GR00000300 17

17-1
GROUP 17
ENGINE AND
EMISSION
CONTROL
CONTENTS
ENGINE CONTROL . . . . . . . . . . 17-3 DIAGNOSTIC TROUBLESHOOTING

STRATEGY . . . . . . . . . . . . . . . . . . . . . . 17-11
DIAGNOSTIC FUNCTION . . . . . . . . . . . 17-11
GENERAL DESCRIPTION . . . . . . 17-3 DIAGNOSTIC TROUBLE CODE CHART 17-15
DIAGNOSTIC TROUBLE CODE
ENGINE CONTROL SYSTEM PROCEDURES . . . . . . . . . . . . . . . . . . . 17-15
DIAGNOSIS . . . . . . . . . . . . . . . . . . 17-3 SYMPTOM CHART . . . . . . . . . . . . . . . . 17-53
SYMPTOM PROCEDURES . . . . . . . . . . 17-54
INTRODUCTION . . . . . . . . . . . . . . . . . . 17-3
DATA LIST REFERENCE TABLE . . . . . 17-79
TROUBLESHOOTING STRATEGY . . . 17-3
ECM <M/T> OR PCM <A/T> TERMINAL
SYMPTOM CHART . . . . . . . . . . . . . . . . 17-4
VOLTAGE REFERENCE CHART FOR
SYMPTOM PROCEDURES . . . . . . . . . 17-4
AUTO-CRUISE CONTROL SYSTEM
OPERATION . . . . . . . . . . . . . . . . . . . . . 17-81
SPECIAL TOOL . . . . . . . . . . . . . . . 17-8
SPECIAL TOOLS . . . . . . . . . . . . . . 17-83
ACCELERATOR PEDAL. . . . . . . . 17-9
REMOVAL AND INSTALLATION . . . . . 17-9
ON-VEHICLE SERVICE . . . . . . . . . 17-85
AUTO-CRUISE CONTROL SWITCH
AUTO-CRUISE CONTROL . . . . 17-9 CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . 17-85
COMPONENT CHECK. . . . . . . . . . . . . . 17-87
GENERAL DESCRIPTION . . . . . . 17-9
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . 17-10 AUTO-CRUISE CONTROL. . . . . . . 17-89
INTRODUCTION TO AUTO-CRUISE REMOVAL AND INSTALLATION. . . . . . 17-89
CONTROL SYSTEM DIAGNOSIS. . . . . 17-10
Continued on next page
17-2
EMISSION CONTROL . . . . . . . . 17-90 FUEL TANK DIFFERENTIAL PRESSURE

SENSOR CHECK. . . . . . . . . . . . . . . . . . 17-103
EVAPORATIVE EMISSION VENTILATION
GENERAL DESCRIPTION . . . . . . 17-90 SOLENOID CHECK . . . . . . . . . . . . . . . . 17-103
DIAGNOSIS . . . . . . . . . . . . . . . . . . 17-90 EXHAUST GAS RECIRCULATION (EGR)

SYSTEM . . . . . . . . . . . . . . . . . . . . . 17-104
SPECIAL TOOLS. . . . . . . . . . . . . . 17-91 GENERAL DESCRIPTION (EXHAUST
GAS RECIRCULATION SYSTEM). . . . . 17-104
COMPONENT LOCATION. . . . . . . . . . . 17-105
VACUUM HOSES . . . . . . . . . . . . . 17-92
EGR VALVE (STEPPER MOTOR)
VACUUM HOSE ROUTING. . . . . . . . . . 17-92
CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . 17-105
VACUUM CIRCUIT DIAGRAM . . . . . . . 17-94
EGR VALVE (STEPPER MOTOR)
VACUUM HOSE INSTALLATION . . . . . 17-95
CLEANING . . . . . . . . . . . . . . . . . . . . . . . 17-107
VACUUM HOSE CHECK. . . . . . . . . . . . 17-95
MASS AIRFLOW SENSOR CHECK . . . 17-107
ENGINE COOLANT TEMPERATURE
POSITIVE CRANKCASE VENTILATION SENSOR CHECK. . . . . . . . . . . . . . . . . . 17-107
SYSTEM. . . . . . . . . . . . . . . . . . . . . 17-96 CRANKSHAFT POSITION SENSOR
GENERAL DESCRIPTION (POSITIVE CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . 17-107
CRANKCASE VENTILATION SYSTEM) 17-96 REMOVAL AND INSTALLATION
COMPONENT LOCATION . . . . . . . . . . 17-97 <2.4L ENGINE> . . . . . . . . . . . . . . . . . . . 17-108
POSITIVE CRANKCASE VENTILATION REMOVAL AND INSTALLATION
SYSTEM CHECK. . . . . . . . . . . . . . . . . . 17-97 <3.8L ENGINE> . . . . . . . . . . . . . . . . . . . 17-109
POSITIVE CRANKCASE VENTILATION
VALVE CHECK . . . . . . . . . . . . . . . . . . . 17-98 EVAPORATIVE EMISSION CANISTER
AND FUEL TANK PRESSURE RELIEF
EVAPORATIVE EMISSION CONTROL VALVE . . . . . . . . . . . . . . . . . . . . . . 17-110
SYSTEM. . . . . . . . . . . . . . . . . . . . . 17-98 REMOVAL AND INSTALLATION. . . . . . 17-110
GENERAL DESCRIPTION (EVAPORATIVE INSPECTION . . . . . . . . . . . . . . . . . . . . . 17-111
EMISSION SYSTEM) . . . . . . . . . . . . . . 17-98
COMPONENT LOCATION . . . . . . . . . . 17-100
CATALYTIC CONVERTER . . . . . . 17-111
PURGE CONTROL SYSTEM CHECK
GENERAL DESCRIPTION
(PURGE FLOW CHECK). . . . . . . . . . . . 17-101
(CATALYTIC CONVERTER) . . . . . . . . . 17-111
EVAPORATIVE EMISSION PURGE
SOLENOID CHECK. . . . . . . . . . . . . . . . 17-102
MASS AIRFLOW SENSOR CHECK . . . 17-102 SPECIFICATIONS . . . . . . . . . . 17-112
BAROMETRIC PRESSURE SENSOR
CHECK . . . . . . . . . . . . . . . . . . . . . . . . . 17-102
ENGINE COOLANT TEMPERATURE FASTENER TIGHTENING
SENSOR CHECK . . . . . . . . . . . . . . . . . 17-103 SPECIFICATIONS . . . . . . . . . . . . . 17-112
INTAKE AIR TEMPERATURE SENSOR
CHECK . . . . . . . . . . . . . . . . . . . . . . . . . 17-103 SERVICE SPECIFICATIONS . . . . . 17-112
ENGINE AND EMISSION CONTROL
ENGINE CONTROL
17-3
ENGINE CONTROL
GENERAL DESCRIPTION
M1171000100471
For the accelerator system, an electronic throttle
actuator control system is utilized, eliminating the
accelerator cable.
CONSTRUCTION DIAGRAM
ACCELERATOR PEDAL
ASSEMBLY
[BUILT-IN ACCELERATOR PEDAL
POSITION SENSOR]
<VEHICLES WITH
ALUMINUM PEDAL PAD>
AC406079
AC305917
STOPPER AC406210 AB
ENGINE CONTROL SYSTEM DIAGNOSIS

INTRODUCTION
M1171002000306
If there is a malfunction in the engine control system,
the accelerator pedal or throttle body may be faulty.
TROUBLESHOOTING STRATEGY
M1171002100336
Use these steps to plan your diagnostic strategy. 2. Verify that the condition described by the
If you follow them carefully, you will be sure that you customer exists.
have exhausted most of the possible ways to find an 3. Find the malfunction by following the Symptom
engine control system fault. Chart.
1. Gather information from the customer. 4. Verify that the malfunction is eliminated.
TSB Revision
17-4 ENGINE AND EMISSION CONTROL
ENGINE CONTROL
SYMPTOM CHART
M1171002200355
SYMPTOM INSPECTION PROCEDURE REFERENCE PAGE

Throttle valve will not fully open or close 1 P.17-4
Accelerator pedal operation not smooth (over 2 P.17-6
acceleration)
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Throttle Valve will not Fully Open or Close
TROUBLESHOOTING HINTS (THE MOST

.
COMMENT
The throttle body or accelerator pedal position sen- LIKELY CAUSES FOR THIS CASE:)
sor is suspected. • Malfunction of the throttle body.
• Malfunction of the accelerator pedal position sen-
sor.
.
• Malfunction of the ECM <M/T> or PCM <A/T>.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
TSB Revision
ENGINE CONTROL
17-5
STEP 1. Using scan tool MB991958, read the diagnostic

trouble code (DTC).
CAUTION
AC305412 To prevent damage to scan tool MB991958, always turn the
DATA LINK
CONNECTOR ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Ensure that the ignition switch is at the "LOCK" (OFF)
position.
(2) Start up the personal computer.
(3) Connect special tool MB991827 to special tool MB991824
and the personal computer.
(4) Connect special tool MB991910 to special tool MB991824.
MB991910
(5) Connect special tool MB991910 to the data link connector.
MB991824 (6) Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator light will be illuminated in a green
color.
(7) Start the MUT-III system on the personal computer.
(8) Turn the ignition switch to the "ON" position.
(9) Check for MFI system diagnostic trouble code. (Refer to
GROUP 13A, MFI Diagnosis − Diagnostic Function − How
MB991827
AC404789AB to Read and Erase Diagnostic Trouble Code P.13A-6)
<2.4L engine> or (Refer to GROUP 13B, MFI Diagnosis −
Diagnostic Function − How to Read and Erase Diagnostic
Trouble Code P.13B-6) <3.8L engine>.
(10)Turn the ignition switch to the "LOCK" (OFF) position, and
then remove scan tool MB991958 in the reverse order of
installation.
Q: Is any DTC set?
YES : Repair MFI system. (Refer to GROUP 13A, MFI
Diagnosis − Diagnostic Trouble Code Chart
P.13A-41) <2.4L engine> or (Refer to GROUP 13B,
MFI Diagnosis − Diagnostic Trouble Code Chart
P.13B-43) <3.8L engine>. Then go to Step 2.
NO : Go to Step 2.
STEP 2. Retest the system.

Q: Does the throttle valve fully open and close?
YES : The procedure is complete.
NO : Return to Step 1.
TSB Revision
ENGINE CONTROL
INSPECTION PROCEDURE 2: Accelerator Pedal Operation not Smooth (Over Acceleration)

.
COMMENT
The accelerator pedal, its installation condition or the LIKELY CAUSES FOR THIS CASE:)
accelerator pedal position sensor is suspected. • Malfunction of the accelerator pedal.
• Incorrectly installed accelerator pedal.
• Malfunction of the accelerator pedal position sen-
.
sor.
DIAGNOSIS
• MB991824: V.C.I.
STEP 1. Check if the accelerator pedal is installed

correctly.
Q: Is the accelerator pedal installed correctly?
YES : Go to Step 2.
NO : Remove and reinstall the accelerator pedal. (Refer to
P.17-9). Go to Step 3.
TSB Revision
ENGINE CONTROL
17-7
STEP 2. Using scan tool MB991958, read the diagnostic

trouble code (DTC).
CAUTION
DATA LINK
(1) Ensure that the ignition switch is at the "LOCK" (OFF)
position.
(2) Start up the personal computer.
(3) Connect special tool MB991827 to special tool MB991824
(4) Connect special tool MB991910 to special tool MB991824.
MB991910
(5) Connect special tool MB991910 to the data link connector.
MB991824 (6) Turn the power switch of special tool MB991824 to the "ON"
position.
tool MB991824 indicator light will be illuminated in a green
color.
(7) Start the MUT-III system on the personal computer.
GROUP 13A, MFI Diagnosis −Diagnostic Function −How to
MB991827
AC404789AB Read and Erase Diagnostic Trouble Code P.13A-6) <2.4L
engine> or (Refer to GROUP 13B, MFI Diagnosis −
Diagnostic Function −How to Read and Erase Diagnostic
(10)Turn the ignition switch to the "LOCK" (OFF) position, and
then remove scan tool MB991958 in the reverse order of
installation.
Q: Is any DTC set?
YES : Repair MFI system. (Refer to GROUP 13A, MFI
Diagnosis −Diagnostic Trouble Code Chart P.13A-41)
<2.4L engine> or (Refer to GROUP 13B, MFI
Diagnosis −Diagnostic Trouble Code Chart P.13B-43)
<3.8L engine>. Then go to Step 3.
NO : Go to Step 3.

Q: Does the accelerator pedal work normally?
TSB Revision
ENGINE CONTROL
SPECIAL TOOL
M1171000600089
TOOL TOOL NUMBER AND SUPERSESSION APPLICATION

NAME
MB991958 MB991824-KIT Checking diagnostic trouble
A
A: MB991824 NOTE: G: codes
B: MB991827 MB991826 MUT-III CAUTION
C: MB991910 trigger harness is For vehicles with CAN
D: MB991911 not necessary communication, use MUT-III
MB991824
E: MB991914 when pushing main harness A to send
B F: MB991825 V.C.I. ENTER key. simulated vehicle speed. If
G: MB991826 you connect MUT-III main
MUT-III sub assembly harness B instead, the CAN
A: Vehicle communication does not
communication function correctly.
MB991827
interface (V.C.I.)
C
B: MUT-III USB cable
C: MUT-III main harness
A (Vehicles with CAN
communication
MB991910 system)
D D: MUT-III main harness
B (Vehicles without
DO NOT USE CAN communication
system)
E: MUT-III main harness
MB991911
C (for Daimler Chrysler
E models only)
F: MUT-III measurement
DO NOT USE adapter
G: MUT-III trigger
MB991914 harness
F
MB991825
MB991826
MB991958
TSB Revision
AUTO-CRUISE CONTROL
17-9
ACCELERATOR PEDAL
REMOVAL AND INSTALLATION
M1171003000172
2
13 ± 2 N·m
111 ± 22 in-lb
N 3
AC307006AC
REMOVAL STEPS REMOVAL STEPS (Continued)

1. ACCELERATOR PEDAL POSITION 2. ACCELERATOR PEDAL ASSEMBLY
SENSOR CONNECTOR 3. ACCELERATOR STOPPER
AUTO-CRUISE CONTROL
GENERAL DESCRIPTION
M1172000100429
By using the auto-cruise control system, the driver
can select and maintain a desired cruising speed
[between 40 km/h (25 mph) and 200 km/h (124
mph)] without depressing the accelerator pedal.
TSB Revision
AUTO-CRUISE CONTROL
CONSTRUCTION DIAGRAM
"CRUISE" INDICATOR
LIGHT
ACCELERATOR PEDAL ASSEMBLY

(BUILT-IN ACCELERATOR
PEDAL POSITION SENSOR)
STOPLIGHT SWITCH
THROTTLE BODY
AC406684
(BUILT-IN THROTTLE
POSITION SENSOR
AND THROTTLE
ACTUATOR CONTROL
MOTOR)
AUTO-CRUISE
CONTROL SWITCH
AC406686
8 16
CLUTCH PEDAL 7 15
TRANSMISSION ECM <M/T> OR 6 14
RANGE SWITCH PCM <A/T> POSITION SWITCH
5 13
<A/T> <M/T> 4 12
3 11
AC406683 2 10
1 9
DATA LINK
CONNECTOR AC406685
AC406687AB
AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

INTRODUCTION TO AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS
M1172003300303
The auto-cruise control system allows driving without <A/T> controls the throttle valve opening angle in the
stepping on the accelerator pedal by setting a ran- throttle body in accordance with the input signals
dom speed between 40 km/h (25 mph) and 200 km/h from the switches and sensors. If the PCM detects a
(124 mph). Malfunctions in this system can be inves- malfunction on any of those components, the ECM
tigated by the following methods. <M/T> or PCM <A/T> estimates where the problem
may be occurring, and will set a diagnostic trouble
Auto-cruise control system diagnostic code. Diagnostic trouble codes cover the auto-cruise
trouble codes control switch, stoplight switch and ECM <M/T> or
The auto-cruise control system consists of the PCM <A/T>.
engine control module (ECM) <M/T> or powertrain
control module (PCM) <A/T>, control switches and
sensors. The control switches and sensors monitor
the state of the vehicle. The ECM <M/T> or PCM
TSB Revision
AUTO-CRUISE CONTROL
17-11
DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1172002000547
Use these steps to plan your diagnostic strategy. If 5. If you can verify the condition but there are no
you follow them carefully, you will check most of the auto-cruise control system DTCs, find the fault.
possible causes of an auto-cruise control system (Refer to P.17-53, Symptom Chart).
malfunction. 6. If there is an auto-cruise control system DTC,
1. Gather information from the customer. record the number of the code, then erase the
2. Verify that the condition described by the code. (Refer to P.17-11, Diagnostic Function −
customer exists. How to Erase Diagnostic Trouble Codes).
3. Check the vehicle for any auto-cruise control 7. Re-create the auto-cruise control system DTC set
system DTC. (Refer to P.17-11, Diagnostic conditions to see if the same auto-cruise control
Function −How to Read Diagnostic Trouble system DTC will set again. (Refer to P.17-11,
Codes). Diagnostic Function −How to Read Diagnostic
4. If you can verify the condition but no auto-cruise Trouble Codes).
control system DTCs are set, the malfunction may • If the same auto-cruise control system DTC sets
be intermittent. (Refer to GROUP 00, How to Use again, perform the diagnostic procedures for the
Troubleshooting/Inspection Service Points −How set code. (Refer to P.17-15, Diagnostic Trouble
to Cope with Intermittent Malfunctions P.00-14). Code Chart).
DIAGNOSTIC FUNCTION
M1172004900193
HOW TO CONNECT THE SCAN TOOL (MUT-III).

• MB991824: Vehicle Communication Interface (V.C.I.)
CAUTION
DATA LINK
1. Ensure that the ignition switch is at the "LOCK" (OFF)
position.
2. Start up the personal computer.
3. Connect special tool MB991827 to special tool MB991824
MB991910 4. Connect special tool MB991910 to special tool MB991824.
MB991824 5. Connect special tool MB991910 to the data link connector.
6. Turn the power switch of special tool MB991824 to the "ON"
position.
tool MB991824 indicator light will be illuminated in green
color.
7. Start the MUT-III system on the personal computer.
NOTE: Disconnecting scan tool MB991958 is the reverse of
MB991827 the connecting sequence, making sure that the ignition
AC404789AB
switch is at the "LOCK" (OFF) position.
TSB Revision
AUTO-CRUISE CONTROL
HOW TO READ DIAGNOSTIC TROUBLE CODES

"CRUISE"
1. Turn the ignition switch to the "ON" position while holding
(ACC/RES) the auto-cruise control switch down to the "COAST/SET"
SWITCH: position. Then, within one second, more the cruise control
"ON" switch up to the "ACC/RES" position.
2. Read a diagnostic trouble code by observing the flash
"CRUISE" display pattern of the "CRUISE" indicator light in the
(COAST/
combination meter.
SET)
AUTO-CRUISE SWITCH:
CONTROL "ON"
SWITCH ACX01172 AH
DIAGNOSTIC RESULT DISPLAY METHOD WHEN USING THE "CRUISE" INDICATOR LIGHT
WHEN THE DIAGNOSTIC TROUBLE CODE NO.15 IS WHEN NO DIAGNOSTIC TROUBLE

OUTPUT CODE IS OUTPUT
0.5 s
0.5 s
1s
12V
12V
0V
0V
CONTINUOUS ON AND OFF
SIGNALS AT INTERVALS OF 0.5 s
PAUSE TEN- DIGIT FIRST DIGIT
TIME: 3 s DIGIT DIVISION: ACX01174 AB
2s
AC500348 AB
NOTE: Other on-board diagnostic items are also output as voltage waveforms corresponding to diagnostic
trouble code numbers.
TSB Revision
AUTO-CRUISE CONTROL
17-13
HOW TO ERASE DIAGNOSTIC TROUBLE CODES
NOTE: The diagnostic trouble code will not be erased even if
the negative battery terminal is disconnected.
"CRUISE"
1. Turn the ignition switch to the "ON" position while holding
(ACC/RES) the auto-cruise control switch down to the "COAST/SET"
SWITCH: position. Then, within one second, more the cruise control
"ON" switch up to the "ACC/RES" position.
2. Check to make sure the "CRUISE" indicator light on the
instrument panel is flashing.
"CRUISE" 3. Put the auto-cruise control switch to the "COAST/SET"
(COAST/SET) position. Depress the brake pedal and hold for five seconds
SWITCH: or more. Release the brake pedal, auto-cruise control
AUTO-CRUISE
"ON"
CONTROL SWITCH switch, then turn the ignition switch to the "LOCK" (OFF)
position. The DTC are now erased.
STOPLIGHT SWITCH
ON POSITION
BRAKE PEDAL
ACX02250 AC
HOW TO READ DATA LIST

• MB991824: V.C.I.
TSB Revision
AUTO-CRUISE CONTROL
CAUTION
DATA LINK
1. Connect scan tool MB991958 to the data link connector.
2. Turn the ignition switch to the "ON" position.
3. Select the "Interactive Diagnosis" from the start-up screen.
4. Select the "System Select."
5. Choose the "Auto-cruise Control System" from the
MB991910
"POWERTRAIN" tab.
MB991824 6. Select the "Data List."
7. Choose an appropriate item.
8. Turn the ignition switch to the "LOCK" (OFF) position.
9. Disconnect scan tool MB991958.
MB991827
AC404789AB
HOW TO DIAGNOSE THE CAN BUS LINE

• MB991824: V.C.I.
CAUTION
DATA LINK
1. Connect scan tool MB991958 to the data link connector.
3. Select the "CAN bus diagnosis" from the start-up screen.
4. When the vehicle information is displayed, confirm that it
matches the vehicle whose CAN bus lines will be
MB991910 diagnosed.
MB991824
• If the information is correct, go to step 8.
• If not, go to step 5.
5. Select the "view vehicle information" button.
6. Enter the vehicle information and select the "OK" button.
7. When the vehicle information is displayed, confirm again
that it matches the vehicle which is diagnosed CAN bus line.
• If they match, go to step 8.
• If not, go to step 5.
8. Press the "OK" button.
MB991827
AC404789AB 9. When the optional equipment screen is displayed, choose
the one which the vehicle is fitted with, and then select the
"OK" button.
TSB Revision
AUTO-CRUISE CONTROL
17-15
10.Turn the ignition switch to the "LOCK" (OFF) position.
11.Disconnect scan tool MB991958.
DIAGNOSTIC TROUBLE CODE CHART
M1172002200422
Check according to the inspection chart that is
appropriate for the diagnostic trouble code.
DIAGNOSTIC TROUBLE INSPECTION ITEM REFERENCE PAGE
CODE NO.
15 Auto-cruise control switch system P.17-15
22 Stoplight switch system P.17-32
23 ECM <M/T> or PCM <A/T> and its related P.17-51
components
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC P15: Auto-cruise Control Switch System
Auto-cruise Control Switch System Circuit
AUTO-CRUISE
CONTROL
SWITCH
BLACK-
BLACK
WHITE
CLOCK
SPRING
BLACK-
WHITE
RED
BLACK-
WHITE
RED
ECM <M/T> OR PCM <A/T>

AC407003 AB
TSB Revision
AUTO-CRUISE CONTROL
CONNECTORS: B-18, B-19 CONNECTOR: C-24
ECM <M/T>
OR
PCM <A/T>
B-18 (B)
B-19
AIR CLEANER
C-24
B-18 HARNESS B-19 HARNESS

CONNECTOR: CONNECTOR:
COMPONENT SIDE COMPONENT SIDE C-24 MALE SIDE CONNECTOR
AC407016 AB AC406808 AB
CONNECTORS: C-302, C-303, C-306
CLOCK SPRING
C-302 (Y)
C-306
C-303 (GR)
C-302 HARNESS C-303 HARNESS

COMPONENT SIDE COMPONENT SIDE
C-306 HARNESS
CONNECTOR:
COMPONENT SIDE
AC406809 AB
• When the "CRUISE" (MAIN) switch is "ON": 0 −

.
CIRCUIT OPERATION 0.3 volt

This circuit judges the signals of each switch • When the "COAST/SET" switch is ON: 2.0 −2.8
("COAST/SET", "ACC/RES" and "CANCEL") of the volts
auto-cruise control switch. The ECM <M/T> or PCM • When the "ACC/RES" switch is ON: 3.3 − 4.1
<A/T> detects the state of the auto-cruise control volts
switch by sensing the voltages shown below. • When the "CANCEL" switch is ON: 0.8 −1.5 volts
• When all switches are OFF: 4.7 − 5.0 volts
.
TSB Revision
AUTO-CRUISE CONTROL
17-17
DTC SET CONDITIONS
.

Check Condition LIKELY CAUSES FOR THIS CASE:)
• The "CRUISE" indicator light illuminates. • Malfunction of the auto-cruise control switch.
Judgement Criteria • Malfunction of the clock spring.
• If the auto-cruise control switch is operated, this • Damaged harness or connector.
DTC will be set when the ECM <M/T> or PCM • Malfunction of the ECM <M/T> or PCM <A/T>.
<A/T> terminal voltage is different from the stan-
dard value.
DIAGNOSIS
• MB991824: V.C.I.
• MB991223: Harness Set
• MB992006: Extra Fine Probe
• MB991923: Power Plant ECU Check Harness
TSB Revision
AUTO-CRUISE CONTROL
STEP 1. Using scan tool MB991958, check data list item 86:
Main switch, list item 92: Set switch, item 91: Resume
switch and list item 75: Cancel switch.
CAUTION
DATA LINK
(1) Connect scan tool MB991958 to the data link connector.
(Refer to P.17-11).
(3) Set scan tool MB991958 to data reading mode for
auto-cruise control system. (Refer to P.17-11).
• Item 86: Main switch.
MB991910
• When "CRUISE" (MAIN) switch is at the "ON" posi-
MB991824 tion, the display on scan tool MB991958 should be
"ON".
• When "CRUISE" (MAIN) switch is at the "OFF" posi-
tion, the display on scan tool MB991958 should be
"OFF".
• Item 92: Set switch.
• When "COAST/SET" switch is at the "ON" position,
the display on scan tool MB991958 should be "ON".
• When "COAST/SET" switch is at the "OFF" position,
MB991827
AC404789AB
the display on scan tool MB991958 should be
"OFF".
• Item 91: Resume switch.
• When "ACC/RES" switch is at the "ON" position, the
display on scan tool MB991958 should be "ON".
• When "ACC/RES" switch is at the "OFF" position,
the display on scan tool MB991958 should be
"OFF".
• Item 75: Cancel switch.
• When "CANCEL" switch is at the "ON" position, the
display on scan tool MB991958 should be "ON".
• When "CANCEL" switch is at the "OFF" position, the
display on scan tool MB991958 should be "OFF".
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is the switch operating properly?
YES : Go to Step 17.
NO : Go to Step 2.
TSB Revision
AUTO-CRUISE CONTROL
17-19
STEP 2. Measure the power supply voltage at auto-cruise

control switch connector C-302 by backprobing.
(1) Remove the air bag module (driver’s side). (Refer to
GROUP 52B, Air Bag Modules and Clock Spring
P.52B-408).
(2) Connect the negative (−) battery cable.
CONNECTOR: C-302 (3) Do not disconnect auto-cruise control switch connector
CLOCK C-302.
SPRING
C-302 (Y) (5) The "CRUISE" (MAIN) switch to the "OFF" position.
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
AC406803AB
C-302 HARNESS (6) Measure the power supply voltage between auto-cruise
CONNECTOR: control switch connector C-302 terminal 2 and ground by
HARNESS SIDE backprobing.
1 2 3
Q: Is the measured voltage between 4.7 and 5.0 volts?
YES : Go to Step 9.
NO : Go to Step 3.
AC205053 AC
TSB Revision
AUTO-CRUISE CONTROL
STEP 3. Measure the power supply voltage at ECM <M/T>

or PCM <A/T> connector B-18.
CONNECTOR: B-18
(1) Disconnect all the connectors from the ECM <M/T> or PCM
<A/T>.
ECM <M/T>
OR
PCM <A/T>
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AC
BODY SIDE ECM <M/T> OR (2) Connect special tool MB991923 between the ECM <M/T>
HARNESS B-18 (B) PCM <A/T> or PCM <A/T> and the body-side harness connector.
(4) The "CRUISE" (MAIN) switch to the "OFF" position.
MB991923
SPECIAL TOOL 18-PIN CONNECTOR

[ECM <M/T> OR PCM <A/T>
CONNECTOR B-18]
4 3 2 1
7 6 5
11 10 8 9
14 13 12
18 17 16 15 AC209793AU
TSB Revision
AUTO-CRUISE CONTROL
17-21
(5) Measure the power supply voltage between special tool
SPECIAL TOOL 18-PIN
CONNECTOR: 18-pin connector terminal 12 (ECM <M/T> or PCM <A/T>
COMPONENT SIDE connector B-18 terminal 12) and ground.
(7) Disconnect special tool MB991923 between the ECM
<M/T> or PCM <A/T> and the body-side harness connector.
(8) Reconnect all the connectors to the ECM <M/T> or PCM
<A/T>.
Q: Is the measured voltage between 4.7 and 5.0 volts?
AC209616AB YES : Go to Step 6.
NO : Go to Step 4.
STEP 4. Check ECM <M/T> or PCM <A/T> connector B-18

for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
CONNECTOR: B-18
Q: Are the connector and terminals in good condition?
YES : Go to Step 5.
NO : Repair or replace the faulty connector. (Refer to
GROUP 00E, Harness Connector Inspection
ECM <M/T> P.00E-2). Install the air bag module (driver’s side).
OR
PCM <A/T> (Refer to GROUP 52B, Air Bag Modules and Clock
Spring P.52B-408). Then go to Step 18.
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AC
TSB Revision
AUTO-CRUISE CONTROL
STEP 5. Check the harness for short circuit to ground

between the ECM <M/T> or PCM <A/T> connector B-18
terminal 12 and the auto-cruise control switch connector
C-302 terminal 2.
CONNECTOR: B-18
(1) Disconnect ECM <M/T> or PCM <A/T> connector B-18 and
measure at the harness connector side.
ECM <M/T>
OR
PCM <A/T>
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AC
B-18 HARNESS
(3) Measure the continuity between ECM <M/T> or PCM <A/T>
CONNECTOR: connector B-18 terminal 12 and ground.
COMPONENT SIDE (4) Reconnect ECM <M/T> or PCM <A/T> connector B-18.
Q: Is the measured continuity open circuit?
YES : Install the air bag module (driver’s side). (Refer to
P.52B-408). Then go to Step 17.
NO : Go to Step 6.
AC209263AE
TSB Revision
AUTO-CRUISE CONTROL
17-23
STEP 6. Check intermediate connector C-24, auto-cruise

control switch connector C-302 and clock spring
connectors C-303 and C-306 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
CONNECTOR: C-24 Q: Are the connectors and terminals in good condition?
YES : Go to Step 7.
P.00E-2). Install the air bag module (driver’s side).
(Refer to GROUP 52B, Air Bag Modules and Clock
C-24
C-24 MALE SIDE CONNECTOR
AC406808 AB
CONNECTORS: C-302, C-303, C-306
CLOCK SPRING
C-302 (Y)
C-306
C-303 (GR)

C-306 HARNESS
CONNECTOR:
COMPONENT SIDE
AC406809 AB
TSB Revision
AUTO-CRUISE CONTROL
STEP 7. Check the harness wire between ECM <M/T> or

PCM <A/T> connector B-18 terminal 12 and auto-cruise
control switch connector C-302 terminal 2 for damage.
CONNECTOR: B-18
Q: Are the harness wires in good condition?
YES : Go to Step 8.
NO : Repair the damaged harness wire and install the air
bag module (driver’s side). (Refer to GROUP 52B, Air
ECM <M/T> Bag Modules and Clock Spring P.52B-408). Then go
OR to Step 18.
PCM <A/T>
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AC
CONNECTOR: C-302
CLOCK
SPRING
C-302 (Y)
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
AC406803AB
STEP 8. Check the clock spring.

Refer to GROUP 52B, Air Bag Modules and Clock Spring
P.52B-414.
Q: Is the clock spring in good condition?
YES : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points −How to
Cope with Intermittent Malfunction P.00-14). Install
the air bag module (driver’s side). (Refer to GROUP
52B, Air Bag Modules and Clock Spring P.52B-408).
Then go to Step 18.
NO : Replace the clock spring and install the air bag
module (driver’s side). (Refer to GROUP 52B, Air Bag
Modules and Clock Spring P.52B-408). Then go to
Step 18.
TSB Revision
AUTO-CRUISE CONTROL
17-25
STEP 9. Measure the ground voltage at auto-cruise control

switch connector C-302 by backprobing.
CONNECTOR: C-302 (1) Do not disconnect auto-cruise control switch connector
CLOCK C-302.
SPRING
C-302 (Y) (3) Turn the "CRUISE" (MAIN) switch to the "ON" position.
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
AC406803AB
(4) Measure the ground voltage between auto-cruise control

C-302 HARNESS
CONNECTOR:
switch connector C-302 terminal 3 and ground by
HARNESS SIDE backprobing.
(5) Turn the "CRUISE" (MAIN) switch to the "OFF" position.
1 2 3 (6) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage 0.5 volt or less?
NO : Go to Step 10.
AC209264 AB
TSB Revision
AUTO-CRUISE CONTROL
STEP 10. Measure the ground voltage at ECM <M/T> or

PCM <A/T> connector B-19.
CONNECTOR: B-19 (1) Disconnect all the connectors from the ECM <M/T> or PCM
<A/T>.
ECM <M/T>
OR
PCM <A/T>
B-19
AIR CLEANER
B-19 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AD
HARNESS PCM <A/T> or PCM <A/T> and the body-side harness connector.
B-19 (4) Turn the "CRUISE" (MAIN) switch to the "ON" position.
MB991923

WITHOUT RED TAPE
[ECM <M/T> OR PCM <A/T> CONNECTOR
B-19]
25 24 23 22 21
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39 AC209793AV
TSB Revision
AUTO-CRUISE CONTROL
17-27
SPECIAL TOOL 23-PIN
(5) Measure the ground voltage between special tool 23-pin
CONNECTOR connector (without red tape) terminal 28 (ECM <M/T> or
(WITHOUT RED TAPE): PCM <A/T> connector B-19 terminal 28) and ground.
COMPONENT SIDE (6) Turn the "CRUISE" (MAIN) switch to the "OFF" position.
(8) Disconnect special tool MB991923 between the ECM
<A/T>.
AC209615 AB Q: Is the measured voltage 0.5 volt or less?
NO : Go to Step 11.

for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
CONNECTOR: B-19 Q: Are the connector and terminals in good condition?
YES : Install the air bag module (driver’s side). (Refer to
P.52B-408). Then go to Step 17.
ECM <M/T> NO : Repair or replace the faulty connector. (Refer to
OR
PCM <A/T> GROUP 00E, Harness Connector Inspection
B-19
AIR CLEANER
B-19 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AD
TSB Revision
AUTO-CRUISE CONTROL
STEP 12. Check ECM <M/T> or PCM <A/T> connector B-19,

intermediate connector C-24, auto-cruise control switch
connector C-302 and clock spring connectors C-303 and
C-306 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
CONNECTOR: B-19
ECM <M/T>
OR
PCM <A/T>
B-19
AIR CLEANER
B-19 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AD
CONNECTOR: C-24
C-24
AC406808 AB
TSB Revision
AUTO-CRUISE CONTROL
17-29
CONNECTORS: C-302, C-303, C-306 Q: Are the connectors and terminals in good condition?
CLOCK SPRING GROUP 00E, Harness Connector Inspection
C-302 (Y) P.00E-2). Install the air bag module (driver’s side).
C-306 Spring P.52B-408). Then go to Step 18.
C-303 (GR)

C-306 HARNESS
CONNECTOR:
COMPONENT SIDE
AC406809 AB
TSB Revision
AUTO-CRUISE CONTROL

PCM <A/T> connector B-19 terminal 28 and auto-cruise
control switch connector C-302 terminal 3 for damage.
CONNECTOR: B-19 Q: Are the harness wires in good condition?
NO : Repair the damaged harness wire and install the air
bag module (driver’s side). (Refer to GROUP 52B, Air
ECM <M/T> Bag Modules and Clock Spring P.52B-408). Then go
OR to Step 18.
PCM <A/T>
B-19
AIR CLEANER
B-19 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AD
CONNECTOR: C-302
CLOCK
SPRING
C-302 (Y)
C-302 HARNESS
CONNECTOR:
COMPONENT SIDE
AC406803AB
STEP 14. Check the clock spring.

Refer to GROUP 52B, Air Bag Modules and Clock Spring
P.52B-414.
Q: Is the clock spring in good condition?
Cope with Intermittent Malfunction P.00-14). Install
the air bag module (driver’s side). (Refer to GROUP
52B, Air Bag Modules and Clock Spring P.52B-408).
Then go to Step 18.
NO : Replace the clock spring and install the air bag
module (driver’s side). (Refer to GROUP 52B, Air Bag
Modules and Clock Spring P.52B-408). Then go to
Step 18.
TSB Revision
AUTO-CRUISE CONTROL
17-31
STEP 15. Check auto-cruise control switch connector

C-302 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
CONNECTOR: C-302 Q: Are the connector and terminals in good condition?
CLOCK YES : Go to Step 16.
SPRING
C-302 (Y) GROUP 00E, Harness Connector Inspection
C-302 HARNESS Spring P.52B-408). Then go to Step 18.
CONNECTOR:
COMPONENT SIDE
AC406803AB
STEP 16. Check the auto-cruise control switch.

(1) Remove the steering wheel assembly. (Refer to GROUP
37, Steering Wheel P.37-27).
(2) Measure the resistance between terminal 2 and terminal 3
when each of the "CRUISE" (MAIN), "COAST/SET",
AUTO-CRUISE
CONTROL "ACC/RES" and "CANCEL" switch is pressed.
SWITCH
SWITCH POSITION SPECIFIED CONDITION
"CRUISE" (MAIN) switch Open circuit
5 4 3 2 1 "OFF"
"CRUISE" (MAIN) switch Less than 2 ohms
"ON"
2
AC406783 "CANCEL" switch ON Approximately 100 Ω
"ACC/RES" switch ON Approximately 887 Ω
"COAST/SET" switch ON Approximately 300 Ω
Q: Is the resistance within specifications?

MAIN RES SET CAN YES : Install the air bag module (driver’s side). (Refer to
OFF OFF OFF OFF GROUP 52B, Air Bag Modules and Clock Spring
ON ON ON ON P.52B-408). Then go to Step 17.
NO : Replace the auto-cruise control switch. (Refer to
3 AC406784 AB P.17-89). Install the air bag module (driver’s side).
STEP 17. Read the diagnostic trouble code.

Read the diagnostic trouble codes. (Refer to P.17-11).
Q: Is DTC P15 set?
YES : Replace the ECM <M/T> or PCM <A/T>. (Refer to
GROUP 54A, Immobilizer System −Encrypted Code
Registration Criteria Table P.54A-13). Then go to Step
18.
NO : It can be assumed that this malfunction is intermittent.
Cope with Intermittent Malfunction P.00-14).
TSB Revision
AUTO-CRUISE CONTROL

Q: Is DTC P15 set?
YES : Return to Step 1.
NO : The procedure is complete.
DTC 22: Stoplight Switch System
Stoplight Switch System Circuit
BATTERYWHITE
WHITE
RELAY
BOX
GREEN-
BLACK
STOPLIGHT
SWITCH
BLACK
GREEN
LIGHT GREEN-
BLACK
BLACK
JOINT GREEN
CONNECTOR (1) STOPLIGHT
GREEN
ECM <M/T> OR PCM <A/T>

AC407004 AB
TSB Revision
AUTO-CRUISE CONTROL
17-33
CONNECTORS: B-18, B-19 CONNECTORS: C-28, C-103
C-28 C-103
ECM <M/T>
OR
PCM <A/T>
B-18 (B)
B-19
AIR CLEANER
B-18 HARNESS B-19 HARNESS

CONNECTOR: CONNECTOR: C-28 HARNESS C-103
C-103HARNESS
HARNESS
CONNECTOR:
CONPONENT SIDE COMPONENT
CONPONENTSIDE
SIDE
AC407016 AB AC406808 AC
Judgement Criteria
.
CIRCUIT OPERATION • Short in stop light switch circuit.

• Battery positive voltage is supplied to the stop- • Open circuit in the brake switch circuit (between
light switch (terminal 2 and 3). ECM <M/T> or PCM <A/T> terminal 33 and
• When the brake pedal is depressed, battery posi- ground).
tive voltage is applied to the ECM <M/T> or PCM
<A/T> (terminal 9 and 33). .

LIKELY CAUSES FOR THIS CASE:)
.
DTC SET CONDITIONS

• Malfunction of the stoplight switch.
Check Condition • Damaged harness or connector.
• The "CRUISE" indicator light illuminates. • Malfunction of the ECM <M/T> or PCM <A/T>.
DIAGNOSIS
• MB991824: V.C.I.
TSB Revision
AUTO-CRUISE CONTROL
Brake light switch.
CAUTION
DATA LINK
(Refer to P.17-11).
• Item 74, Brake light switch.
MB991910
• When the brake pedal is depressed, the display on
MB991824 scan tool MB991958 should be "ON".
• When the brake pedal is released, the display on
scan tool MB991958 should be "OFF".
NO : Go to Step 2.
MB991827
AC404789AB
STEP 2. Check the stoplight operation.

Check the stoplight operation.
• When the brake pedal is depressed, the stoplight will
illuminate.
• When the brake pedal is released, the stoplight does not
illuminate.
Q: Does the stoplight illuminate when the brake pedal is
depressed and go out when the brake pedal is
released?
YES : Go to Step 3.
NO : Go to Step 6.
TSB Revision
AUTO-CRUISE CONTROL
17-35
STEP 3. Measure the terminal voltage at ECM <M/T> or

CONNECTOR: B-18
(1) Disconnect all the connectors from the ECM <M/T> or PCM
<A/T>.
ECM <M/T>
OR
PCM <A/T>
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AC
HARNESS B-18 (B) PCM <A/T> or PCM <A/T> and the body-side harness connector.
MB991923

[ECM <M/T> OR PCM <A/T>
CONNECTOR B-18]
4 3 2 1
7 6 5
11 10 8 9
14 13 12
18 17 16 15 AC209793AU
TSB Revision
AUTO-CRUISE CONTROL
(4) Measure the terminal voltage between special tool 18-pin

SPECIAL TOOL 18-PIN
CONNECTOR:
connector terminal 9 (ECM <M/T> or PCM <A/T> connector
COMPONENT SIDE B-18 terminal 9) and ground.
• When the brake pedal is depressed, the voltage should
measure battery positive voltage (approximately 12
volts).
• When the brake pedal is released, the voltage should
measure 1 volt or less.
AC209617AB (6) Disconnect special tool MB991923 between the ECM
<A/T>.
Q: Is the measured voltage battery positive voltage
(approximately 12 volts) when the brake pedal is
depressed and 1 volt or less when the brake pedal is
released?
NO : Go to Step 4.
TSB Revision
AUTO-CRUISE CONTROL
17-37

and joint connector (1) C-28 for loose, corroded or
connector.
CONNECTOR: B-18
Q: Are the connectors and terminals in good condition?
YES : Go to Step 5.
NO : Repair or replace the damaged components. (Refer to
ECM <M/T> P.00E-2). Then go to Step 22.
OR
PCM <A/T>
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AC
CONNECTOR: C-28
C-28
C-28 HARNESS
CONNECTOR:
CONPONENT SIDE
AC406808 AD
TSB Revision
AUTO-CRUISE CONTROL

PCM <A/T> connector B-18 terminal 9 and joint connector
(1) C-28 terminal 14 for damage.
CONNECTOR: B-18
Q: Is the harness wire in good condition?
NO : Repair the damaged harness wire. Then go to Step
22.
ECM <M/T>
OR
PCM <A/T>
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AC
CONNECTOR: C-28
C-28
C-28 HARNESS
CONNECTOR:
CONPONENT SIDE
AC406808 AD
TSB Revision
AUTO-CRUISE CONTROL
17-39
STEP 6. Measure the power supply voltage at stoplight

switch connector C-103 by backprobing.
CONNECTOR: C-103 (1) Disconnect stoplight switch connector C-103.
C-103
C-103
C-103HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AE
C-103 HARNESS
(2) Measure the power supply voltage between stoplight switch
CONNECTOR: connector C-103 terminal 2 and ground.
COMPONENT SIDE (3) Reconnect stoplight switch connector C-103.
(approximately 12 volts)?
NO : Go to Step 7.
AC305712AG
TSB Revision
AUTO-CRUISE CONTROL
STEP 7. Check stoplight switch connector C-103 for loose,

corroded or damaged terminals, or terminals pushed back
in the connector.
CONNECTOR: C-103 Q: Are the connector and terminals in good condition?
YES : Go to Step 8.
C-103 GROUP 00E, Harness Connector Inspection
P.00E-2). Then go to Step 22.
C-103
C-103HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AE
TSB Revision
AUTO-CRUISE CONTROL
17-41
STEP 8. Check the harness wire between stoplight switch

connector C-103 terminal 2 and fuse number 11 at the relay
box at engine compartment for damage.
CONNECTOR: C-103 Q: Is the harness wire in good condition?
YES : Go to Step 9.
C-103 22.
C-103
C-103HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AE
BATTERY
FUSE NUMBER 11
(HOUSING COLOR:
BROWN)
RELAY BOX
AC406987 AB
STEP 9. Check the fuse number 11 at the relay box at

engine compartment.
BATTERY Q: Is the fuse in good condition?
FUSE NUMBER 11 YES : Go to Step 10.
(HOUSING COLOR: NO : Check the stoplight system harness and replace the
BROWN) fuse. Then go to Step 22.
RELAY BOX
AC406987 AB
TSB Revision
AUTO-CRUISE CONTROL
STEP 10. Check the stoplight switch.

(1) Remove the stoplight switch. (Refer to GROUP 35A, Brake
Pedal P.35A-25).
(2) Connect an ohmmeter to the stoplight switch between
terminals 1 and 2.
(3) Check for continuity between the terminals when the
plunger of the stoplight switch is pushed in and when it is
released.
(4) The stoplight switch is operating properly if the circuit is
open between terminals 1 and 2 when the plunger is
pushed in to a depth of within 4.0 mm (0.16 inch) from the
C-103 STOPLIGHT SWITCH outer case edge surface, and if the resistance value is less
CONNECTOR ACX02256 AO than 2 ohms between terminals 1 and 2 when it is released.
Q: Is the stoplight switch operating properly?
NO YES : Install the stoplight switch. (Refer to GROUP 35A,
CONTINUITY CONTINUITY Brake Pedal P.35A-25). Then go to Step 11.
NO : Replace the stoplight switch. (Refer to GROUP 35A,
Brake Pedal P.35A-25). Then go to Step 22.
4.0 mm (0.16 in)

AC205057 AB
STEP 11. Check stoplight switch connector C-103 and joint

connector (1) C-28 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
CONNECTORS: C-28, C-103 Q: Are the connectors and terminals in good condition?
C-28 C-103 GROUP 00E, Harness Connector Inspection
C-28 HARNESS C-103

C-103HARNESS
HARNESS
CONNECTOR:
CONPONENTSIDE
SIDE
AC406808 AC
TSB Revision
AUTO-CRUISE CONTROL
17-43

connector C-103 terminal 1 and joint connector (1) C-28
terminal 12 for damage.
CONNECTORS: C-28, C-103 Q: Is the harness wire in good condition?
C-28 C-103 22.
C-28 HARNESS C-103

C-103HARNESS
HARNESS
CONNECTOR:
CONPONENTSIDE
SIDE
AC406808 AC
STEP 13. Using scan tool MB991958, check data list item
74: Brake light switch.
CAUTION
DATA LINK
(Refer to P.17-11).
MB991910
NO : Replace the ECM <M/T> or PCM <A/T>. (Refer to
MB991827
AC404789AB Registration Criteria Table P.54A-13). Then go to Step
22.
TSB Revision
AUTO-CRUISE CONTROL
89: Normally closed brake switch.
CAUTION
DATA LINK
(Refer to P.17-11).
• Item 89, Normally closed brake switch.
MB991910
NO : Go to Step 15.
MB991827
AC404789AB
TSB Revision
AUTO-CRUISE CONTROL
17-45
STEP 15. Measure the terminal voltage at ECM <M/T> or

CONNECTOR: B-19 (1) Disconnect all the connectors from the ECM <M/T> or PCM
<A/T>.
ECM <M/T>
OR
PCM <A/T>
B-19
AIR CLEANER
B-19 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AD
HARNESS PCM <A/T> or PCM <A/T> and the body-side harness connector.
B-19
MB991923

WITHOUT RED TAPE
[ECM <M/T> OR PCM <A/T> CONNECTOR
B-19]
25 24 23 22 21
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39 AC209793AV
TSB Revision
AUTO-CRUISE CONTROL

SPECIAL TOOL 23-PIN
CONNECTOR connector (without red tape) terminal 33 (ECM <M/T> or
(WITHOUT RED TAPE): PCM <A/T> connector B-19 terminal 33) and ground.
COMPONENT SIDE • When the brake pedal is depressed, the voltage should
measure battery positive voltage (approximately 12
volts).
• When the brake pedal is released, the voltage should
measure 1 volt or less.
AC209671AB (6) Disconnect special tool MB991923 between the ECM
<M/T> or PCM and the body-side harness connector.
(7) Reconnect all the connectors to the ECM <M/T> or PCM.
(approximately 12 volts) when the brake pedal is
depressed and 1 volt or less when the brake pedal is
released?
NO : Go to Step 16.
STEP 16. Check the stoplight switch.

(1) Remove the stoplight switch. (Refer to GROUP 35A, Brake
Pedal P.35A-25).
(2) Connect an ohmmeter to the stoplight switch between
C-103 STOPLIGHT SWITCH
terminals 3 and 4.
CONNECTOR
1 2 plunger of the stoplight switch is pushed in and when it is
3 4 released.
(4) The stoplight switch is operating properly if the circuit is
open between terminals 3 and 4 when the plunger is
released, and if resistance value is less than 2 ohms
between terminals 3 and 4 when the plunger is pushed in to
ACX01917AM
a depth of within 4.5 mm (0.18 inch) from the outer case
edge surface.
NO Q: Is the stoplight switch operating properly?
CONTINUITY CONTINUITY YES : Install the stoplight switch. (Refer to GROUP 35A,
NO : Replace the stoplight switch. (Refer to GROUP 35A,
4.5 mm (0.18 in)

AC205057AC
TSB Revision
AUTO-CRUISE CONTROL
17-47

and stoplight switch connector C-103 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
CONNECTOR: B-19 Q: Are the connectors and terminals in good condition?
ECM <M/T> P.00E-2). Then go to Step 22.
OR
PCM <A/T>
B-19
AIR CLEANER
B-19 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AD
CONNECTOR: C-103
C-103
C-103
C-103HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AE
TSB Revision
AUTO-CRUISE CONTROL

PCM <A/T> connector B-19 terminal 33 and stoplight
switch connector C-103 terminal 3 for damage.
CONNECTOR: B-19 Q: Is the harness wire in good condition?
22.
ECM <M/T>
OR
PCM <A/T>
B-19
AIR CLEANER
B-19 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AD
CONNECTOR: C-103
C-103
C-103
C-103HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AE
TSB Revision
AUTO-CRUISE CONTROL
17-49

connector C-103 terminal 4 and ground for damage.
C-103 22.
C-103
C-103HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AE
RELAY BOX
GROUND
TERMINAL AC406990 AB
TSB Revision
AUTO-CRUISE CONTROL
89: Normally closed brake switch.
CAUTION
DATA LINK
(Refer to P.17-11).
MB991910
MB991827
AC404789AB Registration Criteria Table P.54A-13). Then go to Step
22.
STEP 21. Read the diagnostic trouble codes.

Q: Is DTC P22 set?
22.
STEP 22. Read the diagnostic trouble codes.

Q: Is DTC P22 set?
TSB Revision
AUTO-CRUISE CONTROL
17-51
DTC P23: ECM <M/T> or PCM <A/T> and Its Related Component

.
DTC SET CONDITIONS

This DTC is set when there is an failure in the ECM LIKELY CAUSES FOR THIS CODE TO BE
<M/T> or PCM <A/T> and its related components. SET ARE:)
.
• Malfunction of the MFI system.
• Malfunction of the A/T system <A/T>.
DIAGNOSIS
• MB991824: V.C.I.
STEP 1. Using scan tool MB991958, read the MFI system

diagnostic trouble code.
CAUTION
DATA LINK
(Refer to P.17-11).
Read and Erase Diagnostic Trouble Code P.13A-6) <2.4L
MB991910
MB991824 Diagnostic Function −How to Read and Erase Diagnostic
Q: Is any DTC set?
YES : Diagnose the MFI system. (Refer to GROUP 13A,
MFI Diagnosis −Diagnostic Trouble Code Chart
MB991827 MFI Diagnosis −Diagnostic Trouble Code Chart
AC404789AB
NO : Go to Step 3 <M/T> or Step 2 <A/T>.
TSB Revision
AUTO-CRUISE CONTROL
STEP 2. Using scan tool MB991958, read the A/T system

diagnostic trouble code <A/T>.
CAUTION
DATA LINK
(Refer to P.17-11).
(3) Check for A/T system diagnostic trouble code. (Refer to
GROUP 23A, A/T Diagnosis −Diagnostic Function −How to
Read and Erase Diagnostic Trouble Code P.23A-16).
MB991910
MB991824 (5) Disconnect scan tool MB991958.
Q: Is any DTC set?
YES : Diagnose the A/T system. (Refer to GROUP 23A, A/T
Diagnosis −Diagnostic Trouble Code Chart
P.23A-64). Then go to Step 4.
NO : Go to Step 3.
MB991827
AC404789AB
STEP 3. Read the auto-cruise control system diagnostic

trouble code.
Read the auto-cruise control system diagnostic trouble codes.
(Refer to P.17-11).
Q: Is DTC P23 set?
4.

trouble code.
(Refer to P.17-11).
Q: Is DTC P23 set?
TSB Revision
AUTO-CRUISE CONTROL
17-53
SYMPTOM CHART
M1172002300548
SYMPTOM INSPECTION REFERENCE

PROCEDURE NO. PAGE
Communication with Communication with all systems is - Group 13A, MFI
scan tool is not impossible Diagnosis −
possible Symptom
Procedures −
Inspection
Procedure 1
P.13A-1011 <2.4L
engine>.
Group 13B, MFI
Diagnosis −
Symptom
Procedures −
Inspection
Procedure 1
P.13B-1085 <3.8L
engine>.
Communication with the ECM <M/T> or - Group 13A, MFI
PCM <A/T> only is impossible Diagnosis −
Symptom
Procedures −
Inspection
Procedure 2
P.13A-1014 <2.4L
engine>.
Group 13B, MFI
Diagnosis −
Symptom
Procedures −
Inspection
Procedure 2
P.13B-1088 <3.8L
engine>.
Auto-cruise control When brake pedal is depressed 1 P.17-54
system is not When clutch pedal is depressed <M/T> 2 P.17-55
cancelled.
When selector lever is moved to "N" 3 P.17-64
position <A/T>
When "CANCEL" switch is turned ON 4 P.17-68
Auto-cruise control system cannot be set. 5 P.17-68
Hunting (repeated acceleration and deceleration) occurs at the 6 P.17-72
set vehicle speed.
When "CRUISE" (MAIN) switch is turned "ON", "CRUISE" 7 P.17-75
indicator light inside combination meter does not illuminate.
(However, auto-cruise control system is normal).
TSB Revision
AUTO-CRUISE CONTROL
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: When the Brake Pedal is Depressed, Auto-cruise Control System is not
Cancelled.

.
COMMENT
The stoplight switch circuit is suspected. LIKELY CAUSES FOR THIS CASE:)
• Malfunction of the stoplight switch.
• Damaged harness or connector.
.
DIAGNOSIS

trouble code.
(Refer to P.17-11).
Q: Is DTC P15 set?
YES : Refer to P.17-15, Diagnostic Trouble Code
Procedures −DTC P15: Stoplight Switch System.
NO : Go to Step 2.
STEP 2. Check the symptoms.

Q: When the brake pedal is depressed, auto-cruise control
system is cancelled?
3.

Q: When the clutch pedal is depressed, auto-cruise control
system is cancelled?
TSB Revision
AUTO-CRUISE CONTROL
17-55
INSPECTION PROCEDURE 2: When Clutch Pedal is Depressed, Auto-cruise Control System is not
Cancelled <M/T>.
Clutch Pedal Position Switch Circuit
ECM
BROWN-BLACK
CLUTCH
PEDAL
POSITION
SWITCH
BLACK
BLACK
BLACK
AC407005 AB
TSB Revision
AUTO-CRUISE CONTROL
CONNECTOR: B-18 CONNECTOR: C-129
ECM
C-129
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR: C-103
C-129HARNESS
HARNESS
COMPONENT SIDE
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC407016 AE AC406808 AF
. .
CIRCUIT OPERATION COMMENT

This circuit judges the signals of clutch pedal position The clutch pedal position switch circuit is suspected.
switch. The ECM detects the state of the clutch pedal .
position switch by sensing the voltages shown below. TROUBLESHOOTING HINTS (THE MOST
• When the brake pedal is depressed (clutch pedal
position switch are OFF): 0 − 0.3 volt.
• When the brake pedal is released (clutch pedal • Malfunction of the clutch pedal position switch.
position switch are ON): 4.7 − 5.0 volts. • Damaged harness or connector.
• Malfunction of the ECM.
DIAGNOSIS
• MB991824: V.C.I.
TSB Revision
AUTO-CRUISE CONTROL
17-57
Clutch switch.
CAUTION
DATA LINK
(Refer to P.17-11).
• Item 78: Clutch switch.
MB991910
• When the clutch pedal is depressed, the display on
• When the clutch pedal is released, the display on
YES : Go to Step 7.
NO : Go to Step 2.
MB991827
AC404789AB
TSB Revision
AUTO-CRUISE CONTROL
STEP 2. Measure the terminal voltage at ECM connector

B-18.
CONNECTOR: B-18 (1) Disconnect all the connectors from the ECM.
ECM
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AE
BODY SIDE (2) Connect special tool MB991923 between the ECM and the
HARNESS B-18 (B) ECM body-side harness connector.
MB991923

(ECM CONNECTOR B-18)
4 3 2 1
7 6 5
11 10 8 9
14 13 12
18 17 16 15
AC209793AW
TSB Revision
AUTO-CRUISE CONTROL
17-59
SPECIAL TOOL 18-PIN
connector terminal 16 (ECM connector B-18 terminal 16)
CONNECTOR:
COMPONENT SIDE and ground.
• When the clutch pedal is depressed, the measured volt-
age is between 4.7 and 5.0 volts.
• When the brake pedal is released, the measured volt-
age is between 0 and 0.3 volt.
(6) Disconnect special tool MB991923 between the ECM and
AC406855 AB the body-side harness connector.
(7) Reconnect all the connectors to the ECM.
Q: Is the measured voltage between 4.7 and 5.0 volts when
the brake pedal is depressed and between 0 and 0.3 volt
when the brake pedal is released?
YES : Go to Step 7.
NO : Go to Step 3.
TSB Revision
AUTO-CRUISE CONTROL
STEP 3. Check ECM connector B-18 and clutch pedal

position switch connector C-129 for loose, corroded or
connector.
CONNECTOR: B-18 Q: Are the connectors and terminals in good condition?
YES : Go to Step 4.
ECM
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AE
CONNECTOR: C-129
C-129
C-103
C-129HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AF
TSB Revision
AUTO-CRUISE CONTROL
17-61
STEP 4. Check the harness wire between ECM connector

B-18 terminal 16 and clutch pedal position switch
connector C-129 terminal 2 for damage.
CONNECTOR: B-18 Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair the damaged harness wire. Then go to Step 8.
ECM
B-18 (B)
AIR CLEANER
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AC407016 AE
CONNECTOR: C-129
C-129
C-103
C-129HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AF
TSB Revision
AUTO-CRUISE CONTROL
STEP 5. Check the harness wire between clutch pedal

position switch connector C-129 terminal 1 and ground for
damage.
YES : Go to Step 6.
NO : Repair the damaged harness wire. Then go to Step 8.
C-129
C-103
C-129HARNESS
HARNESS
CONNECTOR:
CONNECTOR:
COMPONENT
CONPONENTSIDE
SIDE
AC406808 AF
RELAY BOX
GROUND
TERMINAL AC406990 AB
TSB Revision
AUTO-CRUISE CONTROL
17-63
STEP 6. Check the clutch pedal position switch.

(1) Remove the clutch pedal position switch. (Refer to GROUP
21A, Clutch Pedal P.21A-12).
(2) Connect an ohmmeter to the clutch pedal position switch
between terminals 1 and 2.
plunger of the clutch pedal position switch is pushed in and
when it is released.
(4) The clutch pedal position switch is operating properly if the
circuit is open between terminals 1 and 2 when the plunger
is pushed in to a depth of within 4.0 mm (0.16 inch) from the
C-129 CLUTCH PEDAL outer case edge surface, and if the resistance value is less
POSITION SWITCH CONNECTOR ACX02256 AP than 2 ohms between terminals 1 and 2 when it is released.
Q: Is the clutch pedal position switch operating properly?
NO YES : Install the clutch pedal position switch. (Refer to
CONTINUITY CONTINUITY GROUP 21A, Clutch Pedal P.21A-12). Then go to
Step 7.
NO : Replace the clutch pedal position switch. (Refer to
GROUP 21A, Clutch Pedal P.21A-12). Then go to
Step 8.
4.0 mm (0.16 in)

AC205057 AB

Q: When the clutch pedal is depressed, is auto-cruise
control cancelled?
NO : Replace the ECM. (Refer to GROUP 54A,
Immobilizer System −Encrypted Code Registration
Criteria Table P.54A-13). Then go to Step 8.

Q: When the clutch pedal is depressed, is auto-cruise
control cancelled?
TSB Revision
AUTO-CRUISE CONTROL
INSPECTION PROCEDURE 3: When the Selector Lever is Moved to "N" Position, Auto-cruise Control
System is not Cancelled <A/T>.
Transmission Range Switch Circuit
IGNITION
SWITCH (IG1)
RED
JUNCTION
BLOCK
BLACK-
WHITE
BLACK-
WHITE
JOINT
CONNECTOR (1)
BLACK-
WHITE
BLACK- BLACK-
WHITE WHITE
BLACK-
WHITE
TRANSMISSION
RANGE
SWITCH
RED-BLUE
PCM
AC407006 AB
TSB Revision
AUTO-CRUISE CONTROL
17-65
CONNECTOR: A-15 CONNECTOR: B-20
A-15 (GR)
PCM
B-20 (GR)
AIR CLEANER
B-20 HARNESS
CONNECTOR:
A-15 MALE SIDE CONNECTOR COMPONENT SIDE
AC406787 AB AC407016 AF
CONNECTOR: B-113 CONNECTORS: C-24,C-28
C-28
B-113 (B)
C-24
B-113 HARNESS CONNECTOR:

COMPONENT SIDE
C-28 HARNESS CONNECTOR:

CONPONENT SIDE
AC406788 AB AC406808 AH
TSB Revision
AUTO-CRUISE CONTROL
CONNECTORS: C-202, C-203

JUNCTION BLOCK
(FRONT VIEW)
C-202
C-203

COMPONENT SIDE

COMPONENT SIDE
AC406863 AC
. .
CIRCUIT OPERATION COMMENT

• Battery positive voltage is applied to the transmis- The transmission range switch circuit is suspected.
sion range switch (terminal 8) when the ignition .
switch is turned "ON." TROUBLESHOOTING HINTS (THE MOST

• Battery positive voltage is applied to the PCM ter-
minal 77 when the selector lever is in the "N"
range. The PCM judges that the selector lever is • Malfunction of the transmission range switch.
in the "N" range when the battery positive voltage • Damaged harness or connector.
is applied. • Malfunction of the PCM.
DIAGNOSIS
• MB991824: V.C.I.
TSB Revision
AUTO-CRUISE CONTROL
17-67
Neutral switch.
CAUTION
DATA LINK
(Refer to P.17-11).
• Item 88, Neutral switch.
MB991910
• When selector lever is at the "N" position, the display
MB991824 on scan tool MB991958 should be "ON".
• When selector lever is other than "N" position, the
YES : Go to Step 3.
NO : Go to Step 2.
MB991827
AC404789AB

CAUTION
DATA LINK
(Refer to P.17-11).
MB991910
Q: Is any DTC P1770 or P1771 set?
YES : Refer to GROUP 23A, A/T Diagnosis −Diagnostic
Trouble Code Procedures −DTC P1770:
Transmission Range Switch System (Open Circuit)
P.23A-143, DTC P1771: Transmission Range Switch
System (Short Circuit) P.23A-171. Then go to Step 4.
NO : Go to Step 3.
MB991827
AC404789AB
TSB Revision
AUTO-CRUISE CONTROL

Q: When the selector lever is moved to "N" position,
auto-cruise control system is cancelled?
NO : Replace the PCM. (Refer to GROUP 54A,
Immobilizer System −Encrypted Code Registration
Criteria Table P.54A-13). Then go to Step 4.

Q: When the selector lever is moved to "N" position,
auto-cruise control system is cancelled?
INSPECTION PROCEDURE 4: When the Auto-cruise Control "CANCEL" Switch is Set to ON,
Auto-cruise Control System is not Cancelled.
. .
COMMENT TROUBLESHOOTING HINTS (THE MOST

The cause is probably an open-circuit in the output in LIKELY CAUSES FOR THIS CASE:)
the circuit inside the "CANCEL" switch. • Malfunction of the auto-cruise control switch.
DIAGNOSIS
Replace the auto-cruise control switch. (Refer to P.17-89,
Auto-cruise Control).
INSPECTION PROCEDURE 5: Auto-cruise Control System cannot be Set.

. .
COMMENT TROUBLESHOOTING HINTS (THE MOST

The fail-safe function is probably canceling LIKELY CAUSES FOR THIS CASE:)
auto-cruise control system. In this case, checking the • Malfunction of the auto-cruise control switch.
diagnostic trouble codes. The scan tool MB991958 • Malfunction of the stoplight switch.
can also be used to check if the circuits of each input • Malfunction of the transmission range switch.
switch are normal or not by checking the input switch • Malfunction of the ECM <M/T> or PCM <A/T>.
codes.
DIAGNOSIS
• MB991824: V.C.I.
TSB Revision
AUTO-CRUISE CONTROL
17-69

Read the auto-cruise control system diagnostic trouble code.
(Refer to P.17-11).
Q: Is DTC set?
YES : Diagnose the auto-cruise control system. (Refer to
P.17-15, Diagnostic Trouble Code Chart). Then go to
Step 7.
NO : Go to Step 2.
Cancel switch.
CAUTION
DATA LINK
(Refer to P.17-11).
• Item 75, Cancel switch.
MB991910
• When "CANCEL" switch is at the ON position, the
MB991824 display on scan tool MB991958 should be "ON".
• When "CANCEL" switch is at the OFF position, the
YES : Go to Step 3.
NO : Refer to P.17-68, Symptom Procedures −Inspection
MB991827
Procedure 4. Then go to Step 7.
AC404789AB
TSB Revision
AUTO-CRUISE CONTROL
Brake light switch and data list item 89: Normally closed
brake switch.
CAUTION
DATA LINK
(Refer to P.17-11).
MB991910
• When brake pedal is depressed, the display on scan
MB991824 tool MB991958 should be "ON".
• When brake pedal is released, the display on scan
tool MB991958 should be "OFF".
• When brake pedal is depressed, the display on scan
tool MB991958 should be "ON".
• When brake pedal is released, the display on scan
tool MB991958 should be "OFF".
MB991827
AC404789AB
YES : Go to Step 4 <M/T> or Step 5 <A/T>.
TSB Revision
AUTO-CRUISE CONTROL
17-71
Clutch switch <M/T>.
CAUTION
DATA LINK
(Refer to P.17-11).
• Item 78: Clutch switch.
MB991910
• When the clutch pedal is depressed, the display on
• When the clutch pedal is released, the display on
YES : Go to Step 6.
MB991827
AC404789AB
Neutral switch <A/T>.
CAUTION
DATA LINK
(Refer to P.17-11).
• Item 88, Neutral switch.
MB991910
• When selector lever is at the "N" position, the display
MB991824 on scan tool MB991958 should be "ON".
• When selector lever is other than "N" position, the
YES : Go to Step 6.
MB991827
AC404789AB
TSB Revision
AUTO-CRUISE CONTROL

Q: Can auto-cruise control be set?
7.

Q: Can auto-cruise control be set?
INSPECTION PROCEDURE 6: Hunting (Repeated Acceleration and Deceleration) Occurs at the Set
Vehicle Speed.

.
COMMENT
The output shaft speed sensor signal or the throttle LIKELY CAUSES FOR THIS CASE:)
body is suspected. • Malfunction of the vehicle speed sensor <M/T>.
• Malfunction of the output shaft speed sensor
<A/T>.
.
• Malfunction of the throttle body.

DIAGNOSIS
• MB991824: V.C.I.
TSB Revision
AUTO-CRUISE CONTROL
17-73

diagnostic trouble code <M/T>.
CAUTION
DATA LINK
(Refer to P.17-11).
MB991910
Q: Is DTC P0500 set?
YES : Refer to GROUP 13A, MFI Diagnosis −Diagnostic
Trouble Code Procedures −DTC P0500: Vehicle
Speed Sensor Malfunction <M/T>P.13A-794 <2.4L
MB991827
engine> or Refer to GROUP 13B, MFI Diagnosis −
AC404789AB Diagnostic Trouble Code Procedures −DTC P0500:
Vehicle Speed Sensor Malfunction <M/T>P.13B-832
<3.8L engine>. Then go to Step 5.
NO : Go to Step 3.

diagnostic trouble code <A/T>.
CAUTION
DATA LINK
(Refer to P.17-11).
MB991910
Q: Is DTC P1767 set?
YES : Refer to GROUP 23A, A/T Diagnosis −Diagnostic
Trouble Code Procedures −DTC P1767: Output Shaft
Speed Sensor System P.23A-113. Then go to Step 5
.
NO : Go to Step 3.
MB991827
AC404789AB
TSB Revision
AUTO-CRUISE CONTROL

CAUTION
DATA LINK
(Refer to P.17-11).
(3) Check for MFI system diagnostic trouble code (Refer to
MB991910
Q: Is any DTC set?
YES : Diagnose the MFI system. (Refer to GROUP 13A,
MFI Diagnosis −Diagnostic Trouble Code Chart
MB991827 MFI Diagnosis −Diagnostic Trouble Code Chart
AC404789AB
NO : Go to Step 4.
STEP 4. Retest the system

Q: Does hunting occur?
5.
STEP 5. Retest the system

Q: Does hunting occur?
TSB Revision
AUTO-CRUISE CONTROL
17-75
INSPECTION PROCEDURE 7: When "CRUISE" (MAIN) Switch is Turned "ON", "CRUISE" Indicator
Light Inside Combination Meter does not Illuminate. (However, Auto-cruise Control System is
Normal).
Auto-cruise Control Indicator Light Drive Circuit
BATTERY IGNITION SWITCH (IG1)
WHITE
WHITE
RED
JUNCTION
BLOCK
RELAY
BOX
GREEN
WHITE
RHEOSTAT
RED-
JOINT
CONNECTOR (2)
WHITE
GREEN
RED-
COMBINATION
METER
BLACK
BLACK
RED
JOINT
CONNECTOR (3)
BLACK
RED
BLACK
RED
ABS-ECU
OR
ABS/TCL-ECU
BLACK
RED
NOTE
: 2.4L ENGINE
: 3.8L ENGINE ECM <M/T> OR PCM <A/T>
AC407007 AB
TSB Revision
AUTO-CRUISE CONTROL
CONNECTORS: A-02, A-03 CONNECTOR: B-18
A-02 (B)
ECM <M/T>
<2.4L> OR OR
A-03 (B) PCM <A/T>
<3.8L>
B-18 (B)
AIR CLEANER
A-02 HARNESS CONNECTOR:

COMPONENT SIDE
B-18 HARNESS
CONNECTOR:
COMPONENT SIDE
A-03 HARNESS CONNECTOR:

COMPONENT SIDE
AC406859 AB AC407016 AC
CONNECTORS: C-01, C-03, C-04, C-24 CONNECTORS: C-202, C-215

C-01 C-04 JUNCTION BLOCK
(FRONT VIEW)
C-202
C-03
C-215
C-24

C-01 HARNESS C-03 HARNESS COMPONENT SIDE

C-24 MALE SIDE COMPONENT SIDE
C-04 HARNESS CONNECTOR
CONNECTOR:
COMPONENT SIDE
AC406808 AG AC406863 AB
COMMENT
.
CIRCUIT OPERATION
The ECM <M/T> or PCM <A/T> detects "CRUISE" Connector(s), wiring harness in the CAN bus line
(MAIN) switch "ON" signal to illuminate the between the ECM <M/T> or PCM <A/T> and the
"CRUISE" indicator light on the combination meter. combination meter, power supply to the ECM <M/T>
or PCM <A/T>, the combination meter, the ECM
.
<M/T> or PCM <A/T> may be defective.
.
TSB Revision
AUTO-CRUISE CONTROL
17-77
TROUBLESHOOTING HINTS
• Malfunction of the combination meter.
• Damaged harness or connector.
DIAGNOSIS
• MB991824: V.C.I.
STEP 1. Using scan tool MB991958, diagnose the CAN bus

line.
CAUTION
DATA LINK
(Refer to P.17-11).
(3) Diagnose the CAN bus line. (Refer to P.17-11).
MB991910
Q: Is the check result satisfactory?
MB991824
YES : Go to Step 2
NO : Repair the CAN bus lines. (Refer to GROUP 54C,
Diagnosis −Can Bus Diagnostic Chart P.54C-14).
Then go to Step 4.
MB991827
AC404789AB
TSB Revision
AUTO-CRUISE CONTROL
STEP 2. Using scan tool MB991958, read the MFI

CAUTION
DATA LINK
(Refer to P.17-11).
(3) Check for MFI system diagnostic trouble code (Refer to
MB991910
Q: Is DTC U1108 set?
YES : Refer to GROUP 13A, MFI Diagnosis −Diagnostic
Trouble Code Procedures −DTC U1108: Combination
Meter-ECU CAN Communication Time Out
MB991827 P.13A-995 <2.4L engine> or Refer to GROUP 13B,
AC404789AB MFI Diagnosis −Diagnostic Trouble Code Procedures
−DTC U1108: Combination Meter-ECU CAN
Communication Time Out P.13B-1070 <3.8L engine>.
Then go to Step 4.
NO : Go to Step 3.

Q: Does the "CRUISE" indicator light illuminate when the
"CRUISE" (MAIN) switch is turned "ON"?
4.

Q: Does the "CRUISE" indicator light illuminate when the
"CRUISE" (MAIN) switch is turned "ON"?
TSB Revision
AUTO-CRUISE CONTROL
17-79
DATA LIST REFERENCE TABLE
M1172002400482
CAUTION
• Driving tests always need two persons: one driver and one observer.
• When shifting the selector lever to "D" range apply the brakes should be applied so that the vehi-
cle does not move forward <A/T>.
NOTE: *:After the inspection is completed, disconnect the throttle position sensor connector, and then delete
the diagnostic trouble code using scan tool MB991958. (Refer to P.17-11).
MUT-III ITEM INSPECTION ITEM INSPECTION REQUIREMENT NORMAL

SCAN TOOL NO. CONDITION
DISPLAY
APS (main) 11 Accelerator pedal Ignition Accelerator pedal: Released 735 −1,335 mV
position sensor (main) switch: Accelerator pedal: Gradually Increases in
"ON" depressed response to the
pedal depression
stroke
Accelerator pedal: Fully 4,000 mV or more
depressed
Brake light 74 Stoplight switch Brake pedal: Depressed ON
switch Brake pedal: Released OFF
Cancel code 57 Cancel code Ignition switch: "ON" The cancel code,
which set when the
auto-cruise control
system was
cancelled at the
last time.
Cancel switch 75 Auto-cruise CANCEL "CANCEL" switch: ON ON
control "CANCEL" switch: OFF OFF
switch
Clutch switch 78 Clutch pedal position Clutch pedal: Depressed ON
switch <M/T> Clutch pedal: Released OFF
Cruise switch 81 Auto-cruise control Auto-cruise control system: active ON
system operation Auto-cruise control system: Inactive OFF
Main switch 86 Auto-cruise CRUISE "CRUISE" (MAIN) switch: "ON" ON
control (MAIN) "CRUISE" (MAIN) switch: "OFF" OFF
switch
Neutral 88 Transmission range Transmission range switch: "N" ON
switch switch <A/T> position
Transmission range switch: Other than OFF
above
Normally 89 Stoplight switch (brake Brake pedal: Depressed ON
closed brake switch) Brake pedal: Released OFF
switch
Resume 91 Auto-cruise ACC/RES "ACC/RES" switch: ON ON
switch control "ACC/RES" switch: OFF OFF
switch
TSB Revision
AUTO-CRUISE CONTROL
MUT-III ITEM INSPECTION ITEM INSPECTION REQUIREMENT NORMAL

SCAN TOOL NO. CONDITION
DISPLAY
Set switch 92 Auto-cruise COAST/S "COAST/SET" switch: ON ON
control ET "COAST/SET" switch: OFF OFF
switch
TPS (main) 13 Throttle position sensor • Remove the intake air Fully close 300 − 700 mV
(main)* hose at the throttle the throttle
body. valve with
• Disconnect the throttle your finger
position sensor Fully open 4,000 mV or more
connector, and then the throttle
connect terminals 3, 4, valve with
5 and 6 with the use of your finger
the special tool:
MB991658 (Test
harness).
• Ignition switch: "ON"
No load 520 − 620 mV
A/C switch: "OFF" to "ON" Voltage rises
Selector lever: "N" to "D" Voltage rises
Vehicle speed 4 Vehicle speed signal Road test the vehicle The speedometer
sensor and scan tool
MB991958 display
the same value.
TSB Revision
AUTO-CRUISE CONTROL
17-81
ECM <M/T> OR PCM <A/T> TERMINAL VOLTAGE REFERENCE CHART FOR
AUTO-CRUISE CONTROL SYSTEM OPERATION
M1172006000044
1. Disconnect the ECM <M/T> or PCM <A/T> 2. Measure the voltages between the check
connectors, and connect special tool MB991923 connector terminals of special tool MB991923 and
(Power plant ECU check harness) in between. ground terminals 63 or 76.
SPECIAL TOOL-POWER PLANT ECU CHECK HARNESS (MB991923) CONNECTOR: COMPONENT SIDE
33-PIN 23-PIN 33-PIN 23-PIN 18-PIN

CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR
(PCM CONNECTOR WITH RED TAPE (PCM CONNECTOR WITHOUT RED TAPE (PCM CONNECTOR
B-23) (PCM CONNECTOR B-21) (PCM CONNECTOR B-19)
B-22) B-20)
127 126 125 124 123 122 121 95 94 93 92 91 57 56 55 54 53 52 51 25 24 23 22 21 4 3 2 1

133 132 131 130 129 128 99 98 97 96 6362 61 60 59 58 29 28 27 26 7 6 5
140 139 138 137 136 135 134 104 103 102 101 100 70 69 68 67 66 65 64 34 33 32 31 30 11 10 8 9
146 145 144 143 142 141 108 107 106 105 76 75 74 73 72 71 38 37 36 35 14 13 12
153 152 151 150 149 148 147 113 112 111 110 109 83 82 81 80 79 78 77 43 42 41 40 39 18 17 16 15
AC209259AE
TERMINAL CHECK ITEM CHECK CONDITION NORMAL

NO. CONDITION
9 Stoplight switch Ignition Depress the brake pedal. Battery positive
switch: voltage
"ON" Release the brake pedal. 1V or less
12 Auto-cruise control Ignition All switches: OFF 4.7 − 5.0 V
switch power supply switch: "CRUISE" (MAIN) switch: "ON" 0 − 0.3 V
"ON"
"COAST/SET" switch: ON 2.0 − 2.8 V
"ACC/RES" switch: ON 3.3 − 4.1 V
"CANCEL" switch: ON 0.8 − 1.5 V
16 Clutch pedal position Ignition Depress the clutch pedal. 4.9 − 5.1 V
switch <M/T> switch: Release the clutch pedal. 1V or less
"ON"
21 Sensor supplied Ignition switch: "ON" 4.9 − 5.1 V
voltage
26 Accelerator pedal Ignition Release the accelerator pedal 0.735 − 1.335 V
position sensor switch: Depress the accelerator pedal. 4.0 V or more
(main) "ON"
27 Accelerator pedal Ignition Release the accelerator pedal 0.435 − 1.035 V
position sensor (sub) switch: Depress the accelerator pedal. 3.7 V or more
"ON"
30 Power supply voltage Ignition switch: "ON" 4.9 − 5.1 V
applied to accelerator
pedal position sensor
(main)
33 Stoplight switch Ignition Depress the brake pedal. Battery positive
(brake switch) switch: voltage
"ON" Release the brake pedal. 1V or less
TSB Revision
AUTO-CRUISE CONTROL
TERMINAL CHECK ITEM CHECK CONDITION NORMAL

NO. CONDITION
77 Transmission range Ignition Transmission range switch: "N" Battery positive
switch: "N" <A/T> switch: position voltage
"ON" Transmission range switch: Other 1V or less
than above
94 Power supply voltage Ignition switch: "ON" 4.9 − 5.1 V
applied to throttle
position sensor
98 Throttle position • Remove the intake air Fully close the 2.2 − 2.8 V
sensor (sub) hose at the throttle body throttle valve
• Disconnect the throttle with your finger
position sensor, and then Fully open the 4.0 V or more
connect terminals 3, 4, 5 throttle valve
and 6 with the use of the with your finger
special tool: MB991658
(Test harness).
99 Throttle position • Remove the intake air Fully close the 0.3 − 0.7 V
sensor (main) hose at the throttle body throttle valve
• Disconnect the throttle with your finger
position sensor, and then Fully open the 4.0 V or more
connect terminals 3, 4, 5 throttle valve
and 6 with the use of the with your finger
special tool: MB991658.
141 Throttle actuator • Ignition switch: "ON" Decreases slightly
control motor (−) • Accelerator pedal: fully closed to fully (approx. 2 V) from
opened battery voltage.
147 Throttle actuator • Ignition switch: "ON" Decreases slightly
control motor (+) • Accelerator pedal: fully opened to fully (approx. 2 V) from
closed battery voltage.
TSB Revision
AUTO-CRUISE CONTROL
17-83
SPECIAL TOOLS
M1172000600543

NAME
MB991958 MB991824-KIT Checking data list
A
A: MB991824 NOTE: G: MB991826 CAUTION
B: MB991827 MUT-III trigger harness is For vehicles with CAN
C: MB991910 not necessary when communication, use
D: MB991911 pushing V.C.I. ENTER MUT-III main harness A
MB991824
E: MB991914 key. to send simulated
B F: MB991825 vehicle speed. If you
G: MB991826 connect MUT-III main
MUT-III sub assembly harness B or C instead,
A: Vehicle the CAN
communication communication does
MB991827
interface (V.C.I.) not function correctly.
C
B: MUT-III USB cable
C: MUT-III main harness
A (Vehicles with CAN
communication
MB991910 system)
D D: MUT-III main harness
B (Vehicles without
DO NOT USE CAN communication
system)
E: MUT-III main harness
MB991911
C (for Daimler Chrysler
E models only)
F: MUT-III measurement
DO NOT USE adapter
G: MUT-III trigger
MB991914 harness
F
MB991825
MB991826
MB991958
TSB Revision
AUTO-CRUISE CONTROL

NAME
MB991223 General service tools Checking the continuity
A
A: MB991219 and measuring the
B: MB991220 voltage at the harness
C: MB991221 connector
D: MB991222
B Harness set
A: Test harness
B: LED harness
C: LED harness adaptor
C
D: Probe
D
DO NOT USE
MB991223 AZ
MB992006 General service tool Continuity check and

Extra fine probe voltage measurement at
harness wire or connector
for loose, corroded or
damaged terminals, or
MB992006
terminals pushed back in
the connector.
MB991923 − Measuring the terminal
Power plant ECU check voltage at the ECM
harness <M/T> or PCM <A/T>
MB991923
MB991658 Tool not available Checking throttle position

Test harness sensor
MB991658
TSB Revision
AUTO-CRUISE CONTROL
17-85
ON-VEHICLE SERVICE
AUTO-CRUISE CONTROL SWITCH CHECK

M1172001200140
AUTO-CRUISE CONTROL MAIN SWITCH CHECK

2. Check that the "CRUISE" indicator light within the
combination meter illuminates when the "CRUISE" (MAIN)
switch is switched "ON".
"CRUISE"
(MAIN)
SWITCH:
"ON"
AUTO-CRUISE
CONTROL SWITCH
AC406686
"CRUISE" INDICATOR LIGHT
AC406684
AC406782 AB
AUTO-CRUISE CONTROL SETTING

1. Switch "ON" the "CRUISE" (MAIN) switch.
2. Drive at the desired speed, above approximately 40 km/h
(25 mph).
3. Push the auto-cruise control switch in the direction of the
arrow.
4. Check to be sure that when the switch is released the speed
is the constant speed.
NOTE: If the vehicle speed decreases to approximately 15
km/h (9 mph) below the set speed because of climbing a hill
for example, it is normal for the auto-cruise control to be
cancelled.
ACX01172 AD
TSB Revision
AUTO-CRUISE CONTROL
SPEED-INCREASE SETTING
2. Set to the desired speed, above approximately 40 km/h (25
mph).
arrow.
4. Check to be sure that acceleration continues while the
switch is held, and that the speed at the time it was released
becomes the constant driving speed.
NOTE: Acceleration can be continued even if the vehicle
speed has passed the high-speed limit [approximately 200
km/h (124 mph)]. But the constant driving speed when the
auto-cruise control switch is released will be recorded as the
ACX01172 AE
high-speed limit.
SPEED-REDUCTION SETTING
mph).
arrow.
4. Check to be sure that deceleration continues while the
switch is pressed, and that the speed at the time it was
released becomes the constant driving speed.
NOTE: When the vehicle speed reaches the low limit
[approximately 40 km/h (25 mph)] during deceleration, the
auto-cruise control will be cancelled.
ACX01172 AD
RETURN TO THE SET SPEED BEFORE

CANCELLATION AND AUTO-CRUISE CONTROL
CANCELLATION
mph).
3. When any of the following operations are performed while at
constant speed during auto-cruise control, check if normal
driving is resumed and deceleration occurs.
(1) The auto-cruise control switch is pulled in the direction of
the arrow.
(2) The brake pedal is depressed.
(3) The selector lever is moved to the "N" range.
4. At a vehicle speed of 40 km/h (25 mph) or higher, check if
when the "ACC/RES" switch is switched ON, the vehicle
speed returns to the speed before auto-cruise control driving
was cancelled, and constant speed driving occurs.
ACX01172 AG
TSB Revision
AUTO-CRUISE CONTROL
17-87
5. When the "CRUISE" (MAIN) switch is turned to the "OFF"
while driving at constant speed, check if normal driving is
resumed and deceleration occurs.
AUTO-CRUISE CONTROL SYSTEM COMPONENT

CHECK
M1172001700510
AUTO-CRUISE CONTROL SWITCH CHECK

1. Remove the steering wheel assembly. (Refer to GROUP 37,
Steering Wheel P.37-27).
2. Measure the resistance between terminal 2 and terminal 3
when each of the "COAST/SET", "ACC/RES", "CANCEL"
AUTO-CRUISE
CONTROL and "CRUISE" (MAIN) switches is pressed. If values
SWITCH measured at the time each switch is pressed correspond to
those in the table below, the resistance values are correct.
SWITCH POSITION SPECIFIED CONDITION
5 4 3 2 1
"CRUISE" (MAIN) switch Open circuit
"OFF"
AC406783
"CRUISE" (MAIN) switch "ON" Less than 2 ohms
2
"CANCEL" switch ON Approximately 100 Ω
"ACC/RES" switch ON Approximately 887 Ω
"COAST/SET" switch ON Approximately 300 Ω
MAIN RES SET CAN

OFF OFF OFF OFF
ON ON ON ON
3 AC406784 AB
STOPLIGHT SWITCH
1. Disconnect the connector.
2. Check for continuity between the terminals of the switch.
MEASUREMENT TERMINAL SPECIFIED
CONDITION CONNECTOR CONDITION
OF TESTER
When brake pedal 1 − 2 (for stoplight Less than 2 ohms
is depressed. switch)
3 − 4 (for normally Open circuit
closed brake
ACX01180 AB
switch)
When brake pedal 1 − 2 (for stoplight Open circuit
is not depressed. switch)
3 − 4 (for normally Less than 2 ohms
closed brake
switch)
TSB Revision
AUTO-CRUISE CONTROL
CLUTCH PEDAL POSITION SWITCH <M/T>

1. Disconnect the connector.
2. Check for continuity between the terminals of the switch.
MEASUREMENT TERMINAL SPECIFIED
CONDITION CONNECTOR CONDITION
OF TESTER
When clutch pedal is 1 − 2 Less than 2 ohms
depressed.
When clutch pedal is 1 − 2 Open circuit
not depressed.
ACX01180 AB
TRANSMISSION RANGE SWITCH ("N" POSITION)

<A/T>
Refer to GROUP 23A, On-vehicle Service −Essential Service
P.23A-387.
THROTTLE POSITION SENSOR

Refer to GROUP 13A, On-vehicle Service −Throttle Actuator
Control Motor Check P.13A-1207 <2.4L engine>.
Refer to GROUP 13B, On-vehicle Service −Throttle Actuator
Control Motor Check P.13B-1288 <3.8L engine>.
TSB Revision
AUTO-CRUISE CONTROL
17-89
AUTO-CRUISE CONTROL
M1172001400489
CAUTION
Do not replace the ECM <M/T> or PCM <A/T> and the ETACS-ECU simultaneously. Always replace
either one of the ECUs first, and register the encrypted code (Refer to GROUP 54A, Immobilizer Sys-
tem −Encrypted Code Registration Criteria Table P.54A-13). Then, replace the other ECU.
AC406785
3
7
2
AC406683
AC406786 AB
CONTROL SWITCH REMOVAL SENSOR REMOVAL STEPS

STEPS 3. TRANSMISSION RANGE SWITCH
1. STEERING WHEEL ASSEMBLY <A/T> (REFER TO GROUP 23B,
(BUILT-IN AUTO-CRUISE CONTROL TRANSAXLE P.23B-8 <4A/T> OR
SWITCH) (REFER TO GROUP 37, REFER TO GROUP 23C,
STEERING WHEEL P.37-27) TRANSAXLE P.23C-8) <5A/T>
CONTROL UNIT REMOVAL 4. THROTTLE BODY (BUILT-IN
2. ECM <M/T> OR PCM <A/T> [REFER THROTTLE POSITION SENSOR
TO GROUP 13A, ENGINE AND THROTTLE ACTUATOR
CONTROL MODULE (ECM) <M/T> CONTROL MOTOR) (REFER TO
AND POWERTRAIN CONTROL GROUP 13A, THROTTLE BODY
MODULE (PCM) <A/T>P.13A-1214] P.13A-1212) <2.4L ENGINE> OR
<2.4L ENGINE> OR [REFER TO (REFER TO GROUP 13B,
GROUP 13B, ENGINE CONTROL THROTTLE BODY P.13B-1293)
MODULE (ECM) <M/T> AND <3.8L ENGINE>
POWERTRAIN CONTROL MODULE 5. ACCELERATOR PEDAL (BUILT-IN
(PCM) <A/T>P.13B-1295] <3.8L ACCELERATOR PEDAL POSITION
ENGINE> SENSOR) (REFER TO P.17-9)
TSB Revision
EMISSION CONTROL
SENSOR REMOVAL STEPS

6. STOPLIGHT SWITCH (REFER TO
GROUP 35A, BRAKE PEDAL
P.35A-25)
7. CLUTCH PEDAL POSITION
SWITCH <M/T> (REFER TO GROUP
21, CLUTCH PEDAL P.21A-12)
EMISSION CONTROL
GENERAL DESCRIPTION
M1173000100701
The emission control system consists of the fol- • Evaporative emission system
lowing subsystems: • Exhaust emission control system
• Positive crankcase ventilation system
DIAGNOSIS
M1173000700190
SYMPTOM PROBABLE CAUSE REMEDY

Engine will not start or hard Vacuum hose disconnected or damaged Repair or replace
to start The EGR valve (Stepper Motor) is not Repair or replace
closed.
Malfunction of the evaporative emission Repair or replace
purge solenoid
Rough idle or engine stalls The EGR valve (Stepper Motor) is not Repair or replace
closed.
Vacuum hose disconnected or damaged. Repair or replace
Malfunction of the positive crankcase Replace
ventilation valve
Malfunction of the purge control system Check the system; If there is a
problem, check its component
parts.
Engine hesitates or poor Malfunction of the exhaust gas Check the system; If there is a
acceleration recirculation system problem, check its component
parts.
Excessive oil consumption Positive crankcase ventilation line Check positive crankcase
clogged ventilation system
Poor fuel mileage Malfunction of the exhaust gas Check the system; If there is a
recirculation system problem, check its component
parts.
TSB Revision
EMISSION CONTROL
17-91
SPECIAL TOOLS
M1173000600405

NAME
MB995061 MLR6890A Inspection of purge
Purge flow indicator Part of MIT280220 control system
MB991658 Tool not available Inspection of EGR valve

Test harness set (Stepper Motor)
MB991658
MD998770 MD998770-01 or General Removal/installation of

Oxygen sensor wrench service tool heated oxygen sensor
TSB Revision
EMISSION CONTROL
VACUUM HOSES
VACUUM HOSE ROUTING
M1173000900763
<2.4L ENGINE>
EVAPORATIVE
EMISSION
CANISTER
EVAPORATIVE EMISSION
VENTILATION SOLENOID
PURGE SOLENOID
THROTTLE
INTAKE MANIFOLD BODY
PRENUM
FRONT B: BLACK
AK404090 AB
TSB Revision
EMISSION CONTROL
17-93
<3.8L ENGINE>
VENTILATION SOLENOID
EVAPORATIVE
EMISSION
CANISTER
*2
CHAMBER
INTAKE MANIFOLD PLENUM B
*1
EVAPORATIVE
EMISSION
PURGE SOLENOID
FRONT
B : BLACK
*1:WHITE PAINT MARK
*2:YELLOW PAINT MARK
AK404091 AB
TSB Revision
EMISSION CONTROL
VACUUM CIRCUIT DIAGRAM

M1173007100564
<2.4L ENGINE>
INTAKE MANIFOLD THROTTLE BODY
TO
COMBUSTION FROM
CHAMBER AIR CLEANER
PURGE SOLENOID
B (ON: OPEN)
B FUEL
TANK
CANISTER
VENTILATION SOLENOID B: BLACK
(ON: CLOSED)
AK404092 AB
TSB Revision
EMISSION CONTROL
17-95
<3.8L ENGINE>
TO
COMBUSTION FROM
CHAMBER AIR CLEANER
PURGE SOLENOID
B (ON: OPEN)
CHAMBER
*1
*2
B FUEL
TANK
CANISTER
EVAPORATIVE EMISSION B: BLACK
VENTILATION SOLENOID *1:WHITE PAINT MARK
(ON: CLOSED) *2:YELLOW PAINT MARK
AK404093 AB
VACUUM HOSE INSTALLATION

M1173007200237
1. When connecting the vacuum hoses, they should be
securely inserted onto the nipples.
2. Connect the hoses correctly, using the VACUUM HOSE
ROUTING diagram as a guide.
VACUUM HOSE CHECK

M1173007300308
1. Using the VACUUM HOSE ROUTING diagram as a guide,
check that the vacuum hoses are correctly connected.
2. Check the connection of the vacuum hoses, (removed,
loose, etc.) and confirm that there are no sharp bends or
damage.
TSB Revision
EMISSION CONTROL
POSITIVE CRANKCASE VENTILATION SYSTEM

GENERAL DESCRIPTION (POSITIVE CRANKCASE VENTILATION SYSTEM)
M1173005000679
The positive crankcase ventilation (PCV) system pre- The PCV valve is designed to lift the plunger accord-
vents the escape of blow-by gases from inside the ing to the intake manifold vacuum so as to regulate
crankcase into the atmosphere. the flow of blow-by gas properly.
Fresh air is sent from the air cleaner into the crank- In other words, the blow-by gas flow is regulated dur-
case through the breather hose to be mixed with the ing low load engine operation to maintain engine sta-
blow-by gas inside the crankcase. bility, while the flow is increased during high load
The blow-by gas inside the crankcase is drawn into operation to improve the ventilation performance.
the intake manifold through the PCV valve.
SYSTEM DIAGRAM
<2.4L ENGINE>
VENTILATION HOSE
POSITIVE CRANKCASE
VENTILATION VALVE
BREATHER HOSE
AK300553 AC
TSB Revision
EMISSION CONTROL
17-97
<3.8L ENGINE>
VENTILATION HOSE
BREATHER HOSE
POSITIVE CRANKCASE
VENTILATION VALVE
AK303639 AB
COMPONENT LOCATION
M1173007400413
POSITIVE CRANKCASE VENTILATION VALVE POSITIVE CRANK CASE VENTILATION VALVE

<2.4L ENGINE> <3.8L ENGINE>
AK301395AB AK404094AB
POSITIVE CRANKCASE VENTILATION SYSTEM

CHECK
M1173001100436
1. Remove the positive crankcase ventilation (PCV) valve from
the rocker cover, then reconnect the PCV valve to the
vacuum supply hose.
POSITIVE CRANKCASE 2. With the engine idling, put your finger on the open end of the
VENTILATION VALVE PCV valve, and check for negative pressure (vacuum).
NOTE: At this time, the plunger in the PCV valve should
move back and forth as the open end is covered and uncov-
ered.
3. If negative pressure is not felt, clean or replace the PCV
valve. Inspect the vacuum supply hose and vacuum supply
hose port for restriction or plugged condition.
AK203692 AC
TSB Revision
EMISSION CONTROL
POSITIVE CRANKCASE VENTILATION VALVE

CHECK
M1173001200392
1. Hold the positive crankcase ventilation (PCV) valve with the
5 – 10 mm
vacuum side down. Insert a thin rod, and using light
(0.2 – 0.3 in)
THIN ROD pressure, depress the end of the PCV valve spring by 5 −10
(VERY SMOOTH) mm (0.2 − 0.3 inch). Release pressure on the rod to see if
the PCV valve spring will lift the rod to its original position.
POSITIVE
CRANKCASE 2. If the rod returns quickly to its original position, the PCV
VENTILATION valve is OK. If the stick does not return quickly, clean or
VALVE
replace the PCV valve.
VACUUM SIDE
AK301831 AB
EVAPORATIVE EMISSION CONTROL SYSTEM

GENERAL DESCRIPTION (EVAPORATIVE EMISSION SYSTEM)
M1173005100825
The evaporative emission (EVAP) system prevents An EVAP ventilation solenoid is provided between
fuel vapors generated in the fuel tank from escaping the EVAP canister and atmosphere to monitor for
into the atmosphere. OBD-II EVAP leaks. This solenoid is normally OFF.
Fuel vapors from the fuel tank flow through the vapor However, it turns ON when monitoring the OBD-II
pipe/hose to be stored temporarily in the EVAP can- EVAP leaks and shuts off the atmosphere flow to the
ister. EVAP canister. Then the fuel tank differential pres-
When the vehicle is in operation, fuel vapors stored sure sensor monitors the fuel vapor pressure to
in the EVAP canister flow through the EVAP purge detect OBD-II EVAP leaks. The fuel overflow limiter
solenoid, purge port and intake manifold plenum to valve and the leveling valve prevent fuel from being
the combustion chamber. overfilled. The fuel overflow limiter valve and the lev-
When the engine coolant temperature is low or when eling valve prevents fuel leaks if the vehicle is rolled
the intake air quantity is small (when the engine is at over in an accident.
idle, for example), the engine control module (ECM) The EVAP ventilation valve releases the air from the
or powertrain control module (PCM) brings the EVAP fuel tank through the EVAP canister into the atmo-
purge solenoid into the OFF state to shut off the fuel sphere when the fuel tank pressure increases due to
vapor flow to the intake manifold plenum. This refueling, etc. The EVAP ventilation valve and the air
ensures driveability when the engine is cold or run- filter supply the atmospheric air to the EVAP canister
ning under low load and also stabilizes the emission when the fuel tank pressure decreases.
level.
TSB Revision
EMISSION CONTROL
17-99
SYSTEM DIAGRAM
<2.4L ENGINE>
EVAPORATIVE
EMISSION
PURGE FUEL TANK DIFFERENTIAL
SOLENOID PRESSURE SENSOR
ON: OPEN
LIQUID SEPARATOR
FUEL OVERFLOW
LIMITER VALVE
EVAPORATIVE
EMISSION
ECM<M/T> CANISTER
BAROMETRIC PRESSURE PCM<A/T>
SENSOR FUEL
INTAKE AIR TEMPERATURE TANK
SENSOR
FUEL CUT
ENGINE COOLANT LEVELING VALVE OFF VALVE
TEMPERATURE SENSOR MFI RELAY
EVAPORATIVE EMISION
VENTILATION VALVE
MASS AIRFLOW SENSOR
VENTILATION SOLENOID AIR FILTER
ON: CLOSED
AK500786 AB
TSB Revision
EMISSION CONTROL
<3.8L ENGINE>
EVAPORATIVE
EMISSION
PURGE FUEL TANK DIFFERENTIAL
SOLENOID PRESSURE SENSOR
ON: OPEN LIQUID
SEPARATOR
FUEL PRESSURE
REGULATOR FUEL
OVERFLOW
LIMITER
ECM <M/T> VALVE
BAROMETRIC PRESSURE PCM <A/T>
SENSOR
INTAKE AIR TEMPERATURE FUEL FUEL CUT
SENSOR TANK OFF VALVE
ENGINE COOLANT MFI LEVELING
RELAY FUEL EVAPORATIVE VALVE
TEMPERATURE SENSOR EMISSION
PUMP
CANISTER
MASS AIRFLOW SENSOR
EVAPORATIVE
EMISSION
EVAPORATIVE VENTILATION VALVE
EMISSION
VENTILATION SOLENOID AIR FILTER
ON: CLOSED
AK500787AB
COMPONENT LOCATION
M1173007500421
EVAPORATIVE EMISSION PURGE SOLENOID EVAPORATIVE EMISSION VENTILATION

<2.4L ENGINE> SOLENOID
EVAPORATIVE
EMISSION CANISTER
AK404081AB AK404083AB
EVAPORATIVE EMISSION PURGE SOLENOID

<3.8L ENGINE>
AK404082AB
TSB Revision
EMISSION CONTROL
17-101
PURGE CONTROL SYSTEM CHECK (PURGE FLOW CHECK)
M1173001400749
TO
COMBUSTION FROM
CHAMBER AIR CLEANER
OFF
PURGE SOLENOID
(ON: OPENED)
ON
PURGE
PURGE HOSE FLOW
INDICATOR
(MB995061)
CANISTER
AK500788 AB
Required Special Tool:

MB995061: Purge Flow Indicator
1. Disconnect the purge hose from the evaporative emission
(EVAP) purge solenoid, and connect special tool MB995061
between the EVAP purge solenoid and the purge hose.
2. Before inspection, set the vehicle in the following conditions:
• Engine coolant temperature: 80 − 95° C (176 − 203° F)
• Lights, electric cooling fan and accessories: OFF
• Transaxle: Neutral (P range on vehicles with A/T)
NOTE: Vehicles for Canada, the headlight, taillight, etc.
remain lit even when the lighting switch is in "OFF" position
but this is no problem for checks.
3. Run the engine at idle for more than four minutes.
4. Check the purge flow volume when engine is revved
suddenly several times.
Standard value: Momentarily 20 cm3/s (2.5 SCFH) or
more.
5. If the purge flow volume is less than the standard value,
check it again with the vacuum hose disconnected from the
EVAP canister. If the purge flow volume is less than the
standard value, check the vacuum port and the vacuum
hose for clogging. Also check the EVAP purge solenoid. If
the purge flow volume is at the standard value, replace the
EVAP canister.
TSB Revision
EMISSION CONTROL
EVAPORATIVE EMISSION PURGE SOLENOID

CHECK
M1173001700450
1. Disconnect the vacuum hose (black, black with red paint
mark) from the evaporative emission (EVAP) purge
solenoid.
NOTE: When disconnecting the vacuum hose, always place
an identification mark so that it can be reconnected at its
original position.
2. Disconnect the harness connector.
3. Connect a hand vacuum pump to nipple (A) of the EVAP
A
purge solenoid (refer to the illustration at left).
B 4. As described in the chart below, check airtightness by
applying a vacuum with voltage applied directly from the
battery to the EVAP purge solenoid valve and without
applying voltage.
BATTERY POSITIVE NORMAL CONDITION
VOLTAGE
AK402742AD Applied Vacuum leaks
Not applied Vacuum maintained
5. Measure the resistance between the terminals of the EVAP

purge solenoid.
Standard value: 22 − 26 ohms [at 20° C (68° F)]
6. Replace the solenoid if resistance is out of specification.
AK402743
MASS AIRFLOW SENSOR CHECK

M1173050400138
<2.4L ENGINE>
To inspect these parts, refer to GROUP 13A, Multiport Fuel
Injection (MFI) <2.4L Engine> −Multiport Fuel Injection (MFI)
Diagnosis − Diagnostic Trouble Code Chart P.13A-41.
<3.8L ENGINE>
To inspect these parts, refer to GROUP 13B, Multiport Fuel
Diagnosis − Diagnostic Trouble Code Chart P.13B-43.
BAROMETRIC PRESSURE SENSOR CHECK

M1173008000355
<2.4L ENGINE>
To inspect the sensor, refer to GROUP 13A, Multiport Fuel
Diagnosis − Diagnostic Trouble Code Chart P.13A-41.
TSB Revision
EMISSION CONTROL
17-103
<3.8L ENGINE>
To inspect the sensor, refer to GROUP 13B, Multiport Fuel
Diagnosis − Diagnostic Trouble Code Chart P.13B-43.
ENGINE COOLANT TEMPERATURE SENSOR

CHECK
M1173008100697
<2.4L ENGINE>
Diagnosis −Diagnostic Trouble Code Chart P.13A-41.
<3.8L ENGINE>
Diagnosis −Diagnostic Trouble Code Chart P.13B-43.
INTAKE AIR TEMPERATURE SENSOR CHECK

M1173008200359
<2.4L ENGINE>
<3.8L ENGINE>
FUEL TANK DIFFERENTIAL PRESSURE SENSOR

CHECK
M1173007700298
To inspect the sensor, refer to GROUP 13C, Fuel Supply −Fuel
Tank −Fuel Tank Inspection −Fuel Tank Differential Pressure
Sensor Check P.13C-15.

SOLENOID CHECK
M1173007800262
Refer to Emission Control −Evaporative Emission Canister and
Fuel Tank Pressure Relief Valve −Inspection −Evaporative
Emission Ventilation Solenoid Check P.17-111.
TSB Revision
EMISSION CONTROL
EXHAUST GAS RECIRCULATION (EGR) SYSTEM

GENERAL DESCRIPTION (EXHAUST GAS RECIRCULATION SYSTEM)
M1173005200662
The exhaust gas recirculation system (EGR) lowers OPERATION
the nitrogen oxides (NOx) emission level. When the When the engine coolant temperature is low, when
air/fuel mixture combustion temperature is high, a the engine is at idle or when a wide open throttle
large quantity of NOx is generated in the combustion operation is performed, the EGR valve (Stepper
chamber. Therefore, this system recirculates part of Motor) is kept closed, achieving no EGR. After warm-
exhaust gas from the exhaust port of the cylinder ing up the engine, the EGR valve (Stepper Motor)
head to the combustion chamber through the intake can be opened by the engine control module (ECM)
manifold to decrease the air/fuel mixture combustion or powertrain control module (PCM).
temperature, resulting in reduction of NOx. The EGR The ECM or PCM monitors the EGR system and illu-
flow rate is controlled by the EGR valve (Stepper minates the Malfunction Indicator Lamp (SERVICE
Motor) for driveability quality. ENGINE SOON or Check Engine Lamp) to indicate
that there is a malfunction.
SYSTEM DIAGRAM
<2.4L ENGINE>
ECM<M/T>
EGR VALVE PCM<A/T>
(STEPPER MOTOR)
MFI RELAY MASS AIRFLOW SENSOR
ENGINE COOLANT
TEMPERATURE SENSOR
BATTERY CRANKSHAFT POSITION
SENSOR
AK300557 AC
TSB Revision
EMISSION CONTROL
17-105
<3.8L ENGINE>
EGR VALVE
(STEPPER MOTOR)
ECM <M/T>
PCM <A/T>
MASS AIRFLOW
MFI RELAY SENSOR
ENGINE COOLANT
TEMPERATURE SENSOR
BATTERY
CRANKSHAFT POSITION
SENSOR
AK203696 AD
COMPONENT LOCATION
M1173007600398
EGR VALVE <2.4L ENGINE> EGR VALVE <3.8L ENGINE>
BRAKE
BOOSTER
AK404084AB AK404085AB
EGR VALVE (STEPPER MOTOR) CHECK

M1173050200286
Required Special Tool:
MB991658: Test Harness Set
.
Checking the Operation Sound

1. Check that the operation sound of the stepper motor can be
heard from the EGR valve when the ignition switch is turned
ON (without starting the engine).
2. If the operation sound cannot be heard, inspect the drive
circuit of the stepper motor.
NOTE: If the operation sound is not heard, and the circuit is
normal, either the stepper motor or the ECM or PCM may have
failed.
.
TSB Revision
EMISSION CONTROL
Checking the Coil Resistance

1. Remove the EGR valve.
2. Measure the resistance between terminal No. 2 and either
terminal No. 1 or terminal No. 3 of the connector at the EGR
valve.
Standard value: 20 − 24 Ω [at 20° C (68° F)]
1 2 3
4 5 6 3. If the resistance is not within the standard, replace the EGR
valve.
1 2 3
4 5 6 4. Measure the resistance between terminal No. 5 and either
AK100014
terminal No. 6 or terminal No. 4 of the connector at the EGR
valve.
5. If the resistance is not within the standard, replace the EGR
valve.
.
Operation Check
1. Remove the EGR valve.
2. Connect special tool MB991658 to the EGR valve.
1 2 3
4 5 6
EGR VALVE
AK202365AC
3. Connect the battery positive (+) terminal to terminal No. 2.

CAUTION
Connecting battery voltage to the EGR valve for a long
time could damage the coil.
4. Connect terminals 1 and 3 to the negative (-) terminal of the
battery, in order to test whether the stepper motor vibrates
(with a slight shudder), indicating that the stepper motor is
BATTERY
operating.
MB991568
5. Connect the battery positive (+) terminal to terminal No. 5.
AK202366 AC
CAUTION
Connecting battery voltage to the EGR valve for a long
time could damage the coil.
6. Connect terminals 4 and 6 to the negative (-) terminal of the
battery, in order to test whether the stepper motor vibrates
(with a slight shudder), indicating that the stepper motor is
operating.
7. If vibrations can be felt as a result of the test, the stepper
motor is determined to be normal.
TSB Revision
EMISSION CONTROL
17-107
EGR VALVE (STEPPER MOTOR) CLEANING
M1173050300045
NOTE: DO not use solvents or other cleaning agents, which will
enter the motor and cause a malfunction.
Remove the EGR valve and make sure that it is not stuck and
does not have any carbon deposits. If there are any carbon
deposits, use a wire brush to clean it.
MASS AIRFLOW SENSOR CHECK

M1173050400149
<2.4L ENGINE>
To inspect these parts, refer to GROUP 13A, Multiport Fuel
<3.8L ENGINE>
To inspect these parts, refer to GROUP 13B, Multiport Fuel
ENGINE COOLANT TEMPERATURE SENSOR

CHECK
M1173008100705
<2.4L ENGINE>
<3.8L ENGINE>
CRANKSHAFT POSITION SENSOR CHECK

M1173008300356
<2.4L ENGINE>
<3.8L ENGINE>
TSB Revision
EMISSION CONTROL
REMOVAL AND INSTALLATION <2.4L ENGINE>

M1173010500498
Pre-removal and Post-installation Operation

• Battery Removal and Installation.
• Air Intake Hose Resonator Removal and Installation
(Refer to GROUP 15, Air Cleaner P.15-4).
24 ± 3 N·m
18 ± 2 ft-lb
1
N 3
2
AC406866 AB

1. EGR VALVE CONNECTOR 2. EGR VALVE
>>A<< 3. EGR VALVE GASKET
INSTALLATION SERVICE POINT

.
>>A<< EGR VALVE GASKET INSTALLATION

Install the EGR valve gasket as shown in the illustration.
GASKET
NOTCHED
PART
NOTCHED
PART AC406867AB
TSB Revision
EMISSION CONTROL
17-109
REMOVAL AND INSTALLATION <3.8L ENGINE>
M1173010500487
Pre-removal and Post-installation Operation

Strut Tower Bar Removal and Installation (Refer to GROUP
42, Strut Tower Bar P.42-12).
1
24 ± 3 N·m
18 ± 2 ft-lb
3N
AC406789 AB

1. EGR VALVE CONNECTOR 2. EGR VALVE
>>A<< 3. EGR VALVE GASKET
INSTALLATION SERVICE POINT

.
>>A<< EGR VALVE GASKET INSTALLATION

Install the EGR valve gasket as shown in the illustration.
GASKET
NOTCHED
PART
NOTCHED
PART
AC406790 AB
TSB Revision
EMISSION CONTROL
EVAPORATIVE EMISSION CANISTER AND FUEL TANK PRESSURE RELIEF

VALVE
M1173004800412
3 13
8 14
9
11 10
5
7
2
1
12
AC406791AB

1. EVAPORATIVE EMISSION 7. EVAPORATIVE EMISSION
VENTILATION SOLENOID CANISTER
CONNECTOR 8. VENT HOSE C
2. WIRING HARNESS CLAMP 9. AIR FILTER
CONNECTION 10. VENT HOSE B
3. VENT HOSE C AND VENT PIPE 11. EVAPORATIVE EMISSION
CONNECTION VENTILATION SOLENOID
4. VAPOR HOSE 12. EVAPORATIVE EMISSION
5. PURGE HOSE ASSEMBLY CANISTER BRACKET
• EVAPORATIVE EMISSION 13. VENT PIPE
CANISTER AND CANISTER 14. VENT HOSE D
BRACKET ASSEMBLY
6. VENT HOSE A
TSB Revision
EMISSION CONTROL
17-111
INSPECTION
M1173004900174

SOLENOID CHECK
1. Connect a hand vacuum pump to nipple (A) of the solenoid.
2. Check air tightness by applying a vacuum with voltage
applied directly from the battery to the evaporative emission
ventilation solenoid and without applying voltage.
BATTERY VOLTAGE NORMAL CONDITION
Applied Vacuum maintained
A Not applied Vacuum leaks
AC406792 AB
3. Measure the resistance between the terminals of the

solenoid.
AC406793
CATALYTIC CONVERTER
GENERAL DESCRIPTION (CATALYTIC CONVERTER)
M1173005300131
The three way catalytic converter, together with the When the mixture is controlled at stoichiometric
closed loop air-fuel ratio control based on the oxygen air-fuel ratio, the three way catalytic converter pro-
sensor signal, oxidizes carbon monoxides (CO) and vides the highest purification against the three con-
hydrocarbons (HC), also reduces nitrogen oxides stituents, namely, CO, HC and NOx.
(NOx).
TSB Revision
SPECIFICATIONS
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1173006400432
ITEM SPECIFICATION
Emission control system
EGR valve bolt 24 ± 3 N⋅ m (18 ± 2 ft-lb)
Engine control system
Accelerator pedal assembly nut 13 ± 2 N⋅ m (111 ± 22 in-lb)
SERVICE SPECIFICATIONS
M1173000300620
ITEM STANDARD VALUE

Emission control system
EGR valve (Stepper Motor) connector resistance [at 20° C (68° F)] Ω 20 − 24
Evaporative emission purge solenoid coil resistance [at 20° C (68° F)] Ω 22 − 26
Evaporative emission ventilation solenoid coil resistance [at 20° C (68° F)] Ω 17 − 21
Purge flow cm3/s (SCFH) [at 80 − 95° C (176 − 205° F) with sudden revving] 20 (2.5)
TSB Revision

GR00000300 17

Uploaded by

Copyright:

Available Formats

GR00000300 17

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GR00000300 17

Uploaded by

Copyright:

Available Formats

17-1

ENGINE CONTROL . . . . . . . . . . 17-3 DIAGNOSTIC TROUBLESHOOTING

EMISSION CONTROL . . . . . . . . 17-90 FUEL TANK DIFFERENTIAL PRESSURE

DIAGNOSIS . . . . . . . . . . . . . . . . . . 17-90 EXHAUST GAS RECIRCULATION (EGR)

ENGINE CONTROL SYSTEM DIAGNOSIS

SYMPTOM INSPECTION PROCEDURE REFERENCE PAGE

INSPECTION PROCEDURE 1: Throttle Valve will not Fully Open or Close

TROUBLESHOOTING HINTS (THE MOST

• Malfunction of the ECM <M/T> or PCM <A/T>.

STEP 1. Using scan tool MB991958, read the diagnostic

STEP 2. Retest the system.

INSPECTION PROCEDURE 2: Accelerator Pedal Operation not Smooth (Over Acceleration)

TROUBLESHOOTING HINTS (THE MOST

STEP 1. Check if the accelerator pedal is installed

STEP 2. Using scan tool MB991958, read the diagnostic

STEP 3. Retest the system.

TOOL TOOL NUMBER AND SUPERSESSION APPLICATION

REMOVAL STEPS REMOVAL STEPS (Continued)

ACCELERATOR PEDAL ASSEMBLY

AUTO-CRUISE CONTROL SYSTEM DIAGNOSIS

HOW TO CONNECT THE SCAN TOOL (MUT-III).

HOW TO READ DIAGNOSTIC TROUBLE CODES

WHEN THE DIAGNOSTIC TROUBLE CODE NO.15 IS WHEN NO DIAGNOSTIC TROUBLE

HOW TO READ DATA LIST

HOW TO DIAGNOSE THE CAN BUS LINE

DIAGNOSTIC TROUBLE CODE PROCEDURES

DTC P15: Auto-cruise Control Switch System

Auto-cruise Control Switch System Circuit

ECM <M/T> OR PCM <A/T>

CONNECTORS: B-18, B-19 CONNECTOR: C-24

B-18 HARNESS B-19 HARNESS

CONNECTORS: C-302, C-303, C-306

C-302 HARNESS C-303 HARNESS

• When the "CRUISE" (MAIN) switch is "ON": 0 −

CIRCUIT OPERATION 0.3 volt

TROUBLESHOOTING HINTS (THE MOST

STEP 2. Measure the power supply voltage at auto-cruise

STEP 3. Measure the power supply voltage at ECM <M/T>

SPECIAL TOOL 18-PIN CONNECTOR

STEP 4. Check ECM <M/T> or PCM <A/T> connector B-18

STEP 5. Check the harness for short circuit to ground

STEP 6. Check intermediate connector C-24, auto-cruise

C-24 MALE SIDE CONNECTOR

CONNECTORS: C-302, C-303, C-306

C-302 HARNESS C-303 HARNESS

STEP 7. Check the harness wire between ECM <M/T> or

STEP 8. Check the clock spring.

STEP 9. Measure the ground voltage at auto-cruise control

(4) Measure the ground voltage between auto-cruise control

STEP 10. Measure the ground voltage at ECM <M/T> or

SPECIAL TOOL 23-PIN CONNECTOR

STEP 11. Check ECM <M/T> or PCM <A/T> connector B-19

STEP 12. Check ECM <M/T> or PCM <A/T> connector B-19,

C-24 MALE SIDE CONNECTOR

C-302 HARNESS C-303 HARNESS

STEP 13. Check the harness wire between ECM <M/T> or

STEP 14. Check the clock spring.

STEP 15. Check auto-cruise control switch connector