3PDT 01

3PDT-01
FX TYPE: Bypass
Enclosure Size: 1590B and up
© 2019 madbeanpedals
Overview
The 3PDT-01 is a simple bypass PCB designed to work with most mbp projects as well as any DIY
project utilizing true bypass operation.
Part Value Type Rating

CLR your choice Metal / Carbon Film 1/4W
LED any 3 or 5mm
3PDT Lug
Terms of Use: You are free to use purchased 3PDT-01 circuit boards for both DIY and small commercial operations. You may not
offer 3PDT-01 PCBs for resale or as part of a “kit” in a commercial fashion. Peer to peer re-sale is fine, though.
Technical assistance for your build(s) is available via the madbeanpedals forum. Please go there rather than emailing me for
assistance on builds. This is because (1) I’m not always available to respond via email in a timely and continuous manner, and (2)
posting technical problems and solutions in the forum creates a record from which other members may benefit.
Notes 3PDT-01
The 3PDT-01 board is used for true bypass switching on your pedal builds. It’s designed to be flexible enough
to work with many different types of PCBs, not just madbeanpedals projects. Different wiring applications are
shown in the following pages of this document.
The 3PDT-01 board is designed for effect input grounding. IOW, then the effect circuit is bypassed, its input
is sent to ground. This can be helpful in reducing switching noise in some cases and in general it is good
practice. The 3PDT-01 PCB will fit either solder lug or PCB pin mount 3PDT switches. Note that these are
designed for the ubiquitous “blue” (CIC) switches. Other manufacturers may have different pin spacing but all
the ones I’ve tried so far have fit fine.
WOW! MANY PADS! SO CONNECTING!
DC IN: Connects directly to the DC Jack. This is only used when you are soldering the indicator LED to the
3PDT board.
DC OUT: When using the DC IN pads, the DC OUT is used to connect power to the effect PCB.
INPUT/OUTPUT JACK (SIDES): For builds that do not have top-mounted jacks. These connect directly to
their respective jacks.
GROUND: To connect ground between the 3PDT-01 board and your effect PCB. Note: you only need one
ground connection between the boards so if you are using the DC OUT connection, you do not need to
connect the GROUND pad to the effect PCB.
LED CATHODE (-): Used for mbp style boards that have the indicator LED mounted on the effect PCB. This
pad connects the 3PDT ground to the LED cathode to illuminate the LED when the effect is turned on.
EFFECT INPUT/OUTPUT: To connect the switch to the circuit input and output (always used).
INPUT/OUTPUT JACK (TOP): Used for mbp style boards that have top mounted switches (for example, on
many of the 125B and 1590BB builds).
CLR: Used for a current limiting resistor on the LED. This is only used when mounting an LED to the 3PDT-01
board. It is not needed when you are using an LED mounted to the effect PCB.
madbeanpedals
Wiring Diagram1 3PDT-01
This is a typical of example of a lot of PCB designs. The effect PCB has four connections (In,
+, - , Out). In this case you will use a bypass LED soldered directly to the 3PDT-01 board (or
wired if you prefer to place the LED somewhere else). The current limiting resistor is used,
as well. This can be as low as 1k but it really depends on the type of LED you are using and
how bright you want it to be. Higher resistance values will dim the LED.
madbeanpedals
Here is an example of a typical mbp 1590B board. The LED indicator is soldered to the
8-Ball PCB which also has the CLR already on it. The DC Jack is connected directly to the
effect PCB, as well.
madbeanpedals
Finally, here is an example of a design that uses top mounted jacks. Like
the previous example, the LED is mounted on the effect board. We can
ignore all the pads on either side of the 3PDT-01 board, as well.
madbeanpedals
1590B Drill Guide 3PDT-01
Note: Drill Guides are approximate and may require tweaking depending on the types of jacks, switches and pots you use.
This template shows a typical layout for a 1590B using the 3PDT-01.
This shows the exact footprint of the 3PDT-01 PCB. The LED is 12.6mm
from the center of the 3PDT.
madbeanpedals
Schematic 3PDT-01
madbeanpedals

3PDT 01

Uploaded by

Copyright:

Available Formats

3PDT 01

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3PDT 01

Uploaded by

Copyright:

Available Formats

3PDT-01

Part Value Type Rating

WOW! MANY PADS! SO CONNECTING!

You might also like