John Deere Xuv 825i s4 Gator Utility Vehicle Operators Manual

*DCY*
XUV 825i S4 Gator™ Utility

Vehicle
*OMM175908*
OPERATOR'S MANUAL
Gator™ Utility Vehicle XUV 825i S4

OMM175908 ISSUE I5 (ENGLISH)
CALIFORNIA
Proposition 65 Warning
Diesel engine exhaust and some of its constituents

are known to the State of California to cause cancer,
birth defects, and other reproductive harm.
If this product contains a gasoline engine:
WARNING
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
*OMM175908*
The State of California requires the above two warnings.

Additional Proposition 65 Warnings can be found in this manual.
John Deere Horicon Works

North American Edition
Printed in U.S.A.
Downloaded from manualsnet.com search engine

Introduction
Thank You for Purchasing a John Deere CAUTION: Avoid injury! This symbol and text
Product highlight potential hazards or death to the
We appreciate having you as a customer and wish you operator or bystanders that may occur if the
many years of safe and satisfied use of your machine. hazards or procedures are ignored.
IMPORTANT: Avoid damage! This text is used to tell

the operator of actions or conditions that might
Using Your Operator’s Manual result in damage to the machine.
This manual is an important part of your machine and
should remain with the machine when you sell it.
NOTE: General information is given throughout the
Reading your operator’s manual will help you and others manual that may help the operator in the operation
avoid personal injury or damage to the machine. or service of the machine.
Information given in this manual will provide the operator
with the safest and most effective use of the machine.
Knowing how to operate this machine safely and
correctly will allow you to train others who may operate Attachments for Your Machine
this machine. There’s a John Deere attachment or kit to make your new
If you have an attachment, use the safety and operating machine perform more tasks or be more versatile,
information in the attachment operator’s manual along whether your machine is a lawn tractor or compact utility
with the machine operator’s manual to operate the tractor or a utility vehicle.
attachment safely and correctly. You can check out the entire line of attachments for your
This manual and safety signs on your machine may also machine at JohnDeere.com or ask your John Deere
be available in other languages (see your authorized dealer. From aerators to electric lift kits to tillers, there’s a
dealer to order). John Deere attachment or kit to fill every need.
Sections in your operator’s manual are placed in a

specific order to help you understand all the safety
messages and learn the controls so you can operate this
machine safely. You can also use this manual to answer
any specific operating or servicing questions. A
convenient index located at the end of this book will help
you to find needed information quickly.
The machine shown in this manual may differ slightly
from your machine, but will be similar enough to help you
understand our instructions.
RIGHT-HAND and LEFT-HAND sides are determined by
facing in the direction the machine will travel when going
forward. When you see a broken line (------), the item
referred to is hidden from view.
Before delivering this machine, your dealer performed a
predelivery inspection to ensure best performance.
Special Messages
Your manual contains special messages to bring
attention to potential safety concerns, machine damage
as well as helpful operating and servicing information.
Please read all the information carefully to avoid injury
and machine damage.

Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety Labels Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Labels No-Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Machine Cleanout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Operating Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Optional Attachments & Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Service Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Service Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Service Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Service Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Service Steering & Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Service Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Service Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
John Deere Quality Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Service Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Original Instructions. All information, illustrations and specifications in this

manual are based on the latest information available at the time of publication.
The right is reserved to make changes at any time without notice.
COPYRIGHT © 2015
DEERE & COMPANY
Moline, Illinois
All rights reserved
A John Deere ILLUSTRUCTION © Manual
Previous Editions
Copyright © 2014, 2013, 2012

Product Identification
Record Identification Numbers
XUV 825i S4
PIN (110001-)
If you need to contact an Authorized Service Center for
information on servicing, always provide the product
model and identification numbers.
You will need to locate the identification numbers for the
product. Record the information in the spaces provided
below.
MXT008448—UN—29AUG13
DATE OF PURCHASE:
_________________________________________
DEALER NAME:
_________________________________________
DEALER PHONE:
_________________________________________
PRODUCT IDENTIFICATION NUMBER (A):
MXT008446—UN—27AUG13 _________________________________________
ENGINE SERIAL NUMBER (B):
_________________________________________
OPTIONAL ELECTRIC POWER ASSIST STEERING
(EPAS) SERIAL NUMBER (C):
_________________________________________
MXT010624—UN—23JUL14

Safety Labels Text
Safety Label Location
MXT015957—UN—18SEP15
A — OPS Label - M156705 H — WARNING - M167669

B — CAUTION - M160916 I — WARNING - M171805
C — CAUTION - M173254 J — CAUTION - M165302
D — WARNING - M171199 K — WARNING - M165302
E — WARNING - M173253 L — WARNING M177212 (Installed on optional toolbox)
F — WARNING - M171201 M — WARNING M177213 (Installed on optional toolbox)
G — CAUTION - M165798

Safety Labels Text
Understanding The Machine Safety Labels OPS/ROPS Protective Structure Safety and
Certification Label
MXAL42363—UN—22MAY13
The machine safety labels shown in this section are

placed in important areas on your machine to draw
attention to potential safety hazards.
On your machine safety labels, the words DANGER,
WARNING, and CAUTION are used with this safety-alert
symbol. DANGER identifies the most serious hazards.
The operator’s manual also explains any potential safety
hazards whenever necessary in special safety messages
that are identified with the word, CAUTION, and the
safety-alert symbol.
MXT012786—UN—22DEC14
Replace missing or damaged safety labels. Use this One label is installed on your machine depending upon your region.
operator’s manual for correct safety label placement.
OCCUPANT PROTECTIVE STRUCTURE
There can be more safety information contained on parts
and components sourced from suppliers that is not To maintain occupant protection and OPS certification:
reproduced in this operator’s manual. • Replace damaged OPS and worn seat belts. Do not
repair or revise.
French or Spanish Safety Labels and Operator’s
Manual • Any alteration of OPS must be approved by
manufacturer.
Operator’s manuals and safety labels with content in
French or Spanish are available for this machine through CERTIFICATION
authorized John Deere dealers. See your John Deere Performance certified to: SAE J2194
dealer.
John Deere Gator™ HPX
NOTE: Both text and no-text labels are shown. Your
machine is only equipped with one of these types John Deere Gator™ XUV
of labels.
Deere & Company Moline, Illinois, U.S.A.
CAUTION
MXAL44148—UN—10APR13
HELP PREVENT INJURY WHEN DUMPING LOADS

• Lock park brake before dumping

Safety Labels Text
• Operate dump on level ground only WARNING
• Keep hands away from cargo box
CAUTION
BEFORE LEAVING VEHICLE:

M171201—UN—20SEP13
• Stop engine Avoid Injury or Death from Rollover or Falling Off
• Set park brake
• Watch video and read operator’s manual before use.
• Remove key
• Passenger must be able to grasp handholds with
seatbelt on and both feet on floor.
• Vehicle is equipped with seatbelts and side doors or
WARNING nets. This safety equipment must be used by all
occupants.
• Wear helmets when driving aggressively, on rough or
uneven terrain, or at higher speeds.
• No more than one driver and one front passenger.
M171199—UN—27AUG13 • Keep arms and legs in during use.
Avoid Injury or Death from Rollover or Falling Off
• Watch video and read operator’s manual before use.
• Driver must be at least 16 years old with a valid driver CAUTION
license.
• Never operate vehicle under influence of alcohol or
drugs.
nets. This safety equipment must be used by all
occupants.
WARNING
• Avoid equipment fires.
Hot surface
• Accumulation of grass, leaves and other debris on or
near hot or moving parts can cause a fire.

Safety Labels Text
• Inspect machine before, during, and after use. Avoid Injury From Fire
• Shut off engine and allow machine to cool before
cleaning.
Inspect and clean the entire machine and pay special

attention to these locations:
1. Muffler and exhaust pipes
2. Exhaust manifold and heat shields
3. Skid plate (if equipped)
4. Radiator (if equipped)
• Static electricity may ignite fuel vapors.
• Place fuel container on ground when filling.
WARNING
Avoid Injury or Death from Falling Off
WARNING
• Only ride in seat with seat belt on.

• Do not ride in cargo box or on cargo racks.
Improper Loading Can Cause Rollover
M171805—UN—20SEP13

MXAL44146—UN—10APR13 • Keep arms and legs in during use.
• While turning, drive slow and do not accelerate.
• Secure and spread loads evenly.
• Drive slowly when loaded, on rough or uneven terrain,
• Do not exceed 1000 lb (454 kg) in cargo box. on paved surfaces, while operating at night or in
• Do not exceed gross vehicle weight of: reverse.
- 2-passenger vehicle 3100 lb (1406 kg) • Use brakes going down hills. Vehicle may freewheel.
- 4-passenger vehicle (S4) 3400 lb (1542 kg) • For off-road use only. Do not use on public roads.
• Maintain proper tire pressure for load and conditions.
• Follow recommendations in operator’s manual.

Safety Labels Text
WARNING WARNING
M171200—UN—17SEP13

• No more than two passengers in rear seat.
• Passenger must be able to grasp handholds with seat MXT015594—UN—17SEP15
belt on and both feet on floor. Avoid Injury from Falling
nets. This safety equipment must be used by all • Do not sit on toolbox.
occupants. • Do not exceed maximum toolbox door load of 50 lb
• Wear helmets when driving aggressively, on rough or (22 kg)
• Keep arms and legs inside during use.
WARNING
WARNING

WARNING
MXAL44310—UN—28MAR13
Avoid Injury or Death From Falling Off

Do not ride in cargo box or on cargo racks.
Cargo rack max weight: 200 lb (91 kg).


Safety Labels No-Text
Safety Label Location
A — Avoid Injury or Death From Falling Off - M165365 I — Avoid Injury From Explosion, Riders Can Fall Off and Be
B — Help Prevent Injury When Dumping Loads - M160919 Killed, Rollover or Falling Off May Cause Death - M161570
C — Prevent Equipment Fires - M160590 J — Prevent Equipment Fires - M165273
D — Park Machine Safely - M161018 K — Avoid Suffocation - Avoid Injury from Falling - M176639
E — Driver and Passenger Safety - M159667 (Installed on optional toolbox)
F — Hot Surface - GX21121 L — Avoid Injury or Death from Falling Off - M176918 (Installed on
G — Read Operator’s Manual, Avoid Tipping - M161511 optional toolbox)
H — Avoid Injury or Death From Rollover or Falling Off - M168539
10

Understanding The No-Text Machine Safety Help Prevent Injury When Dumping Loads
Labels
TCT005498—UN—11SEP12
At several important places on this machine safety signs

are affixed intended to signify potential danger. The
hazard is identified by a pictorial in a warning triangle. An
adjacent pictorial provides information how to avoid
personal injury. These safety signs, their placement on
the machine and a brief explanatory text are shown in
this Safety section.
There can be additional safety information contained on
parts and components sourced from suppliers that is not
reproduced in this operator’s manual.
Avoid Inujury or Death From Falling Off
• Operate dump with machine stationary and parking

M165365—UN—20SEP13 brake locked. Never dump while moving.
Do not ride in cargo box or on cargo racks. • Operate dump on level ground only.
Read Operator’s Manual to understand cargo rack • Operate dump from operator’s seat only.
maximum weight. • Do not place hands behind seat when lowering box.
• Refer to Operator’s Manual for correct load
distribution.
Prevent Equipment Fires
• Clean and inspect the entire machine.

• Carefully read Operator’s Manual Machine Cleanout
section for details.
11

Park Machine Safely Hot Surfaces
Keep away from hot surfaces.
Read Operator’s Manual
Before leaving vehicle:

• Stop engine
• Set park brake
• Remove key
• This operator’s manual contains important information

Driver and Passenger Safety necessary for safe machine operation.
• Carefully read operator’s manual before operating
machine. Observe all safety rules to avoid accidents.
Avoid Injury From Tipping

Avoid Serious Injury or Death

• Driver must be at least 16 years old with a valid driver
license.
• Never have more than the driver and one passenger
in the vehicle.
• Never have more than the driver and one passenger
in the vehicle.
• Passenger must be able to grasp handholds with
seatbelt on and both feet on floor.
Young Drivers Increase Chance of Death MXT008455—UN—27AUG13
• Young drivers may not be able to control vehicle. • Read operator’s manual.
• No drivers younger than 16 years old. • Drive slowly when turning.
• Always use brakes going down a slope. Vehicle can
takeoff (freewheel) downhill.
• No loads heavier than 1000 lb (454 kg). Spread load
evenly. Tie loads down.
• Reduce speed and load, on rough or hilly ground.
• Maintain 14 psi (97 kPa) tire pressure front and rear.
12

• Do not exceed gross vehicle weight rating 3100 lb Riders Can Fall Off and Be Killed
(1406 kg). Following loading instructions in operator’s
manual.
Avoid Injury or Death From Rollover or

Falling Off
M168539—UN—20SEP13
• Maximum of one person to a seat.
• No more than two passengers in rear seat. • No riders in box or anywhere else.
• Passenger must be able to grasp handholds with seat
belt on and both feet on floor.
• Vehicle is equipped with seatbelts and side doors or Rollover or Falling Off May Cause Death
nets. This safety equipment must be used by all
occupants.
• Keep arms and legs inside during use.
Avoid Injury From Explosion

• Read operator’s manual.

• Drive very slowly when turning.
• Always use brakes going down a slope. Vehicle can
takeoff (freewheel) downhill.
• Reduce speed and load on rough or hilly ground.
Avoid Injury from Falling

• Do not place gas container inside cargo box bed when

filling.
• Place gas container on ground when filling.
• Do not sit on toolbox.
13

• Do not exceed maximum toolbox door load of 50 lb
(22 kg)

OPS/ROPS Protective Structure Safety and

Certification Label
MXT012786—UN—22DEC14
One label is installed on your machine depending upon your region.
OCCUPANT PROTECTIVE STRUCTURE

To maintain occupant protection and OPS certification:
• Replace damaged OPS and worn seat belts. Do not
repair or revise.
• Any alteration of OPS must be approved by
manufacturer.
CERTIFICATION
Performance certified to: SAE J2194
John Deere Gator™ HPX
John Deere Gator™ XUV
Deere & Company Moline, Illinois, U.S.A.
14

Safety
Supervisor Safety Responsibilities • The operator should always make sure that the
• Make sure all operators of this machine are thoroughly passenger is aware of correct safety procedures while
trained and are familiar with the operator’s manual and riding in the utility vehicle.
understand the machine warning labels. • Use the correct flags, lights, signs and reflectors on
• Be sure to establish any special safety procedures for the vehicle to warn other drivers when operating near
existing work conditions and train operators in those roadways. Make sure these features are clean and
procedures. visible for 152 m (500 ft.).
• Supervisors, operators and mechanics should be • The passenger should always use the hand holds.
familiar with and practice the safety standards that • On machines with seat belts, to avoid serious injury,
apply to this machine. always ensure that occupants have safely secured
their seat belts prior to starting this vehicle.
• Horseplay can lead to accidents, severe bodily injury
Operator Training Required or death. Do not attempt stunts, jumps, or quick
acceleration to raise front wheels off the ground.
• Read the operator’s manual and other training
These actions can result in accidents or vehicle
material. If the operator or mechanic cannot read overturns.
English, it is the owner’s responsibility to explain this
material to them. This publication is available in other • Sit on the center of the seat and keep both feet within
languages. the foot platform perimeter. Clean foot platform if dirty,
and remove any debris from around foot controls.
• Become familiar with the safe operation of the
equipment, operator controls, and safety signs. • Check for debris in engine compartment, especially
around exhaust system components.
• All operators and mechanics should be trained. The
owner of the machine is responsible for training the • Always use both hands for steering.
users. • Know location of controls and how and what they
• Never let children or untrained people operate or operate.
service the equipment. Local regulations may restrict • Never operate utility vehicle while standing.
the age of the operator. • Never operate utility vehicle with the cargo box raised.
• The owner/user can prevent and is responsible for • Check brake action before beginning vehicle
accidents or injuries occurring to themselves, other operation. Adjust or service the brakes as necessary.
people, or property.
• To provide adequate braking ability and traction, do
• Operate the machine in an open, unobstructed area not tow any attachment or loaded trailer unless the
under the direction of an experienced operator when cargo box is fully loaded.
training.
• Do not allow the Gross Vehicle Weight (GVW) to
exceed the Gross Vehicle Weight Rating (GVWR) of
the vehicle.
Operating Safely • Before shifting into reverse, always check for
• Read, understand and follow all instructions in the obstacles or people behind the machine.
operator’s manual, on the machine and on the safety • Always back slowly.
video before starting.
• Inspect vehicle before operating. Be sure hardware is
• Misuse can lead to accidents, severe bodily injury or tight. Repair or replace damaged, badly worn, or
death. missing parts. Be sure guards and shields are in good
• The utility vehicle’s tires are designed for off-road use condition and fastened in place. Make any necessary
only. Paved surfaces may seriously affect handling adjustments before operating.
and control of the vehicle. If you must operate on a • Do not leave vehicle unattended when it is running.
paved surface, travel slowly and do not make sudden
turns or stops. • Operate during daylight or with good artificial light and
if you drive at night, use the lights.
• Do not operate this vehicle on a frozen body of water.
The vehicle could break through the ice, causing injury • Do not operate vehicle if under the influence of alcohol
or even death. or other drugs.
• Go slowly and be extra careful when riding on snow- • Avoid sudden starts, stops, or turns.
covered or ice-covered terrain. • Always use a level turn-around area.
• Slow down and be careful of traffic when operating • Do not wear radio or music headphones. Safe service
near or crossing roadways. Use care when and operation require your full attention.
approaching blind corners, shrubs, trees, or other
objects that may obscure vision.
15

Safety
Using a Spark Arrestor • This utility vehicle should not be operated by anyone
The California Public Resources Code, section 4442.5 under the age of 16 years.
provides as follows: • This utility vehicle should not be operated by anyone
without a valid driver license.
No person shall sell, offer for sale, lease, or rent to any
person any internal combustion engine subject to • Young drivers may not be physically able to control the
Section 4442 or 4443, and not subject to Section 13005 machine or may not be mature enough to make safe
of the Health and Safety Code, unless the person driving decisions.
provides a written notice to the purchaser or bailee, at the • Do not allow children to ride as a passenger in this
time of sale or at the time of entering into the lease or vehicle. Children may not be able to sit safely in the
rental contract, stating that it is a violation of Section passenger seat and use handholds properly.
4442 or 4443 to use or operate the engine on any forest- Passengers must be able to grasp handholds with
covered, brush-covered, or grass-covered land unless their back against the seat, seat belt on, and both feet
the engine is equipped with a spark arrestor, as defined on the floor.
in Section 4442, maintained in effective working order or • Passenger should always use the handholds while the
the engine is constructed, equipped, and maintained for vehicle is moving.
the prevention of fire pursuant to Section 4443. Cal. Pub.
• The seat belt installed on utility vehicles with an
Res. Code 4442.5. Occupant Protective Structure (OPS) is not designed
Other states or jurisdictions may have similar laws. A to restrain a child.
spark arrestor for your machine may be available from • Never carry passengers, especially children, in the
your authorized dealer. An installed spark arrestor must cargo box area. Do not tow children in a cart or trailer.
be maintained in good working order by the operator.
• Never assume that children will remain where you last
saw them. Stay alert to the presence of children.
• Before backing or turning, look behind and around the
Parking Safely utility vehicle for children.
1. Stop vehicle on a level surface, not on a slope. • Be alert at all times, drive forward and in reverse
carefully. People, especially children, can move
2. Fully lower the cargo box and any attachments on quickly into an area of operation.
the machine that can be lowered.
• Use extra care when coming to blind corners, shrubs,
3. Lock park brake. trees, or other objects that may block vision.
4. Stop engine. • Misuse and recreational riding can lead to accidents,
severe bodily injury or death.
5. Remove key.
6. Before you leave the operator’s seat, wait for engine
and all moving parts to stop. Avoid Excessive Speeds
7. Disconnect the negative battery cable or remove the
spark plug wires (for gasoline engines) before
servicing the machine.
Protect Children/Small Adults and Prevent
Accidents • Always wear a helmet when traveling at high speeds.
• Always travel at a speed that is safe and proper for the
terrain, visibility and operating conditions, and your
experience operating the machine.
• Use caution when operating the machine in reverse.
Use a slow speed and do not make sharp turns.
Always look behind before backing.
• Never travel at excessive speeds on slopes, either
going up or down. Use a slow speed and do not make
sharp turns. Become experienced driving the machine
on small slopes before driving on larger hills.
16

Safety
Avoid Tipping • Inspect seat belt and mounting hardware at least once
a year. Look for signs of loose hardware or belt
damage, such as cuts, fraying, extreme or unusual
wear, discoloration, or abrasion. Replace only with
John Deere-approved replacement parts.
• Layers of heavy clothing can interfere with proper
MXAL43279—UN—15MAR13 positioning of the seat belt and can reduce the
Accidents resulting in serious injury or death can occur effectiveness of the seat belt.
from tipping the utility vehicle. Observe the following
practices to help prevent accidents and always wear a
helmet when operating this vehicle in an aggressive Keep Occupant Protective System (OPS)
manner or on uneven or rough terrain. Installed Properly
• Drive very slowly when turning. Sharp turns could • Never operate the machine without the OPS installed.
cause the utility vehicle to tip over. • Make certain all parts of the OPS are installed
• Reduce speed and exercise extreme caution on correctly if the OPS structure is loosened or removed
slopes or on rough ground. for any reason. All OPS hardware should be tightened
• Do not overload vehicle and avoid shifting loads. to the proper torque per manufacturer’s
Reduce load when operating over rough or hilly recommendations.
terrain. • Any alteration of the OPS must be approved by the
• Do not stop or start suddenly when going uphill or manufacturer. The protection provided by the OPS will
downhill. Be especially cautious when changing be impaired if the OPS is subjected to structural
direction on slopes. damage, is involved in an overturn incident, or is in
any way altered by welding, bending, drilling, or
• Stay alert for holes, rocks, and other hidden hazards cutting.
in the terrain.
• Never attempt to repair a damaged or altered OPS. It
• Keep away from drop-offs, ditches, embankments, as must be replaced to maintain the manufacturer’s
well as ponds and other bodies of water. The machine certification of the structure.
could suddenly roll over if a wheel goes over the edge
of a cliff or ditch or if the edge caves in.
• Keep front wheels straight at crest of hill or going over
bumps. Keep Riders Off Vehicle
• When descending a hill, remove foot from accelerator
pedal and apply brakes to reduce speed and maintain
control.
• Do not make unauthorized changes or modifications
to the utility vehicle.
• This list of potential overturning hazards is not
exhaustive. • Seating is provided for operator and one adult
passenger.
• Never allow riders in the cargo box or other areas
Use Seat Belt Properly where seats are not provided.
• Riders on vehicle are subject to injury such as being
struck by foreign objects or being thrown off of the
vehicle and severely injured or killed.
• Riders affect the operator’s ability to control the
vehicle as well as its center of gravity. Also, riders
MXAL43280—UN—15MAR13 could obstruct the operator’s view resulting in the
vehicle being operated in an unsafe manner.
• Use a seat belt when you operate with a Roll-Over
Protective Structure (ROPS) to minimize chance of
injury from an accident, such as an overturn.
Before Driving
• Never modify, disassemble or attempt to repair the
1. Clean foot platform if dirty, and remove any debris
seat belt.
from around foot controls. Sit on the center of seat
• Replace entire seat belt if mounting hardware, buckle, and keep both feet inside foot platform perimeter.
belt, or retractor show signs of damage.
2. Inspect utility vehicle for signs of wear or damage.
17

Safety
3. All safety equipment must be in good condition and • Follow the manufacturer’s recommendations for
fastened in place: weight limits for towed equipment and towing on
• Lights. slopes.
• Shields. • If you cannot back up a slope with a towed load, the
• Safety start devices. slope is too steep to operate on with the towed load.
Reduce the towed load or do not operate.
4. Before moving, check around utility vehicle, be sure
• Do not turn sharply. Use additional caution when
no one is near it.
turning or operating under adverse surface conditions.
5. Inspect mechanical condition of your vehicle before Use care when reversing.
each use to minimize chance of injury or being • Do not shift to neutral and coast downhill.
stranded. Remember, you can ride farther in an hour
• Secure towed loads before transporting.
than you can walk in a day.
Be sure to check condition of tires and wheels, wheel
hardware torque, and maintain proper tire pressure.
Driving On Rough Terrain
6. Securely anchor all loads.
Transport Loads Safely

• Be sure load is evenly distributed in cargo box.
• Do not load above load guard.
• Securely anchor all loads in cargo box. • Always wear a helmet when operating the vehicle on
• Reduce cargo box load when operating on rough or uneven or rough terrain.
hilly terrain. • Use existing trails. Avoid terrain such as dangerous
slopes and impassable swamps. Watch carefully for
bumps, holes, ruts, loose terrain, or other obstacles.
Using Front Attachments • Look ahead at terrain. Know what is coming and be
• Remove front attachments such as drawbar hitches, prepared to react. Be alert for hazards.
hitchmounted winches, or blades when operating on • Keep front wheels straight at crest of hill or going over
rough or uneven terrain. Front attachments may bumps.
contact the ground when operating on rough or
• Reduce speed according to trail, terrain, and visibility
uneven terrain which may cause loss of control or
conditions.
rollover.
• The passenger should always use the hand holds.
Towing Loads Safely With Utility Vehicle

• To provide adequate braking ability and traction,
Climbing Or Descending A Hill or Slope
weight of towed load (trailer plus cargo) must never
exceed the vehicle payload (operator plus passenger
plus cargo box load).
• Do not tow a load that exceeds the maximum
allowable towing load for this vehicle, as specified in
this operator’s manual.
• Stopping distance increases with speed and weight of
• Always use the brakes when going down slopes. The
towed load. Travel slowly and allow extra time and
utility vehicle can speed up (freewheel) going down a
distance to stop.
slope. Engine or clutch braking effect is minimal.
• Tow load at a speed slow enough to maintain control.
• Always descend hill or slope at slow speeds and in a
• Excessive towed load can cause loss of traction and controlled manner.
loss of control on slopes. Reduce towed weight when
• Balance loads evenly and secure them. Braking could
operating on slopes.
shift the load and affect vehicle stability.
• Never allow children or others in or on towed
• Sit on center of seat and keep both feet within foot
equipment.
platform.
• Use only approved hitches. Tow only with a machine
• Never drive past the limit of visibility. Slow down near
that has a hitch designed for towing. Do not attach
crest of hill until getting a clear view of the other side.
towed equipment except at the approved hitch point.
Never go over the top of any hill at a high speed. An
18

Safety
obstacle, sharp drop, another vehicle or person, could • Never cross any body of water where depth may be
be on the other side of the hill. unknown to the operator.
• Keep front wheels straight at crest of hill or going over • If you must ride through water:
bumps. - Cross at a designated route if possible. Choose a
• Do not stop or start suddenly when going uphill or course within the waterway where both banks have
downhill. Be especially cautious when changing a gradual incline. Cross at a point known to be safe.
direction on slopes. - Proceed at a slow steady speed to avoid
• If vehicle stops or loses power going up a hill, lock submerged obstacles and slippery rocks.
park brake to hold vehicle on slope. Maintain direction - Avoid water crossings where the operation of a
of travel and release brake slowly. Back straight down utility vehicle may cause damage to waterway beds
hill slowly while maintaining control. Do not turn or erode waterway shoreline.
vehicle sideways. Vehicle is more stable in a straight • Stopping ability of vehicles with external brakes may
forward or rearward position. be affected after driving through water. If necessary,
• When descending a hill, remove foot from accelerator apply brakes several times to dry them out.
pedal and apply brakes to reduce speed and maintain • If water levels exceed the floorboard height at any
control. time, contact your dealer to have the engine,
• The vehicle has a limited amount of engine braking transmission, differential fluids, and fuel tank checked
that can assist when going down a hill or slope, but it for contamination.
is highly recommended to remove foot from throttle • If the engine stops during water crossing, do not re-
pedal and to use service brakes during descent as start the engine. Major engine damage can result if the
well. machine is not thoroughly inspected. Take the vehicle
• If the vehicle is freewheeling (engine braking is not to your dealer before starting the engine.
engaged), use the service brakes to slow vehicle • If you must continue to operate the vehicle prior to
travel. Do not reengage engine braking (do not dealer inspection, perform the following inspection
depress the throttle pedal) when freewheeling as that and service:
may cause the vehicle to skid. a. Move the vehicle to dry land, or at the very least to
water below the floorboard.
b. Dry any water present in the air intake. Clean the
Driving Across Slopes air filter. Filter replacement is required if water is
present.
c. Remove the spark plugs, keeping plug wires away
from the spark plug mounting hole to avoid igniting
fuel that may be in the cylinder. Turn the engine
over several times using the electric start.
d. Dry the spark plugs and reinstall, or replace with
• Reduce speed and use caution on slopes and in sharp new plugs.
turns. e. Attempt to start the engine. If necessary, repeat
• Stay alert for holes, rocks and other hidden hazards in the drying procedure. If engine does not start after
the terrain. three attemps, discontinue trying.
• When riding on soft terrain, turn front wheels slightly f. After driving through water when the air
uphill to keep utility vehicle on a straight line across temperature is below freezing, clear the brake
the hill. system of excess water, snow, mud or other
• If utility vehicle begins to tip, turn front wheel downhill material to prevent freezing.
to gain control before proceeding.
g. If water has been ingested into the clutch
enclosure, remove the drain plug to allow water to
drain, then reinstall the plug. Run the engine for
Riding Through Water one minute to dry the drive belt. In Neutral, run
• Driving through water can contaminate the power train engine up to full speed and back down several
and electrical systems resulting in long-term vehicle times to help dry the clutch sheave faces.
damage.
h. Take the vehicle to your dealer for service as soon
• Your vehicle is capable of driving through still water in as possible, whether you succeed in starting the
depth equal to the floorboard height. engine or not. It is critical that services are
• Never drive through deep or fast flowing water. The performed to the engine, transmission, differential
vehicle may become unstable and difficult to control. fluids, and fuel tank to check for contamination.
19

Safety
Checking Wheel Hardware • Keep hands, feet, clothing, jewelry, and long hair away
• A serious accident could occur causing serious injury from any moving parts, to prevent them from getting
if wheel hardware is not tight. caught.
• Check wheel hardware tightness often during the first • Disconnect battery(ies) or remove spark plug wires
100 hours of operation. (for gasoline engines) before making any repairs.
• Wheel hardware must be tightened to specified torque • Keep all nuts and bolts tightened.
using the proper procedure anytime it is loosened. • Securely support any machine elements that must be
raised for service work. Lock service latches before
working on machine with raised attachments.
Wear Appropriate Clothing • Never run engine unless park brake is locked.
• Keep all parts in good condition and properly installed.
Fix damage immediately. Replace worn or broken
parts. Replace all worn or damaged safety and
instruction decals.
• To prevent fires, remove any buildup of grease, oil, or
MXAL41935—UN—18FEB13 debris from the machine, especially the engine.
• Do not modify machine or safety devices.
• Always wear an approved helmet when operating the Unauthorized modifications may impair its function
vehicle in an aggressive manner, on rough or uneven and safety.
terrain, or at higher speeds. • Do not wear radio or music headphones while
• Helmets should fit properly and be approved for servicing the machine. Safe service requires your full
motorcycle use on standard roadways by the attention.
appropriate governing organizations for the region in • Disconnect battery ground cable(s) (-) on the machine
which the vehicle is being used. or remove attachment from machine before welding
• Wear close fitting clothing and safety equipment on the machine.
appropriate for the job.
• Certain operating conditions may dictate that the
operator and any passenger wear appropriate safety Prevent Fires
equipment while operating the vehicle. Be prepared • Please review these recommendations with all
for any existing and potential conditions before operators. See your John Deere dealer with
operating machine. questions.
• Local safety or insurance regulations may require • Always follow all safety procedures posted on the
additional safety equipment such as eye protection or machine and in this operator manual. Before carrying
a hard hat. out any inspection or cleaning always shut off engine,
• Always wear substantial footwear and long trousers. set parking brake and remove ignition key.
Do not operate the equipment when barefoot or • Besides routine maintenance, one of the best ways to
wearing open sandals. keep your John Deere equipment running efficiently
and to reduce fire risk is to regularly remove debris
buildup from the machine.
Practice Safe Maintenance • After operating, allow machine to cool in an open area
before cleaning or storing. Do not park machine near
flammable materials such as wood, cloth or
chemicals, or near an open flame or other sources of
ignition, such as a water heater or furnace.
• Completely remove any combustible materials from
equipment before storing, by emptying any grass
MXAL41933—UN—18FEB13
catcher bags, containers and cargo boxes.
• Only qualified, trained adults should service this • Debris can accumulate anywhere on the machine,
machine. especially on horizontal surfaces. Remove grass and
debris completely from engine compartment, muffler
• Understand service procedure before doing work. area, and from on top of the mower deck both before
Keep area clean and dry. and after operating machine. Additional cleaning may
• Never lubricate, service, or adjust machine while it is be necessary when mowing or mulching in dry
moving. Keep safety devices in place and in working conditions.
condition. • In addition to cleaning machine before using and
storing, keeping engine area clean provides the
20

Safety
greatest impact on fire prevention. Other areas a tire explosion. Welding can structurally weaken or
requiring regular inspection and cleaning include deform the wheel.
behind wheel rims, wire harness, hose or line routing, • When inflating tires, use a clip-on chuck and extension
mowing attachments, etc. Compressed air, leaf hose long enough to allow you to stand to one side
blowers, or high pressured water assists in keeping and NOT in front of or over the tire assembly.
these areas clean.
• Check tires for low pressure, cuts, bubbles, damaged
• Frequency of these inspections and cleaning will vary rims or missing lug bolts and nuts.
depending on a number of factors including operating
conditions, machine configuration, operating speeds
and weather conditions particularly dry, hot and windy
conditions. When you are operating in these Use Electronic Display Properly
conditions, inspect and clean these areas frequently Electronic Displays are secondary devices intended to
throughout the day. aid the operator in performing field operations, increase
• Excess lubrication or fuel/oil leaks or spills on the comfort and provide entertainment. Displays can offer a
machine can also serve as collection sites for debris. wide range of functionality, are used in many different
Prompt machine repair and oil and fuel clean-up machine system applications and can be used with other
reduces the potential for debris collection. secondary devices such as handheld electronic devices.
• Bearing failures or overheating can result in a fire. To A secondary device is any device that is not required to
reduce this risk, always follow the instructions in the operate your machine for its primary use. The operator is
machine operator’s manual regarding lubrication always responsible for safe operation and control of the
intervals and locations. Contact your local dealer if machine.
you have any questions about the lubrication intervals
To prevent injury while operating the machine:
or location and if any unusual noises are coming from
areas where bearings might be located. Washing the • Position the display according to the installation
machine while warm may also reduce bearing life and instructions. Ensure the device is secured and does
increase potential for premature bearing failure. not obstruct the driver’s view or interfere with the
• Always shut off fuel when storing or transporting machine operating controls.
machine, if the machine has a fuel shutoff. • Do not become distracted by the display. Stay alert.
• Check fuel lines, tank, cap, and fittings frequently for Pay attention to the machine and surrounding
cracks or leaks. Replace if necessary. environment.
• Do not change settings or access any functions that
require prolonged use of the display controls while
Do Not Modify Machine machine is moving. Stop the machine in a safe
location and place in park position before attempting
Do not make any unauthorized modifications to the such operations.
machine in any way.
• Never set the volume so high that you cannot hear
Modifications can result in making the machine unstable, outside traffic and emergency vehicles.
increasing the possibility of rollover causing severe
bodily injury or death. To promote safe operation, certain functions of displays
may be disabled unless the machine movement is
restricted and/or has been placed in the park position.
Overriding this safety feature may violate applicable law
Tire Safety and can result in damage, serious injury or death.
Only use available display functionality when conditions
permit you to do so safely and in accordance with
instructions provided. Always observe safe driving rules,
state or local laws and traffic regulations when using any
secondary device.
Explosive separation of a tire and rim parts can cause

serious injury or death:
• Do not attempt to mount a tire without the proper
equipment and experience to perform the job.
• Always maintain the correct tire pressure. Do not
inflate the tires above the recommended pressure.
Never weld or heat a wheel and tire assembly. The
heat can cause an increase in air pressure resulting in
21

Safety
Handling Fuel Safely • For gasoline engines, do not use gas with methanol.
Methanol is harmful to your health and to the
environment.
Handling Waste Product and Chemicals

Waste products, such as, used oil, fuel, coolant, brake
fluid, and batteries, can harm the environment and
people:
• Do not use beverage containers for waste fluids -
someone may drink from them.
• See your local Recycling Center or authorized dealer
to learn how to recycle or get rid of waste products.
• A Material Safety Data Sheet (MSDS) provides
To avoid personal injury or property damage, use specific details on chemical products: physical and
extreme care in handling fuel. Fuel is extremely health hazards, safety procedures, and emergency
flammable and fuel vapors are explosive: response techniques. The seller of the chemical
• Extinguish all cigarettes, cigars, pipes, and other products used with your machine is responsible for
sources of ignition. providing the MSDS for that product.
• Use only an approved fuel container. Use only non-
metal, portable fuel containers approved by the
Underwriter’s Laboratory (U.L.) or the American Use Electronic Display Properly
Society for Testing & Materials (ASTM). If using a Electronic Displays are secondary devices intended to
funnel, make sure it is plastic and has no screen or aid the operator in performing field operations, increase
filter. comfort and provide entertainment. Displays can offer a
• Never remove the fuel tank cap or add fuel with the wide range of functionality, are used in many different
engine running. Allow engine to cool before refueling. machine system applications and can be used with other
• Never add fuel to or drain fuel from the machine secondary devices such as handheld electronic devices.
indoors. Move machine outdoors and provide A secondary device is any device that is not required to
adequate ventilation. operate your machine for its primary use. The operator is
• Clean up spilled fuel immediately. If fuel is spilled on always responsible for safe operation and control of the
clothing, change clothing immediately. If fuel is spilled machine.
near machine, do not attempt to start the engine but
To prevent injury while operating the machine:
move the machine away from the area of spillage.
Avoid creating any source of ignition until fuel vapors • Position the display according to the installation
have dissipated. instructions. Ensure the device is secured and does
• Never store the machine or fuel container where there not obstruct the driver’s view or interfere with the
is an open flame, spark, or pilot light such as on a machine operating controls.
water heater or other appliance. • Do not become distracted by the display. Stay alert.
• Prevent fire and explosion caused by static electric Pay attention to the machine and surrounding
discharge. Static electric discharge can ignite fuel environment.
vapors in an ungrounded fuel container. • Do not change settings or access any functions that
• Never fill containers inside a vehicle or on a truck or require prolonged use of the display controls while
trailer bed with a plastic liner. Always place containers machine is moving. Stop the machine in a safe
on the ground away from your vehicle before fueling. location and place in park position before attempting
such operations.
• Remove fuel-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible, • Never set the volume so high that you cannot hear
then refuel such equipment with a portable container, outside traffic and emergency vehicles.
rather than from a fuel dispenser nozzle.
To promote safe operation, certain functions of displays
• Keep the nozzle in contact with the rim of the fuel tank may be disabled unless the machine movement is
or container opening at all times until the fueling is restricted and/or has been placed in the park position.
complete. Do not use a nozzle lock-open device. Overriding this safety feature may violate applicable law
• Never overfill fuel tank. Replace fuel tank cap and and can result in damage, serious injury or death.
tighten securely.
Only use available display functionality when conditions
• Replace all fuel container caps securely after use. permit you to do so safely and in accordance with
22

Safety
instructions provided. Always observe safe driving rules,
state or local laws and traffic regulations when using any
secondary device.
23

Machine Cleanout
Cleanout Areas
Primary areas that must be inspected and cleaned on the
machine include (See Safety Label Section):
2. Engine intake screens (F), and radiator cooling fins

(G).
3. Between engine (H) and skid plates (I) (if equipped).
1. Exhaust manifold (A) and shields (B), muffler pipes

(C), muffler (D) and muffler shield (E).
24

Machine Cleanout
4. On or near transmission (J) and driveline (K).
5. Battery (L) and related wiring harnesses.
25

Operating Controls
Operator Station Controls
Some controls may not be installed on your machine.
Key Description Key Description

A Turn Signal Switch I Transaxle Shift Lever
B Cargo Box Power Lift Switch J Traction Assist (Differential Lock) Lever
C 2WD / 4WD Switch K Fuel Tank Cap
D Front Blade Lift/Lower Switch L Park Brake Lever
E Headlight Switch M Accelerator Pedal
F Horn Switch N Brake Pedal
G Hazard Lights Switch O Ignition Key Switch
H 12V DC Accessory Outlet
26

Operating
Daily Operating Checklist Using Doors or Nets
❏ Test safety systems. CAUTION: Do not operate vehicle with doors or
❏ Check tire pressure. nets removed. Always park vehicle safely before
❏ Check fuel level. opening door or net to exit.
❏ Check engine oil level.
❏ Remove grass and debris from engine compartment, Using Doors
muffler area, and front grille, before and after Entering vehicle:
operating machine.
❏ Check area below machine for leaks.
❏ Check brakes and park brake operation.
❏ Inspect driveline CV boots for tears or punctures.
❏ Check coolant level.
❏ Check brake fluid level.
❏ Check air restriction indicator.
❏ Tighten any loose hardware.
❏ Check seat belt function.
Avoid Damage to Plastic and Painted

Surfaces
• Do not wipe plastic parts unless rinsed first.
• Insect repellent spray may damage plastic and
painted surfaces. Do not spray insect repellent near
machine.
1. Pull handle (A) toward you to unlatch and open door.
• Be careful not to spill brake fluid on machine
components. Brake fluid may damage painted 2. After entering the vehicle, check to be certain the
surfaces. Wipe up spilled brake fluid immediately. door is securely latched.
• Be careful not to spill fuel on machine. Fuel may Exiting vehicle:
damage surface. Wipe up spilled fuel immediately.
1. Park vehicle safely.
2. Pull handle (A) toward you to unlatch and open door.

3. After exiting the vehicle, check to be certain the door
is securely latched.
27

Operating
Using Nets Using Hand Holds
Entering vehicle:
1. Move net rearward out of entry and exit area, and
enter vehicle.
MXT008444—UN—27AUG13 MXAL44327—UN—28MAR13
Hand holds are provided for passenger balance.

2. Move net forward and insert metal tab of net into • When a front passenger is present, they shall use two
buckle (A) until it latches. of the three hand holds at all times while the machine
3. After entering the vehicle, check to be certain the net is moving: the dash bar (A), OPS handle (B), and side
is securely latched. rail (C).
Exiting vehicle: • When a rear passenger is present, they shall use one
of the two hand holds at all times while the machine is
1. Park vehicle safely. moving: the seat handle (D) or side rail (E).
2. Push button to release metal tab from buckle (A).
3. Move net rearward out of entry and exit area, and Using Bench Seat
exit vehicle.
If a bench seat is installed, it is not adjustable.
See SERVICE MISCELLANEOUS for instructions to
install and remove bench seat.
Using Bucket Seats

Adjusting Operator Seat
1. Stop machine and move transaxle shift lever to N
(neutral) position.
2. Lock park brake.
28

Operating
CAUTION: Never adjust seat while machine is 6. Tighten seat bracket hardware to specification.
moving. Stop machine before adjusting seat to Specification
prevent loss of machine control. Bracket Hardware — Torque . . . . . . . . . . . . . 10 N·m (7.4 lb-ft)
Using Seat Belt

NOTE: Shoulder harness is sensitive. An emergency
lock device is built into the belt for your protection.
To engage harness, pull harness slowly.
Attempting to pull too fast or in a jerking motion will
engage the locking mechanism and the harness
will not release.
Periodically inspect seat belts for wear or damage. See

Inspecting Seat Belt in SERVICE MISCELLANEOUS.
3. Push lever (A) to the left.

4. Slide seat forward or rearward to desired position.
5. Release lever.
Adjusting Passenger Seat

1. Tip seat forward.
Fasten Belt
1. Grasp outer seat belt connector (A) from behind
seat, pull out and across body to inner connector (B),
Front position shown. at inside of seat.
2. Hold onto seat and remove cap screws (A). 2. To adjust outer connector for best fit, squeeze the
upper (C) and lower (D) halves of outer connector
3. Slide seat to the rearward (B) or forward (C) position. together and adjust connector up or down along belt.
4. Position bottom of seat against bracket and align 3. Push outer connector firmly into inner connector until
correct holes with holes in seat. it locks.
5. Install original hardware to secure seat.
29

Operating
Release Belt 6. Move transaxle shift lever to reverse position.
1. Press red button on inner connector to release seat 7. Turn key switch to START position. Engine should
belt. not crank. Turn key switch to STOP position.
Testing Safety Systems Using Park Brake

NOTE: The park brake alarm will buzz if the machine is in
gear and you try to move in forward or reverse
before unlocking the park brake.
CAUTION: Children or bystanders may attempt
to move or operate an unattended machine.
Always lock the park brake and remove the key
before leaving the machine unattended.
IMPORTANT: Damage to brake will occur if machine
travels with brake locked.
Unlock park brake before before beginning
machine travel.
CAUTION: Avoid injury! Engine exhaust fumes Locking the Park Brake:
contain carbon monoxide and can cause 1. Push down on brake pedal to hold machine in place.
serious illness or death.
2. Pull up on lever to engage park brake.
Do not run an engine in an enclosed area, such
as a garage, even with doors or windows Unlocking the Park Brake:
opened.
1. Push down on brake pedal to hold machine in place.
Move the machine to an outside area before
running the engine. 2. Pull up on lever.
3. Press center button on lever, and release lever down
The safety systems installed on your machine should be completely.
checked before each machine use. Be sure you have
read the machine operator manual and are completely
familiar with the operation of the machine before Using Travel Controls
performing these safety system checks.
1. Stop machine.
Use the following checkout procedures to check for
normal operation of machine. 2. Allow engine to come to a low idle speed.
If there is a malfunction during one of these procedures, IMPORTANT: Do not shift gears when vehicle is
do not operate machine. See your authorized dealer moving or with engine running above low idle
for service. speed. Push down brake to stop vehicle motion
and engage shift lever with a firm positive
Perform these tests in a clear open area. Keep action.
bystanders away.
Gears may grind when shifting if engine idle
speed is set higher than factory specification.
Testing the Safety Start System NOTE: Always shift into low range when operating on
1. Sit on the operator’s seat. wet or uneven terrain, or when towing or pushing
2. Put key switch in STOP position. heavy loads.
3. Lock park brake.

4. Move transaxle shift lever forward to the high range
position.
5. Turn key switch to START position. Engine should
not crank. Turn key switch to STOP position.
30

Operating
B - RUN Position - Turn key from STOP to this position
and all switched power circuits will be on. If installed,
electric power assist steering will activate.
C - START Position - Turn key to START position to
crank the engine. Release key after engine has started
and it will automatically return to the RUN position. The
engine will continue to run.
Using Headlights
Ignition key switch must be in the RUN position to
operate the lights. If the ignition key switch is in the RUN
position and the engine is not running, the battery will
discharge if the lights are allowed to remain on for an
extended period of time.
• Press top of light switch to turn headlights on.
NOTE: Be sure to turn lights off and turn the ignition key
switch to STOP position, or lights will discharge
battery.
3. Select a gear position:
• Forward - Push shift lever (A) forward to either
• Press bottom of light switch to turn headlights off.
high (B) or low (C) range.
• Reverse - Push shift lever rearward to reverse (D)
gear.
Using Instrument Display
4. Look in the direction the machine will travel.
NOTE: Model number displays during machine start-up.
CAUTION: Reduce speed before braking or
Depending on machine model, some functions are
turning, when hauling loads, and while
not available.
operating around obstacles or on hazardous off-
road conditions.
5. Push down accelerator pedal (E) slowly and

smoothly to begin machine travel.
6. Release accelerator pedal and apply brake pedal (F)
evenly and firmly to slow down or stop.
Using Ignition Key Switch
A - Turn Signal Lights - The left or right signal light

illuminates when activating turn signal switch while
ignition key switch is in RUN or STOP position. (NOTE:
The turn signal lights are active only if you have installed
an optional kit on your machine.)
B - RPM Indicator - This indicator shows engine RPMs.
C - Battery Discharge Light - This light illuminates when
Ignition key switch label.
the ignition key switch is in the RUN position and the
A - STOP Position - With key in STOP position, all engine is not running. If this light illuminates when the
switched power is off, and engine should not run. engine is running, see your John Deere dealer.
31

Operating
D - Engine Oil Pressure Light - This light illuminates stop machine and shut off engine. If light is active after
when the ignition key switch is in the RUN position and restart, contact your John Deere dealer.
the engine is not running. If this light turns on while the
O - Electric Power Assist Steering (EPAS) Indicator -
engine is running, engine oil pressure is too low. Stop
The level of assist decreases as the speed increases,
engine.
with full assist at zero speed. Normal steering operation
E - Engine Coolant Temperature Light - This light will has the EPAS indicator light off.
illuminate for several seconds after the ignition key
P - Speedometer - The speedometer indicates machine
switch is turned from the STOP position to RUN position.
speed in km/h or mph.
It illuminates when the coolant temperature reaches an
overheat condition. If this light flashes or remains on Q - Clock - The clock shows the current time.
during operation, remove load on machine immediately.
Ensure that fan is operating and that there is no blockage
of the radiator. Check coolant level only when radiator is
cool enough to touch with bare hands. Using Instrument Display Arrow Keys
1. Turn key to RUN position.
F - Seat Belt Indicator Light - This light illuminates if the
driver seat belt is not adequately secured.
G - Park Brake Light - Light illuminates when the ignition
key switch is in the RUN position and the park brake is
partially or fully engaged into the locked position.
H - Arrow Keys - These buttons are used to activate
certain instrument display functions. For detailed
instructions, see Using Instrument Display Arrow Keys in
OPERATING Section.
I - Gas Gauge - These bars display the current fuel level
in the fuel tank. Each bar displays approximately 1/8 of a
full fuel tank. If there is less than 1/8 of a tank (no bars
illuminated) the gas symbol blinks.
J - Trip Meter, Odometer, Hourmeter Indicator - This MXT008443—UN—27AUG13
indicator shows the accumulated kms/miles the machine
has accumulated, along with a trip meter. The hour meter
2. Push down arrow (A) to adjust display brightness.
portion shows the accumulated number of operating
hours the engine has run. The hour meter displays Odometer, Trip Meter and Hourmeter
operating hours with the ignition key switch in the RUN
position, and accumulates and displays operating hours Push up arrow (B) to toggle between odometer, trip
when the engine is running. The hour meter is intended meter, and hour meter.
to provide a means of monitoring machine usage for • When “ODO” (C) is displayed, odometer indicator (F)
maintenance purposes. Use the hour meter to determine displays the number of miles or km the machine has
when your machine has reached the recommended moved. (To change between miles or km displayed,
service intervals. see next step.)
K - 2WD/4WD Display - This light illuminates when the • When “TRIP” (D) is displayed, the indicator (F)
four-wheel drive is active. displays the number of miles or km the machine has
moved for a certain trip. (Press and hold the up arrow
L - Coolant Temperature Gauge - These lights display (B) for 3 seconds to change the display back to “0” for
the current engine temperature. If the temperature rises beginning a new trip.) (To change between miles or
to an overheat condition, the engine coolant temperature km displayed, see next step.)
light (E) illuminates.
• When hourmeter (E) is illuminated, the indicator (F)
M - Glow Plug Light (Diesel Engine Models Only) - displays the number of operating hours the engine has
This light illuminates when the key switch is placed in the run.
RUN position and the engine/glow plugs are cold. After
approximately 0-9 seconds, depending on temperature, Clock and Units
the light turns off. To set the clock or change units, the machine must be
stopped. Push and hold up arrow (B) and down arrow (A)
N - System Diagnostic Light (Gas Engine Models
for 3 seconds to change settings.
Only) - This light illuminates for up to 4 seconds when
ignition key switch is turned to the RUN position. The
light illuminates when sensors malfunction. If light is on,
32

Operating
NOTE: If you wait longer than 5 seconds before touching • Press at left end of turn signal switch to signal a left
either the up or down arrow, the display goes back turn.
to the main screen. Press and hold up and down • Press at right end of turn signal switch to signal a right
arrows for 3 seconds again to get back to the clock turn.
display and speed screens.
• Press at opposite end of turn signal switch until switch
is centered to turn signal light off.
1. Push up arrow (B) to change from 12 or 24 hr.
display.
2. Push down arrow (A) to set the clock. Press up arrow
to increase operating hour setting. Push down arrow
Using Hazard Lights (If Equipped)
(A) again to display minutes. Push up arrow to NOTE: Hazard lights will continue to flash when the
increase minute setting. (Press and hold up arrow for ignition key switch is in the STOP position,
approximately 2 seconds to have minute counter-run discharging the battery.
continuously. Release up button to stop minute
counter.) • Press at top of hazard light switch to turn hazard lights
3. Push down arrow (A) to select the speed units. Push on.
up arrow to select English (mph) or metric (km/hr), • Press at bottom of hazard light switch to turn hazard
changing the speed display, and also when showing lights off.
the odometer and trip displays.
4. Push down arrow (A) to select machine installed tire
size. Push up arrow to select 14, 25, 26 or 27 in. tire Using Front Blade Switch (If Equipped)
size diameter. • Press at top of front blade switch to raise blade.
5. Push down arrow again to exit display menu. • Press at bottom of front blade switch to lower blade.
Using Accessory Outlet Using Storage Areas

Up to three outlets may be installed depending upon your Under Machine Hood
machine model and seat options:
CAUTION: Never store flammable, heavy, or
• 5 amp outlet under center armrest loose breakable objects in the storage tray.
• 10 amp outlet on machine dashboard Always latch hood before operating machine.
• 15 amp outlet behind front passenger seat in front of
rear bench seat IMPORTANT: Do not store items that will not allow
CAUTION: Safe operation requires your full the hood to close properly. Properly secure
attention. Do not wear radio or music loose or sharp items. These items may damage
headphones while operating machine. the storage tray or other items within the tray.
NOTE: Accessory must be rated at given amps for outlet

or less.
The accessory plug does not turn off with the key
switch. Items connected to the accessory plug will
continue to draw power, discharging the battery.
1. Remove 12-volt outlet cover and install accessory

cord in outlet.
2. Install cover in outlet after use.
Using Turn Signal Switch (If Equipped)

NOTE: Turn signals will continue to flash when the
ignition key switch is in the STOP position,
discharging the battery. Storage tray (A) is located in front of machine under the
hood.
1. Open hood to access the storage tray.
33

Operating
2. Secure all items to prevent damage from movement Starting the Engine
while operating the machine.
CAUTION: Engine exhaust fumes contain
3. Close hood. carbon monoxide and can cause serious illness
or death.
Under Bench Seat
• Mo v e th e mac h ine to an o uts id e area b efo re
ru nn ing th e en gin e.
• Do no t run a n en gin e in an e nc lo s e d are a
without adequate ventilation.
• Connect a pipe ex tension to the engine
e x ha us t p ipe to d irec t th e ex ha us t fu mes o ut
o f th e are a.
• A llo w fres h o uts ide a ir in to the wo rk area to
clear the exhaust fumes out.
1. Sit on operator seat. Do not start engine at this time.
2. Push down on accelerator pedal to check free
movement of pedal assembly. Release pedal.
NOTE: The machine has a neutral start safety switch.
The engine will not start unless the transaxle shift
MXAL44338—UN—28MAR13 lever is in N (Neutral) position.
1. Tip seat and cargo rack back to access the storage 3. Verify that transaxle shift lever is in N (Neutral)
tray (A). position.
2. Secure all items to prevent damage from movement 4. Verify that park brake is locked.
while operating the machine. CAUTION: Do not start engine by shorting
3. Tip cargo rack and seat down. across starter terminals. Bypassing normal
circuitry will allow vehicle to start in gear.
Do not use starting fluid to aid engine starting.
Using Cargo Rack Never start engine while standing on ground.
Start engine only from operator’s seat.
1. Tip seat back to use the cargo rack.
5. Turn ignition key switch to the RUN position.
6. Check that indicator lights turn on briefly:
• All indicators on the instrument panel display.
• Steering malfunction light (machines with electric
power assist).
• Check that the oil pressure indicator remains on.
• Other indicators may also remain on while
starting.
7. Turn ignition key switch to START position.
IMPORTANT: Starter may be damaged if operated
continuously for extended periods of time.
Allow starter to cool down after several starting
attempts.
8. Release ignition key switch to the RUN position
when engine starts.
2. Arrange load so the weight is centered over the main • If engine does not start within five seconds, turn
cargo area (A). ignition key switch to STOP position and wait ten
seconds before trying to start again.
3. Secure load to the tie downs (B) in a safe and secure • In very cold conditions, attempt starting engine
manner. three times only, then wait 5 minutes before trying
34

Operating
again. This will allow time for starter to cool and The indicator light flashes a single flash to indicate low
prevent damage to starter. battery voltage. Check battery charge and condition.
IMPORTANT: Do not operate the engine at full throttle Three blinks indicates the EPAS has reached thermal
or under load until engine has warmed up, or protection limits. Avoid heavy steering (agressive
engine damage could occur. steering or turning against stops) and allow time for the
system to cool.
9. Run engine at half speed for 2 or 3 minutes to warm
If the indicator light remains on constantly or flashes
the engine.
continually during operation, contact your John Deere
dealer.
Steering effort is adversely affected by low tire air
Stopping Engine pressure. Always keep tires at recommended air
CAUTION: Children or bystanders may attempt pressure.
to move or operate an unattended machine.
Always lock the park brake and remove the key
before leaving the machine unattended. Using Traction Assist
Traction assist provides better traction when rear wheels
IMPORTANT: Do not stop engine immediately after start to slip. Engaging the traction assist will cause both
hard or extended operation. Keep engine rear wheels to turn together at equal speed.
running at low idle for about 2 minutes to CAUTION: Driving at high speeds with the
prevent heat build-up. traction assist engaged may result in loss of
steering control. Do not engage traction assist
1. Stop machine. or turn with the traction assist engaged while
2. Move transaxle shift lever to N (Neutral) position. operating machine at high speeds or on slopes.
3. Lock park brake.
4. Turn ignition key switch to STOP position. Engaging the Traction Assist:
5. Remove key. IMPORTANT: Incorrectly engaging traction assist

may damage the transaxle.
Reduce speed before engaging or disengaging
traction assist.
Emergency Stopping
1. Remove foot from travel pedal or accelerator pedal. 1. Stop or reduce engine speed to 1/3 throttle or less.
2. Depress brake pedal. Do not release brake pedal 2. Pull traction assist lever up to the locked (vertical)
until machine has stopped. position:
3. After machine has stopped, lock the park brake. • Traction assist will remain engaged as long as
lever is up (vertical).
4. Turn ignition key switch to STOP position.
Disengaging the Traction Assist
NOTE: To ensure true disengagement of traction assist,

Using Electric Power Assist Steering you must equalize torque on both axles.
(EPAS)
The Battery Discharge/Steering Malfunction Light will 1. Stop or reduce engine speed to 1/3 throttle or less.
indicate if there is a malfunction in power assist steering. 2. Drive the vehicle straight ahead at a constant speed.
The light may go off and on during operation as an 3. Push lever down to unlocked position.
indicator that EPAS has been reduced to protect the
system. The fault indication may be cleared
automatically when the fault condition is removed.
Using Four Wheel Drive
The level of assist decreases as the speed increases,
with full assist with zero speed. 4WD On-Demand enables the front wheels to drive, but
torque will not be applied until rear wheels begin to slip.
Normal steering operation has the EPAS indicator light
off.
35

Operating
CAUTION: 4WD On-Demand greatly increases Using the Cargo Box
traction and may make dangerously sloped CAUTION: Avoid injury! Seating is provided for
terrain accessible, increasing possibility of a tip- the operator and one passenger. Do not allow
over. riders in the cargo box or on the tailgate. Extra
Use extra caution when driving on slopes. Use riders can fall off and be seriously injured or
4WD On-Demand when driving on slopes to killed.
increase traction.
Use 4WD On-Demand when driving on icy, wet Raising and Lowering with Manual Lift
or graveled surfaces; reduce speed to avoid
skidding and loss of steering control. CAUTION: Avoid injury! Park machine on a level
surface and lock park brake before manually
raising and securing cargo box in raised
IMPORTANT: Engaging 4WD On-Demand when the position.
machine is stopped and the rear wheels are
spinning will damage the gears. A cargo box containing material is heavy.
Empty some or all material until cargo box can
• Push in on top of 2WD/4WD switch to enable the 4WD safely be raised manually.
On-Demand system.
• Push in on bottom of switch to disable the system. 1. Park the vehicle safely. (See Parking Safely in the
CAUTION: Front implements may cause SAFETY section.)
decreased traction at the rear wheels resulting
2. Empty cargo box by hand.
in loss of control. Always operate machine with
4WD On-Demand engaged when front 3. Disengage cargo box lock if installed.
implements are attached.
Tips for operating 4WD On-Demand:

NOTE: Occasionally the 4WD On-Demand system will
not disengage after a change in vehicle travel
direction. This is known as “wedging.” If this does
occur, the vehicle will exhibit higher than usual
steering efforts and driveline wind-up. To
disengage (un-wedge) the system, reverse the
direction of vehicle travel.
• Maintain recommended front and rear tire pressures

to ensure optimum performance on all surface
conditions.
• Disable 4WD On-Demand when driving machine on
paved or hard packed surfaces to increase front tire
life and reduce drive train wear. MXAL44170—UN—10APR13
4. To release pressure against latch (A), push down on

cargo box.
5. Release latch by pulling latch towards grip (B) on
cargo box. Allow lift cylinder to raise cargo box.
36

Operating
Raising and Lowering with Power Lift 3. Check to be sure that box is locked in raised position.
IMPORTANT: Avoid damage! A hydraulic “whine” or 4. To lower cargo box, push rod slightly toward center
squealing sound when cargo box is fully raised of box, and slowly push cargo box downward until it
or lowered or when box is heavily loaded latches in fully lowered position.
indicates that the power lift hydraulic overload
Operating the Tailgate
pressure relief valve has opened, and the
power lift can not apply any more force. To CAUTION: Avoid injury! Never operate tailgate
prevent unnecessary wear or damage, keep with one lanyard attached (always use both).
sound to a minimum. Do not operate the power
lift actuator beyond full stroke or exceed the Check condition of lanyards for wear or
cargo box weight capacity. damage. Replace if cable is kinked or frayed.
IMPORTANT: Avoid damage! Do not attempt to tilt or
1. Park the vehicle safely. (See Parking Safely in the dump cargo box when lanyards are detached.
SAFETY section.) Tailgate damage from contact with hitch
results.
2. Disengage cargo box lock if installed.
To avoid jamming material in the gap between
3. Turn key to RUN position. the cargo box bed and tailgate, keep lanyards
4. Raise the cargo box by pressing and holding the top attached when loading and unloading loose
of the cargo box power lift switch. Release switch materials.
when box is at desired dump height or when
reaching maximum height.
NOTE: Allowing the pressure relief valve to open slightly
(whine or squeal) after cargo box is fully lowered,
helps keep the cargo box secure and reduce
rattling caused by travel vibrations.
5. Lower cargo box by pressing and holding bottom of

cargo box power lift switch
6. Turn key to STOP position.
Locking Box in Raised Position
CAUTION: Avoid injury! If not secured properly,
cargo box falls. Remove key from ignition and
lock support rod securely before doing any
service under raised cargo box. 1. Check to be sure lanyards (A) are in place to support
lowered tailgate.
1. Raise the cargo box. 2. Disconnect lanyards if you want to lower tailgate
more than 90 degrees.
IMPORTANT: Avoid damage! Lower tailgate
completely to unload cargo box only. Never
drive with the tailgate hanging down. Tailgate
can contact tires and cause damage.
3. Pull back on handle (B) to unlock and lower tailgate.

4. Before raising tailgate, check for stones and debris
caught in the gap between the tailgate and cargo box
floor.
To remove debris:
a. Lock the cargo box in raised position.
b. Rotate the tailgate slightly to free debris, and
MXT011037—UN—08SEP14 brush out the gap.
c. Lower the cargo box.
2. Pull down on the cargo box slightly and push rod (A)
in toward center of box to lock bottom of rod (B) into 5. To raise tailgate, slowly push tailgate upward and
the slotted locked position (C). lock into closed position.
37

Operating
6. Check to be sure that tailgate is securely locked.
Using Cargo Box Tie Downs
3. Loosen loop (D) on top of lanyards, disconnect from

MXAL44173—UN—10APR13 studs on cargo box side, and lower tailgate fully
downward.
1. Arrange load so the weight is centered over the main
cargo area (A).
2. Secure loads to the tie-downs (B) in a safe and
secure manner.
Removing the Tailgate
4. Loosen two nuts (E) on rear of floor panel, to allow

side panels to be removed.
5. If equipped with tail lights, disconnect the wiring
1. Check to be sure lanyards (A) are in place to support harness and hang the harness in the rear of the box.
lowered tailgate.
2. Pull back on handle (B) to unlock and lower tailgate
(C).
38

Operating
Operating in Flat Bed Mode
CAUTION: Avoid injury! Cargo box load guard
protects operator and passenger from shifting
loads. Do not remove load guard.
6. From behind drivers seat in cargo box, remove two

nuts (F).
1. To operate machine in flat bed mode, remove tailgate

(A) (See Removing the Tailgate).
2. Remove left (B) and right (C) side body panels.
7. Loosen three bolts (G) in left side body panel (H). Do

not completely remove bolts from clamp-on nuts.
8. Support the tailgate to avoid bushing damage. Move
side body panel slightly outward and remove tailgate
from left side body panel and right side body panel
(I).
9. Install in reverse order of removal.
3. Arrange load so the weight is centered over the main
cargo area (D).
4. Install tailgate and side panels in reverse order of
removal procedure (See Removing the Tailgate).
Determining Vehicle Load Capacity

Find weights and capacities for your machine model in
SPECIFICATIONS.
39

Operating
CAUTION: Avoid injury! Overloading the vehicle operator, passenger (or passengers), trailer tongue,
or trailer causes loss of control and causes and attachments.)
serious injury or death. • Determine maximum vehicle load capacity:
• D o n o t a l l o w t h e G r o s s Ve h i c l e We i g h t ( G V W ) a. Calculate GVW = A+B+C+D+E
t o e x c e e d t h e G r o s s Ve h i c l e We i g h t R a t i n g b. Subtract the Gross Vehicle Weight (GVW) from the
(GV WR) of the v eh ic le. Gross Vehicle Weight Rating (GVWR).
• Remov e e x c es s weig ht be fo re op era ting c. The weight difference between the two numbers is
vehicle. the vehicle load capacity.
Vehicle Load Capacity = GVWR-GVW
d. The Gross Vehicle Weight must be less than or
equal to the Gross Vehicle Weight Rating. If GVW
exceeds GVWR, remove excess weight from
vehicle before operating.
Example:
The following is for a vehicle with 68 kg (150 lb.) of cargo
load, a 91 kg (200 lb.) operator, 100 kg (220 lb.) of
attachments. Attachments include a heavy-duty brush
guard, OPS poly roof, cargo box power lift kit; towing a
The picture shows an Occupant Protective Structure (OPS) installed on
a two-passenger machine. Some machines do not have an OPS trailer with 23 kg (50 lb.) of tongue weight.
installed as some models are not designed to include an OPS.
Find the correct specifications for your machine model in
Factors in Determining Vehicle Load Capacity the SPECIFICATIONS section in this manual. To
determine your machine capacity, use those numbers.
NOTE: Optional equipment, and attachments that are not
standard equipment, reduce your cargo box
capacity; so they must be included when Key Description
determining gross vehicle weight. (A) Operator Weight: 91 kg (200 lb.)
(B) Empty Vehicle Weight: 553 kg (1220 lb.)
• Gross Vehicle Weight (GVW) is the combination of (C) Trailer Tongue Weight: 23 kg (50 lb.)
the empty vehicle weight, payload, trailer tongue (D) Cargo Load: 68 kg (150 lb.)
weight, and the weight of any other kits or attachments (E) Attachments and/or Options: 100 kg (220 lb.)
on the vehicle.
GVW = A+B+C+D+E GVW = 835 kg (1840 lb.)
• Gross Vehicle Weight Rating (GVWR) is the • 91 kg (200 lb.) + 553 kg (1220 lb.) + 23 kg (50 lb.) + 68
maximum permissible vehicle weight. kg (150 lb.) + 100 kg (220 lb.)
• Payload is the weight of all occupants plus the cargo
Vehicle Load Capacity = 81 kg (180 lb.)
box load.
• (A) Occupant load is the combined weight of the • GWR 916 kg (2020 lb.) less GVW 835 kg (1840 lb.)
operator and passenger (or passengers). Utilize the remaining vehicle load capacity of 81 kg (180
• (B) Empty vehicle weight is the weight of the vehicle lb.) to haul an additional passenger (or passengers),
(full fluids) without occupants or load or attachments. cargo, trailer tongue, and attachment weight.
• (C) Trailer tongue weight is the weight measured if
the tongue of a loaded trailer was placed on a scale.
The tongue weight must be approximately 10% of the
total of the trailer weight and the weight of its load.
• (D) Cargo box load is the weight of the cargo in the
cargo box. It is less depending on the weight of the
occupants, attachments, and the trailer tongue weight.
• (E) Attachment and option weight is the combined
weight of all attachments and options that were not
standard equipment. For help with this information,
contact your John Deere dealer.
• Vehicle load capacity is the remaining amount of
weight that the vehicle is able to haul in the cargo box.
(Or cargo box plus the additional weight from the
40

Operating
Loading the Cargo Box Because there is a big difference in weight between dry
and wet sand, the only way of getting true weight of the
CAUTION: The utility vehicle may become load you are carrying is by using a scale.
unstable if the cargo box is loaded incorrectly.
Avoid loose and shifting loads or uneven Printed weight is normally on bagged and other material.
loading of material.
Box Volume Capacity
• Do no t lo ad a bo v e he igh t o f lo ad g ua rd .
• Se c u rely a nc hor a ll lo ads in c arg o bo x .
• D o n o t l o a d b e y o n d m a x i m u m c a p a c i t y.
MXAL44182—UN—10APR13 MXAL44184—UN—10APR13
See capacities in SPECIFICATIONS. Use rub rails (A) in left and right side panels, and form
Reduce load by half when operating over rough, hilly, or beads (B) in cargo box front panel to determine cargo
steep terrain. Do not overload vehicle. Limit loads to box volume.
those that can be safely controlled. • 10.1 cm (4 in.) load height (C) = 150 L (5.3 cu ft).
Reduce speed and exercise extreme caution when • 15.2 cm (6 in.) load height (D) = 226 L (8 cu ft).
operating over rough, hilly, or steep terrain. • 20.3 cm (8 in.) load height (E) = 303 L (10.7 cu ft).
Securely anchor and evenly distribute loads in cargo box, NOTE: Use table below to determine height of common
when loading objects into vehicle. Shifting loads will cargo box materials.
affect stability. Do not exceed Gross Vehicle Weight (GVW).
Do not load above load guard (A).
Material Weight (lbs/cubic Capacity Height
foot)
Asphalt 45 12
Brick 120 6
Cement (Dry) 94 8
Sand (Dry) 100 7
Sand (Damp) 120 6
Sandstone (Broken) 94 8
Concrete (Set/Mix) 135 5
Soil (Dry/Loose) 78 9
Soil (Wet/Packed) 100 7
Clay (Dry/Lump) 67 11
Clay (Wet/Lump) 100 7
Fertilizer 60 12
Gravel (1/4 - 2 in.) 105 7
Turf/Sod 35 12
Avoid concentrated loads at rear or side of cargo box to

prevent vehicle from tipping over. Be sure load is evenly
distributed.
41

Operating
Emptying Cargo Box • Do not tow a load that exceeds towing capacity listed
in SPECIFICATIONS.
CAUTION: Raising a loaded cargo box changes
the center of gravity. Keep vehicle a safe • Do not exceed trailer tongue weight listed in
distance from the edge of ravine or drop-off SPECIFICATIONS. (The tongue load of a trailer
when raising cargo box to empty. should be approximately 10% of the total trailer
weight.)
A loaded cargo box can be very heavy. Do not
• Tow load at a speed slow enough to maintain control.
attempt to manually raise a loaded cargo box.
Unload cargo box before raising it by hand. IMPORTANT: Avoid damage! When operating on
terrain with extreme angles, use a ball type
hitch (A).
1. Back up vehicle to dump site.

2. Park the vehicle safely. (See Parking Safely in the
SAFETY section.)
3. Open tailgate.
IMPORTANT: Stop emptying immediately if overload MXAL44186—UN—10APR13
pressure relief valve opens. Lower cargo box
completely and remove excess load by hand • Always use approved hitch and hitch point provided
before dumping. for the utility vehicle. Do NOT modify the hitch or hitch
point in any way.
4. Raise cargo box to dump load.
Capacity Label
5. Lower cargo box when empty.
6. Close tailgate. Do not drive vehicle with cargo box in
raised position.
Towing Loads
CAUTION: Avoid injury! Excessive towed load
can cause loss of traction and loss of control on
slopes. Stopping distance increases with speed
and weight of towed load.
Do not tow a load that exceeds the maximum
allowable towing load for this vehicle, as
specified in this operator’s manual.
Secure towed loads before transporting.
• To provide adequate braking ability and traction, MXT007935—UN—18JUL13

weight of towed load (trailer plus cargo) must never Labels shown are for reference only. Confirm capacities on labels on
exceed the vehicle payload (operator plus passenger your machine.
plus cargo box load). Your machine may have a hitch capacity label installed
• When operating over rough, hilly, or steep terrain and near the hitch area. The label indicates vertical and
reducing cargo load by half, any towed load should horizontal load capacities.
also be reduced accordingly.
42

Operating
The vertical load capacity is the maximum down force Transporting Machine
which can be applied for safe operation. The horizontal
load capacity is the total weight of what is being towed Towing the Machine
which must not be exceeded for safe operation.
IMPORTANT: Never tow the vehicle above 40 km/h
(25 mph). Towing a vehicle at speeds above 40
km/h (25 mph) will result in transmission
Using Correct Tires and Inflation damage.
CAUTION: Help prevent severe bodily injury or To avoid damage, haul the vehicle in an
death, failure to observe these enclosed trailer. If an open trailer must be used,
recommendations may result in loss of stability haul on a heavy-duty trailer or on a full-size
and operator control. truck. Be cautious and travel at reduced
speeds.
Optional accessories, such as a windshield,
See tire descriptions and inflation pressures for load
conditions in SPECIFICATIONS. should be removed to avoid sudden
unintentional separation from the vehicle.
Tires Never use a car type dolly with the front wheels
Use of John Deere approved original equipment or on the dolly.
optional equipment is recommended. To ensure
maximum machine performance and ride quality, do not 1. Check to be sure that the ignition key switch is in the
mix size, type, or placement of tires. Failure to place tires STOP position.
per the guidelines could result in reduced machine 2. Unlock the park brake and move the transaxle shift
performance, diminished traction and poor handling. lever to the neutral (N) position for towing.
Inflation 3. Move the four wheel drive control to Disengaged/Off
position.
CAUTION: Explosive separation of tire and rim
parts is possible when they are serviced Machine Tie Down Locations
incorrectly:
• D o no t a ttemp t t o mou nt a tire w itho ut the
pro pe r eq uip men t a nd e x p erie nc e to pe rform
the job.
• D o n o t i n flfla
at e t h e t i r e s a b o v e t h e
rec omme nd ed p re s s u re.
• Do no t weld o r he at a w he el and tire
a s s e m b l y. H e a t c a n c a u s e a n i n c r e a s e i n a i r
pre s s ure res u l ti ng i n a n ex pl os i on . Wel d in g
c a n s t ruc tura lly wea k e n o r de form the wh ee l.
• Do no t s tan d in fron t o r ov er th e tire a s s emb ly
w h e n i n flfla
at i n g . U s e a c l i p - o n c h u c k a n d
ex tension hos e long enough to allow y ou to
stand to one s ide.
IMPORTANT: Over inflation may damage tires and MXAL44187—UN—10APR13

diminish ride quality. Under inflation could Fasten front of machine through tie down points (A) on front of machine
cause wheel damage when riding over rough to trailer with a heavy-duty strap, chain, or cable. Strap must be directed
down and outward from machine.
terrain.
An accurate low pressure gauge is available at your John

Deere dealer.
Tire Chains
IMPORTANT: Tire chains are not approved for use on
this vehicle.
43

Operating
5. Equip the trailer or truck with all the necessary lights
and signs required by local, state, provincial, or
federal laws.
6. Remove or secure optional attachments, if equipped.
Fasten rear of machine through tie down points (B) on rear of machine
to trailer with a heavy-duty strap, chain, or cable. Strap must be directed
down and outward from machine.
Hauling the Machine

NOTE: Space limitations may vary from one truck
manufacturer to another. Short bed trucks do not
have the necessary length requirement to
accommodate the machine.
1. Back machine onto the trailer or truck.

2. Leave transaxle shift lever in forward or reverse gear.
3. Park machine safely. (See Parking Safely in the
SAFETY section.)
4. Fasten machine to trailer or truck with straps, chains,
or cables.
44

Optional Attachments & Kits
Attachments and Kits CAUTION: Before working in an environment
containing hazardous substances, i.e. when
NOTE: All attachments and kits are not shown.
using pesticides, check whether the cab offers
Attachments and kits vary by machine model and
sufficient protection. Refer to the product data
may not be available in all regions. Specifications
sheets of the spraying liquid manufacturer
and design are subject to change without notice.
specifying the category required for the cab.
See your John Deere dealer for availability in your
region.
CAUTION: In case of category 3 and 4 cabs, find
out whether the installed filters have been
checked according to EN 15695-2:2009 and
Cab Classification According to EN15695-1 whether they are suitable for the chemical being
(for Application of Crop Protection used (refer to the manufacturer's information)
Chemicals and Liquid Fertilizer) before working in an environment containing
hazardous substances.
Cab classification according to EN 15695-1 provides
information on the effectiveness of protection against
harmful substances offered by the cab. CAUTION: The cab air filters must be serviced
as specified. See Section “Service
Categories 1 to 4 are used for classification and specified Miscellaneous” and “Service Intervals” in this
on a label inside the cab. Operator's Manual.
CAUTION: Refer to product data sheets and

product identification of the crop protection
chemicals. These contain important information
on how to avoid hazards.
The following requirements must be met to offer best

protection:
1. All seals (on door, windows and roof) in good
condition.
2. Doors, windows and roof closed.
3. Grommets for cables in the cab sealed properly.
Label is installed on cab behind passenger seat belt assembly.
Replace label (A) if missing or damaged. See your John 4. Fan ON.
Deere dealer. 5. Cab air filters in good condition.
A — Category 1 - The cab does not offer any protection
against substances which are harmful to health.
B — Category 2 - The cab offers protection against solid Using Quick Clamps
airborne particles such as dust, but not against aerosols Most optional attachments and kits use quick clamps to
and vapors. attach to the machine.
C — Category 3 - The cab offers protection against dust Using Clamps
and aerosols (liquid airborne substances such as spray),
but not against vapors. 1. Check and adjust the tightness of the clamps after
the first 30 days of use.
D — Category 4 - The cab offers protection against dust,
aerosols and vapors.
45

2. If clamps are loose:
• Hella Lights: Loosen bolt (A) on light and direct light

where needed. Tighten bolt to secure in position.
Replacing Bulbs (Mid-Range Lights)
a. Open clamp arm lever (A). 1. Park the machine safely. (See Parking Safely in
SAFETY.)
b. Increase tension by turning lever (A) one full turn
clockwise. Repeat as needed. 2. Open the hood.
c. Lock clamps. CAUTION: Halogen light bulb contains gas
under pressure. The bulb may shatter if the
3. If clamps are tight: glass is scratched or dropped. Wear eye
a. Open clamp arm lever (A). protection and handle bulb with care when
replacing.
b. Decrease tension by turning lever (A) one full turn
counter-clockwise. Repeat as needed.
IMPORTANT: Do not touch glass portion of new bulb
c. Lock all clamps.
with bare skin. Contact with oils or dirt will
reduce bulb life. Handle bulb by the base or
with a clean cloth or gloves.
Light Kits
Adjusting Lights
• Mid-Range Lights: Loosen locknut (A) on bolt and 3. Lift tabs (A) and remove wire harness connector from
direct light where needed. Tighten locknut to secure in lamp socket.
position. 4. Rotate lamp socket (B) 1/8 turn counterclockwise.
Remove lamp and socket assembly from housing
and discard.
46

2. Carefully remove assembly (C) from housing (D).
3. Disconnect wiring connector (E) from bulb assembly
(F).
4. Remove two hex head screws (G) and retainer (H).
5. Remove bulb assembly from housing and replace.
6. Install new headlight lens assembly, and assemble
components reverse order of removal.
Replacing Bulbs (Hella Halogen Lights)
5. To install new headlight, align lamp socket tabs (C) to

housing slots, and rotate 1/8 turn clockwise to lock in
place.
6. Connect wiring connector to new bulb/socket
assembly.
7. Test headlight function.
Replacing Bulbs (Hella HD Lights)
1. Remove four hex head screws (A) and remove outer

ring (B).
1. Remove four hex head screws (A) and remove outer

ring (B).
2. Carefully remove assembly (C) from housing (D).

3. Press wire clips (E) together and remove bulb
assembly (F).
47

4. Turn valve to blue arrow position to close valve.
Occupant Protective Structure (OPS) Rear

Screen
Adjusting Headrest Position
4. Disconnect halogen bulb (G) from wiring harness

connector (H) and replace.
5. Install new headlight lens assembly, and assemble
components reverse order of removal.
Backup Alarm Headrest shown in center position.
Periodically Check Alarm Function 1. Remove two screws (A) and move each headrest (B)
1. Start machine. to either top (C), center (D) or bottom (E) position. Secure
with two screws.
2. Move transmission shift lever into Reverse gear and
listen for alarm.
3. Contact your John Deere dealer if alarm does not
function properly. Front Receiver Hitch
Using Hitch
Cab Heater
MXAL44201—UN—10APR13 1. Mount front accessories into holes (A) in front

receiver hitch.
1. Turn valve (A) to red arrow position to open for heat. 2. Use rings (B) as needed.
2. Push right side of switch (B) to first position for low
fan speed or second position for high fan speed.
3. Push left side of switch fully down to turn fan off.
48

Cargobox Toolboxes CAUTION: Avoid injury! When raising or
lowering tailgate, latch rods can swing outward
IMPORTANT: Avoid damage! Toolbox lids open to
abruptly towards operator. Stand in center of
the side may be damaged by contact with
tailgate and slowly lower or raise tailgate to
objects when operating the machine. Before
make sure that latch rods do not contact
operating the machine, check to be sure that
operator.
the toolbox lids are closed and the latches are
secure.
Check to be sure toolbox lids which open to the side (A) 3. Lower tailgate until it rests on ends of latch rods (C).
are closed before operating machine.
IMPORTANT: Avoid injury! Lower tailgate completely
Operating the Tailgate to unload cargo box only. Never drive with the
CAUTION: Avoid injury! Riders can fall off and tailgate hanging down. Tailgate can contact
be injured or killed. Do not allow riders in the tires and cause damage.
cargo box or on the tailgate.
4. To engage rod in slot (B) in tailgate raise tailgate,
slowly push tailgate upward. Push inward and
upward on loop (A) of latch rod.
Removing the Tailgate

CAUTION: Avoid injury! Riders can fall off and
be injured or killed. Do not allow riders in the
cargo box or on the tailgate.
1. To unhook rods from slot (B) in tailgate, push in and

down on loop (A) of tailgate latch rods.
2. Pull latch rods out and down.
1. Remove and retain rubber hose sleeves from latch

rod ends (A).
2. To disengage from slots (B) in cargo box sides, raise
tailgate slightly and rotate latch rods.
3. Remove latch rods from sides of tailgate.
4. Support tailgate by hand.
49

5. Remove retaining ring (C) and bushing (D) from each

tailgate rod end.
6. Slide tailgate sideways so tailgate rod end is clear of
the cargo box bracket.
7. Pull the detached end of tailgate away from the
cargo box enough to clear the cargo box bracket.
Allow the tailgate to slide in opposite direction to
complete removal.
8. To install, reverse the steps.
Using a Trailer
Follow all trailer manufacturers instructions for safe
operation.
Follow all instructions in this Operators Manual for
attaching optional equipment and towing loads safely.
50

Replacement Parts
Service Literature
If you would like a copy of the Parts Catalog or Technical
Manual for this machine call:
• U.S. & Canada: 1-800-522-7448.
• All Other Regions: Your John Deere dealer.
Parts
We recommend John Deere quality parts and lubricants,
available at your John Deere dealer.
When you order parts, your John Deere dealer needs the
serial number or product identification number (PIN) for
your machine or attachment. These are the numbers that
you recorded in the Product Identification section of this
manual.
Order Service Parts Online
Visit http://JDParts.deere.com for your Internet
connection to parts ordering and information.
51

Service Intervals
Servicing Your Machine • Clean primary drive clutch.
• Inspect battery. Clean if necessary.
IMPORTANT: Operating in extreme conditions may
require more frequent service intervals: • Inspect alternator belt (825i, optional on 625i).
• Grease front and rear suspension bushings.
• E n gine c omp on en ts may b ec ome d irty or
p lug ge d w he n op era ting in e x tre me he at, • Check toe-in.
d us t o r oth er s e v e re c o nd itions . • Check brake pad wear.
• E n gine oil c an d eg rad e if mac h ine is • Check park brake oil level.
o pe ra ted c on s tan tly at s lo w or lo w en gin e • Check and tighten wheel bolts to correct torque.
s pe ed s or f or fre qu en t s ho rt p erio ds o f time.
• Check/clean spark arrestor if equipped.
Please use the following timetables to perform routine • Check and tighten all hardware.
maintenance on your machine. • Inspect cargo box lanyards.
Park the vehicle safely. See Park Safely in the SAFETY
Section.
Every 400 Hours or 24 Months (whichever
comes first)
Break In • Change engine coolant.
• Test or replace radiator cap. (See your John Deere
After First 8 Hours:
dealer for this service.)
• Change engine oil and filter. • Inspect suspension bushings for play. (See your John
• Check and tighten wheel bolts to correct torque. Deere dealer for this service.)
• Check brake fluid level. • Inspect wheel bearings for play. (See your John Deere
• Check alignment of glass cab doors, if equipped. (See dealer for this service.)
your John Deere dealer for this service.) • Inspect timing belt (825i).
• Inspect timing belt idler/bearing (825i).
• Inspect alternator belt (825i, optional on 625i).
Every 50 Hours or Annually
• Check brake fluid level, lines and connections.
• Lubricate drive line (two locations). Every 800 Hours or 24 Months (whichever
• Check 4WD front differential oil level. comes first)
• Check transaxle oil level. • Change transaxle oil.
• Inspect driveline CV boots for tears or punctures. • Change 4WD front differential oil.
• Inspect park brake for proper function. (See your John • Replace drive belt.
Deere dealer for any adjustments needed.)
• Grease cargo box tailgate strikers.
Every 1000 Hours or 24 Months (whichever
comes first)
Every 100 Hours or Annually (whichever • Flush and refill brake fluid. (See your John Deere
comes first) dealer for this service.)
• Change engine oil and filter. • Inspect shocks and struts for leaks.
Every 200 Hours or Annually (whichever

comes first)
• Change fuel filter.
• Change spark plugs.
• Change air cleaner element.
• Check air cleaner dust unloading valve.
• Clean radiator.
• Check drive belt condition.
• Check driven clutch wear buttons (625i).
52

Service Lubrication
Grease
IMPORTANT: Avoid Damage! Use recommended
John Deere greases to avoid component failure
and premature wear.
The following grease is recommended for service:

• John Deere Multi-Purpose HD Lithium Complex
Grease
• Grease-Gard™ Premium Plus
Not all grease types are compatible; John Deere does

not recommend mixing greases. If using any product
other than the recommended grease in service, purge
any remaining grease from the system prior to
application. If this is not practical, grease twice as often MXAL44205—UN—10APR13
until all old grease is purged from the system. View from under vehicle - on front drive shaft.
Lubricate two grease fittings (A) on drive line with one or
two shots of grease.
Lubricating Drive Line
NOTE: You may need to move machine by hand for shaft
(B) to be rotated to line up grease fitting with hole in
driveshaft cover.
View from right rear side of vehicle - on rear drive shaft.
53

Service Engine
Emissions Service Information Avoid Fumes
A qualified repair shop or person of the owner’s choosing CAUTION: Engine exhaust fumes contain
may maintain, replace, or repair emission control devices carbon monoxide and can cause serious illness
and systems with original or equivalent replacement or death.
parts. However, warranty, recall and all other services
paid for by John Deere must be performed at an • Mo v e th e mac h ine to an o uts id e area b efo re
authorized John Deere service center. ru nn ing th e en gin e.
• Do no t run a n en gin e in an e nc lo s e d are a
Within the warranty period, John Deere will reimburse
without adequate ventilation.
reasonable service costs incurred at service providers
outside the John Deere authorized network only in an • Connect a pipe ex tension to the engine
unsafe, emergency condition if an authorized John e x ha us t p ipe to d irec t th e ex ha us t fu mes o ut
Deere dealer is not available and the failure does not o f th e are a.
arise from the owner’s misuse or failure to perform • A llo w fres h o uts ide a ir in to the wo rk area to
required maintenance. An emergency situation exists clear the exhaust fumes out.
under this section if, after 30 days, the authorized John
Deere network is unable to perform the repairs or source
replacement parts. Engine Oil
Emission Control System Certification Label Use oil viscosity based on the expected air temperature
range during the period between oil changes.
NOTE: Tampering with emission controls and
components by unauthorized personnel may result
in severe fines or penalties. Emission controls and
components can only be adjusted by EPA and/or
CARB authorized service centers. Contact your
John Deere Retailer concerning emission controls
and component questions.
The presence of an emissions label signifies that the

engine has been certified with the United States
Environmental Protection Agency (EPA) and/or
California Air Resources Board (CARB).
The emissions warranty applies only to those engines
marketed by John Deere that have been certified by the The following John Deere oils are preferred:
EPA and/or CARB; and used in the United States and • TURF-GARD™
Canada in off-road mobile equipment.
• PLUS- 4™
Altitude Adjustment (Gasoline Engines Only)
Other oils may be used if above John Deere oils are
If your engine features a carburetor it is calibrated by the not available, provided they meet the following
engine manufacturer and is not adjustable. specification:
If your engine is operated at altitudes below 1006 m • API Service Classification SG or higher
(3,300 ft.), a high altitude carburetor jet kit is not required.
If your engine is operated at altitudes above 1006 m
(3,300 ft.), a high altitude carburetor jet kit may be
required for proper engine performance and emissions Checking Engine Oil Level
control. Operating the engine with the wrong carburetor
IMPORTANT: Failure to check the oil level regularly
configuration at a given altitude may increase the
could lead to serious engine problems if oil
engine’s emissions and decrease fuel efficiency and
level is out of the operating range:
performance.
• C h ec k o il le v el be fore op era ting .
See a qualified service provider for details on jet kit
requirements for your specific product. • Check oil level when the engine is cold and
n ot ru nn ing.
• K ee p oil lev el be twe en th e dip s tic k ma rk s .
• S h u t o ff e n g i n e b e f o r e a d d i n g o i l .
SAFETY section.)
54

Service Engine
2. Raise and secure cargo box. 3. Raise and secure cargo box.
4. Remove three bolts (A) and closeout panel (B) from

machine.
3. Remove dipstick (A) and wipe it clean.

4. Install dipstick.
5. Remove dipstick.
6. Check oil level:
• Oil level must be between fill marks on dipstick.
• If oil level is low, add oil to bring oil level no higher
than upper mark on dipstick.
• If oil level is above upper mark, drain to proper
level. Determine cause of this condition and
correct.
7. Install dipstick. MXAL44209—UN—10APR13
8. Lower the cargo box.
Changing Engine Oil and Filter

IMPORTANT: Change the oil more often if the vehicle
is used in extreme conditions:
• E x tre mely d us t y c on ditio ns .
• Freq ue nt s lo w o r lo w-s pe ed ope ra tion .
• Freq ue nt s h ort trip s .
1. Run engine to warm the oil.
SAFETY section.)
55

Service Engine
Cleaning Dust Unloading Valve

IMPORTANT: Do not operate engine without air
cleaner element and rubber dust unloading
valve installed.

SAFETY section.)
2. Allow engine to cool.
5. Place drain pan under engine drain plug hole (C) and
oil filter drain hole (D) in frame. 3. Squeeze dust unloading valve (A) to clean. Remove
6. Pull off oil fill cap (E) from filler opening. and replace if damaged.
7. Remove drain plug (F) and drain oil into oil drain pan.
Allow oil to drain completely.
Servicing Air Cleaner Element
8. Remove and discard oil filter (G) on front of engine.
Wipe off filter base on engine. IMPORTANT: Dirt and debris can enter engine when
9. Put a light coat of clean engine oil on gasket of new air cleaner canister is opened. Do not open
oil filter. canister unless required for scheduled service.
This will keep contamination of the intake
10. Install new filter until rubber gasket contacts filter system to a minimum.
base. Tighten filter an additional one-half turn.
Check filter element more frequently if
11. Install drain plug. Tighten to specification. operating in dusty conditions.
Specification
Drain Plug — Torque . . . . . . . . . . . . . . . . . . . .40 N·m (29 lb-ft) 1. Park the vehicle safely. (See Parking Safely in the
SAFETY section.)
IMPORTANT: Do not overfill crankcase with oil. Oil
capacities given are with engine and crankcase 2. Allow engine to cool.
completely dry. Some oil will remain in engine
after draining.
12. Add recommended fluid no higher than upper mark

on dipstick (H). Do not overfill.
13. Install oil fill cap.
14. Start and run engine at idle to check for leaks. Stop
engine. Fix any leaks before operating.
15. Check oil level and add oil if necessary.
16. Install closeout panel with three bolts.
56

Service Engine
MXAL44212—UN—10APR13 MXT008471—UN—14SEP13
3. Release latches (A) and remove air cleaner canister 4. Pull up on center retainer (E) and remove entire
cover (B). retainer assembly (C). Remove access cover panel
(D).
4. Remove and discard filter element (C). Replace with

a new filter element.
5. Install air cleaner canister cover with rubber dust
unloading valve pointing downward. Check
instruction molded into canister cover for proper
installation.
6. Hook the canister cover latches.
Checking Air Intake, Hoses and Clamps

1. Park the machine safely. (See Parking Safely in the
SAFETY section.)
2. Tip or remove seat as needed.
3. Raise and secure cargo box.
57

Service Engine
8. Check and adjust spark plug gap (A):

• See SPECIFICATIONS for gap distance.
9. Install and tighten spark plug(s). Tighten to
specification.
MXAL44215—UN—10APR13 Specification
Spark Plug(s) — Torque. . . . . . . . . . . . . . . . . .25 N·m (18 lb-ft)
5. Check intake hoses (A) for damage or cracking.
Replace if necessary. 10. Install spark plug wire(s).
6. Check and tighten air intake hose clamps (B) as 11. Lower the cargo box.
needed.
Replacing Fuel Filter
8. Install under seat cover and secure with retainer.
CAUTION: Fuel vapors are explosive and
9. Tip seat back or install seat. flammable:
• Do not s mok e while handling fuel.
• K e e p f u e l a w a y f r o m flfla am e s o r s p a r k s .
Checking Spark Plug
• S h u t o ff e n g i n e b e f o r e s e r v i c i n g .
CAUTION: Touching hot surfaces can burn skin. • Coo l e ng ine b efo re s e rv ic in g.
The engine, components, and fluids will be hot if
the engine has been running. Allow the engine • Wo r k i n a w e l l - v e n t i l a t e d a r e a .
to cool before servicing or working near the • C l e a n u p s p i l l e d f u e l i m m e d i a t e l y.
engine and components.
Relieve Fuel Line Pressure
SAFETY section.) 1. Park the vehicle safely. (See Parking Safely in the
SAFETY section.)
2. Raise bucket seat, or remove bench seat base.
3. Disconnect spark plug wire(s).
3. Start and run engine.
4. Remove spark plug(s) using appropriate spark plug
socket.
5. Inspect spark plug(s) for:
• Cracked porcelain.
• Pitted or damaged electrodes.
• Other wear or damage.
6. Clean spark plug(s) carefully with a wire brush.
NOTE: In Canada, replace with resistor spark plug only.
7. Replace spark plug(s) if necessary.
58

Service Engine
4. Disconnect wiring connector (A) for fuel pump and

run until engine quits.
Remove Old Filter

CAUTION: Cover connections with a cloth while
disconnecting fuel line to avoid fuel spray from
residual pressure in system. MXAL44389—UN—28MAR13
2. Locate the fuel filter (B) at the right front of the engine
IMPORTANT: Do not pry the plastic clip out from the compartment.
fuel line quick connect end. Push the closed
end of the plastic clip in toward the fuel line. 3. Place a drain pan or cloth under fuel lines to catch
This spreads out the barbs on the clip and the any fuel left in lines.
line can be disconnected. 4. Press on release mechanism to disconnect fuel line
couplers (C) from filter.
5. Remove push fasteners on top (D) and bottom
holding fuel filter to frame.
Install New Filter

IMPORTANT: Incorrect installation of fuel filter may
cause engine damage. Install the filter with the
arrow pointing in the direction of fuel flow
(towards the engine) for proper operation.
1. Install new filter making sure filter arrow (E) is

pointed in the direction of fuel flow (towards the
engine). Secure filter with push fasteners onto frame.
2. Connect fuel line couplers to new filter, making sure
couplers are securely connected.
3. Connect wiring connector for fuel pump.
4. Turn ignition key to the RUN position for several
seconds, and turn key off. Check for leaks.
5. Return or install seat.
59

Service Engine
Cleaning Engine Compartment
CAUTION: Touching hot surfaces can burn skin.
The engine, components, and fluids will be hot if
the engine has been running. Allow the engine
to cool before servicing or working near the
engine and components.

SAFETY section.)
CAUTION: Compressed air can cause debris to
fly a long distance.
• Clea r wo rk area o f b y s t and ers .
• Wea r e y e pro tec ti on w he n u s i ng c omp re s s e d
a ir fo r c lea nin g pu rpo s e s .
• Red uc e c o mpre s s ed a ir p res s u re to
s p e c i fificca t i o n .
Specification
Air — Pressure . . . . . . . . . . . . . . . . . . . . 210 kPa (30 psi)
IMPORTANT: High-pressure water can damage seals,

gaskets, and force water into electrical
connectors. Use water from a hose or pressure
washer with pressures less than 420 kPa (60
psi).
3. Remove any debris in engine compartment, MXT010627—UN—23JUL14

especially around exhaust components.
• Keep engine intake manifold (C) and the top of
4. Remove any other debris:
engine compartment closeout panel (D) clear of
any debris.
• Keep closeout panel holes (A) and slots (B) clear

of any debris.
60

Service Engine
• Keep front and rear of entire muffler and muffler
shield (E) clear of any debris.
3. Remove all dirt and debris from radiator fins (A) and
5. Check and remove any obstructions around the fan shroud (B) using compressed air or water. Flow
control cables and linkages. of compressed air or water should be from back to
front.
4. Close hood.
Cleaning Radiator Cooling Fins
CAUTION: Compressed air can cause debris to
fly a long distance. Checking Coolant Level
• Cle ar w ork are a of by s ta nd ers . 1. Park the vehicle safely. (See Parking Safely in the
SAFETY section.)
• We a r e y e p r o t e c t i o n w h e n u s i n g c o m p r e s s e d
air for c leaning purposes . 2. Allow engine to cool.
• Red uc e c omp res s e d air pres s ure to 3. Open hood.
s p e c i fificca t i o n .
Specification
Air — Pressure . . . . . . . . . . . . . . . . . . . . 210 kPa (30 psi)
IMPORTANT: Cooling fins must be clean to prevent

engine from overheating and to allow adequate
air intake.

SAFETY section.)
2. Open hood.
IMPORTANT: High-pressure water or air can damage
cooling fins or other engine components. Use
water from a hose or reduce compressed air
pressure to 210 kPa (30 psi).Turn engine off
before cleaning radiator screen and fins.
4. Check recovery tank (A) coolant level:

• If engine is warm, coolant level should be between
the FULL line (B) and the LOW line (C).
• If engine is cold, coolant level should be at the
LOW line (C) on the recovery tank.
5. Remove recovery tank cap (D) if necessary to add
coolant.
6. Add coolant mixture to recovery tank.
61

Service Engine
IMPORTANT: Installing suction hose incorrectly will • Tip seats back.
not allow coolant into the coolant system. Do • Lower cargo box.
not allow bottom of hose to touch bottom of
bottle or bend upwards out of coolant. Draining Cooling System
1. Make sure engine has cooled completely.
7. Install and tighten recovery tank cap.
CAUTION: The radiator will be hot and can burn
8. Close hood. skin. Built-up pressure may cause explosive
release of coolant when the radiator cap is
removed:
Service Cooling System Safely • S h u t o ff t h e e n g i n e a n d a l l o w t o c o o l .
• Do no t remo v e th e c a p un le s s th e rad iato r
a nd th e en gine are c oo l en ou gh t o tou c h with
b are h an ds .
• S l o w l y l o o s e n t h e c a p t o t h e fifirrs t s t o p t o
re lea s e all pres s ure . Th en re mov e the c ap .
CAUTION: Avoid injury! The radiator is hot and

burns skin. Built-up pressure causes explosive
release of coolant when the radiator cap is
removed:
• S h u t o ff t h e e n g i n e a n d a l l o w t o c o o l .
• Do no t remo v e th e c a p un les s th e ra diat or MXAL44226—UN—10APR13
a nd th e en gin e are c oo l e no ug h to tou c h with
b are h an ds .
2. Slowly open radiator cap (A) to the first stop to
• S l o w l y l o o s e n t h e c a p t o t h e fifirrs t s t o p t o release all pressure.
re lea s e a ll pres s ure. Th en remo v e the c ap .
3. Remove cap after all pressure is released.
Servicing Cooling System

IMPORTANT: Follow all service procedures exactly. If
not equipped to perform this work, see your
John Deere dealer for service.
Prepare Vehicle
SAFETY section.)
2. Raise cargo box.
3. Tip seats forward.
4. Open hood.
5. Remove storage tray. MXAL44227—UN—10APR13
6. When the coolant system service is completed:

• Install storage tray. 4. Remove three bolts (B) and closeout panel (C) from
machine.
• Close hood.
62

Service Engine
5. Place a coolant drain pan under area where closeout IMPORTANT: Install overflow hose properly to ensure
panel was removed. proper function of the cooling system. Position
hose slightly above bottom of reservoir. Do not
allow hose to contact bottom of reservoir or
bend upwards out of the coolant.
15. Install overflow hose (F) and cap (H).

16. Install closeout panel with three bolts.
17. Fill and bleed cooling system.
Filling and Bleeding Cooling System

IMPORTANT: Using incorrect coolant mixture can
damage the radiator:
• D o no t o pe ra te en gine with ou t c oo lan t o r
w i t h p l a i n w a t e r.
MXAL44228—UN—10APR13 • D o no t e x c eed a 50 % a ntifre ez e mix tu re for
View from under left (driver) side. the coolant.
6. Loosen hose clamps (D), and disconnect radiator • U s e a ntifre ez e a pprov e d fo r us e in alu minu m
hoses (E) from intermediate tubes. engines.
7. Route radiator hoses over the drain pan and allow • D o no t p ou r c oo lan t o r wa ter in to rad iato r
coolant to drain into drain pan. when engine is hot.
• Do not add Stop Leak or other additives.
8. Raise front of vehicle to ensure complete drainage of
coolant. NOTE: John Deere COOL-GARD™ coolant is
9. After all coolant has drained, lower front of vehicle recommended when adding coolant to the cooling
and connect radiator hoses (E). system. Follow the directions on the container for
correct mixture ratio.
10. Remove overflow hose (F) from recovery tank.

11. Remove the screw (G) and lift recovery tank out of MXT010628—UN—23JUL14
machine.
12. Remove cap (H) and empty recovery tank into drain 1. Loosen bleed valve screw (A).
pan. 2. Remove radiator cap and add recommended coolant
13. Check condition of all hoses. Replace as needed. mixture to radiator until coolant runs out of bleed
Check all hose clamps and tighten as needed. port.
14. Install recovery tank in machine and secure with 3. Tighten bleed valve screw.
screw (G).
™COOL-GARD is a trademark of Deere & Company
63

Service Engine
4. Add additional coolant mixture to radiator until CAUTION: The radiator will be hot and can burn
coolant runs out of overflow port and into the skin. Built-up pressure may cause explosive
recovery tank. release of coolant when the radiator cap is
5. Install radiator cap. removed:
IMPORTANT: Position hose slightly above bottom of • S h u t o ff t h e e n g i n e a n d a l l o w t o c o o l .
recovery tank. Do not allow hose to contact • Do no t remo v e th e c a p un le s s th e rad iato r
bottom of recovery tank or bend upwards out of a nd th e en gine are c oo l en ou gh t o tou c h with
the coolant. b are h an ds .
• S l o w l y l o o s e n t h e c a p t o t h e fifirrs t s t o p t o
6. Remove recovery tank cap and add coolant mixture re lea s e all pres s ure . Th en re mov e the c ap .
to recovery tank until it is approximately half full.
6. Turn radiator cap slowly to the stop to release
7. Install recovery tank cap. system pressure. Remove radiator cap.
IMPORTANT: If coolant temperature indicator comes 7. Drain cooling system immediately into a container
on while engine is running, stop engine and before.
add more coolant mixture to radiator. • Disconnect radiator hoses from engine.
8. Start and run engine at medium speed until upper 8. After all solution has drained, connect radiator
and lower radiator hoses have become warm (10 - hoses.
15 minutes), indicating thermostat has opened and 9. Remove and clean recovery tank.
coolant is circulating.
10. Install the recovery tank.
9. Allow engine to cool.
11. Fill cooling system with recommended coolant
10. Loosen bleed valve screw and allow air to bubble out mixture.
until air bubbles are no longer visible at bleed port.
Tighten bleed valve screw completely.
11. Remove radiator cap and add recommended coolant
Recommended Engine Coolant
mixture to radiator until coolant runs out of overflow
port and into the recovery tank. IMPORTANT: Avoid damage! Using incorrect coolant
12. Install radiator cap. mixture overheats and damages the radiator
and engine:
13. Run engine until cooling fan starts, indicating the
• D o n o t o p e r a t e e n g i n e w i t h p l a i n w a t e r.
engine and coolant has reached operating
temperature. • D o n ot ex c ee d a 5 0% mix tu re of c o ola nt an d
w a t e r.
14. Stop engine and remove key.
• A luminum engine blocks and radiators
15. Allow engine to cool and suction back any excess req uire a pp rov ed e thy le ne g ly c ol-b as e d
coolant from overflow recovery tank. Fill recovery c oolant.
tank as needed to lower line.
The engine cooling system is filled to provide year-round
Flushing Cooling System protection against corrosion and cylinder liner pitting.
1. Drain cooling system. Winter freeze protection is to -37 degrees C (-34 degrees
F). If protection at lower temperatures is required, consult
2. Prepare a cooling system flushing solution using your John Deere dealer for recommendations.
clean water and John Deere Cooling System
Cleaner, John Deere Cooling System Quick Flush, or The following coolants are preferred:
an equivalent.
• John Deere Cool-Gard™ II Premix
3. Fill radiator completely with flushing solution. Install • John Deere Cool-Gard™ Premix
and tighten radiator cap.
• John Deere Cool-Gard™ PG Premix
4. Start and run engine until it reaches operating
temperature. John Deere Cool-Gard™ II Premix and John Deere Cool-
Gard™ Premix are available in a concentration of 50%
5. Stop engine. propylene glycol.
™Cool-Gard is a trademark of Deere & Company

64

Service Engine
John Deere Cool-Gard™ PG Premix is available in a NOTE: Visually inspect hoses for cracks and wear.
concentration of 55% propylene glycol. Squeeze hoses to check for deterioration. Hoses
should not be hard and brittle, nor soft or swollen.
Additional recommended coolants:
• John Deere Cool-Gard™ II Concentrate in a 40% to
60% mixture of concentrate with water.
• John Deere Cool-Gard™ Concentrate in a 40% to
60% mixture of concentrate with water.
If the recommended coolants are unavailable, use an

ethylene glycol or propylene glycol base coolant that
meets the following specification:
• ASTM D3306 prediluted (50%) coolant.
• ASTM D3306 coolant concentrates in a 40% to 60%
mixture of concentrate with water.
Check container label before using to be sure that it has
the appropriate specifications for your machine. Use
coolant with conditioner or add conditioner to coolant
before using.
Water Quality
• Water quality is important to the performance of the
cooling system. Distilled, deionized, or demineralized
water is recommended with ethylene glycol base
engine coolant concentrate.
Checking Radiator Hoses and Clamps MXT010629—UN—23JUL14

SAFETY section.)
2. Raise cargo box.
3. Open hood.
4. Remove storage tray.
6. Check radiator hoses (C) between intermediate

tubes and engine for damage or cracking. Replace if
necessary.
7. Check hose clamps (D) and tighten or replace as
needed.
5. Remove three bolts (A) and closeout panel (B) from

machine.
65

Service Engine
8. Check radiator hose (E) between intermediate tubes 4. Remove bolt (C) and slide coupler forward onto
and radiator for damage or cracking. Replace if driveshaft (D).
necessary.
5. Remove two bolts (E) and remove driveshaft.
9. Check hose clamps (F) and tighten or replace as
needed. 6. Loosen bolt (F) and bolt (G).
10. Install storage tray. 7. Rotate alternator (H) and remove belt (I) from
alternator pulley, water pump pulley (J), and
11. Install closeout panel with three bolts. crankshaft pulley (K).
12. Close hood. 8. Remove four bolts and water pump pulley (J).
13. Lower cargo box.
Inspecting Timing Belt

Inspecting Belt
SAFETY section.)
2. Disconnect negative (-) battery cable.
Engine shown removed from machine for better view.
9. Remove bolt (L) and dipstick tube (M).
10. Remove bolt (N) securing crankshaft pulley (K) and
remove pulley. Use a puller if necessary.
3. Remove two bolts (A) and belt cover (B) from
machine.
66

Service Engine
Inspecting Tensioner Pulley
IMPORTANT: Do not rotate belt or engine pulleys
from the current position. There are timing
marks on bottom and top of engine that align
critical internal engine components.
MXAL44238—UN—10APR13 1. Loosen bolt (R) on tensioner pulley (S). Push

tensioner arm (T) inward slightly to release tensioner
11. Remove seven bolts (O) and timing belt cover (P). pulley tension from timing belt. Rotate tensioner
pulley (S) and check for any noise or if it is loose. If it
is loose, tighten bolt on tensioner pulley to
specification.
Specification
Bolt — Torque . . . . . . . . . . . . . . . . . . . . . . . . .25 N·m (18 lb-ft)
2. If tensioner pulley is noisy, remove bolt (R) and

remove tensioner pulley (S).
3. Install tensioner and push tensioner arm in direction
of arrow (U) until the gap between the tensioner
pulley (S) and the bottom of the water pump housing
is approximately 5 mm (0.2 in.) (V) as shown.
4. Tighten tensioner bolt (R) to specification.
Specification
Bolt — Torque . . . . . . . . . . . . . . . . . . . . . . . . .25 N·m (18 lb-ft)
5. Reverse inspecting belt steps to install all

components in reverse order of removal.
6. Connect negative (-) battery cable.
Inspecting Alternator Belt

MXAL44239—UN—10APR13 Inspect Belt
12. Inspect timing belt (Q) for cracks, fraying, wear or SAFETY section.)
damage. If timing belt needs to be replaced, see the
technical manual for your machine or see your John 2. Disconnect negative (-) battery cable.
Deere Dealer.
13. Inspect tensioner pulley before reinstalling
components (see steps below).
67

Service Engine
3. Remove two bolts (A) and belt cover (B) from 2. Loosen bolt (A) and bolt (B).
machine.
3. Rotate alternator (C) and remove belt (D) from
alternator pulley, water pump pulley (E), and
crankshaft pulley (F).
4. Install new belt around all three pulleys. Rotate
alternator (C) to obtain specified deflection and force
at location (H), and tighten bolt (B). Tighten bolt (A).
Specification
Belt — Deflection. . . . . . . . . . . . . . . . . . . . . . 5 mm (13/64 in.)
Belt — Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 N (20 lb)
5. Install belt cover with bolts.
Checking Spark Arrestor

CAUTION: Touching hot surfaces can burn skin.
MXAL44242—UN—10APR13 The engine, components, and fluids will be hot if
the engine has been running. Keep hands and
4. Inspect belt (C) for wear or damage. Replace if worn body away from hot surfaces when servicing or
or damaged. (See “Replace Belt” for procedure.) working near the engine and components.
5. Test belt tension at location (D) (half way between
alternator and engine pulley). Deflection and force 1. Park the vehicle safely. (See Parking Safely in the
should be to specification. SAFETY section.)
Specification 2. Allow vehicle to cool completely.
Belt — Deflection. . . . . . . . . . . . . . . . . . . . . . 5 mm (13/64 in.)
Belt — Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 N (20 lb)
• To adjust belt tension, loosen bolt (E) and bolt (F).
Rotate alternator (G) to obtain the specified
deflection and force at location (D), and tighten
bolt (F). Tighten bolt (E).
Specification
Belt — Deflection. . . . . . . . . . . . . . . . . . . . 5 mm (13/64 in.)
Belt — Force . . . . . . . . . . . . . . . . . . . . . . . . . 89 N (20 lb)
6. Install belt cover with bolts.

7. Connect negative (-) battery cable.
Replace Belt
1. Remove belt cover. MXAL44581—UN—28MAR13
68

Service Engine
3. Loosen nut (A) on clamp securing spark arrestor (B)
on muffler exhaust pipe.
4. Remove spark arrestor, making note of direction of
arrestor inside of exhaust pipe.
5. Make sure deflector screen inside arrestor is not
plugged or damaged:
• If plugged, spray with carburetor/choke cleaner
and blow dry with low pressure compressed air.
• If damaged, replace spark arrestor.
6. Install spark arrestor and tighten nut on clamp to
secure.
69

Service Transmission
Transaxle Oil Checking 4WD Front Differential Oil Level
Use the appropriate oil viscosity based on these air 1. Park machine safely. (See Parking Safely in the
temperature ranges. Operating outside of these SAFETY section.) Allow machine to cool down for at
recommended oil air temperature ranges may cause least one hour.
premature hydrostatic transmission or hydraulic system
IMPORTANT: Dirt and debris in oil may cause
failures.
damage to the 4WD differential. Clean area
IMPORTANT: Mixing of LOW VISCOSITY HY - around opening before removing plug.
GARD™ and HY - GARD™ oils is permitted. DO
NOT mix any other oils in this transmission. DO
NOT use engine oil or “Type F” (Red) Automatic
Transmission Fluid in this transmission.
John Deere J20C HY-GARD™ transmission and

hydraulic oil is recommended. John Deere J20D Low
Viscosity HY-GARD™ transmission and hydraulic oil
may be used, if within the specified temperature range.
Other oils may be used if above recommended John
Deere oils are not available, provided they meet one of
the following specifications:
• John Deere Standard JDM J20C;
• John Deere Standard JDM J20D.
Fill plug under left front side.
2. Remove fill plug (A) located on left side of 4WD front
differential.
3. Oil should be level with the bottom of the fill port. If oil
level is low:
a. Add oil through fill port until level is correct.
b. Install and tighten fill plug to specification.
Specification
Fill Plug — Torque . . . . . . . . . . . . . 11 - 40 N·m (8 - 30 lb-ft)
Changing 4WD Front Differential Oil

4WD Front Differential Oil
NOTE: It may be necessary to remove front skid plate to
Use the appropriate oil viscosity based on these air access drain plug.
temperature ranges. Operating outside of these
recommended oil air temperature ranges may cause 1. Operate machine to warm 4WD front differential oil.
premature hydrostatic transmission or hydraulic system
failures. 2. Park machine safely. (See Parking Safely in the
SAFETY section.)
IMPORTANT: Mixing of LOW VISCOSITY HY -
GARD™ and HY - GARD™ oils is permitted. DO IMPORTANT: Dirt and debris in oil may cause
NOT mix any other oils in this transmission. DO damage to the 4WD differential. Clean area
NOT use engine oil or “Type F” (Red) Automatic around opening before removing plug.
Transmission Fluid in this transmission.
John Deere J20C Low Viscosity HY-GARD™

transmission and hydraulic oil is recommended.
Other oils may be used if above recommended John
Deere oils are not available, provided they meet the
following specifications:
• John Deere Standard JDM J20C.
70

Checking Transaxle Oil Level
IMPORTANT: Hot hydraulic oil will expand and show
incorrect oil level. Check oil level:
• When oil is cold.
• With e ng ine n ot run nin g.
SAFETY section.)
IMPORTANT: Dirt and debris in oil may cause
damage to the transaxle. Clean area around
opening before removing dipstick.
Drain plug under right front side.
Fill plug under left front side. 3. Remove dipstick (A) located on the top of the
3. Position drain pan under 4WD front differential drain transaxle housing. Wipe dipstick clean.
plug (A) at bottom right of housing. 4. Check oil level by setting dipstick on threads in
4. Remove fill plug (B) located on left side of 4WD front transaxle case, then removing and checking oil level.
differential. 5. Add oil as needed through the dipstick fill hole.
5. Remove 4WD front differential drain plug (A) and 6. Install and tighten dipstick.
allow oil to drain through opening (C) in frame and
into drain pan. 7. Lower the cargo box.
6. Check washer on drain plug. Replace if missing or in
poor condition.
7. Install and tighten drain plug to specification after all Changing Transaxle Oil
oil has drained. 1. Park the vehicle safely. (See Parking Safely in the
Specification SAFETY section.)
Drain Plug — Torque . . . . . . . . . . . . . . . . .7-14 N·m (5-10 lb-ft)
8. Add oil until the level is even with the bottom of the fill IMPORTANT: Dirt and debris in oil may cause
port. damage to the transaxle. Clean area around
9. Install and tighten fill plug to specification. opening before removing dipstick.
Specification
Fill Plug — Torque . . . . . . . . . . . . . . . . . . 11-40 N·m (8-30 lb-ft)
10. Check 4WD front differential oil level again after the
first several hours of operation.
71

3. Position drain pan under transaxle drain plug (A).

4. Remove plug and drain oil.
5. Check washer on drain plug. Replace if missing or in
poor condition.
6. Install and tighten drain plug to specification.
Specification
Drain Plug — Torque . . . . . . . . . . 44 - 54 N·m (32.5 - 39.9 lb-ft)
7. Remove dipstick located on top of transaxle housing.

Wipe dipstick clean.
8. Add recommended fluid.
9. Check oil level by setting dipstick on threads in
transaxle case, then removing and checking oil level.
10. Wait for two minutes then check oil level. Add oil if Viewed from under the machine.
necessary.
2. Inspect four rear CV boots (A) for tears or punctures.
11. Install dipstick and tighten.
3. Inspect four front CV boots (B) for tears or punctures.
12. Lower the cargo box. Repeat for opposite side of machine.
4. Inspect rear drive shaft boot (C) for tears or
punctures.
Inspecting Driveline CV Boots 5. If replacement of a boot is necessary, see your John
1. Park the vehicle safely. (See Parking Safely in the Deere dealer.
SAFETY section.)
Servicing Drive Belt

Inspecting Drive Belt
CAUTION: Rotating parts can catch fingers,
loose clothing, or long hair. Wait for engine and
all moving parts to stop before leaving
operator’s station to adjust or service machine.

SAFETY section.)
72

NOTE: Drive belt can be inspected through enclosure
exhaust port (A) with out removing clutch
enclosure cover.
4. Remove ring (A), loosen two clamps (B) and remove

air intake hose (C).
3. Measure the top surface of the belt width at (B).

Replace belt if dimension is less than 29 mm (1.1
in.).
4. Check for debris inside enclosure exhaust port and
clean if needed.
Removing Drive Belt

SAFETY section.)
CAUTION: The machine can fall or slip from an
unsafe lifting device or supports.
• Us e a s a fe lifting d ev ic e ra ted fo r the loa d to 5. Remove left rear shock (D).
be lifted.
• Lo wer mac hin e on to jack s tan ds o r o the r
s ta ble s u pp orts an d bloc k wh ee ls be fore
s e rv ic in g.
3. Lift machine and secure so tires are off the ground
and suspension hangs freely.
6. Remove eleven bolts around (E) clutch enclosure

cover (F). Remove clutch enclosure cover.
73

7. Lift up on drive belt (G) to make slack. 2. Install clutch enclosure cover (B) and eleven bolts
(C).
8. Start drive belt over edge of driven clutch (H) and
turn clockwise until drive belt is removed. 3. Install left rear shock.
9. Spin idler sleeve bearing (I). Confirm bearing rotates

smoothly. If not, contact your John Deere dealer for
possible bearing replacement.
Replacing Drive Belt 4. Install air intake hose (D), retaining ring (E), tighten
two clamps (F).
NOTE: Make sure arrows on drive belt face towards the
front of machine.
Checking Driven Clutch Rollers

SAFETY section.)
NOTE: Clutch rollers can be inspected through enclosure
exhaust port (B) without removing clutch enclosure
covers.
1. Loop belt (A) over drive clutch and around driven

clutch, starting at bottom and slide belt into driven
clutch while turning.
74

3. On machine left side, remove retaining ring (A), and

MXT008468—UN—07SEP13 remove top cover (B) along with rubber seal (C) from
air intake hose (D).
3. Move machine slightly forward or backward so clutch
roller (A) can be seen through the exhaust port (B).
4. Check worn clutch rollers (A):
a. There should not be any excessive wear, play, or
metal-to metal contact.
b. If replacement is necessary, see your John Deere
dealer.
Cleaning Primary Drive Clutch and

Enclosure
IMPORTANT: Never lubricate any part of the primary
drive clutch.
1. Park the vehicle safely. (See Parking Safely in the MXAL44263—UN—10APR13

SAFETY section.)
4. Loosen hose clamps (E) and pull air intake hose (D)
off of outer clutch cover.
5. Clean screen (F) on top of air intake hose.
75

6. Through access hole (G), use compressed air to MXAL44267—UN—10APR13

blow dust and debris out of clutch fan area.
9. Clean inside clutch enclosure cover, clutch
enclosure base (K), and around drive (L) and driven
clutch (M) assemblies.
10. Install cover.
11. Install shock.
12. Install air intake hose.
7. Check exhaust port (H) for debris.
8. If debris is found inside exhaust port (H), remove

shock (I), eleven bolts and outer clutch enclosure
cover (J).
76

Service Steering & Brakes
Brake Fluid Checking Brake Pads
The following heavy duty brake fluid is PREFERRED 1. Park machine safely. (See Parking Safely in the
for all drum and disc brakes: SAFETY section.)
• Brake Fluid - DOT4 CAUTION: Avoid injury! The machine can fall or
slip from an unsafe lifting device or supports.
Other brake fluids may be used if they provide the
following: • Us e a s a fe lifting d ev ic e rat ed fo r th e loa d to
be lifted.
• Conforms to Motor Vehicle Safety Standard No. 116.
• Lo we r mac hine o nto ja ck s tan ds or o the r
• Minimum wet boiling point 155°C (311°F).
s ta ble s u pp ort s a nd b loc k wh ee ls be fore
• Minimum dry boiling point 230°C (446°F) to prevent servicing.
vapor lock.
IMPORTANT: Avoid damage! Place jack stands under
frame, not under transmission or engine, when
raising or supporting machine
Checking Brake Fluid Level
2. Raise machine with a safe lifting device and lower
IMPORTANT: Avoid damage! Avoid contamination of machine onto jack stands or other stable supports.
the brake fluid. Thoroughly clean area around Block wheels remaining on the ground to prevent
the filler cap before removing. Do not open the machine movement
brake fluid reservoir cap unless necessary.
Use extreme care when filling the reservoir.
Fluid spilled on painted surfaces causes
damage.
Use only brake fluid from a sealed container.
1. Park vehicle safely. (See Parking Safely in the

SAFETY section.)
2. Open hood.
NOTE: Do not overfill reservoir. Overfilling causes
leakage.
If present, remove cap before removing wheel.
3. Remove the wheel bolts (A).
4. Remove the wheel assembly.
3. Visually check brake fluid reservoir. Brake fluid level

must be between “MIN” (A) and “MAX” (B) marks. If
fluid is low:
• Carefully clean area around reservoir cap (C).
• Remove reservoir cap and add fluid to the “MAX”
mark.
4. Install reservoir cap. MXT011035—UN—08SEP14
5. Close hood.
77

5. Inspect brake pads friction material (B) for wear or Checking Brake Lines
damage. Check each pads friction material 1. Park machine safely. (See Parking Safely in the
thickness. Material must not be less than minimum SAFETY section.)
specification. If below specification or brake pad
friction material is damaged, see your John Deere 2. Protect any painted surfaces from expelled brake
dealer for replacement service. fluid and wipe any areas of excess brake fluid.
Specification
3. Open hood.
Pad Friction Material — Thickness . . . . . . . . . . 1 mm (3/64 in.)
6. Install wheel assembly with valve stem to the

outside.
7. Tighten wheel bolts evenly in alternating sequence
until snug.
8. Repeat procedure for remaining three wheels.
9. Lower machine to the ground.
10. Tighten wheel bolts to:
• Standard wheel assembly: 108 N·m (80 lb.-ft.)
• Sport wheel assembly: 142 N·m (105 lb.-ft.)
Checking Park Brake Fluid MXT011028—UN—04SEP14

1. Park Machine safely on a level surface. (See “Park
Machine Safely” in the SAFETY section.) 4. Check brake line fittings (A) at bottom of reservoir (B)
2. Raise and secure cargo box. for leaks.
5. Tighten brake line fitting banjo bolts, as needed, to
specification.
Specification
Banjo Bolts — Torque . . . . . . . . . . . . . . . . . .27 N·m (20 lb.-ft.)
6. Rotate wheels to provide access to brake calipers.

NOTE: Each caliper has two bleeder screws. If bleeding
brakes is necessary, use only the upper screw (F)
to bleed brake calipers.
View from right rear side of vehicle.
3. Remove hex socket plug (A) to check lubricant level
in park brake housing. Fluid level should be at
bottom of plug opening.
4. If not at proper level, loosen clamp (B) and remove Picture Note: Front shown.
hose (C) from fitting (D). Remove fitting (D). Add
recommended fluid until at bottom of plug (A)
opening. Install plug (A).
5. Install fitting (D), and hose (C) with clamp (B).
78

Picture Note: Rear shown.
7. Inspect lower brake line fitting (C) on each brake
caliper (D) for leaks. Tighten brake line fitting banjo
bolt (E), as needed, to specification.
Specification
Banjo Bolt — Torque . . . . . . . . . . . . . . . . . . .27 N·m (20 lb.-ft.)
8. Lower hood.
9. Start vehicle and press brake pedal. If leaks are still
found, see your John Deere Dealer for service.
Adjusting Park Brake

For proper adjustment of the park brake system, see
your John Deere Dealer.
79

Service Electrical
Electrical • Keep small vent holes open.
WARNING: Battery posts, terminals and related IMPORTANT: This battery comes fully charged. If the
accessories contain lead and lead components, machine is not used by the service expiration
chemicals known to the State of California to cause date indicated on the battery, charge the
cancer and reproductive harm. Wash hands after battery.
handling.
• Recharge, if necessary, at 6-10 amperes for 1 hour.
Service the Battery Safely

Removing and Installing Battery
Removing
SAFETY section.)
CAUTION: Avoid injury! Battery electrolyte

contains sulfuric acid. It is poisonous and can
cause serious burns:
• Wea r e y e p rote c ti o n an d gl o v es .
• K ee p s k in p ro tec ted .
• If ele c tro ly te is s wa llo w ed , g et med ic a l MXAL44446—UN—28MAR13
a t t e n t i o n i m m e d i a t e l y.
• I f e l e c t r o l y t e i s s p l a s h e d i n t o e y e s , flflu
us h 2. Tip seat and cargo rack back to access the battery
imme dia tely wit h w a ter for 1 5-3 0 minu tes an d access cover (A).
get medical attention.
• I f e l e c t r o l y t e i s s p l a s h e d o n t o s k i n , flflu
us h
imme dia tely with wate r a nd g et me dica l
a t t e n t i o n i f n e c e s s a r y.
The battery produces a flammable and
explosive gas. The battery may explode:
• D o n o t s m o k e n e a r b a t t e r y.
• Wea r e y e p rote c ti o n an d gl o v es .
• Do no t allow dire c t meta l c on tac t a c ro s s
b atte ry po s ts .
• R e m o v e n e g a t i v e c a b l e fifirrs t w h e n
disconnec ting.
• Install negative c able last when connecting.
Checking the Battery (Sealed Batteries)
3. Pull up on center retainer (B) and remove entire
NOTE: Do not attempt to open, add fluid or service
retainer assembly (C). Remove access cover (A).
battery. Any attempt to do so will void warranty.
• Keep battery and terminals clean.

• Keep battery bolts tight.
80

Service Electrical
4. Rinse the battery with plain water and dry.
5. Clean terminals and battery cable ends with wire
brush until bright.
6. Install battery.
7. Attach cables to battery terminals, beginning with the
positive cable, using washers and nuts.
8. Apply spray lubricant to terminal to prevent
corrosion.
Using Booster Battery

CAUTION: Avoid injury! The battery produces a
flammable and explosive gas.
To prevent the battery from exploding:
• D o n o t s m o k e o r h a v e o p e n flfla am e n e a r
4. Disconnect all black negative cables (D) from battery b a t t e r y.
first. • We a r e y e p r o t e c t i o n a n d g l o v e s .
5. Slide back rubber protective cover (E) and • D o n o t j u m p - s t a r t o r c h a r g e a f r o z e n b a t t e r y.
disconnect all red positive cables. Wa r m b a t t e r y t o s p e c i fificca t i o n .
Specification
6. Loosen hardware (F) that secures battery hold-down Battery — Temperature . . . . . . . . . . . . . . . . . .16°C (60°F)
(G) and pivot hold-down away from battery. • Do no t c o nn ec t th e n eg ativ e (-) bo os te r c a ble
7. Lift battery from vehicle. to the ne ga tiv e (-) termina l of the d is c h arg ed
b a t t e r y. C o n n e c t a t a g o o d g r o u n d l o c a t i o n
Installing a w a y f r o m t h e d i s c h a r g e d b a t t e r y.
1. Install battery into vehicle with negative (-) terminal
positioned toward front of vehicle and the battery
seated properly in the battery tray.
2. Pivot battery hold-down firmly against battery and
tighten retaining hardware to secure.
3. Connect all red positive cables to positive (+) battery
terminal first. Tighten the connections.
4. Connect all black negative cables to negative (-)
battery terminal. Tighten the connections.
5. Apply general purpose grease or silicone spray to
battery terminals to help prevent corrosion.
6. Slide protective cover down the battery positive
cable and seat it over the positive (+) terminal.
A — Booster Battery
7. Install battery access cover and secure with retainer. B — Disabled Vehicle Battery
C — Positive (+) Post
8. Tip cargo rack and seat down.
D — Positive (+) Post
E — Negative (-) Post
F — Negative (-) Booster Cable End
Cleaning Battery and Terminals
1. Connect positive (+) booster cable to booster battery
(A) positive (+) post (C).
SAFETY section.)
2. Connect the other end of positive (+) booster cable to
2. Disconnect and remove battery.
the disabled vehicle battery (B) positive (+) post (D).
3. Wash battery with solution of four tablespoons of
3. Connect negative (–) booster cable to booster
baking soda to one gallon of water. Be careful not to
battery negative (–) post (E).
get the soda solution into the cells.
81

Service Electrical
IMPORTANT: Avoid damage! Electric charges from 3. Rotate bulb socket (A) 1/8 of a turn counterclockwise
the booster battery damages machine and remove socket from housing.
components. Do not install negative booster
cable to machine frame. Install only to the
engine block.
Install negative booster cable away from
moving parts in the engine compartment, such
as belts and fan blades.
4. Connect the other end (F) of negative (–) booster

cable to a metal part of the disabled machine engine
block away from battery.
5. Start the engine of the disabled machine and run
machine for several minutes.
6. Carefully disconnect the booster cables in the exact
reverse order: negative cable first and then the
positive cable.
Replacing Headlight Bulbs

1. Park the vehicle safely. (See Parking Safely in the MXT008460—UN—01SEP13
SAFETY section.)
4. Pull outward on tabs (B), and disconnect wire
2. Locate headlight housing under the front fender.
connector (C) from socket (D). Discard the
CAUTION: Halogen light bulb contains gas bulb/socket assembly.
under pressure. The bulb may shatter if the
glass is scratched or dropped. Wear eye 5. Connect wiring connector to new bulb/socket
protection and handle bulb with care when assembly. Install the assembly into housing and
replacing. rotate 1/8 turn to lock in place.
6. Test head lamp function.
IMPORTANT: Do not touch glass portion of new bulb
with bare skin. Contact with oils or dirt will
reduce bulb life. Handle bulb by the base or Checking and Replacing Fuses
with a clean cloth or gloves.
IMPORTANT: The electrical system may be damaged
if incorrect replacement fuses are used.
Replace the bad fuse with a fuse of the same
amp rating.
Fuses Under the Hood

SAFETY section.)
2. Raise hood and remove storage tray.
82

Service Electrical
Circuit Fuse Size Part #
(9) Key Switch 20 amp 57M7691
(10)ECU 3 amp 57M8743
(11) Headlights 10 amp 57M7689
9. Check visually for broken filament in fuse.

10. Push new fuse of correct amp rating into proper
position in fuse block.
11. Install storage tray and lower hood.
Rear Power Port Fuse Under the Seat

SAFETY section.)
2. Raise seat.
3. Fuse identification:
Position Circuit Fuse Size

1 Fan (orange wire) 30 amp
2 Accessory 40 amp
3 Accessory 40 amp
4. Pull fuse from fuses installed onto frame area, as

shown.
5. Look for broken filament in fuse (See Checking Fuse
Filaments in SERVICE MISCELLANEOUS).
6. Push new fuse of correct amp rating into proper
position in fuse block.
7. Remove fuse relay block cover (A) to gain access to
relay block (B).
3. Remove fuse (A).

4. Look for broken filament in fuse (See Checking Fuse
Filaments in SERVICE MISCELLANEOUS).
MXAL44280—UN—10APR13 5. Push new fuse of correct amp rating into proper
position in fuse holder:
8. Fuse identification on relay block (B):
(12) Rear Power Port 15 amp 99M7065
Circuit Fuse Size Part #
(1) Fuel Pump Relay N/A N/A
(2) Start Relay N/A N/A 6. Lower seat.
(3) Fan Relay N/A N/A
(4) Fuel Pump 10 amp 57M7689
(5) Front Dash Power Port 10 amp 57M7689
(6) Center Power Port 5 amp 57M7688
(7) Instrument Cluster 5 amp 57M7688
(8) Start Relay 20 amp 57M7691
83

Service Miscellaneous
Using Proper Fuel and Stabilizer Filling Fuel Tank
IMPORTANT: Avoid damage! Using stale, CAUTION: Avoid injury! Fuel vapors are
contaminated, or improper fuel can result in explosive and flammable:
engine and fuel system damage. Repairs • S h u t e n g i n e o ff b e f o r e fifilll i n g f u e l t a n k .
caused by stale, contaminated, or improper
• A llo w e ng ine to c oo l b efo re re fue lin g.
fuel are not covered by warranty.
• Do not s mok e while handling fuel.
• K e e p f u e l a w a y f r o m flfla am e s o r s p a r k s .
Use regular grade unleaded fuel with an octane rating of
87 octane or higher. Fuel blends containing up to 10% • Fill fu el t an k o utd oo rs or in v en tila ted a re a.
ethanol or up to 15% MTBE reformulated fuel are • C l e a n u p s p i l l e d f u e l i m m e d i a t e l y.
acceptable. Do not use fuel or additives containing • To p r e v e n t s t a t i c e l e c t r i c d i s c h a r g e , u s e
methanol as engine damage can occur. c l e a n a p p r o v e d n o n - m e t a l c o n t a i n e r.
Always use fresh, clean fuel that is purchased in a
quantity that can be used within approximately 30 days. IMPORTANT: Avoid damage! Dirt and water in fuel
Fuel stabilizer should always be added to the fuel each causes engine damage:
time fuel is purchased. Add stabilizer before filling the • Cle an d irt a nd d eb ris fro m th e fue l ta nk
fuel container to insure proper mixing. Such practice opening.
helps prevent engine performance problems and allows
fuel storage in the machine all year without draining. • Us e c lea n, fre s h, s ta biliz e d fu el.
• To k e e p c o n d e n s a t i o n o u t o f t h e f u e l t a n k , fifilll
Store fuel in plastic containers to reduce condensation. the fuel tank at the end of eac h days
Make sure that the cap on the fuel container is tight to o pe ra tio n.
reduce fuel contamination and evaporation. For best fuel
storage life, use a self-sealing gas can. • Us e a no n-me tallic fun ne l w ith a p las t ic
m e s h s t r a i n e r w h e n fifilll i n g t h e f u e l t a n k o r
Fuel is blended to give best seasonal performance. To c o n t a i n e r.
avoid engine performance problems such as hard
starting or vapor lock, use in-season fuel. Use fuel during To prevent condensation and freezing during cold
warm weather that was purchased during that season, weather, fill fuel tank at the end of each days operation.
and use fuel during cold weather that was purchased
during that season. 1. Park machine safely. (See Parking Safely in the
SAFETY section.)
Fuel can become stale in machines with engines that are
used seasonally or infrequently during a season. Stale 2. Allow engine to cool.
fuel can produce varnish and plug carburetor or EFI 3. Remove any trash from area around fuel tank cap.
components which can affect engine performance.
4. Remove fuel tank cap slowly to allow any pressure
Keep fuel storage container tightly covered and in a cool built up in tank to escape.
area out of direct sunlight. Fuel can break down and
degrade if not sealed properly or exposed to sun and 5. Fill fuel tank only to bottom of filler neck. Do not
heat. overfill.
Condensation may collect in the fuel tank because of a 6. Install fuel tank cap.
variety of operating or environmental conditions and, • Gas models: Turn cap until clicks.
over time, may affect your machine’s operation. Fill
machine fuel tank at the end of the day.
Removing and Installing Wheel Assembly
Removing
SAFETY section.)
84

CAUTION: The machine can fall or slip from an 5. If new bolts or wheels are used, tighten wheel bolts
unsafe lifting device or supports. again after 8 hours of vehicle use.
• Us e a s a fe lifting d ev ic e ra ted fo r the loa d to
be lifted.
• Lo wer mac hin e on to jack s tan ds o r o the r Removing and Installing Seats
s ta ble s u pp orts an d bloc k wh ee ls be fore Removing and Installing Front Bench Seat
s e rv ic in g.
IMPORTANT: Place jack stands under frame, not

under transmission or engine, when raising or
supporting machine.
2. Raise machine with a safe lifting device and lower

machine onto jack stands or other stable supports.
Block wheels remaining on the ground to prevent
machine movement.
1. Pull up on front of seat (A) and remove seat from

both studs (B) on seat frame.
2. Pull seat forward to remove both seat ears (C) from
slots (D) on machine cowling.
MXAL44281—UN—10APR13 3. To install seat, install ears (C) into slots (D) on both
Wheel may or may not have a cap to remove when removing the wheel. sides of machine cowling. Push down on front of seat
3. Remove the wheel bolts (A). to secure seat onto studs (B).
4. Remove the wheel assembly. Removing and Installing Rear Bench Seat
CAUTION: Explosive separation of tire and rim
parts is possible when they are serviced
incorrectly:
• D o no t a ttemp t t o mou nt a tire w itho ut the
pro pe r eq uip men t a nd e x p erie nc e to pe rform
the job.
5. Take wheel assembly to an authorized service dealer
for repairs.
Installing
1. Install wheel assembly with valve stem to the
outside.
2. Tighten wheel bolts evenly in alternating sequence
until snug.
3. Lower machine completely to the ground.
4. Tighten wheel bolts to: MXAL44456—UN—28MAR13
• Standard wheel assembly - 108 N·m (80 lb-ft)
• Sport wheel assembly - 142 N·m (105 lb-ft)
85

1. Remove two bolts (A) on seat pivot bracket (B).
Remove seat pivot bracket from seat mounting rod
(C).
2. Repeat on opposite side.
3. Remove seat (D).
4. To install seat, install seat pivot bracket (B) on each
side of seat mounting rod (C) and set on seat
mounting surface. Install two bolts (A) onto each seat
pivot mounting bracket (B) to secure seat position.
Removing and Installing Bucket Seat
1. Tip seat forward.
5. Position seat bracket (C) onto support rail so hinges
(D) fit around rubber bushing tabs.
2. Hold onto seat and remove all screws (A).

3. Remove seat and seat bracket from support rail. Rear position shown
6. Rotate seat bracket upward. Position bottom of seat
against bracket and align correct holes with holes in
seat.
7. Slide seat to the forward (E) or rearward (F) position.
8. Install original screws (A) to secure seat.
9. Tighten seat bracket hardware to specification:
Specification
Seat Bracket Hardware — Torque. . . . . . . . . 10 N·m (7.4 lb.-ft.)
Lifting Machine
SAFETY section.)
4. To install seat, position seat bushings (B) on support
rail so tabs face toward rear of vehicle. CAUTION: The machine can fall or slip from an
unsafe lifting device or supports.
• Us e a s afe liftin g de v ic e ra ted f or the lo ad to
be lifted.
• L ower ma chin e on to jac k stan ds o r oth er
s ta ble s up po rts an d blo c k whe els be fore
s e rv ic ing .
IMPORTANT: Be certain to include bolt heads (A) and

embossed area (B) inside jack cup to prevent
slipping.
86

NOTE: Remove all attachments prior to lifting machine. 5. Safely lift front of machine at machine frame point (E)
or locations (F). Place jack stands or other stable
supports under two machine frame locations (F)
6. If only lifting front of machine, block rear wheels
remaining on ground to avoid movement of machine.
7. To lower machine, lift front and/or rear of machine,
and remove jack stands or supports. Lower machine.
Opening and Closing Hood

Opening Hood

SAFETY section.)
Your machine model may not be shown, but jack locations are as
shown.
2. Safety lift rear of machine frame point (C).
3. Place jack stands or other stable supports under
three frame locations (D).
4. If only lifting rear of machine, block front wheels
remaining on ground to avoid movement of machine.
2. Stand in front of machine and grasp hood lift handle.

3. Pull up on hood release handle (A) to unlock latch.
4. When the hood latch is released, pull upward on the
hood to pivot to full open position.
Closing Hood
1. Grasp hood lift handle.
2. Pivot hood downward to closed position.
3. Press down on hood to latch hood in closed position.
Removing and Installing Storage Tray

Removing
MXAL44288—UN—10APR13 SAFETY section.)
Your machine model may not be shown, but jack locations are as
shown. 2. Open hood.
3. Remove all contents from storage tray.
87

Inspecting Seat Belt
4. Grasp outer edges of the storage tray (A).

5. Flex storage tray to fit past dash panel (B) while
lifting the storage tray out of machine.
Installing
1. Position storage tray over frame.
IMPORTANT: Do not bleach or re-dye webbing.

Webbing could become severely weakened by
this process. Do not use a pressure washer or
other automatic washing machine to clean belt
or connectors.
• Hand wash webbing (A) with warm water and mild

soap. Rinse thoroughly and air dry.
• Inspect outer seat belt connector (B) and inner
MXAL44291—UN—10APR13 connector (C) for damage or wear. If assembly does
not operate properly or if the webbing is torn or frayed,
2. Flex storage tray (A) to fit under dash panel (B) while the seat belt must be replaced.
lowering storage tray into position.
3. Check alignment of cables and harnesses with
routing notches (C). Inspecting Nets or Doors
• Keep nets, doors, and supporting components clean.
4. Secure all items to prevent damage from movement
while operating the machine. • If needed hand wash with garden hose and mild soap.
• Latch and unlatch metal tab of net from buckle during
5. Close hood.
washing for better cleaning. Allow to dry before use.
• Extended machine operation under harsh conditions
may require more frequent inspection and cleaning.
88

Cleaning and Repairing Cargo Box Replacing Cargo Box Tailgate Bushings
Repairing Accessory Tubes
1. Remove the cargo box tailgate (See Removing the

Tailgate in OPERATING).
MXAL44293—UN—10APR13 2. Remove snapfit bushing (A) from both sides of cargo
Use 3M™ Scotchbrite™ pad to polish and smooth nicks, box.
scrapes or scratches in the vinyl surface of the tubes (A).
3. Replace bushings and reinstall the tailgate.
Cargo Box Floor
A rejuvenating product is available for cargo boxes with
the optional spray-in liner. See your John Deere dealer. Checking and Adjusting Toe-In
In order to accurately set front wheel toe-in, suspension
and steering components must be in good condition. All
Checking Fuse Filaments fasteners must be tightened to specification.
1. Remove fuse. 1. Park machine safely. (See Parking Safely in the
SAFETY section.)
2. Turn steering wheel so that front tires are in straight-
ahead position.
3. Check tire pressure. Adjust to specification if needed
(see SPECIFICATIONS).
2. Check visually for broken filament:

• For clear housing fuses, check filament (A).
• For all other fuses, check filament (B) in top of
fuse housing.
4. Measure front wheel hub center height (A) from

surface.
5. Mark tread centerline (B) and hub center height at
front and back of both front tires.
89

f. Check that front tires do not contact suspension
when turned fully left or right.
Adjusting Suspension (Standard Shocks)

Preload Adjustment
When to Adjust:
• Front preload adjustment - increase preload if
operating with front attachment or under heavy load
condition.
MXAL44297—UN—10APR13 • Rear preload adjustment - increase preload if
operating under heavy load condition.
6. Measure distance (C) between tread centerlines at
rear of tires at hub height. How to Adjust:
7. Measure distance (D) between tread centerlines at 1. Park machine safely (see Parking Safely in the
front of tires at hub height. SAFETY Section).
8. Subtract front measurement from rear measurement 2. Block tire not intended to be lifted off the ground.
to determine toe-in. 3. Raise the machine with a safe lifting device and
9. Adjust toe-in if not within specification: lower machine onto jack stands or other stable
Specification
support.
Tire Centerline — Distance. . . . . . . . . . .4±3 mm (0.16±0.12 in.)
NOTE: The steering rack rubber boot may turn with the
tie rod if the tie rod boot clamp is too tight. If this
happens, loosen the boot clamp enough to allow
the rubber boot to remain stationary when the tie
rod is turned.
4. Using the supplied spanner wrench, securely

engage the adjustable preload collar (A) on shock.
Rotate preload collar to desired preload condition
making sure to engage detent feature (B) between
shock and preload collar.
MXAL44298—UN—10APR13 CAUTION: Be sure both front shock preload
Left side shown. collars are set to the same position. Be sure
a. Loosen M12 jam nuts (E) on left and right tie rod. both rear shock preload collars are set to the
same position.
b. Rotate tie rod by placing wrench on hex (F).
c. Loosen boot clamps (G) if necessary to prevent 5. Repeat this operation on all shocks as needed.
boot rotation with tie rod adjustment.
d. Adjust left and right tie rods equally until toe-in is
within specification. Adjusting Suspension (High Performance
e. Tighten jam nuts to specification.
Shocks)
Specification Preload Adjustment
Jam Nuts — Torque. . . . . . . . . . . . . . . . . .95 N·m (70 lb-ft)
When to Adjust:
90

• Front preload adjustment - increase preload if provides a softer ride. Compression adjuster is a
operating with front attachment or cab or under heavy detent (clicks) adjustment. Count the number of clicks
load condition. from one extreme of the adjustment range when
making adjustments to know your position in the
How to Adjust: adjustable range.
1. Park machine safely (see Parking Safely in the • Rear compression adjustment - Adjust the rear
SAFETY Section). compression adjustment to achieve optimum ride
comfort for operating condition or for heavy load
2. Block rear tires. compensation. Clockwise rotation provides a stiffer
3. Raise the front of machine with a safe lifting device ride. Counter clockwise rotation provides a softer ride.
and lower machine onto jack stands or other stable Compression adjuster is a detent (clicks) adjustment.
support. Count the clicks from one extreme of the adjustment
range when making adjustments to know your position
in the adjustable range.
How to Adjust:
1. Park machine safely (see Parking Safely in the
SAFETY Section).
4. Using a punch and hammer, loosen the upper jam

nut (A) tightened against preload collar (B).
5. Using the supplied spanner wrench for high
performance shocks, securely engage the adjustable
2. The compression adjuster is a blue colored knob (A)
preload collar (B) on shock (C). Rotate preload collar
located on the remote reservoir (B) (attached to the
to desired preload condition. The collar will stop
shock by a steel braided hose).
rotating when maximum preload is achieved.
3. Grasp the blue knob and rotate to desired position.
6. Using a punch and hammer, tighten the upper jam
nut against preload collar. CAUTION: Be sure both compression adjustors
are set to the same position.
CAUTION: Be sure both front shock preload
collars are set to the same position. Be sure
4. Repeat this operation on all shocks as needed.
both rear shock preload collars are set to the
same position.
7. Repeat this operation on all shocks as needed. Cleaning Vehicle Surfaces

Compression Adjustment Cleaning:
When to Adjust: Keeping your vehicle clean will maintain its appearance
and can also extend the life of various components.
• Front compression adjustment - Adjust the front Immediately after your vehicle has been exposed to salt
compression adjustment to achieve optimum ride water or operated on muddy trails, rough terrain, or in
comfort for operating condition. Clockwise rotation dusty conditions, wash your vehicle. With some
provides a stiffer ride. Counter clockwise rotation
91

precautions, your vehicle can be cleaned much like a 6. Buff applied wax by hand using a clean, soft cloth.
sport utility vehicle.
IMPORTANT: Improper care of machine plastic
surfaces can damage that surface: Cleaning and Repairing Metal Surfaces
• D o n ot w ipe p las tic s urfa c e s w h en th ey a re Cleaning:
d r y. D r y w i p i n g w i l l r e s u l t i n m i n o r s u r f a c e
s c ra tc h es . Follow automotive practices to care for your vehicle
painted metal surfaces. Use a high-quality automotive
• U s e a s o f t , c l e a n c l o t h ( b a t h t o w e l , d i a p e r, wax regularly to maintain the factory look of your
a ut omo tiv e mitt). vehicle’s painted surfaces.
• D o n ot us e ab ras iv e ma teria ls , s uc h as
p olis hing c omp ou nd s , on p las tic s urfa c e s . Repairing Minor Scratches (surface scratch):
Washing Vehicle: 1. Clean area to be repaired thoroughly.
The recommended and safest way to clean your vehicle IMPORTANT: Avoid damage! Do not use rubbing
is with a garden hose and a pail of mild, soapy water. Use compound on painted surfaces.
a professional type wash mitten. Clean the upper body
first and the lower parts last. Rinse frequently with water 2. Use automotive polishing compound to remove
and dry with a chamois to prevent water spotting. surface scratches.
1. Rinse hood and entire machine with clean water to 3. Apply wax to entire surface.
remove dirt and dust that may scratch the surface.
Repairing Deep Scratches (bare metal or primer
IMPORTANT: High pressure may damage vehicle showing):
components. It is recommended that your
1. Clean area to be repaired with rubbing alcohol or
vehicle be washed by hand or with a garden
mineral spirits.
hose using mild soap.
2. Use paint stick with factory-matched colors available
Avoid spraying water with any great force near
from your authorized dealer to fill scratches. Follow
or into the following places:
directions included on paint stick for use and for
• C lu tc h e nc lo s u re air o utlet drying.
• Air intake 3. Smooth out surface using an automotive polishing
• E lec tric a l c on ne c tion s (inc lud in g ba tte ry compound. Do not use power buffer.
c omp artmen t)
4. Apply wax to surface.
• CV boots
• Whe el be arin gs
• Master cylinder
Cleaning Plastic Hood and Body Panel
• P illow blo c k be arin gs
Surfaces
• Radiator
• Wa r n i n g l a b e l s IMPORTANT: Improper care of machine plastic
surfaces can damage that surface:
• Decals
• D o n ot w ip e pla s tic s u rfa c es w h en th ey a re
• Ignition switch
d r y. D r y w i p i n g w i l l r e s u l t i n m i n o r s u r f a c e
• I ns trume nt pa ne l (g au ge s an d s witc h es ) s c ra tc h es .
• B re ath er/tub e v en ts • U s e a s o f t , c l e a n c l o t h ( b a t h t o w e l , d i a p e r,
2. Wash surface with clean water and a mild liquid a uto motiv e mitt).
automotive washing soap. • D o n ot us e ab ras iv e mat eria ls , s uc h as
p olis h ing c omp ou nd s , on p las tic s urfa c e s .
3. Immediately after washing, lubricate all grease
fittings with grease. 1. Rinse with clean water to remove dirt and dust.
4. Dry thoroughly to avoid water spots. 2. Dry thoroughly to avoid water spots.
5. Wax the surface with a liquid automotive wax. Use 3. Spray PLEDGE® onto hood and surfaces and leave
products that specifically say “contains no on for 30 to 60 seconds.
abrasives.”
4. Wipe off with cheesecloth to bring out lustre.
IMPORTANT: Do not use a power buffer to remove
wax.
92

Windshield Maintenance Polishing or Waxing Windshield
Inspecting Windshield Minimize scratches and minor abrasions with a mild
automobile polish.
CAUTION: Avoid injury! If cracks or surface
crazing are observed, or viewing through Test effectiveness of polish or wax in a small corner of
windshield is impaired, replace windshield. windshield before using on entire windshield.
1. Inspect windshield condition.

2. Fill in existing scratches.
3. Polish or wax windows regularly.
Cleaning Windshield
IMPORTANT: Avoid damage! Some cleaning

compounds may attack the polycarbonate
material, resulting in cracks that weaken the
material.
Never use compounds that contain substances
such as ammonia, gasoline, lacquer thinner,
and turpentine.
Use of abrasive cleaners on windshield may
cause damage.
Never use substances such as acetic acid,
acetone, benzene, benzyl alcohol, brake fluid,
butyric acid, carbon tetrachloride, ethyl ether,
methyl alcohol, phenol, sodium sulfide, sodium
hydroxide, sodium nitrate, trichloroethylene,
toluene, xylene, or petroleum products.
NOTE: The windshield and windscreen are a

polycarbonate material which is softer, but stronger
than, glass.
The following cleaning agents are compatible with

polycarbonate when used according to the
manufacturer’s recommendations: Formula 409®
(without ammonia), Joy®, Ultra Palmolive® Original, Top
Job®, Mr. Clean®, and Fantastik®.
1. Rinse as much loose dirt off as possible with warm
water and a soft cloth or sponge before washing.
2. Wash with mild soap or detergent and rinse
thoroughly with clean water.
3. Cleaning in direct sunlight causes streaking on
surface.
4. Thoroughly dry windshield with a chamois or moist
sponge to prevent water spots.
®Formula 409 is a trademark of The Clorox Company

®Joy is a trademark of Procter & Gamble
®Palmolive is a trademark of The Colgate-Palmolive Company
®Top Job is a trademark of KIK Custom Products
®Mr. Clean is a trademark of Procter & Gamble
®Fantastik is a trademark of SC Johnson
93

Troubleshooting
Using Troubleshooting Chart
If you are experiencing a problem that is not listed in this chart, see
your authorized dealer for service.
When you have checked all the possible causes listed and you are
still experiencing the problem, see your authorized dealer
Engine
IF CHECK
Engine will not start Battery has low voltage.
Loose or corroded battery connections.
Blown fuse(s).
Spark plug wire(s) is loose or disconnected.
Faulty spark plug(s) or coil.
No fuel or improper fuel.
Plugged fuel filter.
Defective starter solenoid.
Open-circuit in wiring.
Engine is hard to start Engine is cold.
Engine oil viscosity too heavy.
Spark plug(s) is fouled.
Faulty spark plug(s) or wire(s).
Loose or corroded electrical connections.
Stale or improper fuel.
Engine misses under load Faulty spark plug(s).
Stale or dirty fuel.
Faulty coil or wire.
Engine vapor locks Poor quality fuel or methanol.
Very hot weather conditions and very high loading condition.
Fuel tank vent plugged.
Dirt in fuel filter.
Engine runs unevenly Loose electrical connections.
Throttle cable sticking.
Fuel line or fuel filter plugged.
Stale or dirty fuel.
Improper fuel.
Air cleaner element plugged.
Spark plug(s) is fouled.
Engine overheats Air cleaner element missing or plugged.
Engine oil low.
Engine operated too long at slow engine speed.
Bleed cooling system.
Check thermostat.
Check water pump.
Check coolant level.
Engine loses power Engine overheating.
Too much oil in engine.
Faulty spark plug(s).
Fuel supply being restricted.
Fuel filter plugged
Fuel line pinched or kinked.
Improper fuel.
Air cleaner element plugged.
Engine knocks Low engine speed.
Stale or low octane fuel.
Engine overloaded.
94

Troubleshooting
Electrical
IF CHECK
Starter does not work Loose or corroded connections.
Low battery output.
Sulfated or worn out battery.
Faulty starter.
Starter cranks slowly Low battery output.
Engine oil too heavy.
Loose or corroded connections.
Entire electrical system does not work Blown fuse.
Dead battery Shorted starter solenoid.
Key switch not turned to STOP position.
Component connected to accessory outlet left on with engine off.
Turn signal and/or hazard lights left on with engine off.
Low engine speed or excessive idling.
Battery cables and terminals are dirty.
Dead cell in the battery.
Faulty charging system.
Current draw higher than charging system output. (If several attachments
are added and used frequently at the same time with the standard
charging system. Especially at low engine speeds.)
Correct indicator light(s) do not come on when checking instrument Faulty bulb.
panel. Faulty wiring.
Faulty switch or sensor.
Battery will not take a charge Dead cell in battery.
Electrolyte level low.
Low engine speed or excessive idling.
Faulty charging system.
Headlights dim or flicker Current draw higher than charging system output. (If installed, Electric
Power Assist Steering will draw current.)
Brakes
IF CHECK
Brakes not working correctly Brake fluid level low - check fluid level.
Air in brake system, system not bled properly.
Replace worn brake pads. (See your John Deere dealer.)
Cargo Box
IF CHECK
Tailgate doesn’t latch properly Bushings worn/damaged - inspect bushings.
Strikers not connecting - inspect and lubricate strikers.
Power lift doesn’t operate No power - check all power connections.
Actuator motor overheated - allow actuator to cool.
Power lift actuator rachets/clicks/squeals when operating Too much weight in box - remove weight or move it rearward in box.
Steering
IF CHECK
Steering effort feels “heavy” Current draw higher than charging system output. (If installed, Electric
Power Assist Steering will draw current.) Turn off optional equipment.
Tire pressure or tread below recommended levels.
Toe-in may need adjustment.
Electric Power Steering Assist (EPAS) malfunction.
95

Storage
Storing Safety 2. Turn on engine and allow to run until it runs out of
fuel.
CAUTION: Avoid injury! Fuel vapors are
explosive and flammable. 3. For machines equipped with key switch, turn key to
off position.
Engine exhaust fumes contain carbon monoxide
and cause serious illness or death: IMPORTANT: Avoid damage! Stale fuel can produce
varnish and plug carburetor or injector
• Run the engine only long enough to move the
components and affect engine performance.
ma c h in e to o r from s to rag e.
• If a mac hin e is s tored b efo re allo w in g it t o • A dd fu el c o nd ition er o r s ta biliz e r to fres h fu el
c o o l , m a c h i n e fifirre s a n d s t r u c t u r e fifirre s c a n b e f o r e fifilll i n g t a n k .
o c c u r. F i r e s c a n o c c u r i f d e b r i s i s n o t 4. Mix fresh fuel and fuel stabilizer in separate
r e m o v e d f r o m a r o u n d t h e e n g i n e a n d m u f flfle er, container. Follow stabilizer instructions for mixing.
o r if s to re d ne ar c o mbu s tible mate rials .
5. Fill fuel tank with stabilized fuel.
• Do not store vehicle with fuel in the tank
in s ide a bu ilding wh ere fume s re ac h an o pe n 6. Run engine for a few minutes to allow fuel mixture to
flfla
am e o r s p a r k . circulate through carburetor on gas engine or fuel
• Allow the engine to cool before storing the injectors on diesel engine.
ma ch in e in an y en clo sure.
Engine:
Engine storage procedure should be used when vehicle
is not to be used for longer than 60 days.
Preparing Machine for Storage
1. Repair any worn or damaged parts. Replace parts if 1. Change engine oil and filter while engine is warm.
necessary. Tighten loose hardware. 2. Service air filter if necessary.
2. Repair scratched or chipped metal surfaces to 3. Clean debris from engine air intake screen.
prevent rust.
4. On gas engines:
3. Remove grass and debris from machine. • Remove spark plugs. Put 30 mL (1 oz.) of clean
4. Wash the machine with low pressure water and engine oil in cylinders.
apply wax to metal and plastic surfaces. • Install spark plugs, but do not connect spark plug
5. Run machine for five minutes to dry belts and wires.
pulleys. • Crank the engine 5 or 6 times to allow oil to be
distributed.
6. Apply light coat of engine oil to pivot and wear points
to prevent rust. 5. Clean the engine and engine compartment.
7. Lubricate grease points. 6. Remove battery.
8. Check tire pressure. 7. Clean the battery and battery posts. Check the
electrolyte level, if your battery is not maintenance
free.
Preparing Fuel and Engine For Storage 8. Close fuel shut-off valve, if your machine is
equipped.
Fuel:
9. Store the battery in a cool, dry place where it will not
If you have been using “Stabilized Fuel,” add stabilized freeze.
fuel to tank until the tank is full.
NOTE: The stored battery should be recharged every 90
NOTE: Filling the fuel tank reduces the amount of air in days.
the fuel tank and helps reduce deterioration of fuel.
10. Charge the battery.
If you are not using “Stabilized Fuel:” IMPORTANT: Avoid damage! Prolonged exposure to
1. Park machine safely in a well-ventilated area. (See sunlight could damage the hood surface. Store
Parking Safely in the SAFETY section.) machine inside or use a cover if stored outside.
NOTE: Try to anticipate the last time the machine will be 11. Store the vehicle in a dry, protected place. If vehicle
used for the season so very little fuel is left in the is stored outside, put a waterproof cover over it.
fuel tank.
96

Storage
Removing Machine From Storage
1. Check tire pressure.
2. Check engine oil level.
3. Check battery electrolyte level, if your battery is not
maintenance free. Charge battery if necessary.
4. Install battery.
5. On gas engines: Check spark plug gap. Install and
tighten plugs to specified torque.
6. Lubricate all grease points.
7. Open fuel shut-off valve, if your machine is equipped.
8. Be sure all shields and guards or deflectors are in
place.
97

Specifications
Engine
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-cycle Gas, Electronic Fuel Injection (EFI)

Cylinders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spin On Filter
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dry replaceable single element with remote intake
Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Liquid
Drive Train and Travel Speeds
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuously Variable Transmission (CVT) with Clutch Enclosure

Gear Ranges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Forward HI and LO - Neutral - Reverse
Travel Speeds:
Forward HI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 km/h (44 mph)
Forward LO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 km/h (27 mph)
Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 km/h (30 mph)
Electrical System
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Volt
Battery Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 Cold Cranking Amps @ -18°C (0°F)
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Amp
Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.95 mm (0.04 in.)
Fuel System
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replaceable Element

Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gasoline
Steering and Brakes
Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rack and Pinion

Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic Disc
Tires
NOTE: All tire load conditions are not to exceed Gross
Vehicle Weight Rating (GVWR).
All tires can carry permissible axle loads.
Front Tires
CST Terra Hawk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25x9-12
Load Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 kg (1168 lb)
CST Ancla. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26x9-12
Maxxis Bighorn 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27x9-R14
Inflation Pressure (All Front Tires). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 kPa (14 psi)
Rear Tires
CST Terra Hawk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25x11-12
Inflation Pressure - Cargo Load Condition 0-318 kg (0-700 lbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 kPa (14 psi)
Inflation Pressure - Cargo Load Condition 318-454 kg (700-1000 lbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 kPa (22 psi)
98

Specifications
CST Ancla. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26x11-12
Maxxis Bighorn 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27x11-R14
Capacities
Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26.5 L (7.0 gal)

Crankcase (with filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 L (2.3 qt)
4WD Front Differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 L (19.6 oz)
Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 L (4.0 qt)
Cooling system (Including recovery tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 L (5.2 qt)
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 ML (12 oz)
Dimensions
Width (overall) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 m (62 in.)

Length (with bumper) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.94 m (155 in.)
Height (with OPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.89 m (74.4 in.)
Ground Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26.7 cm (11.0 in.)
Weights
Weight (Empty vehicle with full fluids) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 934 kg (2059 lb)

Gross Vehicle Weight Rating (GVWR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1542 kg (3400 lb)
Payload Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 635 kg (1400 lb)
Cargo Box Capacity (Not to exceed GVWR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454 kg (1000 lb)
Towing Capacity (Not to exceed GVWR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680 kg (1500 lb)
Maximum Trailer Tongue Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 kg (150 lb)
Maximum Front Axle Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650 kg (1433 lb)
Maximum Rear Axle Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050 kg (2315 lb)
Recommended Lubricants
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . John Deere PLUS-4™

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . John Deere TURF-GARD™
Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . John Deere Multi-Purpose HD Lithium Complex Grease
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grease-Gard™ Premium Plus
Transmission Oil (Transaxle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . John Deere HY-GARD™ (JDM J20C)
Transmission Oil (4WD Front Differential) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . John Deere HY-GARD™ (JDM J20C)
Park Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . John Deere HY-GARD™ (JDM J20C)
(Specifications and design subject to change without

notice.)
99

Warranty
Product Warranty maintenance of your off-road utility vehicle engine and
John Deere offers a standard warranty on new John equipment.
Deere products. For a copy of the product warranty Your emissions control system may include parts such as
statement or for details on the warranty terms and the carburetor, fuel hose, fuel-injection system and
conditions for products purchased in the United States ignition system. Also included may be connectors and
and Canada, please contact your local John Deere other emissions related assemblies.
Dealer or utilize the following resources:
Where a warrantable condition exists, John Deere will
United States repair your off-road utility vehicle engine and equipment
at no cost to you including diagnosis, parts and labor.
Website:
http://www.deere.com/en_US/services_and_support/ John Deere Emission Control System Warranty
warranty/warranty.page Coverage
2008 and later off-road utility vehicle engines and
Toll Free: 1-800-537-8233
equipment emissions control related parts are warranted
Dealer Locator: by John Deere as follows: For vehicles without an
odometer the emissions warranty period is 30 months.
http://dealerlocator.deere.com/servlet/country=US
For vehicles with an odometer the emissions warranty
Canada period is 30 months, 500 hours or 5000 kilometers,
whichever comes first. In no event shall the emissions
Website (English): related warranty be less than any published warranty
http://www.deere.ca/en_CA/services_and_support/ offered without charge for the engine. If any emissions
service_plans_warranties/service_plans_ related part on your engine or equipment is defective, the
warranties.page part will be repaired or replaced by John Deere.
Website (French): Owner’s Warranty Responsibilities

http://fr.deere.ca/en_CA/services_and_support/ As the off-road utility vehicle engine and equipment
service_plans_warranties/service_plans_ owner, you are responsible for the performance of the
warranties.page required maintenance listed in your owner’s manual.
John Deere recommends that you retain all receipts
Toll Free: 1-800-537-8233 covering maintenance on your off-road utility vehicle
Dealer Locator: engine and equipment, but John Deere cannot deny
warranty solely for lack of receipts or for your failure to
http://dealerlocator.deere.com/servlet/country=CA ensure all scheduled maintenance is performed.
Emission-related warranties are included in this As the off-road utility vehicle engine and equipment
Operator’s Manual, and applicable if required by law owner, you should however be aware that John Deere
or regulation. may deny you warranty coverage if your off-road utility
For products purchased in a country other than the vehicle engine and equipment or a part has failed due to
United States or Canada, please contact your local John abuse, neglect, improper maintenance or unapproved
Deere dealer for assistance. modifications.
You are responsible for presenting your off-road utility
vehicle engine and equipment to an authorized John
Deere Turf and Utility retailer as soon as a problem
John Deere and Federal Emissions Control exists. The warranty repairs should be completed in a
System Warranty Statement (Off-Road reasonable amount of time, not to exceed 30 days.
Utility Vehicle Gas over 25 MPH)
If you have a question about your emissions warranty
Your Warranty Rights and Obligations coverage, how to make an emissions warranty claim or
The United States Environmental Protection Agency how to make arrangements for emissions-related
(EPA) and John Deere are pleased to explain the authorized repairs, you should contact your John Deere
emissions control system warranty on your off-road utility Turf and Utility retailer, or the John Deere Customer
vehicle engine and equipment. 2008 and later model Contact Center at 1-800-537-8233, or email John Deere
year off-road utility vehicle engines and equipment must from https://groundscare.custhelp.
be designed, built and equipped to meet the U.S. EPA com/app/utils/login_form/redirect/ask.
regulations for off-road utility vehicles with spark ignition
Length of Warranty Coverage
engines. John Deere must warrant the emissions control
system on your off-road utility vehicle engine and John Deere warrants to the initial owner and each
equipment for the period of time listed below provided subsequent purchaser that the off-road utility vehicle
there has been no abuse, neglect or improper engine and equipment is:
100

Warranty
• Designed, built and equipped so as to conform with all • Valves and Switches: vacuum, temperature, position,
applicable regulations of the United States check, time-sensitive
Environmental Protection Agency (EPA) for 2008 and • Electronic controls
later equipment engines; and
• Hoses, belts, connectors and assemblies
• Free from defects in materials and workmanship
which can cause the failure of an emissions warranted Since emissions related parts may vary slightly from
part as follows: For vehicles without an odometer the model to model, certain models may not contain all of
emissions warranty period is 30 months. For vehicles these parts and certain models may contain functionally
with an odometer the emissions warranty period is 30 equivalent parts.
months, 500 hours or 5000 kilometers, whichever
comes first, after the engine and equipment is Warranty Service and Charges
delivered to the initial retail purchaser. In no event Warranty service shall be provided during customary
shall the emissions related warranty be less than any business hours at any authorized John Deere Turf and
published warranty offered without charge for the Utility retailer. Repair or replacement of any warranted
engine. John Deere is liable for damages to other part will be performed at no charge to the owner,
engine components caused by the failure of a including diagnostic labor which leads to the
warranted part during the warranty period. If any determination that a warranted part is defective, if the
emissions related part on your engine or equipment is diagnostic work is performed at an authorized John
defective, the part will be repaired or replaced by John Deere Turf and Utility retailer. Any parts replaced under
Deere. this warranty shall become the property of John Deere.
Warranted Parts
Maintenance Warranty Coverage
Coverage under this warranty includes, but is not limited
a) Any warranted part that is not scheduled for
to, the parts listed below (the emissions control system
parts) to the extent these parts were present on the replacement as required maintenance is warranted as to
defects for the warranty period. Any such part repaired or
engine and equipment purchased.
replaced under the warranty is warranted for the
Fuel Metering System: remaining warranty period.
• Carburetor and internal parts (or fuel injection system) b) Any warranted part that is scheduled only for regular
• Air/fuel ratio feedback and control system inspection to the effect of “repair or replace as
necessary” is warranted as to defects for the warranty
• Cold start enrichment system
period. Any such part repaired or replaced under the
Evaporative System: warranty is warranted for the remaining warranty period.
• Fuel tank, fuel cap and tether c) Any warranted part which is scheduled for
replacement as required maintenance is warranted as to
• Fuel hose, line, fittings, clamps defects only for the period of time up to the first
• Fuel pump, fuel shutoff valve scheduled replacement for that part. Any such part
• Fuel vapor hoses, fittings repaired or replaced under the warranty is warranted for
the remainder of the period prior to the first scheduled
• Carbon canister
replacement point for that part.
• Rollover/slant valve for fuel vapor control
d) Normal maintenance, replacement or repair of
• Purge and vent line
emissions control devices and systems, which are being
Air Induction System: done at the customer’s expense, may be performed by
any qualified repair establishment or individual; however,
• Air cleaner warranty repairs must be performed by an authorized
• Intake manifold John Deere Turf and Utility retailer.
Ignition System: e) Any replacement part that is equivalent in performance

and durability may be used in the performance of any
• Spark plugs non-warranty maintenance or repairs, and shall not
• Magneto or electronic ignition system reduce the warranty obligations of John Deere.
• Spark advance/retard system Consequential Warranty Coverage
Exhaust System: Warranty coverage shall extend to the failure of any
engine components caused by the failure of any
• Exhaust manifold warranted part still under warranty.
• Catalyst muffler
Miscellaneous Items Used in Above Systems:
101

Warranty
Limitations Limited Battery Warranty For Factory
This Emissions Control System Warranty shall NOT Installed Batteries
cover any of the following:
NOTE: Applicable in North America only. For complete
a) Repair or replacement required as a result of (i) machine warranty, reference a copy of the John
misuse or neglect, (ii) improper maintenance or Deere warranty statement. Contact your John
unapproved modifications, (iii) repairs improperly Deere dealer to obtain a copy.
performed or replacements improperly installed, (iv) use
of replacement parts or accessories not conforming to
John Deere specifications which adversely affect TO SECURE WARRANTY SERVICE
performance and/or durability, (v) alterations or The purchaser must request warranty service from a
modifications not recommended or approved in writing John Deere dealer authorized to sell John Deere
by John Deere. batteries, and present the battery to the dealer with the
b) Replacement parts, other services and adjustments top cover plate codes intact.
necessary for normal maintenance.
FREE REPLACEMENT PERIOD
c) Transportation to and from the John Deere Turf and Any new battery which becomes unserviceable (not
Utility retailer, or service calls made by the retailer. merely discharged) due to defects in material or
workmanship within the FREE REPLACEMENT
Limited Liability PERIOD will be replaced free of charge. Installation
a) The liability of John Deere under this Emissions costs will be covered by warranty if the unserviceable
Control System Warranty is limited solely to the battery was installed by a John Deere factory or dealer
remedying of defects in materials or workmanship. This and the replacement battery is installed by a John Deere
warranty does not cover inconvenience or loss of use of dealer.
the off-road utility vehicle engine and equipment or
transportation of the equipment to or from the John PRO RATA ADJUSTMENT (batteries with letter code
Deere Turf and Utility retailer. John Deere shall not be identification only)
liable for any other expense, loss, or damage, whether Any new battery which becomes unserviceable (not
direct, incidental, consequential (except as listed above merely discharged) due to defects in material or
under “coverage”) or exemplary arising in connection workmanship within the Pro Rata Warranty Period will be
with the sale or use of or inability to use the off-road utility replaced upon payment of the battery’s current list price
vehicle engine and equipment for any other purpose. less a pro rata credit for unused months of service. The
b) No express emissions control system warranty is applicable adjustment period is determined from the
given by John Deere with respect to the engine and Warranty Code printed at the top of the battery and table
equipment except as specifically set forth in this below. Installation costs are not covered after the battery
document. Any emissions control system warranty warranty period has ended.
implied by law, including any warranty of merchantability THIS WARRANTY DOES NOT COVER
or fitness for a particular purpose, is expressly limited to
the emissions control system warranty terms set forth in A. Breakage of the container, cover, or terminals.
this document. B. Depreciation or damage caused by lack of reasonable
c) No dealer is authorized to modify this John Deere and and necessary maintenance or by improper
Federal Emissions Control System Warranty. maintenance.
C. Transportation, mailing, or service call charges for
warranty service.
Tire Warranty D. Batteries that are merely discharged.
John Deere warranty applies for tires available through
the John Deere parts system. For tires not available LIMITATION OF IMPLIED WARRANTIES AND
through the John Deere parts system, the tire PURCHASER’S REMEDIES
manufacturer’s warranty applicable to your machine may To the extent permitted by law, neither John Deere nor
not apply outside the U.S. (See your John Deere dealer any company affiliated with it makes any warranties,
for specific information.) representations, or promises as to the quality,
performance or freedom from defect of the products
covered by this warranty. IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, TO THE EXTENT
APPLICABLE, SHALL BE LIMITED IN DURATION TO
THE APPLICABLE ADJUSTMENT PERIOD SET
FORTH HERE. THE PURCHASER’S ONLY REMEDIES
102

Warranty
IN CONNECTION WITH THE BREACH OR
PERFORMANCE OF ANY WARRANTY ON JOHN
DEERE BATTERIES ARE THOSE SET FORTH HERE.
IN NO EVENT WILL THE DEALER, JOHN DEERE OR
ANY COMPANY AFFILIATED WITH JOHN DEERE BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. (Note: Some states do not allow limitations
on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages. So
these limitations and exclusions may not apply to you.)
This warranty gives you specific legal rights, and you
may also have some rights which vary from state to state.
NO DEALER WARRANTY
The selling dealer makes no warranty of its own and the
dealer has no authority to make any representation or
promise on behalf of John Deere, or to modify the terms
or limitations of this warranty in any way.
WARRANTY TERMS TABLE

NOTE: If your battery is not labeled with a warranty code,
it is a warranty code 6.
Warranty Code Free Replacement Pro Rata Warranty

Period Period
A 90 Days 40 Months
B 90 Days 36 Months
C 90 Days 24 Months
D 12 Months 48 Months
E 90 Days 12 Months
F 90 Days 60 Months
G 12 Months 60 Months
H 12 Months 60 Months
6 6 Months 0 Months
12 12 Months 0 Months
18 18 Months 0 Months
103

John Deere Quality Statement
John Deere Quality C. Then call 1-800-537-8233 (United States and
John Deere equipment is more than just a purchase, it’s Canada) and our advisor will work with your dealer to
an investment in quality. That quality goes beyond our investigate your concern. If you are outside the United
equipment to your John Deere dealer’s parts and service States and Canada, visit the following website:
support. This support is needed to keep you a satisfied http://www.deere.com/globalhome/
customer. deerecom/global_home.page?CC=true
That’s why John Deere has initiated a process to handle Select your country and then click on the Contact Us link.
your questions or problems, should they arise. The
following three steps will help guide you through the
process.
Step 1
Refer to your operator’s manual
A. It has many illustrations and detailed information on
the safe and proper operation of your equipment.
B. It gives troubleshooting procedures, and specification
information.
C. It gives ordering information for parts catalogs, service
and technical manuals.
D. If your questions are not answered in the operator’s
manual, then go to Step 2.
Step 2
Contact your dealer
A. Your John Deere dealer has the responsibility,
authority, and ability to answer questions, resolve
problems, and fulfill your parts and service needs.
B. First, discuss your questions or problems with your
dealer’s trained parts and service staff.
C. If the parts and service people are unable to resolve
your problem, see the dealership manager or owner.
D. If your questions or problems are not resolved by the
dealer, then go to Step 3.
Step 3
Contact John Deere
A. Your John Deere dealer is the most efficient source in
addressing any concern, but if you are not able to resolve
your problem after checking your operator’s manual and
contacting your dealer, contact John Deere for
assistance.
B. For prompt, effective service, please have the
following ready before you call:
• The name of the dealer with whom you’ve been
working.
• Your equipment model number.
• Number of hours on machine (if applicable).
• Your serial number which you recorded on the inside
front cover of this manual.
• If the problem is with an attachment, your attachment
identification number.
104

Service Record
Record Service Dates
Oil Change Oil Filter Change Lubricate Machine Air Cleaner Element Fuel Filter Change Coolant Change
Check/Clean
105

Index
4 F
4WD Front Differential Oil, Changing. . . . . . . . . . . . 70 Filter, Changing Engine Oil . . . . . . . . . . . . . . . . . . . 55
4WD Front Differential Oil, Checking . . . . . . . . . . . . 70 Fluid, Brake. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
A Four Wheel Drive, Using . . . . . . . . . . . . . . . . . . . . 35
Accessory Outlet, Using . . . . . . . . . . . . . . . . . . . . . 33 Front Blade Switch, Using . . . . . . . . . . . . . . . . . . . 33
Adjustment, Altitude . . . . . . . . . . . . . . . . . . . . . . . . 54 Front Differential Oil, 4WD . . . . . . . . . . . . . . . . . . . 70
Air Cleaner Element, Servicing . . . . . . . . . . . . . . . . 56 Fuel and Stabilizer, Using Proper . . . . . . . . . . . . . . 84
Air Intake, Checking Hoses and Clamps . . . . . . . . . 57 Fuel Filter, Replacing . . . . . . . . . . . . . . . . . . . . . . . 58
Alarm, Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Fuel Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Alternator Belt, Inspecting. . . . . . . . . . . . . . . . . . . . 67 Fuel Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Fuel Tank, Filling . . . . . . . . . . . . . . . . . . . . . . . . . . 84
B Fuse Filaments, Checking . . . . . . . . . . . . . . . . . . . 89
Battery and Terminals, Cleaning . . . . . . . . . . . . . . . 81 Fuses, Replacing. . . . . . . . . . . . . . . . . . . . . . . . . . 82
Battery, Checking the . . . . . . . . . . . . . . . . . . . . . . . 80
Battery, Removing and Installing. . . . . . . . . . . . . . . 80 G
Battery, service safely . . . . . . . . . . . . . . . . . . . . . . 80 Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Battery, Using Booster . . . . . . . . . . . . . . . . . . . . . . 81 H
Bench Seat, Using . . . . . . . . . . . . . . . . . . . . . . . . . 28 Hand Holds, Using. . . . . . . . . . . . . . . . . . . . . . . . . 28
Brakes Hazard Lights, Using . . . . . . . . . . . . . . . . . . . . . . . 33
Brake fluid, checking . . . . . . . . . . . . . . . . . . . . . 77 Headlights, Using. . . . . . . . . . . . . . . . . . . . . . . . . . 31
Brake lines, checking . . . . . . . . . . . . . . . . . . . . . 78 Heater, Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Brake pads, checking. . . . . . . . . . . . . . . . . . . . . 77 Hitch, Front Receiver . . . . . . . . . . . . . . . . . . . . . . . 48
Brakes, Troubleshooting. . . . . . . . . . . . . . . . . . . . . 95 Hood, Opening and Closing . . . . . . . . . . . . . . . . . . 87
Bucket Seats, Using . . . . . . . . . . . . . . . . . . . . . . . 28 I
Bulb, Replacing Headlight . . . . . . . . . . . . . . . . . . . 82 Instrument Display, Using . . . . . . . . . . . . . . . . . . . . 31
Bushings, Tailgate, Replacing . . . . . . . . . . . . . . . . . 89 Instrument Panel, Using Arrow Keys . . . . . . . . . . . . 32
C K
Cab Classification . . . . . . . . . . . . . . . . . . . . . . . . . 45 Key Switch, Using . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cargo Box, Emptying . . . . . . . . . . . . . . . . . . . . . . . 42
Cargo Box, Loading . . . . . . . . . . . . . . . . . . . . . . . . 41 L
Cargo Box, Troubleshooting . . . . . . . . . . . . . . . . . . 95 Labels, safety no-text. . . . . . . . . . . . . . . . . . . . . . . 11
Cargo Box, Using . . . . . . . . . . . . . . . . . . . . . . . . . 36 Labels, safety text . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cargo Rack, Using. . . . . . . . . . . . . . . . . . . . . . . . . 34 Lifting Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Chains, Tire, Using . . . . . . . . . . . . . . . . . . . . . . . . 43 Lights, Optional, Replacing Bulbs . . . . . . . . . . . . . . 46
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Load Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Clutch, Enclosure, Cleaning . . . . . . . . . . . . . . . . . . 75 Loads, Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Controls, Operator . . . . . . . . . . . . . . . . . . . . . . . . . 26 M
Coolant, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Metal Surfaces, Repairing and Cleaning . . . . . . . . . 92
Coolant Level, Checking . . . . . . . . . . . . . . . . . . . . 61 N
Cooling System, Service Safely . . . . . . . . . . . . . . . 62 Nets or doors, inspecting . . . . . . . . . . . . . . . . . . . . 88
Cooling System, Servicing . . . . . . . . . . . . . . . . . . . 62
CV Boots, Checking. . . . . . . . . . . . . . . . . . . . . . . . 72 O
Oil, Checking Engine . . . . . . . . . . . . . . . . . . . . . . . 54
D Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Doors, Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Oil, Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Drive Belt, Checking . . . . . . . . . . . . . . . . . . . . . . . 72 Oil, Transaxle, Changing . . . . . . . . . . . . . . . . . . . . 71
Drive Line, Lubricating . . . . . . . . . . . . . . . . . . . . . . 53 Operating Checklist, Daily . . . . . . . . . . . . . . . . . . . 27
Dust Unloading Valve, Cleaning . . . . . . . . . . . . . . . 56
P
E Park Brake, Adjusting. . . . . . . . . . . . . . . . . . . . . . . 79
Electrical, Troubleshooting . . . . . . . . . . . . . . . . . . . 95 Park Brake Fluid, Checking . . . . . . . . . . . . . . . . . . 78
Emergency Stopping . . . . . . . . . . . . . . . . . . . . . . . 35 Park Brake, Using . . . . . . . . . . . . . . . . . . . . . . . . . 30
Engine Compartment, Cleaning . . . . . . . . . . . . . . . 60 Parking Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Engine, Starting the . . . . . . . . . . . . . . . . . . . . . . . . 34 Plastic And Painted Surfaces, Avoid
Engine, Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Damage To . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Engine, Troubleshooting. . . . . . . . . . . . . . . . . . . . . 94 Plastic Surfaces, Cleaning . . . . . . . . . . . . . . . . . . . 91
106

Index
Power Steering, Using . . . . . . . . . . . . . . . . . . . . . . 35
Q
Quick Clamps, Using . . . . . . . . . . . . . . . . . . . . . . . 45
R
Radiator Cooling Fins, Cleaning . . . . . . . . . . . . . . . 61
Radiator Hoses and Clamps, Checking . . . . . . . . . . 65
Rear Screen, OPS . . . . . . . . . . . . . . . . . . . . . . . . . 48
Record service dates . . . . . . . . . . . . . . . . . . . . . . 105
Replacement parts. . . . . . . . . . . . . . . . . . . . . . . . . 51
S
Safety labels, no-text . . . . . . . . . . . . . . . . . . . . . . . 11
Safety labels, text . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety Start System, Testing. . . . . . . . . . . . . . . . . . 30
Safety Systems, Testing . . . . . . . . . . . . . . . . . . . . . 30
Safety, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Seat Belt, Inspecting . . . . . . . . . . . . . . . . . . . . . . . 88
Seat Belt, Using. . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Seats, Removing and Installing. . . . . . . . . . . . . . . . 85
Service Information, Emissions . . . . . . . . . . . . . . . . 54
Service Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Spark Arrestor, Checking . . . . . . . . . . . . . . . . . . . . 68
Spark Arrestor, Using . . . . . . . . . . . . . . . . . . . . . . . 16
Spark Plug, Checking . . . . . . . . . . . . . . . . . . . . . . 58
Storage Areas, Using . . . . . . . . . . . . . . . . . . . . . . . 33
Storage, Preparing Machine for . . . . . . . . . . . . . . . 96
Storage, Removing Machine from . . . . . . . . . . . . . . 97
Storage Tray, Removing and Installing . . . . . . . . . . 87
Storing Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Suspension, High Performance Shocks,
Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Suspension, Standard Shocks, Adjusting. . . . . . . . . 90
T
Timing Belt, Inspecting . . . . . . . . . . . . . . . . . . . . . . 66
Tires, Inflation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Traction Assist, Using . . . . . . . . . . . . . . . . . . . . . . 35
Transaxle, Checking Oil . . . . . . . . . . . . . . . . . . . . . 71
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Travel Controls, Using . . . . . . . . . . . . . . . . . . . . . . 30
Troubleshooting chart. . . . . . . . . . . . . . . . . . . . . . . 94
Turn Signal Switch, Using . . . . . . . . . . . . . . . . . . . 33
W
Warranty, product. . . . . . . . . . . . . . . . . . . . . . . . . 100
Wheel Assembly, Removing and Installing. . . . . . . . 84
Windshield, maintenance . . . . . . . . . . . . . . . . . . . . 93
107

Notes

John Deere Xuv 825i s4 Gator Utility Vehicle Operators Manual

Uploaded by

Copyright:

Available Formats

John Deere Xuv 825i s4 Gator Utility Vehicle Operators Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

John Deere Xuv 825i s4 Gator Utility Vehicle Operators Manual

Uploaded by

Copyright:

Available Formats

What safety features does the vehicle have?

What safety features does the vehicle have?

What maintenance is required for the vehicle?

What maintenance is required for the vehicle?

*DCY*

XUV 825i S4 Gator™ Utility

Gator™ Utility Vehicle XUV 825i S4

Diesel engine exhaust and some of its constituents

If this product contains a gasoline engine:

The State of California requires the above two warnings.

John Deere Horicon Works

Downloaded from manualsnet.com search engine

IMPORTANT: Avoid damage! This text is used to tell

Sections in your operator’s manual are placed in a

Downloaded from manualsnet.com search engine

Original Instructions. All information, illustrations and specifications in this

Downloaded from manualsnet.com search engine

Downloaded from manualsnet.com search engine

A — OPS Label - M156705 H — WARNING - M167669

Downloaded from manualsnet.com search engine

The machine safety labels shown in this section are

HELP PREVENT INJURY WHEN DUMPING LOADS

Downloaded from manualsnet.com search engine

BEFORE LEAVING VEHICLE:

Downloaded from manualsnet.com search engine

Inspect and clean the entire machine and pay special

• Only ride in seat with seat belt on.

Avoid Injury or Death from Rollover or Falling Off

Downloaded from manualsnet.com search engine

Avoid Injury or Death from Rollover or Falling Off

Avoid Injury or Death from Falling Off

Avoid Injury or Death From Falling Off

Avoid Injury or Death from Falling Off

Downloaded from manualsnet.com search engine

Downloaded from manualsnet.com search engine

At several important places on this machine safety signs

Avoid Inujury or Death From Falling Off

• Operate dump with machine stationary and parking

Prevent Equipment Fires

• Clean and inspect the entire machine.

Downloaded from manualsnet.com search engine

Keep away from hot surfaces.

Read Operator’s Manual

Before leaving vehicle:

• This operator’s manual contains important information

Avoid Injury From Tipping

Avoid Serious Injury or Death

Downloaded from manualsnet.com search engine

Avoid Injury or Death From Rollover or

Avoid Injury From Explosion

• Read operator’s manual.

Avoid Injury from Falling

• Do not place gas container inside cargo box bed when

• Do not sit on toolbox.

Downloaded from manualsnet.com search engine

Avoid Injury or Death from Falling Off

• Only ride in seat with seat belt on.

OPS/ROPS Protective Structure Safety and

OCCUPANT PROTECTIVE STRUCTURE

Downloaded from manualsnet.com search engine

DCY