17 4PH Spec Sheet

For more information visit www.SandmeyerSteel.
com
Specification Sheet: Alloy 17-4PH

(UNS S17400) W. Nr. 1.4542 Type 630
A Precipitation-Hardening Martensitic Stainless with High Strength and
Hardness and Good Corrosion Resistance
Alloy 17-4PH (UNS S17400), Type Chemical Analysis
630, is a chromium-nickel-copper Weight % (all values are maximum unless a range is otherwise indicated)
precipitation-hardening martensitic
stainless steel with an addition of
niobium. 17-4PH combines high
Chromium 15.0 min. – 17.5 max. Phosphorus 0.04
strength and hardness with good
corrosion resistance. Nickel 3.0 min. – 5.0 max. Sulfur 0.03
The alloy is furnished in the
Copper 3.0 min. – 5.0 max. Silicon 1.0
solution annealed condition
(Condition A). It should not be used Carbon 0.07 Niobium plus Tantalum 0.15 min. – 0.45 max.
at temperatures above 572°F (300°C)
or for cryogenic service. Optimal Manganese 1.0 Iron Balance
mechanical properties can be
obtained by subjecting the alloy to
age hardening heat treatments. Heat Physical Properties (Condition A)
treatment in the 900°F (482°C) range Density Specific Heat
produces the highest strength. 0.280 Ibs/in3 0.11 BTU/lb-°F @ 70°F
The corrosion resistance of Alloy 7.75 g/cm3 460 J/kg-°C @ 20°C
17-4PH is comparable to 304
stainless steel in most environments, Electrical Resistivity Modulus of Elasticity
and is generally superior to the 400 29.5 Microhm-in at 75°F 28.5 x 106 psi
series stainless steels. It is used in 75 Microhm-cm at 24°C 196 GPa
applications where the combination
of moderate corrosion resistance and Melting Range Thermal Conductivity 212°F (100°C)
unusually high strength are required. 2560 – 2625°F 10.6 BTU-in/ft2 - hr-°F
Alloy 17-4PH can be easily welded 1404 – 1440°C 18.3 W/m-°C
and processed by standard shop
fabrication practices. It is magnetic. Mean Coefficient of Thermal Expansion
Temperature Range
Applications
°F °C in/in °F cm/cm °C
• Aerospace — structural and parts
• Biomedical — hand tools 70 – 800 21 – 427 6.3 x 10-6 11.3 x 10-6
• Chemical Processing
• Food Process Equipment
• Gate Valves Mechanical Properties
• Mechanical Components Room temperature properties (longitudinal direction)
• Nuclear Waste Processing and Guaranteed values (ASTM A693 hot rolled plates).
Storage Table 1
• Oil and Gas Production — foils,
helicopter deck platforms, etc. Y.S. 0.2% UTS Elongation
HEAT TREATMENT
• Pulp and Paper — paper mill MPa ksi MPa ksi %
equipment
Hardening 496 ºC (925 ºF) Min. 1070 155 1170 170 8
Standards 4 hours — air cooling
Typ. 1207 175 1310 190 14
ASTM................ A 693
Hardening 593 ºC (1100 ºF) Min. 790 115 965 140 10
ASME................ SA 693 4 hours — air cooling
Typ. 931 135 1034 150 17
AMS................... 5604
S A N D M E Y E R S T E E L C O M PA N Y
ONE SANDMEYER LANE • PHILADELPHIA, PA 19116-3598
800-523-3663 • +1-215-464-7100 • FAX +1-215-677-1430
Alloy 17-4PH rev 04/18
rev 01/2023 PDF link www.SandmeyerSteel.com
Providing Solutions, With Materials and
Value Added Products, for Process Industries
Corrosion Resistance Machining
Alloy 17-4PH can be machined in
The corrosion resistance of Alloy 17-4PH is comparable to 304 stainless
both the solution treated and
steel in most environments, and is generally superior to the 400 series
precipitation hardened conditions.
stainless steels. It is used in applications where the combination of moderate
Machining characteristics may vary
corrosion resistance and unusually high strength are required. Alloy 17-4PH
according to the hardness of the
has corrosion resistance comparable to 304L in some chemical, dairy, food,
metal. High speed tools are
paper and petroleum applications.
acceptable, but carbide tools are
Alloy 17-4PH in the solution-annealed condition (Condition A) should not preferred. Standard lubrication
generally be put in service. The alloy is subject to brittle fractures and more should be used. Dimensional
sensitive to chloride stress corrosion cracking than the aged material. changes as a result heat treatment
should be taken into account if very
If risks of chloride stress corrosion cracking are present the higher aging stringent tolerances are required.
temperatures should be selected over 1022°F (550°C), preferably 1094°F
(590°C). 1022°F (550°C) is the recommended tempering temperature in
chloride service. 1094°F (590°C) is preferred in H2S media.
The information and data in this product
Alloy 17-4PH is subject to crevice corrosion and pitting attack when data sheet are accurate to the best of our
exposed to stagnant seawater for a duration of time. knowledge and belief, but are intended for
informational purposes only, and may be
revised at any time without notice.
Applications suggested for the materials are
Fabrication Data described only to help readers make their own
evaluations and decisions, and are neither
Alloy 17-4PH can be easily welded and processed by standard shop guarantees nor to be construed as express or
fabrication practices. It is magnetic. implied warranties of suitability for these or
other applications.
Heat Treatment
Alloy 17-4PH is provided in the solution-annealed condition (Condition A).
Mechanical properties may be altered by subsequent age hardening
treatments. These aging treatments are referred to as Conditions H900,
H1025, H1075, H1150, H1150M and H1150D. The processes are outlined in
Table 2 below. The resultant mechanical properties appear above in Table 1.
Table 2
CONDITION Temperature °F Time, h Quench
H900 900 4 Air Cool
H1025 1025 4 Air Cool
H1075 1075 4 Air Cool
H1150 1150 4 Air Cool
H1150M 1400 for 2 h, air cool plus 1150 for 4 h, air cool
H1150D 1400 for 2 h, air cool plus 1150 for 4 h, air cool
Hot Forming
Heat uniformly at 1742 – 2192°F (950 – 1200°C). A full solution anneal,
cooling lower than 76°F (25°C) and aging at the required temperature must
occur after hot forming. The post forming heat treatment should be a function
of the desired mechanical properties.
Cold Forming
Alloy 17-4PH has limited cold forming properties. Cold forming can only be
undertaken on plates in the fully annealed condition. Stress corrosion
resistance is enhanced by re-aging at the precipitation hardening temperature
after cold working.
Cutting
Thermal cutting operations such as plasma cutting should be avoided.
Mechanical cutting operations such as bandsaw, abrasive waterjet, shearing
and machining are preferred.
Welding
Alloy 17-4PH can be readily welded by most standard processes including SANDMEYER
SMAW, GTAW, PAW and GMAW. S T E E L C O M PA N Y

17 4PH Spec Sheet

Uploaded by

Copyright:

Available Formats

17 4PH Spec Sheet

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

17 4PH Spec Sheet

Uploaded by

Copyright:

Available Formats

For more information visit www.SandmeyerSteel.

Specification Sheet: Alloy 17-4PH

CONDITION Temperature °F Time, h Quench

H900 900 4 Air Cool

H1025 1025 4 Air Cool

H1075 1075 4 Air Cool

H1150 1150 4 Air Cool

You might also like