GX2400 e Om Eng Em067n201 2005M-BC-1

Owner’s Manual
MATRIX NMEA2000 GPS

GX2400GPS
GX2400GPS/E (European Version)
zz International ITU-R M.493-15 Class D DSC (Digital Selective Calling)

zz Integrated dual channel AIS (Automatic Identification System) receiver
zz AIS/AIS SART target display: MMSI, Call Sign, Ship Name, BRG, DST, SOG and COG
zz NMEA 2000 and NMEA0183 Compatible
zz Integrated 66 Channel Internal GPS receiver
zz Contact Class A or B AIS Ship with DSC
zz Programmable CPA or TCPA collision avoidance alarms
zz Submersible IPX8 (1.5 meter for 30 minutes)
zz 80dB Commercial grade receiver
zz DSC position request and report functions
zz GM (Group Monitor) using DSC Group Position Calling
zz Navigation (LAT/LON, SOG and COG) information shown on display
zz MOB (Man Over-Board) Operation
zz Versatile user-programmable scanning, priority scan and Dual/Triple Watch
zz Integrated 32 Code Voice Scrambler and 4 Code Voice Scrambler
zz 30 Watt PA/Loud Hailer with preprogrammed fog signals and listen back
zz Noise canceling for both transmit and receive audio
zz Second Station Remote Microphone*
zz Intercom Feature between Radio and Second Station Remote Microphone*
zz ATIS Mode for European Inland Waterways (GX2400GPS/E only)
*(Optional SSM-70H (RAM4) or SSM-72H (RAM4X) required)
TABLE OF CONTENTS
QUICK REFERENCE ............................................ 2 9.11 PRESET CHANNELS: INSTANT ACCESS .......................... 36
9.11.1 Programming ......................................................... 36
1 GENERAL INFORMATION ............................. 3 9.11.2 Operation ............................................................... 36
2 PACKING LIST ................................................ 4 9.11.3 Deletion .................................................................. 37
3 OPTIONAL ACCESSORIES ........................... 4 9.12 MOB OPERATION .................................................................. 37
4 ONLINE WARRANTY REGISTRATION .......... 4 9.13 PA/FOG OPERATION ............................................................ 38
9.13.1 Operating the PA HAIL mode ................................. 38
5 Safety Precautions (Be Sure to Read) ......... 5 9.13.2 Operating the FOG HORN mode ........................... 39
6 GETTING STARTED ....................................... 7 9.13.3 Fog Signal Timing Chart ........................................ 39
6.1 ABOUT VHF RADIO .................................................................... 7 9.14 INTERCOM OPERATION ...................................................... 40
6.2 SELECTING AN ANTENNA ........................................................ 7 9.14.1 Communication ...................................................... 40
6.3 COAXIAL CABLE ......................................................................... 7 9.14.2 Calling .................................................................... 41
6.4 DISTRESS AND HAILING (CHANNEL 16) ................................ 8 9.15 INTERCOM OPERATION ...................................................... 41
6.5 CALLING ANOTHER VESSEL (CHANNEL 16 OR 9) .............. 9 9.15.1 Communication ...................................................... 41
9.15.2 Calling .................................................................... 42
6.6 WHAT IS THE RANGE FOR AIS RECEIVERS? ..................... 10 9.16 VOICE SCRAMBLER ............................................................. 42
6.7 Accuracy of COG ........................................................................ 10 9.17 DEMO MODE .......................................................................... 42
7 CONTROLS AND INDICATORS ................... 11 10 GPS OPERATION ......................................... 44
7.1 FRONT PANEL ........................................................................... 11 10.1 DISPLAYING POSITION INFORMATION ............................ 44
7.2 MICROPHONE .......................................................................... 13 10.1.1 GPS Information Numerical Display ...................... 44
7.3 REAR PANEL ............................................................................. 14 10.1.2 GPS Information Compass Display ....................... 44
8 INSTALLATION ............................................. 16 10.2 CHECKING GPS STATUS ..................................................... 44
8.1 SAFETY / WARNING INFORMATION ..................................... 16 10.3 GPS LOGGER OPERATION ................................................. 45
8.2 LOCATION .................................................................................. 16 11 DIGITAL SELECTIVE CALLING (DSC) ........ 46
8.3 MOUNTING THE RADIO .......................................................... 16 11.1 GENERAL ................................................................................ 46
8.3.1 Supplied Mounting Bracket ....................................... 16 11.2 DISTRESS ALERT .................................................................. 46
8.3.2 Optional MMB-84 Flush Mount Bracket .................... 17 11.2.1 Transmitting a Distress Alert .................................. 46
8.4 ELECTRICAL CONNECTIONS ................................................ 18 11.2.2 Receiving a Distress Alert ...................................... 49
8.5 CONNECTION OF EXTERNAL DEVICES TO THE RADIO .... 19 11.3 ALL SHIPS CALL .................................................................... 50
8.5.1 Connecting the NMEA 0183/NMEA 0183-HS to the Radio .... 19 11.3.1 Transmitting an All Ships Call ................................ 50
8.5.2 Accessory Cables ..................................................... 19 11.3.2 Receiving an All Ships Call .................................... 51
8.5.3 Internal GPS (DSC Output) to Chart Plotter ............. 20 11.4 INDIVIDUAL CALL .................................................................. 52
8.5.4 Connection to External GPS or Chart Plotter ........... 20 11.4.1 Setting up the Individual / Position Call Directory .... 52
8.5.5 Connection to External PA/HAIL Speaker ................ 21 11.4.2 Setting up the Individual Call Reply ....................... 53
8.5.6 Connecting optional SCU-38 External GPS Antenna .... 21 11.4.3 Enabling the Individual Call Acknowledgment ....... 54
8.5.7 Connecting optional SCU-31 External GPS Antenna .... 21 11.4.4 Transmitting an Individual Call ............................... 54
8.5.8 Optional SSM-70H (RAM4) Microphone .................. 22 11.4.5 Receiving an Individual Call ................................... 56
8.5.9 Optional SCU-30 Wireless Access Point Installation .... 24 11.4.6 Setting up the Individual Call Ringer ...................... 57
8.6 INITIAL SETUP REQUIRED WHEN TURNING ON 11.5 GROUP CALL ......................................................................... 58
THE POWER FOR THE FIRST TIME .... 24 11.5.1 Setting up a Group Call ......................................... 58
8.6.1 Maritime Mobile Service Identity (MMSI) .................. 24 11.5.2 Transmitting a Group Call ...................................... 60
8.7 CONFIRMING GPS SIGNAL (GPS STATUS DISPLAY) ........ 26 11.5.3 Receiving a Group Call .......................................... 61
8.8 GPS CONFIGURATION ............................................................ 27 11.5.4 Setting up the Group Call Ringer ........................... 62
8.8.1 Setting the GPS Time ............................................... 27 11.6 POSITION REQUEST ............................................................ 62
8.8.2 Setting the Time Area ............................................... 27 11.6.1 Setting up a Position Request Reply .................... 63
8.8.3 Setting the Time Format ........................................... 28 11.6.2 Transmitting a Position Request to Another Vessel .... 63
8.8.4 Setting COG to True or Magnetic ............................. 28 11.6.3 Receiving a Position Request ................................ 65
9 BASIC OPERATION ...................................... 29 11.6.4 Manual Input of Position Information ..................... 65
9.1 TURNING THE TRANSCEIVER ON AND OFF ...................... 29 11.6.5 Setting up a Position Request Ringer .................... 66
9.2 RECEPTION ............................................................................... 29 11.7 POSITION REPORT ............................................................... 66
11.7.1 Transmitting a DSC Position Report Call ............... 66
9.3 TRANSMISSION ........................................................................ 29 11.7.2 Receiving a DSC Position Report Call ................... 68
9.3.1 Transmit Power ........................................................ 30 11.7.3 Navigating to the Reported Position ...................... 68
9.4 BASIC OPERATION OF THE SETUP MENU ......................... 30 11.7.4 Saving the Reported Position as a Waypoint ......... 69
9.5 TRANSMIT TIME-OUT TIMER (TOT) ...................................... 31 11.7.5 Setting up a Position Report Ringer ...................... 69
9.6 SIMPLEX/DUPLEX CHANNEL USE ........................................ 31 11.8 AUTO POSITION POLLING .................................................. 70
9.7 CHANNEL GROUP .................................................................... 31 11.8.1 Setting up the Polling Operation ............................ 70
9.8 NOAA WEATHER CHANNELS (in USA and Canada only) .... 32 11.8.2 Setting up the Polling Time Interval ....................... 70
9.8.1 NOAA Weather Alert (USA version only) .................. 32 11.8.3 Selecting Vessels to be Automatically Polled ........ 70
9.8.2 NOAA Weather Alert Testing .................................... 33 11.8.4 Enabling/Disabling Auto POS Polling .................... 71
9.9 MULTI WATCH (TO PRIORITY CHANNEL) ............................ 33 11.9 DSC TEST ............................................................................... 71
9.9.1 Setup the Multi Watch Operation .............................. 33 11.9.1 Programming MMSI into Individual Directory ......... 71
9.9.2 Starting Dual Watch .................................................. 33 11.9.2 Transmitting a DSC Test to Another Vessel ........... 72
9.10 SCANNING .............................................................................. 34 11.9.3 Receiving a DSC Test Call ..................................... 73
9.10.1 Selecting Scan Type .............................................. 34 11.10 DSC LOG OPERATION ......................................................... 73
9.10.2 Programming Scan Memory .................................. 34 11.10.1 Reviewing and Resending a Transmitted Logged Call .... 73
9.10.3 Memory Scanning (M-SCAN) ................................ 35 11.10.2 Reviewing a Logged DSC RX Distress Alert
9.10.4 Priority Scanning (P-SCAN) ................................... 35 and acknowledgement .... 74
TABLE OF CONTENTS
11.10.3 Reviewing Other Logged Calls ............................. 74 17.9 CHANNEL NAME .................................................................. 107
11.10.4 Deleting Logged Calls from the DSC Log Directory .... 75 17.10 RX LED DIMMER ADJUSTMENT ....................................... 108
12 NAVIGATION ................................................. 76 17.11 NOISE CANCELLATION ...................................................... 108
12.1 WAYPOINT OPERATION ....................................................... 76 17.12 AUDIO FILTER OPERATION ............................................... 109
12.1.1 Starting and Stopping Navigation .......................... 76 17.13 SCRAMBLER SETUP .......................................................... 109
12.1.2 Setting Up Waypoint Directory ............................... 77 17.14 SUMMARY OF THE CANNEL FUNCTION SETUP .......... 110
12.1.3 Selecting the Display Range .................................. 79 18 DSC SETUP ................................................ 111
12.1.4 Selecting the Arrival Range ................................... 79
12.2 ROUTING OPERATION ......................................................... 80 18.1 INDIVIDUAL DIRECTORY .................................................... 111
12.2.1 Setting Up Routing Directory ................................. 80 18.2 INDIVIDUAL REPLY .............................................................. 111
12.2.2 Starting and Stopping Route Navigation ................ 82 18.3 INDIVIDUAL ACKNOWLEDGMENT .................................... 111
12.2.3 Changing the Destination ...................................... 82 18.4 INDIVIDUAL RINGER ............................................................ 111
12.2.4 Selecting Automatic or Manual Routing ................. 82 18.5 GROUP DIRECTORY ........................................................... 111
13 GM OPERATION ........................................... 83 18.6 POSITION REPLY ................................................................ 112
13.1 SETTING UP GM OPERATION ............................................ 83 18.7 AUTO POSITION POLLING ................................................ 112
13.1.1 Setting Up GM Group Directory ............................. 83 18.8 AUTO POSITION INTERVAL ............................................... 112
13.1.2 Setting Up the Polling Time Interval ....................... 84 18.9 AUTO CHANNEL CHANGE ................................................. 112
13.1.3 Enabling/Disabling Transmission 18.10 NO ACTION TIMER .............................................................. 113
during GM Operation ........ 84 18.11 WAIT TIME FOR POSITION FIX ......................................... 113
13.2 STARTING GM OPERATION ................................................ 85 18.12 DSC BEEP ............................................................................. 113
13.2.1 Changing the GM Group Being Monitored ............ 85
13.2.2 Transmitting a DSC Call to a Group Member ........ 86 18.13 SUMMARY OF THE DSC SETUP MENU .......................... 114
13.2.3 Starting Navigation to a Group Member ................ 86 19 GPS SETUP ................................................ 115
14 AUTOMATIC IDENTIFICATION SYSTEM (AIS) ..... 87 19.1 ORDER OF PRIORITY ......................................................... 115
14.1 GENERAL ................................................................................ 87 19.2 COMPASS DIRECTION ....................................................... 115
14.2 AIS OPERATION .................................................................... 87 19.3 LOCATION FORMAT ............................................................ 115
14.2.1 Displaying the AIS Target Information Screen ....... 88 19.4 TIME OFFSET ....................................................................... 116
14.2.2 Changing the AIS Range ....................................... 89 19.5 TIME AREA ............................................................................ 116
14.2.3 Transmitting an Individual Call to an AIS Ship ....... 89 19.6 TIME FORMAT ...................................................................... 116
14.2.4 CPA/TCPA Alarm Functions ................................... 90 19.7 UNITS OF MEASURE .......................................................... 116
14.2.5 Changing the Compass Display ............................ 91 19.8 MAGNETIC VARIATION ....................................................... 116
14.3 AIS SETUP .............................................................................. 91 19.9 NMEA 0183 IN/OUT .............................................................. 117
14.3.1 CPA ........................................................................ 91 19.9.1 Data Speed .......................................................... 117
14.3.2 TCPA ...................................................................... 91 19.9.2 Output Sentences ................................................ 117
14.3.3 CPA/TCPA Alarm ................................................... 92
14.3.4 IGNORE VESSELS ............................................... 92 19.10 INTERNAL GPS UNIT .......................................................... 118
19.10.1 Position Data Output .......................................... 118
15 NMEA 2000 SETUP ...................................... 94 19.10.2 Pinning ............................................................... 119
15.1 SELECT DEVICE .................................................................... 94 19.10.3 Differential GPS ................................................. 119
15.2 DEVICE NUMBER .................................................................. 94 19.10.4 Logger Interval ................................................... 120
15.3 SYSTEM NUMBER ................................................................ 95 19.10.5 Log Erase ........................................................... 120
15.4 SUMMARY OF THE NMEA 2000 SETUP ............................ 95 19.11 SUMMARY OF THE GPS SETUP ...................................... 121
15.5 COMPATIBLE NMEA 2000 PGN LIST .................................. 95 20 ATIS SETUP ................................................ 122
16 CONFIGURATION SETUP ............................ 97 20.1 ATIS CODE PROGRAMMING ............................................. 122
16.1 DISPLAY MODE ...................................................................... 97 20.2 ATIS CH GROUP .................................................................. 123
16.2 DIMMER ADJUSTMENT ........................................................ 97 21 SSM-70H (RAM4) REMOTE MIC OPERATION .... 124
16.3 DISPLAY CONTRAST ............................................................ 97 21.1 REMOTE MIC CONTROLS ................................................. 124
16.4 KEY BEEP ............................................................................... 98 21.2 RAM4 SOFT KEY ASSIGNMENT ....................................... 126
16.5 FOG ALERT TONE FREQUENCY ........................................ 98 21.2.1 Key Assignment ................................................... 127
16.6 LISTEN BACK ......................................................................... 99 22 CONNECTING A USB DATA TERMINAL TO THE PC .... 128
16.7 STATION NAME ...................................................................... 99 23 MAINTENANCE .......................................... 129
16.8 SOFT KEYS .......................................................................... 100 23.1 REPLACEMENT PARTS ...................................................... 129
16.8.1 Key Assignment ................................................... 100 23.2 FACTORY SERVICE ............................................................ 129
16.8.2 Key Timer ............................................................. 102
23.3 TROUBLESHOOTING CHART ........................................... 130
16.9 RESET ................................................................................... 102
16.9.1 Reset the USER MMSI and ATIS CODE ............. 103 24 CHANNEL ASSIGNMENTS ........................ 131
16.10 SUMMARY OF THE CONFIGURATION SETUP ............... 105 24.1 GX2400GPS .......................................................................... 131
17 CHANNEL FUNCTION SETUP ................... 106 24.2 GX2400GPS/E ...................................................................... 134
17.1 CHANNEL GROUP ............................................................... 106 25 SPECIFICATIONS ....................................... 136
17.2 WEATHER ALERT (USA version only) ................................ 106 25.1 DIMENSIONS ........................................................................ 138
17.3 SCAN MEMORY ................................................................... 106 26 FCC RADIO LICENSE INFORMATION ...... 139
17.4 SCAN TYPE .......................................................................... 106 27 FCC NOTICE ............................................... 140
17.5 SCAN RESUME .................................................................... 106 STANDARD HORIZON Limited Warranty.........142
17.6 MULTI WATCH ...................................................................... 106
17.7 PRIORITY CHANNEL ........................................................... 107 TEMPLATE for the GX2400 series....................143
17.8 SUB CHANNEL ..................................................................... 107
QUICK REFERENCE

 

 



 Press and hold the key to turn the radio ON or OFF.

 Rotate the VOL knob to adjust the speaker audio volume.
 Rotate the SQL knob clockwise to squelch or counterclockwise to
un-squelch the radio.
 Rotate the DIAL knob (or press the microphone ▲/▼ keys) to select the
operating channel.
 Press the H/L key to toggle the transmit power between High (25W) and
Low (1W).
 Press the 16/S key on the radio or the microphone to select channel 16.
Press and hold the 16/S key on the radio or the microphone to select sub
channel. Press the 16/S key again to revert to the previously selected
channel.
 To transmit: place the microphone about 2 cm away from your mouth and
speak in a normal voice level while pressing the PTT switch.
2
1 GENERAL INFORMATION
The STANDARD HORIZON GX2400 Marine VHF/FM Marine transceiver is
designed to be used in International, USA, Canadian and other Region Marine
channels. The GX2400 can be operated from 11 to 16 VDC and has a switch-
able RF output power of 1 watt or 25 watts.
The GX2400 integrates a dual channel AIS (Automatic Identification System)
receiver to display class A and B AIS vessel information (MMSI, Call Sign, Ship
Name, BRG, DST, SOG and COG) directly on the LCD display. The GX2400
is also capable of entering and saving up to 250 waypoints, which may be
selected and navigated to by using a unique navigation compass display.
The GX2400 allows you to contact an AIS ship directly using DSC, show your
vessels position in relation to AIS targets and alert you when an AIS ship may
be approaching too close to your location via the Closest Point of Approach
(CPA) Alarm or Time to Closest Point of Approach (TCPA) Alarm.
The GX2400 is capable of DSC (Digital Selective Calling) ITU-R M.493-15 Class
D operation with a 66-channel internal GPS. Class D operation allows continu-
ous reception of Digital Selective Calling functions on channel 70 even while
receiving calls on the voice channels. The GX2400 operates on all currently-
allocated marine channels and is switchable for use with International, USA,
or Canadian regulations. Emergency channel 16 can be immediately selected
from any other channel by pressing the [16/S] key. NOAA weather channel can
also be accessed immediately by pressing the [WX] soft key.
Other features of the GX2400 includes: Noise canceling function for transmit
and receive audio, NMEA 2000 compatibility, high expandability, speaker
microphone, 30 W PA/Loud hailer with preprogrammed fog signals and listen
back, capable of being connected to one optional wired RAM4 or four wireless
RAM4X*1 remote access microphones, allowing full control of all VHF, DSC
and hailer functions remotely including an intercom feature allowing you to
communicate between the radio, RAM4 and wireless RAM4X microphones,
scanning, priority scanning, submersible speaker microphone, high and low volt-
age warning, and GPS repeatability. (*1 requires SCU-30 Wireless Access Port)
3
2 PACKING LIST
Open the package and verify it contains the following items:
 Transceiver
 DC Power Cord
 Mounting Bracket and Hardware
 Owner’s Manual
 DSC Warning Sticker (GX2400GPS Only)
 USB Cable (Type USB “A” plug to Type USB micro “B” plug) T9101648
3 OPTIONAL ACCESSORIES
 Flush-Mount Bracket .................................................................... MMB-84
 Remote-Access Microphone (RAM4 Microphone)*1..................... SSM-70H
*1(The SSM-70H firmware must be Ver. 3.00.00 or later.)
 Wireless Remote Access Microphone (RAM4X Microphone)....... SSM-72H
 Wireless Access Point for SSM-72H*2........................................... SCU-30
*2 (To connect the SSM-72H (RAM4X), the SCU-30 firmware must be
Ver. 2.00.00 or later.)
 USB DC Charger with Cigarette Lighter Plug for SSM-72H ............ SDD-14
 External GPS Antenna with 16 ft (5 m) of Cable ............................ SCU-38
 23 ft (7 m) Extension Cable for SSM-70H ..................................... CT-100
 External Loud Speaker ................................................................. MLS-300
 5” Round 30 Watt Hail/PA Horn .................................................... 220SW
 5” × 8” Rectangular 40 Watt Hail/PA Horn .................................... 240SW
 Dust Cover (White) ....................................................................... HC2400
4 ONLINE WARRANTY REGISTRATION

Please visit www.standardhorizon.com - Owner’s Corner to register the
GX2400 Marine VHF Transceiver.
NOTE: Visiting the STANDARD HORIZON website from time to time may be beneficial.
When new products are released, information will appear on the website.
4
5 Safety Precautions (Be Sure to Read)
Be sure to read these important precautions, and use this product safely.
Yaesu is not liable for any failures or problems caused by the use or misuse of this
product by the purchaser or any third party. Also, Yaesu is not liable for damages
caused through the use of this product by the purchaser or any third party, except in
cases where ordered to pay damages under the laws.
Types and meanings of the marks
This mark indicates an imminently hazardous situation, which, if not
DANGER avoided, could result in death or serious injury.
This mark indicates a potentially hazardous situation, which, if not
WARNING avoided, could result in death or serious injury.
This mark indicates a potentially hazardous situation, which, if not
CAUTION avoided, may result in minor or moderate injury or only property damage.
Types and meanings of symbols

These symbols signify prohibited actions, which must not be done to use this product
safely. For example: indicates that the product should not be disassembled.
These symbols signify required actions, which must be done to use this product safely.
For example: indicates the power plug should be disconnected.
DANGER
Do not operate the device when flammable gas If thunder and lightning develop nearby when
is generated. an external antenna is used, immediately turn
Doing so may result in fire and explosion. this transceiver OFF, and disconnect the exter-
nal antenna from it.
Do not transmit with this device while carrying A fire, electrical shock, or damage may result.
or using a medical appliance such as a cardiac
pacemaker. When transmitting, use an external Do not touch any liquid leaking from the liquid
antenna and keep as far as possible away from display with your bare hands.
the external antenna. There is a risk of chemical burns occurring when
The radio wave emitted by the transmitter can the liquid comes into contact with the skin or gets
cause the medical device to malfunction and result into the eyes. In this case, seek medical treatment
in injury or death. immediately.
WARNING
Do not power this transceiver with a voltage Do not handle the power plug and connector
other than the specified power supply voltage. etc. with wet hands. Also do not plug and un-
A fire, electric shock, or damage may result. plug the power plug with wet hands.
This may result in injury, liquid leak, electric
Do not make very long transmissions.
shock and equipment failure.
The main body of the transceiver may overheat,
resulting component failure or operator burns. Disconnect the power cord and connection
cables before incorporating items sold sepa-
Do not disassemble or make any alteration to
rately or replacing the fuse.
this product.
This may result in fire, electric shock and equip-
An injury, electric shock, or failure may result.
ment failure.
Never touch the antenna during transmission.
This may result in injury, electric shock and
equipment failure.
5
When smoke or strange odors are emitted Do not bend, twist, pull, heat and modify the
from the radio, turn off the power and discon- power cord and connection cables in an un-
nect the power cord from the socket. reasonable manner.
This may result in fire, liquid leak, overheating, This may cut or damage the cables and result in
damage, ignition and equipment failure. Please fire, electric shock and equipment failure.
contact our company customer support or the re-
Do not pull the cable when plugging and unplug-
tail store where you purchased the device.
ging the power cord and connection cables.
Keep the power plug pins and the surround- Always hold the plug or connector when unplug-
ing areas clean at all time. ging; if not, a fire, electric shock and equipment
This may result in fire, liquid leak, overheating, failure may result.
breakage, ignition etc. Do not use the device when the power cord
Never cut the fuse holder off of the DC power and connection cables are damaged, or when
cord. the DC power connector cannot be plugged
This may cause a short circuit and result in igni- in tightly.
tion and fire. Contact Yaesu Amateur Customer Support or
the retail store where this transceiver was pur-
Use only the specified type fuses. chased for assistance, as this may result in fire,
Use of an incorrect fuse may result in fire and electric shock and equipment failure.
equipment failure.
Follow the instructions provided when installing
When connecting a DC power cord, be certain items sold separately and replacing the fuse.
the positive and negative polarities are correct. This may result in fire, electric shock and equip-
Reverse connection will result in equipment damage. ment failure.
Do not use DC power cords other than the
one enclosed or specified. Use only the provided or specified screws.
This may result in fire, electric shock and equip- Using screws of a different size, may result in
ment malfunctions. fire, electric shock and component damage.
CAUTION
Do not place the transceiver on an unsteady Do not use any products other than the speci-
or sloping surface, or in a location with ex- fied options and accessories.
treme vibration. Failure or miss operation may result.
The transceiver may fall or drop, resulting in fire, For safety reasons, switch off the power and
injury and equipment damage. pull out the DC power cord connected to the
Stay as far away from the antenna as possible DC power connector when the device is not
during transmission. going to be used for a long period of time.
Long-term exposure to electromagnetic radiation If not, this may result in fire and overheating.
may have a negative effect on the human body. Do not throw the transceiver, or subject it to
Do not wipe the case using thinner and ben- strong impact forces.
zene etc. Physical abuse may result in component damage
Use only a soft, dry cloth to wipe stains from the and equipment failure.
case. Keep magnetic cards and videotapes away
Keep this product out of the reach of children. from the transceiver.
Injury to the child, or damage to the transceiver The data recorded on cash cards or videotapes
may result. may be erased.
Do not put heavy objects on top of the power Do not stand on top of the product, and do not
cord and connection cables. place heavy objects on top or insert objects
This may damage the power cord and connection inside it.
cables, resulting in fire and electric shock. If not, this may result in equipment failure.
6
6 GETTING STARTED
6.1 ABOUT VHF RADIO
The radio frequencies used in the VHF marine band lie between 156 and 158
MHz with some shore stations available between 161 and 163 MHz. The marine
VHF band provides communications over distances that are essentially “line of
sight” (VHF signals do not travel well through objects such as buildings, hills or
trees). Actual transmission range depends much more on antenna type, gain and
height than on the power output of the transmitter. On a fixed mount 25 W radio
transmission expected distances can be greater than 25 km, for a portable 5 W
radio transmission the expected distance can be greater than 8 km in “line of sight”.
6.2 SELECTING AN ANTENNA

Marine antennas are made to radiate signals equally in all horizontal directions,
but not straight up. The objective of a marine antenna is to enhance the signal
toward the horizon. The degree to which this is accomplished is called the
antenna gain. It is measured in decibels (dB) and is one of the major factors
in choosing an antenna. In terms of effective radiated power (ERP), antennas
are rated on the basis of how much gain they have over a theoretical antenna
with zero gain. A 1 m, 3 dB gain antenna represents twice as much gain over
the imaginary antenna.
Typically, a 1 m 3 dB gain stainless steel whip is used on a sailboat mast. The
longer 2.5 m 6 dB fiberglass whip is primarily used on power boats that require
the additional gain.
3dB
6dB
9dB
6.3 COAXIAL CABLE

VHF antennas are connected to the transceiver by means of a coaxial cable
– a shielded transmission line. Coaxial cable is specified by its diameter and
construction.
For runs less than 20 feet (6 m), RG-58/U (about 0.25" (6 mm) in diameter),
is a good choice. For runs over 20 feet (6 m) but less than 50 feet (15 m), the
larger RG-8X or RG-213/U should be used. For cable runs over 50 feet (15 m)
RG-8X should be used. For installation of the connector onto the coaxial cable
refer to the figure.
7
To get the coax cable through a fitting and into the boat’s interior, you may
have to cut the end plug off and reattach it later. Follow the directions that
come with the connector to attach it. Be sure to make good soldered connec-
tions.
6.4 DISTRESS AND HAILING (CHANNEL 16)

Channel 16 is known as the Hail and Distress Channel. An emergency may be
defined as a threat to life or property. In such instances, be sure the transceiver
is ON and set to CHANNEL 16. Then use the following procedure:
1. Press the microphone push-to-talk switch and say “Mayday, Mayday,
Mayday. This is , , ” (your vessel’s name).
2. Then repeat once: “Mayday, ” (your vessel’s name).
3. Now report your position in latitude/longitude, or by giving a true or magnetic
bearing (state which) to a well-known landmark such as a navigation aid
or geographic feature such as an island or harbor entry.
4. Explain the nature of your distress (sinking, collision, aground, fire, heart
attack, life-threatening injury, etc.).
5. State the kind of assistance your desire (pumps, medical aid, etc.).
6. Report the number of persons aboard and condition of any injured.
7. Estimate the present seaworthiness and condition of your vessel.
8. Give your vessel’s description: length, design (power or sail), color and other
distinguishing marks. The total transmission should not exceed 1 minute.
9. End the message by saying “OVER”. Release the microphone switch and listen.
10. If there is no answer, repeat the above procedure. If there is still no response,
try another channel.
NOTE
The transceiver has the DSC Distress calling, that can transmit a distress
call digitally to all ships with compatible DSC radios. Refer to section “11
DIGITAL SELECTIVE CALLING (DSC)”.
8
6.5 CALLING ANOTHER VESSEL (CHANNEL 16 OR 9)
Channel 16 may be used for initial contact (hailing) with another vessel.
However, its most important use is for emergency messages. This channel
must be monitored at all times, except when actually using another channel.
It is monitored by the U.S. and Canadian Coast Guards and by other vessels.
Use of channel 16 for hailing must be limited to initial contact only. Call-
ing should not exceed 30 seconds, but may be repeated 3 times at 2-minute
intervals. In areas of heavy radio traffic, congestion on channel 16 resulting
from its use as a hailing channel can be reduced significantly in U.S. waters
by using channel 9 as the initial contact (hailing) channel for non-emergency
communications. Here, also, calling time should not exceed 30 seconds but
may be repeated 3 times at 2-minute intervals.
Prior to contacting with another vessel, refer to the channel charts in this manual,
and select an appropriate channel for communications after initial contact. For
example, Channels 68 and 69 of the U.S. VHF Charts are some of the chan-
nels available to non-commercial (recreational) boaters. Monitor the desired
channel in advance to make sure you will not be interrupting other traffic, and
then go back to either channel 16 or 9 to make initial contact.
When the hailing channel (16 or 9) is clear, press the PTT switch on the mic and
state the name of the other vessel you wish to call and then “this is” followed by
the name of your vessel and your Station License (Call Sign) then release the
PTT switch on the mic. When the other vessel returns your call, immediately
request another channel by pressing the PTT switch on the mic and saying “go
to,” the number of the other channel, say “over” and release the PTT switch on
the mic. Then switch to the new channel. When the new channel is not busy,
call the other vessel.
After a transmission, say “over,” and release the microphone’s push-to-talk
(PTT) switch. When all communication with the other vessel is completed, end
the last transmission by stating your Call Sign and the word “out.” Note that
it is not necessary to state your Call Sign with each transmission, only at the
beginning and end of the contact.
Remember to return to Channel 16 when not using another channel. Some
radios automatically monitor Channel 16 even when set to other channels or
when scanning.
9
6.6 WHAT IS THE RANGE FOR AIS RECEIVERS?
Since AIS uses similar frequencies as a marine VHF radio, it has similar radio
reception capabilities - which are basically line of sight. This means that the
higher the VHF antenna is mounted, the greater the reception area will be.
Reception from Class A vessels that are 20 or even 30 miles away on open
water is not uncommon as their antennas are mounted high off the water. Class
B transponders use lower power for transmissions; therefore, you can expect
Class B vessels to be acquired when they are 5 to 10 miles away.
NOTE
For additional information on AIS visit the USCG website:

<http://www.navcen.uscg.gov/marcomms/ais.htm>
6.7 Accuracy of COG

The error in the COG (the path of the antenna position over ground) due to the
actual ship’s speed over ground shall not exceed the following values:
Speed range (knots) Accuracy of COG output to user
0 to ≤1 knot Unreliable or not available
>1 to ≤17 knots ±3°
>17 knots ±1°
10
7 CONTROLS AND INDICATORS
This section defines each control of the transceiver. See illustration below
for location of controls. For detailed operating instructions refer to “9 BASIC
OPERATION” of this manual.
7.1 FRONT PANEL

⑨ ⑧⑦⑥⑤
①
⑩ ⑪ ⑫ ⑬ ⑭⑮
(Power) key
Press and hold to toggle the radio ON or OFF. When the power is turned
ON, the transceiver is set to the last selected channel.
DIAL/ENT knob
While the normal screen is displayed, rotate the DIAL/ENT knob to change
the operating channel. While the MENU screen is displayed, rotate the knob
to select the menu item.
Secondary use
 Press this knob to enter a selection in the MENU.
VOL knob (Volume control)
Adjusts the audio volume level.
Clockwise rotation of this knob increases the internal and speaker micro-
phone volume.
SQL knob (Squelch control)
Adjusting this control clockwise, sets the point at which random noise on
the channel does not activate the audio circuits but a received signal will
be heard. This point is called the squelch threshold. Further adjustment of
the squelch control will degrade reception of wanted transmissions.
11
H/L key
Press this key to toggle between 25 W (High) and 1 W (Low) power. When
the TX output power is set to “Low” while the transceiver is on channel 13 or
67 (USA Channel group only), the output power will temporarily switch from
“Low” to “High” power until the PTT switch of the microphone is released.
This key is not available on transmit inhibited and low power only channels.
MENU/SET key
Press to access MENU.
Press and hold to access SETUP MENU. For details, refer to section
“9.4 BASIC OPERATION OF THE SETUP MENU”.
CLEAR key
Press this key to cancel a menu selection.
GPS Antenna
Built in GPS antenna is located here.
BUSY Indicator LED
This indicator glows green when the squelch opens.
DATA jack
Use the USB micro type B jack to configure the transceiver settings and
download* the GPS logger data.
NOTE: When the DATA jack is securely covered with rubber cap, the GX2400 meets
the waterproofing performance.
DISTRESS key
Used to send a DSC Distress Call. To send the distress call, refer to section
“11.2.1 Transmitting a Distress Alert”.
/ ◄ & ► key
When the soft keys are displayed, press these keys to switch the function of soft keys.
Secondary use
While the MENU screen is displayed, press the key to slide the on-screen
menu to the right/left side.
Soft keys
Press these keys to display the soft keys.
The 3 programmable soft keys can be customized by the Setup Menu
described in section “16.8 SOFT KEYS”.
16/S key
Pressing this key immediately recalls channel 16 from any channel location.
Holding down this key selects the SUB channel (The default SUB channel
setting is channel 9). Pressing this key again reverts to the previous selected
working channel.
12
7.2 MICROPHONE
① ③
④
②
⑤
PTT (Push-To-Talk) switch

When in radio mode and the PTT switch is pressed, the transmitter is
enabled for voice communications to another vessel.
When an optional SSM-70H Microphone or SSM-72H Wireless Microphone
is connected and intercom mode is selected, pressing the PTT switch
enables voice communications from the transceiver to the SSM-70H Micro-
phone or the SSM-72H Wireless Microphone.
▲ & ▼ key
These keys on the microphone are used to select channels and to choose
menu items.
16/S key
Pressing this key immediately selects channel 16 from any channel location.
Holding down this key selects the Sub channel (The default SUB channel
setting is channel 9). Pressing this key again reverts to the previous selected
working channel.
H/L key
Press this key to toggle between 25 W (High) and 1 W (Low) power. When
the TX output power is set to “Low” and the transceiver is on channel 13 or
67 (USA Channel group only), the output power will temporarily switch from
“Low” to “High” power until the PTT switch of the microphone is released. High
power TX is not available on transmit inhibited and low power only channels.
13
Microphone
The internal microphone transmits your voice and reduces background
noise using Clear Voice Noise Reduction Technology.
When transmitting, position the microphone about 2 cm away from your
mouth. Speak slowly and clearly into the microphone.
Microphone speaker
Audio heard through internal radio speaker is heard through the speaker
microphone.
7.3 REAR PANEL

⑥⑦ ⑧ ⑨
③ ④ ⑤
VHF ANT Jack (VHF antenna jack)

Connects an antenna to the transceiver. Use a marine VHF antenna with
an impedance of 50 ohms.
GPS ANT Connector
Connects the optional SCU-38 External GPS Antenna.
NMEA 2K Connector
Connects to the NMEA 2000 network.
GND Terminal (Ground Terminal)
Connects the transceiver to ships ground, for safe and optimum performance.
Use the screw supplied with the transceiver only.
14
RAM Remote Access Microphone Connector
Connects the GX2400 to the SSM-70H (RAM4) Remote Station Microphone
or the SCU-30 Wireless Access Point for use with up to four SSM-72H
(RAM4X) wireless microphones. Refer to section “21 SSM-70H (RAM4)
REMOTE MIC OPERATION” for details.
EXTERNAL Speaker Connection Cable (White & Shield)
Connects the transceiver to an optional external speaker. See section
“3 OPTIONAL ACCESSORIES” for the available optional STANDARD
HORIZON accessories.
Speaker connections:
White: External Speaker (+)
Shield: External Speaker (−)
PA/HAIL Speaker Connection Cable (Red & Shield)
Connects the GX2400 to PA/HAIL speaker. See section “3 OPTIONAL
ACCESSORIES” for the available optional STANDARD HORIZON PA/
HAIL Speakers.
PA Speaker connections:
Red: PA Speaker (+)
Shield: PA Speaker (−)
DC Input Cable
Connects the transceiver to a DC power supply capable of delivering 11 to 16 VDC.
Accessory Connection Cable (Blue, Gray, White, Brown, Yellow, and Green)
Connects the transceiver to a GPS chart plotter. Refer to section “8.5.2
Accessory Cables”.
15
8 INSTALLATION
8.1 SAFETY / WARNING INFORMATION
Operation of this radio is restricted to occupational use, work related operations
only where the radio operator must have the knowledge to control the exposure
conditions of passengers and bystanders by maintaining the minimum separa-
tion distance of 3 feet (1 m). Failure to observe these restrictions will result in
exceeding the FCC RF exposure limits.
Antenna Installation:
The antenna must be located at least 3 feet (1 m) away from passengers in
order to comply with the FCC RF exposure requirements.
8.2 LOCATION
The radio can be mounted at any angle. Choose a mounting location that:
• complies with the compass safe distances shown in the table below to
prevent interference to a magnetic compass
Transceiver Unit 1.0 m
Handset 0.5 m
• provides accessibility to the front panel controls
• allows connection to a power source and antennas
• has nearby space for installation of a microphone hanger
• is at least 3 feet (1 m) away from the radio’s antenna
• the signals from the GPS satellites can be adequately received
NOTE: To insure the radio does not affect the compass or radio’s performance
is not affected by the antenna location, temporarily connect the radio in the
desired location and:
a. Examine the compass to see if the radio causes any deviation
b. Connect the antenna and key the radio. Check to ensure the radio is
operating correctly by requesting a radio check.
8.3 MOUNTING THE RADIO

8.3.1 Supplied Mounting Bracket
The supplied mounting bracket allows desktop mounting.
Use a 13/64" (5.2 mm) bit to drill the holes to a surface which is more 0.4 inch
(10 mm) thick and can support more than 3.3 lbs (1.5 kg) and secure the bracket
with the supplied screws, spring washers, flat washers, and nuts.
16
Desktop Mounting Overhead Mounting
8.3.2 Optional MMB-84 Flush Mount Bracket

A GPS receiver and antenna are located in the front panel of the GX2400. In
many cases the radio may be flush mounted, however before cutting holes to flush
mount the radio it is recommended to temporarily connect the radio to power and
turn it ON in the location where it will be flush mounted to confirm on the display
that it is able to receive a GPS location. If the radio is not able to receive a loca-
tion, a connection to a GPS Chart plotter with NMEA 0183 output, or the optional
SCU-38 External GPS Antenna may be needed to receive GPS satellite signals.
1. Use the template (page 143) to mark the location where the rectangular
hole is to be cut. Confirm the space behind the dash or panel is deep enough
to accommodate the transceiver (at least 6.2 inches (157 mm) deep).
There should be at least 1/2 inch (1.3 cm) between the transceiver’s heat-
sink and any wiring, cables or structures.
2. Cut out the rectangular hole and insert the transceiver.
3. Fasten the brackets to the rear panel of the transceiver (see illustration).
4. Turn the adjusting screw to adjust the tension so that the transceiver is tight
against the mounting surface.
17
8.4 ELECTRICAL CONNECTIONS
CAUTION
Reverse polarity battery connections will damage the radio!
Connect the power cord and antenna to the radio. Antenna and Power Supply
connections are as follows:
1. Mount the antenna at least 3.28 feet (1 m) away from the radio. At the rear
of the radio, connect the antenna cable. The antenna cable must have
a PL259 connector attached. RG-8/U coaxial cable must be used if the
antenna is 25 feet (7.6 m) or more from the radio. RG58 cable can be used
for distances less than 25 feet (7.6 m).
2. Connect the red power wire to a 13.8 VDC ±20% power source. Connect
the black power wire to a negative ground.
3. If an optional external speaker is to be used, refer to section 8.5 for connections.
4. It is advisable to have a Certified Marine Technician check the power output
and the standing wave ratio of the antenna after installation.
GPS Navigation Receiver Optional MLS-300
External Speaker Optional MLS-300 Optional SSM-70H
External Speaker (RAM4) Remote MIC
Optional SCU-38
External GPS Antenna
Antenna
Water proof
Deck Outlet
Ac
ces
sor
yC
ab
sle
Fuse
Red Black
Ensure that the SCU-38, the
MLS-300 and the SSM-70H are
located at a distance that does not
Power Source
affect the magnetic compass.
Fuse Replacement
To remove the fuse from the fuse holder, hold both
ends of the fuse holder and pull the fuse holder apart
without bending the fuse holder. When replacing the
fuse, confirm that the fuse is tightly fixed into the metal
contact located inside the fuse holder. If the metal
contact holding the fuse is loose, the fuse holder may
heat up.
18
8.5 CONNECTION OF EXTERNAL DEVICES TO THE RADIO
8.5.1 Connecting the NMEA 0183/NMEA 0183-HS to the Radio
External GPS Device Connections (NMEA 0183 4800 baud or NMEA 0183-HS 38400 baud)
The GX2400 can select the NMEA baud rate between “4800 bps” and “38400
bps”. Refer to section “19.9 NMEA 0183 IN/OUT” for selection.
NMEA Input (GPS Information)
• The transceiver can read NMEA 0183 version 2.0 or higher, and NMEA
0183-HS version 1.01 or higher.
• The NMEA 0183 input sentences are GLL, GGA, RMC, GNS, GSA, and
GSV (RMC sentence is recommended).
• If 4800 baud (default) is selected:
The Yellow and Green input wires are at 4800 baud.
• If 38400 baud is selected:
The Yellow and Green input wires are at 38400 baud.
NMEA Output (DSC and GPS information)
• The NMEA 0183 output sentences are DSC and DSE.
• If 4800 baud (default) is selected:
The White and Brown wires output DSC and DSE sentences.
• If 38400 baud is selected:
The Blue and Gray output wires are at 38400 baud and include
DSC (DSC, DSE) sentences.
• GSA, GSV, GLL, GGA, and RMC sentences can be output from the trans-
ceiver using settings in the GPS setup menu (refer to section “19.9 NMEA
0183 IN/OUT”).
For further information on interfacing and setting up GPS operation, contact
the manufacturer of the externally connected GPS receiver.
If you have further questions, please contact your Dealer.
8.5.2 Accessory Cables
The image and table below show the wires of the transceiver and the connec-
tions to optional devices such as an external GPS antenna and a GPS chart
plotter.
CAUTION
Care must be taken not to touch any of the NMEA wires to positive 12 VDC
or the radio may be damaged.
When connecting the Chart Plotter, External GPS receiver, or External Speaker
strip off about 1 inch (2.5 cm) of the specified wire’s insulation, then splice the
ends together.
The transceiver uses NMEA 0183/-HS protocol to share coordinates and DSC
information to and from a GPS chart plotter.
19
8.5.3 Internal GPS (DSC Output) to Chart Plotter
Radio Wires Plotter Connection GPS Chart Plotter
Yellow: NMEA IN (+) No Connection
Green: NMEA IN (−) No Connection
White: NMEA OUT (+) NMEA IN (+)
Brown: NMEA OUT (−) NMEA IN (−)
Blue: NMEA-HS OUT (+) NMEA-HS IN (+)
Gray: NMEA-HS OUT (−) NMEA-HS IN (−)
Wire Color/Description Connection Examples

YELLOW - NMEA GPS Input (+) No connection
GREEN - NMEA GPS Input (−) No connection
WHITE - NMEA DSC Output (+) NMEA (+) input of GPS*1
BROWN - NMEA DSC Output (−) NMEA (−) input of GPS*1
BLUE - AIS Data Output (+) NMEA-HS (+) input of AIS receiver*2
GRAY - AIS Data Output (−) NMEA-HS (−) input of AIS receiver*2
*1: 4800 baud, *2: 38400 baud
NOTE: Some GPS chart plotters have a single wire for NMEA signal ground. In this case,
connect the NMEA input (−) to the GPS chart plotter’s single NMEA signal ground wire, and
leave the NMEA output (−) open. In case the assignment of power supply and ground of a
GPS chart plotter to be used is different from that of the radio, connect the signal ground
wire of the GPS chart plotter to the ground terminal (GND) on the rear panel of the radio.
8.5.4 Connection to External GPS or Chart Plotter
Radio Wires Plotter Connection GPS Receiver
Yellow: NMEA IN (+) NMEA OUT (+)
Green: NMEA IN (−) NMEA OUT (−)
White: NMEA OUT (+) NMEA IN (+)
Brown: NMEA OUT (−) NMEA IN (−)
Blue: NMEA-HS OUT (+) NMEA-HS IN (+)
Gray: NMEA-HS OUT (−) NMEA-HS IN (−)

YELLOW - NMEA GPS Input (+) NMEA (+) output of GPS*1
GREEN - NMEA GPS Input (−) NMEA (−) output or common ground of GPS*1
WHITE - NMEA DSC Output (+) NMEA (+) input of GPS*1
BROWN - NMEA DSC Output (−) NMEA (−) input of GPS*1
BLUE - AIS Data Output (+) NMEA-HS (+) input of AIS receiver*2
GRAY - AIS Data Output (−) NMEA-HS (−) input of AIS receiver*2
*1: 4800 baud ,*2: 38400 baud
NOTE: To input the GPS coordinates from an external GPS device to the transceiver,
the NMEA GPS input (+) (yellow) and the NMEA GPS input (-) (green) wires may be
connected to the NMEA output of the external GPS antenna or GPS chart plotter.
To connect with an external device at 38400 baud
To connect with an external device at 38400 baud, the transceiver may be setup
to receive GPS coordinates and send DSC signals at 38400 baud. Refer to
section “19.9 NMEA 0183 IN/OUT” for details.
20
8.5.5 Connection to External PA/HAIL Speaker
White
External Speaker
Shield
Red
PA Speaker (horn)
Shield

White - External Speaker (+) Positive wire of external 4 Ohm External speaker
Shield - External Speaker (−) Negative wire of external 4 Ohm External speaker
Red - PA Speaker (+) Positive wire of external 4 Ohm audio speaker (horn)
Shield - PA Speaker (−) Negative wire of external 4 Ohm audio speaker (horn)
8.5.6 Connecting optional SCU-38 External GPS Antenna

Connect the SCU-38 cable to the coaxial
GPS ANT connector on the rear panel,
then tighten the cable nut (see illustration
at the right).
NOTE: The SCU-38 is always more preferred
than the internal GPS antenna.
8.5.7 Connecting optional SCU-31 External GPS Antenna

External GPS Antenna
SCU-31
Radio Wires
Yellow: NMEA IN(+) Brown
Green: NMEA IN(−) Black

Black Red
2A Fuse
(−) (+)
12 V Battery
NOTE
To connect optional SCU-31, the transceiver may be setup to receive GPS coor-
dinates at 4800 baud. Refer to section “19.9 NMEA 0183 IN/OUT” for details.
The SCU-31 External GPS Antenna (Built-in GPS receiver) is supplied with
49 feet (15 m) of cable and a connector. To connect the SCU-31 to the trans-
ceiver, cut off the 6 pin antenna connector, strip the white insulation to expose
the Red, Black and Brown wires and connect as shown in the diagram. All
other wires are not used and may be cut off. The 2 amp fuse is not included.
21
8.5.8 Optional SSM-70H (RAM4) Microphone
NOTE
To connect the GX2400, the SSM-70H firmware must be Ver. 3.00.00 or later.
The transceiver is capable of using an SSM-70H (RAM4) Remote Station Micro-

phone to control all the Radio functions. In addition, the transceiver can operate as a
full function intercom system between the SSM-70H microphone and the transceiver.
WARNING
Do not connect or remove the SSM-70H (RAM4) microphone while the
radio is powered ON. This may result in equipment failure.
1. Connect the Routing Cable (supplied with the SSM-70H) to the RAM
connector (eight pins) on the rear panel, then tighten the cable nut (see
the below illustration).
2. Install the two ferrite cores (supplied with the SSM-70H Remote Station
Microphone) to the routing cable or the CT-100 extension cable, then snap
the halves together. These cores should be installed near the connectors
of the transceiver and the microphone ends of the cable.
3. Attach the ferrite cores as close as possible to the plugs, as shown below.
External Speaker
Connections
Ferrite Core Ferrite Core
｛
to SSM-70H
to Transceiver
(RAM4)
Routing Cable or
CT-100 Extension Cable
As close as possible As close as possible
CAUTION
Before cutting the cable, it must be disconnected from the rear panel of the transceiver.
The routing cable can be cut and spliced, however care needs to be taken when
reconnecting the wires to ensure water integrity.
After cutting you will notice there are the following wires:
Yellow, Green, White, Brown and Red/Shield
22
4. Finally, wind some plastic tape
around each ferrite core, to
prevent vibration from causing
the two halves to split apart.
5. Referring to the illustration at the
right, make a 30 mm hole in the
wall, then insert the extension
cable into this hole. Connect the External Speaker Connections
gasket and mount base to the Ferrite Core
Gasket
extension cable connector using Cap
the nut.
6. Drill the four screw holes (approx.
Wall
2 mm) into the wall, then install the
mounting base to the wall using Routing Cable
four screws.
Mounting Bracket Nut
7. Put the rubber cap onto the nut.
The installation is now complete.
WARNING
It is not recommended to plug or unplug the SSM-70H (RAM4) Remote
Station Microphone into the routing cable while the radio is powered ON.
Connecting an External Speaker to the RAM4 Mic Cable

In noisy locations and the MLS-300 optional external speaker may be connected
to the white speaker wires on the RAM4 routing cable. The RAM4 can drive
either the internal speaker or the external speaker one at a time. When connect-
ing an external speaker, follow the procedure below to turn the RAM4 audio OFF
and enable the external speaker connected to the RAM4 routing cable wires.
1. On the RAM4 microphone, press and hold the [MENU/

SET] key.
2. Rotate the DIAL/ENT knob to select “CONFIGURA-
TION”, then press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select “SPEAKER
SELECT”, then press the [SELECT].
4. Rotate the DIAL/ENT knob to select “INTERNAL” or

“EXTERNAL”, then press the [SELECT] soft key.
5. Press the [CLEAR] key to return to radio operation.
23
8.5.9 Optional SCU-30 Wireless Access Point Installation
NOTE
To connect the SSM-72H (RAM4X), the SCU-30 firmware must be Ver.

2.00.00 or later.
The GX2400 is capable of using a SSM-72H (RAM4X) Wireless Remote Station

Microphone to remotely control the Radio, AIS, DSC and PA/Fog functions. In
addition the GX2400 can operate as a full function intercom system between
the RAM4X and the GX2400.
The optional SCU-30 Wireless Access Point, may be utilized to connect up to
four RAM4X Wireless Remote Access Microphones to the GX2400.
WARNING
Do not connect or remove the SCU-30 Wireless Access Point while the
radio is powered ON. This could result in damage to the equipment.
1. Connect the SCU-30 Cable to the RAM Connector on the GX2400 rear
panel, and tighten the cable nut.
NOTE: For additional details on the connecting the RAM4X and GX2400, refer to
the RAM4X Instruction Manual.
8.6 INITIAL SETUP REQUIRED WHEN TURNING ON THE

POWER FOR THE FIRST TIME
8.6.1 Maritime Mobile Service Identity (MMSI)
What is an MMSI?
An MMSI is a nine-digit number used on marine transceivers capable of using
Digital Selective Calling (DSC) signal transmission. This number is used like
a telephone number to selectively call other vessels.
THIS NUMBER MUST BE PROGRAMMED INTO THE RADIO TO OPERATE
DSC FUNCTIONS.
How can I obtain an MMSI assignment?
Contact the Radio Licensing Authority for your country for information on obtaining an
MMSI number.
24
WARNING
The MMSI can be input only once, be careful not to input the incorrect
MMSI number. If the MMSI number needs to be reset, contact Standard
Horizon to obtain the required reset code. Refer to section “16.9.1 Reset
the USER MMSI and ATIS CODE”.
Programming the MMSI

1. Press the [MENU/SET] key to display “MENU”.
2. Rotate the DIAL/ENT knob to select “MMSI/POS
INFO”, then press the [SELECT] soft key. (To cancel,
press the [BACK] soft key.)
3. The “MMSI INPUT” screen is displayed if the MMSI
has not yet been input.
When the transceiver entry has been completed, it is
only possible to check the MMSI on this screen.
*********
4. Press the [◄] or [►] key to select the first number of

your MMSI, then press the [SELECT] soft key to step
to the next number.
5. Repeat step 4 to set your MMSI number (9 digits).
If a mistake is made entering in the MMSI number,
press the [◄] or [►] key to select “←” or “→”, press
the [SELECT] soft key until the incorrect character is
selected, then perform step 4.
6. When finished programming the MMSI number, press
the [FINISH] soft key. The radio will ask you to input
the MMSI number again. Perform steps 4 through 6
above.
7. After the second number has been input, press the
[FINISH] soft key to store the MMSI. *********
8. Press the [OK] soft key to return to radio operation.
NOTE
To check the MMSI after programming to ensure it is correct, perform steps
1 to 2. The current MMSI number is shown on the display.
25
8.7 CONFIRMING GPS SIGNAL (GPS STATUS DISPLAY)
When the GX2400 receives the GPS signal from the internal GPS receiver ,
a small satellite icon “ ”* will appear on the display and your current location
(latitude/longitude) is shown on the display. (*When the GPS signal receiving
from the NMEA 2000 or NEMA-0183, a “2K” (NMEA 2000) icon or “I/O” (NMEA-
0183) icon will appear on the display.)
If there is a problem with the NMEA connection between the radio and the GPS,
the GPS icon will blink continuously until the connection is corrected.
The transceiver has a GPS status display which shows
the satellites currently being received, along with a
graphical (bar-graph) representation of the relative
signal strengths from the satellites. (GPS Status Display mode)
NOTE
When the GPS reception is limited, such as the flush mounting of the radio,
it is recommended to connect the optional External GPS Antenna SCU-38
to the GPS connector on the rear panel.
1. Press the [MENU/SET] key to display “MENU”.

2. Rotate the DIAL/ENT knob to select “GPS”, then press
the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select “GPS STATUS”,
then press the [ENTER] soft key to display the GPS
status currently being received.
NOTE
For the transceiver to properly show the GPS status page when an exter-
nal GPS receiver or a chart plotter is connected, the external device must
be setup to output GSA and GSV NMEA 0183 sentences. When using
the equipment of NMEA 2000, it must be able to output PGN No.129540
(GNSS Sats in View).
26
8.8 GPS CONFIGURATION
8.8.1 Setting the GPS Time
The transceiver shows GPS satellite time or UTC (Universal Time Coordinated)
time in factory default. A time offset is needed to show the local time in your
area. The time offset must be changed in order for the radio to display the
current time in your area.
1. Press and hold the [MENU/SET] key.
2. Rotate the DIAL/ENT knob to select “GPS SETUP”,
then press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select “TIME OFFSET”,

4. Rotate the DIAL/ENT knob to select time offset of

your location. If “00:00” is assigned, the time is the
same as UTC or GPS satellite time.
5. Press the [ENTER] soft key to store the time offset.
8.8.2 Setting the Time Area
This menu selection allows the transceiver to show UTC time or local time
with the offset.
3. Rotate the DIAL/ENT knob to select “TIME AREA”,

4. Rotate the DIAL/ENT knob to select “UTC” or

“LOCAL”.
5. Press the [ENTER] soft key to store the selected
setting.
27
8.8.3 Setting the Time Format
This menu selection allows the transceiver to be setup to show time in 12-hour
or 24-hour format.
3. Rotate the DIAL/ENT knob to select “TIME FORMAT”,

4. Rotate the DIAL/ENT knob to select “24hour” or

“12hour”.
setting.
8.8.4 Setting COG to True or Magnetic

The GPS COG (Course Over Ground) and the BRG from a Waypoint Target
magnetic variation may be selected to show in ON or OFF. Factory default is
“OFF” however by following the steps below the COG can be changed to “ON”.
3. Rotate the DIAL/ENT knob to select “MAGNETIC

VARIATION”, then press the [SELECT] soft key.
4. Rotate the DIAL/ENT knob to select “OFF” or “ON”.

setting.
NOTE
The “ON” setting is effective only when the RMC sentences with magnetic
data are input from external devices such as a GPS Chart Plotter.
28
9 BASIC OPERATION
9.1 TURNING THE TRANSCEIVER ON AND OFF
1. After the transceiver has been installed, ensure that the power supply and
antenna are properly connected.
2. Press and hold the key to turn the radio ON.
3. Press and hold the key again to turn the radio OFF.
9.2 RECEPTION
1. Rotate the SQL knob fully counterclockwise. This state is known as “squelch off”.
2. Turn up the VOL knob until noise or audio from the speaker is at a comfort-
able level.
3. Rotate the SQL knob, clockwise until the random noise disappears. This
state is known as the “squelch threshold”.
4. Rotate the DIAL/ENT knob to select the desired
channel. Refer to the channel chart on page 131
for available channels.
5. When a signal is received, adjust the volume to the
desired listening level. The BUSY Indicator Lamp
glows green, and the “BUSY” indicator on the display
indicates that communications are being received.
9.3 TRANSMISSION
1. Perform steps 1 through 4 of RECEPTION.
2. Before transmitting, monitor the channel to ensure it is clear.
THIS IS AN FCC REQUIREMENT!
3. Press the microphone’s PTT (push-to-talk) switch.
The “TX” indicator on the LCD is displayed.
4. Speak slowly and clearly into the microphone.
5. When the transmission is finished, release the micro-
phone PTT switch.
NOTE
Position your mouth about 2 cm away from the microphone and speak in a
normal voice.
29
9.3.1 Transmit Power
The TX output power of the transceiver is set to high (25 W) in factory default,
and the “HI” indicator is displayed on the top part of the screen.
To switch the TX output power:
1. Press the [H/L] key on the front panel or the micro-
phone to switch between HI (25 W) or LO (1 W) output
power.
NOTE: When the TX output power is set to “Low” while the
transceiver is on channel 13 or 67 (USA Channel group
only), the output power will temporarily switch from “Low”
to “High” power until the PTT switch of the microphone is
released. This soft key is not function on transmit inhibited
and low power only channels.
9.4 BASIC OPERATION OF THE SETUP MENU

Using the setup menu, the various functions of the transceiver can be custom-
ized to match the user’s needs and preferences. Items to be adjusted
may be selected from the respective lists and the appropriate settings made
for the various intended operations.
1. Press and hold the [MENU/SET] key on the operation
mode screen.
2. Rotate the DIAL/ENT knob to select the function item,
3. Rotate the DIAL/ENT knob to select the setting item,

setting.
setting.
(The display can also be returned to the previous
screen by pressing the [BACK] soft key.)
The above process is used when making the Setup Menu adjustments that
follow in this Operating Manual.
Press & hold [ ]  “DSC SETUP”  “INDIVIDUAL DIRECTORY”
30
9.5 TRANSMIT TIME-OUT TIMER (TOT)
When the PTT switch on the microphone is held down, transmit time is limited
to 5 minutes. This limits unintentional transmissions due to a stuck microphone.
About 10 seconds before automatic transmitter shutdown, a warning beep will
be heard from the speaker(s). The transceiver will automatically go to receive
mode, even if the PTT switch is continually held down. Before transmitting
again, the PTT switch must first be released and then pressed again.
NOTE
Once the transmitter is shut down by the TOT, transmission on the channel
is only allowed 10 seconds after the shutdown.
9.6 SIMPLEX/DUPLEX CHANNEL USE

Refer to the VHF MARINE CHANNEL CHART (Page 131) for instructions on
use of simplex and duplex channels.
NOTE
All channels are factory-programmed in accordance with FCC (USA), ISED

(Canada), and International and region regulations. Mode of operation cannot
be altered from simplex to duplex or vice-versa.
9.7 CHANNEL GROUP

Set the Channel Group according to the region:
1. Press & hold [ ]  “CHANNEL SETUP”  “CHANNEL GROUP”
2. Rotate the DIAL/ENT knob to select the desired chan-

nel group “USA”, “INTL”, or “CAN”*1.
*1In the European version, when setting the region, the
selected European Channel Group will be displayed
instead of “CAN” group. For details, refer to the “Note
on the Setting the Region” on the separate yellow
insert sheet.
3. Press the [ENTER] soft key to store the selected setting.
Refer to the “24 CHANNEL ASSIGNMENTS” (page 131) for allocated chan-
nels in each mode.
31
9.8 NOAA WEATHER CHANNELS (in USA and Canada only)
1. To receive a NOAA weather channel, press one of the
soft keys, then press the [◄] or [►] key repeatedly
until the [WX] soft key is displayed at the bottom of
the screen.
2. Press the [WX] soft key.
The “WX” indicator appears on the top part of the screen.
NOTE: To receive a NOAA weather channel, assign the “WX” command into one
of the soft keys, refer to section “16.8 SOFT KEYS”.
3. Rotate the DIAL/ENT knob to select a different NOAA
weather channel.
4. To exit from the NOAA weather channels, press one
of the soft keys, then press the [CH] soft key. The
transceiver returns to the channel it was on prior to a
weather channel and the “WX” indicator disappears
from the display.
9.8.1 NOAA Weather Alert (USA version only)
In the event of extreme weather disturbances, such as storms and hurricanes,
the NOAA (National Oceanic and Atmospheric Administration) sends a weather
alert accompanied by a 1050 Hz tone and transmits a subsequent weather
report on one of the NOAA weather channels.
The GX2400GPS can receive weather alerts when monitoring a weather chan-
nel and on the last selected weather channel during scanning modes or while
monitoring a working channel.
To enable the weather alert function, refer to section “17.2 WEATHER ALERT
(USA version only)”.
When an alert is received on a NOAA weather channel,
scanning will stop and the transceiver will emit a loud
beep to alert the user of a NOAA broadcast. Press any
key to stop the alert. After stopping the beep sound, the
weather alert reception confirmation screen will appear. Press [OK] to display
a confirmation screen. The confirmation screen will ask you whether to move
to the weather channel or return in the marine channel. Press [YES] to switch
to the weather channel, and press [NO] to return to the marine channel.
NOTE
If no key is pressed the alert will sound for 5 minutes and then the weather
report will be received.
32
9.8.2 NOAA Weather Alert Testing
NOAA tests the alert system every Wednesday between 11AM and 1PM.
To test the NOAA weather feature, setup the transceiver as in section “9.8.1
NOAA Weather Alert (USA version only)” and confirm the alert is heard on
Wednesdays between 11AM and 1PM local time.
9.9 MULTI WATCH (TO PRIORITY CHANNEL)

Multi watch is used to scan two or three channels for communications.
• In Dual Watch, a normal VHF channel and the priority channel are scanned
alternately.
• In Triple Watch, a normal VHF channel, the priority channel, and the sub
channel are scanned alternately.
When a signal is received on the normal channel the radio briefly switches
between the normal channel and the priority channel to look for a transmission.
If the radio receives communications on the priority channel the radio stops
and listens to priority channel until communication ends and then starts dual
or triple watch scan again.
9.9.1 Setup the Multi Watch Operation
1. Press & hold [ ]  “CHANNEL SETUP”  “MULTI WATCH”
2. Rotate the DIAL/ENT knob to select “DUAL” or

“TRIPLE”.
9.9.2 Starting Dual Watch
1. Adjust the SQL knob until the background noise disappears.
2. Rotate the DIAL/ENT knob to select a channel you wish to watch.
3. Press one of the soft keys.
4. Press [◄] or [►] key repeatedly until the [DUAL
WATCH] soft key is displayed at the bottom of the
screen, press the [DUAL WATCH] soft key.
The radio will monitor the priority channel and the channel that was selected in step 2.
If a signal is received on the channel selected in step 2, the transceiver will
dual watch to priority channel.
5. To stop dual watch, press the [DUAL WATCH] soft key again.
When selecting “TRIPLE” in the SETUP menu, [TRI WATCH] will be displayed
as the soft key instead of [DUAL WATCH].
33
NOTE
The priority channel or the sub channel may be changed from CH16 (default)
or CH9 (default) to another channel. Refer to section “17.7 PRIORITY CHAN-
NEL” or “17.8 SUB CHANNEL”.
9.10 SCANNING
The transceiver will automatically scan channels programmed into the preset
channel memory and also the scan channel memory, and the last selected
weather channel.
When an incoming signal is detected on one of the channels during scan, the radio
will pause on that channel, allowing you to listen to the incoming transmission.
The radio will automatically start scanning again after the transmission stops.
9.10.1 Selecting Scan Type
1. Press & hold [ ]  “CHANNEL SETUP”  “SCAN TYPE”
2. Rotate the DIAL/ENT knob to select “PRIORITY” or

“MEMORY”.
setting.
CH1001 CH1001
CH88 CH09 CH88 CH09
CH1078 CH12 CH1078 CH12
Priority Channel
CH68 CH15 CH68 CH15
CH1061 CH1018 CH1061 CH1018

CH1022 CH1022
Memory Scan (M-SCAN) Priority Scan (P-SCAN)
9.10.2 Programming Scan Memory
1. Press & hold [ ]  “CHANNEL SETUP”  “SCAN MEMORY”
2. Rotate the DIAL/ENT knob to select a desired channel

to be scanned, then press the [MEM] soft key. The
“ON” icon will appear at the right side of the selected
channel.
3. Repeat step 2 for all the desired channels to be scanned.
34
4. To REMOVE a channel from the list, select the channel then press the
[MEM] soft key. The “ON” icon of the selected channel will disappear.
5. When you have completed your selection, press the [CLEAR] key to return
to radio operation.
To check the channels to be scanned, rotate the DIAL.
ENT knob. The “MEM” icon will appear when the memory
channel is displayed.
NOTE: When “SCAN MEMORY” is assigned to the soft key, the
memory function switches between ON and OFF each time the
[MEM] soft key is pressed.
9.10.3 Memory Scanning (M-SCAN)

1. Set the scan type to “MEMORY” in the SETUP menu (refer to “9.10.1
Selecting Scan Type”).
4. Press the [◄] or [►] key repeatedly, then press the
[SCAN] soft key. The “MEM SCAN” icon appears on
the display. Scanning will proceed from the lowest
to the highest programmed channel number and the
preset channel (described in the next section). Scan-
ning will stop on a channel when a transmission is
received.
The channel number will blink during reception.
5. To stop scanning, press the [SCAN] soft key, [16/S] or [CLEAR] key.
9.10.4 Priority Scanning (P-SCAN)

1. Set the scan type to “PRIORITY” in the SETUP menu (refer to “9.10.1
Selecting Scan Type”).
[SCAN] soft key. The “PRI SCAN” icon appears
on the display. Scanning will proceed between the
memorized channels, the preset channel (described
in next section) and the priority channel.
The priority channel will be scanned after each programmed channel.
5. To stop scanning, press the [SCAN] soft key, [16/S] or [CLEAR] key.
35
NOTE
In the default setting, Channel 16 is set as the priority channel. You may
change the priority channel from Channel 16 to another desired channel using
the SETUP menu. Refer to section “17.7 PRIORITY CHANNEL”.
9.11 PRESET CHANNELS: INSTANT ACCESS

10 preset channels can be programmed for instant access. Pressing the
[PRESET] soft key activates the user assigned channel bank. If the [PRESET]
soft key is pressed and no channels have been assigned, an error beep will
sound.
Before beginning the Instant Access operation, assign the “PRESET” command
into one of the programmable keys, refer to section “16.8 SOFT KEYS”.
9.11.1 Programming
1. Rotate the DIAL/ENT knob to select the channel to
be programmed.
3. Press the [◄] or [►] key repeatedly, until the
[PRESET] soft key is displayed, then press and hold
the [PRESET] soft key until the “P-SET” icon and
channel number are blinking.
4. Press the [ADD] soft key to program the channel into
the preset channel memory. The “P-SET” icon will
appear.
5. Repeat steps 1 through 3 to program the desired
channels into the preset channels. Up to 10 channels
can be registered. If you attempt to register the 11th
channel, an error beep will sound.
9.11.2 Operation
[PRESET] soft key to recall the preset channel. The
“P-SET” icon will appear on the display.
3. Rotate the DIAL/ENT knob to select the desired preset
channel.
4. Press the [PRESET] soft key to return to the last
selected channel. The “P-SET” icon will disappear
from the display.
36
9.11.3 Deletion
[P-SET] soft key to recall the preset channel
3. Rotate the DIAL/ENT knob to select the preset chan-

nel to be deleted.
4. Press one of the soft keys, then press and hold the
[PRESET] soft key until the “P-SET” icon and channel
number are blinking.
5. Press the [DELETE] soft key to delete the channel

from the preset channel memory.
6. Repeat steps 3 through 5 to delete the undesired
channels from preset channels.
7. To exit from deleting the preset channels, press the [QUIT] soft key.
9.12 MOB OPERATION

The GX2400 provides a feature to memorize the position information instantly
in case of MOB (Man Over-Board).
[MOB] soft key.
3. Press the [TO WPT] soft key to start the navigation to
the displayed position. For details about the naviga-
tion, see section “12 NAVIGATION”.
To change the displayed position information, press the
[POS/TM] soft key. For details about modification of the
position, see “Editing a Waypoint” on page 78.
4. To transmit a DSC distress message, lift the red
spring loaded DISTRESS cover on the right side of
the transceiver, then press and hold the DISTRESS
key (see section “11.2.1 Transmitting a Distress
Alert” for details).
37
9.13 PA/FOG OPERATION
The GX2400 has 30 W hailer built-in and can be used with any 4 Ohm PA horn.
Standard Horizon offers two HAIL/PA horns, the 220SW (5” round 30 Watt
HAIL/PA horn) and the 240SW (5” x 8” rectangular 40 Watt HAIL/PA horn).
When the GX2400 is in PA Hail mode the PA speaker listens back (acts as a
microphone and provides two-way communications through the HAIL/PA horn
to the main radio).
NOTE
When in the PA HAIL or FOG HORN mode, the GX2400 will continue to
receive DSC calls and communications on the last selected working channel
prior to entering the PA HAIL or FOG HORN mode.
Then the GX2400 AIS page can also be accessed when in the PA HAIL or
FOG HORN mode.
PA HAIL mode:
PA HAIL mode allows the transceiver to be used as a power hailer when
an optional STANDARD HORIZON 220SW or 240SW HAIL/PA horn is
installed. The PA Hail mode has a listen-back feature which provides two
way communication through the HAIL/PA horn.
FOG HORN mode:
Automatic signaling is transmitted through the HAIL/PA horn. When the
fog horn signal is not being outputted the GX2400 listens back through the
connected HAIL/PA horn.
HORN mode:
Foghorn sound or siren sound can be transmitted through the HAIL/PA
horn. When the fog horn signal is not being outputted the GX2400 listens
back through the connected HAIL/PA horn.
9.13.1 Operating the PA HAIL mode
2. Press the [◄] or [►] key repeatedly, then press the [PA] soft key.
3. Press the microphone’s PTT switch to speak through
the HAIL/PA speaker.
4. Press the [PA VOL] soft key, then rotate the DIAL/
ENT knob to control the AF output level.
Press the [ENTER] soft key. The AF output level can
be set from 0 to 31.
5. To listen back, rotate the VOL knob.
38
9.13.2 Operating the FOG HORN mode
The user can select the type of horn from “Underway”, “Stop”, “Sail”, “Towing”,
“Aground”, “Anchor”, “Horn”, and “Siren”.
2. Press the [◄] or [►] key repeatedly, then press the [FOG HORN] soft key.
3. Rotate the DIAL/ENT knob to select one of the eight
functions described above, then press the [SELECT]
soft key.
4. Press the [FOG VOL] soft key, then rotate the DIAL/
5. On the “HORN" and "SIREN” modes, press the
[HORN] soft key to activate the tone through the HAIL/
PA speaker.
Press the [HORN VOL] soft key, then rotate the DIAL/
5. To listen back, rotate the VOL knob.
9.13.3 Fog Signal Timing Chart
TYPE PATTERN USAGE
UNDERWAY One 5-second blasts 5s 5s Motor vessel underway and
every 120 seconds. making way.
Listen Back
120s
STOP Two 5-second blasts 5s 5s 5s 5s Motor vessel underway but

(separated by 2 stopped (not making way).
seconds) every 120 Listen Back
seconds. 2s 2s
120s
SAIL One 5-second 5s 1s 1s 5s 1s 1s Sailing vessel underway,

blasts followed by fishing vessel (underway or
two 1-second blasts Listen Back anchored), vessel not under
(separated by 2 2s 2s 2s 2s command, a vessel restricted
120s
seconds) every 120 in her ability to maneuver
seconds. (underway or at anchor), or
a vessel towing or pushing
another ahead.
TOWING One 5-second blasts 5s 1s 1s 1s 5s 1s 1s 1s Vessel under tow (manned).
followed by three
1-second blasts Listen Back
(separated by 2 2s 2s 2s 2s 2s 2s
120s
seconds) every 120
seconds.
39
TYPE PATTERN USAGE
AGROUND One 11-second rings 1s 1s 1s 5s 1s 1s 1s Vessel is aground.
every 60 seconds. 250ms
11s
Listen Back
60s
ANCHOR One 5-second rings 5s Vessel is at anchor.
every 60 seconds. 250ms
5.25s
Listen Back
60s
9.14 INTERCOM OPERATION

The optional SSM-70H (RAM4) or SSM-72H (RAM4X) remote station micro-
phone must be connected to perform intercom functions between the GX2400
and the SSM-70H (RAM4) or SSM-72H (RAM4X).
NOTE
When using the intercom function, connect SSM-70H (RAM4) or SSM-72H

(RAM4X) Remote Station Microphone to the transceiver.
9.14.1 Communication
[IC] soft key.
3. Rotate the DIAL/ENT knob to select the device to
which you want to communicate, then press the
[SELECT] soft key. The “” icon will appear at the
left side of the selected station.
NOTE: When only one SSM-70H (RAM4) or SSM-72H
(RAM4X) is connected to GX2400, continue to step 6.
4. Repeat step 3 for all the desired devices.
5. Press the [ENTER] soft key.
6. When the intercom mode is enabled, “INTERCOM”
is displayed on the radio and SSM-70H (RAM4).
40
4. Press the transceiver microphone PTT switch, “Talk”
will be shown on the display.
NOTE: A warning beep will be heard when the transceiver
PTT and RAM4 PTT switches are pushed at the same time.
5. Speak slowly and clearly into the microphone, hold the microphone about
1.5 cm away from your mouth.
6. When finished, release the PTT switch.
9.14.2 Calling
When in intercom mode, pressing the [BELL] soft key on either the radio or
RAM4 microphone will produce a calling beep to the other station.
9.15 INTERCOM OPERATION

The optional SSM-70H (RAM4) or SSM-72H (RAM4X) remote station micro-
phone must be connected to perform intercom functions between the GX2400
and the SSM-70H (RAM4) or SSM-72H (RAM4X).
NOTE
When using the intercom function, connect one SSM-70H (RAM4) or SSM-
72H (RAM4X) Remote Station Microphone to the GX2400.
9.15.1 Communication
1. [ ]  “IC”
2. Rotate the DIAL/ENT knob to select the device to

which you want to communicate, then press the
[SELECT] soft key. The “” icon will appear at the
left side of the selected station.
NOTE: When only one SSM-70H (RAM4) is connected to
GX2400, continue to step 5.
3. Repeat step 2 for all the desired devices.
4. Press the [ENTER] soft key.
5. When the intercom mode is enabled, “INTERCOM”
is displayed on the radio and SSM-70H (RAM4).
6. Press the microphone’s PTT switch on the radio. “Talk”
will be shown on the display.
NOTE: A warning beep will be heard when the radio’s PTT
and RAM4’s PTT switches are pushed at the same time.
7. Speak slowly and clearly into the microphone, hold the microphone about
1/2” (1.5 cm) away from your mouth.
41
8. When finished, release the PTT switch.
9. Press the CLEAR key to return to radio operation.
9.15.2 Calling
Pressing the [BELL] soft key when in intercom mode on either the radio or
RAM4 microphone will produce a calling beep to the other station.
9.16 VOICE SCRAMBLER

The voice scrambler function may only be enabled by your dealer. The 4-code
type (CVS2500A compatible) or the 32-code type (FVP-42 corresponding to
Furuno Electric M-4721), voice scrambler can be enabled in the CHANNEL
FUNCTION SETUP menu.
NOTE
The voice scrambler function is not available with the factory default settings.
Please contact your dealer to activate the voice scrambler function.
1. Select a channel that was programmed for scrambler

mode (the “ ” icon will appear on the display).
2. Monitor the channel before transmitting.
3. Transmit the voice message. The transmission sent
will be scrambled.
9.17 DEMO MODE

This mode is used by Standard Horizon sales persons and dealers to demon-
strate the transceiver’s DSC functions. Demo mode allows latitude, longitude
and time to be entered manually to simulate the displays. When the demo
mode is enabled, the transceiver will automatically switch from the NORMAL,
COMPASS, WAYPOINT and GM displays.
NOTE
When demo mode is enabled, if the transceiver is turned OFF and back ON
it will still be in the demo mode.
1. Press & hold [ ]  “ABOUT...”  “DEMO OPERATION”
2. Rotate the DIAL/ENT knob to select “DEMO POSITION INPUT”, then press
the [SELECT] soft key.
42
3. Enter the latitude and longitude of your vessel and
your local UTC time in the 24-hour notation. Press
the [◄] or [►] key to select the number and press
the [SELECT] soft key to move the cursor to the next
character.
4. If a mistake is made while entering the latitude, longitude or local UTC
time of your vessel, you can use the [◄] or [►] key to select “←” or “→”,
press the [SELECT] soft key until the incorrect character is selected, then
perform step 2 to make the correction.
5. To store the data entered, press the [FINISH] soft key.
6. Rotate the DIAL/ENT knob to select “DEMO START”,
7. Rotate the DIAL/ENT knob to select “START”, then

press the [ENTER] soft key.
NOTE
To exit the demo mode, select “STOP” in step 7 above.
43
10 GPS OPERATION
The GX2400 has an internal GPS receiver to acquire and display the satellite
position information*. When the radio is connected to an external GPS device
by the NMEA-0183 or NMEA2000, you may select the order of priority of the
connection devices to be used when obtaining location information via the
SETUP menu (Refer to section “19.1 ORDER OF PRIORITY”). Your position
information as well as received positions can be memorized and utilized later
for navigation.
10.1 DISPLAYING POSITION INFORMATION
10.1.1 GPS Information Numerical Display
1. [ ]  “GPS”  “GPS INFO”
2. The numerical data is displayed.

10.1.2 GPS Information Compass Display
1. [ ]  “GPS”  “COMPASS”
2. The compass data is displayed.

NOTE: Depending on the assignment of the soft keys you
may switch the screen immediately from the basic display
to the compass display by pressing the [COMP] soft key.
10.2 CHECKING GPS STATUS

1. [ ]  “GPS”  “GPS STATUS”
2. Display the GPS status currently being received.

44
10.3 GPS LOGGER OPERATION
The GX2400 includes a logger for position information that allows you to record
your location at regular intervals.
[LOGGER] soft key to turn the function on or off.
The recording starts and the display returns to the
previous screen with the “ ” icon on the top of the
display.
• You may change the log interval time of recording
via the SETUP menu (Refer to section “19.10.4
Logger Interval”).
NOTE: To utilize the records, connect the GX2400
to a PC and download the log data from the radio by
using the PC Programming Software. Refer to section
“22 CONNECTING A USB DATA TERMINAL TO THE PC”.
Logger operation alert:
• When the memory for log data becomes full, three beeps will sound and a
warning message will be displayed. Afterwards the logger does not operate
until the log data in the memory are erased.
• When the logger cannot record for some reason, three beeps will sound
and a warning message will be displayed. Afterwards the logger does not
operate anymore.
• An error message will be displayed when the radio cannot erase the log data
in the memory during the operation following the alert of memory full (see
above) or in the SETUP menu (Refer to section “19.10.5 Log Erase”).
45
11 DIGITAL SELECTIVE CALLING (DSC)
11.1 GENERAL
WARNING
This GX2400 is designed to generate a digital maritime distress and safety
call to facilitate search and rescue. To be effective as a safety device, this
equipment must be used only within communication range of a shore-based
VHF marine channel 70 distress and safety watch system. The range of
signal may vary but under normal conditions should be approximately 20
nautical miles.
Digital Selective Calling (DSC) is a semi-automated method of establishing a

radio call, it has been designated by the International Maritime Organization
(IMO) as an international standard for establishing VHF, MF and HF radio
calls. It has also been designated as part of the Global Maritime Distress and
Safety System (GMDSS). It is planned that DSC will eventually replace aural
watches on distress frequencies and will be used to announce routine and
urgent maritime safety information broadcasts.
This system allows mariners to instantly send a distress call with its own position,
to the Coast Guard and other vessels within range of the transmission. DSC
will also allow mariners to initiate or receive Distress, Urgency, Safety, Routine,
Position Request, Position Report, Automatic Position Polling, and Group calls
to or from another vessel equipped with a DSC transceiver.
11.2 DISTRESS ALERT

The GX2400 is capable of transmitting and receiving DSC distress messages.
Distress alerts transmitted from the transceiver include the latitude and longitude
of the vessel when valid GPS position data is being received.
11.2.1 Transmitting a Distress Alert

NOTE
To be able to transmit a DSC distress alert, the MMSI number must be

programmed, refer to section “8.6.1 Maritime Mobile Service Identity
(MMSI)”.
In order for the ships location to be transmitted, the GX2400 must receive
valid position data from the internal GPS receiver or another GPS device
connected with a NMEA 0183 or NEMA 2000 network. Refer to section “8.5.2
Accessory Cables”.
46
Basic Operation
1. Lift the red spring loaded [DISTRESS] cover, then press
and hold the [DISTRESS] key for 3 seconds. The radio
display will count down (3-2-1) and then transmit the
distress alert. The backlight of the display and keypad
flashes while the radio's display is counting down.
2. When the distress signal is sent, the transceiver
watches for a transmission on CH70 until an acknowl-
edgment signal (distress acknowledgement) is
received.
3. If no acknowledgment is received, the distress alert
is repeated in 4-minute intervals until an acknowledg-
ment is received.
4. When a distress acknowledgment is received, a
distress alarm sounds and Channel 16 is automati-
cally selected. The display shows the MMSI of the
ship responding to your distress.
5. Press the microphone PTT switch and state your name, vessel name,
number of persons on board and the distress situation, then say “over”
and wait for a reply from the acknowledging ship.
6. To turn the distress alarm OFF before the radio retransmits the distress
alert, press the [16/S] key or the [QUIT] soft key.
Transmitting a Distress Alert with Nature of Distress
The transceiver is capable of transmitting a distress alert with the following
“Nature of Distress” categories:
Undesignated, Fire/Explosion, Flooding, Collision, Grounding, Capsizing,
Sinking, Adrift, Abandoning, Piracy, MOB.
1. [ ]  “DSC CALL”  “DIST ALERT MSG”
2. Press the [NATURE] soft key. The “NATURE OF”

menu will appear on the display.
3. Rotate the DIAL/ENT knob to select the desired nature of distress category,
4. Press and hold the DISTRESS key until a distress alert is transmitted.
47
Transmitting a Distress Alert by Manually Inputting Location and Time
In case the transceiver fails to get a GPS position fix, you may manually input
the latitude, longitude and time before transmitting the distress alert.
1. [ ]  “DSC CALL”  “DIST ALERT MSG”
2. Press the [POS/TM] soft key.

the latitude, then press the [SELECT] soft key to step
to the next number.
4. Repeat step 3 to set the position and time.
If a mistake is made, press the [◄] or [►] key to select
“←” or “→”, press the [SELECT] soft key until the incor-
rect character is selected, then perform step 3.
5. When finished programming the position and time, press the [FINISH] soft
key. The display will return to the previous screen.
6. Press and hold the [DISTRESS] key until a distress alert is transmitted.
Pausing a Distress Alert
After a distress alert is transmitted, the distress alert is repeated every 4 minutes
until the call is canceled by the user or until the radio is turned OFF and ON
again. The transceiver has the capability to suspend (pause) the retransmitting
of the distress alert by the procedure below.
1. After the distress alert is transmitted, the radio will
show the display as on the right.
Looking at this display you will notice “TX IN: 02:10”,
this is the time when the radio will re-transmit the
distress alert.
2. To suspend re-transmitting the distress alert call, press
the [PAUSE] soft key.
3. To resume counting down to transmit the distress
alert, press the [RESUME] soft key.
48
Canceling a Distress Alert
If a distress alert was sent by error, the transceiver allows you to send a message
to other vessels to cancel the distress alert that was made.
1. Press the [CANCEL] soft key, then press the [YES]
soft key.
2. After the message for canceling has been transmitted,

press the [OK] soft key.
3. Press the [FINISH] soft key.
4. Press the [QUIT] soft key to return to radio operation.
11.2.2 Receiving a Distress Alert

1. When a distress alert is received, an emergency alarm
sounds.
2. Press any key to stop the alarm.
3. Rotate the DIAL/ENT knob to show information on

the vessel in distress.
On the display you will notice 3 soft key selections.
These selections are described below:
[ACCEPT]: Press this key to accept the distress alert and switch to Channel 16.
NOTE: If a key is not pressed within 30* seconds the radio will automatically switch
to Channel 16. *(“AUTO CHANNEL CHANGE” timer settings can be changed in
“DSC SETUP” menu. The default setting is 30 sec.)
[PAUSE]: Press this key to temporarily pause automatic switching to Channel 16.
[QUIT]: Press this key to end quit the automatic Channel 16 switching and
revert to the last selected working channel.
4. After accepting the call, press the [TO WPT] soft
key to set the location of the vessel in distress as a
destination for navigation.
NOTE: You may change the waypoint name.
49
5. Rotate the DIAL/ENT knob to select “SAVE & GOTO”,
then press the [SELECT] soft key to change the
display to the waypoint navigation screen. The display
indicates the distance and direction of the vessel in
distress, and the compass displays the distressed
vessel with a dot ().
6. To stop navigating to a waypoint, press one of the
soft keys, then press the [STOP] soft key. The radio
is switched to the normal mode.
NOTE
• You must continue monitoring Channel 16 as a coast station may require
assistance in the rescue attempt.
• When there is an unread distress alert, an “ ” icon will appear on the
display. You may review the unread distress alert from the DSC log, refer
to section “11.10.2 Reviewing a Logged DSC RX Distress Alert and
acknowledgement”.
11.3 ALL SHIPS CALL

The all ships call function allows contact to be established with DSC equipped
vessels without having their MMSI in the individual calling directory. Also, priority
for the call can be designated as “SAFETY” or “URGENCY”.
SAFETY Call: This type of DSC call is used to transmit boating safety informa-
tion to other vessels. This message usually contains information
about an overdue boat, debris in the water, loss of a navigation
aid or an important meteorological message. This call is the
same as transmitting “Securite, Securite, Securite” by voice.
URGENCY Call: This type of call is used when a vessel may not truly be
in distress, but have a potential problem that may lead to
a distress situation. This call is the same as transmitting
“PAN PAN, PAN PAN, PAN PAN” on Channel 16.
11.3.1 Transmitting an All Ships Call
1. [ ]  “DSC CALL”  “ALL SHIPS”
2. Rotate the DIAL/ENT knob to select the nature of

the call (“SAFETY” or “URGENCY”), then press the
[SELECT] soft key.
50
3. In the INTERSHIP CH list, rotate the DIAL/ENT knob
to select the operating channel on which you want to
communicate, then press the [SELECT] soft key. To
select operating channels from all voice channels,
press the [MANUAL] soft key.
4. Press the [YES] soft key to transmit the selected type
of all ships call.
5. After the all ships call is transmitted, the transceiver
will switch to the selected channel.
6. Listen to the channel to make sure it is not busy, then
key the microphone and say “PAN PAN, PAN PAN,
PAN PAN” or “Securite, Securite, Securite” depending
on the priority of the call.
7. Press the [QUIT] soft key to exit the all ships call
menu.
11.3.2 Receiving an All Ships Call

1. When an all ships call is received, an emergency
alarm will sound.
The display shows the MMSI of the vessel transmit-
ting the all ships call and the radio will change to
the requested channel after 30 seconds (the default
setting of “AUTO CHANNEL CHANGE”).
3. Monitor the requested channel until the all ships voice
communication is completed.
On the display you will notice 3 soft key selections.
[ACCEPT]: Press this key to accept the DSC all ships
call and to switch to requested channel.
NOTE: If a key is not pressed for 30* seconds or longer the radio will automatically
change to the requested channel.
*(The default setting of “AUTO CHANNEL CHANGE”)
[PAUSE]: Press this key to temporarily pause automatic switching to the
requested channel.
NOTE: In some cases, automatically switching to the requested channel might disrupt
important ongoing communications. Commercial users may suspend channel switch-
ing and remain on the working channel in use before the all ships call was received.
[QUIT]: Press this key to quit the automatic channel switching and revert
to the last selected working channel.
51
4. Press the [QUIT] key to return to the channel display.
NOTE
When there is an unread all ships call, an “ ” icon will appear on the display.
You may review the unread all ships call from the DSC log, refer to section
“11.10.2 Reviewing a Logged DSC RX Distress Alert and acknowledge-
ment”.
11.4 INDIVIDUAL CALL

This feature allows the GX2400 to contact another vessel with a DSC VHF
radio and automatically switch the receiving radio to the desired communica-
tions channel. This feature is similar to calling a vessel on CH16 and requesting
to go to another channel (switching to the channel is private between the two
vessels). Up to 100 individual contacts may be programmed.
11.4.1 Setting up the Individual / Position Call Directory

The transceiver has a DSC individual directory that allows storing vessels or persons
names and the associated MMSI numbers you may wish to contact via individual
calls, auto polling, position request, position report, and polling transmissions.
To transmit an individual call, you must program this directory with information
of the persons you wish to call, similar to a cellular phone contact list.
1. Press & hold [ ]  “DSC SETUP”  “INDIVIDUAL DIRECTORY”
2. Rotate the DIAL/ENT knob to select “ADD”, then

press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select “NAME:”, then

4. Press the [◄] or [►] key to select the letters of the name of
the vessel or person you want to reference in the directory.
5. Press the [SELECT] soft key to store the first letter in
the name and step to the next letter to the right.
52
6. Repeat steps 4 and 5 until the name is complete. The name can consist of
up to fifteen characters, and if you do not use all fifteen characters, select
“→” to move to the next space. The “→” can also be used to enter a blank
space in the name.
If a mistake is made entering in the name, press the [◄] or [►] key to select
“←” or “→”, press the [SELECT] soft key until the incorrect character is
selected, then perform steps 4 and 5.
7. When finished entering the name (using eleven characters or less), press
the [FINISH] soft key to advance to the MMSI number entry.
8. Rotate the DIAL/ENT knob to select “MMSI:”, then press the [SELECT] soft
key.
9. Press the [◄] or [►] key to select numbers, 0 - 9. To enter the desired
number and move one space to the right by pressing the [SELECT] soft key.
Repeat this procedure until all nine space of the MMSI number are entered.
If a mistake is made entering in the MMSI number, press the [◄] or [►]
key to select “←” or “→”, press the [SELECT] soft key until the incorrect
character is selected, then perform step 9.
10. When finished entering the MMSI number, press the [FINISH] soft key.
11. To store the entered data, Rotate the DIAL/ENT knob
to select “SAVE”, then press the [ENTER] soft key.
12. To enter another individual address, repeat steps 2
through 11.
11.4.2 Setting up the Individual Call Reply
This menu item sets up the radio to manually (default setting) or automatically
respond to a DSC individual call requesting you to switch to a working channel
for voice communications. When “MANUAL” is selected the MMSI of the calling
vessel is shown allowing you to see who is calling. This function is similar to
caller ID on a cellular phone.
1. Press & hold [ ]  “DSC SETUP”  “INDIVIDUAL REPLY”
2. Rotate the DIAL/ENT knob to select “AUTO” or

“MANUAL”.
setting.
53
11.4.3 Enabling the Individual Call Acknowledgment
The radio can select either reply message “ABLE” (default) or “UNABLE” when the
individual reply setting (described in the previous section) is set to “AUTOMATIC”.
1. Press & hold [ ]  “DSC SETUP”  “INDIVIDUAL ACK.”
2. Rotate the DIAL/ENT knob to select “ABLE” or

“UNABLE”.
setting.
11.4.4 Transmitting an Individual Call
This feature allows the user to contact another vessel with a DSC transceiver,
and is similar to calling a vessel on CH16 and requesting to go to another
channel.
Individual Call using the Individual/Position Directory
1. [ ]  “DSC CALL”  “INDIVIDUAL CALL”
2. Rotate the DIAL/ENT knob to select “HISTORY” or

“MEMORY”, then press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select an individual you

want to contact, press the [SELECT] soft key.

5. Press the [YES] soft key to transmit the individual
DSC signal.
6. When an individual call acknowledgment is received,

the operating channel is automatically changed to
the channel which is selected in step 4 above and a
ringing tone sounds.
54
7. Press the [QUIT] soft key to listen to the channel to
make sure it is not busy, then press the microphone
PTT switch and talk into the microphone to commu-
nicate with the other vessel.
Individual Call by Manually Entering an MMSI
You may enter an MMSI contact number manually without storing it in the
individual directory.
1. [ ]  “DSC CALL”  “INDIVIDUAL CALL”
2. Rotate the DIAL/ENT knob to select “NEW ID”, then


the MMSI which you want to contact, then press the
[SELECT] soft key to step to the next number.
4. Repeat step 3 to set the MMSI number (nine digits).
If a mistake is made while entering the MMSI number,
selected, then perform step 3 to enter the corrections.
5. When finished entering the MMSI number, press the
[FINISH] soft key.
communicate, then press the [SELECT] . To select
operating channels from all voice channels, press the
[MANUAL] soft key.
7. Press the [YES] soft key to transmit the individual
DSC call.
8. When an individual call acknowledgment is received,
the operating channel is automatically changed to
the channel which is selected in step 6 above and a
ringing tone sounds.
9. Press the [QUIT] soft key to listen to the channel and
make sure it is not busy, then press the microphone
PTT switch and talk into the microphone to commu-
nicate with the other vessel.
55
11.4.5 Receiving an Individual Call
When an individual DSC call is received, the MMSI (Maritime Mobile Service
Identity Number) or person's name is displayed, you may choose whether or
not to send your position to the requesting vessel. Refer to section “11.4.2
Setting up the Individual Call Reply” to change the reply to “AUTO” if you
want to automatically replying to the call.
Manual reply (Default setting):
1. When an individual call is received, a ringing alarm
sounds.
The display shows the MMSI of the vessel transmitting
the individual call.
3. The 3 soft key selections shown on the display are
described below:
[ACCEPT]: Press this key to accept the DSC indi-
vidual call, and switch to the requested channel.
[PAUSE]: Press this key to temporarily pause auto-
matically switching to the requested channel.
NOTE: In some cases, automatically switching to a requested channel might disrupt
important ongoing communications. Commercial users may suspend channel
switching and remain on the working channel in use before the individual call was
received.
[QUIT]: Press this key to exit the automatic channel switching and revert
NOTE: If a key is not pressed within 30 seconds, the transceiver will automatically
change to radio operation.
4. After accepting the call, press the [ABLE] soft key to
switch to the requested channel. (To inform the call-
ing vessel that you are unable to respond, press the
[UNABLE] soft key.)
5. Press the [YES] soft key to send an acknowledgement.
Press the [CHG CH] soft key to change to the
requested operating channel for communication.
6. Monitor the specified channel until the message is completed.
Press the microphone PTT switch and talk into the microphone to commu-
nicate with the vessel that initiated the individual call.
7. Press the [QUIT] soft key to return to the channel
display.
56
Automatic reply:
1. When an individual call is received, a ringing alarm
sounds.
The radio automatically switches to the requested chan-
nel. The display shows the MMSI of the vessel calling.
3. Monitor the requested channel until the message is completed.
Press the microphone PTT switch and talk into the microphone to commu-
nicate with the vessel that initiated the individual call.
NOTE
When there is an unread individual call, the “ ” icon will appear on the
display. You may review the unread individual call from the DSC log, refer
to section “11.10.2 Reviewing a Logged DSC RX Distress Alert and
acknowledgement”.
11.4.6 Setting up the Individual Call Ringer

When an individual call is received the call ringer will sound for 2 minutes (default
setting). This selection allows the individual call ringer time to be changed.
1. Press & hold [ ]  “DSC SETUP”  “INDIVIDUAL RING”
2. Rotate the DIAL/ENT knob to select the individual call

ringing time.
The GX2400 individual call ringer may be set to OFF:
1. [Press & hold [ ]  “DSC SETUP”  “DSC BEEP”
2. Rotate the DIAL/ENT knob to select “INDIVIDUAL

CALL”, then press the [SELECT] soft key.
57
3. Rotate the DIAL/ENT knob to select “OFF”.
To enable the ringer tone, repeat the above procedure, Rotate the DIAL/ENT
knob to select “ON” in step 3 above.
11.5 GROUP CALL

This feature allows users to automatically contact a specific group of vessels
using DSC radios with the group call function. The called radios can automati-
cally switch to the desired channel for voice communications. This function is
very useful for yacht clubs and vessels traveling together that want to make
communal announcements on a predetermined channel. Up to 30 group MMSIs
may be programmed.
11.5.1 Setting up a Group Call

For this function to operate, the same group MMSI (Maritime Mobile Service
Identity Number) must be programmed into all the DSC VHF radios within the
group of vessels that will be using this feature. To understand Group MMSI
programming, first a ship MMSI has to be understood.
Ship MMSI: The first three digits called MID (Mobile Identity Group) of a ship
MMSI denote the country where the ship’s MMSI is registered. The last 6 digits
are specific to the ships ID.
Ship MMSI Example: If your MMSI is “366123456”, “366” is MID which denote
the country and “123456” is the vessel’s MMSI.
Group MMSI:
 Group MMSI numbers are not assigned by the FCC or other organizations
licensed to assign ship MMSI numbers.
 The first digit of a group MMSI is always set to “0” by International rules. All
Standard Horizon radios are preset so when programming a group MMSI
the first digit is set to “0”.
 The ITU (International Telecommunication Union) recommends program-
ming the MID of a ship MMSI into the Second, Third and Fourth digits of
the group MMSI as it denotes the area where the ship is located.
 The last 5 digits are decided upon by persons in the group. This is an impor-
tant step as all radios in the group must contain the same group MMSI in
order to be contacted by each other. There is a chance that another group of
vessels may program the same group MMSI. If this happens, simply change
one or more of the last 5 digits of the group MMSI.
58
1. [Press & hold [ ]  “DSC SETUP”  “GROUP DIRECTORY”

3. Rotate the DIAL/ENT knob to select “GP NAME:”,

4. Press the [◄] or [►] key to select the first letter of

the name of the group you want to reference in the
directory.
5. Press the [SELECT] soft key to store the first letter of
6. Repeat steps 4 and 5 until the name is complete. The name can consist of
up to fifteen characters, if you do not use all eleven characters, select “→”
to move to the next space. This method can also be used to enter a blank
space in the name.
If a mistake is made entering the name, press the [◄] or [►] key to select
“←” or “→”, press the [SELECT] soft key until the incorrect character is
selected, then perform steps 4 and 5.
7. When finished entering the group name (using fifteen characters or less),
press the [FINISH] soft key to advance to the group MMSI number entry.
8. Rotate the DIAL/ENT knob to select “GP MMSI:”, then
9. Press the [◄] or [►] key to select the second number
of the MMSI (the first of the nine digits is permanently
set to “0”) which you want to contact, then press the
[SELECT] soft key to step to the next number.
Repeat this procedure until all eight spaces of the MMSI number are entered.
10. When finished entering the MMSI number, press the [FINISH] soft key to
confirm.
11. To store the data, select “SAVE”, then press the [SELECT] soft key.
12. To enter another group address, repeat steps 2 through 11.
59
11.5.2 Transmitting a Group Call
Group Call using the Group Directory
1. [ ]  “DSC CALL”  “GROUP CALL”

3. Rotate the DIAL/ENT knob to select a group you want

to contact, then press the [SELECT] soft key

5. Press the [YES] soft key to transmit the group call
signal.
6. When the group call signal is sent, the display will be

as shown in the illustration at the right.
7. After the group call is transmitted, all the radios in the

group will switch to the designated channel.
press the microphone PTT switch to communicate
with all of the vessels in the group.
Group Call by Manually Entering an MMSI
This feature allows you to contact a group of vessels by entering in their group
MMSI manually.
1. [ ]  “DSC CALL”  “GROUP CALL”

60
3. Rotate the DIAL/ENT knob to select the second
number of the MMSI (the first of nine digits is perma-
nently set to “0”) which you want to contact, then press
the [SELECT] soft key to step to the next number.
4. Repeat step 3 to set the MMSI number.
character is selected, then perform steps 3 and 4.
to select the operating channel on which to commu-
nicate, then press the [SELECT] soft key. To select
operating channels from all voice channels, press the
[MANUAL] soft key.
7. Press the [YES] soft key to transmit the group call
signal.
8. After the group call is transmitted, all the radios in the

group will switch to the designated channel.

press the microphone PTT switch to communicate
with all of the vessels in the group.
11.5.3 Receiving a Group Call

1. When a group call is received, the transceiver will
produce a ringing alarm sound.
2. The display shows the group MMSI number.
On the display 3 soft key selections are shown. These
selections are described below:
[ACCEPT]: Press this key to accept the group call
and switch to the requested channel.
[PAUSE]: Press this key to temporarily pause auto-
matic switching to the requested channel.
[QUIT]: Press this key to exit the automatic channel switching and revert
61
4. If you want to respond, monitor the channel to make sure it is clear, then
press the microphone PTT switch and talk into the microphone to commu-
nicate with all of the vessels in the group.
NOTE: If a key is not pressed within 30 seconds, the radio
will automatically change to radio operation.
NOTE
When there is an unread group call, the “ ” icon will appear on the display.
You may review the unread group call from the DSC log, refer to section
“11.10.3 Reviewing Other Logged Calls”.
11.5.4 Setting up the Group Call Ringer

The transceiver group call ringer may be turned OFF using the following
procedure:
1. Press & hold [ ]  “DSC SETUP”  “DSC BEEP”
2. Rotate the DIAL/ENT knob to select “GROUP CALL”,


To enable the ringer tone, repeat the above procedure, rotate the DIAL/ENT
knob to “ON” in step 3 above.
11.6 POSITION REQUEST

Advancements in DSC have made it possible to poll the location of another
vessel and show the position of that vessel on the display of the GX2400.
Standard Horizon has taken this feature one step further, if a compatible GPS
chart plotter is connected to the GX2400, the polled position of the vessel is
shown on the display of the GPS chart plotter making it easy to navigate to the
location of the polled vessel. This is a great feature for anyone wanting to know
the position of another vessel. For example, find where your buddy is catching
fish or find the location of a vessel you are cruising with.
62
NOTE
The other vessel must have an operating GPS receiver connected to its
DSC radio, and the radio must not be set to deny position requests. (Refer
the section “11.4 INDIVIDUAL CALL” to enter information into the individual
directory).
11.6.1 Setting up a Position Request Reply

The transceiver can be set up to automatically (default setting) or manually send
your position when requested by another vessel. This selection is important if
you are concerned about someone polling the position of your vessel that you
may not want to. In the manual mode you will see the MMSI (Maritime Mobile
Service Identity Number) or persons name shown on the display allowing you
to choose whether or not to send your position to the requesting vessel.
1. Press & hold [ ]  “DSC SETUP”  “POSITION REPLY”

“MANUAL”. In “AUTO” mode, after a DSC POS request
is received, the radio will automatically transmit your
vessel’s position. In “MANUAL” mode, the display of
the transceiver will show who is requesting the position
and the [YES] soft key on the radio must be pressed
to send your position to the requesting vessel.
11.6.2 Transmitting a Position Request to Another Vessel
Position Request using the Individual/Position Directory
Refer to section “11.4 INDIVIDUAL CALL” to enter information into the indi-
vidual directory.
1. [ ]  “DSC CALL”  “POS REQUEST”

3. Rotate the DIAL/ENT knob to select a name that is

stored in the individual/position directory.
63
4. Press the [SELECT] soft key, then press the [YES]
soft key to transmit the position request DSC call.
5. When the transceiver receives the position from the
polled vessel it is shown on the radio display.
NOTE
If the transceiver does not receive position data from the polled vessel, the
display will show as follows.
--.--.---- _
---.--.---- _
Position Request by Manually Entering an MMSI

This feature allows you to request the position of a vessel by manually enter-
ing the MMSI.
1. [ ]  “DSC CALL”  “POS REQUEST”

3. Press the [◄] or [►] key to select the first number

of the MMSI (nine digits) which you want to contact,
then press the [SELECT] soft key to step to the next
number.
4. Repeat step 3 to set the MMSI number.
5. When finished entering the MMSI number, press the
[FINISH] soft key.
6. Press the [YES] soft key to transmit the position
request DSC call.
64
7. When the transceiver receives the position from the
polled vessel it is shown on the radio display.
NOTE
The received position from the polled vessel can be transferred to a GPS
chart plotter via NMEA DSC and DSE sentences.
11.6.3 Receiving a Position Request

1. When a position request call is received from another
vessel, a ringing sound will be produced, and the
display will be as shown in the illustration at the right.
3. To send your vessel’s position to the requesting
vessel, press the [REPLY] soft key.
Or to exit from position request display, press the
[QUIT] soft key.
4. Press the [QUIT] soft key to return to the channel
display.
NOTE
When there is an unread position request call, the “ ” icon will appear on
the display. You may review the unread individual call from the DSC log, refer
to section “11.10.3 Reviewing Other Logged Calls”.
11.6.4 Manual Input of Position Information

If the transceiver is located in an area where GPS reception is limited when
you are going to reply to the received position request, you may manually input
your location (latitude and longitude) and time to be sent.
1. [ ]  “MMSI/POS INFO”
2. Press the [POS/TM] soft key.
65
latitude, then press the [SELECT] soft key to step to
the next number.
4. Repeat step 3 to set the position and time.
If a mistake is made, press the [◄] or [►] key to select
“←” or “→”, press the [SELECT] soft key until the incor-
rect character is selected, then perform step 3.
5. When finished programming the position and time, press the [FINISH] soft
key. The display will return to the previous screen.
6. Press the [OK] soft key.
11.6.5 Setting up a Position Request Ringer

The transceiver has the capability to turn off the position request ringer.
2. Rotate the DIAL/ENT knob to select “POS REQUEST”,


setting.
knob to select “ON” in step 3 above.
11.7 POSITION REPORT

The feature is similar to position request, however instead of requesting a position
of another vessel this function allows you to send your position to another vessel.
11.7.1 Transmitting a DSC Position Report Call

DSC Position Report Call using the Individual/Position Directory
Refer to section “11.4 INDIVIDUAL CALL” to enter information into the indi-
vidual directory.
1. [ ]  “DSC CALL”  “POS REPORT”
66
3. Rotate the DIAL/ENT knob to select the name in the

directory, then press the [SELECT] soft key.
4. If you want to change the position displayed, press

the [POS/TM] soft key to go to the position information
input screen. After inputting new position information,
press the [FINISH] soft key to confirm.
5. Press the [YES] soft key to send your position to the
selected vessel.
DSC Position Report Call by Manually Entering an MMSI

This feature allows you to send your position to another vessel by manually
entering the MMSI of the ship you want to send your position to.
1. [ ]  “DSC CALL”  “POS REPORT”

3. Rotate the DIAL/ENT knob to select the first number of

the MMSI of the vessel you want to contact, then press
the [SELECT] soft key to step to the next number.
4. Repeat step 3 to complete the MMSI number.
6. If you want to change the position displayed, press the [POS/TM] soft key
to go to the position information input screen. After inputting the new posi-
tion information, press the [FINISH] soft key to confirm.
67
7. Press the [YES] soft key to send your position to the
selected vessel.
11.7.2 Receiving a DSC Position Report Call

When another operator transmits their vessels location to another GX2400
receiver the following will happen:
1. When a position report call is received from another

vessel, a ringing sound will be produced.
2. Press any key to stop ringing.
3. To exit to radio mode, press the [QUIT] soft key.
11.7.3 Navigating to the Reported Position

The transceiver has a feature that permits navigate to a received position report
call by using the compass display. Navigation to the location of a position report
call may be enabled by the procedure below.
1. Press the [TO WPT] soft key.
2. Press the [ENTER] soft key to save the waypoint into

memory.
3. The display indicates the distance and direction of

the received vessel, and the compass displays the
received vessel with a dot ().
Stopping Navigation to the Reported Position

1. Press one of the soft keys, then press the [STOP] soft key.
The radio will stop navigating to the waypoint and the
normal VHF display will be shown.
68
11.7.4 Saving the Reported Position as a Waypoint
The transceiver can save a position report call in the radio’s memory as a
waypoint.
1. After the position report call has been received, press
the [SAVE] soft key.
2. If you want to change the name of the waypoint, rotate

the DIAL/ENT knob to select “NAME”, then press the
[SELECT] soft key.
3. Enter the name of the waypoint you want to reference
in the directory. For details, refer to “11.4.1 Setting
up the Individual / Position Call Directory”.
4. Press the [ENTER] soft key to save the waypoint into
memory.
5. Press the [OK] soft key to return to the position report

display.
Navigating to a Saved Waypoint
Refer to section “12.1.1 Starting and Stopping Navigation” for details.
11.7.5 Setting up a Position Report Ringer

The transceiver position report ringer may be turned OFF.
2. Rotate the DIAL/ENT knob to select “POS REPORT”,


setting.
knob to select “ON” in the step 3 above.
69
11.8 AUTO POSITION POLLING
The transceiver has the capability to automatically track six vessels programmed
into the individual directory, or to automatically send your position information
to the programmed stations.
11.8.1 Setting up the Polling Operation
1. Press & hold [ ]  “DSC SETUP”  “AUTO POSITION POLLING”

operation (AUTO POS REQUEST and AUTO POS
REPORT), and press the [ENTER] soft key.
11.8.2 Setting up the Polling Time Interval
1. Press & hold [ ]  “DSC SETUP”  “AUTO POS INTERVAL”

interval time (30 second, 1, 2, 3, and 5 minutes) and
11.8.3 Selecting Vessels to be Automatically Polled
NOTE
The radio uses the individual directory to select vessels to be automatically
polled. Refer to section “11.4.1 Setting up the Individual / Position Call
Directory” and enter the MMSI of vessels you may want to poll before
proceeding.
1. [ ]  “DSC CALL”  “AUTO POS POLLING”
2. Rotate the DIAL/ENT knob to select “SELECTED ID”,

3. The radio will show a highlighted blank row when you

select the vessel for the first time. Press the [SELECT]
soft key.
70
4. The radio will show the vessels programmed in the indi-
vidual directory. Rotate the DIAL/ENT knob to select
the desired vessel, then press the [ENTER] soft key.
5. For more entries, rotate the DIAL/ENT knob to select a

blank row, press the [SELECT] soft key, then perform
step 4.
6. When finished, press the [CLEAR] key to exit to the
radio mode.
11.8.4 Enabling/Disabling Auto POS Polling
1. [ ]  “DSC CALL”  “AUTO POS POLLING”
2. Rotate the DIAL/ENT knob to select “ACTIVATION”,

3. Rotate the DIAL/ENT knob to select “START” to

enable transmissions or “STOP” to disable, then press
the [ENTER] soft key.
5. Auto POS Polling starts and the “ ” icon will appear
on the display.
11.9 DSC TEST

This function is used to contact another DSC equipped vessel to ensure the
DSC functions of the radio are operating.
NOTE
To use the DCS Test feature, a radio that is to receive the test call also needs
to have the DSC Test feature.
To perform the DSC test you will need to enter the MMSI of another vessel into
the individual directory or manually enter the MMSI using the procedure below.
11.9.1 Programming MMSI into Individual Directory

Refer to section “11.4.1 Setting up the Individual / Position Call Directory”.
71
11.9.2 Transmitting a DSC Test to Another Vessel
DSC Test call using the Individual/Position Directory
1. [ ]  “DSC CALL”  “DSC TEST CALL”

3. Rotate the DIAL/ENT knob to select the ship name,

4. Press the [YES] soft key to transmit the DSC test call
to the other vessel.
DSC Test Call by Manually Entering an MMSI
1. [ ]  “DSC CALL”  “DSC TEST CALL”  “MANUAL”

3. Rotate the DIAL/ENT knob to select the first digit in

the MMSI, then press the [SELECT] soft key.
4. Repeat step 3 until all the numbers of the MMSI are
shown on the display.
5. Press the [FINISH] soft key to show the test call page.
6. Press the [YES] soft key to transmit the DSC test call
to the other vessel.
72
NOTE
When the radio receives a test call reply from the vessel that was called, the
radio will ring and show “RX TEST CALL” on the display, this confirms the
called radio has received the test call.
11.9.3 Receiving a DSC Test Call

When another vessel transmits a DSC Test call to the GX2400 following will
happen:
1. When a DSC Test call is received, the radio will auto-
matically respond to the calling vessel.
2. To exit from the DSC Test call display, press the [QUIT]
soft key.
11.10 DSC LOG OPERATION

The GX2400 logs transmitted calls, received DSC distress calls, and other calls
(individual, group, all ships, etc.). The DSC log feature is similar to an answer
machine where calls are recorded for review and an “ ” icon will appear on
the radio's display. The GX2400 can store up to 100 transmitted calls, up to the
latest 50 distress calls, and up to the latest 100 other calls (individual, group, all
ships, position report, position request acknowledge and test call acknowledge).
NOTE
When the “DSC LOG” menu is selected, the transceiver may display high-
priority logged calls automatically.
11.10.1 Reviewing and Resending a Transmitted Logged Call

The transceiver allows transmitted logged calls to be reviewed and resent.
1. [ ]  “DSC CALL”  “DSC LOG”
2. Rotate the DIAL/ENT knob to select “TRANSMIT-

TED”, then press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select the station (name or

MMSI number) you want to review and/or resend the call.
4. Press the [SELECT] soft key to review details of the
selected station.
73
5. Press the [CALL] soft key to resend the DSC call or
press the [BACK] soft key to go back to the transmit-
ted DSC call list.
11.10.2 Reviewing a Logged DSC RX Distress Alert and acknowledgement

The transceiver allows logged DSC RX distress alerts and acknowledgements
to be reviewed.
1. [ ]  “DSC CALL”  “DSC LOG”  “RX DISTRESS”
2. Rotate the DIAL/ENT knob to select the station (name

or MMSI number) of the distress alert you want to
review its acknowledgement.
NOTE: When there is an unread received call, the “ ” icon
will appear to the left of the logged call.
3. Press the [SELECT] soft key to review details for the
selected station.
4. Press the [INFO] soft key to display more informa-
tion or press the [BACK] soft key to go back to the
received DSC distress call list.
11.10.3 Reviewing Other Logged Calls
1. [ ]  “DSC CALL”  “DSC LOG”  “RX OTHER CALL”
2. Rotate the DIAL/ENT knob to select the station (name

or MMSI number) you want to review and/or call back.
NOTE: When received call is unread, the “ ” icon will
appear to the left of the logged call.
3. Press the [SELECT] soft key to review details of the
selected station.
4. Press the [REPLY] soft key to reply to the call or press
the [BACK] soft key to return to the received call list.
74
11.10.4 Deleting Logged Calls from the DSC Log Directory
1. [ ]  “DSC CALL”  “DSC LOG”  “LOG DELETE”
2. Rotate the DIAL/ENT knob to select the category

(“TRANSMITTED”, “RX DISTRESS”, “RX OTHER
CALL” or “ALL LOG”) to be deleted.
3. Press the [SELECT] soft key.
The display will show “Do you want to delete the LOG?”.
4. Press the [YES] soft key. (To cancel, press the [NO]
soft key.)
NOTE
The procedure above will delete all logged calls of the selected category at
one time.
To delete logged calls one by one, review the details of the call you want to
delete, then press the [DELETE] soft key.
75
12 NAVIGATION
The GX2400 is capable of storing up to 250 waypoints for navigation using
the compass page.
You can also navigate to a DSC distress call with location data, or to the posi-
tion received from another DSC radio using DSC polling.
12.1 WAYPOINT OPERATION

12.1.1 Starting and Stopping Navigation
Navigation Using the Waypoint Directory
1. [ ]  “NAVI”  “WAYPOINT”

category (“HISTORY” or “MEMORY”), then press the
[SELECT] soft key.
3. Rotate the DIAL/ENT knob to select a waypoint, then
press the [SELECT] soft key. The navigation screen
will appear.
The navigation screen includes the distance and
direction to the destination. The destination waypoint
is indicated by a dot () inside the compass.
4. Press one of the soft keys, then press the [STOP] soft
key to exit the navigation screen.
Navigation by Manually Entering a Waypoint
1. [ ]  “NAVI”  “WAYPOINT”
2. Rotate the DIAL/ENT knob to select “MANUAL”, then

3. If you want to give the waypoint an easy-to-find name,
rotate the DIAL/ENT knob to select “NAME:”, press
the [SELECT] soft key, then enter the name. For
details, refer to “11.4.1 Setting up the Individual /
Position Call Directory”.
4. Rotate the DIAL/ENT knob to select “POSITION:”,
76
5. Rotate the DIAL/ENT knob to select the first number
of latitude, then press the [SELECT] soft key to step
to the next number.
6. Repeat step 5 to set the position.
If a mistake is made, press the [◄] or [►] key to select “←” or “→”, press
the [SELECT] soft key until the incorrect character is selected, then perform
step 5.
7. When finished programming the position, press the [FINISH] soft key. The
display will return to the previous screen.
8. Rotate the DIAL/ENT knob to select “SAVE & GOTO”,
The navigation screen will appear.
The screen includes the distance and direction to
the destination. The destination and the waypoint is
indicated by a dot () inside the compass.
12.1.2 Setting Up Waypoint Directory

Marking a Position
This feature allows the radio to mark the current position of the vessel.
1. Press & hold [ ]  “WAYPOINT SETUP”  “MARK POSITION”
2. If you want to modify the name, rotate the DIAL/ENT

knob to select “NAME:”, then press the [SELECT] soft
key.
3. Enter the waypoint name by rotating the DIAL/ENT
knob and the [SELECT] soft key.
When finished entering the name (using fifteen char-
acters or less), press the [FINISH] soft key.
4. If you want to modify the position, rotate the DIAL/ENT knob to select
“POSITION:”, press the [SELECT] soft key, then enter the new coordinates.
When finished modifying the position, press the [FINISH] soft key.
5. Rotate the DIAL/ENT knob to select “SAVE”, then press
the [SELECT] soft key to save the mark position into
memory.
77
Adding a Waypoint
1. Press & hold [ ]  “WAYPOINT SETUP”  “WAYPOINT DIRECTORY”


4. Enter the waypoint name by pressing the [◄] or [►]
key and the [SELECT] soft key.
When finished entering the name (using fifteen characters or less), press
the [FINISH] soft key.
5. Rotate the DIAL/ENT knob to select “POSITION:”, press the [SELECT]
soft key, then enter the waypoint coordinates.
When finished entering the position, press the [FINISH] soft key.
6. Rotate the DIAL/ENT knob to select “SAVE”, then press
the [SELECT] soft key to save the waypoint into memory.
Editing a Waypoint
2. Rotate the DIAL/ENT knob to select “EDIT”, then

3. Rotate the DIAL/ENT knob to select the waypoint to

be edited, then press the [SELECT] soft key to show
the waypoint input display.
4. Rotate the DIAL/ENT knob to select “NAME:” or
“POSITION:”, then press the [SELECT] soft key.
5. Press the [◄] or [►] key to select “←” or “→”, press the [SELECT] soft key
until the character to be changed is selected, then enter a new character.
6. Repeat step 5 until the waypoint is updated.
When finished editing, press the [FINISH] soft key.
7. Rotate the DIAL/ENT knob to select “SAVE”, then
press the [SELECT] soft key to store the edited
waypoint into memory.
78
Deleting a Waypoint
2. Rotate the DIAL/ENT knob to select “DELETE”, then

3. Rotate the DIAL/ENT knob to select the waypoint to

be deleted, then press the [SELECT] soft key.
4. Confirm the waypoint to be deleted, rotate the DIAL/ENT

knob to select “OK”, then press the [SELECT] soft key.
Saving a DSC Position Call as a Waypoint
When a position is received from another DSC radio the GX2400 allows the
position to be saved as a waypoint.
Refer to section “11.7.4 Saving the Reported Position as a Waypoint” for details.
12.1.3 Selecting the Display Range

This menu item allows setting of the range on the compass display.
1. Press & hold [ ]  “WAYPOINT SETUP”  “DISPLAY RANGE”
2. Rotate the DIAL/ENT knob to select desired range. (Unit

of measure depends on the settings in the GPS SETUP
menu. Refer to section “19.7 UNITS OF MEASURE”.)
12.1.4 Selecting the Arrival Range
This menu setting determines the arrival range distance. An alert will sound when
your vessel navigates to within the arrival range of the designated waypoint.
1. Press & hold [ ]  “WAYPOINT SETUP”  “ARRIVAL RANGE”
2. Rotate the DIAL/ENT knob to select desired range. (Unit

of measure depends on the settings in the GPS SETUP
menu. Refer to section “19.7 UNITS OF MEASURE”.)
79
12.2 ROUTING OPERATION
The GX2400 permits setting 1 to 30 waypoints along the route to a destination.
Via29
Via3
Via30
Via2
Current
position Via1
WPT
Routing to a Waypoint
12.2.1 Setting Up Routing Directory

NOTE
All the destinations and via-points must be programmed as waypoints in the
memory. Refer to section “12.1.2 Setting Up Waypoint Directory”.
Adding a Route
1. Press & hold [ ]  “WAYPOINT SETUP”  “ROUTE DIRECTORY”


4. Enter the route name by rotating the DIAL/ENT knob
and the [SELECT] soft key.
When finished entering the name (using fifteen char-
5. Rotate the DIAL/ENT knob to select “ROUTE
POINTS”, press the [SELECT] soft key.
6. Rotate the DIAL/ENT knob to select “WPT:”, then

8. Rotate the DIAL/ENT knob to select “Via 1:”, then

80
10. Repeat steps 8 and 9 to add more via-points.
11. Press the [BACK] soft key.
press the [ENTER] soft key to store the route into
memory.
Editing a Route
This function allows a previously entered route to be edited.
2. Rotate the DIAL/ENT knob to select “EDIT”, then

3. Rotate the DIAL/ENT knob to select the route to be

edited, then press the [SELECT] soft key to show the
route input display.
4. Perform steps 3 to 11 of the previous page until the
route is updated.
press the [SELECT] soft key to store the edited route
into memory.
Deleting a Route
2. Rotate the DIAL/ENT knob to select “DELETE”, then

3. Rotate the DIAL/ENT knob to select the route to be

deleted, then press the [SELECT] soft key.
4. Confirm the route to be deleted, Rotate the DIAL/

ENT knob to select “OK”, then press the [SELECT]
soft key.
81
12.2.2 Starting and Stopping Route Navigation
1. [ ]  “NAVI”  “ROUTE”

category (“HISTORY” or “MEMORY”), then press the
[SELECT] soft key.
3. Rotate the DIAL/ENT knob to select a route, then
press the [SELECT] soft key. The navigation screen
with “RTE” indicator appears.
4. A message “ARRIVED” will appear when the first
target point is reached.
To start navigation to the next target, press the [YES]
soft key.
12.2.3 Changing the Destination

1. On the navigation screen, press one of the soft keys,
then press the [NEXT TG] soft key.

destination, then press the [SELECT] soft key.
3. The navigation screen with the new destination

appears.
12.2.4 Selecting Automatic or Manual Routing

When your vessel arrives at a via waypoint, this setting determines whether
or not navigation to the next waypoint will continue automatically or must be
initiated manually.
1. Press & hold [ ]  “WAYPOINT SETUP”  “ROUTING OPERATION”

“MANUAL”, then press the [ENTER] soft key.
82
13 GM OPERATION
The GM (Group Monitor) feature of the GX2400 utilizes the same system as
the DSC Group call and Auto Position Polling, to display the group members'
locations.
13.1 SETTING UP GM OPERATION

The transceiver is capable of storing up to 10 groups with 1 to 9 members each.
13.1.1 Setting Up GM Group Directory

NOTE
• For this function to operate, the same group MMSI must be programmed
into the transceivers of all the group members to be monitored. Refer to
section “11.5.1 Setting up a Group Call” for details.
• Group members for GM operation can only be selected from the Individual/
Position Call directory, therefore for all members that you want to monitor,
must be stored in the directory. Refer to section “11.4.1 Setting up the
Individual / Position Call Directory” for details.
1. Press & hold [ ]  “GM SETUP”  “GM GROUP DIRECTORY”


4. Enter the route name by rotating the DIAL/ENT knob
and the [SELECT] soft key.
When finished entering the name (using eleven char-
5. Rotate the DIAL/ENT knob to select “GM ID:”, press
the [SELECT] soft key, then enter the group MMSI
number.
When finished entering the MMSI, press the [FINISH]
soft key.
6. Rotate the DIAL/ENT knob to select “MEMBER”, then
83
7. Rotate the DIAL/ENT knob to select a directory list
number, then press the [SELECT] soft key.
8. Rotate the DIAL/ENT knob to select a member from

the Individual directory, then press the [SELECT] soft
key.
9. Repeat steps 8 to add members to the group, then
press the [BACK] soft key.
10. Press the [BACK] soft key to return to the “NAME:”
and “GM ID:” screen.
11. Rotate the DIAL/ENT knob to select “SAVE” to store

the data, then press the [ENTER] soft key.
12. To enter another group directory, repeat steps 2
through 11.
13.1.2 Setting Up the Polling Time Interval
1. Press & hold [ ]  “GM SETUP”  “INTERVAL”
2. Rotate the DIAL/ENT knob to select the desired poll-

ing interval time, then press the [ENTER] soft key.
13.1.3 Enabling/Disabling Transmission during GM Operation
1. Press & hold [ ]  “GM SETUP”  “GM TX”
2 Rotate the DIAL/ENT knob to select the desired

transmission type, then press the [ENTER] soft key.
OFF: Disables the transmission during GM operation.

ON GM: Enables the transmission during the GM target display.
ON ALL: Enables the transmission during the GM operation.
84
13.2 STARTING GM OPERATION
NOTE
To start GM operation, configure the GM Group Directory setting in setup
menu. Otherwise, you cannot start the GM operation. Refer to section “13.1.1
Setting Up GM Group Directory” for details.
1. [ ]  “GM”
2. Rotate the DIAL/ENT knob to select a group you want

to monitor, then press the [SELECT] soft key.
The GM operation begins, and the GM target display

appears.
13.2.1 Changing the GM Group Being Monitored

1. On the GM target display, press one of the soft keys,
then press the [TG LIST] soft key.
2. Press the [CHG GRP] soft key.
3. Rotate the DIAL/ENT knob to select the name of the

group you want to monitor, then press the [SELECT]
soft key.
The GM group being monitored changes. The GM
target display appears.
85
13.2.2 Transmitting a DSC Call to a Group Member
1. On the GM target display, press one of the soft keys,
then press the [TG LIST] soft key.
2. Rotate the DIAL/ENT knob to select a member you

want to call.
3. Press the [SELECT] soft key to display the location,
distance, and bearing of the selected member.
4. Press the [CALL] soft key to transmit a DSC Individual
call to the selected member.
13.2.3 Starting Navigation to a Group Member

1. On the GM target display, press one of the soft keys
to show the key selections.
2. Press the [TG LIST] soft key.
3. Rotate the DIAL/ENT knob to select a member you
want to approach.
4. Press the [SELECT] soft key to display the location,
distance, and bearing of the selected member.
5. Press the [TO WPT] soft key to start navigation to the
selected member. (Press the [BACK] soft key twice
to cancel and return to the GM target display.)
86
14 AUTOMATIC IDENTIFICATION SYSTEM (AIS)
14.1 GENERAL
NOTE
The GX2400 does not require a special marine VHF antenna to receive AIS
transmissions. The GX2400 does not transmit AIS signals, it is NOT recom-
mended to use an antenna dedicated for AIS operation.
The Automatic Identification System (AIS) is a short range coastal tracking

system. AIS is intended to assist in collision avoidance by seeing positions and
courses of AIS equipped vessels around your vessel.
AIS is mandatory on passenger ships, irrespective of size, all ships 300 gross
tonnage and larger engaged on international voyages, cargo ships of 500 gross
tonnage and larger not engaged on international voyages.
AIS uses two marine VHF channels. Each ship equipped with an AIS transpon-
der transmits a packet every few seconds with information about the ship and
its voyage. Radio frequencies: AIS1 = 161.975 MHz and AIS2 = 162.025 MHz.
A stand-alone AIS receiver or the AIS receiver built in to a Class A or Class B
transponder can pick up these radio signals and translate them into a NMEA
data sentence that can be understood by a computer with the proper software
or by an AIS-enabled chart plotter.
Classes of AIS:
Class A - 12.5W power output - mandated for use on SOLAS Chapter V vessels
(and others in some countries).
Class B CS - 2W output - lower cost derivative for leisure and non-SOLAS markets.
The GX2400 is capable of receiving Class A and Class B CS transmissions with
the internal Dual Channel AIS receiver.
14.2 AIS OPERATION

The GX2400 is equipped with an AIS receiver and can display AIS targets
around your vessel on the radio's display. Therefore, you can identify and avoid
in proximity to your vessel.
NOTE
To show AIS targets on the radio’s display, the internal or external GPS
needs to be fixed own location so the radio knows its position relative to the
AIS targets.
1. [ ]  “AIS”
87
The AIS display shows your vessel as a “ ” icon in Vessel Location
the center of the display. AIS targets are shown as

triangles. The line projected from the circle is the AIS
vessels course over ground (COG).
Range Ring AIS Target

Selected AIS Target
2. Rotate the DIAL/ENT knob to change the AIS target.
Rotating the DIAL/ENT knob counterclockwise
sequentially displays AIS vessels in order closest to
your ship. Rotating the DIAL/ENT knob clockwise
sequentially displays AIS vessels in order furthest
Information
from your ship. of the AIS Target
The selected AIS target is displayed with “ ” icon,
while other stations are displayed with “ ” icon.
NOTE: Up to 15 AIS targets can be shown on the display. All received AIS targets
are displayed on the compatible chart plotter or navigation software via NMEA 0183
or NMEA 2000.
14.2.1 Displaying the AIS Target Information Screen
1. On the AIS screen, press one of the soft keys to show
the key selections. These selections are described
below:
[RANGE]: Press this key to change the display range
of the screen.
[TG LIST]: P ress this key to show a list of the MMSI
numbers or the vessel names being
received.
[FUNC]: Press this key to show the function menu.
2. Press the [TG LIST] soft key to show a list of AIS target being received.
3. Rotate the DIAL/ENT knob to select the MMSI number
(or vessel name). then press the [SELECT] soft key.
Pressing the [DANGER] soft key changes the order
to the TCPA time order.
4. The AIS target information screen appears. To see
more information of the AIS target, rotate the DIAL/
ENT knob. Press the [BACK] key to return to a list of
AIS target.
5. Press the [EXIT] key to return to radio operation.
88
14.2.2 Changing the AIS Range
the key selections.
2. Press the [RANGE] soft key. Press the soft keys at
the center and right side to select the radius range to
display on the AIS screen.
3. Press the [BACK] soft key to return to AIS screen.
NOTE
You may change the display range unit of the AIS screen, refer to section
“19.7 UNITS OF MEASURE”.
14.2.3 Transmitting an Individual Call to an AIS Ship

It is possible for the GX2400 to transmit a DSC individual call to a received AIS
target by the procedure below:

the key selections.
2. Press the [TG LIST] soft key to show a list of AIS
target being received.
3. Rotate the DIAL/ENT knob to select the MMSI number
(or vessel name). then press the [SELECT] soft key.
4. Press the [CALL] soft key

6. To transmit an individual DSC call to the select AIS
ship, press the [YES] soft key.
89
After the GX2400 transmits, the radio waits for the
DSC radio on the AIS ship to transmit a reply, at which
time the radio will ring like a telephone. Pick up the
microphone, press the PTT switch and talk to the AIS
vessel.
7. Press the [QUIT] soft key to return to AIS screen.
14.2.4 CPA/TCPA Alarm Functions

The CPA (Closest Point of Approach) alarm sounds when other AIS vessels
enter within the range set as the CPA Limit. For details, refer to section “14.3.1
CPA”.
The TCPA (Time to Closest Point of Approach) alarm sounds according to the
time set as the TCPA Limit which is the time taken until other AIS vessels enter
within the range set as the CPA Limit. For details, refer to section “14.3.2 TCPA”.
1. If other AIS vessels approach your ship, the alarm

sounds according to the CPA Limit and TCPA Limit
that you set in advance.
The targets for the CPA/TCPA alarm will appear with
“ ” and flash.
Up to 15 targets for the CPA/TCPA alarm can be shown on the screen.
NOTE: If the display is in a mode other than AIS, the radio automatically switches
to the AIS mode.
3. On the display you will notice 3 soft key selections.
[INFO]: Pressing this key shows the information
screen of the CPA/TCPA alarm targets.
[CALL]: Pressing this key switches the screen to the
setting screen for transmitting individual DSC
calls.
[EXIT]: Press this key to return to AIS screen.
4. To transmit individual calls to the CPA/TCPA alarm targets, follow steps
4 through 8 in “14.2.3 Transmitting an Individual Call to an AIS Ship”
90
14.2.5 Changing the Compass Display
The compass display can be switched between “COURSE-UP” and “NORTH-
UP”. The default setting is “COURSE-UP”.
Refer to section “19.2 COMPASS DIRECTION” for details.
14.3 AIS SETUP

14.3.1 CPA
This function allows you to set the CPA (Closest Point of Approach) alarm distance.
: CPA means the positions at which two moving vessels reach their closest
possible distance.
1. Press & hold [ ]  “AIS SETUP”  “CPA”
2. Rotate the DIAL/ENT knob to select the distance you

want the radio to alert you of an approaching AIS
equipped vessel. You can select one from “0.1nm”
to “20nm” (“1nm” is default).
setting.
14.3.2 TCPA
This function allows you to set the TCPA (Time to Closest Point of Approach)
alarm.
: Setting up a TCPA alarm sets a time point where the radio will alarm when
an AIS equipped vessel approaching is within the time selected.
1. Press & hold [ ]  “AIS SETUP”  “TCPA”
2. Rotate the DIAL/ENT knob to select the time you want

the radio to alert you of an approaching AIS equipped
vessel. The time can be set from “1min” to “60min”
(“10min” is default).
setting.
91
14.3.3 CPA/TCPA Alarm
Enable/disable the CPA/TCPA alarm functions. The default setting is “OFF”.
1. Press & hold [ ]  “AIS SETUP”  “CPA/TCPA ALARM”
2. Rotate the DIAL/ENT knob to select “CPA” or “TCPA”,


setting.
NOTE
The alarm will sound until it is disabled (1) by pressing any key, (2) following
the steps above and selecting “OFF” in step 3, or (3) when the ship is out of
the selected CPA/TCPA alarm range. The alarm is produced from the front
panel speaker, the speaker in the microphone, the optional external speaker
and optional RAM4 and RAM4X microphone when connected.
14.3.4 IGNORE VESSELS

This function allows listed registered AIS vessels to be ignored by the CPA /
TCPA alarm function.
1. Press & hold [ ]  “AIS SETUP”  “CPA/TCPA ALARM”
2. Rotate the DIAL/ENT knob to select “IGNORE

VESSELS”, then press the [SELECT] soft key.


92
5. Press the [◄] or [►] key to select the letters of the
name of the vessel or person you want to reference
in the ignore vessel.
7. Repeat steps 5 and 6 until the name is complete.
The name can consist of up to eleven characters, and if you do not use all
fifteen characters, select “→” to move to the next space. This method can
also be used to enter a blank space in the name.
If a mistake was made entering in the MMSI number, press the [◄] or
[►] key to select “←” or “→”, press the [SELECT] soft key until the wrong
8. When finished entering the name (using eleven characters or less), press
the [FINISH] soft key to advance to the MMSI number entry.
9. Rotate the DIAL/ENT knob to select “MMSI:”, then
10. Press the [◄] or [►] key to select numbers, 0 - 9. To

enter the desired number and move one space to the
right by pressing the [SELECT] soft key. Repeat this
procedure until all nine space of the MMSI number are
entered.
If a mistake was made entering in the MMSI number, press the [◄] or
[►] key to select “←” or “→”, press the [SELECT] soft key until the wrong
11. When the MMSI number is entered, press the [FINISH] soft key.
12. To store the entered data, rotate the DIAL/ENT knob
to select “SAVE”, then press the [SELECT] soft key.
13. To enter another AIS vessel, repeat steps 3 through 12.
93
15 NMEA 2000 SETUP
Set the device numbers and system numbers of devices connected to the
NMEA 2000 network.
15.1 SELECT DEVICE

Select the device for which you want to set the device number and system number.
1. Press & hold [ ]  “NMEA2000 SETUP”  “SELECT DEVICE”
2. In the SELECT DEVICE list, rotate the DIAL/ENT

knob to select the external device for which the device
number and the system number are to be set.
3. Press the [SELECT] soft key to store the selected setting.
NOTE
If any devices connected to the network are not displayed in the list, press
the [SEARCH] soft key to update the list.
15.2 DEVICE NUMBER

If connecting two or more the GX2400 series, change the device number of
either one. Set the device number of the device selected in “15.1 SELECT
DEVICE”.
1. Press & hold [ ]  “NMEA2000 SETUP”  “DEVICE NUMBER”
2. Rotate the DIAL/ENT knob to select the first digit of

the device number, then press the [SELECT] soft key
to step to the next number.
3. Repeat step 2 to set the device number within the
range of 000 to 251. (“000” is default).
4. If a mistake is made entering in the device number, press the [◄] or [►]
character is selected, and perform step 2.
5. When finished programming the device number, press
the [FINISH] soft key.
94
15.3 SYSTEM NUMBER
Set the system number of the device selected in “15.1 SELECT DEVICE”.
1. Press & hold [ ]  “NMEA2000 SETUP”  “SYSTEM NUMBER”
2. Press the [◄] or [►] key to select the first digit of the
system number, then press the [SELECT] soft key to
step to the next number.
3. Repeat step 2 to set the system number within the
range of 00 to 15. (“00” is default).
4. If a mistake is made entering in the system number, press the [◄] or [►]
5. When finished programming the system number,
press the [FINISH] soft key.
15.4 SUMMARY OF THE NMEA 2000 SETUP

Item Description Default Value Page
Select the device for which you want
SELECT DEVICE to set the device number or the − 94
system number
DEVICE NUMBER Set the device number 000 94
SYSTEM NUMBER Set the system number 00 95
15.5 COMPATIBLE NMEA 2000 PGN LIST

Receive Transmit
059392 ISO Acknowledgement 059392 ISO Acknowledgement
059904 ISO Request 059904 ISO Request
060928 ISO Address Claim 060928 ISO Address Claim
065240 ISO Commanded Address − −
126464 Receive/Transmit PGN's group 126464 Receive/Transmit PGN's group
function function
126993 Heartbeat 126993 Heartbeat
126996 Product Information 126996 Product Information
127237 Heading/Track Control − −
127250 Vessel Heading − −
127258 Magnetic Variation − −
128259 Speed − −
129025 Position, Rapid Update − −
129026 COG and SOG, Rapid Update − −
129029 GNSS Position Data 129029 GNSS Position Data
129033 Local Time Offset − −
95
Receive Transmit
− − 129038 AIS Class A Position Report
− − 129039 AIS Class B Position Report
129040 AIS Class B Extended Position
− −
Report
129041 AIS Aids to Navigation (AtoN)
− −
Report
129793 AIS UTC and Date Report (Base
− −
Station)
129794 AIS Class A Static and Voyage
− −
Related Data
− − 129796 AIS Acknowledge
− − 129797 AIS Binary Broadcast Message
− − 129798 AIS SAR Aircraft Position Report
− − 129799 Radio Frequency/Mode/Power
129801 AIS Addressed Safety Related
− −
Message
129802 AIS Safety Related Broadcast
− −
Message
− − 129808 DSC Call Information
129809 AIS Class B “CS” Static Data
− −
Report, Part A
129810 AIS Class B “CS” Static Data
− −
Report, Part B
129540 GNSS Sats in View 129540 GNSS Sats in View
96
16 CONFIGURATION SETUP
16.1 DISPLAY MODE
The display mode can be selected according to the time of day you operate
the radio.
1. Press & hold [ ]  “CONFIGURATION”  “DISPLAY MODE”

setting. Select the “DAY MODE” or “NIGHT MODE”
setting.
DAY MODE: Normal display mode.
NIGHT MODE: Low brightness display mode for night
use.
16.2 DIMMER ADJUSTMENT

This menu selection adjusts the backlight intensity.
1. Press & hold [ ]  “CONFIGURATION”  “DIMMER”
2. Rotate the DIAL/ENT knob to select the desired level

(“7” is default). When “OFF” is selected, the lamp is
turned OFF.
3. Press the [ENTER] soft key to store the selected level.
16.3 DISPLAY CONTRAST

The display contrast can be adjusted to suit your operation environment.
1. Press & hold [ ]  “CONFIGURATION”  “CONTRAST”
2. Rotate the DIAL/ENT knob to select the desired level.

The contrast level can be set from “1” to “30” (“15” is
default).
97
16.4 KEY BEEP
This selection is used to select the beep tone volume level when a key is pressed.
1. Press & hold [ ]  “CONFIGURATION”  “KEY BEEP”
2. Rotate the DIAL/ENT knob to select the desired level.

The beep level can be set from “1” to “7”, or “OFF”
(“4” is default).
16.5 FOG ALERT TONE FREQUENCY
The function allows the radio to be setup to send the proper fog frequency
which is dependent on vessel size, shown below:
70 - 200Hz: Vessel that are 660 feet (200 meters) or more in length
130 - 350Hz: Vessel that are 247.5 feet (75 meters) or more but less than
660 feet (200 meters) in length
250 - 700Hz: Vessel that are 66 feet (20 meters) or more but less than
247.5 feet (75 meters) in length
250 - 700Hz: Vessel that are 39.6 feet (12 meters) or more but less than
66 feet (20 meters) in length
1. Press & hold [ ]  “CONFIGURATION”  “FOG FREQUENCY”

level. The frequency level can be set from “200Hz”
to “850Hz” (“400Hz” is default).
setting.
NOTE
By default, the radio Fog frequency is set to 400 Hz. In most cases this
frequency should not be changed unless the vessel is very large.
98
16.6 LISTEN BACK
While in PA, FOG HORN, or HORN mode, toggle the listen back function
between ON and OFF.
1. Press & hold [ ]  “CONFIGURATION”  “LISTEN BACK”
2. Rotate the DIAL/ENT knob to select “OFF” or “ON”

(“ON” is default).
setting.
16.7 STATION NAME

This function allows you to change the name of the radio or second station
microphone.
1. Press & hold [ ]  “CONFIGURATION”  “STATION NAME”
2. With the second station microphone connected, rotate

the DIAL/ENT knob to select the unit to be named,
3. Rotate the DIAL/ENT knob to select to scroll through
the first letter of the new station name.
5. Repeat steps 3 and 4 until the name is complete. The
name can consist of up to ten characters, and if you
do not use all ten characters, select “→” to move to
the next space. This method can also be used to enter
a blank space in the name.
If a mistake was made entering in the station name, rotate the DIAL/ENT
knob to select “←” or “→”, press the [SELECT] soft key until the wrong
6. When finished entering the station name (using ten characters or less),
press the [FINISH] soft key to advance to the second station name entry.
7. Rotate the DIAL/ENT knob to select “SSM-70H”, then
8. Rotate the DIAL/ENT knob to select to scroll through
the first letter of the new station name.
99
10. Repeat steps 8 and 9 until the name is complete. The name can consist
of up to ten characters, and if you do not use all ten characters, select “→”
to move to the next space. This method can also be used to enter a blank
space in the name.
If a mistake was made entering in the station name, rotate the DIAL/ENT
knob to select “←” or “→”, press the [SELECT] soft key until the wrong
11. When finished entering the station name (using ten characters or less),
press the [FINISH] soft key.
16.8 SOFT KEYS

From this menu, you can assign desired functions to each soft key from numbers
01 to 12. You can also set how long the soft key icon will be displayed after the
corresponding soft key is pressed.
16.8.1 Key Assignment
1. Press & hold [ ]  “CONFIGURATION”  “SOFT KEY”
2. Rotate the DIAL/ENT knob to select “KEY ASSIGN-

MENT”, then press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select the key number

to be programmed, and press the [SELECT] soft key.
4. Rotate the DIAL/ENT knob to select a new function to

be assigned, and press the [ENTER] soft key. Avail-
able functions are listed below. By selecting “NONE”
the soft key assignment is removed.
5. Repeat steps 3 and 4 to program other soft keys.
The VHF radio functions can be assigned to a maximum of 12 soft keys.
100
SOFT KEY
DISPLAY FUNCTION
ICON
NONE − −
TX HI/LO Selects transmit power
WX/CH Switches channels between weather and marine
SCAN Turns the scanning function ON or OFF
MULTI WATCH Starts and stops dual watch or triple watch scan
MARK POSITION Marks the current position for a “Waypoint”
Add or remove channels from memory channel

SCAN MEMORY scan
PRESET Programs or deletes the preset memory channel
MAN OVERBOARD Marks the position where a person falls overboard
NOISE CANCEL Enables the noise canceling settings display
CH NAME Edit channel names
SCRAMBLER Configures the secret communication settings.
COMPASS Enables the “Compass” display
Enables the “Waypoint” or “Route” navigation

NAVIGATION display
FOG HORN Select FOG HORN mode
Activates intercom between radio and RAM4

INTERCOM microphone (optional SSM-70H (RAM4) or SSM-
72H (RAM4X) required)
GPS LOGGER Starts and stops logging position data
AIS DISPLAY Shows the “AIS” display
HORN BUTTON Activates the Fog Horn function
PUBLIC ADDRESS Switches channels between weather and marine
RX SENSE Toggles between LOCAL and DISTANCE
Switches the display between daytime and

DISPLAY MODE nighttime mode
101
16.8.2 Key Timer
1. Press & hold [ ]  “CONFIGURATION”  “SOFT KEY”
2. Rotate the DIAL/ENT knob to select “KEY TIMER”,

3. Rotate the DIAL/ENT knob to select the desired time,

default is 10 seconds.
16.9 RESET
The memory and the setup categories may be reset independently, or the
transceiver may be reset to the original factory settings.
1. Press & hold [ ]  “CONFIGURATION”  “RESET”
2. Rotate the DIAL/ENT knob to select the desired cate-

gory from: “DSC/GM SETUP”, “WAYPOINT SETUP”,
“CHANNEL SETUP”, “GPS SETUP”, “CONFIGURA-
TION”, “FACTORY” (all settings*1 except the “MMSI”
and “ATIS”*2 will be initialized), “USER MMSI”, or
“ATIS CODE”*2.
*1(The Individual Directory is also cleared.)
*2(GX2400GPS/E only)
For details on resetting “USER MMSI” and “ATIS CODE”, refer to “16.9.1 Reset
the USER MMSI and ATIS CODE”.
soft key.)

102
16.9.1 Reset the USER MMSI and ATIS CODE
If the MMSI number and ATIS* code need to be reset. Please contact Standard
Horizon to obtain the required reset codes.
*(GX2400GPS/E only)
To request the Reset Code
Contact Standard Horizon and confirm the following required information.
● The Information Necessary to obtain the Reset Code:
• Model name
• Serial number
• Current MMSI number and/or ATIS code
(To check the MMSI number and ATIS code, refer to “8.6.1 Maritime
Mobile Service Identity (MMSI)” or “20 ATIS SETUP”.
• Request codes for the MMSI number and/or the ATIS code
(See “ Checking the Request code” below).
● Contact Information
USA/Canada
E-mail: marinetech@yaesu.com
Telephone: (800) 767-2450
Europe
E-mail: service@yaesu.co.uk
Telephone: +44 (0)1962 866667
Checking the Request code
1. Press & hold [ ]  “CONFIGURATION”  “RESET”

category. You can select either “USER MMSI”, or
“ATIS CODE”*, then press the [SELECT] soft key.
*(GX2400GPS/E only)
3. Press the [SELECT] soft key again.

The request code will be displayed.
NOTE
When resetting both “USER MMSI” and “ATIS CODE”, both request codes
are required.
103
Resetting the USER MMSI and ATIS codes
Here is the procedure for resetting the USER MMSI and ATIS codes after
obtaining the reset codes.
1. The RESET screen is displayed on step 2 in “ Check-
ing the Request code”.
2. Rotate the DIAL/ENT knob to select “PASSWORD",
The password input screen will appear.
3. Press the [◄] or [►] key to select the first digit of the
reset password, then press the [SELECT] soft key to
step to the next number.
4. Repeat steps 3 until the reset password is complete.
If a mistake is made entering in the station name,
5. Press the [FINISH] soft key.
If the reset is successful, “Completed!” will appear
on the screen.
If the error message is displayed, input the reset
code again.
6. Press the [OK] soft key to return to the setup screen.
NOTE
The acquired reset password is available only one time.
104
16.10 SUMMARY OF THE CONFIGURATION SETUP
Toggles LCD display mode between
DISPLAY MODE DAY MODE 97
daytime and nighttime mode
Adjusts the backlight level of the
DIMMER 7 97
LCD and keypad
CONTRAST Adjusts the contrast of the LCD 15 97
Adjusts the volume of beep tone
KEY BEEP 4 98
when a key is pressed
FOG ALERT TONE Sets the tone frequency of the fog
FREQUENCY 400Hz 98
horn
LISTEN BACK Turns on or off of listen back function ON 99
Sets the names of the radio and
STATION NAME − 99
external devices
SOFT KEY
KEY ASSIGNMENT Sets the assignment of the soft keys − 100
KEY TIMER Sets the display time of the soft keys 10 sec 102
RESET Initializes the memories and settings − 102
105
17 CHANNEL FUNCTION SETUP
17.1 CHANNEL GROUP
This menu item allows you to selection of a channel group from USA, Canada*,
and International. Refer to section “9.7 CHANNEL GROUP” for details.
17.2 WEATHER ALERT (USA version only)

Enables/disables the NOAA Weather Alert function. The default setting is “ON”.
1. Press & hold [ ]  “CHANNEL SETUP”  “WX ALERT”
2. Rotate the DIAL/ENT knob to select “ON” or “OFF”.

17.3 SCAN MEMORY

To be able to scan channels the scan memory must be programmed. This
section designates channels to be stored into scan memory.
Refer to section “9.10.2 Programming Scan Memory” for details.
17.4 SCAN TYPE

This selection is used to select the scan mode between “MEMORY” and
“PRIORITY”. The default setting is “PRIORITY”.
Refer to section “9.10.1 Selecting Scan Type” for details.
17.5 SCAN RESUME

This selection is used to set the time after a transmission ends before the radio
starts to scan channels again. The default setting is 3 seconds.
1. Press & hold [ ]  “CHANNEL SETUP”  “SCAN RESUME”

resume time, default is 3 seconds. The resume time
can be set to “1sec” through “5sec”.
3. Press the [ENTER] soft key to store the new setting.
17.6 MULTI WATCH
This selection is used to select the watch type between “DUAL” and “TRIPLE”.
The default setting is “DUAL”.
Refer to section “9.9 MULTI WATCH (TO PRIORITY CHANNEL)” for details.
106
17.7 PRIORITY CHANNEL
This procedure permits setting a different priority channel to be used when
priority scanning. By default, the priority channel is set to Channel 16.
1. Press & hold [ ]  “CHANNEL SETUP”  “PRIORITY CHANNEL”

nel to be a priority.
17.8 SUB CHANNEL

By default, the sub channel is set to Channel 9. This procedure permits assign-
ing a different sub channel for instant access.
1. Press & hold [ ]  “CHANNEL SETUP”  “SUB CHANNEL”

nel to be a sub channel.
17.9 CHANNEL NAME

When the radio (“Normal”) mode is selected, the display will show a name
under the channel number. This name describes the use of the channel. The
name may be customized the with the below procedure.
Example: CH69 PLEASURE to HOOKUP
1. Press & hold [ ]  “CHANNEL SETUP”  “CHANNEL NAME”

be named, then press the [SELECT] soft key.
3. Press the [◄] or [►] key to select the first letter of the
new channel name.
4. Press the [SELECT] soft key to store the first letter of
5. Repeat step 3 and 4 until the name is complete. The name can consist of up
to 16 characters, if you do not use all 16 characters, select “→” to move to the
next space. This method can also be used to enter a blank space in the name.
107
If a mistake is made entering the channel name, press the [◄] or [►] key to
select “←” or “→”, press the [SELECT] soft key until the incorrect character
is selected, then perform steps 3 and 4.
6. When finished entering the channel name (using
fifteen characters or less), press the [FINISH] soft
key to save the name.
7. To enter the name of another channel, repeat the
steps 2 through 6.
NOTE
When “CHANNEL NAME” is assigned to a soft key, the channel name may
be displayed directly by pressing the [NAME] soft key during radio operation.
17.10 RX LED DIMMER ADJUSTMENT

This menu selection adjusts the RX LED intensity.
1. Press & hold [ ]  “CHANNEL SETUP”  “RX LED DIMMER”
2. Rotate the DIAL/ENT knob to select the desired level

(“7” is default). When “OFF” is selected, the lamp is
turned OFF.
17.11 NOISE CANCELLATION

Enables/disables the Noise-canceling function of the transmitter and receiver
independently.
1. Press & hold [ ]  “CHANNEL SETUP”  “NOISE CANCEL”
2. Rotate the DIAL/ENT knob to select “TX MODE”, then

3. Rotate the DIAL/ENT knob to select “ON” or “OFF”,

then press the [ENTER] soft key.
108
4. Rotate the DIAL/ENT knob to select “RX MODE”, then
5. Rotate the DIAL/ENT knob to select the noise level
from “LEVEL1” through “LEVEL4” or “OFF”, then
17.12 AUDIO FILTER OPERATION

This menu item allows you to select operation of the internal audio filter for
the best acoustics in noisy environments. The default setting is “NORMAL”.
1. Press & hold [ ]  “CHANNEL SETUP”  “AF PITCH CONTROL”
2. Rotate the DIAL/ENT knob to select the desired filter

operation.
17.13 SCRAMBLER SETUP

The voice scrambler function may only be enabled by your dealer.
Configure the voice scrambler setting. Two types of voice scrambler functions
are available: the 4-code type (CVS2500A compatible) and the 32-code type
(FVP-42 compatible for Furuno Electric FM-4721).
NOTE
• The voice scrambler function is not available with the factory default
settings. Please contact your dealer to activate the voice scrambler function.
• This function is not available for CH16 and CH70.
1. Press & hold [ ]  “CHANNEL SETUP”  “SCRAMBLER”
2. Rotate the DIAL/ENT knob to select “TYPE”, then

3. Rotate the DIAL/ENT knob to select “CVS2500” or

“FVP-42”, then press the [ENTER] soft key.
NOTE: Changing this setting will delete all scrambler codes
set for each channel.
109
4. Rotate the DIAL/ENT knob to select “CODE”, then

be scrambled, then press the [SELECT] soft key.
NOTE: CH16 and CH70 cannot be used.
6. Rotate the DIAL/ENT knob to select the scrambler

code. The scrambler code can be set from “00” to
“03” or “OFF” (While FVP-42 is selected in step 3,
the scrambler code can be set from “00” to “31” or
“OFF”). When “OFF” is selected the voice scrambler
is disabled.
7. Press the [ENTER] soft key to store the selected code.
8. Repeat steps 5 through 7 to set other channels.
17.14 SUMMARY OF THE CANNEL FUNCTION SETUP

CHANNEL GROUP Selects the channel group (Depending on the 31
transceiver version)
WEATHER ALERT Turns the Weather Alert Function OFF 106
(USA version only) ON or OFF
SCAN MEMORY Add or remove a channel from − 34
Scan Memory
SCAN TYPE Select priority scan or memory PRIORITY 34
scan
SCAN RESUME Sets the resume time of scanning 3 sec 106
MULTI WATCH Selects Dual Watch or Triple DUAL 33
Watch
PRIORITY CHANNEL Selects a priority channel CH16 107
SUB CHANNEL Selects a Sub Channel CH09 107
CHANNEL NAME Edit the name of memory channels − 107
RX LED DIMMER Adjusts the RX LED dimmer level 7 108
NOISE CANCEL Turns on or off of noise cancelling OFF 108
function (independently available
for transmission and reception)
AF PITCH CONTROL Selects the audio filter operation NORMAL 109
SCRAMBLER* Configures the secret communi- TYPE: CVS2500 109
cation settings CORD: −
*(The voice scrambler function is not available with the factory default settings. Please
contact your dealer to activate the voice scrambler function.)
110
18 DSC SETUP
18.1 INDIVIDUAL DIRECTORY
The GX2400 has a DSC directory that allows you to store a vessel or person’s
name, and the associated MMSI that you may wish to contact via individual
calls, position requests and position report transmissions.
To transmit an individual call, program this directory with the information of the
vessel you wish to contact, similar to a cellular phone's contact list.
Refer to section “11.4.1 Setting up the Individual / Position Call Directory”
for details.
18.2 INDIVIDUAL REPLY

This menu item sets the radio to automatically (default setting) or manually
respond to a DSC Individual call requesting you to switch to a working channel
for voice communications. When “MANUAL” is selected, the MMSI of the call-
ing vessel is shown allowing you to see who is calling. This function is similar
to caller ID on a cellular phone.
Refer to section “11.4.2 Setting up the Individual Call Reply” for details.
18.3 INDIVIDUAL ACKNOWLEDGMENT

The radio can be setup to transmit a reply automatically (default), or set so the
radio will not reply to an individual DSC call.
Refer to section “11.4.3 Enabling the Individual Call Acknowledgment” for
details.
18.4 INDIVIDUAL RINGER

The radio can be setup to ring like a telephone to alert you that the radio has
received a DSC individual call. The default ring time setting is 2 minutes,
however this can be changed to 5, 10 or 15 seconds with the procedure below.
Refer to section “11.4.6 Setting up the Individual Call Ringer” for details.
18.5 GROUP DIRECTORY

For this function to operate, the same group MMSI must be programmed into all
the DSC VHF radios within the group of vessels that will be using this feature.
Refer to section “11.5.1 Setting up a Group Call” for details.
111
18.6 POSITION REPLY
The GX2400 can be set up to automatically (default setting) or manually send
your position when requested by another vessel. This selection is important if
you are concerned about someone polling the position of your vessel that you
may not want to. In the manual mode you will see the MMSI (Maritime Mobile
Service Identity Number) or persons name, shown on the display allowing you
to choose whether or not to send your position to the requesting vessel.
Refer to section “11.6.1 Setting up a Position Request Reply” for details.
18.7 AUTO POSITION POLLING

The GX2400 has the capability to automatically poll and track seven vessels
programmed into the individual directory.
Refer to section “11.8 AUTO POSITION POLLING” for details.
18.8 AUTO POSITION INTERVAL

The time interval between automatic position polling request transmissions
may be selected.
Refer to section “11.8.2 Setting up the Polling Time Interval” for details.
18.9 AUTO CHANNEL CHANGE

When a DSC distress call, or an all ships (urgency or safety) call is received,
the GX2400 will automatically switch to Channel 16.
The automatic switch time may be changed. The default selection is 30 seconds.
1. Press & hold [ ]  “DSC SETUP”  “AUTO CHANNEL CHANGE”

When “OFF” is selected, the “ ” icon will light up on the
screen.
112
18.10 NO ACTION TIMER
If no key is pressed during the “MENU” or “DSC CALL” screen, the transceiver
will automatically return to radio operation.
The default selection is 10 minutes.
1. Press & hold [ ]  “DSC SETUP”  “NO ACTION TIMER”

18.11 WAIT TIME FOR POSITION FIX

This menu allows you to select the maximum wait time till obtaining position
information when receiving a distress call, POS Report call, or acknowledge-
ment to POS request call.
The default selection is OFF.
1. Press & hold [ ]  “DSC SETUP”  “POS UNFIX WAITING TIME”

18.12 DSC BEEP

This feature allows the alarm beeps to be turned ON or OFF when a DSC call
is received. The DSC calls that can be customized are: individual, group, all
ships, position request, position report, geographical, polling, and DSC test.
Refer to section “11.5.4 Setting up the Group Call Ringer” for details.
113
18.13 SUMMARY OF THE DSC SETUP MENU
INDIVIDUAL Enter or edit addresses used for − 52
DIRECTORY individual call
INDIVIDUAL REPLY Selects a reply to an individual MANUAL 53
call
INDIVIDUAL ACK. Selects the message to be sent ABLE 54
automatically as an individual call
acknowledgement
INDIVIDUAL RING Selects the ringing time when 2 min 57
an individual call or a position
request is received
GROUP DIRECTORY Enter or edit addresses used for − 58
group calling
POSITION REPLY Selects reply mode when receiv- AUTO 63
ing a position call
AUTO POSITION Selects the AUTO POSITION AUTO POS REPORT 70
POLLING POLLING operation type
AUTO POS INTERVAL Selects the AUTO POSITION 30 sec 70
POLLING transmission interval
AUTO CHANNEL Selects the delay time to auto- 30 sec 112
CHANGE matically move to the requested
channel after receiving a distress
call, All Ship call, or group call
NO ACTION TIMER Selects the delay time before 10 min 113
automatically returning to routine
transceiver operation when no
key is pressed
POS UNFIX WAITING Sets the maximum wait time to OFF 113
TIME obtain position information when
receiving a distress call, POS
Report call, or acknowledgement
to POS request call
DSC BEEP Turns the audible alarm ON or INDIVIDUAL CALL: ON 113
OFF when receiving a DSC call GROUP CALL: ON
ALL SHIPS: ON
POS REQUEST: OFF
POS REPORT: OFF
GEOGRAPHICAL: ON
DSC TEST CALL: OFF
114
19 GPS SETUP
The “GPS Setup” mode allows the parameters for the NMEA2000 or the NMEA
-0183 or the Internal GPS receiver to be customized for your operating requirements.
19.1 ORDER OF PRIORITY

Specify the order of priority of the input devices to be used for obtaining loca-
tion information. The default setting is “NMEA2000”.
1. Press & hold [ ]  “GPS SETUP”  “ORDER OF PRIORITY”
2. Rotate the DIAL/ENT knob to select “NMEA2000” or

“NMEA-0183”, then press the [ENTER] soft key to
save the new setting.
NOTE
The Internal GPS receiver is always set as the lowest priority.
19.2 COMPASS DIRECTION

This menu item selects the compass direction to be shown on the transceiver
display. The default setting is “COURSE-UP”.
1. Press & hold [ ]  “GPS SETUP”  “COMPASS DIRECTION”

compass display to “COURSE-UP” or “NORTH-UP”.
3. Press the [ENTER] soft key to save the new setting.
19.3 LOCATION FORMAT

This menu item selects the coordinate system to be shown on the transceiver
display. The default setting is “ddd°mm.mmmm”.
1. Press & hold [ ]  “GPS SETUP”  “LOCATION FORMAT”
2. Rotate the DIAL/ENT knob to select the desired coor-

dinate system. The location format can be selected
from “ddd°mm.mmmm” and “ddd°mm’ss””.
115
19.4 TIME OFFSET
Sets the local time offset between UTC (Universal Time Coordinated) and local
time shown on the display. The offset is added or subtracted from the time
received from the GPS.
Refer to section “8.8.1 Setting the GPS Time” for details.
19.5 TIME AREA

This menu selection sets the display to show UTC time or local time with the offset.
Refer to section “8.8.2 Setting the Time Area” for details.
19.6 TIME FORMAT

This menu selection sets the display to show time in 12-hour or 24-hour format.
Refer to section “8.8.3 Setting the Time Format” for details.
19.7 UNITS OF MEASURE

This section sets the display units of speed, distance and altitude.
1. Press & hold [ ]  “GPS SETUP”  “UNIT OF MEASURE”
2. Rotate the DIAL/ENT knob to select the item to be

set.
4. Rotate the DIAL/ENT knob to select the unit.
19.8 MAGNETIC VARIATION

This selection permits customization of the GPS COG (Course Over Ground)
indication on the normal and compass pages, and BRG on the waypoint page.
Refer to section “8.8.4 Setting COG to True or Magnetic” for details.
NOTE
Setting to “ON” is effective only when the RMC sentences with magnetic data
are input from external devices such as a GPS chart plotter.
116
19.9 NMEA 0183 IN/OUT
19.9.1 Data Speed
This menu is utilized to set the NMEA 0183 baud rate of the GPS input (Yellow
and Green wires) and DSC output (White and Brown wires). The default setting
is 4800 bps.
When 38400 bps is selected the DSC sentences (DSC & DSE) are output on
the Blue and Gray wires after a DSC distress, position request is received.
1. Press & hold [ ]  “GPS SETUP”  “NMEA 0183 IN/OUT”
2. Rotate the DIAL/ENT knob to select “DATA SPEED”,

3. Rotate the DIAL/ENT knob to select the desired speed

from “4800bps” and “38400bps”.
19.9.2 Output Sentences
This selection is utilized to set the NMEA output sentences of the transceiver.
By default, the “GLL” and the “RMC” sentences are turned “ON”.
1. Press & hold [ ]  “GPS SETUP”  “NMEA 0183 IN/OUT”
2. Rotate the DIAL/ENT knob to select “OUTPUT

SENTENCES”, then press the [SELECT] soft key.

sentence type, then press the [SELECT] soft key.

6. Repeat steps 3 through 5 to set the other sentences.
117
NOTE
• Data output will be performed according to the data acquisition priority

order setting of “ORDER OF PRIORITY”. Refer to section “19.1 ORDER
OF PRIORITY” for details.
• When “UNIT POWER” of “OPTION GPS UNIT” is set to OFF, NMEA sentences
will not be output. (OPTION GPS reception data will be output as is.)
• The output interval of each NMEA sentence depends on the output timing
on the input device. However, sentences which include POS data will be
output at intervals of two seconds or less.
• When all sentences are set to be output, depending on the baud rate, not
all sentences can be output at intervals of one second or less. GSA and
GSV sentences will be output at intervals of around five seconds.
19.10 INTERNAL GPS UNIT

Change the internal GPS receiver settings. (The settings in this section are
also valid when connecting the SCU-38 External GPS Antenna to the internal
GPS receiver.)
19.10.1 Position Data Output

Select the connection device to be used when outputting position data.
1. Press & hold [ ]  “GPS SETUP”  “INTERNAL GPS UNIT”
2. Rotate the DIAL/ENT knob to select “POS DATA

OUTPUT”, then press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select “NMEA 2000” or

“NMEA 0183”, then press the [SELECT] soft key.

118
19.10.2 Pinning
This selection is utilized to enable or disable position updates when the vessel
is not underway. The default setting is “ON”.
2. Rotate the DIAL/ENT knob to select “PINNING”, then


ON: When pinning is turned ON, the transceiver will
not update its position unless the ship’s speed
is over 0.4 knot.
OFF: When the vessel is underway or stopped, the
transceiver continuously updates its position.
This improves accuracy of the position fix.
5. Press the [CLEAR] key to return to routine transceiver
operation.
19.10.3 Differential GPS
This selection enables or disables differential GPS function by SBAS (Satellite
Based Augmentation System) such as WAAS, EGNOS, MSAS and GAGAN.
In some areas (Australia for example), the GPS reception can have problems
enabling the SBAS. The default setting is “ON”.
2. Rotate the DIAL/ENT knob to select “D-GPS”, then


119
19.10.4 Logger Interval
2. Rotate the DIAL/ENT knob to select “LOGGER

INTERVAL”, then press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select the desired time

and press the [ENTER] soft key.
NOTE: Log time for each logger interval setting
15 sec: Aprox. 25 hours
30 sec: Aprox. 50 hours
1 min: Aprox. 100 hours
19.10.5 Log Erase
2. Rotate the DIAL/ENT knob to select “LOG ERASE”,

soft key.)

120
19.11 SUMMARY OF THE GPS SETUP
ORDER OF PRIORITY Sets the priority order of the NMEA-2000 115
connection devices when obtain-
ing position information
COMPASS DIRECTION Selects the compass direction to COURSE-UP 115
be displayed
LOCATION FORMAT Selects the coordinate system to ddd°mm.mmmm 115
be displayed
TIME OFFSET Sets the offset time from UTC 00:00 116
(available only when “LOCAL” is
selected in the item “TIME AREA”)
TIME AREA Selects the time location to be UTC 116
displayed, from UTC or local
TIME FORMAT Selects the time format to be 24hour 116
displayed, 12-hour or 24-hour
(fixed to “24H” when “UTC” is
selected in the item “TIME AREA”)
UNITS OF MEASURE Selects the unit of measure whenSPEED: kts (knots) 116
displaying speed, distance, andDISTANCE:
altitude nm (nautical mile)
ALTITUDE: ft (feet)
MAGNETIC VARIATION Enables/disables the magnetic OFF 116
variation function
NMEA 0183 IN/OUT
DATA SPEED Sets the NMEA 0183 data speed 4800bps 117
OUTPUT SENTENCES Enables/disables NMEA sentences GLL: OFF 117
GGA: OFF
GSA: OFF
GSV: OFF
RMC: OFF
DSC/DSE: OFF
INTERNAL GPS UNIT
POS DATA OUTPUT Selects the connection device NMEA 2000: OFF 118
when outputting position data NMEA-0183: OFF
PINNING Turns on or off GPS position ON 119
updates for vessel not underway
D-GPS Turns SBAS ON or OFF ON 119
LOGGER INTERVAL Selects the interval time of logging 2 min 120
LOG ERASE Erases the log data − 120
121
20 ATIS SETUP
The GX2400GPS/E supports the ATIS (Automatic Transmitter Identification
System) used in Inland waterways in Europe. When enabled ATIS mode
transmits a unique ATIS code each time the PTT switch is released at the end
of a transmission.
Users should check with their local marine regulatory authority in their country
for assistance in obtaining an ATIS code.
WARNING
The ATIS code can be inputted only once, please be careful not to input
the incorrect ATIS code. If the ATIS code needs to be reset, please contact
Standard Horizon to obtain the required reset code. Refer to section “16.9.1
Reset the USER MMSI and ATIS CODE”.
20.1 ATIS CODE PROGRAMMING

1. Press & hold [ ]  “ATIS SETUP”  “ATIS CODE”

your ATIS, then press the [SELECT] soft key to step
to the next number.
3. Repeat step 2 to set the ten digits of the ATIS.
4. If a mistake is made in entering the ATIS, press the [◄]

or [►] key to select “←” or “→”, press the [SELECT]
soft key until the incorrect number is selected, then
perform step 2.
5. When entering the number is complete, press the
[FINISH] soft key. The Radio will ask you to input the
ATIS number again. Perform steps 2 through 4 above.
6. After the number has been entered twice, press the
[FINISH] soft key to store the ATIS number in memory.
7. Press the [OK] soft key to return to radio operation.
122
20.2 ATIS CH GROUP
The GX2400GPS/E has ATIS feature may be turned ON or OFF for each
channel group.
1. Press & hold [ ]  “ATIS SETUP”  “ATIS GROUP”
2. Rotate the DIAL/ENT knob to select the channel

group (International, Canadian*, or USA) to change
the setting, and then press the [SELECT] soft key.
*(Depending on the region setting.)
5. To set the ATIS feature for another channel group,
repeat steps 2 through 4.
6. Press the [BACK] soft key to return to radio operation.
NOTE
• The “Scan” and “Dual Watch” features are not available on the channel
group while the ATIS feature is turned on.
• The TX output power is set to “1 W” automatically on the following chan-
nels of the channel group while the ATIS feature is turned on.
CH 06, 08, 10, 11, 12, 13, 14, 15, 17, 71, 72, 74, 75, 76, and 77
123
21 SSM-70H (RAM4) REMOTE MIC OPERATION
NOTE
To connect the GX2400, the SSM-70H firmware must be Ver. 3.00.00 or later.
When a remote microphone is connected to the GX2400, all VHF, DSC, setup
menus, AIS, Navigation, GM (Group Monitor) functions and PA/Fog modes can
be remotely operated. The SSM-70H operation is the same as the GX2400 except
for the receiver audio volume setting and the squelch level setting. The reason
for combined controlling is to make the operation of the radio and SSM-70H
Remote Microphone uncomplicated. For specific operations of the SSM-70H
Remote Microphone, review sections in the transceiver operating manual. The
SSM-70H is supplied with 7 meters of routing cable and can be extended up to
21 meters using three 7-meter extension cables model CT-100. The Intercom
feature can be used between the SSM-70H and the GX2400. In addition, speaker
wires are supplied at the panel mount of the routing cable for external speakers
to be connected for use in noisy environments.
21.1 REMOTE MIC CONTROLS
 

 


 


Power/VOL knob
Press and hold this knob to turn the transceiver and the remote mic ON or OFF.
Rotate this knob to adjust the internal speaker volume.
124
DIAL/ENT knob
While the normal screen is displayed, rotate the DIAL/ENT knob to select
your desired channel. While the MENU screen is displayed, rotate the knob
to select the desired menu item.
Secondary use
Press this knob to enter a selection in the MENU.
SQL key (Squelch control)
Press this key to activate the squelch adjusting mode. Press the CH▲ or
CH▼ key to adjust the squelch threshold level.
PTT (Push-To-Talk) switch
Push this switch to enable the transmitter.
CLEAR/ key
Press this key to cancel a menu selection. Press and hold this key to activate the
key lock function. Press and hold this key again to deactivate the key lock function.
Microphone
The internal microphone transmits your voice while reducing background
noise using Clear Voice Noise Reduction Technology.
NOTE: Position the microphone about 1.5 cm away from your mouth and speak in a normal voice.
◄ & ► keys
When the soft keys are displayed, press these keys to switch the function
of the soft keys.
Secondary use
While the MENU screen is displayed, press the keys to slide the on-screen
menu to the right/left side.
MENU key
Press to access the MENU.
Press and hold this key to access the SETUP MENU.
CH▼ & CH▲ keys
These keys are used to change the operating channel.
Press the key momentarily, the channel increases or decreases one step.
Hold the key and the channel increases or decreases continuously.
Secondary use
 While the MENU screen is displayed, press the key to slide the on-screen
menu upward/downward.
 When in the PA or Fog mode, press the key to change the channel.
Display
Full dot matrix display, 222 by 162 pixels.
MMSI and ATIS Display Area (Fixed)
Channel and Operation status

Display area
125
Soft keys
These three programmable keys can be customized utilizing the setup menu.
Press one of these keys, to display the key functions at the bottom of the
display. Refer to section “21.2 RAM4 SOFT KEY ASSIGNMENT” for details.
Strobe Light
When the [STROBE] soft key is pressed, the internationally recognized
Morse Code “S.O.S” message will light and flash repeatedly.
From MENU → SETUP → CONFIGURATION → STROBE LED, the strobe light
may be set to one option from: “CONTINUOUS”, “SOS”, “BLINK 1”, “BLINK 2”
or “BLINK 3”.
16/S key
Pressing this key immediately reverts to channel 16 from any channel loca-
tion. Holding down this key recalls the SUB channel (The default setting is
channel 9). Press this key again to revert to the previously selected working
channel.
Speaker
The internal speaker is located here.
DATA jack
Use the micro USB type B jack for SSM-70H (RAM4) firmware updates.
NOTE: When the DATA jack is securely covered with the rubber cap, the SSM-70H
meets the waterproof performance.
DISTRESS key
This key is used to send a DSC distress call. Refer to section “11 DIGITAL
SELECTIVE CALLING (DSC)”.
21.2 RAM4 SOFT KEY ASSIGNMENT

From this menu, desired functions may be assigned to each RAM4 soft key
from numbers 01 to 12. Also, the duration the soft key icon will be displayed
after the corresponding soft key is pressed may be set. The keys may be setup
to control the following functions:
DISPLAY SOFT KEY ICON FUNCTION
NONE − −
TX HI/LO Selects transmit power
Switches channels between weather

WX/CH and marine
SCAN Turns the scanning function ON or OFF
Starts and stops dual watch or triple

MULTI WATCH watch scan
MARK POSITION Marks the current position for a “Waypoint”
126
DISPLAY SOFT KEY ICON FUNCTION
Add or remove channels from memory
SCAN MEMORY channel scan
Programs or deletes the preset memory
PRESET channel
Marks the position where a person falls
MAN OVERBOARD overboard
Enables the noise canceling settings
NOISE CANCEL display
CH NAME Edit channel names
STROBE Turns on or off the strobe LED.
Configures the secret communication

SCRAMBLER settings.
COMPASS Enables the “Compass” display
Enables the “Waypoint” or “Route”

NAVIGATION navigation display
FOG HORN Select FOG HORN mode
Activates intercom between radio and

INTERCOM RAM4 microphone (optional SSM-70H
(RAM4) or SSM-72H (RAM4X) required)
GPS LOGGER Starts and stops logging position data
AIS DISPLAY Shows the “AIS” display
HORN BUTTON Activates the Fog Horn function
Switches channels between weather

PUBLIC ADDRESS and marine
RX SENSE Toggles between LOCAL and DISTANCE
Switches the display between daytime

DISPLAY MODE and nighttime mode
NOTE
Soft key functions may be assigned individually for the transceiver and the
optional SSM-70H (RAM4) remote microphone.
21.2.1 Key Assignment

Customize the functions of SSM-70H (RAM4) remote microphone soft keys
for personal preferences.
NOTE: It is necessary to make the settings using the keys or the DIAL/ENT knob on
the SSM-70H (RAM4).
Press & hold [ ]  “CONFIGURATION”  “SOFT KEY”

1.
(RAM4)
127
2. Rotate the DIAL/ENT knob to select “KEY ASSIGN-
MENT”, then press the [SELECT] soft key.
3. Rotate the DIAL/ENT knob to select the key number

to be programmed, and press the [SELECT] soft key.
4. Rotate the DIAL/ENT knob to select a new function

from the choices listed, and then press the [ENTER]
soft key. When “NONE” is selected, the soft key
assignment is removed.
5. Repeat steps 3 and 4 to program other soft keys.
The VHF radio's functions can be assigned to the maximum of 12 soft keys.
6. Press the [CLEAR/ ] key to return to radio operation.
22 CONNECTING A USB DATA TERMINAL TO THE PC

The GX2400 settings can be programmed using the USB terminal and PC
Programming Software. You can also download the log data from the radio by
using the PC Programming Software which may be downloaded from the Standard
Horizon website. The PC Programming Software is compatible with Windows®.
To connect a PC, use the supplied USB cable through the DATA jack of the GX2400.
DATA
USB
USB Cable (Supplied with GX2400GPS)
CAUTION
The DATA jack is NOT designed to be waterproof when the cover is opened.
Connect the radio and PC in a dry location.
If you have further questions, please feel free to contact Product Support at:
Phone: (800) 767-2450
Email: marinetech@yaesu.com
128
23 MAINTENANCE
The inherent quality of the solid-state components used in this transceiver will
provide many years of continuous use. Taking the following precautions will
prevent damage to the transceiver.
• Never key the microphone unless an antenna or suitable dummy load is
connected to the transceiver.
• Ensure that the supply voltage to the transceiver does not exceed 16 VDC
or fall below 11 VDC.
• Use only STANDARD HORIZON approved accessories and replacement parts.
23.1 REPLACEMENT PARTS

Occasionally an owner needs a replacement mounting bracket or knob.
These can be ordered from your Dealer.
Commonly requested parts, and their part numbers are listed below.
• DC Power Cord: T9025406
• VOL Knob: RA6274300
• SQL Knob: RA6283700
• DIAL/ENT Knob: RA6271400
• Mounting Bracket: RA078400C
• Mounting Bracket Knob: RA0978600
• Microphone Hanger: RA0458800
• SSM-70H (RAM4 Microphone) Routing Cable Assembly: S8101512
• USB Cable: T9101648
23.2 FACTORY SERVICE

In the unlikely event that the transceiver fails to perform or needs servicing,
please contact one of following:
In USA and Canada
Standard Horizon
Attention Marine Repair Department
6125 Phyllis Drive, Cypress, California 90630, U.S.A.
Telephone (800) 366-4566
In Europe
Yaesu (UK) Ltd
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U. K.
Telephone +44 (0)1962 866667
In Other Countries
Contact the dealer or the distributor.
129
23.3 TROUBLESHOOTING CHART
SYMPTOM PROBABLE CAUSE REMEDY
Transceiver fails to No DC voltage to the a. Check the 12 VDC battery connections
power up. transceiver, or blown fuse. and the fuse.
b. The key needs to be pressed and held
to turn the radio on.
Transceiver Reversed power wires. Check the power cable for DC
blows fuse when voltage, or replace the fuse (6A).
connected to Make sure the red wire is connected to the
power supply. positive (+) battery post, and the black wire
is connected to the negative (–) battery post.
If the fuse still blows, contact your Dealer.
Popping or whin- Engine noise. Re-route the DC power cables away from
ing noise from the engine. Add noise suppressor on power
the speaker while cable. Change to resistive spark plug wires
engine runs. and/or add an alternator whine filter.
Sound is not emit- Accessory cable. Check the connections of the acces-
ted from the inter- sory cable. External speaker cable (WHITE/
nal or external SHIELD) may be shorted together.
speaker.
Receiving station Antenna. Have the antenna checked or test the trans-
reports low transceiver with another antenna. If the problem
mit power, even persists, contact your Dealer for servicing.
with transceiver
set to HI power.
“HI BATTERY” or The power supply voltage Confirm that the connected power supply
“ L O B AT T E RY ” is too high or too low. voltage is between 11 volts and 16.5 volts
message appears DC.
when the power is
turned on.
Your position is not Accessory cable. Check the accessory cable connection.
displayed. Some GPS use the battery ground for NMEA
connection.
SCU-38 cable. Check the SCU-38 cable connection.
Setting of the GPS chart Check the output signal format of the GPS
plotter. navigation receiver. This radio requires
NMEA 0183 and NMEA 2000 format with
GLL, RMB, or RMC sentence as an output
signal. If the GPS has a baud rate setting
make sure to select 4800 and parity to
NONE.
130
24 CHANNEL ASSIGNMENTS
24.1 GX2400GPS
VHF MARINE CHANNEL CHART
CH U C I S/D TX RX CHANNEL USE
01 X X D 156.050 160.650 Public Correspondence (Marine Operator)
Port Operation and Commercial.
1001 X S 156.050 VTS in selected areas
1003 X S 156.150 U.S. Government Only, Coast Guard
04 X D 156.200 160.800 Public Correspondence (Marine Operator),

Port operation, ship movement
Pacific coast: Coast Guard, East Coast:
1004 X S 156.200 Commercial fishing
Public Correspondence (Marine Operator),
05 X D 156.250 160.850 Port operation, ship movement
1005 X X S 156.250 Port operation. VTS in Seattle
06 X X X S 156.300 Inter-ship Safety
1007 X X S 156.350 Commercial
08 X X X S 156.400 Commercial (Inter-ship only)
Boater Calling channel, Commercial &
09 X X X S 156.450 Non-commercial (Recreational)
10 X X X S 156.500 Commercial
11 X X X S 156.550 Commercial. VTS in selected areas.
12 X X X S 156.600 Port operation. VTS in selected areas.
13 X X X S 156.650 Inter-ship Navigation Safety (Bridge-to-bridge)
14 X X X S 156.700 Port operation. VTS in selected areas.
15 X S --- 156.750 Environmental (Receive only)
Commercial, non-commercial, ship
15 X X S 156.750 movement (1 W)
16 X X X S 156.800 International Distress, Safety and Calling
17 X X X S 156.850 State Controlled (1 W)
Commercial (USA)
1019 X X S 156.950
Coast Guard (Canada)
1019 X S 156.950
2019 X S 161.550
Canadian Coast Guard Only,
20 X X X D 157.000 161.600 International: port operations and shipment
1020 X S 157.000
1020 X S 157.000 Port operation
2020 X S 161.600
U.S. Government Only (USA)
1021 X X S 157.050
Canadian Coast Guard (Canada)
2021 X --- 161.650 CMB Service
131
US Coast Guard Liaison and Maritime
Safety Information Broadcasts announced
on channel 16 (USA)
1022 X X S 157.100
Canadian Coast Guard Liaison and Maritime
Safety Information Broadcasts announced
on channel 16 (Canada)
1023 X S 157.150 U.S. Government Only
2023 X --- 161.750 CMB Service
24 X X X D 157.200 161.800 Public Correspondence (Marine Operator)
2025 X --- 161.850 CMB Service
2028 X --- 162.000 CMB Service
Public Coast: Coast Guard;
1061 X X S 156.075 East Coast: commercial fishing only
Public Coast: Coast Guard;
1062 X S 156.125 East Coast: commercial fishing only
Port Operation and Commercial.
1063 X X S 156.175 VTS in selected areas.
64 X X D 156.225 160.825 Public Correspondence (Marine Operator),
1064 X X S 156.225 Public Correspondence (Marine Operator),
1065 X X S 156.275 Port Operations
1066 X X S 156.325 Port Operations
US: Commercial. Used for Bridge-to-bridge
communications in lower Mississippi River.
67 X X X S 156.375 Inter-ship only.
Canada: Commercial fishing, S&R
68 X X X S 156.425 Non-commercial (Recreational)
US: Non-commercial (Recreational),
Canada: Commercial fishing only,
69 X X X S 156.475 International: Inter-ship, Port operations and
Ship movement
Digital selective calling (voice
70 X X X S --- 156.525 communications not allowed)
132
US, Canada: Non-commercial
71 X X X S 156.575 (Recreational),
International: Port operations and Ship movement
72 X X X S 156.625 Non-commercial (Inter-ship only)
US: Port Operations,
73 X X X S 156.675 International: Inter-ship, Port operations
and Ship movement
US: Port Operations,
74 X X X S 156.725 International: Inter-ship, Port operations
and Ship movement
75 X X X S 156.775 Port Operations (Inter-ship only) (1 W)
76 X X X S 156.825 Port Operations (Inter-ship only) (1 W)
77 X X S 156.875 Port Operations (Inter-ship only) (1 W)
77 X S 156.875 Port Operations (Inter-ship only)
78 X D 156.925 161.525 Port operation, ship-movement
1078 X X S 156.925 Non-commercial (Recreational)
1078 X S 156.925 Port operation and Ship movement
2078 X S 161.525
79 X D 156.975 161.575 Port operation and Ship movement
1079 X S 156.975 Port operation and Ship movement
2079 X S 161.575
U.S. Government Only - Environmental
1081 X X S 157.075 protection operations. (USA)
Canadian Coast Guard Only (Canada)
1082 X X S 157.125
83 X D 157.175 161.775 Public Correspondence (Marine Operator)
1083 X X S 157.175
2083 X --- 161.775 CMB Service
87 X X X S 157.375 Port operation, ship movement
88 X X X S 157.425 Commercial, Inter-ship Only
NOTE: Simplex channels, 1003, 1021, 1023, 1061, 1064, 1081, 1082 and 1083 CANNOT be
lawfully used by the general public in U.S.A. waters.
133
24.2 GX2400GPS/E
CHANNEL USE
CH TX (MHz) RX (MHz) SIMPLEX/DUPLEX LOW PWR All countries
Germany
(except Germany)
01 156.050 160.650 DUPLEX – TELEPHONE NAUTIK
04 156.200 160.800 DUPLEX – INTL NAUTIK
06 156.300 SIMPLEX LOW*4 SAFETY SHIP-SHIP
08 156.400 SIMPLEX LOW*4 COMMERCIAL SHIP-SHIP
09 156.450 SIMPLEX – CALLING NAUTIK
10 156.500 SIMPLEX LOW*4 COMMERCIAL SHIP-SHIP
11 156.550 SIMPLEX LOW*4 VTS SHIP-PORT
13 156.650 SIMPLEX LOW*4 BRG/BRG SHIP-SHIP
15 156.750 SIMPLEX LOW COMMERCIAL ON-BOARD
16 156.800 SIMPLEX – DISTRESS
17 156.850 SIMPLEX LOW SAR ON-BOARD
1019 156.950 SIMPLEX – – –
2019 161.550 SIMPLEX – – –
20 157.000 161.600 DUPLEX LOW*6 PORT OPR NAUTIK
1020 157.000 SIMPLEX – – –
2020 161.600 SIMPLEX – – –
23 157.150 161.750 DUPLEX – INTL
24 157.200 161.800 DUPLEX – TELEPHONE
31*1 157.550 162.150 DUPLEX LOW NED JACHTHAV –
37*2 157.850 SIMPLEX LOW YACHTING UK –
67 156.375 SIMPLEX – BRG/BRG NAUTIK
68 156.425 SIMPLEX – SHIP-SHIP
69 156.475 SIMPLEX – PLEASURE
70 – 156.525 SIMPLEX – DSC
71 156.575 SIMPLEX LOW*4 PLEASURE SHIP-PORT
72 156.625 SIMPLEX LOW*4 SHIP-SHIP
73 156.675 SIMPLEX – PORT OPR NAUTIK
74 156.725 SIMPLEX LOW*4 PORT OPR SHIP-PORT
75 156.775 SIMPLEX LOW – SHIP-PORT
76 156.825 SIMPLEX LOW – NAUTIK
134
CHANNEL USE
CH TX (MHz) RX (MHz) SIMPLEX/DUPLEX LOW PWR All countries
Germany
(except Germany)
77 156.875 SIMPLEX LOW*4 PORT OPR SHIP-SHIP
1078 156.925 SIMPLEX – – –
2078 161.525 SIMPLEX – – –
1079 156.975 SIMPLEX – – –
2079 161.575 SIMPLEX – – –
82 157.125 161.725 DUPLEX – INTL TELEPHONE
83 157.175 161.775 DUPLEX – INTL TELEPHONE
87 157.375 SIMPLEX – PORT OPR
88 157.425 SIMPLEX – PORT OPR
M*3 157.850 SIMPLEX – YACHTING UK –
M2*3 161.425 SIMPLEX – YACHTING UK –
L1*5 155.500 SIMPLEX – PLEASURE –
F1*5 155.625 SIMPLEX – FISHING –
NOTE: Country Channel assignment are different depending on the region.

*1: Channel 31 is assigned to only BELGIUM and NETHERLAND.
*2: Channel 37 is assigned to only NETHERLAND.
*3: Channel M and M2 are assigned to only UNITED KINGDOM.
*4: LOW Power setting for BELGIUM, NETHERLAND and GERMANY.
*5: Channel L1, L2, L3, F1, F2 and F3 are assigned to only SWEDEN.
*6: LOW Power setting for GERMANY.
135
25 SPECIFICATIONS
Performance specifications are nominal, unless otherwise indicated, and are
subject to change without notice. Measured in accordance with TIA/EIA-603.
zzGENERAL
Channels .............................................. All International, USA and Canadian*
*(Depending on the region setting)
Normal Input Voltage ...................................................................... 13.8 V DC
Operating Voltage Range ......................................................... 11 V to 16.5 V
Current Drain
Standby............................................................................................. 0.55 A
Receiver (at Maximum AF Output) ..................................................... 0.9 A
Transmit ...................................................................... 5.0 A (Hi), 1.0 A (Lo)
NMEA 2000 Load Equivalency Number ............................................... LEN=1
DSC Transmitted Call Log ......................................................................... 100
DSC Distress Call Log ................................................................................. 50
DSC Received Call Log ............................................................................. 100
Individual Directory .................................................................................... 100
Group Directory ........................................................................................... 30
Waypoint Directory .................................................................................... 250
Route Directory ........................................................................................... 30
Display Type .............................................................. 2.6” x 1.4” (66 x 36 mm)
Full Dot Matrix (222 x 122 pixels)
Dimensions (W x H x D) .......................... 7.1" x 3.1" x 6.0" (180 x 80 x 152.6 mm)
Flush-Mount Dimensions (W x H x D) ....... 6.3" x 2.6" x 6.2" (161 x 65 x 157 mm)
Weight ..................................................................................... 3.3 lbs (1.5 kg)
z
zTRANSMITTER
Frequency Range ............ 156.025 MHz to 161.600 MHz (INTERNATIONAL)
RF Output Power .............................................................. 25 W (Hi), 1 W (Lo)
Conducted Spurious Emissions ........... Less than −80 dBc (Hi), −66 dBc (Lo)
Audio Response .......................................... within +1/−3dB of a 6 dB/Octave
pre-emphasis characteristic at 300 to 3000 Hz
Audio Distortion ........................................................................ Less than 5 %
Modulation .................................... 16K0G3E (for Voice), 16K0G2B (for DSC)
Frequency Stability ............. ±0.0003 % (–4 °F to +140 °F [−20 °C to +60 °C])
FM Hum and Noise ................................................................................ 50 dB
136
z
zRECEIVER (for Voice and DSC)
Frequency Range ............................................ 156.050 MHz to 163.275 MHz
Sensitivity
20 dB Quieting ............................................................................... 0.35 µV
12 dB SINAD ................................................................................. 0.30 µV
Squelch Sensitivity (Threshold) ..................................................... 0.13 µV
Modulation Acceptance Bandwidth ................................................... ±7.5 kHz
Selectivity (Typical)
Spurious and Image Rejection ................ 80 dB for Voice (75 dB for DSC)
Intermodulation and Rejection ................. 75 dB for Voice (75 dB for DSC)
Audio Output ................................ 4.5 W (at 4 ohms external speaker output)
Audio Response .......................................... within +1/–3dB of a 6 dB/Octave
de-emphasis characteristic at 300 to 3000 Hz
Frequency Stability ............. ±0.0003 % (–4 °F to +140 °F [−20 °C to +60 °C])
Channel Spacing .................................................................................. 25 kHz
DSC Format .. ......................................................................... ITU-R M.493-15
Attenuator (Local)....................................................................... Approx. 10 dB
z
zRECEIVER (for AIS)
Frequency .................................. 161.975 MHz (CH A), 162.025 MHz (CH B)
Sensitivity ................................................................. 0.5 µV (at 12 dB SINAD)
Selectivity(Typical)
Spurious and Image Rejection .......................................................... 70 dB
Intermodulation and Rejection ........................................................... 70 dB
z
zINTERNAL GPS RECEIVER
Receiver Channels ...................................................................... 66 Channels
Sensitivity ........................................................................ Less than –147 dBm
Time to First Fix ............................................... 1 minute typical (@Cold Start)
5 seconds typical (@ Hot Start)
Geodetic Datum ................................................................................. WGS84
NMEA 0183 INPUT/OUTPUT Sentences
4800 Baud selected:
NMEA 0183 Input (4800 baud) ............. GGA, GLL, GNS, RMC, GSA, & GSV
NMEA 0183 Output (4800 baud) ...................... DSC, DSE, GGA, GLL, GNS,
RMC, GSA & GSV
NMEA 0183-HS AIS Output (38400 baud)............................................VDM
38400 Baud selected:
NMEA 0183-HS Input (38400 baud) .... GGA, GLL, GNS, RMC, GSA, & GSV
NMEA 0183-HS Output (38400 baud) .............. DSC, DSE, GGA, GLL, GNS,
RMC, GSA & GSV
NMEA 0183-HS AIS Output (38400 baud) .......................................... VDM
137
25.1 DIMENSIONS
6.3” (159mm)
6.2” (156mm)
7.1” (180mm) 1.7” (44mm) 4.8” (121.8mm)
1.2” (30.8mm) 3.8” (97.4mm)

7.1” (180mm)
3.1” (80mm)
3.1” (80mm)
2.5” (63mm)
1.5” (36.9mm)
7.8” (197.4mm)
6.3” (159mm)
6.2” (156mm)
7.1” (180mm) 1.7” (44mm) 4.8” (121.8mm)
7.1” (180mm) 1.2” (30.8mm) 3.8” (97.4mm)

3.1” (80mm)
2.5” (63mm)
4.7” (118.5mm)
1.5” (36.9mm)
6.8” (172mm)
138
26 FCC RADIO LICENSE INFORMATION
Standard Horizon radios comply with the Federal Communication Commission
(FCC) requirements that regulate the Maritime Radio Service.
26.1 STATION LICENSE

An FCC ship station license is no longer required for any vessel traveling in
U.S. waters (except Hawaii) which is under 20 meters in length. However, any
vessel required to carry a marine radio on an international voyage, carrying
a HF single side band radiotelephone or marine satellite terminal is required
to have a ship station license. FCC license forms, including applications for
ship (605) and land station licenses can be downloaded via the Internet at
https://www.fcc.gov/fcc-form-605. To obtain a form from the FCC, call (888)
225-5322.
26.2 RADIO CALL SIGN

Currently the FCC does not require recreational boaters to have a Ship Radio
Station License. The USCG recommends the boats registration number and
the state to be used when calling another vessel.
26.3 CANADIAN SHIP STATION LICENSING

Please click on the following link for licensing information:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/h_sf01775.html
The following link lists several Branches/Offices regarding licensing. Licensing
depends on the region of operations.
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01742.html
26.4 FCC / IC INFORMATION

The following data pertaining to the transceiver is necessary to fill out the
license application.
FCC Type Accepted ..................................................................... FCC Part 80
IC Type Accepted ............................................................................. RSS-182
Output Power ............................................... 1 Watt (low) and 25 Watts (high)
Emission ......................................................................... 16K0G3E, 16K0G2B
Frequency Range ..................................................... 156.025 to 163.275 MHz
FCC ID ...................................................................................... K6630673X3D
IC ........................................................................................... 511B-30673X3D
139
27 FCC NOTICE
NOTICE
Unauthorized changes or modifications to this equipment may void compli-

ance with FCC Rules. Any change or modification must be approved in writing
by STANDARD HORIZON.
NOTICE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
WARNING
It is a violation of the rules of the Federal Communications Commission to

input an MMSI that has not been properly assigned to the end user, or to
otherwise input any inaccurate data in this device.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Changes or modifications to this device not expressly approved by YAESU U.S.A.

could void the User’s authorization to operate this device.
140
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Cana-
da applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
(1) L’ appareil ne doit pas produire de brouillage;
(2) L’ appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-
lage est susceptible d’ en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using
an antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio
peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le
type d’antenne et son gain de sorte que la puissance isotrope rayonnée quivalente
(p.i.r.e.) ne dépassepas l’intensité nécessaire à l’établissement d’une communication
satisfaisante.
CAN ICES-3 (B) / NMB-3 (B)
FCC APPLICATION
The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 1.41 meters from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter.
ISED APPLICATION
The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 1.76 meters from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter.
141
STANDARD HORIZON Limited Warranty
Limited Warranty is valid only in the country/region where this product was originally purchased.
On-line Warranty Registration:
Thank you for buying STANDARD HORIZON products! We are confident your new radio will serve your needs
for many years! Please register your product at www.standardhorizon.com - Owner’s Corner
Warranty Terms:
Subject to the Limitations of the Warranty and the Warranty Procedures described below, YAESU MUSEN
hereby warrants this product to be free of defects in materials and workmanship in normal use during the “War-
ranty Period.” (the “Limited Warranty”).
Limitations of Warranty:
A. YAESU MUSEN is not liable for any express warranties except the Limited Warranty described above.
B. The Limited Warranty is extended only to the original end-use purchaser or the person receiving this product
as a gift, and shall not be extended to any other person or transferee.
C. Unless a different warranty period is stated with this YAESU product, the Warranty Period is three years from
the date of retail purchase by the original end-use purchaser.
D. The Limited Warranty is valid only in the country/region where this product was originally purchased.
E. During the Warranty Period, YAESU MUSEN will, at its sole option, repair or replace (using new or refur-
bished replacement parts) any defective parts within a reasonable period of time and free of charge.
F. The Limited Warranty does not cover shipping cost (including transportation and insurance) from you to us,
or any import fees, duties or taxes.
G. The Limited Warranty does not cover any impairment caused by tampering, misuse, failure to follow instruc-
tions supplied with the product, unauthorized modifications, or damage to this product for any reasons, such
as: accident; excess moisture; lightning; power surges; connection to improper voltage supply; damage
caused by inadequate packing or shipping procedures; loss of, damage to or corruption of stored data; prod-
uct modification to enable operation in another country/purpose other than the country/purpose for which
it was designed, manufactured, approved and/or authorized; or the repair of products damaged by these
modifications.
H. The Limited Warranty applies only to the product as it existed at the time of the original purchase, by the
original retail purchaser, and shall not preclude YAESU MUSEN from later making any changes in design,
adding to, or otherwise improving subsequent versions of this product, or impose upon YAESU MUSEN any
obligation to modify or alter this product to conform to such changes, or improvements.
I. YAESU MUSEN assumes no responsibility for any consequential damages caused by, or arising out of, any
such defect in materials or workmanship.
J. TO THE FULLEST EXTENT PERMITTED BY LAW, YAESU MUSEN SHALL NOT BE RESPONSIBLE FOR
ANY IMPLIED WARRANTY WITH RESPECT TO THIS PRODUCT.
K. If the original retail purchaser timely complies with the Warranty Procedures described below, and YAESU
MUSEN elects to send the purchaser a replacement product rather than repair the “original product”, then
the Limited Warranty shall apply to the replacement product only for the remainder of the original product
Warranty Period.
L. Warranty statutes vary from state to state, or country to country, so some of the above limitations may not
apply to your location.
Warranty Procedures:
1. To find the Authorized STANDARD HORIZON Service Center in your country/region, visit www.standardho-
rizon.com. Contact the STANDARD HORIZON Service Center for specific return and shipping instructions,
or contact an authorized STANDARD HORIZON dealer/distributor from whom the product was originally
purchased.
2. Include proof of original purchase from an authorized STANDARD HORIZON dealer/distributor, and ship
the product, freight prepaid, to the address provided by the STANDARD HORIZON Service Center in your
country/ region.
3. Upon receipt of this product, returned in accordance with the procedures described above, by the STAN-
DARD HORIZON Authorized Service Center, all reasonable efforts will be expended by YAESU MUSEN to
cause this product to conform to its original specifications. YAESU MUSEN will return the repaired product
(or a replacement product) free of charge to the original purchaser. The decision to repair or replace this
product is the sole discretion of YAESU MUSEN.
Other conditions:
YAESU MUSEN’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR
THE PRODUCT. IN NO EVENT SHALL YAESU MUSEN BE LIABLE FOR LOSS OF, DAMAGE TO OR COR-
RUPTION OF STORED DATA, OR FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR INDIRECT DAM-
AGES, HOW EVER CAUSED; INCLUDING WITHOUT LIMITATION TO THE REPLACEMENT OF EQUIP-
MENT AND PROPERTY, AND ANY COSTS OF RECOVERING, PROGRAMMING OR REPRODUCING ANY
PROGRAM OR DATA STORED IN OR USED WITH THE YAESU PRODUCT.
Some Countries in Europe and some States of the USA do not allow the exclusion or limitation of incidental or
consequential damages, or a limitation on how long an implied warranty lasts, so the above limitation or exclu-
sions may not apply. This warranty provides specific rights, there may be other rights available which may vary
between countries in Europe or from state to state within the USA.
This Limited Warranty is void if the label bearing the serial number has been removed or defaced.
142
cut here
TEMPLATE for the GX2400 series
R
10
65 mm
161 mm
Use this template to mark the location where the

rectangular hole for the flush mount is to be cut.
Declaration of Conformity
Type of Equipment: 25 Watt VHF/FM Marine Transceiver
Brand Name: STANDARD HORIZON
Model Number: GX2400GPS
Manufacturer: YAESU MUSEN CO., LTD.
Address of Manufacturer: Tennozu Parkside Building, 2-5-8 Higashi-Shinagawa,
Shinagawa-ku,Tokyo 140-0002 Japan
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions; (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The technical documentation as required by the Conformity Assessment procedures is
kept at the following address:
Company: Yaesu U.S.A.
Address: 6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
Telephone: (714) 827-7600
EU Declaration of Conformity
We, Yaesu Musen Co. Ltd of Tokyo, Japan, hereby declare that this radio equipment
GX2400GPS/E is in full compliance with EU Radio Equipment Directive 2014/53/EU. The
full text of the Declaration of Conformity for this product is available to view at http://www.
yaesu.com/jp/red/
Disposal of Electronic and Electrical Equipment

Products with the symbol (crossed-out wheeled bin) cannot be disposed as
household waste.
Electronic and Electrical Equipment should be recycled at a facility capable of
handling these items and their waste by-products.
Please contact a local equipment supplier representative or service center for
information about the waste collection system in your country.
ATTENTION – Conditions of usage

This transceiver works on frequencies that are regulated
and not permitted to be used without authorisation in the
EU countries shown in this table. Users of this equipment
AT BE BG CY CZ DE
should check with their local spectrum management DK ES EE FI FR UK
authority for licensing conditions applicable for this EL HR HU IE IT LT
LU LV MT NL PL PT
equipment. RO SK SI SE CH IS
LI NO – – – –
Copyright 2021
YAESU MUSEN CO., LTD.
All rights reserved.
No portion of this manual may be
reproduced without the permission of

Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan
YAESU USA 2005M-BC-1
6125 Phyllis Drive, Cypress, CA 90630, U.S.A. Printed in China
YAESU UK
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
*EM067N201*
E M 0 6 7 N 2 0 1

GX2400 e Om Eng Em067n201 2005M-BC-1

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

GX2400 e Om Eng Em067n201 2005M-BC-1

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GX2400 e Om Eng Em067n201 2005M-BC-1

Uploaded by

Copyright:

Available Formats

Owner’s Manual

MATRIX NMEA2000 GPS

zz International ITU-R M.493-15 Class D DSC (Digital Selective Calling)

 Press and hold the key to turn the radio ON or OFF.

4 ONLINE WARRANTY REGISTRATION

Types and meanings of symbols

6.2 SELECTING AN ANTENNA

6.3 COAXIAL CABLE

6.4 DISTRESS AND HAILING (CHANNEL 16)

For additional information on AIS visit the USCG website:

6.7 Accuracy of COG

7.1 FRONT PANEL

PTT (Push-To-Talk) switch

7.3 REAR PANEL

VHF ANT Jack (VHF antenna jack)

8.3 MOUNTING THE RADIO

8.3.2 Optional MMB-84 Flush Mount Bracket

Reverse polarity battery connections will damage the radio!

Wire Color/Description Connection Examples

Wire Color/Description Connection Examples

Wire Color/Description Connection Examples

8.5.6 Connecting optional SCU-38 External GPS Antenna

8.5.7 Connecting optional SCU-31 External GPS Antenna

Green: NMEA IN(−) Black

The transceiver is capable of using an SSM-70H (RAM4) Remote Station Micro-

As close as possible As close as possible

Connecting an External Speaker to the RAM4 Mic Cable

1. On the RAM4 microphone, press and hold the [MENU/

4. Rotate the DIAL/ENT knob to select “INTERNAL” or

5. Press the [CLEAR] key to return to radio operation.

To connect the SSM-72H (RAM4X), the SCU-30 firmware must be Ver.

The GX2400 is capable of using a SSM-72H (RAM4X) Wireless Remote Station

8.6 INITIAL SETUP REQUIRED WHEN TURNING ON THE

Programming the MMSI

4. Press the [◄] or [►] key to select the first number of

1. Press the [MENU/SET] key to display “MENU”.

3. Rotate the DIAL/ENT knob to select “TIME OFFSET”,

4. Rotate the DIAL/ENT knob to select time offset of

3. Rotate the DIAL/ENT knob to select “TIME AREA”,

4. Rotate the DIAL/ENT knob to select “UTC” or

3. Rotate the DIAL/ENT knob to select “TIME FORMAT”,

4. Rotate the DIAL/ENT knob to select “24hour” or

8.8.4 Setting COG to True or Magnetic

3. Rotate the DIAL/ENT knob to select “MAGNETIC

4. Rotate the DIAL/ENT knob to select “OFF” or “ON”.

5. Press the [ENTER] soft key to store the selected

9.4 BASIC OPERATION OF THE SETUP MENU

4. Rotate the DIAL/ENT knob to select the desired

Press & hold [ ]  “DSC SETUP”  “INDIVIDUAL DIRECTORY”

9.6 SIMPLEX/DUPLEX CHANNEL USE

All channels are factory-programmed in accordance with FCC (USA), ISED

9.7 CHANNEL GROUP

1. Press & hold [ ]  “CHANNEL SETUP”  “CHANNEL GROUP”

2. Rotate the DIAL/ENT knob to select the desired chan-

9.9 MULTI WATCH (TO PRIORITY CHANNEL)

9.9.1 Setup the Multi Watch Operation

1. Press & hold [ ]  “CHANNEL SETUP”  “MULTI WATCH”