardous area possible without having to demount the of sensitive fluids during down time or period between discon-
sensor if a compact Ex d transmitter needs service tinuing processes. This feature gives the user an alternative to
• Sensor pipe available in high quality AISI 316L stainless steel the costly electrical heating normally used, as gives the freedom
1.4435 or Hastelloy C 22 2.4602 offering optimum corrosion to choose either hot water, superheated steam or hot oil, to main-
resistance tain a constant temperature inside the sensor.
• Centre-block design decouples process noise from the envi-
ronment such as vibrations, pulsations, pressure shocks etc.
making installation flexible and versatile
• Rugged and space saving sensor design in stainless steel
matching all environments
• High pressure program as standard
• The sensor calibration factor is also valid for gas measure-
ment
• Uniform sensor interface matching all transmitter versions at
the same time whether it is compact IP67/NEMA 4X, compact
Ex-d or remote installation, one sensor fits all

Siemens FI 01 · 2006 4/135

 SITRANS F flowmeters
SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40

■ Function
The measuring principle is based on coriolis law of movement,
see “System information MASSFLO coriolis mass flowmeters”.

■ Integration
The sensor can be connected to all MASS 6000 transmitters for
compact as well as remote installation.
All sensors are delivered with a SENSORPROM containing all in-
formation about calibration data, identity and factory pre-pro-
gramming of transmitter settings. Cross talk

Installation guidelines MASS 2100 DI 3 ... DI 40 (1/8” ... 1½”) Cross talk between sensors mounted close to each other may
disturb the measurement. To avoid cross talk never mount more

4
Installation of sensor than one meter on each frame and mount flexible hose connec-
tions between the sensors as shown.

Horizontal (self-draining)
Zero-point adjustment
With low flow, horizontal mounting is recommended, as in this
position air bubbles are easier to remove. To facilitiate zero-point adjustment a shut-off valve should always
be mounted in connection with the sensor as a proper zeropoint
setting is essential for a good accuarcy.

Vertical
If the liquid is volatile or contains solid particles, vertical mount-
ing is not recommended.

Vibration
Always locate the flowmeter as far away as possible from com-
ponents that generate mechanical vibration in the piping.

4/136 Siemens FI 01 · 2006

 SITRANS F flowmeters
SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40

■ Technical specifications
Versions mm (inch) DI 3 (1/8) DI 6 (½) DI 15 (5/8) DI 25 (1) DI 40 (1½)
Inside pipe diameter (sen- mm (inch) 3.0 (0.12) 6.0 (0.24) 14.0 (0.55) 29.7 (1.17) 43.1 (1.70)
sor consists of one continu-
ous pipe)
Pipe wall thickness mm (inch) 0.5 (0.02) 1.0 (0.04) 1.0 (0.04) 2.0 (0.08) 2.6 (0.10)
Mass flow measuring kg/h (lb/h) 0 ... 250 (0 ... 550) 0 ... 1,000 0 ... 5,600 0 ... 25,000 0 ... 52,000
range (0 ... 2,200) (0 ... 12,345) (0 ... 55,100) (0 ... 114,600)
Density g/cm3 0 ... 2.9 (0 ... 181)
(lb/inch3)
Fraction e.g. °Brix 0 ... 100
Temperature
Standard
Liquid pressure measur-
°C (°F) -50 ... +180 °C (-58 ... +356 °F)
4
ing pipe 1)
Stainless steel bar (psi) 230 (3336) 265 (3844) 130 (1885) 110 (1595) 105 (1523)
Hastelloy C-22 bar (psi) 350 (5076) 410 (5946) 200 (2900) 185 (2683) not available
Materials
Measuring pipe, flange and 1.4435 (AISI 316 L) (Stainless steel)
thread connection
2.4602 (Hastelloy C-22) not available
Enclosure and enclosure IP66 and 1.4404 (AISI 316 L) (Stainless steel)
material
Enclosure IP65 (NEMA 4) and 1.4404 (AISI 316L) (Stainless steel), housing is not rated for pressure containment
Process connections 2)
Flange
• EN 1092-1, PN 40 DN 10 DN 15 DN 25 DN 40
• ANSI B16.5, Class 150 ½” ½” 1” 1½”
• ANSI B16.5, Class 600 ½” ½” 1” 1½”
(Class 300)
Dairy screwed connector
(PN 16/25/40) 3)
• DIN 11851 DN 10 DN 15 DN 32 DN 40
• ISO 2853/BS 4825 part 4 25 mm 25 mm 38 mm 51 mm
(SS3351)
Clamp (PN 16) 3)
• ISO 2852/BS 4825 part 3 25 mm 25 mm 38 mm 51 mm
(SMS3016)
Thread
• ISO 228/1, PN 100 G¼” G¼” G½” G1“ G2“
• ANSI/ASME B1.20.1, ¼” NPT ¼” NPT ½” NPT 1“ NPT 2“ NPT
PN 100
Cable connection Multiple plug connection to sensor 5 x 2 x 0.35 mm2 twisted and screened in pairs, ext. Ø 12 mm
Ex-version EEx ia IIC T3-T6, DEMKO 03 ATEX 135252X
Weight approx. kg (lb) 4 (8.8) 8 (17.6) 12 (26.5) 48 (105.8) 70 (154.5)
1) Max. at 20 °C (68 °F), DIN 2413, DIN 17457
2) Other connections to order, see “Selection and Ordering data”
3) Material, 1.4401 or corresponding
For accuracy specification see “System information MASSFLO”.

Siemens FI 01 · 2006 4/137

 SITRANS F flowmeters
SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40
Pressure drop

∆p [bar] Viscosity (cSt) ∆p [ bar] Viscosity [cSt]

0 00 0
100 500 200 100 50 20 10 50
10
10
0
20

10

0
10
5

50
2

20
1

1
1.0
1.0

0.1
0.1
60 100 1000 6000
3 10 100 300
Mass flow [kg/h]
Mass flow [kg/h]

MASS 2100 DI 3 (1/8”), pressure drop for density = 1000 kg/m3 MASS 2100 DI 15 (½”), pressure drop for density = 1000 kg/m3

∆p [bar] Viscosity [cSt] ∆p [ bar] Viscosity [cSt]

00 0 0 0

00
10 50 20 10

10
10 10

0
50
50
20

0 200
10
1

50
1.0 1.0

20
1

0.1 0.1
10 100 1000 300 1000 10000 30000
Mass flow [kg/h] Mass flow [kg/h]

MASS 2100 DI 6 (¼“), pressure drop for density = 1000 kg/m3 MASS 2100 DI 25 (1”), pressure drop for density = 1000 kg/m3

4/138 Siemens FI 01 · 2006

 SITRANS F flowmeters
SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40

∆p [ bar] Viscosity [cSt]

10

00
10
0
50
10 200
0
1.0

20 50
4
1

0.1
500 1000 10000 50000
Mass flow [kg/h]

MASS 2100 DI 40 (1½”), pressure drop for density = 1000 kg/m3

Siemens FI 01 · 2006 4/139

 SITRANS F flowmeters
SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40
Selection and Ordering data Order-No. Order code Selection and Ordering data Order-No. Order code
SITRANS F C sensors SITRANS F C sensors
MASS 2100 without heating jacket 7 ME 4 1 0 0 - MASS 2100 without heating jacket 7 ME 4 1 0 0 -
MASS 2100 heated, DN 15 connection 7 ME 4 2 0 0 - MASS 2100 heated, DN 15 connection 7 ME 4 2 0 0 -
MASS 2100 heated, ½ inch, ANSI B16.5 7 ME 4 2 1 0 - MASS 2100 heated, ½ inch, ANSI B16.5 7 ME 4 2 1 0 -
connection connection
7 77 7 7 - 7 7 7 7 7 7 7 7 77 7 7 - 7 7 7 7 7 7 7
Diameter Dairy screwed connection DIN 11851
Stainless steel 1.4435/316L DN 10 (PN 40) 40
DI 3 (PN 100/PN 230) 1C DN 15 (PN 40) 41
DI 6 1D DN 25 (PN 40) 42
DI 15 1E DN 32 (PN 40) 43
DI 25 1F DN 40 (PN 25) 44

4
DI 40 1G DN 50 (PN 25) 45
2.4602/Hastelloy C22 DN 65 (PN 25) 46
DI 3 (PN 100/PN 350) 2C Dairy clamp connection ISO 2852
DI 6 2D
25 mm (PN 16) 50
DI 15 2E 38 mm (PN 16) 51
DI 25 2F 51 mm (PN 16) 52
Pressure Dairy screwed connection ISO 2853
PN 16 (DI 6, DI 15, DI 25 and DI 40) A 25 mm (PN 16) 60
PN 25 (DI 6, DI 15, DI 25 and DI 40) B 38 mm (PN 16) 61
PN 40 (DI 6, DI 15, DI 25 and DI 40) C 51 mm (PN 16) 62
PN 100 (DI 3, DI 6, DI 15, DI 25 and DI 40) D Configuration
PN 105 (DI 40, 2“, 316L) E
PN 110 (DI 25, 1“, 316L) F Standard 1
Density 2
PN 130 (DI 15, ½“, 316L) G Brix/Plato 3
PN 185 (DI 25, 1“, Hastelly C-22) J
Fraction (specification required) 9 N0Y
PN 200 (DI 15, ½“, Hastelly C-22) K
PN 230 (DI 3, ¼“, 316L) L Transmitter compact mounted
PN 265 (DI 6, ¼“, 316L) M No transmitter A
PN 350 (DI 3, ¼“, Hastelloy C-22) N MASS 6000, Ex-d, stainless steel enclosure, B
PN 410 (DI 6, ¼“, Hastelloy C-22) Q 1 current, 1 freq./pulse and
1 relay output, 24 V AC/DC with EEx-de [ia/ib]
Class 150 (DI 6, DI 15, DI 25 and DI 40) R T3 -T6 Ex-approval.
Class 600 (DI 6, DI 15, DI 25 and DI 40) S
MASS 6000, IP67, Polyamide enclosure, C
Process connection/flange 1 current, 1 freq./pulse and 1 relay output,
24 V AC/DC.
Pipe thread
MASS 6000, IP67, Polyamide enclosure, D
G ¼“ 10 1 current, 1 freq./pulse and 1 relay output,
¼“ NPT 11 115/230 V AC 50/60 Hz
G ½“ 12
Cable
½“ NPT 13 No cable A
G1 14 5 m (16 ft) cable B
1“ NPT 15 10 m (32 ft) cable C
G 2“ 16 25 m (82 ft) cable D
2“ NPT 17 50 m (164 ft) cable E
Flange EN1092-1 75 m (246 ft) cable F
DN 10 (PN 40/PN 100) 20 150 m (492 ft) cable G
DN 15 (PN 40/PN 100) 21 Calibration
DN 25 (PN 40/PN 100) 22
Standard Calibration 1
DN 40 (PN 40/PN 100) 23 Standard Calibration matched pair 2
DN 50 (PN 40/PN 100) 24 Accredited Calibration (DANAK) 3
Flange ASME/ANSI B 16.5 Extended calibration customer specified 8
½“ (class 150/class 600) 30 select Y60, Y61, Y62 or Y63 (see Additional
information)
3/4“ (class 150/class 600) 31
1“ (class 150/class 600) 32 Please also see www.siemens.com/SITRANSFordering
1 ½“ (class 150/class 600) 33 for practical examples of ordering
2 “ (class 150/class 600) 34

4/140 Siemens FI 01 · 2006

 SITRANS F flowmeters
SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40
Accessories
Dairy MLFB example
MASS 2100 7 ME 4 1 0 0 - 77C77 1 7A7 Description Dimension Order No.

Stainless stell, DI 15 1E Mating parts for hygienic fittings DN 10 FDK:085U1016

DIN 11851
Dairy screwed connection 41 DN 15 FDK:085U1017
Includes:
DIN 11851, DN 15 DN 25 FDK:085U1019
• 2 unions
MASS 6000 IP67 compact mounted D • 2 mating parts (for welding in) DN 32 FDK:085U1020
• 2 EPDM gaskets
DN 40 FDK:085U1021
DN 50 FDK:085U1022
DN 65 FDK:085U1023
Mating parts for hygienic clamp 25 mm FDK:085U1029
ISO 2852
40 mm FDK:085U1031
Includes:
• 2 clamps
• 2 mating parts
50 mm FDK:085U1032
4
• 2 EPDM gaskets
Standard calibration 1
Gaskets for MASS 2100
Additional information Order code Description Dimension Order No.
Please add “-Z“ to Order No. and specify Order 2 EPDM gaskets with collar for DN 10 FDK:085U1006
code(s) and plain text.
mounting set DIN 11851 DN 15 FDK:085U1007
Pressure testing certificate C11
DN 25 FDK:085U1009
Material certificate C12
DN 32 FDK:085U1010
Welding certificate C13
DN 40 FDK:085U1011
Factory certificate according to EN 10204 2.2 C14
DN 50 FDK:085U1012
Factory certificate according to EN 10204 2.1 C15
DN 65 FDK:085U1013
Tag name plate, stainless steel Y17
Tag name plate, plastic Y18
Spare parts
Customer specific transmitter setup Y20
Description Length Order No.
Customer specified, matched pair (5x2) Y60
Multiple plug for cable mounting FDK:083H5056
Customer specified calibration (5x2) Y61
Cable with multiple plug 5 m (16.4 ft) FDK:083H3015
Customer specified, matched pair (10x1) Y62
Standard blue cable between 10 m (32.8 ft) FDK:083H3016
Customer specified calibration (10x1) Y63 MASS 6000 and MASS 2100,
5 x 2 x 0,34 mm2 twisted and 25 m (82 ft) FDK:083H3017
Special version Y99 screened in pairs. 50 m (164 ft) FDK:083H3018
Temperature range -20°C ... +110°C
(-68°F ... +230°F) 75 m (246 ft) FDK:083H3054
150 m (492 ft) FDK:083H3055
Adapter for MASS 2100 FDK:083L5052
2 kB SENSORPROM unit FDK:083H4410
(Sensor Serial No. and Order No. must be specified
by ordering)

Siemens FI 01 · 2006 4/141

 SITRANS F flowmeters
SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40

■ Dimensional drawings
MASS 2100 sensor





/


/


/
 %



'
+
'

'
'
'
/

'DLU\VFUHZHG
FRQQHFWLRQ
',1VFUHZHG /
&ODPS
,62
/

/ 6FUHZHGFRQQHFWRUIRU
'L,62*~
DQG$16,$60(
%~137


Sen- Connections L1 L2 L3 H1 B1 D1 D2 D3 D4 D5
sor mm mm mm mm mm mm mm mm mm mm
size
Type Pressure rating Size
DI 3 Pipe thread ISO 228/1 - G¼ PN 100 ¼” 400 280 75.0 60 0 21.3 104 - - -
(1/8“) Pipe thread ANSI/ASME B 1.20.1 - PN 100 ¼” 400 280 75.0 60 0 21.3 104 - - -
¼” NPT
DI 6 Flange EN 1092-1 PN 40 DN 10 560 390 62.0 40 12 17.0 104 90.0 60.0 14.0
(¼“) Flange ANSI B16.5 Class 150 ½“ 624 390 62.0 40 12 17.0 104 88.9 60.5 15.7
Flange ANSI B16.5 Class 600 ½“ 608 390 62.0 40 12 17.0 104 95.3 66.5 15.7
Screwed connection DIN 11851 PN 40 DN 10 532 390 62.0 40 12 17.0 104 - - -
Clamp ISO 2852 PN 16 25 mm 570 390 62.0 40 12 17.0 104 - - -
DI 15 Flange EN 1092-1 PN 40 DN 15 620 444 75.0 44 20 21.3 129 95.0 65.0 14.0
(½“) Flange ANSI B16.5 Class 150 ½“ 639 444 75.0 44 20 21.3 129 88.9 60.5 15.7
Flange ANSI B16.5 Class 600 ½“ 660 444 75.0 44 20 21.3 129 95.3 66.5 15.7
Screwed connection DIN 11851 PN 40 DN 15 586 444 75.0 44 20 21.3 129 - - -
Clamp ISO 2852 PN 16 25 mm 624 444 75.0 44 20 21.3 129 - - -
DI 25 Flange EN 1092-1 PN 40 DN 25 934 700 74.5 126 25 33.7 219 115.0 85.0 14.0
(1“) Flange ANSI B16.5 Class 150 1“ 967 700 74.5 126 25 33.7 219 108.0 79.2 15.7
Flange ANSI B16.5 Class 600 1“ 992 700 74.5 126 25 33.7 219 124.0 88.9 19.1
Screwed connection DIN 11851 PN 40 DN 32 922 700 74.5 126 25 33.7 219 - - -
Clamp ISO 2852 PN 16 38 mm 940 700 74.5 126 25 33.7 219 - - -
DI 40 Flange EN 1092-1 PN 40 DN 40 1064 850 71.5 180 0 48.3 273 150.0 110.0 18.0
(1½“) Flange ANSI B16.5 Class 150 1½“ 1100 850 71.5 180 0 48.3 273 127.0 98.6 15.7
Flange ANSI B16.5 Class 600 1½“ 1128 850 71.5 180 0 48.3 273 155.4 114.3 22.4
Screwed connection DIN 11851 PN 25 DN 50 1090 850 71.5 180 0 48.3 273 - - -
Clamp ISO 2852 PN 16 51 mm 1062 850 71.5 180 0 48.3 273 - - -

4/142 Siemens FI 01 · 2006

 SITRANS F flowmeters
SITRANS F C
MASSFLO MASS 2100 DI 3 to D 40
MASS 2100 sensor with “heating jacket”

+

/
'
' +

%
'

Sensor size Connec- L5 L3 H3 B2 D6 D7 D8

tions heated

4
Type Pressure rating Size mm mm mm mm mm mm mm
DI 3 (1/8“) EN 1092-1 PN 40 DN 15 234 75.0 122.0 22.0 95.0 65.0 14.0
ANSI B16.5 Class 150 ½" 234 75.0 131.6 22.0 88.9 60.5 15.7
DI 6 (¼“) EN 1092-1 PN 40 DN 15 234 62.0 112.0 22.7 95.0 65.0 14.0
ANSI B16.5 Class 150 ½" 234 62.0 121.6 22.7 88.9 60.5 15.7
DI 15 (½“) EN 1092-1 PN 40 DN 15 234 75.0 126.5 31.5 95.0 65.0 14.0
ANSI B16.5 Class150 ½" 234 75.0 136.1 31.5 88.9 60.5 15.7
DI 25 (1“) EN 1092-1 PN 40 DN 15 420 74.5 213.6 60 95.0 65.0 14.0
ANSI B16.5 Class 150 ½" 420 74.5 223.2 60 88.9 60.5 15.7
DI 40 (1½“) EN 1092-1 PN 40 DN 15 500 71.5 267.5 43 95.0 65.0 14.0
ANSI B16.5 Class 150 ½" 500 71.5 277.1 43 88.9 60.5 15.7

MASS 2100 and MASS 6000 Ex-d compact version MASS 2100 and MASS 6000 IP67 compact version

š 




Sensor size L3 H5 H6 H5 + H6
[DN (inch)] [mm (inch)] [mm (inch)] [mm (inch)] [mm (inch)]
3 (1/8) 75 (2.95) 82 (3.23) 307 (12.1) 389 (15.32) Sensor size L3 H5 H6 H5 + H6
[DN (inch)] [mm (inch)] [mm (inch)] [mm (inch)] [mm (inch)]
6 (¼) 62 (2.44) 72 (2.83) 317 (12.48) 389 (15.32)
3 (1/8) 75 (2.95) 82 (3.23) 246 (9.69) 328 (12.91)
15 (½) 75 (2.95) 87 (3.43) 328 (12.91) 414 (16.30)
6 (¼) 62 (2.44) 72 (2.83) 256 (10.08) 328 (12.91)
25 (1) 75 (2.95) 173 (6.81) 332 (13.07) 504 (19.84)
15 (½) 75 (2.95) 87 (3.43) 267 (10.51) 353 (13.90)
40 (1½) 75 (2.95) 227 (8.94) 332 (13.07) 558 (21.97)
25 (1) 75 (2.95) 173 (6.81) 271 (10.67) 443 (17.44)
40 (1½) 75 (2.95) 227 (8.94) 271 (10.67) 497 (19.57)

Siemens FI 01 · 2006 4/143