Is 6392

SUPPLIED BY BOOK SUPPLY BUREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER GENERATION CORPORATION
LTD. - VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.21.151.10) VALID UPTO 4/19/2022

UREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER GENERATION CORPORATION LTD. - VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.2
भारतीय मानक IS 6392 : 2020
Indian Standard
स्टील पाइप फ्लैजेंस — विशिष्टि

( पहला पनु रीक्षण )
Steel Pipes Flanges — Specification

( First Revision )
ICS 23.040.60; 77.140.75
© BIS 2020
भारतीय मानक ब्रयू ो

B U R E A U O F I N D I A N S TA N D A R D S
मानक भवन, 9 बहादरु शाह ज़फर मार्ग, नई िदल्ली – 110002
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI-110002
www.bis.gov.in
www.standardsbis.in
June 2020 Price Group 14

SUPPLIED BY BOOK SUPPLY BUREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER GENERATION CORPORATION LTD. - VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.21.151.10) VALID UPTO 4/19/2022
Steel Tubes, Pipes and Fittings Sectional Committee, MTD 19
FOREWORD
This Indian Standard (First Revision) was adopted by the Bureau of Indian Standards, after the draft finalized
by the Steel Tubes, Pipes and Fittings Sectional Committee had been approved by the Metallurgical Engineering
Division Council.
This standard was first published in 1971. While reviewing this standard in the light of trade practices being
followed in the country in this field, and experience gained during these years, the Committee decided to revise
this standard.
In this revision the following modifications have been made:
a) All referred standards have been incorporated under clause 2 (Reference), and all the footnotes for
reference of standards have been deleted.
b) Repair clause 3.4 has been incorporated.
c) For the information of designers the high temperature properties of steels, wherever available, have been
given in note 3 under clause 4.2.3.
d) Machining of flanges, parallel face tolerance have been increased from 1deg to 2 deg.
e) Galvanizing on flanges if required, have been introduced and refer test have been incorporated.
f) Thread identification have been properly specified under 15.1.4.
g) Sampling clause 9 of flanges have been introduced.
h) Flat face flanges clause 7.4 has been introduced as optional subject to purchase’s requirements.
j) All tolerances have been modified in a table format under Table 43.
k) Appendix A, Table 43, Table 44 and Table 45 of the old standards have been withdrawn.
m) Maximum inside dia. of screwed flanges have been specified in Table 44.
While revising the standard, considerable assistance has been drawn from the following publications:
ISO 7005-1: 2011Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
BS 4504 section 3.1:1989 Circular flanges for pipes, valves and fittings (PN designated), issued by the British
Standards Institution (BSI).
This standard contains clauses 1.3, 6.2, 6.2.1, and 8.1 which call for an agreement between the manufacturer and
the purchaser.
For the purpose of deciding whether a particular requirement of this standard is complied with the final
value, observed or calculated, expressing the result of a test or analysis shall be rounded off in accordance with
IS 2 : 1960 ʻRules for rounding off numerical values ( revised )ʼ. The number of significant places retained in the
rounded off value should be the same as that of the specified value in this standard.
IS 6392 : 2020
Indian Standard
STEEL PIPE FLANGES — SPECIFICATION
( First Revision )
1 SCOPE
IS No. Title
1.1 This standard covers the requirements for cast, 1364 (Parts 1 Hexagon head bolts, screws and
forged and plate or flat steel pipe flanges of the to 6) : 2018 nuts of product grades a and b
following types for use in industry for oil, water, steam, 1367 (Parts 1 Technical supply conditions for
air, gas and chemical services: to 20) threaded steel fasteners
a) Integral, 1387 : 1993 General requirements for the supply
b) Welding neck, of metallurgical materials
c) Plate, 1570 (Parts 1 Schedules for wrought steels
d) Screwed boss, to 7)
e) Slip-on boss, 1875 : 1992 Carbon steel billets, blooms, slabs
f) Loose flanges for welded-on lapped pipe ends ; and bar for forgings-specification
and 2002 : 2009 Steel plates for pressure vessels for
g) Blank. intermediate and high temperature
service including boilers
1.2 This standard does not specify limitations on the
use of various methods of attachment of flanges to 2004 : 1991 Carbon steel forging for general
pipe or other equipment. The adequacy for operating engineering purpose — Specification
conditions of any method of attachment specified (third revision)
should be determined by the designer of the piping or 2062 : 2011 Hot rolled medium and high tensile
equipment. structural steel — Specification
(seventh revision)
1.3 The types and materials of gaskets used shall be
agreed between the purchaser and the manufacturer. 2611 : 1964 Specification for carbon chromium
molybdenum steel forgings for high
NOTES:
temperature service
1 The term ‘plate flange’ indicates the shape of the flange, as
the flanges are not necessarily made from steel plate but may 2629 : 1985 Recommended practice for hot-dip
be made from forged or cast steel. galvanizing of iron and steel (first
2 The term ‘integral flange’ applies to flanges integral with revision)
pipes, valves and fittings.
2633 : 1986 Methods for testing uniformity
2 REFERENCES of coating on zinc coated articles
(second revision)
The following standards contain provisions which,
2856 : 1999 Carbon steel castings for pressure
through reference in this text, constitute provisions of
containing parts suitable for fusion
this standard. At the time of publication, the editions
welding — Specification (fourth
indicated were valid. All standards are subject to
revision)
revision, and parties to agreements based on these
standards are encouraged to investigate the possibility 3038 : 2006 Martensitic stainless steel and alloy
of applying the most recent editions of the standards steel castings for pressure containing
indicated below: parts suitable for high temperature
service (fourth revision)
IS No. Title 3658 : 1999 Code of practice for liquid penetrant
554 : 1999 Pipe threads where pressure tight flaw detection
joints are made on the threads- 3703 : 2004 Recommended practice for magnetic
dimension, tolerances and particle flaw detection
designation (fourth revision)
1
IS 6392 : 2020
carbon steel is used, it shall have a tensile strength of

IS No. Title
415 N/mm2, Min ( 1 kgf = 9.81 N ).
4367 : 1991 Alloy steel forgings for general
industrial use — Specification ( first 3.2.1 For temperatures up to 450°C, carbon steel bolts,
revision) studs and nuts may be used.
4711 : 2008 Methods for sampling of steel pipes, 3.2.2 For temperatures higher than 450°C bolts and
tubes and fittings studs shall be of alloy steel and nuts shall be of carbon
4736 : 1986 Hot dip zinc coatings on mild steel or alloy steel of different grade. For bolts less than
tubes ( first revision) 12 mm size alloy steel nuts shall be used.
8999 : 2003 Pipe threads where pressure tight 3.3 Steel pipe flanges shall be supplied according to
joints are made on the threads — IS 1387 and all threaded fasteners according to IS 1367.
Verification by means of limit
gauges ( first revision) 3.4 Repairs
3.4.1 Where not otherwise prohibited by the applicable
3 MATERIAL material standard, repairs by welding are permitted
when there is a proven method.
3.1 Other than high temperature use, the materials
3.4.2 Any filler rod used for weld repairs shall be such
shall be those given in Table 1 except that alternative
as to produce a weld having characteristics similar to
materials may be used provided that their mechanical
those of the parent metal. Flanges shall be heat treated
properties (tensile strength, yield stress and percent
after repair welding when the material specification
elongation) shall not be less than the value as specified
requires such treatment.
in IS 2002 Gr-1.
3.2 Bolting Material 4 CLASSIFICATION
Both bolts and nuts shall be in accordance with 4.1 This Standard applies to flanges of the following
IS 1364. For alloy steel studs or bolts, nuts of a class designations : Classes 0.1, 0.25, 0.60, 1.0, 1.6,
similar steel, but of a different grade shall be used. If 2.5, 4.0, 6.4, 10.0 and 16.0.
Table 1 Material Specification

( Clauses 3.1 and 4.2.1 )
Sl No. Classification Specification

(1) (2) (3)
a) Forgings
i) Carbon steel IS 2004, Classes 2 and 3
ii) Carbon molybdenum steel IS 1570 (Part 4), Grade 20 Mo6 with 0.050, Max, of
S and P
iii) Chrome-molybdenum steel
1) 1 percent chromium — 0.5 percent molybdenum steel IS 2611
2) 2.25 percent chromium — 1 percent molybdenum steel IS 4367, Grade 10 Cr9Mo10
iv) Carbon steel IS 1875
b) Castings
v) Carbon steel IS 2856, Grades 2 and 3
vi) Chrome-molybdenum steel
1) Carbon molybdenum steel IS 3038, Grade2
2) 2.25 percent chromium — 0.5 percent molybdenum steel IS 3038, Grade 4
3) 2.25 percent chromium — 1 percent molybdenum steel IS 3038, Grade 5
c) Rolled Plates
vii) Carbon steel IS 2002, Grades 1,2 and 3
viii) Steel IS 2062
2
IS 6392 : 2020
4.2 Pressure Temperature Ratings between the steel-maker and the inspecting authority,
Repair areas of castings should be re-examined in
The class designations represent the primary service accordance with 3.2.3(a) and should be shown to be free
pressure ratings of the flanges in newtons/millimetre from harmful defects. In all other cases a factor of 0.75
square. shall be used instead of 0.90.
2 The minimum tensile strength, yield strength at room
4.2.1 The allowable stress values for the different temperature have been specified in the relevant specifications.
materials given in Table 1 shall be determined by 3 For high temperature properties, IS 2002, IS 2611and
dividing the appropriate properties of the material by IS 4367 recommended as per application.
the factors given in the table below and taking the
lowest value. 5 DESIGNATION
4.2.2 Pressure ratings at different temperatures for 5.1 The flanges shall be designated by the nominal
flanges made from different types of steel mentioned in bores of their respective pipes as shown in column 1 of
Table 1 may he arrived at by the formula given below: Tables 2 to 42. In addition to the nominal bore size the
rated pressure, type, grade and standard number of the
Pressure ratings at primary service temperature, T1 material for flange should also be given to completely
Pressure ratings at any other temperature, T2 specify the flange.
Allowable stress value at primary service 6 FLANGES

temperature, T1
6.1 Dimensions
= ——————————————————
Allowable stress value at any temperature, T2 The dimensions of various types of flanges for different
pressure classes conforming to this standard shall be as
4.2.3 Other properties are given below: given in Tables 2 to 42.
Property Carbon and Low Alloy 6.2 Machining of Flanges
Carbon Steels The backs of integral flanges shall be machined except
Manganese that the backs of integral forged flanges need not be
Steels machined provided they are parallel with the whole
Certified or specified 1.5 -1.5 face within 2 deg. Where machining is carried out it
minimum yield (or 0.2 may be either by spot facing at the bolt holes or by back
percent proof) stress facing at the option of the manufacturer
at design temperature
6.2.1 The backs of other flanges may be left unmachined
Specified minimum 3.0 3.0 unless machining is required by the purchaser.
tensile stress at room
temperature 6.2.2 Unless otherwise specified by the purchaser all
Average stress to 1 1 bolt holes shall be drilled, equally spaced on the pitch
produce, rupture in circle diameter, in the case of integral flanges the bolt
10 000 h at design holes shall be drilled off centres.
temperature
7 TOLERANCES
NOTES:
1 In the case of castings, the above factors shall be divided by
7.1 Tolerances on flange as given in Table 43.
a quality factor of 0.75. However, a quality factor of 0.9 shall
7.2 Finish of Joint Surfaces
be used when the following requirements have been met with:
a) Each casting has been radiographically examined at all The finish of joint faces and the type of gasket to be
critical locations and found free from harmful defects, or used are not specified in this standard due to the wide
the castings have been fully machined to such an extent range of applications for which the flanges can be
that all critical sections are exposed for the full thickness used. However, the recommended joint face finish to
as in the case of tube plates with holes spaced not further
be provided on flanges used for steam, feed, water,
apart than the thickness of the casting.
and other fluids for which similar standards of joint
b) All castings have been examined at all critical locations
using magnetic particle, or penetrant fluid procedure (see
tightness are required is as follows:
IS 3658 and IS 3703 ) or by grinding or machining and a) Flanges Up to 300 mm Nominal Size Inclusive —
etching. A continuous spiral groove produced by a 1.5 mm
c) Castings found to be defective have been rejected or radius round-nosed tool at a feed of approximately
repaired to the satisfaction of the inspecting authority. If 0.8 mm per revolution with approximate depth
repairs by welding are carried out, the castings should
of 0.5 mm.
be subsequently stress-relieved or heat-treated as agreed
3
IS 6392 : 2020
b) Flanges Over 300 mm Nominal Size — A 9.2 Re-test

continuous spiral groove produced by a 3 mm Should any one of the pieces first selected fail to pass
radius round-nosed tool at a feed of approximately any of the tests specified, two further samples shall be
1.2 mm per revolution with approximate depth of selected for testing in respect of each failure. Should
0.8 mm. the test pieces from both these additional samples
7.3 Joint Faces pass, the materials shall be deemed to comply with
the requirements of particular test. Should the test
Steel flanges shall have raised joint faces except that pieces from either of these additional samples fail,
blank flanges may be flat faced or have a spigot at the the materials represented by the test samples shall be
option of the manufacturer. deemed as not complying with the standard.
7.4 Flat Face
10 HYDRAULIC TESTING OF FLANGES
Manufacturers are permitted to manufacture flat face
flanges as per the requirement of the purchaser. In flat This standard does not specify the hydraulic test
face flanges ‘b’ (including raised face f) will be the pressures for flanged pipes or components, details
thickness of flange. of which should be obtained from the appropriate
standards which specify test pressures for pipes or
8 ATTACHMENT OF FLANGES components but the test pressure applied to the joint
shall not exceed 1.5 times the nominal pressure for the
8.1 The method of securing flanges (other than the flanges and the same maintained for at least 10 s shall
integral flanges) to pipes and fittings shall be in not show any leakage.
accordance with the appropriate application standard.
Where there is no application standard the method of 11 INSPECTION
attachment shall be subject to agreement between the
purchaser and the manufacturer. 11.1 The purchaser or his representative shall have
free access at all reasonable times to those parts of
8.2 Flanges machined according to the tolerances in 7 the manufacturer’s works actually engaged upon his
shall be prepared for attachment to pipe as in 8.2.1 contract and shall be at liberty to inspect at any stage of
to 8.2.3. manufacture the materials covered by such contract. He
shall be at liberty to reject any material which does not
8.2.1 Screwed Flanges comply with the requirements of this standard.
Unless otherwise specified, screwed flanges shall have
parallel threads. All threads shall be in accordance with 11.1.1 When the purchaser or his representative desires
IS : 554. Gauging in accordance with IS 8999 shall to witness the specified tests on the materials covered
be considered as an adequate test for conformity of by his contract, the manufacturer shall notify him
threads. Maximum inside diameter shall be as given in sufficiently in advance of the tests to enable him to be
Table 44. present.
8.2.2 Plate Flanges, Slip-on Boss Flanges, and Loose 11.2 Defects which do not impair the strength of the
Flanges for welding on lapped pipe ends flanges may be welded by a procedure approved by the
purchaser. They shall be cleaned out to sound metal
These shall be machined to in the bore to a diameter as before welding, and shall be submitted to the purchaser’s
given in the respective Table. inspector for approval in this condition, after which
8.2.3 Welding Neck Flanges they may be welded if the purchaser so agrees. After
welding, flanges shall be heat-treated, except that welds
These shall be machined in the bore to a diameter to required for finish” and appearances only need not be
be specified by the purchaser, and suitably prepared heat treated, if approved by the purchaser. When the
for welding to pipes and fittings. The thickness of welding of defects is permitted, the welding rod shall
the portion of the flange which connects it to the pipe be, such as to produce a weld having characteristics
should be not less than the pipe thickness nor more than similar to the parent metal.
3 mm thicker. If the difference is more than 3 mm, it
may be negotiated in a slope of 1 in 5. 12 DETAILS TO BE SUPPLIED BY THE
PURCHASER WHEN ORDERING FLANGES
9 SAMPLING OF FLANGES
The following information shall be supplied by the
9.1 The procedure for sampling of flanges for various purchaser when placing an order or making an enquiry:
tests shall be given in IS 4711. a) Nominal size, nominal pressure, type of flange
(including type of screwing whether taper or
4
IS 6392 : 2020
parallel [see Tables 2 to 42 and materials (see 3.1 15.1.4 Thread Identification
and Table 1)]; The marking shall be cast or stamped on the flanges to
b) Whether test certificates of the material are indicate the type of thread used. For internal parallel,
required; thread shall be marked with the word ‘Rp’ and for that
c) Details of bolting ( if required ) (see 3.2 ); of taper ‘Rc’.
d) Whether flanges are to be machined (see 6.2 and 15.1.5 Size
6.2.1); and
Numerals denoting the nominal pipe size in mm size
e) Details of the machining for the attachment of markings but may be omitted from reducing flanges.
flanges (see 8 ).
15.1.6 Omission of Markings
13 GALVANIZING
On flanges of such size or shape that will not permit
13.1 Where flanges are required to be galvanized, the full markings, the markings may be omitted with
zinc coating shall be done in accordance with IS 4736 the approval of the purchaser keeping the minimum
and the requirements as given in 13.1.1 to 13.1.3. markings as under:
a) Size,
13.1.1 Mass of Zinc Coating
b) Materials specification,
Mass of zinc coating shall be determined in accordance
c) Class rating, and
with IS 4736 and shall not be less than 360 g/m2. Each
flange shall be the test piece. d) Manufacturer’s name or trade-mark.
13.1.2 Uniformity of Zinc Coating The remaining information should be made available to
the purchaser, if required.
The test for uniformity of zinc coating on flanges shall
be done on each flange in accordance with IS 2633 and 15.2 BIS Certification Marking
shall withstand 5 one minute dips. The product(s) conforming to the requirements of
13.1.3 Adhesion Test this standard may be certified as per the conformity
assessment schemes under the provisions of the Bureau
The adhesion of zinc coating on flanges shall be of Indian Standards Act, 2016 and the Rules and
determined by pivoted hammer test in accordance with Regulations framed thereunder, and the products may
IS 2629. be marked with the Standard Mark.
13.1.4 Screwed flanges shall be galvanized before
16 PRESERVATION AND PACKING
screwing.
16.1 After inspection, and before despatch, flanges
14 WORKMAMSHIP
shall, if necessary, be dried and cleaned.
Flanges shall be clearly finished and reasonably
free from scale, surface flaws, laminations and other 16.1.1 Threaded and machined surfaces shall be well-
defects. The screw threads of flanges shall be clean and covered with an approved rust preventive material that
well cut. will not become fluid and run off at 65°C.
16.1.2 Exposed faces of flanges shall be protected
15 MARKING
over their entire surface with a suitable close-fitting
15.1 Flanges manufactured in accordance with this protector securely attached at not less than four points.
specification shall be marked as in 15.1.1 to 15.2. The type of protector and method of attachment shall
be approved by the purchaser.
15.1.1 Manufacturer’s name or trade-mark.
16.2 Packing
15.1.2 Class Rating
16.2.1 Flanges shall be bundled by bolting them together
Numerals giving the primary service pressure for which or securing them with wire of suitable strength passed
the product is designated. through the bolt holes in such a manner that the flanges
15.1.3 Materials Identification are paired and no flange facings remain exposed.
Carbon steel flanges shall be marked with the word 16.2.2 Other methods of preparation for dispatch shall
“steel”, and alloy steel flanges shall be marked with be subject to agreement between the purchaser and the
word “alloy”. manufacturer.
5
IS 6392 : 2020
Table 2 Welding Neck Flanges

( Clauses 5.1 and 6.1 )
Nominal pressure 0.25 N/mm2.

All dimensions in millimetres.

NOTETABLE
— For2nominal sizes 10 to 1 000 mm, use Table 4.
WELDING NECK FLANGES
h2
Ø d1
Ø d2 r
h1
b
Ø d3
f
Ø d4
Øk
ØD
*These dimensions are not to scale.

TABLE 3 PLATE FLANGES FOR WELDING
Nom Pipe Flange RaisedØFace

d1 Bolting Drilling Neck
Size o.d.
d1
Ø d2
D b h1 d4 f No. d2 k d3 h2 ≈ r
1200 1220 1375 26 70 1280 5 M27 32 30 b
1320 1245 16 16
1400 1420 1575 26 70 1480 5 M27 36 30 1520 1445 16 16
Ø d4 f
1600 1620 1790 26 80 1690 5 M27 40 30 1730 1645 20 16
Øk
1800 1820 1990 26 80 1890 5 M27 44 30 1930 1845 20 16
ØD
2000 2020 2190 26 80 2090 5 M27 48 ! 30 2130 2045 22 16
6
h2
Ø d1
Ø d2 r
h1
IS 6392 : 2020
b
Table 3 Plate Flanges for Welding

Ø d3
( Clauses f
Ø d4 5.1 and 6.1 )
Øk
NominalØ pressure
D 0.25 N/mm2.
All dimensions in millimetres.
NOTE — For nominal sizes 10 to 1 000 mm, use Table 5.

Ø d1
Ø d2
Ø d4 f
Øk
ØD
‘These dimensions are not to scale*
Nom Pipe Flange Raised Face Bolting Drilling

Size o.d.
d1
D Bore b d4 f No. d2 k
Dia.
1200 1220 1375 36 1280 5 M27 32 30 1320
As agreed between
the purchaser and
the manufacturer
1400 1420 1575 42 1480 5 M27 36 30 1520

1600 1620 1790 46 1690 5 M27 40 30 1730
1800 1820 1990 52 1890 5 M27 44 30 1930
2000 2020 2190 58 2090 5 M27 48 30 2130
7
IS 6392 : 2020

( Clauses 5. 1 and 6.1 )

All dimensions in millimeters.
TABLE 4 WELDING NECK FLANGES
h2
Ø d1
Ø d2 r
h1
b
Ø d3 f
Ø d4
Øk
ØD

Ø d1
Nom Pipe Flange Raised Face Bolting Drilling Neck
Size o.d. h2
D b h1 d4 f No. d2 k d3 r
d1 ≈
10 17.2 75 12 28 35 2 M10 4 11 50 26 6 4
15 21.3 80 12 30 40 2 M10 4 11 55 30 6 4
Ø d2
20 26.9 90 14 32 50 2 M10 4 11 65 38 6 4
25 33.7 100 14 35 60 2 M10 4 11 75 42 6 4
b
32 42.4 120 14 35 70 2 M12 4 14 90 55 6 6
Ø d4 f
40 48.3 130 14 38 80 3 Ø kM12 4 14 100 62 7 6

ØD
50 60.3 140 14 38 90 3 M12 4 14 110 74 8 6
65 76.1 160 14 38 110 3 M12 4 14 130 88 9 6
80 88.9 190 16 42 128 3 M16 4 18 150 102 10 8
100 114.3 210 16 45 148 3 M16 4 18 170 130 10 8
125 139.7 240 18 48 178 3 M16 8 18 200 155 10 8

150 168.3 265 18 48 202 3 M16 8 18 225 184 12 10
200 219.1 320 20 55 258 3 M16 8 18 280 236 15 10
250 273 375 22 60 312 3 M16 12 18 335 290 15 12
300 323.9 440 22 62 365 4 M20 12 22 395 342 15 12
350 355.6 490 22 62 415 4 M20 12 22 445 385 15 12

400 406.4 540 22 65 465 4 M20 16 22 495 438 15 12
8
IS 6392 : 2020
Table 4 ( Concluded )

Size o.d. h2
D b h1 d4 f No. d2 k d3 r
d1 ≈
500 508 645 24 68 570 4 M20 20 22 600 538 15 12
600 609.6 755 24 70 670 5 M24 20 26 705 640 16 12
700 711.2 860 24 70 775 5 M24 24 26 810 740 16 12
800 812.8 975 24 70 880 5 M27 24 30 920 842 16 12

900 914.4 1 075 26 70 980 5 M27 24 30 1 020 942 16 12
1 000 1 016 1 175 26 70 1 080 5 M27 28 30 1 120 1 045 16 16
1 200 1220 1 405 28 90 1 295 5 M30 32 33 1 340 1 248 20 16
1 400 1 420 1 630 32 90 1 510 5 M33 36 36 1 560 1 452 20 16
1 600 1 620 1 830 34 90 1 710 5 M33 40 36 1 760 1 655 20 16

1 800 1 820 2 045 36 100 1 920 5 M36 44 39 1 970 1 855 20 16
2 000 2 020 2 265 38 110 2 125 5 M39 48 42 2 180 2 058 25 16
9
h2
Ø d1
Ø d2 r
UREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER GENERATION CORPORATION LTD. h-1VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.2
IS 6392 : 2020 b
Ø d3
Table 5 Plate Flanges for Welding f
Ø d4
( Clauses 5.1Ø and
k 6.1 )
ØD

Ø d1
Ø d2
Ø d4 f
Øk
ØD
*These dimensions are not to scale

Size o.d. D Bore b d4 f No. d2 k
d1 Dia.
10 17.2 75 18.0 12 35 2 M10 4 11 50
15 21.3 80 22.0 12 40 2 M10 4 11 55
20 26.9 90 27.5 14 50 2 M10 4 11 65
25 33.7 100 34.5 14 60 2 M10 4 11 75
32 42.4 120 43.5 16 70 2 M12 4 14 90
40 48.3 130 49.5 16 80 3 M12 4 14 100

50 60.3 140 61.5 16 90 3 M12 4 14 110
65 76.1 160 77.5 16 110 3 M12 4 14 130
80 88.9 190 90.5 18 120 3 M16 4 18 150
100 114.3 210 116.0 18 148 3 M16 4 18 170
125 139.7 240 141.5 20 178 3 M16 8 18 200

150 168.3 265 170.5 20 202 3 M16 8 18 225
200 219.1 320 221.5 22 258 3 M16 8 18 280
250 273 375 276.5 24 312 3 M16 12 18 335
300 323.9 440 327.5 24 365 4 M20 12 22 395
10
IS 6392 : 2020

d1 Dia.
350 355.6 493 359.5 26 415 4 M20 12 22 445
400 406.4 540 411.0 28 465 4 M20 16 22 495
500 508 645 513.5 30 570 4 M20 20 22 600
600 609.6 755 616.5 32 670 5 M24 20 26 705
700 711.2 860 As agreed between the purchaser and the 34 775 5 M24 24 26 810
800 812.8 975 38 880 5 M27 24 30 920

900 914.4 1 075 42 980 5 M27 24 30 1 020
manufacturer
1 000 1 016 1 175 46 1 080 5 M27 28 30 1 120

1 200 1 220 1 405 56 1 295 5 M30 32 33 1 340
1 400 1 420 1 630 66 1 510 5 M33 36 36 1 560
1 600 1 620 1 830 74 1 710 5 M33 40 36 1 760

1 800 1 820 2 045 84 1 920 5 M36 44 39 1 970
2 000 2 020 2 265 92 2 125 5 M39 48 42 2 180
11
IS 6392 : 2020
Table 6 Screwed Boss Flanges


All dimensions in millimeters
TABLE 6 SCREWED BOSS FLANGES
Ø d1
TAPER 1 IN 6-25
ON DIAMETER
Ø d2
h
b
Ø d3
f
Ø d4
Øk
ØD
TABLE 7 SLIP-ON BOSS FLANGES FOR WELDING
Nom Pipe Flange Raised Face Bolting Drilling Boss

Size o.d. D b h Ø d d4 f No. d2 k d3
1
d1
TAPER 1 IN 6.25
6 10.2 65 10 18 25 2 M10 4
ON DIAMETER11 40 18
8 13.5 70 10 18 30 2 M10 4 11 45 22
Ø d2
10 17.2 75 12 20 35 2 M10 4 11 50 25
h
15 21.3 80 12 20 40 2 M10 4 b 11 55 30
20 26.9 90 14 24 Ø d 50 2 M10 4 11 65 40
3
f
Ø d4
Øk
25 33.7 100 14 24 60 2 M10 4 11 75 50
ØD
32 42.4 120 14 26 70 2 M12 4 14 90 60
40 48.3 130 14 26 80 3 M12 4 14 100 70
50 60.3 140 14 28 90 3 M12 4 14 110 80
65 76.1 TABLE 8 LOOSE
160 14 FLANGES
32 FOR110
WELDED ON
3 LAPPED PIPE ENDS4
M12 14 130 100
Ø d1
80 88.9 190 16 34 128 3 M16 4 18 150 110

100 114.3 210 16 40 148 3 M16 4 18 170 130
CHAMFERED
125 139.7 240 18 44 Ø d5 178 3 M16 8
FOR WELDING 18 200 160
150 165.1 265 18 44 202 3 M16 8 18 225 185
r
Ø d2
ex 45°
Ø d4
Øk
ØD
12
TAPER 1 IN 6-25
ON DIAMETER
Ø d2
UREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER GENERATION CORPORATION LTD.h - VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.2
b
IS 6392 : 2020
Ød
Table 7 Slip-On
3
Boss Flanges for Welding
f
Ø d4
Ø k( Clauses 5.1 and 6.1 )
ØD

TABLE 7 SLIP-ON BOSS FLANGES FOR
All dimensions WELDING
in millimeters.
Ø d1
TAPER 1 IN 6.25
ON DIAMETER
Ø d2
h
b
Ø d3
f
Ø d4
Øk
ØD
TABLE 8 LOOSE FLANGES FOR WELDED ON LAPPED PIPE ENDS

Nom Pipe Flange Ø d1 Raised Face Bolting Drilling Boss
Size o.d. D Bore b h d4 f No. d2 k d3
d1 Dia.
≈ CHAMFERED
Ø d5 FOR WELDING
6 10.2 65 11.5 10 18 25 2 r M10 4 11 40 18
Ø d2
8 13.5 70 15.0 10 18 30 2 M10 4 11 45 22
10 17.2 75 18.0 12 20 35 2 M10 b 4 11 50 25
15 21.3 80 22.0 12 20 40 2 M10 4 11 55 30
ex 45°
20 26.9 90 27.5 14 Ø d 24 50 2 M10 4 11 65 40
4
Øk
ØD
25 33.7 100 34.5 14 24 60 2 M10 4 11 75 50
32 42.4 120 43.5 14 26 70 2 M12 4 14 90 60
40 48.3 130 49.5 14 26 80 3 M12 4 14 100 70
50 60.3 140 61.5 14 28 90 3 M12 4 14 110 80
65 76.1 160 77.5 14 32 110 3 M12 4 14 130 100
80 88.9 190 90.5 16 34 128 3 M16 4 18 150 110

100 114.3 210 116.0 16 40 168 3 M16 4 18 170 130
125 139.7 240 141.5 18 44 178 3 M16 8 18 200 160
150 168.3 265 170.5 18 44 202 3 M16 8 18 225 185
200 219.1 320 221.5 20 44 258 3 M16 8 18 280 240
250 273 375 276.5 22 44 312 3 M16 12 18 335 295

300 323.9 440 327.5 22 44 365 4 M20 12 22 395 355
13
TAPER 1 IN 6.25
ON DIAMETER
Ø d2
h
IS 6392 : 2020
b
Ø d3 for Welded on Lapped Pipe Ends

Table 8 Loose Flanges f
Ø d4
(ØClauses
k 5.1 and 6.1 )
ØD

TABLE 8 LOOSE FLANGES FOR WELDED ON LAPPED PIPE ENDS
Ø d1
CHAMFERED
Ø d5 FOR WELDING
r
Ø d2
ex 45°
Ø d4
Øk
ØD
Nom Pipe Flange Bolting Drilling Pipe End

Size o.d. D b d5 e No. d2 k d4 r
d1 Max
10 17.2 75 10 21 5 M10 4 11 50 35 3
15 21.3 80 10 25 5 M10 4 11 55 40 3
20 26.9 90 10 31 5 M10 4 11 65 50 3
25 33.7 100 12 38 6 M10 4 11 75 60 4
32 42.4 120 12 47 6 M12 4 14 90 70 4
40 48.3 130 12 53 6 M12 4 14 100 80 4

50 60.3 140 12 65 6 M12 4 14 110 90 5
65 76.1 160 12 81 6 M12 4 14 130 110 5
80 88.9 190 14 94 6 M16 4 18 150 128 5
100 114.3 210 14 120 6 M16 4 18 170 148 5
125 139.7 240 14 145 6 M16 8 18 200 178 5

150 168.3 265 14 174 6 M16 8 18 225 202 5
200 219.1 320 18 226 8 M16 8 18 280 258 5
250 273 375 20 281 8 M16 12 18 335 312 5
300 323.9 440 24 333 8 M20 12 22 395 365 5
14
IS 6392 : 2020
Nom Pipe Flange Bolting Drilling Pipe End

d1 Max
350 355.6 490 26 365 8 M20 12 22 445 415 6
400 406.4 540 30 411 8 M20 16 22 495 465 6
500 508 645 32 519 8 M20 20 22 600 570 6
600 609.6 755 36 622 8 M24 20 26 705 670 6
700 711.2 860 40 8 M24 24 36 810 775 6
the purchaser and the

As agreed between
manufacturer.
800 812.8 975 44 8 M27 24 30 920 880 6
900 914.4 1 075 48 8 M27 24 30 1 020 980 6
1 000 1 016 1 175 52 8 M27 28 30 1 120 1 080 6
1 200 1 220 1 405 60 10 M30 32 33 1 340 1 295 8
15
IS 6392 : 2020
Table 9 Plate Black Flanges


NOTE — The two of flanges shown are alternatives at the option of manufacturer.
TABLE 9 PLATE BLACK FLANGES
Ø d2
Øk
ØD
FORM A
Ø d2 b
2 APPROX
Ø d9
Øk
ØD
FORM B
Nom Flange Spigot Bolting Drilling

Size TABLE 10 WELDING NECK FLANGES
D b d9 No. d2 l
10 75 12 - M10 4 11 50
15 80 12 - M10 4 11 55
20 90 14 - M10 4 11 65
25 100 14 - M10 4 11 75
32 120 14 - M12 4 14 90
Ø d1 h2
40 130 14 - M12 4 14 100
50 140 14 - M12 4 14 110
Ø d2 r
65 160 14 55 M12 4 h1 14 130
80 190 16 70 M16 4b 18 150
100 210 16 90 M16 4 18 170
Ø d3 f
Ø d4
125 240 18 115 M16 8 18 200
Øk
150 265 18 140
ØD M16 8 18 225
175 295 20 165 M16 8 18 255
200 320 20 190 M16 8 18 280
250 375 22 237 M16 12 18 335
300 440 22 285 M20 12 22 395

350 490 22 332 M20 12 22 445
400 540 22 380 M20 16 22 495
500 645 24 475 M20 20 22 600
16
Øk
ØD
FORM A
Ø d2 b IS 6392 : 2020
2 APPROX

( Clauses
Ø d9 5.1 and 6.1 )
Øk
ØD
FORMpressure
Nominal B 1 N/mm2.
NOTE — For nominal sizes 10 to 175 mm, use Table 16.

Ø d1 h2
Ø d2 r
h1
b
Ø d3 f
Ø d4
Øk
ØD

Size o.d. D b h1 d4 f No. d2 k d3 h2 r
d1 ≈
200 219.1 340 24 62 268 3 M20 8 22 295 235 16 10

250 273 395 26 68 320 3 M20 12 22 350 292 16 12
300 323.9 445 26 68 370 4 M20 12 22 400 344 16 12
350 355.6 505 26 68 430 4 M20 16 22 460 385 16 12
400 406.4 565 26 72 482 4 M24 16 26 515 440 16 12
500 508 670 28 75 585 4 M24 20 26 620 542 16 12

600 609.6 780 28 80 685 5 M27 20 30 725 642 18 12
700 711.2 895 30 80 800 5 M27 24 30 840 745 18 12
800 812.8 1 015 32 90 905 5 M30 24 33 950 850 18 12
900 914.4 1 115 34 95 1 005 5 M30 28 33 1 050 950 20 12
1 000 1 016 1 230 34 95 1 110 5 M33 28 36 1 160 1 052 20 16

1 200 1 220 1 455 38 115 1 330 5 M36 32 39 1 380 1 255 25 16
1 400 1 420 1 675 42 120 1 535 5 M39 36 42 1 590 1 460 25 16
1 600 1 620 1 915 46 130 1 760 5 M45 40 48 1 820 1 665 25 16
1 800 1 820 2 115 50 140 1 960 5 M45 44 48 2 020 1 868 30 16
2 000 2 020 2 325 54 150 2 170 5 M45 48 48 2 230 2 072 30 16
17
IS 6392 : 2020

Nominal pressure 1 N/mm2.

NOTE – For nominal sizes 10 to 175 mm, use Table 17.

Ø d1
Ø d2
Ø d4
Øk f
ØD
TABLE 12 SLIP-ON BOSS FOR WELDING

Ø d1

d1 Dia. TAPER 1 IN 6-25
ON DIAMETER
200 219.1 340 221.5 24 268 3 M20 8 22 295
Ø d2
250 273 395 276.5 26 320 3 M20 12 h 22 350
b
300 323.9 445 327.5 26 370 4 M20 12 22 400
350 355.8 505 359.5 Ø d3
28 430 4 M20 16 22 460
f
400 406.4 565 411.0 32 Ø d4
482 4 M24 16 26 515
Øk
ØD
500 508 670 513.5 38 585 4 M24 20 26 620
600 609.6 780 616.5 42 685 5 M27 20 30 725
700 711.2 895 46 800 5 M27 24 30 840
the purchaser and the
As agreed between
800 812.8 1 015 52

TABLE 13 LOOSE FLANGES 905WELDED-5ON LAPPED
FOR M30
PIPE ENDS 24 33 950
manufacturer
900 914.4 1 115 56 Ø1d005

1
5 M30 28 33 1 050
1 000 1 016 1 230 62 1 110 5 M33 28 36 1 160

CHAMFERED
1 200 1 220 1 455 74 Ø d5 1 330 5 M36 32 39 1 380
FOR WELDING
Ø d2 r
b
ex 45°
Ø d4
Øk
ØD
18
Ø d1
IS 6392 : 2020
Ø d2 Table 12 Slip-On Boss for Welding

b
Ø d4
NominalØpressure
k 1 N/mm2. f
Ø D
NOTE – For nominal sizes 6 to 65 mm inclusive, use Table 19.

TABLE 12 SLIP-ON BOSS FOR WELDING
Ø d1
TAPER 1 IN 6-25
ON DIAMETER
Ø d2
h
b
Ø d3
f
Ø d4
Øk
ØD
Nom Pipe TABLE 13 Flange Raised Face

LOOSE FLANGES FOR WELDED- Bolting
ON LAPPED PIPE ENDS Drilling Boss
Size o.d. D Bore b h Ø d1 d4 f No. d2 k d3
d1 Dia.
≈
Ø d5 CHAMFERED
FOR WELDING
80 88.9 200 Ø 90.5
d2 20 34 138 3 M16 8 18 160 118
r
b
100 114.3 220 116.0 20 40 158 3 M16 8 18 180 140
ex 45°
Ø d4
125 139.7 250 141.5 22 44 188 3 M16 8 18 210 168
Øk
ØD
150 168.3 285 170.5 22 44 212 3 M20 8 22 240 195
200 219.1 340 221.5 24 44 268 3 M20 8 22 295 237
250 273 395 276.5 26 46 320 3 M20 12 22 350 292
300 323.9 445 327.5 26 46 370 4 M20 12 22 400 344
19
ON DIAMETER
Ø d2
h
UREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER GENERATION CORPORATION LTD. b
- VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.2
IS 6392 : 2020
Ø d3
f
Ø d4
Table 13 Loose Flanges
Ø k for Welded-on Lapped Pipe Ends
ØD

TABLE 13 LOOSE FLANGES FOR WELDED- ON LAPPED PIPE ENDS
Ø d1
Ø d5 CHAMFERED
FOR WELDING
Ø d2 r
b
ex 45°
Ø d4
Øk
ØD
Nom Pipe Flange Bolting Drilling Pipe END

d1 Max
10 17.2 90 14 21 5 M12 4 14 60 40 3
15 21.3 95 14 25 5 M12 4 14 65 45 3
20 26.9 105 14 31 5 M12 4 14 75 58 3
23 33.7 115 16 38 6 M12 4 14 85 68 4
32 42.4 140 16 47 6 M16 4 18 100 78 4
40 48.3 150 16 53 6 M16 4 18 110 88 4

50 60.3 165 16 65 6 M16 4 18 125 102 5
65 76.1 185 16 81 6 M16 4 18 145 122 5
80 88.9 200 18 94 6 M16 8 18 160 138 5
100 114.3 220 18 120 6 M16 8 18 180 158 5
125 139.7 250 18 145 6 M16 8 18 210 188 5

150 168.3 285 18 174 6 M20 8 22 240 212 5
200 219.1 340 20 226 8 M20 8 22 295 268 5
250 273 395 22 281 8 M20 12 22 350 320 5
300 323.9 445 26 333 8 M20 12 22 400 370 5
20
IS 6392 : 2020

Nominal pressure 1 N/mm2

NOTES:
1 The two types of flanges shown are alternatives at the option of the manufacturer.
2 For nominal sizes 10 to 175 mm, use Table 20.
Ø d2
Øk
ØD
FORM A
Ø d2 b
2
APPROX
Ød9
Øk
ØD
FORM B
TABLE 15 INTEGRAL FLANGES

Size
D b D9 No. d2 k
200 340 24 190 M20 8 22 295

250 395 26 237 M20 12 22 350
300 445Ød 2 26 285 M20 r 12 22 400
350 505 26 332 M20 16 22 460
f
400 565 26 380 M24 16 b 23 515
500 670 28 Ød3 475 M24 20 26 620

Ød4
Øk
ØD
Ød1 h2
21
Ød2 r f h1
Ød
Øk
ØD
FORM
UREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER A
GENERATION CORPORATION LTD. - VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.2
IS 6392 : 2020
Ø d2 b
2
Table 15 Integral Flanges APPROX
Ød9
Ø k
ØD
FORM B
NOTE – For nominal sizes 10 to 50 mm, use Table 26.

Ød 2 r
f
b
Ød3
Ød4
Øk
ØD

Nom Flange Raised Face Bolting Drilling Neck
Size D b d4 f No. d2 k d3 r
65 185 18 122 3 M16 4 18 145 93 5

80 200 20 138 3 M16 8 18 160 110 5
100 220 20 158 3 M16 8 18 180 130 5
125 250 22 188 3 M16 8 18 210 159 6
150 285 22 212 3 M20 8 22 240 184 6
Ød1 h2
175 315 24 242 3 M20 8 22 270 211 6

200 340 24 268 3 M20 12 22 295 236 6
250 405 Ød
262 320 3 M24 12 26 r 355
f h1
290 8
300 460 28 378 4 M24 12 26 410 342 8
350 520 30 438 4 M24 16 26 470 b 396 8
400 580 32 490 4 Ød

M27
3 16 30 525 448 10
500 715 36 610 4 M30 Ød4 20 33 650 554 10
600 840 40 725 5 Øk M33 20 36 770 660 10
700 910 42 795 5 M33 24 36 840 760 12
800 1 025 42 900 5 ØD
M36 24 39 950 864 12
900 1 125 44 1 000 5 M36 28 39 1 050 966 12

1 000 1 255 46 1 115 5 M39 28 42 1 170 1 070 12
1 200 1 485 52 1 330 5 M45 32 48 1 390 1 278 15
1 400 1 685 58 1 530 5 M45 36 48 1 590 1 488 15
1 600 1 930 64 1 750 5 M52 40 56 1 820 1 696 18
1 800 2 130 68 1 950 5 M52 44 56 2 020 1 902 18

2 000 2 345 70 2 150 5 M56 48 62 2 230 2 106 18
2 200 2 555 74 2 360 6 M56 52 62 2 440 2 312 18
22
Ød 2 r
f
b
IS 6392 : 2020
Ød3
Ød4
Øk
ØD
Ød1 h2
Ød2 r f h1
Ød3
Ød4
Øk
ØD

d1 ≈
10 17.2 90 14 35 40 2 M12 4 14 60 28 6 4
15 21.3 95 14 35 45 2 M12 4 14 65 32 6 4
20 26.9 105 16 38 58 2 M12 4 14 75 40 6 4
25 33.7 115 16 38 68 2 M12 4 14 85 45 6 4
32 42.4 140 16 40 78 2 M16 4 18 100 56 6 6
40 48.3 150 16 42 88 3 M16 4 18 110 64 7 6

50 60.3 165 18 45 102 3 M16 4 18 125 75 8 6
65 76.1 185 18 45 122 3 M16 4 18 145 90 10 6
80 88.9 200 20 50 138 3 M16 8 18 160 105 10 8
100 114.3 220 20 52 158 3 M16 8 18 180 131 12 8
125 139.7 250 22 55 188 3 M16 8 18 210 156 12 8

150 168.3 285 22 55 212 3 M20 8 22 240 184 12 10
175 193.7 315 24 60 242 3 M20 8 22 270 210 12 10
200 219.1 340 24 62 268 3 M20 12 22 295 235 16 10
250 273 405 26 70 320 3 M24 12 26 355 292 16 12
23
IS 6392 : 2020

d1 ≈
300 323.9 460 28 78 378 4 M24 12 26 410 344 16 12

350 355.6 520 30 82 438 4 M24 16 26 470 390 16 12
400 406.4 580 32 85 490 4 M27 16 30 525 445 16 12
500 508 715 34 90 610 4 M30 20 33 650 548 16 12
600 609.6 840 36 95 725 5 M33 20 36 770 652 18 12
700 711.2 910 36 100 795 5 M33 24 36 840 755 18 12

800 812.8 1 38 105 900 5 M36 24 39 950 855 20 12
025
900 914.4 1 40 110 1 000 5 M36 28 39 1 050 955 20 12
125
1 000 1 016 1 42 120 1 115 5 M39 28 42 1 170 1 058 22 16
255
1 200 1 220 1 48 130 1 330 5 M45 32 48 1 390 1 262 30 16
485
1 400 1 420 1 52 145 1 530 5 M45 36 48 1 590 1 465 30 16

685
1 600 1 620 1 58 160 1 750 5 M52 40 56 1 820 1 668 35 16
930
1 800 1 820 2 62 170 1 950 5 M52 44 56 2 020 1 870 35 16
130
2 000 2 020 2 66 180 2 150 5 M56 48 62 2 230 2 072 40 16
345
24
IS 6392 : 2020


Ød1
Ød 2
f
b
Ød4
Øk
ØD

Size TABLE 18 SCREWED BOSS FLANGES
o.d. D Bore b d4 f No. d2 k
d1 Dia. Ød1
10 17.2 90 18.0 14 40 2 M12 4 14 60

15 21.3 95 22.0 14 45 2 M12 4 14 65
20 26.9 105 27.5 16 58 2 M12 1 IN 6.25
TAPER 4 14 75
25 33.7 115 34.5 16 68 2 ON DIAMETER
M12 4 14 85
32 42.4 140 43.5 16 78 2 M16 4 18 100
Ød2
40 48.3 150 49.5 16 88 3 M16 h 4 18 110
50 60.3 165 61.5 18 102 3 M16 b 4 18 125
65 76.1 185 77.5 18 122 3 M16 4 18 145
80 88.9 200 90.5 20Ød3 138 3 f
M16 8 18 160
100 114.3 220 116.0 20 Ød4
158 3 M16 8 18 180
Øk
125 139.7 250 141.5 22 ØD
188 3 M16 8 18 210
150 168.3 285 170.5 22 212 3 M20 8 22 240
175 193.7 315 195.5 24 242 3 M20 8 22 270
200 219.1 340 221.5 24 268 3 M20 12 22 295
250 273 405 276.5 26 320 3 M24 12 26 355
Ød1
300 323.9 460 327.5 28 378 4 M24 12 26 410
350 355.6 520 359.5 32 438 4 M24 16 26 470
400 406.4 580 411.0 36 490 4 M27 16 30 525
500 508 715 513.5 44 610 4 M30
TAPER 1 IN 20
6.25 33 650
600 609.6 840 616.5 52 725 5 M33
ON DIAMETER20 36 770
700 711.2 910 58 795 5 M33 24 36 840

As agreed between
Ød2
the purchaser and
the manufacturer.
800 812.8 1 025 64 900 5 M36 h 24 39 950

900 914.4 1 125 72 1 000 5 M36 b 28 39 1 050
1 000 1 016 1 255 78 1 115 5 M39 28 42 1 170
1 200 1 220 1 485 Ød
94 3 1 330 5 M45
f 32 48 1 390
Ød4
Øk
25
ØD
Ød 2
f
b
IS 6392 : 2020
Ød4
Øk
ØD
Nominal pressure 1 and 1.6 N/mm2.

Ød1
TAPER 1 IN 6.25
ON DIAMETER
Ød2
h
b
Ød3 f
Ød4
Øk
ØD

Nom Pipe Flange Raised Face Bolting Drilling BOSS
Size
Ød1
o.d. D b h d4 f No. d2 k d3
d1
≈
TAPER 1 IN 6.25
6 10.2 75 12 18 32 2 M10 4
ON DIAMETER 11 50 20
8 13.5 80 12 18 38 2 M10 4 11 55 25
10 17.2 90 Ød14
2
20 40 2 M12 4 14 60 30
15 21.3 95 14 20 45 2 M12 4 h 14 65 35
20 26.9 105 16 24 58 2 M12 4
b 14 75 45
Ød3 f
25 33.7 115 16 24 68 Ød42 M12 4 14 85 52
32 42.4 140 16 26 Øk
78 2 M16 4 18 100 60
40 48.3 150 16 26 88 ØD3 M16 4 18 110 70
50 60.3 165 18 28 102 3 M16 4 18 125 85
65 76.1 185 18 32 122 3 M16 4 18 145 105
80 88.9 200 20 34 138 3 M16 8 18 160 118

100 114.3 220 20 40 158 3 M16 8 18 180 140
125 139.7 250 22 44 188 3 M16 8 18 210 168
150 165.1 285 22 44 212 3 M20 8 22 240 195
26
ON DIAMETER
Ød2
h
b IS 6392 : 2020
Ød3 f
Table 19 Slip-on Boss
Ød Flanges for Welding
4
(Øk
Clauses 5.1 and 6.1 )
ØD
NOTE — Use table also for nominal size 6 to 65 mm for 1.0 N/mm2 nominal pressure.
Ød1
TAPER 1 IN 6.25
ON DIAMETER
Ød2
h
b
Ød3 f
Ød4
Øk
ØD

d1 Dia.
≈
6 10.2 75 11.5 12 18 32 2 M10 4 11 50 20

8 13.5 80 15.0 12 18 38 2 M10 4 11 55 25
10 17.2 90 18.0 14 20 40 2 M12 4 14 60 30
10 21.3 95 22.0 14 20 45 2 M12 4 14 65 35
20 26.9 105 27.5 16 24 58 2 M12 4 14 75 45
25 33.7 115 34.5 16 24 68 2 M12 4 14 85 52

32 42.4 140 43.5 16 26 78 2 M16 4 18 100 60
40 48.3 150 49.5 16 26 88 3 M16 4 18 110 70
50 60.3 165 61.5 18 28 102 3 M16 4 18 125 85
65 76.1 185 77.5 18 32 122 3 M16 4 18 145 105
80 88.9 200 90.5 20 34 138 3 M16 8 18 160 118

100 114.3 220 116.0 20 40 158 3 M16 8 18 180 140
125 139.7 250 141.5 22 44 188 3 M16 8 18 210 168
150 168.3 285 170.5 22 44 212 3 M20 8 22 240 195
200 219.1 340 221.5 24 44 268 3 M20 8 22 295 247
250 273 405 276.5 26 46 320 3 M24 12 26 355 300

300 323.9 460 327.5 28 46 378 4 M24 12 26 410 355
27
IS 6392 : 2020


NOTE — The two types of flanges shown are alternatives at the option the manufacturer.
b
Ød2
Øk
ØD
FORM A
2 APPROX
Ød2
Ød9
Øk
ØD
FORM B
Flange Spigot Drilling

Nom Size Bolting
D b d9 No. d2 k
10 90 14 - M12 4 14 60
15 95 14 - M12 4 14 65
20 105 16 - M12 4 14 75
25 115 16 - M12 4 14 85
32 140 16 - M16 4 18 100
Ød2 r
40 150 16 - M16 4 18 110
50 165 18 - M16 4
f
b 18 125
65 185 18 55 M16 4 18 145
80 200 20 Ød70
3 M16 8 18 160
100 220 20 90 Ød4 M16 8 18 180
Øk
ØD
125 250 22 115 M16 8 18 210
150 285 22 140 M20 8 22 240
175 315 24 165 M20 8 22 270
200 340 24 190 M20 12 22 295
250 405 TABLE
26 22 WELDING
237 NECK FLANGES
M24 12 26 355
300 460 28 285 M24 12 26 410

350 520 30 332 M24 16 26 470
400 580 32 380 M27 16 30 525
500 715 36 475 M30 20 33 650
Ød1 h2
f
Ød2 28 r
h1
b
Ød3
Ød4
Øk
FORM A
2 APPROX
Ød2
b IS 6392 : 2020
Ød9 21 Integral Flanges

Table
Øk
Clauses 5.1 and 6.1 )
(ØD
FORM B
TABLE
NOTE 21nominal
— For INTEGRAL
sizes 10FLANGES
to 150 mm, use Table 26.
Ød2 r
f
b
Ød3
Ød4
Øk
ØD
Nom Flange Raised Face Drilling Neck

Bolting
Size D b TABLE
d 22 WELDING
f NECK FLANGES
No. d2 k d3 r
4
175 330 28 248 3 M24 12 26 280 217 8

200 360 30 278 3 M24 12 26 310 246 8
250 425 32 335 3 M27 12 30 370 298 10
300 485 34 395 4 M27 16 30 430 352 10
350 555 38 450 4 M30 16 33 490 408 10
Ød1 h2
400 620 40 505 4 M33 16 36 f 550 460 10

Ød2 r
500 730 44 615 4 M33 20 36 h1
660 566 12
600 845 46 720 5 M36 20 39 b 770 670 12
700 960 50 820 5 M39 24 42 875 776 12
Ød3
800 1 085 54 930 5 M45 24 48 990 882 15
Ød4
Øk
900 1 185 58 1 030 5 M45
ØD 28 48 1 090 988 15
1 000 1 320 62 1 140 5 M52 28 56 1 210 1 094 18
1 200 1 550 70 1 350 5 M52 32 56 1 420 1 306 18
1 400 1 755 76 1 560 5 M56 36 62 1 640 1 514 18
1 600 1 975 84 1 780 5 M56 40 62 1 860 1 726 20
1 800 2 195 90 1 985 5 M64 44 70 2070 1 936 20

2000 2 425 96 2 210 5 M64 48 70 2 300 2 144 20
29
Ød2 r
f
b
IS 6392 : 2020
Ød3
Table 22 Welding
Ød Neck Flanges
4
( Clauses
Øk 5.1 and 6.1 )
ØD

Ød1 h2
f
Ød2 r
h1
b
Ød3
Ød4
Øk
ØD

d1 ≈
175 193.7 330 28 75 248 3 M24 12 26 280 218 15 10

200 219.1 360 30 80 278 3 M24 12 26 310 244 16 10
250 273 425 32 88 335 3 M27 12 30 370 298 18 12
300 323.9 485 34 92 395 4 M27 16 30 430 352 18 12

350 355.6 555 38 100 450 4 M30 16 33 490 398 20 12
400 406.4 620 40 110 505 4 M33 16 36 550 452 20 12

500 508 730 44 125 615 4 M33 20 36 660 558 20 12
600 609.6 845 46 125 720 5 M36 20 38 770 660 20 12
700 711.2 960 46 125 820 5 M39 24 42 875 760 20 12
800 812.8 1 085 50 135 930 5 M45 24 48 990 865 22 12
900 914.4 1 185 54 145 1 030 5 M45 28 48 1 090 968 24 12

1 000 1 016 1 320 58 155 1 140 5 M52 28 56 1 210 1 070 24 16
30
IS 6392 : 2020



Ød1
Ød2
f
b
Ød4
Øk
ØD

Ød1
Dia.
TAPER 1 IN 6.25
d1
ON DIAMETER
175 193.7 330 195.5 26 248 3 M24 12 26 280

Ød 2
200 219.1 360 221.5 28 278 3 M24 12 h 26 310
b
250 273 425 276.5 32 335 3 M27 12 30 370
Ød3 f
300 323.9 485 327.5 38 Ød4
395 4 M27 16 30 430
Øk
350 355.6 555 359.5 42 450 4 M30 16 33 490
ØD
400 406.4 620 411.0 46 505 4 M33 16 36 550

500 508 730 513.5 58 615 4 M33 20 36 660
Ød2
600 609.6 845 616.5 66 720 5 M36 20 39 770

b
Øk
ØD
FORM A
Ød2
2 APPROX
b
31
Ød9
Øk
ØD
FORM B
Ød2
f
IS 6392 : 2020 b
Ød4 Boss Flanges for Welding

Table 24 Slip-on
Øk
ØD

Ød1
TAPER 1 IN 6.25
ON DIAMETER
Ød 2
h
b
Ød3 f
Ød4
Øk
ØD

Size TABLE 25 PLATE BLACK FLANGES
o.d. D Bore b h d4 f NO. d2 k d3
d1 Dia.
Ød2
≈
b
6 10.2 75 11.5 14 20 32 2 M10 4 11 50 20
8 13.5 80 15.0 14 20 Øk 38 2 M10 4 11 55 25
10 17.2 90 18.0 16 22 40
ØD 2 M12 4 14 60 30
15 21.3 95 22.0 16 22 FORM45A 2 M12 4 14 65 35
20 26.9 105 27.5 18 26 58 2 M12 4 14 75 45
Ød2
25 33.7 115 34.5 18 28 68 2 M12 4 14 85 52
2 APPROX
32 42.5 140 43.5 18 30 78 2 bM16 4 18 100 60
40 48.3 150 49.5 18 32 88 3 M16 4 18 110 70
Ød9
50 60.3 165 61.5 20 34 102 3 M16 4 18 125 85
Øk
65 76.1 185 77.5 22 38 ØD 122 3 M16 8 18 145 105
FORM B
80 88.9 200 90.5 24 40 138 3 M16 8 18 160 118
100 114.3 235 116.0 24 44 162 3 M20 8 22 190 145
125 139.7 270 141.5 26 48 188 3 M24 8 26 220 170
150 168.3 300 170.5 28 52 218 3 M24 8 26 250 200
200 219.1 360 221.5 32 52 278 3 M24 12 26 310 256
250 273 425 276.5 40 60 335 3 M27 12 30 370 310

300 323.9 485 327.5 48 67 395 4 M27 16 30 430 364
32
Ød 2
h
IS 6392 : 2020
b
(Ød
Clauses
3 5.1 and 6.1 ) f
Ød4
Øk pressure 2.5 N/mm2.
Nominal
ØD
NOTES:
1 The two types of flanges shown are alternatives at the option the manufacturer.
2 For nominal sizes 10 to 150 mm, use Table 31.
Ød2
Øk
ØD
FORM A
Ød2
2 APPROX
b
Ød9
Øk
ØD
FORM B
Nom Size Flange Spigot Bolting Drilling

D b d9 No. d2 k
175 330 28 165 M24 12 26 280

200 360 30 190 M24 12 26 310
250 425 32 237 M27 12 30 370
300 485 34 285 M27 16 30 430
350 555 38 332 M30 16 33 490
400 620 40 380 M33 16 36 550

500 730 45 475 M33 20 36 660
33
IS 6392 : 2020
Table 26 Integral Flanges


NOTE — This table shall be used in case of following sizes and pressures:
Nominal Size Pressure Size

mm N/mm2
10 to 50 1.6
10 to 150 2.5
80 to 150 2.5
Ød2 r
f
b
Ød3
Ød4
Øk
ØD

Bolting
10 90 16 40 2 M12 4 14 60 30 4
15 95 16 45 2 M12 4 14 65 37 4
20 105 18 58 2 M12 4 14 75 44 5
25 115 18 68 2 Ød1 M12 4 14
h 85 53 5
2
32 140 18 78 2 M16 4 18 100 60 5
f
r
40 150 18Ød2 88 3 M16 4 18 h110 68 5
1
50 165 20 102 3 M16 4 18 125 80 5
b
65 185 22 122 3 M16 8 18 145 99 6
80 200 24 138 3Ød3 M16 8 18 160 116 6
100 235 24 162 3 Ød
M20
4 8 22 190 136 6
Øk
ØD

Ød1
34
Ød2
f b
IS 6392 : 2020

Bolting
125 270 26 188 3 M24 8 26 220 165 8
150 300 28 218 3 M24 8 26 250 192 8
175 350 32 260 3 M27 12 30 295 223 10
200 375 34 285 3 M27 12 30 320 252 10
250 450 38 345 3 M30 12 33 385 308 10
300 515 42 410 4 M30 16 33 450 364 12

350 580 46 465 4 M33 16 36 510 420 12
400 660 50 535 4 M36 16 39 585 476 12
500 755 52 615 4 M39 20 42 670 578 15
600 890 60 735 5 M45 20 48 795 690 15
700 995 64 840 5 M45 24 48 900 796 18

800 1 140 72 960 5 M52 24 56 1 030 908 18
900 1 250 76 1 070 5 M52 28 56 1 140 1 014 18
1 000 1 360 80 1 180 5 M52 28 56 1 250 1 120 20
1 200 1 575 88 1 380 5 M56 32 62 1 460 1 332 20
1 400 1 795 98 1 600 5 M56 36 62 1 680 1 548 20

1 600 2 025 108 1 815 5 M64 40 70 1 900 1 762 20
35
Ød2 r
IS 6392 : 2020 f
b
Ød3 5.1 and 6.1 )
( Clauses
Ød4
Øk
ØD
NOTE — Also for nominal sizes 10 to 150 mm and 2.5 N/mm2 nominal pressure, use this table.
Ød1 h2
f
Ød2 r
h1
b
Ød3
Ød4
Øk
ØD
Nom Pipe Flange TABLE 28 PLATE

Raised Face FLANGES
Bolting FOR WELDING
Drilling Neck
Size D b h1 d4 f No. d2 k d3 h2 r
o.d. Ød1
d1 ≈
10 17.2 90 16 35 40 2 M12 4 14 60 28 6 4
15 21.3 95 Ød
16 2 38 45 2 M12 4 14 65 32 6 4
20 26.9 105 18 40 58 2 M12 4 14 75 40 6 4
25 33.7 115 18 40 68 2 M12 4 14 85 46 f 6b 4
32 42.4 140 18 42 78 2 M16 4 18 100 56 6 6
Ød4
40 48.3 150 18 45 88 3 M16 4 18 110 64 7 6
Øk
50 60.3 165 20 48 102 3 M16 4 18 125 75 8 6
65 76.1 185 22 52 122 3 ØD M16 8 18 145 90 10 6
80 88.9 200 24 58 138 3 M16 8 18 160 105 12 8
100 114.3 235 24 65 162 3 M20 8 22 190 134 12 8
125 139.7 270 26 68 188 3 M24 8 26 220 162 12 8

150 168.3 300 28 75 218 3 M24 8 26 250 192 12 10
175 193.7 350 32 82 260 3 M27 12 30 295 218 15 10
200 219.1 375 34 88 285 3 M27 12 30 320 244 16 10
250 273 450 38 105 345 3 M30 12 33 385 306 18 12
300 323.9 515 42 115 410 4 M30 16 33 450 362 18 12

350 355.6 580 46 125 465 4 M33 16 36 510 408 20 12
400 406.4 660 50 135 535 4 M36 16 39 585 462 20 12
500 508 755 52 140 615 4 M39 20 42 670 562 20 12
36
Ød1 h2
f
ØdANDHRA
UREAU UNDER THE LICENSE FROM BIS FOR r
PRADESH POWER GENERATION CORPORATION LTD. - VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.2
2 h1 IS 6392 : 2020
b
Ød3
( Clauses
Ød4 5.1 and 6.1 )
Øk
ØD
NOTE — Also for nominal sizes 10 to 150 mm and 2.5 N/mm2 pressure, use this table.
Ød1
Ød2
f b
Ød4
Øk
ØD

Size D Bore b d4 f No. d2 k
o.d.
d1 Dia.
10 17.2 90 18.0 16 40 2 M12 4 14 60

15 21.3 95 22.0 16 45 2 M12 4 14 65
20 26.9 105 27.5 18 58 2 M12 4 14 75
25 33.7 115 34.5 18 68 2 M12 4 14 85
32 42.4 140 43.5 18 78 2 M16 4 18 100
40 48.3 150 49.5 20 88 3 M16 4 18 110

50 60.3 165 61.5 20 102 3 M16 4 18 125
65 76.1 185 77.5 22 122 3 M16 8 18 145
80 88.9 200 90.5 24 138 3 M16 8 18 160
100 114.3 235 116.0 26 162 3 M20 8 22 190
125 139.7 270 141.5 28 188 3 M24 8 26 220

150 168.3 300 170.5 30 218 3 M24 8 26 250
175 193.7 350 195.5 32 260 3 M27 12 30 295
200 219.1 375 221.5 34 285 3 M27 12 30 320
250 273 450 276.5 42 345 3 M30 12 33 385
300 323.9 515 327.5 50 410 4 M30 16 33 450

350 355.6 580 359.5 56 465 4 M33 16 36 510
400 406.4 660 411.0 64 535 4 M36 16 39 585
500 508 755 513.5 72 615 4 M39 20 42 670
37
IS 6392 : 2020

Nominal pressure 2.5 and 4.0 N/mm2.

Ød1
TAPER 1 IN 6.25
ON DIAMETER
Ød2
h
b
Ød3 f
Ød4
Øk
ØD

Size o.d. D b h Ø
d d1 f No. d2 k d3
4
d1
≈ TAPER 1 IN 6.25
ON DIAMETER
6 10.2
Ød 75 14 20 32 2 M10 4 11 50 20
2
8 13.5 80 14 20 38 2 M10 4 h
11 55 25
10 17.2 90 16 22 40 2 M12 4 b 14 60 30
15 21.3 95 16 22 Ø d3 45 2 M12 4 14 65 35
f
20 26.9 105 18 26 58 Ø d4 2 M12 4 14 75 45
Øk
25 33.7 115 18 28 68 D
Ø 2 M12 4 14 85 52
32 42.4 140 18 30 78 2 M16 4 18 100 60
40 48.3 150 18 32 88 3 M16 4 18 110 70
50 60.3 165 TABLE3431
20 PLATE
102 BLACK
3 FLANGES
M16 4 18 125 85
65 76.1 Ød
1852 22 38 122 3 M16 8 18 145 105
80 88.9 200 24 40 138 3 M16 b 8 18 160 118

100 114.3 235 24 44 162 3 M20 8 22 190 145
125 139.7 270 26 48 Øk
188 3 M24 8 26 220 170
150 165.1 300 28 52 218 ØD 3 M24 8 26 250 200
FORM A
Ød2
38 b
Ød9
Øk
ØD
2 APPROX
FORM B
h
b
Ød3
f IS 6392 : 2020
Ød4
Table 30 Slip-on
Øk Boss Flanges for Welding
ØD

TABLE 30 SLIP-ONAll
BOSS FLANGES
dimensions FOR WELDING
in millimeters.
Ø d1
TAPER 1 IN 6.25
ON DIAMETER
Ø d2
h
b
Ø d3
f
Ø d4
Øk
ØD

Nom Pipe Ød2 Flange Raised Face Bolting Drilling BOSS
d1 Dia. b
≈
Øk
6 10.2 75 11.5 14 20 32
ØD 2 M10 4 11 50 20
8 13.5 80 15.0 14 20 38 2 M10 4 11 55 25
FORM A
10 17.2 90 18.0 16 22 40 2 M12 4 14 60 30
15 21.3 Ød2
95 22.0 16 22 45 2 M12 4 14 65 35
20 26.9 105 27.5 18 26 58 2 M12 4 14 75 45
b
25 33.7 115 34.5 18 28 68 2 M12 4 14 85 52
32 42.4 140 43.5 18 30 78 2 M16 4 18 100 60
Ød9
40 48.3 150 49.5 18 32 88
Øk 3 M16 4 18 110 70
50 60.3 165 61.5 20 34 ØD102 3 M16 4 18 125 85
65 76.1 185 77.5 22 38 122 3 2 APPROX
M16 8 18 145 105
FORM B
80 88.9 200 90.5 24 40 138 3 M16 8 18 160 118

100 114.3 235 116.0 24 44 162 3 M20 8 22 190 145
125 139.7 270 141.5 26 48 188 3 M24 8 26 220 170
150 168.3 300 170.5 28 52 218 3 M24 8 26 250 200
200 219.1 375 221.5 32 52 285 3 M27 12 30 320 260
250 273 450 276.5 40 60 345 3 M30 12 33 385 320

300 323.9 515 327.5 48 67 410 4 M30 16 33 450 380
39
Ø d1
TAPER 1 IN 6.25
IS 6392 : 2020 ON DIAMETER
Ø d2
Table 31 Plate Black Flanges h
( Clauses 5.1 and 6.1 ) b
Ø d3
Nominal pressure 4.0 f
Ø N/mm
d4 .
2

Øk
NOTES ØD
1 The two types of flanges shown are alternatives at the option of manufacturer.
2 Also for nominal sizes 10 to 150 mm and 2.5 N/mm2 nominal pressure, use this table.
Ød2
Øk
ØD
FORM A
Ød2
Ød9
Øk
ØD
2 APPROX
FORM B

Size
D b D9 No. d2 k
10 90 16 - M12 4 14 60
15 95 16 - M12 4 14 65
20 105 18 - M12 4 14 75
25 115 18 - M12 4 14 85
32 140 18 - M16 4 18 100
40 150 18 - M16 4 18 110

50 165 20 - M16 4 18 125
65 185 22 55 M16 8 18 145
80 200 24 70 M16 8 18 160
100 235 24 90 M20 8 22 190
40
IS 6392 : 2020

Size
D b D9 No. d2 k
125 270 26 115 M24 8 26 220
150 300 28 140 M24 8 26 250
175 350 32 165 M27 12 30 295
200 375 34 190 M27 12 30 320
250 450 38 237 M30 12 33 385
300 515 42 285 M30 16 33 450

350 580 46 332 M33 16 36 510
400 660 50 380 M36 16 39 585
500 755 56 475 M39 20 42 670
41
IS 6392 : 2020



Ød2 r
f
b
Ød3
Ød4
Øk
ØD

Bolting
50 180 26 102 3 M20 4 22 135 90 5

65 205 26 122 3 M20 8 22 160 105 5
80 215 28 138 3 M20 8 22 170 122 5
100 250 30 162 3 M24 8 26 200
h 146 5
Ød1 2
125 295 34 188 3 M27 8 30 240 177 6
150 345 36 218 3 M30 8 33 280 204 6

Ød2 r f h1
175 375 40 260 3 M30 12 33 310 235 8
200 415 42 285 3 M33 12 36 345 264 8
b
250 470 46 465 3 M33 12 36 400 320 8
300 530 52 410 4 M33 16 36 460 378 10
Ød3
Ød4
350 600 56 465 4 M36 16 39 525 434 10
Øk
400 670 60 535 4 M39 16 42 585 490 12
500 800 68 615 4 ØD M45 20 48 705 602 12
600 930 76 735 4 M52 20 56 820 714 15
700 1 045 84 840 4 M52 24 56 935 826 15

800 1 165 92 960 4 M56 24 62 1 050 938 18
900 1 285 98 1 070 4 Ød1 M56 28 62 1 170 1 048 18
1 000 1 415 108 1 180 4 M64 28 70 1 290 1 162 18
1 200 1 665 126
Ød 1 380 4 M72 32 78 1 530 1 390 18
2
f
b
42
Ød4
Øk
ØD
Ød2 r
UREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER GENERATION CORPORATION LTD. - VIJAYAWADA
f ON 9/22/2021 1:09:09 PM (172.2
b IS 6392 : 2020
Table Ød
33 3Welding Neck Flanges
( Clauses 4 and 6.1 )
Ød5.1
Øk
ØD 6.4 N/mm2.
Nominal pressure
TABLE 33For
NOTE — WELDING NECK
nominal sizes FLANGES
10 to 40 mm, use Table 37.
Ød1 h2
Ød2 r f h1
Ød3
Ød4
Øk
ØD

Nom PIPE FLANGE RAISED FACE

Ød BOLTING DRILLING NECK
1
d1 ≈
Ød2
50 60.3 180 26 62 102 3 M20 4 22 135 f 82 10 6

b
65 76.1 205 26 68 122 3 M20 8 22 160 98 12 6
80 88.9 215 28 72 138 3 M20 8 22 170 112 12 8
Ød4
100 114.3 250 30 78 162 3 Øk M24 8 26 200 138 12 8
125 139.7 295 34 88 188 ØD 3 M27 8 30 240 168 12 8
150 168.3 345 36 95 218 3 M30 8 33 280 202 12 10

175 193.7 375 40 105 260 3 M30 12 33 310 228 16 10
200 219.1 415 42 110 285 3 M33 12 36 345 256 16 10
250 273 470 46 125 345 3 M33 12 36 400 316 18 12
300 323.9 530 52 140 410 4 M33 16 36 460 372 18 12
350 355.6 600 56 150 465 4 M36 16 39 525 420 20 12

400 406.4 670 60 160 535 4 M39 16 42 585 475 20 12
43
Ød2 r f h1
b
IS 6392 : 2020
Ød3
Ød
Øk
Nominal pressure
ØD 6.4 N/mm .
2

Ød1
Ød2
f
b
Ød4
Øk
ØD

Size o.d. D BORE b d4 f No. d2 k
d1 Dia.
50 60.3 180 61.5 26 102 3 M20 4 22 135

65 76.1 205 77.5 26 122 3 M20 8 22 160
80 88.9 215 90.5 30 138 3 M20 8 22 170
100 114.3 250 116.0 32 162 3 M24 8 26 200
125 139.7 295 141.5 34 188 3 M27 8 30 240
150 168.3 345 170.5 36 218 3 M30 8 33 280

175 193.7 375 195.5 40 260 3 M30 12 33 310
200 219.1 415 221.5 46 285 3 M33 12 36 345
250 273 470 276.5 54 345 3 M33 12 36 400
300 323.9 530 327.5 62 410 4 M33 16 36 460
350 355.8 600 359.5 72 465 4 M36 16 39 525

400 406.4 670 411.0 78 535 4 M39 16 42 585
44
IS 6392 : 2020


NOTE
TABLE 35 — For nominal
SCREWED BOSS sizesFLANGES
10 to 40 mm, use Table 39.
Ød5
Ød1 FOR SEAL WELDING
IF NECESSARY
TAPER 1 IN 6.25
P ON DIAMETER
Ød2
h
b
Ød3 f
Ød4
Øk
ØD
TABLE 36 INTERGAL FLANGES

Size o.d. D b h d4 f No. d2 k d3 p r
d1
≈
Ød 2 r
50 60.3 180 26 36 102 3 M20 4 22 135 90 7 3
f
65 76.1 205 26 40 122 3 M20 8 22 160 112 b 7 3
80 88.9 215 28 44 138 3 M20 8 22 170 125 7 3
100 114.3 250 30 52 162 3
Ød3 M24 8 26 200 152 7 3
Ød4
125 139.7 295 34 56 188 3 M27 8 30 240 185 7 3
Øk
ØD
150 165.1 345 36 60 218 3 M30 8 33 280 215 7 3
Ød1 h2
Ød 2 r f h1
45
Ød3
Ød4
Øk
ØD
TAPER 1 IN 6.25
P ON DIAMETER
2Ød
IS 6392 : 2020 h
b
Ød3 ( Clauses 5.1 and 6.1 ) f
Ød4
Øk
ØD
TABLE 36 INTERGAL FLANGES
Ød 2 r
f
b
Ød3
Ød4
Øk
ØD
Nom Flange Raised Face Bolting DRILLILG Neck

Size
D b d4 f No. d2 k d3 r
125 315 40 188 3 M30 8 33 250 185 6

150 355 44 218 3 M30 12 33 290 216 6
Ød1 h2
175 385 48 260 3 M30 12 33 320 247 8
200 430 52 285 3 M33 12 36 360 278 8
250 505 60 345 3 M36 12 39 430 340 8
Ød 2 r f h1
300 585 68 410 4 M39 16 42 500 402 10
350 655 74 465 4 M45 16 48 560 b 460 10
400 715 78 535 4 M45 16 48 620 518 12
500 870 94 615 4 Ød3M52 20 56 760 630 15
600 990 104 735 4 M56 Ød4 20 62 875 740 15
Øk
700 1 145 120 840 4 M64 24 70 1 020 860 18
ØD
46
ØdANDHRA
UREAU UNDER THE LICENSE FROM BIS FOR 2 r
PRADESH POWER GENERATION CORPORATION LTD. - VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.2
IS 6392 : 2020
f
b
Ød3
Ød4
Øk
ØD
NOTE — Also for nominal sizes 10 to 40 mm and 6.4 N/mm2 nominal pressure, use this table.
Ød1 h2
Ød 2 r f h1
Ød3
Ød4
Øk
ØD

d1 ≈
10 17.2 100 20 45 40 2 M12 4 14 70 32 6 4

15 21.3 105 20 45 45 2 M12 4 14 75 34 6 4
20 26.9 130 22 58 58 2 M16 4 18 90 42 8 4
25 33.7 140 24 58 68 2 M16 4 18 100 52 8 4
32 42.4 155 24 60 78 2 M20 4 22 110 62 8 6
40 48.3 170 26 62 88 3 M20 4 22 125 70 10 6

50 60.3 195 28 68 102 3 M24 4 26 145 90 10 6
65 76.1 220 30 76 122 3 M24 8 26 170 108 12 6
80 88.9 230 32 78 138 3 M24 8 26 180 120 12 8
100 114.3 265 36 90 162 3 M27 8 30 210 150 12 8
47
IS 6392 : 2020

d1 ≈
125 139.7 315 40 105 188 3 M30 8 33 250 180 12 8
150 168.3 355 44 115 218 3 M30 12 33 290 210 12 10
175 193.7 385 48 127 260 3 M30 12 33 320 245 16 10
200 219.1 430 52 130 285 3 M33 12 36 360 278 16 10
250 273 505 60 157 345 3 M36 12 39 430 340 18 12
300 323.9 585 68 170 410 4 M39 16 42 500 400 18 12

350 355.6 655 74 189 465 4 M45 16 48 560 460 20 12
48
IS 6392 : 2020


NOTE — Also for nominal sizes 10 to 40 mm and 6.4 N/ mm2 nominal pressure, use this table.
Ød1
Ød2
f
b
Ød4
Øk
ØD

Size D Bore b Ød5 d4 f No. d2 k
o.d.
d1 Dia. Ød1 FOR SEAL WELDING
IF NECESSARY
10 17.2 100 D 18.0 20 40 2 M12 TAPER 41 IN 6.25 14 70
15 21.3 105 22.0 20 45 P 2 M12
ON DIAMETER
4 14 75
20 26.9 130 27.5 22 58 2 M16 4 18 90
Ød2 r
25 33.7 140 34.5 24 68 2 M16 4 18 100
32 42.4 155 43.5 24 78 2 M20 4 h 22 110
b
40 48.3 170 49.5 26 88 3 M20 4 22 125
50 60.3 195 61.5 Ød3
28 102 3 M24 f 4 26 145
65 76.1 220 77.5 30 1224
Ød 3 M24 8 26 170
80 88.9 230 90.5 34
Øk 138 3 M24 8 26 180
100 114.3 265 116.0 36 162 3 M27 8 30 210
ØD
125 139.7 315 141.5 42 188 3 M30 8 33 250

150 168.3 355 170.5 48 218 3 M30 12 33 290
175 193.3 385 195.5 54 260 3 M30 12 33 320
200 219.1 430 221.5 60 285 3 M33 12 36 360
250 273 505 276.5 72 345 3 M36 12 39 430
300 223.9 585 327.5 84 410 4 M39 16 42 500
350 355.6 655 359.5 95 465 4 M45 16 48 560
400 406.4 715 411.0 106 535 4 M45 16 48 620
500 508 870 513.5 128 615 4 M52 20 56 760
Ød2 r
49 f
b
Ød3
Ød4
Øk
ØD
Ød2
f
b
IS 6392 : 2020 Ød4
Øk
Table 39ØD
Screwed Boss Flanges

All dimensions
TABLE 39 SCREWED BOSSin millimeters.
FLANGES
Ød5
Ød1 FOR SEAL WELDING
IF NECESSARY
D TAPER 1 IN 6.25
P ON DIAMETER
Ød2 r
h
b
Ød3 f
Ød4
Øk
ØD

Size o.d. D b h d4 f No. d2 k d3 p r
d1
≈
10 17.2 100 20 28 40 2 M12 4 14 70 40 4 2

15 21.3 105 20 28 45 2 M12 4 14 75 43 6 2
20 26.9 130 22 30 58 2 M16 4 18 90 52 7 2
25 33.7 140 24 32 68 2 M16 4 18 100 60 7 3
32 42.4 155Ød2 24 32 78 2 M20 r4 22 110 68 7 3
40 48.3 170 26 34 88 3 M20 4 22

f
125 b 80 7 3
50 60.3 195 28 36 102 3 M24 4 26 145 95 7 3
65 76.1 220 30 40 Ød3
122 3 M24 8 26 170 118 7 3
80 88.9 230 32 44 138 Ød
3 4 M24 8 26 180 130 7 3
100 114.3 265 36 52 Øk
162 3 M27 8 30 210 158 7 3
ØD
125 139.7 315 40 56 188 3 M30 8 33 250 188 7 3
150 165.1 355 44 60 218 3 M30 12 33 290 225 7 3
50
Ød1
IF NECESSARY
D TAPER 1 IN 6.25
P ON DIAMETER
Ød2 r IS 6392 : 2020
h
Table 40 Integral Flanges b
Ød3 f
Nominal pressure
Ød16.0 N/mm2.
4
All dimensions
Øk in millimeters.
ØD
NOTE — This table shall also be used in this case of following sizes and pressures:
Nominal Size Nominal Pressure

mm N/mm2
10 to 40 6.4 to 10.0
50 to 100 10.0
Ød2 r
f
b
Ød3
Ød4
Øk
ØD
Nom Flange Raised Face Bolting Drilling Neck

10 100 20 40 2 M12 4 14 70 40 4
15 105 20 45 2 M12 4 14 75 45 4
20 130 22 58 2 M16 4 18 90 50 4
25 140 24 68 2 M16 4 18 100 61 4
32 155 26 78 2 M20 4 22 110 68 4
40 170 28 88 3 M20 4 22 125 82 4

50 195 30 102 3 M24 4 26 145 96 4
65 220 34 122 3 M24 8 26 170 118 5
80 230 36 138 3 M24 8 26 180 128 5
100 265 40 162 3 M27 8 30 210 150 5
125 315 44 188 3 M30 8 33 250 184 6

150 355 50 218 3 M30 12 33 290 224 6
175 390 54 260 3 M33 12 36 320 250 8
200 430 60 285 3 M33 12 36 360 288 8
250 515 68 345 3 M39 12 42 430 346 8
300 585 78 410 4 M39 16 42 500 414 10
51
IS 6392 : 2020


Ød1 h2
Ød2 r f h1
Ød3
Ød4
Øk
ØD
Nom Pipe TABLE 42 PLATE

Flange Raised FLANGES
Face FOR WELDINGDrilling
Bolting Neck
Size o.d. D B h1 d4 Ødf1 No. d2 k d3 h2 r
d1
10 17.2 100 20 45 40 2 M12 4 14 70 32 6 4

Ød2
15 21.3 105 20 45 45 2 M12 4 14 75 34 6 4
20 26.9 130 22 58 58 2 M16 4 18 90 f 42 8 4
b
25 33.7 140 24 58 68 2 M16 4 18 100 52 8 4
32 42.4 155 26 60 78 2 M20 4 22 110 55 8 6
Ød4
Øk
40 48.3 170 28 64 88 ØD 3 M20 4 22 125 70 10 6
50 60.3 195 30 75 102 3 M24 4 26 145 90 10 6
65 76.1 220 34 82 122 3 M24 8 26 170 108 12 6
80 88.9 230 36 86 138 3 M24 8 26 180 120 12 8
100 114.3 265 40 100 162 3 M27 8 30 210 150 12 8
52
IS 6392 : 2020

Size o.d. D B h1 d4 f No. d2 k d3 h2 r
d1
125 139.7 315 44 115 188 3 M30 8 33 250 180 14 8
150 168.3 355 50 128 218 3 M30 12 33 290 210 14 10
175 193.7 390 54 138 260 3 M33 12 36 320 245 16 10
200 219.1 430 60 140 285 3 M33 12 36 360 278 16 10
250 273 515 68 155 345 3 M39 12 42 430 340 18 12
300 323.9 585 78 175 410 4 M39 16 42 500 400 18 12
53
b
Ød3
Ød4
IS 6392 : 2020 Øk
ØDFlanges for Welding

Table 42 Plate

Ød1
Ød2
f
b
Ød4
Øk
ØD

d1 Dia.
10 17.2 100 18.0 22 40 2 M12 4 14 70

15 21.3 105 22.0 24 45 2 M12 4 14 75
20 26.9 130 27.5 26 58 2 M16 4 18 90
25 33.7 140 34.5 26 68 2 M16 4 18 100
32 42.4 155 43.5 28 78 2 M20 4 22 110
40 48.3 170 49.5 30 88 3 M20 4 22 125

50 60.3 195 61.5 34 102 3 M24 4 26 145
65 76.1 220 77.5 36 122 3 M24 8 26 170
80 88.9 230 90.5 40 138 3 M24 8 26 180
100 114.3 265 116.0 44 162 3 M27 8 30 210
125 139.7 315 141.5 54 188 3 M30 8 33 250

150 168.3 355 170.5 62 218 3 M30 12 33 290
175 193.7 390 195.5 68 260 3 M33 12 36 320
200 219.1 430 221.5 76 285 3 M33 12 36 360
250 273 515 276.5 90 345 3 M39 12 42 430
300 323.9 585 327.5 106 410 4 M39 16 42 500
54
Table 43 Tolerances
( Applicable for all concerned Table )
Dimension Type of Flanges Tolerance Nominal Size

mm
Outside diameter of neck d1 Welding Neck Flanges, +2.5 Upto and inclusive of 150
Integral Flanges. -1.0
+4.0 Over 150 to 600 inclusive
-1.0
+5.5 Over 600
-1.5
Bore Diameter Plate Flanges for welding, +0.5 Upto and inclusive 100
Slip-on Boss Flanges for welding, -0
Loose Flanges for welding on lapped Pipe Ends. +1.0 Over 100 to 400 inclusive
-0
-0
+3.0 Over 600
-0
Outside diameter D Integral Flanges. ±4.0 Upto and inclusive of 250
±5.0 Over 250 to 500 inclusive
±12.0 Over 2000
Welding Neck flanges, ±2.0 Upto and inclusive of 150
Plate for wielding, ±3.0 Over 150 to 500 inclusive
Screwed Boss Flanges, ±5.0 Over 500 to 1200 Inclusive
Slip-on Boss Flanges for wielding,
Loose Flanges for wielded on lapped Pipe Ends,
±10.0 Over 1800
Plate Blank Flanges.
NOTE — In case of 150 mm nominal size pipe having Outside diameter of neck (d1) 165 mm, bore diameter will be 167.5 mm and tolerance
as applicable.
Length through hub h1, h2 Welding Neck Flanges ±1.5 Upto and inclusive 80
Screwed Boss Flanges ±2.0 Over 80 to 250 inclusive
Slip-on Boss Flanges for welding ±3.0 Over 250
Neck /Boss Diameter d3 Integral Flanges, +0 Over and inclusive 50
Wielding Neck Flanges -2.0
+0 Over 50 to 150 inclusive
-4.0
-6.0
-8.0
+0 Over 600
-10.0
IS 6392 : 2020
Table 43 ( Continued )

mm
Screwed Boss Flanges, +1.0 Upto and inclusive 50
Slip-on Boss Flanges for wielding -0
-0
-0
Flange thickness b All Types of Flanges (machined on both faces) ±1.0 Upto and inclusive 18 mm
thickness
±1.5 Over 18 mm to 50 mm thickness
inclusive
±2.0 Over 50 mm thickness
All Types of Flanges +2.0 Upto and inclusive 18 mm
(machined on front face only) -1.3 thickness
+4.0 Over 18 mm to 50 mm thickness

-1.5 inclusive
+7.0 Over 50mm thickness

-2.0
Raised Face Diameter d4 All Types of Flanges +2.0 Upto and inclusive 250
-1.0
+3.0 Over 250
-1.0
Raised Face height f All Types of Flanges +0 2 mm
-1.0
+0 3 mm
-2.0
+0 4 mm
-3.0
+0 5 mm
-4.0
+0 6 mm
-5.0
Diameter of bolt circle k All Types of Flange ±1.5 Bolt Size M10 to M33
±2.0 Bolt Size M36 to M52
Centre to centre adjacent bolt All Types of Flanges ±0.75 Bolt Size M10 to M33
holes
Eccentricity of machined All Types of Flanges 2.0 Upto and inclusive 150
facing diameter
3.0 Over 150 to 500 inclusive
4.0 Over 500
56
IS 6392 : 2020

mm
Bolt hole diameter d2 All Types of Flanges +1.0 Bolt size M10 to M33
-0
+1.5 Bolt size M36 to M52
-0
+2.0 Bolt size M56 to M95
-0
Parallelism between bolting All Types of Flanges (Machined surface) 1° All sizes
bearing surfaces and Flange
All Types of Flanges ( Unmachined surface) 2° All sizes
jointing faces
Table 44 Maximum Inside Diameter

( Clause 8.2.1 )
All dimensions in millmetres
Nominal Size Pipe Maximum Inside diameter of internal

O.D. parallel thread
6 10.2 8.637
8 13.5 11.549
10 17.2 15.054
15 21.3 18.773
20 26.9 24.259
25 33.7 30.471
32 42.4 39.132
40 48.3 45.025
50 60.3 56.836
65 76.1 72.442
80 88.9 85.142
100 114.3 110.288
125 139.7 135.688
150 165.1 161.088
NOTE — Conformity shall be made with ‘go’, ’nogo’ plain gauge.
57
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of Indian Standards Act, 2016 to promote harmonious
development of the activities of standardization, marking and quality certification of goods and attending to
connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced in any form without
the prior permission in writing of BIS. This does not preclude the free use, in the course of implementing the
standard, of necessary details, such as symbols and sizes, type or grade designations. Enquiries relating to
copyright be addressed to the Director (Publications), BIS.
Review of Indian Standards
Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed
periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are
needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards
should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of
‘BIS Catalogue’ and ‘Standards: Monthly Additions’.
This Indian Standard has been developed from Doc No.: MTD 19 (11230).
Amendments Issued Since Publication

Amend No. Date of Issue Text Affected
BUREAU OF INDIAN STANDARDS

Headquarters:
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002
Telephones: 2323 0131, 2323 3375, 2323 9402 Website: www.bis.gov.in
Regional Offices: Telephones
Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg
NEW DELHI 110002 { 2323 7617
2323 3841
Eastern : 1/14 C.I.T. Scheme VII M, V.I.P. Road, Kankurgachi
KOLKATA 700054 { 2337 8499, 2337 8561
2337 8626, 2337 9120
Northern : Plot No. 4-A, Sector 27-B, Madhya Marg
CHANDIGARH 160019 { 265 0206
265 0290
Southern : C.I.T. Campus, IV Cross Road, CHENNAI 600113
{ 2254 1216, 2254 1442
2254 2519, 2254 2315
Western : Manakalaya, E9 MIDC, Marol, Andheri (East)
MUMBAI 400093 { 2832 9295, 2832 7858
2832 7891, 2832 7892
Branches : AHMEDABAD. BENGALURU. BHOPAL. BHUBANESHWAR. COIMBATORE.
DEHRADUN. DURGAPUR. FARIDABAD. GHAZIABAD. GUWAHATI.
HYDERABAD. JAIPUR. JAMMU. JAMSHEDPUR. KOCHI. LUCKNOW.
NAGPUR. PARWANOO. PATNA. PUNE. RAIPUR. RAJKOT. VISAKHAPATNAM.
Published by BIS, New Delhi

Is 6392

Uploaded by

Copyright:

Available Formats

Is 6392

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Is 6392

Uploaded by

Copyright:

Available Formats

SUPPLIED BY BOOK SUPPLY BUREAU UNDER THE LICENSE FROM BIS FOR ANDHRA PRADESH POWER GENERATION CORPORATION

LTD. - VIJAYAWADA ON 9/22/2021 1:09:09 PM (172.21.151.10) VALID UPTO 4/19/2022

स्टील पाइप फ्लैजेंस — विशिष्टि

Steel Pipes Flanges — Specification

ICS 23.040.60; 77.140.75

भारतीय मानक ब्रयू ो

June 2020  Price Group 14

Steel Tubes, Pipes and Fittings Sectional Committee, MTD 19

carbon steel is used, it shall have a tensile strength of

Table 1 Material Specification

Sl No. Classification Specification

Allowable stress value at primary service 6 FLANGES

b) Flanges Over 300 mm Nominal Size — A 9.2 Re-test

Table 2 Welding Neck Flanges

Nominal pressure 0.25 N/mm2.

*These dimensions are not to scale.

Nom Pipe Flange RaisedØFace

Table 3 Plate Flanges for Welding

NOTE — For nominal sizes 10 to 1 000 mm, use Table 5.

‘These dimensions are not to scale*

Nom Pipe Flange Raised Face Bolting Drilling

1400 1420 1575 42 1480 5 M27 36 30 1520

Table 4 Welding Neck Flanges

Nominal pressure 0.60 N/mm2.

*These dimensions are not to scale.

40 48.3 130 14 38 80 3 Ø kM12 4 14 100 62 7 6

125 139.7 240 18 48 178 3 M16 8 18 200 155 10 8

350 355.6 490 22 62 415 4 M20 12 22 445 385 15 12

Nom Pipe Flange Raised Face Bolting Drilling Neck

800 812.8 975 24 70 880 5 M27 24 30 920 842 16 12

1 600 1 620 1 830 34 90 1 710 5 M33 40 36 1 760 1 655 20 16

Nominal pressure 0.60 N/mm2.

*These dimensions are not to scale

Nom Pipe Flange Raised Face Bolting Drilling

40 48.3 130 49.5 16 80 3 M12 4 14 100

125 139.7 240 141.5 20 178 3 M16 8 18 200

Nom Pipe Flange Raised Face Bolting Drilling

800 812.8 975 38 880 5 M27 24 30 920

1 000 1 016 1 175 46 1 080 5 M27 28 30 1 120

1 600 1 620 1 830 74 1 710 5 M33 40 36 1 760

Table 6 Screwed Boss Flanges

Nominal pressure 0.60 N/mm2.

TABLE 7 SLIP-ON BOSS FLANGES FOR WELDING

Nom Pipe Flange Raised Face Bolting Drilling Boss

80 88.9 190 16 34 128 3 M16 4 18 150 110

Nominal pressure 0.60 N/mm2.

TABLE 8 LOOSE FLANGES FOR WELDED ON LAPPED PIPE ENDS

80 88.9 190 90.5 16 34 128 3 M16 4 18 150 110

250 273 375 276.5 22 44 312 3 M16 12 18 335 295

Ø d3 for Welded on Lapped Pipe Ends

Nominal pressure 0.60 N/mm2.

Nom Pipe Flange Bolting Drilling Pipe End

40 48.3 130 12 53 6 M12 4 14 100 80 4

125 139.7 240 14 145 6 M16 8 18 200 178 5

Nom Pipe Flange Bolting Drilling Pipe End

the purchaser and the

Table 9 Plate Black Flanges

Nominal pressure 0.60 N/mm2.

Nom Flange Spigot Bolting Drilling

June 2020 Price Group 14